WireShark Complete Users Guide

Wireshark User's Guide
31944 for Wireshark 1.2
Ulf Lamping,
Richard Sharpe, NS Computer Software and Services P/L
Ed Warnicke,
Wireshark User's Guide: 31944 for Wireshark
1.2
by Ulf Lamping, Richard Sharpe, and Ed Warnicke
Copyright © 2004-2008 Ulf Lamping Richard Sharpe Ed Warnicke
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 or any later
version published by the Free Software Foundation.
All logos and trademarks in this document are property of their respective owner.
Table of Contents
Preface ............................................................................................................................ ix
1. Foreword .............................................................................................................. ix
2. Who should read this document? .............................................................................. ix
3. Acknowledgements ................................................................................................ ix
4. About this document ............................................................................................... x
5. Where to get the latest copy of this document? ............................................................. x
6. Providing feedback about this document ..................................................................... x
1. Introduction ................................................................................................................... 1
1.1. What is Wireshark? .............................................................................................. 1
1.1.1. Some intended purposes .............................................................................. 1
1.1.2. Features ................................................................................................... 1
1.1.3. Live capture from many different network media ............................................. 2
1.1.4. Import files from many other capture programs ............................................... 2
1.1.5. Export files for many other capture programs .................................................. 2
1.1.6. Many protocol decoders .............................................................................. 2
1.1.7. Open Source Software ................................................................................ 3
1.1.8. What Wireshark is not ................................................................................ 3
1.2. System Requirements ............................................................................................ 3
1.2.1. General Remarks ....................................................................................... 3
1.2.2. Microsoft Windows .................................................................................... 3
1.2.3. Unix / Linux ............................................................................................. 4
1.3. Where to get Wireshark? ....................................................................................... 5
1.4. A brief history of Wireshark .................................................................................. 5
1.5. Development and maintenance of Wireshark ............................................................ 5
1.6. Reporting problems and getting help ........................................................................ 6
1.6.1. Website .................................................................................................... 6
1.6.2. Wiki ........................................................................................................ 6
1.6.3. FAQ ........................................................................................................ 6
1.6.4. Mailing Lists ............................................................................................. 7
1.6.5. Reporting Problems .................................................................................... 7
1.6.6. Reporting Crashes on UNIX/Linux platforms .................................................. 8
1.6.7. Reporting Crashes on Windows platforms ...................................................... 8
2. Building and Installing Wireshark ...................................................................................... 9
2.1. Introduction ......................................................................................................... 9
2.2. Obtaining the source and binary distributions ............................................................ 9
2.3. Before you build Wireshark under UNIX ................................................................ 10
2.4. Building Wireshark from source under UNIX .......................................................... 11
2.5. Installing the binaries under UNIX ......................................................................... 12
2.5.1. Installing from rpm's under Red Hat and alike ............................................... 12
2.5.2. Installing from deb's under Debian .............................................................. 13
2.5.3. Installing from portage under Gentoo Linux .................................................. 13
2.5.4. Installing from packages under FreeBSD ...................................................... 13
2.6. Troubleshooting during the install on Unix .............................................................. 13
2.7. Building from source under Windows ..................................................................... 14
2.8. Installing Wireshark under Windows ...................................................................... 14
2.8.1. Install Wireshark ...................................................................................... 14
2.8.2. Manual WinPcap Installation ...................................................................... 16
2.8.3. Update Wireshark ..................................................................................... 16
2.8.4. Update WinPcap ...................................................................................... 16
2.8.5. Uninstall Wireshark .................................................................................. 17
2.8.6. Uninstall WinPcap .................................................................................... 17
iii
3. User Interface ............................................................................................................... 18

3.1. Introduction ....................................................................................................... 18
3.2. Start Wireshark .................................................................................................. 18
3.3. The Main window .............................................................................................. 18
3.3.1. Main Window Navigation .......................................................................... 20
3.4. The Menu ......................................................................................................... 20
3.5. The "File" menu ................................................................................................. 21
3.6. The "Edit" menu ................................................................................................. 24
3.7. The "View" menu ............................................................................................... 26
3.8. The "Go" menu .................................................................................................. 28
3.9. The "Capture" menu ............................................................................................ 29
3.10. The "Analyze" menu ......................................................................................... 30
3.11. The "Statistics" menu ......................................................................................... 33
3.12. The "Telephony" menu ...................................................................................... 35
3.13. The "Tools" menu ............................................................................................. 36
3.14. The "Help" menu .............................................................................................. 36
3.15. The "Main" toolbar ........................................................................................... 38
3.16. The "Filter" toolbar ........................................................................................... 40
3.17. The "Packet List" pane ....................................................................................... 40
3.18. The "Packet Details" pane .................................................................................. 41
3.19. The "Packet Bytes" pane .................................................................................... 42
3.20. The Statusbar ................................................................................................... 42
4. Capturing Live Network Data .......................................................................................... 45
4.1. Introduction ....................................................................................................... 45
4.2. Prerequisites ...................................................................................................... 45
4.3. Start Capturing ................................................................................................... 46
4.4. The "Capture Interfaces" dialog box ....................................................................... 46
4.5. The "Capture Options" dialog box ......................................................................... 47
4.5.1. Capture frame .......................................................................................... 48
4.5.2. Capture File(s) frame ................................................................................ 50
4.5.3. Stop Capture... frame ................................................................................ 51
4.5.4. Display Options frame .............................................................................. 51
4.5.5. Name Resolution frame ............................................................................. 51
4.5.6. Buttons ................................................................................................... 51
4.6. The "Remote Capture Interfaces" dialog box ............................................................ 52
4.6.1. Remote Capture Interfaces ......................................................................... 53
4.6.2. Remote Capture ....................................................................................... 54
4.6.3. Remote Capture Settings ........................................................................... 54
4.7. The "Interface Details" dialog box ......................................................................... 56
4.8. Capture files and file modes ................................................................................. 56
4.9. Link-layer header type ......................................................................................... 58
4.10. Filtering while capturing .................................................................................... 58
4.10.1. Automatic Remote Traffic Filtering ............................................................ 60
4.11. While a Capture is running ... .............................................................................. 60
4.11.1. Stop the running capture .......................................................................... 61
4.11.2. Restart a running capture ......................................................................... 61
5. File Input / Output and Printing ....................................................................................... 62
5.1. Introduction ....................................................................................................... 62
5.2. Open capture files ............................................................................................... 62
5.2.1. The "Open Capture File" dialog box ............................................................ 62
5.2.2. Input File Formats .................................................................................... 65
5.3. Saving captured packets ....................................................................................... 66
5.3.1. The "Save Capture File As" dialog box ........................................................ 66
5.3.2. Output File Formats .................................................................................. 68
iv
5.4. Merging capture files .......................................................................................... 69

5.4.1. The "Merge with Capture File" dialog box .................................................... 69
5.5. File Sets ............................................................................................................ 70
5.5.1. The "List Files" dialog box ........................................................................ 71
5.6. Exporting data .................................................................................................... 72
5.6.1. The "Export as Plain Text File" dialog box ................................................... 72
5.6.2. The "Export as PostScript File" dialog box .................................................... 72
5.6.3. The "Export as CSV (Comma Separated Values) File" dialog box ...................... 73
5.6.4. The "Export as C Arrays (packet bytes) file" dialog box ................................... 73
5.6.5. The "Export as PSML File" dialog box ........................................................ 73
5.6.6. The "Export as PDML File" dialog box ........................................................ 74
5.6.7. The "Export selected packet bytes" dialog box ............................................... 75
5.6.8. The "Export Objects" dialog box ................................................................. 75
5.7. Printing packets .................................................................................................. 77
5.7.1. The "Print" dialog box .............................................................................. 77
5.8. The Packet Range frame ...................................................................................... 78
5.9. The Packet Format frame ..................................................................................... 78
6. Working with captured packets ........................................................................................ 80
6.1. Viewing packets you have captured ....................................................................... 80
6.2. Pop-up menus .................................................................................................... 81
6.2.1. Pop-up menu of the "Packet List" pane ........................................................ 81
6.2.2. Pop-up menu of the "Packet Details" pane .................................................... 83
6.3. Filtering packets while viewing ............................................................................. 85
6.4. Building display filter expressions ......................................................................... 86
6.4.1. Display filter fields ................................................................................... 86
6.4.2. Comparing values ..................................................................................... 86
6.4.3. Combining expressions .............................................................................. 88
6.4.4. A common mistake ................................................................................... 90
6.5. The "Filter Expression" dialog box ........................................................................ 90
6.6. Defining and saving filters ................................................................................... 91
6.7. Defining and saving filter macros .......................................................................... 93
6.8. Finding packets .................................................................................................. 93
6.8.1. The "Find Packet" dialog box ..................................................................... 93
6.8.2. The "Find Next" command ........................................................................ 94
6.8.3. The "Find Previous" command ................................................................... 94
6.9. Go to a specific packet ........................................................................................ 94
6.9.1. The "Go Back" command .......................................................................... 94
6.9.2. The "Go Forward" command ...................................................................... 94
6.9.3. The "Go to Packet" dialog box ................................................................... 94
6.9.4. The "Go to Corresponding Packet" command ................................................ 95
6.9.5. The "Go to First Packet" command .............................................................. 95
6.9.6. The "Go to Last Packet" command .............................................................. 95
6.10. Marking packets ............................................................................................... 95
6.11. Ignoring packets ............................................................................................... 95
6.12. Time display formats and time references .............................................................. 96
6.12.1. Packet time referencing ............................................................................ 97
7. Advanced Topics .......................................................................................................... 99
7.1. Introduction ....................................................................................................... 99
7.2. Following TCP streams ........................................................................................ 99
7.2.1. The "Follow TCP Stream" dialog box .......................................................... 99
7.3. Expert Infos ..................................................................................................... 100
7.3.1. Expert Info Entries ................................................................................. 101
7.3.2. "Expert Info Composite" dialog ................................................................. 102
7.3.3. "Colorized" Protocol Details Tree .............................................................. 102
v
7.3.4. "Expert" Packet List Column (optional) ...................................................... 103

7.4. Time Stamps .................................................................................................... 103
7.4.1. Wireshark internals ................................................................................. 103
7.4.2. Capture file formats ................................................................................ 104
7.4.3. Accuracy ............................................................................................... 104
7.5. Time Zones ...................................................................................................... 104
7.5.1. Set your computer's time correctly! ............................................................ 105
7.5.2. Wireshark and Time Zones ....................................................................... 106
7.6. Packet Reassembling ......................................................................................... 107
7.6.1. What is it? ............................................................................................ 107
7.6.2. How Wireshark handles it ........................................................................ 107
7.7. Name Resolution .............................................................................................. 108
7.7.1. Name Resolution drawbacks ..................................................................... 108
7.7.2. Ethernet name resolution (MAC layer) ....................................................... 109
7.7.3. IP name resolution (network layer) ............................................................ 109
7.7.4. IPX name resolution (network layer) .......................................................... 109
7.7.5. TCP/UDP port name resolution (transport layer) ........................................... 110
7.8. Checksums ....................................................................................................... 110
7.8.1. Wireshark checksum validation ................................................................. 110
7.8.2. Checksum offloading ............................................................................... 111
8. Statistics .................................................................................................................... 112
8.1. Introduction ..................................................................................................... 112
8.2. The "Summary" window .................................................................................... 112
8.3. The "Protocol Hierarchy" window ........................................................................ 113
8.4. Conversations ................................................................................................... 115
8.4.1. What is a Conversation? .......................................................................... 115
8.4.2. The "Conversations" window .................................................................... 115
8.4.3. The protocol specific "Conversation List" windows ....................................... 116
8.5. Endpoints ........................................................................................................ 116
8.5.1. What is an Endpoint? .............................................................................. 116
8.5.2. The "Endpoints" window ......................................................................... 117
8.5.3. The protocol specific "Endpoint List" windows ............................................ 118
8.6. The "IO Graphs" window ................................................................................... 118
8.7. Service Response Time ...................................................................................... 119
8.7.1. The "Service Response Time DCE-RPC" window ......................................... 120
8.8. WLAN Traffic Statistics ..................................................................................... 120
8.9. The protocol specific statistics windows ................................................................ 121
9. Telephony .................................................................................................................. 122
9.1. Introduction ..................................................................................................... 122
9.2. RTP Analysis ................................................................................................... 122
9.3. VoIP Calls ....................................................................................................... 122
9.4. LTE MAC Traffic Statistics ................................................................................ 123
9.5. LTE RLC Traffic Statistics ................................................................................. 123
9.6. The protocol specific statistics windows ................................................................ 124
10. Customizing Wireshark ............................................................................................... 125
10.1. Introduction .................................................................................................... 125
10.2. Start Wireshark from the command line ............................................................... 125
10.3. Packet colorization .......................................................................................... 131
10.4. Control Protocol dissection ................................................................................ 134
10.4.1. The "Enabled Protocols" dialog box ......................................................... 134
10.4.2. User Specified Decodes .......................................................................... 135
10.4.3. Show User Specified Decodes ................................................................. 136
10.5. Preferences ..................................................................................................... 137
10.5.1. Interface Options .................................................................................. 138
vi
10.6. Configuration Profiles ...................................................................................... 139

10.7. User Table ..................................................................................................... 141
10.8. Display Filter Macros ....................................................................................... 141
10.9. GeoIP Database Paths ...................................................................................... 141
10.10. Tektronix K12xx/15 RF5 protocols Table ........................................................... 142
10.11. PRES Users Context List ................................................................................ 142
10.12. SCCP users Table .......................................................................................... 142
10.13. SMI (MIB and PIB) Modules .......................................................................... 142
10.14. SMI (MIB and PIB) Paths ............................................................................... 142
10.15. SNMP Enterprise Specific Trap Types ............................................................... 143
10.16. SNMP users Table ......................................................................................... 143
10.17. User DLTs protocol table ................................................................................ 143
10.18. IKEv2 decryption table ................................................................................... 144
11. Lua Support in Wireshark ........................................................................................... 145
11.1. Introduction .................................................................................................... 145
11.2. Example of Dissector written in Lua ................................................................... 145
11.3. Example of Listener written in Lua ..................................................................... 146
11.4. Wireshark's Lua API Reference Manual ............................................................... 147
11.4.1. Saving capture files .............................................................................. 147
11.4.2. Obtaining dissection data ....................................................................... 149
11.4.3. GUI support ........................................................................................ 151
11.4.4. Post-dissection packet analysis ............................................................... 156
11.4.5. Obtaining packet information ................................................................. 157
11.4.6. Functions for writing dissectors .............................................................. 161
11.4.7. Adding information to the dissection tree .................................................. 172
11.4.8. Functions for handling packet data .......................................................... 174
11.4.9. Utility Functions .................................................................................. 180
A. Files and Folders ........................................................................................................ 184
A.1. Capture Files ................................................................................................... 184
A.1.1. Libpcap File Contents ............................................................................. 184
A.1.2. Not Saved in the Capture File .................................................................. 184
A.2. Configuration Files and Folders .......................................................................... 185
A.3. Windows folders .............................................................................................. 190
A.3.1. Windows profiles ................................................................................... 190
A.3.2. Windows Vista/XP/2000/NT roaming profiles ............................................. 191
A.3.3. Windows temporary folder ...................................................................... 191
B. Protocols and Protocol Fields ........................................................................................ 192
C. Wireshark Messages .................................................................................................... 193
C.1. Packet List Messages ........................................................................................ 193
C.1.1. [Malformed Packet] ................................................................................ 193
C.1.2. [Packet size limited during capture] ........................................................... 193
C.2. Packet Details Messages .................................................................................... 193
C.2.1. [Response in frame: 123] ......................................................................... 193
C.2.2. [Request in frame: 123] ........................................................................... 193
C.2.3. [Time from request: 0.123 seconds] ........................................................... 194
C.2.4. [Stream setup by PROTOCOL (frame 123)] ................................................ 194
D. Related command line tools .......................................................................................... 195
D.1. Introduction ..................................................................................................... 195
D.2. tshark: Terminal-based Wireshark ...................................................................... 195
D.3. tcpdump: Capturing with tcpdump for viewing with Wireshark ................................ 195
D.4. dumpcap: Capturing with dumpcap for viewing with Wireshark ............................... 195
D.5. capinfos: Print information about capture files ...................................................... 196
D.6. editcap: Edit capture files .................................................................................. 197
D.7. mergecap: Merging multiple capture files into one ................................................ 201
vii
D.8. text2pcap: Converting ASCII hexdumps to network captures ................................... 202

D.9. idl2wrs: Creating dissectors from CORBA IDL files .............................................. 205
D.9.1. What is it? ............................................................................................ 205
D.9.2. Why do this? ........................................................................................ 205
D.9.3. How to use idl2wrs ................................................................................ 205
D.9.4. TODO ................................................................................................. 207
D.9.5. Limitations ........................................................................................... 207
D.9.6. Notes ................................................................................................... 207
E. This Document's License (GPL) .................................................................................... 208
viii
Preface
1. Foreword
Wireshark is one of those programs that many network managers would love to be able to use, but they are
often prevented from getting what they would like from Wireshark because of the lack of documentation.
This document is part of an effort by the Wireshark team to improve the usability of Wireshark.
We hope that you find it useful, and look forward to your comments.
2. Who should read this document?

The intended audience of this book is anyone using Wireshark.
This book will explain all the basics and also some of the advanced features that Wireshark provides. As
Wireshark has become a very complex program since the early days, not every feature of Wireshark may
be explained in this book.
This book is not intended to explain network sniffing in general and it will not provide details about specific
network protocols. A lot of useful information regarding these topics can be found at the Wireshark Wiki
at http://wiki.wireshark.org
By reading this book, you will learn how to install Wireshark, how to use the basic elements of the graphical
user interface (such as the menu) and what's behind some of the advanced features that are not always
obvious at first sight. It will hopefully guide you around some common problems that frequently appear
for new (and sometimes even advanced) users of Wireshark.
3. Acknowledgements
The authors would like to thank the whole Wireshark team for their assistance. In particular, the authors
would like to thank:
• Gerald Combs, for initiating the Wireshark project and funding to do this documentation.
• Guy Harris, for many helpful hints and a great deal of patience in reviewing this document.
• Gilbert Ramirez, for general encouragement and helpful hints along the way.
The authors would also like to thank the following people for their helpful feedback on this document:
• Pat Eyler, for his suggestions on improving the example on generating a backtrace.
• Martin Regner, for his various suggestions and corrections.
• Graeme Hewson, for a lot of grammatical corrections.
The authors would like to acknowledge those man page and README authors for the Wireshark project
from who sections of this document borrow heavily:
• Scott Renfro from whose mergecap man page Section D.7, “mergecap: Merging multiple capture
files into one ” is derived.
ix
Preface
• Ashok Narayanan from whose text2pcap man page Section D.8, “text2pcap: Converting ASCII
hexdumps to network captures ” is derived.
• Frank Singleton from whose README.idl2wrs Section D.9, “idl2wrs: Creating dissectors from
CORBA IDL files ” is derived.
4. About this document

This book was originally developed by Richard Sharpe with funds provided from the Wireshark Fund. It
was updated by Ed Warnicke and more recently redesigned and updated by Ulf Lamping.
It is written in DocBook/XML.
You will find some specially marked parts in this book:
This is a warning!
You should pay attention to a warning, as otherwise data loss might occur.
This is a note!
A note will point you to common mistakes and things that might not be obvious.
This is a tip!
Tips will be helpful for your everyday work using Wireshark.
5. Where to get the latest copy of this

document?
The latest copy of this documentation can always be found at: http://www.wireshark.org/docs/.
6. Providing feedback about this document

Should you have any feedback about this document, please send it to the authors through wireshark-
dev[AT]wireshark.org.
x
Chapter 1. Introduction
1.1. What is Wireshark?
Wireshark is a network packet analyzer. A network packet analyzer will try to capture network packets
and tries to display that packet data as detailed as possible.
You could think of a network packet analyzer as a measuring device used to examine what's going on
inside a network cable, just like a voltmeter is used by an electrician to examine what's going on inside
an electric cable (but at a higher level, of course).
In the past, such tools were either very expensive, proprietary, or both. However, with the advent of
Wireshark, all that has changed.
Wireshark is perhaps one of the best open source packet analyzers available today.
1.1.1. Some intended purposes

Here are some examples people use Wireshark for:
• network administrators use it to troubleshoot network problems
• network security engineers use it to examine security problems
• developers use it to debug protocol implementations
• people use it to learn network protocol internals
Beside these examples, Wireshark can be helpful in many other situations too.
1.1.2. Features
The following are some of the many features Wireshark provides:
• Available for UNIX and Windows.
• Capture live packet data from a network interface.
• Display packets with very detailed protocol information.
• Open and Save packet data captured.
• Import and Export packet data from and to a lot of other capture programs.
• Filter packets on many criteria.
• Search for packets on many criteria.
• Colorize packet display based on filters.
• Create various statistics.
• ... and a lot more!
1
Introduction
However, to really appreciate its power, you have to start using it.
Figure 1.1, “ Wireshark captures packets and allows you to examine their content. ” shows Wireshark
having captured some packets and waiting for you to examine them.
Figure 1.1. Wireshark captures packets and allows you to examine their content.
1.1.3. Live capture from many different network media

Wireshark can capture traffic from many different network media types - and despite its name - including
wireless LAN as well. Which media types are supported, depends on many things like the operating
system you are using. An overview of the supported media types can be found at: http://wiki.wireshark.org/
CaptureSetup/NetworkMedia.
1.1.4. Import files from many other capture programs

Wireshark can open packets captured from a large number of other capture programs. For a list of input
formats see Section 5.2.2, “Input File Formats”.
1.1.5. Export files for many other capture programs

Wireshark can save packets captured in a large number of formats of other capture programs. For a list of
output formats see Section 5.3.2, “Output File Formats”.
1.1.6. Many protocol decoders

There are protocol decoders (or dissectors, as they are known in Wireshark) for a great many protocols:
see Appendix B, Protocols and Protocol Fields.
2
Introduction
1.1.7. Open Source Software

Wireshark is an open source software project, and is released under the GNU General Public License
(GPL). You can freely use Wireshark on any number of computers you like, without worrying about license
keys or fees or such. In addition, all source code is freely available under the GPL. Because of that, it is
very easy for people to add new protocols to Wireshark, either as plugins, or built into the source, and
they often do!
1.1.8. What Wireshark is not

Here are some things Wireshark does not provide:
• Wireshark isn't an intrusion detection system. It will not warn you when someone does strange things
on your network that he/she isn't allowed to do. However, if strange things happen, Wireshark might
help you figure out what is really going on.
• Wireshark will not manipulate things on the network, it will only "measure" things from it. Wireshark
doesn't send packets on the network or do other active things (except for name resolutions, but even
that can be disabled).
1.2. System Requirements

What you'll need to get Wireshark up and running ...
1.2.1. General Remarks

• The values below are the minimum requirements and only "rules of thumb" for use on a moderately
used network
• Working with a busy network can easily produce huge memory and disk space usage! For example:
Capturing on a fully saturated 100MBit/s Ethernet will produce ~ 750MBytes/min! Having a fast
processor, lots of memory and disk space is a good idea in that case.
• If Wireshark is running out of memory it crashes, see: http://wiki.wireshark.org/KnownBugs/

OutOfMemory for details and workarounds
• Wireshark won't benefit much from Multiprocessor/Hyperthread systems as time consuming tasks like
filtering packets are single threaded. No rule is without exception: during an "Update list of packets in
real time" capture, capturing traffic runs in one process and dissecting and displaying packets runs in
another process - which should benefit from two processors.
1.2.2. Microsoft Windows

• Windows XP Home, XP Pro, XP Tablet PC, XP Media Center, Server 2003, Vista, 2008, 7, or 2008 R2
• Any modern 32-bit x86 or 64-bit AMD64/x86-64 processor.
• 128MB available RAM. Larger capture files require more RAM.
• 75MB available disk space. Capture files require additional disk space.
• 800*600 (1280*1024 or higher recommended) resolution with at least 65536 (16bit) colors (256 colors
should work if Wireshark is installed with the "legacy GTK1" selection of the Wireshark 1.0.x releases)
3
Introduction
• A supported network card for capturing:
• Ethernet: Any card supported by Windows should work. See the wiki pages on Ethernet capture
and offloading for issues that may affect your environment.
• 802.11: See the Wireshark wiki page. Capturing raw 802.11 information may be difficult without
special equipment.
• Other media: See http://wiki.wireshark.org/CaptureSetup/NetworkMedia
Remarks:
• Many older Windows versions are no longer supported for three reasons: None of the developers use
those systems which makes support difficult. The libraries Wireshark depends on (GTK, WinPcap, …)
have dropped support for older releases. Microsoft has also dropped support for these systems.
• Windows 95, 98 and ME are no longer supported. The "old technology" releases of Windows lack
memory protection (specifically VirutalProtect) which we use to improve program safety and security.
The last known version to work was Ethereal 0.99.0 (which includes WinPcap 3.1). You can get it
from http://ethereal.com/download.html. According to this bug report, you may need to install Ethereal
0.10.0 on some systems. Microsoft retired support for Windows 98 and ME in 2006.
• Windows NT 4.0 no longer works with Wireshark. The last known version to work was Wireshark
0.99.4 (which includes WinPcap 3.1). You still can get it from http://www.wireshark.org/download/
win32/all-versions/wireshark-setup-0.99.4.exe. Microsoft retired support for Windows NT 4.0 in 2005.
• Windows CE and the embedded versions of Windows are not currently supported.
• Multiple monitor setups are supported but may behave a bit strangely.
1.2.3. Unix / Linux

Wireshark currently runs on most UNIX platforms. The system requirements should be comparable to the
Windows values listed above.
Binary packages are available for at least the following platforms:
• Apple Mac OS X
• Debian GNU/Linux
• FreeBSD
• Gentoo Linux
• HP-UX
• Mandriva Linux
• NetBSD
• OpenPKG
• Red Hat Fedora/Enterprise Linux
• rPath Linux
• Sun Solaris/i386
4
Introduction
• Sun Solaris/Sparc
• Canonical Ubuntu
If a binary package is not available for your platform, you should download the source and try to build it.
Please report your experiences to wireshark-dev[AT]wireshark.org .
1.3. Where to get Wireshark?

You can get the latest copy of the program from the Wireshark website: http://www.wireshark.org/
download.html. The website allows you to choose from among several mirrors for downloading.
A new Wireshark version will typically become available every 4-8 months.
If you want to be notified about new Wireshark releases, you should subscribe to the wireshark-announce
mailing list. You will find more details in Section 1.6.4, “Mailing Lists”.
1.4. A brief history of Wireshark

In late 1997, Gerald Combs needed a tool for tracking down networking problems and wanted to learn
more about networking, so he started writing Ethereal (the former name of the Wireshark project) as a
way to solve both problems.
Ethereal was initially released, after several pauses in development, in July 1998 as version 0.2.0. Within
days, patches, bug reports, and words of encouragement started arriving, so Ethereal was on its way to
success.
Not long after that, Gilbert Ramirez saw its potential and contributed a low-level dissector to it.
In October, 1998, Guy Harris of Network Appliance was looking for something better than tcpview, so he
started applying patches and contributing dissectors to Ethereal.
In late 1998, Richard Sharpe, who was giving TCP/IP courses, saw its potential on such courses, and started
looking at it to see if it supported the protocols he needed. While it didn't at that point, new protocols could
be easily added. So he started contributing dissectors and contributing patches.
The list of people who have contributed to the project has become very long since then, and almost all of
them started with a protocol that they needed that Wireshark or Ethereal did not already handle. So they
copied an existing dissector and contributed the code back to the team.
In 2006 the project moved house and re-emerged under a new name: Wireshark.
1.5. Development and maintenance of

Wireshark
Wireshark was initially developed by Gerald Combs. Ongoing development and maintenance of Wireshark
is handled by the Wireshark team, a loose group of individuals who fix bugs and provide new functionality.
There have also been a large number of people who have contributed protocol dissectors to Wireshark,
and it is expected that this will continue. You can find a list of the people who have contributed code to
Wireshark by checking the about dialog box of Wireshark, or at the authors page on the Wireshark web site.
Wireshark is an open source software project, and is released under the GNU General Public License
(GPL). All source code is freely available under the GPL. You are welcome to modify Wireshark to suit
5
Introduction
your own needs, and it would be appreciated if you contribute your improvements back to the Wireshark
team.
You gain three benefits by contributing your improvements back to the community:
• Other people who find your contributions useful will appreciate them, and you will know that you have
helped people in the same way that the developers of Wireshark have helped people.
• The developers of Wireshark might improve your changes even more, as there's always room for
improvement. Or they may implement some advanced things on top of your code, which can be useful
for yourself too.
• The maintainers and developers of Wireshark will maintain your code as well, fixing it when API
changes or other changes are made, and generally keeping it in tune with what is happening with
Wireshark. So if Wireshark is updated (which is done often), you can get a new Wireshark version
from the website and your changes will already be included without any effort for you.
The Wireshark source code and binary kits for some platforms are all available on the download page of
the Wireshark website: http://www.wireshark.org/download.html.
1.6. Reporting problems and getting help

If you have problems, or need help with Wireshark, there are several places that may be of interest to you
(well, besides this guide of course).
1.6.1. Website
You will find lots of useful information on the Wireshark homepage at http://www.wireshark.org.
1.6.2. Wiki
The Wireshark Wiki at http://wiki.wireshark.org provides a wide range of information related to Wireshark
and packet capturing in general. You will find a lot of information not part of this user's guide. For example,
there is an explanation how to capture on a switched network, an ongoing effort to build a protocol
reference and a lot more.
And best of all, if you would like to contribute your knowledge on a specific topic (maybe a network
protocol you know well), you can edit the wiki pages by simply using your web browser.
1.6.3. FAQ
The "Frequently Asked Questions" will list often asked questions and the corresponding answers.
Read the FAQ!

Before sending any mail to the mailing lists below, be sure to read the FAQ, as it will often
answer the question(s) you might have. This will save yourself and others a lot of time (keep
in mind that a lot of people are subscribed to the mailing lists).
You will find the FAQ inside Wireshark by clicking the menu item Help/Contents and selecting the FAQ
page in the dialog shown.
An online version is available at the Wireshark website: http://www.wireshark.org/faq.html. You might

prefer this online version, as it's typically more up to date and the HTML format is easier to use.
6
Introduction
1.6.4. Mailing Lists

There are several mailing lists of specific Wireshark topics available:
wireshark-announce This mailing list will inform you about new program releases, which usually
appear about every 4-8 weeks.
wireshark-users This list is for users of Wireshark. People post questions about building and
using Wireshark, others (hopefully) provide answers.
wireshark-dev This list is for Wireshark developers. If you want to start developing a
protocol dissector, join this list.
You can subscribe to each of these lists from the Wireshark web site: http://www.wireshark.org. Simply
select the mailing lists link on the left hand side of the site. The lists are archived at the Wireshark web
site as well.
Tip!
You can search in the list archives to see if someone asked the same question some time
before and maybe already got an answer. That way you don't have to wait until someone
answers your question.
1.6.5. Reporting Problems

Note!
Before reporting any problems, please make sure you have installed the latest version of
Wireshark.
When reporting problems with Wireshark, it is helpful if you supply the following information:
1. The version number of Wireshark and the dependent libraries linked with it, e.g. GTK+, etc. You can
obtain this with the command wireshark -v.
2. Information about the platform you run Wireshark on.
3. A detailed description of your problem.
4. If you get an error/warning message, copy the text of that message (and also a few lines before and
after it, if there are some), so others may find the place where things go wrong. Please don't give
something like: "I get a warning while doing x" as this won't give a good idea where to look at.
Don't send large files!

Do not send large files (>100KB) to the mailing lists, just place a note that further data
is available on request. Large files will only annoy a lot of people on the list who are not
interested in your specific problem. If required, you will be asked for further data by the
persons who really can help you.
Don't send confidential information!

If you send captured data to the mailing lists, be sure they don't contain any sensitive or
confidential information like passwords or such.
7
Introduction
1.6.6. Reporting Crashes on UNIX/Linux platforms

When reporting crashes with Wireshark, it is helpful if you supply the traceback information (besides the
information mentioned in "Reporting Problems").
You can obtain this traceback information with the following commands:
$ gdb `whereis wireshark | cut -f2 -d: | cut -d' ' -f2` core >& bt.txt
backtrace
^D
$
Note
Type the characters in the first line verbatim! Those are back-tics there!
Note
backtrace is a gdb command. You should enter it verbatim after the first line shown above,
but it will not be echoed. The ^D (Control-D, that is, press the Control key and the D key
together) will cause gdb to exit. This will leave you with a file called bt.txt in the current
directory. Include the file with your bug report.
Note
If you do not have gdb available, you will have to check out your operating system's
debugger.
You should mail the traceback to the wireshark-dev[AT]wireshark.org mailing list.
1.6.7. Reporting Crashes on Windows platforms

The Windows distributions don't contain the symbol files (.pdb), because they are very large. For this
reason it's not possible to create a meaningful backtrace file from it. You should report your crash just like
other problems, using the mechanism described above.
8
Chapter 2. Building and Installing
Wireshark
2.1. Introduction
As with all things, there must be a beginning, and so it is with Wireshark. To use Wireshark, you must:
• Obtain a binary package for your operating system, or
• Obtain the source and build Wireshark for your operating system.
Currently, several Linux distributions ship Wireshark, but they are commonly shipping an out-of-date
version. No other versions of UNIX ship Wireshark so far, and Microsoft does not ship it with any version
of Windows. For that reason, you will need to know where to get the latest version of Wireshark and how
to install it.
This chapter shows you how to obtain source and binary packages, and how to build Wireshark from
source, should you choose to do so.
The following are the general steps you would use:
1. Download the relevant package for your needs, e.g. source or binary distribution.
2. Build the source into a binary, if you have downloaded the source.
This may involve building and/or installing other necessary packages.
3. Install the binaries into their final destinations.
2.2. Obtaining the source and binary

distributions
You can obtain both source and binary distributions from the Wireshark web site: http://
www.wireshark.org. Simply select the download link, and then select either the source package or binary
package of your choice from the mirror site closest to you.
Download all required files!

In general, unless you have already downloaded Wireshark before, you will most likely need
to download several source packages if you are building Wireshark from source. This is
covered in more detail below.
Once you have downloaded the relevant files, you can go on to the next step.
Note!
While you will find a number of binary packages available on the Wireshark web site, you
might not find one for your platform, and they often tend to be several versions behind the
current released version, as they are contributed by people who have the platforms they are
built for.
9
Building and Installing Wireshark
For this reason, you might want to pull down the source distribution and build it, as the
process is relatively simple.
2.3. Before you build Wireshark under UNIX

Before you build Wireshark from sources, or install a binary package, you must ensure that you have the
following other packages installed:
• GTK+, The GIMP Tool Kit.
You will also need Glib. Both can be obtained from www.gtk.org
• libpcap, the packet capture software that Wireshark uses.
You can obtain libpcap from www.tcpdump.org
Depending on your system, you may be able to install these from binaries, e.g. RPMs, or you may need
to obtain them in source code form and build them.
If you have downloaded the source for GTK+, the instructions shown in Example 2.1, “Building GTK+
from source” may provide some help in building it:
Example 2.1. Building GTK+ from source
gzip -dc gtk+-1.2.10.tar.gz | tar xvf -

<much output removed>
cd gtk+-1.2.10
./configure
make
make install
Note!
You may need to change the version number of gtk+ in Example 2.1, “Building GTK+ from
source” to match the version of GTK+ you have downloaded. The directory you change to
will change if the version of GTK+ changes, and in all cases, tar xvf - will show you the
name of the directory you should change to.
Note!
If you use Linux, or have GNU tar installed, you can use tar zxvf gtk+-1.2.10.tar.gz. It is
also possible to use gunzip -c or gzcat rather than gzip -dc on many UNIX systems.
Note!
If you downloaded gtk+ or any other tar file using Windows, you may find your file called
gtk+-1_2_8_tar.gz.
You should consult the GTK+ web site if any errors occur in carrying out the instructions in Example 2.1,
“Building GTK+ from source”.
10
If you have downloaded the source to libpcap, the general instructions shown in Example 2.2, “Building
and installing libpcap” will assist in building it. Also, if your operating system does not support tcpdump,
you might also want to download it from the tcpdump web site and install it.
Example 2.2. Building and installing libpcap
gzip -dc libpcap-0.9.4.tar.Z | tar xvf -

cd libpcap-0.9.4
./configure
make
make install
Note!
The directory you should change to will depend on the version of libpcap you have
downloaded. In all cases, tar xvf - will show you the name of the directory that has been
unpacked.
Under Red Hat 6.x and beyond (and distributions based on it, like Mandrake) you can simply install each of
the packages you need from RPMs. Most Linux systems will install GTK+ and GLib in any case, however
you will probably need to install the devel versions of each of these packages. The commands shown in
Example 2.3, “ Installing required RPMs under Red Hat Linux 6.2 and beyond ” will install all the needed
RPMs if they are not already installed.
Example 2.3. Installing required RPMs under Red Hat Linux 6.2 and beyond
cd /mnt/cdrom/RedHat/RPMS
rpm -ivh glib-1.2.6-3.i386.rpm
rpm -ivh glib-devel-1.2.6-3.i386.rpm
rpm -ivh gtk+-1.2.6-7.i386.rpm
rpm -ivh gtk+-devel-1.2.6-7.i386.rpm
rpm -ivh libpcap-0.4-19.i386.rpm
Note
If you are using a version of Red Hat later than 6.2, the required RPMs have most likely
changed. Simply use the correct RPMs from your distribution.
Under Debian you can install Wireshark using aptitude. aptitude will handle any dependency issues for
you. Example 2.4, “Installing debs under Debian” shows how to do this.
Example 2.4. Installing debs under Debian
aptitude install wireshark-dev
2.4. Building Wireshark from source under

UNIX
Use the following general steps if you are building Wireshark from source under a UNIX operating system:
11
1. Unpack the source from its gzip'd tar file. If you are using Linux, or your version of UNIX uses GNU
tar, you can use the following command:
tar zxvf wireshark-1.2-tar.gz
For other versions of UNIX, you will want to use the following commands:
gzip -d wireshark-1.2-tar.gz
tar xvf wireshark-1.2-tar
Note!
The pipeline gzip -dc wireshark-1.2-tar.gz | tar xvf - will work here as well.
Note!
If you have downloaded the Wireshark tarball under Windows, you may find that your
browser has created a file with underscores rather than periods in its file name.
2. Change directory to the Wireshark source directory.
3. Configure your source so it will build correctly for your version of UNIX. You can do this with the
following command:
./configure
If this step fails, you will have to rectify the problems and rerun configure. Troubleshooting hints are
provided in Section 2.6, “Troubleshooting during the install on Unix”.
4. Build the sources into a binary, with the make command. For example:
make
5. Install the software in its final destination, using the command:
make install
Once you have installed Wireshark with make install above, you should be able to run it by entering
wireshark.
2.5. Installing the binaries under UNIX

In general, installing the binary under your version of UNIX will be specific to the installation methods
used with your version of UNIX. For example, under AIX, you would use smit to install the Wireshark
binary package, while under Tru64 UNIX (formerly Digital UNIX) you would use setld.
2.5.1. Installing from rpm's under Red Hat and alike

Use the following command to install the Wireshark RPM that you have downloaded from the Wireshark
web site:
12
rpm -ivh wireshark-1.2.i386.rpm
If the above step fails because of missing dependencies, install the dependencies first, and then retry the
step above. See Example 2.3, “ Installing required RPMs under Red Hat Linux 6.2 and beyond ” for
information on what RPMs you will need to have installed.
2.5.2. Installing from deb's under Debian

If you can just install from the repository then use:
aptitude install wireshark
aptitude should take care of all of the dependency issues for you.
Use the following command to install downloaded Wireshark deb's under Debian:
dpkg -i wireshark-common_1.2.0-1_i386.deb wireshark_1.2.0-1_i386.deb
dpkg doesn't take care of all dependencies, but reports what's missing.
2.5.3. Installing from portage under Gentoo Linux

Use the following command to install Wireshark under Gentoo Linux with all of the extra features:
USE="adns gtk ipv6 portaudio snmp ssl kerberos threads selinux" emerge wireshark
2.5.4. Installing from packages under FreeBSD

Use the following command to install Wireshark under FreeBSD:
pkg_add -r wireshark
pkg_add should take care of all of the dependency issues for you.
2.6. Troubleshooting during the install on Unix

A number of errors can occur during the installation process. Some hints on solving these are provided here.
If the configure stage fails, you will need to find out why. You can check the file config.log in the
source directory to find out what failed. The last few lines of this file should help in determining the
problem.
The standard problems are that you do not have GTK+ on your system, or you do not have a recent enough
version of GTK+. The configure will also fail if you do not have libpcap (at least the required include
files) on your system.
Another common problem is for the final compile and link stage to terminate with a complaint of: Output
too long. This is likely to be caused by an antiquated sed (such as the one shipped with Solaris). Since sed
13
is used by the libtool script to construct the final link command, this leads to mysterious problems. This
can be resolved by downloading a recent version of sed from http://directory.fsf.org/project/sed/.
If you cannot determine what the problems are, send an email to the wireshark-dev mailing list explaining
your problem, and including the output from config.log and anything else you think is relevant, like
a trace of the make stage.
2.7. Building from source under Windows

It is recommended to use the binary installer for Windows, until you want to start developing Wireshark
on the Windows platform.
For further information how to build Wireshark for Windows from the sources, have a look at the
Developer's Guide on the Documentation Page.
You may also want to have a look at the Development Wiki: http://wiki.wireshark.org/Development for
the latest available development documentation.
2.8. Installing Wireshark under Windows

In this section we explore installing Wireshark under Windows from the binary packages.
2.8.1. Install Wireshark

You may acquire a binary installer of Wireshark named something like: wireshark-
winxx-1.2.x.exe. The Wireshark installer includes WinPcap, so you don't need to download and
install two separate packages.
Simply download the Wireshark installer from: http://www.wireshark.org/download.html and execute it.
Beside the usual installer options like where to install the program, there are several optional components.
Tip: Just keep the defaults!

