RCM Handbook-1

NATIONAL AERONAUTICS
AND SPACE ADMINISTRATION
RELIABILITY CENTERED MAINTENANCE

GUIDE FOR
FACILITIES AND COLLATERAL EQUIPMENT
NASA Reliability Centered Maintenance Guide for Facilities and Collateral Equipment
Table of Contents
Chapter 1-Background ........................................................................................................ 1−1
1.1 Introduction ..................................................................................................... 1−1
1.2 Historical Evolution of RCM ........................................................................... 1−1
1.3 Purpose of This Guide...................................................................................... 1−4
1.4 Applicability and Use of This Guide ................................................................ 1−4
Chapter 2Reliability Centered Maintenance (RCM) Approach ............................................ 2−7

2.1 Philosophy ....................................................................................................... 2−7
2.2 RCM Analysis ................................................................................................. 2−7
2.3 RCM Principles ............................................................................................... 2−9
2.4 Failure ........................................................................................................... 2−11
2.4.1 System and System Boundary ........................................................... 2−11
2.4.2 Function and Functional Failure........................................................ 2−13
2.4.3 Failure Modes................................................................................... 2−13
2.4.4 Reliability ......................................................................................... 2−13
2.4.5 Failure Characteristics....................................................................... 2−14
2.4.6 Preventing Failure............................................................................. 2−16
2.5 Failure Modes and Effects Analysis ............................................................... 2−17
2.5.1 Criticality and Probability of Occurrence .......................................... 2−18
2.5.2 Cause of Failure................................................................................ 2−20
2.6 Reliability Centered Maintenance Goals ........................................................ 2−23
2.7 Program Benefits ........................................................................................... 2−24
2.7.1 Safety ............................................................................................... 2−24
2.7.2 Cost .................................................................................................. 2−24
2.7.3 Reliability ......................................................................................... 2−24
2.7.4 Scheduling........................................................................................ 2−24
2.7.5 Efficiency/Productivity ..................................................................... 2−25
2.8 Impact of RCM on the Facilities Life Cycle ................................................... 2−25
Chapter 3 RCM Program Components .............................................................................. 3−27

3.1 Reactive Maintenance.................................................................................... 3B27
3.1.1 Reactive Maintenance Criteria .......................................................... 3B28
3.2 Preventive Maintenance (PM)........................................................................ 3B29
3.2.1 Preventive Maintenance Criteria ....................................................... 3B29
3.2.2 Determining PM Task and Monitoring Periodicity ............................ 3B29
3.3 Predictive Testing & Inspection (PT&I)......................................................... 3B31
3.3.1 Data Correlation ............................................................................... 3B32
3.4 Proactive Maintenance................................................................................... 3B33
3.4.1 Specifications for New/rebuilt Equipment......................................... 3B34
3.4.2 Precision Rebuild and Installation ..................................................... 3B35
3.4.3 Failed-Part Analysis.......................................................................... 3B43
3.4.4 Root-Cause Failure Analysis (RCFA) ............................................... 3B43
February 2000 i
3.4.5 Reliability Engineering ..................................................................... 3B44

3.4.6 Reliability Calculations..................................................................... 3B44
3.4.7 Rebuild Certification/Verification ..................................................... 3B48
3.4.8 Age Exploration................................................................................ 3B48
3.4.9 Recurrence Control ........................................................................... 3B49
3.4.10 Facilities Condition Assessment........................................................ 3B54
Chapter 4 Predictive Testing & Inspection (PT&I) Technologies ...................................... 4B57

4.1 Introduction ................................................................................................... 4B57
4.1.1 Alerts and Alarms ............................................................................. 4B57
4.2 Vibration Monitoring & Analysis................................................................... 4B59
4.2.1 Applications and Techniques ............................................................ 4B59
4.2.2 Limitations ....................................................................................... 4B62
4.2.3 Logistics ........................................................................................... 4B62
4.3 Thermography ............................................................................................... 4B63
4.3.1 Applications...................................................................................... 4B63
4.3.2 Limitations ....................................................................................... 4B64
4.3.3 Logistics ........................................................................................... 4B64
4.4 Passive (Airborne) Ultrasonics....................................................................... 4B65
4.4.1 Applications and Procedures............................................................. 4B65
4.4.2 Limitations ....................................................................................... 4B68
4.4.3 Logistics ........................................................................................... 4B68
4.5 Lubricant and Wear Particle Analysis ............................................................ 4B69
4.5.1 Purpose............................................................................................. 4B69
4.5.2 Standard Analytical Tests ................................................................. 4B70
4.5.3 Special Tests..................................................................................... 4B72
4.5.4 Application ....................................................................................... 4B73
4.5.5 Sampling .......................................................................................... 4B77
4.6 Electrical Condition Monitoring..................................................................... 4B77
4.6.1 Techniques........................................................................................ 4B77
4.6.2 Additional Techniques and Troubleshooting ..................................... 4B84
4.6.3 Applications...................................................................................... 4B86
4.6.4 Logistics ............................................................................................4-87
4.7 Non-Destructive Testing ................................................................................ 4B88
4.7.1 Techniques........................................................................................ 4B89
4.7.2 Location & Intervals ......................................................................... 4B93
4.7.3 Applications...................................................................................... 4B97
4.7.4 Limitations ....................................................................................... 4B97
4.8 Photography....................................................................................................4-99
Chapter 5CRCM Requirements During Facilities Acquisition............................................. 5B101

5.1 Planning....................................................................................................... 5B101
5.2 Design ......................................................................................................... 5B101
5.2.1 Maintainability and Ease of Monitoring .......................................... 5B101
5.2.2 Technology Review ........................................................................ 5B102
5.3 Construction ................................................................................................ 5B103
ii February 2000
5.4 Maintenance and Operations (M&O) ........................................................... 5B104
Chapter 6CRCM Considerations During Facilities Operation.............................................. 6B105

6.1 RCM Program Data ..................................................................................... 6B105
6.2 Maintenance Feedback................................................................................. 6B105
6.3 Maintenance and Operations (M&O) Considerations ................................... 6B106
Chapter 7CRCM Contract Clauses .......................................................................................7B111

7.1 General Contract Clauses............................................................................. 7B112
7.1.1 Measurements and Measurement Data ............................................ 7B112
7.1.2 Bearing Information........................................................................ 7B112
7.1.3 Gearbox Information....................................................................... 7B112
7.1.4 Pumps............................................................................................. 7B113
7.1.5 Centrifugal Compressors................................................................. 7B113
7.1.6 Fans ................................................................................................ 7B113
7.1.7 Vibration Monitoring ...................................................................... 7B114
7.1.8 Vibration Monitoring Locations...................................................... 7B122
7.1.9 Lubricant and Wear Particle Analysis ............................................. 7B124
7.1.10 Thermography ................................................................................ 7B129
7.1.11 Airborne Ultrasonics....................................................................... 7B130
7.1.12 Pulse Echo Ultrasonics.................................................................... 7B131
7.1.13 Motor Circuit Analysis (Complex Phase Impedance) ...................... 7B131
7.1.14 Motor Current Spectrum Analysis................................................... 7B131
7.1.15 Insulation Resistance ...................................................................... 7B131
7.1.16 Surge Testing.................................................................................. 7B131
7.1.17 Start-Up Tests................................................................................. 7B132
7.1.18 Maintainability and Ease of Monitoring .......................................... 7B132
7.1.19 Leveling of Equipment Upon Installation........................................ 7B132
7.2 Architectural/Engineering (A&E) Contracts................................................. 7B132
7.3 Construction Contracts................................................................................. 7B133
7.4 Equipment Procurement Contracts............................................................... 7B134
7.5 Maintenance and Operations (M&O) Contracts ........................................... 7B135
Chapter 8CPT&I Criteria.................................................................................................... 8B137

8.1 Baselines ..................................................................................................... 8B137
8.2 Criteria by PT&I Technology....................................................................... 8B137
8.2.1 Vibration Monitoring ...................................................................... 8B137
8.2.2 Lubricant and Wear Particle Analysis ............................................. 8B139
8.2.3 Thermography ................................................................................ 8B140
8.2.4 Airborne Ultrasonics....................................................................... 8B141
8.2.5 Motor Circuit Analysis.................................................................... 8B142
8.2.6 Motor Current Spectrum Analysis (MCSA) .................................... 8B145
8.2.7 Insulation Resistance ...................................................................... 8B145
8.2.8 Surge Testing.................................................................................. 8B146
8.2.9 Start-Up Tests................................................................................. 8B147
February 2000 iii

Chapter 9CChecklists for RCM Quality Assurance .............................................................. 9B149

9.1 Planning....................................................................................................... 9B149
9.2 Design ......................................................................................................... 9B150
9.3 Construction ................................................................................................ 9B151
9.4 Equipment Procurement............................................................................... 9B151
9.5 Maintenance and Operations ........................................................................ 9B152
Chapter 10CManagement Indicators .................................................................................. 10B153

10.1 General ...................................................................................................... 10B153
10.2 Purpose of Metrics ..................................................................................... 10B153
10.2.1 Metrics Ownership ......................................................................... 10B154
10.2.2 Definition of Metrics ....................................................................... 10-154
10.3 Sample Metrics .......................................................................................... 10B155
10.4 Trending Indicators.................................................................................... 10B156
10.5 Recommended Agencywide Facilities Metrics ........................................... 10B157
10.6 Metric Selection......................................................................................... 10B158
10.7 Benchmark Selection ................................................................................. 10-158
10.8 Utilization of Metrics.................................................................................. 10-158
10.9 Examples of Benchmarks............................................................................ 10-159
10.10 Planning & Scheduling Metrics................................................................... 10-163
10.11 RCM Metrics .............................................................................................. 10-164
Appendix ACGlossary ........................................................................................................ AB167

Appendix BCAbbreviations/Acronyms...............................................................................BB175
Appendix CCBibliography .................................................................................................CB179
Appendix DCSources of PT&I Equipment, Services, and Training .................................... DB185
Appendix ECVibration Criteria ..........................................................................................EB191
Appendix FCPT&I Technologies Correlation Relationships ............................................... FB231
Appendix G—Alignment Standard .................................................................................... GB243
Appendix H—Balance Standard ........................................................................................ HB257
Appendix I—AC Motor Repair and Reconditioning.............................................................IB267
Appendix J—Maintenance Procedures.................................................................................JB275
Appendix K—SPECSINTACT Clauses with RCM Applications ....................................... KB323
List of Tables
2-1. Criticality/Severity Categories...................................................................2-18

2-2. Probability of Occurrence Categories ........................................................2-20
2-3. Chilled Water System Analysis .................................................................2-21
2-4. Electric Motor Component Analysis..........................................................2-22
2-5. Cause of Motor Bearing Failure ................................................................2-23
2-6. RCM Facility Life-Cycle Implications ......................................................2-26
3–1. Maintenance Priority Levels......................................................................3-27
3–2. Reactive Maintenance Priorities ................................................................3-28
iv February 2000
3–3. Balance Quality Grades for Various Groups of Representative Rigid

Rotors (ISO 1940/1-1986).........................................................................3-37
3–4. Recommended Coupled Alignment Tolerances (General Motors, 1993)....3-40
3–5. Alignment Related Tolerances (General Motors, 1993).............................3-40
3–6. Limitations on Rolling Bearing Misalignment (Harris,1984) .....................3-41
3–7. Equipment Condition Classification Based on PT&I Data.........................3-55
4–1. Estimated Steam Loss ...............................................................................4-67
4–2. Recommended Maximum Inspection Intervals (API 570) .........................4-94
6–1. Maintenance Training .............................................................................6-108
7–1. Motor Balance Specifications..................................................................7-118
7–2. Motor Vibration Criteria .........................................................................7-118
7–3. Pump Vibration Limits............................................................................7-119
7–4. Belt-Driven Fan Vibration Limits............................................................7-120
7–5. ISO 3945 Vibration Severity Table. ........................................................7-121
7–6. Vibration Acceptance Classes .................................................................7-121
7–7. Machine Classifications ..........................................................................7-122
7–8. Lubricant Tests .......................................................................................7-126
7–9. Sperry Vickers Table of Suggested Acceptable Contamination Levels
for Various Hydraulic Systems................................................................7-127
7–10. Typical Properties of Transformer Oils ...................................................7-128
7–11. RCM Clauses for A&E Contracts............................................................7-132
7–12. RCM Clauses for Construction Contracts................................................7-134
7–13. RCM Clauses for Equipment Procurement Contracts ..............................7-135
7–14. RCM Clauses for M&O Contracts...........................................................7-136
8–1. Actions Required Based on Temperature Rise Under Load .....................8-141
8–2. Temperature Limits for Selected Components.........................................8-142
9–1. RCM Quality Assurance Planning Considerations...................................9-149
9–2. RCM Quality Assurance Design Considerations......................................9-150
9–3. RCM Quality Assurance Construction Considerations.............................9-151
9–4. RCM Quality Assurance Equipment Procurement Considerations...........9-151
9–5. RCM Quality Assurance Maintenance and Operations Considerations ....9-152
10–1. Financial Benchmarks ........................................................................... 10-160
10–2. Organizational Benchmarks .................................................................. 10-161
10–3. Work Practices Benchmarks.................................................................. 10-161
10–3. Work Practices Data (Cont.).................................................................. 10-162
List of Figures
1-1. Components of an RCM Program................................................................1-1

1-2. Bearing Life Scatter ....................................................................................1-3
1-3. RCM Strategy and Process..........................................................................1-5
2-1. RCM Analysis Considerations ....................................................................2-8
2-2. Maintenance Analysis Process .................................................................2-10
February 2000 v
2-3. Reliability Centered Maintenance (RCM) Decision Logic Tree.................2-12

2-4. Conditional Probability of Failure Curves .................................................2-15
2-5. Preventing Failure.....................................................................................2-17
2-6. FMEA Worksheet .....................................................................................2-19
2-7. Stages of Life-Cycle Cost Commitment ....................................................2-26
3-1. Sample System..........................................................................................3-33
3-2. Effects of Misalignment on Roller Bearings ..............................................3-42
3-3. Determining Network Reliability ..............................................................3-47
3-4. Failure Analysis Form...............................................................................3-53
3-5. Mean and Standard Deviation ...................................................................3-54
3-6. Office Assessment Form ...........................................................................3-56
4-1. PT&I Applications ....................................................................................4-58
4-2. Sound Disc Diagram .................................................................................4-61
4-3. Lubrication Analysis Chart .......................................................................4-76
4-4. Power Factor Current/Voltage Relationship ..............................................4-79
4-5. NDT Technique Selection Process ............................................................4-88
4-6. Shielded Radiography Enclosure...............................................................4-90
4-7. Magnetic Particle Testing..........................................................................4-92
4-8. Inspection Program Development .............................................................4-96
6-1. Design Improvements through Maintenance Feedback............................6-107
7-1. Transducer Response ..............................................................................7-115
8-1. Wear Particle Size and Equipment Condition ..........................................8-140
vi February 2000
Chapter 1 - Background
1.1 Introduction
Reliability Centered Maintenance (RCM) is the process that is used to determine the most
effective approach to maintenance. It involves identifying actions that, when taken, will reduce
the probability of failure and which are the most cost effective. It seeks the optimal mix of
Condition-Based Actions, other Time- or Cycle-Based actions, or a Run-to-Failure approach, as
shown in Figure 1-1. The principal features of each strategy are shown below their block in
Figure 1-1. RCM is an ongoing process that gathers data from operating systems performance
and uses this data to improve design and future maintenance. These maintenance strategies,
rather than being applied independently, are integrated to take advantage of their respective
strengths in order to optimize facility and equipment operability and efficiency while minimizing
life-cycle costs. The elements of RCM are developed in Chapter 2 and the maintenance
strategies are defined and discussed in Chapter 3.
Reliability
Centered
Maintenance
Reactive Preventive Predictive Proactive
• Small items • Subject to wear- • Random failure • RCFA

• Non-critical out patterns • Age
• Inconsequential • Consumable • Not subject to Exploration
• Unlikely to fail replacement wear • FMEA
• Redundant • Failure pattern • PM induced
known failures
Figure 1–1. Components of an RCM Program
1.2 Historical Evolution of RCM

Analysis of maintenance policy in the airline industry in the late 1960's and early 1970's led to
the development of Reliability Centered Maintenance (RCM) concepts. The principles and
applications of RCM were documented in Nowlan and Heap's publication, Reliability-Centered
Maintenance.1 The work demonstrated that a strong correlation between age and failure rate did
not exist and the basic premise of time based maintenance was false for the majority of
equipment. Additional studies performed by the Department of Defense (DOD) and several
nuclear utilities confirmed Nowlan and Heap's work.
1
F. Stanley Nowlan and Howard F. Heap. Reliability-Centered Maintenance. United Airlines and Dolby Press,
sponsored and published by the Office of Assistant Secretary of Defense, 1978.
February 2000 1-1

From approximately 1960 until the late 1980s, Preventive Maintenance (PM) was the most
advanced technique used by progressive facilities maintenance organizations. PM is based on
two principles - 1) a strong correlation exists between equipment age and failure rate, and 2)
individual component and equipment probability of failure can be determined statistically, and
therefore, parts can be replaced or rebuilt prior to failure.
PM assumes that failure probabilities can be determined statistically for individual machines and
components and parts or adjustments can be replaced or performed in time to preclude failure.
For example, a common practice in the past was to replace or renew bearings after some number
of operating hours based on the assumption that bearing failure rate increases with time in
service. This has proven to be ineffective.
Figure 1–2 shows the failure distribution of a group of thirty identical 6309 deep groove ball
bearings installed on bearing life test machines and run to failure. The wide variation in bearing
life is obvious and precludes the use of any effective time-based maintenance strategy2. The X-
axis is the individual bearing being tested while the Y-axis is the number of revolutions achieved
prior to fatigue failure of the individual bearing. It should be noted that the bearings are tested at
above-design loads to accelerate the failure rate. This is the standard procedure used to test
bearings in order to determine the expected life of a bearing.
In all the studies, it was noted that a difference existed between the perceived and the intrinsic
design life for the majority of equipment and components. In fact, it was discovered that in
many cases equipment bearing life greatly exceeded the perceived or stated design life. For
example, SKF Industries proposed changes in the method for evaluating bearing life - from the
original method (empirical) proposed by Lundberg and Palmgren3 to one where "bearings exhibit
a minimum fatigue life; that is, 'crib deaths' due to rolling contact fatigue are non-existent when
the aforementioned operating conditions (properly lubricated, mounted, operated and protected
from dirt and moisture) are achieved."4 This lack of a predefined fatigue life for bearings greatly
impacts the concept of a predetermined design life for rotating equipment where rolling element
bearings are used and provides the basis for extending the time between overhauls and
equipment replacement.
This process, known as Age Exploration (AE), was used by the U.S. Submarine Force in the
early 1970's to extend the time between periodic overhauls and to replace time based tasks with
condition based tasks. While the initial program was limited to Fleet Ballistic Missile (FBM)
submarines, it was continuously expanded until it included all submarines, aircraft carriers, other
major combatants, and ships of the Military Sealift Command (MSC). Furthermore, the Navy
has invoked the requirements of RCM and condition monitoring as part of new ship design
specifications.
It should not be inferred from the above that all interval based maintenance should be replaced
by condition based maintenance. In fact, interval based maintenance is often appropriate for
2
Eschmann, et al, Ball and Roller Bearings: Theory, Design, & Application, John Wiley & Sons, 1985
3
G. Lundberg and A. Palmgren, Dynamic Capacity of Roller Bearings, Acra Polytech, Mechanical Engineering
Series 1, R.S.A.E.E., No. 3, 7, 1947.
4
Tedric A. Harris, Roller Bearing Analysis, Second Edition, John Wiley and Sons, New York, 1984
1-2 February 2000

those instances where an abrasive, erosive, or corrosive wear takes place, material properties
change due to fatigue, embrittlement, etc. and/or a clear correlation between age and functional
reliability exists.
Development of new technologies during the 1990's, including affordable microprocessors and
increased computer literacy in the work force, has made it possible to determine the actual
condition of equipment and not have to rely upon estimates of when the equipment might fail
based on age. These new cost effective technologies and the lack of correlation between age and
failure in many equipment items have increased the emphasis on condition monitoring.
Condition monitoring, commonly called Predictive Testing and Inspection (PT&I) within the
NASA facilities maintenance environment, has resulted in a need to review existing Preventive
(PM) and Programmed (PGM) Maintenance efforts and ensure that the most effective approach
is being used. RCM provides the structure for developing that approach.
Closely aligned with determining what maintenance approach to use are the subjects of who
should do the work and what parts and material will be needed to ensure that the work is done in
the most cost efficient manner.
Most recently, RCM has taken on a prominent role in NASA's facility and equipment
maintenance and operations program. RCM principles have been integrated into the
SPECSINTACT (See Appendix K, Clauses with RCM Applications) wherein designs now have
requirements for designing to maintainability. PT&I is used within the construction contractor's
quality control program before and during commissioning to ensure that there are no latent
manufacturing and installation defects at the time of equipment acceptance. PT&I and proactive
Thirty Identical 6309 Deep Groove

Ball Bearings Run to Fatigue Failure
Under Test Load Conditions
1 5 10 15 20 25 30
Bearing Number From: Ball and Roller Theory,
Design, & Application.
Eschmann, et al
John Wiley & Sons, 1985
Figure 1-2: Bearing Life Scatter
analyses are used as tools by NASA Quality Assurance Evaluators (QAEs) to monitor the
contractor's compliance with the specific requirements of performance based contracts. RCM is
February 2000 1-3

used in developing Condition Assessments and in determining the Backlog of Maintenance and
Repair (BMAR). RCM principles and procedures are used every day in the maintenance of
NASA's facilities where methods, frequencies, periodicities and other criteria are identified in the
Annual, 5-Year, and more frequent Work Plans.
This guide is intended to provide detailed information for aiding in the implementation of RCM
concepts and supporting programs within the NASA facilities community. Intended users
include facility planners, designers, equipment procurement specialists, construction managers,
systems engineers, and maintenance and operations (M&O) contract planners and managers.
Figure 1-3 provides a visual representation of the RCM strategy and process relationship.
1.3 Purpose of This Guide

The purpose of this guide is to provide NASA Headquarters and Center (including Component
Facilities) personnel, Maintenance and Operations (M&O) contractor personnel, and others
involved in NASA facilities maintenance and/or construction a single reference document to be
used to identify the RCM requirements during the facilities life cycle. This guide is intended to
provide the following:
• An Overview of RCM
• An Introduction to Root Cause Failure Analysis
• An Overview of PT&I Technologies
• Guidelines for Establishing Monitoring Intervals
• Requirements for the Certification of PT&I Personnel
• In-service Criteria for Facilities Equipment and Systems
• Guidelines for Developing Procurement Specifications and Criteria
• Contract Clauses for Planning, Design, Construction, and Maintenance
• Guidelines for Performing Facilities Condition Assessment in an RCM

environment
1.4 Applicability and Use of This Guide

This guide, particularly its sample contract clauses, should be used for facilities planning, design,
new construction, modification, equipment procurement, and M&O contracts. It can also be
used in preparing any Requests for Proposals (RFPs) or Requests for Quotations (RFQs) for
facilities contracts and contract modifications. Its sister publication, the NASA Building and
Equipment Commissioning Guide, provides criteria based on RCM principles for equipment
acceptance. Other uses of this guide are recommended in the NASA Facility Maintenance
1-4 February 2000

Management Handbook5. Proactive techniques such as machinery alignment and balance

criteria, Age Exploration, and Facility Condition Assessment (FCA) are also addressed.
RCM Strategy
RCM Process
Maintenance
Outcomes Performance Optimization
Time- or Cycle-Based actions Determine who will perform the
including Inspection, Calibration, maintenance and repair actions.
and Condition Monitoring.
Condition-Based actions
including Overhaul and Repair.
Run-to-Failure of non-safety Proactive

related, low-cost, non-critical,
easy to repair items. Develop standards to select, install,
and test systems and equipment.
Feedback to designers to improve the inherent

reliability, maintainability and supportability.
Spare Parts and
Materials Perform other activities to understand
the cause of failure in order to
Determine material inventory level. eliminate it.
Establish material holding location.
Figure 1-3. RCM Strategy and Process
5
NASA NPG 8831.2, Facilities Maintenance Management Handbook
February 2000 1-5

Intentionally Left Blank
1-6 February 2000

Chapter 2 - Reliability Centered Maintenance (RCM)

Approach
2.1 Philosophy
The RCM philosophy employs Preventive Maintenance (PM), Predictive Testing and Inspection
(PT&I), Repair (also called reactive maintenance) and Proactive Maintenance techniques in an
integrated manner to increase the probability that a machine or component will function in the
required manner over its design life cycle with a minimum of maintenance. The goal of the
philosophy is to provide the stated function of the facility, with the required reliability and
availability at the lowest cost. RCM requires that maintenance decisions be based on
maintenance requirements supported by sound technical and economic justification. As with any
philosophy, there are many paths, or processes, that lead to a final goal. This is especially true
for RCM where the consequences of failure can vary dramatically.
Rigorous RCM analysis has been used extensively by the aircraft, space, defense, and nuclear
industries where functional failures have the potential to result in large losses of life, national
security implications, and/or extreme environmental impact. A rigorous RCM analysis is based
on a detailed Failure Modes and Effects Analysis (FMEA) and includes probabilities of failure
and system reliability calculations. The analysis is used to determine appropriate maintenance
tasks to address each of the identified failure modes and their consequences.
While this process is appropriate for these industries, it is not necessarily the most practical or
best approach to use for facilities systems maintenance. For these systems a streamlined or
intuitive RCM analysis process may be more appropriate. This is due to the high analysis cost of
the rigorous approach, the relative low impact of failure of most facilities systems, the type of
systems and components maintained, and the amount of redundant systems in place. The
streamlined approach uses the same principles as the rigorous, but recognizes that not all failure
modes will be analyzed. NASA has reviewed the various processes in use and has determined
that the most economical and efficient approach is to use a combination of rigorous (formal) and
intuitive analysis depending on system criticality and failure impact. Candidates for rigorous
analysis include, but are not limited to, wind tunnel drive motors, supercomputer facilities, and
mission support systems where single points of failure exist. In addition, a more rigorous
analysis may be needed for those systems and components where the streamlined or intuitive
RCM process has been utilized and the resultant reliability is still unacceptable in terms of
safety, cost, or mission impact.
2.2 RCM Analysis

The RCM analysis carefully considers the following questions:
• What does the system or equipment do; what is its function?
• What functional failures are likely to occur?
February 2000 2-7

• What are the likely consequences of these functional failures?
• What can be done to reduce the probability of the failure, identify the onset of
failure, or reduce the consequences of the failure?
Figures 2-1 and 2-2 illustrate the RCM approach and the interactive streamlined process.
· System Input
Identify System · System Output
and Boundary · Resources
· Constraints
Identify
To what level?
Sub-systems and
- Inconsequential
Components
· Primary or support?
Examine Function · Continuous or intermittent?
· Active or Passive?
Failure
Define Failure and
· Hidden Failure
Failure Modes
· Potential Failure
Environmental, Health, and Safety

Operational/Mission
Identify
· Availability
Consequences of
· Quantity
Failure
· Quality
Cost
Figure 2-1. RCM Analysis Considerations
2-8 February 2000

2.3 RCM Principles

The primary RCM principles are:
a. RCM is Function Oriented—It seeks to preserve system or equipment function,

not just operability for operability's sake. Redundancy of function, through
multiple equipment, improves functional reliability, but increases life cycle cost in
terms of procurement and operating costs.
b. RCM is System Focused—It is more concerned with maintaining system function

than individual component function.
c. RCM is Reliability Centered—It treats failure statistics in an actuarial manner.

The relationship between operating age and the failures experienced is important.
RCM is not overly concerned with simple failure rate; it seeks to know the
conditional probability of failure at specific ages (the probability that failure will
occur in each given operating age bracket).
d. RCM Acknowledges Design Limitations—Its objective is to maintain the

inherent reliability of the equipment design, recognizing that changes in inherent
reliability are the province of design rather than maintenance. Maintenance can, at
best, only achieve and maintain the level of reliability for equipment, which is
provided for by design. However, RCM recognizes that maintenance feedback can
improve on the original design. In addition, RCM recognizes that a difference
often exists between the perceived design life and the intrinsic or actual design life,
and addresses this through the Age Exploration (AE) process.
e. RCM is Driven by Safety and Economics—Safety must be ensured at any cost;

thereafter, cost-effectiveness becomes the criterion.
f. RCM Defines Failure as Any Unsatisfactory Condition—Therefore, failure may

be either a loss of function (operation ceases) or a loss of acceptable quality
(operation continues).
g. RCM Uses a Logic Tree to Screen Maintenance Tasks—This provides a

consistent approach to the maintenance of all kinds of equipment.
h. RCM Tasks Must Be Applicable—The tasks must address the failure mode and
consider the failure mode characteristics.
i. RCM Tasks Must Be Effective—The tasks must reduce the probability of failure
and be cost effective.
February 2000 2-9

Will the failure have

a direct and adverse No
effect on
environment, health,
safety?
Will the failure have
No
a direct and adverse
Yes effect on Mission
Yes (quantity or quality)?
Will the failure result

in other economic No
Yes loss (high cost
damage to machines
Is there an or system)?
No
effective PT&I
technology or
approach?
Yes Candidate
Develop &
schedule PT&I
Is there an
effective Interval-
No
For
task to monitor
Based task?
condition.
Yes Yes
Develop & Redesign system

Develop Condition-
schedule Interval- or accept the Run-to-Fail?
Based task.
Based task. failure risk.
Figure 2-2. Maintenance Analysis Process
j. RCM Acknowledges Three Types of Maintenance Tasks - These tasks are time-
directed (PM), condition-directed (PdM), and failure finding (one of several
aspects of Proactive Maintenance). Time-directed tasks are scheduled when
appropriate. Condition-directed tasks are performed when conditions indicate they
are needed. Failure-finding tasks detect hidden functions that have failed without
giving evidence of pending failure. Run-to-Failure is a conscious decision and is
acceptable for some equipment.
2-10 February 2000

k. RCM is a Living System—It gathers data from the results achieved and feeds this
data back to improve design and future maintenance. This feedback is an
important part of the Proactive Maintenance element of the RCM program.
Note that the maintenance analysis process, as illustrated in Figure 2-2, has only four possible
outcomes:
• Perform Interval (Time- or Cycle-)-Based actions
• Perform Condition-Based actions
• Perform no action and choose to repair following failure
• Or determine that no maintenance action will reduce the probability of failure

AND that failure is not the chosen outcome (Redesign or Redundancy).
These approaches will be discussed further in Chapter 3.
A formal RCM analysis of each system, subsystem, and component is normally performed on
new, unique, high-cost systems such as aircraft and spacecraft systems and structures. This
approach is rarely needed for most facilities and collateral equipment items because their
construction and failure modes are well understood. Regardless of the technique used to
determine the maintenance approach, the approach must be reassessed and validated. Figure 2-3
depicts an iterative RCM process that can be used for a majority of NASA facilities and
collateral equipment.
2.4 Failure
Failure is the cessation of proper function or performance. RCM examines failure at several
levels: the system level, sub-system level, component level, and sometimes even the parts level.
The goal of an effective maintenance organization is to provide the required system performance
at the lowest cost. This means that the maintenance approach must be based upon a clear
understanding of failure at each of the system levels. System components can be degraded or
even failed and still not cause a system failure (A simple example is the failed headlamp on an
automobile. That failed component has little effect on the overall system performance).
Conversely, several degraded components may combine to cause the system to have failed even
though no individual component has itself failed.
2.4.1 System and System Boundary

A system is any user-defined group of components, equipment, or facilities that support an
operational requirement. These operational requirements are defined by mission criticality or by
environmental, health, safety, regulatory, quality, or other NASA-defined requirements. Most
systems can be divided into unique sub-systems along user-defined boundaries. The boundaries
are selected as a method of dividing a system into subsystems when its complexity makes an
analysis by other means difficult.
February 2000 2-11

Will failure of the facility or

equipment items have a direct and
adverse effect on safety or critical
mission operations?
NO YES
Is the item Can redesign solve the

Expendable? problem permanently and cost
effectively?
YES NO NO YES
Is there a PT&I technology (e.g., vibration testing Redesign

or thermography) that will monitor condition and
give sufficient warning (alert/alarm) of an
impending failure?
NO YES
Is PT&I cost
and priority-
justified?
NO YES
Ia there an effective PM task

that will minimize functional
failures?
NO YES
Is establishing
redundancy cost- and
Priority-justified?
NO YES
Accept risk Install redundant Define PM task Define PT&I task

unit(s) and schedule and schedule
Figure 2-3. Reliability Centered Maintenance (RCM) Decision Logic Tree
2-12 February 2000

• A system boundary or interface definition contains a description of the inputs and

outputs that cross each boundary.
• The facility envelope is the physical barrier created by a building, enclosure, or

other structure; e.g., a cooling tower or tank.
2.4.2 Function and Functional Failure

The function defines the performance expectation and can have many elements. Elements
include physical properties, operation performance including output tolerances, and time
requirements such as continuous operation or limited required availability.
Functional failures are descriptions of the various ways in which a system or subsystem can fail
to meet the functional requirements designed into the equipment. A system or subsystem that is
operating in a degraded state but does not impact any of the requirements addressed in paragraph
2.4.1 (Systems and System Boundary) has not experienced a functional failure.
It is important to determine all the functions of an item that are significant in a given operational
context. By clearly defining the functions' non-performance, the functional failure becomes
clearly defined. For example, it is not enough to define the function of a pump to move water.
The function of the pump must be defined in terms of how much water, at what pressure, at what
efficiency, etc.
2.4.3 Failure Modes

Failure modes are equipment- and component-specific failures that result in the functional failure
of the system or subsystem. For example, a machinery train composed of a motor and pump can
fail catastrophically due to the complete failure of the windings, bearings, shaft, impeller,
controller, or seals. In addition, a functional failure also occurs if the pump performance
degrades such that there is insufficient discharge pressure or flow to meet operating
requirements. These operational requirements should be considered when developing
maintenance tasks.
Dominant failure modes are those failure modes responsible for a significant proportion of all the
failures of the item. They are the most common modes of failure.
Not all failure modes or causes warrant preventive or predictive maintenance because the
likelihood of their occurring is remote or their effect is inconsequential.
2.4.4 Reliability
Reliability is the probability that an item will survive a given operating period, under specified
operating conditions, without failure. The conditional probability of failure measures the
probability that an item entering a given age interval will fail during that interval. If the
conditional probability of failure increases with age, the item shows wear-out characteristics.
The conditional probability of failure reflects the overall adverse effect of age on reliability. It is
not a measure of the change in an individual equipment item.
February 2000 3-13

Failure rate or frequency plays a relatively minor role in maintenance programs because it is too
simple a measure. Failure frequency is useful in making cost decisions and determining
maintenance intervals, but it tells nothing about which maintenance tasks are appropriate or
about the consequences of failure. A maintenance solution should be evaluated in terms of the
safety or economic consequences it is intended to prevent. A maintenance task must be
applicable (i.e., prevent failures or ameliorate failure consequences) in order to be effective.
2.4.5 Failure Characteristics

Conditional probability of failure (Pcond) curves fall into six basic types, as graphed (Pcond vs.
Time) in Figure 2-4. The percentage of equipment conforming to each of the six wear patterns
as determined in three separate studies is also shown in Figure 2-4.
Type A - Constant or gradually increasing failure probability, followed by a pronounced

wear-out region. An age limit may be desirable. (Typical of reciprocating engines.)
Type B - Infant mortality, followed by a constant or slowly increasing failure probability.

(Typical of electronic equipment.)
Type C - Low failure probability when the item is new or just overhauled, followed by a
quick increase to a relatively constant level.
Type D - Relatively constant probability of failure at all ages.
Type E - Bathtub curve; i.e., infant mortality followed by a constant or gradually

increasing failure probability and then a pronounced wear-out region. An age limit may
be desirable, provided a large number of units survive to the age where wear-out begins.
Type F - Gradually increasing failure probability, but no identifiable wear-out age. Age
limit usually not applicable. (Typical of turbine engines.)
Types A and E are typical of single-piece and simple items such as tires, compressor blades,
brake pads, and structural members. Most complex items have conditional probability curves of
types B, C, D, and F.
The basic difference between the failure patterns of complex and simple items has important
implications for maintenance. Single-piece and simple items frequently demonstrate a direct
relationship between reliability and age. This is particularly true where factors such as metal
fatigue or mechanical wear are present or where the items are designed as consumables (short or
predictable life spans). In these cases an age limit based on operating time or stress cycles may
be effective in improving the overall reliability of the complex item of which they are a part.
3-14 February 2000

Age Related Failures UAL BROMBERG U.S. NAVY

Age Related Failures 1968 1982
Type E
1973
4% 3% 3%
Type A
2% 1% 17%
Type F
5% 4% 3%
Time
Type C
7% 11% 6%
Type D
14% 15% 42%
Type B
68% 66% 29%
Time
Figure 2-4. Conditional Probability of Failure Curves.
Complex items frequently demonstrate some infant mortality, after which their failure
probability increases gradually or remains constant, and a marked wear-out age is not common.
In many cases scheduled overhaul increases the overall failure rate by introducing a high infant
mortality rate into an otherwise stable system. The failure characteristics shown in Figure 2-4
February 2000 3-15

were first noted in the previously cited book, Reliability-Centered Maintenance6. Follow-on
studies in Sweden in 1973, and by the U.S. Navy in 1983, produced similar results. In these
three studies, random failures accounted for 77-92% of the total failures and age related failure
characteristics for the remaining 8-23%.
2.4.6 Preventing Failure

Every equipment item has a characteristic that can be called resistance to or margin to failure.
Using equipment subjects it to stress that can result in failure when the stress exceeds the
resistance to failure. Figure 2-5 depicts this concept graphically. The figure shows that failures
may be prevented or item life extended by:
a. Decreasing the amount of stress applied to the item. The life of the item is
extended for the period f0-f1 by the stress reduction shown.
b. Increasing or restoring the item’s resistance to failure. The life of the item is
extended for the period f1-f2 by the resistance increase shown.
c. Decreasing the rate of degradation of the item's resistance to or margin to failure.

The life of the item is extended for the period f2 - f3 by the decreased rate of
resistance degradation shown.
Stress is dependent on use and may be highly variable. It may increase, decrease, or remain
constant with use or time. A review of the failures of a large number of nominally identical
simple items would disclose that the majority had about the same age at failure, subject to
statistical variation, and that these failures occurred for the same reason. If one is considering
preventive maintenance for some simple item and can find a way to measure its resistance to
failure, one can use that information to help select a preventive task.
Adding excess material that wears away or is consumed can increase resistance to failure.
Excess strength may be provided to compensate for loss from corrosion or fatigue. The most
common method of restoring resistance is by replacing the item.
The resistance to failure of a simple item decreases with use or time (age), but a complex unit
consists of hundreds of interacting simple items (parts) and has a considerable number of failure
modes. In the complex case, the mechanisms of failure are the same, but they are operating on
many simple component parts simultaneously and interactively so that failures no longer occur
for the same reason at the same age. For these complex units, it is unlikely that one can design a
maintenance task unless there are a few dominant or critical failure modes.
6
F. Stanley Nowlan and Howard F. Heap, Reliability Centered Maintenance, United Airlines and Dolby Press,
sponsored and published by the Office of Assistant Secretary of Defense, 1978
3-16 February 2000

Increase or
Restore Resistance
Resistance
Decrease Rate
of Degradation
Stress
f0 f1 f2 f3
Life Extension
Operating Age
Figure 2-5. Preventing Failure
2.5 Failure Modes and Effects Analysis

Failure Modes and Effects Analysis (FMEA) is applied to each system, sub-system, and
component identified in the boundary definition. For every function identified, there can be
multiple failure modes. The FMEA addresses each system function (and, since failure is the loss
of function, all possible failures), and the dominant failure modes associated with each failure,
and then examines the consequences of the failure. What effect did the failure have on the
Mission or operation, the system and on the machine?
Even though there are multiple failure modes, often the effects of the failure are the same or very
similar in nature. That is, from a system function perspective, the outcome of any component
failure may result in the system function being degraded.
Likewise, similar systems and machines will often have the same failure modes. However, the
system use will determine the failure consequences. For example, the failure modes of a ball
bearing will be the same regardless of the machine. However, the dominate failure mode will
often change from machine to machine, the cause of the failure may change, and the effects of
the failure will differ.
February 2000 3-17

Figure 2-6 provides an example of a FMEA worksheet. The key elements identified on the
worksheet reflect the items identified in the RCM analysis (see Figure 2-1). There are two new
terms identified in Figure 2-6: Criticality and Probability of Failure Occurrence.
2.5.1 Criticality and Probability of Occurrence

Criticality assessment provides the means for quantifying how important a system function is
relative to the identified Mission. Table 2-1 provides a method for ranking system criticality.
This system, adapted from the automotive industry7, provides 10 categories of
Criticality/Severity. It is not the only method available. The categories can be expanded or
contracted to produce a site-specific listing.
Ranking Effect Comment

No reason to expect failure to have any effect on Safety,
1 None
Health, Environment or Mission.
Minor disruption to facility function. Repair to failure can
2 Very Low
be accomplished during trouble call.
Minor disruption to facility function. Repair to failure may
3 Low
be longer than trouble call but does not delay Mission.
Low to Moderate disruption to facility function. Some portion of
4
Moderate Mission may need to be reworked or process delayed.
Moderate disruption to facility function. 100% of Mission
5 Moderate
may need to be reworked or process delayed.
Moderate Moderate disruption to facility function. Some portion of
6
to High Mission is lost. Moderate delay in restoring function.
High disruption to facility function. Some portion of
7 High
Mission is lost. Significant delay in restoring function.
Very High disruption to facility function. All of Mission is lost.
8
High Significant delay in restoring function.
Potential Safety, Health or Environmental issue. Failure
9 Hazard
will occur with warning.
Potential Safety, Health or Environmental issue. Failure
10 Hazard
will occur without warning.
Table 2-1. Criticality/Severity Categories
7
Reliability, Maintainability, and Supportability Guidebook, Third Edition, Society of Automotive Engineers, Inc.,
Warrendale, PA, 1995.
3-18 February 2000

Page 1 of ____
Printed: Date and
February 2000
Identify Center, Building, Time
System Name
: If Used
: Who prepared this FMEA
Control Name & Function/ Criticality Probability

Potential Failure Mode Potential Failure Effects Remarks/Continue
Number Performance Requirement Rank of Occurrence
Figure 2-6. FMEA Worksheet
3-19
The Probability of Occurrence (of Failure) is also based on work in the automotive industry.
Table 2-2 provides one possible method of quantifying the probability of failure. If there is
historical data available, it will provide a powerful tool in establishing the ranking. If the
historical data is not available, a ranking may be estimated based on experience with similar
systems in the facilities area. The statistical column in Table 2-2 can be based on operating
hours, day, cycles, or other unit that provides a consistent measurement approach. Likewise, the
statistical bases may be adjusted to account for local conditions. For example, one organization
changed the statistical approach for ranking 1 through 5 to better reflect the number of cycles of
the system being analyzed.
Ranking Effect Comment

Remote probability of occurrence; unreasonable to
1 1/10,000
expect failure to occur.
Low failure rate. Similar to past design that has, in the
2 1/5,000
past, had low failure rates for given volume/loads.
Low failure rate. Similar to past design that has, in the
3 1/2,000
past, had low failure rates for given volume/loads.
Occasional failure rate. Similar to past design that has,
4 1/1,000 in the past, had similar failure rates for given
volume/loads.
Moderate failure rate. Similar to past design that has, in
5 1/500 the past, had moderate failure rates for given
volume/loads.
Moderate to high failure rate. Similar to past design that
6 1/200 has, in the past, had moderate failure rates for given
volume/loads.
High failure rate. Similar to past design that has, in the
7 1/100
past, had high failure rates that has caused problems.
High failure rate. Similar to past design that has, in the
8 1/50
past, had high failure rates that has caused problems.
9 1/20 Very High failure rate. Almost certain to cause problems.
10 1/10+ Very High failure rate. Almost certain to cause problems.
Table 2-2. Probability of Occurrence Categories
2.5.2 Cause of Failure

Once the function and failure modes are understood, it is necessary to investigate the cause of
failure. Without an understanding of the causes of potential failure modes it will not be possible
to select applicable and effective maintenance tasks. For example, the type and progression of
information collected for a chilled water system could look similar to Table 2-3.
3-20 February 2000

Each of the individual components that makes up the chilled water system would then have a
similar analysis performed, as illustrated in Table 2-4:
Source of
Function Functional Failure Failure Mode
Failure
See next table.

Provide chilled Electric Motor Failed
water at specified: Pump Failed
Flow Rate Total loss of flow. Major Leak
Temperature Blocked Line
------------------- Valve out of position.
The flow and Pump Cavitation
temperature Drive Problem
would be based Insufficient Flow Blocked Line
upon the use
Valve out of position.
requirement. For
Instrumentation Error
example, if the
Chiller Failure
chilled water
system were Low Refrigerant
supplying a Cooling Tower
computer room, Problem
what would the Water temperature Valve out of position.
water flow and high or low. Fouled Heat
temperature Exchanger
range be to Instrumentation Error
maintain the room
temperature?
Table 2-3. Chilled Water System Analysis
February 2000 3-21

Function Functional Failure Failure Mode Source of Failure

Stator Motor will not turn. Insulation Failure Insulation
contamination,
Open Winding excessive current,
voltage spike,
phase imbalance,
excessive
temperature.
Rotor Motor will not turn. Insulation Failure Insulation
contamination,
Motor turns at Excessive Vibration excessive current,
wrong speed. excessive
temperature,
mechanical
imbalance.
Bearings Motor will not turn. Bearing Seized Fatigue, improper
lubrication,
misalignment,
mechanical
imbalance,
electrical pitting,
lube
contamination,
excessive thrust,
excessive
temperature.
Motor Controller Motor will not turn. Contactor Failed Contact failure,
control circuit
Motor turns at VFD Malfunction failure, cable
wrong speed. failure, loss of
power.
Power Supply Motor will not turn. Loss of Power Supply failure,
excessive current,
excessive torque,
poor connection.
Table 2-4. Electric Motor Component Analysis
Table 2-5 focuses on one failure mode, the seized bearing. Similar information will be needed
for each failure mode. This information can become extensive for even the simplest of systems
and can require a significant amount of effort and expense to compile. Table 2-5 is an
abbreviated and simplistic compilation.
3-22 February 2000

Notice that through the iterative, albeit simplified, process illustrated above, the engineer or
technician performing the analysis is able to determine the root cause of the problem by
deducting non-indicative symptoms and conditions. Medical doctors follow similar reasoning in
their determination of patients' health problems - they eliminate the non-symptoms, then through
an iterative process, deduct each possible cause of the problem, starting with the most likely first.
Failure Mode Mechanism Reason Cause

Bearing seized Lubrication Contamination Seal Failed
(this includes Supply Dirty
seals, shields, Wrong Type Procedure or supply
lubrication information wrong.
system, and lock Too Little Oil leak.
nuts.
Procedure error.
Too Much Procedure error.
Fatigue Metallurgical Inherent
Excessive temperature.
Excessive Mechanical imbalance.
Load Misalignment
Wrong Application
(bearing not sized for the
load).
Poor Fit-up
Surface Distress Installation Procedure error.
Storage Procedure error.
Electrical Insulation
Welding
Contamination See Lubrication
Table 2-5. Cause of Motor Bearing Failure
2.6 Reliability Centered Maintenance Goals

The RCM goals are to identify for each system and equipment the failure modes and their
consequences and to determine the most cost-effective and applicable maintenance technique to
minimize the risk and impact of failure. This allows system and equipment functionality to be
maintained in the most economical manner. Specific RCM objectives as stated by Nowlan and
Heap8 are:
• To ensure realization of the inherent safety and reliability levels of the equipment.
8
F. Stanley Nowlan and Howard F. Heap, Reliability Centered Maintenance, United Airlines and Dolby Press,
sponsored and published by the Office of Assistant Secretary of Defense, 1978
February 2000 3-23

• To restore the equipment to these inherent levels when deterioration occurs.
• To obtain the information necessary for design improvement of those items where
their inherent reliability proves to be inadequate.
• To accomplish these goals at a minimum total cost, including maintenance costs,

support costs, and economic consequences of operational failures.
2.7 Program Benefits
2.7.1 Safety
Per NPD 8700.1, NASA Policy for Safety and Mission Success, NASA policy is to "Avoid loss of
life, personal injury or illness, property loss or damage, or environmental harm from any of its
activities and ensure safe and healthful conditions for persons working at or visiting NASA
facilities." By its very features, including analysis, monitoring, taking decisive action on systems
before they become problematic, and thorough documentation, RCM is highly supportive of and
an integral part of the NASA Safety policy.
2.7.2 Cost
Due to the initial investment required for obtaining the technological tools, training, and
equipment condition baselines, a new RCM Program typically results in a short-term increase in
maintenance costs. This increase is relatively short-lived. The cost of repair decreases as
failures are prevented and preventive maintenance tasks are replaced by condition monitoring.
The net effect is a reduction of both repair and a reduction in total maintenance cost. Often
energy savings are also realized from the use of PT&I techniques.
2.7.3 Reliability
RCM places great emphasis on improving equipment reliability, principally through the feedback
of maintenance experience and equipment condition data to facility planners, designers,
maintenance managers, craftsmen, and manufacturers. This information is instrumental for
continually upgrading the equipment specifications for increased reliability. The increased
reliability that comes from RCM leads to fewer equipment failures and, therefore, greater
availability for mission support and lower maintenance costs.
2.7.4 Scheduling
The ability of a condition-monitoring program to forecast maintenance provides time for
planning, obtaining replacement parts, and arranging environmental and operating conditions
before the maintenance is done. PT&I reduces the unnecessary maintenance performed by a
time-scheduled maintenance program which tends to be driven by the minimum “safe” intervals
between maintenance tasks.
3-24 February 2000

A principal advantage of RCM is that it obtains the maximum use from equipment. With RCM,
equipment replacement is based on equipment condition, not on the calendar. This condition-
based approach to maintenance thereby extends the operating life of the facility and its
equipment.
2.7.5 Efficiency/Productivity
Safety is the primary concern of RCM. The second most important concern is cost-effectiveness.
Cost-effectiveness takes into consideration the priority or mission criticality and then matches a
level of cost appropriate to that priority. The flexibility of the RCM approach to maintenance
ensures that the proper type of maintenance is performed on equipment when it is needed.
Maintenance that is not cost effective is identified and not performed.
2.8 Impact of RCM on the Facilities Life Cycle

The facilities life cycle is often divided into two broad stages: acquisition (planning, design, and
construction) and operations. RCM affects all phases of the acquisition and operations stages to
some degree, as shown in Table 2-6.
Decisions made early in the acquisition cycle profoundly affect the life-cycle cost of a facility.
Even though expenditures for plant and equipment may occur later during the acquisition
process, their cost is committed at an early stage. As shown conceptually in Figure 2-7, planning
(including conceptual design) fixes two-thirds of the facility’s overall life-cycle costs. The
subsequent design phases determine an additional 29% of the life-cycle cost, leaving only about
5% of the life-cycle cost that can be impacted by the later phases.
Thus, the decision to include a facility in an RCM program, including PT&I and condition
monitoring, which will have a major impact on its life-cycle cost, is best made during the
planning phase. As RCM decisions are made later in the life cycle, it becomes more difficult to
achieve the maximum possible benefit from the RCM program.
Even though maintenance is a relatively small portion of the overall life-cycle cost, typically 3%
to 5% of a facility’s operating cost, RCM is still capable of introducing significant savings
during the M&O phase of the facility’s life. Savings of 30% to 50% in the annual maintenance
budget are often obtained through the introduction of a balanced RCM program.
February 2000 3-25

Life-Cycle Phase Acquisition Implications Operations Implications

Planning Requirements Validation Requirements
Contract Strategy Development
RCM Implementation Policy Modifications
Funding Estimates Alterations
Construction Upgrades
Equipment (Collateral/R&D) A&E Scope of Work
Labor Funding Estimates
Training M&O Considerations
Operations Annual Cost
A&E Scope of Work Labor
Spare Parts
Design A&E Selection A&E Selection
Drawings Drawings
Specifications Specifications
Acceptance Testing Acceptance Testing
Requirements Requirements
Construction Contractor Selection Contractor Selection
Mobilization Construction
Construction Acceptance Testing
Activation
Maintenance and Not Applicable RCM Operations
Operation (M&O) Training/Certification
Table 2-6. RCM Facility Life-Cycle Implications
100%
95%
75% 66%
Life-
cycle
Cost 50%
25%
Conceptual Construction/
Design Final Commissioning
Planning Maintenance
Design
& Operations
Blanchard, B.S., Design and
Manage to Life Cycle Cost,
Forest Grove, OR, MA
Life-Cycle
Press, 1978.
Figure 2-7. Stages of Life-Cycle Cost Commitment
3-26 February 2000

Chapter 3—RCM Program Components
An RCM program includes reactive, preventive, predictive, and proactive maintenance. In

addition, a user should understand system boundaries and facility envelopes, functional failures,
and failure modes, all of which are critical components of the RCM program. The following
paragraphs describe these key RCM components.
Table 3–1 suggests the criteria to be used in determining RCM priorities.
Priority
Application
Number Description
1 Emergency Safety; mission impact.
2 Urgent Continuous operation of

facility at risk.
3 Priority Mission support/project
deadlines.
4 Routine Accomplish on “first
come, first served” basis.
5 Discretionary Desirable, but not
essential
6 Deferred Needed but unable to
accomplish until more
resources available.
Table 3–1. Maintenance Priority Levels
3.1 Reactive Maintenance

Reactive maintenance also is referred to as breakdown, repair, fix-when-fail, or run-to-failure
(RTF) maintenance. When applying this maintenance technique, maintenance, equipment repair,
or replacement occurs only when the deterioration in the equipment’s condition causes a
functional failure. This type of maintenance assumes that failure is equally likely to occur in any
part, component, or system. Thus, this assumption precludes identifying a specific group of
repair parts as being more necessary or desirable than others. If the item fails and repair parts are
not available, delays ensue while parts are obtained. If certain parts are urgently needed to
restore a critical machine or system to operation, a premium for expedited delivery must be paid.
Also, there is no ability to influence when the failures occur because no (or minimal) action is
taken to control or prevent them. When this is the sole type of maintenance practiced, a high
February 2000 3-27

percentage of unplanned maintenance activities, high replacement part inventories, and

inefficient use of maintenance effort typify this strategy. A purely reactive maintenance program
ignores the many opportunities to influence equipment survivability. Reactive maintenance can
be used effectively when it is performed as a conscious decision based on the results of an RCM
analysis that compares the risk and cost of failure with the cost of the maintenance required to
mitigate that risk and cost of failure.
Examples of components where RTF is applicable are non-critical electric motors less than 7.5
HP, comfort cooling, restroom exhaust fans, water heaters, and items where the consequences of
failure are negligible.
3.1.1 Reactive Maintenance Criteria

Table 3–2 suggest criteria to be used in determining the priority for repairing or replacing the
failed equipment in the reactive maintenance program.
Priority Criteria Based on

Consequences of
Number Description Equipment/System Failure
1 Emergency Safety of life or property
threatened.
Immediate serious impact on
mission.
2 Urgent Continuous facility operation
threatened.
Impending serious impact on
mission.
3 Priority Degrades quality of mission
support.
Significant and adverse effect
on project.
4 Routine Redundancy available.
Impact on mission insignificant.
5 Discretionary Impact on mission negligible.
Resources available.
6 Deferred Impact on mission negligible.
Resources unavailable.
Table 3–2. Reactive Maintenance Priorities
3-28 February 2000

3.2 Preventive Maintenance (PM)

PM consists of regularly scheduled inspection, adjustments, cleaning, lubrication, parts
replacement, calibration, and repair of components and equipment. PM is also referred to as
time-driven or interval-based maintenance. It is performed without regard to equipment
condition.
PM schedules periodic inspection and maintenance at pre-defined intervals (time, operating

hours, or cycles) in an attempt to reduce equipment failures for susceptible equipment.
Depending on the intervals set, PM can result in a significant increase in inspections and routine
maintenance; however, it should also reduce the frequency and seriousness of unplanned
machine failures for components with defined, age-related wear patterns.
Traditional PM is keyed to failure rates and times between failures. It assumes that these
variables can be determined statistically, and therefore one can replace a part due for failure
before it fails. The availability of statistical failure information tends to lead to fixed schedules
for the overhaul of equipment or the replacement of parts subject to wear. PM is based on the
assumption that the overhaul of machinery by disassembly and replacement of worn parts
restores the machine to a like-new condition with no harmful effects. In addition, this renewal
task is based on the perception new components are less likely to fail than old components of the
same design. See Figures 1–2 and 2–3.
Failure rate or its reciprocal, Mean-Time-Between-Failures (MTBF), is often used as a guide to

establishing the interval at which the maintenance tasks should be performed. The major
weakness in using these measurements to establish task periodicity is that failure rate data
determines only the average failure rate. The reality is failures are equally likely to occur at
random times and with a frequency unrelated to the average failure rate. Thus, selecting a
specific time to conduct periodic maintenance for a component with a random failure pattern is
difficult at best.
For some items, while failure is related to age, it is not equally likely to occur throughout the life
of the item. In fact, the majority of equipment is not subject to wear-out (sharply increasing
conditional probability of failure at a specific operating age). Therefore, timed maintenance can
often result in unnecessary maintenance. In summary, PM can be costly and ineffective when it
is the sole type of maintenance practiced.
3.2.1 Preventive Maintenance Criteria

Preventive maintenance criteria reflect the age-reliability characteristics of the equipment based
upon the equipment history. They are not necessarily related to mission criticality. The
selection of maintenance tasks is made using the process shown in Figure 2–1. The selection
process guides the determination of the type of task which, will be done, but is less helpful in
establishing task frequency or periodicity.
3.2.2 Determining PM Task and Monitoring Periodicity

This section offers suggestions for selecting monitoring periodicities.
February 2000 3-29

3.2.2.1 PM Tasks
Although numerous ways have been proposed for determining the correct periodicity of
preventive maintenance tasks, none are valid unless the in-service age-reliability characteristics
of the system or equipment affected by the desired task are known. This information is not
normally available and must always be collected for new systems and equipment. PT&I
techniques should be used as an aid in determining equipment condition vs. age.
Careful analysis of similar kinds of hardware in industry has shown that, overall, more than 90%
of the hardware analyzed showed no adverse age-reliability relationship. This does not mean
that individual parts do not wear; they do. It means that the ages at failure are distributed in such
a way that there is no value in imposing a preventive maintenance task. In fact, in a large
number of cases, imposing an arbitrary preventive task increases the average failure rate through
“infant mortality.”
The Mean Time Between Failures (MTBF) is often used as the initial basis for determining PM
interval. This approach is incorrect in that it does not provide any information about the effect of
increasing age on reliability. It provides only the average age at which failure occurs, not the
most likely age. In many cases a Weibull distribution, as used by the bearing industry to specify
bearing life, will provide more accurate information on the distribution of failures.
The best thing that can be done if good information on the effect of age on reliability is not
available, is to monitor the equipment condition.
3.2.2.2 Equipment Monitoring

The factors above still apply, but with several important modifications. The aim in monitoring
equipment condition is to (1) determine equipment condition and (2) develop a trend with which
to forecast future equipment condition. For trending purposes, a minimum of three monitoring
points before failure may reasonably be expected are recommended. Using three data points
provides two to establish the trend and the third to provide confirmation. The following
techniques are recommended for setting initial periodicity:
a. Anticipating Failure from Experience.
For some equipment, failure history and personal experience provide an intuitive feel as to when
equipment failure may be expected. In these cases, failure is time related. The monitoring
periodicity should be selected such that there are at least three monitoring intervals before the
anticipated onset of failures. It is prudent in most cases to shorten the monitoring interval as the
wear-out age is approached.
b. Failure Distribution Statistics.
In using statistics to determine the basis for selecting task periodicity, the distribution and
probability of failure should be known. Weibull distributions can provide information on the
probability of an equipment exceeding some life. For example, bearings are normally specified
by their B10 life; i.e., the number of revolutions that will be exceeded by 90% of the bearings.
3-30 February 2000

Depending on the criticality of the equipment, an initial periodicity is recommended which

allows a minimum of three monitoring samples prior to the B10 life or, in less severe cases, prior
to the MTBF point. In more severe cases a B2 life; i.e., the number of revolutions that will be
exceeded by 98% of the bearings should be specified and the monitoring interval adjusted
accordingly.
c. Lack of Information or Conservative Approach.
The most common practice in industry is to monitor the equipment biweekly or monthly due to a
lack of information and poor monitoring techniques. This often results in excessive monitoring.
In these cases, significant increases in the monitoring interval may be made without adverse
impact on equipment reliability.
When indications of impending failure become apparent through trending or other predictive
analysis methods, the monitoring interval should be reduced and additional analysis should be
performed in order to gain more detailed information on the condition of the equipment.
3.3 Predictive Testing & Inspection (PT&I)

PT&I, also known as predictive maintenance or condition monitoring, uses primarily non-
intrusive testing techniques, visual inspection, and performance data to assess machinery
condition. It replaces arbitrarily timed maintenance tasks with maintenance that is scheduled
only when warranted by equipment condition. Continuing analysis of equipment condition-
monitoring data allows planning and scheduling of maintenance or repairs in advance of
catastrophic and functional failure.
The PT&I data collected is used in one of following ways to determine the condition of the
equipment and identify the precursors of failure. The methods of analysis include:
• Trend analysis
• Pattern recognition
• Data comparison
• Tests against limits and ranges
• Correlation of multiple technologies
• Statistical process analysis
PT&I does not lend itself to all types of equipment or possible failure modes and therefore
should not be the sole type of maintenance practiced.
Refer to Chapter 4 for information on PT&I technologies.
February 2000 3-31

