DVC6200f Instruction Manual

Instruction Manual
DVC6200f Digital Valve Controller
D103412X012
Fisherr FIELDVUE DVC6200f Digital Valve

Controller for FOUNDATION fieldbus
This manual applies to:

Device Type
4602
Device Revision
2
Hardware Revision 8
Firmware Revision 2.0
DD Revision
2 and 3
Instrument Level
FD, PD, AD
www.Fisher.com
August 2012
The FIELDVUE DVC6200f Digital Valve Controller is a core component of the PlantWeb digital
plant architecture. The digital valve controller powers PlantWeb by capturing and delivering valve
diagnostic data. Coupled with ValveLink software, the DVC6200 provides users with an accurate
picture of valve performance, including actual stem position, instrument input signal, and
pneumatic pressure to the actuator. Using this information, the digital valve controller diagnoses
not only itself, but also the valve and actuator to which it is mounted.
Instruction Manual
D103412X012
August 2012
Contents
Section 1 Introduction and
Specifications . . . . . . . . . . . . . . . . . . . . . . 3
Figure 11. FIELDVUE DVC6200f Digital Valve

Controller
Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Instrument Description . . . . . . . . . . . . . . . . . . . . . . . . 3
Using this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Related Information . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Educational Services . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Section 2 Installation . . . . . . . . . . . . . . . . . 11
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DVC6200f Digital Valve Controller . . . . . . . . . . . . .
DVC6205f Base Unit . . . . . . . . . . . . . . . . . . . . . . . .
DVC6215 Feedback Unit . . . . . . . . . . . . . . . . . . . . .
SlidingStem Linear Actuators up to
210 mm (8.25 Inches) Travel . . . . . . . . . . .
Fisher Rotary Actuators and SlidingStem
Linear Actuators over 210 mm
(8.25 Inches) Travel . . . . . . . . . . . . . . . . . . .
GX Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . .
QuarterTurn Rotary Actuators . . . . . . . . . . . .
Fisher 67CFR Filter Regulator . . . . . . . . . . . . . . . . .
Pneumatic Connections . . . . . . . . . . . . . . . . . . . . . . .
Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Connection . . . . . . . . . . . . . . . . . . . . . .
Special Construction to Support
Solenoid Valve Testing . . . . . . . . . . . . . . . .
Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring and Electrical Connections . . . . . . . . . . . . . .
Connecting Fieldbus Wiring . . . . . . . . . . . . . . . . . .
TwistedShielded Pair . . . . . . . . . . . . . . . . . . . .
Quick Connect Cable Entry . . . . . . . . . . . . . . .
Remote Travel Sensor Connections . . . . . . . . . . . .
Communication Connections . . . . . . . . . . . . . . . . .
Simulate Enable Jumper . . . . . . . . . . . . . . . . . . . . . . .
Commissioning Tag . . . . . . . . . . . . . . . . . . . . . . . . . .
11
11
11
14
16
18
20
22
25
26
26
26
27
28
29
30
31
31
32
33
34
36
36
27
Section 3 Basic Setup . . . . . . . . . . . . . . . . . 39
W9713_fieldbus
Input Selector Function Block . . . . . . . . . . . . . . . . .

Output Splitter Function Block . . . . . . . . . . . . . . . .
Analog Input Function Block . . . . . . . . . . . . . . . . . .
Mulitple Analog Input Function Block . . . . . . . . . .
Discrete Output Function Block . . . . . . . . . . . . . . .
Discrete Input Function Block . . . . . . . . . . . . . . . . .
145
160
171
183
189
201
Section 5 Calibration . . . . . . . . . . . . . . . . 213

Calibration Overview . . . . . . . . . . . . . . . . . . . . . . . .
Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply Pressure Sensor . . . . . . . . . . . . . . . . . . . . .
Pressure A or B Sensor . . . . . . . . . . . . . . . . . . . . . .
213
213
214
214
215
216
217
Section 6 Viewing Device

Variables and Diagnostics . . . . . . . . . . 219
Section 4 Detailed Setup . . . . . . . . . . . . . . 45
View Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resource Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . .
Device Variables . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transducer Block . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . .
Device Variables . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resource Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Transducer Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Analog Output Function Block . . . . . . . . . . . . . . . . 113
Proportional/Integral/Derivative
Function Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Replacing the Magnetic Feedback Assembly . . . . . 234

Module Base Maintenance . . . . . . . . . . . . . . . . . . . . 234
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transducer Block Mode . . . . . . . . . . . . . . . . . . . . . .
Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performance Tuner . . . . . . . . . . . . . . . . . . . . . . . . .
39
39
39
40
44
219
219
220
222
223
224
229
Section 7 Maintenance and

Troubleshooting . . . . . . . . . . . . . . . . . . 233
Instruction Manual

August 2012
Component Replacement . . . . . . . . . . . . . . . . . . .
Removing the Module Base . . . . . . . . . . . . . . . . .
Replacing the Module Base . . . . . . . . . . . . . . . . . .
Submodule Maintenance . . . . . . . . . . . . . . . . . . . . .
I/P Converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printed Wiring Board (PWB) Assembly . . . . . . . . .
Pneumatic Relay . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gauges, Pipe Plugs or Tire Valves . . . . . . . . . . . . .
Terminal Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removing the Terminal Box . . . . . . . . . . . . . . . . .
Replacing the Terminal Box . . . . . . . . . . . . . . . . .
Stroking the Digital Valve Controller Output . . . . .
DVC6215 Feedback Unit . . . . . . . . . . . . . . . . . . . . .
Instrument Troubleshooting . . . . . . . . . . . . . . . . . .
D103412X012
235
235
236
237
237
239
240
241
241
241
242
242
242
243
Section 8 Parts . . . . . . . . . . . . . . . . . . . . . 249

Parts Ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Common Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/P Converter Assembly . . . . . . . . . . . . . . . . . . . . .
Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Terminal Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PWB Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pressure Gauges, Pipe Plugs, or
Tire Valve Assemblies . . . . . . . . . . . . . . . . . . . .
249
249
250
250
250
250
251
251
251
252
252
Appendix A Principle of Operation . . . . . 259

Digital Valve Controller Operation . . . . . . . . . . . . . 259
Appendix B Field Communicator

Menu Tree . . . . . . . . . . . . . . . . . . . . . . . 261
Appendix C PlantWeb Alerts . . . . . . . . . . 275
Alert Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PlantWeb Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alert Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alert Reporting . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PlantWeb Alerts Set Block Status . . . . . . . . . . . . .
Setting PlantWeb Alerts . . . . . . . . . . . . . . . . . . . . . .
Using PlantWeb Alerts . . . . . . . . . . . . . . . . . . . . . . .
275
275
275
277
277
277
277
Appendix D FOUNDATION Fieldbus

Communication . . . . . . . . . . . . . . . . . . 287
Function Block Overview . . . . . . . . . . . . . . . . . . . . . 287
Function Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
Instrument Specific Blocks . . . . . . . . . . . . . . . . . .

Resource Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transducer Blocks . . . . . . . . . . . . . . . . . . . . . . . . .
Block Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Explanation of Modes . . . . . . . . . . . . . . . . . . . . . .
Examples of Modes for Various
Operation Statuses . . . . . . . . . . . . . . . . . . . . . .
Device Descriptions . . . . . . . . . . . . . . . . . . . . . . . . .
Transducer Block Status and Limit Propagation . .
Status Propagation . . . . . . . . . . . . . . . . . . . . . . . .
Limit Propagation . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Communication . . . . . . . . . . . . . . . . . . . .
Device Addressing . . . . . . . . . . . . . . . . . . . . . . . . .
Link Active Scheduler . . . . . . . . . . . . . . . . . . . . . . .
Device Communications . . . . . . . . . . . . . . . . . . . .
Scheduled Transfers . . . . . . . . . . . . . . . . . . . .
Unscheduled Transfers . . . . . . . . . . . . . . . . . .
Function Block Scheduling . . . . . . . . . . . . . . . . . .
Network Management . . . . . . . . . . . . . . . . . . . . . . .
288
288
288
289
290
291
291
291
292
292
293
293
293
294
294
295
296
296
Appendix E Device Description

Installation . . . . . . . . . . . . . . . . . . . . . . 297
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Device Descriptions and Methods . . . . . . . . . . . . .
Installing DD on a DeltaV
ProfessionalPLUS Workstation . . . . . . . . . . . . . . . .
Installing DDs on Other Fieldbus Host Systems . . .
Displaying the Device Description Revision . . . . . .
297
298
298
300
301
Appendix F Operating with a

DeltaV System . . . . . . . . . . . . . . . . . . . 303
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transducer Block Parameter Configuration Index . . . . . . . . . . . . . . . . . . . . . . .
Resource Block Parameter - Configuration Index .
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Functionality/System Requirements . . .
Using AMS Device Manager . . . . . . . . . . . . . . . . . . .
Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing Parameters . . . . . . . . . . . . . . . . . . . . . . .
Bringing the Device OnLine . . . . . . . . . . . . . . . . . .
PlantWeb Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting up PlantWeb Alerts . . . . . . . . . . . . . . . . . .
303
304
309
310
310
310
312
312
315
315
315
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . 321
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
Instruction Manual
Introduction and Specifications
D103412X012
August 2012
Section 1 Introduction and Specifications

Scope of Manual
This instruction manual is a supplement to the DVC6200 Series Quick Start Guide (D103556X012) that ships with
every instrument. This instruction manual includes product specifications, installation information, reference
materials, custom setup information, maintenance procedures, and replacement part details for the FIELDVUE
DVC6200f digital valve controller.
Note
All references to the DVC6200f digital valve controller include the DVC6205f base unit unless otherwise indicated.
This manual describes device setup using the 475 or 375 Field Communicator. For information on using Fisher
ValveLink software with the instrument, refer to the appropriate user guide or help.
Do not install, operate, or maintain a DVC6200f digital valve controller without being fully trained and qualified in
valve, actuator, and accessory installation, operation, and maintenance. To avoid personal injury or property damage,
it is important to carefully read, understand, and follow all of the contents of this manual, including all safety cautions
and warnings. If you have any questions about these instructions, contact your Emerson Process Management sales
office before proceeding.
Instrument Description
DVC6200f digital valve controllers for FOUNDATION fieldbus are communicating, microprocessorbased instruments.
In addition to the traditional function of converting a digital signal to a pneumatic output pressure, the DVC6200f
digital valve controller, using FOUNDATION fieldbus communications protocol, gives easy access to information critical to
process operation as well as process control. This can be done using a DeltaV console, another FOUNDATION fieldbus
system console, or with ValveLink software version 10.2 or later.
Using a compatible fieldbus configuration device, you can obtain information about the health of the instrument, the
actuator, and the valve. You can also obtain asset information about the actuator or valve manufacturer, model, and
serial number. You can set input and output configuration parameters and calibrate the instrument.
Using the FOUNDATION fieldbus protocol, information from the instrument can be integrated into control systems.
DVC6200f digital valve controllers can be mounted on single or doubleacting slidingstem actuators, as shown in
figure 12, or on rotary actuators. It can also be integrally mounted to the Fisher GX control valve and actuator system,
as shown in figure 13. The DVC6200f mounts on most Fisher and other manufacturers' rotary and slidingstem
actuators.
Instruction Manual

August 2012
Figure 12 FIELDVUE DVC6200f Digital Valve

Controller Mounted on a Fisher SlidingStem Valve
Actuator
D103412X012
Figure 13. FIELDVUE DVC6200f Digital Valve

Controller Integrally Mounted to a Fisher GX Control
Valve and Actuator System
W9616_fieldbus
W9643_fieldbus
DVC6200f digital valve controllers are available with several selections of control and diagnostic capability. Control
selections include:
Standard Control (SC) Digital valve controllers with Standard Control have the AO, PID, ISEL, OS, AI, MAI, DO, and
four DI function blocks in addition to the resource and transducer blocks.
Fieldbus Control (FC)Digital valve controllers with Fieldbus Control have the AO function block in addition to the
resource and transducer blocks.
Fieldbus Logic (FL)Digital valve controllers with Fieldbus Logic have the DO, and four DI function blocks, in
addition to the resource and transducer block.
The diagnostic capabilities include:
Performance Diagnostics (PD)
Advanced Diagnostics (AD)
Fieldbus Diagnostics (FD)
Performance and Advanced Diagnostics are available with ValveLink software. They provide visibility to instrument
alerts. Fieldbus Diagnostics can be viewed with any host system.
Instruction Manual
D103412X012
August 2012
Instrument Blocks
The digital valve controller is a blockbased device. For detailed information on the blocks within the digital valve
controller, see the Detailed Setup section of this manual.
The DVC6200f digital valve controller includes the resource and transducer block:
Resource BlockThe resource block contains the hardware specific characteristics associated with a device; it has
no input or output parameters. The resource block monitors and controls the general operation of other blocks
within the device. For example, when the mode of the resource block is Out of Service, it impacts all function
blocks.
Transducer BlockThe transducer block connects the analog output function block to the I/P converter, relay, and
travel sensor hardware within the digital valve controller.
Function Blocks
In addition to the resource and transducer block, the digital valve controller may contain the following function blocks.
For additional information on function blocks, refer to Appendix D, FOUNDATION fieldbus Communication.
Analog Output (AO) Function BlockThe analog output function block accepts the output from another function
block (such as a PID block) and transfers it as an actuator control signal to the transducer block. If the DO block is
selected, the AO block is not functional.
ProportionalIntegralDerivative (PID) Function BlockThe PID function block performs
proportionalplusintegralplusderivative control.
Input Selector (ISEL) Function BlockThe input selector function block selects from up to four inputs and may
provide the selected signal as input to the PID block. The input selection can be configured to select the first good
input signal; a maximum, minimum or average value; or a hot spare.
Output Splitter (OS) Function BlockThe output splitter function block accepts the output from another function
block (such as a PID block) and creates two outputs that are scaled or split, according to the user configuration. This
block is typically used for split ranging of two control valves.
Analog Input (AI) Function BlockThe analog input function block monitors the signal from a DVC6200f sensor or
internal measurement and provides it to another block.
Multiple Analog Input (MAI) Function BlockThe Multiple Analog Input (MAI) function block has the ability to
process up to eight DVC6200f measurements and make them available to other function blocks.
Discrete Output (DO) Function BlockThe discrete output function block processes a discrete set point and sends it
to a specified output channel, which can be transferred to the transducer block for actuator control. In the digital
valve controller, the discrete output block provides both normal open/closed control and the ability to position the
valve in 5% increments for course throttling applications. If the AO block is selected, the DO block is not functional.
Discrete Input (DI) Function BlockThe discrete input function block processes a single discrete input from a
DVC6200f and makes it available to other function blocks. In the digital valve controller, the discrete input function
block can provide limit switch functionality and valve position proximity detection.

August 2012
Instruction Manual
D103412X012
Using This Manual

Navigation paths and fastkey sequences are included for procedures and parameters that can be accessed using the
Field Communicator.
For example, to access Resource Block Mode:
Field Communicator
RB > Configure/Setup > Setup > Resource Block Mode
An overview of the resource and transducer block menu structures are shown in Appendix B. Menu structures for the
function blocks are included with each function block section in Detailed Setup.
Throughout this document, parameters are typically referred to by their common name or label, followed by the
parameter name and index number; for example, Write Priority (WRITE_PRI [39]). However, not all interface systems
support the use of the parameter label and instead use only the Parameter Name, followed by the index number, when
referring to the block parameters.
Specifications
Specifications for the DVC6200f digital valve controller are shown in table 11.
Instruction Manual
D103412X012
August 2012
Table 11. Specifications

Available Mounting
DVC6200f digital valve controller and DVC6215
feedback unit: Integral mounting to the Fisher GX
Control Valve and Actuator System Integral
mounting to Fisher rotary actuators, Slidingstem
linear applications Quarterturn rotary applications
DVC6205f base unit for 2 inch pipestand or wall
mounting (for remote-mount)
The DVC6200f digital valve controller or DVC6215
feedback unit can also be mounted on other
actuators that comply with IEC 60534-6-1, IEC
60534-6-2, VDI/VDE 3845 and NAMUR mounting
standards.
Function Block Suites
Standard Control (throttling control)
Includes AO, PID, ISEL, OS, AI, MAI, DO,
and four DI function block
Fieldbus Control (throttling control)
Contains the AO function block
Fieldbus Logic [discrete (on/off) connectivity]
Includes DO, and four DI function blocks
Block Execution Times
AO Block: 15 ms
PID Block: 20 ms
ISEL Block: 20 ms
OS Block: 20 ms
AI Block: 15 ms
MAI BLock: 35 ms
DO Block: 15 ms
DI Block: 15 ms
Electrical Input
Voltage Level: 9 to 32 volts
Maximum Current: 19 mA
Reverse Polarity Protection: Unit is not polarity
sensitive
Termination: Bus must be properly terminated per
ISA SP50 guidelines
Digital Communication Protocol
FOUNDATION fieldbus registered device
Physical Layer Type(s):
121Low-power signaling, buspowered,
Entity Model I.S.
511Low-power signaling, buspowered, FISCO I.S.
Fieldbus Device Capabilities

Backup Link Master capable
Supply Pressure(1)
Minimum Recommended: 0.3 bar (5 psig) higher
than maximum actuator requirements
Maximum: 10.0 bar (145 psig) or maximum pressure
rating of the actuator, whichever is lower
Supply Medium
Air or natural gas
Air: Supply pressure must be clean, dry air that meets
the requirements of ISA Standard 7.0.01. A maximum
40 micrometer particle size in the air system is
acceptable. Further filtration down to 5 micrometer
particle size is recommended. Lubricant content is
not to exceed 1 ppm weight (w/w) or volume (v/v)
basis. Condensation in the air supply should be
minimized.
Natural Gas: Natural gas must be clean, dry, oilfree,
and noncorrosive. H2S content should not exceed 20
ppm.
Output Signal
Pneumatic signal, up to 95% of supply pressure
Minimum Span: 0.4 bar (6 psig)
Maximum Span: 9.5 bar (140 psig)
Action: Double, Single Direct or Reverse
Steady-State Air Consumption(2)(3)
Standard Relay: At 1.4 bar (20 psig) supply pressure:
Less than 0.38 normal m3/hr (14 scfh)
At 5.5 bar (80 psig) supply pressure: Less than 1.3
normal m3/hr (49 scfh)
Low Bleed Relay: At 1.4 bar (20 psig) supply pressure:
Average value 0.056 normal m3/hr
(2.1 scfh)
At 5.5 bar (80 psig) supply pressure: Average value
0.184 normal m3/hr (6.9 scfh)
Maximum Output Capacity(2)(3)
At 1.4 bar (20 psig) supply pressure: 10.0 normal m3/hr
(375 scfh)
At 5.5 bar (80 psig) supply pressure: 29.5 normal m3/hr
(1100 scfh)
-continued-
Instruction Manual

August 2012
D103412X012
Table 11. Specifications (continued)

Operating Ambient Temperature Limits(1)(4)
-40 to 85C (-40 to 185F)
-52 to 85C (-62 to 185F) for instruments utilizing
the Extreme Temperature option (fluorosilicone
elastomers)
-52 to 125C (-62 to 257F) for remotemount
feedback unit
Electrical Housing
CSA Type 4X, IP66
FM NEMA 4X
ATEX IP66
IECEx IP66
The Gas Certified DVC6200f is CSA, FM, ATEX, and
IECEx approved for use with natural gas as the supply
medium
Independent Linearity(5)
Typical Value: 0.50% of output span
Electromagnetic Compatibility
Meets EN 61326-1 (First Edition)
ImmunityIndustrial locations per Table 2 of
the EN 61326-1 standard. Performance is
shown in table 12 below.
EmissionsClass A
ISM equipment rating: Group 1, Class A
Lightning and Surge ProtectionThe degree of
immunity to lightning is specified as Surge immunity
in table 12. For additional surge protection
commercially available transient protection devices
can be used.
Vibration Testing Method
Tested per ANSI/ISA75.13.01 Section 5.3.5. A
resonant frequency search is performed on all three
axes. The instrument is subjected to the ISA specified
1/2 hour endurance test at each major resonance.
Other Classifications/Certifications
INMETRO Brazil
KGS Korea
NEPSI China
TIIS Japan
Contact your Emerson Process Management sales
office for classification/certification specific
information
Connections
Supply Pressure: 1/4 NPT internal and integral pad for
mounting 67CFR regulator
Output Pressure: 1/4 NPT internal
Tubing: 3/8inch recommended
Vent: 3/8 NPT internal
Electrical: 1/2 NPT internal, M20 adapter optional
Actuator Compatibility
Humidity Testing Method

Tested per IEC 61514-2
Electrical Classification
Hazardous Area Approvals
CSA Intrinsically Safe and FISCO, Explosionproof,
Division 2, Dust Ignitionproof
FM Intrinsically Safe and FISCO, Explosionproof,
NonIncendive, Dust Ignitionproof
ATEXIntrinsically Safe, FISCO and Dust,
Flameproof and Dust, Type n and Dust
IECEx Intrinsically Safe and FISCO, Flameproof,
Type n
Stem Travel (SlidingStem Linear)

Minimum: 6.35 mm (0.25 inch)
Maximum: 606 mm (237/8 inches)
Shaft Rotation (QuarterTurn Rotary)
Minimum: 45
Maximum: 90
Weight
DVC6200f
Aluminum: 3.5 kg (7.7 lbs)
Stainless Steel: 8.6 kg (19 lbs)
DVC6205f: 4.1 kg (9 lbs)
DVC6215: 1.4 kg (3.1 lbs)
-continued-
Instruction Manual
D103412X012
August 2012
Table 11. Specifications (continued)

Contact your Emerson Process Management sales
office or go to www.FIELDVUE.com for additional
information.
Construction Materials
Housing, module base and terminal box: A03600 low
copper aluminum alloy (standard)
Stainless steel (optional)
Cover: Thermoplastic polyester
Elastomers: Nitrile (standard)
Fluorosilicone (extreme temperature)
Declaration of SEP
Fisher Controls International LLC declares this
product to be in compliance with Article 3 paragraph
3 of the Pressure Equipment Directive (PED) 97 / 23 /
EC. It was designed and manufactured in accordance
with Sound Engineering Practice (SEP) and cannot
bear the CE marking related to PED compliance.
However, the product may bear the CE marking to
indicate compliance with other applicable European
Community Directives.
Options
Supply and output pressure gauges or Tire
valves Integral mounted filter regulator
LowBleed Relay Extreme Temperature
Natural Gas Certified Remote Mount
Stainless Steel
NOTE: Specialized instrument terms are defined in ANSI/ISA Standard 51.1 - Process Instrument Terminology.
1. The pressure/temperature limits in this document and any other applicable code or standard should not be exceeded.
2. Normal m3/hour - Normal cubic meters per hour at 0C and 1.01325 bar, absolute. Scfh - Standard cubic feet per hour at 60F and 14.7 psia.
3. Values at 1.4 bar (20 psig) based on a single-acting direct relay; values at 5.5 bar (80 psig) based on double-acting relay.
4. Temperature limits vary based on hazardous area approval.
5. Not applicable for travels less than 19 mm (0.75 inch) or for shaft rotation less than 60 degrees. Also not applicable for digital valve controllers in long-stroke applications.
Table 12. EMC Summary ResultsImmunity

Port
Enclosure
Basic Standard
Electrostatic discharge (ESD)
IEC 6100042
4 kV contact
8 kV air
Radiated EM field
IEC 6100043
80 to 1000 MHz @ 10V/m with 1 kHz AM at 80%

IEC 6100048
30 A/m at 50/60 Hz
Rated power frequency

magnetic field
Burst
I/O signal/control
Test Level
Performance
Criteria(1)
Phenomenon
A(2)
A(2)
IEC 6100044
1 kV
Surge
IEC 6100045
1 kV
Conducted RF
IEC 6100046
150 kHz to 80 MHz at 3 Vrms
Performance criteria: +/- 1% effect.