If you are unsure which settings to select, just keep the defaults.
2.8.1.1. "Choose Components" page

Wireshark
• Wireshark GTK - Wireshark is a GUI network protocol analyzer.
TShark - TShark is a command-line based network protocol analyzer.
Plugins / Extensions (for the Wireshark and TShark dissection engines):
• Dissector Plugins - Plugins with some extended dissections.
• Tree Statistics Plugins - Plugins with some extended statistics.
• Mate - Meta Analysis and Tracing Engine (experimental) - user configurable extension(s) of the
display filter engine, see http://wiki.wireshark.org/Mate for details.
• SNMP MIBs - SNMP MIBs for a more detailed SNMP dissection.
14
Tools (additional command line tools to work with capture files):
• Editcap - Editcap is a program that reads a capture file and writes some or all of the packets into
another capture file.
• Text2Pcap - Text2pcap is a program that reads in an ASCII hex dump and writes the data into a
libpcap-style capture file.
• Mergecap - Mergecap is a program that combines multiple saved capture files into a single output file.
• Capinfos - Capinfos is a program that provides information on capture files.
• Rawshark - Rawshark is a raw packet filter.
User's Guide - Local installation of the User's Guide. The Help buttons on most dialogs will require an
internet connection to show help pages if the User's Guide is not installed locally.
2.8.1.2. "Additional Tasks" page

• Start Menu Shortcuts - add some start menu shortcuts.
• Desktop Icon - add a Wireshark icon to the desktop.
• Quick Launch Icon - add a Wireshark icon to the Explorer quick launch toolbar.
• Associate file extensions to Wireshark - Associate standard network trace files to Wireshark.
2.8.1.3. "Install WinPcap?" page

The Wireshark installer contains the latest released WinPcap installer.
If you don't have WinPcap installed, you won't be able to capture live network traffic, but you will still
be able to open saved capture files.
• Currently installed WinPcap version - the Wireshark installer detects the currently installed
WinPcap version.
• Install WinPcap x.x - if the currently installed version is older than the one which comes with the
Wireshark installer (or WinPcap is not installed at all), this will be selected by default.
• Start WinPcap service "NPF" at startup - so users without administrative privileges can capture.
More WinPcap info:
• Wireshark related: http://wiki.wireshark.org/WinPcap
• General WinPcap info: http://www.winpcap.org
2.8.1.4. Command line options

You can simply start the Wireshark installer without any command line parameters, it will show you the
usual interactive installer.
For special cases, there are some command line parameters available:
• /NCRC disables the CRC check
15
• /S runs the installer or uninstaller silently with default values. Please note: The silent installer won't
install WinPCap!
• /desktopicon installation of the desktop icon, =yes - force installation, =no - don't install, otherwise
use defaults / user settings. This option can be useful for a silent installer.
• /quicklaunchicon installation of the quick launch icon, =yes - force installation, =no - don't install,
otherwise use defaults / user settings.
• /D sets the default installation directory ($INSTDIR), overriding InstallDir and InstallDirRegKey. It
must be the last parameter used in the command line and must not contain any quotes, even if the path
contains spaces.
Example:
wireshark-win32-1.2.0.exe /NCRC /S /desktopicon=yes

/quicklaunchicon=no /D=C:\Program Files\Foo
2.8.2. Manual WinPcap Installation

Note!
As mentioned above, the Wireshark installer takes care of the installation of WinPcap,
so usually you don't have to worry about WinPcap at all!
The following is only necessary if you want to try a different version than the one included in the Wireshark
installer, e.g. because a new WinPcap (beta) version was released.
Additional WinPcap versions (including newer alpha or beta releases) can be downloaded from the
following locations:
• The main WinPcap site: http://www.winpcap.org
• The Wiretapped.net mirror: http://www.mirrors.wiretapped.net/security/packet-capture/winpcap
At the download page you will find a single installer exe called something like "auto-installer", which can
be installed under various Windows systems, including NT4.0/2000/XP/2003/Vista/7/2008.
2.8.3. Update Wireshark

From time to time you may want to update your installed Wireshark to a more recent version. If you join
Wireshark's announce mailing list, you will be informed about new Wireshark versions, see Section 1.6.4,
“Mailing Lists” for details how to subscribe to this list.
New versions of Wireshark usually become available every 4 to 8 months. Updating Wireshark is done the
same way as installing it, you simply download and start the installer exe. A reboot is usually not required
and all your personal settings remain unchanged.
2.8.4. Update WinPcap

New versions of WinPcap are less frequently available, maybe only once in a year. You will find WinPcap
update instructions where you can download new WinPcap versions. Usually you have to reboot the
machine after installing a new WinPcap version.
16
Warning!
If you have an older version of WinPcap installed, you must uninstall it before installing the
current version. Recent versions of the WinPcap installer will take care of this.
2.8.5. Uninstall Wireshark

You can uninstall Wireshark the usual way, using the "Add or Remove Programs" option inside the Control
Panel. Select the "Wireshark" entry to start the uninstallation procedure.
The Wireshark uninstaller will provide several options as to which things are to be uninstalled; the default
is to remove the core components but keep the personal settings, WinPcap and alike.
WinPcap won't be uninstalled by default, as other programs than Wireshark may use it as well.
2.8.6. Uninstall WinPcap

You can uninstall WinPcap independently of Wireshark, using the "WinPcap" entry in the "Add or Remove
Programs" of the Control Panel.
Note!
After uninstallation of WinPcap you can't capture anything with Wireshark.
It might be a good idea to reboot Windows afterwards.
17
Chapter 3. User Interface
3.1. Introduction
By now you have installed Wireshark and are most likely keen to get started capturing your first packets.
In the next chapters we will explore:
• How the Wireshark user interface works
• How to capture packets in Wireshark
• How to view packets in Wireshark
• How to filter packets in Wireshark
• ... and many other things!
3.2. Start Wireshark

You can start Wireshark from your shell or window manager.
Tip!
When starting Wireshark it's possible to specify optional settings using the command line.
See Section 10.2, “Start Wireshark from the command line” for details.
Note!
In the following chapters, a lot of screenshots from Wireshark will be shown. As Wireshark
runs on many different platforms with many different window managers, different styles
applied and there are different versions of the underlying GUI toolkit used, your screen
might look different from the provided screenshots. But as there are no real differences in
functionality, these screenshots should still be well understandable.
3.3. The Main window

Let's look at Wireshark's user interface. Figure 3.1, “The Main window” shows Wireshark as you would
usually see it after some packets are captured or loaded (how to do this will be described later).
18
User Interface
Figure 3.1. The Main window
Wireshark's main window consists of parts that are commonly known from many other GUI programs.
1. The menu (see Section 3.4, “The Menu”) is used to start actions.
2. The main toolbar (see Section 3.15, “The "Main" toolbar”) provides quick access to frequently used
items from the menu.
3. The filter toolbar (see Section 3.16, “The "Filter" toolbar”) provides a way to directly manipulate the
currently used display filter (see Section 6.3, “Filtering packets while viewing”).
4. The packet list pane (see Section 3.17, “The "Packet List" pane”) displays a summary of each packet
captured. By clicking on packets in this pane you control what is displayed in the other two panes.
5. The packet details pane (see Section 3.18, “The "Packet Details" pane”) displays the packet selected
in the packet list pane in more detail.
6. The packet bytes pane (see Section 3.19, “The "Packet Bytes" pane”) displays the data from the packet
selected in the packet list pane, and highlights the field selected in the packet details pane.
7. The statusbar (see Section 3.20, “The Statusbar”) shows some detailed information about the current
program state and the captured data.
Tip!
The layout of the main window can be customized by changing preference settings. See
Section 10.5, “Preferences” for details!
19
User Interface
3.3.1. Main Window Navigation

Packet list and detail navigation can be done entirely from the keyboard. Table 3.1, “Keyboard Navigation”
shows a list of keystrokes that will let you quickly move around a capture file. See Table 3.5, “Go menu
items” for additional navigation keystrokes.
Table 3.1. Keyboard Navigation

Accelerator Description
Tab, Shift+Tab Move between screen elements, e.g. from the toolbars to the packet list to the packet
detail.
Down Move to the next packet or detail item.
Up Move to the previous packet or detail item.
Ctrl+Down, F8 Move to the next packet, even if the packet list isn't focused.
Ctrl+Up, F7 Move to the previous packet, even if the packet list isn't focused.
Left In the packet detail, closes the selected tree item. If it's already closed, jumps to the
parent node.
Right In the packet detail, opens the selected tree item.
Shift+Right In the packet detail, opens the selected tree item and all of its subtrees.
Ctrl+Right In the packet detail, opens all tree items.
Ctrl+Left In the packet detail, closes all tree items.
Backspace In the packet detail, jumps to the parent node.
Return, Enter In the packet detail, toggles the selected tree item.
Additionally, typing anywhere in the main window will start filling in a display filter.
3.4. The Menu

The Wireshark menu sits on top of the Wireshark window. An example is shown in Figure 3.2, “The
Menu”.
Note!
Menu items will be greyed out if the corresponding feature isn't available. For example, you
cannot save a capture file if you didn't capture or load any data before.
Figure 3.2. The Menu
It contains the following items:
File This menu contains items to open and merge capture files, save / print / export capture
files in whole or in part, and to quit from Wireshark. See Section 3.5, “The "File" menu”.
Edit This menu contains items to find a packet, time reference or mark one or more packets,
handle configuration profiles, and set your preferences; (cut, copy, and paste are not
presently implemented). See Section 3.6, “The "Edit" menu”.
20
User Interface
View This menu controls the display of the captured data, including colorization of packets,
zooming the font, showing a packet in a separate window, expanding and collapsing trees
in packet details, .... See Section 3.7, “The "View" menu”.
Go This menu contains items to go to a specific packet. See Section 3.8, “The "Go" menu”.
Capture This menu allows you to start and stop captures and to edit capture filters. See Section 3.9,
“The "Capture" menu”.
Analyze This menu contains items to manipulate display filters, enable or disable the dissection of
protocols, configure user specified decodes and follow a TCP stream. See Section 3.10,
“The "Analyze" menu”.
Statistics This menu contains items to display various statistic windows, including a summary of
the packets that have been captured, display protocol hierarchy statistics and much more.
See Section 3.11, “The "Statistics" menu”.
Telephony This menu contains items to display various telephony related statistic windows,
including a media analysis, flow diagrams, display protocol hierarchy statistics and much
more. See Section 3.12, “The "Telephony" menu”.
Tools This menu contains various tools available in Wireshark, such as creating Firewall ACL
Rules. See Section 3.13, “The "Tools" menu”.
Help This menu contains items to help the user, e.g. access to some basic help, a list of the
supported protocols, manual pages, online access to some of the webpages, and the usual
about dialog. See Section 3.14, “The "Help" menu”.
Each of these menu items is described in more detail in the sections that follow.
Tip!
You can access menu items directly or by pressing the corresponding accelerator keys which
are shown at the right side of the menu. For example, you can press the Control (or Strg in
German) and the K keys together to open the capture dialog.
3.5. The "File" menu

The Wireshark file menu contains the fields shown in Table 3.2, “File menu items”.
21
User Interface
Figure 3.3. The "File" Menu
22
Files pops up the Wireshark List File Set dialog box (which is discussed
further in Section 5.5, “File Sets”).
File Set > Next If the currently loaded file is part of a file set, jump to the next file
File inUser
the Interface
set. If it isn't part of a file set or just the last file in that set,
this item is greyed out.
File Set > If the currently loaded file is part of a file set, jump to the previous
Table 3.2.
Previous FileFile menu items file in the set. If it isn't part of a file set or just the first file in that
set, this item is greyed out.
------
Export > as This menu item allows you to export all (or some) of the packets in
"Plain Text" the capture file to a plain ASCII text file. It pops up the Wireshark
file... Export dialog box (which is discussed further in Section 5.6.1,
“The "Export as Plain Text File" dialog box”).
Export > as This menu item allows you to export all (or some) of the packets
"PostScript" in the capture file to a PostScript file. It pops up the Wireshark
file... Export dialog box (which is discussed further in Section 5.6.2,
“The "Export as PostScript File" dialog box”).
Export > as This menu item allows you to export all (or some) of the packet
"CSV"(Comma summaries in the capture file to a .csv file (e.g. used by spreadsheet
Separated programs). It pops up the Wireshark Export dialog box (which is
Values packet discussed further in Section 5.6.3, “The "Export as CSV (Comma
summary) file... Separated Values) File" dialog box”).
Export > as "C This menu item allows you to export all (or some) of the packet
Arrays" (packet bytes in the capture file to a .c file so you can import the stream data
bytes) file... into your own C program. It pops up the Wireshark Export dialog
box (which is discussed further in Section 5.6.4, “The "Export as
C Arrays (packet bytes) file" dialog box”).
------
Export > as This menu item allows you to export all (or some) of the packets
"PSML" file... in the capture file to a PSML (packet summary markup language)
XML file. It pops up the Wireshark Export dialog box (which is
discussed further in Section 5.6.5, “The "Export as PSML File"
dialog box”).
Export > as This menu item allows you to export all (or some) of the packets in
"PDML" file... the capture file to a PDML (packet details markup language) XML
file. It pops up the Wireshark Export dialog box (which is discussed
further in Section 5.6.6, “The "Export as PDML File" dialog box”).
------
Export > Ctrl+H This menu item allows you to export the currently selected bytes
Selected Packet in the packet bytes pane to a binary file. It pops up the Wireshark
Bytes... Export dialog box (which is discussed further in Section 5.6.7,
“The "Export selected packet bytes" dialog box”)
Objects > This menu item allows you to export all or some of the captured
HTTP HTTP objects into local files. It pops up the Wireshark HTTP
object list (which is discussed further in Section 5.6.8, “The
"Export Objects" dialog box”)
------
Print... Ctrl+P This menu item allows you to print all (or some) of the packets in
the capture file. It pops up the Wireshark Print dialog box (which
is discussed further in Section 5.7, “Printing packets”).
------
Quit Ctrl+Q This menu item allows you to quit from Wireshark. Wireshark will
ask to save your capture file if you haven't previously saved it (this
can be disabled by a preference setting).
23
User Interface
3.6. The "Edit" menu

The Wireshark Edit menu contains the fields shown in Table 3.3, “Edit menu items”.
Figure 3.4. The "Edit" Menu
24
Copy > Shift+Ctrl+F This menu item will copy the fieldname of the selected item in the
Fieldname detail view to the clipboard.
Copy > Value Shift+Ctrl+V This
Usermenu item will copy the value of the selected item in the detail
Interface
view to the clipboard.
Copy > As Shift+Ctrl+C This menu item will use the selected item in the detail view to
Filter 3.3. Edit menu items
Table create a display filter. This display filter is then copied to the
clipboard.
------
Find Packet... Ctrl+F This menu item brings up a dialog box that allows you to find a
packet by many criteria. There is further information on finding
packets in Section 6.8, “Finding packets”.
Find Next Ctrl+N This menu item tries to find the next packet matching the settings
from "Find Packet...".
Find Previous Ctrl+B This menu item tries to find the previous packet matching the
settings from "Find Packet...".
------
Mark Packet Ctrl+M This menu item "marks" the currently selected packet. See
(toggle) Section 6.10, “Marking packets” for details.
Find Next Shift+Ctrl+N Find the next marked packet.
Mark
Find Previous Shift+Ctrl+B Find the previous marked packet.
Mark
Mark All This menu item "marks" all displayed packets.
Displayed
Packets
Unmark All This menu item "unmarks" all marked packets.
Packets
------
Ignore Packet Ctrl+X This menu item marks the currently selected packet as ignored. See
(toggle) Section 6.11, “Ignoring packets” for details.
Ignore All Shift-Ctrl-Alt-X This menu item marks all displayed packets as ignored.
Displayed
Packets
Un-Ignore All Shift-Ctrl-X This menu item unmarks all ignored packets.
Packets
------
Set Time Ctrl+T This menu item set a time reference on the currently selected
Reference packet. See Section 6.12.1, “Packet time referencing” for more
(toggle) information about the time referenced packets.
Find Next This menu item tries to find the next time referenced packet.
Reference
Find Previous This menu item tries to find the previous time referenced packet.
Reference
------
Configuration Shift-Ctrl-A This menu item brings up a dialog box for handling configuration
Profiles... profiles. More detail is provided in Section 10.6, “Configuration
Profiles”.
Preferences... Shift+Ctrl+P This menu item brings up a dialog box that allows you to set
preferences for many parameters that control Wireshark. You can
also save your preferences so Wireshark will use them the next time
you start it. More detail is provided in Section 10.5, “Preferences”.
25
User Interface
3.7. The "View" menu

The Wireshark View menu contains the fields shown in Table 3.4, “View menu items”.
Figure 3.5. The "View" Menu
26
Note!
Enabling colorization will slow down the display of
new packets while capturing / loading capture files.
User Interface
Auto Scroll in This item allows you to specify that Wireshark should scroll the
Live Capture packet list pane as new packets come in, so you are always looking
Table 3.4. View menu items at the last packet. If you do not specify this, Wireshark simply adds
new packets onto the end of the list, but does not scroll the packet
list pane.
------
Zoom In Ctrl++ Zoom into the packet data (increase the font size).
Zoom Out Ctrl+- Zoom out of the packet data (decrease the font size).
Normal Size Ctrl+= Set zoom level back to 100% (set font size back to normal).
Resize All Resize all column widths so the content will fit into it.
Columns
Note!
Resizing may take a significant amount of time,
especially if a large capture file is loaded.
------
Expand This menu item expands the currently selected subtree in the packet
Subtrees details tree.
Expand All Wireshark keeps a list of all the protocol subtrees that are
expanded, and uses it to ensure that the correct subtrees are
expanded when you display a packet. This menu item expands all
subtrees in all packets in the capture.
Collapse All This menu item collapses the tree view of all packets in the capture
list.
------
Colorize This menu item brings up a submenu that allows you to color
Conversation packets in the packet list pane based on the addresses of the
currently selected packet. This makes it easy to distinguish
packets belonging to different conversations. Section 10.3, “Packet
colorization”.
Colorize These menu items enable one of the ten temporary color filters
Conversation > based on the currently selected conversation.
Color 1-10
Colorize This menu item clears all temporary coloring rules.
Conversation >
Reset coloring
Colorize This menu item opens a dialog window in which a new permanent
Conversation > coloring rule can be created based on the currently selected
New Coloring conversation.
Rule...
Coloring This menu item brings up a dialog box that allows you to color
Rules... packets in the packet list pane according to filter expressions you
choose. It can be very useful for spotting certain types of packets,
see Section 10.3, “Packet colorization”.
------
Show Packet in This menu item brings up the selected packet in a separate window.
New Window The separate window shows only the tree view and byte view
panes.
Reload Ctrl-R This menu item allows you to reload the current capture file.
27
User Interface
3.8. The "Go" menu

The Wireshark Go menu contains the fields shown in Table 3.5, “Go menu items”.
Figure 3.6. The "Go" Menu
28
User Interface
Table 3.5. Go menu items
Menu Item Accelerator Description

Back Alt+Left Jump to the recently visited packet in the packet history, much like
the page history in a web browser.
Forward Alt+Right Jump to the next visited packet in the packet history, much like the
page history in a web browser.
Go to Packet... Ctrl-G Bring up a dialog box that allows you to specify a packet number,
and then goes to that packet. See Section 6.9, “Go to a specific
packet” for details.
Go to Go to the corresponding packet of the currently selected protocol
Corresponding field. If the selected field doesn't correspond to a packet, this item
Packet is greyed out.
------
Previous Ctrl+Up Move to the previous packet in the list. This can be used to move
Packet to the previous packet even if the packet list doesn't have keyboard
focus.
Next Packet Ctrl+Down Move to the next packet in the list. This can be used to move to the
previous packet even if the packet list doesn't have keyboard focus.
First Packet Ctrl+Home Jump to the first packet of the capture file.
Last Packet Ctrl+End Jump to the last packet of the capture file.
3.9. The "Capture" menu

The Wireshark Capture menu contains the fields shown in Table 3.6, “Capture menu items”.
29
User Interface
Figure 3.7. The "Capture" Menu
Table 3.6. Capture menu items

Interfaces... This menu item brings up a dialog box that shows what's going
on at the network interfaces Wireshark knows of, see Section 4.4,
“The "Capture Interfaces" dialog box”) .
Options... Ctrl+K This menu item brings up the Capture Options dialog box
(discussed further in Section 4.5, “The "Capture Options" dialog
box”) and allows you to start capturing packets.
Start Immediately start capturing packets with the same settings than the
last time.
Stop Ctrl+E This menu item stops the currently running capture, see
Section 4.11.1, “Stop the running capture”) .
Restart This menu item stops the currently running capture and starts again
with the same options, this is just for convenience.
Capture This menu item brings up a dialog box that allows you to create and
Filters... edit capture filters. You can name filters, and you can save them for
future use. More detail on this subject is provided in Section 6.6,
“Defining and saving filters”
3.10. The "Analyze" menu

The Wireshark Analyze menu contains the fields shown in Table 3.7, “Analyze menu items”.
30
User Interface
Figure 3.8. The "Analyze" Menu
31
User Interface
Table 3.7. Analyze menu items

Display This menu item brings up a dialog box that allows you to create and
Filters... edit display filters. You can name filters, and you can save them for
future use. More detail on this subject is provided in Section 6.6,
“Defining and saving filters”
Display Filter This menu item brings up a dialog box that allows you to create and
Macros... edit display filter macros. You can name filter macros, and you can
save them for future use. More detail on this subject is provided in
Section 6.7, “Defining and saving filter macros”
Apply as Filter These menu items will change the current display filter and apply
> ... the changed filter immediately. Depending on the chosen menu
item, the current display filter string will be replaced or appended
to by the selected protocol field in the packet details pane.
Prepare a Filter These menu items will change the current display filter but won't
> ... apply the changed filter. Depending on the chosen menu item, the
current display filter string will be replaced or appended to by the
selected protocol field in the packet details pane.
------
Enabled Shift+Ctrl+R This menu item allows the user to enable/disable protocol
Protocols... dissectors, see Section 10.4.1, “The "Enabled Protocols" dialog
box”
Decode As... This menu item allows the user to force Wireshark to decode
certain packets as a particular protocol, see Section 10.4.2, “User
Specified Decodes”
User Specified This menu item allows the user to force Wireshark to decode
Decodes... certain packets as a particular protocol, see Section 10.4.3, “Show
User Specified Decodes”
------
Follow TCP This menu item brings up a separate window and displays all the
Stream TCP segments captured that are on the same TCP connection as a
selected packet, see Section 7.2, “Following TCP streams”
Follow UDP Same functionality as "Follow TCP Stream" but for UDP streams.
Stream
Follow SSL Same functionality as "Follow TCP Stream" but for SSL streams.
Stream XXX - how to provide the SSL keys?
Expert Info Open a dialog showing some expert information about the captured
packets in a log style display. The amount of information will
depend on the protocol and varies from very detailed to none
existing. This is currently a work in progress. XXX - add a new
section about this and link from here
Expert Info Same information as in "Expert Info" but trying to group items
Composite together for faster analysis.
Conversation In this menu you will find conversation filter for various protocols.
Filter > ...
32
User Interface
3.11. The "Statistics" menu

The Wireshark Statistics menu contains the fields shown in Table 3.8, “Statistics menu items”.
Figure 3.9. The "Statistics" Menu
All menu items will bring up a new window showing specific statistical information.
33
User Interface
Table 3.8. Statistics menu items

Summary Show information about the data captured, see Section 8.2, “The
"Summary" window”.
Protocol Display a hierarchical tree of protocol statistics, see Section 8.3,
Hierarchy “The "Protocol Hierarchy" window”.
Conversations Display a list of conversations (traffic between two endpoints), see
Section 8.4.2, “The "Conversations" window”.
Endpoints Display a list of endpoints (traffic to/from an address), see
Section 8.5.2, “The "Endpoints" window”.
Packet See Section 8.9, “The protocol specific statistics windows”
Lengths...
IO Graphs Display user specified graphs (e.g. the number of packets in the
course of time), see Section 8.6, “The "IO Graphs" window”.
------
Conversation Display a list of conversations, obsoleted by the combined window
List of Conversations above, see Section 8.4.3, “The protocol specific
"Conversation List" windows”.
Endpoint List Display a list of endpoints, obsoleted by the combined window
of Endpoints above, see Section 8.5.3, “The protocol specific
"Endpoint List" windows”.
Service Display the time between a request and the corresponding
Response Time response, see Section 8.7, “Service Response Time”.
------
BOOTP- See Section 8.9, “The protocol specific statistics windows”
DHCP...
Compare... See Section 8.9, “The protocol specific statistics windows”
Flow Graph... See Section 8.9, “The protocol specific statistics windows”
HTTP HTTP request/response statistics, see Section 8.9, “The protocol
specific statistics windows”
IP Addresses... See Section 8.9, “The protocol specific statistics windows”
IP See Section 8.9, “The protocol specific statistics windows”
Destinations...
IP Protocol See Section 8.9, “The protocol specific statistics windows”
Types...
ISUP Messages See Section 8.9, “The protocol specific statistics windows”
ONC-RPC See Section 8.9, “The protocol specific statistics windows”
Programs
TCP Stream See Section 8.9, “The protocol specific statistics windows”
Graph
UDP Multicast See Section 8.9, “The protocol specific statistics windows”
Streams
WLAN Traffic See Section 8.8, “WLAN Traffic Statistics”
34
User Interface
3.12. The "Telephony" menu

The Wireshark Telephony menu contains the fields shown in Table 3.9, “Telephony menu items”.
Figure 3.10. The "Telephony" Menu
All menu items will bring up a new window showing specific telephony related statistical information.
35
User Interface
Table 3.9. Telephony menu items

ANSI See Section 9.6, “The protocol specific statistics windows”
Fax T38 See Section 9.6, “The protocol specific statistics windows”
Analysis...
GSM See Section 9.6, “The protocol specific statistics windows”
H.225... See Section 9.6, “The protocol specific statistics windows”
IAX2 See Section 9.6, “The protocol specific statistics windows”
ISUP See Section 9.6, “The protocol specific statistics windows”
Messages...
LTE MAC... See Section 9.4, “LTE MAC Traffic Statistics”
LTE RLC... See Section 9.5, “LTE RLC Traffic Statistics”
MTP3 See Section 9.6, “The protocol specific statistics windows”
RTP See Section 9.2, “RTP Analysis”
SCTP See Section 9.6, “The protocol specific statistics windows”
SIP... See Section 9.6, “The protocol specific statistics windows”
SMPP See Section 9.6, “The protocol specific statistics windows”
Operations...
UCP See Section 9.6, “The protocol specific statistics windows”
Messages...
VoIP Calls... See Section 9.3, “VoIP Calls”
WAP-WSP... See Section 9.6, “The protocol specific statistics windows”
3.13. The "Tools" menu

The Wireshark Tools menu contains the fields shown in Table 3.10, “Tools menu items”.
Table 3.10. Tools menu items

Firewall ACL This allows you to create command-line ACL rules for many
Rules different firewall products, including Cisco IOS, Linux Netfilter
(iptables), OpenBSD pf and Windows Firewall (via netsh). Rules
for MAC addresses, IPv4 addresses, TCP and UDP ports, and
IPv4+port combinations are supported.
It is assumed that the rules will be applied to an outside interface.
3.14. The "Help" menu

The Wireshark Help menu contains the fields shown in Table 3.11, “Help menu items”.
36
User Interface
Figure 3.11. The "Help" Menu
Table 3.11. Help menu items

Contents F1 This menu item brings up a basic help system.
FAQ's This menu item starts a Web browser showing various FAQ's.
Manual Pages This menu item starts a Web browser showing one of the locally
> ... installed html manual pages.
------
Wireshark This menu item starts a Web browser showing the chosen webpage
Online > ... from: http://www.wireshark.org.
------
Supported This menu item brings up a dialog box showing the supported
Protocols protocols and protocol fields.
(slow!)
------
About This menu item brings up an information window that provides
Wireshark some information on Wireshark, such as the plugins, the used
folders, ...
Note!
Calling a Web browser might be unsupported in your version of Wireshark. If this is the case,
the corresponding menu items will be hidden.
37
User Interface
Note!
If calling a Web browser fails on your machine, maybe because just nothing happens or
the browser is started but no page is shown, have a look at the web browser setting in the
preferences dialog.
3.15. The "Main" toolbar

The main toolbar provides quick access to frequently used items from the menu. This toolbar cannot be
customized by the user, but it can be hidden using the View menu, if the space on the screen is needed
to show even more packet data.
As in the menu, only the items useful in the current program state will be available. The others will be
greyed out (e.g. you cannot save a capture file if you haven't loaded one).
Figure 3.12. The "Main" toolbar
38
packets in the capture file. It pops up the Wireshark
Print dialog box (which is discussed further in
Section 5.7, “Printing packets”).
------ User Interface
Find Packet... Edit/Find Packet... This item brings up a dialog box that allows you to
find a packet. There is further information on finding
Table 3.12. Main toolbar items
packets in Section 6.8, “Finding packets”.
Go Back Go/Go Back This item jumps back in the packet history.
Go Forward Go/Go Forward This item jumps forward in the packet history.
Go to Packet... Go/Go to Packet... This item brings up a dialog box that allows you to
specify a packet number to go to that packet.
Go To First Go/First Packet This item jumps to the first packet of the capture file.
Packet
Go To Last Go/Last Packet This item jumps to the last packet of the capture file.
Packet
------
Colorize View/Colorize Colorize the packet list (or not).
Auto Scroll in View/Auto Scroll Auto scroll packet list while doing a live capture (or
Live Capture in Live Capture not).
------
Zoom In View/Zoom In Zoom into the packet data (increase the font size).
Zoom Out View/Zoom Out Zoom out of the packet data (decrease the font size).
Normal Size View/Normal Size Set zoom level back to 100%.
Resize Columns View/Resize Resize columns, so the content fits into them.
Columns
------
Capture Filters... Capture/Capture This item brings up a dialog box that allows you to
Filters... create and edit capture filters. You can name filters,
and you can save them for future use. More detail on
this subject is provided in Section 6.6, “Defining and
saving filters”.
Display Filters... Analyze/Display This item brings up a dialog box that allows you to
Filters... create and edit display filters. You can name filters,
and you can save them for future use. More detail on
this subject is provided in Section 6.6, “Defining and
saving filters”.
Coloring Rules... View/Coloring This item brings up a dialog box that allows you
Rules... color packets in the packet list pane according to
filter expressions you choose. It can be very useful
for spotting certain types of packets. More detail
on this subject is provided in Section 10.3, “Packet
colorization”.
Preferences... Edit/Preferences This item brings up a dialog box that allows you
to set preferences for many parameters that control
Wireshark. You can also save your preferences so
Wireshark will use them the next time you start it.
More detail is provided in Section 10.5, “Preferences”
------
Help Help/Contents This item brings up help dialog box.
39
User Interface
3.16. The "Filter" toolbar

The filter toolbar lets you quickly edit and apply display filters. More information on display filters is
available in Section 6.3, “Filtering packets while viewing”.
Figure 3.13. The "Filter" toolbar
Table 3.13. Filter toolbar items
Toolbar Toolbar Item Description

Icon
Filter: Brings up the filter construction dialog, described in Figure 6.7, “The
"Capture Filters" and "Display Filters" dialog boxes”.
Filter input The area to enter or edit a display filter string, see Section 6.4, “Building
display filter expressions” . A syntax check of your filter string is done
while you are typing. The background will turn red if you enter an
incomplete or invalid string, and will become green when you enter a
valid string. You can click on the pull down arrow to select a previously-
entered filter string from a list. The entries in the pull down list will remain
available even after a program restart.
Note!
After you've changed something in this field, don't forget to
press the Apply button (or the Enter/Return key), to apply this
filter string to the display.
Note!
This field is also where the current filter in effect is displayed.
Expression... The middle button labeled "Add Expression..." opens a dialog box that
lets you edit a display filter from a list of protocol fields, described in
Section 6.5, “The "Filter Expression" dialog box”
Clear Reset the current display filter and clears the edit area.
Apply Apply the current value in the edit area as the new display filter.
Note!
Applying a display filter on large capture files might take
quite a long time!
3.17. The "Packet List" pane

The packet list pane displays all the packets in the current capture file.
40
User Interface
Figure 3.14. The "Packet List" pane
Each line in the packet list corresponds to one packet in the capture file. If you select a line in this pane,
more details will be displayed in the "Packet Details" and "Packet Bytes" panes.
While dissecting a packet, Wireshark will place information from the protocol dissectors into the columns.
As higher level protocols might overwrite information from lower levels, you will typically see the
information from the highest possible level only.
For example, let's look at a packet containing TCP inside IP inside an Ethernet packet. The Ethernet
dissector will write its data (such as the Ethernet addresses), the IP dissector will overwrite this by its own
(such as the IP addresses), the TCP dissector will overwrite the IP information, and so on.
There are a lot of different columns available. Which columns are displayed can be selected by preference
settings, see Section 10.5, “Preferences”.
The default columns will show:
• No. The number of the packet in the capture file. This number won't change, even if a display filter
is used.
• Time The timestamp of the packet. The presentation format of this timestamp can be changed, see
Section 6.12, “Time display formats and time references”.
• Source The address where this packet is coming from.
• Destination The address where this packet is going to.
• Protocol The protocol name in a short (perhaps abbreviated) version.
• Info Additional information about the packet content.
There is a context menu (right mouse click) available, see details in Figure 6.3, “Pop-up menu of the
"Packet List" pane”.
3.18. The "Packet Details" pane

The packet details pane shows the current packet (selected in the "Packet List" pane) in a more detailed
form.
Figure 3.15. The "Packet Details" pane
41
User Interface
This pane shows the protocols and protocol fields of the packet selected in the "Packet List" pane. The
protocols and fields of the packet are displayed using a tree, which can be expanded and collapsed.
There is a context menu (right mouse click) available, see details in Figure 6.4, “Pop-up menu of the
"Packet Details" pane”.
Some protocol fields are specially displayed.
• Generated fields Wireshark itself will generate additional protocol fields which are surrounded by
brackets. The information in these fields is derived from the known context to other packets in the
capture file. For example, Wireshark is doing a sequence/acknowledge analysis of each TCP stream,
which is displayed in the [SEQ/ACK analysis] fields of the TCP protocol.
• Links If Wireshark detected a relationship to another packet in the capture file, it will generate a link
to that packet. Links are underlined and displayed in blue. If double-clicked, Wireshark jumps to the
corresponding packet.
3.19. The "Packet Bytes" pane

The packet bytes pane shows the data of the current packet (selected in the "Packet List" pane) in a hexdump
style.
Figure 3.16. The "Packet Bytes" pane
As usual for a hexdump, the left side shows the offset in the packet data, in the middle the packet data is
shown in a hexadecimal representation and on the right the corresponding ASCII characters (or . if not
appropriate) are displayed.
Depending on the packet data, sometimes more than one page is available, e.g. when Wireshark has
reassembled some packets into a single chunk of data, see Section 7.6, “Packet Reassembling”. In this case
there are some additional tabs shown at the bottom of the pane to let you select the page you want to see.
Figure 3.17. The "Packet Bytes" pane with tabs
Note!
The additional pages might contain data picked from multiple packets.
The context menu (right mouse click) of the tab labels will show a list of all available pages. This can be
helpful if the size in the pane is too small for all the tab labels.
3.20. The Statusbar

The statusbar displays informational messages.
42
User Interface
In general, the left side will show context related information, the middle part will show the current number
of packets, and the right side will show the selected configuration profile. Drag the handles between the
text areas to change the size.
Figure 3.18. The initial Statusbar
This statusbar is shown while no capture file is loaded, e.g. when Wireshark is started.
Figure 3.19. The Statusbar with a loaded capture file
• The colorized bullet on the left shows the highest expert info level found in the currently loaded
capture file. Hovering the mouse over this icon will show a textual description of the expert info level,
and clicking the icon will bring up the Expert Infos dialog box. For a detailed description of expert
info, see Section 7.3, “Expert Infos”.
• The left side shows information about the capture file, its name, its size and the elapsed time while
it was being captured.
• The middle part shows the current number of packets in the capture file. The following values are
displayed:
• Packets: the number of captured packets
• Displayed: the number of packets currently being displayed
• Marked: the number of marked packets
• Dropped: the number of dropped packets (only displayed if Wireshark was unable to capture all
packets)
• The right side shows the selected configuration profile. Clicking in this part of the statusbar will
bring up a menu with all available configuration profiles, and selecting from this list will change the
configuration profile.
Figure 3.20. The Statusbar with a configuration profile menu
For a detailed description of configuration profiles, see Section 10.6, “Configuration Profiles”.
Figure 3.21. The Statusbar with a selected protocol field
This is displayed if you have selected a protocol field from the "Packet Details" pane.
43
User Interface
Tip!
The value between the brackets (in this example arp.opcode) can be used as a display filter
string, representing the selected protocol field.
Figure 3.22. The Statusbar with a display filter message
This is displayed if you are trying to use a display filter which may have unexpected results. For a detailed
description, see Section 6.4.4, “A common mistake”.
44
Chapter 4. Capturing Live Network
Data
4.1. Introduction
Capturing live network data is one of the major features of Wireshark.
The Wireshark capture engine provides the following features:
• Capture from different kinds of network hardware (Ethernet, Token Ring, ATM, ...).
• Stop the capture on different triggers like: amount of captured data, captured time, captured number
of packets.
• Simultaneously show decoded packets while Wireshark keeps on capturing.
• Filter packets, reducing the amount of data to be captured, see Section 4.10, “Filtering while capturing”.
• Capturing into multiple files while doing a long term capture, and in addition the option to form
a ringbuffer of these files, keeping only the last x files, useful for a "very long term" capture, see
Section 4.8, “Capture files and file modes”.
The capture engine still lacks the following features:
• Simultaneous capturing from multiple network interfaces (however, you can start multiple instances
of Wireshark and merge capture files later).
• Stop capturing (or doing some other action), depending on the captured data.
4.2. Prerequisites
Setting up Wireshark to capture packets for the first time can be tricky.
Tip!
A comprehensive guide "How To setup a Capture" is available at: http://wiki.wireshark.org/
CaptureSetup.
Here are some common pitfalls:
• You need to have root / Administrator privileges to start a live capture.
• You need to choose the right network interface to capture packet data from.
• You need to capture at the right place in the network to see the traffic you want to see.
• ... and a lot more!.
If you have any problems setting up your capture environment, you should have a look at the guide
mentioned above.
45
Capturing Live Network Data
4.3. Start Capturing

One of the following methods can be used to start capturing packets with Wireshark:
• You can get an overview of the available local interfaces using the " Capture Interfaces" dialog
box, see Figure 4.1, “The "Capture Interfaces" dialog box on Microsoft Windows” or Figure 4.2, “The
"Capture Interfaces" dialog box on Unix/Linux”. You can start a capture from this dialog box, using
(one of) the "Capture" button(s).
• You can start capturing using the " Capture Options" dialog box, see Figure 4.3, “The "Capture
Options" dialog box”.
• If you have selected the right capture options before, you can immediately start a capture using the
" Capture Start" menu / toolbar item. The capture process will start immediately.
• If you already know the name of the capture interface, you can start Wireshark from the command
line and use the following:
wireshark -i eth0 -k
This will start Wireshark capturing on interface eth0, more details can be found at: Section 10.2, “Start
Wireshark from the command line”.
4.4. The "Capture Interfaces" dialog box

When you select "Interfaces..." from the Capture menu, Wireshark pops up the "Capture Interfaces" dialog
box as shown in Figure 4.1, “The "Capture Interfaces" dialog box on Microsoft Windows” or Figure 4.2,
“The "Capture Interfaces" dialog box on Unix/Linux”.
This dialog consumes lot's of system resources!

