QuickSteamer

USERS GUIDE
1770, 1970, 2080, 2090 SERIES

Safety Instructions

Product View

Assembly

6-8

Operation

8-9

Maintenance and Care

10

Troubleshooting

10

Consumer Services

11

Replacement Parts

12

Warranty

ug120-4071_1770_908.indd 1

10/14/08 1:05:58 PM

Thanks for buying a BISSELL QuickSteamer

Were glad you purchased a BISSELL QuickSteamer lightweight deep cleaner.

Everything we know about floor care went into the design and construction
of this complete, high-tech home cleaning system.
Your QuickSteamer is well made, and we back it with a limited one-year
warranty. We also stand behind it with a knowledgeable, dedicated
Consumer Services department, so, should you ever have a problem, youll
receive fast, considerate assistance.
My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is
a global leader in the design, manufacture, and service of high quality
homecare products like your QuickSteamer.
Thanks again, from all of us at BISSELL.

Mark J. Bissell
President and Chief Executive Officer

22

www.bissell.com

ug120-4071_1770_908.indd 2

800.237.7691

10/14/08 1:05:59 PM

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should be observed, including the following:
Read all instructions before using your QUICKSTEAMER

WARNING: To reduce the risk

of fire, electric shock, or injury:

Do not immerse.
Use only on surfaces moistened by cleaning process.
Always connect to a properly grounded outlet.
See Grounding Instructions.
Unplug from outlet when not in use and before
conducting maintenance or troubleshooting.
Do not leave machine when it is plugged in.
Do not service machine when it is plugged in.
Do not use with damaged cord or plug.
If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into water,
have it repaired at an authorized Service Center.
Do not expose to rain. Store indoors.
Do not pull or carry by cord, use cord as a handle, close
door on cord, pull cord around sharp corners or edges, run
appliance over cord, or expose cord to heated surfaces.
Do not carry the appliance while in use.
Do not unplug by pulling on cord. Unplug by grasping
the plug, not the cord.
Do not handle plug or appliance with wet hands.
Do not put any object into appliance openings, use with
blocked opening, or restrict air flow.
Do not expose hair, loose clothing, fingers or body
parts to openings or moving parts.
Do not pick up hot or burning objects.
Do not pick up flammable or combustible materials
(lighter fluid, gasoline, kerosene, etc.) or use in the
presence of explosive liquids or vapor.
Do not use appliance in an enclosed space filled
with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable
dust, or other explosive or toxic vapors.
Do not pick up toxic material (chlorine bleach, ammonia,
drain cleaner, gasoline, etc.).
Do not modify the 3-prong grounded plug.
Do not allow to be used as a toy.
Do not use for any purpose other than described in
this Users Guide.
Use only manufacturers recommended attachments.
Use only cleaning products formulated by
BISSELL for use in this appliance to prevent
internal component damage. See the Cleaning
Fluid section of this guide.
Keep openings free of dust, lint, hair, etc.
Keep appliance on a level surface.
Turn off all controls before unplugging.
Be extra careful when cleaning stairs.
www.bissell.com

ug120-4071_1770_908.indd 3

Close attention is necessary when used by

or near children.
WARNING: The Power Cord on this product contains
lead, a chemical known to the State of California to
cause birth defects or other reproductive harm.
WASH HANDS AFTER HANDLING.

SAVE THESE
INSTRUCTIONS.

This model is for household use only.

Commercial use of this unit voids the
manufacturers warranty.

GROUNDING
INSTRUCTIONS

This appliance must be connected to a grounded

wiring system. If it should malfunction or break
down, grounding provides a safe path of least
resistance for electrical current, reducing the risk of
electrical shock. The cord for this appliance has an
equipment-grounding conductor and a grounding
plug. It must only be plugged into an outlet that is
properly installed and grounded in accordance with
all local codes and ordinances.
Grounded
Outlets

Grounding Pin

WARNING:

Improper
connection of the equipment-grounding
conductor can result in a risk of electrical
shock. Check with a qualified electrician or
service person if you arent sure if the
outlet is properly grounded. DO NOT MODIFY
THE PLUG. If it will not fit the outlet, have
a proper outlet installed by a qualified
electrician. This appliance is designed for
use on a nominal 120-volt circuit, and has
a grounding attachment plug that looks
like the plug in the drawing above. Make
certain that the appliance is connected to
an outlet having the same configuration as
the plug. No plug adapter should be used
with this appliance.

800.237.7691

33

10/14/08 1:05:59 PM

Product View
Quick Release
Cord Wrap

Spray Trigger

Handle
Assembly

Power Cord
Upper Body

Lower Cord
Wrap
Lower Body

Solution Tank

Vent Cover
(Containing
Foam Filter)

Large Easy
Rolling Wheels

Collection
Tank

Collection Tank Latch

Detent
Power Lever
Switch

Removable Nozzle

WARNING:
To reduce the risk of fire and electric shock due to internal
Cleaning fluid

component damage, use only BISSELL cleaning fluids intended

for use with the deep cleaner. Non-BISSELL cleaning solutions
may harm the machine and void the warranty.

