Step Shaft Design - Final

Step Shaft Design Analysis
Shigley Problem 18-20
1. Obtain step shaft assembly from the shared

drive, this assembly should include the step
shaft and two bearing supports with
constraints already provided.
2. To begin the analysis, load SolidWorks simulation by

navigating to the office products tab or loading it through the
Add-in menu in the tools drop down box.
Begin a New Simulation

3. Begin a new simulation by selecting the down arrow under
the study advisor tab and clicking on New Study. Since our
study is just going to deal with a static loading looking into
the failure of the shaft, simply select static and click the green check mark, this will begin the
study.
Setting Up Connections
4. Since we have an assembly, we must set up connections
rather than fixtures so SolidWorks knows how the parts
interact with each other. To do this, right click on the
connections menu in the simulation tree on the left side of
the screen. Select Bearing. This will

bring up the connector bearing
menu. It first asks for the surfaces
which the bearings will be
interacting with. To set this, first
select the face on the shaft that
lines up with the bearing holder
then select the inside surface of
the bearing holder for its second face. Deselect Allow Self-Alignment. Select okay, repeat for
the other side of the shaft.
Using Fixtures
5. Next place a fixed geometry fixture on the bottom of each of the bearing holders, this will tell
SolidWorks that these must remain in place throughout the simulation and insure that the part
does not fly downwards when
running. To do this, right click on the
fixtures menu in the simulation tree
and select fixed geometry. Fix the
two bottom surfaces of the bearing
supports in the x, y, and z direction.
Applying External Loads
6.
The problem statement calls for a 7kN force applied to the center of the shaft. To apply the load
right click on the external loads menu in the simulation tree and define a force. The acting face
will be the large face in the center of the shaft with the diameter of 45mm. SolidWorks default is
set to apply a force perpendicular to the face it is acting upon so when we select our face we get
a concentric force. This works fine if

you have a flat plate, however, with a
round shaft it wants to load it as if a
press fit has occurred and all of the
force is in the direction of the center of
the shaft. To define a direction,
highlight Select Direction in the force
menu. It now asks for a direction in
which to apply the load. Select the
centerline located on one side of the shaft to define a downward direction. Change the load to
7kN. The simulation menu and the model should look like the figure.
7. The problem also calls for a torque to be applied to the shaft. For the true simulation of the
shaft in question, it would difficult to load it as it would be in real life. In the book drawing there
are two key ways built into the shaft were the shaft would be connected and the torque be
transmitted. In order to simulate this situation, we will simply apply the torque to the faces in
question. To apply a torque right click on the external loads menu in the simulation tree, select
torque. SolidWorks asks for
three things, the face upon
which the torque is applied, the
direction the torque is applied
in, and the magnitude of the
torque. First select the smallest
diameter that is hanging out of
one side of the bearing. SolidWorks now asks for an axis, just select another step in the shaft.
Change the magnitude to 400N. Your model should look like the figure.
8. If the simulation was run now, the model would not solve since there is nothing to counter the
torque that was just applied. To solve this, repeat step 7 only select the large, major diameter
and select reverse direction when setting up the load. We select this diameter since in the book
it shows there is another keyway on this step. This should counter the torque set up in step 7
and bring the model back to static equilibrium.
Your model and simulation tree should look like the figures shown below.
Generating a Mesh
9. A mesh must now be generated. To do this, right click on the mesh menu and create a mesh. Set
the mesh size and then select okay. (Note: Because of the way SolidWorks runs its simulations
with connectors, it is necessary to have an adequate mesh size. If the mesh is too small the
simulation will fail because there are not enough data points in the interaction for it to run
successfully. If you are having trouble, set the mesh to a finer size. However, if the mesh is set
too fine, the time to run the simulation will be increased.
10. The model is now properly defined and a simulation can occur. In the ribbon, select run.

Step Shaft Design - Final

Uploaded by

Copyright:

Available Formats

Step Shaft Design - Final

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Step Shaft Design - Final

Uploaded by

Copyright:

Available Formats

Step Shaft Design Analysis

Shigley Problem 18-20

1. Obtain step shaft assembly from the shared

2. To begin the analysis, load SolidWorks simulation by

Begin a New Simulation

the screen. Select Bearing. This will

a concentric force. This works fine if

You might also like