As the "Capture Interfaces" dialog is showing live captured data, it is consuming a lot of
system resources. Close this dialog as soon as possible to prevent excessive system load.
Not all available interfaces may be displayed!

This dialog box will only show the local interfaces Wireshark knows of. It will not show
interfaces marked as hidden in Section 10.5.1, “Interface Options”. As Wireshark might not
be able to detect all local interfaces, and it cannot detect the remote interfaces available, there
could be more capture interfaces available than listed.
Figure 4.1. The "Capture Interfaces" dialog box on Microsoft Windows
46
Figure 4.2. The "Capture Interfaces" dialog box on Unix/Linux
Device (Unix/Linux only) The interface device name.
Description The interface description provided by the operating system, or the

user defined comment added in Section 10.5.1, “Interface Options”.
IP The first IP address Wireshark could resolve from this interface.

If no address could be resolved (e.g. no DHCP server available),
"unknown" will be displayed. If more than one IP address could be
resolved, only the first is shown (unpredictable which one in that
case).
Packets The number of packets captured from this interface, since this
dialog was opened. Will be greyed out, if no packet was captured
in the last second.
Packets/s Number of packets captured in the last second. Will be greyed out,
if no packet was captured in the last second.
Stop Stop a currently running capture.
Start Start a capture on this interface immediately, using the settings from
the last capture.
Options Open the Capture Options dialog with this interface selected, see
Section 4.5, “The "Capture Options" dialog box”.
Details (Microsoft Windows only) Open a dialog with detailed information about the interface, see
Section 4.7, “The "Interface Details" dialog box”.
Help Show this help page.
Close Close this dialog box.
4.5. The "Capture Options" dialog box

When you select Start... from the Capture menu (or use the corresponding item in the "Main" toolbar),
Wireshark pops up the "Capture Options" dialog box as shown in Figure 4.3, “The "Capture Options"
dialog box”.
47
Figure 4.3. The "Capture Options" dialog box
Tip!
If you are unsure which options to choose in this dialog box, just try keeping the defaults as
this should work well in many cases.
You can set the following fields in this dialog box:
4.5.1. Capture frame

Interface (Windows only) The drop down list allows you to select the group of interfaces
you want look at. Normally that would be the local interfaces, but
here you can also select a remote interface. Any previously opened
remote interfaces will be added to this list also.
Interface This field specifies the interface you want to capture on. You
can only capture on one interface, and you can only capture on
interfaces that Wireshark has found on the system, either local or
remote. It is a drop-down list, so simply click on the button on the
48
right hand side and select the interface you want. It defaults to the
first non-loopback interface that supports capturing, and if there
are none, the first loopback interface. On some systems, loopback
interfaces cannot be used for capturing
Note
loopback interfaces are not available on Windows
platforms.
This field performs the same function as the -i <interface>

command line option.
IP address The IP address(es) of the selected interface. If no address could be

resolved from the system, "unknown" will be shown.
Link-layer header type Unless you are in the rare situation that you need this, just keep
the default. For a detailed description, see Section 4.9, “Link-layer
header type”
Remote setting (Windows only) Here you can set the settings for remote capture. For a detailed
description, see Section 4.6, “The "Remote Capture Interfaces"
dialog box”
Buffer size: n megabyte(s) Enter the buffer size to be used while capturing. This is the size of
the kernel buffer which will keep the captured packets, until they
are written to disk. If you encounter packet drops, try increasing
this value.
Note
This option is only available on Windows platforms.
Capture packets in promiscuous This checkbox allows you to specify that Wireshark should put
mode the interface in promiscuous mode when capturing. If you do not
specify this, Wireshark will only capture the packets going to or
from your computer (not all packets on your LAN segment).
Note
If some other process has put the interface in
promiscuous mode you may be capturing in
promiscuous mode even if you turn off this option.
Note
Even in promiscuous mode you still won't necessarily
see all packets on your LAN segment, see http://
www.wireshark.org/faq.html#promiscsniff for some
more explanations.
Capture packets in pcap-ng This checkbox allows you to specify that Wireshark saves the
format captured packets in pcap-ng format. This next generation capture
file format is currently in development.
49
Warning
This is an experimental feature. The resulting
saved file may or may not be valid. See http:/
/wiki.wireshark.org/Development/PcapNg for more
details on pcap-ng.
Limit each packet to n bytes This field allows you to specify the maximum amount of data that
will be captured for each packet, and is sometimes referred to as the
snaplen. If disabled, the value is set to the maximum 65535, which
will be sufficient for most protocols. Some rules of thumb:
• If you are unsure, just keep the default value.
• If you don't need all of the data in a packet - for example, if you
only need the link-layer, IP, and TCP headers - you might want
to choose a small snapshot length, as less CPU time is required
for copying packets, less buffer space is required for packets,
and thus perhaps fewer packets will be dropped if traffic is very
heavy.
• If you don't capture all of the data in a packet, you might find
that the packet data you want is in the part that's dropped, or that
reassembly isn't possible as the data required for reassembly is
missing.
Capture Filter This field allows you to specify a capture filter. Capture filters
are discussed in more details in Section 4.10, “Filtering while
capturing”. It defaults to empty, or no filter.
You can also click on the button labeled "Capture Filter", and
Wireshark will bring up the Capture Filters dialog box and allow
you to create and/or select a filter. Please see Section 6.6, “Defining
and saving filters”
4.5.2. Capture File(s) frame

An explanation about capture file usage can be found in Section 4.8, “Capture files and file modes”.
File This field allows you to specify the file name that will be used for
the capture file. This field is left blank by default. If the field is
left blank, the capture data will be stored in a temporary file, see
Section 4.8, “Capture files and file modes” for details.
You can also click on the button to the right of this field to browse
through the filesystem.
Use multiple files Instead of using a single file, Wireshark will automatically switch
to a new one, if a specific trigger condition is reached.
Next file every n megabyte(s) Multiple files only: Switch to the next file after the given number
of byte(s)/kilobyte(s)/megabyte(s)/gigabyte(s) have been captured.
Next file every n minute(s) Multiple files only: Switch to the next file after the given number
of second(s)/minutes(s)/hours(s)/days(s) have elapsed.
50
Ring buffer with n files Multiple files only: Form a ring buffer of the capture files, with the
given number of files.
Stop capture after n file(s) Multiple files only: Stop capturing after switching to the next file
the given number of times.
4.5.3. Stop Capture... frame

... after n packet(s) Stop capturing after the given number of packets have been
captured.
... after n megabytes(s) Stop capturing after the given number of byte(s)/kilobyte(s)/
megabyte(s)/gigabyte(s) have been captured. This option is greyed
out, if "Use multiple files" is selected.
... after n minute(s) Stop capturing after the given number of second(s)/minutes(s)/
hours(s)/days(s) have elapsed.
4.5.4. Display Options frame

Update list of packets in real This option allows you to specify that Wireshark should update the
time packet list pane in real time. If you do not specify this, Wireshark
does not display any packets until you stop the capture. When you
check this, Wireshark captures in a separate process and feeds the
captures to the display process.
Automatic scrolling in live This option allows you to specify that Wireshark should scroll the
capture packet list pane as new packets come in, so you are always looking
at the last packet. If you do not specify this, Wireshark simply adds
new packets onto the end of the list, but does not scroll the packet
list pane. This option is greyed out if "Update list of packets in real
time" is disabled.
Hide capture info dialog If this option is checked, the capture info dialog described in
Section 4.11, “While a Capture is running ...” will be hidden.
4.5.5. Name Resolution frame

Enable MAC name resolution This option allows you to control whether or not Wireshark
translates MAC addresses into names, see Section 7.7, “Name
Resolution”.
Enable network name resolution This option allows you to control whether or not Wireshark
translates network addresses into names, see Section 7.7, “Name
Resolution”.
Enable transport name This option allows you to control whether or not Wireshark
resolution translates transport addresses into protocols, see Section 7.7,
“Name Resolution”.
4.5.6. Buttons
Once you have set the values you desire and have selected the options you need, simply click on Start to
commence the capture, or Cancel to cancel the capture.
51
If you start a capture, Wireshark allows you to stop capturing when you have enough packets captured,
for details see Section 4.11, “While a Capture is running ...”.
4.6. The "Remote Capture Interfaces" dialog

box
Besides doing capture on local interfaces Wireshark is capable of reaching out across the network to a so
called capture daemon or service processes to receive captured data from.
Microsoft Windows only

This dialog and capability is only available on Microsoft Windows. On Linux/Unix you can
achieve the same effect (securely) through an SSH tunnel.
The Remote Packet Capture Protocol service must first be running on the target platform before Wireshark
can connect to it. The easiest way is to install WinPcap from http://www.winpcap.org/install/default.htm
on the target. Once installation is completed go to the Services control panel, find the Remote Packet
Capture Protocol service and start it.
Note
Make sure you have outside access to port 2002 on the target platform. This is the port where
the Remote Packet Capture Protocol service can be reached, by default.
To access the Remote Capture Interfaces dialog use the Interfaces dropdown list on the "Capture Options"
dialog, see Figure 4.3, “The "Capture Options" dialog box”, and select "Remote...".
52
4.6.1. Remote Capture Interfaces

Figure 4.4. The "Remote Capture Interfaces" dialog box
You have to set the following parameter in this dialog:
Host Enter the IP address or host name of the target platform where the
Remote Packet Capture Protocol service is listening.
Port Set the port number where the Remote Packet Capture Protocol
service is listening on. Leave open to use the default port (2002).
Null authentication Select this if you don't need authentication to take place for a
remote capture to be started. This depends on the target platform.
Configuring the target platform like this makes it insecure.
Password authentication This is the normal way of connecting to a target platform. Set the
credentials needed to connect to the Remote Packet Capture Protocol
service.
53
4.6.2. Remote Capture

When the connection to the Remote Packet Capture Protocol service is successfully established the
"Capture Options" dialog looks like this, see Figure 4.5, “The "Remote Capture" dialog box”.
Figure 4.5. The "Remote Capture" dialog box
The Interface dropdown list now shows the IP address or host name of the Remote Packet Capture Protocol
service and the other field shows the interfaces on the remote target. After selecting the desired interface
just click Start to start the remote capture.
4.6.3. Remote Capture Settings

The remote capture can be furhter fine tuned to match your situation. The Remote Settings button gives
you this option. It pops up the dialog shown in Figure 4.6, “The "Remote Capture Settings" dialog box”.
54
Figure 4.6. The "Remote Capture Settings" dialog box
You can set the following parameters in this dialog:
Do not capture own RPCAP This option sets a capture filter so that the traffic flowing back
traffic from the Remote Packet Capture Protocol service to Wireshark isn't
captured as well and also send back. The recursion in this saturates
the link with duplicate traffic.
You only should switch this off when capturing on an interface

other then the interface connecting back to Wireshark.
Use UDP for data transfer Remote capture control and data flows over a TCP connection. This
option allows you to choose an UDP stream for data transfer.
Sampling option None This option instructs the Remote Packet Capture Protocol service
to send back all captured packets which have passed the capture
filter. This is usually not a problem on a remote capture session with
sufficient bandwidth.
Sampling option 1 of x packets This option limits the Remote Packet Capture Protocol service to
send only a sub sampling of the captured data, in terms of number
55
of packets. This allows capture over a narrow band remote capture

session of a higher bandwidth interface.
Sampling option 1 every x This option limits the Remote Packet Capture Protocol service to
milliseconds send only a sub sampling of the captured data, in terms of time.
This allows capture over a narrow band capture session of a higher
bandwidth interface.
4.7. The "Interface Details" dialog box

When you select Details from the Capture Interface menu, Wireshark pops up the "Interface Details" dialog
box as shown in Figure 4.7, “The "Interface Details" dialog box”. This dialog shows various characteristics
and statistics for the selected interface.
Microsoft Windows only

This dialog is only available on Microsoft Windows
Figure 4.7. The "Interface Details" dialog box
4.8. Capture files and file modes

While capturing, the underlying libpcap capturing engine will grab the packets from the network card and
keep the packet data in a (relatively) small kernel buffer. This data is read by Wireshark and saved into
the capture file(s) the user specified.
Different modes of operation are available when saving this packet data to the capture file(s).
Tip!
Working with large files (several 100 MB's) can be quite slow. If you plan to do a long term
capture or capturing from a high traffic network, think about using one of the "Multiple files"
56
options. This will spread the captured packets over several smaller files which can be much
more pleasant to work with.
Note!
Using Multiple files may cut context related information. Wireshark keeps context
information of the loaded packet data, so it can report context related problems (like a stream
error) and keeps information about context related protocols (e.g. where data is exchanged
at the establishing phase and only referred to in later packets). As it keeps this information
only for the loaded file, using one of the multiple file modes may cut these contexts. If the
establishing phase is saved in one file and the things you would like to see is in another, you
might not see some of the valuable context related information.
Tip!
Information about the folders used for the capture file(s), can be found in Appendix A, Files
and Folders.
Table 4.1. Capture file mode selected by capture options
"File" option "Use multiple "Ring buffer with Mode Resulting filename(s)
files" option n files" option used
- - - Single temporary etherXXXXXX (where
file XXXXXX is a unique
number)
foo.cap - - Single named file foo.cap
foo.cap x - Multiple files, foo_00001_20040205110102.cap,
continuous foo_00002_20040205110102.cap, ...
foo.cap x x Multiple files, foo_00001_20040205110102.cap,
ring buffer foo_00002_20040205110102.cap, ...
Single temporary file A temporary file will be created and used (this is the default). After
the capturing is stopped, this file can be saved later under a user
specified name.
Single named file A single capture file will be used. If you want to place the new
capture file to a specific folder, choose this mode.
Multiple files, continuous Like the "Single named file" mode, but a new file is created and
used, after reaching one of the multiple file switch conditions (one
of the "Next file every ..." values).
Multiple files, ring buffer Much like "Multiple files continuous", reaching one of the multiple
files switch conditions (one of the "Next file every ..." values) will
switch to the next file. This will be a newly created file if value of
"Ring buffer with n files" is not reached, otherwise it will replace
the oldest of the formerly used files (thus forming a "ring").
This mode will limit the maximum disk usage, even for an unlimited
amount of capture input data, keeping the latest captured data.
57
4.9. Link-layer header type

In the usual case, you won't have to choose this link-layer header type. The following paragraphs describe
the exceptional cases, where selecting this type is possible, so you will have a guide of what to do:
If you are capturing on an 802.11 device on some versions of BSD, this might offer a choice of "Ethernet"
or "802.11". "Ethernet" will cause the captured packets to have fake Ethernet headers; "802.11" will cause
them to have IEEE 802.11 headers. Unless the capture needs to be read by an application that doesn't
support 802.11 headers, you should select "802.11".
If you are capturing on an Endace DAG card connected to a synchronous serial line, this might offer a
choice of "PPP over serial" or "Cisco HDLC"; if the protocol on the serial line is PPP, select "PPP over
serial", and if the protocol on the serial line is Cisco HDLC, select "Cisco HDLC".
If you are capturing on an Endace DAG card connected to an ATM network, this might offer a choice
of "RFC 1483 IP-over-ATM" or "Sun raw ATM". If the only traffic being captured is RFC 1483 LLC-
encapsulated IP, or if the capture needs to be read by an application that doesn't support SunATM headers,
select "RFC 1483 IP-over-ATM", otherwise select "Sun raw ATM".
If you are capturing on an Ethernet device, this might offer a choice of "Ethernet" or "DOCSIS". If you
are capturing traffic from a Cisco Cable Modem Termination System that is putting DOCSIS traffic onto
the Ethernet to be captured, select "DOCSIS", otherwise select "Ethernet".
4.10. Filtering while capturing

Wireshark uses the libpcap filter language for capture filters. This is explained in the tcpdump man page,
which can be hard to understand, so it's explained here to some extent.
Tip!
You will find a lot of Capture Filter examples at http://wiki.wireshark.org/CaptureFilters.
You enter the capture filter into the Filter field of the Wireshark Capture Options dialog box, as shown
in Figure 4.3, “The "Capture Options" dialog box”. The following is an outline of the syntax of the
tcpdump capture filter language. See the expression option at the tcpdump manual page for details: http:/
/www.tcpdump.org/tcpdump_man.html.
A capture filter takes the form of a series of primitive expressions connected by conjunctions (and/or)
and optionally preceded by not:
[not] primitive [and|or [not] primitive ...]
An example is shown in Example 4.1, “ A capture filter for telnet that captures traffic to and from a
particular host ”.
Example 4.1. A capture filter for telnet that captures traffic to and from a particular
host
tcp port 23 and host 10.0.0.5
This example captures telnet traffic to and from the host 10.0.0.5, and shows how to use two primitives
and the and conjunction. Another example is shown in Example 4.2, “ Capturing all telnet traffic not from
10.0.0.5”, and shows how to capture all telnet traffic except that from 10.0.0.5.
58
Example 4.2. Capturing all telnet traffic not from 10.0.0.5
tcp port 23 and not src host 10.0.0.5
XXX - add examples to the following list.
A primitive is simply one of the following:
[src|dst] host <host> This primitive allows you to filter on a host IP address or name.
You can optionally precede the primitive with the keyword src|
dst to specify that you are only interested in source or destination
addresses. If these are not present, packets where the specified
address appears as either the source or the destination address will
be selected.
ether [src|dst] host <ehost> This primitive allows you to filter on Ethernet host addresses. You
can optionally include the keyword src|dst between the keywords
ether and host to specify that you are only interested in source or
destination addresses. If these are not present, packets where the
specified address appears in either the source or destination address
will be selected.
gateway host <host> This primitive allows you to filter on packets that used host as a
gateway. That is, where the Ethernet source or destination was host
but neither the source nor destination IP address was host.
[src|dst] net <net> [{mask This primitive allows you to filter on network numbers. You
<mask>}|{len <len>}] can optionally precede this primitive with the keyword src|dst
to specify that you are only interested in a source or destination
network. If neither of these are present, packets will be selected
that have the specified network in either the source or destination
address. In addition, you can specify either the netmask or the CIDR
prefix for the network if they are different from your own.
[tcp|udp] [src|dst] port <port> This primitive allows you to filter on TCP and UDP port numbers.
You can optionally precede this primitive with the keywords src|dst
and tcp|udp which allow you to specify that you are only interested
in source or destination ports and TCP or UDP packets respectively.
The keywords tcp|udp must appear before src|dst.
If these are not specified, packets will be selected for both the TCP
and UDP protocols and when the specified address appears in either
the source or destination port field.
less|greater <length> This primitive allows you to filter on packets whose length was less
than or equal to the specified length, or greater than or equal to the
specified length, respectively.
ip|ether proto <protocol> This primitive allows you to filter on the specified protocol at either
the Ethernet layer or the IP layer.
ether|ip broadcast|multicast This primitive allows you to filter on either Ethernet or IP

broadcasts or multicasts.
<expr> relop <expr> This primitive allows you to create complex filter expressions that
select bytes or ranges of bytes in packets. Please see the tcpdump
59
man page at http://www.tcpdump.org/tcpdump_man.html for more

details.
4.10.1. Automatic Remote Traffic Filtering

If Wireshark is running remotely (using e.g. SSH, an exported X11 window, a terminal server, ...), the
remote content has to be transported over the network, adding a lot of (usually unimportant) packets to
the actually interesting traffic.
To avoid this, Wireshark tries to figure out if it's remotely connected (by looking at some specific
environment variables) and automatically creates a capture filter that matches aspects of the connection.
The following environment variables are analyzed:
SSH_CONNECTION (ssh) <remote IP> <remote port> <local IP> <local port>
SSH_CLIENT (ssh) <remote IP> <remote port> <local port>
REMOTEHOST (tcsh, others?) <remote name>
DISPLAY (x11) [remote name]:<display num>
SESSIONNAME (terminal server) <remote name>
4.11. While a Capture is running ...

While a capture is running, the following dialog box is shown:
Figure 4.8. The "Capture Info" dialog box
This dialog box will inform you about the number of captured packets and the time since the capture was
started. The selection of which protocols are counted cannot be changed.
Tip!
This Capture Info dialog box can be hidden, using the "Hide capture info dialog" option in
the Capture Options dialog box.
60
4.11.1. Stop the running capture

A running capture session will be stopped in one of the following ways:
1. Using the " Stop" button from the Capture Info dialog box .
Note!
The Capture Info dialog box might be hidden, if the option "Hide capture info dialog"
is used.
2. Using the menu item "Capture/ Stop".
3. Using the toolbar item " Stop".
4. Pressing the accelerator keys: Ctrl+E.
5. The capture will be automatically stopped, if one of the Stop Conditions is exceeded, e.g. the
maximum amount of data was captured.
4.11.2. Restart a running capture

A running capture session can be restarted with the same capture options as the last time, this will remove
all packets previously captured. This can be useful, if some uninteresting packets are captured and there's
no need to keep them.
Restart is a convenience function and equivalent to a capture stop following by an immediate capture start.
A restart can be triggered in one of the following ways:
1. Using the menu item "Capture/ Restart".
2. Using the toolbar item " Restart".
61
Chapter 5. File Input / Output and
Printing
5.1. Introduction
This chapter will describe input and output of capture data.
• Open/Import capture files in various capture file formats
• Save/Export capture files in various capture file formats
• Merge capture files together
• Print packets
5.2. Open capture files

Wireshark can read in previously saved capture files. To read them, simply select the menu or toolbar
item: "File/ Open". Wireshark will then pop up the File Open dialog box, which is discussed in more
detail in Section 5.2.1, “The "Open Capture File" dialog box”.
It's convenient to use drag-and-drop!

... to open a file, by simply dragging the desired file from your file manager and dropping it
onto Wireshark's main window. However, drag-and-drop is not available/won't work in all
desktop environments.
If you haven't previously saved the current capture file, you will be asked to do so, to prevent data loss
(this behaviour can be disabled in the preferences).
In addition to its native file format (libpcap format, also used by tcpdump/WinDump and other libpcap/
WinPcap-based programs), Wireshark can read capture files from a large number of other packet capture
programs as well. See Section 5.2.2, “Input File Formats” for the list of capture formats Wireshark
understands.
5.2.1. The "Open Capture File" dialog box

The "Open Capture File" dialog box allows you to search for a capture file containing previously captured
packets for display in Wireshark. Table 5.1, “The system specific "Open Capture File" dialog box” shows
some examples of the Wireshark Open File Dialog box.
The dialog appearance depends on your system!

The appearance of this dialog depends on the system and/or GTK+ toolkit version used.
However, the functionality remains basically the same on any particular system.
Common dialog behaviour on all systems:
• Select files and directories.
62
File Input / Output and Printing
• Click the Open/Ok button to accept your selected file and open it.
• Click the Cancel button to go back to Wireshark and not load a capture file.
Wireshark extensions to the standard behaviour of these dialogs:
• View file preview information (like the filesize, the number of packets, ...), if you've selected a capture
file.
• Specify a display filter with the "Filter:" button and filter field. This filter will be used when opening
the new file. The text field background becomes green for a valid filter string and red for an invalid
one. Clicking on the Filter button causes Wireshark to pop up the Filters dialog box (which is discussed
further in Section 6.3, “Filtering packets while viewing”).
XXX - we need a better description of these read filters
• Specify which type of name resolution is to be performed for all packets by clicking on one of the "...
name resolution" check buttons. Details about name resolution can be found in Section 7.7, “Name
Resolution”.
Save a lot of time loading huge capture files!

You can change the display filter and name resolution settings later while viewing the
packets. However, loading huge capture files can take a significant amount of extra time if
these settings are changed later, so in such situations it can be a good idea to set at least the
filter in advance here.
63
Table 5.1. The system specific "Open Capture File" dialog box
Figure 5.1. "Open" on native Windows Microsoft Windows

This is the common Windows file open dialog - plus
some Wireshark extensions.
Specific for this dialog:
• If available, the "Help" button will lead you to

this section of this "User's Guide".
• XXX - the "Filter:" button currently doesn't

work on Windows!
• XXX - missing feature: If Wireshark doesn't

recognize the selected file as a capture file, it
should grey out the "Open" button.
Figure 5.2. "Open" - new GTK version Unix/Linux: GTK version >= 2.4
This is the common Gimp/GNOME file open dialog
- plus some Wireshark extensions.
• The "+ Add" button allows you to add a

directory, selected in the right-hand pane, to
the favorites list on the left. Those changes are
persistent.
• The "- Remove" button allows you to remove a

selected directory from that list again (the items
like: "Home", "Desktop", and "Filesystem"
cannot be removed).
• If Wireshark doesn't recognize the selected file

as a capture file, it will grey out the "Open"
button.
Figure 5.3. "Open" - old GTK version Unix/Linux: GTK version < 2.4
This is the file open dialog of former Gimp/

GNOME versions - plus some Wireshark
extensions.
• If Wireshark doesn't recognize the selected file

as a capture file, it will grey out the "Ok" button.
64
5.2.2. Input File Formats

The following file formats from other capture tools can be opened by Wireshark:
• libpcap, tcpdump and various other tools using tcpdump's capture format
• Sun snoop and atmsnoop
• Shomiti/Finisar Surveyor captures
• Novell LANalyzer captures
• Microsoft Network Monitor captures
• AIX's iptrace captures
• Cinco Networks NetXray captures
• Network Associates Windows-based Sniffer and Sniffer Pro captures
• Network General/Network Associates DOS-based Sniffer (compressed or uncompressed) captures
• AG Group/WildPackets EtherPeek/TokenPeek/AiroPeek/EtherHelp/PacketGrabber captures
• RADCOM's WAN/LAN Analyzer captures
• Network Instruments Observer version 9 captures
• Lucent/Ascend router debug output
• HP-UX's nettl
• Toshiba's ISDN routers dump output
• ISDN4BSD i4btrace utility
• traces from the EyeSDN USB S0
• IPLog format from the Cisco Secure Intrusion Detection System
• pppd logs (pppdump format)
• the output from VMS's TCPIPtrace/TCPtrace/UCX$TRACE utilities
• the text output from the DBS Etherwatch VMS utility
• Visual Networks' Visual UpTime traffic capture
• the output from CoSine L2 debug
• the output from Accellent's 5Views LAN agents
• Endace Measurement Systems' ERF format captures
• Linux Bluez Bluetooth stack hcidump -w traces
65
• Catapult DCT2000 .out files
• Gammu generated text output from Nokia DCT3 phones in Netmonitor mode
• IBM Series (OS/400) Comm traces (ASCII & UNICODE)
• Juniper Netscreen snoop captures
• Symbian OS btsnoop captures
• Tamosoft CommView captures
• Textronix K12xx 32bit .rf5 format captures
• Textronix K12 text file format captures
• Wireshark .pcapng captures (Experimental)
• ... new file formats are added from time to time
Opening a file may fail due to invalid packet types!

It may not be possible to read some formats dependent on the packet types captured. Ethernet
captures are usually supported for most file formats but it may not be possible to read other
packet types (e.g. token ring packets) from all file formats.
5.3. Saving captured packets

You can save captured packets simply by using the Save As... menu item from the File menu under
Wireshark. You can choose which packets to save and which file format to be used.
Saving may reduce the available information!

Saving the captured packets will slightly reduce the amount of information, e.g. the number
of dropped packets will be lost; see Section A.1, “Capture Files” for details.
5.3.1. The "Save Capture File As" dialog box

The "Save Capture File As" dialog box allows you to save the current capture to a file. Table 5.2, “The
system specific "Save Capture File As" dialog box” shows some examples of this dialog box.
The dialog appearance depends on your system!

The appearance of this dialog depends on the system and GTK+ toolkit version used.
However, the functionality remains basically the same on any particular system.
66
Figure 5.4. "Save" on native Windows Microsoft Windows

Table 5.2. The system specific "Save Capture
This isFile As" dialog
the common box file save dialog - plus
Windows
• If available, the "Help" button will lead you to

this section of this "User's Guide".
• If you don't provide a file extension to the

filename - e.g. .pcap, Wireshark will append the
standard file extension for that file format.
Figure 5.5. "Save" - new GTK version Unix/Linux: GTK version >= 2.4
This is the common Gimp/GNOME file save dialog

• Clicking on the + at "Browse for other folders"

will allow you to browse files and folders in your
file system.
Figure 5.6. "Save" - old GTK version Unix/Linux: GTK version < 2.4
This is the file save dialog of former Gimp/GNOME

versions - plus some Wireshark extensions.
67
With this dialog box, you can perform the following actions:
1. Type in the name of the file you wish to save the captured packets in, as a standard file name in your
file system.
2. Select the directory to save the file into.
3. Select the range of the packets to be saved, see Section 5.8, “The Packet Range frame”
4. Specify the format of the saved capture file by clicking on the File type drop down box. You can
choose from the types, described in Section 5.3.2, “Output File Formats”.
The selection of capture formats may be reduced!

Some capture formats may not be available, depending on the packet types captured.
File formats can be converted!

You can convert capture files from one format to another by reading in a capture file
and writing it out using a different format.
5. Click on the Save/Ok button to accept your selected file and save to it. If Wireshark has a problem
saving the captured packets to the file you specified, it will display an error dialog box. After clicking
OK on that error dialog box, you can try again.
6. Click on the Cancel button to go back to Wireshark and not save the captured packets.
5.3.2. Output File Formats

Wireshark can save the packet data in its "native" file format (libpcap) and in the file formats of some
other protocol analyzers, so other tools can read the capture data.
File formats have different time stamp accuracies!

Saving from the currently used file format to a different format may reduce the time stamp
accuracy; see the Section 7.4, “Time Stamps” for details.
The following file formats can be saved by Wireshark (with the known file extensions):
• libpcap, tcpdump and various other tools using tcpdump's capture format (*.pcap,*.cap,*.dmp)
• Accellent 5Views (*.5vw)
• HP-UX's nettl (*.TRC0,*.TRC1)
• Microsoft Network Monitor - NetMon (*.cap)
• Network Associates Sniffer - DOS (*.cap,*.enc,*.trc,*fdc,*.syc)
• Network Associates Sniffer - Windows (*.cap)
• Network Instruments Observer version 9 (*.bfr)
• Novell LANalyzer (*.tr1)
68
• Sun snoop (*.snoop,*.cap)
• Visual Networks Visual UpTime traffic (*.*)
• ... new file formats are added from time to time
If the above tools will be more helpful than Wireshark is a different question ;-)
Third party protocol analyzers may require specific file

extensions!
Other protocol analyzers than Wireshark may require that the file has a certain file extension
in order to read the files you generate with Wireshark, e.g.:
".cap" for Network Associates Sniffer - Windows
5.4. Merging capture files

Sometimes you need to merge several capture files into one. For example this can be useful, if you have
captured simultaneously from multiple interfaces at once (e.g. using multiple instances of Wireshark).
Merging capture files can be done in three ways:
• Use the menu item "Merge" from the "File" menu, to open the merge dialog, see Section 5.4.1, “The
"Merge with Capture File" dialog box”. This menu item will be disabled, until you have loaded a
capture file.
• Use drag-and-drop to drop multiple files on the main window. Wireshark will try to merge the packets
in chronological order from the dropped files into a newly created temporary file. If you drop only a
single file, it will simply replace a (maybe) existing one.
• Use the mergecap tool, which is a command line tool to merge capture files. This tool provides the
most options to merge capture files, see Section D.7, “mergecap: Merging multiple capture files into
one ”.
5.4.1. The "Merge with Capture File" dialog box

This dialog box let you select a file to be merged into the currently loaded file.
You will be prompted for an unsaved file first!