1. A = No degradation during testing. B = Temporary degradation during testing, but is selfrecovering.
2. Excluding Simulate function, which meets Performance Criteria B.
Instruction Manual
August 2012
D103412X012
Related Information
Fieldbus Installation and Wiring Guidelines
This manual describes how to connect the fieldbus to the digital valve controller. For a technical description, planning,
and installation information for a FOUNDATION fieldbus, refer to the FOUNDATION fieldbus Technical Overview available
from the Fieldbus Foundation and Fieldbus Installations in a DeltaV System available from your Emerson Process
Management sales office.
Related Documents
Other documents containing information related to the DVC6200f digital valve controller include:
Bulletin 62.1:DVC6200fFisher FIELDVUE DVC6200f Digital Valve Controller (D103399X012)
Bulletin 62.1:DVC6200f FDFisher FIELDVUE DVC6200f Digital Valve Controller (D103422X012)
Bulletin 62.1:DVC6200(S1)Fisher FIELDVUE DVC6200 Digital Valve Controller Dimensions (D103543X012)
Fisher FIELDVUE DVC6200 Series Quick Start Guide (D103556X012)
475 Field Communicator User's Manual
ValveLink Software Help or Documentation
All documents are available from your Emerson Process Management sales office. Also visit our website at
www.FIELDVUE.com.
Educational Services
For information on available courses for the DVC6200f digital valve controller, as well as a variety of other products,
contact:
Emerson Process Management
Educational Services, Registration
P.O. Box 190; 301 S. 1st Ave.
Marshalltown, IA 50158-2823
Phone: 800-338-8158 or
Phone: 641-754-3771
FAX: 641-754-3431
email: education@emerson.com
10
Instruction Manual
Installation
D103412X012
August 2012
Section 2 Installation2-2Installation
WARNING
Avoid personal injury or property damage from sudden release of process pressure or bursting of parts. Before proceeding
with any Installation procedures:
Always wear protective clothing, gloves, and eyewear to prevent personal injury or property damage.
If installing into an existing application, also refer to the WARNINGS at the beginning of the Maintenance section of this
instruction manual.
Check with your process or safety engineer for any additional measures that must be taken to protect against process
media.
WARNING
To avoid static discharge from the plastic cover when flammable gases or dust are present, do not rub or clean the cover
with solvents. To do so could result in a spark that may cause the flammable gases or dust to explode, resulting in personal
injury or property damage. Clean with a mild detergent and water only.
Refer to the quick start guide that ships with the instrument (D103556X012) for Hazardous Area Approvals and Special
Instructions for Safe Use and Installations in Hazardous Locations.
Mounting
The DVC6200f housing is available in two different configurations, depending on the actuator mounting method.
Figure 21 shows the available configurations.
Figure 21. Housing Configurations
HOUSING FOR
LINEAR AND ROTARY ACTUATORS
HOUSING FOR
FISHER GX ACTUATORS
INTEGRAL OUTPUT
PRESSURE PORT
ROTARY NAMUR, M6
LINEAR, M8
W9703
W9704
SLOTS FOR
MOUNTING BOLTS
HOLE FOR
MOUNTING BOLT
11
Installation
Instruction Manual
August 2012
D103412X012
The feedback system for the DVC6200f digital valve controller utilizes a magnetic assembly for linkageless,
noncontacting position measurement. In order to prevent inadvertent stem movement while the instrument is in
operation, magnetic tools (such as a magnetictipped screwdriver) should not be used.
Note
The magnet assembly may be referred to as a magnetic array in user interface tools.
CAUTION
The magnet assembly material has been specifically chosen to provide a longterm stable magnetic field.
However, as with any magnet, care must be taken when handling the magnet assembly. Another high powered magnet
placed in close proximity (less than 25 mm) can cause permanent damage. Potential sources of damaging equipment
include, but are not limited to: transformers, DC motors, stacking magnet assemblies.
CAUTION
General Guidelines for use of High Power Magnets with Positioners
Use of high power magnets in close proximity to any positioner which is operating a process should be avoided. Regardless
of the positioner model, high power magnets can affect the positioners ability to control the valve. Technicians should
avoid the use of high power magnets in close proximity with any positioner.
Use of Magnetic Tools with the DVC6200f

Magnetic Tip Screw Drivers Magnetic tip screw drivers can be used to work on the DVC6200f. However, they should
not be brought in close proximity to the magnet Assembly (located at the back of the instrument) during process
operations.
Calibrator Strap Magnets These are high power magnets used to hold 4-20 ma calibrators.
Normally, these calibrators would not be used while an instrument is controlling the process.
High power magnets should be kept at least 15 cm (6 inches) from the DVC6200f.
Note
As a general rule, do not use less than 60% of the magnet assembly travel range for full travel measurement. Performance will
decrease as the assembly is increasingly subranged.
The linear magnet assemblies have a valid travel range indicated by arrows molded into the piece. This means that the hall sensor
(on the back of the DVC6200f housing) has to remain within this range throughout the entire valve travel. See figure 22. The
linear magnet assemblies are symmetrical. Either end may be up.
12
Instruction Manual
Installation
D103412X012
August 2012
Figure 22. Travel Range
VALID TRAVEL RANGE

50 mm (2 INCH) SHOWN
MAGNET ASSEMBLY
(ATTACHED TO VALVE STEM)
INDEX MARK
W9706
Note
Mounting the instrument vertically, with the vent at the bottom of the assembly, or horizontally, with the vent pointing down, is
recommended to allow drainage of moisture that may be introduced via the instrument air supply.
There are a variety of mounting brackets and kits that are used to mount the DVC6200f to different actuators.
Depending on the actuator, there will be differences in fasteners, brackets, and connecting linkages.
Each mounting kit will include one of the magnet assemblies illustrated in figure 23.
Figure 23. Magnet Assemblies
RSHAFT END
ASSEMBLY 90 DEG
AVAILABLE CONSTRUCTIONS:
SSTEM #7 ASSEMBLY (7 mm / 1/4 INCH)
SSTEM #25 ASSEMBLY (25 mm / 1 INCH)
SSTEM #210 ASSEMBLY (210 mm / 8-1/4 INCH)
SSTEM #1 ROLLER ASSEMBLY
RSHAFT #1 WINDOW ASSEMBLY
(FISHER 2052 SIZE 2 & 3, 1051/1052
SIZE 4070, 1061 SIZE 30100,
SLIDINGSTEM > 210 mm (8.25 INCHES)
RSHAFT #2 WINDOW ASSEMBLY
(2052 SIZE 1, 1051/1052 SIZE 20-33)
If ordered as part of a control valve assembly, the factory will mount the digital valve controller on the actuator and
calibrate the instrument. If purchased separately, you will need a mounting kit to mount the digital valve controller on
the actuator. Each mounting kit includes detailed information on mounting the digital valve controller to a specific
actuator. Refer to table 21 for the more common Fisher actuator mounting instructions, available at www.fisher.com
or your Emerson Process Management sales office.
13
Instruction Manual
Installation
August 2012
D103412X012
For general mounting guidelines, refer to the DVC6200 Series quick start guide (D103556X012), available at
www.fisher.com or your Emerson Process Management sales office.
Table 21. FIELDVUE DVC6200f Mounting Instructions

Instructions for Mounting:
Part Number
585C/585CR Size 25 Actuator with or without Handjack
D103439X012
585C/585CR Size 50 Actuator with or without Handjack
D103440X012
657 and 667 Size 30-60 Actuators
D103441X012
657 and 667 Size 34-60 Actuators with Handwheel
D103442X012
657 and 667 Size 70, 76, and 87 Actuators (up to 2 inch travel)
D103443X012
657 and 667 Size 70, 76, and 87 Actuators (4 inch travel)
D103444X012
657 and 667 Size 80 Actuators (up to 2 inch travel)
D103445X012
657 and 667 Size 80 Actuators (4 inch travel)
D103446X012
1051 Size 33 and 1052 Size 20 and 33 Actuators (Window Mount)
D103447X012
1051 and 1052 Size 33 Actuators (End Mount)
D103448X012
1051 and 1052 Size 40-70 Actuators (Window Mount)
D103449X012
1051 and 1052 Size 40-70 Actuators (End Mount)
D103450X012
1052 Size 20 Actuator (End Mount)
D103451X012
1061 Size 30-68 Actuator (Window Mount)
D103453X012
1061 Size 80-100 Actuator (Window Mount)
D103452X012
2052 Size 1, 2, 3 Actuator (End Mount)
D103454X012
2052 Size 1, 2, 3 Actuator with Spacer (Window Mount)
D103455X012
Baumann SlidingStem Actuators
D103456X012
GX Control Valve and Actuator System
D103457X012
IEC6053461 (NAMUR) Sliding-Stem Actuators
D103458X012
IEC6053462 (NAMUR) Rotary Actuators
D103459X012
DVC6205f Base Unit

For remotemounted digital valve controllers, the DVC6205f base unit ships separately from the control valve and
does not include tubing, fittings or wiring. See the instructions that come with the mounting kit for detailed
information on mounting the feedback unit to a specific actuator model.
Mount the DVC6205f base unit on a 50.8 mm (2 inch) pipestand or wall. The included bracket is used for either
mounting method.
Wall Mounting
Refer to figures 24 and 25. Drill two holes in the wall using the dimensions shown in figure 24. Attach the mounting
bracket to the base unit using four spacers and 25.4 mm (1inch) 1/420 hex head screws. Attach the base unit to the
wall using suitable screws or bolts.
Pipestand Mounting
Refer to figure 26. Position a standoff on the back of the base unit. Using two 101.6 mm (4inch) 1/420 hex head
screws loosely attach the base unit to the pipestand with the mounting bracket. Position the second standoff, then
using the remaining 101.6 mm (4inch) hex head screws, securely fasten the base unit to the pipe stand.
14
Instruction Manual
Installation
D103412X012
August 2012
Figure 24. FIELDVUE DVC6205f Base Unit with Mounting Bracket (Rear View)
10C1796A
Figure 25. FIELDVUE DVC6205f Base Unit Wall Mounting
4INCH 1/420
HEX HEAD SCREW
STANDOFF
MOUNTING BRACKET
X0437
15
Instruction Manual
Installation
August 2012
D103412X012
Figure 26. FIELDVUE DVC6205f Base Unit Pipestand Mounting
SPACER
1INCH 1/420
HEX HEAD
SCREW
MOUNTING BRACKET
X0428
DVC6215 Feedback Unit

If ordered as part of a control valve assembly, the factory mounts the feedback unit on the actuator, makes pneumatic
connections to the actuator, sets up, and calibrates the instrument. If you purchased the feedback unit separately, you
will need a mounting kit to mount the feedback unit on the actuator. See the instructions that come with the
mounting kit for detailed information on mounting the feedback unit to a specific actuator model.
The DVC6215 housing is available in two different configurations, depending on the actuator mounting method.
Figure 27 shows the available configurations. The feedback system for the DVC6215 feedback unit utilizes a magnetic
assembly for true linkageless, noncontacting position measurement. In order to prevent inadvertent stem
movement while the instrument is in operation, magnetic tools (such as a magnetictipped screwdriver) should not be
used.
Figure 27. Feedback Unit Housing Configurations
HOUSING FOR
LINEAR AND ROTARY ACTUATORS
HOUSING FOR
FISHER GX ACTUATORS
INTEGRAL OUTPUT
PRESSURE PORT
X0124
16
LINEAR, M8
ROTARY NAMUR, M6
X0125
HOLES FOR
MOUNTING BOLT
Instruction Manual
Installation
D103412X012
August 2012
CAUTION
The magnet assembly material has been specifically chosen to provide a longterm stable magnetic field.
However, as with any magnet, care must be taken when handling the magnet assembly. Another high powered magnet
placed in close proximity (less than 25 mm) can cause permanent damage. Potential sources of damaging equipment
include, but are not limited to: transformers, DC motors, stacking magnet assemblies.
CAUTION
General Guidelines for use of High Power Magnets with Positioners
Use of high power magnets in close proximity to any positioner which is operating a process should be avoided. Regardless
of the positioner model, high power magnets can affect the positioners ability to control the valve. Technicians should
avoid the use of high power magnets in close proximity with any positioner.
Use of Magnetic Tools with the DVC6215

Magnetic Tip Screw Drivers Magnetic tip screw drivers can be used to work on the DVC6215. However, they should
not be brought in close proximity to the magnet assembly (located at the back of the instrument) during process
operations.
Calibrator Strap Magnets These are high power magnets used to hold 4-20 ma calibrators.
Normally, these calibrators would not be used while an instrument is controlling the process.
High power magnets should be kept at least 15 cm (6 inches) from the DVC6215.
Note
(on the back of the DVC6215 housing) has to remain within this range throughout the entire valve travel. See figure 28. The linear
magnet assemblies are symmetrical. Either end may be up.
Figure 28. Travel Range

VALID TRAVEL RANGE
50 mm (2 INCH)
SHOWN
MAGNET ASSEMBLY
(ATTACHED TO VALVE STEM)
INDEX MARK
X0126
17
Installation
August 2012
Instruction Manual
D103412X012
There are a variety of mounting brackets and kits that are used to mount the DVC6215 to different actuators.
Note
The DVC6215 feedback unit uses the same mountings as the DVC6200f digital valve controller.
However, despite subtle differences in fasteners, brackets, and connecting linkages, the procedures for mounting can
be categorized as follows:
Slidingstem linear actuators
Fisher rotary actuators
GX actuator
Quarterturn actuators
See figure 23 for examples of the different travel feedback magnet assemblies.
SlidingStem Linear Actuators up to 210 mm (8.25 Inches) of Travel

The DVC6215 feedback unit has linkageless, noncontact feedback on slidingstem actuators with up to 210 mm
(8.25 inches) travel. Figure 29 shows a typical mounting on a sliding-stem actuator. For actuators with greater than
210 mm (8.25 inches) travel, see the guidelines on page 20.
1. Isolate the control valve from the process line pressure and release pressure from both sides of the valve body. Shut
off all pressure lines to the actuator, releasing all pressure from the actuator. Use lockout procedures to be sure
that the above measures stay in effect while you work on the equipment.
2. Attach the mounting bracket to the actuator.
Figure 29. Mounting Parts for SlidingStem Actuator with up to 210 mm (8.25 inches) Travel
X0127
18
Instruction Manual
Installation
D103412X012
August 2012
3. Loosely attach the feedback pieces and magnet assembly to the valve stem connector. Do not tighten the fasteners
because fine adjustment is required.
CAUTION
Do not install a magnet assembly that is shorter than the physical travel of the actuator. Loss of control will result from the
magnet assembly moving outside the range of the index mark in the feedback slot of the DVC6215 housing.
4. Using the alignment template (supplied with the mounting kit), position the magnet assembly inside the retaining
slot.
5. Align the magnet assembly as follows:
For airtoopen actuators (e.g. Fisher 667) vertically align the magnet assembly so that the center line of the alignment
template is lined up as close as possible with the upper extreme of the valid travel range on the magnet assembly. The
magnet assembly should be positioned so that the index mark in the feedback slot of the DVC6215 housing is within
the valid range on the magnet assembly throughout the range of travel. See figure 210.
For airtoclose actuators (e.g. Fisher 657) vertically align the magnet assembly so that the center line of the alignment
template is lined up as close as possible with the lower extreme of the valid travel range on the magnet assembly. The
magnet assembly should be positioned so that the index mark in the feedback slot of the DVC6215 housing is within
the valid range on the magnet assembly throughout the range of travel. See figure 211.
Figure 210. AirtoOpen Magnet Assembly
Alignment
Figure 211. AirtoClose Magnet Assembly

Alignment
ALIGNMENT
TEMPLATE
RETAINING
SLOT
INDEX
MARK
W9718
RETAINING
SLOT
ALIGNMENT
TEMPLATE
INDEX
MARK
W9719
6. Tighten the fasteners and remove the alignment template.

7. Mount the feedback unit to the mounting bracket, using the mounting bolts.
19
Instruction Manual
Installation
August 2012
D103412X012
8. Check for clearance between the magnet assembly and the DVC6215 feedback slot.
Note
Ensure that there is clearance between the magnet assembly and the DVC6215 housing slot throughout the full range of travel.
Fisher Rotary Actuators and SlidingStem Linear Actuators over 210 mm (8.25 Inches) Travel
The DVC6215 feedback unit uses a cam (designed for linear response) and roller as the feedback mechanism. See
figures 212 and 213.
Figure 212. Mounting on Rotary Actuators
Figure 213. Mounting on SlidingStem (Linear)

Actuators over 210 mm (8.25 Inches) Travel
MOUNTING
ADAPTOR
ROTARY MOUNTING
KIT (DVC6215 NOT
SHOWN)
LONG STROKE
MOUNTING
KIT (DVC6215
NOT SHOWN)
W9709
W9708
Note
All cams supplied with FIELDVUE mounting kits are characterized to provide a linear response.
There are three different mounting adaptions, based on the actuator design (see figure 214).
Fisher Rotary Actuators

Refer to the following guidelines when mounting on rotary actuators.
off all pressure lines to the pneumatic actuator, releasing all pressure from the actuator. Use lockout procedures to
be sure that the above measures stay in effect while working on the equipment.
20
Instruction Manual
Installation
D103412X012
August 2012
2. Verify that the appropriate cam is installed on the actuator as described in the instructions included with the
mounting kit.
3. Mount the DVC6215 on the actuator as follows:
If required, a mounting adaptor is included in the mounting kit. Attach the adaptor to the feedback unit, then
attach the feedback unit assembly to the actuator. The roller on the feedback arm will contact the actuator cam
as it is being attached.
If no mounting adaptor is required, attach the feedback unit and mounting kit assembly to the actuator. The
roller on the feedback arm will contact the actuator cam as it is being attached.
Figure 214. Mounting Variations
ROLLER
ARM
VARIATION A
VARIATION
ROLLER
ARM
ROLLER
ARM
VARIATION B
VARIATION C
ACTUATOR
2052 Size 2 and 3
1051/1052 size 40-70
1061 Size 30-100
SlidingStem > 210 mm (8.25 inches)
B
C
2052 Size 1
1052 Size 20-33
1051 Size 33
NOTE THE DIFFERENCE IN THE SHAPE AND LENGTH OF THE ROLLER ARM
E1229
21
Installation
August 2012
Instruction Manual
D103412X012
SlidingStem Linear Actuators over 210 mm (8.25 Inches) Travel

Refer to the following guidelines when mounting on slidingstem linear actuators over 210 mm (8.25 inches) travel
(see figure 213).
off all pressure lines to the pneumatic actuator, releasing all pressure from the actuator. Use lockout procedures to
be sure that the above measures stay in effect while working on the equipment.
2. Install the cam to the valve stem connector as described in the instructions included with the mounting kit.
3. Install the mounting adaptor to the actuator.
4. Attach the feedback unit and mounting kit assembly to the mounting adaptor. The roller on the feedback arm will
contact the actuator cam as it is being attached.
GX Actuators
The DVC6215 feedback unit mounts directly on the GX actuator without the need for a mounting bracket.
Identify the yoke side to mount the DVC6215 feedback unit based on the actuator fail mode. Refer to the GX Control
Valve and Actuator System instruction manual (D103175X012).
2. Loosely attach the feedback pieces and magnet assembly to the valve stem connector. Do not tighten the fasteners
because fine adjustment is required.
CAUTION
Do not install a magnet assembly that is shorter than the physical travel of the actuator. Loss of control will result from the
magnet assembly moving outside the range of the index mark in the feedback slot of the DVC6215 housing.
3. Using the alignment template (supplied with the mounting kit), position the feedback assembly inside the retaining
slot.
4. Align the magnet assembly as follows:
For airtoopen GX actuators vertically align the magnet assembly so that the center line of the alignment template is
lined up as close as possible with the upper extreme of the valid travel range on the magnet assembly. The magnet
assembly should be positioned so that the index mark in the feedback slot of the DVC6215 housing is within the valid
range on the magnet assembly throughout the range of travel. See figure 215.
For airtoclose GX actuators vertically align the magnet assembly so that the center line of the alignment template is
lined up as close as possible with the lower extreme of the valid travel range on the magnet assembly. The magnet
assembly should be positioned so that the index mark on the pole pieces (back of the DVC6215 housing) is within the
valid range on the magnet assembly throughout the range of travel. See figure 216.
22
Instruction Manual
Installation
D103412X012
August 2012
Figure 215. AirtoOpen Fisher GX Magnet Assembly

Alignment
Figure 216. AirtoClose Fisher GX Magnet Assembly

Alignment
ALIGNMENT TEMPLATE
ALIGNMENT TEMPLATE
RETAINING
SLOT
INDEX MARK
W9218
RETAINING
SLOT
INDEX MARK
W9219
5. Tighten the fasteners and remove the alignment template. Continue on with the appropriate step 6 below.
AirtoOpen GX Actuators
6. The pneumatic output port on the DVC6215 lines up with the integral GX actuator pneumatic port. See figure 217.
7. Using a 5 mm hex wrench, attach the feedback unit to the GX actuator mounting pad on the side that has the open
pneumatic port. Be sure to place the Oring between the feedback units pneumatic output and the actuator
mounting pad. Pneumatic tubing between the feedback unit and the actuator is not required because the air
passages are internal to the actuator.
8. Connect the pneumatic tubing from the DVC6205f to the feedback units pneumatic port provided on the front of
the DVC6215 as shown in figure 217.
10. If not already installed, install a vent in the port on the upper diaphragm casing's air supply connection on the
actuator yoke leg.
23
Instruction Manual
Installation
August 2012
D103412X012
Figure 217. Modifications for Fisher GX Actuator; AirtoOpen Construction Only
PNEUMATIC
PORT
PNEUMATIC TUBING
FROM THE DVC6205f
INSTALL
ORING
X0128
AirtoClose GX Actuators
6. Using a 5 mm hex wrench, attach the feedback unit to the GX actuator mounting pad.
8. Install tubing between the actuator casing and the appropriate DVC6215 pneumatic output port.
9. If not already installed, install a vent in the port on the lower diaphragm casing.
Note
To convert to air-to-open, install an Oring between the feedback units pneumatic output and the actuator mounting pad.
Connect pneumatic tubing from the DVC6205f to the DVC6215. Refer to figure 217.
To convert to air-to-close, remove the Oring between the feedback units pneumatic output and the actuator mounting pad.
Disconnect the pneumatic tubing from the DVC6205f to the DVC6215. Install tubing between the pneumatic output connection
of the DVC6205f to the pneumatic port on top of the actuator casing.
24
Instruction Manual
Installation
D103412X012
August 2012
QuarterTurn Rotary Actuators

The DVC6215 feedback unit can be mounted to any quarterturn rotary actuator, as well as those that comply with the
NAMUR guidelines. A mounting bracket and associated hardware are required. Refer to figure 218.
2. Attach the magnet assembly to the actuator shaft. At midtravel, the flats on the magnet assembly must be parallel
to the channel on the back of the DVC6215 housing, as shown in figure 219.
3. Install the mounting bracket on the actuator.
4. Attach the feedback unit to the mounting bracket using the 4 mounting bolts, as shown in figure 218.
6. Install tubing between the actuator casing and the appropriate DVC6215 pneumatic output port.
Figure 218. Mounting on QuarterTurn Actuators
Figure 219. Magnet Assembly Orientation on

QuarterTurn Actuators
ORIENTATION
AT ONE TRAVEL
EXTREME
ORIENTATION
AT MIDTRAVEL
(FLATS PARALLEL
TO DVC6215
CHANNEL)
M6 MOUNTING
BOLTS (4)
X0129
ORIENTATION
AT THE OTHER
TRAVEL EXTREME
25
Instruction Manual
Installation
August 2012
D103412X012
Fisher 67CFR Filter Regulator

A 67CFR filter regulator, when used with a DVC6200f digital valve controller, can be mounted one of three ways.
IntegralMounted Regulator
Refer to figure 220. Lubricate an Oring and insert it in the recess around the SUPPLY connection on the digital valve
controller. Attach the 67CFR filter regulator to the side of the digital valve controller. Thread a 1/4inch sockethead
pipe plug into the unused outlet on the filter regulator. This is the standard method of mounting the filter regulator.
Figure 220. Mounting the Fisher 67CFR Regulator on a FIELDVUE DVC6200f Digital Valve Controller
67CFR
CAP SCREWS
ORING
NOTE:
1 APPLY LUBRICANT
SUPPLY CONNECTION
W9702-fieldbus
YokeMounted Regulator
Mount the filter regulator with two cap screws to the predrilled and tapped holes in the actuator yoke. Thread a
1/4inch sockethead pipe plug into the unused outlet on the filter regulator. No Oring is required.
CasingMounted Regulator
Use the separate 67CFR filter regulator casing mounting bracket provided with the filter regulator. Attach the
mounting bracket to the 67CFR and then attach this assembly to the actuator casing. Thread a 1/4inch sockethead
pipe plug into the unused outlet on the filter regulator. No Oring is required.
Pneumatic Connections
Pressure
Pressure connections are shown in figure 221. All pressure connections on the digital valve controller are 1/4 NPT
internal connections. Use at least10 mm (3/8inch) tubing for all pressure connections. If remote venting is required a
minimum of 12.7 mm (1/2inch) tubing should be used. Refer to the vent subsection for remote venting information.
26
Instruction Manual
Installation
D103412X012
August 2012
Figure 221. Pressure Connections