3.3.1 Data Correlation

Data acquired from the various PT&I techniques can and should be correlated with each other to
increase the probability of detection (Pd). The tables in Appendix F provide correlation between
the various PT&I technologies:
Figure 3–1 depicts a simplified Chilled Water System and the various components that can be
monitored using the aforementioned correlated PT&I technologies. For example, a chilled water
system would require the following PT&I techniques to be used for the entire system to be
evaluated:
a. Flow Rates—Flow would be measured using precision, non-intrusive flow detectors.
b. Temperature—Differential temperature would be measured to determine heat

transfer coefficients and to indicate possible fouling of tubes.
c. Pressure—Differential pump and chiller pressures would be measured to determine

pressure drops and pump efficiency.
d. Electrical—Motor power consumption and motor circuit testing would be used to

assess the condition of the motor circuits and to correlate with pump efficiencies.
e. Ultrasonic Thickness—Pipe wall thickness would be measured to determine erosion

and corrosion degradation.
f. Vibration—Vibration monitoring would be used to assess the condition of the rotating

components such as pumps and motors. Additionally, structural problems would be
identified through resonance and model testing.
g. Lubricant Analysis—Oil condition and wear particle analysis would be used to

identify problems with the lubricant and correlated with vibration when wear particle
concentrations exceed pre-established limits.
h. Fiber Optics—Fiber optic inspections would be used in response to indications of

component wear, tube fouling, etc.
i. Thermography—Thermography scans would be used to check motor control centers

and distribution junction boxes for high temperature conditions. Piping insulation should
be checked for porosities.
j. Eddy Current—Eddy current would be used to determine and locate leaking tubes.
k. Airborne Ultrasonics—Airborne Ultrasonics would be used to detect leaking air

from control system and compressor leaks.
3-32 February 2000

Figure 3 – 1. Sample System
3.4 Proactive Maintenance

Proactive maintenance employs the following basic techniques to extend machinery life:
• Specifications for new/rebuilt equipment
• Precision rebuild and installation
• Failed-part analysis
• Root-cause failure analysis
• Reliability engineering
• Rebuild certification/verification
• Age Exploration
• Recurrence Control
Proactive maintenance improves maintenance through better design, installation, maintenance

procedures, workmanship, and scheduling.
February 2000 3-33

The characteristics of proactive maintenance are:
• Using feedback and communications to ensure that changes in design or

procedures are rapidly made available to designers and managers.
• Employing a life-cycle view of maintenance and supporting functions.
• Ensuring that nothing affecting maintenance occurs in isolation.
• Employing a continuous process of improvement.
• Optimizing and tailoring maintenance techniques and technologies to each

application.
• Integrating functions that support maintenance into maintenance program

planning.
• Using root-cause failure analysis and predictive analysis to maximize mainte-

nance effectiveness.
• Adopting an ultimate goal of fixing the equipment forever.
• Periodic evaluation of the technical content and performance interval of

maintenance tasks (PM and PT&I).
A proactive maintenance program is the capstone of the RCM philosophy. The seven most
commonly recognized proactive techniques listed above are described in the following.
3.4.1 Specifications for New/Rebuilt Equipment

The design and fabrication of many new types of equipment too often fail to provide the
capability to obtain reliable equipment condition data easily while the equipment is operating. It
has been alleged that this oversight might result from design using CAD/CAM systems that
require little practical experience on the part of the designers. Existing standards, often 25 to 30
years old and not reflective of changes in technology, are usually inadequate, typically
addressing only general or minimal performance criteria. Additionally, the life-cycle costs and
failure histories of families of equipment are rarely documented for purchasing and contract
personnel who, bound by regulation, procure conforming products based on least cost.
To solve this problem, reliability engineers must write proper specifications, test the equipment
of different vendors, and document problems. These specifications should include, as a
minimum, vibration, alignment, and balancing criteria. Documenting historical data, so
engineers can write verifiable purchasing and installation specifications for new and rebuilt
equipment, is the basis of this proactive technique. Performance testing is then conducted (1) in
3-34 February 2000

the factory prior to shipment, (2) as the equipment is installed prior to acceptance, and (3) to
establish a performance baseline as the equipment begins operation.
In addition, the use of PT&I for measuring equipment condition are not normally contained in
the procurement specifications. It is rare to see a banded-vibration criteria, a quantifiable
alignment/ balance specification, or a complex phase impedance for an electric motor.
3.4.2 Precision Rebuild and Installation

Equipment requires proper installation to control life-cycle costs and maximize reliability. Poor
installation often results in problems routinely faced by both maintenance personnel and
operators. Rotor balance and alignment, two common rework items, are often poorly performed
or neglected during initial installation. The adoption and enforcement of precision standards can
more than double the life of a machine. For example, the contract specification for leveling
equipment being installed should include a maximum acceptable slope of the base and the frame;
e.g., a maximum slope of 0.001 inch per foot. The specification also should include the type and
accuracy of the instrument used for measuring the slope; e.g., a 12-inch machinist’s level
graduated to 0.0002 inch per foot. After the criteria have been included in the contract
specifications, the installation should be checked to ensure that the mechanic has complied with
the specification.
3.4.2.1 Balance
Bearings are the machine components that support and transfer the forces from the rotating
element to the machine frame. This results in the perception that bearings are inherently a
reliability problem due to the fact that only 10% to 20% of rolling element bearings achieve their
design life. One of the leading causes of premature rolling element bearing failure is parasitic
load due to excessive vibration caused by imbalance and misalignment. The resulting parasitic
loads result in increased dynamic loads on the bearings. The design formulas (SKF, 1973) used
to calculate theoretical rolling element bearing life are:
a. Ball Bearings
16,667 C
L10 Life Hours = ( ) X ( )3
RPM P
b. Roller Bearings
16,667 C 10
L10 Life Hours = ( ) X ( )9
RPM P
Where, L10 is the number of hours 90% of a group of bearings should attain or exceed under a
constant load (P) prior to fatigue failure; C is the bearing load which will result in a life of one
February 2000 3-35

million revolutions; and P is the actual bearing load, static and dynamic. C is obtained from a
bearing manufacturer’s catalogue and P is calculated during equipment design.
As shown, bearing life is inversely proportional to speed and more significantly, inversely
proportional to the third power of load for ball and to the 10/9 power for roller bearings.
3.4.2.2 Balance Calculations9

Precision balance of motor rotors, pump impellers, and fans is one of the most critical and cost
effective techniques for achieving increased bearing life and resultant equipment reliability. It is
not usually sufficient to simply perform a single plane balance of a rotor to a level of 0.10 in/sec
or 1.0 nor, is it sufficient to balance a rotor until it achieves low vibration levels. Precision
balance methods should also include the calculation of residual imbalance. The following
equation can be used to calculate residual imbalance:
Vr
Ur = xM
Ve
Where Ur is the amount of residual imbalance, Vr is the actual imbalance, Ve is the trial mass
imbalance, and M is the trial mass. This equation can be expressed as follows:
Residual Imbalance = (Trial Wt.)(Trial Wt. Radius)(Amplitude After Balance)

(Trial Wt. Effect)
Permissible imbalance is related to equipment type and rotor mass. In general, the greater the
rotor mass, the greater the permissible imbalance. The following equation can be used to
determine the relationship between permissible residual imbalance (Uper) based on the rotor mass
(m) and a required or target permissible imbalance (eper):
U per
e per =
m
The relationship between speed and imbalance can be expressed by the following equation:
e per x ω = a constant
where, ω is the rotor angular velocity at maximum operating speed.
Table 3–3 below contains the ISO1940/1-1986 balance quality grades for various groups of
representative rigid rotors.
9
The following equations and discussion of permissible imbalance is based on ISO 1940/1, Mechanical vibration—
Balance quality requirements of rigid rotors. 1986
3-36 February 2000

Product of
Balance The
Quality Relationship Rotor Types—General Examples
Grade (eper x ) 1,2
mm/s
G4,000 4,000 Crankshaft/drives3 of rigidly mounted slow marine diesel

engines with uneven number of cylinders4
G1,600 1,600 Crankshaft/drives of rigidly mounted large two-cycle

engines
Crankshaft/drives of rigidly mounted large four-cycle
engines
G630 630
Crankshaft/drives of elastically mounted marine diesel
engines
G250 250 Crankshaft/drives of rigidly mounted fast four cylinder

diesel engines4
Crankshaft/drives of rigidly mounted fast diesel engines
G100 100 with six or more cylinders4
Complete engines (gas or diesel) for cars, trucks, and
locomotives5
Car wheels, wheel rims, wheel sets, drive shafts
Crankshaft/drives of elastically mounted fast four-cycle
G40 40 engines (gas or diesel) with six or more cylinders
Crankshaft/drives of engines of cars, trucks, and
locomotives
Drive shafts (propeller shafts, cardan shafts) with special
requirements
Parts of crushing machines
G16 16 Parts of agricultural machinery
Individual components of engines (gas or diesel) for cars,
trucks and locomotives
Crankshaft/drives of engines with six or more cylinders
under special requirements
Parts of process plant machines
Marine main turbine gears (merchant service)
G6.3 6.3 Centrifuge drums
Paper machinery rolls: print rolls
Fans
Assembled aircraft gas turbine rotors
February 2000 3-37

Product of
Balance The
Quality Relationship Rotor Types—General Examples
Grade (eper x ) 1,2
mm/s
Flywheels
Pump impellers
Machine-tool and general machinery parts
Medium and large electric armatures (of electric motors
having at least 80 mm shaft height) without special
requirements
Small electric armatures, often mass produced, in
vibration insensitive applications and/or with vibration
isolating mountings
Individual components of engines under special
requirements
Gas and steam turbines, including marine turbines
(merchant service)
Rigid turbo-generator rotors
Computer memory drums and discs
Turbo-compressors
G2.5 2.5 Machine-tool drives
Medium and large electric armatures with special
requirements
Small electric armatures not qualifying for one or both of
the conditions specified for small electric armatures of
balance quality grade G6.3
Turbine-driven pumps
Tape recorder and phonograph (gramophone) drives
G1 1 Grinding-machines drives
Small electric armatures with special requirements
G0.4 0.4 Spindles, disc, and armatures of precision grinders

Gyroscopes
Table 3–3. Balance Quality Grades for Various Groups of Representative Rigid Rotors (ISO
1940/1-1986)
Notes:
1. ω=2πn/60≈n/10, if n is measured in revolutions per minute and ω is in radians per
second
2. For allocating the permissible residual unbalance to correction planes.
3. A crankshaft/drive is an assembly which, includes a crankshaft, flywheel, clutch,
pulley, vibration damper, rotating portion of connecting rod, etc.
3-38 February 2000

4. For the purposes of this part of ISO 1940, slow diesel engines are those with a piston
velocity of less than 9 m/s; fast diesel engines are those with a piston velocity of
greater than 9 m/s.
5. n complete engines, the rotor mass comprises the sum of all masses belonging to the
crankshaft/drive described in note 3 above.
3.4.2.3 Effect of Imbalance

As discussed earlier, imbalance forces make a major contribution to decreased bearing life. For
example, consider a rotor turning at 3600 RPM with 1 oz. of unbalance on a 12" radius.
Calculate the amount of centrifugal force due to imbalance as shown below, where:
mr(2πf )2
F = mA = mr ω 2 = = 0.102 mrf 2
g
F = Force
m = imbalance (lbs)
r = radius of imbalance (in)
f = rotational speed (Hz)
g = 386.4 in/sec2
Substitute 1 oz. (1/16 lb.), 12", 3600 RPM (60 Hz):
1
F = 0.102 x ( ) x (12) x (60 )2 = 275 lbs.
16
Thus, 1 oz. of imbalance on a 12" radius at 3600 RPM creates an effective centrifugal force of
275 lbs. Now calculate the effect of this weight on bearing life. Suppose that the bearings were
designed to support a 1000 lb. rotor. The calculated bearing life is less than 50% of the design
life as shown below.
1000 3
Actual L 10 Life = (Design L 10 Life) x ( )
1000 + 275
= 0.48 Design L 10 Life
3.4.2.4 Alignment
The forces of vibration from misalignment also cause gradual deterioration of seals, couplings,
drive windings, and other rotating elements where close tolerances exist. The use of precision
equipment and methods, such as reverse dial and laser systems to bring alignment tolerances
within precision standards, is recommended. Contrary to popular belief, both laser alignment
and reverse dial indicator equipment offer equal levels of precision; however, laser alignment is
considerably easier and quicker to learn and use. Recommended specifications for precision
alignment are provided in Table 3–4.
February 2000 3-39

Tolerance
Maximum Angularity
Coupling Type Horizontal & Vertical
Speed (RPM) (Inch/10 inch of
Parallel Offset (IN.)
Coupling Dia.)
600 0.005 0.010
900 0.0053 0.007
1200 0.0025 0.005
Short Coupling
1800 0.002 0.003
3600 0.001 0.002
7200 0.0005 0.001
600 0.005 N/A
Coupling with 900 0.0018 N/A
Spacer 1,200 0.0012 N/A
(Meåsurement
is per inch of 1,800 0.0009 N/A
spacer length) 3,600 0.0006 N/A
7,200 0.00015 N/A
Table 3–4. Recommended Coupled Alignment Tolerances (General Motors, 1993)
In addition to the alignment specifications, Table 3–5 contains the following additional tolerance
recommendations.
Parameter Tolerance
Soft Foot 0.002" max
Foot Centerline Deformation (No load to full load) 0.001" max
Single Steel Base Plate Thickness 1.0" min
Foot Movement Caused by Pipe Flange Tightening 0.002" max
Total Shim Pack 5
Minimum Shim Pack Size 0.125" min
Axial Shaft Play 0.125" max
Table 3–5. Alignment Related Tolerances (General Motors, 1993)
3-40 February 2000

3.4.2.5 Alignment Effects

Based on data from a petrochemical industry survey, precision alignment practices achieve:
• Average bearing life increases by a factor of 8.0.
• Maintenance costs decrease by 7%.
• Machinery availability increases by 12%.
Table 3–6 and Figure 3–2 provide limitations and effect of misalignment on rolling element
bearings, respectively. The maximum acceptable misalignment is based on experience data in
bearing manufacturers’ catalogs.
Misalignment Angle
Bearing Type
Minutes Radians
Cylindrical Roller 3–4 0.001
Tapered Roller 3–4 0.001
Spherical Roller 30 0.0087
Deep Groove Ball 12–16 0.0035–0.0047
Table 3–6. Limitations on Rolling Bearing Misalignment (Harris,1984)
February 2000 3-41

160
140
120
100
90
80
Percent of Standard Life
70
60
50
40
30
20
5 10 20
Misalignment (min.)
Figure 3 – 2. Effects of Misalignment on Roller Bearings
3-42 February 2000

3.4.3 Failed-Part Analysis

This proactive process involves visually inspecting failed parts after their removal to identify the
root causes of their failures. More detailed technical analysis may be conducted when necessary
to determine the root cause of a failure.
Bearings are generally the weakest equipment components. Only 10 to 20 percent of bearings
achieve their design life. The root causes of bearing failures may relate to improper installation,
poor lubrication practices, excessive balance and alignment tolerances, or poor storage and
handling techniques. Failed-bearing analysis provides methods to categorize defects such as
scoring, color, fretting, and pitting and to relate these findings to the most probable cause of
failure.
Over half of all bearing problems result from contamination or improper installation. While
indicators of contamination normally appear on the internal surfaces of bearings, indicators of
installation problems generally are evident on both internal and external surfaces.
3.4.4 Root-Cause Failure Analysis (RCFA

In some cases, plant equipment fails repeatedly, and the failures are accepted as a normal
idiosyncrasy of that equipment. Recurring problems such as short bearing life, frequent seal
fracture, and structural cracking are symptoms of more severe problems. However, maintenance
personnel often fix only the symptomatic problems and continue with the frequent repairs.
Repeated failures result in high costs for parts and labor and in decreased customer goodwill and
mission support reliability. Further, unreliable equipment may pose a continuing personnel
safety hazard.
While a PT&I program can identify most equipment faults at such an early stage that they never
lead to an equipment failure, the program often does not include discovering the underlying
reason for the faults. For example, a bearing may fail repeatedly because of excessive bearing
loads caused by an underlying misalignment problem. PT&I would most likely predict a bearing
failure and thus allow the bearing to be replaced before it fails, but if no one recognizes the
misalignment and eliminates it, conditions causing the failure will remain and failures will recur
and continue to require unnecessary corrective work and downtime.
RCFA proactively seeks the fundamental causes that lead to facility and equipment failure. Its
goals are to:
• Find the cause of a problem quickly, efficiently, and economically.
• Correct the cause of the problem, not just its effect.
• Provide information that can help prevent the problem from recurring.
• Instill a mentality of “fix forever.”
February 2000 3-43

3.4.5 Reliability Engineering

In combination with other proactive techniques, reliability engineering involves the redesign,
modification, or improvement of components or their replacement by superior components.
Sometimes a complete redesign of the component is required. In other cases, upgrading the type
of component metal or adding a sealant is all that is required. Progressive maintenance
organizations include a reliability engineer assigned this responsibility on either a full or part
time basis depending on the size of the facility.
3.4.6 Reliability Calculations

a. Mean Time Between Failure (MTBF)
MTBF should be calculated from data collected from machinery history information stored in the
Computerized Maintenance Management Software. Other sources of MTBF data are operator
logs, parts usage, and contractor records. Reliability can be expressed by the following
reliability function:
R(t) = 1 - F(t)
where F(t) is the probability the system will fail by time t. F(t) is basically the failure distribution
function, or the “unreliability” function. If the random variable t has a density function of f(t),
then the expression for reliability is:
R(t) = 1 - F(t) = f(t)dt
Assuming that the time to failure is described by an exponential density function, then
f(x) = 1/L(e-t/L)
where L is the mean life, t is the time period of interest and e is the natural logarithm base
(2.7183...). The reliability at time t is:
R(t) = 1/L(e-t/L) = e-t/L
Mean life (L) is the arithmetic average of the lifetimes of all items considered. The mean life (L)
for the exponential function is equivalent to mean time between failures (MTBF).
R(t) = e-t/M = e-F/t
Where, F is the instantaneous failure rate and M is the MTBF. If an item has a constant failure
rate, the reliability of that item at its mean life is approximately 0.37. In other words, there is a
37% probability that a system will survive its mean life without failure. Mean life and failure
rates are related by
Fr = 1/L
3-44 February 2000

b. Failure Rate
The rate at which failures occur in a specified time interval is called the failure rate
during that interval. The failure rate (Fr) is expressed as:
Fr = No. of failures/Total operating hours
Example:
Unit Failed at time (operating hours)
1 75
2 125
3 130
4 325
5 525
All five units operated for 525 hours following failure for a total of 2,625 hours. In addition Unit
1 experienced failure at 75 hours, Unit 2 at 125 hours, Unit 3 at 130 hours, Unit 4 at 325 hours,
and Unit 5 at 525 hours.
This results in a total operating hours of:
2,625 Total operating hours after failure.

75 Unit 1 operating hours before failure.
3,805 Total operating hours.
Thus the failure rate (Fr) is the reciprocal.
Fr= 5/3805= .001314 failures/hr.
Assuming an exponential distribution, the system mean-life or MTBF is:
MTBF = 1/Fr = 1/.001314 = 761 hours
When assuming the negative exponential distribution, the failure rate is assumed to be relatively
constant during normal system operation if the system design is mature. That is, the system is
operating beyond the infant mortality period of decreasing failure rate and either before the wear
out region of increasing failure rate, or as in the majority of cases a period of increasing failure
rate does not exist.
February 2000 3-45

c. Reliability Component Relationships
1. Series networks
In a series network each component is a single point of failure. For example, there is
normally only one labeler for each packaging line. If the labeler fails, the line stops.
Reliability (R) = (RA)(RB)(RC)
If a series configuration is expected to operate for a specified time period, its overall reliability
can be derived.
RS = e-(l +l +...+l )t
2. Parallel networks
In a parallel network, multiple redundant equipment exists. For example, parallel packaging
lines and/or redundant chilled water pumps.
Reliability (R) = RA + RB - (RA)(RB) 2 component network
(R) = 1 - (1-RA)(1-RB)(1-RC) 3 component network
(R) = 1 - (1-R)n n identical components
3. Series-parallel networks
Figure 3–3 provides examples of how to calculate network reliability for series and parallel
components within a system. As with electrical circuits, analyze the parallel portions to create
an equivalent and then complete the analysis by combining all components and equivalents
serially.
d. Related Reliability Factors
1. Availability (A)
(a) Inherent Availability (Ai)
(1) The probability that a system or equipment, when used under stated
conditions in an ideal support environment, will operate satisfactorily at
any point in time as required.
3-46 February 2000

Figure 3 – 3. Determining Network Reliability
(2) Excludes preventive or scheduled maintenance actions, logistics delay

time and administrative delay time.
(b) Achieved Availability (Aa)
conditions in an ideal support environment, will operate satisfactorily at
any point in time.
(2) Preventive (scheduled) maintenance is included.
(3) Excludes logistics delay time and administrative delay time.
c. Operational Availability (Ao)
conditions in an actual operational environment, will operate satisfactorily
when called upon.
(2) Includes active maintenance time, logistics delay time and administrative
delay time.
February 2000 3-47

e. `Weibull Distributions
The Weibull distribution is generally used to determine probability of the failure due to fatigue.
The original work was conducted in 1933 and titled, A Statistical Theory of the Strength of
Materials. While the original work was not directly related to bearings, it was modified in 1947
by Lundberg and Palmgren (Lundberg, 1947) to account for the effectiveness of the lubricant
and the fact not all cracks propagate to the bearing surface.
The importance of the Weibull distribution is that the fatigue behavior of a group of identical
bearings can be assessed and changes in the failure distribution used to identify the introduction
of new sources of failure, i.e., changes in operating condition, lubrication/installation practices,
etc.
The Weibull distribution is:
k
F(t) = 1 - e-(t/T)
where, F(t) is the failure probability, T is the point in time at which 63.2% of the bearings have
failed, and k is corresponds to the gradient. The value of k for bearings is 10/9 for ball bearings
and 27/20 for roller bearings. In addition, F(t) for bearings should be in the range of 0.07-0.60.
In order to use the Weibull distribution to determine failure probability for bearings, it is
necessary to have a minimum of ten (10) identical bearings operating under as close to identical
conditions as possible.
3.4.7 Rebuild Certification/Verification

When new or rebuilt equipment is installed, it is essential to verify that it is operating properly.
To avoid unsatisfactory operation and early failure, the equipment should be tested against
formal certification and verification standards.
3.4.8 Age Exploration

Age Exploration (AE) is a key element in establishing an RCM program. AE provides a
methodology to vary key aspects of the maintenance program in order to optimize the process.
For example, a vendor recommends open and inspection of a chiller at certain intervals. During
the open and inspect, the technician notes the condition of various components of the chiller.
The condition evaluation sheet is then correlated with performance data from the Energy
Management and Control System (EMCS), vibration data, and oil analysis data. As a result of
this analysis, the decision is made to change the interval of the open and inspect until monitored
conditions indicate degradation has occurred.
The AE process examines the applicability of all maintenance tasks in terms of the following:
a. Technical Content—The technical content of the tasks are reviewed to ensure all
3-48 February 2000

identified failure modes are addressed and that the existing maintenance tasks
produce the desired amount of reliability.
b. Performance Interval—During the AE process, the task performance interval is

continually adjusted until the rate at which resistance to failure declines is
determined. For example, identical motors with significantly different amplitudes
of vibration could result in different monitoring intervals.
c. Task Grouping—Tasks with similar periodicity are grouped together to improve

the amount of time spent on the job site and minimize outages.
3.4.9 Recurrence Control

This section provides a systematic approach using technical analysis of hardware and/or material
failures for dealing with repetitive failures. Events warranting RCFA are an end result or
product of implementing the following methodology.
Repetitive failures are defined as the recurring inability of a system, subsystem, structure or
component to perform the required function, i.e.:
• Repeated failure of an individual piece of eqquipment;
• Repeat failures of various equipment within a system or subsystem; or
• Failures of the same or similar components in several different systems.
The following items should be considered when analyzing failures:
• Systematically address the failures of systems, structures and components
• Provide a means to evaluate failures
• Contribute to long term improvements in plant operation and safety
• Efficiently allocate resources to the investigation and correction of failures that

are most critical
The following process for conducting an analysis of repetitive failures is provided:
• Monitor plant or equipment performance
• Identify repetitive system/component failures using a form similar to Figure 3 – 4
• Establish priorities for solution and allocation of resources
• Assign problems for analysis
February 2000 3-49

• Analyze problems/determine root cause
• Recommend corrective action
• Select corrective action
• Implement selected corrective actions
• Evaluate results of implemented corrective actions
In addition to developing a process for evaluating repetitive failures, a systematic approach

similar to the following should be established:
a. Monitor performance and identify failures by reviewing Trouble Calls and machinery
history contained in the CMMS and PT&I databases.
1. Extend PT&I monitoring activities as widely as possible across the Facility

consistent with the concepts of RCM.
2. Encompass the Facility's critical components as identified by RCM. Include

safety-related systems and components and include systems and components
that support safety systems.
b. Monitor the performance of both systems and components because;
1. System monitoring will identify potential loss of equipment due to aging,

corrosion, wear, design or operational problems.
2. Component monitoring will identify possible generic failure problems that may
affect multiple plant systems.
c. Sources of repetitive failure data are:
1. Number of maintenance man-hours by system or component
2. Number of maintenance work orders by system or component
3. Maintenance backlog (by system)
4. Control instruments out of service
5. Achievement of maintenance performance goals. i.e,
• Safety system unavailability
3-50 February 2000

• Number of inadvertent safety system actuations
• Number of unplanned facility shutdowns
• Lost mission or production time
• Forced outage rate
• Number of Incident Reports
d. Establish priorities by performing the following:
1. Ranking identified problems using Pareto Analysis.
2. Providing a framework for the allocation of resources.
3. Focusing attention on problems identified as the most important to the

achievement of the Facility's operational and safety goals.
4. Considering the following in the ranking process:
• Overall plant performance goals
• Reliability Centered Maintenance (RCM) studies
• Plant Safety Analyses/Technical Specifications
• Costs in hours, dollars, exposure or lost production due to recurring

failures
e. Assign problems for analysis based on the following:
1. Match the problems to available resources (staffing and money).
2. Determine the complexity of the problem.
• Provide a clear definition of the problem
• Provide the expected improvement in performance (standard by which to

measure possible solutions)
3. Select the size and composition of the problem solving team.
4. Provide a schedule which allows for effective feedback and timely completion
of the task.
February 2000 3-51

f. Analyze the problem and recommend corrective action based on the following:
1. Collect all relevant data (CMMS, PT&I, etc.).

2. Analyze the component and/or system failure.
3. Determine the root cause of failure.
4. Develop a list of potential corrective actions.
g. Select corrective actions for implementation
1. Evaluate and prioritize the possible corrective actions.

2. Factors to consider are:
• Achievement of the improvement goals

• Ease of implementation
• Resources required (labor, cost, schedule) to implement the corrective
action
• Time necessary to implement the corrective action
• Design bases and regulatory requirements
h. Implement selected corrective actions by performing the following:
1. Assign corrective actions to individuals, departments or teams for

implementation.
2. Establish schedules and milestones.
3. Review schedule periodically to ensure adequate progress is being made.
4. Adjust schedule and/or resources if necessary.
i. Monitor impact of implemented corrective actions by performing the following:
1. Monitor system performance (PT&I and process data should be used).

2. Determine whether the improvement goals have been met.
3-52 February 2000

Failure Analysis Form

Reliability Centered Maintenance
Equipment Identification: Unit #: Equip. Type:
Ser.#: Location:
Name of Person(s) Responding:
Time the Equipment Failure: Date: Time:
Time Equipment Returned To Service: Date: Time:
Brief Description of Failure:
Probable Cause of Failure:
Corrective Action Taken:
Parts Replaced:
Previous Failures (review CMMS):
Date Last PM was Performed: Associated WO #:
Direct Cost Data: In-house Contract Subtotal
Labor: $ $ $
Material: $ $ $
Total Cost: $
Failure Analysis Report completed by: Date:
Figure 3 – 4. Failure Analysis Form
February 2000 3-53

3.4.10 Facilities Condition Assessment

The Facilities Condition Assessment (FCA) process should be considered as a continuous
process and not as a series of discrete independent events. This can be accomplished by using
the existing CMMS and PT&I databases, customer inputs, and Facility or Building Manager
periodic inspections.
Individual system reliability and M&O costs, number of Trouble Calls normalized to operating
hours and plotted over service life can be tracked by the CMMS. Equipment condition relative
to other similar equipment can be tracked by reviewing the PT&I data and statistically
determining the selected component relationships with respect to the mean and standard
deviation. For example, a facility has X number of centrifugal water pumps of similar but not
identical design in the range of 15–25 Hp. All of the pumps receive quarterly vibration
monitoring, which includes a visual inspection, and annual insulation resistance check or motor
circuit test. The insulation resistance checks are temperature corrected so they may be trended.
In addition, where possible, flow and/or discharge pressure are noted during the vibration
surveys and trended.
Each pump/motor combination is assigned a value of 1, 4, or 9 based on its relationship with the
mean. For example, as illustrated in Figure 3-5, 50% of the equipment would be in better
condition than the mean, 68.3% better than the mean plus 1 σ (sigma), 95.4% better than the
mean plus two σ (sigma), and 99.7% better than the mean plus three σ (sigma).
Mean Mean + 1 sigma
Mean + 2 sigma
Mean + 3 sigma
f(x)
Figure 3 – 5. Mean and Standard Deviation
3-54 February 2000

For example, if the vibration amplitude is below mean + 1σ (sigma) the unit would be scored as
1, below mean + 2σ it would be scored as 4, and above mean + 2σ it would be scored as a 9.
Table 3–7 provides an example.
For more complex equipment and/or for equipment where more PT&I technologies are used, the
table would be expanded. In addition, similar Tables should be prepared for Trouble
Calls/Repairs normalized to operating hours, M&O costs, PT&I alarms normalized to operating
hours, Availability, etc. The sum of all the Tables will result in a rank ordering of the equipment
in terms of condition. This approach will address the functional condition in terms of availability
and cost to maintain function.
Pump/Motor Vibration Value Resistance Value Total

1 1 1 2
2 1 1 2
3 4 4 8
4 4 1 5
5 9 1 10
Table 3–7. Equipment Condition Classification Based on PT&I Data
Structures can be treated in a similar manner. In these cases, a periodic inspection by the Facility
Manager of the common spaces, hallways, equipment rooms, roofs, and grounds combined with
PT&I data from thermography, airborne ultrasonics, etc.
While the preceding technique is appropriate for equipment and structures, private spaces, such
as offices, should be handled by the user. A form similar to Figure 3-6 can be used to obtain user
input and address more subjective issues related to morale and appearance.
The office user should fill out a form similar to Figure 3 – 6 on an annual or semiannual basis to
identify problems with the space. This information is then used to generate a work order which,
can be prioritized and tracked.
February 2000 3-55

OFFICE CONDITION FORM
LOCATION: Facility No. Room No. DATE:
NO CHANGE SINCE LAST INSPECTION
Inspected By: Phone No.

SKETCH OFFICE HERE
DESK
Please indicate the following on the above office outline:
Ceiling Tiles: No. Missing _____ Windows: Mark Locations

No. Broken _____ Cracked or Broken
No. Stained _____ Leaks
Electrical Outlets and Switches: Mark Location Doors: Mark Locations

Missing _____ Handle, Hinges or Lock
Cracked _____
Walls: Paint Lighting: Good Poor

Cracks
Ventilation: Airflow _____ Air Quality _____ Temperature Control _____
Carpet: Stains _____ Rips _____ Frayed _____
Resilient Titles: No. Cracked _____ No. Stained: _____
Overall Appearance: Good Fair Poor
Comments:____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
Work Control No.
Date Received
Date Cleared
Signature
Figure 3-6. Office Assessment Form
3-56 February 2000

Chapter 4— Predictive Testing & Inspection (PT&I)

Technologies
4.1 Introduction
This chapter describes each of the primary PT&I technologies in terms of its purpose,
techniques, application, effect, equipment required, operators, training available, and cost.
A variety of methods are used to assess the condition of systems/equipment to determine the
most effective time to schedule and perform maintenance. The information below provides an
introduction on how the technologies are currently utilized and their respective benefits. These
technologies include both intrusive and non-intrusive methods as well as the use of process
parameters to determine overall equipment condition. The data acquired permits an assessment
of system/equipment performance degradation from the as designed and/or required condition.
In addition, these techniques should also be used to assess the quality of new and rebuilt
equipment installations and operational checks. The approaches covered include:
• Vibration Monitoring & Analysis

• Infrared Thermography
• Ultrasonic Noise Detection
• Lubricant and Wear Particle Analysis
• Electrical Condition Monitoring
• Non-Destructive Testing
Figure 4–1 provides information on the applicability of the technologies to various facility and
production components. Data should be correlated as described in Section 3 and Appendix F.
4.1.1 Alerts and Alarms

Alerts and alarms are set to meet specific user requirements. Common methods used to
determine alert and alarm values are:
a. Arbitrary Value—Set an arbitrary value for change from a baseline value. In this
situation an increase in the reading by a predetermined amount over the initial
reading is used to determine maintenance requirements. This approach was widely
used by the U.S. Navy submarine force until the middle 1980s at which time it was
abandoned in favor of a more statistical approach as described below.
b. Alert Value—Set an alert value to indicate a statistically significant deviation

(usually 2 sigma) from the mean as a warning or alert level. An alarm value is
established at 3 sigma. This approach should allow sufficient time between the
alert and alarm levels and failure in order to schedule repairs.
February 2000 4-57

HEAVY EQUIPMENT/CRANES
ELECTRICAL SYSTEMS
APPLICATIONS
DIESEL GENERATIORS
HEAT EXCHANGERS
CIRCUIT BREAKERS
ELECTRIC MOTORS
TRANSFORMERS
TANKS, PIPING
CONDENSERS
VALVES
PUMPS
TECHNOLOGIES
VIBRATION MONITORING/ ANALYSIS l l l l
LUBRICANT, FUEL ANALYSIS l l l l l
WEAR PARTICLE ANALYSIS l l l l
BEARING, TEMPERATURE/ANALYSIS l l l l
PERFORMANCE MONITORING l l l l l l
ULTRASONIC NOISE DETECTION l l l l l l l l
ULTRASONIC FLOW l l l l
INFRARED THERMOGRAPHY l l l l l l l l l l
NON-DESTRUCTIVE TESTING
(THICKNESS) l l l
VISUAL INSPECTION l l l l l l l l l l l
INSULATION RESISTANCE l l l l l
MOTOR CURRENT SIGNATURE
ANALYSIS l
MOTOR CIRCUIT ANALYSIS l l l
POLARIZATION INDEX l l l
ELECTRICAL MONITORING l l
Figure 4-1. PT&I Applications
c. Failure Analysis—Refine the alert and alarm values by performing analysis of the
failed parts and then correlating the as-found condition to the PT&I data. This is
why it is important to document trends, the values at which failures occur, and the
operating environment for future reference. Changing the alert and alarm values is
the mechanism to fine tune the condition monitoring process and should be based
on the best information available.
4-58 February 2000

4.2 Vibration Monitoring & Analysis

Analysis of system and equipment vibration levels is one of the most commonly used PT&I
techniques. Vibration monitoring helps determine the condition of rotating equipment and
structural stability in a system. In addition, vibration monitoring aids in the identification and
localization of airborne noise sources.
Machinery and system vibration is the periodic motion of a body about its equilibrium position.
For example, imagine driving a car at a constant speed through a series of potholes with each one
being larger than the last. The shock and resulting vibration increases with each encounter until
at some point it destroys the suspension, wheel, or tire. This analogy depicts what occurs as
bearing and gear defects begin and then increase in size with each additional impact.
4.2.1 Applications and Techniques

Applicable to all rotating equipment; e.g., motors, pumps, turbines, compressors, engines,
bearings, gearboxes, agitators, fans, blowers, shafts, etc. In addition, modern data loggers
support resonance testing, equipment balancing, and airborne noise measurements.
4.2.1.1 Conditions Monitored

Wear, imbalance, misalignment, mechanical looseness, bearing damage, belt flaws, sheave and
pulley flaws, gear damage, flow turbulence, cavitation, structural resonance, fatigue, etc.
4.2.1.2 Detection Interval

Narrowband vibration analysis can provide several weeks or months of warning of impending
failure. Base the time interval on the experience of the analyst and the type, quantity, and quality
of data collected.
4.2.1.3 Accuracy
Studies by the U.S. Navy have found probabilities of detection as high as 0.92 and as low as
0.76. The corresponding false alarm rate was found to be 0.08. Selecting the appropriate
monitoring intervals and alarm criteria optimizes probability of detection and false alarm rates.
4.2.1.4 Overall Vibration

Overall measurement is the sum of all vibration energy produced across a filtered bandwidth.
Overall measurement provides an easy indicator of the major sources of vibration but does not
provide a complete picture of a systems condition. A modern maintenance program will not
depend solely on an overall measurement approach to vibration analysis.
4.2.1.5 Spectrum Analysis and Waveform Analysis

Spectrum analysis of the frequency domain is the most commonly employed analysis method for
machinery diagnostics. The spectrum analysis is used to identify the majority of all rotating
February 2000 4-59

equipment failures (due to mechanical degradation) prior to failure. Waveform analysis, or time
domain analysis, is another extremely valuable analytical tool. While not employed as regularly
as spectrum analysis, the waveform often aids the analyst in a more correct diagnosis of the
machine problem.
4.2.1.6 Torsional Vibration

Often utilized to detect the vibration associated with gear vibration and shaft torque. It proves
most helpful in situations where, due to transmission path attenuation, the casing vibration signal
has a signal-to-noise ratio insufficient to detect the problem. Torsional vibration measurement is
especially effective in situations where unsteady forces excite the resonance of the structure or
housing. Torque is measured by using pairs of matched sensors spaced at an interval. This is
done to take advantage of the phase difference in the signals due to shaft twisting, which is a
function of shaft stiffness and load.
4.2.1.7 Multi-Channel Vibration Analysis

Offers several extremely powerful methods for machinery analysis such as force-response
analysis, cross-coupling phase analysis, analysis of resonance mode characteristics, and multi-
plane balancing. Additionally, coherence functions offered by multi-channel analyzers allow for
checking the quality and linearity of data collected with typical data loggers.
4.2.1.8 Shock Pulse Analysis

Sometimes used to detect impacts caused by contact between the surfaces of the ball or roller and
the raceway during rotation of antifriction bearings. The magnitude of these pulses depends on
the surface condition and the angular velocity of the bearing (RPM and diameter). Spike energy
is similar in theory to shock pulse.
4.2.1.9 Vibration Sensor Mounting

The use of a low mass accelerometer (100mV/g) and a rare earth super magnet attached to an
accelerometer is the recommended approach to monitor most facilities machinery. In some
cases, the use of a permanently mounted accelerometer is required. The permanently mounted
accelerometer will provide the best signal transfer but it is not usually the most cost effective
method. The use of a magnet mounted accelerometer, and a smooth mounting surface has been
proven by the U.S. Navy to provide a usable upper frequency limit of 5 kHz. By utilizing special
purpose accelerometers and a couplant between the accelerometer, magnet, and mounting disc,
accurate measurements to 20 kHz are possible. Figure 7–1 provides a recommended frequency
response curve for a properly mounted accelerometer.
The practice of using a hand-held probe severely limits the upper vibration frequency that can be
accurately measured. When combined with the failure to mark the measurement points and the
use of different individuals to collect data, the repeatability of the vibration data analysis
significantly decreases.
4-60 February 2000

SOUND DISC DIAGRAM
The discs are to be manufactured from a magnetic stainless steel such as alloy 410 or
416.
One (1) inch

diameter 3/8 inch
thick
TOP VIEW SIDE VIEW

Surface finish to be 32-125 Faces to be parallel within one
micro-inches RMS. (1) degree. Sharp edges to be
removed from corners.
Figure 4-2. Sound Disc Diagram
Identify each monitoring point and epoxy magnetic corrosion resistant steel discs (sound discs)
at every location. Sound discs should be a minimum of one inch in diameter and 3/16 to 3/8 inch
thick. The discs can be purchased10 with prices ranging from $0.25 to $6.00 each or can be
manufactured by fly cut from 1" alloy 410 or 416 bar stock. Figure 4–2 provides a dimensional
drawing of a sound disc. The surface finish should be a minimum 63 micro-inch. Good
frequency response is more related to placing the magnet on a clean surface with a lubricant
between the magnet and the disk than a highly polished surface. When using a stud to mount the
accelerometer directly to the disk or finished surface, the minimum surface finish is 32 micro-
inch. The disk or surface face must be level to prevent the magnet from rocking. Surface must
be level within 1 degree or .001 inch.
Use a tested epoxy such as Hysol Gray Epoxy Patch (available from Structural Adhesives) or
Loctite Depend 330 to adhere the sound disc to the equipment. Prepare the surface for the epoxy
by grinding or spot facing with a portable milling machine and wiping down with a solvent. If
the portable milling machine is used to spot face the surface, ensure that the face diameter is
¼ inch in diameter larger than the disc diameter. The use of superglue type adhesives is not
recommended, the sound discs do not adhere well when this type adhesive is used. Wielding the
discs to the machine is also an option, but it is not recommended because of possible damage to
the machine and distorting of the disc surface.
As an alternative, the monitoring locations may simply be the spot faced area machined on the
equipment surface. The same conditions identified for the sound disc apply to the machined
surface.
10
Michoud Assembly Facility gets inexpensive sound discs from a washer supplier. They simply special order the
washers without holes. Supplier is Phoenix Specialty Mfg.. Co., PO Box 418, Bamberg, SC 29003 Phone 800-845-
2813, fax 803-245-5734. Be sure to specify "washers with no holes."
February 2000 4-61

The sound disc or machined surface should be marked (using a label or plate) "Vibration data
collection point - Do Not Paint"
4.2.2 Limitations
The effectiveness of vibration monitoring is dependent on sensor mounting and resolution, the
analyst’s knowledge and experience, machine complexity, and data collection techniques.
Complex, low speed (<120 RPM), variable speed, and reciprocating machinery are extremely
difficult to monitor effectively.
Additionally, single channel analysis cannot always accurately determine the source of the
vibration on complex machines.
4.2.3 Logistics
4.2.3.1 Equipment Required

Vibration analysis systems include micro-processor data collectors; vibration transducers,
equipment-mounted sound discs, and a host personal computer with software for analyzing
trends, establishing alert and alarm points, and assisting in diagnostics.
4.2.3.2 Operators
• Requires personnel who have the ability to understand the basics of vibration
theory and who have a basic knowledge of machinery and failure modes.
• Staffing requirements are site specific
4.2.3.3 Training Available

• Equipment vendors and independent companies provide training. See Appendix
C for training sources.
• The Vibration Institute has published certification guidelines for vibration
analysts. These guidelines are used by the various vibration equipment vendors
and independent trainers. Passing a written examination is required for
certification as a Level I, II, or III analyst.
4.2.3.4 Cost (1998)

$20,000 to $120,000 for narrowband systems, software, and introductory training. The high-
priced systems are for a basic multi-channel, installed system which can be expanded at a cost of
$500-$1,000 per additional sensor. Portable analyzers appropriate for use are approximately $25
– $32,000, which includes all hardware, software, and training.
4-62 February 2000

4.3 Infrared Thermography

Infrared Thermography (IRT) is the application of infrared detection instruments to identify
pictures of temperature differences (thermogram). The test instruments used are non-contact,
line-of-sight, thermal measurement and imaging systems. Because IRT is a non-contact
technique, it is especially attractive for identifying hot/cold spots in energized electrical
equipment, large surface areas such as boilers and building walls, and other areas where “stand
off” temperature measurement is necessary. Instruments that perform this function detect energy
in the short wave (3 to 5 microns) and long wave (8 to 15 microns) bands of the electromagnetic
spectrum. The short wave instrument is the best choice for facilities inspections due to the
varied inspections (electrical, mechanical, and structural) encountered. However, the short wave
instrument is more sensitive (than long wave) to solar reflections and the inspector will need to
be aware of this when performing outdoor inspections such as in substations and switchyards.
To be effective in facilities applications, the instruments must be portable, sensitive to within
0.2oC over a range of temperatures from -10oC to +300oC, and accurate within ±3%. In addition,
the instrument must be capable of storing an image of the thermogram for later use.
IRT inspections are identified as either qualitative or quantitative. The quantitative inspection is
interested in the accurate measurement of the temperature of the item of interest. To perform a
quantitative inspection requires detailed knowledge and understanding of the relationship of
temperature and radiant power, reflection, emittance, environmental factors, and the detection
instrument limitations. This knowledge and understanding must be applied in a methodical
fashion to properly control the imaging system and obtain highly accurate temperature
measurements. Quantitative inspections are rarely needed in facilities applications.
The qualitative inspection is interested in relative differences, hot and cold spots, and deviations
from normal or expected temperature ranges. The knowledge and understanding discussed
above is needed in order to perform a meaningful inspection. However, qualitative inspections
are significantly less time consuming because the thermographer is not concerned with highly
accurate temperature measurement. What the thermographer does obtain is highly accurate
temperature differences (∆ T) between like components. For example, a typical motor control
center will supply three-phase power, through a circuit breaker and controller, to a motor.
Current flow through the three-phase circuit should be uniform which means that the
components within the circuit should have similar temperatures, one to the other. Any uneven
heating, perhaps due to dirty or loose connections, would quickly be identified with the IRT
imaging system. Because the many variables that influence the quantitative inspection
(reflection, emittance, etc.) are the same between like components, the thermographer can
quickly focus on the temperature differences. The factors so important to a highly accurate
temperature measurement have very little influence on the temperature differences between like
components.
4.3.1 Applications
IRT can be utilized to identify degrading conditions in facilities electrical systems such as
transformers, motor control centers, switchgear, substations, switchyards, or power lines. In
mechanical systems, IRT can identify blocked flow conditions in heat exchanges, condensers,
February 2000 4-63

transformer cooling radiators, and pipes. It can also be used to verify fluid level in large
containers such as fuel storage tanks and identify insulation system condition in building walls
and roof or refractory in boilers and furnaces. Temperature monitoring, infrared thermography
in particular, is a reliable technique for finding the moisture-induced temperature effects that
characterize roof leaks and for determining the thermal efficiency of heat exchangers, boilers,
building envelopes, etc.
Deep-probe temperature analysis can detect buried pipe energy loss and leakage by examining
the temperature of the surrounding soil. This technique can be used to quantify energy losses
and their cost. IRT can also be used as a damage control tool to locate mishaps such as fires and
leaks. Unless requested otherwise, the thermographer will normally only provide an exception
report consisting of finds/faults.
In-service condition for electrical and mechanical systems can be assessed and work prioritized
based upon the temperature difference criteria (∆T) guideline. IRT criteria are provided in
Section 8.2.3.
4.3.2 Limitations
Thermography is limited to line of sight. The infrared camera has limited ability to see through
material. Most items that are usually considered transparent to the human eye, such as glass and
plastic, are opaque to the infrared camera. Errors can be introduced due to type of material,
material geometry, and by environmental factors such as solar loading and wind effects.
4.3.3 Logistics

• Equipment ranges from simple, contact devices such as thermometers and crayons
to full color imaging, computer-based systems that can store, recall, and print
thermal images.
• The deep-probe temperature technique requires temperature probes, analysis

software, and equipment to determine the location of piping systems.
4.3.3.2 Operators
• Operators and mechanics can perform temperature measurements and analysis
using contact-type devices with minimal training on how and where to take the
temperature readings.
• Because thermographic images are complex and difficult to measure and analyze,
training is required to obtain and interpret accurate and repeatable thermal data
and to interpret the data. With adequate training (Level I and Level II) and
certification, electrical/mechanical technicians and/or engineers can perform this
technique.
4-64 February 2000

• Maintenance personnel can apply deep-probe temperature monitoring after being

trained, although this service is often contracted.

• Training is available through infrared imaging system manufacturers and vendors.
• The American Society of Non-destructive Testing (ASNT) has established
guidelines for non-destructive testing (NDT) (Level I, II, or III) thermographer
certification (Appendix C). These guidelines, intended for use in non-destructive
testing, may be useful for thermography in PT&I if appropriately adjusted.
General background, work experience, thermographic experience, and
thermographic training are all considerations for certification. The
thermographer’s employer normally pays for any training and for making the
decision to certify the thermographer. The trainer provides course completion
certificates and recommends certification criteria, but the ultimate certification
decision is the employer’s.
4.3.3.4 Cost (1998)

• Noncontact infrared thermometers/scanners start at approximately $1,000. Full
color microprocessor imaging systems with data storage and print capability range
from approximately $15,000 to $60,000.
• Digital IR Still Camera technology which operates in the long wave band is
available at approximately 1/4th the cost of a cooled focal plane array camera and
provide a good entry level system.
• Average thermographic system rental is approximately $1,500 per week.
Operator training costs approximately $1,250 per week.
• Thermographic contractor services cost approximately $1,000 per day. Contract
services for deep-probe temperature analysis cost from $1,500 to $2,000 per day,
with $5,000 to $6,000 for the first day.
4.4 Ultrasonic Noise Detection

Ultrasonic noise detection devices operate in the frequency range of 20kHz–100kHz and
heterodyne the high frequency signal to the audible range. This allows the operator to be able to
hear changes in noise associated with leaks, corona discharges, and other high frequency events
such as bearing ring and housing resonant frequency excitation caused by insufficient lubrication
and minor defects.
4.4.1 Applications and Procedures

The following applications are applicable to all airborne ultrasonic devices.
February 2000 4-65

4.4.1.1 Gas Pressure and Vacuum Leaks

The most common application of the ultrasonic noise detector is examining in-service gas
systems for leaks. The detector is used in the non-contact mode and is effective for both pressure
and vacuum systems.
4.4.1.2 Heat Exchangers

Perform a general scan of the equipment with the sensitivity set to maximum in the fixed band
mode. As the search area is reduced, attach the rubber probe hood and reduce the equipment’s
sensitivity. Heat exchangers may be tested by either of the following methods:
a. Tone Generator—An ultrasonic source is placed inside the area to be tested (one
tone generator required for each 4,000 cubic feet of volume), the instrument is set
on scanning mode, log position, and fixed band. The tone generator can be
attached to an adapter at the end of a pipe to flood the pipe, heat exchanger shell,
or tube bundle with ultrasonic noises. A scan is then performed on the pipe or
tubes.
b. Differential Pressure Method— Gas pressure difference between the inspection

area and the scanning location. Perform a general scan of the area. When
checking the tubes, block the tubes, one at a time, and note differences in
readings. Mark any tubes suspected of leakage.
4.4.1.3 Boilers
Boiler casing surveys should be performed using the blowdown valves; the test equipment’s
fixed band, and the contact probe.
4.4.1.4 Steam Traps

Implementation of a steam trap monitoring program often has significant financial benefit. The
following method can be used to calculate potential cost avoidance. Initial steam trap11 surveys
in the petrochemical industry revealed that 34% of the steam traps inspected had failed, mostly in
the open position. Assuming a nominal steam pressure of 100 psig and the back pressure on the
trap is atmospheric, the following information can be used to calculate leak rates:
For facilities with a periodic steam trap monitoring program, the following distribution of
degradations were discovered during each survey:
• Five steam leaks (other than traps) per 150 traps
• Two leaking valves per 150 traps
• Twenty of the 150 traps leak

11
Yarway Technical Note STA-9
4-66 February 2000

The numbers above can be used to estimate the number of leaks for a facility and combined with
the data in Table 4 – 1 then used to approximate the total steam loss due to the steam leaks.
Leak Diameter Steam Loss per Month

(inches) (lbm)
1/64 3,300
1/32 6,650
1/16 13,300
1/8 52,200
1/4 209,000
1/2 833,000
Table 4 – 1. Estimated Steam Loss
Once the estimated amount of steam loss is calculated, the cost of producing or buying a pound
of steam should be calculated. The following should be considered when calculating the cost of
producing steam:
• Cost of fuel
• Operator cost
• Maintenance cost
• Chemical treatment cost
• Depreciation of steam plant
Steam traps should be monitored on the downstream side of the trap using the test equipment’s
contact mode, if applicable, in the 25kHz band and the log position. Each type of steam trap
produces a distinct sound as briefly described below. To gain experience with the difference in
the sound produced by steam and condensate, the operator should listen to a condensate and a
steam line.
a. Intermittent Traps—The operator will hear an opening and closing sound. The trap
normally fails in the open position, producing a continuous, rushing sound.
b. Inverted Bucket—A normal trap sounds as if it is floating; a failed trap sinks,

producing a continuous flow noise.
c. Thermostatic—Ultrasonic testing results of this type of trap vary. The noise

produced by these traps can be continuous or intermittent and will produce different
sounds accordingly.
d. Float and Thermostatic (Continuous Load)— Flow and noise associated with these
traps are usually modulated. Failed traps are normally cold and silent.
February 2000 4-67

e. Continuous Flow—This type of trap, when operating normally, produces the sound
of condensate flow only. If it has failed in the open position, a continuous flow sound
should be heard.
4.4.1.5 Corona Discharge

Corona is the polarization of air molecules due to electrical energy and is normally associated
with high voltage distribution systems. Corona is produced as a result of a poor connection or an
insulation problem. It produces noise in the ultrasonic region and ultraviolet light in the
electromagnetic spectrum (which is not normally detectable using thermography). Because the
inspection of high voltage systems is done at a safe distance, a parabolic hood is often attached to
the detector to direct and shield other noise sources.
4.4.1.5 Bearings
Airborne ultrasonics can be used to detect bearing problems but it is not the preferred method.
Vibration analysis is recommended.
4.4.2 Limitations
Airborne ultrasonics are subjective and dependent on perceived differences in noises. To
maximize the usefulness of this technology, care should be taken when setting test equipment
controls for frequency ranges, sensitivity, and scale. Additionally, the operator should be
cognizant of the fact that piping bends and the presence of moisture and solids may dissipate
and/or block the ultrasonic signal.
4.4.3 Logistics

Ultrasonic monitoring scanner for airborne sound or ultrasonic detector for contact mode through
metal rod.
4.4.3.2 Operators
Maintenance technicians and engineers.

Minimal training required with the exception of multi-channel Acoustic Valve Leak Detectors
(AVLDs).
4-68 February 2000

4.4.3.4 Cost (1998)

Scanners and accessories range from $1,000 to approximately $8,000. Complex acoustic valve
leak detection systems are approximately $100,000.
4.5 Lubricant and Wear Particle Analysis
4.5.1 Purpose
Lubricating oil analysis is performed for three reasons: to determine the machine mechanical
wear condition, to determine the lubricant condition, and to determine if the lubricant has
become contaminated. There are a wide variety of tests that will provide information regarding
one or more of these areas. The test used will depend on the test results sensitivity and accuracy,
the cost, and the machine construction and application. Note that the three areas are not
unrelated as changes in lubricant condition and contamination, if not corrected, will lead to
machine wear. Because of the important relationships, commercial analysis laboratories will
often group several tests in cost effective “packages” that provide information about all three
areas.
4.5.1.1 Machine Mechanical Wear Condition

The criteria for analyzing the lubricating oil to determine the machine’s condition is similar as
analyzing the vibration signature. That is, all machines with motors of a selected size (for
example, 7.5 HP or larger), critical machines, or high cost machines. Generally the routine
sampling and analysis periodicity will be the same as the vibration analysis periodicity (when
using a portable vibration data collector). For machines that have a condition history (a year or
more of data), this is typically performed quarterly or semi-annually.
4.5.1.2 Lubricant Condition

Lubricating oil is either discarded or reconditioned through filtering and/or replacing additives.
Analyzing the oil to determine the lubricant condition is therefore driven by costs. Small
reservoirs, usually one gallon or less, have the oil changed on an operating time basis. An
automobile is the most common example of time based lubricating oil maintenance. In this
example, the costs to replace the automobile oil (the replacement oil, labor to change the oil, and
disposal costs) are lower, through economies of scale and competition, than the cost to analyze
the oil (sample materials, labor to collect the sample and the analysis). Generally speaking,
discard the machine lubricating oil if it is cheaper than analyzing it. When making this decision,
keep in mind that the costs for sample materials and collection labor is a cost for each sample
collected and that each sample is used to perform many tests.
4.5.1.3 Lubricant Contamination

Lubricating oil can become contaminated due to the machine’s operating environment, improper
filling procedures, or through mixing different lubricants. The routine sampling and analysis
periodicity will be the same as discussed for machine condition. In addition, a periodic analysis
February 2000 4-69

following “topping off” or reconditioning the oil is performed. The root cause of any oil
contamination needs to be determined and eliminated in order to avoid machine damage.
Lubricating oil analysis is performed on in-service machines to monitor and trend emerging
conditions, confirm problems identified through other PT&I and observations, and to
troubleshoot known problems. As previously discussed, lubricating oil analysis is performed for
three reasons: to determine the machine mechanical wear condition, to determine the lubricant
condition, and to determine if the lubricant has become contaminated. Tests have been
developed to address indicators of these conditions and vary in cost dependent upon time and
materials needed to accomplish the testing. The tests selected for use in the PT&I program must
balance the need for understanding the lubrication condition and the cost of the testing.
4.5.2 Standard Analytical Tests

Lubricating oil and hydraulic fluid analysis should proceed from simple, subjective techniques
such as visual and odor examination through more sophisticated techniques. The more
sophisticated (and expensive) techniques should be used when conditions indicate the need for
additional information and the equipment cost or criticality justifies the cost.
4.5.2.1 Visual and Odor

Simple inspections can be performed weekly by the equipment operator to look at and smell the
lubricating oil. A visual inspection looks for changes in color, haziness or cloudiness, and
particles. This test is very subjective but can be an indicator of recent water or dirt
contamination and advancing oxidation. A small sample of fresh lubricating oil, in a sealed,
clear bottle, can be kept on-hand for visual comparison. A burned smell may indicate oxidation
of the oil and other odors could indicate contamination. Odor is more subjective than the visual
inspection because sensitivity to smell is different between people and there is not an effective
way to compare the odor between samples. The operator must be careful not to introduce dirt
into the system when taking a sample.
4.5.2.2 Viscosity
Indicates oil flow rate at a specified temperature. An increase or decrease in viscosity over time
measures changes in the lubricant condition or lubricant contamination. Viscosity can be tested
using portable equipment, or more accurately in a laboratory using ASTM D445 procedure.
Viscosity is measured in Centistoke (cSt) and minimum and maximum values are identified by
ISO grade. Testing is usually part of a commercial laboratory standard test package.
4.5.2.3 Water
Water in lubricating oil and hydraulic fluid contributes to corrosion and formation of acids.
Small amounts of water (less than 0.1%) can be dissolved in oil and can be detected using the
crackle test or infrared spectroscopy (minimum detectable is .05% or approximately 500 PPM;
both methods), the ASTM D95 distillation method (minimum detectable is .01%/100 PPM), or
the ASTM D1744 Karl Fischer method (minimum detectable is .001%/10 PPM). Greater than
4-70 February 2000

0.1% water, if suspended or emulsified in the oil, will appear cloudy or hazy. Free water in oil
collects in the bottom of reservoirs and can be found by draining from the bottom.
4.5.2.4 Percent Solids/Water

A simple, inexpensive test is used to provide a gross estimate of solids and/or water in the oil. A
sample is centrifuged in a calibrated tube and the resulting volume is measured. The test is
effective for amounts in the range of 0.1% to 20% of volume and is usually part of a commercial
laboratory standard test package.
4.5.2.5 Total Acid Number (TAN)

Total acid is an indicator of the lubricating oil condition and is monitored relative to the TAN of
new oil. In some systems the TAN will also be used to indicate acid contamination. TAN is
measured in milligrams of potassium hydroxide (KOH) per gram of oil (mgKOH/g). KOH is
used in a titration process where the end point is indicated by color change (ASTM D974) or
electrical conductivity change (ASTM D664).
4.5.2.6 Total Base Number (TBN)

Similar to TAN in test method, this test measures alkalinity (ability to neutralize acid) of the oil
sample. The test is used on oil with high detergent additives such as diesel and gasoline engines.
KOH is used in a titration process and the end point is indicated by electrical conductivity
change (ASTM D664 or ASTM D2896). When comparing test results (for example, against
baseline data from the oil supplier), ensure that the same test method is used as results can vary
between test methods.
4.5.2.7 Spectrometric Metals

Also known as emission spectroscopy, this technique examines the light (spectrum) emitted from
the oil sample during testing and identifies up to 21 metals. Metals are categorized as wear,
contaminate, or additive metals. The procedure identifies both soluble metal and metal particles
up to 5 to 10 microns (5-10 µm). The test is moderate in cost and is usually part of a commercial
laboratory standard test package. Other techniques, such as absorption spectroscopy and X-ray
spectroscopy, are also used by some laboratories to identify metals.
4.5.2.8 Infrared Spectroscopy

Also known as infrared analysis, infrared absorption spectroscopy or spectrophotometry, and
Fourier Transform Infrared (FTIR) spectroscopy. The technique examines the infrared
wavelength that is absorbed by the oil sample. The test is used to identify non-metallic
contamination (see Water, discussed earlier) and lubricant conditions (such as oxidation and anti-
oxidant and other additive depletion). Ongoing work is coupling computer expert system
analysis with known oil spectrums to produce highly accurate diagnosis of small changes in the
oil condition. Costs vary depending on the level of sophistication required. Infrared
spectroscopy is usually part of a commercial laboratory standard test package.
February 2000 4-71

4.5.2.9 Particle Counting

Particle counting is used to identify metal and non-metal particles over 5 microns and up to 40 to
50 microns. Two methods are used and each has advantages and drawbacks. Both methods
result in particle counts (parts per milliliter) by size category. For example, the ISO size
categories are greater than 5, 10, 15, 25 and 50 microns. The visual method of particle counting
is time consuming and depends on the analyst skill. The benefit of the visual method is that the
analyst is able to identify the types of particles such as dirt, seal material, and metal. The
electronic counting method is much faster and does not depend on the analyst’s ability but it does
not distinguish or identify the particle make up. A commercial laboratory will quote electronic
particle count; visual particle counting is only done on request and costs more.
4.5.2.10 Direct-Reading (DR) Ferrography

Ferrography, the analysis of ferrous material, uses a magnetic technique to separate wear
particles from the oil sample. In the DR process the wear particles are further separated into
small (5 to 15 microns) and large (greater than 15 microns) categories. This results in two
values, a ratio of large to small particles and a total particle concentration. Both values can be
tracked and trended and indicate increases in wear and type of wear. Test is moderate cost and
supplements spectrometric metals test. Note also that test identifies large wear particles that are
not identified in spectrometric metals test.
4.5.2.11 Analytical Ferrography

More detailed than DR ferrography, analytical ferrography is often initiated based on changes in
DR, spectrometric metal increases, or increased particle count. The analysis is sometimes
performed on a regular basis on high cost or critical machines. Process is labor intensive and
involves the preparation of sample and then examination under magnification. Results depend
on analysts capability but the procedure can provide detailed information regarding wear
material such as wear type (rubbing, sliding, cutting), color, particle types (oxide, corrosive,
crystalline), and other non-ferrous particles. This detailed information can be critical in finding
the root cause of wear problems. Costs are moderately high; test is performed on a fixed price
basis (per sample) from a commercial laboratory.
4.5.3 Special Tests

Special tests are sometimes needed to monitor lubricant conditions on some high cost or critical
systems. Usually the special test is monitoring a lubricant contaminate, a characteristic or
additive depletion. This section identifies some of the special tests available. Special tests are
rarely needed for routine monitoring of lubricants and the tests listed here are provided as
samples. Test procedures are constantly being developed and refined. The annual ASTM
Standards12 provide a description of current test methods.
12
Annual Book of ASTM Standards, Section 5, Petroleum Products, Lubricants, and Fossil Fuels, American Society
for Testing and Materials
4-72 February 2000