If your current data wasn't saved before, you will be asked to save it first, before this dialog
box is shown.
Most controls of this dialog will work the same way as described in the "Open Capture File" dialog box,
see Section 5.2.1, “The "Open Capture File" dialog box”.
Specific controls of this merge dialog are:
Prepend packets to existing file Prepend the packets from the selected file before the currently
loaded packets.
Merge packets chronologically Merge both the packets from the selected and currently loaded file
in chronological order.
69
Append packets to existing file Append the packets from the selected file after the currently loaded
packets.
Table 5.3. The system specific "Merge Capture File As" dialog box
Figure 5.7. "Merge" on native Windows Microsoft Windows

This is the common Windows file open dialog - plus
Figure 5.8. "Merge" - new GTK version Unix/Linux: GTK version >= 2.4
This is the common Gimp/GNOME file open dialog
Figure 5.9. "Merge" - old GTK version Unix/Linux: GTK version < 2.4
This is the file open dialog of former Gimp/
GNOME versions - plus some Wireshark
extensions.
5.5. File Sets

When using the "Multiple Files" option while doing a capture (see: Section 4.8, “Capture files and file
modes”), the capture data is spread over several capture files, called a file set.
As it can become tedious to work with a file set by hand, Wireshark provides some features to handle
these file sets in a convenient way.
70
How does Wireshark detect the files of a file set?
A filename in a file set uses the format Prefix_Number_DateTimeSuffix which might look like this:
"test_00001_20060420183910.pcap". All files of a file set share the same prefix (e.g. "test") and
suffix (e.g. ".pcap") and a varying middle part.
To find the files of a file set, Wireshark scans the directory where the currently loaded file resides
and checks for files matching the filename pattern (prefix and suffix) of the currently loaded file.
This simple mechanism usually works well, but has its drawbacks. If several file sets were captured
with the same prefix and suffix, Wireshark will detect them as a single file set. If files were renamed
or spread over several directories the mechanism will fail to find all files of a set.
The following features in the "File Set" submenu of the "File" menu are available to work with file sets
in a convenient way:
• The List Files dialog box will list the files Wireshark has recognized as being part of the current file set.
• Next File closes the current and opens the next file in the file set.
• Previous File closes the current and opens the previous file in the file set.
5.5.1. The "List Files" dialog box

Figure 5.10. The "List Files" dialog box
Each line contains information about a file of the file set:
• Filename the name of the file. If you click on the filename (or the radio button left to it), the current
file will be closed and the corresponding capture file will be opened.
• Created the creation time of the file
71
• Last Modified the last time the file was modified
• Size the size of the file
The last line will contain info about the currently used directory where all of the files in the file set can
be found.
The content of this dialog box is updated each time a capture file is opened/closed.
The Close button will, well, close the dialog box.
5.6. Exporting data

Wireshark provides several ways and formats to export packet data. This section describes general ways
to export data from Wireshark.
Note!
There are more specialized functions to export specific data, which will be described at the
appropriate places.
XXX - add detailed descriptions of the output formats and some sample output, too.
5.6.1. The "Export as Plain Text File" dialog box

Export packet data into a plain ASCII text file, much like the format used to print packets.
Figure 5.11. The "Export as Plain Text File" dialog box
• Export to file: frame chooses the file to export the packet data to.
• The Packet Range frame is described in Section 5.8, “The Packet Range frame”.
• The Packet Details frame is described in Section 5.9, “The Packet Format frame”.
5.6.2. The "Export as PostScript File" dialog box

Export packet data into PostScript, much like the format used to print packets.
72
Tip!
You can easily convert PostScript files to PDF files using ghostscript. For example: export
to a file named foo.ps and then call: ps2pdf foo.ps
Figure 5.12. The "Export as PostScript File" dialog box
• The Packet Details frame is described in Section 5.9, “The Packet Format frame”.
5.6.3. The "Export as CSV (Comma Separated Values)

File" dialog box
XXX - add screenshot
Export packet summary into CSV, used e.g. by spreadsheet programs to im-/export data.
5.6.4. The "Export as C Arrays (packet bytes) file" dialog

box
XXX - add screenshot
Export packet bytes into C arrays so you can import the stream data into your own C program.
5.6.5. The "Export as PSML File" dialog box

Export packet data into PSML. This is an XML based format including only the packet summary. The
PSML file specification is available at: http://www.nbee.org/doku.php?id=netpdl:psml_specification.
73
Figure 5.13. The "Export as PSML File" dialog box
There's no such thing as a packet details frame for PSML export, as the packet format is defined by the
PSML specification.
5.6.6. The "Export as PDML File" dialog box

Export packet data into PDML. This is an XML based format including the packet details. The PDML file
specification is available at: http://www.nbee.org/doku.php?id=netpdl:pdml_specification.
The PDML specification is not officially released and Wireshark's implementation of it is

still in an early beta state, so please expect changes in future Wireshark versions.
Figure 5.14. The "Export as PDML File" dialog box
There's no such thing as a packet details frame for PDML export, as the packet format is defined by the
PDML specification.
74
5.6.7. The "Export selected packet bytes" dialog box

Export the bytes selected in the "Packet Bytes" pane into a raw binary file.
Figure 5.15. The "Export Selected Packet Bytes" dialog box
• Name: the filename to export the packet data to.
• The Save in folder: field lets you select the folder to save to (from some predefined folders).
• Browse for other folders provides a flexible way to choose a folder.
5.6.8. The "Export Objects" dialog box

This feature scans through HTTP streams in the currently open capture file or running capture and
takes reassembled objects such as HTML documents, image files, executables and anything else that
can be transferred over HTTP and lets you save them to disk. If you have a capture running, this list is
automatically updated every few seconds with any new objects seen. The saved objects can then be opened
with the proper viewer or executed in the case of executables (if it is for the same platform you are running
Wireshark on) without any further work on your part. This feature is not available when using GTK2
versions below 2.4.
75
Figure 5.16. The "Export Objects" dialog box
Columns:
• Packet num: The packet number in which this object was found. In some cases, there can be multiple
objects in the same packet.
• Hostname: The hostname of the server that sent the object as a response to an HTTP request.
• Content Type: The HTTP content type of this object.
• Bytes: The size of this object in bytes.
• Filename: The final part of the URI (after the last slash). This is typically a filename, but may be
a long complex looking string, which typically indicates that the file was received in response to a
HTTP POST request.
Buttons:
• Help: Opens this section in the user's guide.
• Close: Closes this dialog.
• Save As: Saves the currently selected object as a filename you specify. The default filename to save
as is taken from the filename column of the objects list.
• Save All: Saves all objects in the list using the filename from the filename column. You will be asked
what directory / folder to save them in. If the filename is invalid for the operating system / file system
you are running Wireshark on, then an error will appear and that object will not be saved (but all of
the others will be).
76
5.7. Printing packets

To print packets, select the "Print..." menu item from the File menu. When you do this, Wireshark pops
up the Print dialog box as shown in Figure 5.17, “The "Print" dialog box”.
5.7.1. The "Print" dialog box

Figure 5.17. The "Print" dialog box
The following fields are available in the Print dialog box:
Printer This field contains a pair of mutually exclusive radio buttons:
• Plain Text specifies that the packet print should be in plain text.
• PostScript specifies that the packet print process should use PostScript to
generate a better print output on PostScript aware printers.
• Output to file: specifies that printing be done to a file, using the filename entered
in the field or selected with the browse button.
This field is where you enter the file to print to if you have selected Print to a
file, or you can click the button to browse the filesystem. It is greyed out if Print
to a file is not selected.
• Print command specifies that a command be used for printing.
Note!
These Print command fields are not available on windows
platforms.
This field specifies the command to use for printing. It is typically lpr. You
would change it to specify a particular queue if you need to print to a queue other
than the default. An example might be:
77
lpr -Pmypostscript
This field is greyed out if Output to file: is checked above.
Packet Range Select the packets to be printed, see Section 5.8, “The Packet Range frame”
Packet Format Select the output format of the packets to be printed. You can choose, how each
packet is printed, see Figure 5.19, “The "Packet Format" frame”
5.8. The Packet Range frame

The packet range frame is a part of various output related dialog boxes. It provides options to select which
packets should be processed by the output function.
Figure 5.18. The "Packet Range" frame
If the Captured button is set (default), all packets from the selected rule will be processed. If the Displayed
button is set, only the currently displayed packets are taken into account to the selected rule.
• All packets will process all packets.
• Selected packet only process only the selected packet.
• Marked packets only process only the marked packets.
• From first to last marked packet process the packets from the first to the last marked one.
• Specify a packet range process a user specified range of packets, e.g. specifying 5,10-15,20- will
process the packet number five, the packets from packet number ten to fifteen (inclusive) and every
packet from number twenty to the end of the capture.
5.9. The Packet Format frame

The packet format frame is a part of various output related dialog boxes. It provides options to select which
parts of a packet should be used for the output function.
Figure 5.19. The "Packet Format" frame
78
• Packet summary line enable the output of the summary line, just as in the "Packet List" pane.
• Packet details enable the output of the packet details tree.
• All collapsed the info from the "Packet Details" pane in "all collapsed" state.
• As displayed the info from the "Packet Details" pane in the current state.
• All expanded the info from the "Packet Details" pane in "all expanded" state.
• Packet bytes enable the output of the packet bytes, just as in the "Packet Bytes" pane.
• Each packet on a new page put each packet on a separate page (e.g. when saving/printing to a text
file, this will put a form feed character between the packets).
79
Chapter 6. Working with captured
packets
6.1. Viewing packets you have captured
Once you have captured some packets, or you have opened a previously saved capture file, you can view
the packets that are displayed in the packet list pane by simply clicking on a packet in the packet list pane,
which will bring up the selected packet in the tree view and byte view panes.
You can then expand any part of the tree view by clicking on the plus sign (the symbol itself may vary)
to the left of that part of the payload, and you can select individual fields by clicking on them in the tree
view pane. An example with a TCP packet selected is shown in Figure 6.1, “Wireshark with a TCP packet
selected for viewing”. It also has the Acknowledgment number in the TCP header selected, which shows
up in the byte view as the selected bytes.
Figure 6.1. Wireshark with a TCP packet selected for viewing
You can also select and view packets the same way, while Wireshark is capturing, if you selected "Update
list of packets in real time" in the Wireshark Capture Preferences dialog box.
In addition, you can view individual packets in a separate window as shown in Figure 6.2, “Viewing a
packet in a separate window”. Do this by selecting the packet in which you are interested in the packet list
pane, and then select "Show Packet in New Windows" from the Display menu. This allows you to easily
compare two or even more packets.
80
Working with captured packets
Figure 6.2. Viewing a packet in a separate window
6.2. Pop-up menus

You can bring up a pop-up menu over either the "Packet List" or "Packet Details" pane by clicking your
right mouse button at the corresponding pane.
6.2.1. Pop-up menu of the "Packet List" pane

Figure 6.3. Pop-up menu of the "Packet List" pane
The following table gives an overview of which functions are available in this pane, where to find the
corresponding function in the main menu, and a short description of each item.
81
Item Identical to main Description
menu's item:
Mark Packet Edit Mark/unmark a packet.
(toggle) Working with captured packets
Set Time Edit Set/reset a time reference.

Reference
Table 6.1. The menu items of the "Packet List" pop-up menu
(toggle)
-----
Apply as Filter Analyze Prepare and apply a display filter based on the currently selected
item.
Prepare a Filter Analyze Prepare a display filter based on the currently selected item.
Conversation - This menu item applies a display filter with the address
Filter information from the selected packet. E.g. the IP menu entry will
set a filter to show the traffic between the two IP addresses of the
current packet. XXX - add a new section describing this better.
Colorize - This menu item uses a display filter with the address information
Conversation from the selected packet to build a new colorizing rule.
SCTP - XXX - add an explanation of this.
Follow TCP Analyze Allows you to view all the data on a TCP stream between a pair
Stream of nodes.
Follow SSL Analyze Same as "Follow TCP Stream" but for SSL. XXX - add a new
Stream section describing this better.
-----
Copy/ Summary - Copy the summary fields as displayed to the clipboard, as tab-
(Text) separated text.
Copy/ Summary - Copy the summary fields as displayed to the clipboard, as
(CSV) comma-separated text.
Copy/ As Filter Prepare a display filter based on the currently selected item and
copy that filter to the clipboard.
Copy/ Bytes - Copy the packet bytes to the clipboard in hexdump-like format.
(Offset Hex Text)
Copy/ Bytes - Copy the packet bytes to the clipboard in hexdump-like format,
(Offset Hex) but without the text portion.
Copy/ Bytes - Copy the packet bytes to the clipboard as ASCII text, excluding
(Printable Text non-printable characters.
Only)
Copy/ Bytes (Hex - Copy the packet bytes to the clipboard as an unpunctuated list
Stream) of hex digits.
Copy/ Bytes - Copy the packet bytes to the clipboard as raw binary. The
(Binary Stream) data is stored in the clipboard as MIME-type "application/octet-
stream".
This option is not available in versions of Wireshark built using

GTK+ 1.x.
Export Selected File This menu item is the same as the File menu item of the same
Packet Bytes... name. It allows you to export raw packet bytes to a binary file.
-----
Decode As... Analyze Change or apply a new relation between two dissectors.
Print... File Print packets.
Show Packet in View Display the selected packet in a new window.
New Window
82
6.2.2. Pop-up menu of the "Packet Details" pane

Figure 6.4. Pop-up menu of the "Packet Details" pane
The following table gives an overview of which functions are available in this pane, where to find the
corresponding function in the main menu, and a short description of each item.
83
Copy/ Bytes - Copy the packet bytes to the clipboard in hexdump-like format;
(Offset Hex Text) similar to the Packet List Pane command, but copies only the
bytes relevant to the selected part of the tree (the bytes selected
in thecaptured
Working with Packet Bytes Pane).
packets
Copy/ Bytes - Copy the packet bytes to the clipboard in hexdump-like format,
(Offset Hex) but without the text portion; similar to the Packet List Pane
Table 6.2. The menu items of thecommand,
"PacketbutDetails" pop-up
copies only menu
the bytes relevant to the selected part
of the tree (the bytes selected in the Packet Bytes Pane).
Copy/ Bytes - Copy the packet bytes to the clipboard as ASCII text, excluding
(Printable Text non-printable characters; similar to the Packet List Pane
Only) command, but copies only the bytes relevant to the selected part
of the tree (the bytes selected in the Packet Bytes Pane).
Copy/ Bytes (Hex - Copy the packet bytes to the clipboard as an unpunctuated list of
Stream) hex digits; similar to the Packet List Pane command, but copies
only the bytes relevant to the selected part of the tree (the bytes
selected in the Packet Bytes Pane).
Copy/ Bytes - Copy the packet bytes to the clipboard as raw binary; similar to
(Binary Stream) the Packet List Pane command, but copies only the bytes relevant
to the selected part of the tree (the bytes selected in the Packet
Bytes Pane). The data is stored in the clipboard as MIME-type
"application/octet-stream".
This option is not available in versions of Wireshark built using

GTK+ 1.x.
Export Selected File This menu item is the same as the File menu item of the same
Packet Bytes... name. It allows you to export raw packet bytes to a binary file.
-----
Apply as Filter Analyze Prepare and apply a display filter based on the currently selected
item.
Prepare a Filter Analyze Prepare a display filter based on the currently selected item.
Colorize with - Prepare a display filter based on the currently selected item and
Filter use it to prepare a new colorize rule.
Follow TCP Analyze Allows you to view all the data on a TCP stream between a pair
Stream of nodes.
Follow SSL Analyze Same as "Follow TCP Stream" but for SSL. XXX - add a new
Stream section describing this better.
-----
Wiki Protocol - Show the wiki page corresponding to the currently selected
Page protocol in your web browser.
Filter Field - Show the filter field reference web page corresponding to the
Reference currently selected protocol in your web browser.
Protocol - The menu item takes you to the properties dialog and selects
Preferences... the page corresponding to the protocol if there are properties
associated with the highlighted field. More information on
preferences can be found in Figure 10.8, “The preferences dialog
box”.
-----
Decode As... Analyze Change or apply a new relation between two dissectors.
Resolve Name View Causes a name resolution to be performed for the selected packet,
but NOT every packet in the capture.
Go to Go If the selected field has a corresponding packet, go to it.
Corresponding Corresponding packets will usually be a request/response packet
Packet pair or such.
84
6.3. Filtering packets while viewing

Wireshark has two filtering languages: One used when capturing packets, and one used when displaying
packets. In this section we explore that second type of filter: Display filters. The first one has already been
dealt with in Section 4.10, “Filtering while capturing”.
Display filters allow you to concentrate on the packets you are interested in while hiding the currently
uninteresting ones. They allow you to select packets by:
• Protocol
• The presence of a field
• The values of fields
• A comparison between fields
• ... and a lot more!
To select packets based on protocol type, simply type the protocol in which you are interested in the Filter:
field in the filter toolbar of the Wireshark window and press enter to initiate the filter. Figure 6.5, “Filtering
on the TCP protocol” shows an example of what happens when you type tcp in the filter field.
Note!
All protocol and field names are entered in lowercase. Also, don't forget to press enter after
entering the filter expression.
Figure 6.5. Filtering on the TCP protocol
85
As you might have noticed, only packets of the TCP protocol are displayed now (e.g. packets 1-10 are
hidden). The packet numbering will remain as before, so the first packet shown is now packet number 11.
Note!
When using a display filter, all packets remain in the capture file. The display filter only
changes the display of the capture file but not its content!
You can filter on any protocol that Wireshark understands. You can also filter on any field that a dissector
adds to the tree view, but only if the dissector has added an abbreviation for the field. A list of such fields
is available in Wireshark in the Add Expression... dialog box. You can find more information on the Add
Expression... dialog box in Section 6.5, “The "Filter Expression" dialog box”.
For example, to narrow the packet list pane down to only those packets to or from the IP address
192.168.0.1, use ip.addr==192.168.0.1.
Note!
To remove the filter, click on the Clear button to the right of the filter field.
6.4. Building display filter expressions

Wireshark provides a simple but powerful display filter language that allows you to build quite complex
filter expressions. You can compare values in packets as well as combine expressions into more specific
expressions. The following sections provide more information on doing this.
Tip!
You will find a lot of Display Filter examples at the Wireshark Wiki Display Filter page
at http://wiki.wireshark.org/DisplayFilters.
6.4.1. Display filter fields

Every field in the packet details pane can be used as a filter string, this will result in showing only the
packets where this field exists. For example: the filter string: tcp will show all packets containing the tcp
protocol.
There is a complete list of all filter fields available through the menu item "Help/Supported Protocols" in
the page "Display Filter Fields" of the Supported Protocols dialog.
XXX - add some more info here and a link to the statusbar info.
6.4.2. Comparing values

You can build display filters that compare values using a number of different comparison operators. They
are shown in Table 6.3, “Display Filter comparison operators”.
Tip!
You can use English and C-like terms in the same way, they can even be mixed in a filter
string!
86
Table 6.3. Display Filter comparison operators
English C-like Description and example

eq == Equal
ip.src==10.0.0.5
ne != Not equal
ip.src!=10.0.0.5
gt > Greater than
frame.len > 10
lt < Less than
frame.len < 128

ge >= Greater than or equal to
frame.len ge 0x100
le <= Less than or equal to
frame.len <= 0x20
In addition, all protocol fields are typed. Table 6.4, “Display Filter Field Types” provides a list of the types
and example of how to express them.
87
Table 6.4. Display Filter Field Types
Type Example
Unsigned integer (8-bit, 16-bit, 24-bit, 32-bit) You can express integers in decimal, octal, or
hexadecimal. The following display filters are
equivalent:
ip.len le 1500
ip.len le 02734
ip.len le 0x436
Signed integer (8-bit, 16-bit, 24-bit, 32-bit)

Boolean A boolean field is present in the protocol decode
only if its value is true. For example, tcp.flags.syn is
present, and thus true, only if the SYN flag is present
in a TCP segment header.
Thus the filter expression tcp.flags.syn will select

only those packets for which this flag exists, that is,
TCP segments where the segment header contains
the SYN flag. Similarly, to find source-routed token
ring packets, use a filter expression of tr.sr.
Ethernet address (6 bytes) Separators can be a colon (:), dot (.) or dash (-) and
can have one or two bytes between separators:
eth.dst == ff:ff:ff:ff:ff:ff
eth.dst == ff-ff-ff-ff-ff-ff
eth.dst == ffff.ffff.ffff
IPv4 address ip.addr == 192.168.0.1
Classless InterDomain Routing (CIDR) notation

can be used to test if an IPv4 address is in a certain
subnet. For example, this display filter will find all
packets in the 129.111 Class-B network:
ip.addr == 129.111.0.0/16
IPv6 address ipv6.addr == ::1
IPX address ipx.addr == 00000000.ffffffffffff
String (text) http.request.uri == "http://www.wireshark.org/"
6.4.3. Combining expressions

You can combine filter expressions in Wireshark using the logical operators shown in Table 6.5, “Display
Filter Logical Operations”
88
Table 6.5. Display Filter Logical Operations
English C-like Description and example

and && Logical AND
ip.src==10.0.0.5 and tcp.flags.fin

or || Logical OR
ip.scr==10.0.0.5 or ip.src==192.1.1.1
xor ^^ Logical XOR
tr.dst[0:3] == 0.6.29 xor tr.src[0:3] == 0.6.29

not ! Logical NOT
not llc
[...] Substring Operator
Wireshark allows you to select subsequences of a sequence in rather elaborate

ways. After a label you can place a pair of brackets [] containing a comma
separated list of range specifiers.
eth.src[0:3] == 00:00:83
The example above uses the n:m format to specify a single range. In this case n
is the beginning offset and m is the length of the range being specified.
eth.src[1-2] == 00:83
The example above uses the n-m format to specify a single range. In this case n
is the beginning offset and m is the ending offset.
eth.src[:4] == 00:00:83:00
The example above uses the :m format, which takes everything from the
beginning of a sequence to offset m. It is equivalent to 0:m
eth.src[4:] == 20:20
The example above uses the n: format, which takes everything from offset n to
the end of the sequence.
eth.src[2] == 83
The example above uses the n format to specify a single range. In this case the
element in the sequence at offset n is selected. This is equivalent to n:1.
eth.src[0:3,1-2,:4,4:,2] ==
00:00:83:00:83:00:00:83:00:20:20:83
Wireshark allows you to string together single ranges in a comma separated list
to form compound ranges as shown above.
89
6.4.4. A common mistake

Warning!
Using the != operator on combined expressions like: eth.addr, ip.addr, tcp.port, udp.port and
alike will probably not work as expected!
Often people use a filter string to display something like ip.addr == 1.2.3.4 which will display all packets
containing the IP address 1.2.3.4.
Then they use ip.addr != 1.2.3.4 to see all packets not containing the IP address 1.2.3.4 in it. Unfortunately,
this does not do the expected.
Instead, that expression will even be true for packets where either source or destination IP address equals
1.2.3.4. The reason for this, is that the expression ip.addr != 1.2.3.4 must be read as "the packet contains
a field named ip.addr with a value different from 1.2.3.4". As an IP datagram contains both a source and a
destination address, the expression will evaluate to true whenever at least one of the two addresses differs
from 1.2.3.4.
If you want to filter out all packets containing IP datagrams to or from IP address 1.2.3.4, then the correct
filter is !(ip.addr == 1.2.3.4) as it reads "show me all the packets for which it is not true that a field named
ip.addr exists with a value of 1.2.3.4", or in other words, "filter out all packets for which there are no
occurrences of a field named ip.addr with the value 1.2.3.4".
6.5. The "Filter Expression" dialog box

When you are accustomed to Wireshark's filtering system and know what labels you wish to use in your
filters it can be very quick to simply type a filter string. However if you are new to Wireshark or are
working with a slightly unfamiliar protocol it can be very confusing to try to figure out what to type. The
Filter Expression dialog box helps with this.
Tip!
The "Filter Expression" dialog box is an excellent way to learn how to write Wireshark
display filter strings.
90
Figure 6.6. The "Filter Expression" dialog box
When you first bring up the Filter Expression dialog box you are shown a tree list of field names, organized
by protocol, and a box for selecting a relation.
Field Name Select a protocol field from the protocol field tree. Every protocol with filterable fields
is listed at the top level. (You can search for a particular protocol entry by entering the
first few letters of the protocol name). By clicking on the "+" next to a protocol name
you can get a list of the field names available for filtering for that protocol.
Relation Select a relation from the list of available relation. The is present is a unary relation
which is true if the selected field is present in a packet. All other listed relations are binary
relations which require additional data (e.g. a Value to match) to complete.
When you select a field from the field name list and select a binary relation (such as the equality relation
==) you will be given the opportunity to enter a value, and possibly some range information.
Value You may enter an appropriate value in the Value text box. The Value will also
indicate the type of value for the field name you have selected (like character
string).
Predefined values Some of the protocol fields have predefined values available, much like
enum's in C. If the selected protocol field has such values defined, you can
choose one of them here.
Range XXX - add an explanation here!
OK When you have built a satisfactory expression click OK and a filter string will
be built for you.
Cancel You can leave the Add Expression... dialog box without any effect by clicking
the Cancel button.
6.6. Defining and saving filters

You can define filters with Wireshark and give them labels for later use. This can save time in remembering
and retyping some of the more complex filters you use.
91
To define a new filter or edit an existing one, select the Capture Filters... menu item from the Capture
menu or the Display Filters... menu item from the Analyze menu. Wireshark will then pop up the Filters
dialog as shown in Figure 6.7, “The "Capture Filters" and "Display Filters" dialog boxes”.
Note!
The mechanisms for defining and saving capture filters and display filters are almost
identical. So both will be described here, differences between these two will be marked as
such.
Warning!
You must use Save to save your filters permanently. Ok or Apply will not save the filters,
so they will be lost when you close Wireshark.
Figure 6.7. The "Capture Filters" and "Display Filters" dialog boxes
New This button adds a new filter to the list of filters. The currently entered values
from Filter name and Filter string will be used. If any of these fields are empty,
it will be set to "new".
Delete This button deletes the selected filter. It will be greyed out, if no filter is
selected.
Filter You can select a filter from this list (which will fill in the filter name and filter
string in the fields down at the bottom of the dialog box).
Filter name: You can change the name of the currently selected filter here.
Note!
The filter name will only be used in this dialog to identify the
filter for your convenience, it will not be used elsewhere. You
can add multiple filters with the same name, but this is not very
useful.
92
Filter string: You can change the filter string of the currently selected filter here. Display
Filter only: the string will be syntax checked while you are typing.
Add Expression... Display Filter only: This button brings up the Add Expression dialog box
which assists in building filter strings. You can find more information about
the Add Expression dialog in Section 6.5, “The "Filter Expression" dialog
box”
OK Display Filter only: This button applies the selected filter to the current display
and closes the dialog.
Apply Display Filter only: This button applies the selected filter to the current
display, and keeps the dialog open.
Save Save the current settings in this dialog. The file location and format is
explained in Appendix A, Files and Folders.
Close Close this dialog. This will discard unsaved settings.
6.7. Defining and saving filter macros

You can define filter macros with Wireshark and give them labels for later use. This can save time in
remembering and retyping some of the more complex filters you use.
XXX - add an explanation of this.
6.8. Finding packets

You can easily find packets once you have captured some packets or have read in a previously saved
capture file. Simply select the Find Packet... menu item from the Edit menu. Wireshark will pop up the
dialog box shown in Figure 6.8, “The "Find Packet" dialog box”.
6.8.1. The "Find Packet" dialog box

Figure 6.8. The "Find Packet" dialog box
You might first select the kind of thing to search for:
• Display filter
Simply enter a display filter string into the Filter: field, select a direction, and click on OK.
For example, to find the three way handshake for a connection from host 192.168.0.1, use the following
filter string:
93
ip.src==192.168.0.1 and tcp.flags.syn==1
For more details on display filters, see Section 6.3, “Filtering packets while viewing”
• Hex Value
Search for a specific byte sequence in the packet data.
For example, use "00:00" to find the next packet including two null bytes in the packet data.
• String
Find a string in the packet data, with various options.
The value to be found will be syntax checked while you type it in. If the syntax check of your value
succeeds, the background of the entry field will turn green, if it fails, it will turn red.
You can choose the search direction:
• Up
Search upwards in the packet list (decreasing packet numbers).
• Down
Search downwards in the packet list (increasing packet numbers).
6.8.2. The "Find Next" command

"Find Next" will continue searching with the same options used in the last "Find Packet".
6.8.3. The "Find Previous" command

"Find Previous" will do the same thing as "Find Next", but with reverse search direction.
6.9. Go to a specific packet

You can easily jump to specific packets with one of the menu items in the Go menu.
6.9.1. The "Go Back" command

Go back in the packet history, works much like the page history in current web browsers.
6.9.2. The "Go Forward" command

Go forward in the packet history, works much like the page history in current web browsers.
6.9.3. The "Go to Packet" dialog box

Figure 6.9. The "Go To Packet" dialog box
94
This dialog box will let you enter a packet number. When you press OK, Wireshark will jump to that
packet.
6.9.4. The "Go to Corresponding Packet" command

If a protocol field is selected which points to another packet in the capture file, this command will jump
to that packet.
Note!
As these protocol fields now work like links (just as in your Web browser), it's easier to
simply double-click on the field to jump to the corresponding field.
6.9.5. The "Go to First Packet" command

This command will simply jump to the first packet displayed.
6.9.6. The "Go to Last Packet" command

This command will simply jump to the last packet displayed.
6.10. Marking packets

You can mark packets in the "Packet List" pane. A marked packet will be shown with black background,
regardless of the coloring rules set. Marking a packet can be useful to find it later while analyzing in a
large capture file.
Warning!
The packet marks are not stored in the capture file or anywhere else, so all packet marks will
be lost if you close the capture file.
You can use packet marking to control the output of packets when saving/exporting/printing. To do so, an
option in the packet range is available, see Section 5.8, “The Packet Range frame”.
There are three functions to manipulate the marked state of a packet:
• Mark packet (toggle) toggles the marked state of a single packet.
• Mark all displayed packets set the mark state of all displayed packets.
• Unmark all packets reset the mark state of all packets.
These mark functions are available from the "Edit" menu, and the "Mark packet (toggle)" function is also
available from the pop-up menu of the "Packet List" pane.
6.11. Ignoring packets

You can ignore packets in the "Packet List" pane. Wireshark will then pretend that this packets does not
exist in the capture file. An ignored packet will be shown with white background and gray foreground,
regardless of the coloring rules set.
95
Warning!
The packet ignored marks are not stored in the capture file or anywhere else, so all packet
ignored marks will be lost if you close the capture file.
There are three functions to manipulate the ignored state of a packet:
• Ignore packet (toggle) toggles the ignored state of a single packet.
• Ignore all displayed packets set the ignored state of all displayed packets.
• Un-Ignore all packets reset the ignored state of all packets.
These ignore functions are available from the "Edit" menu, and the "Ignore packet (toggle)" function is
also available from the pop-up menu of the "Packet List" pane.
6.12. Time display formats and time references

While packets are captured, each packet is timestamped. These timestamps will be saved to the capture
file, so they will be available for later analysis.
A detailed description of timestamps, timezones and alike can be found at: Section 7.4, “Time Stamps”.
The timestamp presentation format and the precision in the packet list can be chosen using the View menu,
see Figure 3.5, “The "View" Menu”.
The available presentation formats are:
• Date and Time of Day: 1970-01-01 01:02:03.123456 The absolute date and time of the day when
the packet was captured.
• Time of Day: 01:02:03.123456 The absolute time of the day when the packet was captured.
• Seconds Since Beginning of Capture: 123.123456 The time relative to the start of the capture file or
the first "Time Reference" before this packet (see Section 6.12.1, “Packet time referencing”).
• Seconds Since Previous Captured Packet: 1.123456 The time relative to the previous captured
packet.
• Seconds Since Previous Displayed Packet: 1.123456 The time relative to the previous displayed
packet.
• Seconds Since Epoch (1970-01-01): 1234567890.123456 The time relative to epoch (midnight UTC
of January 1, 1970).
The available precisions (aka. the number of displayed decimal places) are:
• Automatic The timestamp precision of the loaded capture file format will be used (the default).
• Seconds, Deciseconds, Centiseconds, Milliseconds, Microseconds or Nanoseconds The timestamp

precision will be forced to the given setting. If the actually available precision is smaller, zeros will be
appended. If the precision is larger, the remaining decimal places will be cut off.
Precision example: If you have a timestamp and it's displayed using, "Seconds Since Previous Packet", :
the value might be 1.123456. This will be displayed using the "Automatic" setting for libpcap files (which
is microseconds). If you use Seconds it would show simply 1 and if you use Nanoseconds it shows
1.123456000.
96
6.12.1. Packet time referencing

The user can set time references to packets. A time reference is the starting point for all subsequent packet
time calculations. It will be useful, if you want to see the time values relative to a special packet, e.g. the
start of a new request. It's possible to set multiple time references in the capture file.
Warning!
The time references will not be saved permanently and will be lost when you close the capture
file.
Note!
Time referencing will only be useful, if the time display format is set to "Seconds Since
Beginning of Capture". If one of the other time display formats are used, time referencing
will have no effect (and will make no sense either).
To work with time references, choose one of the "Time Reference" items in the "Edit" menu , see
Section 3.6, “The "Edit" menu”, or from the pop-up menu of the "Packet List" pane.
• Set Time Reference (toggle) Toggles the time reference state of the currently selected packet to on
or off.
• Find Next Find the next time referenced packet in the "Packet List" pane.
• Find Previous Find the previous time referenced packet in the "Packet List" pane.
Figure 6.10. Wireshark showing a time referenced packet
97
A time referenced packet will be marked with the string *REF* in the Time column (see packet number
10). All subsequent packets will show the time since the last time reference.
98
Chapter 7. Advanced Topics
7.1. Introduction
In this chapter some of the advanced features of Wireshark will be described.
7.2. Following TCP streams

If you are working with TCP based protocols it can be very helpful to see the data from a TCP stream in
the way that the application layer sees it. Perhaps you are looking for passwords in a Telnet stream, or you
are trying to make sense of a data stream. Maybe you just need a display filter to show only the packets of
that TCP stream. If so, Wireshark's ability to follow a TCP stream will be useful to you.
Simply select a TCP packet in the packet list of the stream/connection you are interested in and then select
the Follow TCP Stream menu item from the Wireshark Tools menu (or use the context menu in the packet
list). Wireshark will set an appropriate display filter and pop up a dialog box with all the data from the
TCP stream laid out in order, as shown in Figure 7.1, “The "Follow TCP Stream" dialog box”.
Note!
It is worthwhile noting that Follow TCP Stream installs a display filter to select all the packets
in the TCP stream you have selected.
7.2.1. The "Follow TCP Stream" dialog box

Figure 7.1. The "Follow TCP Stream" dialog box
99
Advanced Topics
The stream content is displayed in the same sequence as it appeared on the network. Traffic from A to B
is marked in red, while traffic from B to A is marked in blue. If you like, you can change these colors in
the Edit/Preferences "Colors" page.
Non-printable characters will be replaced by dots. XXX - What about line wrapping (maximum line length)
and CRNL conversions?
The stream content won't be updated while doing a live capture. To get the latest content you'll have to
reopen the dialog.
You can choose from the following actions:
1. Save As: Save the stream data in the currently selected format.
2. Print: Print the stream data in the currently selected format.
3. Direction: Choose the stream direction to be displayed ("Entire conversation", "data from A to B
only" or "data from B to A only").
4. Filter out this stream: Apply a display filter removing the current TCP stream data from the display.
5. Close: Close this dialog box, leaving the current display filter in effect.
You can choose to view the data in one of the following formats:
1. ASCII: In this view you see the data from each direction in ASCII. Obviously best for ASCII based
protocols, e.g. HTTP.
2. EBCDIC: For the big-iron freaks out there.
3. HEX Dump: This allows you to see all the data. This will require a lot of screen space and is best
used with binary protocols.
4. C Arrays: This allows you to import the stream data into your own C program.
5. Raw: This allows you to load the unaltered stream data into a different program for further
examination. The display will look the same as the ASCII setting, but "Save As" will result in a
binary file.
7.3. Expert Infos

The expert infos is a kind of log of the anomalies found by Wireshark in a capture file.
The general idea behind the following "Expert Info" is to have a better display of "uncommon" or just
notable network behaviour. This way, both novice and expert users will hopefully find probable network
problems a lot faster, compared to scanning the packet list "manually" .
Expert infos are only a hint!

Take expert infos as a hint what's worth looking at, but not more. For example: The absence
of expert infos doesn't necessarily mean everything is ok!
The amount of expert infos largely depends on the protocol

being used!
While some common protocols like TCP/IP will show detailed expert infos, most other
protocols currently won't show any expert infos at all.
100
Advanced Topics
The following will first describe the components of a single expert info, then the User Interface.
7.3.1. Expert Info Entries

Each expert info will contain the following things which will be described in detail below:
Table 7.1. Some example expert infos

Packet # Severity Group Protocol Summary
1 Note Sequence TCP Duplicate
ACK (#1)
2 Chat Sequence TCP Connection
reset (RST)
8 Note Sequence TCP Keep-Alive
9 Warn Sequence TCP Fast
retransmission
(suspected)
7.3.1.1. Severity
Every expert info has a specific severity level. The following severity levels are used, in parentheses are
the colors in which the items will be marked in the GUI:
• Chat (grey): information about usual workflow, e.g. a TCP packet with the SYN flag set
• Note (cyan): notable things, e.g. an application returned an "usual" error code like HTTP 404
• Warn (yellow): warning, e.g. application returned an "unusual" error code like a connection problem
• Error (red): serious problem, e.g. [Malformed Packet]
7.3.1.2. Group
There are some common groups of expert infos. The following are currently implemented:
• Checksum: a checksum was invalid
• Sequence: protocol sequence suspicious, e.g. sequence wasn't continuous or a retransmission was
detected or ...
• Response Code: problem with application response code, e.g. HTTP 404 page not found
• Request Code: an application request (e.g. File Handle == x), usually Chat level
• Undecoded: dissector incomplete or data can't be decoded for other reasons
• Reassemble: problems while reassembling, e.g. not all fragments were available or an exception
happened while reassembling
• Protocol: violation of protocol specs (e.g. invalid field values or illegal lengths), dissection of this
packet is probably continued
• Malformed: malformed packet or dissector has a bug, dissection of this packet aborted
• Debug: debugging (should not occur in release versions)
It's possible that more such group values will be added in the future ...
101
Advanced Topics
7.3.1.3. Protocol
The protocol in which the expert info was caused.
7.3.1.4. Summary
Each expert info will also have a short additional text with some further explanation.
7.3.2. "Expert Info Composite" dialog

From the main menu you can open the expert info dialog, using: "Analyze/Expert Info Composite"
XXX - "Analyze/Expert Info" also exists but is subject to removal and therefore not explained here.
XXX - add explanation of the dialogs context menu.
7.3.2.1. Errors / Warnings / Notes / Chats tabs

An easy and quick way to find the most interesting infos (rather than using the Details tab), is to have
a look at the separate tabs for each severity level. As the tab label also contains the number of existing
entries, it's easy to find the tab with the most important entries.
There are usually a lot of identical expert infos only differing in the packet number. These identical infos
will be combined into a single line - with a count column showing how often they appeared in the capture
file. Clicking on the plus sign shows the individual packet numbers in a tree view.
7.3.2.2. Details tab

The Details tab provides the expert infos in a "log like" view, each entry on its own line (much like the
packet list). As the amount of expert infos for a capture file can easily become very large, getting an idea
of the interesting infos with this view can take quite a while. The advantage of this tab is to have all entries
in the sequence as they appeared, this is sometimes a help to pinpoint problems.
7.3.3. "Colorized" Protocol Details Tree
102
Advanced Topics
The protocol field causing an expert info is colorized, e.g. uses a cyan background for a note severity
level. This color is propagated to the toplevel protocol item in the tree, so it's easy to find the field that
caused the expert info.
For the example screenshot above, the IP "Time to live" value is very low (only 1), so the corresponding
protocol field is marked with a cyan background. To easier find that item in the packet tree, the IP protocol
toplevel item is marked cyan as well.
7.3.4. "Expert" Packet List Column (optional)
An optional "Expert Info Severity" packet list column is available (since SVN 22387 -> 0.99.7), that
displays the most significant severity of a packet, or stays empty if everything seems ok. This column
is not displayed by default, but can be easily added using the Preferences Columns page described in
Section 10.5, “Preferences”.
7.4. Time Stamps

Time stamps, their precisions and all that can be quite confusing. This section will provide you with
information about what's going on while Wireshark processes time stamps.
While packets are captured, each packet is time stamped as it comes in. These time stamps will be saved
to the capture file, so they also will be available for (later) analysis.
So where do these time stamps come from? While capturing, Wireshark gets the time stamps from the
libpcap (WinPcap) library, which in turn gets them from the operating system kernel. If the capture data
is loaded from a capture file, Wireshark obviously gets the data from that file.
7.4.1. Wireshark internals

The internal format that Wireshark uses to keep a packet time stamp consists of the date (in days since
1.1.1970) and the time of day (in nanoseconds since midnight). You can adjust the way Wireshark displays
the time stamp data in the packet list, see the "Time Display Format" item in the Section 3.7, “The "View"
menu” for details.
While reading or writing capture files, Wireshark converts the time stamp data between the capture file
format and the internal format as required.
While capturing, Wireshark uses the libpcap (WinPcap) capture library which supports microsecond
resolution. Unless you are working with specialized capturing hardware, this resolution should be
adequate.
103
Advanced Topics
7.4.2. Capture file formats

Every capture file format that Wireshark knows supports time stamps. The time stamp precision supported
by a specific capture file format differs widely and varies from one second "0" to one nanosecond
"0.123456789". Most file formats store the time stamps with a fixed precision (e.g. microseconds), while
some file formats are even capable of storing the time stamp precision itself (whatever the benefit may be).
The common libpcap capture file format that is used by Wireshark (and a lot of other tools) supports a
fixed microsecond resolution "0.123456" only.
Note!
Writing data into a capture file format that doesn't provide the capability to store the
actual precision will lead to loss of information. Example: If you load a capture file
with nanosecond resolution and store the capture data to a libpcap file (with microsecond
resolution) Wireshark obviously must reduce the precision from nanosecond to microsecond.
7.4.3. Accuracy
It's often asked: "Which time stamp accuracy is provided by Wireshark?". Well, Wireshark doesn't create
any time stamps itself but simply gets them from "somewhere else" and displays them. So accuracy will
depend on the capture system (operating system, performance, ...) that you use. Because of this, the above
question is difficult to answer in a general way.
Note!
USB connected network adapters often provide a very bad time stamp accuracy. The
incoming packets have to take "a long and winding road" to travel through the USB cable
until they actually reach the kernel. As the incoming packets are time stamped when they are
processed by the kernel, this time stamping mechanism becomes very inaccurate.
Conclusion: don't use USB connected NIC's when you need precise time stamp accuracy!
(XXX - are there any such NIC's that generate time stamps on the USB hardware?)
7.5. Time Zones

If you travel across the planet, time zones can be confusing. If you get a capture file from somewhere
around the world time zones can even be a lot more confusing ;-)
First of all, there are two reasons why you may not need to think about time zones at all:
• You are only interested in the time differences between the packet time stamps and don't need to know
the exact date and time of the captured packets (which is often the case).
• You don't get capture files from different time zones than your own, so there are simply no time zone
problems. For example: everyone in your team is working in the same time zone as yourself.
104
Advanced Topics
What are time zones?
People expect that the time reflects the sunset. Dawn should be in the morning maybe around 06:00
and dusk in the evening maybe at 20:00. These times will obviously vary depending on the season.
It would be very confusing if everyone on earth would use the same global time as this would
correspond to the sunset only at a small part of the world.
For that reason, the earth is split into several different time zones, each zone with a local time that
corresponds to the local sunset.
The time zone's base time is UTC (Coordinated Universal Time) or Zulu Time (military and
aviation). The older term GMT (Greenwich Mean Time) shouldn't be used as it is slightly incorrect
(up to 0.9 seconds difference to UTC). The UTC base time equals to 0 (based at Greenwich, England)
and all time zones have an offset to UTC between -12 to +14 hours!
For example: If you live in Berlin you are in a time zone one hour earlier than UTC, so you are in
time zone "+1" (time difference in hours compared to UTC). If it's 3 o'clock in Berlin it's 2 o'clock
in UTC "at the same moment".
Be aware that at a few places on earth don't use time zones with even hour offsets (e.g. New Delhi
uses UTC+05:30)!
Further information can be found at: http://en.wikipedia.org/wiki/Time_zone and http://

en.wikipedia.org/wiki/Coordinated_Universal_Time.
What is daylight saving time (DST)?
Daylight Saving Time (DST), also known as Summer Time, is intended to "save" some daylight
during the summer months. To do this, a lot of countries (but not all!) add a DST hour to the already
existing UTC offset. So you may need to take another hour (or in very rare cases even two hours!)
difference into your "time zone calculations".
Unfortunately, the date at which DST actually takes effect is different throughout the world. You
may also note, that the northern and southern hemispheres have opposite DST's (e.g. while it's
summer in Europe it's winter in Australia).
Keep in mind: UTC remains the same all year around, regardless of DST!
Further information can be found at: http://en.wikipedia.org/wiki/Daylight_saving.
Further time zone and DST information can be found at: http://wwp.greenwichmeantime.com/ and http://
www.timeanddate.com/worldclock/.
7.5.1. Set your computer's time correctly!