LOOP CONNECTIONS
TERMINAL BOX
1/2 NPT CONDUIT
CONNECTION
WIRING
TERMINAL BOX
OUTPUT A
CONNECTION
SUPPLY
CONNECTION
X0379-fieldbus
FEEDBACK CONNECTIONS
TERMINAL BOX
DVC6205f BASE UNIT
W9615-fieldbus
OUTPUT B
CONNECTION
VALVE MOUNTED UNIT
Supply
The DVC6200f can be used with air as the supply medium. In addition, Gas Certified DVC6200f constructions can be
used with natural gas as the supply medium. If using natural gas as the pneumatic supply medium, natural gas will be
used in the pneumatic output connections of the DVC6200f to any connected equipment. In normal operation the
unit will vent the supply medium into the surrounding atmosphere unless it is remotely vented.
WARNING
Not all DVC6200f digital valve controllers are suitable for use with natural gas as the supply medium. If using natural gas as
the supply medium, the DVC6200f must be Gas Certified. Using natural gas as the supply medium in a noncertified
instrument can result in personal injury or property damage.
Gas Certified instruments can be identified by the natural gas approval label shown in figure 222. Contact your Emerson
Process Management sales office for information on obtaining a Gas Certified DVC6200f digital valve controller.
Figure 222. Label for Natural Gas Certified Terminal Box
27
Installation
August 2012
Instruction Manual
D103412X012
WARNING
To avoid personal injury or property damage resulting from bursting or parts, do not exceed maximum supply pressure.
Personal injury or property damage may result from fire or explosion if natural gas is used as the supply medium and
appropriate preventive measures are not taken. Preventive measures may include, but are not limited to, one or more of
the following: Remote venting of the unit, reevaluating the hazardous area classification, ensuring adequate ventilation,
and the removal of any ignition sources. For information on remote venting of this controller, refer to
page 30.
Severe personal injury or property damage may occur from an uncontrolled process if the instrument supply medium is not
clean, dry, oilfree, and noncorrosive. While use and regular maintenance of a filter that removes particles larger than 40
micrometers in diameter will suffice in most applications, check with an Emerson Process Management field office and
industry instrument air quality standards for use with corrosive air or if you are unsure about the amount of air filtration or
filter maintenance.
Supply pressure must be clean, dry air that meets the requirements of ISA Standard 7.0.01. A maximum 40
micrometer particle size in the air system is acceptable. Further filtration down to 5 micrometer particle size is
recommended. Lubricant content is not to exceed 1 ppm weight (w/w) or volume (v/v) basis. Condensation in the air
supply should be minimized.
Alternatively, natural gas may be used as the supply pressure medium in Gas Certified DVC6200f digital valve
controllers. Gas must be clean, dry, oilfree, and noncorrosive. H2S content should not exceed 20 ppm.
If you are using a 67CFR filter regulator with standard 5 micrometer filter, connect the supply line to the 1/4 NPT IN
connection and attach tubing from the output connection on the filter regulator to the SUPPLY connection on the
instrument. If you are using an integral mounted 67CFR filter regulator, connect the supply to the IN connection on
the regulator.
Output Connection
A factory mounted digital valve controller has its output piped to the supply connection on the actuator. If mounting
the digital valve controller in the field, connect the 1/4 NPT digital valve controller output connection to the
pneumatic actuator input connection.
SingleActing Actuators
When using a singleacting direct digital valve controller (relay A or C) on a singleacting actuator, connect OUTPUT A
to the actuator pneumatic input. When using a singleacting reverse digital valve controller (relay B) on a singleacting
actuator, connect OUTPUT B to the actuator diaphragm casing.
DoubleActing Actuators
DVC6200f digital valve controllers on doubleacting actuators always use relay A. With no instrument Fieldbus power
(Zero Power Condition) OUTPUT A is at 0 pressure and OUTPUT B is at full supply pressure when the relay is properly
adjusted. To have the actuator stem extend from the cylinder with increasing input signal, connect OUTPUT A to the
upper actuator cylinder connection. Connect OUTPUT B to the lower cylinder connection. To have the actuator stem
retract into the cylinder with increasing input signal, connect OUTPUT A to the lower actuator cylinder connection.
Connect OUTPUT B to the upper cylinder connection.
28
Instruction Manual
Installation
D103412X012
August 2012
Special Construction to Support Solenoid Valve Testing

Note
Solenoid valve testing is only available for instrument level PD.
In singleacting actuator applications with a solenoid valve installed, the DVC6200f can be configured to monitor the
health of the solenoid valve test, which is initiated by the Logic Solver. This is accomplished by connecting the unused
output port B from the DVC6200f to the pneumatic monitoring line between the solenoid valve and the actuator, as
shown in figure 223. When singleacting, direct relay C is installed, the unused output port is port B. When
singleacting, reverse relay B is used, the unused port is port A.
Figure 223. Pneumatic Hookup for Solenoid Testing (Instrument Level PD only)
24/48 VDC
110/220 VAC, etc.
FOUNDATION FIELDBUS
H1 SEGMENT
CONTROL LINE
Port A
Port B
DVC6200f DIGITAL VALVE

CONTROLLER WITH RELAY C
SUPPLY PRESSURE
MONITORING LINE
NOTES:
1/418 NPT X 3/8 OD TUBING

ELECTRICAL WIRING
SPRING RETURN ACTUATOR
Note
This application is called special application in the Setup Wizard relay selection.
This configuration is not possible with a doubleacting actuator or when using relay A in singleacting mode.
29
Installation
August 2012
Instruction Manual
D103412X012
Vent
WARNING
Personal injury or property damage can occur from cover failure due to overpressure. Ensure that the housing vent
opening is open and free of debris to prevent pressure buildup under the cover.
WARNING
This unit vents the supply medium into the surrounding atmosphere. When installing this unit in a nonhazardous
(nonclassified) location in a confined area, with natural gas as the supply medium, you must remotely vent this unit to a
safe location. Failure to do so could result in personal injury or property damage from fire or explosion, and area
reclassification.
When installing this unit in a hazardous (classified) location remote venting of the unit may be required, depending upon
the area classification, and as specified by the requirements of local, regional, and federal codes, rules and regulations.
Failure to do so when necessary could result in personal injury or property damage from fire or explosion, and area
reclassification.
Vent line piping should comply with local and regional codes, should be as short as possible with a minimum inside
diameter of 12.7 mm (1/2inch), and few bends to reduce case pressure buildup.
In addition to remote venting of the unit, ensure that all caps and covers are correctly installed. Failure to do so could result
in personal injury or property damage from fire or explosion, and area reclassification.
The relay constantly bleeds a small amount of supply medium into the area under the cover. The vent opening, located
below the wiring terminal box on the side of the housing, should be left open to prevent pressure buildup under the
cover. If a remote vent is required, the vent lines must be as short as possible with a minimum number of bends and
elbows.
To connect a remote vent, remove the plastic vent. The vent connection is 3/8 NPT. At a minimum, 12.7 mm
(1/2inch) tubing should be used when installing a remote vent to prevent excessive pressure from building up under
the cover.
30
Instruction Manual
D103412X012
Installation
August 2012
Wiring and Electrical Connections

Connecting Fieldbus Wiring
The digital valve controller is normally powered over the bus from a fieldbus power supply. Refer to the site planning
guide for proper wire types, termination, length, etc. for a fieldbus loop.
Note
As shipped from the factory, the DVC6200f digital valve controller will not move the valve when power is applied to the
instrument. To avoid the valve going to an unknown position when power is applied, the unit is shipped from the factory with the
transducer block mode Out of Service. See the Basic Setup section for information on setup and calibration and placing the
instrument in service.
WARNING
To avoid personal injury resulting from electrical shock, do not exceed the maximum input voltage specified in table 11 of
this quick start guide, or on the product nameplate. If the input voltage specified differs, do not exceed the lowest specified
maximum input voltage.
WARNING
Select wiring and/or cable glands that are rated for the environment of use (such as hazardous area, ingress protection and
temperature). Failure to use properly rated wiring and/or cable glands can result in personal injury or property damage
from fire or explosion.
Wiring connections must be in accordance with local, regional, and national codes for any given hazardous area approval.
Failure to follow the local, regional, and national codes could result in personal injury or property damage from fire or
explosion
Personal injury or property damage caused by fire or explosion may occur if this connection is attempted in a potentially
explosive atmosphere or in an area that has been classified as hazardous. Confirm that area classification and atmosphere
conditions permit the safe removal of the terminal box cover before proceeding.
31
Instruction Manual
Installation
August 2012
D103412X012
Twisted Shielded Pair

Refer to figure 82 for identification of parts.
Wire the digital valve controller as follows, refer to figure 224:
Figure 224. Loop Connections Terminal Box
SAFETY
GROUND
TALK
TALK
EARTH
GROUND
LOOP
LOOP
GE41456-A
1. Remove the wiring terminal box cap.

2. Bring the field wiring into the terminal box. When applicable, install conduit using local and national electrical codes
which apply to the application.
3. The instrument is not polarity sensitive. Connect one wire from the H1 card output to one of the LOOP screw
terminals on the pwb/terminal strip assembly in the terminal box shown in figure 224. Connect the other wire from
the H1 card output to the other LOOP screw terminal in the terminal box.
WARNING
Personal injury or property damage can result from the discharge of static electricity. Connect a 14 AWG (2.08 mm2)
ground strap between the digital valve controller and earth ground when flammable or hazardous gases are present. Refer
to national and local codes and standards for grounding requirements.
4. As shown in figure 224, two ground terminals are available for connecting a safety ground, earth ground, or drain
wire. The safety ground terminal is electrically identical to the earth ground. Make connections to these terminals
following national and local codes and plant standards.
WARNING
32
Instruction Manual
Installation
D103412X012
August 2012
5. Replace and hand tighten the cover on the terminal box. To secure the terminal box cap engage the lock screw.
When the loop is ready for startup, apply power to the H1 card output.
Quick Connect Cable Entry

The DVC6200f is offered with a quick connect cable entry option, shown in figure 225, for the FOUNDATION fieldbus
signal. The quick connect cable entry provides an easier and more reliable interface to fieldbus devices and support
modules by providing a standard connection.
Figure 225. Quick Connect Connector
1 (BLUE)
2 (BROWN)
3 (NC)
4 (GREEN/YELLOW)
1/214 NPT
NOTES:
1.COLORS ARE WIRE COLORS.
2.NC=NO CONNECTION.
18B9424A
Note
The quick connect cable entry option is only available for intrinsically safe and nonincendive installations.
Refer to figure 82 for identification of parts.
WARNING
Personal injury or property damage, caused by fire or explosion, can result from the discharge of static electricity. Connect
a 14 AWG (2.08 mm2) ground strap between the digital valve controller and earth ground when flammable or hazardous
gases are present. Refer to national and local codes and standards for grounding requirements.
To avoid static discharge from the plastic cover, do not rub or clean the cover with solvents. Clean with a mild detergent
and water only.
To avoid personal injury or property damage, do not use the Quick Connect option on instruments in explosionproof or
flameproof installations.
1. The quick connect cable entry should be installed on the digital valve controller at the factory. If it is, proceed to
step 3. If not continue with step 2.
2. To install the Quick Connect:
a. Remove the terminal box cap (key 4) from the terminal box (key 3).
b. Apply sealant to the threads of the quick connector.
c. Insert the wire pigtail into the desired conduit opening on the terminal box. Tighten the quick connector in the
conduit opening.
d. Cut and trim the wire ends.
33
Installation
August 2012
Instruction Manual
D103412X012
e. The instrument is not polarity sensitive. Refer to figure 224. Connect the blue wire to one of the LOOP terminals
in the terminal box. Connect the brown wire to the other LOOP terminal. Cut the green/yellow wire off inside of
the DVC6200f, and ensure that the shield is totally isolated at the instrument end.
Note
The green/yellow wire is cut off inside the DVC6200f to help prevent ground loop issues. The only wires that should be installed
and left on the connector are the two signal wires.
f. Replace the terminal box cap on the terminal box. To secure the terminal box cap engage the lock screw.
3. Connect the field wiring connector to the installed quick connector.
Remote Travel Sensor Connections

The DVC6205f base unit is designed to receive travel information via the Emerson Process Management supplied
DVC6215 feedback unit.
WARNING
Personal injury or property damage, caused by wiring failure, can result if the feedback wiring connecting the base unit
with the remote feedback unit shares a conduit with any other power or signal wiring.
Do not place feedback wiring in the same conduit as other power or signal wiring.
Note
4conductor shielded cable, 18 to 22 AWG minimum wire size, in rigid or flexible metal conduit, is required for connection
between base unit and feedback unit. Pneumatic tubing between base unit output connection and actuator has been tested to 15
meters (50 feet) maximum without performance degradation.
1. On the feedback unit, remove the housing cap.

2. On the base unit, remove the feedback connections terminal box cap (see figure 221).
3. Install conduit between the feedback unit and the base unit following applicable local and national electrical codes.
Route the 4conductor shielded cable between the two units (refer to figure 226).
4. Connect one wire of the 4conductor shielded cable between terminal 1 on the feedback unit and terminal 1 on the
base unit.
5. Connect the second wire of the 4conductor shielded cable between terminal 2 on the feedback unit and terminal 2
on the base unit.
6. Connect the third wire of the 4conductor shielded cable between terminal 3 on the feedback unit and terminal 3
on the base unit.
7. Connect the fourth wire of the 4conductor shielded cable between terminal 4 on the feedback unit and terminal 4
on the base unit.
34
Instruction Manual
Installation
D103412X012
August 2012
Figure 226. Terminal Details for Connecting the Base Unit and Feedback Unit for RemoteMounted Digital Valve
Controllers
FEEDBACK
CONNECTIONS
TERMINAL BOX
X0131-FF
FEEDBACK UNIT
GROUND
SCREW
BASE UNIT
TO FEEDBACK UNIT TERMINAL 1
TO FEEDBACK UNIT TERMINAL S

USING CABLE SHIELD
FEEDBACK CONNECTIONS
TERMINAL BOX
TERMINAL 1
TERMINAL 2
TERMINAL S
TERMINAL 4
TERMINAL 3
FEEDBACK UNIT
WARNING
The cable shield is typically not insulated. It is required that you insulate the cable shield prior to installation.
When connecting the cable shield in step 8 ensure that the uninsulated shield wiring does not contact the DVC6215
housing. Failure to do so can result in ground loop issues.
8. Connect the cable shield between terminal S on the feedback unit and terminal S on the base unit.
CAUTION
Failure to secure the cable wires in the support clips in step 9 can cause wires to break in applications with high levels of
vibration.
9. Secure the cable wires, using the support clips in the DVC6215 feedback unit (as shown in figure 227), to help
prevent shifting and movement of the wires.
10. Replace and handtighten all covers.
35
Instruction Manual
Installation
August 2012
D103412X012
Figure 227. Secure Wires in Clips

CLIP TO SUPPORT THE WIRES OF
THE 4-CONDUCTOR SHIELDED CABLE
CLIP TO SUPPORT THE
INSULATED SHIELD WIRE
Communication Connections
WARNING
conditions permit the safe removal of the terminal box cap before proceeding.
A FOUNDATION fieldbus communicating device, such as a Field Communicator or a personal computer running
ValveLink software, interfaces with the DVC6200f digital valve controller from any wiring termination point in the
segment. If you choose to connect the fieldbus communicating device directly to the instrument, attach the device to
the LOCAL connections inside the terminal box to provide local communications with the instrument.
Simulate Enable Jumper

WARNING
conditions permit the safe removal of the terminal box cap before proceeding.
Install a jumper across the SIMULATE ENABLE terminals to enable the instrument to accept a simulate command.
(These terminals are marked AUX on the terminal board, see figure 224). With the jumper in place and the simulate
parameter in the AO or DO block set to enabled, the transducer block ignores the output of the AO or DO block. The
simulate value and status become the readback value and status to the AO or DO block and the transducer block is
ignored. For more information on running simulations, see the Detailed Setup section of this manual, the FOUNDATION
fieldbus specifications, and the host documentation.
WARNING
Removing the jumper will disable the simulate, which may cause the valve to move. To avoid personal injury and property
damage caused by the release of pressure or process fluid, provide some temporary means of control for the process.
36
Instruction Manual
D103412X012
Installation
August 2012
Commissioning Tag
The DVC6200f digital valve controller is supplied with a removable paper commissioning tag, shown in figure 228.
This tag contains both the device ID and a space to record the device's tag number. The device ID is a unique code that
identifies a particular device in the absence of a device tag. The device tag is used as an operational identification for
the device and is usually defined by the piping and instrumentation diagram (P&ID).
Figure 228. Paper Commissioning Tag
18B9406G
When commissioning more than one device on a fieldbus segment, identifying which device is at a particular location
can be tedious without tags. The removable tag provided with the digital valve controller can be used to link the
device ID and the physical installation location. The installer should note the physical location in both places on the
removable commissioning tag and tear off the bottom portion. This should be done for each device on the segment.
The bottom portion of the tags can be used for commissioning the segment in the control system.
Prior to commissioning, the device ID is displayed by the host system if no device tag is configured in the digital valve
controller electronics. Typically the placeholder displays the device tag. The information on the paper tag enables the
engineer to match the device ID to the correct placeholder.
As an ordering option, the factory can enter a device tag into the digital valve controller electronics during the
manufacturing process. If this option is specified, the device tag is displayed at the host system prior to commissioning
rather than the device ID. This makes the job of commissioning the device easier.
37
Installation
August 2012
38
Instruction Manual
D103412X012
Instruction Manual
Basic Setup
D103412X012
August 2012
Section 3 Basic Setup3-3Basic Setup

Field Communicator
TB > Configure/Setup > Basic Setup
WARNING
Changes to the instrument setup may cause changes in the output pressure or valve travel. Depending on the application,
these changes may upset process control, which may result in personal injury or property damage.
When the DVC6200f digital valve controller is ordered as part of a control valve assembly, the factory mounts the
digital valve controller and sets up the instrument as specified on the order. When mounting to a valve in the field, the
instrument needs to be setup to match the instrument to the valve and actuator.
Before beginning basic setup, be sure the instrument is correctly mounted as described in the Installation section.
Basic Setup includes the following procedures:
Device Setup
Auto Travel Calibrate
Performance Tuner (Optional)
Note
The DVC6200f may keep the Transducer Block Mode OutofService if the instrument is not properly mounted.
To setup and calibrate the instrument, the Transducer Block Mode must be Manual, and the Protection must be None.
When using DD methods the method will request that you change the mode, but make changes in Protection automatically. If you
have a host system that overrides transducer block parameters ensure that the Protection setting is not left as None. Doing so will
result in transducer block parameters being overwritten.
Transducer Block Mode

Field Communicator
TB > Configure/Setup > Detailed Setup > Transducer Block Mode
To setup and calibrate the instrument, the transducer block mode must be in Manual. For more information about
transducer block mode, refer to page 62.
Protection
Field Communicator
TB > Configure/Setup > Detailed Setup > Protection
To setup and calibrate the instrument, the protection must be set to None with the Field Communicator. For more
information about configuration protection refer to page 62.
39
Instruction Manual
Basic Setup
August 2012
D103412X012
Device Setup
Field Communicator
TB > Configure/Setup > Basic Setup > Device Setup
Follow the prompts on the Field Communicator display to automatically setup the instrument using specified actuator
information. Table 32 provides the actuator information required to setup and calibrate the instrument.
Note
If reverseacting relay B is used, you must manually set the Relay Type (BASIC_SETUP.RELAY_TYPE [42.5]) to B. This will not be set
during Device Setup.
1. Select whether Travel, Travel with Pressure fallback (auto recovery or manual recovery) or Pressure Control is
desired. Refer to page 66 for additional information.
2. Enter the pressure units:kPa, bar, psi, inHg, inH2O, or kg/cm2.
3. Enter the maximum instrument supply pressure and output pressure range (if required).
4. Enter the manufacturer of the actuator on which the instrument is mounted. If the actuator manufacturer is not
listed, select Other.
5. Enter the actuator model or type. If the actuator model is not listed, select Other.
6. Enter the actuator size.
7. Indicate whether a Volume Booster is being used.
8. Specify if factory defaults should be used for basic setup. If you select YES for factory default, the Field
Communicator sets the setup parameters to the values listed in table 31. If you select NO for the factory defaults,
the setup parameters listed in the table remain at their previous settings.
Table 31. Factory Default Settings
Setup Parameter
Default Setting
Travel Cutoff Hi
Travel Cutoff Lo
Travel Integral Gain
Travel Calibration Trigger
99.5%
0.5%
9.4 repeats/min
No
Travel Integral Enable

Travel Integral Limit Hi
Travel Integral Limit Lo
Travel Integral Deadzone
On
30%
-30%
0.25%
Pressure Cutoff Hi
Pressure Cutoff Lo
Pressure Integral Deadzone
Pressure Integral Hi Limit
Pressure Integral Lo Limit
99.5%
-0.5%
0.25%
50.0%
-50.0%
Input Characterization
Shutdown Trigger
Shutdown Recovery
Output Block Timeout
Linear
All Off
All Auto Recovery
600 sec
40
Instruction Manual
Basic Setup
D103412X012
August 2012
Table 32. Actuator Information for Initial Setup

Actuator
Manufacturer
Actuator Model
585C & 585CR
657
667
1051 & 1052
1061
Fisher
Actuator Size
Actuator Style
25
50
60
68, 80
100, 130
30
34, 40
45, 50
46, 60, 70, 76, &
80100
30
34, 40
45, 50
46, 60, 70, 76, &
80100
20, 30
33
40
60, 70
Piston Dbl w/ or w/o

Spring. See actuator
instruction manual and
nameplate.
30
40
60
68, 80, 100, 130
Starting
Tuning Set
Travel Sensor Motion(2)

Relay A or C(3)
E
I
J
L
M
User Specified
Spring & Diaphragm
H
K
L
Away from the top of the instrument
Spring & Diaphragm
M
H
K
L
Towards the top of the instrument
Spring & Diaphragm

(Window-mount)
Piston Dbl w/o Spring
M
H
I
K
M
J
K
L
M
Depends upon pneumatic connections. See

description for Travel Sensor Motion
Mounting Style
A
1066SR
20
27, 75
Piston Sgl w/Spring
G
L
B
C
D
2052
1
2
3
3024
30, 30E
34, 34E, 40, 40E
45, 45E
Spring & Diaphragm

(Window-mount)
H
K
M
Spring & Diaphragm
E
H
K
For Po operating mode (air opens):

For Ps operating mode (air closes):
X(1)
225
GX
Air to Extend
Air to Retract
Baumann
Rotary
750
Travel Sensor Motion

Away from the top of the
instrument
Towards the top of the
instrument
Towards the top of the
instrument
instrument
Spring & Diaphragm
1200
16
32
54
10
25
54
C
E
H
E
H
J
Spring & Diaphragm
Air to Open
Towards the top
of the instrument
Air to Close
instrument

Specify
NOTE: Refer to figure 23 and table 410 for feedback connection (magnet assembly) information.
1. X = Expert Tuning. Proportional Gain = 4.2; Velocity Gain = 3.0; Minor Loop Feedback Gain = 18.0
2. Travel Sensor Motion in this instance refers to the motion of the magnet assembly.
3. Values shown are for Relay A and C. Reverse for Relay B.
41
Basic Setup
Instruction Manual
August 2012
D103412X012
Typically Device Setup determines the required setup information based upon the actuator manufacturer and model
specified. However, if you enter OTHER for the actuator manufacturer or the actuator model, then you will be
prompted for setup parameters such as:
Actuator StyleSelect spring & diaphragm, piston doubleacting without spring, piston singleacting with spring,
piston doubleacting with spring.
Valve StyleSelect the valve style, rotary or slidingstem.
Zero Power Conditionthis identifies whether the valve is fully open or fully closed when the input is 0%. If you are
unsure how to set this parameter, disconnect the instrument from the segment. (With doubleacting and
singleacting direct digital valve controllers, disconnecting the instrument from the segment is the same as setting
the output A pressure to zero. For singleacting reverse digital valve controllers, disconnecting the instrument from
the segment is the same as setting the output B pressure to supply.)
WARNING
If you answer YES to the prompt for permission to move the valve when setting the Travel Sensor Motion, the instrument
will move the valve through its full travel range. To avoid personal injury and property damage caused by the release of
pressure or process fluid, isolate the valve from the process and equalize pressure on both sides of the valve or bleed off the
process fluid.
Travel Sensor MotionDevice Setup asks if it can move the valve to determine travel sensor motion. If you answer
Yes, the instrument will stroke the valve the full travel span to determine travel sensor motion. If you answer No,
then you must specify the direction of travel movement. For quarterturn actuators determine rotation by viewing
the rotation of the magnet assembly from the back of the instrument.
Note
Travel Sensor Motion in this instance refers to the motion of the magnet assembly. Note that the magnet assembly may be
referred to as a magnetic array in user interface tools.
For instruments with relay A or C If increasing air pressure at output A causes the magnet assembly to move up, or
the actuator shaft to rotate counterclockwise, enter Towards Top of Instrument/CCW. If it causes the magnet
assembly to move down, or the actuator shaft to rotate clockwise, enter Away From Top of Instrument/CW. For
instruments with relay B.
For instruments with relay B If decreasing air pressure at output B causes the magnet assembly to move up, or the
actuator shaft to rotate counterclockwise, enter Towards Top of Instrument/CCW. If it causes the magnet
assembly to move down, or the actuator shaft to rotate clockwise, enter Away From Top of Instrument/CW.
Note
Relay A adjustment may be required before Device Setup can determine travel sensor motion. Follow the prompts on the Field
Communicator display if relay adjustment is necessary.
Table 32 lists the required Travel Sensor Motion selections for Fisher and Baumann actuators.
42
Instruction Manual
Basic Setup
D103412X012
August 2012
Tuning SetThere are twelve tuning sets to choose from. Each tuning set provides a preselected value for the digital
valve controller gain settings. Tuning set C provides the slowest response and M provides the fastest response. For
smaller actuators use tuning set C or D. For larger actuators using tuning set F or G. Table 33 lists the values for
preselected tuning sets.
Note
Tuning set B is only available in Pressure Control Mode.
Table 33. Gain Values for Preselected Tuning Sets