4.5.3.1 Glycol Antifreeze

Glycol contamination can be detected using infrared spectroscopy (see Infrared Spectroscopy,
discussed earlier) at levels greater than 0.1% (1,000 PPM) which is usually adequate for
condition monitoring. However, additional tests can be specified to identify if small amounts of
glycol are present. ASTM test D2982 will indicate if trace amounts are present. ASTM D4291
uses gas chromatography to quantify small amounts of glycol.
4.5.3.2 Karl Fischer Water

Water contamination can be detected using infrared spectroscopy (see Infrared Spectroscopy,
discussed earlier) at levels greater than 0.05% (500 PPM) which is usually adequate for
condition monitoring. Using a titration process with a Karl Fischer reagent, low levels of water
can be quantified. The test, ASTM D1744, is useful when accepting new oil or evaluating clean
up efforts. Cost of the test is moderate.
4.5.3.3 Foaming
Some oil may have anti-foam agents added to improve the lubrication capability in specific
applications such as gearboxes or mixers. ASTM test D892 can be used to test the oils foam
characteristics. The test blows air through a sample of the oil and then the foam volume is
measured. Cost of the test is moderately high.
4.5.3.4 Rust Prevention

Some systems are susceptible to water contamination due to equipment location or the system
operating environment. In those cases, the lubricating oil or hydraulic fluid may be fortified with
a corrosion inhibitor to prevent rust. The effectiveness of rust prevention can be tested using
ASTM D665 (or ASTM D3603). Results are pass/fail and the cost of the test is high.
4.5.3.5 Rotating Bomb Oxidation Test (RBOT)

Also known as Rotary Bomb Oxidation Test, ASTM D2272, is used to estimate oxidation
stability and, therefore, identify the remaining useful life of oil. The test simulates aging to
identify when rapid oxidation takes place indicating that anti-oxidants have been depleted. Test
is not a one-time test; it must be performed over time, including a baseline test with new oil, in
order to develop a trend line. Because of the high cost, and the multiple tests required, this test is
usually only performed on large volume reservoirs or expensive oil.
4.5.4 Application
All machines with motors 7.5 HP or larger, and critical or high cost machines should be
evaluated for routine lubricating oil analysis. The analysis schedule should be adjusted in the
same way that the vibration analysis schedule is adjusted. It is important that there is a dynamic
process for addressing the adjustment of periodicity for all equipment in both the PM and PT&I
programs. Analyze more frequently for machines that are indicating emerging problems; less
frequently for machines that have stable conditions and are not run on a continuous basis. A new
February 2000 4-73

baseline analysis will be needed following machine repair or oil change out. All hydraulic
systems, except mobile systems, should be analyzed on a quarterly basis. Mobile systems should
be considered for analysis based upon the machine size and the cost effectiveness of performing
the analysis. Generally speaking, it is more cost effective in mobile equipment to maintain the
hydraulic fluid based upon the fluid condition. However, for small systems, the cost to flush and
replace the hydraulic fluid on a time basis may be lower than the cost to analyze the fluid on a
routine basis. Grease is usually not analyzed on a regular basis. Although most of the testing
that is done on oil can also be done on grease, there is a problem getting a representative sample.
In order to get a representative sample- one that is a homogeneous mixture of the grease,
contaminants, and wear- the machine must usually be disassembled. Analysis of grease to
diagnose a failure can sometimes be useful.
A concern common to all machines with lubricating oil systems is keeping dirt and moisture out
of the system. Common components of dirt, such as silica, are abrasive and naturally promote
wear of contact surfaces. In hydraulic systems, particles can block and abrade the close
tolerances of moving parts. Water in oil promotes oxidation and reacts with additives to degrade
the performance of the lubrication system. Ideally, there would be no dirt or moisture in the
lubricant; this, of course, is not possible. The lubricant analysis program must therefore monitor
and control contaminants. Large systems, with filters, will have steady state levels of
contaminates. Increases in contaminates indicate breakdown in system integrity (leaks in seals,
doors, heat exchangers, etc.) or degradation of the filter. Unfiltered systems can exhibit steady
increases during operation. Operators can perform a weekly visual and odor check of lubricating
systems and provide a first alert to contamination. Some bearing lubricating systems have such a
small amount of oil that a weekly check may be impractical.
4.5.4.1 Motors, Generators, Pumps, Blowers, Fans

For those machines that have been selected for monitoring (as discussed in Section 2) and have
less than 5 gallons in the lubrication system, the analyst is mostly concerned with machine
condition. Lubricant condition and contamination are of interest in that they contribute to
machine condition i.e. viscosity, percent solids/water, and spectrometric metals. Monitor trends
and discard or refresh the oil when viscosity changes 10% from the baseline. Viscosity normally
increases above the baseline with the oil service time. If the viscosity decreases below the
baseline, it usually means that the oil is contaminated, probably from adding the wrong makeup
oil. There should be no water present (minimum detectable with the percent solids/water test is
0.1%). If there is water, the source of the water needs to be identified and corrected.
For machines with more than 5 gallons of oil in the system, add infrared spectroscopy (minimum
amount of water detectable is .05%) and particle counting. Changes in particle count can
indicate increased contamination or increased wear; correlate particle count with spectrometric
metals. The rate of particle count change indicates how quickly the lubricant is degrading.
Visual particle counting can be used to identify the source of the contamination. In addition,
perform DR ferrography for high cost or critical machines. In all machines, changes in
spectrometric metals or DR should be investigated further using analytical ferrography and
correlated with vibration analysis.
4-74 February 2000

4.5.4.2 Gearboxes
Same as above, with the following additions. For all gearboxes, including those with less than 5
gallons of oil, add particle counting. Include DR ferrography for high cost or critical gearboxes.
Monitor trends and correlate with vibration readings.
4.5.4.3 Chillers
In addition to the items identified above, add TAN and Direct Read ferrography.
4.5.4.4 Diesel Engines

Same as chillers except substitute TBN for TAN when oil has high detergent additives. A
decrease in viscosity below the baseline may indicate fuel contamination. Coolant leakage
(glycol and other characteristics) is identified from the infrared spectroscopy analysis.
4.5.4.5 Compressors
Centrifugal compressors; same as chillers. Reciprocating compressors; same as diesel engines.
4.5.4.6 Hydraulic Systems

Same as gearboxes. Monitor particle count by ISO category. Each hydraulic system will have
limiting clearances that will determine critical particle sizes. Note that some hydraulic systems
use fluids other than oil (water or glycol). Particle control is the same for these systems. See
Table 7 – 9.
4.5.4.7 Large Reservoirs

For reservoirs over 500 gallons, consider performing an RBOT to assess the oxygen stability.
Cost is usually the deciding factor. At least three tests are needed to develop a trend and then
additional retesting at least once a year. Benefit is derived when replacement or refreshing of a
large volume of oil (or smaller volume of expensive oil) can be deferred.
4.5.4.8 Lubrication Analysis

Figure 4–3, Lubrication Analysis Chart, summarizes the various lubricant tests, monitoring
interval, and application.
February 2000 4-75

Figure 4 – 3. Lubrication Analysis Chart
4-76 February 2000

4.5.5 Sampling
Oil samples must be collected safely and in a manner that will not introduce dirt and other
contaminates into the machine/system or into the sample. It may be necessary to install
permanent sample valves in some lubricating systems to do this. The oil sample should be
representative of the oil seen in the machine. The sample should, therefore, be collected from a
mid-point in reservoirs and prior to filtering in circulating systems. Sample collection bottles
and tubing can be procured through testing laboratories. The testing laboratory will also be able
to provide guidance as regards to the cleanliness level needed. Oil sample pumps for extracting
oil from reservoirs must be used properly to avoid contamination. Samples must be collected
from the same point in the system in order to assure consistency in the test analysis; therefore,
the maintenance procedure must provide detailed direction on where and how to collect samples.
The equipment operators can collect samples. Each sample is marked with the system/machine
name, sample location point (the system may have multiple sample points), date, elapsed
operating time for the system/machine, and other comments such as last “topping off” or filtering
operation. The analyst will also need to know the amount of oil in the reservoir in order to make
recommendations to correct abnormalities.
Additional information on sampling points and techniques is contained in Section 7.1.9.
4.6 Electrical Condition Monitoring

A major portion of a facility’s capital investment is represented by electrical equipment. From
the power distribution system to electric motors, the electrical systems efficient operation is
crucial to maintaining operational capability. Electrical condition monitoring encompasses
several technologies and techniques that provide critical information so a comprehensive system
evaluation can be performed.
Monitoring key electrical parameters provides the information to detect and correct electrical
faults such as high resistance connections, phase imbalance and insulation breakdown. Since
faults in electrical systems are seldom visible, these faults are costly (increased electrical usage),
present safety concerns (fires) and life cycle cost issues (premature replacement of equipment).
According to the Electric Power Research Institute13, voltage imbalances of as little as 5% in
motor power circuits result in a 50% reduction in motor life expectancy and efficiency in 3 phase
AC motors. A 25% increase in motor temperatures can be generated by the same 5% voltage
imbalance accelerating insulation degradation.
4.6.1 Techniques
• Infrared Thermography
• Insulation Power Factor Testing
• Insulation Oil Analysis
13
EPRI is a nonprofit membership corporation, established by U.S. electric utilities, to manage a national research
program on behalf of its members.
February 2000 4-77

• Gas-in-Oil Analysis
• Megohmmeter Testing
• High Potential Testing (HiPot)
• Airborne Ultrasonics
• Battery Impedance Testing
• Surge Testing
• Motor Circuit Analysis (MCA)
• Motor Current Signature (Spectrum) Analysis
• Very Low Frequency Testing (VLF)
• Circuit Breaker Timing Tests
• Circuit Breaker Contact Resistance
(Note: HiPot and surge testing should be performed with caution. The high voltage applied
during these tests may induce premature failure of the units being tested. For that reason these
tests are normally performed only for acceptance testing, not for condition monitoring.)
4.6.1.1 Infrared Thermography

Infrared thermography has widespread application in electrical systems, because of its ability to
be used safely on energized equipment, to detect temperature differences and overheating of
circuits. See the discussion earlier in this section for more information.
4.6.1.2 Insulation Power Factor

Insulation Power Factor, sometimes referred to as dissipation factor, is the measure of the power
loss through the insulation system to ground. It is a dimensionless ratio, which is expressed in
percent of the resistive current flowing through an insulation to the total current flowing. To
measure this value a known voltage is applied to the insulation and the resulting current and
current/voltage phase angle is measured. Figure 4-4 shows the phase relationships of the
resulting currents. IR is the resistive current, IC is the capacitive current, IT is the resultant, or
total current, and V is the applied voltage.
Usually, IR is very small compared to IT because most insulation is capacitive in nature. As a

comparison, look at the similarities between a capacitor and a piece of electrical insulation. A
capacitor is two current carrying plates separated by a dielectric material. An electrical coil,
such as would be found in a transformer or motor, is a current carrying conductor, with an
insulation material protecting the conductor from shorting to ground. The conductor of the coil
and ground are similar to the two conducting plates in the capacitor, and the insulation of the coil
is like the dielectric material of the capacitor. The dielectric material prevents the charge on
each plate from “bleeding through” until such a time that the voltage level of the two plates
exceeds the voltage capacity of the dielectric. The coil insulation prevents the current from
4-78 February 2000

flowing to ground, also until such a time that the voltage level exceeds the voltage capacity of
the insulation.
Ic IT
Current (I)
)
V = Applied Voltage
IT= Total Current
IR = Resistive Current
IC = Capacitive Current
Dissipation Factor = tan)
Power Factor = cos2
IR
2
Voltage Applied (V)
Figure 4 – 4. Power Factor Current/Voltage Relationship
Referring back to Figure 4 - 4, it can be seen that IR is in phase with the applied voltage V and IC
is leading the voltage by a phase angle of 90 degrees. The total current is the resultant
combination of both IR and IC. The tangent of the angle between the applied voltage and
resultant current is called the dissipation factor and the cosine of the angle between the resultant
current and the capacitive current is called the power factor.
As the impedance of the insulation changes due to aging, moisture, contamination, insulation
shorts, or physical damage the ratio between IC and IR will become less. The resulting phase
angle between the applied voltage and resultant current then becomes less, and the power factor
will rise. Consequently, the power factor test is primarily used for making routine comparisons
of the condition of an insulation system. The test is non-destructive, and regular maintenance
testing will not deteriorate or damage insulation. It is one of the best electrical PT&I tests.
4.6.1.3 Insulation Oil Analysis

High and medium voltage transformers, some high and medium voltage circuit breakers, and
some medium voltage switches are supplied with mineral oil as an insulation medium.
Performing an analysis of that insulating oil can yield a wealth of information as to the
operational history and current condition of the equipment. Below are listed available tests, the
ASTM standard number14 (note that several of these standards were discussed in the lubricating
oil section), and a brief description of what each test reveals.
14
Annual Book of ASTM Standards, Section 5, Petroleum Products, Lubricants, and Fossil Fuels, American Society
for Testing and Materials
February 2000 4-79

a. Karl Fischer, ASTM D-1533-88—Tests for water in insulating fluids. This test
reveals total water content in oil, both dissolved and free. High readings could indicate
a leak in the equipment housing or insulation breakdown.
b. Dielectric Breakdown Strength, ASTM D-877 and D-1816—Tests for conductive

contaminants present in the oil such as metallic cuttings, fibers, or free water.
c. Neutralization Number, ASTM D-974—Commonly called the acid number, this

measurement indicates the amount of acid in the oil. Acidity is a result of oxidation of
the oil caused by the release of water into the oil from insulation material due to aging,
overheating, or operational stresses such as internal or through faults. Acidity is
measured as the number of milligrams of potassium hydroxide (KOH) it takes to
neutralize the acid in one gram of oil. An increase in acidity indicates a deterioration of
the oil. This process causes the formation of sludge within the windings which in turn
can result in premature failure of the unit.
d. Interfacial Tension(IFT), ASTM D-971—Measures the tension at the interface

between two immiscible liquids, oil and water. It is expressed in dynes/centimeter.
This test is extremely sensitive to oil decay products and contamination from solid
insulating materials. Good oil will have an IFT of 40 to 50 dynes/cm, and will
normally “float” on top of water. As transformer and breaker insulation ages,
contaminates such as oxygen and free water are released into the oil. The properties
that allow the oil to “float” on top of the oil then begin to break down and the result is a
lower IFT. Along with the neutralization number, the IFT can reveal the presence of
sludge in insulating oils.
e. Color, ASTM D-1524—as insulating oils in electrical equipment age, the color of the
oil tends to gradually darken. A marked color change from one year to the next could
indicate a deteriorating oil.
f. Sediment, ASTM D-1698—indicates deterioration and/or contamination of the oil.
g. Power Factor, ASTM D-924—taken at 25 o C, this test can reveal the presence of
moisture, resins, varnishes, or other products of oxidation or foreign contaminates such
as motor or fuel oil. The power factor of new oil should always be below 0.05%.
h. Visual Examination, ASTM D-1524—insulating oil is clear and sparkling, not cloudy
and dull. Cloudiness indicates the presence of moisture or other contaminates. This is
a good “quick look” field test and can be used to trigger a Karl Fischer or Dielectric
Breakdown test.
4.6.1.4 Gas-in-Oil Analysis

Gas-in-oil analysis, also called dissolved gas analysis, is probably the best predictive test for oil
filled transformers. As transformers age small amounts of combustible gases are formed,
however when insulation systems are subjected to stresses such as fault currents and overheating
4-80 February 2000

combustible gas generation can change dramatically. In most cases these stresses can be
detected early on; the presence and quantity of the individual gases can be measured and the
results analyzed to indicate the probable cause of generation.
A small oil sample (50cc) is drawn from a transformer with a glass syringe15. To obtain a
reliable reading this must be accomplished with the unit energized. A transformer cools after
being taken off-line. As the transformer cools, dissolved gases in the oil will migrate into the
windings so the sample must be taken when the transformer is energized and at operating
temperature.
The oil is analyzed using ASTM D-3612-90, Standard Test Method for Analysis of Gases
Dissolved in Electrical Insulating Oil by Gas Chromatography. While there are over 200 gasses
present in insulating oils there are only nine that are monitored. They are:
• Nitrogen (N2)
• Oxygen (O2)
• Carbon Dioxide (CO2)
• Carbon Monoxide (CO)
• Methane (CH4)
• Ethane (C2H6)
• Ethylene (C2H4)
• Hydrogen (H2)
• Acetylene (C2H2)
Different combinations of these gasses reveal different conditions. Large amounts of CO and CO2
indicates overheating in the windings, CO, CO2, and CH4 show the possibility of hot spots in the
insulation, H2, C2H6, and CH4 are indicative of corona discharge, and C2H2 is a sign of internal
arcing. Various industry publications exist to help determine potential problems.
4.6.1.5 Megohmmeter Testing

A hand-held generator (battery powered or hand cranked) is used to measure the insulation
resistance phase-to-phase or phase-to-ground of an electric circuit. Readings must be
temperature-corrected to trend the information. Winding temperatures affect test results. An
enhanced technique compares the ratio of the Megohmmeter readings after one minute and ten
minutes. This ratio is referred to as the polarization index.
15
ASTM D3613 provides a detailed procedure. D3613, Standard Test Methods of Sampling Electrical Insulating
Oils for Gas Analysis and Determination of Water Content, American Society for Testing and Materials.
February 2000 4-81

4.6.1.6 High Potential Testing (HiPot)

HiPot testing applies a voltage equal to twice the operating voltage plus 1000 volts to cables and
motor windings testing the insulation system. This is typically a go/no-go test. Industry practice
calls for HiPot test on new and rewound motors and on new cables. This test stresses the
insulation systems and can induce premature failures in marginal insulation systems. Due to this
possibility, HiPot is not recommended as a routinely repeated condition monitoring technique,
but as an acceptance test. An alternative use of the equipment is to start with a lower voltage and
increase the applied voltage in steps and measure the change in insulation resistance readings. In
repaired equipment, if the leakage current continues to increase at a constant test voltage this
indicates the repair is not to the proper standard and will probably fail soon. In new equipment,
if the equipment will not withstand the appropriate test voltage it indicates the insulation system
or construction method is inadequate for long term service reliability.
4.6.1.7 Airborne Ultrasonic Noise

Electrical arcing and discharges create noise in the upper, or ultrasonic frequency ranges,
sometimes long before a failure occurs. Things like corona discharges in switchyards, loose
switch connections, and internal arcing in deadfront electrical connections can all sometimes be
heard with an ultrasonic noise detector. Also see the additional information in Section 4.4.
4.6.1.8 Battery Impedance Testing

Batteries are DC energy storage devices with many shapes, sizes, capacities, and types. All
batteries have a storage capacity which is dependent on the terminal voltage and internal
impedance. A battery impedance test set places an AC signal between the terminals of the
battery. The resulting voltage is measured and the impedance then calculated. This
measurement can be accomplished without removing the battery from service since the AC
signal is low level and "rides" on top of the DC voltage of the battery. Two comparisons are
then made: first, the impedance is compared with the last reading for that battery: and, second,
the reading is compared with other batteries in the same bank. Each battery should be within
10% of the others and 5% of its last reading. A reading outside of these values indicates a cell
problem or capacity loss. Additionally, if the battery has an internal short the impedance tends to
go to zero. If there is an open the impedance will try to go to infinity, and premature aging due
to excessive heat or discharges will cause the impedance to rise quickly.
There are no set guidelines and limits for this test. Each type, style, and configuration of battery
will have its own impedance so it is important to take these measurements early in a battery's
life, preferably at installation. It should take less than an hour to perform this test on a battery
bank of 60 cells.
4.6.1.9 Surge Testing

Surge Testing utilizes equipment based on two capacitors and an oscilloscope to determine the
condition of motor windings. This is a comparative test evaluating the difference in readings of
identical voltage pulses applied to two windings simultaneously. Like HiPot testing, the applied
voltage equals two times operating voltage plus 1000 volts. This test also is primarily an
4-82 February 2000

acceptance, go/no-go test. Data is provided as a comparison of waveforms between two phases
indicating the relative condition of the two phases with regard to the insulation system (short
circuits). Because of the repeated stress of the insulation system, Surge testing is not
recommended for routine condition monitoring.
4.6.1.10 Motor Circuit Analysis

The motor circuit analysis technology packages several motor tests into a single unit. The test
device will check the following test parameters in a motor circuit: resistance to ground,
capacitance to ground, resistive imbalance, inductive imbalance, rotor influence, and will
perform a polarization index. The tests are performed with the motor de-energized and use low
voltage that does not over stress the insulation system. Data is collected by the unit and enables
trending and comparing with similar motors.
The total resistance of a conductor is the sum of its resistance, capacitive and inductive
impedance. Accurate measurement of the conductor’s impedance allows minor degradations in a
motor to be detected and addressed prior to a failure. The condition of the insulation system can
be determined by measuring the capacitance between each phase and ground. The presence of
moisture or other conducting substance will form a capacitor with the conductor being one plate,
the insulation the dielectric, and the contaminate forming the second plate. Maintaining proper
inductive balance is imperative to efficient operation and realizing full lifetime of electrical
equipment. An electrical imbalance leads to elevated winding temperatures and reduced
insulation life.
4.6.1.11 Motor Current Signature (Spectrum) Analysis (MCSA)

MCSA is a remote, non-intrusive, on-line method of testing motor driven equipment. Current
and voltage probes provide the signal data used for analysis to detect equipment degradation. It
can be compared to vibration analysis in the methods both use to analyze data. Motor current
spectrums in both time and frequency domains are collected with a clamp-on ammeter and FFT
analyzer. Rotor bar problems will appear as side-bands around the power supply line frequency.
MCSA allows for diagnosis of power circuit, motor and driven end component.
MCSA can be performed in an indirect manner by measuring the magnetic flux produced by the
motor and analyzing the data using the FFT process to identify the presence of electrical fault
frequencies.
4.6.1.12 Very Low Frequency Testing

A Very Low Frequency (VLF) Test Set is an AC test that operates at 0.1 HZ. The low frequency
allows for the portability of a DC test set (light weight, less input current) without the destructive
capability of a HiPot. The primary application of VLF testing is for partial discharge and over
potential testing of large rotating machines, power cables, and other high capacitance apparatus.
The results can be trended to monitor degradation. The high cost of a VLF test set limits its use
to facilities with large electrical systems.
February 2000 4-83

4.6.1.13 Circuit Breaker Timing Tests

This is a mechanical test to monitor the speed and position of breaker contacts before, during,
and after an operation. The first timing devices, called Drop-Bar Recorders, recorded their
results on a rotating drum. Developed in the late 1930s, it was the instrument of choice until the
coming of rotary motion, vacuum, and high-speed breakers in the mid 1970s.
For in-service circuit breakers, a digital contact and breaker analyzer can be used to measure the
contact velocity, travel, over travel, bounce back, and acceleration to indicate the condition of the
breaker operating mechanism. A voltage is applied to the breaker contacts and a motion
transducer is attached to the operating mechanism. The breaker is then closed and opened. The
test set measures the timeframe of voltage changes, and plots the voltage changes over the
motion waveform produced by the motion transducer. The numbers are normally printed out
from the test set, and the chart is stored in memory for downloading into a computer.
Analyzing and trending this information allows for adjustments to the breaker operating
mechanism when necessary. This test is not applicable to molded case breakers or low voltage
breakers.
4.6.1.14 Circuit Breaker Contact Resistance

This test is used to determine the contact condition on a breaker or switch without visual
inspection. The results of this test can be trended over time to help in scheduling maintenance
activities before the contacts degrade significantly.
Most manufacturers of high and medium voltage circuit breakers will specify a maximum
contact resistance for both new contacts and in-service contacts. The contact resistance is
dependent on two things, the quality of contact area and the contact pressure. The contact
quality can degrade if the breaker is called upon to open under fault conditions. The contact
pressure can lessen as the breaker springs fatigue due to age or a large number of operations.
To measure the contact resistance a DC current, usually 10 or 100 amps, is applied through the
contacts. The voltage across the contacts is measured and the resistance is calculated using
Ohms law. This value can be trended and compared with maximum limits issued by the breaker
or switch manufacturer. It should be noted that for oil filled breakers, using a 100 amp test set is
recommended because oil tends to glaze on contact surfaces and, in some cases, 10 amps is not
enough current to overcome the glaze.
4.6.2 Additional Techniques and Troubleshooting

There are numerous electrical tests that, while not forecast orientated, provide indications of the
system condition.
4.6.2.1 Time Domain Reflectometry

A voltage spike is sent through a conductor. Each discontinuity in the conductor path generates
a reflected pulse. The time difference between initial pulse and reception of the reflected pulse
4-84 February 2000

indicate the location of the discontinuity. This technology is used for power cables to help locate
faults within a cable run. The test is performed with the cable de-energized.
4.6.2.2 Power Factor and Harmonic Distortion

Maintaining optimum power factor maximizes the efficient use of electrical power. Power factor
is the ratio of real power to reactive power usage. Dual channel data-loggers are used to
determine the phase relationship between voltage and current, then calculate the power factor.
Addition of power factor enhancing capacitors is then evaluated as a means of improving power
system power factor.
Harmonic distortion is a result of having non-linear loads on the power system. These loads
include laser printers, desktop computers, and SCRs found in variable speed motor controls.
High levels of harmonic current cause excessive heating in transformers and cables, which
reduce service life and cause spurious tripping of circuit breakers, which can be a major
inconvenience. A harmonic analyzer is used to measure the harmonic current and identify the
source. Filters can then be placed on the circuit to minimize the impact. This test is performed
with the system energized.
4.6.2.3 Motor Starting Current and Time

Starting current in electric motors can routinely exceed five times full load running current. The
amount of starting current combined with the duration of the starting surge can indicate the
condition of electrically driven equipment. Higher starting current and longer duration of the
surge can indicate mechanical problems such as increased friction due to misalignment of the
mechanical components of the equipment. Alternatively, coastdown tests using timing devices
and vibration monitoring equipment can verify the presence of magnetically induced vibrations
or mechanical friction.
4.6.2.4 Transformer Turns Ratio (TTR)

This test measures the turns-ratio of a transformer and is mainly used as an acceptance test. It
can also be used as a trouble shooting tool when other electrical tests reveal a possible problem.
During routine maintenance tests a TTR can be performed to identify short circuited turns,
incorrect tap settings, mislabeled terminals, and failure in tap changers.
The test is performed by applying a voltage across the primary windings and measuring the
resulting voltage across the secondary winding. The ratio of active windings can be calculated.
This measurement can be used to determine the condition of the transformers inductive
capability. The turns ratio measurement can show that a fault exists but can not determine the
reason or location of the fault. This test is done with the transformer de-energized.
February 2000 4-85

4.6.3 Applications
4.6.3.1 Equipment to be Monitored

Specific equipment that can be monitored by electrical condition monitoring techniques are listed
below:
a. Electrical Distribution Cabling— Megohmmeter, VLF Testing, Time Domain

Reflectometry, HiPot, Infrared Thermography (if visible) and Airborne Ultrasonics.
b. Electrical Distribution Switchgear and Controllers— Breaker Timing, Insulation

Power Factor Testing, Visual Inspection, Infrared Thermography and Airborne
Ultrasonics.
c. Electrical Distribution Transformers—Oil Analysis, Turns Ratio, Power Factor

and Harmonic Distortion.
d. Electrical Motors—Motor Current Signature Analysis, Motor Circuit Analysis,

Megohmmeter, HiPot, Surge Test, , Starting Current and Coast Down Time, Infrared
Thermography, Airborne Ultrasonics.
e. Generators—Megohmmeter, VLF Testing, and Coast Down Time.
f. Distribution System—Infrared Thermography, HiPot, Airborne Ultrasonics, Power

Factor and Harmonic Distortion.
4.6.3.2 Conditions Monitored

Temperature, voltage, current, resistance, complex impedance, capacitance, insulation integrity,
phase imbalance, mechanical binding, and presence of arcing.
4.6.3.3 Detection Interval

Monitoring intervals of several weeks to several years for various technologies will provide
sufficient condition information to warn of degrading equipment condition. Specific
expectations of the length of warning provided should be factored into developing monitoring
intervals for specific technologies. Additionally, some monitoring intervals will depend on
outage cycles. Some of the electrical condition monitoring can be done with the system
energized. Several of the technologies outlined are also effective when used for acceptance
testing and certification.
.4.6.3.4 Accuracy
Accuracy is dependent on the testing technique applied and rating of the instrument.
4-86 February 2000

4.6.3.5 Limitations
The technologies presented can be divided into two categories:
a. Energized— Those technologies that can safely provide information on energized

systems and require the system be energized and operational. These technologies
include Infrared Thermography, Airborne Ultrasonics, Motor Current Readings
including Starting Current, Motor Current Spectrum Analysis, VLF Testing, Power
Factor and Harmonic Distortion, Battery Impedance Testing, Insulation Oil Analysis
(Including Gas-in-Oil).
b. De-Energized— Technologies that require the circuit to be de-energized include

Surge Testing, HiPot Testing, Time Domain Reflectometry (TDR), Megohmmeter,
Motor Circuit Analysis, , Circuit Breaker Timing, Transformer Turns Ratio, and
Insulation Power Factor Testing.
Each technology will require specific initial conditions to be set prior to conducting the test. For
instance, prior to an Infrared Thermography survey, typical equipment powered through the
switchboard should be running to bring the distribution equipment to normal operating
temperatures. Higher load accentuates problem areas. Conducting the survey at low load
conditions may allow a problem to remain undetected.
4.6.4 Logistics

A comprehensive electrical testing program includes: Infrared Camera, ultrasonic noise detector,
multi-meters/volt-ohmmeters, clamp on current transformers, Insulation Power Factor test set,
Time Domain Reflectormery test set, Breaker Timing test set, Contact Resistance (micro-
ohmmeter) test set, Battery Impedance test set, VLF test set, motor current signature analysis
soft-ware, and integrated motor circuit analysis testers.
4.6.4.2 Operations
Electricians, electrical technicians, and electrical engineers should be trained in electrical PT&I
techniques such as motor current signature analysis, motor circuit analysis including complex
phase impedance and insulation resistance readings and analysis.

Equipment vendors and independent companies provide training. See Appendix C for training
sources.
February 2000 4-87

4.6.3.4 Cost
a. Equipment—Equipment costs vary from $20 for a simple multi-meter to
approximately $40,000 for integrated motor-current analysis (MCA) testers. A full
inventory of electrical testing equipment can cost in excess of $100,000.
b. Training—Training averages between $750 and $1,000 per week per person trained
for each technology.
4.7 Non-Destructive Testing

Non-Destructive Testing (NDT) evaluates material properties and quality of manufacture for
high-value or critical components or assemblies without damaging the product or its function.
Instead of statistical sampling techniques that use only surface measurements or require the
destructive testing of selected components from a production lot, NDT is used when these testing
techniques are cost prohibitive or ineffective (see Figure 4–5). Typically, NDT has been
Conduct
Define Establish Evaluate
Failure Modes
System Equipment Regulatory
& Effects
Boundaries Criticality Requirements
Analysis
Define
Establish
Information Evaluate
Failure Modes
Required Safety & Evaluate Cost
To Be
From Access Per Point
Addressed By
NDT Constraints
NDT
Technique
Select NDT
Technique Refer To
Determine Based on Establish Section XX To Document &
Skills Information, Sampling Establish Formalize
Requried Access, Cost Locations Sampling Program
& Skills Intervals
Requried
Figure 4 – 5. NDT Technique Selection Process
4-88 February 2000

associated with welding of large high stress components such as pressure vessels and structural
supports. Process plants such as refineries or chemical plants use NDT techniques to assure
integrity of pressure boundaries for systems processing volatile substances.
4.7.1 Techniques
a. Radiography—Detection of deep sub-surface defects. Radiography or x-ray is one of
the most powerful NDT techniques available in industry. Depending on the strength of
the radiation source, radiography can provide a clear representation (radiograph) of
discontinuities or inclusions in material several inches thick. X-ray or gamma ray
sensitive film is placed on one surface of the material to be examined. The radiation
“source” is positioned on the opposite side of the piece. The source may be either a
natural gamma emitter or a powered X-ray emitter. The source is accurately aligned to
assure the proper exposure angle through the material (Figure 4–6). When all
preparations and safety precautions are complete, radiation source energized or
unshielded. The gamma or x-rays passing through the material to the film expose the
film.
By developing the film in a similar manner to photographic film, an image of defects or

inclusions in the material is produced. More advanced radioluminescent film does not
require photographic processing. Multiple “shots” from varying angles provide a
complete picture of the thickness of the material. Dual angles are required to determine
the size and orientation of an inclusion.
Once the type, size and orientation of each inclusion are defined, these can be classified
into either acceptable inclusions or unacceptable defects.
Defects in the material must be accurately located to facilitate minimal material

removal, yet assure the defect has been completely eliminated. Minimizing material
removal also supports reduction in repair cost and reduces the likelihood of additional
defects created by the repair. The repair is then re-evaluated to assure the defect
removal and subsequent repair were conducted properly.
Radiography, though a versatile tool, is limited by the potential health risks. Use of
radiography usually requires the piece be moved to a special shielded area (Figure 4–6)
or personnel evacuated from the vicinity to avoid exposure to the powerful radiation
source required to penetrate several inches of dense material. Temporary shielding may
also be installed, but the installation and removal of thousands of pounds of lead is
labor intensive. Radiography technicians are trained in radiation health physics and
material properties. These technicians can visually distinguish between welding slag
inclusions, porosity, cracking and fatigue when analyzing radiographic images.
b. Ultrasonic Testing (Imaging)—Detection of deep sub-surface defects. Ultrasonic

(UT) inspection of welds and base material is often an alternative or complementary
NDT technique to radiography. Though more dependant on the skill of the operator,
UT does not produce the harmful radiation encountered with radiography. UT
inspection is based on the difference in the wave reflecting properties of defects and the
February 2000 4-89

Radiography Area
Shielded Walls
Radiation Hazard
Area
Radiation Source
Positions
Welded Radiographic
Joint Film
Figure 4 – 6. Shielded Radiography Enclosure
surrounding material. An ultrasonic signal is applied through a transducer into the

material being inspected. The speed and intensity with which the signal is transmitted
or reflected to a transducer provides a graphic representation of defects or
discontinuities within the material. A couplant fluid is often used to provide a uniform
transmission path between the transducer, receiver and the material of interest.
Transducer configurations differ depending on the type of system used. Some systems
use a single transducer to transmit and receive the test signal. Others utilize a
transmitting transducer in conjunction with a separate receive transducer. Dual
transducer systems may be configured with both transducers on the same surface of the
material or with transducers on the opposite surfaces of the material.
4-90 February 2000

Three scan types are most commonly used; A Scan, B Scan and C Scan. A-Scan
systems analyze signal amplitude along with return time or phase shift as the signals
travel between a specific surface and discontinuities. B Scan systems add signal
intensity modulation and capability to retain video images. C Scan systems include
depth gating to eliminate unwanted returns.
UT inspection is a deliberate process covering a small area (four to eight square inches)
at each sampling. Consistency in test method and interpretation of results is critical to
the reliable test results. Surface preparation is also critical to reliable UT results. Any
surface defects such as cracks, corrosion, or gouges will adversely affect the reliability
of UT results.
Due to the time and effort involved in surface preparation and testing, UT inspections
are often conducted on representative sites such as high stress, high corrosion areas and
large welds. By evaluating the same sites at regular intervals, monitoring of the
condition of the material can be accomplished. 100% UT inspection is typically
reserved for original construction of high stress components such as nuclear reactor
vessels or chemical process vessels.
c. Magnetic Particle—Detection of shallow sub-surface defects. Magnetic Particle

Testing (MT) techniques are useful during localized inspections of weld areas and
specific areas of high stress or fatigue loading. MT provides the opportunity to locate
shallow sub-surface defects. Two electrodes are placed several inches apart on the
surface of the material to be inspected. An electric current is passed between the
electrodes producing magnetic lines. While the current is applied, iron ink or powder is
sprinkled in the area of interest. The iron aligns with the lines of flux. Any defect in
the area of interest will cause distortions in the lines of magnetic flux, which will be
visible through the alignment of the powder, see Figure 4–7. Surface preparation is
important since the powder is sprinkled directly onto the metal surface and major
surface defects will interfere with sub-surface defect indications. Also, good electrode
contact and placement is important to assure consistent strength in the lines of magnetic
flux.
A major advantage for MT is its portability and speed of testing. The electrodes are
hand-held which allows the orientation of the test to be changed in seconds. This
allows for inspection of defects in multiple axes of orientation. Multiple sites can be
inspected quickly without interrupting work in the vicinity. The equipment is portable
and is preferred for on-site or in-place applications. The results of MT inspections are
recordable with a high quality photograph or transfer to tape. Fixing compounds are
available to “glue” the particle pattern in-place on the test specimen. Interpretation of
results is dependent on the experience of the operator.
February 2000 4-91

Electrodes & Defect Interrupting

Cables to Power Magnetic Lines of
Source Flux
Base Metal
Visible Pattern of Identified &

Iron Powder Aligned Marked Defect
With Lines of
Magnetic Flux
Figure 4 – 7. Magnetic Particle Testing
d. Dye Penetrant—Detection of surface defects. Dye Penetrant (DP) inspections provide

a simple method for detecting surface defects in non-porous materials. DP allows large
areas to be quickly inspected. Once the surface has been cleaned, a penetrating dye
(magenta or fluorescent color) is sprayed liberally on the entire surface. The dye is
allowed to penetrate for several minutes. The excess dye is then wiped from the
surface leaving only the dye that has been drawn into surface defects. A developer
(usually white) is sprayed on the entire surface (same area as the dye application). The
developer draws the dye from the defects producing a visual indication of the presence
of surface defects. The defective areas are then identified for repair and the remaining
dye and developer are removed.
e. Hydrostatic Testing—Detection of breeches in a system’s pressure boundaries.

Hydrostatic Testing (Hydro) is an NDT method for detecting defects that completely
penetrate pressure boundaries. Hydros are typically conducted prior to the delivery or
operation of completed systems or sub-systems that act as pressure boundaries. As the
name implies, hydrostatic tests fill the system to be tested with water or the operating
4-92 February 2000

fluid. The system is then sealed and pressure increased to approximately 1.5 times
operating pressure.
This pressure is held for a defined period. During the test, inspections are conducted
for visible leaks as well as monitoring pressure drop and make-up water additions. If
the pressure drop is out of specification, the leak or leaks must be located and repaired.
The principle of hydrostatic testing can also be used with compressed gases. This type
of test is typically called an air drop test and is often used to test the integrity of high-
pressure air or gas systems.
f. Eddy Current Testing—Detection of surface and shallow sub-surface defects. Also

known as electromagnetic induction testing. Eddy Current testing provides a portable
and consistent method for detecting surface and shallow sub-surface defects. This
technique provides the capability to quickly inspect metal components for defects or
homogeneity. By applying rapidly varying AC signals through coils near the surface of
the test material, eddy currents are induced into conducting materials. Any
discontinuity that affects the materials electrical conductivity or magnetic permeability
will influence the results of this test. Component geometry must also be taken into
account when analyzing results from this test.
A set of magnetizing coils are used to induce electrical currents (eddy currents) into the
component being tested. The induced currents produce magnetic fields, which are then
detected by a set of sensing coils. Typically the two sets of coils are combined into a
single probe. In some systems Hall effect devices are used instead of sensing coils.
The frequency of the AC signal used (5 to 10M Hz) determines the depth of penetration
through the material for the eddy currents. Lower excitation frequencies increase the
penetration depth and improve the effectiveness in detecting deeper defects. Higher
frequencies are utilized to enhance detection of surface defects. Analysis equipment
senses several parameters including magnitude, time lag, phase angles and flow
patterns of the resulting magnetic fields. Automated analysis methods reduce the
reliance on operator experience for consistent results.
4.7.2 Location & Intervals

Prior to implementing an NDT program, a formal plan should be developed detailing the type of
technique to be used, location, frequency, number and orientation of samples, information to be
gained form each sample and failure mode that each sample addresses. This plan will point out
excessive testing and omissions from the NDT Program. Two of the more difficult variables to
address are location and interval (time period) between inspections.
4.7.2.1 Intervals
When establishing sample intervals or frequency, several factors must be weighed. Operating
cycle of the system, historical failure rate, type of container material, type of contained
substance, chemistry control, major corrosion mechanisms, expected corrosion rate, erosion
mechanisms, expected erosion rate, proximity of existing material to minimum wall thickness,
February 2000 4-93

consequences of system breach and type NDT techniques applicable to the situation will affect
the inspection interval (Table 4–2). Other factors may enter into consideration, if warranted.
American Petroleum Institute (API 570) recommends the following criteria for establishing
intervals for NDT inspection.
Piping Circuit Thickness External Visual

Classification Measurements Inspection
Class 1 5 Years 5 Years

Injection Points 3 Years By Class
Soil-to-Air Interfaces — By Class
Table 4–2. Recommended Maximum Inspection Intervals (API 570)
In-place corrosion rates in conjunction with remaining life calculations.
Remaining life = tactual - tmin

annual corrosion rate
Remaining life = Number of years until thickness reaches minimum

tactual = Actual minimum thickness at time of most recent inspection
tmin = Minimum allowable thickness for the limiting section
Piping service classification where Class 1 has the highest potential of resulting in an immediate
emergency and Class 3 has the lowest potential if a leak were to occur.
Relevant regulatory requirements must be taken into account when determining NDT inspection
intervals. With the multitude of professional codes and government regulations this section will
not attempt to cover specific regulations. Many government regulations provide sufficient
leeway for the experts within an organization to set intervals in accordance with technically
sound methods. Some regulations simply require a technically sound plan that the organization
follows.
Before accepting what seems like an unreasonable interval simply in the name of regulatory
compliance, investigate the document that originates the requirement. In industry, many
regulatory requirements have been needlessly made more stringent by the philosophy, “If a little
is good, a lot must be better.” In an effort to avoid falling afoul of regulatory inspectors,
inspection costs were significantly increased without a corresponding increase in plant safety or
4-94 February 2000

reliability. Investigate basic requirements; if these are unclear ask the originating agency for
clarification of their expectations.
After the base inspection intervals have been established based on corrosion rate, class and
regulatory requirements; specific system intervals can be modified based on actual conditions,
historical data and operating parameters. Evaluate intervals based on operating conditions,
previous history, current inspection results or other indications of other than normal conditions.
By conducting statistical analysis on historical NDT results and failure rates, intervals can be
refined with a higher level of confidence. Pareto and Weibul analysis techniques can be applied
to indicate systems where unusual failure rates are occurring. Coupons can be utilized to provide
specific information on the corrosion rate, allowing further refinement of inspection intervals.
Process parameters can be used as a “trigger” for specific NDT inspections (Figure 4–8). As
thermodynamic properties change, they can provide an indication of increased corrosive product
deposits. Analysis of fluids transported within the system can also indicate changes in corrosion
activity allowing NDT inspection schedules to be appropriately adjusted. Procedures for
addressing adverse events such as over-pressurization and out of specification temperatures
should include the requirement for more frequent or immediate NDT inspections. Details of
type, location, parameter of concern and acceptable value should be indicated to facilitate a safe
and expeditious recovery from the incident.
4.7.2.2 Locations
The following should act as guidelines for locating NDT sampling points:
• Abrupt changes in direction of flow (elbows) and changes in pipe diameter will
cause turbulence that may accelerate many corrosion mechanisms.
• Presence of “Dead-Heads” that can create turbulence or stagnant areas where
material may accumulate and set up corrosion cells.
• Junctions of dissimilar metals. Galvanic corrosion is prevalent in these areas
unless specific steps are taken to prevent it.
• Stressed areas, welds, high stress fasteners and areas that undergo cyclic
temperature, pressure, or flow changes.
• Some applications may warrant specifying top, middle or bottom of pipe or areas
where more than one phase of a substance is present.
• Areas where accelerated corrosion/erosion mechanisms have been identified.
• Areas susceptible to cavitation.
February 2000 4-95

NDT Inspection Program
4-96
Development Process
Establish Determine Can These

Outline Define Define Define What Failure
Establish Historical Modes Modes
Define Current Engineering System System Modes Are
Equipment Failure & Current Be More
System NDT Parameters Failure Overpressure Not
Criticality Corrosion NDT Effectively
Program of System Modes Protection Addressed?
Rates Addresses Addressed?
Compare
Determine Define Alert Define Alarm Minimum Calculate
Determine Define Corrosion
Methods To Determine Corrosion Corrosion Rate Interval Is Calculate Maximum
Expected Acceptable Rates Wiith
Address Inspection Rate (Prompts Time To Reach Material Life Allowable
Corrosion Corrosion NDT
These Locations (Prompts Corrective Repeatable Remaining Working
Rate Rate Repeatable
Failure Modes Inspections) Action) Sensitivity Pressure
Sensitivity
Establish Establish
If Regulatory Investigate Establish Define
Inspection Evaluate Effect Process Formalize &
Establish Requirement Other Methods Inspection Axis, Establish Financial
Interval Based Of P & T Cycles Indicators, Document
Regulatory Most Stringent, To Meet Number of Control Impact Of
On 80% Of Or Abnormal Coupons & NDT Plan &
Requirements Meet Regulatory Positions Each Group Program
Shortest Transients Chemistry Process
Requirement Requirements Location Modifications
Interval Sampling
Figure 4 – 8. Inspection Program Development

Determine Document
Establish Information NDT
Feedback To Be Gathered Requirements
System When Abnormal in Operating
Corrosion Occurs Procedures
February 2000
4.7.3 Applications
a. Radiography—Radiographic techniques are readily applicable to metal components
including weld deposits. Specialized applications for plastics or composite materials
are possible, though typically these materials are not most economically inspected
with radiography. For thick cross-sections, radiography is often the only reliable
method for inspection.
b. Ultrasonics—UT techniques are readily applicable to metal components including

weld deposits. Specialized applications for plastics or composite materials are
common. Whenever possible, UT is a preferred method over radiography for in-place
applications, due to expense and safety precautions required by radiography. UT is
especially useful since it only requires access to one surface of the material.
Ultrasonic techniques provide excellent penetrating power for thick cross-sections.
c. Magnetic Particle—MT techniques are applicable only to materials that conduct

electric current and magnetic lines of flux. Only shallow defects are detectable with
MT inspection. Typically these techniques are most effective on welded areas. The
speed of testing allows multiple inspections to be conducted along different axes to
detect defects in different orientation planes.
d. Dye Penetrant—DP inspections are applicable for any non-porous material that is
chemically compatible with the dye and developer. This is the simplest NDT
technique in which to gain proficiency.
e. Hydrostatic Testing—Hydros test the integrity of pressure boundaries for
components and completely assembled systems that contain pressurized fluids or
gases. Identification of defects that penetrate the entire pressure boundary is the
primary application for hydrostatic testing.
f. Eddy Current—Eddy current techniques are used to detect internal defects such as
cracks, seams, holes or laminations separation on both flat sheets and more complex
cross-sections as well as monitoring the thickness of metallic sheets, plates and tube
walls. Portable systems are used extensively in the condition monitoring of installed
heat exchanger and chiller tube wall thickness. Where coating thickness is an
important factor, there is sufficient difference in electrical or magnetic properties
between the base material, and the coating. Eddy Current Testing can determine the
actual coating thickness. In more production-oriented applications, installed systems
can determine material composition, uniformity and thickness of materials being
produced.
4.7.4 Limitations
a. Radiography—Effective use of radiography mandates expensive equipment,
extensive safety precautions and skilled technicians to interpret the images.
Expensive tracking and security for radiation sources is mandatory. Safety
precautions often demand evacuation of areas adjacent to the piece being examined or
installation of extensive shielding.
February 2000 4-97

Even with these limitations, radiography is often the most effective method of
assuring integrity of critical welds, structural members and pressure boundaries. As
material thickness increases, radiography is often the only acceptable method to
achieve a 100% penetration.
b. Ultrasonics—UT techniques are one-dimensional. Unless special techniques are

applied, defects that parallel the axis of the test will not be apparent. Components
constructed using laminate techniques or layered construction present special
problems for UT techniques, since the boundary between each layer may be
interpreted as a defect. The thicker the layers of base material, the more likely UT
will provide usable results.
c. Magnetic Particle—MT techniques are applicable only to materials that conduct

electrical current and influence magnetic lines of flux. The difference in the influence
of the lines of flux between base material and the defect is the basis for MT
inspection. Only small areas (30 square inches) between the two electrodes can be
inspected.
Surface preparation is important, though not as critical as with UT. Consistent

electrode contact is critical. Loose contact will weaken the magnetic lines of flux to
the point where the influence of a defect may not be visible in the filing pattern.
Operator skill is important, though this is a relatively simple technique. No historical
record is produced for each test, unless specific steps are taken to photograph the
result of each test.
d. Dye Penetrant—Minute surface discontinuities such as machining marks will

become readily apparent. The inspector must be trained to distinguish between
normal surface discontinuities and defects that must be repaired. The dye and
developer are usually sprayed or painted on the piece to be inspected, so over-spray
and protection of internal surfaces are prime concerns for systems with stringent
chemistry and cleanliness control. Product cleanliness standards may prohibit the use
of DP inspection.
e. Hydrostatic Testing—Cleanliness and chemistry control of the fluid must be

consistent with the operating standards of the system. Close attention should be given
to controlling system thermodynamic parameters during the test to prevent over-
pressurization of the system. Over-pressurization could lead to unintended damage to
the system. Individual component hydros do not assure system integrity. A final
hydro of the completed system is used to assure the integrity of the assembled
system’s pressure boundary.
Hydros will not identify defects that are present, but have not completely penetrated a
pressure boundary. The pressure applied to the system is generally not sufficient to
enlarge existing defects to the point of detection by the test. Hydrostatic testing
requires a pressure source capable of expeditiously filling and pressurizing the
4-98 February 2000

system, extensive instrumentation and monitoring equipment along with a sufficient

quantity of fluid to fill the system. A method of isolating pressure relief devices and
connecting the pressure source to the system must be provided.
f. Eddy Current—Eddy Currents tend to flow parallel to the surface to which the
exciting field is applied. Some orientations of laminar discontinuities parallel to this
surfaces tend to remain undetected by this method. Eddy Current Testing will not
penetrate deeply into the material of interest, so it is limited to shallow sub-surface
and surface defects.
4.8 Photography
Videotaping is often used to record complex machines during operation. The tape is played back
at a slow speed in order to what is happening. This is especially good tool for analyzing and
troubleshooting packaging machines.
a. Monitor - Broadcast industry quality is recommended.

b. VCR - A unit with 4 heads and shutter control to allow tape movement one frame at a
time. This is critical to viewing slow motion. It also is capable of recording and
playing back in Super VHS that allows for clearer recordings.
c. Camera - Minimum 10 - 1 zoom lens, low light capability, Super VHS capability and
a shutter speed of at least 1000.
d. Lights -The stand alone Tungsten work lights are recommended.
e. Digital Camera – Sufficient memory to store twenty pictures. The highest resolution
available is recommended.
f. Approximate Cost - $2,500
February 2000 4-99

4-100 February 2000

Chapter 5—RCM Requirements during Facilities Acquisition
This chapter discusses RCM requirements during the acquisition stage of the facilities life cycle;
i.e., during facilities planning, design, and construction.
5.1 Planning
Early in the planning of a new facility, consideration must be given to the extent RCM analysis
and PT&I techniques will be used to maintain the facility and its equipment. This is likely an
issue that crosses organizational lines (i.e. between operations, maintenance and engineering)
which should be addressed in the SOP with prior commitment from managers in those
organizations. The fundamental determination is the amount of built-in condition monitoring,
data transfer, and sensor connections to be used. It is more economical to install this monitoring
equipment and connecting cabling during construction than later. Planning, designing, and
building in the condition monitoring capability ensures that it will be available for the units to be
monitored. Continuously monitored equipment tied into performance analyzers permits
controlling functions and monitoring degradation. In the future, on-line monitors will become
increasingly capable and important. Installed systems also reduce manpower requirements as
compared with collecting sensor data with a portable data collector. However, for many uses,
portable condition monitoring equipment does provide the advantages of lower cost and
flexibility of application as compared with post-acquisition installed systems.
5.2 Design
The following should be considered during the design phase:
5.2.1 Maintainability and Ease of Monitoring

In recent years great strides have been made in designing new equipment to ensure a high level
of reliability. By extending this approach to the maintainability and ease of monitoring of
equipment during design, one further enhances reliability and ensures improved maintainability
for the life of the equipment.
a. Maintainability factors that are within the control of the designer are:
1. Access - Equipment, its components, and facilities should be accessible for mainte-
nance.
2. Material - Choose materials for durability, ease of maintenance, availability, and

value (optimal cost vs. special requirements trade-offs).
3. Standardization - Minimize use of special or one-of-a-kind materials, fittings, or

fixtures. Maximize commonality of equipment component parts. Choose standard
equipment for multiple uses where feasible.
February 2000 4-101

4. Quantitative Maintenance Goals - Use quantitative measures of maintenance (i.e.,

mean-time-between-maintenance (MTBM), maintenance downtime (MDT), etc.) to
set goals for maintainability which will influence design.
b. Ease of Monitoring factors within the control of the designer are:
1. Access - Provide clear access to collect equipment condition data with portable data
loggers or fluid sample bottles.
2. On-line Data Collection - Installed data collection sensors and links (wire, fiber
optics, or radio frequency (RF) links are possible) may be justified for high-priority,
high-cost equipment or inaccessible equipment.
3. Metrics - Management, or performance indicators (Metrics) are discussed in Chapter

10. For an RCM program, the Metrics and the analysis methods are incorporated into
the system design. Often the performance parameters monitored for equipment or
system control may be used to monitor equipment condition.
4. Performance Measures - RCM performance measures such as operating time or

equipment loading are directly equipment related. The data to be used and the
collection method are incorporated into the system design.
5.2.2 Technology Review

As mentioned earlier, the technology review should be a part of the SOP for new facilities and/or
equipment design and acquisition and should address the following six areas:
a. PT&I Review - Conducting a PT&I technology review at an early stage of the design is
necessary to establish which technologies are to be used in the RCM program.
b. Maintenance Review - A continuing review of other maintenance programs for new and
emergent predictive technologies assists in keeping the program current by incorporating
the latest technological developments.
c. Feedback - Update or improve the design based on feedback, prior experience, and
lessons learned.
d. Scope of Work - Clearly establish in the Architect & Engineering (A&E) contract scope
of work that RCM maintainability and ease of monitoring requirements must be met.
e. Qualification - Contractor qualifications should provide for a demonstration of

familiarity and/or understanding of the PT&I technologies planned for the RCM program.
4-102 February 2000

f. Specifications and Drawings -
1. The designer has a major impact on the life-cycle cost of the equipment by
incorporating the RCM lessons learned from the history of similar or identical
equipment.
2. The design specifications should address the use of condition-based maintenance in

lieu of interval-based maintenance and its effect on manufacturer’s warranties.
3. Specifications for equipment procurement should incorporate maintainability and

ease of monitoring requirements. Maintainability requirements should be specified in
terms of an appropriate combination of measurements. The attainment of these
requirements is an important aspect of equipment performance.
4. Construction contracts should specify the type of acceptance testing to be performed

on building materials and equipment prior to shipment to the building site. The
designer also should specify the PT&I technologies to be used and the related
acceptance criteria as part of the post-installation acceptance testing for all collateral
equipment and structures and for determining if a building is ready for occupancy.
5.3 Construction
During the construction phase, a major concern is to monitor the progress and quality of
construction to ensure that the planning and design work from earlier phases is effectively
implemented. This includes monitoring for conformance to specifications, drawings, bills of
material, and installation procedures. The following important steps should be taken during
construction:
a. Training—The training of personnel in the use of PT&I technologies and equipment

should start during construction.
b. RCM Analyses—It is during this phase that RCM analyses are done, the maintenance
program tasks should be chosen, and maintenance procedures and instructions should be
written.
c. O&M—Operations and maintenance personnel should take advantage of the construction

phase to become familiar with the details of construction which will no longer be easily
accessible after the facility is completed.
d. Inspectors—The construction inspectors should assure that the construction contractor

properly installs, aligns, and checks the equipment in accordance with the contract
specifications and the equipment manufacturer’s recommendations. Incorrect installation
can void the manufacturer’s warranty and cause early equipment failure.
February 2000 4-103

e. Equipment—When equipment is specified by performance rather than proprietary name

(which is preferable), the contractor should be required to submit catalog descriptions of
the equipment he intends to provide for approval by the Government. The equipment
should be approved by the Government (including the RCM technologists) to ensure that
it satisfies the requirements of the contract specifications. If the contract specifications
require that the contractor establish a vibration and thermographic baseline for the
equipment, the Governmant should ensure that this is done and that the baseline
information is properly documented and turned over to the Government with the
equipment technical manuals and other information required from the contractor.
5.4 Maintenance and Operations (M&O)

How the facility and its equipment will be operated and maintained must be considered during
the planning, design, and construction phases. During these phases, M & O needs are best
served by carefully and realistically identifying and defining the PT&I requirements. Although
the performance of M & O tasks occur during the operations stage of the life cycle of the
equipment or facility, some preparatory activities may be carried out during the latter part of the
acquisition stage. These activities include personnel selection, PT&I training, procedure
preparation, review of specifications, and the collection of nameplate data.
4-104 February 2000

Chapter 6 - RCM Considerations during Facilities Operation
This chapter discusses RCM requirements during the operational stage of the facilities life cycle
(maintenance and operations).
6.1 RCM Program Data

The need to maintain an adequate level of funding is a continuing requirement during the life
cycle of a facility. As a result, there is a recurring need to input RCM program data into an
Annual Work Plan (AWP) and/or other budgetary planning documents. To support these
periodic requirements, the collection of data for justification purposesshould not be left to chance
or to the last minute.
It is important for RCM maintenance costs, cost avoidance, and program savings to be
documented as they occur. A good Computerized Maintenance Management System (CMMS)
has the capability to track this information. Direct maintenance program savings are usually
apparent, but maintenance personnel must become attuned to recognizing and documenting the
less obvious “costs avoided.” This data also becomes a key part of the Continuous Improvement
(CI) process in that it is the feedback that reinforces the behavior created by the RCM
organization.
One use of maintenance data is in tracking the maintenance burden; i.e., the man-hours and/or
labor costs expended for all types of maintenance on a particular equipment. By identifying the
equipment on which maintenance effort is spent and categorizing the type of maintenance (i.e.,
RM, PM or PT&I), the maintenance burden may be allocated to end use. With labeled
maintenance man-hour expenditures, both the high burden items and the distribution of the
burden within the facility can be tracked over time. The use of Pareto analysis, or some other
method of prioritization of maintenance resource assignment, will permit the easy identification
of areas that demand attention from the standpoint of maintenance effectiveness or the need for
modification to improve reliability. As the intensive PT&I efforts take hold, the effects on
themaintenance burden can be analyzed to determine their costs and relative values, especially as
increased availability and improved quality impacts each activity.
The task of maintaining and updating drawings and specifications to keep facility documentation
abreast of the modifications and alterations should not be neglected. If not already part of the
Standard Operating Procedures (SOP), it should be added. The effectiveness of the facility and
the RCM program will reflect the degree to which this updating is accomplished.
6.2 Maintenance Feedback

During the life of the facility and its equipment, a continual effort is required for modifications
and alterations to the design as operators and maintenance personnel gain experience with the
facility. Sometimes these changes result from an expanded or modified facility mission. As the
facility matures, new methods and tools become available to accomplish the mission and tasks in
a more efficient or cost-effective manner. This need for changes and modifications must be
February 2000 6-105

documented and returned to the designers as feedback. Again, this needs to be a part of the
operating culture and should be added to the SOP.
An important function of feedback during the life cycle of any facility is to improve and optimize
the performance of the equipment. The RCM organization can be tasked with this function and,
if done properly, will become a crucial asset to future designs. As shown in Figure 6–1, design
improvements from one generation of equipment to the next can have a significant effect on
reliability. The feedback that the designer integrates into each successive generation yields
lower overall failure rates and extended equipment life. These improved characteristics reduce
maintenance costs as well, thus contributing to a lower life-cycle-cost, which is one of the goals
of the RCM and Continuous Improvement process.
6.3 Maintenance and Operations (M&O) Considerations

The following are RCM considerations during the M&O activity:
a. Labor Force—The RCM program requires a labor force with the special skills
necessary to accomplish the program’s reactive, preventive, and PT&I tasks
successfully. The quality of the maintenance accomplished is reflected in the equipment
post-maintenance, infant mortality rate. The quality of maintenance is influenced by: 1)
the skill of the maintenance technicians, 2) their workmanship, 3) the quality of
supporting documentation and procedures, and 4) the technologies in use.
b. System Experts—The responsibility for condition monitoring, predictive analysis, and

maintenance planning should be assigned to someone not subject to random or frequent
reassignment. To maintain continuity of effort, to gain experience for a single
individual or group, and to ensure a consistent technical approach, a single person
should be assigned maintenance oversight responsibility for a given equipment or group
of similar equipment.
The involvement of a single person in all maintenance actions for the equipment or
system(s) for which they are responsible is the heart of the system expert concept and is
an excellent way to provide continuity of experience and expertise with regard to the
equipment and systems. The system expert is the person responsible for monitoring and
analyzing the maintenance data for an assigned equipment or system. The system expert
should receive all the related data, work requests, and test documents for review,
analysis, and filing. The system experts designated to maintain expertise and provide
continuing oversight, analysis, and continuity for designated facility systems or
equipment. The system expert concept results in a significant contribution to better
overall management of facility maintenance and provides the critical elements of the
organization’s memory and its analysis.
6-106 February 2000

1st Generation Equipment

Bathtub Characteristic
Pcond
Infant Random Wearout
Mortality Failures
Time
2nd Generation Equipment

Saucer Characteristic
Life Extension from
Impoved Maintenance
Tasks and Proactive
Maintenance
Pcond
Time
Infant
Mortality Reduced by
Less Maintenance and
Better Commissioning
Figure 6 – 1. Design Improvements through Maintenance Feedback
The system expert is not intended to replace or supplant the technical expertise normally
found within the design organization of the original equipment manufacturer (OEM), the
facility, or at the Center or NASA headquarters. The system expert is expected to be a
member of the facility maintenance team who is conversant with the maintenance
history of their assigned equipment and systems. The system expert is also involved
with integrating maintenance support from facility resources outside of the normal
maintenance organization.
c. Training—Training plays a major role in reaching and maintaining the required RCM
workforce skill level. The training is both technology/equipment specific and of a more
general nature. Management and supervisory personnel benefit from training which
presents an overview of the RCM process, its goals, and methods. Technician training
includes the training on specific equipment and technologies, RCM analysis, and PT&I
methods.
February 2000 6-107

Root Cause/
Maintenance Technology/
Position/Title RCM/PT&I Predictive
Overview Equipment
Analysis
Managers/
X X X
Supervisors
System
X X X X
Experts
Maintenance
X X X X
Technicians
Support
Personnel X
(Logistics)
Table 6–1. Maintenance Training
d. Equipment—During the operation of the facility and its equipment, a Continuous

Improvement program should be in place. The need for equipment modifications and
alterations is documented by feedback from the operators and maintenance personnel.
An important function of feedback during the life of the facility is to improve the
performance of the facility and its equipment. The M&O-to-designer linkage is crucial
in this improvement process. As shown in Figure 6–1, design improvements from one
generation of equipment to the next have a significant effect on operability,
maintainability and reliability.
e. Maintenance History—An important function of the CMMS is to collect, organize,

display, and disseminate maintenance data. The CMMS provides the facility’s
maintenance history, which is critical to the success of the RCM program because:
1. It contains information to establish whether an age-reliability relationship (wear-

out) exists for equipment, and if so, what is the critical failure-onset age.
2. It contains the data that is analyzed to trend and forecast equipment failure.
3. It forms the basis for analysis of long-term equipment and system performance
trends.
4. It provides the statistics used to determine the failure rates, which influence spare
part stock levels.
5. It contains test results, performance data, and feedback information used to

improve equipment performance and document equipment condition.
6-108 February 2000

f. Procedural Documentation—For a maintenance organization to be truly world class, it

must perform reactive maintenance expeditiously and correctly. Complex repair tasks
should be planned in advance. The use of maintenance planners to generate
maintenance work orders, which include detailed procedures, repair parts, tools,
maintenance personnel training, and specific test procedures, is part of a good work
order system for a complicated or critical repair. This detailed work planning has been
proven to be vital by quality maintenance organizations. Work preparations ensure
smooth repair with few surprises and greatly reduce the incidence of “infant mortality”
which often accompanies the difficult repairs. The lessons learned from each repair are
included in the equipment history for future reference. As a maintenance organization
gains experience, it builds a file of work orders that may be reused repeatedly.
The use of standard procedures in PT&I ensures that data is collected in a consistent and
comparable manner without being dependent on the experience of the collecting
technician. Improvements in data collection techniques can be applied to all similar
collection efforts by modifying the standard procedures.
February 2000 6-109

6-110 February 2000

Chapter 7 - RCM Contract Clauses
There are several basic contract purposes involved in the facility and equipment life cycle. They
are as follows:
• Architect/Engineering (A&E) Contracts

• Construction Contracts
• Equipment Procurement Contracts
• Maintenance and Operation Contracts
There is a need for RCM-related clauses in each of these types of contracts. Standard clauses
have been developed for this purpose.
These contracts occur during the following life cycle phases:
Life Cycle Phase Contract Type

Planning None
Design A&E
Construction Construction
Maintenance and Operations Equipment Procurement
Maintenance and Operations
This chapter contains recommended standard RCM contract clauses. Clauses are grouped by
equipment and the applicable technology. Tables 7–11 through 7–14 identify and cross-
reference the applicability of each RCM contract clause, component, and type of contract for
each phase of the contract.
The following describes the applicability of each table:
A&E Contracts Table 7–11

Construction Contracts Table 7–12
Equipment Procurement Contracts Table 7–13
Maintenance and Operations Contracts Table 7–14
The applicable RCM contract clause and criteria should be included in all Requests for Proposals
(RFPs), Requests for Quotations (RFQs), and in the contracts themselves.
The clauses may be used without modification; however, they will have to be renumbered to fit
the organization of the specification in which they are used.
February 2000 7-111

7.1 General Contract Clauses

This section contains the standard contract clauses for all of the phases in the facility life cycle.
The specific clauses to be used in each phase are suggested in paragraphs 7.2 through 7.5.
For example, the vibration data listed in paragraphs 7.1.7 through 7.1.8 should be included in
contract specifications if vibration analysis is to be performed as part of the RCM program.
7.1.1 Measurements and Measurement Data

When measurements or surveys are required by a contract clause, the contractor shall furnish to
the procuring organization the following information concerning the equipment used to make the
specified measurements:
a. Test Equipment—List of all test equipment used, including manufacturer, model

number, serial number, calibration date, certificate of calibration, and special personnel
qualifications required.
b. Equivalency—If the contractor uses an equivalent test or procedure to meet the

requirements of the contract specification, the contractor shall provide to the procuring
organization proof of equivalency.
7.1.2 Bearing Information

a. Drawings—The contractor shall provide to the procuring organization section drawings
that show the component arrangement for all rotating equipment supplied under the
contract. The section drawings shall accurately depict the bearing support structural
arrangement, be drawn to scale, and show the dimensions to the centerline of all rotating
shafts.
b. Bearing Data—The contractor shall provide to the procuring organization the bearing
manufacturer and part number for all bearings used in all rotating equipment supplied
under this contract. The information shall be included on the sectional drawings for each
bearing location.
c. Operating Data—The required equipment data the contractor shall provide the
procuring organization under this contract shall include the operating speed for constant
speed units and the normal operating speed range for variable speed equipment.
7.1.3 Gearbox Information

The contractor shall provide to the procuring organization the type and number of teeth on each
gear used in the gearbox and the input and output speeds and gear ratios. This information shall
be included on the sectional drawings which must be to scale and be specific to gear location.
7-112 February 2000

7.1.4 Pumps
The contractor shall provide to the procuring organization the following information on all
pumps supplied under the contract:
• Number of pump stages

• Number of pump vanes per stage
• Number of gear teeth for each pump gear
• Type of impeller or gear(s)
• Rotating speed
• Number of volutes
• Number of diffuser vanes
7.1.5 Centrifugal Compressors

centrifugal compressors supplied under the contract:
• Number of compressor sections

• Number of blades per section
• Number of diffusers
• Number of vanes per diffuser
• Number of gear teeth on drive gear
• Number of driven shafts
• Number of gear teeth per driven shaft
• Rotating speed of each rotor
7.1.6 Fans
The contractor shall provide to the procuring organization the following information on all fans
supplied under the contract:
• Type of fan or blower

• Number of rotating fan blades/vanes
• Number of stationary fan blades/vanes
• Rotating speed(s)
February 2000 7-113

The contractor shall provide to the procuring organization the following additional information if
the fans/air handlers are belt driven:
• Number of belts
• Belt lengths
• Diameter of the drive sheave at the drive pitch line
• Diameter of the driven sheave at the drive pitch line
For all fans supplied under the contract, the contractor shall ensure sufficient access to the fan is
present to allow for cleaning and in-place balancing of the fan.
7.1.7 Vibration Monitoring

The contractor shall provide to the procuring organization the following information for all
equipment where a vibration specification is included in the contract.
7.1.7.1 Instrumentation and Sensors

The contractor shall use the type of instrumentation and sensors specified. For example, for a
3,600 RPM machine an accelerometer with a sensitivity of 100 mV/g and a resonant frequency
of at least 15,000 Hz is required. A rare earth super magnet and a sound disc shall be used in
conjunction with any vibration data collector which has the following characteristics:
• A minimum of 400 lines of resolution.