If you work with people around the world, it's very helpful to set your computer's time and time zone right.
You should set your computers time and time zone in the correct sequence:
1. Set your time zone to your current location
2. Set your computer's clock to the local time
This way you will tell your computer both the local time and also the time offset to UTC.
105
Advanced Topics
Tip!
If you travel around the world, it's an often made mistake to adjust the hours of your computer
clock to the local time. Don't adjust the hours but your time zone setting instead! For your
computer, the time is essentially the same as before, you are simply in a different time zone
with a different local time!
Tip!
You can use the Network Time Protocol (NTP) to automatically adjust your computer to the
correct time, by synchronizing it to Internet NTP clock servers. NTP clients are available for
all operating systems that Wireshark supports (and for a lot more), for examples see: http://
www.ntp.org/.
7.5.2. Wireshark and Time Zones

So what's the relationship between Wireshark and time zones anyway?
Wireshark's native capture file format (libpcap format), and some other capture file formats, such as
the Windows Sniffer, EtherPeek, AiroPeek, and Sun snoop formats, save the arrival time of packets as
UTC values. UN*X systems, and "Windows NT based" systems (Windows NT 4.0, 2000, XP, Server
2003, Vista, Server 2008) represent time internally as UTC. When Wireshark is capturing, no conversion
is necessary. However, if the system time zone is not set correctly, the system's UTC time might not
be correctly set even if the system clock appears to display correct local time. "Windows 9x based"
systems (Windows 95, Windows 98, Windows Me) represent time internally as local time. When capturing,
WinPcap has to convert the time to UTC before supplying it to Wireshark. If the system's time zone is not
set correctly, that conversion will not be done correctly.
Other capture file formats, such as the Microsoft Network Monitor, DOS-based Sniffer, and Network
Instruments Observer formats, save the arrival time of packets as local time values.
Internally to Wireshark, time stamps are represented in UTC; this means that, when reading capture files
that save the arrival time of packets as local time values, Wireshark must convert those local time values
to UTC values.
Wireshark in turn will display the time stamps always in local time. The displaying computer will convert
them from UTC to local time and displays this (local) time. For capture files saving the arrival time of
packets as UTC values, this means that the arrival time will be displayed as the local time in your time
zone, which might not be the same as the arrival time in the time zone in which the packet was captured.
For capture files saving the arrival time of packets as local time values, the conversion to UTC will be
done using your time zone's offset from UTC and DST rules, which means the conversion will not be done
correctly; the conversion back to local time for display might undo this correctly, in which case the arrival
time will be displayed as the arrival time in which the packet was captured.
Table 7.2. Time zone examples for UTC arrival times (without DST)
Los Angeles New York Madrid London Berlin Tokyo
Capture File 10:00 10:00 10:00 10:00 10:00 10:00
(UTC)
Local Offset -8 -5 -1 0 +1 +9
to UTC
Displayed 02:00 05:00 09:00 10:00 11:00 19:00
Time (Local
Time)
106
Advanced Topics
An example: Let's assume that someone in Los Angeles captured a packet with Wireshark at exactly 2
o'clock local time and sends you this capture file. The capture file's time stamp will be represented in UTC
as 10 o'clock. You are located in Berlin and will see 11 o'clock on your Wireshark display.
Now you have a phone call, video conference or Internet meeting with that one to talk about that capture
file. As you are both looking at the displayed time on your local computers, the one in Los Angeles still
sees 2 o'clock but you in Berlin will see 11 o'clock. The time displays are different as both Wireshark
displays will show the (different) local times at the same point in time.
Conclusion: You may not bother about the date/time of the time stamp you currently look at, unless you
must make sure that the date/time is as expected. So, if you get a capture file from a different time zone and/
or DST, you'll have to find out the time zone/DST difference between the two local times and "mentally
adjust" the time stamps accordingly. In any case, make sure that every computer in question has the correct
time and time zone setting.
7.6. Packet Reassembling

7.6.1. What is it?
Network protocols often need to transport large chunks of data, which are complete in themselves, e.g.
when transferring a file. The underlying protocol might not be able to handle that chunk size (e.g. limitation
of the network packet size), or is stream-based like TCP, which doesn't know data chunks at all.
In that case the network protocol has to handle the chunk boundaries itself and (if required) spread the
data over multiple packets. It obviously also needs a mechanism to determine the chunk boundaries on
the receiving side.
Tip!
Wireshark calls this mechanism reassembling, although a specific protocol specification
might use a different term for this (e.g. desegmentation, defragmentation, ...).
7.6.2. How Wireshark handles it

For some of the network protocols Wireshark knows of, a mechanism is implemented to find, decode and
display these chunks of data. Wireshark will try to find the corresponding packets of this chunk, and will
show the combined data as additional pages in the "Packet Bytes" pane (for information about this pane,
see Section 3.19, “The "Packet Bytes" pane”).
Figure 7.2. The "Packet Bytes" pane with a reassembled tab
Note!
Reassembling might take place at several protocol layers, so it's possible that multiple tabs
in the "Packet Bytes" pane appear.
Note!
You will find the reassembled data in the last packet of the chunk.
107
Advanced Topics
An example: In a HTTP GET response, the requested data (e.g. an HTML page) is returned. Wireshark
will show the hex dump of the data in a new tab "Uncompressed entity body" in the "Packet Bytes" pane.
Reassembling is enabled in the preferences by default. The defaults were changed from disabled to enabled
in September 2005. If you created your preference settings before this date, you might look if reassembling
is actually enabled, as it can be extremely helpful while analyzing network packets.
The enabling or disabling of the reassemble settings of a protocol typically requires two things:
1. the lower level protocol (e.g., TCP) must support reassembly. Often this reassembly can be enabled
or disabled via the protocol preferences.
2. the higher level protocol (e.g., HTTP) must use the reassembly mechanism to reassemble fragmented
protocol data. This too can often be enabled or disabled via the protocol preferences.
The tooltip of the higher level protocol setting will notify you if and which lower level protocol setting
also has to be considered.
7.7. Name Resolution

Name resolution tries to resolve some of the numerical address values into a human readable format.
There are two possible ways to do these conversations, depending on the resolution to be done:
calling system/network services (like the gethostname function) and/or evaluate from Wireshark specific
configuration files. For details about the configuration files Wireshark uses for name resolution and alike,
see Appendix A, Files and Folders.
The name resolution feature can be en-/disabled separately for the protocol layers of the following sections.
7.7.1. Name Resolution drawbacks

Name resolution can be invaluable while working with Wireshark and may even save you hours of work.
Unfortunately, it also has its drawbacks.
• Name resolution will often fail. The name to be resolved might simply be unknown by the name
servers asked or the servers are just not available and the name is also not found in Wireshark's
configuration files.
• The resolved names are not stored in the capture file or somewhere else. So the resolved names
might not be available if you open the capture file later or on a different machine. Each time you open a
capture file it may look "slightly different", maybe simply because you can't connect to a name server
(which you could connect before).
• DNS may add additional packets to your capture file. You may see packets to/from your machine
in your capture file, which are caused by name resolution network services of the machine Wireshark
captures from. XXX - are there any other such packets than DNS ones?
• Resolved DNS names are cached by Wireshark. This is required for acceptable performance.
However, if the name resolution information should change while Wireshark is running, Wireshark
won't notice a change to the name resolution information once it gets cached. If this information
changes while Wireshark is running, e.g. a new DHCP lease takes effect, Wireshark won't notice it.
XXX - is this true for all or only for DNS info?
Tip!
The name resolution in the packet list is done while the list is filled. If a name could be
resolved after a packet was added to the list, that former entry won't be changed. As the name
108
Advanced Topics
resolution results are cached, you can use "View/Reload" to rebuild the packet list, this time
with the correctly resolved names. However, this isn't possible while a capture is in progress.
7.7.2. Ethernet name resolution (MAC layer)

Try to resolve an Ethernet MAC address (e.g. 00:09:5b:01:02:03) to something more "human readable".
ARP name resolution (system service): Wireshark will ask the operating system to convert an Ethernet
address to the corresponding IP address (e.g. 00:09:5b:01:02:03 -> 192.168.0.1).
Ethernet codes (ethers file): If the ARP name resolution failed, Wireshark tries to convert the Ethernet
address to a known device name, which has been assigned by the user using an ethers file (e.g.
00:09:5b:01:02:03 -> homerouter).
Ethernet manufacturer codes (manuf file): If neither ARP or ethers returns a result, Wireshark tries
to convert the first 3 bytes of an ethernet address to an abbreviated manufacturer name, which has been
assigned by the IEEE (e.g. 00:09:5b:01:02:03 -> Netgear_01:02:03).
7.7.3. IP name resolution (network layer)

Try to resolve an IP address (e.g. 216.239.37.99) to something more "human readable".
DNS/ADNS name resolution (system/library service): Wireshark will ask the operating system (or
the ADNS library), to convert an IP address to the hostname associated with it (e.g. 216.239.37.99 ->
www.1.google.com). The DNS service is using synchronous calls to the DNS server. So Wireshark will
stop responding until a response to a DNS request is returned. If possible, you might consider using the
ADNS library (which won't wait for a network response).
Warning!
Enabling network name resolution when your name server is unavailable may significantly
slow down Wireshark while it waits for all of the name server requests to time out. Use
ADNS in that case.
DNS vs. ADNS: here's a short comparison: Both mechanisms are used to convert an IP address to some
human readable (domain) name. The usual DNS call gethostname() will try to convert the address to a
name. To do this, it will first ask the systems hosts file (e.g. /etc/hosts) if it finds a matching entry. If that
fails, it will ask the configured DNS server(s) about the name.
So the real difference between DNS and ADNS comes when the system has to wait for the DNS server
about a name resolution. The system call gethostname() will wait until a name is resolved or an error
occurs. If the DNS server is unavailable, this might take quite a while (several seconds). The ADNS service
will work a bit differently. It will also ask the DNS server, but it won't wait for the answer. It will just
return to Wireshark in a very short amount of time. The actual (and the following) address fields won't
show the resolved name until the ADNS call returned. As mentioned above, the values get cached, so you
can use View/Reload to "update" these fields to show the resolved values.
hosts name resolution (hosts file): If DNS name resolution failed, Wireshark will try to convert an IP
address to the hostname associated with it, using a hosts file provided by the user (e.g. 216.239.37.99 -
> www.google.com).
7.7.4. IPX name resolution (network layer)

ipxnet name resolution (ipxnets file): XXX - add ipxnets name resolution explanation.
109
Advanced Topics
7.7.5. TCP/UDP port name resolution (transport layer)

Try to resolve a TCP/UDP port (e.g. 80) to something more "human readable".
TCP/UDP port conversion (system service): Wireshark will ask the operating system to convert a TCP
or UDP port to its well known name (e.g. 80 -> http).
XXX - mention the role of the /etc/services file (but don't forget the files and folders section)!
7.8. Checksums
Several network protocols use checksums to ensure data integrity.
Tip!
Applying checksums as described here is also known as redundancy checking.
What are checksums for?
Checksums are used to ensure the integrity of data portions for data transmission or storage. A
checksum is basically a calculated summary of such a data portion.
Network data transmissions often produce errors, such as toggled, missing or duplicated bits. As a
result, the data received might not be identical to the data transmitted, which is obviously a bad thing.
Because of these transmission errors, network protocols very often use checksums to detect such
errors. The transmitter will calculate a checksum of the data and transmits the data together with the
checksum. The receiver will calculate the checksum of the received data with the same algorithm
as the transmitter. If the received and calculated checksums don't match a transmission error has
occurred.
Some checksum algorithms are able to recover (simple) errors by calculating where the expected
error must be and repairing it.
If there are errors that cannot be recovered, the receiving side throws away the packet. Depending
on the network protocol, this data loss is simply ignored or the sending side needs to detect this loss
somehow and retransmits the required packet(s).
Using a checksum drastically reduces the number of undetected transmission errors. However, the
usual checksum algorithms cannot guarantee an error detection of 100%, so a very small number
of transmission errors may remain undetected.
There are several different kinds of checksum algorithms; an example of an often used checksum
algorithm is CRC32. The checksum algorithm actually chosen for a specific network protocol will
depend on the expected error rate of the network medium, the importance of error detection, the
processor load to perform the calculation, the performance needed and many other things.
Further information about checksums can be found at: http://en.wikipedia.org/wiki/Checksum.
7.8.1. Wireshark checksum validation

Wireshark will validate the checksums of several protocols, e.g.: IP, TCP, UDP, ...
110
Advanced Topics
It will do the same calculation as a "normal receiver" would do, and shows the checksum fields in the
packet details with a comment, e.g.: [correct], [invalid, must be 0x12345678] or alike.
Checksum validation can be switched off for various protocols in the Wireshark protocol preferences, e.g.
to (very slightly) increase performance.
If the checksum validation is enabled and it detected an invalid checksum, features like packet
reassembling won't be processed. This is avoided as incorrect connection data could "confuse" the internal
database.
7.8.2. Checksum offloading

The checksum calculation might be done by the network driver, protocol driver or even in hardware.
For example: The Ethernet transmitting hardware calculates the Ethernet CRC32 checksum and the
receiving hardware validates this checksum. If the received checksum is wrong Wireshark won't even see
the packet, as the Ethernet hardware internally throws away the packet.
Higher level checksums are "traditionally" calculated by the protocol implementation and the completed
packet is then handed over to the hardware.
Recent network hardware can perform advanced features such as IP checksum calculation, also known as
checksum offloading. The network driver won't calculate the checksum itself but will simply hand over
an empty (zero or garbage filled) checksum field to the hardware.
Note!
Checksum offloading often causes confusion as the network packets to be transmitted are
handed over to Wireshark before the checksums are actually calculated. Wireshark gets these
"empty" checksums and displays them as invalid, even though the packets will contain valid
checksums when they leave the network hardware later.
Checksum offloading can be confusing and having a lot of [invalid] messages on the screen can be
quite annoying. As mentioned above, invalid checksums may lead to unreassembled packets, making the
analysis of the packet data much harder.
You can do two things to avoid this checksum offloading problem:
• Turn off the checksum offloading in the network driver, if this option is available.
• Turn off checksum validation of the specific protocol in the Wireshark preferences.
111
Chapter 8. Statistics
8.1. Introduction
Wireshark provides a wide range of network statistics which can be accessed via the Statistics menu.
These statistics range from general information about the loaded capture file (like the number of captured
packets), to statistics about specific protocols (e.g. statistics about the number of HTTP requests and
responses captured).
• General statistics:
• Summary about the capture file.
• Protocol Hierarchy of the captured packets.
• Conversations e.g. traffic between specific IP addresses.
• Endpoints e.g. traffic to and from an IP addresses.
• IO Graphs visualizing the number of packets (or similar) in time.
• Protocol specific statistics:
• Service Response Time between request and response of some protocols.
• Various other protocol specific statistics.
Note!
The protocol specific statistics requires detailed knowledge about the specific protocol.
Unless you are familiar with that protocol, statistics about it will be pretty hard to understand.
8.2. The "Summary" window

General statistics about the current capture file.
112
Statistics
Figure 8.1. The "Summary" window
• File: general information about the capture file.
• Time: the timestamps when the first and the last packet were captured (and the time between them).
• Capture: information from the time when the capture was done (only available if the packet data was
captured from the network and not loaded from a file).
• Display: some display related information.
• Traffic: some statistics of the network traffic seen. If a display filter is set, you will see values in the
Captured column, and if any packages are marked, you will see values in the Marked column. The
values in the Captured column will remain the same as before, while the values in the Displayed
column will reflect the values corresponding to the packets shown in the display. The values in the
Marked column will reflect the values corresponding to the marked packages.
8.3. The "Protocol Hierarchy" window

The protocol hierarchy of the captured packets.
113
Statistics
Figure 8.2. The "Protocol Hierarchy" window
This is a tree of all the protocols in the capture. You can collapse or expand subtrees, by clicking on the
plus / minus icons. By default, all trees are expanded.
Each row contains the statistical values of one protocol. The Display filter will show the current display
filter.
The following columns containing the statistical values are available:
• Protocol: this protocol's name
• % Packets: the percentage of protocol packets, relative to all packets in the capture
• Packets: the absolute number of packets of this protocol
• Bytes: the absolute number of bytes of this protocol
• MBit/s: the bandwidth of this protocol, relative to the capture time
• End Packets: the absolute number of packets of this protocol (where this protocol was the highest
protocol to decode)
• End Bytes: the absolute number of bytes of this protocol (where this protocol was the highest protocol
to decode)
• End MBit/s: the bandwidth of this protocol, relative to the capture time (where this protocol was the
highest protocol to decode)
Note!
Packets will usually contain multiple protocols, so more than one protocol will be counted for
each packet. Example: In the screenshot IP has 99,17% and TCP 85,83% (which is together
much more than 100%).
114
Statistics
Note!
Protocol layers can consist of packets that won't contain any higher layer protocol, so the
sum of all higher layer packets may not sum up to the protocols packet count. Example: In
the screenshot TCP has 85,83% but the sum of the subprotocols (HTTP, ...) is much less.
This may be caused by TCP protocol overhead, e.g. TCP ACK packets won't be counted as
packets of the higher layer).
Note!
A single packet can contain the same protocol more than once. In this case, the protocol
is counted more than once. For example: in some tunneling configurations the IP layer can
appear twice.
8.4. Conversations
Statistics of the captured conversations.
8.4.1. What is a Conversation?

A network conversation is the traffic between two specific endpoints. For example, an IP conversation
is all the traffic between two IP addresses. The description of the known endpoint types can be found in
Section 8.5.1, “What is an Endpoint?”.
8.4.2. The "Conversations" window

The conversations window is similar to the endpoint Window; see Section 8.5.2, “The "Endpoints"
window” for a description of their common features. Along with addresses, packet counters, and byte
counters the conversation window adds four columns: the time in seconds between the start of the capture
and the start of the conversation ("Rel Start"), the duration of the conversation in seconds, and the average
bits (not bytes) per second in each direction.
Figure 8.3. The "Conversations" window
115
Statistics
Each row in the list shows the statistical values for exactly one conversation.
Name resolution will be done if selected in the window and if it is active for the specific protocol layer
(MAC layer for the selected Ethernet endpoints page).
Limit to display filter will only show conversations matching the current display filter.
The copy button will copy the list values to the clipboard in CSV (Comma Separated Values) format.
Tip!
This window will be updated frequently, so it will be useful, even if you open it before (or
while) you are doing a live capture.
8.4.3. The protocol specific "Conversation List" windows

Before the combined window described above was available, each of its pages was shown as a separate
window. Even though the combined window is much more convenient to use, these separate windows are
still available. The main reason is that they might process faster for very large capture files. However, as
the functionality is exactly the same as in the combined window, they won't be discussed in detail here.
8.5. Endpoints
Statistics of the endpoints captured.
Tip!
If you are looking for a feature other network tools call a hostlist, here is the right place to
look. The list of Ethernet or IP endpoints is usually what you're looking for.
8.5.1. What is an Endpoint?

A network endpoint is the logical endpoint of separate protocol traffic of a specific protocol layer. The
endpoint statistics of Wireshark will take the following endpoints into account:
• Ethernet: an Ethernet endpoint is identical to the Ethernet's MAC address.
• Fibre Channel: XXX - insert info here.
• FDDI: a FDDI endpoint is identical to the FDDI MAC address.
• IPv4: an IP endpoint is identical to its IP address.
• IPX: an IPX endpoint is concatenation of a 32 bit network number and 48 bit node address, be default
the Ethernets' MAC address.
• JXTA: a JXTA endpoint is a 160 bit SHA-1 URN.
• NCP: XXX - insert info here.
• RSVP: XXX - insert info here.
• SCTP: a SCTP endpoint is a combination of the host IP addresses (plural) and the SCTP port used. So
different SCTP ports on the same IP address are different SCTP endpoints, but the same SCTP port on
different IP addresses of the same host are still the same endpoint.
116
Statistics
• TCP: a TCP endpoint is a combination of the IP address and the TCP port used, so different TCP ports
on the same IP address are different TCP endpoints.
• Token Ring: a Token Ring endpoint is identical to the Token Ring MAC address.
• UDP: a UDP endpoint is a combination of the IP address and the UDP port used, so different UDP
ports on the same IP address are different UDP endpoints.
• USB: XXX - insert info here.
• WLAN: XXX - insert info here.
Broadcast / multicast endpoints

Broadcast / multicast traffic will be shown separately as additional endpoints. Of course, as
these endpoints are virtual endpoints, the real traffic will be received by all (multicast: some)
of the listed unicast endpoints.
8.5.2. The "Endpoints" window

This window shows statistics about the endpoints captured.
Figure 8.4. The "Endpoints" window
For each supported protocol, a tab is shown in this window. Each tab label shows the number of endpoints
captured (e.g. the tab label "Ethernet: 5" tells you that five ethernet endpoints have been captured). If no
endpoints of a specific protocol were captured, the tab label will be greyed out (although the related page
can still be selected).
Each row in the list shows the statistical values for exactly one endpoint.
Name resolution will be done if selected in the window and if it is active for the specific protocol layer
(MAC layer for the selected Ethernet endpoints page). As you might have noticed, the first row has a name
resolution of the first three bytes "Netgear", the second row's address was resolved to an IP address (using
117
Statistics
ARP) and the third was resolved to a broadcast (unresolved this would still be: ff:ff:ff:ff:ff:ff); the last two
Ethernet addresses remain unresolved.
Limit to display filter will only show conversations matching the current display filter.
Tip!
8.5.3. The protocol specific "Endpoint List" windows

Before the combined window described above was available, each of its pages was shown as a separate
window. Even though the combined window is much more convenient to use, these separate windows are
still available. The main reason is that they might process faster for very large capture files. However, as
the functionality is exactly the same as in the combined window, they won't be discussed in detail here.
8.6. The "IO Graphs" window

User configurable graph of the captured network packets.
You can define up to five differently colored graphs.
Figure 8.5. The "IO Graphs" window
The user can configure the following things:
• Graphs
• Graph 1-5: enable the specific graph 1-5 (only graph 1 is enabled by default)
• Color: the color of the graph (cannot be changed)
118
Statistics
• Filter: a display filter for this graph (only the packets that pass this filter will be taken into account
for this graph)
• Style: the style of the graph (Line/Impulse/FBar/Dot)
• X Axis
• Tick interval: an interval in x direction lasts (10/1 minutes or 10/1/0.1/0.01/0.001 seconds)
• Pixels per tick: use 10/5/2/1 pixels per tick interval
• View as time of day: option to view x direction labels as time of day instead of seconds or minutes
since beginning of capture
• Y Axis
• Unit: the unit for the y direction (Packets/Tick, Bytes/Tick, Bits/Tick, Advanced...) [XXX -
describe the Advanced feature.]
• Scale: the scale for the y unit (Logarithmic,Auto,10,20,50,100,200,500,...)
The save button will save the currently displayed portion of the graph as one of various file formats. The
save feature is only available when using GTK version 2.6 or higher (the latest Windows versions comply
with this requirement) and Wireshark version 0.99.7 or higher.
The copy button will copy values from selected graphs to the clipboard in CSV (Comma Separated Values)
format. The copy feature is only available in Wireshark version 0.99.8 or higher.
Tip!
Click in the graph to select the first package in the selected interval.
8.7. Service Response Time

The service response time is the time between a request and the corresponding response. This information
is available for many protocols.
Service response time statistics are currently available for the following protocols:
• DCE-RPC
• Fibre Channel
• H.225 RAS
• LDAP
• LTE MAC
• MGCP
• ONC-RPC
• SMB
119
Statistics
As an example, the DCE-RPC service response time is described in more detail.
Note!
The other Service Response Time windows will work the same way (or only slightly
different) compared to the following description.
8.7.1. The "Service Response Time DCE-RPC" window

The service response time of DCE-RPC is the time between the request and the corresponding response.
First of all, you have to select the DCE-RPC interface:
Figure 8.6. The "Compute DCE-RPC statistics" window
You can optionally set a display filter, to reduce the amount of packets.
Figure 8.7. The "DCE-RPC Statistic for ..." window
Each row corresponds to a method of the interface selected (so the EPM interface in version 3 has 7
methods). For each method the number of calls, and the statistics of the SRT time is calculated.
8.8. WLAN Traffic Statistics

Statistics of the captured WLAN traffic. This window will summarize the wireless network traffic found
in the capture. Probe requests will be merged into an existing network if the SSID matches.
120
Statistics
Figure 8.8. The "WLAN Traffic Statistics" window
Each row in the list shows the statistical values for exactly one wireless network.
Name resolution will be done if selected in the window and if it is active for the MAC layer.
Only show existing networks will exclude probe requests with a SSID not matching any network from
the list.
Tip!
8.9. The protocol specific statistics windows

The protocol specific statistics windows display detailed information of specific protocols and might be
described in a later version of this document.
Some of these statistics are described at the http://wiki.wireshark.org/Statistics pages.
121
Chapter 9. Telephony
9.1. Introduction
Wireshark provides a wide range of telephony related network statistics which can be accessed via the
Telephony menu.
These statistics range from specific signaling protocols, to analysis of signaling and media flows. If
encoded in a compatible encoding the media flow can even be played.
9.2. RTP Analysis

The RTP analysis function takes the selected RTP stream (and the reverse stream, if possible) and generates
a list of statistics on it.
Figure 9.1. The "RTP Stream Analysis" window
Starting with basic data as packet number and sequence number, further statistics are created based on
arrival time, delay, jitter, packet size, etc.
Besides the per packet statistics, the lower pane shows the overall statistics, with minimums and maximums
for delta, jitter and clock skew. Also an indication of lost packets is included.
The RTP Stream Analysis window further provides the option to save the RTP payload (as raw data or, if in
a PCM encoding, in an Audio file). Other options a to export and plot various statistics on the RTP streams.
9.3. VoIP Calls

The VoIP Calls window shows a list of all detected VoIP calls in the captured traffic. It finds calls by
their signaling.
122
Telephony
More details are described at the http://wiki.wireshark.org/VoIP_calls page.
9.4. LTE MAC Traffic Statistics

Statistics of the captured LTE MAC traffic. This window will summarize the LTE MAC traffic found in
the capture.
Figure 9.2. The "LTE MAC Traffic Statistics" window
The top pane shows statistics for common channels. Each row in the middle pane shows statistical
highlights for exactly one UE/C-RNTI. In the lower pane, you can see the for the currently selected UE/
C-RNTI the traffic broken down by individual channel.
9.5. LTE RLC Traffic Statistics

Statistics of the captured LTE RLC traffic. This window will summarize the LTE RLC traffic found in
the capture.
123
Telephony
Figure 9.3. The "LTE RLC Traffic Statistics" window
At the top, the check-box allows this window to include RLC PDUs found withing MAC PDUs or not.
This will affect both the PDUs counted as well as the display filters generated (see below).
The upper list shows summaries of each active UE. Each row in the lower list shows statistical highlights
for individual channels within the selected UE.
The lower part of the windows allows display filters to be generated and set for the selected channel. Note
that in the case of Acknowledged Mode channels, if a single direction is chosen, the generated filter will
show data in that direction and control PDUs in the opposite direction.
9.6. The protocol specific statistics windows

The protocol specific statistics windows display detailed information of specific protocols and might be
described in a later version of this document.
Some of these statistics are described at the http://wiki.wireshark.org/Statistics pages.
124
Chapter 10. Customizing Wireshark
10.1. Introduction
Wireshark's default behaviour will usually suit your needs pretty well. However, as you become more
familiar with Wireshark, it can be customized in various ways to suit your needs even better. In this chapter
we explore:
• How to start Wireshark with command line parameters
• How to colorize the packet list
• How to control protocol dissection
• How to use the various preference settings
10.2. Start Wireshark from the command line

You can start Wireshark from the command line, but it can also be started from most Window managers
as well. In this section we will look at starting it from the command line.
Wireshark supports a large number of command line parameters. To see what they are, simply enter the
command wireshark -h and the help information shown in Example 10.1, “Help information available
from Wireshark” (or something similar) should be printed.
125
Customizing Wireshark
Example 10.1. Help information available from Wireshark
Wireshark 1.3.2
Interactively dump and analyze network traffic.
See http://www.wireshark.org for more information.
Copyright 1998-2009 Gerald Combs <gerald@wireshark.org> and contributors.

This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
Usage: wireshark [options] ... [ <infile> ]
Capture interface:
-i <interface> name or idx of interface (def: first non-loopback)
-f <capture filter> packet filter in libpcap filter syntax
-s <snaplen> packet snapshot length (def: 65535)
-p don't capture in promiscuous mode
-k start capturing immediately (def: do nothing)
-Q quit Wireshark after capturing
-S update packet display when new packets are captured
-l turn on automatic scrolling while -S is in use
-B <buffer size> size of kernel buffer (def: 1MB)
-y <link type> link layer type (def: first appropriate)
-D print list of interfaces and exit
-L print list of link-layer types of iface and exit
Capture stop conditions:

-c <packet count> stop after n packets (def: infinite)
-a <autostop cond.> ... duration:NUM - stop after NUM seconds
filesize:NUM - stop this file after NUM KB
files:NUM - stop after NUM files
Capture output:
-b <ringbuffer opt.> ... duration:NUM - switch to next file after NUM secs
filesize:NUM - switch to next file after NUM KB
files:NUM - ringbuffer: replace after NUM files
Input file:
-r <infile> set the filename to read from (no pipes or stdin!)
Processing:
-R <read filter> packet filter in Wireshark display filter syntax
-n disable all name resolutions (def: all enabled)
-N <name resolve flags> enable specific name resolution(s): "mntC"
User interface:
-C <config profile> start with specified configuration profile
-g <packet number> go to specified packet number after "-r"
-J <jump filter> jump to the first packet matching the (display) filter
-j search backwards for a matching packet after "-J"
-m <font> set the font name used for most text
-t ad|a|r|d|dd|e output format of time stamps (def: r: rel. to first)
-X <key>:<value> eXtension options, see man page for details
-z <statistics> show various statistics, see man page for details
Output:
-w <outfile|-> set the output filename (or '-' for stdout)
Miscellaneous:
-h display this help and exit
-v display version info and exit
-P <key>:<path> persconf:path - personal configuration files
persdata:path - personal data files
-o <name>:<value> ... override preference or recent setting
-K <keytab> keytab file to use for kerberos decryption
We will examine each of the command line options in turn.
126
The first thing to notice is that issuing the command wireshark by itself will bring up Wireshark. However,
you can include as many of the command line parameters as you like. Their meanings are as follows ( in
alphabetical order ): XXX - is the alphabetical order a good choice? Maybe better task based?
-a <capture autostop condition> Specify a criterion that specifies when Wireshark is to stop writing
to a capture file. The criterion is of the form test:value, where test
is one of:
duration:value Stop writing to a capture file after value of

seconds have elapsed.
filesize:value Stop writing to a capture file after it reaches

a size of value kilobytes (where a kilobyte is
1000 bytes, not 1024 bytes). If this option is
used together with the -b option, Wireshark
will stop writing to the current capture file
and switch to the next one if filesize is
reached.
files:value Stop writing to capture files after value

number of files were written.
-b <capture ring buffer option> If a maximum capture file size was specified, this option causes
Wireshark to run in "ring buffer" mode, with the specified number
of files. In "ring buffer" mode, Wireshark will write to several
capture files. Their name is based on the number of the file and on
the creation date and time.
When the first capture file fills up, Wireshark will switch to writing
to the next file, until it fills up the last file, at which point it'll discard
the data in the first file (unless 0 is specified, in which case, the
number of files is unlimited) and start writing to that file and so on.
If the optional duration is specified, Wireshark will also switch to

the next file when the specified number of seconds has elapsed even
if the current file is not completely fills up.
duration:value Switch to the next file after value seconds

have elapsed, even if the current file is not
completely filled up.
filesize:value Switch to the next file after it reaches a size

of value kilobytes (where a kilobyte is 1000
bytes, not 1024 bytes).
files:value Begin again with the first file after value

number of files were written (form a ring
buffer).
-B <capture buffer size (Win32 Win32 only: set capture buffer size (in MB, default is 1MB). This
only)> is used by the the capture driver to buffer packet data until that
data can be written to disk. If you encounter packet drops while
capturing, try to increase this size.
127
-c <capture packet count> This option specifies the maximum number of packets to capture
when capturing live data. It would be used in conjunction with the
-k option.
-D Print a list of the interfaces on which Wireshark can capture, and

exit. For each network interface, a number and an interface name,
possibly followed by a text description of the interface, is printed.
The interface name or the number can be supplied to the -i flag to
specify an interface on which to capture.
This can be useful on systems that don't have a command to list

them (e.g., Windows systems, or UNIX systems lacking ifconfig -
a); the number can be useful on Windows 2000 and later systems,
where the interface name is a somewhat complex string.
Note that "can capture" means that Wireshark was able to open
that device to do a live capture; if, on your system, a program
doing a network capture must be run from an account with special
privileges (for example, as root), then, if Wireshark is run with the
-D flag and is not run from such an account, it will not list any
interfaces.
-f <capture filter> This option sets the initial capture filter expression to be used when
capturing packets.
-g <packet number> After reading in a capture file using the -r flag, go to the given
packet number.
-h The -h option requests Wireshark to print its version and usage

instructions (as shown above) and exit.
-i <capture interface> Set the name of the network interface or pipe to use for live packet
capture.
Network interface names should match one of the names listed

in wireshark -D (described above); a number, as reported by
wireshark -D, can also be used. If you're using UNIX, netstat -i or
ifconfig -a might also work to list interface names, although not all
versions of UNIX support the -a flag to ifconfig.
If no interface is specified, Wireshark searches the list of interfaces,

choosing the first non-loopback interface if there are any non-
loopback interfaces, and choosing the first loopback interface if
there are no non-loopback interfaces; if there are no interfaces,
Wireshark reports an error and doesn't start the capture.
Pipe names should be either the name of a FIFO (named pipe) or