Travel
Tuning Set
B
C
D
E
F
G
H
I
J
K
L
M
X (Expert)
Proportional Gain
4.4
4.8
5.5
6.2
7.2
8.4
9.7
11.3
13.1
15.5
18.0
User Adjusted
Pressure
Velocity Gain
Minor Loop
Feedback Gain
Proportional Gain
Integrator Gain
Minor Loop
Feedback Gain
3.0
3.0
3.0
3.1
3.6
4.2
4.8
5.6
6.0
6.0
6.0
User Adjusted
35
35
35
35
34
31
27
23
18
12
12
User Adjusted
0.5
2.2
2.4
2.8
3.1
3.6
4.2
4.8
5.6
6.6
7.8
9.0
User Adjusted
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
User Adjusted
35
35
35
35
35
34
31
27
23
18
12
12
User Adjusted
WARNING
Changes to the tuning set may cause the valve/actuator assembly to stroke. To avoid personal injury or property damage
caused by moving parts, keep hands, tools, and other objects away from the valve/actuator assembly.
In addition, you can select Expert, which allows you to individually set the proportional gain, velocity gain, and minor
loop feedback gain for travel tuning and pressure proportional gain, pressure integrator gain, and pressure minor loop
feedback gain for pressure tuning. Refer to page 63 for additional information on travel tuning and page 65 for
pressure tuning.
Note
Use Expert tuning only if standard tuning has not achieved the desired results.
Stabilize/Optimize or Performance Tuner may be used to achieve the desired results more rapidly than expert tuning.
Table 32 provides tuning set selection guidelines for Fisher and Baumann actuators. These tuning sets are only
recommended starting points. After you finish setting up and calibrating the instrument, use Stabilize/Optimize to
adjust the tuning set to get the desired response.
43
Instruction Manual
Basic Setup
August 2012
D103412X012
When Device Setup is complete you are asked if you wish to run Auto Calibration now. Select yes to automatically
calibrate instrument travel at this time. Follow the prompts on the Field Communicator display. The calibration
procedure uses the valve and actuator stops as the 0% and 100% calibration points. For additional information, refer to
Auto Calibration in the Calibration section.
Note
Singleacting relay B and C are not useradjustable. However, it is recommended that you check the relay adjustment for
doubleacting relay A in new installations before proceeding with travel calibration.
Refer to page 215 for relay adjustment instructions.
If after completing setup and calibration the valve cycles or overshoots (unstable), or is unresponsive (sluggish), you
can improve operation by running Performance Tuner or Stabilize/Optimize.
Performance Tuner
Field Communicator
TB > Configure/Setup > Basic Setup > Performance Tuner
WARNING
During performance tuning the valve may move, causing process fluid or pressure to be released. To avoid personal injury
and property damage caused by the release of process fluid or pressure, isolate the valve from the process and equalize
pressure on both sides of the valve or bleed off the process fluid.
The Performance Tuner is used to determine digital valve controller tuning. It will move the valve slightly and monitor
the effects of small tuning changes until an optimum control response is achieved. Because the Performance Tuner
can detect internal instabilities before they become apparent in the travel response, it can generally optimize tuning
more effectively than manual tuning. Typically, the Performance Tuner takes 3 to 5 minutes to tune an instrument,
although tuning instruments mounted on larger actuators may take longer.
44
Instruction Manual
D103412X012
Detailed SetupResource Block

August 2012
Section 4 Detailed Setup 4-4Resource Block

Overview
The resource block contains the hardware specific characteristics associated with a device; it has no input or output
parameters. The resource block monitors and controls the general operation of other blocks within the device. Most of
the resource block parameters are operational parameters that provide information about the instrument such as
identification, hardware information, available options, etc. and are read only. Configuration of the resource block
involves selecting features from those that are available, setting the mode, setting write lock, and setting up alert
reporting details.
The following procedures address only the key resource block parameters; however, all resource block parameters are
listed in table 43.
Configure/Setup
Setup
Resource Block Mode
Field Communicator
RB > Configure/Setup > Setup > Resource Block Mode
Modes
The resource block can be in one of two modes (MODE_BLK [5]):
Automatic (Auto)This is the operational mode for this block. When the resource block is in the Auto mode, all
other function blocks are allowed to function normally.
Out of Service (OOS)Placing the resource block in Out of Service mode stops all function block execution, by
setting their modes to Out of Service as well. The actual mode of the function blocks is changed to Out of Service, but
the function block target modes are retained. Placing the resource block in the Out of Service mode does not affect
the mode of the transducer block.
Write Lock
Field Communicator
RB > Configure/Setup > Write Lock
Write Lock
Write Lock (WRITE_LOCK [34]) determines if writes are permissible to other device parameters. The Firmware Write
Lock feature must be selected to be able to use Write Lock (see Features). When Write Lock is set to Locked, no writes
are permitted to any parameters within the device except to set Write Lock to Not Locked. When locked, the device
functions normally, updating inputs and outputs and executing algorithms. When Write Lock is set to Not Locked, the
Write Alarm (WRITE_ALM [40]) alert is active.
45
Instruction Manual
August 2012
D103412X012
Write Priority
Write Priority (WRITE_PRI [39]) sets the priority for Write Alarm. The lowest priority is 0. The highest is 15.
Communication Time Out

Field Communicator
RB > Configure/Setup > Communication Time Out
Shed Remote Cascade
Note
Typically this parameter does not need to be changed. The unit will be operational using the default values assigned by the factory.
Perform this procedure only if a remote computer is sending setpoints from your advanced control.
Default value for RCas Timeout is 20 seconds.
Shed Remote Cascade (SHED_RCAS [26]) determines how long function blocks in the DVC6200f should wait before
giving up on remote computer writes to RCas parameters. When the timeout is exceeded, the block sheds to the next
mode as defined by the block shed options. If Shed Remote Cascade is set to 0, the block will not shed from RCas.
Enter a positive value in the Shed Remote Cascade field. Time duration is in 1/32 milliseconds (640000 = 20 secs).
Shed Remote Out
Note
Perform this procedure only if a remote computer is sending setpoints from your advanced control.
Default value for Shed Remote Out is 20 seconds.
Shed Remote Out (SHED_ROUT [27]) determine how long function blocks in the DVC6200f should wait before giving
up on computer writes to ROut parameters. When the timeout is exceeded, the block sheds to the next mode as
defined by the block shed options. If Shed Remote Out is set to 0, the block will not shed from ROut. Enter a positive
value in the Shed Remote Out field. Time duration is in 1/32 milliseconds (640000 = 20 secs).
Options
Field Communicator
RB > Configure/Setup > Options
Diagnostic Options
Diagnostic Options (DIAG_OPTIONS [45]) shows the diagnostic options available in the instrument.
Function Block Options
Function Block Options (FB_OPTIONS [44]) shows which function blocks are available in the instrument.
46
Instruction Manual
D103412X012
August 2012
Miscellaneous Options
Miscellaneous Options (MISC_OPTIONS [46]) indicates which miscellaneous licensing options are enabled.
Features Available
Features Available (FEATURES [17]) indicates which Resource Block Options features are available.
ReportsReports enables alert and event reporting. Reporting of specific alerts may be suppressed. See Alerts on
page 69.
Fault StateFault state enables the ability of the output block to react to various abnormal conditions by
shedding mode. See parameter descriptions for Set Fault State (SET_FSTATE [29]) and Clear Fault State
(CLR_FSTATE [30]) in table 43 and Action on Fault Detection.
Soft Write LockSoft Write lock permits using Write Lock (WRITE_LOCK [34]) to prevent any external change to
parameter values. Block connections and calculation results will proceed normally, but the configuration is locked.
Also see Write Lock, on page 45.
Multibit Alarm (BitAlarm) Support Multibit Alarm (BitAlarm) Support permits the instrument to treat each
PlantWeb alert separately when broadcast to the Host. Without MultiBit Alarm Support, an individual PlantWeb
alert must be acknowledged before another PlantWeb alert can be broadcast to the Host
Features Selected
Note
Fault State, Software Write Lock, and Output Readback are set by default.
Features Selected (FEATURE_SEL [18]) indicates which Resource Block Options features have been selected and is used
to select the desired features.
ReportsSelecting reports enables alert and event reporting. Reporting of specific alerts may be suppressed. See
Alerts on page 69.
Fault StateSelecting fault state enables the ability of the output block to react to various abnormal conditions by
shedding mode. See parameter descriptions for Set Fault State (SET_FSTATE [29]) and Clear Fault State
(CLR_FSTATE [30]) in table 43 and Action on Fault Detection.
Soft Write LockWhen selected, permits using Write Lock (WRITE_LOCK [34]) to prevent any external change to
parameter values. Block connections and calculation results will proceed normally, but the configuration is locked.
Also see Write Lock, on page 45.
Multibit Alarm (BitAlarm) Support When selected, the instrument will allow the instrument to treat each
PlantWeb alert separately when broadcast to the Host.
Alarm Handling
Field Communicator
RB > Configure/Setup > Alarm Handling
Alert KeyAlert Key (ALERT_KEY [4]) is a number that permits grouping alerts. This number may be used to indicate
to the operator the source of the alert, such as the instrument, plant unit, etc. Enter a value between 1 and 255.
47
Instruction Manual
August 2012
D103412X012
Confirm TimeConfirm Time (CONFIRM_TIME [33]) determines the time, in 1/32 of a millisecond, the instrument
waits for confirmation of receipt of a report before trying again. If Confirm Time is 0, the instrument does not retry
to send the report. Enter 0 or a value between 320000 (10 secs) and 640000 (20 secs).
Limit NotifyLimit Notify (LIM_NOTIFY [32]) is the number of alert reports that the device can send without getting
a confirmation up to the maximum permitted in Maximum Notify (MAX_NOTIFY [31]). If Limit Notify is set to zero,
no alerts are reported. Enter a value between 0 and 3.
To have the instrument report alerts without having the host poll the alerts parameters, select the Reports feature
(see Feature Select).
Maximum NotifyMaximum Notify (MAX_NOTIFY [31]) indicates the maximum number of alert reports that the
device can send without getting a confirmation. This limit is determined by the amount of memory available for
alert messages. The number can be set lower, to control alert flooding, by adjusting Maximum Alerts Allowed
(LIM_NOTIFY [32]).
Block Alarm DisabledThe Block Alarm (BLOCK_ALM [36]) is used for all configuration, hardware, connection failure
or system problems in the block. Alarm Summary (ALARM_SUM [37]) determines if the Write Alarm (WRITE_ALM
[40]) and Block Alarm [BLOCK_ALM [36]) are disabled.
Block Alarm Auto AcknowledgeAcknowledge Option (ACK_OPTION [38]) determines if the block alarm will be
automatically acknowledged.
Discrete Alarm DisabledThe Write Alarm (WRITE_ALM [40]) is used to alert when parameters are writeable to the
device. Alarm Summary (ALARM_SUM [37]) determines if the Discrete Alarm is disabled.
Discrete Alarm Auto AcknowledgeAcknowledge Option (ACK_OPTION [38]) determines if the Write Alarm
associated with the block will be automatically acknowledged.
Identification
Field Communicator
RB > Configure/Setup > Identification
Device IDThe 32 character Device ID (DEVICE_ID [54]).

Electronics Serial NumberThe Electronics Serial Number (ELECTRONICS_SN [49]) set at the factory.
Factory Serial NumberThe Factory Serial Number (FACTORY_SN [50]) is the instrument serial number set at the
factory.
Field Serial NumberThe Field Serial Number (FIELD_SN [51]) is the serial number of instrument assigned in field.
Tag DescriptionThe Tag Description (TAG_DESC [2]) is used to assign a unique 32 character description to each
block within the digital valve controller to describe the intended application for the block.
StrategyStrategy (STRATEGY [3]) permits strategic grouping of blocks so the operator can identify where the
block is located. The blocks may be grouped by plant area, plant equipment, etc. Enter a value between 0 and
65535 in the Strategy field.
ManufacturerManufacturer Identification (MANUFAC_ID [10]) identifies the manufacturer of the instrument. It is
used by the host system to locate the DD file for the device. For Fisher the Manufacturer ID is 0x5100.
Device TypeDevice Type (DEV_TYPE [11]) identifies the type of device. It is used by the host system to locate the
DD file for the device. For a DVC6200f digital valve controller the device type is 0x4602.
48
Instruction Manual
D103412X012
August 2012
Diagnostic OptionsDiagnostic Options (DIAG_OPTIONS [45]) shows the diagnostic options available in the
instrument.
Version
Field Communicator
RB > Configure/Setup > Version
Device RevisionThe Device Revision (DEV_REV [12]) is the manufacturer's revision number associated with the
resource, used by an interface device to locate the DD file for the resource.
Firmware RevisionFirmware Revision (FIRMWARE_REVISION [47]) identifies the revision of the firmware that is
currently in use.
Standby Firmware RevisionStandby Firmware Revision (STBY_FIRMWARE_REVISION [55]) identifies the revision of
the alternative firmware.
Hardware RevisionHardware Revision (HARDWARE_REV [48]) identifies the revision of the electronic hardware.
ITK VersionITK Version (ITK_VER [41]) identifies the major version of the Interoperability Tester used by the
Fieldbus Foundation in certifying the device as interoperable. This device revision meets the requirements of
version 5.
Block Errors
Table 41 lists conditions reported in the BLOCK_ERR [6] parameter. Conditions in italics are not applicable for the
Resource block and are provided only for your reference.
Table 41. Resource Block BLOCK_ERR Conditions
Condition Number
Condition Name and Description
Other Set if a device initialization error occurred.
Block Configuration Error Set if FEATURE_SEL, CYCLE_SEL, or CYCLE_TYPE is set incorrectly.
Link Configuration Error N/A
Simulate Active Indicates that the simulation jumper is in place on the aux terminals. This is not an indication that the I/O
blocks are using simulation data. See AO block parameter SIMULATE [10] and DO block parameter SIMULATE_D [10].
Local Override N/A
Device Fault State Indicates the device is in Fault State.
Device Needs Maintenance Soon Indicates a Maintenance or Advisory PlantWeb Alert condition is active.
Input failure/process variable had Bad status N/A
Output failure N/A
Memory failure Indicates a pending Flash or NVM failure.
10
Lost Static Data Indicates failure of the memory containing static parameters.
11
Lost NV Data Indicates failure of the memory containing nonvolatile parameters.
12
Readback Check Failed NA
13
Device Needs Maintenance Now Indicates a Failed PlantWeb Alert condition is active.
14
Power Up Indicates the device has been powered up and the Resource Block is not running normally.
15
Out of Service (MSB) The resource block actual mode is Out of Service.
49
Instruction Manual

August 2012
D103412X012
Table 42. Parameters Affected by Restart with

Defaults
Index
Number
Parameter Name
Initial Value

Defaults (Continued)
Index
Number
Parameter Name
AO Block (continued)
Resource Block
1
2
3
4
ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
0
spaces
0
0
MODE_BLK
TARGET
PERMITTED
NORMAL
Auto
Auto or Out of Service
Auto
14
18
20
GRANT_DENY
FEATURE_SEL
CYCLE_SEL
All bits: 0
Set by mfgr.
0:0
26
27
28
SHED_RCAS
SHED_ROUT
FAULT_STATE
640000
640000
1=Clear
32
33
34
37
LIM_NOTIFY
CONFIRM_TIME
WRITE_LOCK
ALARM_SUM
DISABLED
MAX_NOTIFY
640000
1=Unlocked
ACK_OPTION
WRITE_PRI
Disabled
0
38
39
All bits: 0
23
24
26
ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
MODE_BLK
TARGET
PERMITTED
NORMAL
SP
OUT
8
9
11
12
0
spaces
0
0
Value
SHED_OPT
1
2
3
4
ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
MODE_BLK
TARGET
PERMITTED
14
15
XD_SCALE
EU 100%
EU 0%
Engineering Units
Decimal Places
IO_OPTS
STATUS_OPTS
17
CAS_IN
PV_SCALE
EU 100%
EU 0%
Engineering Units
Decimal Places
100
0
%
2
13
14
OUT_SCALE
EU 100%
EU 0%
Engineering Units
Decimal Places
CONTROL_OPTS
STATUS_OPTS
100
0
%
2
0: Bypass enable
All off
15
IN
10
11
18
19
20
21
22
SP_RATE_DN
SP_RATE_UP
SP_HI_LIM
SP_LO_LIM
CHANNEL
-Continued-
BAD:
NC:
const
0
0
Status
16
BAD:
NC:
const
0
+INF
+INF
100
0
1=analog valve input
0
spaces
0
0
NORMAL
SP
OUT
8
9
100
0
%
2
100
0
%
2
All off
All off
BAD:
NoComm:
NoVal:
const
0 Trk
All off
Out of Service
OOS+MAN+AUTO+CAS+
RCAS+ROUT
Auto
Dynamic
Dynamic
OOS+MAN+AUTO+CAS+RCAS
PV_SCALE
EU 100%
EU 0%
Engineering Units
Decimal Places
0
0
PID Block Parameters
Out of Service
Auto
Dynamic
Dynamic
FSTATE_TIME
FSTATE_VAL
RCAS_IN
Status
27
AO Block
1
2
3
4
17
18
19
20
21
22
23
24
25
26
27
Value
PV_FTIME
BYPASS
CAS_IN
Status
0
BAD:
NC:
const
0
+INF
+INF
100
Value
SP_RATE_DN
SP_RATE_UP
SP_HI_LIM
SP_LO_LIM
GAIN
RESET
BAL_TIME
RATE
BKCAL_IN
Status
0
1
+INF
0
0
BAD:
NC:
const
0
Value
-Continued-
50
Initial Value
Instruction Manual
D103412X012
August 2012

Index
Number
Parameter Name
Initial Value

Index
Number
Parameter Name
PID Block (continued)

28
29
30
32
33
OUT_HI_LIM
OUT_LO_LIM
BKCAL_HYS
RCAS_IN
Status
100
0
0.5%
BAD:
NoCom:
NoVal:
const
0 Trk
Value
ROUT_IN
Status
BAD:
NoCom:
NoVal:
const
0 Trk
Value
34
37
38
39
40
SHED_OPT
TRK_SCALE
EU 100%
EU 0%
Engineering Units
Decimal places
TRK_IN_D
Status
BAD:
NC:
const
0
Value
TRK_VAL
Status
BAD:
NC:
const
0
Value
FF_VAL
Status
BAD:
NC:
const
0
Value
41
46
FF_SCALE
EU 100%
EU 0%
Engineering Units
Decimal Places
FF_GAIN
ALARM_SUM
DISABLED
ACK_OPTION
47
48
49
50
51
ALARM_HYS
HI_HI_PRI
HI_HI_LIM
HI_PRI
HI_LIM
0.5%
0
+INF
0
+INF
52
53
54
55
LO_PRI
LO_LIM
LO_LO_PRI
LO_LO_LIM
0
-INF
0
-INF
56
57
58
59
DV_HI_PRI
DV_HI_LIM
DV_LO_PRI
DV_LO_LIM
0
+INF
0
-INF
42
45
PID Block (continued)

66
69
70
71
72
73
74
100
0
%
2
0
0
Disabled
BIAS
SP_FTIME
MATHFORM
STRUCTURECONFIG
GAMMA
BETA
IDEABAND
0
0
0
ISEL Block
1
2
3
4
ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
0
spaces
0
0
MODE_BLK
TARGET
PERMITTED
NORMAL
OUT
Out of Service
OOS+MAN+AUTO
Auto
0
100
0
%
2
Initial Value
7
8
10
11
12
OUT_RANGE
EU 100%
EU 0%
Engineering Units
Decimal Places
STATUS_OPTS
IN_1
Status
All off
BAD
NC
cons
0
Value
IN_2
Status
BAD
NC
cons
0
Value
13
14
IN_3
Status
BAD
NC
cons
0
Value
IN_4
Status
BAD
NC
cons
0
Value
15
16
100
0
%
2
DISABLE_1
Status
BAD
NC
cons
0
Value
DISABLE_2
Status
BAD
NC
cons
0
Value
-Continued-
-Continued-
51
Instruction Manual

August 2012
D103412X012

Index
Number
Parameter Name
Initial Value

Index
Number
Parameter Name
ISEL Block (continued)

17
18
DISABLE_3
Status
Value
DISABLE_4
Status
Value
19
20
22
SELECT_TYPE
MIN_GOOD
OP_SELECT
Status
25
26
28
Value
IN_6
Status
30
IN_7
Status
32
Value
IN_8
Status
35
36
37
DISABLE_5
Status
BAD
NC
cons
0
Value
DISABLE_6
Status
BAD
NC
cons
0
DISABLE_7
Status
Value
DISABLE_8
Status
AVG_USE
ALARM_SUM
DISABLED
ACK_OPTION
ALARM_HYS
HI_HI_PRI
All bits: 0
DI Block
1
2
3
4
ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
MODE_BLK
TARGET
PERMITTED
NORMAL
OUT_D
XD_STATE
OUT_STATE
IO_OPTS
STATUS_OPTS
8
10
11
13
14
15
16
20
0
spaces
0
0
Out of Service
OOS+MAN+AUTO
Auto
0
0
All off
All off
21
22
23
CHANNEL
PV_FTIME
ALARM_SUM
DISABLED
ACK_OPTION
DISC_PRI
DISC_LIM
0
0
1
2
3
4
ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
MODE_BLK
TARGET
PERMITTED
NORMAL
SP
OUT_1
OUT_2
OUT_1_RANGE
EU 100%
EU 0%
Engineering Units
Decimal Places
0
All off
0
0
OS Block
7
8
9
10
BAD
NC
cons
0
11
BAD
NC
cons
0
13
14
0
spaces
0
0
OUT_2_RANGE
EU 100%
EU 0%
Engineering Units
Decimal Places
STATUS_OPTS
CAS_IN
Status
100
0
%
2
100
0
%
2
BAD
NC
const
0
Value
0
0
0.5%
0
Out of Service
OOS+MAN+AUTO
AUTO+CAS
disabled
-Continued-
52
LO_LO_LIM
OUT_D
ALM_SEL
BAD
NC
cons
0
Value
33
34
44
49
50
BAD
NC
cons
0
Value
31
BAD
NC
cons
0
BAD
NC
cons
0
Value
29
0
0
0
0
0
0
BAD
NC
cons
0
Value
27
BAD
NC
cons
0
HI_HI_LIM
HI_PRI
HI_LIM
LO_PRI
LO_LIM
LO_LO_PRI
BAD
NC
constant
0
IN_5
Status
ISEL Block (continued)

38
39
40
41
42
43
All off
0
Value
Initial Value
-Continued-
Instruction Manual
D103412X012
August 2012
Table 42. Table Parameters Affected by Restart with

Index
Number
Parameter Name
Initial Value

Index
Number
OS Block (continued)
19
BKCAL_1_IN
Status
Value
20
BKCAL_2_IN
Status
BAD
NC
const
0
0
21
Value
BAL_TIME
1
2
3
4
ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
MODE_BLK
TARGET
PERMITTED
NORMAL
OUT
XD_SCALE
EU at 100%
EU 0%
Units Index
Decimal point
AI Block
8
10
11
13
14
15
16
17
18
22
0
spaces
0
0
Out of Service
OOS, MAN, AUTO
Auto
100
0
%
2
OUT_SCALE
EU 100%
EU 0%
Units Index
Decimal point
I/O OPTS
STATUS OPTS
CHANNEL
L_TYPE
100
0
Trk s/b%
2
disabled
disabled
0
0
0
0
23
24
LOW_CUT
PV_FTIME
ALARM_SUM
DISABLED
ACK_OPTION
ALARM_HYS
25
26
27
28
HI_HI_PRI
HI_HI_LIM
HI_PRI
HI_LIM
0
0
0
0
29
30
31
32
37
38
LO_PRI
LO_LIM
LO_LO_PRI
LO_LO_LIM
OUT_D
ALM_SEL
0
0
0
0
1
2
3
4
7
8
9
10
11
12
13
14
15
MODE_BLK
TARGET
PERMITTED
NORMAL
CHANNEL
OUT_1
OUT_2
OUT_3
OUT_4
OUT_5
OUT_6
OUT_7
OUT_8
1
2
3
4
ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
MODE_BLK
TARGET
PERMITTED
unselected
ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
0
spaces
0
0
Out of Service
OOS, MAN, AUTO
Auto
TB.FINAL_VALUE
TB.TRAVEL_TARGET
TB.FINAL_POSITION_VALUE
TB.TRAVEL
TB.SUPPLY_PRESS
TB.ACT_PRESS_A
TB.ACT_PRESS_B
TB.ACT_PRESS_DIFF
DO Block
0
spaces
0
0
8
9
NORMAL
SP_D
OUT_D
11
12
14
15
PV_STATE
XD_STATE
IO_OPTS
STATUS_OPTS
17
CAS_IN_D
Status
18
19
20
22
0
Disabled
0.5%
MAI Block
Initial Value
MAI Block (continued)

5
BAD
NC
const
0
Parameter Name
23
27
28
Value
CHANNEL
FSTATE_TIME
FSTATE_VAL_D
RCAS_IN_D
Status
Value
SHED_OPT
SP_RATE_UP
SP_RATE_DN
Out of Service
OOS+MAN+AUTO+CAS+
RCAS
AUTO+CAS
0
0
All off
All off
BAD
NC
const
0
22
0
0
BAD
NoComm
NoVal
const
0
All off
0
0
Transducer Block
1
2
3
4
5
87
ST_REV
TAG_DESC
STRATEGY
ALERT_KEY
MODE_BLK
TARGET
PERMITTED
NORMAL
PROTECTION
N/A
NULL
0
1
Out of Service
AUTO, MAN, OOS
Auto
None
-Continued-
53
Instruction Manual

August 2012
D103412X012
Resource Block Parameter List

Read/Write Capability: RO - Read Only, RW - Read Write
Mode: The block mode(s) required to write to the parameter
Double indentation and shaded Index Number indicates subparameter.
Table 43. Resource Block Parameter Definitions
Label
PARAMETER_NAME
Index
Number
RO /
RW
Mode
Range
Initial
Value
Description
Static Revision
ST_REV
RO
NA
0 to 65535
Data Type: Unsigned16

The revision level of the static data. Increments
by one each time a static parameter changes.
The value is reset to 0 whenever a Restart with
Defaults is performed. See Restarting the
Instrument.
Tag Description
TAG_DESC
RW
NA
7 bit ASCII
Spaces
Data Type: Octet String

The user description of the intended application
of the block. Null characters are not allowed in
this data type.
Strategy
STRATEGY
RW
ALL
0 to 65535

Used to identify groupings of blocks. The data is
not checked or processed by the block.