• A dynamic range greater than 70 dB.
• A frequency response range of 5Hz-10kHz (300-600,000 cpm).
• The capability to perform ensemble averaging i.e., average the data collected.
• The use of a hanning window.
• Autoranging.
• Sensor frequency response shall conform to Figure 7–1.
The contractor shall provide to the procuring organization narrowband spectral vibration data for
all machines as follows:
a. For machines operating at or below 1,800 RPM, the frequency spectrum provided shall
be in the range of 5 to 2,500 Hz.
b. For machines operating greater than 1,800 RPM, the frequency spectrum provided shall
be in the range of 5 to 5,000 Hz.
c. Two narrowband spectra for each point shall be obtained in the following manner:
7-114 February 2000

Transducer Response Specification

Transducer response curve must fall within the shaded area.
Amplitude Linearity: Maximum deviation from linearity

shall be less than 10% for vibration amplitudes in the
range between 500 and 100,000 microinches per second rms.
Transducer Sensitivity of the transducer as matched with the sensing 3.5 db

Sensitivity system shall be specified within plus or minus 5%.
Velocity Units 1 db
50 Note: Figure 3 of ANSI/AFBMA 8,000 10,000

Std. 13-187
Frequency In Hz
Figure 7-1. Transducer Response
1. For all machines regardless of operating speed, a 5 to 500 Hz spectrum with 400 lines
of resolution shall be used to analyze balance, alignment, and electrical line frequency
faults.
2. An additional spectrum of 5 to 2,500 or 5 to 5,000 Hz shall be acquired for machines

operating at or below 1800 RPM or greater than 1,800 RPM, respectively. This
higher frequency range allows early detection of rolling element bearing, gear rotor
and stator problems.
3. The contractor shall report vibration data in velocity (inches/second). If proximity

probes are installed, the contractor shall acquire and analyze vibration and phase data.
4. The contractor shall ensure that the equipment provided meets the following
acceptable vibration amplitudes for each machine:
(a) Developing Vibration Criteria—Specific vibration criteria are provided in this

guide where possible. Where specific criteria are not provided the following
procedure is recommended for the guide user for use in developing the vibration
criteria:
(1) Obtain nameplate data.
February 2000 7-115

(2) Obtain vibration spectra on similar machines. Differences in baseplate

stiffness and mass will affect the vibration signature.
(3) Calculate all forcing frequencies, i.e., imbalance, misalignment, bearing

defect, impeller and/or vane, electrical, gear, belt, etc.
(4) Construct a mean vibration signature for the similar machines.
(5) Compare this mean vibration signature to the specifications and guidelines
provided in this guide.
(6) Note any deviations from the guidelines and determine if the unknown
frequencies are system related; e.g., a resonance frequency from piping
supports.
(7) Collect vibration data on the new component at the recommended positions.
(8) Compare the vibration spectrum with the mean spectrum determined in step
(5) above as well as with the criteria and guidelines provided in this guide.
(9) Any new piece of equipment should have a vibration spectrum which is no
worse than a similar unit of equipment which is operating satisfactorily.
(b) Vibration Analysis of New Equipment—For all large or critical pieces of

equipment assembled and run at the factory prior to shipment, a narrowband
vibration spectrum should be acquired at the locations listed in Section 7.1.8 of
this guide while the equipment is undergoing this factory performance testing. A
baseline or reference spectrum should be retained for comparison with the post-
installation vibration check. Equipment failing the vibration criteria should be
rejected by the procuring organization prior to shipment.
Vibration tests are recommended under the following situations if the equipment
fails the initial test and/or if problems are encountered following installation:
• Motor cold and uncoupled.

• Motor hot and uncoupled.
• Motor and machine coupled, unloaded and cold.
• Motor and machine coupled, unloaded and hot.
• Motor and machine coupled, loaded and cold.
• Motor and machine coupled, loaded and hot.
7-116 February 2000

A significant change in the vibration signature could indicate a problem with

thermal distortion and/or bearing overloading due to failure of one of the
bearings to float.
(c) Vibration Criteria for Electric Motors
(1) General—All motor vibration spectra should be analyzed at the following

forcing frequencies:
• One times running speed (1X) for imbalance.
• Two times running speed (2X) for misalignment.
• Multiples of running speed (NX) for looseness, resonance, plain

bearing defects.
• Electric line frequency and harmonics (60 or 120 Hz for AC motors)

for stator and rotor problems.
The following is a list of rolling element bearing frequencies:
• Outer race defect frequency
• Inner race defect frequency
• Ball defect (ball spin frequency)
• Fundamental train frequency
Plain or journal bearings indicate faults at harmonics of running speed and

at the frequency corresponding to 0.4-0.5 of running speed.
Other sources of vibration in motors are dependent on the number of motor

rotor bars and stator slots, the number of cooling fan blades, the number of
commutator bars and brushes, and on the SCR firing frequencies for
variable speed motors.
Broken rotor bars will often produce sidebands spaced at two times the slip
frequency. The presence of broken rotor bars can be confirmed through the
use of electrical testing.
(2) Balance—The vibration criteria listed in Table 7–1 are for the vibration
amplitude at the fundamental rotational frequency or one times running
speed (1X). This is a narrowband limit. An overall reading is not
acceptable.
February 2000 7-117

Motor Speed Maximum Vibration Maximum Displacement

(RPM) (in/sec, Peak) (mils, Peak-to-Peak)
900 0.02 0.425

1200 0.026 0.425
1800 0.04 0.425
3600 0.04 0.212
Table 7–1. Motor Balance Specifications
(3) Additional Vibration Criteria—All testing should be conducted at normal

operating speed under full load conditions. Suggested motor vibration
criteria are provided in Table 7–2. In addition, Appendix E contains criteria
for common machines and an example of how to calculate criteria.
Frequency (X RPM) Maximum Amplitude

Motor Component (in/sec Peak)
0.4 - 0.5 Not detectable
1X See Motor Balance Specifications
2X 0.02
Harmonics (NX) Not detectable
Roller Element Bearings Not detectable
Side Bands Not detectable
Rotor Bar/Stator Slot Not detectable
Line Frequency (60 Hz) Not detectable
2X Line Frequency (120 Hz) 0.02
Table 7–2. Motor Vibration Criteria
(4) Rewound Electric Motors—Due to the potential of both rotor and/or stator
damage incurred during the motor rewinding process (usually resulting
from the bake-out of the old insulation and subsequent distortion of the pole
pieces) a rewound electrical motor should be checked both electrically and
7-118 February 2000

mechanically. The mechanical check consists of post-overhaul vibration

measurements at the same location as for new motors. The vibration level
at each measurement point should not exceed the reference spectrum for
that motor by more than 10%. In addition, vibration amplitudes associated
with electrical faults such as slip, rotor bar, and stator slot should be noted
for any deviation from the reference spectrum.
Note: Rewinding a motor will not correct problems associated with thermal
distortion of the iron.
(5) General Equipment Vibration Standards
• If rolling element bearings are utilized in either the driver or driven

component of a unit of equipment (e.g., a pump/motor combination),
no discrete bearing frequencies should be detectable. If a discrete
bearing frequency is detected, the equipment should be deemed
unacceptable.
• For belt-driven equipment, belt rotational frequency and harmonics

should be undetectable. If belt rotation and/or harmonics are
detectable, the equipment should be deemed unacceptable.
• If no specific criteria are available, the ISO 3945 acceptance Class A

guidelines should be combined with the motor criteria contained in
Table 7–2 and used as the acceptance specification for procurement
and overhaul.
(6) Specific Equipment—Use the criteria shown in Table 7–3 on boiler

feedwater, split case, and progressive cavity pumps:
Maximum Vibration Amplitude

Frequency Band
(in/sec Peak)
0.06
Overall (10-1000 Hz)
0.05
1X RPM
2X RPM 0.02
Harmonics 0.01
Bearing Defect Not detectable
Table 7–3. Pump Vibration Limits
February 2000 7-119

(7) Belt Driven Fans—Use the criteria in Table 7–4 for belt-driven fans:
Maximum Vibration Amplitude

Frequency Band
(in/sec Peak)
Overall (10-1000 Hz) 0.15
1X RPM 0.1
2X RPM 0.04
Harmonics 0.03
Belt Frequency Not detectable
Bearing Defect Not detectable
Table 7–4. Belt-Driven Fan Vibration Limits
(8) Vibration Guidelines (ISO)—Table 7–5 is based on International

Standards ISO 3945 and should be used as a guideline (not as an absolute
limit) for determining the acceptability of a machine for service. The
vibration acceptance classes and ISO 3945 machine classes are shown in
Tables 7–6 and 7–7, respectively. Note that the ISO amplitude values are
overall measurements in inches/second RMS while the recommended
specifications for electric motors are narrowband measurements in
inches/second Peak.
5. The contractor shall collect vibration data at normal operating load, temperature, and
speed.
6. The contractor shall supply all critical speed calculations. In addition, the contractor
shall perform a check for machine resonance following installation and correlated
with all known forcing frequencies; i.e., running speed, bearing, gear, impeller
frequencies, etc.
7-120 February 2000

Ranges of Radial Quality Judgement for Separate

Vibration Severity Machine Classes
RMS Velocity
Range in 10-1000 Hz Class I Class II Class III Class IV
at the Range
Limits
mm/sec in/sec
0.28 0.28 0.011 A A A A

0.45 0.45 0.018 A A A A
0.71 0.71 0.028 A A A A
1.12 1.12 0.044 B A A A
1.80 1.80 0.071 B B A A
2.80 2.80 0.110 C B B A
4.50 4.50 0.180 C C B B
7.10 7.10 0.280 D C C B
11.20 11.20 0.440 D D C C
18 18 0.710 D D D C
28 28 1.10 D D D D
71 71 2.80 D D D D
Table 7–5. ISO 3945 Vibration Severity Table.
Class Condition
A Good
B Satisfactory
C Unsatisfactory
D Unacceptable
Table 7–6. Vibration Acceptance Classes
February 2000 7-121

Machine Classes for ISO 3945
Class I Small size machines to 20 HP
Class II Medium size machines (20-100 HP)
Class III Large machines (600-12,000 RPM)

400 HP and Greater
Rigid mounting
Class IV Large machines (600-12,000 RPM)

400 HP and Greater
Flexible mounting
Table 7–7. Machine Classifications
7. The contractor shall analyze all motor vibration spectra at the following forcing
frequencies and provide the results to the procuring organization:
• One times running speed (1X) for imbalance.

• Two times running speed (2X) for misalignment.
• Multiples of running speed (NX) for looseness, resonance, and plain bearing
defects.
• Electric line frequency and harmonics (60 or 120 Hz for AC motors) for stator
and rotor problems.
• Roller element bearing frequencies, when present.
7.1.8 Vibration Monitoring Locations

a. Monitoring Discs—For all rotating equipment provided under the contract, the
contractor shall install vibration monitoring discs using the following guidelines:
1. Sound discs shall be a minimum of 1" in diameter, manufactured of a magnetic

material, have a surface finish of 32 micro-inches RMS, and be attached by welding
or stud mounting. The contractor has the option of machining the equipment case in
order to achieve a flat and smooth spot which meets the same tolerances as the sound
disc if the equipment case is manufactured from a magnetic material.
2. The contractor shall ensure monitoring locations are positioned on structural

members. Installation of sound discs on bolted cover plates or other non-rigid
members are not acceptable.
7-122 February 2000

b. Centrifugal Pumps, Vertically Mounted—Sound discs shall be mounted in the radial

direction as close to the bearings as possible. Accelerometers shall be mounted to solid
structures and not on drip shields or other flexible structures. Mounting locations shall be
in line with each other, perpendicular to the pump discharge, and located at the free end,
at the coupled end of the motor and pump, and in the axial direction on the pump and
motor, if possible.
c. Centrifugal Pumps, Horizontally Mounted—Sound discs shall be mounted in the

horizontal and vertical planes radial to the shaft at the free and coupled ends of the motor
and pump as close to the bearings as possible. Accelerometers shall be mounted to solid
structures and not on drip shields or other flexible structures. Mounting locations shall be
in line with each other, perpendicular to the pump discharge and located at the free and
coupled end of the motor and pump, and in the axial direction on the motor and pump, if
possible.
d. Positive Displacement Pumps—Sound discs shall be mounted in the horizontal and

vertical planes radial to the shaft at the free and coupled ends of the motor and pump as
close to the bearings as possible. Accelerometers shall be mounted to solid structures and
not on drip shields or other flexible structures. Mounting locations shall be in line with
each other, perpendicular to the pump discharge, and located at the free end, coupled end
of the motor and pump, and in the axial direction on the pump and motor. An exception
may be granted if the pump is sump mounted.
e. Generators—The contractor shall install sound discs in the horizontal and vertical planes
on the free ends of the motor and generator bearing assemblies. Pedestal bearings
between the motor and generator should be monitored in the vertical direction radial to
the shaft. Thrust bearings shall be monitored in the axial direction.
f. Gear Boxes—The contractor shall install sound discs radial to the input and output shafts
in the horizontal and vertical directions. Additional discs shall be installed in the axial
direction as close to the input and output shafts as possible.
g. Compressors—The contractor shall install sound discs radial to the input and output
shafts in the horizontal and vertical directions. Additional discs shall be installed in the
axial direction as close to the input and output shafts as possible.
h. Centrifugal compressors may be monitored effectively in this manner. However,

reciprocating air compressors shall only be monitored for balance and alignment
problems.
i. Blowers & Fans—Motors on blowers and fans shall have sound discs installed in the
radial and axial directions as previously described. Fan bearings shall be monitored
radially in the vertical direction.
j. Chillers
February 2000 7-123

1. Centrifugal—The contractor shall mount sound discs in the horizontal and vertical
planes radial to the shaft at the free and coupled ends of the motor and compressor as
close to the bearings as possible. Accelerometers shall be mounted to solid structures
and not on drip shields or other flexible structures. Mounting locations shall be in
line with each other, perpendicular to the compressor discharge, and located at the
free end, at the coupled end of the motor and compressor, and in the axial direction on
compressor and motor.
2. Reciprocating—The contractor shall install sound discs radial to the input and output
shafts in the horizontal and vertical directions. Additional discs shall be installed in
the axial direction as close to the input and output shafts as possible.
7.1.9 Lubricant and Wear Particle Analysis

lubricants supplied in bulk or contained within equipment supplied under this contract:
a. Liquid Lubricants
Viscosity grade in ISO units
AGMA and/or SAE classification as applicable
Viscosity in Saybolt Universal Seconds (SUS) or centipoise at the standard temperature

and at designed normal operating temperature. The following formula should be used to
calculate SUS and absolute viscosity:
Z = pt(0.22s-180/s)
where: Z = absolute viscosity in centipoise at test temperature

s = Saybolt Universal Seconds
pt = specific gravity at test temperature
t = temperature (°F)
Changes in density can be calculated by the formula:
pt = pr-0.00035(t-60)
where: pr = specific gravity at the reference temperature (normally

60° F)
b. Grease Lubricants
National Lubrication and Grease Institute (NLGI) Number

Type and percent of thickener
7-124 February 2000

Dropping point
Base oil viscosity range in SUS or centipoise
The following formula shall be used to calculate SUS and absolute viscosity:
Z = pt(0.22s-180/s)
where: Z = absolute viscosity in centipoise at test temperature

s = Saybolt Universal Seconds
pt = specific gravity at test temperature
Changes in density can be calculated by the formula:
pt = pr-0.00035(t-60)
where: pr = specific gravity at the reference temperature (normally 60° F)

c. Lubricant Tests—The contractor shall draw lubricants and perform the lubricant tests
listed in Table 7–8 on all lubricants supplied by him and shall submit the results of the
tests to the procuring organization.
February 2000 7-125

Lubricant Tests
Testing Correlates When

Test For Indicates With Used
Total Acid No. (TAN) pH Degradation, oxidation, Visual, RBOT Routine

Total Base No. contamination
Rotating Bomb Oxidation Anti-oxidants Lubricant resistance to TAN Periodic (long

Test (RBOT) remaining oxidation term)
Solids Solids Contamination or degradation TAN, RBOT, Routine and

spectro-metals post repair
Visual for color & clarity Cloudiness or Presence of water or TAN Routine
darkening particulates. Oxidation of
lubricant.
Spectrometals (IR spectral Metals Presence of contaminants, wear Particle count Routine
analysis) products and additives
Particle count Particles >10 Metal & wear product particles Spectro-metals Routine
µm
Ferro- Direct Ferrous Wear rate Particle count, Case basis

graphy particles up to spectro-metals
250 µm
Analytical Ferrous Microscopic examination. Particle count, Case basis

particles Diagnostic tool. spectro-metals
Micropatch Particles, Microscopic examination. Particle count, Periodic or case

debris Diagnostic tool spectro-metals, basis
ferrography
Water Content Water Degradation, leak, oxidation, Visual, RBOT Routine

emulsion
Viscosity Lubricating Contamination, degradation Water Routine

quality
Table 7–8. Lubricant Tests
d. Hydraulic Fluids—All bulk and equipment-installed hydraulic fluids supplied under this
contract shall meet the cleanliness guidelines in Table 7–9. The procuring organization
will specify System Sensitivity. In Table 7–9, the numbers in the 5 micron and 15
micron columns are the number of particles greater than 5 microns and 15 microns in a
100-milliliter sample.
The particle counting technique utilized shall be quantitative. Patch test results are not
acceptable.
The ISO numbers in the right-hand column of Table 7–9 are based on the concentration
of particles greater than 5 microns and greater than 15 microns per 100-milliliter sample.
7-126 February 2000

The concentration can then be converted to the ISO number using an ISO Range Number
Table that should be available from a hydraulic fluid vendor or lubrication laboratory.
Type of System System Suggested Maximum Particle Level

Sensitivity (Particles per 100 milliliters)
5 microns 15 ISO
microns
Silt sensitive control Super critical 4,000 250 13/9

system with very high
Reliability.
Laboratory or
Aerospace
High performance Critical 16,000 1,000 15/11
servo and high
pressure long life
systems.
Machine tools
High quality reliable Very Important 32,000 4,000 16/13
systems. General
machine requirements
General machinery Important 130,000 8,000 18/14
and mobile systems.
Med. pressure &
capacity
Low pressure heavy Average 250,000 16,000 19/15
industrial systems.
Long life not critical.
Low pressure systems Main protection 1,000,000 64,000 21/17
with large clearances
Table 7–9. Sperry Vickers Table of Suggested Acceptable Contamination

Levels for Various Hydraulic Systems
e. Insulating Fluids—The contractor shall identify the type of oil used as an insulating
fluid for all oil-filled transformers supplied under the contract. In addition, the contractor
shall test the insulating oil using the American Society for Testing Materials (ASTM) test
listed in Table 7–10 and provide the results to the Government. Any deviation from the
typical properties listed below shall be corrected by the contractor before the Government
will accept the transformer.
February 2000 7-127

Test (Units) Silicone Mineral Asakrel
Dielectric Breakdown 30+ 30+ 30+

ASTM D877 (KV)
Power Factor 0.01 0.05 max 0.05
ASTM D924 (%)
Neutralization Number <0.03 <0.03 <0.03
ASTM D974 (mg
KOH/g)
Interfacial Tension N/A 35 min N/A
ASTM D2285
(dynes/cm)
Specific Gravity 0.96 0.88 1.55
ASTM 1298
Flash Point ASTM D92 >305 160 N/A
©
Fire Point ASTM D92 © 360 177 None to Boiling
Pour Point ASTM D97 © -55 -51 max -30 max
Water Content 30 max 30 max 30 max
ASTM D1533 (ppm)
Viscosity at 40C 232 57.9 55.8-61.0
ASTM D445 (SUS)
Color & Appearance clear/water like pale yellow clear pale yellow clear
Table 7–10. Typical Properties of Transformer Oils
f. Sampling Points—The contractor shall install sampling points and lines in accordance
with Method No.1 as recommended by the National Fluid Power Association (NFPA).
Method No. 1 is published as NFPA T2.9.1-1972 titled Method for Extracting Fluid
Samples from the Lines of an Operating Hydraulic Fluid Power System for Particulate
Particle Contamination Analysis as follows:
1. For Pressurized Systems—A ball valve is placed in the fully opened position with a
downstream capillary tube (ID> 1.25 mm) of sufficient length to reduce downstream
pressure and control flow in the desired range. The sampling point shall be located in
a turbulent flow region and upstream of any filters.
7-128 February 2000

2. For Reservoirs and Non-Pressurized Systems—A 1/8" stainless steel line and ball
valve is placed in the side of the oil sump or tank. The line shall be located as close
to the midpoint of the structure as feasible. In addition, the sample line shall extend
internally to and as close to the center of the tank as possible.
7.1.10 Thermography
a. Electrical—The contractor shall perform a thermographic survey on all electrical
distribution equipment, motor control centers, and transformers during the start-up phase
of the installation unless the thermographic survey is waived by the procuring
organization.
Any defects noted by an observable difference in temperature of surveyed components or

unexplained temperature rise above ambient shall be corrected by the contractor at no
additional expense to the procuring organization. The contractor shall resurvey repaired
areas to assure proper corrective action has been taken.
b. Piping Insulation—The contractor shall perform a thermographic survey on all insulated

piping during the start-up phase of the installation unless the thermographic survey is
waived by the procuring organization.
Any voids in the piping insulation shall be corrected by the contractor at no additional
cost to the procuring organization. The contractor shall resurvey repaired areas to assure
proper corrective action has been taken.
c. Building Envelope—The contractor shall perform a thermographic survey of the

building envelope as part of the pre-beneficial occupancy to check for voids in insulation
and/or the presence of wetted insulation. In addition, the presence of air gaps in building
joints such as seams, door frames, window frames, etc., shall be checked via
thermographic survey using an appropriate procedure and specifications described in the
following:
ASTM C1060-90 Thermographic Inspection of Insulation in Envelope Cavities In

Wood Frame Buildings.
ASTM C1153-90 Standard Practice for the Location of Wet Insulation in Roofing
Systems Using Infrared Imaging.
ISO 6781 Thermal Insulation-Qualitative Detection of Thermal

Irregularities in Building Envelopes-Infrared Method.
ASTM E1186-87 Standard Practices for Air Leakage Site Detection in Buildings.
The contractor shall clearly identify by photographs, scale drawings, and/or by

description all voids or gaps noted during the thermographic scan.
February 2000 7-129

For areas where the moisture content of the insulation or building envelope is
questionable, the contractor shall use either destructive or non-destructive testing
techniques that confirm the amount of moisture. Specific testing procedures to be used
shall be proposed by the contractor and approved by the procuring organization.
d. Boilers, Furnaces, and Ovens—The contractor shall perform a thermographic survey

during the start-up phase of installation of all furnaces, boilers, and ovens as a means of
determining voids in insulation or refractory materials. Any voids detected during the
survey shall be corrected by the contractor at no expense to the procuring organization.
The contractor shall perform a thermographic survey of all repaired areas prior to final
acceptance by the procuring organization.
e. Temperature Criteria—Thermography inspections are identified as either qualitative or

quantitative. The quantitative inspection is interested in the accurate measurement of the
temperature of the item of interest. Quantitative inspections are rarely needed in facilities
applications. The qualitative inspection is interested in relative differences, hot and cold
spots, and deviations from normal or expected temperature ranges.
f. Relative Readings—In general, to locate abnormalities, compare similar components

with similar loads are compared. Taking relative readings on the same equipment and
trending over time is also effective in detecting problems.
g. Motors and Bearings— Large machines should be scanned closely. Abnormal hot spots
on the body may indicate flaws in the stator windings. The surface temperature of a
motor is normally 7.5% lower than the winding temperature. Bearing temperatures are
normally 5–20 degrees F higher than the housing temperature.
h. Power Transformers—Abnormal heat at connections may indicate looseness, corrosion,

or other flaws. Other localized heating may be indicative of flaws in windings or of
insufficient ventilation of the surrounding area. Temperature variations in cooling fins or
tubes may indicate internal cooling problems, such as a loss of coolant or plugging. A
bank of same-type transformers with significantly different temperature readings may
indicate unbalanced loading or a defective transformer.
7.1.11 Airborne Ultrasonics

The contractor shall perform an airborne ultrasonic survey during the start-up phase of the
installation unless the airborne ultrasonic survey is waived by the procuring organization. The
contractor shall survey electrical equipment for indications of arcing or electrical discharge,
including corona. Piping systems shall be surveyed for indications of leakage.
Any defects or exceptions noted by the use of airborne ultrasonics shall be corrected by the
contractor at no additional expense to the procuring organization. The contractor shall re-survey
repaired areas to assure proper corrective action has been taken.
7-130 February 2000

7.1.12 Pulse Echo Ultrasonics

The contractor shall perform material thickness measurements on a representative sample of all
material where a thickness is specified in the contract. Thickness measurements shall be
performed at the fabricator’s place of business prior to shipment of any material to the project
site. Material which does not meet the specified requirements of the contract shall not be
shipped without the prior approval of the procuring organization.
7.1.13 Motor Circuit Analysis (Complex Phase Impedance)

Upon motor installation, the contractor shall take and provide to the procuring organization the
following acceptance/baseline readings and measurements, first for the motor alone, and then,
for motor and circuit together:
• Conductor path resistance

• Inductive imbalance
• Capacitance to ground
7.1.14 Motor Current Spectrum Analysis

With the motor installed and operational, the contractor shall conduct an acceptance/baseline
spectral analysis on the loaded motor at 75% or greater load when specified by the procuring
organization.
7.1.15 Insulation Resistance

Upon installation, the contractor shall take and provide to the procuring organization the
following acceptance/baseline readings and measurements; first, for the circuit or for the motor
alone, and then, for motor and circuit together:
• Polarization Index (Motors of 500 HP or more only)

• Dielectric Absorption Ratio (for all motors)
• Leakage current at test voltage
7.1.16 Surge Testing

The contractor shall perform surge testing and high potential (high-pot) resistance testing of the
motor(s) prior to their installation and procuring organization acceptance. The contractor shall
provide to the procuring organization documentation of test results, including test voltage,
waveforms, and high potential leakage current.
February 2000 7-131

7.1.17 Start-up Tests

With the motor installed and operational, the contractor shall collect and provide to the procuring
organization the following baseline data:
• Coast-down time
• Peak starting current
7.1.18 Maintainability and Ease of Monitoring

The contractor shall provide for facility and equipment maintainability and ease of monitoring
through design. The contractor shall provide documentation to illustrate and support the
maintainability and ease of monitoring incorporated by the design.
For example, mobile industrial equipment shall be equipped with fluid sampling ports on the
engine and hydraulic systems. Accessibility to these ports shall facilitate periodic fluid sampling
and system monitoring.
7.1.19 Leveling of Equipment Upon Installation

The contractor shall level all installed rotating electrical and mechanical machinery. After
installation, the equipment shall not exceed a maximum slope of the base and the frame of 0.001
inch per foot. The contractor shall report to the procuring organization the type and accuracy of
the instrument used for measuring the level; e.g., a 12-inch machinist’s level graduated to 0.0002
inch per foot.
7.2 Architectural/Engineering (A&E) Contracts

Table 7–11 identifies the clauses that are appropriate for use in A&E contracts.
Contract Element PT&I Technology

Clause
7.1.18 Facility Maintainability and

ease of monitoring
7.1.18 Equipment Maintainability and
ease of monitoring
Table 7–11. RCM Clauses for A&E Contracts
7-132 February 2000

7.3 Construction Contracts

Table 7–12 identifies the clauses that are appropriate for use in construction contracts.
Contract Clause Equipment Type PT&I Technology

7.1.1 Measurements/surveys N/A
7.1.2; 7.1.4; 7.1.7; Pump Vibration
7.1.8
7.1.9 Pump Lubricant & wear particle
analysis
7.1.2; 7.1.5; 7.1.7; Compressor Vibration
7.1.8
7.1.9 Compressor Lubricant & wear particle
analysis
7.1.2; 7.1.6; 7.1.7; Blower/fan Vibration
7.1.8
7.1.9 Blower/fan Lubricant & wear particle
analysis
7.1.2; 7.1.3; 7.1.7; Gearbox Vibration
7.1.8
7.1.9 Gearbox Lubricant & wear particle
analysis
7.1.10 Boiler, furnace Infrared thermography
7.1.11 Piping Passive ultrasound
7.1.12 Piping/pressure vessel Pulse echo ultrasound
7.1.10 Piping insulation Infrared thermography
7.1.10 Chiller/refrigeration Infrared thermography
7.1.9 Chiller/refrigeration Lubricant & wear particle
analysis
7.1.2; 7.1.7; 7.1.8 Chiller/refrigeration Vibration
7.1.11 Electrical switchgear/ circuit Passive ultrasound
breakers
7.1.10 Electrical switchgear/ circuit Infrared thermography
breakers
7.1.15 Electrical switchgear/ circuit Insulation resistance
breakers
7.1.15 Motor & Motor Circuit Insulation resistance
7.1.13 Motor & Motor Circuit Motor circuit analysis
7.1.14 Motor & Motor Circuit Motor current spectrum
analysis
7.1.17 Motor & Motor Circuit Start up tests
February 2000 7-133

7.1.10 Building envelope Infrared thermography

7.1.10 Heat exchanger/condenser Infrared thermography
7.1.11 Heat exchanger/condenser Passive ultrasound
7.1.2; 7.1.7; 7.1.8 Electric motor Vibration
7.1.16 Electric motor Surge testing
7.1.2; 7.1.7; 7.1.8 Electrical generator Vibration
7.1.13 Electrical generator Motor circuit analysis
7.1.15 Electrical generator Insulation resistance
7.1.10 Transformer Infrared thermography
7.1.9 Transformer Oil analysis
7.1.19 Rotating Equipment Electrical Equipment leveling upon
Mechanical installation
Table 7–12. RCM Clauses for Construction Contracts
7.4 Equipment Procurement Contracts

Table 7–13 identifies the clauses that are appropriate for use in equipment procurement
contracts.
ContractClause Equipment Type PT&I Technology

7.1.2; 7.1.4; 7.1.7; Pump Vibration
7.1.8
analysis
7.1.2;7.1.5; 7.1.7; 7.1.8 Compressor Vibration
analysis
7.1.8
analysis
7.1.2; 7.1.3; 7.1.7; Gearbox Vibration
7.1.8
analysis
7-134 February 2000


analysis
7.1.11 Electrical switchgear/ circuit Passive ultrasound
breakers
7.1.10 Electrical switchgear/ circuit Infrared thermography
breakers
7.1.15 Electrical switchgear/ circuit Insulation resistance
breakers
7.1.15 Motor & motor circuit Insulation resistance
7.1.13 Motor & motor circuit Motor circuit analysis
7.1.14 Motor & motor circuit Motor current spectrum
analysis
7.1.17 Motor & motor circuit Start-up tests
7.1.2; 7.1.7; 7.1.8 Electric motor Vibration
7.1.16 Electric motor Surge testing
Table 7–13. RCM Clauses for Equipment Procurement Contracts
7.5 Maintenance and Operations (M&O) Contracts

Table 7–14 identifies clauses that are appropriate for use in M&O contracts involving RCM
features.
ContractClause Equipment Type PT&I Technology

7.1.2; 7.1.4; 7.1.7; Pump Vibration
7.1.8
analysis
7.1.2; 7.1.5; 7.1.7; Compressor Vibration
7.1.8
analysis
February 2000 7-135

7.1.8
analysis
7.1.2; 7.1.3; 7.1.8 Gearbox Vibration
analysis
analysis
7.1.11 Electrical switchgear /circuit breakers Passive ultrasound
7.1.10 Electrical switchgear /circuit breakers Infrared thermography
7.1.15 Electrical switchgear /circuit breakers Insulation resistance
7.1.15 Motor & motor circuit Insulation resistance
7.1.13 Motor & motor circuit Motor circuit analysis
7.1.14 Motor & motor circuit Motor current spectrum analysis
7.1.17 Motor & motor circuit Start-up tests
7.1.10 Building envelope Infrared thermography
7.1.2; 7.1.7; 7.1.8 Electric motor (new and rewound) Vibration
7.1.16 Electric motor (new and rewound) Surge testing
7.1.19 Rotating Equipment- Electrical & Mechanical Equipment leveling upon
installation
Table 7–14. RCM Clauses for M&O Contracts
7-136 February 2000

Chapter 8—PT&I Criteria
8.1 Baselines
Baseline data is that condition monitoring data representative of an equipment in a new and/or
properly operating condition. The baseline data is the foundation of the predictive trending
analysis required to forecast equipment condition. It is important that this baseline data is
established as early as possible in the life of the equipment. The baseline readings and periodic
monitoring data should be taken under the same conditions (or as close as can be achieved).
These conditions should be recorded. It is only under identical conditions that the relative
comparison of data is valid. Significant changes in conditions often affect the data in
unquantifiable ways because of unknown or complex relationships. Baseline readings should be
re-established each time equipment undergoes major maintenance.
8.2 Criteria by PT&I Technology
8.2.1 Vibration Monitoring

The development of specific vibration criteria for every machine at all possible operating speeds
in all applications and in every mounting arrangement is not possible. Vibration amplitude
varies with operating speed, load, and mounting arrangement, so developing criteria based solely
on amplitude can be misleading. The frequency content of the spectrum is often as important as
the amplitude. For example, the presence of a tone associated with an inner race defect on a new
bearing is unacceptable regardless of the amplitude. Furthermore, one must consider the
difference between the vibration amplitude and frequency content of a reciprocating machine as
compared to a centrifugal machine.
The vibration specifications provided in this guide are based on International Standards
Organization (ISO), American Petroleum Institute (API), American Gear Manufacturers
Association (AGMA), American National Standards Institute (ANSI), MIL-STD-167-1, MIL-
STD 740-2 (Appendix C), General Motors Vibration Specifications, and field data acquired on a
variety of machinery.
a. Developing Vibration Criteria—Specific vibration criteria are provided in this guide

where possible. Where specific criteria are not provided, the procedure provided in
paragraph 7.1.7.1.c.(4).(a) is recommended to the guide user for use in developing the
vibration criteria.
b. Vibration Analysis of New Equipment—For all large or critical pieces of equipment

assembled and run at the factory prior to shipment, a narrowband vibration spectrum
should be acquired at the locations listed in Section 7.1.8 of this guide while the
equipment is undergoing this factory performance testing. A baseline or reference
spectrum should be retained for comparison with the post-installation vibration check.
February 2000 8-137

Equipment failing the vibration criteria should be rejected by the Government prior to
shipment.
Vibration tests are recommended under the situations listed in paragraph 7.1.7.1.c.(4)(b)
if the equipment fails the initial test and/or if problems are encountered following
installation.
c. Vibration Criteria for Electric Motors
1. General—All motor vibration spectra should be analyzed at the following forcing

frequencies described in paragraph 7.1.7.1.c.(4)(c).
2. Balance - The vibration criteria listed in Table 7–1 are for the vibration amplitude at
the fundamental rotational frequency or one times running speed (1X). This is a
narrowband limit. An overall reading is not acceptable.
3. Additional Vibration Criteria—All testing should be conducted at normal operating

speed under full load conditions. Suggested motor vibration criteria are provided in
Table 7–2. In addition, Appendix E contains criteria for common machines and an
example of how to calculate criteria.
d. Rewound Electric Motors—Due to the potential of both rotor and/or stator damage
incurred during the motor rewinding process (usually resulting from the bake-out of the
old insulation and subsequent distortion of the pole pieces) a rewound electrical motor
should be checked both electrically and mechanically. The mechanical check consists of
post-overhaul vibration measurements at the same location as for new motors. The
vibration level at each measurement point should not exceed the reference spectrum for
that motor by more than 10%. In addition, vibration amplitudes associated with electrical
faults such as slip, rotor bar, and stator slot should be noted for any deviation from the
reference spectrum.
Note: Rewinding a motor will not correct problems associated with thermal
distortion of the iron.
e. General Equipment Vibration Standards
1. If rolling element bearings are utilized in either the driver or driven component of a
unit of equipment (e.g., a pump/motor combination), no discrete bearing frequencies
should be detectable. If a discrete bearing frequency is detected, the equipment
should be deemed unacceptable.
2. For belt-driven equipment, belt rotational frequency and harmonics should be

undetectable. If belt rotation and/or harmonics are detectable, the equipment should
be deemed unacceptable.
8-138 February 2000

3. If no specific criteria are available, the ISO 3945 acceptance Class A guidelines
(Appendix C) should be combined with the motor criteria contained in Table 7–2 and
used as the acceptance specification for procurement and overhaul.
f. Specific Equipment—Use the criteria shown in Table 7–3 on boiler feedwater, split
case, and progressive cavity pumps.
g. Belt Driven Fans—Use the criteria in Table 7–4 for belt-driven fans:
h. Vibration Guidelines (ISO)—Table 7–5 is based on International Standards ISO 3945

(Appendix C) and should be used as a guideline (not as an absolute limit) for determining
the acceptability of a machine for service. The vibration acceptance classes and ISO
3945 machine classes are shown in Tables 7–6 and 7–7, respectively. Note that the ISO
amplitude values are overall measurements in inches/second RMS while the
recommended specifications for electric motors are narrowband measurements in
inches/second Peak.
8.2.2 Lubricant and Wear Particle Analysis

Lubricant analysis monitors the actual condition of the oil. Parameters measured include
viscosity, moisture content, flash point, pH (acidity or alkalinity), and the presence of
contaminants such as fuel, solids, and water. In addition, the levels of additives in lubricants can
be determined. Tracking the acid/alkaline nature of the lubricant permits the identification of an
undesirable degree of oxidation, gauging the ability of the lubricant to neutralize contaminants,
and aids in the verification of the use of the correct lubricant after a lubricant change. Viscosity
(resistance to flow) provides a key to the lubricating qualities of the lubricant. These qualities
may be adversely affected by contamination with water, fuel, or solvents and by thermal
breakdown or oxidation. The presence of water reduces the ability of the lubricant to effectively
lubricate, promotes oxidation of additives, and encourages rust and corrosion of metal parts. In
performing a spectrometric analysis, one burns a small amount of the fluid sample and analyzes
the resulting light frequencies and intensities to determine the type and amount of compounds
present based on their absorption of characteristic light frequencies. Sample results are
compared to the characteristics of the same new lubricant to measure changes reflecting the
lubricant’s reduced ability to protect the machine from the effects of friction. The continued
presence of desirable lubricant additives is another key indicator of lubricant quality. Infrared
spectrometry is also capable of detecting and measuring the presence of organic compounds such
as fuel or soot in the lubricant sample.
In wear particle analysis, analysts examine the amount, makeup, shape, size, and other
characteristics of wear particles and solid contaminants in the lubricants as indicators of internal
machine condition. With experience and historical information, one can project degradation
rates and estimate the time until machine failure. Wear particle analysis includes ferrography,
which is a technique used to analyze metal wear products and other particulates. Elemental
spectrographic analysis is used to identify the composition of small wear particles and provide
information regarding wear sources. Analyzing and trending the amount, size, and type of wear
particles in a machine’s lubrication system can pinpoint how much and where degradation is
February 2000 8-139

occurring. Figure 8–1 illustrates the relationship between wear particle size, concentration and
equipment condition.
µ m)
Wear Particle Size (µ
Figure 8 – 1. Wear Particle Size and Equipment Condition
8.2.3 Thermography
There are two basic criteria for evaluating temperature conditions. They are differential
temperature (∆T) and absolute temperature. Each is described below.
a. Differential Temperature (∆ ∆ T) - Temperature difference criteria are simple, easy to

apply in the field, and provide an adequate qualitative screening system to identify
thermal exceptions and problems. The ∆T criteria compares component temperature to
the ambient temperature and may be used for electrical equipment. ∆T may also be used
for mechanical components.
The typical ∆T criteria, which may be modified easily based on experience, are as shown
in Table 8–1:
8-140 February 2000

Temperature Rise Action
10-25F Repair at Convenience
25-40F Repair Next Scheduled Availability
40-80F Repair at First Availability

Repair Immediately
> 80F
Table 8–1. Actions Required Based on Temperature Rise Under Load
b. Absolute Temperature—Absolute temperature criteria are generally specific to an

equipment model, type of equipment, class of insulation, service use, or any of many
other salient characteristics. As a result, absolute temperatures are more suited to
quantitative infrared thermography and critical temperature applications. The mechanical
temperature specifications come primarily from manufacturer’s manuals. Electrical
temperature specifications are set by three principal electrical standards organizations:
• National Electrical Manufacturers Association, (NEMA) (Appendix C).

• International Electrical and Electronic Engineers, (IEEE) (Appendix C).
• American National Standards Institute, (ANSI) (Appendix C).
A very useful summary of temperature criteria is found in the Guideline for Infrared
Inspection of Electrical and Mechanical Systems, published by the Infraspection Institute
of Shelburne, Vermont (Appendix C).
Table 8–2 provides absolute temperature limits for materials commonly found in the
Government Plants:
8.2.4 Airborne Ultrasonics

The use of a passive ultrasonic instrument as a leak detector, i.e., listening for the ultrasonic
noise characteristic of a pressure/vacuum leak, is qualitative. There are no numerical thresholds.
Many common passive ultrasonic devices operate on a relative, rather than a calibrated, absolute
scale. However, by using relative changes in intensity from baseline readings, the degradation
process may be trended and tracked.
February 2000 8-141

Component Temperature (°C)

Bearings, Roller Element Type
Races/Rolling Elements 125
Retainers (plastic) 120
Cages/Retainers/Shields (metal) 300
Bearings, Plain Type

Tin/Lead Based Babbitt 149
Cadmium/Tin-Bronze 260
Seals (lip type):

Nitrile Rubber 100
Acrylic Lip 130
Silicone/Fluoric 180
PTFE 220
Felt 100
Aluminum (lab) 300
Mechanical Seal Materials

Glass Filled Teflon 177
Tungsten Carbide 232
Stainless Steel 316
Carbon 275
V-Belts 60
Table 8–2. Temperature Limits for Selected Components
8.2.5 Motor Circuit Analysis

Motor circuit analysis measures natural electrical motor circuit characteristics, such as:
• Individual phase resistance from bus disconnect through the motor windings
(milli-ohms)
8-142 February 2000

• Inductance of the motor coils (millihenries)

• Capacitance of each phase to ground (picofarads)
During the same test series, one can measure resistance to ground of each phase (megohms)
through the use of low voltages (both AC & DC) and low currents, which are not harmful to the
motor or motor circuits.
The following procedure is recommended for use when performing motor current analysis
(MCA):
• De-energize the circuit (comply with safety instructions)

• Eliminate stray currents/voltages
• Do not disconnect/exclude components except:
− Power factor correction capacitors
− Solid state controllers
• Place as much of the circuit under test as possible, including
− Disconnects
− Motor controller contactors
− Circuit breaker(s)
A motor circuit analysis test set can provide indications of circuit problems directly in electrical
terms that can be used by maintenance personnel to pinpoint and correct faults. The test set may
then be used to perform post-repair tests.
The following are MCA resistance imbalance guidelines:
Conductor Path Resistance Imbalance Guidelines

Less than 2%—Expected and acceptable when new
Greater than 5%—Plan troubleshooting to locate cause of increased resistance when
convenient
R high - R avg
% Imbalance = X 100
R avg
February 2000 8-143

( R1 + R 2 + ... Rn )
Where : R avg =
n
Greater than 10%—Schedule effort to locate and eliminate problem in order to preserve
motor life
Inductive Imbalance Guidelines
Less than 10%—Acceptable from OEM or rewind shop
10-15%—Acceptable in service
Greater than 15%—Isolate cause(s), increase monitoring frequency
Greater than 25%—Begin planning for motor repair or replacement
Greater than 40%—Be prepared for failure, within weeks
X high - XR avg
% Imbalance = X 100
X avg
( + + ... X n )
Where : X avg = X 1 X 2
n
The following are MCA capacitance imbalance guidelines:
Capacitance Imbalance Guidelines
Capacitance imbalance is reflective of moisture and dirt in the vicinity of motor circuit
components.
Analysis is performed by trending and by making relative comparisons as follows:
• Take initial reading
• Compare readings for similar motor circuits
• Compare follow-on readings, watch for upward trends
• Identify significant differences and schedule inspection to resolve differences
8-144 February 2000

8.2.6 Motor Current Signature Analysis (MCSA)

Mechanical/electrical interactions associated with magnetic forces in and around the rotating
element of a motor are “reflected” in and around AC power supply cables. They are readily
identifiable and display repetitious flux field characteristics centered at the electrical power line
frequency (FL) of 60 Hz (3600 CPM). Through analysis and interpretation of the relationship
between the AC power line frequency and its motor generated sidebands, motor current signature
analysis may be used to detect:
• Broken rotor bars or high resistance joints (braze, crack)
• Defective rotor shorting rings (alignment, porosity, integrity)
• Rotor and stator (air gap) eccentricity (dynamic and static)
• Unbalanced magnetic pull
As the difference between the amplitude of the power line frequency and the pole pass sideband
frequencies decrease in magnitude, the greater the concern should be for the condition of the
rotor. Results indicate:
• A slight decrease may trigger increased monitoring
• A moderate decrease may indicate increasing resistance between the rotor bars
and the end ring or that a crack is developing in either
• Further decreasing values indicate rotor bar breaks
8.2.7 Insulation Resistance

There are several forms of insulation resistance measurement:
a. Megohmmeter Testing—Used to measure phase-to-phase and phase-to-ground

resistance. It gives an overall indication of insulation condition, however, reliable
trending requires temperature correction. Even the best insulation will show
unacceptably low insulation resistance readings just following an oven bake or dry-out.
b. Dielectric Absorption Ratio and Polarization Index—Insulation resistance ratios are

frequently used to evaluate insulation-to-ground conditions in order to avoid having to
compensate for temperature. A single DC voltage, usually slightly higher than the motor
rated voltage, is impressed continuously on a winding. The current induced by the DC
voltage has three components:
• Capacitive charging of the circuit, which fades quickly.
• Leakage current to ground, a constant value.
February 2000 8-145

• Current, which polarizes the molecules of the insulation surrounding the motor
circuit conductor path and fades slowly from its initial value.
The ratio of readings taken at two different times indicates the condition of the insulation,
as follows:
Megohm Reading at 1 Minute

= Dielectric Absorption Ratio
Megohm Reading at 30 Seconds
greater than1.5—OK
less than 1.25—Danger
Megohm Reading at 10 Minutes

= Polarizati on Index
Megohm Reading at 1 Minute
greater than 2 up to ~4—OK

less than 2 insulation—weak
greater than 5 insulation—possibly too dry and brittle
c. Leakage current—An overall indicator of insulation condition and cleanliness of the

equipment. The accumulation of dirt and moisture provides a path for leakage current.
There are no absolute values by which to gauge the deterioration of insulation using
leakage current. The comparison of successive values permits the comparison and
trending of leakage current.
8.2.8 Surge Testing

A surge test uses high voltage, high energy discharge pulses that are inserted into two windings
of a polyphase motor simultaneously. These pulses cycle between motor windings and the test
set. Current waveform analysis may indicate problems to an experienced and trained analyst.
The test also indicates the voltage level at which the insulation breaks down.
Surge Testing, in the view of the Electric Power Research Institute, accomplishes the following:
• The surge test could be destructive, inducing failure in weakened turn to turn
insulation. For this reason, test impulse voltage levels and rise times should be
carefully selected.
• This is a go/no-go proof test and, as such, does not provide information that will
allow making an assessment of remaining life.
• Experience is required to perform the test and to interpret the results, especially if
complete windings rather than individual coils are tested.
8-146 February 2000

8.2.9 Start-Up Tests

There are two types of start-up tests as described below:
a. Coast-down time—A simple and often overlooked test. In this test the time for the
motor to coast to a stop after the removal of power is recorded and trended. This data
tracks the mechanical condition of the motor bearings over the life of the machine.
b. Peak starting current—Another simple test which involves periodically recording the
peak starting current of a motor. This test also provides an indication of the mechanical
condition of the motor.
February 2000 8-147

8-148 February 2000

Chapter 9 - Checklists for RCM Quality Assurance
9.1 Planning
Table 9–1 contains some factors to be considered in the planning phases of facilities acquisition.
Planning QA Checklist 3
Are the RCM requirements for the facility determined?
Is built-in monitoring planned where cost-effective?
Has the use of performance data for condition monitoring been considered
and planned?
Is the collection of cost, cost avoidance, and cost savings incorporated?
Does the CMMS require a PT&I module?
Is there a mechanism provided for maintenance feedback?
Have PT&I technologies that are appropriate for the equipment been
selected?
Table 9–1. RCM Quality Assurance Planning Considerations
February 2000 9-149

9.2 Design
Table 9–2 contains some factors to be considered for quality assurance during the design phase
of facilities acquisition.
Design QA Checklist 3
Are maintainability factors considered?
Access
Material
Standardization
Quantitative goals set
Are ease of monitoring factors considered?
Access
On-line data collection
Performance indicators
Are predictive technologies specified and incorporated?
Do the contractor qualifications match the RCM requirements?
Has a predictive analysis capability been provided?
Has the distribution of raw data to those who could use it been incorporated?
Are test and maintenance results distributed to users?
Have design modifications based on maintenance feedback been incorporated?
Table 9–2. RCM Quality Assurance Design Considerations
9-150 February 2000

9.3 Construction
Table 9–3 lists some factors to consider during the construction phase of facilities acquisition.
Construction QA Checklist 3
Were acceptance testing requirements established (prior to construction mobilization)?
Do the contractor’s qualifications indicate an adequate understanding of RCM?

Is the contractor conforming to specifications and drawings?
Is the contractor conforming to bills of material?
Is the contractor conforming to installation procedures?
Has the training of maintenance personnel been initiated?
Is the selection of maintenance tasks in progress?

Has the writing of maintenance procedures and instructions been initiated?
Are baseline condition and performance data recorded and made available for equipment as it is
installed?
Does the contractor need specialized subcontractors?
Have the contractor equipment submittals been approved?
Table 9–3. RCM Quality Assurance Construction Considerations
9.4 Equipment Procurement

Table 9–4 lists some factors to consider during the equipment procurement phase of facilities
acquisition.
Equipment Procurement QA Checklist 3
Are specifications determined to meet RCM requirements?

Are acceptance testing requirements specified in the procurement documents?
Are contractor qualifications matched to RCM requirements?
Is a feedback system in place for continuous equipment improvement?
Has a provision been made for equipment condition monitoring, if applicable?
Are baseline data required?
Are equipment life cycle costs required/provided?
Are embedded (on-line) sensors required/provided?
Table 9–4. RCM Quality Assurance Equipment Procurement Considerations
February 2000 9-151

9.5 Maintenance and Operations

Table 9–5 contains some factors to be considered during the maintenance and operations phase
of a facility life cycle.
Maintenance and Operations QA Checklist 3
Is the inventory of skills to support the RCM program available?

Is training planned to fill skill and technical shortcomings?
Does the training support the development of predictive analytical skills?
Does the training support RCM management and supervisory skills?
Are the documentation, procedures and work practices capable of supporting
RCM?
Are the responsibilities for systems and equipment defined and assigned?
Are the maintenance history data and results distributed to proper users?
Is there a feedback system in place for continuous maintenance program
improvement?
Is root-cause failure analysis in use and effective?
Are failed components subject to post-failure examination and results recorded?
Are predictive forecasts tracked and methods modified based on experience?
Are PM task and CM monitoring periodicities adjusted based on experience?
Does the CMMS fully support the maintenance program?
Are maintenance cost, cost avoidance and cost savings data collected, analyzed
and disseminated?
Is baseline condition and performance data updated following
major repair or replacement of equipment?
Are appropriate measures of maintenance performance (metrics) in use?
Table 9–5. RCM Quality Assurance Maintenance and Operations Considerations
9-152 February 2000

Chapter 10 – Key Performance Indicators (Metrics)16
10.1 General
There are a number of management indicators used to measure the effectiveness of an RCM
program. The most useful indicators are numerical. The numerical, or quantified indicators,
often referred to as Ametrics,@ can be expressed as goals and objectives, measured and displayed
in several ways for the purpose of analysis and management decision making. This chapter
addresses the description, benefits and methods for using metrics as an integral part of the
Reliability Centered Maintenance (RCM) implementation process. These quantifiable indicators
can be expressed as goals and objectives, measured and displayed in several ways for the
purpose of analyzing the effectiveness of the RCM program and to support the decision making
process.
RCM is described as a maintenance strategy that logically incorporates the optimum mix of
reactive, preventive, predictive, and proactive maintenance practices. Since these maintenance
practices, rather than be applied independently, are integrated to take advantage of their
respective strengths in order to maximize facility and equipment operability and efficiency
while minimizing life cycle costs, Metrics must be in place to measure how well the following
are achieved:
• Maintenance integration
• Maintenance optimization
• Maximized operability and efficiency
• Life-cycle cost control
These are all areas that require a method to manage and to describe the effectiveness of
implementing RCM. Metrics are the key to measuring, managing and benchmarking all phases
of the RCM implementation process.
10.2 Purpose of Metrics

Metrics provide a yardstick to measure performance and effectiveness. There is an old saying,
"If you don’t measure it, you can't manage it". In this time when many changes to maintenance
processes and technologies are being implemented, a system is needed to help achieve goals,
measure implementation progress, and benchmark with others. Vital to the success of any
program for facilities maintenance management is a hierarchy of distinct metrics, all linked to
management goals.
16
Metrics and Benchmarks developed by Mr. Alan Pride, Mr. Robin Rubrecht and Ms. Nancy Bray and presented
presentation to the Association for Facilities Engineering’s Facilities America ’99 conference October 16-20, 1999.
February 2000 10-153

To management, Metrics are used in the strategic planning process for the development,
optimization and direction of management objectives. Metrics should reveal the effectiveness
of the management program, and measure costs (to support the budget process). Management is
responsible for the translation of technical level metrics into overall facilities maintenance
management metrics, which support NASA goals and objectives. Metrics can be used to support
the functions of staffing, budget formulation, training, contracting, and to ensure compliance
with certain regulatory requirements.
Metrics are needed to monitor and control the performance of specific equipment, systems, and
processes. Supervisors, Engineers, Technicians, and Crafts use these metrics to support
optimization and continuous improvement of the maintenance program.
10.2.1 Metrics Ownership

An important aspect of any performance measurement system is ownership. Managers and
workers at all levels of the organization need to participate in the development and refinement of
metrics in their functional areas, thereby generating a sense of ownership. Metrics must reflect
results which managers and workers can effectively change through job performance. It is this
sense of ownership that supports the continuous improvement process.
10.2.2 Definition of Metrics

Metrics are relationships used for indicating the effectiveness of an operation and for comparing
performance with goals and objectives. There are two types of performance indicators:
intangible and tangible (words and numbers). Metrics are tangible, and thus preferred, as they
are quantitative, objective, precise, and more easily trended than intangible benefits. Metrics
should consist of a descriptor and a benchmark. In addition, Metrics can be global or event
based.
10.2.2.1 Descriptor
A descriptor is a word or group of words describing the units, the function, or the process to be
measured. Examples are the number of corrective actions developed by the PT&I program, the
number of hours of equipment run-time, and the equipment availability expressed as a ratio of
equipment hours available to equipment hours required.
10.2.2.2 Benchmark
A benchmark is a numerical expression of a goal or objective to be achieved. It is that against
which one measures one=s performance. It can be an absolute number or a range. For example,
the benchmark for equipment availability might be 90%. The metric (descriptor and benchmark)
would therefore be:
Equipment available (hours)

= 90%
Equipment required (hours)
10-154 February 2000

10.3 Sample Metrics

The following are sample metrics one might choose to measure the effectiveness of an RCM
program. The benchmarks suggested are averages taken from approximately 50 major
corporations world-wide surveyed in the early 1990s:
Metric Benchmark
a. Equipment Availability 96%
Hours Each Unit of Equipment is Available to Run at Capacity

%=
Total Hours During the Reporting Time Period
b. Maintenance Overtime Percentage 5% or less
Total Maintenanc e Overtime Hours During Period

%=
Total Regular Maintenanc e Hours During Period
c. Emergency Percentage 10% or less
Total Hours Worked on Emengency Jobs

%=
Total Hours Worked
d. Percent of Candidate Equipment Covered by PT&I 100%
Number of Equipment Items in PT & I Program

%=
Total Equipment Candidates for PT & I
e. Percent of Emergency Work to PT&I and PM Work 20% or less
Total Emergency Hours

%=
Total PT & I & Preventive Maintenanc e Hours
f. Percent of Faults Found in Thermographic Survey 3% or less
Number of Faults Found

%=
Number of Devices Surveyed

Metric Benchmark
g. Percent of Faults Found in Steam Trap Survey 10% or less
Number of Defective Steam Traps Found

%=
Number of Steam Traps Surveyed
h. Ratio of PM/PT&I Work to Reactive Maintenance Work
A = 70% PM/PT&I
B = 30% Reactive Maintenance
Manhours of PM/PT & I Work

A% =
Manhours of Reactive + PM/PT & I Work
Manhours of Reactive Work

B% =
Manhours of Reactive + PM/PT & I Work
A% + B% = 100%
10.4 Trending Indicators

The following indicators also are recommended for consideration for trending as maintenance
program management tools:
$ Equipment (by classification) percentage out-of-service time for repair

maintenance.
$ Mean time between equipment overhauls and replacement.
$ Number of vibration-related problems found and corrected per month.
$ Number of vibration-related work orders open at the end of the month.
$ Number of vibration-related work orders over 3 months old.
$ Number of problems found by other PT&I techniques (i.e., infrared

thermography, ultrasonics, lube oil analysis, etc.) and corrected per month, work
orders open at the end of the month, and work orders over 3 months old.
$ A monthly record of the accumulated economic benefits or cost avoidance for the
various PT&I techniques.