``-'' to read data from the standard input. Data read from pipes must
be in standard libpcap format.
-J <jump filter> After reading in a capture file using the -r flag, jump to the first
packet which matches the filter expression. The filter expression is
in display filter format. If an exact match cannot be found the first
packet afterwards is selected.
-j Use this option after the -J option to search backwards for a first
packet to go to.
128
-k The -k option specifies that Wireshark should start capturing

packets immediately. This option requires the use of the -i
parameter to specify the interface that packet capture will occur
from.
-l This option turns on automatic scrolling if the packet list pane is

being updated automatically as packets arrive during a capture ( as
specified by the -S flag).
-L List the data link types supported by the interface and exit.
-m <font> This option sets the name of the font used for most text displayed
by Wireshark. XXX - add an example!
-n Disable network object name resolution (such as hostname, TCP

and UDP port names).
-N <name resolving flags> Turns on name resolving for particular types of addresses and port
numbers; the argument is a string that may contain the letters m
to enable MAC address resolution, n to enable network address
resolution, and t to enable transport-layer port number resolution.
This overrides -n if both -N and -n are present. The letter C enables
concurrent (asynchronous) DNS lookups.
-o <preference/recent settings> Sets a preference or recent value, overriding the default value and
any value read from a preference/recent file. The argument to the
flag is a string of the form prefname:value, where prefname is the
name of the preference (which is the same name that would appear
in the preference/recent file), and value is the value to which it
should be set. Multiple instances of -o <preference settings> can
be given on a single command line.
An example of setting a single preference would be:
wireshark -o mgcp.display_dissect_tree:TRUE
An example of setting multiple preferences would be:
wireshark -o mgcp.display_dissect_tree:TRUE -o
mgcp.udp.callagent_port:2627
Tip!
You can get a list of all available preference strings
from the preferences file, see Appendix A, Files and
Folders.
User access tables can be overridden using "uat," followed by the

UAT file name and a valid record for the file:
wireshark -o "uat:user_dlts:\"User 0 (DLT=147)\",\"http\",

\"0\",\"\",\"0\",\"\""
The example above would dissect packets with a libpcap data

link type 147 as HTTP, just as if you had configured it in the
DLT_USER protocol preferences.
129
-p Don't put the interface into promiscuous mode. Note that the
interface might be in promiscuous mode for some other reason;
hence, -p cannot be used to ensure that the only traffic that is
captured is traffic sent to or from the machine on which Wireshark
is running, broadcast traffic, and multicast traffic to addresses
received by that machine.
-P <path setting> Special path settings usually detected automatically. This is used
for special cases, e.g. starting Wireshark from a known location on
an USB stick.
The criterion is of the form key:path, where key is one of:
persconf:path path of personal configuration files, like the

preferences files.
persdata:path path of personal data files, it's the folder

initially opened. After the initialization, the
recent file will keep the folder last used.
-Q This option forces Wireshark to exit when capturing is complete. It

can be used with the -c option. It must be used in conjunction with
the -i and -w options.
-r <infile> This option provides the name of a capture file for Wireshark to read
and display. This capture file can be in one of the formats Wireshark
understands.
-R <read (display) filter> This option specifies a display filter to be applied when reading
packets from a capture file. The syntax of this filter is that of the
display filters discussed in Section 6.3, “Filtering packets while
viewing”. Packets not matching the filter are discarded.
-s <capture snaplen> This option specifies the snapshot length to use when capturing
packets. Wireshark will only capture <snaplen> bytes of data for
each packet.
-S This option specifies that Wireshark will display packets as it

captures them. This is done by capturing in one process and
displaying them in a separate process. This is the same as "Update
list of packets in real time" in the Capture Options dialog box.
-t <time stamp format> This option sets the format of packet timestamps that are displayed
in the packet list window. The format can be one of:
• r relative, which specifies timestamps are displayed relative to

the first packet captured.
• a absolute, which specifies that actual times be displayed for

all packets.
• ad absolute with date, which specifies that actual dates and

times be displayed for all packets.
• d delta, which specifies that timestamps are relative to the

previous packet.
130
• e epoch, which specifies that timestamps are seconds since

epoch (Jan 1, 1970 00:00:00)
-v The -v option requests Wireshark to print out its version

information and exit.
-w <savefile> This option sets the name of the savefile to be used when saving
a capture file.
-y <capture link type> If a capture is started from the command line with -k, set the data
link type to use while capturing packets. The values reported by -
L are the values that can be used.
-X <eXtension option> Specify an option to be passed to a TShark module. The eXtension

option is in the form extension_key:value, where extension_key can
be:
lua_script:lua_script_filename; Tells Wireshark to load the given

script in addition to the default Lua scripts.
-z <statistics-string> Get Wireshark to collect various types of statistics and display the
result in a window that updates in semi-real time. XXX - add more
details here!
10.3. Packet colorization

A very useful mechanism available in Wireshark is packet colorization. You can set-up Wireshark so that
it will colorize packets according to a filter. This allows you to emphasize the packets you are (usually)
interested in.
Tip!
You will find a lot of Coloring Rule examples at the Wireshark Wiki Coloring Rules page
at http://wiki.wireshark.org/ColoringRules.
There are two types of coloring rules in Wireshark. Temporary ones that are only used until you quit the
program. And permanent ones that will be saved to a preference file so that they are available on a next
session.
Temporary coloring rules can be added by selecting a packet and pressing the <ctrl> key together with one
of the number keys. This will create a coloring rule based on the currently selected conversation. It will
try to create a conversation filter based on TCP first, then UDP, then IP and at last Ethernet. Temporary
filters can also be created by selecting the "Colorize with Filter > Color X" menu items when rightclicking
in the packet-detail pane.
To permanently colorize packets, select the Coloring Rules... menu item from the View menu; Wireshark
will pop up the "Coloring Rules" dialog box as shown in Figure 10.1, “The "Coloring Rules" dialog box”.
131
Figure 10.1. The "Coloring Rules" dialog box
Once the Coloring Rules dialog box is up, there are a number of buttons you can use, depending on whether
or not you have any color filters installed already.
Note!
You will need to carefully select the order the coloring rules are listed as they are applied
in order from top to bottom. So, more specific rules need to be listed before more general
rules. For example, if you have a color rule for UDP before the one for DNS, the color rule
for DNS will never be applied (as DNS uses UDP, so the UDP rule will match first).
If this is the first time you have used Coloring Rules, click on the New button which will bring up the Edit
color filter dialog box as shown in Figure 10.2, “The "Edit Color Filter" dialog box”.
Figure 10.2. The "Edit Color Filter" dialog box
In the Edit Color dialog box, simply enter a name for the color filter, and enter a filter string in the Filter
text field. Figure 10.2, “The "Edit Color Filter" dialog box” shows the values arp and arp which means
that the name of the color filter is arp and the filter will select protocols of type arp. Once you have
entered these values, you can choose a foreground and background color for packets that match the filter
expression. Click on Foreground color... or Background color... to achieve this and Wireshark will
pop up the Choose foreground/background color for protocol dialog box as shown in Figure 10.3, “The
"Choose color" dialog box”.
132
Figure 10.3. The "Choose color" dialog box
Select the color you desire for the selected packets and click on OK.
Note!
You must select a color in the colorbar next to the colorwheel to load values into the RGB
values. Alternatively, you can set the values to select the color you want.
Figure 10.4, “Using color filters with Wireshark” shows an example of several color filters being used in
Wireshark. You may not like the color choices, however, feel free to choose your own.
If you are uncertain which coloring rule actually took place for a specific packet, have a look at the
[Coloring Rule Name: ...] and [Coloring Rule String: ...] fields.
Figure 10.4. Using color filters with Wireshark
133
10.4. Control Protocol dissection

The user can control how protocols are dissected.
Each protocol has its own dissector, so dissecting a complete packet will typically involve several
dissectors. As Wireshark tries to find the right dissector for each packet (using static "routes" and heuristics
"guessing"), it might choose the wrong dissector in your specific case. For example, Wireshark won't know
if you use a common protocol on an uncommon TCP port, e.g. using HTTP on TCP port 800 instead of
the standard port 80.
There are two ways to control the relations between protocol dissectors: disable a protocol dissector
completely or temporarily divert the way Wireshark calls the dissectors.
10.4.1. The "Enabled Protocols" dialog box

The Enabled Protocols dialog box lets you enable or disable specific protocols; all protocols are enabled
by default. When a protocol is disabled, Wireshark stops processing a packet whenever that protocol is
encountered.
Note!
Disabling a protocol will prevent information about higher-layer protocols from being
displayed. For example, suppose you disabled the IP protocol and selected a packet
containing Ethernet, IP, TCP, and HTTP information. The Ethernet information would be
displayed, but the IP, TCP and HTTP information would not - disabling IP would prevent it
and the other protocols from being displayed.
To enable/disable protocols select the Enabled Protocols... item from the Analyze menu; Wireshark will
pop up the "Enabled Protocols" dialog box as shown in Figure 10.5, “The "Enabled Protocols" dialog box”.
134
Figure 10.5. The "Enabled Protocols" dialog box
To disable or enable a protocol, simply click on it using the mouse or press the space bar when the protocol
is highlighted. Note that typing the first few letters of the protocol name when the Enabled Protocols dialog
box is active will temporarily open a search text box and automatically select the first matching protocol
name (if it exists).
Warning!
You have to use the Save button to save your settings. The OK or Apply buttons will not
save your changes permanently, so they will be lost when Wireshark is closed.
You can choose from the following actions:
1. Enable All: Enable all protocols in the list.
2. Disable All: Disable all protocols in the list.
3. Invert: Toggle the state of all protocols in the list.
4. OK: Apply the changes and close the dialog box.
5. Apply: Apply the changes and keep the dialog box open.
6. Save: Save the settings to the disabled_protos, see Appendix A, Files and Folders for details.
7. Cancel: Cancel the changes and close the dialog box.
10.4.2. User Specified Decodes

The "Decode As" functionality let you temporarily divert specific protocol dissections. This might be
useful for example, if you do some uncommon experiments on your network.
135
Decode As is accessed by selecting the Decode As... item from the Analyze menu; Wireshark will pop up
the "Decode As" dialog box as shown in Figure 10.6, “The "Decode As" dialog box”.
Figure 10.6. The "Decode As" dialog box
The content of this dialog box depends on the selected packet when it was opened.
Warning!
The user specified decodes can not be saved. If you quit Wireshark, these settings will be lost.
1. Decode: Decode packets the selected way.
2. Do not decode: Do not decode packets the selected way.
3. Link/Network/Transport: Specify the network layer at which "Decode As" should take place.
Which of these pages are available depends on the content of the selected packet when this dialog
box is opened.
4. Show Current: Open a dialog box showing the current list of user specified decodes.
5. OK: Apply the currently selected decode and close the dialog box.
6. Apply: Apply the currently selected decode and keep the dialog box open.
7. Cancel: Cancel the changes and close the dialog box.
10.4.3. Show User Specified Decodes

This dialog box shows the currently active user specified decodes.
136
Figure 10.7. The "Decode As: Show" dialog box
1. OK: Close this dialog box.
2. Clear: Removes all user specified decodes.
10.5. Preferences
There are a number of preferences you can set. Simply select the Preferences... menu item from the Edit
menu; and Wireshark will pop up the Preferences dialog box as shown in Figure 10.8, “The preferences
dialog box”, with the "User Interface" page as default. On the left side is a tree where you can select the
page to be shown.
Note!
Preference settings are added frequently. For a recent explanation of the preference
pages and their settings have a look at the Wireshark Wiki Preferences page at http://
wiki.wireshark.org/Preferences.
Warning!
The OK or Apply button will not save the preference settings, you'll have to save the settings
by clicking the Save button.
• The OK button will apply the preferences settings and close the dialog.
• The Apply button will apply the preferences settings and keep the dialog open.
• The Save button will apply the preferences settings, save the settings on the hard disk and keep the
dialog open.
• The Cancel button will restore all preferences settings to the last saved state.
137
Figure 10.8. The preferences dialog box
10.5.1. Interface Options

In the Capture preferences it is possible to configure several options for the interfaces available on your
computer. Select the Capture pane and press the Interfaces: Edit button. In this window it is possible to
change the default link-layer header type for the interface, add a comment or choose to hide a interface
from other parts of the program.
Figure 10.9. The interface options dialog box
Each row contains options for each interface available on your computer.
• Device: the device name provided by the operating system.
• Description: provided by the operating system.
138
• Default link-layer: each interface may provide several link-layer header types. The default link-layer
chosen here is the one used when you first start Wireshark. It is also possible to change this value in
Section 4.5, “The "Capture Options" dialog box” when you start a capture. For a detailed description,
see Section 4.9, “Link-layer header type”.
• Comment: a user provided description of the interface. This comment will be used as a description
instead of the operating system description.
• Hide?: enable this option to hide the interface from other parts of the program.
10.6. Configuration Profiles

Configuration Profiles can be used to configure and use more than one set of preferences and
configurations. Select the Configuration Profiles... menu item from the Edit menu, or simply press Shift-
Ctrl-A; and Wireshark will pop up the Configuration Profiles dialog box as shown in Figure 10.10, “The
configuration profiles dialog box”. It is also possible to click in the "Profile" part of the statusbar to popup
a menu with available Configuration Profiles (Figure 3.20, “The Statusbar with a configuration profile
menu”).
Configuration files stored in the Profiles:
• Preferences (preferences) (Section 10.5, “Preferences”)
• Capture Filters (cfilters) (Section 6.6, “Defining and saving filters”)
• Display Filters (dfilters) (Section 6.6, “Defining and saving filters”)
• Coloring Rules (colorfilters) (Section 10.3, “Packet colorization”)
• Disabled Protocols (disabled_protos) (Section 10.4.1, “The "Enabled Protocols" dialog box”)
• User Accessible Tables:
• Display Filter Macros (dfilter_macros) (Section 10.8, “Display Filter Macros”)
• GeoIP Database Paths (geoip_db_paths) (Section 10.9, “GeoIP Database Paths”)
• K12 Protocols (k12_protos) (Section 10.10, “Tektronix K12xx/15 RF5 protocols Table”)
• PRES Users Context List (pres_context_list) (Section 10.11, “PRES Users Context List”)
• SCCP Users Table (sccp_users) (Section 10.12, “SCCP users Table”)
• SMI Modules (smi_modules) (Section 10.13, “SMI (MIB and PIB) Modules”)
• SMI Paths (smi_paths) (Section 10.14, “SMI (MIB and PIB) Paths”)
• SNMP Enterprise Specific Trap Types (snmp_specific_traps) (Section 10.15, “SNMP Enterprise
Specific Trap Types”)
• SNMP Users (snmp_users) (Section 10.16, “SNMP users Table”)
• User DLTs Table (user_dlts) (Section 10.17, “User DLTs protocol table”)
• Some recent settings (recent), such as pane sizes in the Main window (Section 3.3, “The Main
window”), column widths in the packet list (Section 3.17, “The "Packet List" pane”), all selections
in the "View" menu (Section 3.7, “The "View" menu”) and the last directory navigated to in the File
Open dialog.
139
Other configurations
All other configurations are stored in the personal configuration folder, and are common to
all profiles.
Figure 10.10. The configuration profiles dialog box
New This button adds a new profile to the profiles list. The name of the
created profile is "New profile" and can be changed in the Properties
field.
Copy This button adds a new profile to the profiles list, copying all
configuration from the profile currently selected in the list. The name
of the created profile is the same as the copied profile, with the text
"(copy)" applied. The name can be changed in the Properties field.
Delete This button deletes the selected profile, including all configuration
files used in this profile. It is not possible to delete the "Default"
profile.
Configuration Profiles You can select a configuration profile from this list (which will fill in
the profile name in the fields down at the bottom of the dialog box).
Profile name: You can change the name of the currently selected profile here.
Used as a folder name

The profile name will be used as a folder name in the
configured "Personal configurations" folder. If adding
multiple profiles with the same name, only one profile
will be created.
Illegal characters
On Windows the profile name cannot start or end with
a period (.), and cannot contain any of the following
characters: \ / : * ? " < > |
140
On Unix the profile name cannot contain the '/' character.
OK This button saves all changes, applies the selected profile and closes
the dialog.
Apply This button saves all changes, applies the selected profile and keeps
the dialog open.
Cancel Close this dialog. This will discard unsaved settings, new profiles will
not be added and deleted profiles will not be deleted.
Help Show this help page.
10.7. User Table

The User Table editor is used for managing various tables in wireshark. Its main dialog works very
similarly to that of Section 10.3, “Packet colorization”.
10.8. Display Filter Macros

Display Filter Macros are a mechanism to create shortcuts for complex filters. For example defining a
display filter macro named tcp_conv whose text is ( (ip.src == $1 and ip.dst == $2 and tcp.srcport ==
$3 and tcp.dstport == $4) or (ip.src == $2 and ip.dst == $1 and tcp.srcport == $4 and tcp.dstport ==
$3) ) would allow to use a display filter like ${tcp_conv:10.1.1.2;10.1.1.3;1200;1400} instead of typing
the whole filter.
Display Filter Macros can be managed with a Section 10.7, “User Table” by selecting Analyze # Display
Filter Macros from the menu. The User Table has the following fields
Name The name of the macro.
Text The replacement text for the macro it uses $1, $2, $3, ... as the input arguments.
10.9. GeoIP Database Paths

If your copy of Wireshark supports MaxMind's GeoIP library, you can use their databases to match IP
addresses to countries, cites, autonomous system numbers, ISPs, and other bits of information. Some
databases are available at no cost, while others require a licensing fee. See the MaxMind web site for more
information.
This table is handled by an Section 10.7, “User Table” with the following fields.
Database pathname This specifies a directory containing GeoIP data files. Any files beginning
with Geo and ending with .dat will be automatically loaded. A total of 8
files can be loaded.
The locations for your data files are up to you, but /usr/share/GeoIP
(Linux), C:\GeoIP (Windows), C:\Program Files\Wireshark
\GeoIP (Windows) might be good choices.
141
10.10. Tektronix K12xx/15 RF5 protocols Table

The Tektronix K12xx/15 rf5 file format uses helper files (*.stk) to identify the various protocols that are
used by a certain interface. Wireshark doesn't read these stk files, it uses a table that helps it identify which
lowest layer protocol to use.
Stk file to protocol matching is handled by an Section 10.7, “User Table” with the following fields.
Match string A partial match for an stk filename, the first match wins, so if you have a specific case
and a general one the specific one must appear first in the list.
Protocol This is the name of the encapsulating protocol (the lowest layer in the packet data) it
can be either just the name of the protocol (e.g. mtp2, eth_witoutfcs, sscf-nni ) or the
name of the encapsulation protocol and the "application" protocol over it separated
by a colon (e.g sscop:sscf-nni, sscop:alcap, sscop:nbap, ...)
10.11. PRES Users Context List

Wireshark uses this table to map a presentation context identifier to a given object identifier when the
capture does not contain a PRES package with a presentation context definition list for the conversation.
Context Id An Integer representing the presentation context identifier for which this
association is valid.
Syntax Name OID The object identifier representing the abstract syntax name, which defines the
protocol that is carried over this association.
10.12. SCCP users Table

Wireshark uses this table to map specific protocols to a certain DPC/SSN combination for SCCP.
Network Indicator An Integer representing the network indicator for which this association is
valid.
Called DPCs An range of integers representing the dpcs for which this association is valid.
Called SSNs An range of integers representing the ssns for which this association is valid.
User protocol The protocol that is carried over this association
10.13. SMI (MIB and PIB) Modules

If your copy of Wireshark supports libSMI, you can specify a list of MIB and PIB modules here. The
COPS and SNMP dissectors can use them to resolve OIDs.
Module name The name of the module, e.g. IF-MIB.
10.14. SMI (MIB and PIB) Paths

If your copy of Wireshark supports libSMI, you can specify one or more paths to MIB and PIB modules
here.
142
Directory name A module directory, e.g. /usr/local/snmp/mibs. Wireshark automatically

uses the standard SMI path for your system, so you usually don't have to add
anything here.
10.15. SNMP Enterprise Specific Trap Types

Wireshark uses this table to map specific-trap values to user defined descriptions in a Trap PDU. The
description is shown in the packet details specific-trap element.
Enterprise OID The object identifier representing the object generating the trap.
Trap Id An Integer representing the specific-trap code.
Description The description to show in the packet details.
10.16. SNMP users Table

Wireshark uses this table to verify authentication and to decrypt encrypted SNMPv3 packets.
Engine ID If given this entry will be used only for packets whose engine id is this.
This field takes an hexadecimal string in the form 0102030405.
Username This is the userName. When a single user has more than one password
for different SNMP-engines the first entry to match both is taken, if you
need a catch all engine-id (empty) that entry should be the last one.
Authentication model Which auth model to use (either "MD5" or "SHA1").
Password The authentication password. Use '\xDD' for unprintable characters.

An hexadecimal password must be entered as a sequence of '\xDD'
characters. For example the hex password 010203040506 must be entered
as '\x01\x02\x03\x04\x05\x06'.
Privacy protocol Which encryption algorithm to use (either "DES" or "AES").
Privacy password The privacy password. Use '\xDD' for unprintable characters. An
hexadecimal password must be entered as a sequence of '\xDD' characters.
For example the hex password 010203040506 must be entered as
'\x01\x02\x03\x04\x05\x06'.
10.17. User DLTs protocol table

When a pcap file uses one of the user DLTs (147 to 162) wireshark uses this table to know which protocol(s)
to use for each user DLT.
DLT One of the user dlts.
Payload protocol This is the name of the payload protocol (the lowest layer in the packet data).
(e.g. "eth" for ethernet, "ip" for IPv4)
143
Header size If there is a header protocol (before the payload protocol) this tells which size
this header is. A value of 0 disables the header protocol.
Header protocol The name of the header protocol to be used (uses "data" as default).
Trailer size If there is a trailer protocol (after the payload protocol) this tells which size this
trailer is. A value of 0 disables the trailer protocol.
Trailer protocol The name of the trailer protocol to be used (uses "data" as default).
10.18. IKEv2 decryption table

Wireshark can decrypt Encrypted Payloads of IKEv2 (Internet Key Exchange version 2) packets if
necessary information is provided. Note that you can decrypt only IKEv2 packets with this feature. If
you want to decrypt IKEv1 packets or ESP packets, use Log Filename setting under ISAKMP protocol
preference or settings under ESP protocol preference respectively.
Initiator's SPI Initiator's SPI of the IKE_SA. This field takes hexadecimal string without
"0x" prefix and the length must be 16 hex chars (represents 8 octets).
Responder's SPI Responder's SPI of the IKE_SA. This field takes hexadecimal string
without "0x" prefix and the length must be 16 hex chars (represents 8
octets).
SK_ei Key used to encrypt/decrypt IKEv2 packets from initiator to responder.

This field takes hexadecimal string without "0x" prefix and its length must
meet the requirement of the encryption algorithm selected.
SK_er Key used to encrypt/decrypt IKEv2 packets from responder to initiator.

This field takes hexadecimal string without "0x" prefix and its length must
meet the requirement of the encryption algorithm selected.
Encryption Algorithm Encryption algorithm of the IKE_SA.
SK_ai Key used to calculate Integrity Checksum Data for IKEv2 packets from
responder to initiator. This field takes hexadecimal string without "0x"
prefix and its length must meet the requirement of the integrity algorithm
selected.
SK_ar Key used to calculate Integrity Checksum Data for IKEv2 packets from
initiator to responder. This field takes hexadecimal string without "0x"
prefix and its length must meet the requirement of the integrity algorithm
selected.
Integrity Algorithm Integrity algorithm of the IKE_SA.
144
Chapter 11. Lua Support in Wireshark
11.1. Introduction
Wireshark has an embedded Lua interpreter. Lua is a powerful light-weight programming language
designed for extending applications. Lua is designed and implemented by a team at PUC-Rio, the Pontifical
Catholic University of Rio de Janeiro in Brazil. Lua was born and raised at Tecgraf, the Computer Graphics
Technology Group of PUC-Rio, and is now housed at Lua.org. Both Tecgraf and Lua.org are laboratories
of the Department of Computer Science.
In Wireshark Lua can be used to write dissectors and taps.
Wireshark's Lua interpreter starts by loading init.lua that is located in the global configuration directory
of Wireshark. Lua is disabled by default by setting the variable disable_lua to true in init.lua. To enable
lua the line that sets that variable must be removed or commented out.
After loading init.lua from the data directory if lua is enabled Wireshark will try to load a file named
init.lua in the user's directory.
Wireshark will also load all files with .lua suffix from both the global and the personal plugins directory.
The command line option -X lua_script:<file.lua> can be used to load lua scripts as well.
The Lua code will be executed once after all the protocols have being initialized and before reading any file.
11.2. Example of Dissector written in Lua

do
local p_multi = Proto("multi","MultiProto");
local vs_protos = {
[2] = "mtp2",
[3] = "mtp3",
[4] = "alcap",
[5] = "h248",
[6] = "ranap",
[7] = "rnsap",
[8] = "nbap"
}
local f_proto = ProtoField.uint8("multi.protocol","Protocol",base.DEC,vs_protos)

local f_dir = ProtoField.uint8("multi.direction","Direction",base.DEC,{ [1] = "incoming", [0] =
local f_text = ProtoField.string("multi.text","Text")
p_multi.fields = { f_proto, f_dir, f_text }
local data_dis = Dissector.get("data")
local protos = {
[2] = Dissector.get("mtp2"),
[3] = Dissector.get("mtp3"),
[4] = Dissector.get("alcap"),
[5] = Dissector.get("h248"),
[6] = Dissector.get("ranap"),
[7] = Dissector.get("rnsap"),
[8] = Dissector.get("nbap"),
[9] = Dissector.get("rrc"),
145
Lua Support in Wireshark
[10] = DissectorTable.get("sctp.ppi"):get_dissector(3), -- m3ua

[11] = DissectorTable.get("ip.proto"):get_dissector(132), -- sctp
}
function p_multi.dissector(buf,pkt,root)
local t = root:add(p_multi,buf(0,2))
t:add(f_proto,buf(0,1))
t:add(f_dir,buf(1,1))
local proto_id = buf(0,1):uint()
local dissector = protos[proto_id]
if dissector ~= nil then

dissector:call(buf(2):tvb(),pkt,root)
elseif proto_id < 2 then
t:add(f_text,buf(2))
-- pkt.cols.info:set(buf(2,buf:len() - 3):string())
else
data_dis:call(buf(2):tvb(),pkt,root)
end
end
local wtap_encap_table = DissectorTable.get("wtap_encap")

local udp_encap_table = DissectorTable.get("udp.port")
wtap_encap_table:add(wtap.USER15,p_multi)
wtap_encap_table:add(wtap.USER12,p_multi)
udp_encap_table:add(7555,p_multi)
end
11.3. Example of Listener written in Lua

-- This program will register a menu that will open a window with a count of occurrences
-- of every address in the capture
do
local function menuable_tap()
-- Declare the window we will use
local tw = TextWindow.new("Address Counter")
-- This will contain a hash of counters of appearances of a certain address

local ips = {}
-- this is our tap

local tap = Listener.new();
function remove()
-- this way we remove the listener than otherwise will remain running indifinitelly
tap:remove();
end
-- we tell the window to call the remove() function when closed

tw:set_atclose(remove)
-- this function will be called once for each packet

function tap.packet(pinfo,tvb)
local src = ips[tostring(pinfo.src)] or 0
local dst = ips[tostring(pinfo.dst)] or 0
ips[tostring(pinfo.src)] = src + 1
ips[tostring(pinfo.dst)] = dst + 1
146
end
-- this function will be called once every few seconds to update our window
function tap.draw(t)
tw:clear()
for ip,num in pairs(ips) do
tw:append(ip .. "\t" .. num .. "\n");
end
end
-- this function will be called whenever a reset is needed

-- e.g. when reloading the capture file
function tap.reset()
tw:clear()
ips = {}
end
end
-- using this function we register our fuction

-- to be called when the user selects the Tools->Test->Packets menu
register_menu("Test/Packets", menuable_tap, MENU_TOOLS)
end
11.4. Wireshark's Lua API Reference Manual

This Part of the User Guide describes the Wireshark specific functions in the embedded Lua.
11.4.1. Saving capture files

11.4.1.1. Dumper
11.4.1.1.1. Dumper.new(filename, [filetype], [encap])
Creates a file to write packets. Dumper:new_for_current() will probably be a better choice.
11.4.1.1.1.1. Arguments
filename The name of the capture file to be created
filetype (optional) The type of the file to be created
encap (optional) The encapsulation to be used in the file to be created
11.4.1.1.1.2. Returns
The newly created Dumper object
11.4.1.1.1.3. Errors
• Not every filetype handles every encap
11.4.1.1.2. dumper:close()
Closes a dumper
11.4.1.1.2.1. Errors
• Cannot operate on a closed dumper
147
11.4.1.1.3. dumper:flush()
Writes all unsaved data of a dumper to the disk.
11.4.1.1.4. dumper:dump(timestamp, pseudoheader, bytearray)

Dumps an arbitrary packet. Note: Dumper:dump_current() will fit best in most cases.
11.4.1.1.4.1. Arguments
timestamp The absolute timestamp the packet will have
pseudoheader The Pseudoheader to use.
bytearray the data to be saved
11.4.1.1.5. dumper:new_for_current([filetype])
Creates a capture file using the same encapsulation as the one of the cuurrent packet
11.4.1.1.5.1. Arguments
filetype (optional) The file type. Defaults to pcap.
11.4.1.1.5.2. Returns
The newly created Dumper Object
11.4.1.1.5.3. Errors
• Cannot be used outside a tap or a dissector
11.4.1.1.6. dumper:dump_current()
Dumps the current packet as it is.
11.4.1.1.6.1. Errors
• Cannot be used outside a tap or a dissector
11.4.1.2. PseudoHeader
A pseudoheader to be used to save captured frames.
11.4.1.2.1. PseudoHeader.none()
Creates a "no" pseudoheader.
11.4.1.2.1.1. Returns
A null pseudoheader
11.4.1.2.2. PseudoHeader.eth([fcslen])
Creates an ethernet pseudoheader
11.4.1.2.2.1. Arguments
fcslen (optional) The fcs length
148
11.4.1.2.2.2. Returns
The ethernet pseudoheader
11.4.1.2.3. PseudoHeader.atm([aal], [vpi], [vci], [channel], [cells], [aal5u2u],

[aal5len])
Creates an ATM pseudoheader
11.4.1.2.3.1. Arguments
aal (optional) AAL number
vpi (optional) VPI
vci (optional) VCI
channel (optional) Channel
cells (optional) Number of cells in the PDU
aal5u2u (optional) AAL5 User to User indicator
aal5len (optional) AAL5 Len
11.4.1.2.3.2. Returns
The ATM pseudoheader
11.4.1.2.4. PseudoHeader.mtp2()
Creates an MTP2 PseudoHeader
11.4.1.2.4.1. Returns
The MTP2 pseudoheader
11.4.2. Obtaining dissection data

11.4.2.1. Field
A Field extractor to to obtain field values.
11.4.2.1.1. Field.new(fieldname)
Create a Field extractor
11.4.2.1.1.1. Arguments
fieldname The filter name of the field (e.g. ip.addr)
11.4.2.1.1.2. Returns
The field extractor
11.4.2.1.1.3. Errors
• A Field extractor must be defined before Taps or Dissectors get called
149
11.4.2.1.2. field:__call()
Obtain all values (see FieldInfo) for this field.
11.4.2.1.2.1. Returns
All the values of this field
11.4.2.1.2.2. Errors
• Fields cannot be used outside dissectors or taps
11.4.2.2. FieldInfo
An extracted Field
11.4.2.2.1. fieldinfo:__len()
Obtain the Length of the field
11.4.2.2.2. fieldinfo:__unm()
Obtain the Offset of the field
11.4.2.2.3. fieldinfo:__call()
Obtain the Value of the field
11.4.2.2.4. fieldinfo:__tostring()
The string representation of the field
11.4.2.2.5. fieldinfo:__eq()
Checks whether lhs is within rhs
11.4.2.2.5.1. Errors
• Data source must be the same for both fields
11.4.2.2.6. fieldinfo:__le()
Checks whether the end byte of lhs is before the end of rhs
11.4.2.2.7. fieldinfo:__lt()
Checks whether the end byte of rhs is before the beginning of rhs
11.4.2.2.7.1. Errors
• Data source must be the same for both fields
11.4.2.2.8. fieldinfo.name
The name of this field
150
11.4.2.2.9. fieldinfo.label
The string representing this field
11.4.2.2.10. fieldinfo.value
The value of this field
11.4.2.2.11. fieldinfo.len
The length of this field
11.4.2.2.12. fieldinfo.offset
The offset of this field
11.4.2.3. Non Method Functions

11.4.2.3.1. all_field_infos()
Obtain all fields from the current tree
11.4.2.3.1.1. Errors
• Cannot be called outside a listener or dissector
11.4.3. GUI support

11.4.3.1. ProgDlg
Manages a progress bar dialog.
11.4.3.1.1. ProgDlg.new([title], [task])

Creates a new TextWindow.
11.4.3.1.1.1. Arguments
title (optional) Title of the new window, defaults to "Progress".
task (optional) Current task, defaults to "".
11.4.3.1.1.2. Returns
The newly created TextWindow object.
11.4.3.1.2. progdlg:update(progress, [task])

Appends text
11.4.3.1.2.1. Arguments
progress Part done ( e.g. 0.75 ).
task (optional) Current task, defaults to "".
151
11.4.3.1.2.2. Errors
• Cannot be called for something not a ProgDlg
• Progress value out of range (must be between 0.0 and 1.0)
11.4.3.1.3. progdlg:stopped()
Checks wheher the user has pressed the stop button.
11.4.3.1.3.1. Returns
true if the user has asked to stop the progress.
11.4.3.1.3.2. Errors
11.4.3.1.4. progdlg:close()
Appends text
11.4.3.1.4.1. Errors
11.4.3.2. TextWindow
Manages a text window.
11.4.3.2.1. TextWindow.new([title])
Creates a new TextWindow.
11.4.3.2.1.1. Arguments
title (optional) Title of the new window.
11.4.3.2.1.2. Returns
The newly created TextWindow object.
11.4.3.2.2. textwindow:set_atclose(action)
Set the function that will be called when the window closes
11.4.3.2.2.1. Arguments
action A function to be executed when the user closes the window
11.4.3.2.2.2. Returns
The TextWindow object.
11.4.3.2.2.3. Errors
• Cannot be called for something not a TextWindow
152
11.4.3.2.3. textwindow:set(text)
Sets the text.
11.4.3.2.3.1. Arguments
text The text to be used.
11.4.3.2.3.2. Returns
11.4.3.2.3.3. Errors
11.4.3.2.4. textwindow:append(text)
Appends text
11.4.3.2.4.1. Arguments
text The text to be appended
11.4.3.2.4.2. Returns
11.4.3.2.4.3. Errors
11.4.3.2.5. textwindow:prepend(text)
Prepends text
11.4.3.2.5.1. Arguments
text The text to be appended
11.4.3.2.5.2. Returns
11.4.3.2.5.3. Errors
11.4.3.2.6. textwindow:clear()
Erases all text in the window.
11.4.3.2.6.1. Returns
11.4.3.2.6.2. Errors
153
11.4.3.2.7. textwindow:get_text()
Get the text of the window
11.4.3.2.7.1. Returns
The TextWindow's text.
11.4.3.2.7.2. Errors
11.4.3.2.8. textwindow:set_editable([editable])
Make this window editable
11.4.3.2.8.1. Arguments
editable (optional) A boolean flag, defaults to true
11.4.3.2.8.2. Returns
11.4.3.2.8.3. Errors
11.4.3.2.9. textwindow:add_button(label, function)

11.4.3.2.9.1. Arguments
label The label of the button
function The function to be called when clicked
11.4.3.2.9.2. Returns
11.4.3.2.9.3. Errors

11.4.3.3.1. gui_enabled()
Checks whether the GUI facility is enabled.
11.4.3.3.1.1. Returns
A boolean: true if it is enabled, false if it isn't.
11.4.3.3.2. register_menu(name, action, [group])

Register a menu item in one of the main menus.
154
11.4.3.3.2.1. Arguments
name The name of the menu item. The submenus are to be separated by '/'s. (string)
action The function to be called when the menu item is invoked. (function taking no
arguments and returning nothing)
group (optional) The menu group into which the menu item is to be
inserted. If omitted, defaults to MENU_STAT_GENERIC. One
of MENU_STAT_UNSORTED (Statistics), MENU_STAT_GENERIC
(Statistics, first section), MENU_STAT_CONVERSATION (Statistics/
Conversation List), MENU_STAT_ENDPOINT (Statistics/Endpoint
List), MENU_STAT_RESPONSE (Statistics/Service Response Time),
MENU_STAT_TELEPHONY (Telephony), MENU_ANALYZE (Analyze),
MENU_ANALYZE_CONVERSATION (Analyze/Conversation Filter),
MENU_TOOLS_UNSORTED (Tools). (number)
11.4.3.3.3. new_dialog(title, action, ...)