Keep plenty of genuine BISSELL Fiber Cleansing Formula on hand so you can clean and protect
whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas. Non-BISSELL
cleaning solutions may harm the machine and will void the warranty.

48 oz. BISSELL
Fiber Cleansing
Formula with
Scotchgard
Protector
item # 0710

48 oz. BISSELL
Multi- Allergen
Removal
Formula with
Scotchgard
Protector
item # 0720
www.bissell.com

ug120-4071_1770_908.indd 4

48 oz. BISSELL
Pet Odor and
Soil Removal
Formula with
Scotchgard
Protector
item # 0730

48 oz. BISSELL
Natural Orange
Extract Formula
with Scotchgard
Protector
item # 0740

48 oz. BISSELL
Lavender Essence
Formula with
Scotchgard
Protector
item # 0750

43 oz. BISSELL
3X Concentrated
Fiber Cleansing
Formula with
Scotchgard
Protector
# 0716

32 oz.
22 oz.
BISSELL BISSELL
Hard Floor Tough Stain
Solutions PreCleaner
Formula
item #
item #
0400
0484
800.237.7691

10/14/08 1:06:03 PM

How to Use this Guide

This users guide has been designed to help you
get the utmost satisfaction from your BISSELL
QuickSteamer lightweight deep cleaner. Youll
find assembly and operating instructions, safety
precautions, as well as maintenance and
troubleshooting instructions. Please read this
guide thoroughly before assembling your
deep cleaner. Pay particular attention to the
product diagram, assembly instructions, and
part names. Locate and organize all parts before
assembly. Familiarize yourself with the parts
and where they go. Following this users guide
will greatly enhance your ability to get the most
performance from your BISSELL QuickSteamer
for many years.
Your QuickSteamer comes in three, easy to
assemble components:
Handle assembly
Upper body assembly
Solution tank
Also includes 3 Phillips head screws.
The only thing you will need to assemble your cleaner is
a Phillips head
screwdriver.

1.

2.

Assembly
1.
2.
3.
4.
5.

Slide upper body into lower body.

Secure with screws.

Slide handle assembly down into upper body
until it will go no further. Align screw slots.
Secure with screw.
Place solution tank on back of unit.

Product features

3.

4.

Solution Tank:
Holds 1/2-gallon of cleaning solution.
Collection Tank:
Holds 1/2-gallon of dirty water.
Power Cord:
For storage, wrap power cord around upper and lower cord
wraps, and secure plug to cord with molded clip.

www.bissell.com

ug120-4071_1770_908.indd 5

5.

800.237.7691

10/14/08 1:06:04 PM

Operation
Before you clean
1.
2.
3.
4.

5.
6.

Plan activities to give carpet time to dry.

Remove easily moved furniture (chairs, lamps,
coffee/cocktail tables, etc.) from room if needed.
Vacuum carpet thoroughly.
Decide where to begin and end your job.
Clean in 3 X 4 sections, starting in areas farthest
from exit. Plan to leave a path open to empty
soiled water and refill cleaner.
Carpeting will dry in three to four hours, depending
on carpet style and air circulation in room. A floor
fan speeds drying.
Replace furniture on damp carpeting by placing
waxed paper under legs until floor dries completely.

Fill the tank

Warning:

To reduce the risk of fire, use

only BISSELL advanced
cleaning formulas for deep
cleaning machines. Use of
cleaning formulas that contain
lemon or pine oil may damage
this appliance and void
warranty. Chemical spot
cleaners or solvent-based soil
removers should not be used.
These products may react with
the plastic materials used in
your QuickSteamer, causing
cracking or pitting.

1.

Remove the solution tank by lifting it straight up,

then away from the lower body.
2. Unscrew the black cap at the bottom of the
solution tank.
3a. Add one of the BISSELL advanced cleaning
formulas for deep cleaning machines to the formula fill line on the solution tank. Fill the rest of
the tank with hot (not boiling) tap water to the
water fill line. Replace and tighten the black cap.
3b. If using the BISSELL 3X Concentrated Fiber
Cleansing Formula: Add 1/2 capful of 3X
Concentrated Fiber Cleansing formula to clean
water/solution tank, and then fill with hot water to
the line.

4.
5.

Pre-treat stubborn stains and highly soiled

carpet in hallways and other high-traffic areas.

2.

Always vacuum thoroughly before

you deep clean. If possible, move
large furniture to an area you will
not be cleaning.
2.

Place solution tank on lower body.

Rotate Quick Release Cord Wrap to release the
Power cord and plug into an outlet.