$ Number of spare parts eliminated from inventory as the result of the PT&I
program.
$ Number of overdue PM work orders at the end of the month. (Total number of
PM actions should decrease.)
$ Aggregate vibration alert and alarm levels (trending down).
10.5 Recommended Agencywide Facilities Metrics

A NASA Inter-center working group lead by KSC and LaRC, with input from the other Centers,
has recommended to NASA Headquarters17, Code JX, that the following four metrics be used to
track Facilities Maintenance:
a. Requirements vs. Funding vs. ActualsC C The purpose of this metric is to

demonstrate the variance between identified needs, approved funding levels, and
actual expenditures. The funding should be broken down by Facility Classification
(i.e., Mission Critical, Mission Support, and Center Support).
The recommended terms are Annual Maintenance Requirement (AMR), Annual

Maintenance Funding (AMF), and Annual Maintenance Actual (AMA). These
include the labor and material for PM, PT&I, PGM, Repair, TC, and ROI as defined
by latest edition of NHB 8831.2 Appendix A.
b. Backlog of Maintenance and Repair (BMAR)CCThe purpose of this metric is to

track the change in BMAR by fiscal year.
This metric includes CoF as well as center-level funded projects that are identified
but not funded. BMAR does not include routine recurring work with a frequency of
less than one year.
The metric should be broken down by Facility Classification.
c. Facility ReliabilityCCThe purpose of this metric is to identify the reliability of

facilities and systems based on the level of unplanned work that must be applied to
the facility or system. The metric is the ratio of planned actual maintenance (AMA)
to total maintenance performed. Planned maintenance includes PM, PT&I, PGM, and
planned repairs and ROI. Planned maintenance does not include design engineering,
planning and estimating, scheduling, supervision, etc.
17
KSC letter IM-FEO-A from Nancy Bray dated June 7, 1996, Final Recommendation of Agency wide Facilities
Maintenance Metrics.

d. Log of Unplanned Failures and Avoided FailuresC C The purpose of this metric is to
demonstrate the impact of the overall maintenance program effectiveness by tracking
failures and failures avoided by detection of the failure precursor through either PM
or PT&I.
10.6 Metric Selection

Significant thought must go into the process of selecting Metrics to support the maintenance
program. The value of meaningful Metrics cannot be overstated, however the value of Metrics
that are inaccurate or inapplicable cannot be understated. One must first identify the goals and
objectives of the organization because they will have an impact on the selection of Metrics at all
levels of maintenance activity. Do not pick Metrics that you cannot possibly obtain, shoot for
things you can control. Issues of concern should also be identified so that they will be
considered in the selection of Metrics. All processes owners who are key to the implementation
of the overall effort should have a metric to indicate goals and progress. In each case the process
owners and implementers, as previously stated, should have a stake in selecting the Metrics to be
used. This will foster the acceptance of collecting data to support the Metrics and will also
promote the use of the Metrics for continuous improvement. One must certainly consider the
capabilities of the organization to collect the data for Metrics, i.e. the process used for collecting
and storing the data and the ease of extracting and reporting the Metrics. In doing this, we must
calculate the cost of obtaining data for Metrics and the relative value they add to the overall
program. As we are advocating doing the right things within the maintenance program with life-
cycle cost as a driver, we must also pay close attention to the cost of the capturing supporting
Metrics.
10.7 Benchmark Selection

After selection of the appropriate metrics is complete, benchmarks should be established to
characterize the organizations’ goals and/or progress points for using these metrics as a tool for
maintenance optimization and continuous improvement. Benchmarks may be derived from the
organizational goals and objectives or they may be selected from a survey performed with
similar organizations. These benchmarks will be used as a target for growth and to evaluate risk
associated with non-achievement of progress.
10.8 Utilization of Metrics

After benchmarks are established and data is being collected, we must act on the information in a
timely manner in order to maintain continuity within all of the processes which are counting on
Metrics as a performance enhancement tool. In order to take full advantage of the benefits of
Metrics they should be displayed in public areas.
The tracking and publication of Metrics informs the people of what is important, what are the
goals, and where do they stand with respect to performance expectations. The impact of
displaying Metrics often has an immediate effect on the workers in the functional area being

measured. In addition, Metrics are an integral part of any Team Charter as they allow the Team
and Management to determine Team productivity.
10.9 Examples of Benchmarks

The following tables provide examples of Benchmarks. All data is for the upper quartile of
chemical and process industrial plants.
When using Benchmarks it is important to focus on patterns and not individual data points. For
example, if the maintenance budget as a percent of Current Replacement Value (CRV) is below
1% it could be either 1) due to an effective maintenance program or 2) an indicator that the
facility is being consumed.

MAINT. MAINT COST TRAINING MAINT. COST AS CONTRACTOR COST

COST AS % AS (%) OF COST/ MAINT. PERCENT OF AS PERCENT OF
OF HRLY. TOTAL TOTAL MAINT. COST
CONTROL-
DATA SOURCE CRV LABLE COST ($US) SALES
PRIVATE High 6.0 26.1 1,990 14.1 46

INDUSTRY Mean 3.1 18.0 1,010 7.7 21
Low 1.5 8.4 210 0.5 0

BEST
L1 L H L L or H2
High (H) or
Low (L)
Table 10 – 1. Financial Benchmarks
Notes: 1. If a maintenance budget is below 2% of Current Replacement Value (CRV) the overall condition of
the facility should be evaluated to determine if the infrastructure is under-going slow degradation or if
an excessive number of projects are required to maintain the facilities.
2. Either High or Low is acceptable depending on the strategic plans for the facility, i.e., if the decision
has been made to out source either a portion or all of the maintenance function.

REPORTING MAINT. MAINT. MAINT. MAINT. MAINT. MAINT.

LEVELS HRLY/MAINT HRLY/FIRST HRLY/ HRLY/STOR HRLY/ HRLY AS
SUPPORT LINE MAINT. E-ROOM MAINT. % OF
DATA SOURCE STAFF SUPERVISOR PLANNER EMPLOYEE ENGINEER TOTAL
PRIVATE High 6.0 6.5 28 62 25.0 77 51

INDUSTRY
Mean 4.5 4.1 15.7 41 18.5 32 24
Low 3.0 2.4 7.6 19 8.6 24 4

BEST
High (H) or L H H H H L L
Low (L)
Table 10 – 2. Organizational Benchmarks
EMERGENCY PM/PT&I WORK PLANNED PM AVERAGE

WORK WORK ORDER REPAIR SCHEDULE WORK
ORDERS ORDERS COVERAGE COMPLIANCE COMPLIANCE WEEK
(%) (%) (%) (%) (%)
DATA SOURCE (Hrs.)
PRIVATE High 22.2 27.3 100 89 100 50.5

INDUSTRY Mean 7.8 13.4 88 65 91
Low 2.1 5.4 78 50 77 41.3

BEST
L H H H H L
High (H) or
Low (L)
Table 10 – 3. Work Practices Benchmarks

BACKLOG CRV/ MAINT. NUMBER OF HOURLY OSHA Injuries HOURLY

LEVELS HOURLY CRAFT TURNOVER Per ABSENTEE
DATA SOURCE ($000,000US) ($000,000US) LINES (%) 200K Hours (%)
N/A 7.2 13.0 7.4 18 4.1

PRIVATE High
INDUSTRY Mean N/A 4.8 5.5 3.8 4 2.1
Low N/A 2.1 1.2 1.1 0 0.2

BEST
High (H) or L H1 L L L L
Low (L)
Table 10 – 3. Work Practices Data (Cont.)

10.10 Planning & Scheduling Metrics

1. BACKLOG OF READY TO WORK JOBS (Target = 3 to 5 Crew Weeks)
Total Estimated Labor Hrs. for All Ready to Work Jobs

Crew Weeks =
Actual Hours Avaliable to Schedule Each Week
2. BACKLOG OF ALL OPEN WORK ORDERS (Target = 4 to 6 Crew Weeks)
Total Estimated Labor Hrs. for All Open Work Orders

Crew Weeks =
Actual Hours Available to Schedule Each Week
3. SCHEDULE COMPLIANCE (Target = 90% or better)
Total Labor Hrs. Worked on Scheduled Jobs

%=
Total Labor Hrs. Scheduled
4. ESTIMATED MANHOURS VERSUS ACTUAL MANHOURS IN COMPLETED JOBS

(Target = ± 15%)
Total Estimated Labor Hrs. for Completed Work Orders for Week
%=
Total Actual Labor Hrs. for Completed Work Orders for Week
5. BACKLOG OF LOGBOOK JOBS (Target - Less than half the number of Logbook jobs
competed in a single week)
Number of open jobs in the Electronic Logbook at the end of the month.
6. AVERAGE LABOR HRS. SPENT ON LOGBOOK JOBS (Target = 2 Labor Hours or

less)
Total Labor Hrs. spent on Logbook Jobs

Labor Hrs./Logbook Job =
Total Logbook Jobs completed for the Week

7. INDIRECT MANHOURS PERCENTAGE (Target = 2% or less)
Total Indirect Hours

%=
Total Hours Worked
8. TOTAL UNPLANNED REPAIR WORK ORDERS OVER 30 DAYS OLD
Number of Unplanned Repair Work Orders over 30 days old at the end of the month per
Planner.
9. TOTAL NUMBER OF OPEN AND CLOSED WORK ORDERS
Total number of open Work Orders at the end of the month. (Trending down or level)
Total number of closed Work Orders during the month. (Trending up or level)
10.11 RCM Metrics

1. PERCENT OF PRODUCTION LINE AVAILABILITY (Target = 96%)
Hours each critical Facility is Available to Run at Capacity

%=
Total Hours During the Reporting Time Period
2. MAINTENANCE COST PER UNIT OF PRODUCTION (Target = Declining Annually)
Total Maintenanc e Cost per Time Period

Cost/Unit =
Total Finished Units Produced per Time Period
3. MAINTENANCE OVERTIME PERCENTAGE (Target = 5% or less)
Total Maintenanc e Overtime Hours During Period

%=
Total Regular Maintenanc e Hours During Period
4. EMERGENCY PERCENTAGE (Target = 10% or less)
Total Hours Worked on Emergency Jobs

Labor Hrs. % =
Total Hours Worked
Total Emergency Jobs Worked

Jobs % =
Total Jobs Worked
5. PERCENT OF EQUIPMENT COVERED BY CONDITION MONITORING (Target =

100%)
Number of Equipment Items in Predictive Maintenanc e Program

%=
Total Equipment Candidates for Predictive Maintenanc e
6. PERCENT OF EMERGENCY WORK TO PT&I AND PM WORK (Target <20%)
Total Emergency Hours

%=
Total Predictive & Preventive Maintenanc e Hours
7. PERCENT OF FAULTS FOUND IN THERMOGRAPHIC SURVEY (Target <3%)
Number of Faults Found

%=
Number of Devices Surveyed
8. PERCENT OF FAULTS FOUND IN STEAM TRAP SURVEY (Target = 10% or less)
Number of Defective Steam Traps Found

%=
Number of Steam Traps Surveyed
9. RATIO OF PM/PT&I WORK TO CORRECTIVE MAINTENANCE WORK
Target = 70% PM/PT&I work.

Target = 30% Corrective Maintenance work.


Appendix A—Glossary
Age Exploration The process of determining the most effective intervals for maintenance
tasks. Its called age exploration because it is often associated with identifying age related
maintenance actions such as overhaul and discard tasks and then extending the interval between
tasks.
Availability (1) Informally, the time a machine or system is available for use. (2) From the
Overall Equipment Effectiveness calculation, the actual run time of a machine or system divided
by the scheduled run time. Note that Availability differs slightly from Asset Utilization
(Uptime) in that scheduled run time varies between facilities and is changed by factors such as
scheduled maintenance actions, logistics, or administrative delays.
Benchmarking To seek out the best examples of methods, processes, procedures, and
products in order to establish a standard and assess ones own performance in terms of quality,
productivity, or cost.
B-Life The time at which a set percentage of failures are expected. For example, the B1 life is
when 1% of the units being examined will have failed; B10 is when 10% of the units will have
failed.
Building Commissioning The systematic process for achieving, verifying, and documenting
that the performance of NASA Faculties and Collateral Equipment meets the design intent. The
process extends through all phases of a project and culminates with occupancy and operation.
The process includes the testing and accepting of new or repaired building, system or component
parts to verify proper installation.
Calibration A scheduled maintenance task characterized as an Inspection. See Inspection.
Collateral Equipment Encompasses building-type equipment, built-in equipment, and large,

substantially affixed equipment/property and is normally acquired and installed as part of a
facility project as described below (also see Non-collateral Equipment):
Building-Type Equipment. A term used in connection with facility projects to connote

that equipment normally required to make a facility useful and operable. It is built in or
affixed to the facility in such a manner that removal would impair the usefulness, safety,
or environment of the facility. Such equipment includes elevators; heating, ventilating
and air conditioning systems; transformers; compressors; and other like items generally
accepted as being an inherent part of a building or structure and essential to its utility. It
also includes general building systems and subsystems such as electrical, plumbing,
pneumatic, fire protection, and control and monitoring systems.
Built-In or Large, Substantial Affixed Equipment. A term used in connection with

facility projects of any type other than building-type equipment that is to be built in,
February 2000 A-167

affixed to, or installed in real property in such a manner that the installation cost,
including special foundations or unique utilities service, or the facility restoration work
required after its removal is substantial.
Commissioning The process of testing and accepting a system, line, building and other plant
component. It is often the first (and sometimes last) opportunity for the "maintenance
department" to identify a design or build defect. Also see Building Commissioning.
Computerized Maintenance Management System (CMMS) A set of computer software

modules and equipment databases containing facility data with the capability to process the data
for facilities maintenance management functions. They provide historical data, report writing
capabilities, job analysis, and more. The data describe equipment, parts, jobs, crafts, costs, step-
by-step instructions, and other information involved in the maintenance effort. This information
may be stored, viewed, analyzed, reproduced and updated with just a few keystrokes. The
maintenance-related functions typically include –
a. Facility/Equipment Inventory
b. Facility/Equipment History
c. Work Input Control
d. Job Estimating
e. Work Scheduling and Tracking
f. Preventive and Predictive Maintenance
g. Facility Inspection and Assessment
h. Material Management
i. Utilities Management
Condition Assessment Condition assessment is the inspection and documentation of the

material condition of facilities and equipment, as measured against the applicable maintenance
standard. It provides the basis for long-range maintenance planning as well as annual work plans
and budgets.
Condition Monitoring (also know as Predictive Maintenance) The continuous or periodic

monitoring and diagnosis of systems and equipment in order to forecast failure. OR
Condition Monitoring: The continuous or periodic monitoring and diagnosis of systems and
equipment in order to forecast failure. Condition Monitoring is a Time- or Cycle-Based
Maintenance Action. Condition Monitoring is also known as Predictive Maintenance.
Condition-Based Maintenance Facility and equipment maintenance scheduled only when the
condition of the facility or equipment requires it. CBM replaces maintenance scheduled at
arbitrary time or usage intervals. It usually involves the application of advanced technology to
detect and assess the actual condition
Corrective Maintenance See Repair.
A-168 February 2000

Cost Effective An economic determination of the Maintenance Approach and entails

evaluation of maintenance costs, support costs, and consequences of failure. Also see Effective
Maintenance Task.
Current Replacement Value (CRV) Approximate cost to replace an existing facility in its
present form. NASA calculates CRV by escalating facility and collateral equipment acquisition
cost, and any incremental book value changes of $1,000 or more to present-year dollars using the
Engineering News Record (ENR) Building Cost Index (BCI). The NASA Real Property Data
System program or NASA Headquarters-approved equivalent is used in performing the required
calculations.
Critical Failure A failure involving a loss of function or secondary damage that could have a
direct adverse effect on operating safety, on mission, or have significant economic impact.
Critical Failure Mode A failure mode that has significant mission, safety or maintenance
effects that warrant the selection of maintenance tasks to prevent the critical failure mode from
occurring.
Dominant Failure Mode A single failure mode that accounts for a significant portion of the
failures of a complex item.
Effective Maintenance The application of the maintenance approach that will produce the
required availability, at the lowest cost, without compromising human safety or health, the
environment, or any other conditions the organization specifies.
Effective Maintenance Task A task that is characterized as performing its defined function
with a high degree of success for a specified cost. A maintenance task must be both applicable
and effective. The benefit of performing the task must be evaluated against the cost. Cost
includes many elements; the cost of the task, repair costs when failure occurs, collateral damage
caused by failure, and the cost of lost mission (such as production, space and flight operations,
research, and administrative support) due to the loss of the facilities and collateral equipment
function.
Facilities Maintenance The recurring day-to-day work required to preserve facilities

(buildings, structures, grounds, utility systems, and collateral equipment) in such a condition that
they may be used for their designated purpose over an intended service life. It includes the cost
of labor, materials, and parts. Maintenance minimizes or corrects wear and tear and thereby
forestalls major repairs. Facilities maintenance includes Preventative Maintenance, Predicative
Testing & Inspection, Grounds Care, Programmed Maintenance, Repair, Trouble Calls,
Replacement of Obsolete Items, and Service Request (Not a maintenance item but work
performed by maintenance organizations). Facilities Maintenance does not include new work or
work on non-collateral equipment.
Failure A cessation of proper function or performance; inability to meet a standard;

nonperformance of what is requested or expected.
February 2000 A-169

Failure Effect The consequences of failure.
Failure Mode: The manner of failure. For example, the motor stops is the failure, the reason the
motor failed was the motor bearing seized which, is the failure mode.
Failure Modes and Effects Analysis (FMEA)  Analysis used to determine what parts fail,
why they usually fail, and what effect their failure has on the systems in total. An element of
Reliability Centered Maintenance (RCM).
Failure Rate The number of failures divided by an interval such as time or cycles. The failure
rate will change over time and can be greater than one (but will never be less than zero).
Fiscal Year In the Federal Government, it is the 12-month period from Oct. 1 of one calendar
year through Sept. 30 of the following year.
Function Defined performance standard. Usually quantitative in nature (flow rate, cooling
capacity, etc.).
Inspection A time- or cycle-based action performed to identify hidden failure or potential

failure.
Infrared Thermography A predictive technique that uses infrared imaging to identify defects
in electrical and electro-mechanical devices such as fuse boxes, circuit breakers, and switchgear.
It also can be used effectively in a non-predictive manner to detect thermal cavities and leaks in
walls, ceilings, and rooftops, the correction of which can result in sizeable reductions in heating
and air conditioning expenses. Thermal imaging is extremely sensitive, and since it evaluates the
heat an object emits, emittance and reflective factors of the object and environment must be
considered.
Key Performance Indicator (KPI)  Critical few (key) indicators aligned throughout the
organization that measure controllable performance and contribute towards achieving the
organization objectives.
Life Cycle See System Life Cycle.
Maintainability The ability to retain or restore function within a specified period of time,
when provided with an identified level of tools, training, and procedures. Maintainability factors
include machine and systems access, visibility, simplicity, ease of monitoring or testing, special
training requirements, special tools, and capability of local work force
Maintenance Action taken to retain function (i.e., prevent failure). Actions include Preventive
Maintenance, Predictive Testing & Inspection, lubrication and minor repair (such as replacing
belts and filters), and inspection for failure. Also see Preventive Maintenance and Predictive
Testing & Inspection.
Maintenance Approach The plan to prevent failure and, when failure occurs, perform repair.
A-170 February 2000

Mean Time Between Failure (MTBF) The reciprocal of the failure rate; the average time to
fail. The MTBF is sometimes called the Mean Time To Fail (MTTF).
Mean Time To Fail (MTTF) See Mean Time Between Failure.
Mission Critical A building, area, or system that is critical to the Center/Facility mission or
essential for Center of Excellence performance. Also see Mission Support and Center/Facility
Support.
Mission Support A building, area, or system that provides support to the Center/Facility
primary mission or Center of Excellence assignment. Also see Mission Critical and
Center/Facility Support.
Motor Circuit Analysis (MCA)— A predictive technique whereby the static characteristics
(i.e.; impedance, capacitance to ground, inductance) of a motor or generator are measured as
indicators of equipment condition.
Motor Current Spectrum Analysis (MCSA)— A predictive technique whereby motor current
signatures provide information on the electro-mechanical condition of AC induction motors. It
detects faults such as broken rotor bars, high resistance joints, and cracked rotor end rings by
collecting motor current spectrums with clamp-on sensors and analyzing the data.
Non-collateral Equipment— All equipment other than collateral equipment. Such equipment,
when acquired and used in a facility or a test apparatus, can be severed and removed after
erection or installation without substantial loss of value or damage thereto or to the premises
where installed. Noncollateral equipment imparts to the facility or test apparatus its particular
character at the time, e.g., furniture in an office building, laboratory equipment in a laboratory,
test equipment in a test stand, machine tools in a shop facility, computer in a computer facility,
and it is not required to make the facility useful or operable as a structure or building. (See also
Collateral Equipment.)
Pareto Analysis A problem solving tool that breaks data down into manageable groups and
identifies the greatest opportunity for return on investment. The analysis is based on the Pareto
Principle, also known as the 80:20 Rule. Simply stated, the principle says that 20% of a
population will cause 80% of the problems associated with the population.
Performance Standards— Those standards which an item is required to meet in order to

maintain its required function. The performance standard defines functional failure for the item.
Potential Failure An identifiable condition that indicates a failure is imminent.
Predictive Testing & Inspection (PT&I) The use of advanced technology to assess machinery
condition. The PT&I data obtained allows for planning and scheduling preventive maintenance
or repairs in advance of failure. Also see Condition Monitoring and Condition-Based
Maintenance.
February 2000 A-171

Preventive Maintenance (1) Also called time-based maintenance or interval-based

maintenance. PM is the planned, scheduled periodic inspection, adjustment, cleaning,
lubrication, parts replacement, and minor (no larger than Trouble Call scope) repair of equipment
and systems for which a specific operator is not assigned. PM consists of many checkpoint
activities on items that, if disabled, would interfere with an essential Center operation, endanger
life or property, or involve high cost or long lead time for replacement. In a shift away from
reactive maintenance, PM schedules periodic inspection and maintenance at predefined time or
usage intervals in an attempt to reduce equipment failures. Depending on the intervals set, PM
can result in a significant increase in inspection and routine maintenance; however, a weak or
nonexistent PM program can result in safety and/or health risks to employees, much more
emergency work, and costly repairs.
(2) Time- or cycle-based actions performed to prevent failure, monitor condition, or inspect for
failure.
Predictive Maintenance See condition monitoring.
Proactive Maintenance The collection of efforts to identify, monitor and control future
failure with an emphasis on the understanding and elimination of the cause of failure. Proactive
maintenance activities include the development of design specifications to incorporated
maintenance lessons learned and to ensure future maintainability and supportability, the
development of repair specifications to eliminate underlining causes of failure, and performing
root cause failure analysis to understand why in-service systems failed.
Programmed Maintenance (PGM) Those maintenance tasks whose cycle exceeds one year,
such as painting a building every fifth year. (This category is different from PM in that if a planned
cycle is missed the original planned work still remains to be accomplished, whereas in PM only the
next planned cycle is accomplished instead of doing the work twice, such as two lubrications, two
adjustments, or two inspections.)
Reactive Maintenance See Repair.
Reliability The dependability constituent or dependability characteristic of design. From

MIL-STC-721C: Reliability - (1) The duration or probability of failure-free performance under
stated conditions. (2) The probability that an item can perform its intended function for a
specified interval under stated conditions.
Reliability-Centered Maintenance (RCM) The process that is used to determine the most
effective approach to maintenance. It involves identifying actions that, when taken, will reduce
the probability of failure and which are the most cost effective. It seeks the optimal mix of
Condition-Based Actions, other Time- or Cycle-Based actions, or Run-to-Failure approach.
Repair That facility work required to restore a facility or component thereof, including
collateral equipment, to a condition substantially equivalent to its originally intended and
designed capacity, efficiency, or capability. It includes the substantially equivalent replacements
A-172 February 2000

of utility systems and collateral equipment necessitated by incipient or actual breakdown. Also,
restoration of function, usually after failure. Also see Planned Repair.
Root Cause Failure Analysis (RCFA) The process of exploring, in increasing detail, all
possible causes related to a machine failure. Failure causes are grouped into general categories
for further analysis. For example, causes can be related to machinery, people, methods,
materials, policies, environment, and measurement error.
Run-to-Failure A Maintenance Approach where no action is taken (Time- or Cycle-Based

actions), following installation, to prevent failure. Candidate systems or machines for Run-to-
Failure are usually low-cost, easily-repaired, and non-critical.
Time- or Cycle-Based Actions Maintenance activities performed from time-to-time that have
proven to be effective in preventing failure. Items such as lubrication and restoration of wear fit
this description. Other items that are Time- or Cycle-Based are inspection and condition
monitoring. Also see Predictive Testing and Inspection.
Vibration Analysis— The dominant technique used in predictive maintenance. Uses noise or
vibration created by mechanical equipment to determine the equipment’s actual condition. Uses
transducers to translate a vibration amplitude and frequency into electronic signals. When
measurements of both amplitude and frequency are available, diagnostic methods can be used to
determine both the magnitude of a problem and its probable cause. Vibration techniques most
often used include broadband trending (looks at the overall machine condition), narrowband
trending (looks at the condition of a specific component), and signature analysis (visual
comparison of current versus normal condition). Vibration analysis most often reveals problems
in machines involving mechanical imbalance, electrical imbalance, misalignment, looseness, and
degenerative problems.
February 2000 A-173

A-174 February 2000

Appendix B—Abbreviations/Acronyms
AC Alternating Current
AE Age Exploration
AGMA American Gear Manufacturer’s Association
AMA Annual Maintenance Actual
AMF Annual Maintenance Funding
AMR Annual Maintenance Requirements
ANSI American National Standards Institute
API American Petroleum Institute
ASNT American Society for Non-Destructive Testing
ASTM American Society for Testing and Materials
AWP Annual Work Plan
BMAR Backlog of Maintenance and Repair
CAD/CAM Computer-Aided Design/Computer-Aided Manufacturing
CI Continuous Improvement
CMMS Computerized Maintenance Management System
CPM Cycles per Minute
CRV Current Replacement Value
DC Direct Current
DP Dye Penetrant
DR Direct Reading (Ferrography)
DSA Digital Signal Analysis
EPRI Electric Power Research Institute
February 2000 B-175

FCA Facility Condition Assessment
FFT Fast Fourier Transform
FMEA Failure Modes and Effects Analysis
FTIR Fourier Transform Infrared
HP Horsepower
Hz Hertz; Cycles per Second
IEEE Institute of Electrical and Electronic Engineers
IRT Infrared Thermography
ISO International Organization for Standardization
KPI Key Performance Indicator
M&O Maintenance and Operations
MCA Motor Circuit Analysis
MCSA Motor Current Signature Analysis
MDT Mean Down Time
MT Magnetic particle Testing
MTBF Mean Time Between Failure
MTBM Mean Time Between Maintenance
NDT Non-Destructive Testing
NEMA National Electrical Manufacturers Association
NFPA National Fluid Power Association
NLGI National Lubrication and Grease Institute
OEM Original Equipment Manufacturer
PdM Predictive Maintenance
B-176 February 2000

PF Pumping Frequency
PGM Programmed Maintenance
PI Polarization Index
PM Preventive Maintenance
ppm Parts Per Million
PT&I Predictive Testing and Inspection
RBOT Rotating Bomb Oxidation Test
RCFA Root-Cause Failure Analysis
RCM Reliability Centered Maintenance
RF Radio Frequency
RMS Root Mean Square
RPM Revolutions Per Minute
RTF Run to Failure
SAE Society of Automotive Engineers
SUS Saybolt Universal Seconds
TAN Total Acid Number
TBN Total Base Number
TDR Time Domain Reflectometry
TTR Transformer Turns Ratio
UT Ultrasonic
VLF Very Low Frequency
February 2000 B-177

B-178 February 2000

Appendix C—Bibliography
American Society of Non-Destructive Testing, Recommended Practice Number SNT-TC-1A,

Columbus, OH, 1992.
American Society for Testing and Materials, Philadelphia, PA.
ASTM D877 Dielectric Breakdown Voltage of Insulating Liquids Using Disk

Electrodes, April 1987.
ASTM D924 Power Factor, June 1993.
ASTM D974 Acid Neutralization by Color Indicator, March 1994.
ASTM D2285 Interfacial Tension of Electrical Insulating Oils of Petroleum
Origin against Water by the Drop-weight Method, November
1985.
ASTM 1289 Test Method for Density, Relative Density (Specific Gravity or
API Gravity) of Crude Petroleum and Liquid Petroleum Products
by Hydrometer Methods, February 1991.
ASTM D92 Flash and Fire Point by the Cleveland Open Cup, May 1991.
ASTM D97 Pour Point of Petroleum Oils, February 1994.
ASTM D1533 Water and Insulating Liquids, November 1989.
ASTM D445 Kinematic Viscosity of Transparent and Opaque Liquids, April
1989.
ASTM C1060-90 Thermographic Inspection of Insulation in Envelope Cavities In
Wood Frame Buildings, December 1990.
ASTM C1153-90 Standard Practice for the Location of Wet Insulation in
Roofing Systems Using Infrared Imaging, September 1990.
ASTM E1186-87 Standard Practices for Air Leakage Site Detection in Buildings,
May 1993.
ASTM E1149-90 Standard Terminology Relating to NDT by Infrared
Thermography, 1993
American Petroleum Institute, New York, NY
API 670 Vibration, Axial-Position Bearing-Temperature Monitoring

System, November 1993.
American National Standards Institute, New York, NY.
Annual Book of ASTM Standards, Section 5 (for lubricating oil tests), American Society for
Testing and Materials, Philadelphia, PA.
Chemistry & Technology of Lubricants, editors R.M. Mortier and S.T. Orszulik, VCH
Publishers, New York, NY, 1992.
February 2000 C-179

Contamination Control For The Fluid Power Industry, Second Edition, Fitch, E.C. and I.T.
Hong, Pacific Scientific Company, 1990, Silver Spring, MD.
Fuchs, Sheldon J. Complete Building Equipment Maintenance Desk Book, Second Edition,
Prentice-Hall, Englewood, NJ, 1992.
General Motors Specification A 1.0-1993, Laser Alignment Specification for New and Rebuilt
Machinery and Equipment, 1993.
Guideline For Infrared Inspection of Building Envelopes and Insulated Roofs, Infraspection
Institute, Shelburne, VT.
Guideline For Infrared Inspection of Electrical and Mechanical Systems, Infraspection Institute,
Shelburne, VT.
Guideline For Measuring and Compensating for Reflected Temperature, Emittance and
Transmittance, Infraspection Institute, Shelburne, VT.
Guideline For Measuring Distance/Target Width Ratios for Quantitative Thermal Imaging
Cameras, Infraspection Institute, Shelburne, VT.
Handbook of Lubrication, several volumes, Society of Tribologists and Lubrication Engineers,

Park Ridge, IL (contact at 840 Busse Highway, Park Ridge, IL 60068, (708) 825-5536).
Harris, Tedric A., Rolling Bearing Analysis, John Wiley & Sons, New York, NY, 1984.
Hewlett Packard Application Note 243-1, Effective machinery Measurement using Dynamic
Signal Analyzers, 1990.
Hewlett Packard Application Note 243, The Fundamentals of Signal Analysis, 1991.
Infraspection Institute, Guidelines for Infrared Inspection of Electrical and Mechanical Systems,
Shelburne, VT, 1993.
International Standards Organization, American National Standards Institute, 1430 Broadway,

New York, NY 10018.
ISO 6781 Thermal Insulation-Qualitative Detection of Thermal Irregularities

in Building Envelopes-Infrared Method, 1983.
ISO 3945 Mechanical Vibration of Large Rotating Machines with Speed
Range from 10-200 rev/s-Measurement and Evaluation of
Vibration Severity in Situ, 1985.
ISO 6781 Thermal Insulation- Qualitative Detection of Thermal
Irregularities in Building Envelopes - Infrared Method.
International Electrical and Electronic Engineers, New York, NY.
C-180 February 2000

Jackson, Charles, The Practical Vibration Primer. Gulf Publishing Company, Houston, Texas.
1979.
Lundberg, G. and Palmgren, A. Dynamic Capacity of Rolling Bearings, Acra Polytech,

Mechanical Engineering Series 1,R.S.A.E.E., No.3,7 (1947)
Machinery Oil Analysis, Larry A. Toms, Pensacola, FL, 1995. (Contact at 5018 High Pointe Dr.,
Pensacola, FL 32505-1825).
MIL-STB-2194 (SH), Infrared Thermal Imaging Survey Procedure for Electrical Equipment.
MIL-STD-167-1, Mechanical Vibrations of Shipboard Equipment, May 1974.
MIL-STD-740-2, Structureborne Vibratory Acceleration Measurements and Acceptance Criteria

of Shipboard Equipment, December 1986.
Mitchell, John S., Machinery Analysis and Monitoring, Penn Well Books, Tulsa, OK, 1981.
Moubray, John, Reliability-centered Maintenance, Butterworth-Heinemann Ltd. Oxford,

England, 1991.
National Electrical Manufacturers Association, Washington, DC.
National Fluid Power Association, NFPA T2.9.1-1972, Method for Extracting Fluid Samples
from the Lines of an Operating Hydraulic Fluid Power System for Particulate Particle
Contamination Analysis, 1992.
NETA MTS-1989, Maintenance Testing Specifications for Electric Power Distribution

Equipment and Systems, International Electric Testing Association.
Nowlan, F.S. and Heap, H.F. Reliability-Centered Maintenance, Dolby Access Press, San
Francisco, CA 1978.
Oil Analysis Seminar Coursebook, PdMA Corporation, Tampa FL, 1990.
Proceedings of the 44th Meeting of the Mechanical Failures Prevention Group, Current
Practices and Trends in Mechanical Failure Prevention, Vibration Institute, 1990.
SKF Engineering Data, SKF Industries, Inc. Philadelphia, PA, 1973
WWW Sites as of January 1999:
IEEE—Institute of Electrical and Electronics Engineers

http://www.ieee.org/
February 2000 C-181

ISO—International Organization for Standardization

http://www.iso.ch/
CIE—International Commission on Illumination

http://www.hike.te.chiba-u.ac.jp/ikeda/CIE/home.html
ANSI—American National Standards Institute

http://www.ansi.org/
NIST—National Institute of Standards and Technology

http://www.nist.gov/welcome.html
JIS—Japanese Industrial Standards

http://www.hike.te.chiba-u.ac.jp/ikeda/JIS/index.html
RCM Related Sites:
CSI http://www.compsys.com
Datastream http://www.dstm.com
Entek/IDR http://www.entekird.com
Flir Systems http://www.flir.com
HSB ReliabilityTech. http://www.hsbrt.com
Inframetrics http://www.inframetrics.com
Infraspection Institute http://www.infraspection.com
JB Sysytems http://www.jbsystems.com
Ludeca Inc. http://www.ludeca.com
Maintenance Technology Mag. http://www.mt-online.com
MIMOSA http://www.hsb.com/pcm/mimosa/mimosa.com
National Reliability Eng. Center http://www.enre.umd.edu/mainnojs.html
Monarch Monitoring http://www.easylaser.com
Penn State University http://wisdom.arl.psu.edu/
Plant Engineering Online http://www.manufacturing.net/magazine/planteng
PdMA http://www.pdma.com
Predict http://www.predict.com/
Raytek http://www.raytek.com
Reliability Center http://www.reliability.com
Reliability Magazine http://www.reliability-magazine.com
SPM Instrument http://www.spminstrument.se
C-182 February 2000

UE Systems http://www.uesystems.com
Vibra-Metrics http://www.vibrametrics.com
VibrAlign, Inc. http://www.vibralign.com/
Vibration Specialty http://www.vib.com/
Additional Resources - Magazines:

Reliability (423) 531-2193 www.reliability-magazine.com $49/yr
Maintenance Technology (847) 382-8100 www.mt-online.com Free
P/PM (702) 267-3970 $42/yr
Vibrations (630) 654-2340 $40/yr
Engineered Systems (248) 362-3700 www.esmagazine.com Free
Engineering Digest (708) 291-5222 Free
Plant Engineering www.planteng.com Free
Hydrocarbon Processing Free
Pumps and Systems (818) 885-6279 www.pumpzone.com Free
UE Service Partners (914) 347-5473 www.uesystems.com/service Free
Note: For additional information, please contact any RCM Team member.
February 2000 C-183

C-184 February 2000

Appendix D—Sources of PT&I Equipment, Services, and

Training
The vendors listed here are representative of those producing PT&I equipment, services, and/or
training.
VIBRATION MONITORING
Bently Nevada Corp. Computational Systems, Inc. (CSI)

1617 Water St. 835 Innovation Dr.
Minden, NV 89423 Knoxville, TN 37932
(702) 782-3611 (615) 675-2110
Predict/DLI Corp. Hewlett Packard
253 Winslow Way West 4 Choke Cherry Road
Bainbridge Island, WA 98110 Rockville, MD 20850
(206) 842-7656 (301) 670-4300
Entek/IRD, Inc. SKF Condition Monitoring
6150 Huntley Rd. 4141 Ruffin Road
Columbus, OH 43229 San Diego, CA 92123-1841
(614) 885-5376 (619) 496-3400
Structural Adhesives Bruel & Kajer
1 Dexter Drive 2364 Park Central Blvd.
Seabrook, NH 03874 Decatur, GA 30035
(603) 474-5541 (404) 987-9311
Wilcoxon Research Endevco Corporation
21 Firstfield Road (Suite 200) 30700 Rancho Viejo Road
Gaithersburg, MD 20878 San Juan Capistrano, CA 92675
(301) 330-8811 (714) 493-8181
Vibration Institute Technical Associates
6262 South Kingery Highway 347 North Caswell Road
Willowbrook, IL 60514 Charlotte, NC 28204
(708) 654-2254 (704) 333-9011
February 2000 D-185

Update International Massachusetts Institute of Technology

2103 South Wadsworth Boulevard Department of Materials Science and Engineering
Denver, CO 80227 77 Massachusetts Avenue (Bldg.8, Room 309)
(303) 986-6761 Cambridge, MA 02139
(617) 253-3300
Vitec, Inc.
23600 Mercantile Road
Cleveland, OH 44122
(216) 464-4670
OIL ANALYSIS & WEAR PARTICLE ANALYSIS
Analyst, Inc. Computational Systems, Inc. (CSI)

P.O. Box 955 835 Innovation Dr.
Torrance, CA 90509 Knoxville, TN 37932
(310) 212-7001 (615) 675-2110
Cleveland Technical Center Herguth Laboratories, Inc.

18419 Euclid Ave. 101 Corporate Place
Cleveland, OH 44112 Vallejo, CA 94590
(216) 383-8200 (800) 645-5227
Maintenance Technologies National Tribology Services, Inc.
58 Harvest Lane 245D Lynnfield St.
Milford, CT 06460 Peabody, MA 01960
(203) 877-3217 (508) 531-6123
Predict/DLI PdMA Corp.
9555 Rockside Rd., Suite 350 5909-C Hampton Oaks Pkwy.
Cleveland, OH 44125 Tampa, FL 33610
(216) 642-3223 (813) 621-6463
Southwest Spectro-Chem Labs
1009 Louisiana Ave.
So. Houston, TX 77587
(713) 944-3694
D-186 February 2000

INFRARED THERMOGRAPHY
AGEMA\Flir Infrared Systems, Inc. Cincinnati Electronics

550 County Avenue 7500 Innovation Way
Secaucus, NJ 07094 Mason, OH 45040-9699
Phone: (201) 867-5390 Phone: (513) 573-6100
Fax: (201) 867-2191 Fax: (513) 573-6290
Electro Physics Corp. Agema\Flir Systems, Inc.

373 Route 46 West, Bldg E 16505 S.W. 72nd Avenue
Fairfield, NJ 07004 Portland, OR 97224
Phone: (201) 882-0211 Phone: (503) 684-3731
Fax: (201) 882-0997 Fax: (503) 684-7046
Inframetrics, Inc. Insight Vision Systems, Inc.

16 Esquire Road 9836 Campbell Drive
N. Billerica, MA 01862 P.O. Box 13
Phone: (508) 670-5555 Kensington, MD 20895
Fax: (508) 667-2702 Phone: (301) 495-0211
Fax: (301) 495-2619
Ircon (formerly Square D Company) I.S.I. Group, Inc.

Infrared Measurement Division 211 Conchas SE
7301 North Caldwell Avenue Albuquerque, NM 87123
Niles, IL 60648 Phone: (505) 298-7646
Phone: (708) 967-5151 Fax: (505) 299-4926
Fax: (708) 647-0948
Land Infrared Raytek
2525 Pearl Buck Road, 1201 Shaffer Road, Box 1820
Bristol, PA 19007 Santa Cruz, CA 95061-1820
Phone: (215) 781-0700 Phone: (408) 458-1110
Fax: (215) 781-0723 Fax: (408) 458-1239
February 2000 D-187

ULTRASONICS—Airborne Passive
C.J. Analytical Engineering EPD Technology Corp.

R. R. 1, Box 355 12 W. Main St.
Francisco, IN 47649 Elmsford, NY 10523
(812) 782-3416 (914) 592-1234
ITI Industrial Leak Detection Services, Inc.

109 Terrace Hall Ave. 1009 Beach St.
Burlington, MA 01803 Annapolis, MD 21401
(617) 272-7233 (800) 345-7157
SDT USA Superior Signal Corp.

2985 Dutton Ave. #6 P.O. Box 96
Santa Rosa, CA 95407 Spotswood, NJ 08884
(707) 577-8053 (908) 251-0800
UE Systems Ultrasound of Florida

12 W. Main St. 31 Scott Dr.
Elmsford, NY 10523 Marietta, GA 30067
(914) 592-1220 (404) 977-2453
ULTRASONICS—Active Pulse
EPD Technology Corp. Kraut Kramer Branson

12 W. Main St. P.O. Box 350
Elmsford, NY 10523 Lewistown, PA 17044
(914) 592-1234 (717) 273-8805
Mgr., NDE Services Ultraimage International

Babcock & Wilcox Two Shaws Cove
Nuclear Power Division New London, CT 06320
3110 Odd Fellows Rd. (203) 442-0100
Lynchburg, VA 24501
(804) 847-3737
D-188 February 2000

CABLE TESTING
AVO International Char Services, Inc.

4651 S. Westmoreland Rd. P.O. Box 119
Dallas, TX 75237 Lebanon, PA 17042
(214) 333-3201 (717) 273-8805
ECAD Div. of CM Technologies Corp. NGI

1026 Fourth Ave. 1711 Elmhurst Rd.
Corapolis, PA 15108 Elkgrove Village, IL 60007
(412) 262-0734 (708) 437-6444
Project Services International

Robinson Plaza 3, Suite 300
Pittsburgh, PA 15205
(800) 860-0111
MOTOR CIRCUIT ANALYSIS
PdMA Corporation Savo Electronics Division

5909-C Hampton Oaks Parkway IdL, Inc.
Tampa, FL 33610 P.O. Box 1373
(813) 621-6463 Corvallis, OR 97339
(503) 758-7235
MOTOR CURRENT SIGNATURE ANALYSIS
Computational Systems, Inc. (CSI) ENTEK\IRD Scientific Corp.

835 Innovation Dr. 4480 Lake Forest Drive
Knoxville, TN 37932 Suite 316
(615) 675-2110 Cincinnati, OH 45242
(513) 563-7500
ENTEK\IRD Mechanalysis, Inc. Performance Technologies, Inc.

6150 Huntley Rd. 510 Little Creek Road
Columbus, OH 43229 Lynchburg, VA 24502
(614) 885-5376 (804) 237-2583
Predictive Maintenance Inspections Wyk Laboratories Scientific
February 2000 D-189

P.O. Box 432 Services & Systems, Inc.

Madison, AL 35758 7800 Govenors Drive
(205) 464-9679 P.O. Box 1008
Huntsville, AL 35807
(205) 837-4411
INSULATION TESTING/RESISTANCE TO GROUND
AVO International Amprobe Instrument Division of Core Ind.

4651 S. Westmoreland Rd. 630 Merrick Rd.
Dallas, TX 75237 P.O. Box 329
(214) 333-3201 Lynbrook, NY 11583
(516) 593-5600
Baker Instrument Co. Esterline Angus
2310 E. Prospect Rd. 1201 Main St.
Fort Collins, CO 80525 Indianapolis, IN 46224
(303) 221-3150 (317) 244-7611
Hipotronics John Fluke Mfg. Co.
P.O. Drawer A, Route 22 P.O. Box C9090
Brewster, NY 10509 Everett, WA 98206
(914) 279-8091 (206) 347-6100
Moore Industries PdMA Corporation
16650 Schoenborn St. 5909-C Hampton Oaks Parkway
Sepulveda, CA 91343 Tampa, FL 33610
(818) 894-7111 (813) 621-6463
VALVE AND BLADE TESTING
Liberty Technologies, Inc.

(215) 834-0330
POC: Tony Moffa, Sr.
D-190 February 2000

Appendix E—Vibration Criteria18
FORWARD
It is recommended that Vibration Certification of all new and rebuilt machinery and equipment
be a part of implementation of Reliability Centered Maintenance. Vibration analysis and
certification, as a part of machine performance evaluation will:
• Maximize part quality, machine productivity, tooling and machine life
• Minimize machine installation and set-up time
• Allow verification of machine performance and condition throughout the machine's life
This appendix provides engineering performance guidelines for use by Facilities Operations and
Maintenance as well as machinery and equipment builders during the design, development, and
building of new equipment and the rebuild of existing equipment. The vibration limits specified
by the user and acknowledged by the contractor establish a common goal of acceptability by
both parties. Such limits also enable contractors to provide evidence of the superiority and build
integrity of their product.
18
Acknowledgments: We wish to thank General Motors for the free use of their alignment and vibration
specifications, which are included in this document. This document may be copied in whole or in part for the use of
providing standards for maintainability of equipment.
February 2000 E-191

TABLE OF CONTENTS
1.0 PURPOSE
2.0 SCOPE
3.0 INSTRUMENTATION
3.1 FFT ANALYZER
3.2 MEASUREMENT SYSTEM ACCURACY
3.3 MEASUREMENT SYSTEM CALIBRATION
3.4 VIBRATION TRANSDUCERS
4.0 VIBRATION MEASUREMENT AXES DIRECTIONS

4.1 AXIAL DIRECTION
4.2 RADIAL DIRECTIONS
4.3 VERTICAL
4.4 HORIZONTAL
4.5 OTHER
5.0 VIBRATION MEASUREMENT LOCATIONS

5.1 CONVENTIONS
5.2 ACCESSIBILITY
5.3 LOCATION IDENTIFICATION
5.4 DOCUMENTATION
6.0 TRANSDUCER & MACHINE MOUNTING CONDITIONS

6.1 VIBRATION TRANSDUCER MOUNTING
6.2 MACHINE MOUNTING
7.0 TECHNICAL REQUIREMENTS

7.1 VIBRATION MEASUREMENT UNIT
7.2 FREQUENCY BANDS
7.3 LINE AMPLITUDE ACCEPTANCE LIMITS
7.4 BAND-LIMITED OVERALL AMPLITUDE ACCEPTANCE LIMITS
7.5 ALIGNMENT
7.6 BALANCING
8.0 MACHINE QUOTATION, CERTIFICATION AND ACCEPTANCE

8.1 QUOTATION
8.2 MEASUREMENT REQUIREMENTS FOR MACHINE CERTIFICATION
8.3 ACCEPTANCE
9.0 VIBRATION LEVEL LIMITS

9.1 ELECTRIC MOTORS
E-192 February 2000

9.2 FANS
9.3 PUMPS
9.4 GEARBOXES
9.5 DEFAULT VIBRATION LEVEL LIMITS
9.6 COMPLETE MACHINE
GLOSSARY
FIGURES
Figure 1 Measurement System Frequency Response
Figure 2 Vibration Measurement Axes Directions - Foot-Mounted
Figure 3 Vibration Measurement Axes Directions - End-Mounted
Figure 4 Order and Consecutive Numbering Sequence
Figure 5 Measurement Location Documentation Convention
Figure 6 Vibration Measurement Locations (a), (b), (c)
Figure 7 Frequency Bands
Figure 8 Balance Test Key Dimension
Figure 9.1 Maximum Allowable Vibration Limits for Electric Motors
Figure 9.2.1 Line Amplitude Acceptance Limits for Fans
Figure 9.2.2 Band-Limited Overall Amplitude Acceptance Limits for Fans
Figure 9.3.1 Line Amplitude Acceptance Limits for Positive Displacement & Centrifugal
Pumps
Figure 9.3.2 Band-Limited Overall Amplitude Acceptance Limits for Positive Displacement &
Centrifugal Pumps
Figure 9.4.1 Line Amplitude Acceptance Limits for Gearboxes
Figure 9.4.2 Band-Limited Overall Amplitude Acceptance Limits for Gearboxes
Figure 9.5.1 Default Line Amplitude Acceptance Limits for Non-Machine Tools
Figure 9.5.2 Default Band-Limited Overall Amplitude Acceptance Limits for Non-Machine
February 2000 E-193

TABLES
Table 1 Recommended Component Identification Symbols
Table 2 Vibration Measurement Units
Table 9.1.1 Motor Isolation Requirements
Table 9.1.2 Critical Speed Offset Requirements
Table 9.1.3 Maximum Allowable Vibration Levels for Electric Motors
Table 9.1.4 Motor Nameplate Vibration Data requirements
Table 9.2 Maximum Allowable Vibration Levels for Fans
Table 9.3 Maximum Allowable Vibration Levels for Positive Displacement & Centrifugal Pumps
Table 9.5 Maximum Allowable Vibration Levels for Non-Machine Tools
E-194 February 2000

VIBRATION STANDARD
FOR NEW AND REBUILT MACHINERY AND EQUIPMENT
1.0 PURPOSE
The purpose of this standard is to:
• Reduce operating costs by establishing acceptable vibration levels for new and
rebuilt rotating machinery and equipment.
• Improve the life and performance of rotating machines and equipment.
• Provide a uniform procedure for evaluating the vibration characteristics of a

machine for certification and acceptance.
2.0 SCOPE
This standard establishes:
• Acceptable limits for vibration levels generated by new and rebuilt rotating
machinery and equipment.
• Measurement procedures--including standardized measurement axis directions

and locations, calibration and performance requirements of instrumentation, and
procedures for reporting vibration data for machine certification and acceptance.
3.0 INSTRUMENTATION REQUIREMENTS
Vibration measurements will be made with an FFT analyzer. The type, model, serial
number(s) and latest certified calibration date of all equipment used in the measurement
of vibration levels for machine certification, shall be recorded and made available upon
request.
3.1 FFT ANALYZER
• The FFT Analyzer shall be capable of a line resolution bandwidth ∆f = 300

CPM for the frequency range specified for machine certification unless this
restriction would result in less than 400 lines of resolution, in which case the
requirement defaults to 400 lines of resolution. (Higher resolution may be
required to resolve "Side Bands," or in Band 1 to resolve machine vibration
between 0.3X and 0.8X Running Speed.)
February 2000 E-195

• The Dynamic Range shall be a minimum of 72 dB.
• The FFT analyzer shall be capable of applying a Hanning window.
• The FFT analyzer shall be capable of linear non-overlap averaging.
• The FFT analyzer shall have anti-aliasing filters.
3.2 MEASUREMENT SYSTEM ACCURACY
The measurement system (FFT analyzer, cables, transducer and mounting) used to
take vibration measurements for machine certification and acceptance shall have a
measurement system Amplitude accuracy over the selected frequency range as
follows:
• For displacement and velocity measurements ±l0% or ±1 dB.

• For acceleration measurements ±20% or ±1.5 dB.
SYSTEM FREQUENCY RESPONSE
Amplitude
+R%
Relative
0
Response
-R%
Linear Measurement Range
R = 10% for Displacement & Velocity

R = 20% for Acceleration
Figure 1. Measurement System Frequency Response
3.3 MEASUREMENT SYSTEM CALIBRATION
Vibration equipment (transducer, preamplifier, FFT analyzer, recorder and

connecting cable) used to take vibration measurements for machine certification
and acceptance must be calibrated by a qualified instrumentation laboratory in
accordance with Sections 5.1 and 5.2 of ANSI S2.17-1980 "Technique of
Machinery Vibration Measurement" within one (1) year prior to the date of
machine certification.
E-196 February 2000

Calibration shall be traceable to the National Institute of Standards and

Technology (NIST) in accordance with ISO 10012-1/1992 “Quality assurance
requirements for measuring equipment - Part 1: Metrological confirmation
systems for measuring equipment.”
3.4 VIBRATION TRANSDUCERS
3.4.l An accelerometer shall be used in the collection of data for machine

certification and acceptance. The accelerometer must be selected and
attached to the machine in such a way that the minimum frequency (Fmin)
and maximum frequency (Fmax) as specified in Section 9 or specified
otherwise by the purchaser, are within the usable frequency range of the
transducer and can be accurately measured (reference recommendations of
pickup manufacturer and/or Section 6.3, ANSI S2.17-1980).
3.4.2 The mass of the accelerometer and its mounting shall have minimal
influence on the frequency response of the system over the selected
measurement range. (Typical mass of accelerometer and mounting should
not exceed 10 % of the dynamic mass of the structure upon which the
accelerometer is mounted.) Reference Appendix for Dynamic Mass
definition and Procedure to Determine Mass Effect
3.4.3 Integration is acceptable as a means of converting acceleration

measurements to velocity or displacement, or for converting velocity
measurements to displacement.
4.0 VIBRATION MEASUREMENT AXIS DIRECTIONS
4.1 AXIAL DIRECTION (A) shall be parallel to the rotational axis of the machine
(reference Figures 2 and 3.
4.2 RADIAL DIRECTIONS (R) shall be:
• at 90° (perpendicular) relative to the shaft (rotor) centerline.
4.3 VERTICAL shall be in a radial direction:
• on a machine surface opposite the machine mounting plate (reference Figure

2).
For motors or pumps that are end mounted, vertical readings shall be taken in a
radial direction relative to axial readings on a surface opposite the machine to
which the motor or pump is attached (reference Figure 3).
4.4 HORIZONTAL shall be in a radial direction:
February 2000 E-197

• at a right angle (90°) from the vertical readings:
• In the direction of the shaft (rotor) rotation (Reference Figure 2 and 3).
4.5 OTHER:
• Any radial direction other than Horizontal or Vertical as defined in Sections

4.3 and 4.4.
A
MACHINE TOP VIEW
H
A = AXIAL
V = VERTICAL
H = HORIZONTAL
V
A
H
MACHINE SIDE VIEW V
A
Figure 2 Vibration Measurement Axes Directions - Foot Mounted
DIRECTION V
OF SHAFT
ROTATION
PUMP H
AND/OR DIRECTION
MACHINE MOTOR OF SHAFT
ROTATION PUMP AND/OR MOTOR
H
V
A MACHINE
Figure 3 - Vibration Measurement Axes Directions - End-Mounted
5.0 VIBRATION MEASUREMENT LOCATIONS
E-198 February 2000

Required measurement positions and orientations on a machine's surface at which

vibration measurements are to be taken shall be determined by mutual agreement of the
purchaser and the contractor, and shall meet the following requirements:
5.1 CONVENTIONS
Follow the convention specified in Sections 4.0 and 5.0, unless specified
otherwise by the purchaser.
5.1.1 If an obstruction or safety prevents locating a transducer as specified, locate as

close as possible to the standardized position.
5.1.2 Measurement locations used for machine certification and acceptance shall be
identified on the machine layout drawing and/or machine as mutually agreed
upon by the purchaser and the contractor.
5.1.3 Vibration measurement locations shall be on a rigid member of the machine,

as close to each bearing as feasible. Bearing housings, bearing pedestals,
machine casings or permanently mounted pickup mounting blocks are
examples of suitable mounting locations.
5.1.4 Vibration measurement location shall NOT be on a flexible cover or shield

such as the fan cover on an electric motor or a sheet-metal belt guard.
5.2 ACCESSIBILITY
5.2.1 Guarding must be designed to allow accessibility to all measurement locations

(Reference Section 5.7).
5.2.2 In the event that vibration monitoring points will be rendered inaccessible
after the machine is built or access to the measurement points would present a
safety problem during measurement, the purchaser shall be contacted to
determine if Permanently mounted transducers are to be installed.
5.3 LOCATION IDENTIFICATION
Measurement locations shall be numbered consecutively from 1 to N in the

direction of power flow per the following:
Position 1 designates the "out-board" Starting Power Point bearing location of the
driver unit of the machine. Position N designates the bearing location at the
"terminating" Power Point bearing location of the driven machine. (Reference
Figure 4)
February 2000 E-199

1(V,H,A) 2(V,H,A) 3(V,H,A) 4(V,H,A)
MOTOR GEARBOX 5(V,H,A) 6(V,H,A)
MACHINE
POWER FLOW PROCESS

FLOW
7(V,H,A) 8(V,H,A) DIRECTION
MACHINE #2
Figure 4 Order and Consecutive Numbering Sequence
5.4 DOCUMENTATION
Measurement locations documented for certification and acceptance on the

machine layout drawing and on any vibration data submitted shall follow the
following convention as shown in Figure 5:
• Station or Machine
• Component (Reference Table 1)
• Position
• Orientation
COMPONENT
EQUIPMENT ID
POSITION
ORIENTATION
RP0645-00 M O V
Figure 5 Measurement Location Documentation Convention
E-200 February 2000

GBX = Gear Box BSH = Bushing MTR = Motor

FAN = Fan PMP = Pump JS = Jackshaft
IP = Idler Pulley CL = Clutch
Other Component Symbols not listed above should be agreed upon by the machine tool builder and the
purchaser on an as-needed basis
Table 1 Recommended Component Identification Symbols
6.0 TRANSDUCER & MACHINE MOUNTING CONDITIONS
6.1 VIBRATION TRANSDUCER MOUNTING
At the designated measurement positions, suitable surfaces shall be provided such

that the mounted transducer will attach securely.
6.1.1 Hand-held pickups are not acceptable for measurement by this

specification.
6.1.2 For a magnetic base mounted transducer the location on a machine's

surface at which vibration measurements are to be taken shall be
machined, if necessary, such that the magnet base can be attached firmly
without "rocking."
6.1.3 For a stud mounted transducer the machine's surface at which vibration
measurements are to be taken shall be in accordance with that specified by
the transducer manufacturer (torque, grease, etc.) Designated transducer
type to be specified by the purchaser.
6.1.4 If an adhesive is used to attach either the transducer or a magnetic

mounting pad, the upper frequency limit of the transducer shall be reduced
by 20% of the manufacturer's stated resonance for "hard" adhesives and by
50% of the manufacturer's stated resonance for "soft" adhesives.
Transducer manufacturer's specifications should be consulted.
6.1.5 The vibration transducer as mounted must be such that the measurement
system Amplitude accuracy over the selected frequency range equals or
exceeds the requirements specified in Section 3.1.
6.2 MACHINE MOUNTING
6.2.1 Where a machine can be tested as an individual unit (e.g. motor, spindle,
etc.) the machine must be mounted as specified in Section 9.
6.2.2 Where an individual machine can be tested only as an assembled unit (e.g.
motor/pump, motor/fan, etc.), the machine mounting conditions shall be as
February 2000 E-201

equivalent as possible/feasible to those to be encountered upon installation

at the purchaser's site.
1(H,V) 2(H,V,A)
1(H,V,A)
2(H,V)
4(H,V,A) 3(H,V,A)
3(H,V,A)
4(H,V,A)
MOTOR & FAN
(a) FLUID TRANSFER PUMP
(b)
Motor: 1200 RPM

38 T
1200 RPM
G1 (H,V,A) G2 (H,V,A) Motor
45,600 CPM Mesh
MO (H,V) MI (H,V,A)
50 T 35 T
912 RPM
G3 (H,V,A) G4 (H,V,A) 31,920 CPM

Mesh
47 T
679 RPM
Motor - Gear Box System

Gear Reducer
(c)
Figure 6 Vibration Measurement Locations
E-202 February 2000

7.1 VIBRATION MEASUREMENT UNITS
Vibration data for machine certification and acceptance shall be expressed in the
following measurement units:
Frequency Hertz (cycle/sec) or Cycle/Minute (CPM)

Rotational Speed Revolutions per Sec (RPS) or Revolutions per Minute
(RPM)
Amplitude METRIC ENGLISH
• Displacement (Peak-to-Peak)* Micrometers Inch (Also Mil in
U.S.)**
• Velocity (Peak)* Millimeter/sec Inch/sec
• Acceleration (Peak)* Meter/sec2 g’s
* Can also use Root-Mean-Square ** 1 "Mil" = 0.001
(RMS) inch
Table 2 Vibration Measurement Units
The "Peak" and "Peak-to-Peak" Vibration Amplitude Measurements will be a

Calculated Peak not a True Peak. The Calculated Peak will be derived from the
RMS level based on the following equations:
Peak (P) = 1.414 x RMS

Peak-to-Peak (P-to-P) = 2 x (P) = 2 x 1.414 x RMS
If a "True Peak" is required, the units of vibration measurement will be designated

by the words "True Peak".
7.2 FREQUENCY BANDS
The frequency range of measurement shall be divided into sub-groups called

bands. The Fmin and Fmax for each band will be defined in units of frequency or
orders of running speed of the machine.(Ref. Figure 7)
7.2.1 Mandatory Bands Band 1 shall be (0.3 - 0.8) X Running Order. Band 2
shall be (0.8 - 1.2) X Running Order. Band 3 shall be (1.2 - 3.5) X
Running Order
7.2.2 Other Bands
Bands 4 through N shall be defined by the specific machine application.
February 2000 E-203

To be Determined for
Specific Machine Classification
A
M
P BAND BAND BAND BAND BAND BAND
L 1 2 3 4 5 N
I
T
U
D
E
0.3 0.8 1.2 3.5 Fmax

1x 2x 3x 4x
ROTATIONAL SPEED ORDERS
Figure 7 Frequency Bands
7.3 LINE AMPLITUDE ACCEPTANCE LIMITS
For vibration level limits specified in terms of "LINE AMPLITUDE

ACCEPTANCE LIMITS":
• A line of resolution will have a band width ∆f = 300 CPM unless specified
otherwise (Reference Section 7.4 requirement for total energy in a peak), or
unless the ∆f = 300 CPM restriction would result in less than 400 lines of
resolution over the frequency range specified for certification, in which case
the resolution requirement will default to 400 lines. (Greater resolution may
be required to resolve "Side Bands," or in Band 1 to resolve machine
vibration between 0.3X and 0.8X Running Speed.
• The maximum amplitude of any line of resolution contained within a band

shall not exceed the Line Amplitude Acceptance Limit for the Band.
7.4 BAND-LIMITED OVERALL AMPLITUDE ACCEPTANCE LIMITS
For vibration level limits specified in terms of "BAND-LIMITED OVERALL

AMPLITUDE ACCEPTANCE LIMITS" the Total vibration level "A" in a band,
E-204 February 2000

as defined by the following equation, shall not exceed the Overall Amplitude
Acceptance Limit specified for the Band
∑ A
2
i
A = i =1
1 .5
A = Overall vibration level in the Band
Ai = Amplitude in the ith line of resolution in the Band
(I=1) = The first line of resolution in the Band
(i=N) = The last line of resolution in the Band
N = The number of lines of resolution in the Band
If the total energy in a peak is to be measured, a minimum of 5 lines of resolution

must be used and the peak must be centered in the band.
7.4.1 If a line of resolution is coincidental with the Fmin/Fmax Of two adjacent

bands, that line of resolution will be included in the band having the
lowest acceptance level limit.
7.4.2 The amplitude range sensitivity of the FFT Analyzer shall be set to the
maximum input sensitivity possible without overloading such that the
actual measurement uses at least 60 dB of the Dynamic Range.
7.4.3 Certification will be based on:
• Hanning Window.
• Four (4) averages (Linear non-overlapping).
7.4.4 The transducer mounting shall be such that the measurement system
Amplitude accuracy over the selected frequency range equals or exceeds
the requirements specified in Section 3.1. This may require the use of
more than one accelerometer where potentially high frequencies might
occur (such as gear mesh or harmonics of gear mesh) along with lower
frequencies (such as due to unbalance, misalignment, looseness, etc.)
7.5 ALIGNMENT
All coupled rotating machines consisting of consecutive shafts connected through

a coupling (whether rigid or flexible) shall be aligned within the tolerances
specified by the purchaser in the "Request for Quote." If the Purchaser does not
specify an alignment tolerance, the requirements of this Standard defaults to the
tolerance limits specified in Specification No. A 1.0-199X, LASER
ALIGNMENT SPECIFICATION FOR NEW AND REBUILT MACHINERY
AND EQUIPMENT."
February 2000 E-205

Consideration shall be given to any "thermal growth" that may occur during the
normal operation of the machine that would cause the machine to "grow out of
alignment" to the extent that the alignment tolerances of this specification would
not be met.
7.6 BALANCING
7.6.1 STANDARD KEY. For rotating machines and machine components with
a keyed shaft, balancing will achieved using a standard one-half key in the
key seat in accordance with ISO 8821-1989. If a "full key",
corresponding to the half key used for balancing, is not provided with the
rotating machine, a tag, as shown in Figure 8, will be attached to the
machine indicating the dimension of the key used to perform the balance
test.
A A = Key length as used for balancing this rotor

B (usually in the form of a “half depth”
B = Key length as used for balancing the attached

rotor (such as coupling half, pulley, fan, etc.)
This is determined by measuring the attached.
rotors keyway length at its hub.
Final Key Length

(A+B)/ 2
7.6.2 The use of solder or similar deposits to achieve rotor balance is not
acceptable. Any parent metal removed to achieve dynamic or static
balance shall be drilled out in a manner which will maintain the structural
integrity of the rotor.
8.0 MACHINE QUOTATION, CERTIFICATION, AND ACCEPTANCE
8.1 QUOTATION
8.1.1 The Quotation shall specify that the equipment will meet the applicable
vibration level limits in Section 9 of this Specification - or the vibration
level limits (if different from Specification V1.0 (Latest Version) specified
by the purchaser in the "Request for Quote."
E-206 February 2000

8.1.2 The Quotation shall state the applicable specification vibration level limits
being quoted.
8.1.3 Any additional costs required to meet the specification limits shall be
grouped in a separate section of the Quotation and titled "VIBRATION
LIMITS." Costs must be itemized and sufficiently detailed to permit a
complete evaluation by the Purchaser.
8.2.1 Vibration measurements shall:
8.2.1.1 Be the responsibility of the supplier unless specified otherwise

by the purchaser.
8.2.1.2 Be performed by technically qualified person who is trained and

experienced in vibration measurement. The technical
qualifications of the person doing the vibration certification shall
be submitted as a part of the machine vibration certification data.
8.2.1.3 Be taken with the machine operating as specified in Section 9.