Pops up a new dialog
11.4.3.3.3.1. Arguments
title Title of the dialog's window.
action Action to be performed when OKd.
... A series of strings to be used as labels of the dialog's fields
11.4.3.3.3.2. Errors
• At least one field required
• All fields must be strings
11.4.3.3.4. retap_packets()
Rescan all packets and just run taps - don't reconstruct the display.
11.4.3.3.5. copy_to_clipboard(text)
Copy a string into the clipboard
11.4.3.3.5.1. Arguments
text The string to be copied into the clipboard.
11.4.3.3.6. open_capture_file(filename, filter)

Open and display a capture file
11.4.3.3.6.1. Arguments
filename The name of the file to be opened.
filter A filter to be applied as the file gets opened.
155
11.4.3.3.7. set_filter(text)
Set the main filter text
11.4.3.3.7.1. Arguments
text The filter's text.
11.4.3.3.8. apply_filter()
Apply the filter in the main filter box
11.4.3.3.9. reload()
Reload the current capture file
11.4.3.3.10. browser_open_url(url)
Open an url in a browser
11.4.3.3.10.1. Arguments
url The url.
11.4.3.3.11. browser_open_data_file(filename)
Open an file in a browser
11.4.3.3.11.1. Arguments
filename The url.
11.4.4. Post-dissection packet analysis

11.4.4.1. Listener
A Listener, is called once for every packet that matches a certain filter or has a certain tap. It can read the
tree, the packet's Tvb eventually the tapped data but it cannot add elements to the tree.
11.4.4.1.1. Listener.new([tap], [filter])

Creates a new Listener listener
11.4.4.1.1.1. Arguments
tap (optional) The name of this tap
filter (optional) A filter that when matches the tap.packet function gets called (use nil to be
called for every packet)
11.4.4.1.1.2. Returns
The newly created Listener listener object
11.4.4.1.1.3. Errors
• tap registration error
156
11.4.4.1.2. listener:remove()
Removes a tap listener
11.4.4.1.3. listener.packet
A function that will be called once every packet matches the Listener listener filter. function
tap.packet(pinfo,tvb,userdata) ... end
11.4.4.1.4. listener.draw
A function that will be called once every few seconds to redraw the gui objects in tshark this funtion is
called oly at the very end of the capture file. function tap.draw(userdata) ... end
11.4.4.1.5. listener.reset
A function that will be called at the end of the capture run. function tap.reset(userdata) ... end
11.4.5. Obtaining packet information

11.4.5.1. Address
Represents an address
11.4.5.1.1. Address.ip(hostname)
Creates an Address Object representing an IP address.
11.4.5.1.1.1. Arguments
hostname The address or name of the IP host.
11.4.5.1.1.2. Returns
The Address object
11.4.5.1.2. address:__tostring()
11.4.5.1.2.1. Returns
The string representing the address.
11.4.5.1.3. address:__eq()
Compares two Addresses
11.4.5.1.4. address:__le()
11.4.5.1.5. address:__lt()
11.4.5.2. Column
A Column in the packet list
157
11.4.5.2.1. column:__tostring()
11.4.5.2.1.1. Returns
A string representing the column
11.4.5.2.2. column:clear()
Clears a Column
11.4.5.2.3. column:set(text)
Sets the text of a Column
11.4.5.2.3.1. Arguments
text The text to which to set the Column
11.4.5.2.4. column:append(text)
Appends text to a Column
11.4.5.2.4.1. Arguments
text The text to append to the Column
11.4.5.2.5. column:preppend(text)
Prepends text to a Column
11.4.5.2.5.1. Arguments
text The text to prepend to the Column
11.4.5.3. Columns
The Columns of the packet list.
11.4.5.3.1. columns:__tostring()
11.4.5.3.1.1. Returns
The string "Columns", no real use, just for debugging purposes.
11.4.5.3.2. columns:__newindex(column, text)

Sets the text of a specific column
11.4.5.3.2.1. Arguments
column The name of the column to set
text The text for the column
11.4.5.4. Pinfo
Packet information
158
11.4.5.4.1. pinfo.number
The number of this packet in the current file
11.4.5.4.2. pinfo.len
The length of the frame
11.4.5.4.3. pinfo.caplen
The captured length of the frame
11.4.5.4.4. pinfo.abs_ts
When the packet was captured
11.4.5.4.5. pinfo.rel_ts
Number of seconds passed since beginning of capture
11.4.5.4.6. pinfo.delta_ts
Number of seconds passed since the last captured packet
11.4.5.4.7. pinfo.delta_dis_ts
Number of seconds passed since the last displayed packet
11.4.5.4.8. pinfo.visited
Whether this packet hass been already visited
11.4.5.4.9. pinfo.src
Source Address of this Packet
11.4.5.4.10. pinfo.dst
Destination Address of this Packet
11.4.5.4.11. pinfo.lo
lower Address of this Packet
11.4.5.4.12. pinfo.hi
higher Address of this Packet
11.4.5.4.13. pinfo.dl_src
Data Link Source Address of this Packet
11.4.5.4.14. pinfo.dl_dst
Data Link Destination Address of this Packet
159
11.4.5.4.15. pinfo.net_src
Network Layer Source Address of this Packet
11.4.5.4.16. pinfo.net_dst
Network Layer Destination Address of this Packet
11.4.5.4.17. pinfo.ptype
Type of Port of .src_port and .dst_port
11.4.5.4.18. pinfo.src_port
Source Port of this Packet
11.4.5.4.19. pinfo.dst_port
Source Address of this Packet
11.4.5.4.20. pinfo.ipproto
IP Protocol id
11.4.5.4.21. pinfo.circuit_id
For circuit based protocols
11.4.5.4.22. pinfo.match
Port/Data we are matching
11.4.5.4.23. pinfo.curr_proto
Which Protocol are we dissecting
11.4.5.4.24. pinfo.columns
Accesss to the packet list columns
11.4.5.4.25. pinfo.cols
Accesss to the packet list columns (equivalent to pinfo.columns)
11.4.5.4.26. pinfo.desegment_len
Estimated number of additional bytes required for completing the PDU
11.4.5.4.27. pinfo.desegment_offset
Offset in the tvbuff at which the dissector will continue processing when next called
11.4.5.4.28. pinfo.private_data
Access to private data
160
11.4.6. Functions for writing dissectors

11.4.6.1. Dissector
A refererence to a dissector, used to call a dissector against a packet or a part of it.
11.4.6.1.1. Dissector.get(name)
Obtains a dissector reference by name
11.4.6.1.1.1. Arguments
name The name of the dissector
11.4.6.1.1.2. Returns
The Dissector reference
11.4.6.1.2. dissector:call(tvb, pinfo, tree)

Calls a dissector against a given packet (or part of it)
11.4.6.1.2.1. Arguments
tvb The buffer to dissect
pinfo The packet info
tree The tree on which to add the protocol items
11.4.6.2. DissectorTable
A table of subdissectors of a particular protocol (e.g. TCP subdissectors like http, smtp, sip are added to
table "tcp.port"). Useful to add more dissectors to a table so that they appear in the Decode As... dialog.
11.4.6.2.1. DissectorTable.new(tablename, [uiname], [type], [base])

Creates a new DissectorTable for your dissector's use.
11.4.6.2.1.1. Arguments
tablename The short name of the table.
uiname (optional) The name of the table in the User Interface (defaults to the name given).
type (optional) Either FT_UINT* or FT_STRING (defaults to FT_UINT32)
base (optional) Either BASE_NONE, BASE_DEC, BASE_HEX, BASE_OCT,

BASE_DEC_HEX or BASE_HEX_DEC (defaults to BASE_DEC)
11.4.6.2.1.2. Returns
The newly created DissectorTable
11.4.6.2.2. DissectorTable.get(tablename)
Obtain a reference to an existing dissector table.
161
11.4.6.2.2.1. Arguments
tablename The short name of the table.
11.4.6.2.2.2. Returns
The DissectorTable
11.4.6.2.3. dissectortable:add(pattern, dissector)

Add a dissector to a table.
11.4.6.2.3.1. Arguments
pattern The pattern to match (either an integer or a string depending on the table's type).
dissector The dissector to add (either an Proto or a Dissector).
11.4.6.2.4. dissectortable:remove(pattern, dissector)

Remove a dissector from a table
11.4.6.2.4.1. Arguments
pattern The pattern to match (either an integer or a string depending on the table's type).
dissector The dissector to add (either an Proto or a Dissector).
11.4.6.2.5. dissectortable:try(pattern, tvb, pinfo, tree)

Try to call a dissector from a table
11.4.6.2.5.1. Arguments
pattern The pattern to be matched (either an integer or a string depending on the table's type).
tvb The buffer to dissect
pinfo The packet info
tree The tree on which to add the protocol items
11.4.6.2.6. dissectortable:get_dissector(pattern)
Try to obtain a dissector from a table.
11.4.6.2.6.1. Arguments
pattern The pattern to be matched (either an integer or a string depending on the table's type).
11.4.6.2.6.2. Returns
The dissector handle if found
nil if not found
11.4.6.3. Pref
A preference of a Protocol.
162
11.4.6.3.1. Pref.bool(label, default, descr)

Creates a boolean preference to be added to a Protocol's prefs table.
11.4.6.3.1.1. Arguments
label The Label (text in the right side of the preference input) for this preference
default The default value for this preference
descr A description of what this preference is
11.4.6.3.2. Pref.uint(label, default, descr)

Creates an (unsigned) integer preference to be added to a Protocol's prefs table.
11.4.6.3.2.1. Arguments
11.4.6.3.3. Pref.string(label, default, descr)

Creates a string preference to be added to a Protocol's prefs table.
11.4.6.3.3.1. Arguments
11.4.6.3.4. Pref.enum(label, default, descr, enum, radio)

Creates an enum preference to be added to a Protocol's prefs table.
11.4.6.3.4.1. Arguments
enum A enum table
radio Radio button (true) or Combobox (false)
11.4.6.3.5. Pref.range(label, default, descr, range, max)

Creates a range preference to be added to a Protocol's prefs table.
11.4.6.3.5.1. Arguments
163
range The range
max The maximum value
11.4.6.3.6. Pref.statictext(label, descr)

Creates a static text preference to be added to a Protocol's prefs table.
11.4.6.3.6.1. Arguments
label The static text
descr The static text description
11.4.6.4. Prefs
The table of preferences of a protocol
11.4.6.4.1. prefs:__newindex(name, pref)

Creates a new preference
11.4.6.4.1.1. Arguments
name The abbreviation of this preference
pref A valid but still unassigned Pref object
11.4.6.4.1.2. Errors
• Unknow Pref type
11.4.6.4.2. prefs:__index(name)
Get the value of a preference setting
11.4.6.4.2.1. Arguments
name The abbreviation of this preference
11.4.6.4.2.2. Returns
The current value of the preference
11.4.6.4.2.3. Errors
• Unknow Pref type
11.4.6.5. Proto
A new protocol in wireshark. Protocols have more uses, the main one is to dissect a protocol. But they can
be just dummies used to register preferences for other purposes.
164
11.4.6.5.1. Proto.new(name, desc)

11.4.6.5.1.1. Arguments
name The name of the protocol
desc A Long Text description of the protocol (usually lowercase)
11.4.6.5.1.2. Returns
The newly created protocol
11.4.6.5.2. proto.dissector
The protocol's dissector, a function you define
11.4.6.5.3. proto.fields
The Fields Table of this dissector
11.4.6.5.4. proto.prefs
The preferences of this dissector
11.4.6.5.5. proto.init
The init routine of this dissector, a function you define
11.4.6.5.6. proto.name
The name given to this dissector
11.4.6.6. ProtoField
A Protocol field (to be used when adding items to the dissection tree)
11.4.6.6.1. ProtoField.new(name, abbr, type, [valuestring], [base], [mask], [descr])

Creates a new field to be used in a protocol.
11.4.6.6.1.1. Arguments
name Actual name of the field (the string that appears in the tree).
abbr Filter name of the field (the string that is used in filters).
type Field Type (FT_*).
valuestring (optional) A ValueString object.
base (optional) The representation BASE_*.
mask (optional) The bitmask to be used.
descr (optional) The description of the field.
165
11.4.6.6.1.2. Returns
The newly created ProtoField object
11.4.6.6.2. ProtoField.uint8(abbr, [name], [base], [valuestring], [mask], [desc])

11.4.6.6.2.1. Arguments
abbr Abbreviated name of the field (the string used in filters)
name (optional) Actual name of the field (the string that appears in the tree)
base (optional) One of base.DEC, base.HEX or base.OCT
valuestring (optional) A table containing the text that corresponds to the values
mask (optional) Integer mask of this field
desc (optional) Description of the field
11.4.6.6.2.2. Returns
A protofield item to be added to a ProtoFieldArray

11.4.6.6.3.1. Arguments
11.4.6.6.3.2. Returns

11.4.6.6.4.1. Arguments
166
11.4.6.6.4.2. Returns

11.4.6.6.5.1. Arguments
11.4.6.6.5.2. Returns

11.4.6.6.6.1. Arguments
11.4.6.6.6.2. Returns
11.4.6.6.7. ProtoField.int8(abbr, [name], [base], [valuestring], [mask], [desc])

11.4.6.6.7.1. Arguments
167
11.4.6.6.7.2. Returns

11.4.6.6.8.1. Arguments
11.4.6.6.8.2. Returns

11.4.6.6.9.1. Arguments
11.4.6.6.9.2. Returns

11.4.6.6.10.1. Arguments
168
11.4.6.6.10.2. Returns

11.4.6.6.11.1. Arguments
11.4.6.6.11.2. Returns
11.4.6.6.12. ProtoField.framenum(abbr, [name], [base], [valuestring], [mask],

[desc])
A frame number (for hyperlinks between frames)
11.4.6.6.12.1. Arguments
11.4.6.6.12.2. Returns
11.4.6.6.13. ProtoField.ipv4(abbr, [name], [desc])

11.4.6.6.13.1. Arguments
169
11.4.6.6.13.2. Returns
11.4.6.6.14. ProtoField.ipv6(abbr, [name], [desc])

11.4.6.6.14.1. Arguments
11.4.6.6.14.2. Returns
11.4.6.6.15. ProtoField.ether(abbr, [name], [desc])

11.4.6.6.15.1. Arguments
11.4.6.6.15.2. Returns
11.4.6.6.16. ProtoField.float(abbr, [name], [desc])

11.4.6.6.16.1. Arguments
11.4.6.6.16.2. Returns
11.4.6.6.17. ProtoField.double(abbr, [name], [desc])

11.4.6.6.17.1. Arguments
170
11.4.6.6.17.2. Returns
11.4.6.6.18. ProtoField.string(abbr, [name], [desc])

11.4.6.6.18.1. Arguments
11.4.6.6.18.2. Returns
11.4.6.6.19. ProtoField.stringz(abbr, [name], [desc])

11.4.6.6.19.1. Arguments
11.4.6.6.19.2. Returns
11.4.6.6.20. ProtoField.bytes(abbr, [name], [desc])

11.4.6.6.20.1. Arguments
11.4.6.6.20.2. Returns
11.4.6.6.21. ProtoField.ubytes(abbr, [name], [desc])

11.4.6.6.21.1. Arguments
11.4.6.6.21.2. Returns
171
11.4.6.6.22. ProtoField.guid(abbr, [name], [desc])

11.4.6.6.22.1. Arguments
11.4.6.6.22.2. Returns
11.4.6.6.23. ProtoField.oid(abbr, [name], [desc])

11.4.6.6.23.1. Arguments
11.4.6.6.23.2. Returns
11.4.6.6.24. ProtoField.bool(abbr, [name], [desc])

11.4.6.6.24.1. Arguments
11.4.6.6.24.2. Returns

11.4.6.7.1. register_postdissector(proto)
Make a protocol (with a dissector) a postdissector. It will be called for every frame after dissection
11.4.6.7.1.1. Arguments
proto the protocol to be used as postdissector
11.4.7. Adding information to the dissection tree

11.4.7.1. TreeItem
TreeItems represent information in the packet-details pane. A root TreeItem is passed to dissectors as first
argument.
172
11.4.7.1.1. treeitem:add()
Adds an child item to a given item, returning the child. tree_item:add([proto_field | proto], [tvbrange],
[label], ...) if the proto_field represents a numeric value (int, uint or float) is to be treated as a Big Endian
(network order) Value.
11.4.7.1.1.1. Returns
The child item
11.4.7.1.2. treeitem:add_le()
Adds (and returns) an child item to a given item, returning the child. tree_item:add([proto_field | proto],
[tvbrange], [label], ...) if the proto_field represents a numeric value (int, uint or float) is to be treated as
a Little Endian Value.
11.4.7.1.2.1. Returns
The child item
11.4.7.1.3. treeitem:set_text(text)
Sets the text of the label
11.4.7.1.3.1. Arguments
text The text to be used.
11.4.7.1.4. treeitem:append_text(text)
Appends text to the label
11.4.7.1.4.1. Arguments
text The text to be appended.
11.4.7.1.5. treeitem:set_expert_flags([group], [severity])

Sets the expert flags of the item.
11.4.7.1.5.1. Arguments
group (optional) One of PI_CHECKSUM, PI_SEQUENCE, PI_RESPONSE_CODE,

PI_REQUEST_CODE, PI_UNDECODED, PI_REASSEMBLE,
PI_MALFORMED or PI_DEBUG
severity (optional) One of PI_CHAT, PI_NOTE, PI_WARN, PI_ERROR
11.4.7.1.6. treeitem:add_expert_info([group], [severity], [text])

Sets the expert flags of the item and adds expert info to the packet.
11.4.7.1.6.1. Arguments
group (optional) One of PI_CHECKSUM, PI_SEQUENCE, PI_RESPONSE_CODE,

PI_REQUEST_CODE, PI_UNDECODED, PI_REASSEMBLE,
PI_MALFORMED or PI_DEBUG
173
severity (optional) One of PI_CHAT, PI_NOTE, PI_WARN, PI_ERROR
text (optional) The text for the expert info
11.4.7.1.7. treeitem:set_generated()
Marks the TreeItem as a generated field (with data infered but not contained in the packet).
11.4.7.1.8. treeitem:set_hidden()
Should not be used
11.4.7.1.9. treeitem:set_len(len)
Set TreeItem's length inside tvb, after it has already been created.
11.4.7.1.9.1. Arguments
len The length to be used.
11.4.8. Functions for handling packet data

11.4.8.1. ByteArray
11.4.8.1.1. ByteArray.new([hexbytes])
Creates a ByteArray Object
11.4.8.1.1.1. Arguments
hexbytes (optional) A string consisting of hexadecimal bytes like "00 B1 A2" or "1a2b3c4d"
11.4.8.1.1.2. Returns
The new ByteArray object.
11.4.8.1.2. bytearray:__concat(first, second)

Concatenate two ByteArrays
11.4.8.1.2.1. Arguments
first First array
second Second array
11.4.8.1.2.2. Returns
The new composite ByteArray.
11.4.8.1.2.3. Errors
• Both arguments must be ByteArrays
11.4.8.1.3. bytearray:prepend(prepended)
Prepend a ByteArray to this ByteArray
174
11.4.8.1.3.1. Arguments
prepended Array to be prepended
11.4.8.1.3.2. Errors
11.4.8.1.4. bytearray:append(appended)
Append a ByteArray to this ByteArray
11.4.8.1.4.1. Arguments
appended Array to be appended
11.4.8.1.4.2. Errors
11.4.8.1.5. bytearray:set_size(size)
Sets the size of a ByteArray, either truncating it or filling it with zeros.
11.4.8.1.5.1. Arguments
size New size of the array
11.4.8.1.5.2. Errors
• ByteArray size must be non-negative
11.4.8.1.6. bytearray:set_index(index, value)

Sets the value of an index of a ByteArray.
11.4.8.1.6.1. Arguments
index The position of the byte to be set
value The char value to set [0-255]
11.4.8.1.7. bytearray:get_index(index)
Get the value of a byte in a ByteArray
11.4.8.1.7.1. Arguments
index The position of the byte to get
11.4.8.1.7.2. Returns
The value [0-255] of the byte.
11.4.8.1.8. bytearray:len()
Obtain the length of a ByteArray
175
11.4.8.1.8.1. Returns
The length of the ByteArray.
11.4.8.1.9. bytearray:subset(offset, length)

Obtain a segment of a ByteArray
11.4.8.1.9.1. Arguments
offset The position of the first byte
length The length of the segment
11.4.8.1.9.2. Returns
A ByteArray contaning the requested segment.
A string contaning a representaion of the ByteArray.
11.4.8.2. Int
Int64 represents a 64 bit integer. Lua uses one single number representation which can be chosen at compile
time and since it is often set to IEEE 754 double precision floating point, we cannot store a 64 bit integer
with full precision. For details, see: http://lua-users.org/wiki/FloatingPoint
11.4.8.3. Tvb
A Tvb represents the packet's buffer. It is passed as an argument to listeners and dissectors, and can be
used to extract information (via TvbRange) from the packet's data. Beware that Tvbs are usable only by the
current listener or dissector call and are destroyed as soon as the listener/dissector returns, so references to
them are unusable once the function has returned. To create a tvbrange the tvb must be called with offset
and length as optional arguments ( the offset defaults to 0 and the length to tvb:len() )
11.4.8.3.1. Tvb.new_real(bytearray, name)

Creates a new Tvb from a bytearray (it gets added to the current frame too)
11.4.8.3.1.1. Arguments
bytearray The data source for this Tvb.
name The name to be given to the new data-source.
11.4.8.3.1.2. Returns
The created Tvb.
11.4.8.3.2. Tvb.tvb(range)
Creates a (sub)Tvb from using a TvbRange
11.4.8.3.2.1. Arguments
range The TvbRange from which to create the new Tvb.
176
11.4.8.3.3. tvb:__tostring()
Convert the bytes of a Tvb into a string, to be used for debugging purposes as '...' will be appended in
case the string is too long.
11.4.8.3.3.1. Returns
The string.
11.4.8.3.4. tvb:len()
Obtain the length of a TVB
11.4.8.3.4.1. Returns
The length of the Tvb.
11.4.8.3.5. tvb:offset()
Returns the raw offset (from the beginning of the source Tvb) of a sub Tvb.
11.4.8.3.5.1. Returns
The raw offset of the Tvb.
11.4.8.3.6. tvb:__call()
Equivalent to tvb:range(...)
11.4.8.3.7. wslua:__concat()
Concatenate two objects to a string
11.4.8.4. TvbRange
A TvbRange represents an usable range of a Tvb and is used to extract data from the Tvb that generated it
TvbRanges are created by calling a tvb (e.g. tvb(offset,length)). If the TvbRange span is outside the Tvb's
range the creation will cause a runtime error.
11.4.8.4.1. tvb:range([offset], [length])

Creates a tvbr from this Tvb. This is used also as the Tvb:__call() metamethod.
11.4.8.4.1.1. Arguments
offset (optional) The offset (in octets) from the begining of the Tvb. Defaults to 0.
length (optional) The length (in octets) of the range. Defaults to until the end of the Tvb.
11.4.8.4.1.2. Returns
The TvbRange
11.4.8.4.2. tvbrange:uint()
Get a Big Endian (network order) unsigned integer from a TvbRange. The range must be 1, 2, 3 or 4
octets long.
177
11.4.8.4.2.1. Returns
The unsigned integer value
11.4.8.4.3. tvbrange:le_uint()
Get a Little Endian unsigned integer from a TvbRange. The range must be 1, 2, 3 or 4 octets long.
11.4.8.4.3.1. Returns
The unsigned integer value
11.4.8.4.4. tvbrange:uint64()
Get a Big Endian (network order) unsigned 64 bit integer from a TvbRange. The range must be 1-8 octets
long.
11.4.8.4.5. tvbrange:le_uint64()
Get a Little Endian unsigned 64 bit integer from a TvbRange. The range must be 1-8 octets long.
11.4.8.4.6. tvbrange:int()
Get a Big Endian (network order) signed integer from a TvbRange. The range must be 1, 2 or 4 octets long.
11.4.8.4.6.1. Returns
The signed integer value
11.4.8.4.7. tvbrange:le_int()
Get a Little Endian signed integer from a TvbRange. The range must be 1, 2 or 4 octets long.
11.4.8.4.7.1. Returns
The signed integer value
11.4.8.4.8. tvbrange:int64()
Get a Big Endian (network order) signed 64 bit integer from a TvbRange. The range must be 1-8 octets
long.
11.4.8.4.9. tvbrange:le_int64()
Get a Little Endian signed 64 bit integer from a TvbRange. The range must be 1-8 octets long.
11.4.8.4.10. tvbrange:float()
Get a Big Endian (network order) floating point number from a TvbRange. The range must be 4 or 8
octets long.
11.4.8.4.10.1. Returns
The floating point value
11.4.8.4.11. tvbrange:le_float()
Get a Little Endian floating point number from a TvbRange. The range must be 4 or 8 octets long.
178
11.4.8.4.11.1. Returns
The floating point value
11.4.8.4.12. tvbrange:ipv4()
Get an IPv4 Address from a TvbRange.
11.4.8.4.12.1. Returns
The IPv4 Address
11.4.8.4.13. tvbrange:le_ipv4()
Get an Little Endian IPv4 Address from a TvbRange.
11.4.8.4.13.1. Returns
The IPv4 Address
11.4.8.4.14. tvbrange:ether()
Get an Ethernet Address from a TvbRange.
11.4.8.4.14.1. Returns
The Ethernet Address
11.4.8.4.14.2. Errors
• The range must be 6 bytes long
11.4.8.4.15. tvbrange:string()
Obtain a string from a TvbRange
11.4.8.4.15.1. Returns
The string
11.4.8.4.16. tvbrange:stringz()
Obtain a zero terminated string from a TvbRange
11.4.8.4.16.1. Returns
The zero terminated string
11.4.8.4.17. tvbrange:bytes()
Obtain a ByteArray
11.4.8.4.17.1. Returns
The ByteArray
11.4.8.4.18. tvbrange:bitfield([position], [length])

Get a bitfield from a TvbRange.
179
11.4.8.4.18.1. Arguments
position (optional) The bit offset from the begining of the TvbRange. Defaults to 0.
length (optional) The length (in bits) of the field. Defaults to 1.
11.4.8.4.18.2. Returns
The bitfield value
11.4.8.4.19. tvbrange:range([offset], [length])

Creates a sub-TvbRange from this TvbRange. This is used also as the TvbRange:__call() metamethod.
11.4.8.4.19.1. Arguments
offset (optional) The offset (in octets) from the begining of the TvbRange. Defaults to 0.
length (optional) The length (in octets) of the range. Defaults to until the end of the TvbRange.
11.4.8.4.19.2. Returns
The TvbRange
11.4.8.4.20. tvbrange:len()
Obtain the length of a TvbRange
11.4.8.4.21. tvbrange:offset()
Obtain the offset in a TvbRange
11.4.8.4.22. tvbrange:__tostring()
Converts the TvbRange into a string. As the string gets truncated you should use this only for debugging
purposes or if what you want is to have a truncated string in the format 67:89:AB:...
11.4.8.5. UInt
UInt64 represents a 64 bit unsigned integer.
11.4.9. Utility Functions

11.4.9.1. Dir
A Directory
11.4.9.1.1. Dir.open(pathname, [extension])

Usage: for filename in Dir.open(path) do ... end
11.4.9.1.1.1. Arguments
pathname The pathname of the directory
180
extension (optional) If given, only file with this extension will be returned
11.4.9.1.1.2. Returns
the Dir object
11.4.9.1.2. dir:__call()
At every invocation will return one file (nil when done)
11.4.9.1.3. dir:close()
Closes the directory

11.4.9.2.1. format_date(timestamp)
Formats an absolute timestamp into a human readable date
11.4.9.2.1.1. Arguments
timestamp A timestamp value to convert.
11.4.9.2.1.2. Returns
A string with the formated date
11.4.9.2.2. format_time(timestamp)
Formats a relative timestamp in a human readable form
11.4.9.2.2.1. Arguments
timestamp A timestamp value to convert
11.4.9.2.2.2. Returns
A string with the formated time
11.4.9.2.3. report_failure(text)
Reports a failure to the user
11.4.9.2.3.1. Arguments
text Message
11.4.9.2.4. critical(...)
Will add a log entry with critical severity
11.4.9.2.4.1. Arguments
... objects to be printed
181
11.4.9.2.5. warn(...)
Will add a log entry with warn severity
11.4.9.2.5.1. Arguments
11.4.9.2.6. message(...)
Will add a log entry with message severity
11.4.9.2.6.1. Arguments
11.4.9.2.7. info(...)
Will add a log entry with info severity
11.4.9.2.7.1. Arguments
11.4.9.2.8. debug(...)
Will add a log entry with debug severity
11.4.9.2.8.1. Arguments
11.4.9.2.9. loadfile(filename)
Lua's loadfile() has been modified so that if a file does not exist in the current directory it will look for
it in wireshark's user and system directories
11.4.9.2.9.1. Arguments
filename Name of the file to be loaded
11.4.9.2.10. dofile(filename)
Lua's dofile() has been modified so that if a file does not exist in the current directory it will look for it
in wireshark's user and system directories
11.4.9.2.10.1. Arguments
filename Name of the file to be run
11.4.9.2.11. persconffile_path([filename])
11.4.9.2.11.1. Arguments
filename (optional) A filename
11.4.9.2.11.2. Returns
The full pathname for a file in the personal configuration directory
182
11.4.9.2.12. datafile_path([filename])
11.4.9.2.12.1. Arguments
filename (optional) A filename
11.4.9.2.12.2. Returns
The full pathname for a file in wireshark's configuration directory
11.4.9.2.13. register_stat_cmd_arg(argument, [action])

Register a function to handle a -z option
11.4.9.2.13.1. Arguments
argument Argument
action (optional) Action
183
Appendix A. Files and Folders
A.1. Capture Files
To understand which information will remain available after the captured packets are saved to a capture
file, it's helpful to know a bit about the capture file contents.
Wireshark uses the libpcap file format as the default format to save captured packets; this format has
existed for a long time and it's pretty simple. However, it has some drawbacks: it's not extensible and lacks
some information that would be really helpful (e.g. being able to add a comment to a packet such as "the
problems start here" would be really nice).
In addition to the libpcap format, Wireshark supports several different capture file formats. However, the
problems described above also applies for these formats.
A new capture file format "PCAP Next Generation Dump File Format" is currently under development,
which will fix these drawbacks. However, it still might take a while until the new file format is ready and
Wireshark can use it.
A.1.1. Libpcap File Contents

At the start of each libpcap capture file some basic information is stored like a magic number to identify
the libpcap file format. The most interesting information of this file start is the link layer type (Ethernet,
Token Ring, ...).
The following data is saved for each packet:
• the timestamp with millisecond resolution
• the packet length as it was "on the wire"
• the packet length as it's saved in the file
• the packet's raw bytes
A detailed description of the libpcap file format can be found at: http://wiki.wireshark.org/Development/
LibpcapFileFormat
A.1.2. Not Saved in the Capture File

Probably even more interesting for everyday Wireshark usage is to know the things that are not saved
in the capture file:
• current selections (selected packet, ...)
• name resolution information, see Section 7.7, “Name Resolution” for details
Warning!
The name resolution information is rebuilt each time Wireshark is restarted so this
information might even change when the capture file is reopened on the same machine
later!
184
Files and Folders
• the number of packets dropped while capturing
• packet marks set with "Edit/Mark Packet"
• time references set with "Edit/Time Reference"
• the current display filter
• ...
A.2. Configuration Files and Folders

Wireshark uses a number of files and folders while it is running. Some of these reside in the personal
configuration folder and are used to maintain information between runs of Wireshark, while some of them
are maintained in system areas.
Tip
A list of the folders Wireshark actually uses can be found under the Folders tab in the dialog
box shown when you select About Wireshark from the Help menu.
The content format of the configuration files is the same on all platforms. However, to match the different
policies for Unix and Windows platforms, different folders are used for these files.
185
Files and Folders
Table A.1. Configuration files and folders overview
File/Folder Description Unix/Linux Windows folders

folders
preferences Settings from the /etc/ %WIRESHARK%\wireshark.conf,
Preferences dialog wireshark.conf, %APPDATA%\Wireshark\preferences
box. $HOME/.wireshark/
preferences
recent Recent GUI $HOME/.wireshark/%APPDATA%\Wireshark\recent
settings (e.g. recent
recent files lists).
cfilters Capture filters. $HOME/.wireshark/%WIRESHARK%\cfilters, %APPDATA%
cfilters \Wireshark\cfilters
dfilters Display filters. $HOME/.wireshark/%WIRESHARK%\dfilters, %APPDATA%
dfilters \Wireshark\dfilters
colorfilters Coloring rules. $HOME/.wireshark/%WIRESHARK%\colorfilters, %APPDATA
colorfilters %\Wireshark\colorfilters
disabled_protos Disabled $HOME/.wireshark/%WIRESHARK%\disabled_protos,
protocols. disabled_protos %APPDATA%\Wireshark\disabled_protos
ethers Ethernet name /etc/ethers, %WIRESHARK%\ethers, %APPDATA%
resolution. $HOME/.wireshark/\Wireshark\ethers
ethers
manuf Ethernet name /etc/manuf, %WIRESHARK%\manuf, %APPDATA%
resolution. $HOME/.wireshark/\Wireshark\manuf
manuf
hosts IPv4 and IPv6 /etc/hosts, %WIRESHARK%\hosts, %APPDATA%
name resolution. $HOME/.wireshark/\Wireshark\hosts
hosts
services Network services. /etc/services, %WIRESHARK%\services, %APPDATA%
$HOME/.wireshark/\Wireshark\services
services
subnets IPv4 subnet name /etc/subnets, %WIRESHARK%\subnets, %APPDATA%
resolution. $HOME/.wireshark/\Wireshark\subnets
subnets
ipxnets IPX name /etc/ipxnets, %WIRESHARK%\ipxnets, %APPDATA%
resolution. $HOME/.wireshark/\Wireshark\ipxnets
ipxnets
plugins Plugin directories. /usr/share/ %WIRESHARK%\plugins\<version>,
wireshark/ %APPDATA%\Wireshark\plugins
plugins, /usr/local/
share/wireshark/
plugins,
$HOME/.wireshark/
plugins
temp Temporary files. Environment: Environment: TMPDIR or TEMP
TMPDIR
186
Files and Folders
Windows folders
%APPDATA% points to the personal configuration folder, e.g.: C:\Documents
and Settings\<username>\Application Data (details can be found at:
Section A.3.1, “Windows profiles”),
%WIRESHARK% points to the Wireshark program folder, e.g.: C:\Program Files

\Wireshark
Unix/Linux folders
The /etc folder is the global Wireshark configuration folder. The folder actually used on
your system may vary, maybe something like: /usr/local/etc.
$HOME is usually something like: /home/<username>
preferences/wireshark.conf This file contains your Wireshark preferences, including defaults

for capturing and displaying packets. It is a simple text file
containing statements of the form:
variable: value
The settings from this file are read in at program start and written
to disk when you press the Save button in the "Preferences" dialog
box.
recent This file contains various GUI related settings like the main window
position and size, the recent files list and such. It is a simple text
file containing statements of the form:
variable: value
It is read at program start and written at program exit.
cfilters This file contains all the capture filters that you have defined and
saved. It consists of one or more lines, where each line has the
following format:
"<filter name>" <filter string>
The settings from this file are read in at program start and written to
disk when you press the Save button in the "Capture Filters" dialog
box.
dfilters This file contains all the display filters that you have defined and
following format:
"<filter name>" <filter string>
187
Files and Folders
disk when you press the Save button in the "Display Filters" dialog
box.
colorfilters This file contains all the color filters that you have defined and
following format:
@<filter name>@<filter string>@[<bg RGB(16-bit)>][<fg RGB(16-bit)>]
disk when you press the Save button in the "Coloring Rules" dialog
box.
disabled_protos Each line in this file specifies a disabled protocol name. The
following are some examples:
tcp
udp
The settings from this file are read in at program start and written
to disk when you press the Save button in the "Enabled Protocols"
dialog box.
ethers When Wireshark is trying to translate Ethernet hardware addresses

to names, it consults the files listed in Table A.1, “Configuration
files and folders overview”. If an address is not found in /etc/ethers,
Wireshark looks in $HOME/.wireshark/ethers
Each line in these files consists of one hardware address and name
separated by whitespace. The digits of hardware addresses are
separated by colons (:), dashes (-) or periods(.). The following are
some examples:
ff-ff-ff-ff-ff-ff Broadcast
c0-00-ff-ff-ff-ff TR_broadcast
00.2b.08.93.4b.a1 Freds_machine
The settings from this file are read in at program start and never
written by Wireshark.
manuf Wireshark uses the files listed in Table A.1, “Configuration files
and folders overview” to translate the first three bytes of an Ethernet
address into a manufacturers name. This file has the same format
as the ethers file, except addresses are three bytes long.
An example is:
00:00:01 Xerox # XEROX CORPORATION
188
Files and Folders
hosts Wireshark uses the files listed in Table A.1, “Configuration files
and folders overview” to translate IPv4 and IPv6 addresses into
names.
This file has the same format as the usual /etc/hosts file on Unix
systems.
An example is:
# Comments must be prepended by the # sign!

192.168.0.1 homeserver
services Wireshark uses the files listed in Table A.1, “Configuration files
and folders overview” to translate port numbers into names.
An example is:
mydns 5045/udp # My own Domain Name Server

mydns 5045/tcp # My own Domain Name Server
subnets Wireshark uses the files listed in Table A.1, “Configuration files
and folders overview” to translate an IPv4 address into a subnet
name. If no exact match from the hosts file or from DNS is found,
Wireshark will attempt a partial match for the subnet of the address.
Each line of this file consists of an IPv4 address, a subnet mask

length separated only by a '/' and a name separated by whitespace.
While the address must be a full IPv4 address, any values beyond
the mask length are subsequently ignored.
An example is:
# Comments must be prepended by the # sign!