Pre-Treating

1.

Tip:

Using BISSELL Tough Stain pre-cleaner, generously

spray evenly over soiled area, do not overwet carpet.
Wait 3 -5 minutes before deep cleaning.

www.bissell.com

ug120-4071_1770_908.indd 6

Tip:
Deep cleaning
spots, spills and
high traffic areas
on a regular basis
can prolong
carpet life.

800.237.7691

10/14/08 1:06:04 PM

Operation

Tip:

Carpet cleaning

It is recommended
that every time your
solution tank needs
refilling, that you empty
the contents of the
collection tank. If the
collection tank gets too
full, you may begin to
see foam spitting out
of the vent cover. If this
happens empty the
collection tank.

1. With your foot, press the red power switch

2.
3.
4.
5.
6.
7.
8.

[located in foot of unit] ON.

With foot, press the detent lever on right side of
lower body.
Depress spray trigger to spray cleaning solution.
Do not overwet.
To suction up water, repeat motion over same
area without pressing trigger.
Repeat steps 3 and 4 until no more dirt can be removed.
Continue to clean entire carpet, working in
3 x 4 sections.
Empty the collection tank when dirty water reaches
the full line, or when the solution tank is empty. See
page 8 for instructions.
If floor nozzle stops spraying, turn power switch
OFF and check water and cleaning solution levels.
Refill if needed.

To empty the collection tank

1.
2.
3.

a.

b.

c.

e.

Turn power switch OFF.

Unplug power cord from outlet.
Remove and empty collection tank.
a. Release collection tank latches [1 each side]

by pulling up from bottom of latch and then out.

b. Carefully remove collection tank from

lower body by lifting handle.

c. Carry collection tank to a toilet or sink.

To empty, pour out contents using

opening at back of tank.
d. Rinse collection tank thoroughly.
e. Remove lint and hair from red gasket in
base of unit. (Do not remove gasket)

4.
5.

Clean nozzle window by lifting latch and removing

from machine. Rinse under running water. When
finished replace nozzle and secure with latch.
Replace collection tank on lower body and
secure with latches.

Dirty
4.

Hard floor cleaning

1.
2.

Attach hard floor tool to unit.

Remove the collection tank (refer to steps 3a and
b in the Maintenance and care section on page 8)
A. For 1770/1970 series it is necessary to
remove the cross action brush first.
Using your thumbs squeeze the 2 grey tabs
towards the outside of the unit. Push down
at the same time and release
the cross action brush.
www.bissell.com

ug120-4071_1770_908.indd 7

800.237.7691

10/14/08 1:06:05 PM

Operation

3.

3.

Hard floor cleaning (continued)

3.
4.
5.
6.
7.

Attach the hard floor tool by hooking it into the

front of the removable nozzle and swinging it
down until the tabs pop into place.
Replace the collection tank. Be sure to attach the
2 latches.
Fill solution tank with BISSELL Hard Floor
Solutions to FORMULA fill line.
Fill solution tank with hot (not boiling) tap water
to the WATER fill line.
Follow steps 1-8 in Carpet cleaning section above.

Maintenance and care

Machine storage
1.
2.

Wrap power cord around Quick Release Cord

Wrap on side of QUICKSTEAMER.
Wipe all surfaces with a soft cloth. Store cleaner
upright in a protected, dry area.

NOTE: You may have cleaning solution

remaining in the clean/solution tank. You may
store your QuickSteamer this way for the next
cleaning task, but never keep soiled solution in
the collection tank.

OR
2080/2090 series

2080/2090 Series

1770/1970 series

WARNING:
To reduce the risk of injury

from moving parts and/or

electrical shock, turn power
switch OFF and disconnect
plug from electrical outlet
before performing maintenance
or troubleshooting checks.

CAUTION:
Do not store unit

where freezing may

occur. Damage to
internal components
may result.

www.bissell.com

ug120-4071_1770_908.indd 8

800.237.7691

10/14/08 1:06:06 PM

Maintenance and care

To install the replacement brush belt

Brush Cover
3.

4.

*QuickSteamer PowerBrush models only

1.

Turn the machine off and unplug from wall outlet.

2. Remove solution and collection tanks.
3. Lie machine down to access the bottom of
5.
the machine.
4. With a Phillips head screwdriver, unscrew
the brush cover and remove.
5. Remove the brush end cap and remove belt from
brush.
6. Brush can now be removed.
7. Belt can be removed by sliding off the motor pulley. 6.
8. Clean or replace belt. Attach belt to motor pulley
and brush, insert brush into right side end cap.
9. Reattach the left end cap and slide brush back
into place.
10. Replace the brush cover and screw into place.
8.

9.

5a.

7.

10.