Where "no load" is specified, no actual work is to be taking place
during collection of machine vibration data. Where "rated load"
is specified, rated operating load--either actual or simulated--will
be applied during collection of machine vibration data.
8.2.1.4 Prior to taking vibration measurements, the machine will be

"run-in" until it reaches operating speed and thermal stability
8.2.2 Vibration Signatures as required by Section 9 of this specification, shall be
submitted to the Maintenance organization or other authorized
representative before acceptance of the machinery or equipment being
purchased will be authorized.
8.2.3 Vibration data for machine certification shall be measured during "run-off'
at the vendor's facility. Where it is impractical to set-up and test a
complete machine at the vendor's facility, arrangements shall be made to
perform the test at the purchaser's facility. Under this circumstance,
shipment of the equipment does not relieve the vendor of the
responsibility for meeting the specified vibration level limits.
8.2. 4 The purchaser shall have the option to verify vibration data of equipment
during machine "run-off' at the vendor's test site prior to shipment - or at
the plant site per Section 8.2.3 - prior to final acceptance authorization.
8.2.5 The machine layout drawing shall be submitted as a part of the Machine
February 2000 E-207

Vibration Certification. Vibration measurement locations on the

machine's surface at which vibration measurements are taken shall be
designated on the drawing per Section 5.7 requirements. At the option of
the purchaser, Shaft speeds (RPM), gear type and number of gear teeth,
gear mesh frequencies (CPM), bearing manufacturer's name, bearing type
number and class, shall be identified on the machine layout drawing.
Where gearboxes are involved, an insert such as illustrated in Figure 6 - c
shall be included on the machine layout drawing.
8.3 ACCEPTANCE
Authorization for machine/equipment acceptance based on the vibration limits of

this specification requires signature by the purchaser's authorized representative.
A copy of the acceptance must be sent to the plant's Purchasing department before
final acceptance is authorized.
9.0 VIBRATION LEVEL LIMITS
9.1 ELECTRIC MOTORS -- Refer to Section 9.1 Vibration Standards for Electric
Motors."
9.2 FANS -- Refer to Section 9.2 Vibration Standards for Fans."
9.3 PUMPS -- Refer to Section 9.3 Vibration Standards for Pumps."
9.4 GEARBOXES -- Refer to Section 9.4 Vibration Standards for Gearboxes."
9.5 DEFAULT VIBRATION LEVEL LIMITS -- Refer to Section 9.5 Vibration

Standard Default Limits."
9.6 COMPLETE MACHINE ASSEMBLY
A complete machine is defined as the entire assembly of components, sub-

components, and structure, which is purchased to perform a specific task(s). On a
Complete Machine Assembly with all individual components operating in their
normal operating condition, mode, and sequence, the Component Vibration Level
Limits for the complete machine acceptance are the same as when the component
is tested individually. Where assembled component levels exceed the acceptable
limits, the cause will be identified, if possible, and a decision to correct or accept
mutually agreed upon by purchaser and contractor.
E-208 February 2000

SECTION 9.1
VIBRATION STANDARDS FOR ELECTRIC MOTORS

9.1.1. ELECTRICAL MOTOR REQUIREMENTS
9.1.1.1 Motors will be defined by four (4) categories:
Standard motor.......Utility Operations
Special motor..........Semi-Finish Operations
Precision motor.......Finish Operations
Other motor............Per agreement by vendor and the Government
9.1.1.2 The frequency range for motor certification will be from Fmin = 0.3 X
Running Speed (synchronous speed) to Fmax = 120,000 CPM (2,000 Hertz)
9.1.1.3 Alternating current motors will be tested at rated voltage and frequency, and
no load. Single speed alternating current motors will be tested at synchronous
(running) speed. A multi-speed alternating current motor will be tested at all
its rated synchronous (running) speeds. Direct current motors will be tested at
their highest rated speed. Series and universal motors will be tested at
operating speed.
9.1.1.4 MOTOR ISOLATION
9.1.1.4.1 Method of Motor Isolation for Measuring Vibration
Place the motor on an elastic mounting so proportioned that the up
and down natural frequency shall be at least as low as 25 percent of
the test speed of the motor. To accomplish this it is required that the
elastic mounting be deflected downwards at least by the amounts
shown in the Following table due to the weight of the motor. When
a flexible pad is used the compression shall in no case be more than
50 percent of the original thickness of the flexible pad; otherwise the
supports may be too stiff.
MOTOR SYNCHRONOUS SPEED ISOLATION PAD
(RPM) COMPRESSION
(INCHES)
900 1
1200 9/16
1800 1/4
3600 1/16
7200 1/64
Note: The required deflection is inversely proportional to the speed squared.
Table 9.1.1 Motor Isolation Requirements
9.1.1.4.2 All new and rebuilt motors shall conform to the vibration limits
specified in Table 9.1 when tested in accordance with this
specification.
February 2000 E-209

9.1.1.5 CRITICAL SPEED

Completely assembled motors shall have a percentage separation between the
rotor shaft first actual critical speed and the rated motor speed as specified:
FIRST ACTUAL
CRITICAL SPEED LOCATION
ROTOR DESIGN
Rigid Shaft At least 25% Above Rated Motor Speed
Flexible Shaft Maximum of 85% of Motor Speed
Table 9.1.2 Critical Speed Offset Requirement
9.1.1.6 LIMITS
9.1.1.6.1 All electrical motors defined by NEMA Standard MG-1-1993 Section

I "Classification According to Size,” Small (fractional), Medium
(integral) and Large Machines, shall meet the following requirements:
9.1.1.6.1.1 The Velocity Amplitude (Inch/sec-Peak) of any line of

resolution, measured at bearing locations (ref. Section 5) in
any direction (ref. Section 4) shall not exceed the Line-
Amplitude Band Limit values specified in Table 9.1 and
graphed in Figure 9.1 when determined in accordance with
Section 7.2.1 using the frequency range defined in Section
9.1.1.2.
9.1.1.6.1.2 The Acceleration Overall Amplitude (g's Peak) at bearing

locations (ref. Section 5) in any direction (ref. Section 4)
shall not exceed the Band-Limited Overall Amplitude
Acceptance Limit values specified in Table 9.1 and graphed
in Figure 9.1, when determined in accordance with Section
7.2.2 using the frequency range defined in Section 9.1.1 2.
E-210 February 2000

VELOCITY LINE-AMPLITUDE BAND LIMITS

BAND FREQUENCY STANDARD SPECIAL PRECISION
RANGE (CPM) (INCH/SEC - (INCH/SEC - (INCH/SEC -
PEAK) PEAK) PEAK)
1 0.3 x RPM 0.04 0.04 0.02
0.8 x RPM
2 0.8 x RPM 0.075 0.04 0.02
1.2 x RPM
3 1.2 x RPM 0.04 0.04 0.01
3.5 x RPM
4 3.5 x RPM 0.03 0.03 0.01
8.5 x RPM
5 8.5 x RPM 0.03 0.03 0.005
60,000 CPM
6 60,000 CPM 0.03 0.03 0.005
120,000 CPM
ACCELERATION BAND-LIMITED OVERALL AMPLITUDE LIMITS

BAND FREQUENCY STANDARD SPECIAL PRECISION
RANGE (CPM) (g’s PEAK) (g’s PEAK) (g’s PEAK)
1 0.3 x RPM - 0.5 0.5 0.25
120k
TABLE 9.1.3 Maximum Allowable Vibration Levels For Electric Motors
9.1.2. ELECTRICAL MOTOR CERTIFICATION
9.1.2.1 The amplitude of vibration at bearing locations (Ref. Section 5) in any direction
(radial and axial as defined in Section 4) shall not exceed the values listed in
Table 9.1.
9.1.2.2 Vibration signatures of velocity and acceleration, and a listing of the maximum
peak velocity in each band for vibration measurements taken at position 1
horizontal, position 2 vertical, and position 3 axial shall be submitted as part of
the motor certification. The data shall be identified with the Motor Serial
Number, Frame Number, Model Number, Horsepower and Synchronous speed.
February 2000 E-211

STANDARD MOTOR SPECIAL MOTOR

Velocity LINE AMPLITUDE ACCEPTANCE Velocity LINE AMPLITUDE ACCEPTANCE
(in/sec) (in/sec)
LIMITS LIMITS
.10 .10
.09 .09
.075
.08 .08
.07 .07
.06 .06
.05 .05
.04 .04 .04 .04 .04
.04 .04
.03 .03 .03 .03 .03 .03
.03 .03
BAND BAND BAND BAND BAND BAND BAND BAND BAND BAND BAND BAND
.02 1 2 3 4 5 6 .02 1 2 3 4 5 6
.01 .01
1 2 3 4 5 6 7 8 9 10 11 Fmax = 1 2 3 4 5 6 7 8 9 10 11 Fmax =
cpm cpm
RUNNING SPEED ORDERS RUNNING SPEED ORDERS

STANDARD MOTORS---UTILITY OPERATIONS SPECIAL MOTORS---SEMI FINISH OPERATIONS
PRECISION MOTOR BAND-LIMITED OVERALL

Velocity LINE AMPLITUDE ACCEPTANCE AMPLITUDE
Acceleration
ACCEPTANCE LIMITS
(in/sec)
LIMITS (g’s)
1.0
0.9
.025 0. BAND 1
.02 .02 8
0.7
.020 0.6
.015 0.5
.01 .01
0.4 0.5g STANDARD MOTOR & SPECIAL MOTOR
.010
0.3
.005 .005
.005 0.2
BAND BAND BAND BAND BAND BAND
1 2 3 4 6 0.25g PRECISION MOTOR
5 0.1
1 2 3 4 5 6 7 8 9 10 11 Fmax = 1 2 3 4 5 6 7 8 9 10 11 Fmax =
cpm cpm
RUNNING SPEED ORDERS FREQUENCY - CPM

PRECISION MOTORS--UTILITY
Figure 9.1 Maximum Allowable Vibration Limits for Electric Motors
E-212 February 2000

9.1.2.3 The motor nameplate shall carry the following designation:
FOR STANDARD “0.075 IN/S MAX VIB 1X”

FOR SPECIAL “0.04 IN/S MAX VIB 1X”
FOR PRECISION “0.02 IN/S MAX VIB 1X”
FOR OTHER * “____ IN/S MAX VIB 1X”
* per agreement by vendor and NASA
Table 9.1.4 Motor Nameplate Vibration Data Requirements
9. 1.2.4 Vibration data and signatures must be submitted with the motor to the NASA
Maintenance organization or other authorized representative before acceptance
of the motor will be authorized.
9. 1.2.5 Motors not meeting the certification shall be rejected.
February 2000 E-213

SECTION 9.2
VIBRATION STANDARDS
FOR FANS
9.2.1 FAN DEFINITION
All non-positive displacement air handling units including Induced Draft (ID) Fans,
Forced Draft (FD) Fans, Overhung Fans, Centerhung Fans, Centrifugal, Vaneaxial,
Tubeaxial, Blowers, etc.
9.2.2 BALANCING
9.2.2.1 Permanently attached balancing weighs must be secured by welding, bolting,

pop-riveted, or of a "clip-on" design.
• If bolted, a hardened bolt must be used in conjunction with a mechanical

locking device (e.g. lock washer or lock nut).
• Clip-on" balancing weights can only be used on centrifugal type fans

and must be located and attached on the ID pitch of the blades such that
the rotational motion of the fan creates a positive seating of the "clip-on"
weight against the fan blade.
• Balancing weights and method of attachment must be stable at fan

operating temperature, and of a material compatible with the parent
material of the fan to which the balancing weight is attached.
§ NOTE: THE USE OF STICK ON LEAD WEIGHTS IS NOT

ACCEPTABLE
9.2.2.2 Any parent metal removed to achieve dynamic or static balance shall be drilled
out in a manner which will maintain the structural integrity of the rotor or
sheave.
9.2.2.3 Access to the fan rotor for field balancing shall be designed in to the system.
NOTE: It is recommended that components (rotor, shafts, sheaves) be balanced individually and then trim balanced
as a total assembly.
9.2.3 SHAFT TOLERANCE
Fan shaft diameter shall meet bearing manufacturer specifications for shaft tolerances.
E-214 February 2000

9.2.4 RESONANCE
Natural frequencies of the completely assembled fan unit shall not be excited at the
operating speed. (Running speed should be at least 25% removed from a natural
frequency of the system.)
9.2.5 LIMITS
9.2.5.1 New and Rebuilt/Repaired Fans shall conform to the vibration limits specified
in Table 9.2 when operating at specified system CFM and Fan Static Pressure.
9.2.5.2 The frequency range for fan certification shall be from Fmin = 0.3 X Running
Speed of Fan to 60,000 CPM for velocity and to 120,000 CPM for
acceleration.
9.2.5.3 For fan speeds up to 3600 RPM, the maximum velocity amplitude (inch/sec-
Peak) of vibration at bearing locations (ref. Section 5) in any direction (as
defined in Section 4) shall not exceed the Line Amplitude Band Limit values
specified in Table 9.2 and graphed in Figure 9.2.1 when determined in
accordance with Section 7.2.1 using the frequency range defined in Section
9.2.5.2.
9.2.5.4 For fan speeds up to 3600 RPM, the Band-Limited Overall vibration level of
acceleration (g's Peak) at bearing locations (ref. Section 5) in any direction (as
defined in Section 4) shall not exceed the Band-Limited Overall Amplitude
Acceptance Limit values specified in Table 9.2 and graphed in Figure 9.2.2,
when determined in accordance with Section 7.2.2 using the frequency range
defined in Section 9.2.5.2.
9.2.5.5 Acceptance limits for fans running over 3600 RPM shall be specified by the
purchaser.
February 2000 E-215

BAND FREQUENCY RANGE VELOCITY LINE AMPLITUDE BAND LIMITS

(INCH/SEC PEAK)
1 0.3 x RPM min 0.04 DIRECT COUPLED
0.8 x RPM fan 0.075 BELT DRIVE
2 0.8 x RPM fan 0.075
1.2 x RPM fan/motor
3 1.2 x RPM fan/motor 0.04
3.5 x RPM fan/motor
4 3.5 x RPM fan/motor 0.03
to Fmax = 60,000 CPM
ACCELERATION BAND LIMITED OVERALL
AMPLITUDE LIMITS
(g’s PEAK)
1 0.3 x RPM min 0.5
to Fmax = 120,000 CPM
RPM min = Lowest system speed (e.g. Belt speed if Belt Driven, Fan speed if direct drive coupled
RPM fan/motor = Fan or motor speed whichever is greater (IN/SEC)
Table 9.2 Maximum Allowable Vibration Levels For Fans
LINE AMPLITUDE ACCEPTANCE LIMITS
.10
V .09
E .08 .075 .075
L .07
O .06
C .05 .04
. 04 .03
I .04
T .03
Y .02
BAND 1 BAND 2 BAND 3 BAND 4
.01
0.3 RPM 1 2 3 4 10 Fmax =60K

(IN/SEC)
FREQUENCY -
Figure 9.2.1 Line Amplitude Acceptance Limits for Fans
E-216 February 2000

BAND-LIMITED OVERALL AMPLITUDE ACCEPTANCE LIMITS
A
C 1.0
C 0.9
E 0.8
L 0.7
E 0.6 0.5g (Peak)
R 0.5
A 0.4
T 0.3
I 0.2 BAND 1
O 0.1
N
Fmax = 120K
FREQUENCY - CPM
Figure 9.2.2 Band Limited Overall Amplitude Acceptance Limits for Fans
9.2.6 OTHER REQUIREMENTS
9.2.6.1 Variable speed or adjustable sheaves shall not be used in the final installation.
9.2.6.2 Drive sheave and driven sheave should differ in size by 20 % or more to avoid
"beat" vibration.
February 2000 E-217

SECTION 9.3
VIBRATION STANDARDS
FOR PUMPS
9.3.1 Pumps shall be defined in two (2) categories:
• Positive Displacement --including, but not limited to Piston, Gear, and Vane.
• Centrifugal.
9.3.2 Operating Conditions
9.3.2.1 Non-cavitating, non-separating condition
9.3.2.2 No piping strain
9.3.2.3 Shaft coupling aligned
9.3.2.4 Straight suction pipe to pump. (Reference Hydraulic Institute Standard)
9.3.2.5 Certification shall be performed while pumps are operating within design
specifications
9.3.3 LIMITS FOR POSITIVE DISPLACEMENT & CENTRIFUGAL PUMPS
9.3.3.1 For purposes of Line Amplitude evaluations a "PUMPING FREQUENCY"

(PF) band will be established. The PF Band will be centered on the Pumping
Frequency (Number of pumping elements X Pump RPM). The band will
extend + 2 lines of resolution on either side of the line of resolution containing
the Pumping Frequency. (i.e. Bandwidth = 5 lines of resolution)
9.3.3.2 Excluding the lines of resolution contained in the Pumping Frequency (PF)
Band, the Velocity Amplitude (Inch/sec-Peak) of any line of resolution,
measured at bearing locations (ref. Section 5) in any direction (as defined in
Section 4) shall not exceed the Line-Amplitude Band Limit values specified in
Table 9.3. and graphed in Figure 9.3.1, when determined in accordance with
Section 7.2.1 using the frequency range from 0.3 X Running Speed (pump
RPM) to Fmax = 120,000 CPM (2,000 Hertz)
9.3.3.3 The Velocity Band-Limited Overall Amplitude (Inch/sec - Peak) at bearing

locations (ref. Section 5) in any direction (as defined in Section 4) shall not
exceed the Pumping Frequency Band Limited Overall Amplitude Acceptance
Limit value specified in Table 9.3. and graphed in Figure 9.3.1 when
E-218 February 2000

determined in accordance with Section 7.22 using the frequency range from 0.8
X PF to 1.2 X PF.
9.3.3.4 The Acceleration Band-Limited Overall Amplitude (g's Peak) at bearing

locations (ref. Section 5) in any direction (as defined in Section 4) shall not
exceed the Band-Limited Overall Amplitude Acceptance Limit values
specified in Table 9.3. and graphed in Figure 9.3.2 when determined in
accordance with Section 7.2.2 using the frequency range from 0.3 X Running
Speed to 300,000 CPM.
LINE-AMPLITUDE BAND LIMITS

BAND FREQUENCY VELOCITY
RANGE (CPM) (INCH/SEC - PEAK)
0.3 x RPM
1 0.04
0.8 x RPM
0.8 x RPM
2 0.075
1.2 x RPM
1.2 x RPM
3 0.04
3.5 x RPM
3.5 x RPM
4 0.03
120,000 CPM
BAND-LIMITED OVERALL AMPLITUDE LIMITS

FREQUENCY ACCELERATION
BAND
RANGE (CPM) (g’s PEAK)
1.5g - POSITIVE DISPLACEMENT
1 0.3 x RPM - 300K CPM
1.0g - NON-POSITIVE DISPLACEMENT
PUMPING VELOCITY
FREQUENCY
FREQ. (INCH/SEC - PEAK)
RANGE (CPM)
BAND (PF)
5 Lines of resolution 0.075 PISTON
BAND 5
centered on PF. 0.05 VANE
Table 9.3 Maximum Allowable Vibration Levels For Positive Displacement And Centrifugal
Pumps
February 2000 E-219

POSITIVE DISPLACEMENT & CENTRIFUGAL PUMPS

.10
V .09
.08 .075 .075 PISTON
E
.07 PF BAND
L
O .06
.05 .05 VANE
C .04 .04
I .04
.03 .03
T
Y .02
BAND 1 BAND 2 BAND 3 BAND 5 BAND 4
.01
(IN/SEC) 1 2 3 4 5 6 7 8 9 10 11 Fmax = 120K

cpm
RUNNING SPEED ORDERS
NOTE: BAND 5 IS A FLOATING BAND BANDWIDTH OF THE PUMPING FREQUENCY +- 2 LINES OF RESOLUTION
ACCEPTANCE LIMITS FOR BAND 5 ARE LINE AMPLITUDE VIBRATION LEVELS
Figure 9.3.1 Line Amplitude Acceptance Limits for Positive Displacement & Centrifugal Pumps
POSITIVE DISPLACEMENT & CENTRIFUGAL PUMPS

BAND-LIMITED OVERALL AMPLITUDE ACCEPTANCE LIMITS
A
C BAND 1
2.0
C 1.8
E 1.6
L 1.4 1.5g POSITIVE DISPLACEMENT
E 1.2
R 1.0
A 0.8
T 0.6 1.0g NON-POSITIVE DISPLACEMENT
I 0.4
O 0.2
N
(g’s) Fmax = 300K
FREQUENCY - CPM
Figure 9.3.2 Band-Limited Overall Amplitude Acceptance Limits for Positive Displacement &
Centrifugal Pumps
E-220 February 2000

9.3.4 VERTICAL MOUNTED PUMPS
9.3.4.1 Vertically mounted pump systems with a "Vertical Mount Height" greater than
5 feet will have an allowable increase in Velocity Amplitude Acceptance
Limits in Bands 1, 2, and 3 of 5% per foot of "Vertical Mount Height" greater
than 5 feet. (e.g. A 7 foot Vertical Mount Height would yield a 10% increase
[(7 ft - 5 ft) x 5%/ft] in the Table 9.3. A Velocity Amplitude Acceptance
Limits specified for Bands 1, 2, and 3. Therefore the limit for Band 1 would be
[0.4 Inch/sec + (0.4 Inch/sec x 0.1)] = 0.44 Inch/sec-Peak.
9.3.4.2 Vertical Mount Height is defined as the furthest measurable distance from the
machine mounting to the end of the driver or the end of the pump, which ever
is greater.
February 2000 E-221

SECTION 9.4
VIBRATION STANDARDS
FOR GEARBOXES
9.4.1 Gearboxes shall not exceed the Vibration Limits specified in Figures 9.4.1 and 9.4.2
GEAR BOX
.10
V .09
E .08 .075
L .07
O .06
C .05
.04 .04 .04
I .03 .03 .03
T .03
Y .02
BAND 1 BAND 2 BAND 3 BAND 4 BAND 5 BAND 6
.01
(IN/SEC) 1 2 3 4 5 6 7 8 9 10 11 Fmax = 120K
cpm
RUNNING SPEED
Figure 9.4.1 Line Amplitude Acceptance Limits for Gearboxes
GEAR BOX
BAND LIMITED OVERALL AMPLITUDE ACCEPTANCE LIMITS
A
C 1.0g (Peak)
C 1.0
E 0.9
L 0.8
E 0.7
R 0.6 BAND 1
A 0.5
T 0.4
I 0.3
O 0.2
N 0.1
(g’s) Fmax = 3.5 X GMF
FREQUENCY - or 600K
CPM (Which ever is greater)
Figure 9.4.2 Band-Limited Overall Amplitude Acceptance Limits for Gearboxes
E-222 February 2000

SECTION 9.5
VIBRATION STANDARDS
FOR DEFAULT LIMITS
If Vibration Limit values are not available for the machine being considered, the Specification
Limit shall (unless specified otherwise by the purchaser) default to the following:
9.5.1 NON-MACHINE TOOLS:
Non-machine Tools shall not exceed the Vibration Limits specified in Table 9.5 and
graphically illustrated in figures 9.5.1 and 9.5.2.
VELOCITY LINE-AMPLITUDE BAND LIMITS

BAND FREQUENCY VELOCITY
RANGE (CPM) (INCH/SEC - PEAK)
1 0.3 x RPM 0.04
0.8 x RPM
2 0.8 x RPM 0.075
1.2 x RPM
3 1.2 x RPM 0.04
3.5 x RPM
4 3.5 x RPM 0.03
8.5 x RPM
5 8.5 x RPM 0.03
60,000 CPM
6 60,000 CPM 0.03
120,000 CPM
ACCELERATION BAND-LIMITED OVERALL AMPLITUDE LIMITS

BAND FREQUENCY ACCELERATION
RANGE (CPM) (g’s PEAK)
1 0.3 x RPM - 120K 0.5
Table 9.5 Maximum Allowable Vibration Levels for Non-Machine Tools
February 2000 E-223

NON-MACHINE TOOL LINE AMPLITUDE

ACCEPTANCE LIMITS
.10
V .09
E .08 .075
L .07
O .06
C .05
.04 .04 .04
I .03 .03 .03
T .03
Y .02
BAND 1 BAND 2 BAND 3 BAND 4 BAND 5 BAND 6
.01
(IN/SEC) 1 2 3 4 5 6 7 8 9 10 11 Fmax = 120K

cpm
RUNNING SPEED
Figure 9.5.1 DEFAULT Line Amplitude Acceptance Limits for Non-Machine Tools
NON-MACHINE TOOL BAND-LIMITED OVERALL

A AMPLITUDE ACCEPTANCE LIMITS
C 1.0
C 0.9
E 0.8
L 0.7
E 0.6 0.5g NON-MACHINE TOOL
R 0.5
A 0.4
T 0.3
I 0.2 BAND 1
O 0.1
N
Fmax = 120K
FREQUENCY -
Figure 9.5.2 DEFAULT Band-Limited Overall Amplitude Acceptance

Limits for Non-Machine Tools
E-224 February 2000

GLOSSARY
ACCELERATION: The time rate of change of velocity. Typical units are ft/sec2 and g's (1 g =
32.17 ft/sec2 = 386 in/sec2 = 9.81 meter/sec2). Acceleration measurements are made with
accelerometers.
Note: By international agreement, the value 9.80665 m/s2 = 980,665 cm/s2 =
386.089 in/s2 = 32.174 ft/s2 has been chosen as the standard acceleration due to
gravity (g). ISO 2041 (1990)
ACCELEROMETER: Transducer whose output is directly proportional to acceleration. Most
commonly used are mass loaded piezoelectric crystals to produce an output proportional to
acceleration.
AMPLITUDE: A measure of the severity of vibration. Amplitude is expressed in terms of
peak-to-peak, zero-to-peak (peak), or rms. For pure sine waves only:
• Peak (P) = 1.414 x RMS
• Peak-to-Peak = 2 x Zero-to-Peak (Peak)
ANTI-ALIASING FILTER: A low-pass filter designed to filter out frequencies higher than
1/2 the sample rate in order to prevent aliasing.
ANTI-FRICTION BEARING: See ROLLING ELEMENT BEARING.
AVERAGE: The sum of the values of the measurements taken divided by the number of
measurements taken.
BALANCE: When the mass center line and rotational center line of a rotor are coincident.
BALANCING: A procedure for adjusting the radial mass distribution of a rotor by adding or
removing weight, so that the mass centerline approaches the rotor geometric centerline achieving
less vibration amplitude at rotational speed.
BAND-LIMITED OVERALL AMPLITUDE: For vibration level limits specified in terms of
"BAND-LIMITED OVERALL
AMPLITUDE LIMITS: The total vibration level "A" in a band, as defined by the following
equation, shall not exceed the Overall Amplitude Acceptance Limit specified for the Band
N
∑ A
2
i
A = i=1
W
A = Overall vibration level in the Band
Ai = Amplitude in the ith line of resolution in the Band
(i = 1) = The first line of resolution in the Band
(i=N) = The last line of resolution in the Band
N = The number of lines of resolution in the Band
February 2000 E-225

W = Window Factor (W = 1.5 for a Hanning Window)

BEATS: Periodic variations in the amplitude of an oscillation resulting from the combination of
two oscillations of slightly different frequencies. The beats occur at the difference frequency.
ISO 2041 (1990).
BEAT FREQUENCY: The absolute value of the difference in frequency of two oscillations of
slightly different frequencies. ISO 2041 (1990)
BLADE PASS FREQUENCY (PUMPING FREQUENCY): A potential vibration frequency
on any bladed machine (turbine, axial compressor, fan, pump, etc.). It is represented by the
number of fan blades or pump vanes times shaft rotating frequency.
CALIBRATION: A test to verify the accuracy of measurement instruments. For vibration, a
transducer is subjected to a known motion, usually on a shaker table, and the output readings are
verified or adjusted.
COMPLETE MACHINE: A complete machine is defined as the entire assembly of
components, sub-components, and structure, which is purchased to perform a specific task(s).
On a Complete Machine Assembly with all individual components operating in their normal
operating condition, mode, and sequence, the Component Vibration Level Limits for the
complete machine acceptance are the same as when the component is tested individually.
CRITICAL SPEED: The speed of a rotating system corresponding to a system resonance
frequency.
DECIBEL (dB): A logarithmic representation of amplitude ratio, defined as 20 times the base
ten logarithm of the ratio of the measured amplitude to a reference. dBV readings, for example,
are referenced to 1 volt rms. dB amplitude scales are required to display the full dynamic range
of an F Analyzer.
DISPLACEMENT: The distance traveled by a vibrating object. For purposes of this
document, displacement represents the total distance traveled by a vibrating part or surface from
the maximum position of travel in one direction to the maximum position of travel in the
opposite direction (Peak-to-Peak) and is measured in the unit mil (1 mil = 0.001 inch).
DYNAMIC RANGE: The difference between the highest measurable signal level and the
lowest measurable signal level that is detectable for a given Amplitude Range setting. Dynamic
Range is usually expressed in decibels, typically 60 to 90 dB for modern instruments.
DYNAMIC MASS: To determine if the mass of the transducer is effecting the measurement,
perform the following steps:
a. Make the desired measurement with the accelerometer.
b. Place a mass equivalent to the mass of the accelerometer adjacent to the
measuring accelerometer.
c. Repeat the measurement.
d. Compare data from a. and c.
e. If any differences (i.e. shift in frequencies) between a. and c. exist, then a less
massive transducer should be used in a.
FFT ANALYZER: Vibration analyzer that uses the Fast Fourier Transform to display vibration
frequency components.
E-226 February 2000

FFT (FAST FOURIER TRANSFORM): A calculation procedure which converts a time

domain signal into a frequency domain display.
FIELD BALANCING: The process of balancing a rotor in its own bearings and supporting
structure rather than in a balancing machine.
FFT (FAST FOURIER TRANSFORM): A calculation procedure which produces a
mathematical relationship between the time domain and the frequency domain resulting in
discrete frequency components from the sampled time data.
FLEXIBLE ROTOR: A rotor that deforms significantly at running speed. This term is used
for rotors that operate close to or above their first critical speed. A rotor is considered flexible
when its speed is more than 75% of its lowest natural frequency in bending.
FORCED VIBRATION: The oscillation of a system under the action of a forcing function.
Typically forced vibration occurs at the frequency of the exciting force.
FREE VIBRATION: Vibration of a mechanical system following an initial force -- typically at
one or more natural frequencies.
FREQUENCY: The repetition rate of a periodic event, usually expressed in cycles per second
(Hertz -abr. HZ), cycles per minute (CPM), or multiples of rotational speed (Orders). Orders are
commonly referred to as IX for rotational speed, 2X for twice rotational speed, etc. Frequency is
the reciprocal of the Period.
NOTE: Vibration frequencies are expressed in Hertz (cycle per sec) or CPM (cycle per minute).
Rotational speed (Running Speed) is expressed in RPM (Revolutions per minute).
FREQUENCY DOMAIN: Presentation of a signal whose amplitude is measured on the Y axis,
and the frequency is measured on the X-axis.
FREQUENCY RESOLUTION (∆ ∆ F): ∆ f = (FMAX - FMIN)/# Lines of resolution. ∆f
represents the minimum spacing between data points in the spectrum.
FMAX: Maximum Frequency Limit of the spectrum being evaluated.
FMIN: Minimum Frequency Limit of the spectrum being evaluated.
FREQUENCY RESPONSE: Portion of the frequency spectrum which can be covered within
specified frequency limits.
g: The value of acceleration produced by the force of gravity. (32.17 ft/sec2, 386 in/sec2, 9.81
m/sec2).
GEAR MESH FREQUENCY: A potential vibration frequency on any machine that contains
gears: equal to the number of teeth multiplied by the rotational frequency of the gear.
HANNING WINDOW: A Digital Signal Analysis (DSA) window function that provides better
frequency resolution than the flat top window, but with reduced amplitude
HARMONIC: Frequency component at a frequency that is an integer (whole number e.g. 2X.
3X. 4X, etc.) multiple of the fundamental (reference) frequency.
HI BANDPASS FILTER: A device that separates the components of a signal and allows only
those components above a selected frequency to be amplified.
HERTZ (Hz): The unit of frequency represented by cycles per second.
February 2000 E-227

IMBALANCE: Unequal radial weight distribution of a rotor system; a shaft condition such that
the mass and shaft geometric centerlines do not coincide.
INTEGRATION: A process producing a result that when differentiated, yields the original
quantity. Integration of acceleration, for example, yields velocity. Integration is performed in an
FFT Analyzer by dividing by 2πf where f is the frequency of vibration. Integration is also used
to convert velocity to displacement.)
LARGE APPARATUS AC/DC MOTORS: Reference NEMA Publication No. MG 1, Motors
and Generators, Section III
LARGE MACHINES: Part 20. Induction Machines, Part 21. Synchronous Motors, and Part
23. DC Motors.
LINEAR NON-OVERLAPPING AVERAGE: An averaging process where each Time block
sample used in the averaging process contains data not contained in other Time blocks (i.e. Non-
overlapping) used in the averaging. Linear averaging is performed in the Frequency Domain,
and each sample is weighted equally.
LINES: The total number of data points in a spectrum (e.g. 400, 800, 1600, etc.)
LINE AMPLITUDE LIMIT: The maximum amplitude of any line of resolution contained
within a band shall not exceed the Line Amplitude Acceptance Limit for the Band.
LINE OF RESOLUTION: A single data point from a spectrum which contains vibration
amplitude information. The Line of Resolution amplitude is the Band Overall Amplitude of the
frequencies contained in the ∆f Frequency Resolution.
MEASUREMENT POINT: A location on a machine or component at which vibration
measurements are made.
MICROMETER (MICRON): One millionth (0.000001) of a meter. (1 micron = 1 x 10-6
meters = 0.04 mils.)
MIL: One thousandth (0.001) of an inch. (1 mil = 25.4 microns.)
NATURAL FREQUENCY: The frequency of free vibration of a system when excited with an
impact force. (Bump Test).
ORDER: A unit of frequency unique to rotating machinery where the first order is equal to
rotational speed. See FREQUENCY
BAND LIMITED OVERALL READING: The vibration severity amplitude measured over a
frequency range defined by a FMIN and a FMAX
PEAK: Refers to the maximum of the units being measured, i.e., peak velocity, peak
acceleration, peak displacement.
PEAK-TO-PEAK: Refers to the displacement from one travel extreme to the other travel
extreme. In English units, this is measured in mils (.001 inch) and in metric units it is expressed
in micro-meter µM (.000001 meters).
PERIOD: The amount of time, usually expressed in seconds or minutes, required to complete
one cycle of motion of a vibrating machine or machine part. The reciprocal of the period is the
frequency of vibration.
E-228 February 2000

PHASE (PHASE ANGLE): The relative position, measured in degrees, of a vibrating part at
any instant in time to a fixed point or another vibrating part. The Phase Angle (usually in
degrees) is the angle between the instantaneous position of a vibrating part and the reference
position. It represents the portion of the vibration cycle through which the part has moved
relative to the reference position .
PRECISION SPINDLE: Spindles used in machining processes which require high accuracy,
high speed, or both.
RADIAL MEASUREMENT: Measurements taken perpendicular to the axis of rotation.
RADIAL VIBRATION: Shaft dynamic motion or casing vibration which is in a direction
perpendicular to the shaft centerline.
RESONANCE: The condition of vibration amplitude and phase change response caused by a
corresponding system sensitivity to a particular forcing frequency. A resonance is typically
identified by a substantial amplitude increase and related phase shift.
RIGID ROTOR: A rotor that does not deform significantly at running speed. A rotor whose
parts do not take up motion relative to each other, i.e., all points move in the same direction at
the same instant of time. A rotor is considered rigid when its speed is less than 75% of its lowest
natural frequency in bending.
RMS: (Root mean square) Equal to 0.707 times the peak of a sinusoidal signal.
ROLLING ELEMENT BEARING: Bearing whose low friction qualities derive from rolling
elements (balls or rollers), with little lubrication.
ROTATIONAL SPEED: The number of times an object completes one complete revolution
per unit of time, e.g., 1800 RPM.
SIDE BAND: Equals the frequency of interest plus or minus one times the frequency of the
exciting force.
SIGNATURE (SPECTRUM): Term usually applied to the vibration frequency spectrum
which is distinctive and special to a machine or component, system or subsystem at a specific
point in time, under specific machine operating conditions, etc.
Usually presented as a plot of vibration amplitude (displacement, velocity or acceleration) versus
time or versus frequency. When the amplitude is plotted against time it is usually referred to as
the TIME WAVE FORM.
SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL) HORSEPOWER AC/DC
MOTORS: Reference NEMA Publication No. MG 1, Section II SMALL (FRACTIONAL)
AND MEDIUM (INTEGRAL) MACHINES. Part 12. Tests and Performance - AC and DC
Motors.
TIME DOMAIN: Presentation of a signal whose amplitude is measured on the Y axis and the
time period is measured on the X axis.
TRANSDUCER (PICKUP) -VIBRATION: A device that converts shock or vibratory motion
into an electrical signal that is proportional to a parameter of the vibration measured. Transducer
selection is related to the frequencies of vibration which are important to the analysis of the
specific machine(s) being evaluated/analyzed.
February 2000 E-229

UNBALANCE: See IMBALANCE

VELOCITY: The time rate of change of displacement with respect to some reference position.
For purposes of this document, velocity is measured in the units Inch per second-Peak.
NOTE: THE REFERENCE FOR MANY OF THE DEFINITIONS IN THIS GLOSSARY IS

THE GLOSSARY FROM THE HEWLETT PACKARD PUBLICATION "EFFECTIVE
MACHINERY MEASUREMENTS USING DYNAMIC SIGNAL ANALYZERS,"
APPLICATION NOTE 243-1
E-230 February 2000

Appendix F—PT&I Technologies Correlation Relationships
This appendix contains the correlation relationships between the various PT&I technologies (see paragraph 3.3.1).
Technology Correlation Indication When Used

Ultrasonic Analysis
Trending & Absolute Limit
(36-44 KHz)
These techniques are indicators of minor bearing damage
and/or lubrication starvation and/or contamination. All rely on
Spike Energy Trending &
detection of micro-impacting between the rollers and Not recommended for use on critical equipment.
(25-35 KHz) Absolute Limit
raceway which excites the natural frequency of the bearing
rings. Not as effective
Shock Pulse Trending &
(32 KHz Ctr.. freq.) Absolute Limit
Provides adequate detection of most

Vibration Narrowband
mechanical and electrical faults. Periodic monitoring, establish interval based on
Signature Trending &
Effectiveness related to sensor mounting and analysis absolute level and rate of change, criticality and
Analysis Absolute Limit
techniques. equipment application.
(0-20 Khz)
Trending & Primarily used for supervisory systems, limited

Displacement Shaft position relative to bearing journal.
Absolute Limit machinery diagnostic capability.
Limited applicability. Should be used as

Not recommended except for low
Overall Measurements Limited Trending a pass/fail criteria. Does not support
cost/low risk equipment.
fault analysis.
Trending Transient monitoring, impact detection, and in response

Time Domain Analysis Troubleshooting
Time Coincident to alarms.
Phase is unstable for electrical faults, looseness, oil

whirl/whip, and resonance. Phase is stable for
Phase Analysis Time Coincident Troubleshooting
imbalance and misalignment. Note: Misalignment
typically shows 180 degree phase shift.
Table F–1. Vibration Monitoring Correlation
February 2000 F-231

Initial interval of six months. When discrete frequency

Trending Spectrometric and ferrographic indications of bearing, gear,
Wear Particle Analysis associated with gears or bearings are presents. See oil
Time coincident or seal wear.
analysis section for more details.
High temperature & high vibration level are indicative of

Thermal Analysis Time coincident When vibration levels are above alarm limits.
imminent failure.
Advanced Filtration/ Debris For all lubricated bearings indication that damage to
Trending Confirm bearing damage.
Analysis bearing surfaces has occurred.
Detects electro-mechanical faults such as broken rotor bars,

Motor Current Signature
Time coincident defective shorting rings, air gap eccentricity, non- Supplement vibration monitoring on critical motors.
Analysis
symmetrical magnetic field.
Measures complex phase impedance (resistance and

Motor Circuit Supplement vibration monitoring on critical motors.
Time coincident inductance), resistance and capacitance to g-round, and
Analysis/Evaluation Acceptance testing.
rotor influence on magnetic field (indirectly).
Pressure, temperature, flow, power consumption, cycle

Performance Testing Time coincident Degradation of thermodynamic and operating performance.
time, and operating hours.
Table F–2. Correlation of Vibration Monitoring with Other PT&I Technologies
Wear particle buildup precedes significant vibration in most

Vibration Trending Routinely, when equipment is being operated.
cases.
High temperature often comes with major wear particle

Thermal Analysis Time coincident Confirm bearing degradation.
production just before bearing failure.
Advanced Filtration/ Trending Major bearing damage has occurred when material appears
Routinely, with every filter cleaning or change.
Debris Analysis Time coincident in lubricating system filters.
Table F–3. Correlation of Lubricant & Wear Particle Analysis with Other Technologies
F-232 February 2000

Vibration Time coincident Significant vibration accompanies rising temperatures. On condition of suspected bearing or coupling problem.
Lubrication High temperature often comes with major wear particle

Trending On condition of suspected bearing problem.
Wear Particle Analysis production just before bearing failure.
Advanced Filtration/ After high temperature alerts personnel to damage

Trending Damage creates material residue.
Debris Analysis potential.
Abnormal temperatures coincident with acoustic signals

Leak Detection Time coincident On condition of suspected leak.
indicating internal leak.
Electrical Circuit Testing Time coincident High resistance generating heat. On condition of suspected circuit problem.
Discoloration from overheating due or corrosion/oxidation at

Visual inspection Trending On condition of indicated problem.
connectors.
Table F–4. Correlation of Thermal Analysis with Other Technologies
Filter debris buildup confirms damage causing increased

Vibration analysis Trending Routinely, when equipment is being operated.
vibration.
Debris analyzed and source identified by spectrographic or Routine oil samples show marked increase in level of
Lubricant Analysis Trending
other means. foreign material.
Table F–5. Correlation of Advanced Filtration & Debris Analysis with Other Technologies
February 2000 F-233

Acoustic signals corroborate flow indications of valve

Passive Ultrasonics Time coincident To confirm leakage by isolation valves.
leakage by the seat. Indicator of tube/tubesheet leakage.
High or low temperatures corroborate indications of valve

Thermal Analysis Time coincident Confirm bearing degradation.
leakage by the seat.
Thermal Analysis (Differential Increasing T as flow decreases due to blockage or pump On condition of flow decrease/ T change across heat
Time coincident
temperatures) degradation. exchanger.
Cavitation caused by pump, impeller, or wear ring

Vibration analysis Time coincident deterioration. Line blockage indicated by increased vane On condition of reduced system flow rate.
frequency.
Visual inspection Trending Heat exchanger inspection shows internal fouling. To confirm reduced flow.
Table F–6. Correlation of Flow Measurement with Other Technologies
Moisture induced corrosion and clogging of orifices and Periodically, frequency depending on dew point
Dew Point Monitoring Trending
binding of operators. readings.
Dirt and contaminants clog orifices, restrictors and bind Periodically, frequency depending on contamination
Hydraulic oil testing Trending
valve operators. buildup.
Table F–7. Correlation of Valve Operator Testing with Other Technologies
F-234 February 2000

Distinguish between unbalance, rotor bar or end ring On condition - when routine vibration analysis indicates
Vibration analysis Time coincident (MCSA)
breakage, or high resistance. possible rotor bar or end ring problems.
Trending (Surge On condition - when motor current analysis indicates

Motor Current Analysis Rotor winding defects in slip ring induction motors.
Comparison) potential rotor problem.
Thermal analysis (IRT High temperatures/high resistance in motor control and On condition. Either technology can confirm a finding of
Time coincident (TDR)
imaging) electrical cabling/circuits. the other.
Insulation and connector discoloration, corrosion, pitting and Periodically, when access is available to the busses,
Visual inspection Time coincident
other signs of deterioration caused by heat. cabling and terminal boards.
RF Monitoring Time coincident Arcing in the windings of large generators. Continuous monitoring where RF system installed.
Table F–8. Correlation of Electrical Testing with Other Technologies
Abnormal temperatures coincident with acoustic signals

Thermal analysis Time coincident On condition of suspected leak.
indicating leak.
Visual evidence of damage to valve discs and seats When valve internals are open and available for
Visual inspection Trending
sufficient to cause leakage. inspection.
Flow downstream of shut valve provides acoustic indication

Nonintrusive flow Time coincident On condition of suspected leak.
of leakage by the seat.
Table F–9. Correlation of Ultrasonic/Acoustic Leak Detection with Other Technologies
February 2000 F-235

Nature of specific problem implied by abnormal breakaway

Vibration analysis Trending Start up after major repair or extended shutdown.
or coastdown testing.
Start up after major repair or extended shutdown.

Abnormal vibration during startup. Abnormal vibration during
Vibration analysis Time coincident Before shutdown to conduct investigation of suspected
operation.
problem.
Before shutdown to conduct investigation of a

Thermal analysis Trending Abnormal temperature during operation.
suspected problem.
Lubricant Wear Particle Abnormal wear indicating increased internal friction within Before shutdown to conduct investigation of a
Trending
Analysis machine. suspected problem.
Advance Filtration/Debris Before shutdown to conduct investigation of a

Trending Abnormal condition indicating increased friction.
Analysis suspected problem.
Table F–10. Correlation of Breakaway or Coastdown Testing with Other Technologies
Visual inspection (including Time coincident Physical condition of flask/pressure vessel. Wall thickness On condition of long periods (>10%) of "wet" gas in
fiber optics) Trending reduced. system.
Time coincident Physical condition of flask/pressure vessel. Wall thickness On condition of long periods (>10%) of "wet" gas in
Ultrasonic imaging
Trending reduced. system.
Table F–11. Correlation of Dew Point Measurement with Other Technologies
F-236 February 2000

Trending (Post For each condition where damaged parts are found after
Vibration Analysis Physical condition of parts are deteriorated or worn.
replacement analysis) detection by vibration analysis.
Thermal Analysis Time coincident Visual and infrared images of suspected faults. Visual image taken to accompany each IRT image.
On condition where heat exchanger fouling, not pump

Thermal Analysis Trending Increasing ?T across heat exchanger with operating time.
condition, is suspected cause.
When system inspection reveals buildup of

Lubricant Physical Analysis Trending Conditions created by lengthy operation with lubricant OOS.
contaminants.
Lubricant Wear Particle

Trending Examination of wear particles. For suspected cases of abnormal wear.
Analysis
Internal corrosion of system components (particularly When system internals are open and available for
Dew Point Measurement Trending
HP air). inspection.
Nonintrusive Flow On condition where heat exchanger fouling, not pump

Trending Reduced flow through heat exchanger due to fouling.
Measurement condition, is suspected cause.
Table F–12. Correlation of Visual Inspections with Other Technologies
February 2000 F-237

Identifies location of leak requiring repair. Characteristic

Acoustic Leak Detection Time coincident On condition to confirm and locate leak.
sonic or ultrasonic signature.
Identifies location of leak requiring repair. “Cool” spots

Thermal imaging Time coincident On condition to confirm and locate leak.
indicate condenser leaks.
Lubricant Wear Particle Time coincident

Trace elements exposed by wear. Continuously monitor and confirm particle presence.
Analysis Trending
Table F–13. Correlation of Trace Element Sensing with Other Technologies
Metal fatigue/intergranular stress corrosion cracking Confirms whether or not acoustic emission indications
Acoustic emission Trending
detectable in large metal vessels using ultrasonic imaging. of metal lattice breakdown are valid.
Presence and concentration of trace element nuclides

Trace Element Sensing Time coincident To confirm and measure wall thinning.
indicates erosion/corrosion induced wall thinning.
In Service Stress/Strain, Monitored stress exceeds yield point of monitored To confirm whether actual damage in the form of
Trending
Torque Measurement component. cracking or thinning has occurred.
Condition of objects being inspected for erosion, corrosion, When the item being inspected has a surface subject to
Radiography Trending
cracking or exfoliation. wall thinning or an internal volume subject to cracking.
Table F–14. Correlation of Ultrasonic Imaging with Other Technologies
F-238 February 2000

Metal fatigue/intergranular stress corrosion cracking Confirms whether or not acoustic emission indications
Acoustic Emission Trending
detectable in large metal vessels using ultrasonic imaging. of metal lattice breakdown are valid.
Presence and concentration of trace element nuclides

Trace Element Sensing Time coincident To confirm and measure wall thinning.
indicates erosion/corrosion induced wall thinning.
In Service Stress/Strain, Abnormal strain coincident with indication of a strain-related To confirm whether actual damage in the form of
Trending
Torque Measurement defect. cracking or thinning has occurred.
Condition of objects whose near-surface volume can be Where confirmation of a defect is required before
Ultrasonic imaging Trending
scanned. opening for repair.
Table F–15. Correlation of Radiography with Other Technologies
Relationship between temperature, temperature cycles and When needed to understand the relationships to devise
Thermal Analysis Time coincident
strain. better control measures.
Acoustic Emission (Fatigue Ultrasonic noise produced as a result of existing crack

Time coincident Pressure flasks and tanks.
Monitoring) cleaving. Determining crack location possible.
Table F–16. Correlation of Stress-Strain Measurement with Other Technologies
February 2000 F-239


In conjunction with code requirements for periodic (10
year) inspection or after a rise in acoustic emission
Dynamic Radiography Trending Cracking in heavy metal weld joints.
events in a specific region which may indicate
developing cracks.
To monitor pressure vessel or heavy section weld

In Service Stress/Strain, High levels of strain coincident or distortion evident from
Time coincident deterioration during hydro test or other high stress
Torque Measurement other methods.
event.
In conjunction with code requirements for periodic (10

Ultrasonic Imaging Trending Flaw detection and mapping. year) inspection or after a rise in acoustic emission
events in a specific region.
Table F–17. Correlation of Acoustic Emission with Other Technologies
Lubricant Wear Particle Trending On condition when position indicator shows bearing
Confirmation of bearing wear.
Analysis Time coincident wear.
Thermal analysis Time coincident Confirmation of bearing wear. On condition when position indicator shows wear.
On condition when position indicator shows movement

Vibration analysis Time coincident Confirmation of shaft misalignment.
or wear.
Advanced Filtration/Debris On condition when position indicator shows movement

Trending Confirmation of bearing wear.
Analysis or wear.
Table F–18. Correlation of Ultrasonic, Eddy Current, and Photonic Position Sensors with Other Technologies
F-240 February 2000

Figure F–1 depicts a simplified Chilled Water System and the various components that can be
monitored using the aforementioned correlated PT&I technologies.
Chiller
Fan
Chilled Water Line
Isolation
Valve
Motor Cooling Coil

Operated
Valve
Air
Chilled Water Pump Handling
Unit
Figure F-1. Chilled Water System
For example, a chilled water system would require the following PT&I techniques to be used in
order for the entire system to be evaluated:
a. Flow Rates—Chiller water flow would be measured using precision, non-intrusive flow
detectors.
b. Temperature—Differential temperature would be measured to determine heat transfer

coefficients and to indicate possible fouling of tubes.
c. Pressure—Differential pump and chiller pressures would be measured to determine

pressure drops and pump efficiency.
d. Electrical—Motor power consumption and motor circuit testing would be used to assess
the condition of the motor circuits and to correlate with pump efficiencies.
February 2000 F-241

e. Ultrasonic Thickness—Pipe wall thickness would be measured to determine erosion

and corrosion degradation.
f. Vibration—Vibration monitoring would be used to assess the condition of the rotating

components such as pumps and motors. Additionally, structural problems would be
identified through resonance and model testing.
g. Lubricant Analysis—Oil condition and wear particle analysis would be used to identify
problems with the lubricant and correlated with vibration when wear particle
concentrations exceed pre-established limits.
h. Fiber Optics—Fiber optic inspections would be used in response to indications of

component wear, tube fouling, etc.
i. Thermography—Thermography scans would be used to check motor control centers

and distribution junction boxes for high temperature conditions. Piping insulation
should be checked for porosities.
j. Eddy Current—Eddy current would be used to determine and locate leaking tubes.
k. Airborne Ultrasonics—Airborne ultrasonics would be used to detect leaking air from

control system and compressor leaks.
F-242 February 2000

Appendix G—Alignment Standard19
FORWARD
It is recommended that laser alignment be used on all shaft coupled machines be a part of
implementation of Reliability Centered Maintenance. Laser alignment designed into the
machine will:
• Minimize machine installation and set-up time.
• Allow verification of machine productivity and machine life.
• Allow identification of unique errors in machine motions and structure.
The LASER ALIGNMENT SPECIFICATION FOR NEW AND REBUILT MACHINERY

AND EQUIPMENT provides engineering performance guidelines for use by Plant engineering,
maintenance and design personnel as well as machinery and equipment builders during the
design and building of new equipment and the rebuild of existing equipment.
19
specifications which are included in this document. This document may be copied in whole or in part for the use of
February 2000 G-243

TABLE OF CONTENTS
1.0 PURPOSE
2.0 SCOPE
3.0 COUPLED SHAFTS LASER ALIGNMENT

3.1 SHAFT ALIGNMENT REQUIREMENTS
3.2 COUPLED SHAFTS ALIGNMENT
3.3 LASER SHAFT ALIGNMENT SYSTEM REQUIREMENTS
3.4 SHAFT ALIGNMENT TOLERANCES
3.5 COUPLED SHAFTS ALIGNMENT VERIFICATION
3.6 MACHINE BASES
3.6.1 MACHINE BASE CONSTRUCTION
3.6.2 FOOT CENTERLINES
3.6.3 JOINING SHAPES TOGETHER
3.6.4 REQUIREMENTS FOR MACHINE PADS OR FLATS
3.6.5 MACHINE BASE SUPPORT
3.7 JACKBOLTS
3.8 HOLD-DOWN BOLTS
3.9 PIPING
3.10 SHIMS
3.11 MACHINE VERTICAL MOBILITY
3.12 COUPLING PLAY/BACKLASH
3.13 AXIAL SHAFT PLAY
4.0 ALIGNMENT OF BELT DRIVEN MACHINES

4.1 MOTOR BASES
4.2 RUNOUT
4.3 SHEAVE ALIGNMENT
GLOSSARY
FIGURES AND TABLES
Figure 1 Coupled Shaft Alignment
Table 1 Coupled Shaft Alignment Tolerance Values
Figure 2 Offset and Angular Misalignment
Figure 3a Suggested Base Plate Assemblies
Figure 3b Suggested Base Plate Assemblies (Continued)
G-244 February 2000

1.0 PURPOSE:
The purpose of this specification is to ensure that provisions for laser alignment are
designed into all new and rebuilt machine.
2.0 SCOPE:
This document addresses the use of laser alignment systems for SHAFT ALIGNMENT
3.0 COUPLED SHAFTS LASER ALIGNMENT
3.1 COUPLED SHAFT ALIGNMENT REQUIREMENT
NASA operations require laser alignment on all shaft coupled machines to maximize part
quality and productivity, and to eliminate premature machine failure due to
misalignment.
3.2 COUPLED SHAFTS ALIGNMENT
Coupled shaft alignment is the positioning of two or more machines so that the rotational
centerlines of their shafts are colinear at the coupling center under operating conditions.
Coupling Center
Motor Pump / Fan / Gearbox / Etc.
Figure 1 - Coupled Shafts Alignment
February 2000 G-245

3.3 LASER SHAFT ALIGNMENT SYSTEM REQUIREMENTS
The Laser Alignment System used for Coupled Shafts Alignment shall use either a
combined laser emitter and laser target detector unit or separate units for its laser emitter
and laser target detector.
3.4 SHAFT ALIGNMENT TOLERANCES
3.4.1 All shaft-to-shaft centerline alignments shall be within the tolerances

specified in Table 1 unless more precise tolerances are specified by the
machine manufacturer or by the purchasing engineer for special
applications.
RPM TOLERANCE SPECIFICATION

SOFT FOOT ALL <0.002 inch (0.0508 mm) at each foot
RPM HORIZONTAL & VERTICAL ANGULARITY/GAP

PARALLEL OFFSET Inch/10 inch
(mm/254 mm)
SHORT Coupling Diameter
COUPLINGS
<1000 0.005 in (1.2700 mm) 0.015 in (0.3810 mm)
1200 0.004 in (1.0160 mm) 0.010 in (0.2540 mm)
1800 0.003 in (0.7620 mm) 0.005 in (0.1270 mm)
3600 0.002 in (0.5080 mm) 0.003 in (0.0762 mm)
7200 0.001 in (0.2540 mm) 0.0025 in (0.0635 mm)
HORIZONTAL & VERTICAL

PARALLEL OFFSET
PER INCH (25.4 mm) OF
SPACER LENGTH
COUPLINGS
WITH <1000 0.0020 in (0.0508 mm)
SPACERS 1200 0.0015 in (0.0381 mm)
1800 0.0010 in (0.0254 mm)
3600 0.0005 in (0.0127 mm)
7200 0.0003 in (0.0076 mm)
TABLE 1 COUPLED SHAFT ALIGNMENT TOLERANCE VALUES
JACKSHAFTS: Below “critical speed” of Jackshaft

Short coupling tolerances apply to each coupling of the jackshaft.
G-246 February 2000

Above “critical speed” of Jackshaft

Short coupling tolerances apply relative to the centerlines of the
two machines.
3.4.2 The Tolerances specified in Table 1 are the maximum allowable

deviations from Zero-Zero Specifications or ALIGNMENT TARGET
SPECIFICATIONS (i.e. an intention targeted offset and/or angularity).
3.4.3 Acknowledging that machines often move after start-up due to

THERMAL GROWTH, dynamic load shifts, etc., the alignment
parameters shall be measured and adjusted for operating conditions.
3.5 COUPLED SHAFTS ALIGNMENT VERIFICATION
3.5.1 Laser alignment will be performed at the purchaser’s facility on all shaft
coupled machines during installation of the equipment.
3.5.2 When verifying the alignment of coupled shafts the contractor must
document and provide the following data for each set of coupled shafts:
a. Alignment tolerances used.

b. SOFT FOOT
c. Vertical ANGULARITY (Pitch) at the COUPLING POINT.
(Refer to Figure-2)
d. Vertical OFFSET at the coupling point.
e. Horizontal angularity (Yaw) at the coupling point.
f. Horizontal offset at the coupling point.
3.5.3 This information shall be provided to the purchaser at the time of

functional check out.
3.6 MACHINE BASES
3.6.1 MACHINE BASE CONSTRUCTION
3.6.1.1 A solid and rigid machine base is required to achieve and

maintain shaft alignment.
3.6.1.2 Where bases are constructed using concrete or grouts final shaft
alignment shall not be conducted until ample curing time has
taken place. (A minimum of Thirty days is recommended)
3.6.1.3 Where the machine foundation installation specification does not

require a concrete or grout base or the installation schedule does
not permit the proper cure time for the concrete/grout, refer to
Figures 3a and 3b for suggested alternate machine base
constructions.
February 2000 G-247

3.6.1.4 Where corrosion is or may be a problem the base must be

fabricated of corrosive resistant materials.
3.6.1.5 Where the machine base is constructed from commercially

available steel or castings:
3.6.1.5.1 Use H, M, I, square, tube, and bar shapes with a

minimum 0.5 inch (1.27 cm) thickness.
3.6.1.5.2 For machine bases consisting of a single steel plate,

plate thickness must equal or exceed the thickness of the
machine foot, but be no less than 1.0 inch (2.54 cm).
The plate surface that the driver and driven machines
will bolted to must be machine ground and of sufficient
size to accommodate the machine components, push/pull
blocks and/or jack screws. Jackscrews must not rest on
any rounded edges.
3.6.1.5.3 Use of channel or angle stock is not recommended.