192.168.0.0/24 ws_test_network
A partially matched name will be printed as "subnet-

name.remaining-address". For example, "192.168.0.1" under the
subnet above would be printed as "ws_test_network.1"; if the mask
length above had been 16 rather than 24, the printed address would
be "ws_test_network.0.1".
ipxnets Wireshark uses the files listed in Table A.1, “Configuration files
and folders overview” to translate IPX network numbers into
names.
189
Files and Folders
An example is:
C0.A8.2C.00 HR
c0-a8-1c-00 CEO
00:00:BE:EF IT_Server1
110f FileServer3
plugins folder Wireshark searches for plugins in the directories listed in Table A.1,
“Configuration files and folders overview”. They are searched in
the order listed.
temp folder If you start a new capture and don't specify a filename for it,
Wireshark uses this directory to store that file; see Section 4.8,
“Capture files and file modes”.
A.3. Windows folders

Here you will find some details about the folders used in Wireshark on different Windows versions.
As already mentioned, you can find the currently used folders in the About Wireshark dialog.
A.3.1. Windows profiles

Windows uses some special directories to store user configuration files which define the "user profile".
This can be confusing, as the default directory location changed from Windows version to version and
might also be different for English and internationalized versions of Windows.
Note!
If you've upgraded to a new Windows version, your profile might be kept in the former
location, so the defaults mentioned here might not apply.
The following guides you to the right place where to look for Wireshark's profile data.
Vista C:\Users\<username>\AppData\Roaming
\Wireshark
XP/2000 C:\Documents and Settings\<username>

\Application Data, "Documents and Settings" and
"Application Data" might be internationalized.
NT 4 (no longer supported by C:\WINNT\Profiles\<username>\Application

Wireshark) Data\Wireshark
ME/98 - with enabled user In Windows ME and 98 you can enable separate user
profiles (no longer supported by profiles. In that case, something like: C:\windows\Profiles
Wireshark) \<username>\Application Data\Wireshark is used.
ME/98/95 (no longer supported The default in Windows ME/98/95 is: all users work with the
by Wireshark) same profile, which is located at: C:\windows\Application
Data\Wireshark
190
Files and Folders
A.3.2. Windows Vista/XP/2000/NT roaming profiles

The following will only be applicable if you are using roaming profiles. This might be the case, if you
work in a Windows domain environment (used in company networks). The configurations of all programs
you use won't be saved on the local hard drive of the computer you are currently working on, but on the
domain server.
As Wireshark is using the correct places to store its profile data, your settings will travel with you, if you
logon to a different computer the next time.
There is an exception to this: The "Local Settings" folder in your profile data (typically something like:
C:\Documents and Settings\<username>\Local Settings) will not be transferred to the
domain server. This is the default for temporary capture files.
A.3.3. Windows temporary folder

Wireshark uses the folder which is set by the TMPDIR or TEMP environment variable. This variable will
be set by the Windows installer.
Vista XXX - could someone give information about this?
XP/2000 C:\Documents and Settings\<username>\Local Settings\Temp
NT 4 C:\TEMP
191
Appendix B. Protocols and Protocol
Fields
Wireshark distinguishes between protocols (e.g. tcp) and protocol fields (e.g. tcp.port).
A comprehensive list of all protocols and protocol fields can be found at: http://www.wireshark.org/docs/
dfref/
192
Appendix C. Wireshark Messages
Wireshark provides you with additional information generated out of the plain packet data or it may need
to indicate dissection problems. Messages generated by Wireshark are usually placed in [] parentheses.
C.1. Packet List Messages

These messages might appear in the packet list.
C.1.1. [Malformed Packet]

Malformed packet means that the protocol dissector can't dissect the contents of the packet any further.
There can be various reasons:
• Wrong dissector: Wireshark erroneously has chosen the wrong protocol dissector for this packet. This
will happen e.g. if you are using a protocol not on its well known TCP or UDP port. You may try
Analyze|Decode As to circumvent this problem.
• Packet not reassembled: The packet is longer than a single frame and it is not reassembled, see
Section 7.6, “Packet Reassembling” for further details.
• Packet is malformed: The packet is actually wrong (malformed), meaning that a part of the packet is
just not as expected (not following the protocol specifications).
• Dissector is buggy: The corresponding protocol dissector is simply buggy or still incomplete.
Any of the above is possible. You'll have to look into the specific situation to determine the reason. You
could disable the dissector by disabling the protocol on the Analyze menu and check how Wireshark
displays the packet then. You could (if it's TCP) enable reassembly for TCP and the specific dissector
(if possible) in the Edit|Preferences menu. You could check the packet contents yourself by reading the
packet bytes and comparing it to the protocol specification. This could reveal a dissector bug. Or you could
find out that the packet is indeed wrong.
C.1.2. [Packet size limited during capture]

The packet size was limited during capture, see "Limit each packet to n bytes" at the Section 4.5, “The
"Capture Options" dialog box”. While dissecting, the current protocol dissector was simply running out of
packet bytes and had to give up. There's nothing else you can do now, except to repeat the whole capture
process again with a higher (or no) packet size limitation.
C.2. Packet Details Messages

These messages might appear in the packet details.
C.2.1. [Response in frame: 123]

The current packet is the request of a detected request/response pair. You can directly jump to the
corresponding response packet just by double clicking on this message.
C.2.2. [Request in frame: 123]

Same as "Response in frame: 123" above, but the other way round.
193
Wireshark Messages
C.2.3. [Time from request: 0.123 seconds]

The time between the request and the response packets.
C.2.4. [Stream setup by PROTOCOL (frame 123)]

The session control protocol (SDP, H225, etc) message which signaled the creation of this session. You
can directly jump to the corresponding packet just by double clicking on this message.
194
Appendix D. Related command line
tools
D.1. Introduction
Besides the Wireshark GUI application, there are some command line tools which can be helpful for doing
some more specialized things. These tools will be described in this chapter.
D.2. tshark: Terminal-based Wireshark

TShark is a terminal oriented version of Wireshark designed for capturing and displaying packets when
an interactive user interface isn't necessary or available. It supports the same options as wireshark. For
more information on tshark, see the manual pages (man tshark).
D.3. tcpdump: Capturing with tcpdump for

viewing with Wireshark
There are occasions when you want to capture packets using tcpdump rather than wireshark, especially
when you want to do a remote capture and do not want the network load associated with running Wireshark
remotely (not to mention all the X traffic polluting your capture).
However, the default tcpdump parameters result in a capture file where each packet is truncated, because
most versions of tcpdump, will, by default, only capture the first 68 or 96 bytes of each packet.
To ensure that you capture complete packets, use the following command:
tcpdump -i <interface> -s 65535 -w <some-file>
You will have to specify the correct interface and the name of a file to save into. In addition, you will
have to terminate the capture with ^C when you believe you have captured enough packets.
Note!
tcpdump is not part of the Wireshark distribution. You can get it from: http://
www.tcpdump.org for various platforms.
D.4. dumpcap: Capturing with dumpcap for

viewing with Wireshark
Dumpcap is a network traffic dump tool. It captures packet data from a live network and writes the
packets to a file. Dumpcap's native capture file format is libpcap format, which is also the format used by
Wireshark, tcpdump and various other tools.
Without any options set it will use the pcap library to capture traffic from the first available network
interface and write the received raw packet data, along with the packets' time stamps into a libpcap file.
195
Related command line tools
Packet capturing is performed with the pcap library. The capture filter syntax follows the rules of the pcap
library.
Example D.1. Help information available from dumpcap
dumpcap -h
Dumpcap 1.1.4
Capture network packets and dump them into a libpcap file.
Usage: dumpcap [options] ...
Capture interface:
-i <interface> name or idx of interface (def: first non-loopback)
-f <capture filter> packet filter in libpcap filter syntax
-s <snaplen> packet snapshot length (def: 65535)
-p don't capture in promiscuous mode
-B <buffer size> size of kernel buffer (def: 1MB)
-y <link type> link layer type (def: first appropriate)
-D print list of interfaces and exit
-L print list of link-layer types of iface and exit
-S print statistics for each interface once every second
-M for -D, -L, and -S produce machine-readable output
Stop conditions:
-c <packet count> stop after n packets (def: infinite)
-a <autostop cond.> ... duration:NUM - stop after NUM seconds
filesize:NUM - stop this file after NUM KB
files:NUM - stop after NUM files
Output (files):
-w <filename> name of file to save (def: tempfile)
-b <ringbuffer opt.> ... duration:NUM - switch to next file after NUM secs
filesize:NUM - switch to next file after NUM KB
files:NUM - ringbuffer: replace after NUM files
-n use pcapng format instead of pcap
Miscellaneous:
-v print version information and exit
Example: dumpcap -i eth0 -a duration:60 -w output.pcap

"Capture network packets from interface eth0 until 60s passed into output.pcap"
Use Ctrl-C to stop capturing at any time.
D.5. capinfos: Print information about capture

files
Included with Wireshark is a small utility called capinfos, which is a command-line utility to print
information about binary capture files.
196
Example D.2. Help information available from capinfos
$ capinfos -h
Capinfos 1.1.4
Prints information about capture files.
Usage: capinfos [options] <infile> ...
General:
-t display the capture file type
-E display the capture file encapsulation
Size:
-c display the number of packets
-s display the size of the file (in bytes)
-d display the total length of all packets (in bytes)
Time:
-u display the capture duration (in seconds)
-a display the capture start time
-e display the capture end time
Statistic:
-y display average data rate (in bytes/sec)
-i display average data rate (in bits/sec)
-z display average packet size (in bytes)
-x display average packet rate (in packets/sec)
Miscellaneous:
If no options are given the default is to display all infos
D.6. editcap: Edit capture files

Included with Wireshark is a small utility called editcap, which is a command-line utility for working with
capture files. Its main function is to remove packets from capture files, but it can also be used to convert
capture files from one format to another, as well as to print information about capture files.
197
Example D.3. Help information available from editcap
$ editcap -h
Editcap 1.1.4
Edit and/or translate the format of capture files.
Usage: editcap [options] ... <infile> <outfile> [ <packet#>[-<packet#>] ... ]
<infile> and <outfile> must both be present.

A single packet or a range of packets can be selected.
Packet selection:
-r keep the selected packets; default is to delete them.
-A <start time> don't output packets whose timestamp is before the
given time (format as YYYY-MM-DD hh:mm:ss).
-B <stop time> don't output packets whose timestamp is after the
given time (format as YYYY-MM-DD hh:mm:ss).
Duplicate packet removal:

-d remove packet if duplicate (window == 5).
-D <dup window> remove packet if duplicate; configurable <dup window>
Valid <dup window> values are 0 to 1000000.
NOTE: A <dup window> of 0 with -v (verbose option) is
useful to print MD5 hashes.
-w <dup time window> remove packet if duplicate packet is found EQUAL TO OR
LESS THAN <dup time window> prior to current packet.
A <dup time window> is specified in relative seconds
(e.g. 0.000001).
NOTE: The use of the 'Duplicate packet removal' options with

other editcap options except -v may not always work as expected.
Specifically the -r and -t options will very likely NOT have the
desired effect if combined with the -d, -D or -w.
Packet manipulation:
-s <snaplen> truncate each packet to max. <snaplen> bytes of data.
-C <choplen> chop each packet at the end by <choplen> bytes.
-t <time adjustment> adjust the timestamp of each packet;
<time adjustment> is in relative seconds (e.g. -0.5).
-E <error probability> set the probability (between 0.0 and 1.0 incl.)
that a particular packet byte will be randomly changed.
Output File(s):
-c <packets per file> split the packet output to different files
based on uniform packet counts
with a maximum of <packets per file> each.
-i <seconds per file> split the packet output to different files
based on uniform time intervals
with a maximum of <seconds per file> each.
-F <capture type> set the output file type; default is libpcap.
an empty "-F" option will list the file types.
-T <encap type> set the output file encapsulation type;
default is the same as the input file.
an empty "-T" option will list the encapsulation types.
Miscellaneous:
-h display this help and exit.
-v verbose output.
If -v is used with any of the 'Duplicate Packet
Removal' options (-d, -D or -w) then Packet lengths
and MD5 hashes are printed to standard-out.
198
Example D.4. Capture file types available from editcap
$ editcap -F
editcap: option requires an argument -- F
editcap: The available capture file types for "F":
libpcap - Wireshark/tcpdump/... - libpcap
nseclibpcap - Wireshark - nanosecond libpcap
modlibpcap - Modified tcpdump - libpcap
nokialibpcap - Nokia tcpdump - libpcap
rh6_1libpcap - RedHat 6.1 tcpdump - libpcap
suse6_3libpcap - SuSE 6.3 tcpdump - libpcap
5views - Accellent 5Views capture
dct2000 - Catapult DCT2000 trace (.out format)
nettl - HP-UX nettl trace
netmon1 - Microsoft NetMon 1.x
netmon2 - Microsoft NetMon 2.x
ngsniffer - NA Sniffer (DOS)
ngwsniffer_1_1 - NA Sniffer (Windows) 1.1
ngwsniffer_2_0 - NA Sniffer (Windows) 2.00x
niobserverv9 - Network Instruments Observer (V9)
lanalyzer - Novell LANalyzer
snoop - Sun snoop
rf5 - Tektronix K12xx 32-bit .rf5 format
visual - Visual Networks traffic capture
k12text - K12 text file
commview - TamoSoft CommView
pcapng - Wireshark - pcapng (experimental)
Example D.5. Encapsulation types available from editcap
$ editcap -T
editcap: option requires an argument -- T
editcap: The available encapsulation types for "T":
ether - Ethernet
tr - Token Ring
slip - SLIP
ppp - PPP
fddi - FDDI
fddi-swapped - FDDI with bit-swapped MAC addresses
rawip - Raw IP
arcnet - ARCNET
arcnet_linux - Linux ARCNET
atm-rfc1483 - RFC 1483 ATM
linux-atm-clip - Linux ATM CLIP
lapb - LAPB
atm-pdus - ATM PDUs
atm-pdus-untruncated - ATM PDUs - untruncated
null - NULL
ascend - Lucent/Ascend access equipment
isdn - ISDN
ip-over-fc - RFC 2625 IP-over-Fibre Channel
ppp-with-direction - PPP with Directional Info
ieee-802-11 - IEEE 802.11 Wireless LAN
prism - IEEE 802.11 plus Prism II monitor mode header
ieee-802-11-radio - IEEE 802.11 Wireless LAN with radio information
ieee-802-11-radiotap - IEEE 802.11 plus radiotap WLAN header
ieee-802-11-avs - IEEE 802.11 plus AVS WLAN header
linux-sll - Linux cooked-mode capture
frelay - Frame Relay
frelay-with-direction - Frame Relay with Directional Info
chdlc - Cisco HDLC
ios - Cisco IOS internal
ltalk - Localtalk
199
pflog-old - OpenBSD PF Firewall logs, pre-3.4

hhdlc - HiPath HDLC
docsis - Data Over Cable Service Interface Specification
cosine - CoSine L2 debug log
whdlc - Wellfleet HDLC
sdlc - SDLC
tzsp - Tazmen sniffer protocol
enc - OpenBSD enc(4) encapsulating interface
pflog - OpenBSD PF Firewall logs
chdlc-with-direction - Cisco HDLC with Directional Info
bluetooth-h4 - Bluetooth H4
mtp2 - SS7 MTP2
mtp3 - SS7 MTP3
irda - IrDA
user0 - USER 0
user1 - USER 1
user2 - USER 2
user3 - USER 3
user4 - USER 4
user5 - USER 5
user6 - USER 6
user7 - USER 7
user8 - USER 8
user9 - USER 9
user10 - USER 10
user11 - USER 11
user12 - USER 12
user13 - USER 13
user14 - USER 14
user15 - USER 15
symantec - Symantec Enterprise Firewall
ap1394 - Apple IP-over-IEEE 1394
bacnet-ms-tp - BACnet MS/TP
raw-icmp-nettl - Raw ICMP with nettl headers
raw-icmpv6-nettl - Raw ICMPv6 with nettl headers
gprs-llc - GPRS LLC
juniper-atm1 - Juniper ATM1
juniper-atm2 - Juniper ATM2
redback - Redback SmartEdge
rawip-nettl - Raw IP with nettl headers
ether-nettl - Ethernet with nettl headers
tr-nettl - Token Ring with nettl headers
fddi-nettl - FDDI with nettl headers
unknown-nettl - Unknown link-layer type with nettl headers
mtp2-with-phdr - MTP2 with pseudoheader
juniper-pppoe - Juniper PPPoE
gcom-tie1 - GCOM TIE1
gcom-serial - GCOM Serial
x25-nettl - X25 with nettl headers
k12 - K12 protocol analyzer
juniper-mlppp - Juniper MLPPP
juniper-mlfr - Juniper MLFR
juniper-ether - Juniper Ethernet
juniper-ppp - Juniper PPP
juniper-frelay - Juniper Frame-Relay
juniper-chdlc - Juniper C-HDLC
juniper-ggsn - Juniper GGSN
lapd - LAPD
dct2000 - Catapult DCT2000
ber - ASN.1 Basic Encoding Rules
juniper-vp - Juniper Voice PIC
usb - Raw USB packets
ieee-802-16-mac-cps - IEEE 802.16 MAC Common Part Sublayer
raw-telnet-nettl - Raw telnet with nettl headers
usb-linux - USB packets with Linux header
mpeg - MPEG
ppi - Per-Packet Information header
200
erf - Endace Record File

bluetooth-h4 - Bluetooth H4 with linux header
sita-wan - SITA WAN packets
sccp - SS7 SCCP
bluetooth-hci - Bluetooth without transport layer
ipmb - Intelligent Platform Management Bus
wpan - IEEE 802.15.4 Wireless PAN
x2e-xoraya - X2E Xoraya
flexray - FlexRay
lin - Local Interconnect Network
most - Media Oriented Systems Transport
can20b - Controller Area Network 2.0B
layer1-event - EyeSDN Layer 1 event
x2e-serial - X2E serial line capture
i2c - I2C
wpan-nonask-phy - IEEE 802.15.4 Wireless PAN non-ASK PHY
tnef - Transport-Neutral Encapsulation Format
usb-linux-mmap - USB packets with Linux header and padding
gsm_um - GSM Um Interface
D.7. mergecap: Merging multiple capture files

into one
Mergecap is a program that combines multiple saved capture files into a single output file specified by
the -w argument. Mergecap knows how to read libpcap capture files, including those of tcpdump. In
addition, Mergecap can read capture files from snoop (including Shomiti) and atmsnoop, LanAlyzer,
Sniffer (compressed or uncompressed), Microsoft Network Monitor, AIX's iptrace, NetXray, Sniffer Pro,
RADCOM's WAN/LAN analyzer, Lucent/Ascend router debug output, HP-UX's nettl, and the dump
output from Toshiba's ISDN routers. There is no need to tell Mergecap what type of file you are reading;
it will determine the file type by itself. Mergecap is also capable of reading any of these file formats if
they are compressed using gzip. Mergecap recognizes this directly from the file; the '.gz' extension is not
required for this purpose.
By default, it writes the capture file in libpcap format, and writes all of the packets in the input capture
files to the output file. The -F flag can be used to specify the format in which to write the capture file; it can
write the file in libpcap format (standard libpcap format, a modified format used by some patched versions
of libpcap, the format used by Red Hat Linux 6.1, or the format used by SuSE Linux 6.3), snoop format,
uncompressed Sniffer format, Microsoft Network Monitor 1.x format, and the format used by Windows-
based versions of the Sniffer software.
Packets from the input files are merged in chronological order based on each frame's timestamp, unless
the -a flag is specified. Mergecap assumes that frames within a single capture file are already stored in
chronological order. When the -a flag is specified, packets are copied directly from each input file to the
output file, independent of each frame's timestamp.
If the -s flag is used to specify a snapshot length, frames in the input file with more captured data than
the specified snapshot length will have only the amount of data specified by the snapshot length written
to the output file. This may be useful if the program that is to read the output file cannot handle packets
larger than a certain size (for example, the versions of snoop in Solaris 2.5.1 and Solaris 2.6 appear to
reject Ethernet frames larger than the standard Ethernet MTU, making them incapable of handling gigabit
Ethernet captures if jumbo frames were used).
If the -T flag is used to specify an encapsulation type, the encapsulation type of the output capture file will
be forced to the specified type, rather than being the type appropriate to the encapsulation type of the input
capture file. Note that this merely forces the encapsulation type of the output file to be the specified type;
201
the packet headers of the packets will not be translated from the encapsulation type of the input capture
file to the specified encapsulation type (for example, it will not translate an Ethernet capture to an FDDI
capture if an Ethernet capture is read and '-T fddi' is specified).
Example D.6. Help information available from mergecap
$ mergecap -h
Mergecap 1.1.4
Merge two or more capture files into one.
Usage: mergecap [options] -w <outfile>|- <infile> ...
Output:
-a concatenate rather than merge files.
default is to merge based on frame timestamps.
-s <snaplen> truncate packets to <snaplen> bytes of data.
-w <outfile>|- set the output filename to <outfile> or '-' for stdout.
-F <capture type> set the output file type; default is libpcap.
an empty "-F" option will list the file types.
-T <encap type> set the output file encapsulation type;
default is the same as the first input file.
an empty "-T" option will list the encapsulation types.
Miscellaneous:
-v verbose output.
A simple example merging dhcp-capture.libpcap and imap-1.libpcap into

outfile.libpcap is shown below.
Example D.7. Simple example of using mergecap

$ mergecap -w outfile.libpcap dhcp-capture.libpcap imap-1.libpcap
D.8. text2pcap: Converting ASCII hexdumps to

network captures
There may be some occasions when you wish to convert a hex dump of some network traffic into a libpcap
file.
Text2pcap is a program that reads in an ASCII hex dump and writes the data described into a libpcap-
style capture file. text2pcap can read hexdumps with multiple packets in them, and build a capture file of
multiple packets. text2pcap is also capable of generating dummy Ethernet, IP and UDP headers, in order
to build fully processable packet dumps from hexdumps of application-level data only.
Text2pcap understands a hexdump of the form generated by od -A x -t x1. In other words, each byte is
individually displayed and surrounded with a space. Each line begins with an offset describing the position
in the file. The offset is a hex number (can also be octal - see -o), of more than two hex digits. Here is a
sample dump that text2pcap can recognize:
000000 00 e0 1e a7 05 6f 00 10 ........
000008 5a a0 b9 12 08 00 46 00 ........
000010 03 68 00 00 00 00 0a 2e ........
202
000018 ee 33 0f 19 08 7f 0f 19 ........
000020 03 80 94 04 00 00 10 01 ........
000028 16 a2 0a 00 03 50 00 0c ........
000030 01 01 0f 19 03 80 11 01 ........
There is no limit on the width or number of bytes per line. Also the text dump at the end of the line is
ignored. Bytes/hex numbers can be uppercase or lowercase. Any text before the offset is ignored, including
email forwarding characters '>'. Any lines of text between the bytestring lines is ignored. The offsets are
used to track the bytes, so offsets must be correct. Any line which has only bytes without a leading offset
is ignored. An offset is recognized as being a hex number longer than two characters. Any text after the
bytes is ignored (e.g. the character dump). Any hex numbers in this text are also ignored. An offset of
zero is indicative of starting a new packet, so a single text file with a series of hexdumps can be converted
into a packet capture with multiple packets. Multiple packets are read in with timestamps differing by one
second each. In general, short of these restrictions, text2pcap is pretty liberal about reading in hexdumps
and has been tested with a variety of mangled outputs (including being forwarded through email multiple
times, with limited line wrap etc.)
There are a couple of other special features to note. Any line where the first non-whitespace character is
'#' will be ignored as a comment. Any line beginning with #TEXT2PCAP is a directive and options can be
inserted after this command to be processed by text2pcap. Currently there are no directives implemented;
in the future, these may be used to give more fine grained control on the dump and the way it should be
processed e.g. timestamps, encapsulation type etc.
Text2pcap also allows the user to read in dumps of application-level data, by inserting dummy L2, L3
and L4 headers before each packet. Possiblities include inserting headers such as Ethernet, Ethernet + IP,
Ethernet + IP + UDP, or Ethernet + Ip + TCP before each packet. This allows Wireshark or any other full-
packet decoder to handle these dumps.
203
Example D.8. Help information available for text2pcap
$ text2pcap -h
Text2pcap 1.1.4
Generate a capture file from an ASCII hexdump of packets.
Usage: text2pcap [options] <infile> <outfile>
where <infile> specifies input filename (use - for standard input)

<outfile> specifies output filename (use - for standard output)
Input:
-o hex|oct|dec parse offsets as (h)ex, (o)ctal or (d)ecimal; default is hex.
-t <timefmt> treats the text before the packet as a date/time code;
the specified argument is a format string of the sort
supported by strptime.
Example: The time "10:15:14.5476" has the format code
"%H:%M:%S."
NOTE: The subsecond component delimiter must be given
(.) but no pattern is required; the remaining number
is assumed to be fractions of a second.
NOTE: Date/time fields from the current date/time are
used as the default for unspecified fields.
Output:
-l <typenum> link-layer type number; default is 1 (Ethernet).
See the file net/bpf.h for list of numbers.
Use this option if your dump is a complete hex dump
of an encapsulated packet and you wish to specify
the exact type of encapsulation.
Example: -l 7 for ARCNet packets.
-m <max-packet> max packet length in output; default is 64000
Prepend dummy header:

-e <l3pid> prepend dummy Ethernet II header with specified L3PID
(in HEX).
Example: -e 0x806 to specify an ARP packet.
-i <proto> prepend dummy IP header with specified IP protocol
(in DECIMAL).
Automatically prepends Ethernet header as well.
Example: -i 46
-u <srcp>,<destp> prepend dummy UDP header with specified
dest and source ports (in DECIMAL).
Automatically prepends Ethernet & IP headers as well.
Example: -u 1000 69 to make the packets look like TFTP/UDP packets.
-T <srcp>,<destp> prepend dummy TCP header with specified
dest and source ports (in DECIMAL).
Example: -T 50,60
-s <srcp>,<dstp>,<tag> prepend dummy SCTP header with specified
dest/source ports and verification tag (in DECIMAL).
Example: -s 30,40,34
-S <srcp>,<dstp>,<ppi> prepend dummy SCTP header with specified
dest/source ports and verification tag 0.
Automatically prepends a dummy SCTP DATA
chunk header with payload protocol identifier ppi.
Example: -S 30,40,34
Miscellaneous:
-d detailed debug of parser states.
-q generate no output at all (automatically turns off -d).
204
D.9. idl2wrs: Creating dissectors from CORBA

IDL files
In an ideal world idl2wrs would be mentioned in the users guide in passing and documented in the
developers guide. As the developers guide has not yet been completed it will be documented here.
D.9.1. What is it?

As you have probably guessed from the name, idl2wrs takes a user specified IDL file and attempts to
build a dissector that can decode the IDL traffic over GIOP. The resulting file is "C" code, that should
compile okay as a Wireshark dissector.
idl2wrs basically parses the data struct given to it by the omniidl compiler, and using the GIOP API
available in packet-giop.[ch], generates get_CDR_xxx calls to decode the CORBA traffic on the wire.
It consists of 4 main files.
README.idl2wrs This document
wireshark_be.py The main compiler backend
wireshark_gen.py A helper class, that generates the C code.
idl2wrs A simple shell script wrapper that the end user should use to generate the
dissector from the IDL file(s).
D.9.2. Why do this?

It is important to understand what CORBA traffic looks like over GIOP/IIOP, and to help build a tool
that can assist in troubleshooting CORBA interworking. This was especially the case after seeing a lot of
discussions about how particular IDL types are represented inside an octet stream.
I have also had comments/feedback that this tool would be good for say a CORBA class when teaching
students what CORBA traffic looks like "on the wire".
It is also COOL to work on a great Open Source project such as the case with "Wireshark" ( http://
www.wireshark.org )
D.9.3. How to use idl2wrs

To use the idl2wrs to generate Wireshark dissectors, you need the following:
Prerequisites to using idl2wrs

1. Python must be installed. See http://python.org/
2. omniidl from the the omniORB package must be available. See http://omniorb.sourceforge.net/
3. Of course you need Wireshark installed to compile the code and tweak it if required. idl2wrs is part
of the standard Wireshark distribution
To use idl2wrs to generate an Wireshark dissector from an idl file use the following procedure:
205
Procedure for converting a CORBA idl file into a Wireshark dissector

1. To write the C code to stdout.
idl2wrs <your file.idl>
e.g.:
idl2wrs echo.idl
2. To write to a file, just redirect the output.

idl2wrs echo.idl > packet-test-idl.c
You may wish to comment out the register_giop_user_module() code and that will leave you with
heuristic dissection.
If you don't want to use the shell script wrapper, then try steps 3 or 4 instead.
3. To write the C code to stdout.

Usage: omniidl -p ./ -b wireshark_be <your file.idl>
e.g.:
omniidl -p ./ -b wireshark_be echo.idl
4. To write to a file, just redirect the output.

omniidl -p ./ -b wireshark_be echo.idl > packet-test-idl.c
You may wish to comment out the register_giop_user_module() code and that will leave you with
heuristic dissection.
5. Copy the resulting C code to subdirectory epan/dissectors/ inside your Wireshark source directory.
cp packet-test-idl.c /dir/where/wireshark/lives/epan/dissectors/
The new dissector has to be added to Makefile.common in the same directory. Look for the declaration
CLEAN_DISSECTOR_SRC and add the new dissector there. For example,
CLEAN_DISSECTOR_SRC = \
packet-2dparityfec.c \
packet-3com-njack.c \
...
becomes
CLEAN_DISSECTOR_SRC = \
packet-test-idl.c \
packet-2dparityfec.c \
packet-3com-njack.c \
...
For the next steps, go up to the top of your Wireshark source directory.
6. Run configure
./configure (or ./autogen.sh)
7. Compile the code
206
make
8. Good Luck !!
D.9.4. TODO
1. Exception code not generated (yet), but can be added manually.
2. Enums not converted to symbolic values (yet), but can be added manually.
3. Add command line options etc
4. More I am sure :-)
D.9.5. Limitations
See the TODO list inside packet-giop.c
D.9.6. Notes
1. The "-p ./" option passed to omniidl indicates that the wireshark_be.py and wireshark_gen.py are
residing in the current directory. This may need tweaking if you place these files somewhere else.
2. If it complains about being unable to find some modules (e.g. tempfile.py), you may want to check
if PYTHONPATH is set correctly. On my Linux box, it is PYTHONPATH=/usr/lib/python2.4/
207
Appendix E. This Document's License
(GPL)
As with the original licence and documentation distributed with Wireshark, this document is covered by
the GNU General Public Licence (GNU GPL).
If you haven't read the GPL before, please do so. It explains all the things that you are allowed to do with
this code and documentation.
GNU GENERAL PUBLIC LICENSE

Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.

59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies
of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your
freedom to share and change it. By contrast, the GNU General Public
License is intended to guarantee your freedom to share and change free
software--to make sure the software is free for all its users. This
General Public License applies to most of the Free Software
Foundation's software and to any other program whose authors commit to
using it. (Some other Free Software Foundation software is covered by
the GNU Library General Public License instead.) You can apply it to
your programs, too.
When we speak of free software, we are referring to freedom, not

price. Our General Public Licenses are designed to make sure that you
have the freedom to distribute copies of free software (and charge for
this service if you wish), that you receive source code or can get it
if you want it, that you can change the software or use pieces of it
in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid

anyone to deny you these rights or to ask you to surrender the rights.
These restrictions translate to certain responsibilities for you if you
distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether

gratis or for a fee, you must give the recipients all the rights that
you have. You must make sure that they, too, receive or can get the
source code. And you must show them these terms so they know their
rights.
We protect your rights with two steps: (1) copyright the software, and
(2) offer you this license which gives you legal permission to copy,
distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain
that everyone understands that there is no warranty for this free
software. If the software is modified by someone else and passed on, we
want its recipients to know that what they have is not the original, so
that any problems introduced by others will not reflect on the original
authors' reputations.
Finally, any free program is threatened constantly by software

patents. We wish to avoid the danger that redistributors of a free
208
This Document's License (GPL)
program will individually obtain patent licenses, in effect making the

program proprietary. To prevent this, we have made it clear that any
patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and

modification follow.
GNU GENERAL PUBLIC LICENSE

TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains

a notice placed by the copyright holder saying it may be distributed
under the terms of this General Public License. The "Program", below,
refers to any such program or work, and a "work based on the Program"
means either the Program or any derivative work under copyright law:
that is to say, a work containing the Program or a portion of it,
either verbatim or with modifications and/or translated into another
language. (Hereinafter, translation is included without limitation in
the term "modification".) Each licensee is addressed as "you".
Activities other than copying, distribution and modification are not

covered by this License; they are outside its scope. The act of
running the Program is not restricted, and the output from the Program
is covered only if its contents constitute a work based on the
Program (independent of having been made by running the Program).
Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's

source code as you receive it, in any medium, provided that you
conspicuously and appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact all the
notices that refer to this License and to the absence of any warranty;
and give any other recipients of the Program a copy of this License
along with the Program.
You may charge a fee for the physical act of transferring a copy, and
you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion
of it, thus forming a work based on the Program, and copy and
distribute such modifications or work under the terms of Section 1
above, provided that you also meet all of these conditions:
a) You must cause the modified files to carry prominent notices

stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in
whole or in part contains or is derived from the Program or any
part thereof, to be licensed as a whole at no charge to all third
parties under the terms of this License.
c) If the modified program normally reads commands interactively

when run, you must cause it, when started running for such
interactive use in the most ordinary way, to print or display an
announcement including an appropriate copyright notice and a
notice that there is no warranty (or else, saying that you provide
a warranty) and that users may redistribute the program under
these conditions, and telling the user how to view a copy of this
License. (Exception: if the Program itself is interactive but
does not normally print such an announcement, your work based on
the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If

identifiable sections of that work are not derived from the Program,
and can be reasonably considered independent and separate works in
themselves, then this License, and its terms, do not apply to those
sections when you distribute them as separate works. But when you
209
distribute the same sections as part of a whole which is a work based

on the Program, the distribution of the whole must be on the terms of
this License, whose permissions for other licensees extend to the
entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest

your rights to work written entirely by you; rather, the intent is to
exercise the right to control the distribution of derivative or
collective works based on the Program.
In addition, mere aggregation of another work not based on the Program

with the Program (or with a work based on the Program) on a volume of
a storage or distribution medium does not bring the other work under
the scope of this License.
3. You may copy and distribute the Program (or a work based on it,
under Section 2) in object code or executable form under the terms of
Sections 1 and 2 above provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable

source code, which must be distributed under the terms of Sections
1 and 2 above on a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three

years, to give any third party, for a charge no more than your
cost of physically performing source distribution, a complete
machine-readable copy of the corresponding source code, to be
distributed under the terms of Sections 1 and 2 above on a medium
customarily used for software interchange; or,
c) Accompany it with the information you received as to the offer

to distribute corresponding source code. (This alternative is
allowed only for noncommercial distribution and only if you
received the program in object code or executable form with such
an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for
making modifications to it. For an executable work, complete source
code means all the source code for all modules it contains, plus any
associated interface definition files, plus the scripts used to
control compilation and installation of the executable. However, as a
special exception, the source code distributed need not include
anything that is normally distributed (in either source or binary
form) with the major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless that component
itself accompanies the executable.
If distribution of executable or object code is made by offering

access to copy from a designated place, then offering equivalent
access to copy the source code from the same place counts as
distribution of the source code, even though third parties are not
compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program

except as expressly provided under this License. Any attempt
otherwise to copy, modify, sublicense or distribute the Program is
void, and will automatically terminate your rights under this License.
However, parties who have received copies, or rights, from you under
this License will not have their licenses terminated so long as such
parties remain in full compliance.
5. You are not required to accept this License, since you have not
signed it. However, nothing else grants you permission to modify or
distribute the Program or its derivative works. These actions are
prohibited by law if you do not accept this License. Therefore, by
modifying or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License to do so, and
210
all its terms and conditions for copying, distributing or modifying

the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the
Program), the recipient automatically receives a license from the
original licensor to copy, distribute or modify the Program subject to
these terms and conditions. You may not impose any further
restrictions on the recipients' exercise of the rights granted herein.
You are not responsible for enforcing compliance by third parties to
this License.
7. If, as a consequence of a court judgment or allegation of patent

infringement or for any other reason (not limited to patent issues),
conditions are imposed on you (whether by court order, agreement or
otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot
distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you
may not distribute the Program at all. For example, if a patent
license would not permit royalty-free redistribution of the Program by
all those who receive copies directly or indirectly through you, then
the only way you could satisfy both it and this License would be to
refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under

any particular circumstance, the balance of the section is intended to
apply and the section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to infringe any

patents or other property right claims or to contest validity of any
such claims; this section has the sole purpose of protecting the
integrity of the free software distribution system, which is
implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed
through that system in reliance on consistent application of that
system; it is up to the author/donor to decide if he or she is willing
to distribute software through any other system and a licensee cannot
impose that choice.
This section is intended to make thoroughly clear what is believed to

be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in

certain countries either by patents or by copyrighted interfaces, the
original copyright holder who places the Program under this License
may add an explicit geographical distribution limitation excluding
those countries, so that distribution is permitted only in or among
countries not thus excluded. In such case, this License incorporates
the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions
of the General Public License from time to time. Such new versions will
be similar in spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number. If the Program

specifies a version number of this License which applies to it and "any
later version", you have the option of following the terms and conditions
either of that version or of any later version published by the Free
Software Foundation. If the Program does not specify a version number of
this License, you may choose any version ever published by the Free Software
Foundation.
10. If you wish to incorporate parts of the Program into other free
programs whose distribution conditions are different, write to the author
to ask for permission. For software which is copyrighted by the Free
211
Software Foundation, write to the Free Software Foundation; we sometimes

make exceptions for this. Our decision will be guided by the two goals
of preserving the free status of all derivatives of our free software and
of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY

FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN
OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES
PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS
TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING

WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING
OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED
TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest

possible use to the public, the best way to achieve this is to make it
free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest

to attach them to the start of each source file to most effectively
convey the exclusion of warranty; and each file should have at least
the "copyright" line and a pointer to where the full notice is found.
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify

it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,

but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this

when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author

Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
This is free software, and you are welcome to redistribute it
under certain conditions; type `show c' for details.
212
The hypothetical commands `show w' and `show c' should show the appropriate
parts of the General Public License. Of course, the commands you use may
be called something other than `show w' and `show c'; they could even be
mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your
school, if any, to sign a "copyright disclaimer" for the program, if
necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program

`Gnomovision' (which makes passes at compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989

Ty Coon, President of Vice
This General Public License does not permit incorporating your program into
proprietary programs. If your program is a subroutine library, you may
consider it more useful to permit linking proprietary applications with the
library. If this is what you want to do, use the GNU Library General
Public License instead of this License.
213

WireShark Complete Users Guide

Uploaded by

Copyright:

Available Formats

WireShark Complete Users Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

WireShark Complete Users Guide

Uploaded by

Copyright:

Available Formats

Wireshark User's Guide

31944 for Wireshark 1.2

3. User Interface ............................................................................................................... 18

5.4. Merging capture files .......................................................................................... 69

7.3.4. "Expert" Packet List Column (optional) ...................................................... 103

10.6. Configuration Profiles ...................................................................................... 139

D.8. text2pcap: Converting ASCII hexdumps to network captures ................................... 202

2. Who should read this document?

• Martin Regner, for his various suggestions and corrections.

• Graeme Hewson, for a lot of grammatical corrections.

4. About this document

You will find some specially marked parts in this book:

5. Where to get the latest copy of this

6. Providing feedback about this document

1.1.1. Some intended purposes

• network administrators use it to troubleshoot network problems

• network security engineers use it to examine security problems

• developers use it to debug protocol implementations

• people use it to learn network protocol internals

• Available for UNIX and Windows.

• Capture live packet data from a network interface.

• Display packets with very detailed protocol information.

• Open and Save packet data captured.

• Filter packets on many criteria.

• Search for packets on many criteria.

• Colorize packet display based on filters.

• Create various statistics.

• ... and a lot more!

1.1.3. Live capture from many different network media

1.1.4. Import files from many other capture programs

1.1.5. Export files for many other capture programs

1.1.6. Many protocol decoders

1.1.7. Open Source Software

1.1.8. What Wireshark is not

1.2. System Requirements

1.2.1. General Remarks

• If Wireshark is running out of memory it crashes, see: http://wiki.wireshark.org/KnownBugs/

1.2.2. Microsoft Windows

• Any modern 32-bit x86 or 64-bit AMD64/x86-64 processor.

• 128MB available RAM. Larger capture files require more RAM.

• A supported network card for capturing:

• Other media: See http://wiki.wireshark.org/CaptureSetup/NetworkMedia

1.2.3. Unix / Linux

Binary packages are available for at least the following platforms:

• Red Hat Fedora/Enterprise Linux

1.3. Where to get Wireshark?

1.4. A brief history of Wireshark

1.5. Development and maintenance of

1.6. Reporting problems and getting help

Read the FAQ!

An online version is available at the Wireshark website: http://www.wireshark.org/faq.html. You might

1.6.4. Mailing Lists

1.6.5. Reporting Problems

2. Information about the platform you run Wireshark on.

3. A detailed description of your problem.

Don't send large files!

Don't send confidential information!

1.6.6. Reporting Crashes on UNIX/Linux platforms

You should mail the traceback to the wireshark-dev[AT]wireshark.org mailing list.

1.6.7. Reporting Crashes on Windows platforms