Troubleshooting
Reduced spray or no spray
Possible Cause
Remedy
1. Clean tank empty
1. Refill tank with water
and formula
2. Lint screen on solution tank cap clogged
2. Soak solution tank cap in warm
water and then rinse under
running water

Deep cleaner not picking up cleaning solution

Possible Cause
Remedy
1. Collection tank not aligned/secured
1. Check tank proper alignment
and secure with side latches
2. Dirty tank full
2. Empty tank
3. Removable nozzle installed improperly
3. Align four "hooks" into bottom
first, then snap into place on top

www.bissell.com

ug120-4071_1770_908.indd 9

800.237.7691

10/14/08 1:06:07 PM

Troubleshooting
Deep cleaner not picking up cleaning solution (Continued)
Possible Cause
Remedy
4. Removable nozzle full of debris
4. Remove nozzle and rinse under
running water
5. Red lint screen under collection tank clogged
5. Remove debris from lint screen
Other Maintenance or Service not included above should be performed by
an authorized service representative.

Thank you for selecting a BISSELL product.

Please do not return this product to the store

For any questions or concerns, BISSELL is happy to be of service.
Contact us directly at 1-800-237-7691.

BISSELL Consumer Services

For information about repairs or replacement parts, or questions about your warranty, call:

BISSELL Consumer Services

1-800-237-7691
Monday - Friday
Saturday

8 a.m. 10 p.m. ET
9 a.m. 8 p.m. ET

Or write:
BISSELL HOMECARE, INC
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services

Or visit the BISSELL website - www.bissell.com

When contacting BISSELL, have model number of unit available.
Please record your Model Number: ___________________
Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event
of a warranty claim. See "Warranty" on page 12 for details.

Please register your new BISSELL product at

www.bissell.com/productregistration
10

www.bissell.com

ug120-4071_1770_908.indd 10

800.237.7691

10/14/08 1:06:08 PM

Replacement parts - BISSELL QuickSteamer

Item

Part No.

Part Name

QuickSteamer 1770/1970 Series

1
2
3
4
5
6

203-5519 Handle Assembly

203-5545
Cross Action Brush
203-5537
Solution Tank (Includes Cap and Insert Assembly)
203-5522
Collection Tank
203-5547 Hard Floor Tool
203-5541
Solution Tank Cap and Insert Assembly

QuickSteamer PowerBrush 2080/2090 Series

1
3
4
6
7
8
9

203-5520 Handle Assembly

203-5540
Solution Tank (Includes Cap and Insert Assembly)
203-5523
Collection Tank
203-5541
Solution Tank Cap and Insert Assembly
203-5546
DirtLifter PowerBrush
203-5549
Belt
203-5548 Hard Floor Tool

Formulas:

10
0710A
Fiber Cleansing Formula 48 oz.
11
0716
3x Concentrated Fiber Cleansing Formula with

Scotchgard Protector 43 oz.
12
0720A
Multi-Allergen Removal Formula 48 oz.
13
222-0400
Tough Stain PreCleaner
14
0730A
Pet Odor and Soil Removal Formula 48 oz.
15
0484 Hard Floor Solutions 32 oz.
1

10

11

12

13

14

15

Earn Rewards Points!

To qualify you for discounts, rebates, and other BISSELL perks.

Visit www.bissell.com/rewards to learn more.

www.bissell.com

ug120-4071_1770_908.indd 11

800.237.7691

11

10/14/08 1:06:11 PM

Warranty - BISSELL QuickSteamer

This warranty gives you specific legal rights, and you may also have other rights which may vary from state
to state. If you need additional instruction regarding this warranty or have questions regarding what it may
cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.

Limited One Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL
Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELLs
option, free of charge from the date of purchase by the original purchaser, for one year any defective or
malfunctioning part.
See information below on "If your BISSELL product should require service".
This warranty applies to product used for personal, and not commercial or rental service. This warranty does not
apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused
by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not
covered.

If your BISSELL product should require service:

Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Services.
Website or E-mail:
www.bissell.com
Use the Customer Services tab.
Or Call:
BISSELL Consumer Services
1-800-237-7691
Monday - Friday 8 a.m. - 10 p.m. ET
Saturday 9 a.m. - 8 p.m. ET
Or write:
BISSELL Homecare, Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE
USE OF THIS PRODUCT. BISSELLS LIABILITY WILL NOT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER
ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION
OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION
FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
2008 BISSELL Homecare, Inc
Grand Rapids, Michigan
Some states do not allow limitations on how long an implied warranty lasts,
All rights reserved. Printed in China
so the above limitation may not apply to you.

NOTE: Please keep your original sales receipt,

it is your warranty.

12

www.bissell.com

ug120-4071_1770_908.indd 12

Part Number 120-4071

Rev 09/08
Visit our website at:
www.bissell.com

Scotchgard is a trademark of 3M

800.237.7691

10/14/08 1:06:11 PM