Where use is necessary, the channel or angle stock must
be reinforced using square bar or plate meeting the
preceding thickness requirements.
3.6.1.6 After all welding and machining is completed, stress relieve the
entire base.
3.6.2 FOOT CENTER LINES
The stiffness of the machine base shall be sufficient that no foot centerline
shall deform or deflect more that .001” (.0254 mm) over the operating
range from alignment conditions to full load conditions.
3.6.3 JOINING SHAPES TOGETHER
When joining shapes together they shall conform to the appropriate

applicable A.S.M.E. standard(s) for welding.
3.6.4 REQUIREMENTS FOR MACHINE PADS OR FLATS
3.6.4.1 After all welding and machining has been completed and the
base has been stress relieved, the surface of all pads or flats for
each machine to be installed on the base must be co-planar,
within .001 inch (0.0254 mm). (refer to figures 3a and 3b)
3.6.5 MACHINE BASE SUPPORT
G-248 February 2000

The feet of the driver and driven machines must not overhang the machine
base.
3.7 JACKBOLTS
Jackbolts shall be located at the front and rear feet of the movable machine for
horizontal alignment positioning. (This requirement also applies to vertically
mounted units and vertically mounted flanged units). Jackbolts shall be parallel
to the flat/pad surface and align on the center line formed by the hold down bolts
in the cross machine direction. Ample room shall be left for removal and
insertion of shims used in the vertical alignment of the coupled machines.
3.8 HOLD-DOWN BOLTS
The use of hold down bolts is the preferred method of fastening components to
the base. Hold-down bolts shall meet the following specifications:
a. Hold-down bolts for both the driver and the driven machine(s) (in pairs or
in trains) shall be positioned (spotted) after the machine’s shafts have been
aligned.
b. Hold-down bolts shall be centered in the hole of the machine foot.
c. Hold-down bolts shall be the preferred method of fastening machines to
the base.
d. Hold-down bolts shall not be undercut (“Chicagoed”) to achieve
HORIZONTAL adjustment.
3.9 PIPING
Piping must be fitted, supported, and sufficiently flexible such that soft foot due
to movement caused by tightening pipe flanges doesn’t exceed .002” (.051 mm).
Piping must not restrict the minimum 180 degree rotation requirement of the laser
alignment system.
3.10 SHIMS
Shims shall meet the following specifications:
a. Commercially die-cut.
b. Made of corrosion and crush resistant stainless steel, which is
dimensionally stable when subjected to high compression over long
periods of time.
c. Consistent over the whole shim area, without seams or folds from
bending.
d. Clean, free from burrs, bumps, nicks and dents of any kind.
e. Size numbers or trademarks etched into the shim, not printed or stamped.
February 2000 G-249

f. The smallest commercial shim that will fit around the hold down bolts
without binding shall be used.
g. The overall shim pack shall not exceed a total of three (3) shims.
h. Shims must rest on bare metal, not paint or other coatings.
3.11 MACHINE VERTICAL MOBILITY
All machines shall be installed with a minimum of .125 inch (3.0 mm)
dimensionally stable shims under each surface mounting point for vertical
mobility.
3.12 COUPLING PLAY/BACKLASH
OEM’s must use only the couplings specified by the Government unless
otherwise agreed upon by the purchaser. During the alignment process coupling
play or backlash must be eliminated to accomplish a precision shaft alignment.
3.13 AXIAL SHAFT PLAY
Axial shaft play or end-play must be no greater than .125 inch (3.175 mm).
Accommodation of end movement must be done without inducing abnormal loads
in the connecting equipment.
Horizontal Offset Horizontal Angularity (Yaw)
Motor Pump/Fan/Gearbox/Etc. Motor Pump/Fan/Gearbox/Etc.

Top View Top View
Vertical Offset Vertical Angularity
Motor Pump/Fan/Gearbox/Etc. Motor Pump/Fan/Gearbox/Etc.
Side View Side View
Figure 2 Offset and Angular
G-250 February 2000

The following sketches are provided for

a general guideline and are not
construction drawings. These bases
are intended for situations where the
schedule does permit the proper cure
Machined mounting flats
time for concrete and/or grout.
Machined flats mounting

flats up to 5 “ elevation
Elevation

For attachment to
existing base in
good condition
Machined flats mounting

pads up to 5 “ elevation
Elevation
The sketches are divided into

For attachment to existing applications as noted on the sketches.
base in good condition Bases of this type are generally used on
equipment in the range of 10 hp to 500
hp. Depending upon the speed and
size, between 500 hp and 1000hp it
becomes more cost effective to use the
flanges of I-beams mounted cross-
frame to support the machine instead of
using plate.
Figure 3a Suggested Baseplate Assemblies
February 2000 G-251

Machined flat mounting

flats up to 5 “ elevation
Elevation
For attachment to
existing rough surface
or structure of uncertain
condition
Machined flat mounting

pads up to 5 “ elevation
Elevation
For attachment to existing

rough surface or structure of
uncertain condition
Figure 3b Suggested Baseplate Assemblies
G-252 February 2000

4.0 ALIGNMENT OF BELT DRIVEN MACHINES
4.1 MOTOR BASES
4.1.1 Motors will be provided with adjustable motor bases unless otherwise
specified.
4.1.2 Motors over 5600 watts of power will be provided with adjustable, pivoted
motor bases.
4.1.2.1 Base will have enough adjustment to allow belt replacement

without stretching the new belts.
4.1.2.2 Adjustment method will be by use of two adjusting bolts.
4.2 RUNOUT
4.2.2 After sheaves are installed on the motor and driven shafts, the sheaves will
be checked to ensure that they are true on the shaft.
4.2.3 Runout on the sheaves will be checked with a dial indicator
4.2.4 Sheave runout shall not exceed 0.0580 mm (0.002 in.)
4.3 SHEAVE ALIGNMENT
4.3.2 Unless otherwise specified, drive and driven sheaves will be aligned by
the four-point method.
4.3.3 If the sheave web thickness is not the same on the drive and driven sheave,
shims of the appropriate thickness will be used on the narrower sheave for
the alignment. The thickness of the shims will be recorded and supplied
with the machine information.
February 2000 G-253

GLOSSARY
ACCESSIBLE: The ability to reach and adjust the aligning feature. Consideration should be
given to confined space restrictions, removing guards, bushing plates, hydraulic lines, lubrication
lines, electric lines etc.
ALIGNMENT TARGET SPECIFICATIONS: Desired intentional offset and angularity at
coupling center to compensate for thermal growth and/or dynamic loads. Most properly
specified as an OFFSET, and an angle in two perpendicular planes, horizontal and vertical.
ANGULAR ERROR: A misalignment condition characterized by the angular error between the
desired centerline and the actual centerline. This misalignment condition may exist in planes
both horizontal and vertical to the axis of rotation. (Reference Figure 2)
ANGULARITY: The angle between the rotational centerlines of two shafts. Angularity is a
“slope” expressed in terms of a rise (millimeters or thousandths of an inch) over a run (meter or
inches). (Reference Figure 2).
A.S.M.E.: American Society of Mechanical Engineers
345 East 47th Street
New York, NY 1017
212-705-7722
AXIAL PLAY, AXIAL FLOAT, END FLOAT: Shaft axial movement along its centerline
caused by axial forces, thermal expansion or contraction, and permitted by journal bearings,
sleeve bearings and/or looseness.
BASE PLATE: The surface, often made of steel plate or cast iron, to which the feet of a
machine are attached. (Reference Figure 3a and 3b)
CO-LINEAR: Co-linear means two lines that are positioned as if they were one line. Co-linear
as used in alignment means two or more centerlines of rotation with no offset or angularity
between them. Two or more lines are co-linear when there is no offset or angularity between
them (i.e. they follow the same path).
COPLANAR: The condition of two or more surfaces having all elements in one plane. (per
ANSI Y14.5)
COUPLING POINT: The phrase “COUPLING POINT” in the definition of SHAFT
ALIGNMENT is an acknowledgment that vibration due to misalignment originates at a the point
of power transmission, the coupling. The shafts are being aligned and the coupling center is just
the measuring point.
FULL BEARING FITTING SPACER BLOCK: A single spacer block used for aligning the
machine tool in the vertical plane.
FLATNESS: The condition of a surface having all elements in one plane. (Per ANSI Y 14.5.)
Note: As used in this specifications, a flat is a small surface flush with or cut into a
BASE PLATE, machined flat, and co-planar with the other flats in the base plate. The
flats support the Shims and/or feet of the machine to be installed. A pad is a small block
G-254 February 2000

of metal that serves to elevate the feet of the machine above the surface of the base plate.
Pads are commonly used compensate for differences in machine center line heights, and
for increased corrosion resistance by raising the machine feet out of any possible standing
fluids. Pads and flats have holes drilled and tapped in their centers to accept hold down
bolts.
HORIZONTAL: Parallel to the mounting surface.
JACKBOLTS, JACKSCREWS: Positioning bolts on the machine base which are located at,
each foot of the machine and are used to adjust the position of the machines.
LEVEL: Parallel to a reference plane or a reference line established by a laser.
MACHINE: The total entity made up of individual machine components such as motors,
pumps, spindles, fixtures, etc. Also reference MACHINE COMPONENT.
MACHINE BASE: The structure that supports the machine or machine components under
consideration.
MACHINE COMPONENT: An individual unit such as a motor, pump, spindle, fixture, etc.
often referred to as a machine in its own context.
MACHINE DEPENDENT: A condition that is dependent on the machining operation and the
design requirement of the part being machined.
N.I.S.T. : National Institute of Standards and Technology
Building 304, Room 139
Gaithersburg, MD 20899
301-975-3503
OFFSET: The distance (in thousands of an inch or in millimeters) between the rotational
centerlines of two parallel shafts. (Reference Figure 1).
PITCH: An angular misalignment in the vertical plane. (ANSI/ASME b5.54-1991)
POSITION ERROR (CENTERLINE/OFFSET MISALIGNMENT): A misalignment
condition that exist when the shaft centerline is parallel but not in line with (not coincidental)
with the desired alignment centerline. (Reference Figure 1).
QUALIFYING LEVEL POINTS: Qualified leveling points are locations that have their
heights defined and must be in same plane. That plane must be parallel to the mounting surfaces
of the slide assembly.
REPEATABILITY: The consistency of readings and results between consecutive sets of
measurements.
SHAFT ALIGNMENT: Positioning two or more machines (e.g. a motor driving a hydraulic
pump(s), etc.) so that the rotational centerlines of their shafts are collinear at the coupling center
under operating conditions. (Reference Figure 2)
SOFT FOOT: A condition that exists when the bottom of all of the feet of the machinery
components are not on the same plane (can be compared to a chair with one short leg). Soft foot
is present if the machine frame distorts when a foot bolt is loosened or tightened. It must be
corrected before the machine is actually aligned.
PARALLEL SOFT FOOT: A parallel gap between the machine foot and its support surface.
February 2000 G-255

ANGULAR SOFT FOOT: An angled gap between the machine foot and its support surface.
INDUCED SOFT FOOT: A type of soft foot that is caused by external forces, ( pipe strain,
coupling strain, etc.,) acting on a machine independent of the foot to base plate connection.
“SQUISHY” SOFT FOOT: A type of soft foot characterized by material, (could be Shims,
paint, rust, grease, oil, dirt, etc.) acting, like a spring between the underside of the machine foot
and the base plate contact area.
SPACER BLOCKS: See FULL BEARING FITTING SPACER BLOCK.
STRESS FREE CONDITION: The condition that exists when there are no forces acting on the
structure of a machine, machine component, or machine base that would cause distortion in the
structure such as bending, twist, etc.
THERMAL EFFECTS (GROWTH OR SHRINKAGE): This term is used to describe
displacement of shaft axes due to machinery temperature changes (or dynamic loading effects)
during start-up.
TOLERANCE, DEADBAND, WINDOW, OR ENVELOPE: An area where all misalignment
forces sum to a negligible amount and no further improvement in alignment will reduce
significantly the vibration of the machine or improve efficiency.
TOLERANCE VALUES: Maximum allowable deviation from the desired values, whether
such values are zero or non-zero.
VERTICAL: Perpendicular to the horizontal plane.
YAW MISALIGNMENT: An angular misalignment in the horizontal plane.
G-256 February 2000

Appendix H - Balance Standard20
FORWARD
It is recommended that Balance Certification of all new and rebuilt machinery and equipment be
a part of implementation of Reliability Centered Maintenance. Precision balance and
certification, as a part of machine performance evaluation will:
• Maximize part quality, machine productivity and machine life.
• Minimize machine installation and set-up time.
• Allow verification of machine performance and "health" throughout the machine's life.
The BALANCE STANDARD FOR NEW AND REBUILT MACHINERY AND EQUIPMENT
provides engineering performance guidelines for use by Facilities Operations and Maintenance
as well as machinery and equipment builders during the design, development, and building of
new equipment and the rebuild of existing equipment. The balance quality, specified by the user
and acknowledged by the contractor, establishes a common goal of acceptability by both parties.
Such quality, also enables contractors to provide evidence of the superiority and build integrity
of their product.
20
specifications which, are included in this document. This document may be copied in whole or in part for the use of
February 2000 H-257

TABLE OF CONTENTS
1.0 PURPOSE
2.0 SCOPE

3.1 DEFAULT BALANCE LEVELS
3.2 BALANCE CALCULATIONS
3.3 STANDARD KEY
3.4 BALANCE WEIGHTS
4.0 MACHINE QUOTATION, CERTIFICATION AND ACCEPTANCE

4.1 QUOTATION
4.3 ACCEPTANCE
GLOSSARY
TABLES AND FIGURES
Table 1 Default Balance Specifications
Table 2 Balance Quality Grades for various groups of Representative Rigid Rotors
(ISO 1940/1-1986)
H-258 February 2000

1.0 PURPOSE
The purpose of this standard is to:
• Reduce operating costs by establishing acceptable balance grades for new and
rebuilt rotating machinery and equipment.
• Improve the life and performance of rotating machines and equipment

purchased.
• Provide a uniform procedure for evaluating the balance characteristics of a

machine for certification and acceptance.
2.0 SCOPE
This standard establishes acceptable quality for balance of new and rebuilt rotating
machinery and equipment purchased.
3.0 BALANCE REQUIREMENTS
3.1 DEFAULT BALANCE SPECIFICATION
If no other limit is specified, the vibration criteria listed in Table 1 will be used for
acceptability of the machine in question. The vibration criteria are for the vibration
amplitude at the fundamental rotational frequency or one times running speed (1X).
This is a narrowband limit. An overall value is not acceptable.
Nominal
Shaft Speed Maximum Vibration Maximum Displacement
(RPM) (in/sec, Peak) (mils, Peak-to-Peak)
900 0.02 0.425

1200 0.026 0.425
1800 0.04 0.425
3600 0.04 0.212
Table 1. Default Balance Specifications
3.2 BALANCE CALCULATION
Table 2 provides the ISO1940/1-1986 balance quality grades for various groups of
representative rigid rotors. The RCM Guide contains more detailed information and
the complete ISO 1940/1 –1986 table.
February 2000 H-259

Product of The
Balance
Relationship
Quality Rotor Types—General Examples
(eper x ω)1,2
Grade
mm/s
Crankshaft/drives of rigidly mounted fast diesel engines with six or more
G100 100 cylinders4
Complete engines (gas or diesel) for cars, trucks, and locomotives5
Car wheels, wheel rims, wheel sets, drive shafts

Crankshaft/drives of elastically mounted fast four-cycle engines (gas or
G40 40
diesel) with six or more cylinders
Crankshaft/drives of engines of cars, trucks, and locomotives
Drive shafts (propeller shafts, cardan shafts) with special requirements

Parts of crushing machines
Parts of agricultural machinery
G16 16 Individual components of engines (gas or diesel) for cars, trucks and
locomotives
Crankshaft/drives of engines with six or more cylinders under special
requirements
Parts of process plant machines

Centrifuge drums
Fans
Flywheels
Pump impellers
G6.3 6.3 General machinery parts
Medium and large electric armatures (of electric motors having at least 80
mm shaft height) without special requirements
Small electric armatures, often mass produced, in vibration insensitive
applications and/or with vibration isolating mountings
Individual components of engines under special requirements
Rigid turbo-generator rotors

Turbo-compressors
Medium and large electric armatures with special requirements
G2.5 2.5
Small electric armatures not qualifying for one or both of the conditions
specified for small electric armatures of balance quality grade G6.3
Turbine-driven pumps
Grinding-machines drives
G1 1
Small electric armatures with special requirements
Spindles, disc, and armatures of precision grinders

G0.4 0.4
Gyroscopes
Table 2. Balance Quality Grades for Various Groups of Representative Rigid Rotors (ISO 1940/1-
1986)
H-260 February 2000

3.3 STANDARD KEY
For rotating machines and machine components with a keyed shaft, balancing will
achieved using a standard one-half key in the key seat in accordance with ISO 8821-
1989. If a "full key", corresponding to the half key used for balancing, is not
provided with the rotating machine, a tag, as shown in Figure 1, will be attached to
the machine indicating the dimension of the key used to perform the balance test.
A
A = Key length as used for balancing this rotor
B (usually in the form of a “half depth”
B = Key length as used for balancing the attached

rotor (such as coupling half, pulley, fan, etc.)
This is determined by measuring the attached.
rotors keyway length at its hub.
Final Key Length

(A+B)/2
Figure 1. Balance Test Key Dimension
3.4 BALANCE WEIGHTS:
Permanently attached balancing weighs must be secured by welding, bolting, pop-

riveted, or of a "clip-on" design.
3.4.1 If bolted, a hardened bolt must be used in conjunction with a mechanical

locking device (e.g. lock washer or lock nut).
3.4.2 Clip-on" balancing weights can only be used on centrifugal type fans and
must be located and attached on the ID pitch of the blades such that the
rotational motion of the fan creates a positive seating of the "clip-on"
weight against the fan blade.
3.4.3 Balancing weights and method of attachment must be stable at equipment

operating temperature, and of a material compatible with the parent
material of the fan to which the balancing weight is attached.
NOTE: THE USE OF STICK ON LEAD WEIGHTS IS NOT

ACCEPTABLE.
February 2000 H-261

3.4.4 Any parent metal removed to achieve dynamic or static balance shall be
drilled out in a manner which will maintain the structural integrity of the
rotor or sheave.
3.4.5 Access to any fan rotor for field balancing shall be designed in to the
system.
NOTE: IT IS RECOMMENDED THAT COMPONENTS (ROTOR, SHAFTS,

SHEAVES, ETC.) BE BALANCED INDIVIDUALLY AND THEN TRIM
BALANCED AS A TOTAL ASSEMBLY.
4.0 MACHINE QUOTATION, CERTIFICATION, AND ACCEPTANCE
4.1 QUOTATION
4.1.1 The Quotation shall specify that the equipment will meet the applicable
balance quality of this Specification - or the balance quality (if different
from Specification B1.0 Latest Version) specified by the purchaser in the
"Request for Quote."
4.1.2 The Quotation shall state the applicable specification balance quality
being quoted.
4.1.3 Any additional costs required to meet the specification quality shall be
grouped in a separate section of the Quotation and titled "BALANCE
QUALITY". Costs must be itemized and sufficiently detailed to permit a
complete evaluation by the Purchaser.
4.2.1 Balance measurements shall:
4.2.1.1 Be the responsibility of the supplier unless specified otherwise

by the purchaser.
4.2.1.2 Be performed by technically qualified person who is trained and

experienced in machinery balancing. The technical
qualifications of the person doing the balance certification shall
be submitted as a part of the machine balance certification data.
4.2.1 Be submitted to the maintenance orginization or other authorized

representative before acceptance of the machinery or equipment being
purchased will be authorized.
4.2.3 Balance quality for machine certification shall be measured prior to "run-
off' at the vendor's facility. Where it is impractical to set-up and test a
H-262 February 2000

complete machine at the vendor's facility, arrangements shall be made to

perform the test at the purchaser's facility. Under this circumstance,
shipment of the equipment does not relieve the vendor of the
responsibility for meeting the specified balance quality.
4.2.4 The purchaser shall have the option to verify balance quality of equipment
during machine "run-off' at the vendor's test site prior to shipment - or at
the plant site per Section 4.2.3 - prior to final acceptance authorization.
4.3 ACCEPTANCE
Authorization for machine/equipment acceptance based on the balance quality of this

specification requires signature by the purchaser's authorized representative. A copy
of the acceptance must be sent to the plant's Purchasing department before final
acceptance is authorized.
February 2000 H-263

GLOSSARY
ACCELERATION: The time rate of change of velocity. Typical units are ft/sec2 and g's (1 g =
32.17 ft/sec2 = 386 in/sec2 = 9.81 meter/sec2). Acceleration measurements are made with
accelerometers.
Note: By international agreement, the value 9.80665 m/s2 = 980,665 cm/s2 =
386.089 in/s2 = 32.174 ft/s2 has been chosen as the standard acceleration due to
gravity (g). ISO 2041 (1990)
ACCESSIBLE: The ability to reach and adjust the aligning feature. Consideration should be
given to confined space restrictions, removing guards, bushing plates, hydraulic lines, lubrication
lines, electric lines etc.
AMPLITUDE: A measure of the severity of vibration. Amplitude is expressed in terms of
peak-to-peak, zero-to-peak (peak), or rms. For pure sine waves only:
• Peak (P) = 1.414 x RMS
• Peak-to-Peak = 2 x Zero-to-Peak (Peak)
BALANCE: When the mass centerline and rotational centerline of a rotor are coincident.
BALANCING: A procedure for adjusting the radial mass distribution of a rotor by adding or
removing weight, so that the mass centerline approaches the rotor geometric centerline achieving
less vibration amplitude at rotational speed.
CALIBRATION: A test to verify the accuracy of measurement instruments.
COMPLETE MACHINE: A complete machine is defined as the entire assembly of
components, sub-components, and structure, which is purchased to perform a specific task(s).
On a Complete Machine Assembly with all individual components operating in their normal
operating condition, mode, and sequence, the Component Balance Quality for the complete
machine acceptance are the same as when the component is tested individually.
DISPLACEMENT: The distance traveled by a vibrating object. For purposes of this
document, displacement represents the total distance traveled by a vibrating part or surface from
the maximum position of travel in one direction to the maximum position of travel in the
opposite direction (Peak-to-Peak) and is measured in the unit mil (1 mil = 0.001 inch).
FIELD BALANCING: The process of balancing a rotor in its own bearings and supporting
structure rather than in a balancing machine.
FLEXIBLE ROTOR: A rotor that deforms significantly at running speed. This term is used
for rotors that operate close to or above their first critical speed. A rotor is considered flexible
when its speed is more than 75% of its lowest natural frequency in bending.
FREQUENCY: The repetition rate of a periodic event, usually expressed in cycles per second
(Hertz -abr. HZ), cycles per minute (CPM), or multiples of rotational speed (Orders). Orders are
commonly referred to as IX for rotational speed, 2X for twice rotational speed, etc. Frequency is
the reciprocal of the Period.
H-264 February 2000

NOTE: Vibration frequencies are expressed in Hertz (cycle per sec) or CPM (cycle per
minute). Rotational speed (Running Speed) is expressed in RPM (Revolutions per
minute).
HERTZ (Hz): The unit of frequency represented by cycles per second.
IMBALANCE: Unequal radial weight distribution of a rotor system; a shaft condition such that
the mass and shaft geometric centerlines do not coincide.
LARGE APPARATUS AC/DC MOTORS: Reference NEMA Publication No. MG 1, Motors
and Generators, Section III
LARGE MACHINES: Part 20. Induction Machines, Part 21. Synchronous Motors, and Part
23. DC Motors.
LEVEL: Parallel to a reference plane or a reference line established by a laser.
MACHINE: The total entity made up of individual machine components such as motors,
pumps, spindles, fixtures, etc. Also reference MACHINE COMPONENT.
MACHINE COMPONENT: An individual unit such as a motor, pump, spindle, fixture, etc.
often referred to as a machine in its own context.
MICROMETER (MICRON): One millionth (0.000001) of a meter. (1 micron = 1 x 10-6
meters = 0.04 mils.)
MIL: One thousandth (0.001) of an inch. (1 mil = 25.4 microns.)
N.I.S.T. : National Institute of Standards and Technology
Building 304, Room 139
Gaithersburg, MD 20899
301-975-3503
ORDER: A unit of frequency unique to rotating machinery where the first order is equal to
rotational speed. See FREQUENCY
PEAK: Refers to the maximum of the units being measured, i.e., peak velocity, peak
acceleration, peak displacement.
PEAK-TO-PEAK: Refers to the displacement from one travel extreme to the other travel
extreme. In English units, this is measured in mils (.001 inch) and in metric units it is expressed
in micro-meter µM (.000001 meters).
RIGID ROTOR: A rotor that does not deform significantly at running speed. A rotor whose
parts do not take up motion relative to each other, i.e., all points move in the same direction at
the same instant of time. A rotor is considered rigid when its speed is less than 75% of its lowest
natural frequency in bending.
RMS: (Root mean square) Equal to 0.707 times the peak of a sinusoidal signal.
ROTATIONAL SPEED: The number of times an object completes one complete revolution
per unit of time, e.g., 1800 RPM.
SMALL (FRACTIONAL) AND MEDIUM (INTEGRAL) HORSEPOWER AC/DC
MOTORS: Reference NEMA Publication No. MG 1, Section II SMALL (FRACTIONAL)
February 2000 H-265

AND MEDIUM (INTEGRAL) MACHINES. Part 12. Tests and Performance - AC and DC
Motors.
TOLERANCE VALUES: Maximum allowable deviation from the desired values, whether
such values are zero or non-zero.
UNBALANCE: See IMBALANCE
VELOCITY: The time rate of change of displacement with respect to some reference position.
For purposes of this document, velocity is measured in the units Inch per second-Peak.
H-266 February 2000

Appendix I  AC Motor Repair and Reconditioning
1.0 SCOPE
This specification together with the Data Sheets covers the Repair and Reconditioning of AC
Induction Motors. The purpose of this specification is to establish the minimum standards and
documentation recommended for the repair and refurbishment of 3-phase AC Motors.
2.0 STANDARDS AND CODES
These specifications are in addition to the industry accepted practices as stated in the following
Standards and Codes:
IEEE 1068-1990 Recommended Practice for the Repair and Rewinding of Motors
for the Petroleum and Chemical Industry
IEEE 43-1974 Recommended Practice for Testing Insulation Resistance of
Rotating Machinery
IEEE 95-1977 Recommended Practice for Insulation Testing of Large AC
Rotating Machinery with High Direct Voltage
NEMA MG 1-1987 Motors and Generators
ISO 1940 Unbalance Tolerance Guide for Rigid Rotors
ISO 3945-1977 Mechanical Vibration of Large Rotating Machines with Speed
range from 10-200 rev/s-Measurement and Evaluation of
Vibration Severity in Situ
EASA Standards for the Repair of Electrical Apparatus, February 1992
SKF Engineering Data Handbook dated December 1980
2.1 All repairs to Explosion-Proof, Dust Ignition-Proof, or other severe duty motors will
not compromise their original UL Certification.
3.0 GENERAL- ALL ELECTRICAL APPARATUS
3.1 Incoming Inspection: Each machine shall have all nameplate information, all
hardware (i.e., coupling, hub, lifting eyes, etc.), and general condition noted. In
addition, note any damaged or broken parts and, if possible, the primary cause of
failure. The endbells shall be matchmarked.
Visually inspect the stator windings for damage, tightness, cracked insulation, and the
general condition of the motor leads. Report all damage.
3.2 Cleaning: All windings and parts must be cleaned free from dirt, grit, grease, and
oil. Cleaning agents shall be completely removed by steam cleaning then, dried by
baking at a maximum temperature of 3000F. Winding temperature shall not exceed
1760F during the drying process.
February 2000 I-267

3.3 Stripping: Defective windings will be removed in such a manner that no mechanical
damage is done to the laminations or frame. Winding burnout shall be done in a
temperature controlled environment to ensure the stator iron temperature does not
exceed 6500F.
3.4 Insulation System: All insulation and components which make up the insulation
system shall be rated NEMA Class F. All varnishes and coatings shall be compatible
with the insulation. Vacuum pressure impregnation (VPI) is the preferred method of
varnish application.
3.5 Motor Leads: The motor leads shall have a temperature and insulation rating equal
to or greater than the temperature and insulation rating of the insulation system.
Leads on totally enclosed fan cooled (TEFC) and explosion-proof apparatus shall be
properly sealed to meet the original classification of the motor.
3.6 Exterior Finish: The apparatus shall be externally cleaned, sandblasted, and
refinished with primer and a good quality enamel paint. Each repaired motor shall be
labeled with a metal tag which states the name of the repair company and the date of
repair.
3.7 Shipment: Block the shaft to prevent axial travel. Cover the motor with plastic to
protect from weather during shipment. For motors shipped without sufficient
lubricant for industrial operation, attach a red tag labelled "Lubrication Required" to
each fill point.
Return completed "Motor Data Sheet" with the motor.
4.0 SHAFTS
4.1 Inspection: Shafts shall be checked for unusual wear, scoring, and straightness. On
motors greater than 100 HP, a dye penetrant inspection of the shaft is required.
4.2 Bearing Journals and Shaft Extensions: The bearing journals and shaft extension
shall be concentric with the shaft center, smooth polished, and of proper size and fit.
A minimum of two readings using a dial indicator per shaft are required. The
tolerance for total indicated runout (TIR) regardless of shaft size or motor horsepower
are:
4.3 Axial End Play: Total end play in sleeve bearing motors shall be approximately
1/16" per inch diameter of the shaft journal. For rolling element bearings, if
minimum end play tolerances are not provided on motor drawings a value of 0.003
inch should be used.
I-268 February 2000

Maximum Motor Speed (RPM) Maximum TIR (inches)
900 0.002
1200 0.002
1800 0.0015
3600 0.001
Table I – 1.Maximum Total Indicated Runout
4.4 Balancing: All motors greater than 5 HP shall be balanced as close to operating
speed as possible to ISO 1940 G-2.5 using one of the following:
a) All keyways completely filled with half keys; or,

b) With sheaves, coupling hubs, etc. filled with keys.
The balance report shall be included with the motor and include the following: Initial
and final imbalance, location and weight used, length of key stock used, and rotor
weight.
5.0 BEARINGS
All bearings are to be replaced unless otherwise specified. Replacement of the bearings
with a brand or model other than originally installed must be approved by the
Government.
The shaft bearings shall be grease lubricated, anti-friction bearings with minimum L-10
life rating of 40,000 hours in accordance with the Anti-Friction Bearing Manufactures'
Association (AFBMA) method in determining expected bearing life. Bearings must be
able to withstand the loads due to dead weight, unbalance and thrust of rotor assembly.
Bearings shall be rated for 24 hour per day continuous duty service.
5.1 Ball and Roller Bearings: Ball and roller bearings shall be free from defects or
contamination. As a minimum, Annular Bearing Engineers' Committee (ABEC) and
Roller Bearing Engineers' Committee (RBEC) Tolerance 1 bearings shall be used
unless otherwise specified.
For high speed motors (>1800 RPM) , a bearing with an internal clearance of C3 shall
be used.
February 2000 I-269

5.1.1 Removal and Installation: Antifriction bearings shall be removed using

hydraulic or screw-driven bearing pulling equipment. Removal by
hammering is not acceptable.
Bearing condition and fretting patterns shall be noted.
Antifriction bearings shall be installed using an oil bath or induction heater.

Bearings shall not be heated to greater than 2300F.
5.2 Sleeve Bearings: Sleeve bearings are to be checked for cracks or babbitt disbonding
by performing a dye penetrant test.
5.2.1 Installation: Sleeve bearings shall be fitted to the journals using a nondrying
bluing compound. A minimum of 80% contact between the babbitt and the
shaft journal is required. Vendor to specify the method for determining
clearance.
5.3 Lubricants: Lubricant will be specified by the Government. Where sealed or

shielded bearings are used, the grease fittings shall be removed and noted on the
motor data sheet. For motors shipped without sufficient lubricant for industrial
operation, attach a red tag labeled "Lubrication Required" to each fill point.
6.0 ELECTRICAL TEST AND INSPECTION
6.1 Inspection: Visual inspect the rotor for iron damage, rub marks, and overheating of
the rotor bars. Magnetically inspect or Growler test the bars for cracks.
6.2 Electrical Testing: Perform the following electrical tests:
6.2.1 Insulation Resistance: Apply the following test voltage for one (1) minute:
Rated Motor Voltage Test Voltage
200-600 1000
2400-4800 2500
Table I – 2. Insulation Resistance Test Voltages
The minimum acceptable insulation resistance, corrected to 400C, between the

connected leads and the stator is:
Minimum Acceptable = 1M + (Motor Rated Voltage in kV X 1M)
6.2.2 Polarization Index (PI): Perform a ten (10) minute polarization index test on
the motor by applying a DC voltage equal to the motor nameplate voltage and
I-270 February 2000

recording the readings at one(1) and ten (10) minutes. A minimum PI value
of 2.0 must be obtained before performing any overvoltage test.
6.2.3 Overvoltage Testing: DO NOT PERFORM ANY OVERVOLTAGE

TEST OF THE MOTOR IF UNSATISFACTORY RESULTS ARE
OBTAINED FROM THE INSULATION RESISTANCE OR
POLARIZATION INDEX TESTS. If PI<2.0 contact the Government for
additional instructions.
6.2.4 High DC Potential and Comparative Surge Test: Perform the tests at the
following voltages (2X Rated Voltage +1000V):
Rated Motor Voltage Highpot VDC Surge VDC

(nominal) (10%) (10%)
460 2000 2000
2300 5600 5600
4000 9000 9000
Table I – 3. Surge and High Potential Voltages
Record leakage current and any indications of turn-to-turn insulation

breakdown.
6.2.5 Phase Imbalance Tests: The three phases of the motor shall be checked for
proper impedance balance by conducting a no-load test and recording the
voltage and current of all three phases. A maximum current imbalance of
4% is allowed and shall be calculated as follows:
I high - I avg
% Imbalance = X 100
I avg
( + + )
Where : I avg = I 1 I 2 I 3
3
6.2.6 Electrically insulated bearings shall be tested using a megohmmeter with an

output of <50V. The minimum resistance reading is 50 M.
February 2000 I-271

6.3 Vibration Tests: Vibration data shall be acquired at each bearing location radial to
the shaft in the vertical and horizontal planes. In addition, readings shall be taken
axial to the shaft at both ends of the motor. The following guidelines and criteria
apply to all vibration readings:
6.3.1 Vibration Analyzer: The contractor shall use the type of instrumentation and
sensors specified. For example, for a 3,600 RPM machine an accelerometer
with a sensitivity of 100 mV/g and a resonant frequency of at least 15,000 Hz
is required.
A rare earth super magnet and a sound disc shall be used in conjunction with
any vibration data collector which has the following characteristics:
(1) A minimum of 400 lines of resolution.

(2) A dynamic range greater than 70 dB.
(3) A frequency response range of 5Hz-10kHz (300-600,000 cpm).
(4) The capability to perform ensemble averaging.
(5) The use of a hanning window.
(6) Autoranging.
6.3.2 Vibration Data: The vendor shall provide the Government narrowband (400-
line) spectral vibration data for all motors as follows:
(1) For machines operating at or below 1,800 RPM, the frequency

spectrum provided shall be in the range of 5 to 2,500 Hz.
(2) For machines operating greater than 1,800 RPM, the frequency
spectrum provided shall be in the range of 5 to 5,000 Hz.
(3) Two narrowband spectra for each point shall be obtained in the
following manner:
(a) For all machines regardless of operating speed, a 5 to 500

Hz spectrum with 400 lines of resolution shall be used to
analyze balance, alignment, and electrical line frequency
faults.
(b) An additional spectrum of 5 to 2,500 or 5 to 5,000 Hz shall
be acquired for machines operating at or below 1800 RPM
or greater than 1,800 RPM, respectively. This higher
frequency range allows early detection of rolling element
bearing, gear rotor and stator problems.
(c) Vibration data shall be reported in velocity (inches/second

or mm/sec).
(d) The motor shall meet the following applicable vibration

criteria:
I-272 February 2000

Motor Speed Special Application Standard Application

(RPM)
(in/sec, (mm/sec, (in/sec, (mm/sec,
Peak) Peak) Peak) Peak)
900 0.02 0.5 0.08 2.0

1200 0.026 0.66 0.08 2.0
1800 0.04 1.0 0.08 2.0
3600 0.04 1.0 0.08 2.0
Table I – 4. Motor Balance Specifications
(4) Additional Vibration Criteria. All final testing shall be conducted

at normal operating speed under full load conditions.
Frequency (X RPM) Maximum Maximum

Motor Component Amplitude Amplitude
(in/sec Peak) (mm/sec Peak)
Overall 0.10 2.5
0.4 - 0.5 Not detectable
1X See Motor Balance Specifications
2X 0.02 0.5
Harmonics (NX) Not detectable
Roller Element Bearings Not detectable
Side Bands Not detectable
Rotor Bar/Stator Slot Not detectable
Line Frequency (60 Hz) Not detectable
2X Line Frequency (120 Hz) 0.02 0.5
Table I – 5. Motor Vibration Criteria
February 2000 I-273

I-274 February 2000

Appendix J—Maintenance Procedures
This appendix provides NASA Maintenance Procedure Templates (called MPTs for short). The
MPTs have been developed to provide a sample source of time/cycle based maintenance actions,
test procedures and information. A section at the end of the MPT, identified as Engineers Notes,
provides technical information that may be useful when developing site-specific procedures.
The MPTs are based upon sample procedures provided by several NASA Centers, private
industry, and others. The objective of the MPT is to provide instructions without becoming
overly detailed. Simple steps, that provide little value for the typical work force, have not been
included. In some high-risk industry, like nuclear power, maintenance procedures are extremely
detailed and often do not allow even minor deviation when accomplishing. That is not the basis
for the NASA MPTs. The procedures were originally developed in a spreadsheet format and
were provided to the NASA Centers for use in developing site specific procedures.
The Maintenance Procedure Template
The procedure layout is such that all actions are taken in sequence. A person performing the
procedure should arrive at the work site with all necessary tools and materials (including
reference material).
The MPT headings are as follows:
Procedure Number - The number is assigned for use in indexing the procedure. It is expected
that NASA Centers will change this number if the procedure is incorporated into the site-specific
CMMS.
System Description - This section is text that describes the machine/equipment application.
Procedure Description - Text that describes the procedure purpose. The body of the procedure
is often divided into sub-sections. Each sub-section has a heading and that heading is duplicated
in the Procedure Description. This ensures that the entire scope of work is well understood.
Related Tasks - Identifies other tasks that should be performed. Usually tasks with a shorter
periodicity. For example, an annual procedure will identify any semi-annual, quarterly, or
monthly procedures to ensure that all work is done during a single visit to the work site.
Periodicity - Describes how often the procedure is scheduled. NASA Centers will want to
modify the periodicity code to fit the site. Codes used in the MPTs are:
D = Daily W = Weekly M = Monthly Q = Quarterly S = Semi-Annually A = Annually
Multiples of the above are sometimes used and are identified by a number followed by a letter.
For example, 5A indicates that the procedure is scheduled every 5 years.
February 2000 J-275

Labor (Hrs) - This information will usually be two numbers. First is number of people, second
is estimated time for each person. For example: 2-people/2 hrs each. The time estimate is to
perform the task. Because each site is different, no time was estimated to get to the job site.
Special Tools - Identifies tools and test equipment that the technician will need at the job site.
Common tools are not usually identified.
Materials - All materials that will be needed at the job site are listed in this section.
Reference Data - Identifies information, such as a test procedure, that the technician will need in
order to perform the task. This section does not identify reference data that may have been used
to develop the procedure. Only that reference data needed to perform the task is listed in this
section.
Warning Summary - A warning is identified in the procedure anytime there is the potential for
injury (including toxic release to the environment). This section lists every warning that is part
of the procedure. If a warning is used many times in the procedure, it is only listed once in this
section.
Caution Summary - Similar to warning summary. A caution is identified in the procedure

anytime there is the potential for damage to the equipment or damage to collateral equipment.
Note - Although not listed in a summary block, the procedure may also contain a Note. A note
provides relevant information to the person performing the procedure.
Preliminary - The first part of the procedure is identified as the preliminary section. This
section includes all steps taken before going to the job site, or if at the job site, before starting
work on the specified machine. Although there is not a maximum number of preliminary steps,
this section is usually less than 10 steps.
Procedure - The start of the procedure is clearly identified by the title “Procedure.” The first
step in the procedure is labeled “A” and is a phrase that identifies the work to be accomplished.
The next step is labeled “A1” and is an action item. Each subsequent action step is numbered in
ascending order, “A2, A3, ...” If the procedure can be broken into discrete sections, there maybe
a “B” , “C”, etc.
Inspection Data - If data is to be collected, there will usually be an Inspection Data section. The
procedure will identify the data and direct where it is to recorded in the Inspection Data section
or other location. The Inspection Data section is always located at the end of the Procedure
section.
A section at the end of the MPT is identified as Engineers Notes. The Engineers Notes provides
background information that may be useful when developing site-specific procedures. It is not
part of the procedure in that it is not intended to be provided (printed out) for use in the field or
entered into the site CMMS. The Engineers Notes are a tool for use in developing site-specific
procedures.
J-276 February 2000

Table J-1: Sample Procedures
Procedure numbers, listed below, refer to sample procedures in this appendix.
Procedure Machine/System Procedure Summary

Number
PT&I-0001 Rotating Machinery Vibration Data Collection
PT&I-0002 Various Qualitative Infrared Thermography
Inspection
PT&I-0003 Motor Test Insulation
PT&I-0004 Transformer Test Insulation
PT&I-0005 Circuit Breaker Test Insulation
PT&I-0006 Oil Filled Transformer Sample and Test Transformer Oil
PT&I-0007 Transformer Power Factor Test
PT&I-0008 Electrical Distribution Power Factor Test
PT&I-0009 Bushing Power Factor Test
E-0001 Transformer Inspect and Clean Transformer
E-0002 Battery Bank Battery Impedance Test
E-0003 Uninterruptible Power Supply Inspect and Test UPS
E-0004 Electrical Distribution Inspect and Clean Electrical Panels
E-0005 High/Med Volt Circuit Breaker Inspect and Test Circuit Breaker
M-0001 Air Handler Inspect and Clean
M-0002 Chiller Inspect and Clean
February 2000 J-277

Table J-2 is a sample procedure lay out with a combination of

description and sample text.
Table J-2
Block Title Text

Procedure Number PT&I-0003 - This procedure number is assigned by the centers for use in
a CMMS and for indexing purposes. The objective of the procedure is
to provide instructions without becoming overly detailed.
System Description Motor - Text that describes the machine/equipment application.
Procedure 1. Test Insulation - Text to describe what the procedure does. The body
Description of the procedure is often divided into sub-sections.
2. Next Procedure - Each sub-section has a heading and that heading is
duplicated in the Procedure Description. This ensures that the entire
scope of work is well understood.
Related Tasks E-0009 - Identifies other tasks that should be performed concurrent with
this task. Usually tasks with a shorter periodicity. This is an aid to
ensuring effective use of time.
Periodicity A - Code that describes how often the procedure is scheduled. Codes
are assigned by Center work control and are used by the CMMS.
Sample codes are: D = Daily, W = Weekly, M = Monthly, Q =
Quarterly, S = Semi-Annually, A = Annually, 5A = every 5 years.
Labor (Hrs) 0.5 - Estimate of number of people, and time for each person, to perform
task. If number of people is not specified, assume one person.
Special Tools Direct Current Insulation Resistance Tester (Megohmmeter, Megger),
Thermometer - Identifies special tools and test equipment that will be
needed at the job site. Common tools, that the technician normally
would carry, are not usually identified.
Materials Oil Filter, Air Filter, Belt - All replacement parts and materials that will
be needed at the job site are listed in this section. The CMMS usually
contains detailed part numbers for these items.
Reference Data OEM Manual, Other Standard, NASA Procedure - Identifies
information, such as a test procedure, that the field technician will need
in order to perform the task.
Warning Summary 1. Test to ensure all circuits are de-energized. - A warning is identified
in the procedure anytime there is the potential for injury (including toxic
release to the environment). This section lists every warning that is part
of the procedure.
2. Circuit may have dangerous voltage potential following testing. - If
the same warning is used many times in the procedure, it is only listed
once in this section. If there is more than one warning, they are
numbered in this section.
J-278 February 2000

Caution Summary Protect semi-conductor control devices from potential high voltage. -
Similar to warning summary. A caution is identified in the procedure
anytime there is the potential for damage to the equipment or damage to
collateral equipment.
Reserved This section was reserved for future use by the Centers.
Preliminary This section includes all steps taken before going to the job site, or if at
the job site, before starting work on the specified machine.
1 Charge batteries and backup batteries. - This section is usually less than
10 steps.
2 Ensure equipment/component identification (name and/or number) is
legible and securely affixed to equipment. Repair as required.
Procedure The start of the procedure is clearly identified by the title “Procedure.”
A Test Insulation - The first step in the procedure is labeled “A” and is a
phrase that identifies the work to be accomplished.
A1 De-energize equipment and tag out in accordance with site safety
practices. - The next step is labeled “A1” and is an action item.
A2 Open motor control panels or doors to gain access to circuit to be tested.
- Each subsequent action step is numbered in ascending order, “A2, A3,
...”
A3 Perform next step. - Each step begins with an action verb such as Open,
Inspect, Test, Perform, etc. This keeps the procedure focused.
WARNING Test to ensure all circuits are de-energized. - A warning, if needed,
comes just before the step where potential for injury exists.
A4 Place thermometer in close ...
CAUTION Protect semi-conductor control devices from potential high voltage. - A
caution, if needed, comes just before the step where potential for
equipment damage exists.
A5 Attach ground cable (black cable) from tester to ground.
Note 1 A note can be inserted anywhere in the procedure. If there is more than
one Note, they are numbered. The note is information or direction for
the technician in the field.
Note 2 The note is not an action step. The note is used to clarify an action step
or to offer a decision. Avoid using the note to state why the action is
being taken.
A6 Test to ensure a ground established. - Keep the step as short and clear as
possible. Modifiers (such as "the") are not needed. Simple directions,
that provide little value for the typical work force, need not be included.
Note 3 In some high-risk industry, like nuclear power, maintenance procedures
are extremely detailed and often do not allow even minor deviation
when accomplishing. That is not the basis for the typical industry
procedure.
A7 Attach test cable (usually red cable) to circuit to be tested.
A8 Energize tester.
A9 Record test results at one minute intervals for 10 minutes. - Anytime
data is needed, the procedure states "Record...". A section for Inspection
February 2000 J-279

Data needs to be part of the procedure OR other data collection means

identified.
A9 De-energize tester.
WARNING Circuit may have dangerous voltage potential following testing.
A10 Discharge circuit.
B Next Procedure - New procedure sub-section. This heading is
duplicated in the Procedure Description.
B1 Remove test cables.
B2 Remove thermometer, record temperature.
B3 Close access doors and panels.
B4 Return motor to service.
B5 Repeat steps A1 through A10 for next motor. - Repeat steps or reference
to other procedures can be used. Figures can also be used.
Note 4 The procedure layout is such that all actions are taken in sequence. A
person performing the procedure should arrive at the work site with all
necessary tools and materials (including reference material).
Inspection Data If data is to be collected, there will usually be an Inspection Data

section. The Inspection Data section is always located at the of the
Procedure section.
ID-1 Insulation Resistance at 1 min (Megohm) - Identify the units for data
collection.
ID-2 Insulation Resistance at 2 min (Megohm)
ID-11 Temperature (degree C or F)
Engineer's Notes The Engineers Notes provides background information that may be
useful when developing site-specific procedures.
This section is not part of the procedure. It is not intended to be
provided (printed out) for use in the field or entered into the site CMMS.
J-280 February 2000

Table J-3: Sample Procedure PT&I-0001, Vibration Data Collection
Block Title Text

Procedure Number PT&I-0001
System Description
Procedure Vibration Data Collection
Description
Related Tasks
Periodicity Q
Labor (Hrs)
Special Tools Vibration Data Collector with magnet mounted accelerometer.
Materials
Reference Data
Warning Summary Exercise caution when working around rotating machinery.
Caution Summary
Reserved
Preliminary
1 Charge batteries and backup batteries.
2 Download vibration collection route data from host computer.
3 Test operation of vibration data collector and accelerometer.
Procedure
A Vibration Data Collection
WARNING Exercise caution when working around rotating machinery.
A1 Notify operators or other local occupant before collecting vibration data.
A2 Record machine operating condition (usually directly into the data
collector).
A3 Place magnet mounted accelerometer on installed machine sound disk.
Ensure sound disk is clean and dry. Roll magnet onto the sound disk to
avoid damage and overload to the accelerometer
Note If sound disk is missing, take data directly on machine surface. Ensure
surface is clean and dry. Scrape any paint or glue off surface. Replace
sound disk at next opportunity.
A4 Collect vibration data. If needed, adjust data collector and take
additional data.
A5 Note any unsatisfactory conditions (machine or area) and report them to
supervisor.
A6 Repeat procedure for remaining positions on machine.
A7 Repeat procedure for remaining machines on schedule (route).
A8 Upload vibration data to host computer.
February 2000 J-281

Inspection Data
Engineer's Notes
EN1 For time estimating purposes, allow one minute per data point.
Approximately 10 to 12 minutes for a typical 4 bearing machine.
Triaxial accelerometers will require less time to collect data.
EN2 Periodicity can be adjusted after a baseline is established.
J-282 February 2000

Table J-4: Sample Procedure PT&I-0002, Vibration Data Collection
Block Title Text

System Description
Procedure Qualitative Infrared Thermography Inspection
Description
Related Tasks
Periodicity A
Labor (Hrs) 2 People
Special Tools Infrared Camera, Spare Batteries, Notepad
Materials
Reference Data
Warning Summary 1. Exercise caution when working around rotating machinery.
2. Maintain minimum safe distance from energized electrical circuits.
3. Observe standard safety precautions when working on elevated
structures or roofs.
Caution Summary
Reserved
Preliminary
1 Charge batteries and backup batteries for infrared camera.
2 Prepare image storage devices such as computer disks or PCMICA
cards.
3 Inspect imaging system cables and test camera operation. Verify correct
date/time (if available) has been set in camera.
4 Notify operators or other local occupant before starting inspection.
5 Ensure electrical circuits to be inspected are opened and energized to
minimum 40% of full load current.
Procedure
A Qualitative Infrared Thermography Inspection
WARNING Exercise caution when working around rotating machinery.
WARNING Maintain minimum safe distance from energized electrical circuits.
WARNING Observe standard safety precautions when working on elevated
structures or roofs.
A1 Adjust camera settings such as distance to object and emissivity.
A2 Perform thermographic inspection looking for hot and cold spots,
relative differences in temperature, and temperature deviations from the
normal or expected range.
A3 Save image of items of interest. Ensure camera is adjusted to show
entire temperature range (no "white" or "black" areas in the image).
A4 Note machine, location, and operating or environmental conditions for
each image saved and (if any) immediate actions taken to correct fault.
February 2000 J-283

A5 Repeat procedure for remaining machines/areas on schedule.

A6 Notify operators or other local occupant when inspection is complete.
Note Immediately notify supervisor of any temperature difference (delta-T)
greater than 40C (70F).
A7 Upload infrared images to host computer for analysis and reporting (if
required). Provide notes for analyst use.
Engineer's Notes
EN1 Detailed information regarding safety guidelines is contained in OSHA
Regulations Part 1910.
EN1a See standard 1910.333 for electrical safety including closest approach
distances for energized circuits.
J-284 February 2000

Table J-5: Sample Procedure PT&I-0003, Insulation Test, Motor
Block Title Text

System Description Motor
Procedure Test Insulation
Description
Related Tasks
Periodicity A
Labor (Hrs) 0.5
Thermometer
Materials
Reference Data
Warning Summary 1. Test to ensure all circuits are de-energized. 2. Circuit may have
dangerous voltage potential following testing.
Caution Summary Protect semi-conductor control devices from potential high voltage.
Reserved
Preliminary
Procedure
A Test Insulation
practices.
A2 Open motor control panels or doors to gain access to circuit to be tested.
WARNING Test to ensure all circuits are de-energized.
A3 Place thermometer in close proximity to circuit to be tested.
CAUTION Protect semi-conductor control devices from potential high voltage.
A5 Test to ensure a ground established.
A6 Attach test cable (usually red cable) to circuit to be tested.
A7 Energize tester.
A8 Record test results at one minute intervals for 10 minutes.
A11 Remove test cables.
A12 Remove thermometer, record temperature.
A13 Close access doors and panels.
A14 Return motor to service.
February 2000 J-285

Inspection Data
Engineer's Notes
EN1 Specify the Insulation Resistance test voltage as follows:
EN1a Circuit 480V or less, test voltage 500V
EN1b Circuit 600V, test voltage 1000V
EN1c Circuit 2400V, test voltage 2500V
EN1d Circuit 4160V and above, test voltage 5000v
EN2 Technical standards are updated by the sponsoring organization (such as
ASTM and IEEE). Often the update year is part of the standard number.
Check with the sponsoring organization for the current version of the
standard.
EN2a See IEEE Standard 43-1974, IEEE Recommended Practice for Testing
Insulation Resistance of Rotating Machinery, for guidance on insulation
condition and interpretation of polarization index test results.
J-286 February 2000

Table J-6: Sample Procedure PT&I-0004, Insulation Test, Transformer
Block Title Text

System Description Transformer
Description
Related Tasks
Periodicity 1 to 3 yr
Labor (Hrs) 2 people/1hr ea
Thermometer, 2-Shorting Cables (copper wire or braid)
Materials
Reference Data
Caution Summary
Reserved
Preliminary
Procedure
A Test Insulation
practices.
A2 Open transformer panels or doors to gain access to primary and
secondary winding bushings.
A3 Place thermometer in close proximity to transformer bushings.
A4 Perform three point ground test. Record test results.
Note Three point ground test is performed to verify transformer ground. Do
not continue with this procedure if ground test is unsatisfactory.
A5 Disconnect all lighting arresters, current transformers, and bus or cable
connections. Disconnect primary switch.
A8 Tie (short circuit) the primary bushings together using copper wire or
braid.
A9 Tie (short circuit) the secondary bushings together using copper wire or
braid.
A10 Attach test cable (usually red cable) to primary bushing.
A11 Energize tester.
February 2000 J-287

A12 Record test results at one minute intervals for 10 minutes.

A15 Move test cable to secondary bushing.
A16 Repeat steps A11 through A14.
A17 Move test cable back to primary bushing.
A18 Move ground cable to secondary bushing.
A19 Repeat steps A11 through A14.
A20 Attach ground cable (black cable) from tester to primary switch ground.
A22 Move test cable to primary switch, load side, A-phase.
A23 Energize tester.
A24 Record test results at one minute.
A27 Repeat steps A21 through A25 for B- and C-phase.
A28 Remove test and shorting cables.
A30 Perform related tasks, if any.
A31 Reconnect all lighting arresters, current transformers, and bus or cable
connections. Reconnect primary switch.
A33 Return transformer to service.
Inspection Data
ID-1 Ground Test (ohms)
ID-2 Primary to Ground Insulation Resistance at 1 min (Megohm)
ID-12 Secondary to Ground Insulation Resistance at 1 min (Megohm)
J-288 February 2000


ID-22 Primary to Secondary Insulation Resistance at 1 min (Megohm)
ID-32 Primary Switch, Phase-A to Ground Insulation Resistance at 1 min
(Megohm)
ID-33 Primary Switch, Phase-B to Ground Insulation Resistance at 1 min
(Megohm)
ID-34 Primary Switch, Phase-C to Ground Insulation Resistance at 1 min
(Megohm)
Engineer's Notes
Check with the sponsoring organization for the current standard.
EN1a ANSI/IEEE Standard C57.12.90-1993; IEEE Standard Test Code for
Liquid-Immersed Distribution, Power, and Regulating Transformers.
EN1b ANSI/IEEE Standard C57.12.91-1979 (updated 1995); IEEE Test Code
for Dry-Type Distribution and Power Transformers .
EN3 The Polarization Index (PI) is the 10 minute insulation resistance
reading divided by the 1 minute insulation resistance reading. This
value should be monitored and trended to help determine the condition
of the windings. Guidelines are from S.D.Myers.
EN3a For liquid filled transformers: PI greater than 2.0 is good, 1.25 to 2.0 is
fair, 1.1 to 1.25 is poor, and less than 1.1 is bad.
EN3b For dry transformers the PI will normally be between 1.0 and 1.25.
Insulation resistance value should be greater than 10,000 megohms.
February 2000 J-289

EN4 Procedure is written for a step-down transformer and assumes the high
voltage side is the line side. For step-up transformer, reverse the test
procedure to test the load side first.
EN4a If the line side of the primary switch is also de-energized, you can
modify this procedure to test the line and load sides of the primary
switch. Prior to step A22 close the primary switch and then take
insulation data. Add Warning to test the circuit.
EN5 Time estimate is based upon transformer already de-energized. Add
additional 2 to 3 hours to de-energize and tag out.
J-290 February 2000

Table J-7: Sample Procedure PT&I-0005, Insulation Test, Circuit Breaker
Block Title Text

System Description Circuit Breaker
Description
Related Tasks
Thermometer, Shorting Cable (copper wire or braid)
Materials
Reference Data
Caution Summary
Reserved
Preliminary
Procedure
A Test Insulation
practices.
A2 Open circuit breaker panels or doors to gain access to line side and load
side bushings.
A3 Place thermometer in close proximity to circuit breaker mechanism.
A6 Tie (short circuit) the A-phase line and load bushings together using
copper wire or braid.
A7 Attach test cable (usually red cable) to A-phase bushing.
A8 Energize tester.
A9 Record test results at one minute.
A12 Repeat steps A6 through A11 for the B-phase.
A13 Repeat steps A6 through A11 for the C-phase.
February 2000 J-291


A14 Remove test and shorting cables.
A18 Return circuit breaker to service.
Inspection Data
ID-1 Phase-A to Ground Insulation Resistance at 1 min (Megohm)
ID-2 Phase-B to Ground Insulation Resistance at 1 min (Megohm)
ID-3 Phase-C to Ground Insulation Resistance at 1 min (Megohm)
Engineer's Notes
standard.
EN2a ANSI/IEEE Standard C37.50-1989; American National Standard for
Switchgear-Low Voltage AC Power Circuit Breakers Used in
Enclosures - Test Procedures .
EN2b ANSI/IEEE Standard C37.09-1979; IEEE Standard Test Procedures for
AC High-Voltage Breakers Rated on a Symmetrical Current Basis.
J-292 February 2000

Table J-8: Sample Procedure PT&I-0006, Oil Filled Transformer Tests
Block Title Text

System Description Oil Filled Transformer
Procedure 1. Sample Transformer Oil
Description
2. Perform Field Oil Tests
Related Tasks PT&I-0007
Periodicity A
Labor (Hrs) 2 people/2hrs ea
Special Tools 50cc Glass Syringe, two 16 ounce glass oil sample bottles, Power Factor
Test Set, Acidity Test Kit, Oil Dielectric Test Set, Oil Color Chart
Materials
Reference Data ASTM Standard Test Methods (STM)
D-3613-92 - Sampling Electrical Insulating Oils for Gas Analysis and
Determination of Water Content
D-877-87 - Dielectric Breakdown Voltage of Insulating Liquids Using
Disk Electrodes (Dielectric Withstand Test)
D-1534-90 - Approximate Acidity in Electrical Insulating Liquids by
Color-Indicator Titration
D-1524-84 - Visual Examination of Used Electrical Insulating Oil of
Petroleum Origin In the Field
Power Factor Test Set Operating Instructions
Warning Summary Prior to obtaining oil sample verify transformer is not PCB filled or PCB
contaminated. PCB oil goes by many trade names including Inerteen,
Pyranol, and Askarel. Contact maintenance engineer if oil type is not
known.
Caution Summary
Reserved
Preliminary
2 Record unsatisfactory conditions observed on work order and report
them to supervisor.
Procedure
A Sample Transformer Oil
WARNING Prior to obtaining oil sample verify transformer is not PCB filled or PCB
known.
February 2000 J-293

A1 Collect dissolved gas oil sample from transformer. Use 50cc glass
syringe and follow procedure in ASTM standard D-3613-92.
A2 Collect two additional oil samples in sample bottles. Record equipment
number, date, and oil temperature on one bottle.
B Perform Field Oil Tests
B1 Use oil in un-labeled bottle for steps B2 through B5.
B2 Perform Dielectric Withstand Test (ASTM D-877-87).
B3 Perform Field Acidity Test (ASTM D-1534-90).
B4 Perform Visual Examination (ASTM D-1524-84).
Note See Power Factor Test Set operating instructions for Oil Power Factor
test procedure.
B5 Perform Oil Power Factor.
B6 Record test results in the Inspection Data Section, item ID-1 to ID-4.
B7 Deliver oil sample in labeled bottle to supervisor or PT&I for analysis.
Inspection Data
ID-1 Dielectric Withstand Test (kV)
ID-2 Field Acidity Test (mg KOH/ml)
ID-3 Visual Examination (color scale)
ID-4 Oil Power Factor (percent)
Engineer's Notes
standard.
EN2 Send oil sample in the labeled bottle to test lab for a Karl Fischer
(ASTM D-1533-88), Acid Number (ASTM D-974-87), and Interfacial
Tension (ASTM D- 971-82) test.
EN3 Send 50cc syringe to test lab for gas-in-oil analysis (ASTM D-3613-92)
EN4 Field oil test results shall be as follows:
EN4a Dielectric Test: >30kV
EN4b Acidity Test: <.05 mg KOH/ml
EN4c Visual Examination: <4.0
EN4d Power Factor: <2.0%
EN5 Generate work order if tests fall outside minimum parameters
J-294 February 2000

Table J-9: Sample Procedure PT&I-0007, Transformer Power Factor Test
Block Title Text

Procedure Power Factor Test
Description
Related Tasks PT&I-0004, PT&I-0006, E-0003
Periodicity 3 to 5 yr.
Power Factor Test Set, psychrometer (or temperature/humidity meter),
2-Shorting Cables (copper wire or braid)
Materials
Reference Data Power Factor Test Set Operating Instructions
Warning Summary 1. Test to ensure all circuits are de-energized. 2. Energized electrical
circuits. Observe test device safety precautions. 3. Circuit may have
Caution Summary Ensure shorting cables are removed from primary and secondary
bushings.
Reserved
Preliminary
1 Review prior maintenance test data including thermal image and
ultrasonic noise test results (if available).
3 Record as-found conditions in Inspection Data section; Item ID-1 to ID-
10.
4 For any step in procedure, record unsatisfactory conditions on work
order and report them to supervisor.
Procedure
A Power Factor Test
practices.
A2 Open transformer panels or doors to gain access to primary and
secondary winding bushings.
A3 Perform three point ground test. Record test results.
Note 1 Three point ground test is performed to verify transformer ground. Do
not continue with this procedure if ground test is unsatisfactory.
connections.
February 2000 J-295

A5 Tie (short circuit) the primary bushings together using copper wire or
braid.
A6 Tie (short circuit) the secondary bushings, including neutral, together
using copper wire or braid.
Note 2 If transformer has on-load tap changer, mark the as found position. Test
can not be performed with the on-load tap changer in the neutral
position. Leave no-load tap changer, if installed, in normal operating
position.
A7 Move on-load tap changer (if installed) to minus 1 from neutral position.
A8 Connect test set high voltage lead to primary bushing.
A9 Connect test set return lead to secondary bushing.
A10 Connect test ground to transformer ground.
Note 2 For each test performed, record results in Inspection Data section.
WARNING Energized electrical circuits. Observe test device safety precautions.
A11 Perform primary-to-secondary test with ground circuit guarded.
A12 Perform primary-to-secondary test with secondary circuit guarded.
A13 Perform primary-to-secondary test with secondary and ground circuit
included.
A15 Connect test set high voltage lead to secondary bushing.
A16 Connect test set return lead to primary bushing.
A17 Perform secondary-to-primary test with ground circuit guarded.
A18 Perform secondary-to-primary test with ground circuit included.
A20 Remove shorting cables from primary and secondary bushings.
A21 Move on-load tap changer (if installed) to neutral.
Note 3 If transformer has no-load tap changer, leave in normal operating
position.
A22 Connect test set high voltage lead to primary bushing 1 (usually
identified as H1).
A23 Connect test set return lead to primary bushing 2 (usually identified as
H2).
A24 Perform excitation test H1 to H2.
identified as H2).
H3).
J-296 February 2000


identified as H3).
H1).
A34 Remove all test cables.
connections.
A36 Return tap changer to original position.
CAUTION Ensure shorting cables are removed from primary and secondary
bushings.
A39 Return transformer to service.
Inspection Data Fill in all applicable.