The identification number of the plant unit.
Devices in a loop or plant section can be
assigned with a common alert key to aid the
operator in determining location of alerts.
Alert Key
ALERT_KEY
Block Mode
MODE_BLK
TARGET_MODE
5.1
RW
ALL
1 to 255
RW
ALL
3: Auto
7: OOS
3: Auto
N/A
ACTUAL_MODE
5.2
RO
NA
3: Auto
6: IMAN (only during
initialization
7: OOS
PERMITTED_MODE
5.3
RW
ALL
3: Auto
7: OOS
3: Auto
7: OOS
NORMAL_MODE
5.4
RW
ALL
3: Auto
3: Auto
N/A
0: Other
1: Block Configuration
Error
3:Simulate Active
6:Device needs
Maintenance Soon
9:Memory Failure
10:Lost Static Data
11:Lost NonVolatile
Memory
13:Device needs
Maintenance Now
14:Powerup
15:Outof
Service (MSB)
N/A
2:Initialization,
Actual mode=IMAN
4:Online, Actual
Mode=Auto
5:Standby, Actual
Mode=OOS
6:Failure, Actual
Mode=OOS
Block Error
BLOCK_ERR
Device State
RS_STATE
Test Read Write

TEST_RW
RO
RO
ALL
5: Standby
-Continued-
54
Dynamic
Data Type: DS69

The actual, target, permitted, and normal
modes.
Target: The requested block mode
Actual: The current mode of the block
Permitted: Allowed modes for Target
Normal: Most common mode for Target
Data Type: Bit String

0 = Inactive
1 = Active
Error status associated with hardware or
software for the resource block. When an error is
shown it may be broadcast to the host through
BLOCK_ALM.

State of the function block application state
machine.
This parameter may be used in interoperability

testing to read and write all standard data types
supported by the Fieldbus Foundation.
Instruction Manual
D103412X012
August 2012
Table 43. Resource Block Parameter Definitions (Continued)

Label
PARAMETER_NAME
DD Resource
DD_RESOURCE
Index
Number
RO /
RW
Mode
RO
N/A
Range
Initial
Value
Description
Spaces
Data Type: Visible String

String identifying the VFD tag of the resource
that contains the Device Description for this
resource.
Manufacturer Id
MANUFAC_ID
10
RO
N/A
0x5100

Manufacturer identification number, used by an
interface device or host to locate the DD file for
the resource. All manufacturer identification
numbers are maintained by the Fieldbus
Foundation. A host usually will have a base
directory for DD files. In this directory is a
subdirectory for each manufacturer id. In each
manufacturer id subdirectory is a directory for
each device type made by that manufacturer.
The device type directories contain files named
by combining the device revision for the
particular device type with the revision of the
device description. The manufacturer id for
Fisher is 0x005100.
Device Type
DEV_TYPE
11
RO
N/A
4602

Manufacturer's model number associated with
the resource, used by an interface device to
locate the DD file for the resource.
N/A
Varies with
release

Manufacturer's revision number associated with
the resource, used by an interface device to
locate the DD file for the resource.
Varies with
release

The minimum revision of the device description
(DD) than can be used with the device revision
of the instrument. Used by the interface device
to prevent the use of DDs that are incompatible
with the firmware in the instrument.
Device Revision
DEV_REV
12
DD Revision
DD_REV
13
Grant Deny
GRANT_DENY
14
RO
RO
N/A
GRANT
14.1
RW
ALL
DENY
14.2
RW
ALL
Hard Types
HARD_TYPES
Restart
RESTART
Features
FEATURES
15
16
17
RO
RW
RO
Valid Bits:
0: Program
1: Tune
2: Alarm
3: Local
N/A
0: Scalar Input
1: Scalar Output
2: Discrete Input
3: Discrete Output
ALL
1=Run
2=Restart resource
3=Restart with
defaults
4=Restart processor
ALL
1:Reports supported
2:Fault State
supported
3:Software Write
lock supported
10:Reannunciation
supported
All bits: 0
All bits: 0
Data Type: DS70

Options for controlling access of a host
computer and to block parameters. Parameter
contains two attributes Grant and Deny each
with program, tune, alarm and local
permissions. Clearing a grant permission sets
the corresponding deny permission, 0 = N/A, 1 =
granted.
Deny permissions may be cleared through the
Deny attribute but not set, 0 = N/A, 1 = denied.
0: 1
1: 1
2: 1
3: 1

0 = Inactive
1 = Active
The types of hardware available as channel
numbers in this resource.
1=Run

Allows a manual restart to be initiated. For
details see Restarting the Instrument in this
section.
1: 1
2: 1
3: 1
10: 1

0 = Inactive
1 = Active
Shows the supported resource block options.
Options are turned on and off via
FEATURE_SELECT.
-Continued-
55
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Features Selected
FEATURE_SEL
Cycle Type
CYCLE_TYPE
Cycle Selection
CYCLE_SEL
Minimum Cycle Time

MIN_CYCLE_T
Memory Size
MEMORY_SIZE
Nonvolatile Cycle Time

NV_CYCLE_T
Free Space
FREE_SPACE
Free Time
FREE_TIME
RCAS Timeout
SHED_RCAS
Index
Number
18
19
RO /
RW
RW
RO
20
21
22
23
24
25
26
Mode
Range
Initial
Value
ALL
1: Reports Supported
2: Fault State
supported
3: Software Write lock
supported
10:Reannunciation
supported
1:0
2:1
3:1
10:0

0 = Inactive
1 = Active
Shows the selected resource block options. For
details see Device Features in this section.
0: 1

0 = Inactive
1 = Active
Identifies the block execution methods available
for this resource, may be scheduled, completion
of block execution
0: 0

0 = Inactive
1 = Active
Identifies the block execution method selected
for this resource.
3200

Time duration of the shortest cycle interval (in
1/32 millisecond) of which the resource is
capable. In the digital valve controller this value
is fixed at 3200 (100 milliseconds).
45
Date Type: Unsigned16

Memory, in kilobytes, available for additional
function blocks. Because no additional function
blocks may be added to DVC6200f instruments,
this parameter value is fixed at 45.
576,000

This parameter identifies the minimum time
interval (in 1/32 milliseconds) between copies of
NV class data to NV memory. NV memory is
updated only if there has been a change in the
dynamic value. The last value saved in NV
memory will be available for the restart
procedure or a power cycle. A nonzero value
regulates the frequency of writes, thus
protecting the life span of the device. If the value
is zero, data will never be automatically copied.
Changes made by other than publishing to NV
parameters will be copied to nonvolatile
memory immediately. For DVC6200f
instruments, this parameter value is fixed at
576,000 (18 seconds).
Data Type: Float

Percent of memory available for additional
function blocks (see also MEMORY_SIZE).
Because no additional function blocks may be
added to DVC6200f instruments, this parameter
value is fixed at 0.
Data Type: Float

Percent of block processing time that is free to
process additional blocks. Because no additional
function blocks may be added to DVC6200f
instruments, this parameter value is fixed at 0.
640000

Time duration (in 1/32 millisecond) at which to
give up on computer writes to function block
RCAS parameters. If this time is exceeded then
the function block will change to a mode other
than RCAS based on the SHED_OPT parameter
setting. Shed from RCAS mode never happens
when SHED_RCAS is set to zero.
NA
ALL
RO
RO
RO
RO
RO
RW
NA
NA
NA
NA
NA
ALL
0: Scheduled
0: Scheduled
3200
45
Positive
0 to 100%
0 to 100%
Positive
-Continued-
56
Description
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
ROUT Timeout
SHED_ROUT
Fault State
FAULT_STATE
Set Fault State

SET_FSTATE
Clear Fault State

CLR_FSTATE
Maximum Notify
MAX_NOTIFY
Index
Number
27
28
29
30
31
RO /
RW
RW
RO
RW
RW
RO
Mode
ALL
N/A
ALL
ALL
N/A
Range
Positive
1=Clear
2=Active
1=Off
2=Set
1=Off
2= Clear
Maximum Alerts Allow

LIM_NOTIFY
32
RW
ALL
0 to MAX_NOTIFY
Confirm Time
CONFIRM_TIME
33
RW
ALL
> 0
Set by FCS
Initial
Value
Description
640000

Time duration (in 1/32 millisecond) at which to
give up on computer writes to function block
ROUT parameters. If this time is exceeded then
the function block will change to a mode other
than ROUT based on the SHED_OPT parameter
setting. Shed from ROUT mode never happens
when SHED_ROUT is set to zero.
1=Clear

Forces output function blocks that are not Out
of Service to the fault state condition. While this
parameter is active the output function blocks
will go to an actual mode of Local Override (LO)
and will perform their fault state actions (see
Action On Fault Detection for the output blocks
on pages 118 and 194 of this section). This
parameter is used to test the fault state behavior
that normally occurs when there is a
communication problem between devices. This
parameter is changed by the SET_FSTATE and
CLR_FSTATE parameters so long as the feature
Fault State is selected (see Feature Selection
[index number 18] in this table).
1=Off

Selecting Set changes the parameter
FAULT_STATE to Active. This is essentially a
write only parameter as it will always read OFF
because it is defined as momentary. Writing a
value of OFF has no affect. To use this parameter
the feature Fault State must be selected (see
Features Selected on page 47).
1=Off

Selecting Clear changes the parameter
FAULT_STATE to Clear and clears the output
function blocks of the FAULT_STATE if the field
condition, if any, has cleared. This is essentially a
write only parameter as it will always read OFF
because it is defined as momentary. Writing a
value of OFF has no affect. To use this parameter
the feature Fault State must be selected (see
Features Selected on page 47.

The maximum number of alert reports that this
device can send without getting a confirmation.
To control alert flooding, the number can be set
lower by adjusting the LIM_NOTIFY parameter
value. For DVC6200f instruments, this value is
fixed at 3.
MAX_NOTIFY

The number of alert reports that this device can
send without getting a confirmation up to the
maximum permitted in the parameter
MAX_NOTIFY. If set to zero, then no alerts are
reported.
640000

The time (in 1/32 millisecond) the device waits
for confirmation of receipt of an alert report
before trying again.
-Continued-
57
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Index
Number
Write Lock
WRITE_LOCK
34
Update Event
UPDATE_EVT
35
RO /
RW
Mode
Range
Description
If set to Locked, no writes from anywhere are
allowed except to clear WRITE_LOCK by entering
Unlocked. Block inputs will continue to be
updated if they are subscribers. The feature Soft
Write Lock must be selected to enable writing to
this parameter (see Device Features in this
section).
RW
ALL
0=Undefined
1=Unlocked
2=Locked
1=Unlocked
UNACKNOWLEDGED
35.1
RW
ALL
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
UPDATE_STATE
35.2
RO
NA
0=Undefined
1=Update reported
2=Update not
reported
0=Undefined
TIME_STAMP
35.3
RO
NA
STATIC_REVISION
35.4
RO
NA
RELATIVE_INDEX
35.5
RO
NA
RW
ALL
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
0=Undefined
1=Clear reported
2=Clear not reported
3=Active reported
4=Active not reported
0=Undefined
Block Alarm
BLOCK_ALM
UNACKNOWLEDGED
36.1
36.2
RO
NA
TIME_STAMP
36.3
RO
NA
SUBCODE
36.4
RO
NA
VALUE
36.5
RO
NA
RO
NA
0: Discrete alarm
7: Block Alarm
All bits: 0
NA
0: Discrete alarm
7: Block Alarm
All bits: 0
All bits: 0
CURRENT
UNACKNOWLEDGED
Data Type: DS73

This alert is generated by any change to the
static data. To support tracking changes in static
parameter values, the blocks static revision
parameter will be incremented each time a
static parameter value is changed. Also, the
blocks static revision parameter may be
incremented if a static parameter is written but
the value is not changed. If the Actual Mode is
not Out of Service and Reports is selected in the
Feature Select parameter, then this parameter
will be sent to the host system providing the
host has set up alert communications. Changes
to static data while the block is Out of Service
will be reported when the block transitions to
another mode.
36
ALARM_STATE
Alarm Summary
ALARM_SUM
Data Type: DS72

This alarm is generated by a nonzero value in the
Block Error. parameter. This alarm has a fixed
priority of 2. For a BLOCK_ALM to be broadcast
to the host the following conditions must be
met:
The feature Reports must be selected
Alert communication with the host must be
setup
In the ALARM_SUM parameter, the disable bit
for Block Alarm must be clear.
37
37.1
37.2
RO
UNREPORTED
37.3
RO
NA
0: Discrete alarm
7: Block Alarm
DISABLED
37.4
RW
ALL
0: Discrete alarm
7: Block Alarm
All bits: 0
0: 0
7: 0
Acknowledge Option
ACK_OPTION
38
RW
ALL
0: Discrete Alarm
(Write Lock off)
7: Block Alarm
Write Priority
WRITE_PRI
39
RW
ALL
0 to 15
-Continued-
58
Initial
Value
Data Type: DS74

0=clear, acknowledged, reported, enabled
Current alert status, unacknowledged states,
unreported states, and disabled states of the
alarms associated with the function block. The
Resource block only has two alarms: Write Alarm
and Block Alarm.
0=Disable
1=Enable
Selection of whether alarms associated with the
block will be automatically acknowledged.
Priority of the alarm generated by setting
WRITE_LOCK to Unlocked.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Write Alarm
WRITE_ALM
UNACKNOWLEDGED
Index
Number
RO /
RW
Mode
Range
Initial
Value
40
40.1
RW
ALL
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
0=Undefined
1=Clear reported
3=Active reported
0=Undefined
ALARM_STATE
40.2
RO
NA
TIME_STAMP
40.3
RO
NA
SUBCODE
40.4
RO
NA
VALUE
40.5
RO
NA
ITK Version
ITK_VER
41
RO
N/A
Private Label Distributor

DISTRIBUTOR
42
RO
NA
Device String Array

DEV_STRING
43
Description
Data Type: DS72
This alarm is generated when Unlocked in the
WRITE_LOCK parameter is set. This alarm has a
priority of WRITE_PRI. For a WRITE_ALM to be
broadcast to the host the following conditions
must be met:
The feature Reports must be selected
Alert communication with the host must be
setup
In the ALARM_SUM parameter, the disable bit
for Write Alarm must be clear.
WRITE_PRI must be greater than 1.
Major version of ITK test this device has been
tested to. *Initial value depends on the revision
of the DVC6200f.
Extended Parameters

FB_OPTIONS
Diagnostic Options
DIAG_OPTIONS
44
45
MISC_OPTIONS
46
Firmware Revision
FIRMWARE_REVISION
47
0x5100
Unused extended parameter.
RO
Bits
0: AO
1: DO
2: AI
3: DI
4: PID
5: ISEL
6: OS
7: MAI
RO
NA
1=FD Fieldbus
Diagnostics
2=AD Advanced
Diagnostics
3=PD Performance
Diagnostics
RO
NA
0: Software Download
10: Travel Control
Capable
11: Pressure Control
Capable
12: Fallback Capable
All options
enabled

0=disabled
1=enabled
Indicates which function block licensing options
are enabled. One bit for each block type that is
supported. Unlicensed blocks cannot be
scheduled and the Actual block mode will
remain OOS.
Data Type: Enum

Indicates which diagnostics licensing options are
enabled. *Initial value depends on the licensed
DVC6200f options.
FD
0: 1
10: 1
11: 1
AD/PD
0: 1
10: 1
11: 1
12: 1
FIRMWARE_REV_MAJOR
47.1
RO
NA
0-255
FIRMWARE_REV_MINOR
47.2
RO
NA
0-255
FIRMWARE_REV_BUILD
47.3
RO
NA
0-255
IO_FIRMWARE_REV
47.4
RO
NA
0-255
DIAG_CAL_REV
47.5
RO
NA
0-255
FIRMWARE_REV_ALL
Hardware Revision
HARDWARE_REV

Private label distributor
47.6
RO
NA
XX.XX.XX
48
RO
NA
Hardware revision
number
Factory Set

0=Disable
1=Enable
Indicates which miscellaneous licensing options
are enabled.
Data Type: Uint8

Describes software revision information. This is
the revision of the firmware that is currently in
use.
*Initial value depends on revision of DVC6200f.
Describes software revision information.
The range of this parameter consists of 47.1
through 47.5 values, converted to text, and
linked together.
*Initial value depends on revision of DVC6200f
Data Type: Uint8
Describe electronic hardware revision
information.
-Continued-
59
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Index
Number
RO /
RW
Mode
Electronics Serial Number

ELECTRONICS_SN
49
RO
NA
NA
Factory Set
Factory Serial Number

FACTORY_SN
50
RO
NA
NA
spaces

Instrument serial number set by manufacturing.
Field Serial Number

FIELD_SN
51
RW
NA
Any String
spaces

Instrument serial number set in the field.
Detailed Status
DETAILED_STATUS
52
RO
NA
NA
Time Since Reset

TIME_SINCE_RESET
53
RO
NA
NA
Device ID
DEVICE ID
54
RO
NA
NA
Device ID
STBY_FIRMWARE_REV
Initial
Value
55.1
RO
NA
0-255
STBY_FIRMWARE_REV_MINOR
55.2
RO
NA
0-255
STBY_FIRMWARE_REV_BUILD
55.3
RO
NA
0-255
STBY_IO_FIRMWARE_REV
55.4
RO
NA
0-255
STBY_DIAG_CAL_REV
55.5
RO
NA
0-255
FB_AVAILABLE
Description
Data Type: Visible String Electronics serial
number set by manufacturing.
Data Type: Uint32

Not used
Number of seconds since the last time
DVC6200f was restarted. Restart due to power
up or restart command.
Unique 32 character ID used to identify the
device.
55
STBY_FIRMWARE_REV_MAJOR
STBY_FIRMWARE_REV_ALL
60
Range
55.6
56
RO
RO
NA
XX.XX.XX
NA
Bits
0: AO
1: DO
2: AI
3: DI
4: PID
5: ISEL
6: OS
7: MAI
NA
All options
enabled
Data Type: Uint8

Describes firmware revision information. This is
the revision of the alternative firmware.
*Initial value depends on revision of firmware in
standby.
Describes firmware revision information.
*Initial value depends on revision of firmware in
standby. The range of this parameter consists of
55.1 through 55.5 values, converted to text, and
linked together.

0=disabled
1=enabled
Indicates which function blocks are included in
the device.
Instruction Manual
D103412X012
August 2012
View Lists
View lists allow the values of a set of parameters to be accessed at the same time. Views 1 and 2 contain operating
parameters and are defined by the Fieldbus Foundation. View 3 contains dynamic parameters and View 4 contains
static parameters with configuration and maintenance information. Views 3 and 4 are defined by the manufacturer.
Table 44. Resource Block, View 1
Index Number
1
Parameter
ST_REV
5.1
MODE_BLK.TARGET_MODE
5.2
MODE_BLK.ACTUAL_MODE
5.3
MODE_BLK.PERMITTED_MODE
5.4
MODE_BLK.NORMAL_MODE
BLOCK_ERR
RS_STATE
25
FREE_TIME
28
FAULT_STATE
ALARM_SUM.CURRENT
37.2
ALARM_SUM.UNACKNOWLEDGED
37.3
ALARM_SUM.UNREPORTED
37.4
ALARM_SUM.DISABLED

1
Parameter
ST_REV
14.1
GRANT_DENY.GRANT
14.2
GRANT_DENY.DENY
18
FEATURE_SEL
20
CYCLE_SEL
23
NV_CYCLE_T
24
FREE_SPACE
26
SHED_RCAS
27
SHED_ROUT
32
LIM_NOTIFY
33
CONFIRM_TIME
34
WRITE_LOCK
Index Number
37.4
Parameter
ALARM_SUM.DISABLED
44
FB_OPTIONS
52
DETAILED_STATUS
53
TIME_SINCE_RESET
54
DEVICE_ID
37.1
Index Number
Table 46. Resource Block, View 3 (continued)
Index
Number
Parameter
ST_REV
STRATEGY
ALERT_KEY
10
MANUFAC_ID
11
DEV_TYPE
12
DEV_REV
13
DD_REV
15
HARD_TYPES
17
FEATURES
19
CYCLE_TYPE
21
MIN_CYCLE_T
22
MEMORY_SIZE
31
MAX_NOTIFY
38
ACK_OPTION
39
WRITE_PRI
41
ITK_VER
42
DISTRIBUTOR
43
DEV_STRING
45
DIAG_OPTIONS
46
MISC_OPTIONS
47.1
FIRMWARE_REVISION.FIRMWARE_REV_MAJOR
47.2
FIRMWARE_REVISION.FIRMWARE_REV_MINOR
47.3
FIRMWARE_REVISION.FIRMWARE_REV_BUILD
ST_REV
47.4
FIRMWARE_REVISION.IO_FIRMWARE_REV
5.1
47.5
FIRMWARE_REVISION.DIAG_CAL_REV
5.2
47.6
FIRMWARE_REVISION.FIRMWARE_REV_ALL
5.3
48
HARDWARE_REV
5.4
49
ELECTRONICS_SN
BLOCK_ERR
50
FACTORY_SN
RS_STATE
51
FIELD_SN
25
FREE_TIME
55.1
STBY_FIRMWARE_REV.STBY_FIRMWARE_REV_MAJOR
28
FAULT_STATE
55.2
STBY_FIRMWARE_REV.STBY_FIRMWARE_REV_MINOR
37.1
ALARM_SUM.CURRENT
55.3
STBY_FIRMWARE_REV.STBY_FIRMWARE_REV_BUILD
37.2
55.4
STBY_FIRMWARE_REV.STBY_IO_FIRMWARE_REV
37.3
55.5
STBY_FIRMWARE_REV.STBY_DIAG_CAL_REV
55.6
STBY_FIRMWARE_REV.STBY_FIRMWARE_REV_ALL

Index Number
1
Parameter
-continued-
61
Detailed SetupTransducer Block

August 2012
Instruction Manual
D103412X012
Transducer Block
Overview
The transducer block accepts a signal from an output block as a set point to position a valve using a pneumatic
actuator. Input to the transducer block is in percent. Closed is 0%, and open is 100%. The transducer block contains
setup and calibration information and can be tuned to closely match the actuator. Input characterization permits
modifying the overall characteristic of the instrumentactuatorvalve combination in order to modify the installed gain
characteristic of the loop. The transducer block can also be used to perform instrument and valve diagnostics and
trigger performance alerts.
The following procedures address only the key transducer block parameters; however, all transducer block parameters
are listed in table 414.
Detailed Setup
Note
To setup and calibrate the instrument, the transducer block Mode must be Manual and the Protection must be None.