ID-1 Wet Bulb Temperature (C)
ID-2 Dry Bulb Temperature (C)
ID-3 Relative Humidity (%)
ID-4 Weather Conditions (Cloudy, etc.)
ID-5 Oil Level
ID-6 Oil Temperature (C)
ID-7 Maximum Oil Temperature (C)
ID-8 Winding Temperature (C)
ID-9 Maximum Winding Temperature (C)
ID-10 Tank Pressure (psi)
ID-11 Ground Test (ohms)
ID-12 Power Factor, primary-to-secondary, ground circuit guarded.
ID-13 Power Factor, primary-to-secondary, secondary circuit guarded.
ID-14 Power Factor, primary-to-secondary, secondary and ground circuit
included.
ID-15 Power Factor, secondary-to-primary, ground circuit guarded.
ID-16 Power Factor, secondary-to-primary, ground circuit included.
ID-17 Power Factor Excitation, H1-H2
Engineer's Notes
EN1 Specify the Power Factor test voltage as follows:
February 2000 J-297

EN1a Circuit less than 2400V, test voltage 500V

EN1b Circuit 2400V to 4160V, test voltage 2500V
EN1c Circuit 4160V to 10,000V, test voltage 5000V
EN1d Circuit 10,000V and above, test voltage 10,000V
EN2 Time estimate is based upon transformer already de-energized. Add
additional 2 to 3 hours to de-energize and tag out.
EN3 A Power Factor test measures the watts loss and the phase angle
between the current and voltage in the equipment under test. From this
information a determination can be made as to the integrity of the
insulation.
EN3a The Power Factor test is NOT a go-no/go test. Comparisons of past
readings are necessary to determine the insulation condition
EN3b All test values must be temperature corrected to 20C.
EN3c Liquid filled (Oil, Silicone): less than 2% change indicates good
condition; 2% to 4% change, investigate; over 4% change, bad
condition.
EN3d Dry windings: less than 5% change indicates good condition; 5% to 8%
change, investigate; over 8% change, dry out transformer and retest.
EN4 The excitation test is the amount of current required to magnetize the
iron and produce a voltage on the secondary.
EN4a This current value is different for every transformer, dependent on the
amount of iron in the winding core, purity of the iron/silicone
laminations, and amount of copper/aluminum in the windings.
EN4b Consequently there is not an absolute value/limit that is applicable; the
% change from the transformer baseline is the monitored condition.
EN4c Excitation: Any two phases approximately the same, third phase 20%
less than the other two. A change of 10% from previous test needs to be
investigated.
J-298 February 2000

Table J-10: Sample Procedure PT&I-0008, Electrical Distribution Test
Block Title Text

System Description Electrical Distribution
Procedure 1. Switchgear and Phase Bus Power Factor Test
Description
2. Circuit Breaker Power Factor Test
3. Restore to Service
Labor (Hrs)
Special Tools Power Factor Test Set, psychrometer (or temperature/humidity meter),
Shorting Cable (copper wire or braid), Thermometer
Materials
4. Closed circuit breaker has high spring pressure. Keep clear of all
moving parts.
Caution Summary Ensure shorting cables are removed from circuit breaker bushings.
Reserved
Preliminary
4.
Procedure
A Switchgear and Phase Bus Power Factor Test
practices.
A2 Open switchgear panels or doors.
connections.
A4 Place thermometer in close proximity to switchgear or phase bus.
A5 Rack out all circuit breakers and open all switches.
A6 Remove or disconnect all potential transformers.
February 2000 J-299

A7 Connect test set ground to switchgear or phase bus ground.

A8 Connect test set high voltage lead to A-phase bus.
A9 Perform A-phase test and record results.
A11 Repeat steps A7 through A9 for B-phase.
A12 Repeat steps A7 through A9 for C-phase.
B Circuit Breaker Power Factor Test
B1 Open circuit breaker.
B2 Rack out circuit breaker or otherwise disconnect from phase leads or
phase bus.
B3 Place thermometer in close proximity to circuit breaker mechanism.
B4 Connect test set ground to circuit breaker ground.
Note Circuit breaker bushings number 1 through 3 are line side A-phase
through C-phase respectively. Bushings 4 through 6 are load side A-
phase through C-phase respectively.
B5 Connect test set high voltage lead to circuit breaker bushing 1.
B6 Perform circuit breaker power factor test and record results.
B7 Discharge circuit.
B8 Repeat steps B4 through B6 for circuit breaker bushing 2.
WARNING Closed circuit breaker has high spring pressure. Keep clear of all
moving parts.
B13 Close circuit breaker.
B14 Tie (short circuit) the A-phase line and load bushings together using
copper wire or braid.
B15 Connect test set high voltage lead to circuit breaker bushing 1.
B16 Perform circuit breaker power factor test and record results.
B18 Remove shorting cable from A-phase bushings.
B19 Repeat steps B13 through B17 for B-phase bushings.
B20 Repeat steps B13 through B17 for C-phase bushings.
J-300 February 2000

B22 Open the circuit breaker.

B23 Rack in circuit breaker or reconnect phase leads or phase bus.
B24 Repeat procedure for remaining circuit breakers.
C Restore to Service
C1 Remove all test cables.
C2 Reconnect all lighting arresters, current transformers, and bus or cable
connections.
C3 Perform related tasks, if any.
C4 Close circuit breakers and switches as required.
CAUTION Ensure shorting cables are removed from circuit breaker bushings.
C5 Return distribution system to service.

ID-5 Power Factor Switchgear or Phase Bus, A-phase, ground specimen test.
ID-6 Power Factor Switchgear or Phase Bus, B-phase, ground specimen test.
ID-7 Power Factor Switchgear or Phase Bus, C-phase, ground specimen test.
ID-9 Power Factor Circuit Breaker, Bushing 1, ground specimen test.
ID-15 Power Factor Circuit Breaker, A-phase, ground specimen test.
ID-16 Power Factor Circuit Breaker, B-phase, ground specimen test.
ID-17 Power Factor Circuit Breaker, C-phase, ground specimen test.
Engineer's Notes
insulation.
February 2000 J-301

EN2b Attention systems engineer. All test values must be temperature

corrected to 20C.
EN2c For the switchgear and phase bus, power factor should be less than 2%.
High readings indicate excess moisture or loose connections. Loose
connections can be verified using infrared thermograph on an energized
circuit.
EN2d For the circuit breakers, bushings test is for the individual bushing while
the phase test is for the bushing and the lift rods and contacts. Each
phase and bushing should be within 5% of each other.
EN2e Individual bushings should be less than 5% after cleaning. Large 115kV
and 230kV breakers with oil filled bushings will have the Power Factor
baselines etched on the bushing base.
J-302 February 2000

Table J-11: Sample Procedure PT&I-0009, Oil Filled Bushing Power Factor Test
Block Title Text

System Description Oil Filled Bushing
Procedure 1. Power Factor Test Hot Collar Method
Description
2. Power Factor Test Capacitance Tap Method
Related Tasks PT&I-0005, PT&I-0008
Special Tools Power Factor Test Set, psychrometer (or temperature/humidity meter),
Thermometer, Culenite Bushing Cleaner
Materials
Caution Summary
Reserved
Preliminary
4.
Procedure
A Power Factor Test Hot Collar Method
practices.
A2 Gain access to bushing.
connections.
A4 Clean bushing.
Note Do not use any alcohol based cleaning product.
A5 Place thermometer on bushing.
A6 Place power factor test hot collar strap under uppermost bushing
petticoat or rainshield.
A7 Connect test set high voltage lead to hot collar strap.
February 2000 J-303

A8 Ground bushing terminal.

A9 Perform grounded specimen power factor test and record results.
A13 Repeat steps A2 through A12 for other bushings.
connections.
A16 Return system to service.
B Power Factor Test Capacitance Tap Method
B1 De-energize equipment and tag out in accordance with site safety
practices.
B2 Gain access to bushing.
B3 Disconnect all lighting arresters, current transformers, and bus or cable
connections.
B4 Clean bushing.
Note Do not use any alcohol based cleaning product.
B5 Place thermometer on bushing.
B6 Remove capacitance tap cover (at base of bushing).
B7 Connect test set return lead to capacitance tap.
B8 Connect test set high voltage lead to bushing terminal.
B9 Perform grounded specimen power factor test and record results.
B12 Remove all test cables.
B13 Repeat steps A2 through A12 for other bushings.
B14 Reconnect all lighting arresters, current transformers, and bus or cable
connections.
B15 Perform related tasks, if any.
B16 Return system to service.

ID-5 Power Factor Bushing, ground circuit guarded.
J-304 February 2000

Engineer's Notes
insulation.
EN2b All test values must be temperature corrected to 20C.
EN2c Individual bushings should be less than 5% after cleaning. Large 115kV
and 230kV oil filled bushings will have the Power Factor baselines
etched on the bushing base.
EN3 Time estimate is based upon testing only. Allow an additional hour
(each person) to clean bushings.
February 2000 J-305

Table J-12: Transformer
Block Title Text

Procedure Number E-0001
Procedure Inspect and Clean Transformer
Description
Related Tasks PT&I-0004, PT&I-0006, PT&I-0007, PT&I-0008
Special Tools Vacuum Cleaner
Materials Corrosion Inhibitor, Culenite Bushing Cleaner
Reference Data
Warning Summary 1. Test to ensure all circuits are de-energized. 2. If PCB or PCB
contaminated oil has leaked from the transformer, stop work, and notify
maintenance engineer.
Caution Summary
Reserved
Preliminary
Procedure
A Inspect and Clean Transformer
practices.
A2 Open transformer panels or doors to gain access to components and
install safety grounds.
Note1 Procedure is for both liquid filled and dry type transformers.
Components identified for inspection in this procedure are not
necessarily on all transformers.
Note 2 Some older oil filled transformers may be PCB filled or PCB
known.
WARNING If PCB or PCB contaminated oil has leaked from the transformer, stop
work, and notify maintenance engineer.
A3 Inspect transformer and disconnect device (where applicable) for signs
of excessive heating and/or insulation damage.
J-306 February 2000

A4 Inspect all exposed conduit and potheads for secure mounting,

corrosion, damaged fittings, and signs of moisture contamination.
A5 Inspect tank, cooling accessories, seals, valves, gauges, fittings, fans,
fuses, and other external parts and accessories for corrosion, leaks,
looseness, and damage.
A6 Inspect desiccant and desiccant lines (on conservator units) for looseness
and corrosion. Replace desiccant if more than 50% has changed color
from blue to clear.
A7 Inspect nitrogen system (on blanketed units) for corrosion, looseness,
and leaks.
A8 Inspect all exposed ground connections. Ensure connections are clean
and tight. Treat with corrosion inhibitor.
A9 Clean transformer primary and secondary bushings (if accessible).
Clean disconnect switch bushings and insulators (where applicable).
Examine bushings for cracks, chips, or corona flashover.
A10 Clean transformer windings (if possible), enclosure, and panels with
vacuum cleaner.
A11 Ensure heaters (if installed) are working correctly.
A12 Make minor repair. Contact supervisor if repairs are not possible. Note
on work order.
A13 Perform spot cleaning and touchup painting as required.
A15 Remove safety grounds.
A16 Close access doors.
A17 Re-energize transformer and return to service.
A18 Remove debris from work-site.
Engineer's Notes
EN1 In order make effective use of time, this procedure for cleaning and
inspecting a transformer should be used in conjunction with other
procedures (identified in Related Task section) for testing transformers.
EN2b ANSI/IEEE Standard C57.12.91-1979 (updated 1995); IEEE Test Code
for Dry-Type Distribution and Power Transformers .
February 2000 J-307

Table J-13: Battery Bank
Block Title Text

System Description Battery Bank
Procedure Battery Impedance Test
Description
Periodicity S
Special Tools Battery Impedance Test Set
Materials Scotchbrite or very fine emery cloth.
Reference Data Manufacture's/equipment output specification.
Warning Summary Observe standard safety precautions when working on energized
electrical circuits.
Caution Summary
Reserved
Preliminary
Procedure
A Battery Impedance Test
WARNING Observe standard safety precautions when working on energized
electrical circuits.
A1 Connect battery impedance test set AC signal leads to positive (+) and
negative (-) terminals of battery bank.
A2 Clamp impedance receiver unit around positive AC signal lead.
A3 Measure impedance of first cell. Record impedance reading on note
paper or in battery book.
A4 Measure impedance of first strap. Record impedance reading on note
paper or in battery book.
A5 Repeat steps A3 and A4 for each cell/strap combination in battery bank.
A6 Inspect batteries and battery connections for leaks, overheating, or
corrosion.
on work order.
A8 Perform spot cleaning and touchup painting as required.
A9 Record battery voltage and trickle charge rate.
J-308 February 2000


ID-1 Battery impedance test results (use separate sheet or record in battery
book).
ID-2 Record battery voltage and trickle charge in standby mode.
Engineer's Notes
EN1a IEEE Standard 446-1995, "IEEE Recommended Practice for Emergency
and Standby Power Systems for Industrial and Commercial
Applications", IEEE Orange Book.
EN2 Battery impedance tests.
EN2a Battery cell impedance shall be within 10% of each other and within
10% from last test.
EN2b Battery strap impedance shall be less than 0.1 ohm. Readings above 0.1
ohm require cleaning and retorque.
EN-3 Battery voltage and trickle charge in standby to be within 5% of
manufacturer's specifications.
February 2000 J-309

Table J-14: Uninterruptible Power Supply
Block Title Text

System Description Uninterruptible Power Supply
Procedure 1. Battery Impedance Test
Description
2. Inspect and Repair
3. Restore to Service
Related Tasks E-0002
Periodicity S
Special Tools Relay Timing Test Set.
Materials Scotchbrite or very fine emery cloth.
Reference Data Manufacture's/equipment output specification.
Warning Summary Test to ensure all circuits are de-energized.
Caution Summary
Reserved
Preliminary
4 Perform Battery Impedance Test (E-0002)
Procedure
A Inspect and Repair
A1 Disconnect UPS from load.
practices.
A3 Open cabinet.
A4 Inspect casing for overheating, corrosion, or damage.
A5 Inspect printed circuit boards for overheating, cracks, or looseness.
A6 Inspect contactor/transfer switch contacts. Clean with scotchbrite or
very fine emery cloth as required.
A7 Inspect batteries and battery connections for leaks, overheating, or
corrosion.
on work order.
A9 Clean air intakes. Clean or replace air filters.
J-310 February 2000

A10 Test undervoltage relay. Relay should operate at 90% (+ or - 2.5%) of

rated voltage. Calibrate if needed.
A11 Test meters. Meters should operate within + or - 2.5% of scale.
Calibrate if needed.
Note Reference the UPS manufacturer technical manual for step A10.
A12 Test all circuit breakers. Recalibrate trip and close settings as required.
B Restore to Service
B1 Perform spot cleaning and touchup painting as required.
B2 Reconnect unit to load.
B3 Re-energize unit.
B4 Perform operational test of unit. Simulate power failure and check for
proper switching, verify proper voltage and frequency under load.
B5 Return unit to standby mode.
B6 Record battery voltage and trickle charge rate.
B7 Remove debris from work-site.

ID-1 Record undervoltage relay as left pick-up.
ID-2 Record as found and as left meter readings.
ID-3 Record load test parameters.
ID-4 Record battery voltage and trickle charge in standby mode.
Engineer's Notes
EN1a IEEE Standard 446-1995, "IEEE Recommended Practice for Emergency
and Standby Power Systems for Industrial and Commercial
Applications", IEEE Orange Book.
EN2 UPS should engage at less than 90% system voltage, + or - 2.5%.
EN3 Operational Parameters (for yearly reference)
EN-3a Voltage shall be within -5% to +5%
EN-3b Frequency shall be within -0.5% to +0.5%
EN-3c Output current shall be within -5% to +5% of rated current
EN-4 Battery voltage and trickle charge in standby to be within 5% of
manufacturer's specifications.
February 2000 J-311

Table J-15: Electrical Distribution
Block Title Text

System Description Electrical Distribution
Procedure Inspect and Clean Electrical Panels
Description
Special Tools Vacuum Cleaner
Materials
Reference Data
Warning Summary 1. Test to ensure all circuits are de-energized. 2. Closed circuit breaker
has high spring pressure. Keep clear of all moving parts.
Caution Summary
Reserved
Preliminary
Procedure
A Inspect and Clean Electrical Panels
practices.
A2 Open electrical panels or doors.
A3 Rack out circuit breakers and open switches as required.
moving parts.
A4 Inspect cables, connectors, terminal boards, and bus work for signs of
excessive heating and/or insulation damage.
A5 Inspect all exposed connections for secure mounting, corrosion,
damaged insulators, and signs of moisture contamination.
Note Loose connectors are identified through infrared thermography
inspection. Torque connectors to specified value or, if unknown,
maximum 25 in-lb.
CAUTION Do not over tighten connectors.
A6 Tighten loose connectors.
J-312 February 2000

A7 Inspect all exposed ground connections. Ensure connections are clean

and tight. Treat with corrosion inhibitor.
A8 Clean bus insulators.
A9 Clean conductors, terminal boards, enclosures, and panels with vacuum
cleaner.
A10 Ensure heaters (if installed) are working correctly.
on work order.
A12 Perform touchup painting as required.
A14 Close switches and rack in circuit breakers as required.
A15 Close panels and doors and return panel to service.
Engineer's Notes
EN1 Connector torque value, see specification SAE AIR1471. All values are
+ or - 12.5%.
EN1a 5/32-32: 25 in-lb.
EN1b 5/32-36: 26 in-lb.
EN1c 3/16-32: 42 in-lb.
EN1d 1/4-28: 95 in-lb.
EN1e 5/16-24: 185 in-lb.
EN1f 1/2-20: 800 in-lb.
February 2000 J-313

Table J-16: High/Med Volt Circuit Breaker
Block Title Text

System Description High/Medium Voltage Circuit Breaker
Procedure Inspect and Test Circuit Breaker
Description
Related Tasks PT&I-0002, PT&I-0005, PT&I-0008, E-0004
Labor (Hrs) 2 people/8 hr ea
Special Tools Breaker Timing Test Set, Contact Resistance Test Set, psychrometer (or
temperature/humidity meter), Thermometer
Materials
Reference Data ASTM Standard Test Methods (STM)
D-877-87 - Dielectric Breakdown Voltage of Insulating Liquids Using
Disk Electrodes (Dielectric Withstand Test)
D-1534-90 - Approximate Acidity in Electrical Insulating Liquids by
Color-Indicator Titration
Breaker Timing Test Set Operating Instructions
Contact Resistance Test Set Operating Instructions
Warning Summary 1. Test to ensure all circuits are de-energized. 2. Closed circuit breaker
has high spring pressure. Keep clear of all moving parts.
Caution Summary Do not over tighten connectors.
Reserved
Preliminary
6.
Procedure
A Inspect and Test Circuit Breaker
A1 Open breaker, de-energize and tag out in accordance with site safety
practices.
A2 Open electrical panels or cubicle doors.
A3 Install safety grounds if applicable.
A4 Disconnect line and load cables/bus from circuit breaker bushings or
rack breaker out and remove from cubicle.
J-314 February 2000

A5 Inspect breaker bushings and connectors for cracks, chips, looseness,

burning, and arcing/tracking.
A6 Inspect operating mechanism, for loose nuts, bolts, and pins.
A7 Inspect control wiring for burnt or frayed insulation.
Note 1 Loose connections are identified through infrared thermography
inspection. Torque connectors to specified value or, if unknown,
maximum 25 in-lb.
CAUTION Do not over tighten connectors.
A8 Tighten loose connectors.
on work order.
A10 Perform three point ground test. Record test results in Inspection Data
section.
moving parts.
A11 Perform breaker timing test. Record test results in Inspection Data
section.
Note 2 See Breaker Timing Test Set Operating Instructions for procedure.
A12 Perform related task PT&I-0005, Circuit Breaker Insulation Resistance.
A13 Perform related task PT&I-0008, Circuit Breaker Power Factor Test.
A14 Perform contact resistance test. Record test results in Inspection Data
section.
Note 3 See Contact Resistance Test Set Operating Instructions for procedure.
Note 4 Perform step A15 for vacuum type breakers. Perform step A16 through
A18 for oil filled type breakers.
A15 Perform vacuum bottle integrity test and/or a DC high-potential test at
2.5 times the rated AC voltage level.
Note 5 There is currently no standard for bottle integrity test. See manufacturer
instructions for guidance.
A16 Perform Dielectric Withstand Test (ASTM D-877-87).
A17 Perform Field Acidity Test (ASTM D-1534-90).
A18 Filter oil if needed.
Note 6 Oil will need to be filtered if dielectric breakdown is less than 24kV or
acidity is more than .3 gram KOH/ml
A21 Remove safety grounds.
A22 Reassemble circuit breaker and return to service.

ID-5 Oil Filled Breaker Oil Level
February 2000 J-315

ID-6 Oil Filled Breaker Oil Temperature (C)

ID-7 Three Point Ground, ohms
ID-8 Contact Resistance, Phase A
ID-9 Contact Resistance, Phase B
ID-10 Contact Resistance, Phase C
ID-11 Vacuum Bottle, Phase A
ID-12 Vacuum Bottle, Phase B
ID-13 Vacuum Bottle, Phase C
ID-14 Oil dielectric, kV
ID-15 Acidity, gram KOH/ml
Engineer's Notes
standard.
EN1a IEEE C37.11-1997 IEEE Standard Requirements for Electrical Control
for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current
Basis
EN1b ANSI/IEEE C37.09-1979, Standard Test Procedure for AC High-
Voltage Circuit Breakers Rated on a Symmetrical Current Basis.
EN2 Breaker timing test results should verify the integrity of the operating
mechanism. Compare current test with last test to confirm velocity,
travel, time, and contact wipe. Deviations from the manufacturers specs
indicate adjustment is required.
EN2a Contact resistance measurements normally range from 50 microhms to
1200 microhms. Consult manufacturers specifications for specific
values. Contact resistance of each phase should be within 10% of the
other phases.
EN2b Deviations indicate burnt or misaligned contacts, or misadjusted
operating mechanism.
EN3 A Vacuum Bottle Integrity Test and/or a DC High-Pot at 2.5 the rated
AC voltage level are go/no-go tests that verify the bottle is still in a
vacuum condition.
EN4 Oil tests for Oil Circuit Breakers can reveal the operating history and
condition of the contact assemblies. High acidity and low dielectric are
indicative of burning or arcing contacts, and/or high numbers of full load
operations
EN4a Levels outside the values identified in the procedure, Note 5, require the
oil to be filtered and the contact assemblies to be inspected.
EN5 Connector torque value, see specification SAE AIR1471. All values are
+ or - 12.5%.
EN5a 5/32-32: 25 in-lb.
EN5b 5/32-36: 26 in-lb.
EN5c 3/16-32: 42 in-lb.
J-316 February 2000

EN5d 1/4-28: 95 in-lb.

EN5e 5/16-24: 185 in-lb.
EN5f 1/2-20: 800 in-lb.
February 2000 J-317

Table J-17: Air Handler
Block Title Text

Procedure Number M-0001
System Description Air Handler
Procedure Inspect and Clean
Description
Periodicity A
Labor (Hrs) 2
Special Tools Vacuum Cleaner, Belt Tensiomometer
Materials Biological Control Tablets, Drive Belt(s)
Reference Data
Warning Summary
Caution Summary
Reserved
Preliminary
1 Review prior maintenance data including vibration data test results (if
available).
Notify operators or other local occupant before starting inspection.
Procedure
A Inspect and Clean
A1 Record air filter differential pressure (if installed).
A2 Record air temperature differential across cooling coils.
A3 Record air temperature differential across reheat coil.
practices.
A5 Open access covers and doors. Remove pulley and belt guards.
A4 Inspect pulley and belts. Replace belts if needed. Align belt sheeve and
adjust belt tension using tensiomometer.
Note When replacing belts, replace all belts on multi-belt pulley. Note on
work order.
A5 Clean cooler drains and condensate pans.
A6 Renew biological control tablet (if used).
A7 Clean fan or blower blades.
A8 Clean coils (cooling, heating, preheat, reheat).
A9 Clean motor air inlet and exit.
A10 Inspect motor mounts, seals, valves, gauges, fittings, ducts and other
parts and accessories for corrosion, leaks, looseness, and damage.
J-318 February 2000

A11 Inspect gages, thermometers, and indicators for proper calibration. Note
any overdue items on work order.
on work order.
A15 Replace pulley and belt guards.
A16 Close access covers and doors and return air handler to service.

ID-1 Air filter differential pressure.
ID-2 Air temperature differential across cooling coils. (F or C)
ID-3 Air temperature differential across reheat coil. (F or C)
Engineer's Notes
EN1 Biological control tablets are used to control fungus and bacterial growth
in the condensate pan. Contact environmental control for the proper
agents/tablets.
EN2 PT&I group needs to know if belts are changed or aligned.
February 2000 J-319

Table J-18: Chiller
Block Title Text

Procedure Number M-0002
System Description Chiller
Procedure 1. Open and Inspect
Description
2. Clean
Periodicity A
Labor (Hrs) 2 people/4 hr ea
Special Tools Halide Leak Detector, Electronic Leak Detector, Ultrasonic Noise
Detector
Materials Tube Plugging Kit, Oil Filter
Reference Data OEM Drawings and Procedures
Warning Summary 1. Liquid or gas may be environmental hazard.
2. Extreme pressure or vacuum may be present.
Caution Summary
Reserved
Preliminary
1 Review prior maintenance data including vibration data test results (if
available).
Notify operators or other local occupant before starting inspection.
Procedure
A Tube Leak Test
practices.
A2 Isolate fluid systems and tag out in accordance with site safety practices.
Note Check with site environmental control group before venting or draining
any gas or liquid from unit.
WARNING Liquid or gas may be environmental hazard.
WARNING Extreme pressure or vacuum may be present.
A3 Open condenser/cooler vent and equalize pressure.
A4 Drain condenser/cooler.
A5 Open condenser/cooler access covers or remove shell head. See OEM
for procedure.
A4 Perform tube leak test.
A5 Repair leaking tube. Plug tubes that can not be repaired.
A6 Record on work order tubes repaired or plugged.
J-320 February 2000

Note See OEM manual for tube location diagram.

B Clean and Inspect
B1 Replace oil filter, clean oil line strainer.
B2 Clean compressor oil cooler and gear box oil cooler.
B3 Calibrate chiller control system, load limiting system, and safety
controls.
WARNING Extreme pressure or vacuum may be present.
WARNING Liquid or gas may be environmental hazard.
B4 Drain purge unit.
B5 Clean purge condensing unit tubes, shell, water compartment, float and
chamber.
B6 Inspect mounts, seals, valves, gauges, fittings, and other parts and
accessories for corrosion, leaks, looseness, and damage.
B7 Inspect gages, thermometers, and indicators for proper calibration. Note
any overdue items on work order.
B8 Make minor repair. Contact supervisor if repairs are not possible. Note
on work order.
B9 Perform touchup painting as required.
B10 Perform related tasks, if any.
B11 Replace parts and covers removed for cleaning or testing.
B12 Fill and leak test unit.
B13 Return chiller to service.
B14 Remove debris from work-site.
Engineer's Notes
EN1 See manufacturers have specification for limit regarding maximum
number of plugged tubes.
EN2 Notify PT&I group following this procedure to schedule condition
monitoring retest.
February 2000 J-321

J-322 February 2000

Appendix K—SPECSINTACT Clauses with RCM Applications
The following table includes reference numbers, titles, and general RCM application descriptions
for clauses where RCM principles have been integrated into the SPECSINTACT. They can be
used as a ready reference to access SPECSINTACT for more detail
Clause Title General RCM Application

Division I General Requirements
01450 Quality Control
1.4.4.2 Inspection and Test Records Final test reports shall be provided to the
Contracting Officer for forwarding to the
Systems Engineer/Condition Monitoring
Office/Predictive Testing Group for inclusion
in the Maintenance Database.
01600 Product Requirements
2.1 Mechanical Materials and Material “cut sheets” and final test data to be
Equipment forwarded to CM Office/PT&I Group for
inclusion in Maintenance database
01750 Starting and Adjusting
1.3.1 Tests Required Tests are to be performed on systems
including electrical switchgear, protective
relaying, fluid and gas systems, pump/motor
combinations, boiler systems, hydraulic and
pneumatic control, condition/performance
monitoring systems, energy control and
monitoring systems and other assemblies and
components that need to be tested as an
interrelated whole.
1.3.2 Factory Tests Tests shall be performed by the factory to
verify proper build. These test results will be
used in the "Final Acceptance Test" section to
verify no shipping damage and proper
installation.
1.3.4 Final Acceptance Test Final test reports shall be provided to the
01780 Closeout Submittals
February 2000 K-323


1.3 Submittals Preventative Maintenance and Condition
Monitoring (Predictive Testing) and
Inspection schedules shall be submitted by the
Contractor with instructions that state when
systems should be retested.
Division II Site Work
02535 Packaged Lift Stations
1.2 Submittals Bearings shall be included in manufacturer's
catalog data. Preventative Maintenance,
Predictive Testing and Inspection procedures
for Package Lift Stations shall be submitted.
Procedures should include frequency of
preventative maintenance, frequency of
predictive testing and inspection, adjustment,
lubrication, and cleaning necessary to
minimize corrective maintenance and repair.
2.11 Balance Allowable vibration limits shall be in
accordance with ISO 1940/1, Table 1.
2.12 Shafts NOTE: When possible, specify sealed
bearings on motors. When properly installed
sealed bearings have as long a life as
conventional bearings, with almost no
maintenance requirements.
2.14 Lubrication Bearings on vertical-shaft pumps shall be self
lubricating, permanently sealed.
Division VII Thermal & Moisture Protection
07210 Building Insulation
3.10.1 Finished-Building Insulation Following a minimum of 90 days operation
(or installation), but no later than one year, the
Office/Predictive Testing Group should
inspect the installation using advanced
monitoring technologies such as Infrared
Imaging or Ultrasonic mapping.
07220 Roof and Deck Insulation
K-324 February 2000


3.3.5 Acceptance Following a minimum of 90 days operation
(or installation), but no later than one year
(but prior to the warranty expiration date), the
Imaging or Ultrasonic mapping. Final
acceptance will also depend upon providing
construction (as built) details to the
Contracting Officer Systems Engineer/
Condition Monitoring Office/Predictive
Testing Group for inclusion in the
Maintenance Database.
07510 Built-up Bituminous Roofing
07511 Built-up Asphalt Roofing
February 2000 K-325


07530 Single Ply Membrane
Roofing
3.9 Acceptance Following a minimum of 90 days operation
Contracting Officer.
Division IX Finishes
09915 Painting
--- Intro Note For harsh indoor environments (any area
subjected to chemical and/or abrasive action),
and all outdoor installations, reference Section
09960, "High Performance Coatings.”
09960 High Performance Coatings
--- Intro Note This section covers special coatings as
required for harsh indoor locations or
operations (any area subjected to chemical
and/or abrasive action), and all outdoor
installations.
2.2 Epoxy Coatings Epoxy resin coatings must be used where
surfaces to be coated require high corrosion
resistance, chemical resistance, bond strength,
UV resistance, and toughness.
K-326 February 2000


2.3 Polyurethane Coatings Polyurethane-based coatings must be used
where surfaces to be coated require high
abrasion resistance, good flexibility and
chemical resistance, UV resistance, and must
be a two-part, prepolymer, catalytic-cured
resin material
Division XIII Special Construction

13960 Carbon Dioxide
Extinguishing Systems
3.2.1 Preliminary Tests Storage batteries shall be given an impedance
test of each cell and the results recorded to be
used as baselines. Final Test Reports shall be
forwarded to the Systems Engineer/Condition
Monitoring Office/Predictive Testing Group
for inclusion in the Maintenance Database.
Division IXV Conveying Systems
14210 Electric Traction Elevators
2.3.2 Gears and Bearings When possible the use of sealed bearings is
encouraged. One of the major causes of
bearing failures is over lubrication and
lubrication contamination. Using sealed
bearings helps to eliminate this failure mode.
2.3.5 Hoist Motor When possible the use of sealed bearings is
2.4 Motor-Generator Set When possible the use of sealed bearings is
14240 Hydraulic Elevators
1.2 Submittals Submitted test results shall include Hydraulic
oil purity tests results.
2.2 Pump When possible the use of sealed bearings is
February 2000 K-327


2.3 Motor When possible the use of sealed bearings is
3.2.2 Tests Hydraulic oil purity test should include
measurement of viscosity and ferrographic
analysis to insure the oil is free from
contaminates.
14600 Hoists and Cranes
1.9.5 Bearings and Bearing Life When possible the use of sealed bearings is
2.5.8 Motor Bearings When possible the use of sealed bearings is
2.5.12 Ability to open and/or remove access covers is
Motor Controller required for maintenance activities. In
addition, access may be required to inspect
this device while circuits are energized (for
example, using infrared imaging). Minimum
distances to energized circuits is specified in
OSHA Standards Part 1910.333 (Electrical -
Safety-Related work practices).
3.8 Crane Electrification System Certification test reports shall be provided to
Factory Tests the Contracting Officer for forwarding to the
3.9 On-Site Complex Final test reports shall be provided to the
Electrification System Tests Contracting Officer for forwarding to the
14920 Monorail System
K-328 February 2000


2.16.4 Hoist Motors When possible the use of sealed bearings is
2.16.6 Motor Bearings When possible the use of sealed bearings is
2.16.7 Motor Controller NOTE: Ability to open and/or remove access
covers is required for maintenance activities.
In addition, access may be required to inspect
Division XV Mechanical
15003 General Mechanical
Provisions
1.7 Prevention Of Corrosion For all outdoor applications and all indoor
applications in a harsh environment refer to
Section 09960, "High Performance Coatings."
2.4 Painting For all outdoor applications and all indoor
3.1 Installation No installation shall be permitted which
blocks or otherwise impedes access to any
existing machine or system. Except as
otherwise indicated, emergency switches and
alarms shall be installed in conspicuous
locations. All indicators, to include gauges,
meters, and alarms shall be mounted in order
to be easily visible by people in the area.
3.2 Equipment Pads Equipment bases and foundations, when
constructed of concrete or grout, shall cure a
minimum of 28 or 14 days as specified before
being loaded.
15083 Duct Insulation
3.1 Installation of Insulation Insulation shall not impede access to duct
Systems covers/doors used for duct cleaning and/or
maintenance.
February 2000 K-329


in the Maintenance Database..
15085 Piping Insulation
in the Maintenance Database..
15135 Centrifugal Pumps
2.1.5 Balancing Pump impeller assemblies shall be statically
and dynamically balanced to ISO 1940/1-
1986, G6.3, G2.5, or G1.0 as specified.
2.1.11 Bearings and Lubrication Double-row ball or roller bearings for
engineered-quality pumps shall shall have an
L-10 rated life of not less than 30,000, 50,000,
or 80,000 hours as specified. Bearings shall
be permanently lubricated sealed bearings.
2.2.4 Balancing Pump impeller assemblies shall be statically
1986, G6.3, G2.5, or G1.0 as specified.
K-330 February 2000


2.2.9 Bearings And Lubrication Bearings shall be heavy-duty ball or roller
type and shall have an L-10 rated life of not
less than 30,000, 50,000, or 80,000 hours as
specified. Bearings shall be permanently
lubricated sealed bearings.
3.2 Grouting Grout shall cure a minimum of 28 days or as
specified before being loaded.
3.4 Alignment Provides pump and driver minimum
alignment specifications and doweling
requirements.
3.6 Pump Acceptance Prior to pump final acceptance vibration
analysis shall verify pump conformance to
specifications. Final test reports shall be
provided to the Contracting Officer for
forwarding to the Systems Engineer/Condition
15186 Condensate Pumps
1.2 Submittals Test Reports for condensate pumps shall
consist of Pump Flow Capacity Tests in
accordance with the paragraph entitled,
"Testing," of this section, Efficiency Tests and
Vibration Tests.
2.1.1 Pumps When pump is operating at its worst hydraulic
condition vibration readings shall conform to
ISO 1940/1, G6.3, G2.5, or G1.0 as specified.
3.1 Installation Pump and driver alignment specifications are
given based on the motor nominal operating
speed.
3.2.2 Acceptance Testing Pump shall be operated and the demonstration
shall verify that the pump is non-over loading
at any operating point and that the flow
capacity is as specified. Final test reports
shall be provided to the Contracting Officer
for forwarding to the Systems Engineer/
15445 Sump Pumps
February 2000 K-331


2 Products Pump and Motor vibration levels shall
conform to ISO Std. 1940/1 - (1986) Balance
Quality Requirements of Rigid Rotors -
Determination of Permissible Residual
Unbalance unless otherwise noted. Motor
vibration levels shall conform to NEMA
Specification MG-1, Motors and Generators,
Part 7 unless otherwise noted.
2.1.6 Bearings and Lubrication Bearings shall be sealed and grease-lubricated
and shall have an L-10 rating of not less than
80,000 hours in accordance with AFBMA 9 or
AFBMA 11.
3.1.1 Alignment
3.2.2 Pump Acceptance Prior to final acceptance, pump conformance
manufacturer's specifications shall be
demonstrated by checking vibration with
specified vibrometer while the pump is
operating against shutoff head, i.e., with
discharge valve closed. Final test reports shall
be provided to the Contracting Officer for
15510 Boilers
3.4 Final Acceptance Following a minimum of 90 days operation
Imaging or Ultrasonic detection. Final test
reports shall be provided to the Contracting
Officer for forwarding to the Systems
Engineer/Condition Monitoring
15610 Refrigeration Compressors
K-332 February 2000


2 Products Pump and Motor vibration levels shall
conform to ISO Std. 1940/1 - (1986) Balance
Quality Requirements of Rigid Rotors -
Determination of Permissible Residual
Unbalance unless otherwise noted. Motor
vibration levels shall conform to NEMA
Specification MG-1, Motors and Generators,
Part 7 unless otherwise noted.
2.1.2 Compressor Rotating parts shall be statically and
dynamically balanced at the factory to ISO
1940/1 1986, G6.3, G2.5, or G1.0 as specified
to eliminate vibration.
3.2.1 Vibration Specifies the type and characteristics of the
vibration analyzer the Contractor shall use.
Final test reports shall be provided to the
15625 Chilled Water Air
Conditioning
2.2.1 Centrifugal Fan Fan and Motor balance shall conform to ISO
Std. 1940/1 - (1986) Balance Quality
Requirements of Rigid Rotors - Determination
of Permissible Residual Unbalance unless
otherwise noted. Motor vibration levels shall
conform to NEMA Specification MG-1,
Motors and Generators, Part 7 unless
otherwise noted. When possible the use of
sealed bearings is encouraged. Fans driven by
motors rated over 7.5 HP [5.6 KW] shall be
furnished with access doors and other
provisions necessary to permit field balancing
of the rotating elements, addition of corrective
weights, and measurement of residual
unbalance. Bearings shall have an L-10 rated
life of not less than 30,000, 50,000 or 80,000
hours as specified in accordance with
AFBMA 9 or AFBMA 11. Removable metal
guard and adjustable rail specifications are
provided.
2.2.5 Electrical Requirements Ability to open and/or remove access covers is
required for maintenance activities.
February 2000 K-333


3.8 Acceptance Tests Specifies the type and characteristics of the
vibration analyzer the Contractor shall use.
Contracting Officer and forwarded to the
15626 Centrifugal Water Chillers
2 Products Provides pump and motor balance and
vibration level specifications.
2.2 Compressor Rotor assembly shall be statically and
dynamically balanced to ISO 1941/1-1986,
G6.3, G2.5, or G1.0 as specified.
2.7 Motors Hermetically sealed motors shall conform to
NEMA MG-1, ARI 520 and to requirements
for motors as specified. Bearings shall be oil-
lubricated, replaceable-sleeve, insertable type
permanently lubricated, rolling element type.
3.4 Alignment Provides pump and driver alignment
specifications.
3.5 Field Testing Prior to final acceptance, vibration analysis
shall verify pump and motor conformance to
specifications. Final test reports shall be
provided to the Contracting Officer for
15627 Reciprocating Water Chillers
2.3.1 Compressor Rotating parts shall be statically and
dynamically balanced to ISO 1940/1-1986,
G16, or G6.3 as specified.
15675 Air-cooled Condensers
2.2 Fans and Drives Fans shall be statically and dynamically
balanced to ISO 1940/1-1986, G6.3 or G2.5 as
specified. Bearings shall be permanently
lubricated sealed bearings.
15700 HVAC Systems
K-334 February 2000


2.7 Insulation Insulation shall not impede access to duct
covers/door used for duct cleaning and/or
maintenance.
2.11.3.1 Fans and Drives Fans shall be statically and dynamically
balanced to ISO 1940/1 1986, G6.3, G2,5,or
G1,0 as specified. Bearings shall be sealed
against moisture and dirt, prelubricated, and
suitable for not less than 10,000 operating
hours without need of re-lubrication.
Bearings shall be permanently lubricated
sealed bearings.
2.13.7.5 Propellers and Motors Propellers shall be dynamically balanced to
ISO 1940/1-1986, G6.3, G2.5, or G1.0 as
specified.
2.13.8.2 Fan and Drive Assembly Fan and Rotating elements shall be statically
1986, G6.3,.G2.5, or G1.0 as specified.
2.15 Air Handling Units (Factory Fan wheels shall be statically and dynamically
Assembled) balanced to ISO 1940/1-1986, G6.3, G2.5, or
G1.0 as specified.
3.9 Air-Handling Systems The Systems Engineer/Condition Monitoring
Testing Office/Predictive Testing Group should
inspect the installation during acceptance
testing using advanced monitoring
technologies such as Infrared Imaging or
Ultrasonic Listening.
3.10 Refrigeration Systems The Systems Engineer/Condition Monitoring
Testing Office/Predictive Testing Group should
3.11 Air And Hydronic Systems The Systems Engineer/Condition Monitoring
Testing, And Adjustment Office/Predictive Testing Group should
February 2000 K-335


3.12 Steam And Condensate The Systems Engineer/Condition Monitoring
Systems Testing Office/Predictive Testing Group should
3.13.1 Alignment Added section to provide alignment directions
and specifications.
3.13.2 Vibration Analyzer Added section to provide vibration analyzer
specifications.
3.13.3 Acceptance Tests Added section to provide acceptance test
requirements.
3.13.4 Test Records Final test reports shall be provided to the
Contracting Officer and forwarded to the
15720 Air Handling Units
1.2 General Requirements Fan and motor balance shall conform to ISO
otherwise noted.
2.1 Air Handling Unit AHU fan and motor shall be balanced to ISO
1940/1-1986, G6.3, G2.5, or G1.0 as
specified.
3.2 Vibration Analyzer Added section to provide vibration analyzer
specifications.
3.3 Acceptance Tests Added section to provide acceptance test
requirements.
3.4 AHU TESTING Final test reports shall be provided to the
15725 Air Handling
K-336 February 2000


2.1 General Fan Requirements Fan and motor balance shall conform to ISO
otherwise noted.
2.1.1 General Dynamically balance at the factory to ISO
1940/1-1986, G6.3, G2.5 or G1.0 as specified.
2.1.2 Bearings When possible the use of sealed bearings is
encouraged. Bearings shall have a certified
AFBMA 9 or AFBMA 11, L-10 minimum life
expectancy rating of 30,000, 40,000, 50,000,
80,000 hours as specified under load
conditions the service will impose.
2.3.3 Fan Wheel Wheel shall be statically and dynamically
balanced to ISO 1940/1-1986, G6,3, G2.5, or
G1.0.
2.3.4
2.3.5
2.4.3 Wheel shall be statically and dynamically
Fan Wheel balanced to ISO 1940/1-1986, G6,3, G2.5, or
G1.0 as specified.
2.5.3 Wheels shall be statically and dynamically
Fan Wheel balanced to ISO 1940/1-1986, G6,3, G2.5, or
G1.0 as specified.
3.2 Vibration Analyzer Added section to provide vibration analyzer
specifications.
3.3 Acceptance Added section to provide acceptance test
requirements.
15736 Computer Room Air
Conditioning Units
2.1 General Fan and motor balance shall conform to ISO
otherwise noted.
2.10 Compressors Compressor[s] shall be balanced to ISO
1940/1-1986, G6,3, G2.5 or G1.0 as specified.
February 2000 K-337


3.5.1 Vibration Analyzer Added section to provide vibration analyzer
specifications.
3.5.2 Acceptance Added section to provide acceptance test
requirements.
15740 Heat Pumps
2.2.3 Electrical Requirements All motors shall have copper windings, be
equipped with heavy duty ball bearings sealed
permanently lubricated bearings.
3.4 Insulation Insulation shall not impede access to duct
covers/doors used for duct cleaning and/or
maintenance.
3.7 Tests The Systems Engineer/Condition Monitoring
Ultrasonic Listening. Final test reports shall
15762 Air Coils
3.2 Tests The Systems Engineer/Condition Monitoring
Ultrasonic Listening. Final test reports shall
for inclusion in the Maintenance Database."
15764 Fan-coil Units
2.1 General Fan and motor balance shall conform to ISO
otherwise noted. NOTE: When possible the
use of sealed bearings is encouraged.
K-338 February 2000


2.4 Fan Fan shall be balanced dynamically and
statically to ISO Std. 1940/1 at the factory,
after assembly in unit.
3.3
3.4
15766 Unit Heaters
1.1
1.3
2 Products When possible the use of sealed bearings is
encouraged. Provides fan and motor balance
and vibration level specifications.
15838 Power Ventilators
2.3 Fan Type(s) When possible the use of sealed bearings is
encouraged.
2.5 Fan Motor When possible the use of sealed bearings is
encouraged.
3.3 Acceptance Added section to provide acceptance test
requirements.
3.3 Movable parts of dampers and related
Lubrication operating hardware shall be lubricated in
accordance with manufacturer's printed
instructions and shall operate smoothly and
quietly without binding.
3.4 Final Test Reports Final test reports shall be provided to the
15902 Control systems
2.8.2 Bearings When possible the use of sealed bearings is
encouraged.
2.11 Individual System Control Ability to open and/or remove access covers is
Panels required for maintenance activities. In
addition, access may be required to inspect
February 2000 K-339


3.5 Testing, Calibration, and The Systems Engineer/Condition Monitoring
Acceptance Office/Predictive Testing Group should
3.8
15950 Testing and Balancing
3 Execution The Systems Engineer/Condition Monitoring
3.3.7
3.7 Test Reports Final test reports shall be provided to the
Division XVI Electrical
16003 General Electrical Provisions
Metallic materials shall be protected against
corrosion. Equipment enclosures shall be
given a rust-inhibiting treatment and the
standard finish by the manufacturer when
used for most indoor installations.
2.5 Painting Refer to Section 09960, "High Performance
Coatings," for requirements outdoors or in
harsh environments.
16050 Basic Electrical Materials
and Methods
Metallic materials shall be protected against
corrosion. Equipment enclosures shall have
the standard finish by the manufacturer when
used for most indoor installations.
K-340 February 2000


3.7 Panelboards Ability to remove access covers is required for
maintenance activities. No equipment shall be
mounted within 36 inches of the front of the
panel.
3.8 Dry-Type Distribution Ability to remove access covers is required for
Transformers maintenance activities. Minimum distances to
energized circuits is specified.
3.10 Painting Section 09960, "High Performance Coatings"
was added to the specifications.
3.11 Field Testing Adds final acceptance wire, cable and
transformer inspection specifications. Final
test data shall be provided to the Contracting
16124 Medium Voltage Cables
2.4 Multiple-Conductor Shielded Cross-linked polyethylene insulation has been
Cables shown to tree when installed in wet
environments. Also added additional cables
to recommended list.
3.2 Field Testing Added testing specifications including
radiographic tests of potheads at the discretion
of the Contracting Officer. Final test reports
shall be provided to the Contracting Officer
for forwarding to the Systems Engineer/
16125 Motors
1.3 Submittals Data for electric motors rated over 20hp and
those specified to meet a special vibration
class in accordance with NEMA MG 1
indicate number of: Rotor Bars, Stator Slots,
rotational Speed, Cooling Fan Blades Bearing
Manufacturer, Bearing Style, Bearing Type,
Balls/Elements, Commutator Bars,
Communtator Brushes Firing Frequencies
(for variable speed motors).
February 2000 K-341


2.1 Equipment Design, fabrication, testing, and performance
of motors shall be in accordance with NEMA
MG 1 and ISO 1940/1. Testing and
performance of polyphase induction motors
shall be in accordance with IEEE Std 112,
Method B. Efficiency labeling shall be in
accordance with NEMA MG 1. Allowable
vibration limits shall be in accordance with
ISO 1940/1, Table 1.
3.2 Site Testing Added additional testing specifications and
that final test data shall be forwarded to the
responsible systems engineer for inclusion in
the Predictive Maintenance Program/
Database.
16275 Transformers
1.3 Submittals Test Report submittals for the following test
were added: Power Factor Tests, Insulation
Resistance Tests, and Insulation Power
Factor(Doble) Tests.
1.4 Qualification Testing Transformer manufacturer's standard tests
were expanded to include; insulation power
factor (Doble) tests, insulation oil tests, and
dielectric tests. For oil-filled units
manufacturer shall certify that the oil contains
no PCB's and shall affix a label to that effect
on the transformer tank and on each oil drum
containing the insulating oil.
2.2 Factory Finish For all outdoor applications and all indoor
3.2 Field Testing For transformers rated under 100KVA and
less than 4160 Volts on both primary and
secondaries power factor testing is an optional
acceptance test. Transformers shall be tested
in accordance with IEEE Std. 62.
3.2.1.1 Dielelectric Tests Liquid filled transformers shall have the
insulating liquid dielectrically tested after
installation and before being energized.
Insulating liquid shall be tested in accordance
with ASTM D 877, and breakdown voltage
shall be not less than 2, 5, or 8,000 volts as
specified.
K-342 February 2000


3.2.1.2 Power Factor Tests Liquid filled transformers shall have the oil
power factored at 20 degrees C, per ASTM D
924 prior to being energized. Results shall not
be greater than 0.5 percent at 20 degrees C.
3.2.2 Insulation-Resistance Tests Added additional test specifications
3.2.3 Insulation Power Factor Transformer windings shall be given an
(Doble) Tests insulation power factor test and winding
excitation test in accordance with ANSI IEEE
C57.12.90. Insulation power factor shall not
exceed 0.5 percent for new liquid filled units.
New dry type units can have power factors up
to 5.0 percent and still be acceptable.
3.2.4 Acceptance Final test reports shall be provided to the
16276 Medium Voltage
Transformers
1.4 Qualification Testing Added oil condition (acidity, water, power
factor, dissolved gas, and dielectric), and the
insulation power factor test (Doble Test).
Maximum acceptable insulation power factor
test value is 5 percent. Tests shall be
conducted in accordance with IEEE
C57.12.90, IEEE Std. 62, ASTM D 3612, and
ASTM D 3487. Manufacturer shall certify
that insulating oil contains no PCB's and shall
affix a label to that effect on the transformer
tank and on each oil drum containing the
insulating oil.
2.8 Coils For transformers to be installed in high fault
current areas aluminum and sheet windings
should be avoided.
2.11 Insulating Oil Neutralization Number shall not be greater
than .03 gm KOH/ml when measured in
accordance with ASTM D 974. Emulsified
water shall not exceed 25ppm at 20 degrees C.
When measured in accordance with ASTM D
1533. Power factor shall not exceed .5
percent at 20 degrees C when measured in
accordance with ASTM D 924.
February 2000 K-343


After fabrication, all exposed ferrous metal
surfaces of the transformer and component
equipment shall be cleaned and painted.
3.2 Field Testing Upon satisfactory completion of the insulation
resistance test the transformer windings shall
be given an insulation power factor test and an
excitation test. Added oil tests to be
performed after electrical tests of the
transformer. Transformer shall not be
energized until recorded test data have been
approved by the Contracting Officer. Final
test reports shall be provided to the
16285 Medium Voltage Power
Factor Correction
1.2 Submittals Added report on Capacitance Value Tests.
2.4 Prevention of Corrosion Section on corrosion prevention (painting) of
capacitor equipment was added.
3.2 Field Testing Additional high-voltage capacitor equipment
test specifications were added. Final test
reports shall be provided to the Contracting
16286 Overcurrent Protective
Devices
1.2 Submittals Factory Test Reports shall be submitted for
Power, High Voltage, and Oil Circuit
Breakers in accordance with ANSI C37.09
and shall include the following: Dielectric
Tests, Bushing Tests, Insulating Oil Tests,
Timing Tests, and Insulation Power Factor
tests.
K-344 February 2000


2.4.5 Oil Circuit Breakers Oil for oil circuit breakers shall conform to
ASTM D 3487. Oil circuit breakers shall be
factory tested in accordance with ANSI
C37.09.
2.12 Finish For all outdoor applications and all indoor
3.2 Field Testing Additional equipment test specifications were
added. Final test reports shall be provided to
the Contracting Officer for forwarding to the
16325 Load Break Switches
3.1 Installation Final switch acceptance specifications were
added.
16326 Air-Break Switches
3.1 Installation Final switch acceptance specifications were
added.
16327 Oil Switches
2.2 Accessories For all outdoor applications and all indoor
3.3 Field Testing Load break switch assembly insulation-
resistance test was changed from 2500V to
5000V.
3.4 Inspection Final test reports shall be provided to the
16328 Load Break SF6 Gas
Switches
2.6 Factory Finish For all outdoor applications and all indoor
3.3 Field Testing Provides additional field test specifications.
16345 Motor Control
February 2000 K-345


2.3 Construction Access is required to inspect the motor control
center while circuits are energized (for
3.2 Field Testing Provides additional field test specifications.
16365 Primary Unit Substation
1.3 Submittals Power Transformers, Transformer Tanks,
Bushings, Transformer Cores, and
Transformer Coils were added to
Manufacturer's Catalog Data requirements.
Power Transformers, Transformer Tanks,
Bushings, Transformer Cores, and
Transformer Coils were added to fabrication
drawings to be submitted. The following
were added to test reports : Insulation Power
Factor Tests, Oil Power Factor Tests, Oil
Acidity Tests, Water-in-oil (Karl Fischer)
Tests, Dissolved Gas Analysis, Sound Tests,
Impulse Tests, Short Circuit Tests, and
Bushing Tests.
2.1 Equipment Standards ANSI C37.121 was added to standards.
2.4.1 Transformers For transformers to be installed in high fault
current areas aluminum and sheet windings
should be avoided. Transformer oil
neutralization Number shall not be greater
than .03 gm KOH/ml when measured in
accordance with ASTM D 974. Emulsified
water shall not exceed 25 ppm at 20 degrees
C, when measured in accordance with ASTM
D 1533. Power factor shall not exceed 0.5
percent at 20 degrees C when measured in
accordance with ASTM D 924. The
manufacturer shall certify that the oil contains
no PCB's and shall affix a label to that effect
on the transformer tank and on each oil drum
containing the insulating oil.
K-346 February 2000


2.5.1 Switchgear And Auxiliary Ability to remove access covers is required for
Equipment Compartments maintenance activities. In addition, access
may be required to inspect these devices while
circuits are energized (for example, using
infrared imaging). Minimum distances to
energized circuits is specified in OSHA
Standards Part 1910.333 (Electrical - Safety-
Related work practices).
2.11
2.11.2 Shop Finishing For all outdoor applications and all indoor
3.2 Field Testing The following transformer tests were added:
Insulation Power Factor TestsWinding
Excitation Tests Insulating Oil Tests
Transformer windings and the main bus of
primary-unit substations shall be subjected to
insulation-resistance and insulation power
factor test.
16366 Secondary Unit Substation
2.3.1 Switchgear and Auxiliary Ability to open access covers is required for
may be required to inspect this device while
2.4.1 Transformers, Outdoor Added the following to transformer oil
specifications: Neutralization Number shall
not be greater than .03 gm KOH/ml when
measured in accordance with ASTM D 974.
Emulsified water shall not exceed 25 ppm at
20 degrees C, when measured in accordance
with ASTM D 1533. Power factor shall not
exceed 0.5 percent at 20 degrees C when
measured in accordance with ASTM D 924.
February 2000 K-347


2.5.1 Switchgear and Auxiliary Ability to open access covers is required for
2.6.3
3.1
3.2 Field Testing A number of transformer tests were added
Final test data shall be provided to the
16445 Switchgear Assemblies
1.6.1
2.2.1 Switchgear and Auxiliary Ability to remove access covers is required for
Compartments maintenance activities. In addition, access
3.2 Field Testing Final test data shall be provided to the
3.5 Energizing Switchgear Final test data shall be provided to the
Assemblies Contracting Officer for forwarding to the
K-348 February 2000

RCM Handbook-1

Uploaded by

Copyright:

Available Formats

RCM Handbook-1

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RCM Handbook-1

Uploaded by

Copyright:

Available Formats

What is Reliability Centered Maintenance and what are its main principles?

What is Reliability Centered Maintenance and what are its main principles?

What are the different components of an RCM program?

What are the different components of an RCM program?

NATIONAL AERONAUTICS

AND SPACE ADMINISTRATION

RELIABILITY CENTERED MAINTENANCE

Chapter 2Reliability Centered Maintenance (RCM) Approach ............................................ 2−7

Chapter 3 RCM Program Components .............................................................................. 3−27

3.4.5 Reliability Engineering ..................................................................... 3B44

Chapter 4 Predictive Testing & Inspection (PT&I) Technologies ...................................... 4B57

Chapter 5CRCM Requirements During Facilities Acquisition............................................. 5B101

5.4 Maintenance and Operations (M&O) ........................................................... 5B104

Chapter 6CRCM Considerations During Facilities Operation.............................................. 6B105

Chapter 7CRCM Contract Clauses .......................................................................................7B111

Chapter 8CPT&I Criteria.................................................................................................... 8B137

February 2000 iii

Chapter 9CChecklists for RCM Quality Assurance .............................................................. 9B149

Chapter 10CManagement Indicators .................................................................................. 10B153

Appendix ACGlossary ........................................................................................................ AB167

2-1. Criticality/Severity Categories...................................................................2-18

3–3. Balance Quality Grades for Various Groups of Representative Rigid

1-1. Components of an RCM Program................................................................1-1

2-3. Reliability Centered Maintenance (RCM) Decision Logic Tree.................2-12

Reactive Preventive Predictive Proactive

• Small items • Subject to wear- • Random failure • RCFA

Figure 1–1. Components of an RCM Program

1.2 Historical Evolution of RCM

February 2000 1-1

1-2 February 2000

Thirty Identical 6309 Deep Groove

Figure 1-2: Bearing Life Scatter

February 2000 1-3

1.3 Purpose of This Guide

• An Introduction to Root Cause Failure Analysis

• An Overview of PT&I Technologies

• Guidelines for Establishing Monitoring Intervals

• Requirements for the Certification of PT&I Personnel

• In-service Criteria for Facilities Equipment and Systems

• Guidelines for Developing Procurement Specifications and Criteria

• Contract Clauses for Planning, Design, Construction, and Maintenance

• Guidelines for Performing Facilities Condition Assessment in an RCM

1.4 Applicability and Use of This Guide

1-4 February 2000

Management Handbook5. Proactive techniques such as machinery alignment and balance

Run-to-Failure of non-safety Proactive

Feedback to designers to improve the inherent

Establish material holding location.

Figure 1-3. RCM Strategy and Process

February 2000 1-5

Intentionally Left Blank

1-6 February 2000

Chapter 2 - Reliability Centered Maintenance (RCM)

2.2 RCM Analysis

• What does the system or equipment do; what is its function?

• What functional failures are likely to occur?

February 2000 2-7

• What are the likely consequences of these functional failures?

Environmental, Health, and Safety

Figure 2-1. RCM Analysis Considerations