Field Communicator
TB > Configure/Setup > Detailed Setup > Transducer Block Mode
Modes
The transducer block can be in one of three modes (MODE_BLK [5]):
Automatic (Auto) This is the normal mode for this block. When the transducer block is in the auto mode, it accepts
the output from the AO or DO block as a set point and outputs a drive signal to the I/P converter based upon this set
point.
Out of Service (OOS) Placing the transducer block in Out of Service mode changes the output to the zero power
(no I/P drive) condition.
Field Communicator
Manual (MAN) Placing the transducer block in Manual will hold the value at the current setpoint (FINAL_VALUE
[13]). The transducer block will not accept changes from the AO or DO blocks. This mode is required to change some
parameters and to run some diagnostics.
Protection
Field Communicator
TB > Configure/Setup > Detailed Setup > Protection
To configure any parameters in the digital valve controller Write Lock (WRITE_LOCK [34]), in the resource block, must
be set to Unlocked (refer to page 45). In addition, protection is provided for various transducer block parameters, as
62
Instruction Manual
D103412X012
August 2012
indicated in the Protect Category column of table 414, to prevent inadvertently overwriting key data by the host
system or user.
All will protect all transducer block Parameters.
Setup and Calibration will protect only Setup and Calibration transducer block parameters.
Calibration will protect only Calibration transducer block parameters.
None will not protect any transducer block parameters.
Note
The Device Setup Auto Travel and Manual Travel methods automatically change transducer block protection for the user.
See table 414 for individual parameter details.
Response Control
Travel Tuning
Field Communicator
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning
WARNING
Travel Tuning SetThere are eleven Travel Tuning Sets (TVL_TUNING_SET [42.10]) to choose from. Each tuning set
provides a preselected value for the digital valve controller gain settings.
Tuning set C provides the slowest response and M provides the fastest response. Table 48 lists the proportional gain,
velocity gain and minor loop feedback gain values for preselected tuning sets.
In addition, you can specify Expert tuning and individually set the proportional gain, velocity gain, and minor loop
feedback gain. Individually setting or changing any tuning parameter or running the Performance Tuner or
Stabilize/Optimize will automatically change the tuning set to X (expert).
Table 48. Gain Values for Preselected Travel Tuning Sets
Tuning Set
Travel Velocity Gain
Travel Minor Loop Feedback Gain
C
D
E
F
G
Travel Proportional Gain

4.4
4.8
5.5
6.2
7.2
3.0
3.0
3.0
3.1
3.6
35
35
35
35
34
H
I
J
K
L
M
X (Expert)
8.4
9.7
11.3
13.1
15.5
18.0
User Adjusted
4.2
4.8
5.6
6.0
6.0
6.0
User Adjusted
31
27
23
18
12
12
User Adjusted
Note
Use Expert tuning if standard tuning has not achieved the desired results.
63

August 2012
Instruction Manual
D103412X012
Stabilize/Optimize may be used to achieve the desired results more rapidly than Expert tuning.
Table 32 provides tuning set selection guidelines for Fisher and Baumann actuators. These tuning sets are
recommended starting points. After you finish setting up and calibrating the instrument, you may have to select either
a higher or lower tuning set to get the desired response.
For an actuator not listed in table 32, you can estimate a starting tuning set by calculating the casing or cylinder
volume. Then, find an actuator in table 32 with the closest equivalent volume and use the tuning set suggested for
that actuator.
Travel Proportional GainTravel Proportional Gain (SERVO_GAIN [18]) is the proportional gain for the travel control
tuning set. Changing this parameter will also change the tuning set to Expert.
Travel Velocity GainTravel Velocity Gain (SERVO_RATE [20]) is the velocity gain for the travel control tuning set.
Changing this parameter will also change the tuning set to Expert.
Travel MLFB GainTravel MLFB Gain (TVL_MLFB_GAIN [44.5]) is the minor loop feedback gain for the travel control
tuning set. Changing this parameter will also change the tuning set to Expert.
Travel Integral EnableTravel Integral Enable (TVL_INTEG_ENABLE [44.1]) is used to enable the integral setting to
improve static performance by correcting for error that exists between the travel target and actual travel.
Travel Integral GainTravel Integral Gain (SERVO_RESET [19]) (also called reset) is the ratio of the change in output
to the change in input, based on the control action in which the output is proportional to the time integral of the
input.
Travel Integral Dead ZoneTravel Integral Dead Zone (TVL_INTEG_DEADZ [44.4]) is a window around the Primary
Setpoint in which the integral action is disabled. The dead band is configurable from 0 to 2%.
Travel Integral Limit HiTravel Integral Limit Hi (TVL_INTEG_LIM_HI [44.2]) provides an upper limit to the integrator
output. The high limit is configurable from 0 to 100% of the I/P drive signal.
Travel Integral Limit LoThe Travel Integral Limit Lo (TVL_INTEG_LIM_LO [44.3]) provides a lower limit to the
integrator output. The low limit is configurable from -100 to 0% of the I/P drive signal.
Performance Tuner
WARNING
During performance tuning the valve may move, causing process fluid or pressure to be released. To avoid personal injury
Performance Tuner is used to determine digital valve controller tuning. It will move the valve slightly and monitor the
effects of small tuning changes until an optimum control response is achieved. Because the Performance Tuner can
detect internal instabilities before they become apparent in the travel response, it can generally optimize tuning more
effectively than manual tuning.
Stabilize/Optimize
WARNING
During Stabilize/Optimize the valve may move, causing process fluid or pressure to be released. To avoid personal injury
64
Instruction Manual
D103412X012

August 2012
If after completing initial setup and calibration the valve cycles or overshoots, or is sluggish, you can improve
operation by running Stabilize/Optimize.
Stabilize/Optimize is included with the device description (DD) firmware. Stabilize/Optimize is accessible from the
transducer block and permits changing the transducer block set point a small amount to see if the valve is unstable or
unresponsive. If valve response is unsatisfactory, the method permits adjusting the digital valve controller tuning to
improve response.
If the valve is unstable, select Decrease Response to stabilize valve operation. This selects the next lower tuning set
(e.g., F to E). If the valve response is sluggish, select Increase Response to make the valve more responsive. This selects
the next higher tuning set (e.g., F to G).
If after selecting Decrease Response or Increase Response the valve travel overshoot is excessive, Increase Damping or
Decrease Damping can be used to select a damping value not represented in a predefined tuning set. Select Decrease
Damping to select a damping value that allows more overshoot. Select Increase Damping to select a damping value that
will decrease the overshoot.
When valve operation is satisfactory, select Exit. Before exiting, you are asked if you want to return the transducer
block mode to Auto. Select Yes to change the transducer block mode to Auto. Select No to leave the transducer block
in its current mode.
Pressure Tuning
Field Communicator
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning
WARNING
Pressure Tuning Set

There are twelve Pressure Tuning Sets (PRESS_TUNING_SET [42.11]) to choose from. Each tuning set provides a
preselected value for the digital valve controller gain settings.
Tuning set C provides the slowest response and M provides the fastest response. Tuning set B is appropriate for
controlling a pneumatic positioner. Table 49 lists the proportional gain, pressure integrator gain and minor loop
feedback gain values for preselected tuning sets.
In addition, you can specify Expert tuning and individually set the pressure proportional gain, pressure integrator gain,
and pressure minor loop feedback gain. Individually setting or changing any tuning parameter will automatically
change the tuning set to X (expert).
65
Instruction Manual

August 2012
D103412X012
Table 49. Gain Values for Preselected Pressure Tuning Sets

Tuning Set
B
C
D
E
F
G
H
I
J
K
L
M
X (Expert)
Pressure Proportional Gain

0.5
2.2
2.4
2.8
3.1
3.6
4.2
4.8
5.6
6.6
7.8
9.0
User Adjusted
Pressure Integrator Gain
Pressure Minor Loop Feedback Gain
0.3
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
User Adjusted
35
35
35
35
35
34
31
27
23
18
12
12
User Adjusted
Note
Use Expert tuning only if standard tuning has not achieved the desired results.
Stabilize/Optimize may be used to achieve the desired results more rapidly than Expert tuning.
Pressure Proportional GainPressure Proportional Gain (PRESS_PROP_GAIN [47.3]) is the proportional gain for the
pressure control tuning set. Changing this parameter will also change the tuning set to Expert.
Pressure MLFB GainPressure MLFB Gain (PRESS_MLFB_GAIN [47.11]) is the minor loop feedback gain for the
pressure control tuning set. Changing this parameter will also change the tuning set to Expert.
Pressure Integral GainPressure Integral Gain (PRESS_INTEG_GAIN [47.4]) (also called reset) is the ratio of the
change in output to the change in input, based on the control action in which the output is proportional to the time
integral of the input. Changing this parameter will also change the tuning set to Expert.
Pressure Integral Dead ZonePressure Integral Dead Zone (PRESS_INTEG_DEADZ [47.6]) is a window around the
Primary Setpoint in which the integral action is disabled. The dead band is configurable from 0 to 2%.
Pressure Integral Limit HiPressure Integral Limit Hi (PRESS_INTEG_HI_LIM [47.7]) provides an upper limit to the
integrator output. The high limit is configurable from 0 to 100% of the I/P drive signal.
Pressure Integral Limit LoPressure Integral Limit Lo (PRESS_INTEG_LO_LIM [47.8]) provides a lower limit to the
integrator output. The low limit is configurable from -100 to 0% of the I/P drive signal.
Travel Pressure Control

Field Communicator
TB > Configure/Setup > Detailed Setup > Response Control > Travel Pressure Control
Travel/Pressure StateTravel/Pressure State (TVL_PRESS.STATE [41.2]) indicates if the instrument is being used for
travel control (position control) or as an I/P (pressure control)
Travel/Pressure Select
CAUTION
When using Pressure Fallback Manual Recovery or Pressure Fallback Auto Recovery, the valve travel has the potential of
moving rapidly causing potential process instability when returning to Travel Control.
66
Instruction Manual
D103412X012
August 2012
Note
Travel / Pressure Select must be set to Travel for double acting actuators.
Travel / Pressure Select (TVL_PRESS_SELECT [41.1]) determines if the instrument is setup for position or pressure
control. Select Travel, Pressure, Travel with Pressure Fallback/Auto recovery or Travel with Pressure Fallback/Manual
Recovery. If the travel sensor fails, and Travel with Pressure Fallback/Auto Recovery is selected, it will return to travel
control when the travel sensor starts working again. Travel with Pressure Fallback/Manual recovery will stay in pressure
control until Travel Pressure Select is changed to Travel or Travel with Pressure Fallback/Auto recovery. It is not
necessary to enable the Travel Sensor Alert for Pressure Fallback to occur.
Travel Deviation Pressure FallbackTravel Deviation Pressure Fallback occurs when the instrument detects that the
travel sensor is outside of its normal range of operation or that a gross deviation exists between set point and actual
travel. It switches to Pressure Control and no longer uses the travel sensor to position the valve.
Travel Cutoff HiTravel Cutoff Hi (FINAL_VALUE_CUTOFF_HI [15]) defines the high cutoff point for the travel in
percent (%) of precharacterized setpoint. Above this cutoff, the travel target is set to 123.0% of the ranged travel.
Travel Cutoff Hi is deactivated by setting it to 125.0%.
Travel Cutoff LoTravel Cutoff Lo (FINAL_VALUE_CUTOFF_LO [16]) defines the low cutoff point for the travel in
percent (%) of precharacterized setpoint. Below this cutoff, the travel target is set to -23%. A Travel Cutoff Lo of
0.5% is recommended to help ensure maximum shutoff seat loading. Travel Cutoff Lo is deactivated by setting it to
-25.0%
Pressure Cutoff OpenPressure Cutoff Open (PRESS_CUTOFF_HI [47.1]) defines the high cutoff point for the
pressure in percent (%) of precharacterized setpoint. Above this cutoff, the pressure target is set to 123.0%. A
Pressure Cutoff Open of 99.5% is recommended to ensure valve goes fully open. Pressure Cutoff Hi is deactivated by
setting it 125%.
Pressure Cutoff ClosedPressure Cutoff Closed (PRESS_CUTOFF_LO [47.2]) defines the low cutoff point for the
pressure in percent (%) of precharacterized setpoint. Below this cutoff, the pressure target is set to -23%. A Pressure
Cutoff Closed of 0.5% is recommended to help ensure maximum shutoff seat loading. Pressure Cutoff Closed is
deactivated by setting it to -25.0%
Pressure Range HiPressure Range Hi (PRESS_RANGE_HI [42.7]) is the high end of output pressure range. Enter the
pressure that corresponds with 100% valve travel when Zero Power Condition is closed, or 0% valve travel when
Zero Power Condition is open. This pressure must be greater than the Pressure Range Lo.
Pressure Range LoPressure Range Lo (PRESS_RANGE_LO [42.8]) is the low end of the output pressure range. Enter
the pressure that corresponds to 0% valve travel when Zero Power Condition is closed, or 100% valve travel when
Zero Power Condition is open. The pressure must be less than the Pressure Range Hi.
Field Communicator
TB > Configure/Setup > Detailed Setup > Response Control > Input Characterization
Input Characterization (INPUT_CHAR [50]) defines the relationship between the travel target and the setpoint
received from the output block. Travel target is the output from the characterization function.
67
Instruction Manual

August 2012
D103412X012
Custom Characterization Table

TB > Configure/Setup > Detailed Setup > Response Control > Custom Characterization Table
Field Communicator
You can select from the three fixed input characteristics shown in figure 41 or you can select a custom characteristic.
Figure 41 shows the relationship between the travel target and travel set point for the fixed input characteristics.
You can specify 21 points on a custom characteristic curve. Each point defines a travel target, in % of ranged travel, for
a corresponding set point, in % of ranged set point. Set point values range from -25.0% to 125%. Before modification,
the custom characteristic is linear. You cannot modify the custom points if the Input Characterization (INPUT_CHAR
[50]) is set to custom.
Figure 41. Travel Target Versus Ranged Set Point, for Various Input Characteristics (Zero Power Condition = Closed)
125
100
100
Travel Target, %
Travel Target, %
125
-25
-25
-25
Set Point, %
100
125
-25
Set Point, %
Input Characteristic Linear

125
Travel Target, %
100
-25
-25
A65351
68
100
Input Characteristic Equal Percentage
Set Point, %
100
Input Characteristic Quick Opening
125
125
Instruction Manual
D103412X012
August 2012
Outblock Selection
Field Communicator
TB > Configure/Setup > Detailed Setup > Response Control > Outblock Selection
Outblock Selection (OUTBLOCK_SEL [96]) defines which output function block will control the setpoint of the valve.
The output block that is not selected will shed its mode to reflect that it does not have control of the valve.
Alerts
The DVC6200f provides two levels of alerts; Instrument alerts and PlantWeb alerts.
Instrument Alert Conditions

Instrument Alert Conditions, when enabled, detect many operational and performance issues that may be of interest.
To view these alerts, the user must open the appropriate status screen on a host such as DeltaV, ValveLink software or
a Field Communicator.
PlantWeb Alerts
Some instrument alert conditions can also be used to trigger PlantWeb alerts that will be reported in Failed,
Maintenance or Advisory categories, as configured by the user. PlantWeb alerts, when enabled, can participate in the
DeltaV alarm interface tools such as the alarm banner, alarm list and alarm summary.
When a PlantWeb alert occurs, the DVC6200f sends an event notification and waits a specified period of time for an
acknowledgment to be received. This occurs even if the condition that caused the alert no longer exists. If the
acknowledgment is not received within the prespecified timeout period, the event notification is retransmitted. This
reduces the possibility of alert messages getting lost.
PlantWeb alerts are modebased. Refer to table C1 for details.
Note
Additional details on setting up and using PlantWeb Alerts can be found in Appendix C of this manual.
Electronics Alerts
Field Communicator
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts
Drive Current
Drive CurrentDrive Current (DRIVE_CURRENT [54]) displays the measured Drive Current actually flowing through
the I/P converter in percent of maximum drive.
Drive Current AlertThis alert is active when the difference between the expected Drive Current and the actual
Drive Current has exceeded the Drive Current Alert Time.
Drive Current Alert EnableWhen enabled Drive Current Alert Enable activates the Drive Current Alert.
Drive Current ShutdownThe Shutdown Trigger (SHUTDOWN_TRIGGER [76.1]) permits enabling or disabling Self
Test Shutdown for the Drive Current alert. When enabled, and the alert condition is present, the transducer Actual
69
Instruction Manual
August 2012
D103412X012
mode is placed Out of Service. The instrument will attempt to drive the valve to the Zero Power Condition and will
no longer execute transducer control function.
Drive Current Manual RecoveryShutdown Recovery (SHUTDOWN_RECOVERY [76.2]) permits enabling or
disabling Automatic recovery from Self Test Shutdown. When enabled, the transducer block will return to Target
mode when Drive Current Shutdown clears. If not enabled, the transducer block will remain Out of Service until
power is removed and restored or the user changes the transducer block target mode to Manual or Auto. In any
case, the target mode will remain Out of Service, if the condition that caused the shutdown remains or until the
shutdown trigger is disabled.
Drive Current Alert PointThe Drive Current Alert Point (DRIVE_CURRENT_ALRT_PT [76.4]) is when the absolute
difference between the Drive Current and Drive Signal exceeds the set threshold for greater than the Drive Current
Alert Time.
Drive Current Alert TimeThe Drive Current Alert Time (DRIVE_CURRENT_TIME [76.5]) is the maximum time that
the Drive Current Alert Point can be exceeded before the Drive Current Alert is active.
Drive Signal
Drive SignalThe Drive Signal (DRIVE_SIGNAL [53]) displays the commanded Drive Signal being sent to the I/P
converter as a percentage of the maximum drive.
Drive Signal Alert
The Drive Signal Alert is active if one of the following conditions exist:
Where Zero Power Condition is defined as closed:
Drive Signal < 10% and Calibrated Travel > 3%
Drive Signal > 90% and Calibrated Travel < 97%
Where Zero Power Condition is defined as open:
Drive Signal < 10% and Calibrated Travel < 97%
Drive Signal > 90% and Calibrated Travel > 3%
Drive Signal Alert EnableWhen enabled Drive Signal Alert Enable activates the Drive Signal Alert.
Processor Impaired
Program Memory AlertThis alert is active if a pending Flash or NVM failure is present.
Program Memory Alert EnableWhen enabled Program Memory Alert Enable activates the Program Memory Alert.
Program Memory ShutdownThe Shutdown Trigger (SHUTDOWN_TRIGGER [76.1]) permits enabling or disabling
Self Test Shutdown. When enabled, and the Program Memory Alert is active, the transducer Actual mode is placed
out of service. The instrument will attempt to drive the valve to the zero power condition and will no longer execute
transducer control function.
Program Memory Manual RecoveryShutdown Recovery (SHUTDOWN_RECOVERY [76.2]) permits enabling or
mode when the condition that caused Program Memory Shutdown clears. If not enabled, the transducer block will
70
Instruction Manual
D103412X012
August 2012
remain Out of Service until power is removed and restored or the user changes the transducer block target mode to
Manual or Auto. In any case, the target mode will remain Out of Service, if the condition that caused the shutdown
remains or until the shutdown trigger is disabled.
Static Memory AlertThis alert is active if a failure occurs in the FRAM memory where the static parameters are
stored.
Static Memory Alert EnableWhen enabled Static Memory Alert Enable activates the Static Memory Alert.
Static Memory ShutdownThe Shutdown Trigger (SHUTDOWN_TRIGGER [76.1]) permits enabling or disabling Self
Test Shutdown. When enabled, and the Static Memory Alert is active, the transducer Actual mode is placed out of
service. The instrument will attempt to drive the valve to the zero power condition and will no longer execute
Static Memory Manual RecoveryShutdown Recovery (SHUTDOWN_RECOVERY [76.2]) permits enabling or
mode when the condition that caused Static Memory Shutdown clears. If not enabled, the transducer block will
Manual or Auto. In any case, the target mode will remain Out of Service, if the condition that caused the shutdown
Processor AlertThis alert is active if a failure occurs in the main processor.
Processor Alert EnableWhen enabled Processor Alert Enable activates the Processor Alert.
I/O Processor AlertThis alert is active if a failure occurs in the I/O processor.
I/O Processor ShutdownThe Shutdown Trigger (SHUTDOWN_TRIGGER [76.1]) permits enabling or disabling Self
Test Shutdown. When enabled, and the I/O Processor Alert is active, the transducer Actual mode is placed out of
I/O Processor Man RecoveryShutdown Recovery (SHUTDOWN_RECOVERY [76.2]) permits enabling or disabling
Automatic recovery from Self Test Shutdown. When enabled, the transducer block will return to Target mode when
the condition that caused I/O Processor Shutdown clears. If not enabled, the transducer block will remain Out of
Service until power is removed and restored or the user changes the transducer block target mode to Manual or
Auto. In any case, the target mode will remain Out of Service, if the condition that caused the shutdown remains or
until the shutdown trigger is disabled.
Configuration Alerts
Field Communicator
TB > Configure/Setup > Detailed Setup > Alerts > Configuration Alerts

Output Block Timeout AlertThis alert is active if the analog or discrete output block has not executed for longer
than the configured timeout.
Output Block Timeout Alert EnableWhen enabled Output Block Timeout Alert Enable activates the Output Block
Timeout Alert.
Output Block Timeout ShutdownThe Shutdown Trigger (SHUTDOWN_TRIGGER [76.1]) permits enabling or
disabling Self Test Shutdown. When enabled, and the Output Block Timeout Alert is active, the transducer Actual
71
Instruction Manual
August 2012
D103412X012
mode is placed out of service. The instrument will attempt to drive the valve to the zero power condition and will no
longer execute transducer control function.
Output Block Timeout Manual RecoveryShutdown Recovery (SHUTDOWN_RECOVERY [76.2]) permits enabling or
disabling Manual recovery from Self Test Shutdown. When enabled, the transducer block will return to Target mode
when the condition that caused Output Block Timeout Shutdown clears. If not enabled, the transducer block will
Manual or Auto. In any case, the target mode will remain Out of Service if the condition that caused the shutdown
Output Block TimeoutThe Output Block Timeout (OUTPUT_BLK_TIMEOUT [76.3]) is the maximum time between
updates from the AO or DO block to the transducer block setpoint.
Blocks Set to Default
Blocks Set to Defaults AlertThis alert is active if the resource block has undergone Restart with Defaults. This will
stay active until the transducer block is changed from Out of Service.
Blocks Set to Defaults Alert EnableWhen enabled Blocks Set to Defaults Alert Enable activates the Blocks Set to
Default Alert.
Alert Key
The Alert Key (ALERT_KEY [4]) is the identification number of the plant unit. Devices in a loop or plant section can be
assigned with a common alert key to aid the operator in determining location of alerts.
Sensor Alerts
Field Communicator
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts
Travel Sensor
Travel Sensor AlertThis alert is active if the Travel Sensor reading is outside the functional range, or the sensor
becomes disconnected.
Travel Sensor Alert EnableWhen enabled Travel Sensor Alert Enable activates the Travel Sensor Alert.
Travel Sensor ShutdownThe Shutdown Trigger (SHUTDOWN_TRIGGER [76.1]) permits enabling or disabling Self
Test Shutdown. When enabled, and the Travel Sensor alert is active, the transducer Actual mode is placed out of
Travel Sensor Manual RecoveryShutdown Recovery (SHUTDOWN_RECOVERY [76.2]) permits enabling or
disabling Manual recovery from Self Test Shutdown. When not enabled, the transducer block will return to Target
mode when Travel Sensor Shutdown clears. If enabled, the transducer block will remain Out of Service until power is
removed and restored or the user changes the transducer block target mode to Manual or Auto. In any case, the
target mode will remain Out of Service, if the condition that caused the shutdown remains or until the shutdown
trigger is disabled.
Pressure Sensors
Pressure A Sensor AlertThis alert is active if the Port A Pressure Sensor reading is outside the functional range.
Pressure A Sensor Alert EnableWhen enabled Pressure A Sensor Alert Enable activates the Pressure A Sensor Alert.
72
Instruction Manual
D103412X012

August 2012
Pressure A Sensor ShutdownThe Shutdown Trigger (SHUTDOWN_TRIGGER [76.1]) permits enabling or disabling
Self Test Shutdown. When enabled, and the Port A Pressure Sensor Alert is active, the transducer Actual mode is
placed out of service. The instrument will attempt to drive the valve to the zero power condition and will no longer
execute transducer control function.
Pressure A Sensor Manual RecoveryShutdown Recovery (SHUTDOWN_RECOVERY [76.2]) permits enabling or
disabling Manual recovery from Self Test Shutdown. When not enabled, the transducer block will return to Target
mode when Pressure A Sensor Shutdown clears. If enabled, the transducer block will remain Out of Service until
power is removed and restored or the user changes the transducer block target mode to Manual or Auto. In any
case, the target mode will remain Out of Service, if the condition that caused the shutdown remains or until the
shutdown trigger is disabled.
Pressure B Sensor AlertThis alert is active if the Port B Pressure Sensor reading is outside the functional range.
Pressure B Sensor Alert EnableWhen enabled Pressure B Sensor Alert Enable activates Pressure B Sensor Alert.
Supply Pressure Sensor AlertThis alert is active if the Supply Pressure Sensor reading is outside the functional
range.
Supply Pressure Sensor Alert EnableWhen enabled Supply Pressure Sensor Alert Enable activates the Supply
Pressure Sensor Alert.
Pressure Fallback
Pressure Fallback AlertThis alert is active if a travel sensor failure or a gross travel deviation has resulted in fallback
to pressure control.
Pressure Fallback Alert EnableWhen enabled Pressure Fallback Alert Enable activates the Pressure Fallback Alert.
Temperature Sensor
Temperature Sensor AlertThis alert is active if the Temperature Sensor reading is outside the functional range.
Temperature Sensor Alert EnableWhen enabled Temperature Sensor Alert Enable activates the Temperature
Sensor Alert.
Environment Alerts
Field Communicator
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts
Supply Pressure
SupplySupply (SUPPLY_PRESSURE.VALUE [35.2]) displays the instrument supply pressure in kPa, bar, or psi.
Supply Pressure Hi AlertThis alert is active when the supply pressure exceeds the Supply Pressure Hi Alert Point.
Supply Pressure Hi Alert EnableWhen enabled Supply Pressure Hi Alert Enable activates Supply Pressure Hi Alert.
Supply Pressure Hi Alert PointThe Supply Pressure Hi Alert is active when supply pressure exceeds the Supply
Pressure Hi Alert Point (SUP_PRES_HI_ALRT_PT [76.8]).
Supply Pressure Lo AlertThis alert is active when the supply pressure is lower than the Supply Pressure Lo Alert
Point.
73
Instruction Manual
August 2012
D103412X012
Supply Pressure Lo Alert EnableWhen enabled Supply Pressure Lo Alert Enable activates Supply Pressure Lo Alert.
Supply Pressure Lo Alert PointSupply Pressure Lo Alert Point (SUP_PRES_LO_ALRT_PT [76.9]). When the supply
pressure falls below the supply pressure alert point, the supply pressure alert is active. To disable the supply
pressure alert, set Supply Pressure Alert Point to zero.
Temperature Limit
TemperatureDegrees Fahrenheit or Celsius. The temperature (TEMPERATURE [48]) is measured from a sensor
mounted on the digital valve controller's printed wiring board.
Temperature Hi AlertThis alert is active if the temperature is greater than the Temperature Hi Alert Point.
Temperature Hi Alert EnableWhen enabled Temperature Hi Alert Enable activates the Temperature Hi Alert.
Temperature Hi Alert PointThe Temperature Hi Alert is active when the instrument temperature exceeds the
Temperature Hi Alert Point (TEMP_HI_ALRT_PT [76.6]).
Temperature Lo AlertThis alert is active if the temperature is lower than the Temperature Lo Alert Point.
Temperature Lo Alert EnableWhen enabled Temperature Lo Alert Enable activates the Temperature Lo Alert.
Temperature Lo Alert PointThe Temperature Lo Alert is active when the instrument temperature is lower than the
Temperature Lo Alert Point (TEMP_LO_ALRT_PT [76.7]).
Travel Alerts
Field Communicator
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts
Note
The alerts contained in this section are valid for both travel and pressure control.
Travel Target
Travel target is the output from the characterization function.
Travel
Travel (TRAVEL.VALUE [34.2]) displays the actual position of the valve in percent (%) of calibrated travel.
Travel Deviation
Travel DeviationTravel Deviation (TRAVEL_DEVIATION [52]) displays the absolute difference in percent between
Travel Target and Actual Travel.
Travel Deviation AlertThis alert is active if the Travel deviation exceeds the Travel Deviation Alert Point by more
than the Travel Deviation Time.
Travel Deviation Alert EnableWhen enabled Travel Deviation Alert Enable actives the Travel Deviation Alert.
74
Instruction Manual
D103412X012
August 2012
Travel Deviation Alert PointThe Travel Deviation Alert Point (TVL_DEV_ALRT_PT [77.1]) is the alert point for the
difference, expressed in percent (%), between the travel target and the actual travel. When the difference exceeds
the alert point for more than the Travel Deviation Time, the Travel Deviation Alert is set.
Travel Deviation TimeTravel Deviation Time (TVL_DEV_TIME [77.2]) is the time, in seconds, that the travel
deviation must exceed the Travel Deviation Alert Point before the alert is set.
Travel Deviation DeadbandTravel Deviation Deadband (TVL_DEV_DB [77.3]) is the travel in percent threshold (%)
of ranged travel required to clear a Travel Deviation alert, once it has been set. See figure 42.
Figure 42. Travel Hi Alert Deadband
ALERT IS SET
TRAVEL ALERT
HIGH POINT
TRAVEL ALERT
DEADBAND
ALERT IS CLEARED
A6532
Travel Limit
Travel Hi Hi AlertThis alert is active if the Travel exceeds the Travel Hi Hi Alert point.
Travel Hi Hi Alert EnableWhen enabled Travel Hi Hi Alert Enable activates the Travel Hi Hi Alert.
Travel Hi Hi Alert PointTravel Hi Hi Alert Point (TVL_HI_HI_ALRT_PT [77.18]) is the value of the travel, in percent
(%) of ranged travel, which, when exceeded, sets the Travel Alert Hi Hi alert.
Travel Hi Hi DeadbandTravel Hi Hi Deadband (TVL_HI_HI_DB [77.19]) is the travel, in percent (%) of ranged travel,
required to clear a Travel Hi Hi alert, once it has been set. See figure 42.
Travel Lo Lo AlertThis alert is active if the Travel is lower than the Travel Lo Lo Alert point.
Travel Lo Lo Alert EnableWhen enabled Travel Lo Lo Alert Enable activates the Travel Lo Lo Alert.
Travel Lo Lo Alert PointThe Travel Lo Lo alert is set when the value of the travel, in percent (%) of ranged travel,
goes below the Travel Lo Lo Alert Point (TVL_LO_LO_ALRT_PT [77.12]).
Travel Lo Lo DeadbandTravel Lo Lo Deadband (TVL_LO_LO_DB [77.13]) is the travel, in percent (%) of ranged
travel, required to clear a Travel Lo Lo alert once it has been set. See figure 43.
75
Instruction Manual

August 2012
D103412X012
Figure 43. Travel Lo Alert Deadband

ALERT IS CLEARED
TRAVEL ALERT
DEADBAND
ALERT IS SET
TRAVEL ALERT
LO POINT
A65321
Travel Hi/Lo
Travel Hi AlertThis alert is active if the Travel exceeds the Travel Hi Alert point.
Travel Hi Alert EnableWhen enabled Travel Hi Alert Enable activates the Travel Hi Alert.
Travel Hi Alert PointTravel Hi Alert is set if the ranged travel rises above the Travel Hi Alert Point (TVL_HI_ALRT_PT
[77.16]). Once the alert is set, the ranged travel must fall below the alert high point set by the Travel Hi Deadband
before the alert is cleared. See figure 42.
Travel Hi DeadbandTravel Hi Deadband (TVL_HI_DB [77.17]) is the travel, in percent (%) of ranged travel, required
to clear a Travel Hi Alert, once it has been set. See figure 42.
Travel Lo AlertThis alert is active if the Travel is lower than the Travel Lo Alert point.
Travel Lo Alert EnableWhen enabled Travel Lo Alert Enable activates the Travel Lo alert.
Travel Lo Alert PointThe Travel Alert Lo alert is set when the value of the travel, in percent (%) of ranged travel,
goes below the Travel Lo Alert Point (TVL_LO_ALRT_PT [77.14]).
Travel Lo DeadbandTravel Lo Deadband (TVL_LO_DB [77.15]) is the travel, in percent (%) of ranged travel,
required to clear a travel lo alert, once it has been set. See figure 43.
Proximity Alerts
Field Communicator
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts
Note
See page 203 for additional details on using Proximity detection.
Travel
Travel displays the actual position of the valve in percent (%) of calibrated travel.
76
Instruction Manual
D103412X012
August 2012
Travel Open
Travel Open AlertThis alert is active if the Travel is greater than the Travel Open Alert Point.
Travel Open Alert EnableWhen enabled Travel Open Alert Enable activates the Travel Open Alert.
Travel Open Alert PointTravel Open Alert Point (TVL_OPEN_ALRT_PT [77.8]) is the value of the travel in percent
(%) or ranged travel, which, when exceeded, sets the Travel Open Alert.
Travel Open DeadbandTravel Open Deadband (TVL_OPEN_DB [77.9]) is the travel in percent (%) of ranged travel
required to clear a Travel Open alert, once it has been set.
Travel Closed
This alert is active if the Travel is lower than the Travel Closed Alert Point.
Travel Closed AlertThis alert is active is the Travel goes below the Travel Closed Alert Point.
Travel Closed Alert EnableWhen enabled Travel Closed Alert Enable activates the Travel Closed Alert.
Travel Closed Alert PointThe Travel Closed Alert is set when the value of the travel, in percent (%) of ranged travel,
goes below the Travel Closed Alert Point (TVL_CLOSED_ALRT_PT [77.10]).
Travel Closed DeadbandTravel Closed Deadband (TVL_CLOSED_DB [77.11]) is the travel in percent (%) of ranged
travel required to clear a Travel Closed alert, once it has been set.
Proximity
Proximity Hi Hi AlertThis alert is active if the Travel is within the detection band set by the Travel Hi Hi Alert Point
and the Travel Hi Hi Deadband.
Proximity Hi Hi Alert EnableWhen enabled Proximity Hi Hi Alert Enable activates the Proximity Hi Hi Alert.
Proximity Hi AlertThis alert is active if the Travel is within the detection band set by the Travel Hi Alert Point and
the Travel Hi Deadband.
Proximity Hi Alert EnableWhen enabled Proximity Hi Alert Enable activates the Proximity Hi Alert.
Proximity Lo AlertThis alert is active if the Travel is within the detection band set by the Travel Lo Alert Point and
the Travel Lo Deadband.
Proximity Lo Alert EnableWhen enabled Proximity Lo Alert Enable activates the Proximity Lo Alert.
Proximity Lo Lo AlertThis alert is active if the Travel is within the detection band set by the Travel Lo Lo Alert Point
and the Travel Lo Lo Deadband.
Proximity Lo Lo Alert EnableWhen enabled Proximity Lo Lo Alert Enable activates the Proximity Lo Lo Alert.
77
Instruction Manual

August 2012
D103412X012
Travel History Alerts

Field Communicator
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts
Cycle Counter
Cycle CounterThe Cycle Counter (CYCLE_COUNT [73]) records the number of times the travel changes direction.
The change in direction must occur after the deadband has been exceeded before it can be counted as a cycle. See
figure 44. You can reset the Cycle Counter by configuring it as zero.
Figure 44. Cycle Counter Deadband (set at 10%)
Deadband exceeded, and direction
changed, new Reference Point
established
Deadband Reference
Point
Deadband (+/- 5%)
Point at which
cycle is counted
A65331
Cycle Counter AlertThis alert is active if the Cycle Counter exceeds the Cycle Counter Alert Point. It is cleared after
you reset the Cycle Counter to a value less than the alert point.
Cycle Counter Alert EnableWhen enabled Cycle Counter Alert Enable activates checking of the difference between
the Cycle Counter and the Cycle Counter Alert point.
Cycle Counter Alert PointCycle Counter Alert Point (CYCLE_COUNT_ALRT_PT [77.6]) is the value of the Cycle
Counter, in cycles, which, when exceeded, sets the Cycle Counter Alert.
Cycle Counter DeadbandCycle Counter Deadband (CYCLE_COUNT_DB [77.7]) is the area around the travel
reference point, in percent (%) of ranged travel, that was established at the last increment of the Cycle Counter. This
area must be exceeded before a change in travel direction can be counted as a cycle. See figure 44.
Travel Accumulator
Travel AccumulatorTravel Accumulator (TRAVEL_ACCUM [72]) records the total change in travel, in percent (%) of
ranged travel, since the accumulator was last cleared. The value of the Travel Accumulator increments when the
magnitude of the change exceeds the Travel Accumulator Deadband. See figure 45. You can reset the Travel
Accumulator by configuring it to zero.
78
Instruction Manual
D103412X012
August 2012
Figure 45. Travel Accumulator Deadband (set at 10%)

Deadband exceeded,
new Reference Point
established
This amount of change is

added to the Travel
Accumulator
Deadband Reference
Point
A6534
Deadband (+/- 5%)
Travel Accumulator AlertThis alert is active if the Travel Accumulator exceeds the Travel Accumulator Alert Point.
The Travel Accumulator Alert is set when the Travel Accumulator value exceeds the Travel Accumulator Alert Point.
It is cleared after you reset the Travel Accumulation to a value less than the alert point.
Travel Accumulator Alert EnableWhen enabled Travel Accumulator Alert Enable activates checking of the
difference between the Travel Accumulator value and the Travel Accumulator Alert Point.
Travel Accumulator Alert PointTravel Accumulator Alert Point (TVL_ACCUM_ALRT_PT [77.4]) is the value of the
Travel Accumulator, in percent (%) of ranged travel, which, when exceeded, sets the Travel Accumulator Alert.
Travel Accumulator DeadbandTravel Accumulator Deadband (TVL_ACCUM_DB [77.5]) is the area around the
travel reference point, in percent (%) of ranged travel, that was established at the last increment of the
accumulator. This area must be exceeded before a change in travel can be accumulated. See figure 45.
Performance Alerts
Field Communicator
TB > Configure/Setup > Detailed Setup > Alerts > Performance Alerts
Note
Performance Alerts are only available with a PD tier instrument. Additionally, for the PD alerts to function properly:
The transducer block mode must not be out of service.
The travel/pressure control state must be in travel control mode, and
Bench Set Hi, Bench Set Lo, and Nominal Supply Pressure must be set in the Spec Sheets, then enable the Performance
Information instrument alert (PERF_ENABLE [75.7]).
PD Inside Status
PD Inside Status shows the status of Performance Diagnostics.
79

August 2012
Instruction Manual
D103412X012
PD Run
PD Run enables or disables Performance Diagnostics in the instrument (PD Inside). Selecting PD Off disables PD Inside.
Selecting PD On enables PD Inside.
Performance Critical
Performance Critical AlertThis alert is active if the instrument is no longer able to control the valve or performance
has been dramatically reduced.
Performance Critical Alert EnableWhen enabled Performance Critical Alert Enable activates the Performance
Critical Alert.
Performance Reduced
Performance Reduced AlertThis alert is active if the instrument has detected a reduction in performance.
Performance Reduced Alert EnableWhen enabled Performance Reduced Alert Enable activates the Performance
Reduced Alert.
Performance Information
Performance Information AlertThis alert is active if the instrument has detected a condition that may pertain to
control performance.
Performance Information Alert EnableWhen enabled Performance Information Alert Enable activates the
Performance Information Alert.
PlantWeb Alert Enable

Field Communicator
TB > Configure/Setup > Detailed Setup > Alerts > PlantWeb Alert Enable
Failed EnableFailed Enable (FAILED_ENABLE [62]) enables or disables conditions that can cause a failed alert. A
failed alert indicates a failure within the device that will make the device or some part of the device nonoperational.
Table C2 lists the available PlantWeb alerts.
Maintenance EnableMaintenance Enable (MAINT_ENABLE [63]) enables or disables conditions that can cause a
maintenance alert. A maintenance alert indicates the device or some part of the device needs maintenance soon.
Table C2 lists the available PlantWeb alerts.
Advise EnableAdvise Enable (ADVISE_ENABLE [64]) enables or disables conditions that can cause an advisory alert.
An advisory alert indicates informative conditions that do not have a direct impact on the device's primary
functions. Table C2 lists the available PlantWeb alerts.
PlantWeb Alert Reporting

Field Communicator
TB > Configure/Setup > Detailed Setup > Alerts > PlantWeb Alert Reporting
Failed SuppressFailed Suppress (FAILED_MASK [65]) determines which of the failed alert conditions are
suppressed so that they are not reported. Even if reporting is suppressed, the bit in Failed Active (FAILED_ACTIVE
[59]) is still set.
Maintenance SuppressMaintenance Suppress (MAINT_MASK [66]) determines which of the maintenance alert
conditions are suppressed so that they are not reported. Even if reporting is suppressed, the bit in Maintenance
Active (MAINT_ACTIVE [60]) is still set.
80
Instruction Manual
D103412X012
August 2012
Advise SuppressAdvise Suppress (ADVISE_MASK [67]) determines which of the advise alert conditions are
suppressed so that they are not reported. Even if reporting is suppressed, the bit in Advise Active (ADVISE_ACTIVE
[61]) is still set.
Instrument
Field Communicator
TB > Configure/Setup > Detailed Setup > Instrument
Tag DescriptionThe Tag Description (TAG_DESC [2]) is a 32 character description used to assign a unique
description to each block within the digital valve controller to describe the intended application for the block.
Pressure UnitsDefine the output and supply pressure units (PRESSURE_UNITS [90]) in either psi, bar, or kPa.
Temperature UnitsEnter the temperature units (TEMPERATURE_UNITS [89]) in degrees Fahrenheit or Celsius. The
temperature is measured from a sensor mounted on the digital valve controller's printed wiring board.
Travel UnitsDefine the units for valve travel (TVL_UNITS [91]) in inches, centimeters, millimeters or degrees.
Length UnitsDefine the units for valve dimensions (LENGTH_UNITS [92]) in inches, centimeters, or millimeters.
Area UnitsDefine the units for actuator area (AREA_UNITS [93]) in inches2, centimeter2 or millimeter2.
Spring Rate UnitsDefine the units for actuator spring rate (SPRING_RATE_UNITS [94]) in lbs/in2 or N/M.
Relay TypeEnter the Relay Type (RELAY_TYPE [42.5]).There are three categories of relays that result in
combinations from which to select.
Relay Type: The relay type is printed on the label affixed to the relay body:
A = doubleacting or single acting
B = singleacting, reverse
C= singleacting, direct
Special App: This is used in singleacting applications where the unused output port is configured to read the
pressure downstream of a solenoid valve. See page 29 for additional information.
Lo Bleed: The label affixed to the relay body indicates it is a low bleed version.
Zero Power ConditionZero Power Condition (ZERO_PWR_COND [42.2]) identifies whether the valve is open or
closed when instrument power is lost. If you are unsure how to set this parameter, disconnect the segment loop
power to the instrument. The resulting valve travel is the Zero Power Condition.
Maximum Supply PressureEnter the maximum supply pressure (MAX_SUPP_PRESS [42.6]) in psi, bar, or kPa,
depending on what was selected for pressure units.
Calibration PersonName of the person performing last calibration (XD_CAL_WHO [31]).
Calibration LocationIndicates the location of the last instrument calibration (XD_CAL_LOC [29]).
Calibration DateEnter a date with the format MM/DD/YY. Date is a userdefined variable that provides a place to
save the date of the last calibration (XD_CAL_DATE [30]).
Last Calibration TypeIndicates the type of the last calibration performed on the instrument. Possible values are:
Not Calibrated, Single Point Calibration, Auto Calibration, Manual Calibration.
81
Instruction Manual
August 2012
D103412X012
Valve and Actuator

Field Communicator
TB > Configure/Setup > Detailed Setup > Valve and Actuator
Valve
Valve ManufacturerEnter the identification number of the manufacturer of the valve (VALVE_MAN_ID [25]) on
which the instrument is mounted. Select from the dropdown list or enter the manufacturer's identification number
as defined by the Fieldbus Foundation. For Fisher, the manufacturer ID hex value is 005100.
Valve Model NumberEnter the valve model number (VALVE_MODEL_NUM [26]), (design letter or type number)
for the valve on which the instrument is mounted.
Valve Serial NumberEnter the serial number of the valve (VALVE_SN [27]) on which the instrument is mounted.
Valve StyleEnter the type of valve (VALVE_TYPE [28]), slidingstem or rotary, on which the instrument is mounted.
Valve SizeEnter the size of the valve (VALVE_SIZE [83.1]) on which the instrument is mounted.
Valve ClassEnter the valve pressure class rating (VALVE_CLASS [83.2]).
Rated TravelEnter the valve rated travel (RATEDTRAVEL [83.3]) in inches or mm for sliding-stem valves, or in
degrees of rotation for rotary valves.
Actual TravelEnter the actual travel (ACTUAL_TRAVEL [83.4]) in inches or mm for sliding-stem valves, or in degrees
of rotation for rotary valves.
Shaft Stem DiameterEnter the valve stem diameter (SHAFT_STEM_DIA [83.5]) in inches or millimeters.
Packing TypeEnter the valve packing construction (PACKING_TYPE [83.6]).
Inlet PressureEnter the valve inlet pressure (INLET_PRESSURE [83.7]).
Outlet PressureEnter the valve outlet pressure (OUTLET_PRESSURE [83.8]) in psig, kPa, Bar, inHg, inH2O, or kg/cm2.
Trim
Seat TypeEnter the valve seat type (SEAT_TYPE [84.1]).
Leak ClassEnter the valve leak class (LEAK_CLASS [84.2]).
Port DiameterEnter the valve port diameter (PORT_DIAMETER [84.3]) in inches or mm.
Port TypeEnter the valve port type (PORT_TYPE [84.4]).
Flow DirectionEnter the flow direction (FLOWDIRECTION [84.5]) through the valve.
Push Down ToEnter the effect on valve movement when the stem is moved down (PUSH_DOWN_TO [84.6]).
Flow Tends ToEnter the effect on valve travel with increasing flow (FLOW_TENDS_TO [84.7]).
Unbalanced AreaEnter the valve unbalanced area (UNBALANCED_AREA [84.8]) in in2 or mm2.
82
Instruction Manual
D103412X012
August 2012
Actuator
Actuator ManufacturerEnter the manufacturer's identification number (ACT_MAN_ID [22]) of the actuator on
which the instrument is mounted. Select from the dropdown list or enter the manufacturer's identification number
as defined by the Fieldbus Foundation. For Fisher, the manufacturer ID hex value is 005100.
Actuator Model NumberEnter the type number for the actuator (ACT_MODEL_NUM [23]) on which the
instrument is mounted.
Actuator StyleSelect the Actuator Style (ACTUATOR_STYLE [42.1]), spring & diaphragm, piston doubleacting
without spring, piston singleacting with spring, or piston doubleacting with spring.
Actuator Serial NumberEnter the serial number (ACT_SN [24]) for the actuator on which the instrument is
mounted.
Actuator SizeEnter the size of the actuator (ACTUATOR_SIZE [85.1]) on which the instrument is mounted.
Actuator Fail ActionSets actuator action to be performed upon loss of actuator air pressure (ACT_FAIL_ACTION
[21]).
View / Edit Feedback ConnectionRefer to table 410 for Feedback Connection options. Choose the assembly that
matches the actuator travel range.
Note
(on the back of the DVC6200f housing) has to remain within this range throughout the entire valve travel. See figure 22. The
linear magnet assemblies are symmetrical. Either end may be up.
Table 410. Feedback Connection Options

Magnet Assembly
Travel Range
mm
Inch
Degrees
SStem #7
4.2-7
0.17-0.28
SStem #19
8-19
0.32-0.75
SStem #25
20-25
0.76-1.00
SStem #38
26-38
1.01-1.50
SStem #50
39-50
1.51-2.00
SStem #100
51-100
2.01-4.00
SStem #210
101-210
4.01-8.25
SStem #1 Roller
60-90
RShaft Window #1
60-90
RShaft Window #2
60-90
RShaft End Mount
60-90
WARNING
If you answer YES to the prompt for permission to move the valve when setting the Travel Sensor Motion, the instrument
will move the valve through its full travel range. To avoid personal injury and property damage caused by the release of
83
Instruction Manual
August 2012
D103412X012
process fluid.
Travel Sensor Motion (TRAVEL_SEN_MOTION [42.3]) establishes the proper valve travel sensor (feedback)
rotation/movement. For quarterturn actuators determine rotation by viewing the rotation of the magnet assembly
from the back of the instrument.
Note
Travel Sensor Motion in this instance refers to the motion of the magnet assembly. Note that the magnet assembly may be
referred to as a magnetic array in user interface tools.
For instruments with relay A or C If increasing air pressure at output A causes the magnet assembly to move up, or the
actuator shaft to rotate counterclockwise, enter Towards Top of Instrument/CCW. If it causes the magnet assembly
to move down, or the actuator shaft to rotate clockwise, enter Away From Top of Instrument/CW. For instruments
with relay B.
For instruments with relay B If decreasing air pressure at output B causes the magnet assembly to move up, or the
actuator shaft to rotate counterclockwise, enter Towards Top of Instrument/CCW. If it causes the magnet assembly
to move down, or the actuator shaft to rotate clockwise, enter Away From Top of Instrument/CW.
Lever StyleEnter the lever style (LEVER_STYLE [85.10]) for rotary actuators as either Pivot Point or Rack and Pinion.
Lever Arm LengthDefines the lever arm length (MOMENT_ARM [85.11]) for rotary actuators.
Effective AreaEnter the actuator effective area (EFFECTIVE_AREA [85.2]) in in2, cm2, or mm2.
AirSelect Opens or Closes, indicating the effect of increasing air pressure (AIR [85.3]) on the valve travel.
Upper Bench SetEnter the upper actuator operating pressure (UPPER_BENCH_SET [85.5]).
Lower Bench SetEnter the lower actuator operating pressure (LOWER_BENCH SET [85.4]).
Nominal Supply PressureEnter the nominal instrument supply pressure (NOMINAL_SUPPLY PRESSURE [85.6]).
Spring RateEnter the actuator spring rate (SPRING_RATE [85.7]) in lbsin or Nm.
Reference
Trim Style 1Enter the valve trim style (TRIM_STYLE_1 [84.9]).
Trim Style 2Enter the valve trim style (TRIM_STYLE_2 [84.10]).
Stroking Time OpenEnter the time required to stroke the valve from closed to open (STROKING_TIME_OPEN
[85.8]).
Stroking Time CloseEnter the time required to stroke the valve from open to close (STROKING_TIME_CLOSE
[85.9]).
84
Instruction Manual
D103412X012
August 2012
Table 411. Output Block PV Status

FEATURE_SEL
PW Alarms Set PV Status
Enabled
Transducer Mode,
Actual
AO / DO
PV Status(2)
AO / DO
PV Substatus
AO/DO PV
Limit Substatus(1)
OOS
Bad
Device Failure
Constant
Man
Bad
Nonspecific
Constant
Auto
Fail
Uncertain
Subnormal
See table 412
Auto
Maintenance, no Fail
Uncertain
Nonspecific
See table 412
Good
Advisory
See table 412
Auto
Advisory, no Fail, no
Maintenance
None
Good
NonSpecific
See table 412
OOS
Bad
Device Failure
Constant
Man
Bad
NonSpecific
Constant
Auto
Fail
Good
NonSpecific
See table 412
Auto
Maintenance, no Fail
Good
NonSpecific
See table 412
Auto
Advisory, no Fail, no
Maintenance
Good
NonSpecific
See table 412
Auto
None
Good
NonSpecific
See table 412
Auto
Not Enabled
Active PlantWeb
Alarms
NOTES:
X = No Effect
1. PV limit substatus reflects only READBACK limit substatus. SP limit substatus reflects only out block rate limits.
2. Firmware Revision 1.1 and earlier will set AO/DO PV Status to Bad if Feedback Sensor has failed, i.e.; Travel Sensor Fail. However, if the Travel Sensor fails, and the instrument falls back to
pressure, PV Status will remain good.
MAI Channel Map

Field Communicator
TB > Configure/Setup > Detailed Setup > MAI Channel Map
Allows the user to specify which transducer block parameter is available through each of the MAI Block channels
(MAI_CHANNEL_1 through MAI_CHANNEL_8 [95.1 through 95.8]). Transducer block parameters available to each
channel:
11
12
13
14
15
16
17
=
=
=
=
=
=
=
18
19
10
11
12
13
FINAL_VALUE
TRAVEL_TARGET
FINAL_POSITION_VALUE
TRAVEL
SUPPLY_PRESS
ACT_PRESS_A
ACT_PRESS_B
=
=
=
=
=
=
ACT_PRESS_DIFF
DRIVE_SIGNAL
TRAVEL_DEVIATION
TEMPERATURE
CYCLE_COUNT
TRAVEL_ACCUM
Table 412. Limit Sub Status

Out Block
Transducer Mode
In Cutoff Region
Rate Limited
Limit SubStatus
AO, DO
OOS
Constant
AO, DO
MAN
Constant
AO
AUTO
High
High Limited
AO
AUTO
Low
Low Limited
AO
AUTO
High
High Limited
AO
AUTO
Low
Low Limited
AO
AUTO
None
None
Not Limited
DO
AUTO
High
High Limited
DO
AUTO
Low
Low Limited
DO
AUTO
None
Not Limited
NOTE: X = No Effect
85
Instruction Manual

August 2012
D103412X012
Alert Handling
Field Communicator
TB > Configure/Setup > Detailed Setup > Alert Handling
PlantWeb Alert Simulate

When enabled, PlantWeb Alert Simulate (PWA_SIMULATE [39]) allows the user to write to the following PlantWeb and
Instrument alert parameters; Failed Active, Maintenance Active, Advise Active, Environment Active, Travel Active,
Proximity Active, Travel History Active, Performance Active, PD Event Active, PD Detail 1 Active, PD Detail 2 Active, PD
Detail 3 Active, PD Detail 4 Active, PD Detail 5 Active, PD Detail 6 Active. This provides a way to simulate these alerts
for testing. In order to enable PWA Simulate, the Aux Terminal must be jumpered.
PlantWeb Alert Simulate is cleared on a power cycle. It can also be cleared manually, or by removing the Aux terminal
jumper.
Simulate Active Alerts
Failed ActivePermits simulating an active Failed alarm (FAILED_ACTIVE [59]).
Maintenance ActivePermits simulating an active Maintenance alarm (MAINT_ACTIVE [60]).
Advise ActivePermits simulating an active Advisory alarm (ADVISE_ACTIVE [61]).
PlantWeb Alert Handling
PlantWeb Alerts Set PV StatusWhen selected, PlantWeb alerts will set the PV status according to table 411.
Block Error ReportingWhen enabled, the AO or DO BLOCK_ERR [6] parameter will report PlantWeb Alerts. the
same as Block Error in the resource block.
Block Error bit 6 (Device Needs Maintenance Soon) will report any active PlantWeb Maintenance Alert.
Block Error bit 13 (Device Needs Maintenance Now) will report any active PlantWeb Failed Alert.
Block Errors
Table 413 lists conditions reported in the BLOCK_ERR [6] and XD_ERR [11] parameters. Conditions in italics are not
applicable for the transducer block and are provided only for your reference.
Table 413. Transducer Block BLOCK_ERR and XD_ERROR Conditions
Condition Number
86
Other (N/A)
Block Configuration Error Indicates that one of the following parameters have been configured out of the proper range: 15,
16, 47.1, 47.2, 46.3, 46.5, 42.7, 42.8.
Link Configuration Error (N/A)
Local Override (N/A)
Device Fault State - (NA)
Maintenance Needed Soon (N/A)
Input failure/process variable has Bad status (N/A)
Output failure (N/A)
Memory failure (N/A)
10
Lost Static Data Indicates that manufacturing functional or thermal tests were incomplete
11
Lost NV Data (N/A)
12
Readback Check Failed (N/A)
13
Device Needs Maintenance Now Indicates that manufacturing functional or thermal tests were incomplete
14
Power Up (N/A)
15
Out of Service Indicates Out of Service Mode.
Instruction Manual
D103412X012
August 2012
Transducer Block Parameter List

Protection Category: Indicates whether or not the parameter is writable while the PROTECTION parameter
is set to a particular level.
-N/A indicates a readonly parameter that is never writable, regardless of the value of the PROTECTION parameter
-NONE indicates a readonly parameter that is always writable, regardless of the value of the PROTECTION parameter
-CAL indicates a parameter that is only writable while the value of the PROTECTION parameter is NONE.
-SETUP indicates a parameter that is only writable while the value of the PROTECTION parameter is NONE or CAL.
-ALL indicates a parameter that is writable while the value of the PROTECTION parameter is NONE, CAL, or SETUP & CAL.
Double indentation and shaded Index Number indicates subparameter

Table 414. Transducer Block Parameter Definitions
Label
PARAMETER_NAME
Index
Number
RO /
RW
Mode
Static Revision
ST_REV
RO
N/A
Tag Description
TAG_DESC
RW
ALL
Strategy
STRATEGY
RW
ALL
Alert Key
ALERT_KEY
Block Mode
MODE_BLK
RW
ALL
Range
0 to 65535
0 to 65535
1 to 255
Initial Value
Protect
Category
N/A
N/A
Data Type: Uint16

The revision level of the static data.
Increments by one each time a static
parameter is written. The value is
reset to 0 whenever a Restart with
Defaults is performed. See
Restarting the Instrument.
NULL
SETUP
Data Type: String

The description of the block.
SETUP
Data Type: Uint16

Used to help group blocks.
SETUP
Data Type: Uint8

The identification number of the
plant unit. Devices in a loop or plant
section can be assigned with a
common alert key to aid the
operator in determining location of
alerts.
TARGET
5.1
RW
ALL
7: OOS
NONE
ACTUAL
5.2
RO
N/A
N/A
N/A
3:AUTO
4:MANUAL
7: OOS
NONE
3:AUTO
NONE
N/A
N/A
PERMITTED
5.3
RW
ALL
NORMAL
5.4
RW
ALL
Block Error
BLOCK_ERR
RO
N/A
3:AUTO
4:MANUAL
7:OOS
3: Simulate Active
10: Static Memory Failed
(Functional or thermal
data missing)
13: Maintenance
Needed Now
(Functional or thermal
data missing)
15: OutofService
Description
Data Type: DS69

The actual, target, permitted, and
normal modes.
Actual: The current mode of
the block
Permitted: Allowed modes for
Target
Normal: Most common mode
for Target
Data Type: Bit String (2 byte)

Error status associated with
hardware or firmware for the
transducer block.
-Continued-
87
Instruction Manual

August 2012
D103412X012
Table 414. Transducer Block Parameter Definitions (Continued)

Label
PARAMETER_NAME
Update Event
UPDATE_EVT
Index
Number
RO /
RW
Mode
Range
Initial Value
Protect
Category
UNACKNOWLEDGED
7.1
RW
ALL
0=Undefined
1=Acknowledged
2=Unacknowledged
NONE
UPDATE_STATE
7.2
RO
N/A
0=Undefined
1=Updated reported
2=Update Not reported
N/A
TIME_STAMP
7.3
RO
N/A
N/A
STATIC_REVISION
7.4
RO
N/A
N/A
RELATIVE_INDEX
7.5
RO
N/A
N/A
RW
ALL
0=Undefined
1=Acknowledged
2=Unacknowledged
NONE
N/A
0=Undefined
1=Clear-reported
2=Clear-not reported
3=Active-reported
4=Active-not reported
N/A
Block Alarm
BLOCK_ALM
UNACKNOWLEDGED
ALARM_STATE
TIME_STAMP
Description
Data Type: DS73

Alert generated by change to static
data.
8
8.1
8.2
8.3
RO
RO
N/A
N/A
N/A
Data Type: DS72

Used to report the BLOCK_ERR
alarm to the host system
SUBCODE
8.4
RO
N/A
Subcode: Bit Number in

BLOCK_ERR
VALUE
8.5
RO
N/A
Value of parameter at
alarm time for a single
alarm, 0 for multiple
alarms
N/A
Transducer Directory
TRANSDUCER_DIRECTORY
RO
N/A
1,1
1,1
N/A
Data Type: Array [2] of Unit16

Not used
Transducer Type
TRANSDUCER_TYPE
10
RO
106
106
N/A
Data Type: Uint16

Identifies the type of the transducer.
Transducer Error
XD_ERROR or TDC_ERROR
11
RO
Valid Numbers:0 = No
Error
N/A
Data Type: Uint8

Error code for the transducer block.
Collection Directory
COLLECTION_DIRECTORY
12
RO
1,1,1,1,1
1,1,1,1,1
N/A
Data Type: Array [5] of Unit32

Not used

FINAL_VALUE
13
Setpoint Status
STATUS
13.1
RW
MAN
OOS
Setpoint
VALUE
13.2
RW
MAN
OOS
N/A
NONE
N/A
NONE
Setpoint Range
FINAL_VALUE_RANGE
-25 to 125
14
EU_100
14.1
RO
N/A
100
100
N/A
EU_0
14.2
RO
N/A
N/A
UNITS_INDEX
14.3
RO
N/A
PERCENT
1342
N/A
DECIMAL
14.4
RO
N/A
N/A
-Continued-
88
Data Type: DS65

In Travel Control: Setpoint for valve
travel in %, prior to characterization.
In Pressure Control: Setpoint for
implied valve travel as % or pressure
range, prior to characterization.
FINAL_VALUE is not updated unless
the AO block is selected in
FEATURE_SELECT. For example,
FINAL_VALUE still has last value
written by AO channel 1 when DO is
in control.
Data Type: DS68
High and Low range limit values,
engineering units code, and number
of digits to the right of the decimal
place to be used to display the Final
Value.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Travel Cutoff Hi
FINAL_VALUE_CUTOFF_HI
Travel Cutoff Lo
FINAL_VALUE_CUTOFF_LO
Index
Number
15
16
RO /
RW
RW
Mode
MAN
OOS
RW
MAN
OOS
Range
-25 to 125
-25 to 125
Initial Value
99.5
Protect
Category
SETUP
0.5
SETUP
N/A
N/A
17
Description
Data Type: Float
When the servo goes above this % of
span, the stem position goes to the
upper limit. Cutoffs are OFF when
Low is at -25% and high is at +125%.
Must be > low cutoff + .625%.
Data Type: Float
When the servo goes below this % of
span, the stem position goes to the
lower limit. Cutoffs are OFF when
Low is at -25% and high is at +125%.
Must be < hi cutoff - .625%.
Data Type: DS65
In Travel Control: Valve travel in %,
decharacterized to correlate with
Setpoint (FINAL_VALUE [13]).
In Pressure Control: Implied valve
travel as a % of pressure range,
decharacterized to correlate with
Setpoint (FINAL_VALUE [13]).
Controls AI channel 3.
Data Type: Float
Travel Control Only. Gain of servo.
Travel Status (Decharacterized)

STATUS
17.1
RO
N/A
Travel (Decharacterized)
VALUE
17.2
RO
N/A
-25 to 125%

SERVO_GAIN
18
RW
MAN
OOS
>=0
4.4
SETUP

SERVO_RESET
19
RW
MAN
OOS
> = 0 , = 0 causes wind

down
9.4
SETUP
Data Type: Float

Travel Control Only. If set to 0, will
cause integrator to wind down.

SERVO_RATE
20
RW
MAN
OOS
>=0
3.0
SETUP
Data Type: Float

Travel Control Only. Rate of servo.
Actuator Fail Action

ACT_FAIL_ACTION
21
RW
MAN
OOS
0=Uninitialized
1=SelfClosing
2=SelfOpening
1=
SelfClosing
SETUP
Data Type: Enum (Uint8)

Action performed by actuator in the
event of air pressure.
Actuator Manufacturer
ACT_MAN_ID
22
RW
ALL
0x5100
SETUP
Data Type: Uint32

The actuator manufacturer
identification number.
Actuator Model Number

ACT_MODEL_NUM
23
RW
ALL
Null
SETUP

Model number of actuator.
Actuator Serial Number

ACT_SN
24
RW
ALL
Null
SETUP

Serial number of actuator.
Valve Manufacturer
VALVE_MAN_ID
25
RW
ALL
0x5100
SETUP
Data Type: Uint32

The valve manufacturer
identification number.
Valve Model Number

VALVE_MODEL_NUM
26
RW
ALL
Null
SETUP

The valve model number.
Valve Serial Number

VALVE_SN
27
RW
ALL
Null
SETUP

The valve serial number.
Valve Style
VALVE_TYPE
28
RW
ALL
1=sliding-stem
SETUP

Selects Rotary or sliding-stem.
Calibration Location
XD_CAL_LOC
29
RW
ALL
Null
CAL

Where device was last calibrated.
Calibration Date
XD_CAL_DATE
30
RW
ALL
Uninitialized
CAL
Data Type: Date

Date of last calibration.
Calibration Person
XD_CAL_WHO
31
RW
ALL
Null
CAL

Name of person performing last
calibration.
1=sliding-stem
2=Rotary
N/A
-Continued-
89
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
SETPOINT_D
Index
Number
RO /
RW
Mode
32.1
RW
MAN
OOS
Setpoint(D)
VALUE
32.2
RW
MAN
OOS
33.1
RO
N/A
Travel (D)
VALUE
33.2
RO
N/A
NONE
0 = closed 1 = open
5,10,15.. = %
NONE
N/A
0 = closed 1 = open
5,10,15.. = %
N/A
34
Travel Status
STATUS
34.1
RO
N/A
N/A
Travel
VALUE
34.2
RO
N/A
N/A
SUPPLY_PRESSURE
35.1
RO
N/A
N/A
Supply Pressure
VALUE
35.2
RO
N/A
N/A
36
Pressure A Status
STATUS
36.1
RO
N/A
N/A
Pressure A
VALUE
36.2
RO
N/A
N/A
PRESSURE_B
Description
Data Type: DS_66
SETPOINT_D is not updated unless
the DO block is selected in
FEATURE_SEL.
STATUS indicates the validity of
value, set by the DO block
OUT.STATUS
VALUE is the discrete value of
setpoint. Only values of 0, 1, or
increments of 5 up to 95 are
allowed. Written by DO channel 22.
Data Type: DS_66
VALUE.
VALUE: 0=closed , 1=open
5,10,15.. = %. Controls DI Channel
23
Data Type: DS65
In Travel Control: Actual valve travel
in % of calibrated travel range.
In Pressure Control: Implied valve
travel in % of pressure range.
35
Supply Pressure Status

STATUS
PRESSURE_A
37
Pressure B Status
STATUS
37.1
RO
N/A
N/A
Pressure B
VALUE
37.2
RO
N/A
N/A
-Continued-
90
Protect
Category
33
Travel(D) Status
STATUS
TRAVEL
Initial Value
32
Setpoint(D) Status
STATUS
TRAVEL_D
Range
Data Type: DS65

VALUE. VALUE is pressure of air
supply, controls AI channel 5.
Data Type: DS65

STATUS Indicates the validity of
VALUE.
Pressure of primary air output,
controls AI channel 6.
Data Type: DS65
VALUE. VALUE is the
Pressure on secondary output,
controls AI channel 7.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
PRESSURE_DIFF
Index
Number
RO /
RW
Mode
Range
Initial Value
Protect
Category
38
Pressure Differential Status

STATUS
38.1
RO
N/A
N/A
Pressure Differential
VALUE
38.2
RO
N/A
N/A
PWA Simulate
PWA_SIMULATE
39
Grant Deny
GRANT_DENY
40
RO or
RW*
ALL
GRANT
40.1
RW
ALL
DENY
40.2
RW
ALL
Travel Pressure Control

TVL_PRESS_CONTROL
1=Simulate Off
2=Simulate Enabled
0:Program
1:Tune
2:Alarm
3:Local
Description
Data Type: DS65
VALUE. VALUE is the difference
between PRESSURE_A and
PRESSURE_B, controls AI channel 8.
When this is set to 2 all the alert
ACTIVE parameters can be written,
except for INST_ALERTS_ACTIVE.
SHUTDOWN_ALERT_ACTIVE. This
allows alerts to be simulated for
testing with hosts. NOTE: only
ACTIVE parameters are affected by
this. * PWA Simulate is RW only if a
jumper is installed across the Aux
Terminal. If no jumpered is installed
across the Aux Terminal, PWA
Simulate is RO.
1=Simulate Off
ALL
all bits cleared
NONE
all bits cleared
NONE
1=Travel
SETUP

Selects whether travel sensor or port
A pressure is used for feedback.
N/A

Indicates which sensor is used for
feedback
Data Type: DS50

Options for controlling access of
host computer and local control
panels to operating, tuning, and
alarm parameters of the block. Has
no effect on the DVC6200f.
GRANT: 0=N/A, 1= granted
DENY: 0=N/A, 1= denied
41
TVL_PRESS_SELECT
41.1
RW
ALL
1=Travel
2=Pressure
3=TVL/PRESS Auto Recv
4=TVL/PRESS Man Recv
Travel/Pressure State
TVL_PRESS_STATE
41.2
RO
N/A
1=Travel
2=Pressure
-Continued-
91
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Basic Setup
BASIC_SETUP
Index
Number
RO /
RW
Mode
Range
Protect
Category
Description
42
Actuator Style
ACTUATOR_STYLE
42.1
RW
MAN
OOS
1=Spring & Diaphragm

2=PistonDbl w/o Spring
3=PistonDbl w/Spring
4=Piston Sgl w/Spring
1=Spring &
Diaphragm
SETUP
Zero Power Condition

ZERO_PWR_COND
42.2
RW
MAN
OOS
1=Valve Closed
2=Valve Open
1=Valve Closed
SETUP
Data Type: (Uint8)

Enum Identifies whether the valve is
open or closed when instrument
power is lost.

TRAVEL_SEN_MOTION
42.3
RW
MAN
OOS
1=Counter Clockwise
2=Clockwise
1=Counter
Clockwise
SETUP
MAN
OOS
100: Default Array

64: SStem #19 Array
65: SStem #25 Array
66: SStem #38 Array
67: SStem #50 Array
70: SStem #100 Array
74: SStem #200 Array
85: SStem #1 Roller
Array
90: RShaft End Array
95: RShaft #1 Window
Array
97: RShaft #2 Window
Array
SETUP
SETUP
Feedback Connection
FEEDBACK_CONN
42.4
RW
Relay Type
RELAY_TYPE
42.5
RW
MAN
OOS
1=Relay A or CDouble or
Single Direct
2=Relay BSingle Reverse
5=Relay CSpecial App.
Single Direct
6=Relay BSpecial App.
Single Reverse
9=LoBleed Relay A or
=Relay A or
CDouble or Single
CDouble or
Direct
Single Direct
10=LoBleed Relay B
Single Reverse
13=LoBleed Relay
CSpecial App.Single
Direct
10=LoBleed Relay
BSpecial App.-Single
Reverse
Maximum Supply Pressure

MAX_SUPP_PRESS
42.6
RW
MAN
OOS
> 0, < = 150
35 psig
SETUP
Data Type: Float
Pressure Range Hi
PRESS_RANGE_HI
42.7
RW
MAN
OOS
> 0, < = 150
15.0 psig
SETUP
Data Type: Float

Defines pressure corresponding to
max pressure in pressure control
mode.
Pressure Range Lo
PRESS_RANGE_LO
42.8
RW
MAN
OOS
> = 0, < = 150
3.0 psig
SETUP
Data Type: Float

Defines pressure corresponding to
minimum pressure in pressure
control mode.
Travel Calibration Trigger

TVL_CAL_TRIGGER
42.9
RW
MAN
OOS
1 = Aux Term ignored
SETUP
Not available in the DVC6200f
Travel Tuning Set

TVL_TUNING_SET
42.10
RW
MAN
OOS
1=B, 2= C, ...12=M
23=X
2=C
SETUP

Letter (B through M or X)
Pressure Tuning Set

PRESS_TUNING_SET
42.11
RW
MAN
OOS
1=B, 2=C, ...12= M

23=X
2=C
SETUP

Letter (B through M or X)
-Continued-
92
Initial Value
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
TRAVEL_CAL
Index
Number
RO /
RW
Mode
Range
Initial Value
Protect
Category
Description
43
Travel Count
TVL_COUNT
43.1
RO
N/A
Travel Hi Calibration
TVL_HI_CAL
43.2
RW
MAN
OOS
<TVL_FAC_HI
>TVL_LO_CAL
CAL
Data Type: Uint16

Maximum drive calibration point
Travel Lo Calibration
TVL_LO_CAL
43.3
RW
MAN
OOS
>TVL_FAC_LO
<TVL_HI_CAL
CAL
Data Type: Uint16

Minimum drive calibration point
Travel Crossover
TVL_CROSSOVER
43.4
RW
MAN
OOS
>0% < = 100%
50%
CAL
Data Type: Float

Not used for the DVC6200f
Travel Fac Hi
TVL_FAC_HI
43.5
RO
N/A
Set by Factory
N/A
Data Type: Uint16

Maximum value of travel sensor
counts. Set at factory.
Travel Fac Lo
TVL_FAC_LO
43.6
RO
N/A
Set by Factory
N/A
Data Type: Uint16

Minimum value of travel sensor
counts. Set at factory.
Travel IP Bias
TVL_IP_BIAS
43.7
RW
MAN
OOS
0% - 100%
70%
CAL
Data Type: Float
Travel MLFB Bias

TVL_MLFB_BIAS
43.8
RW
MAN
OOS
0 - 100%
50%
CAL
Data Type: Float
Last Calibration Type

TVL_CAL_TYPE
43.9
RW
MAN
OOS
0: Not Calibrated
1: Single Point Calibration
2: Auto Calibration CAL
2: Auto Calibration
3: Manual Calibration
TRAVEL_TUNE
Data Type: Uint16

Raw feedback from Travel Sensor
44

TVL_INTEG_ENABLE
44.1
RW
MAN
OOS
1=Off
2=On
2=On
SETUP

TVL_INTEG_LIM_HI
44.2
RW
MAN
OOS
0% - 100%
30%
SETUP
Data Type: Float
RW
MAN
OOS
-100% - 0%
-30%
SETUP
Data Type: Float
0% - 2%
0.25%
SETUP
Data Type: Float
>=0
35
SETUP
Data Type: Float

TVL_INTEG_LIM_LO
44.3
Travel Integral Dead Zone

TVL_INTEG_DEADZ
44.4
RW
MAN
OOS
Travel MLFB Gain

TVL_MLFB_GAIN
44.5
RW
MAN
OOS
-Continued-
93
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
TRAVEL_CAL_RUN
Index
Number
RO /
RW
Mode
Range
Protect
Category
Description
45
Travel Calibration Command

TVL_CAL_CMD
45.1
RW
MAN
Travel Calibration Prog

TVL_CAL_PROG
45.2
RO
N/A
Travel Calibration Status

TVL_CAL_STATUS
45.3
Reserved
TVL_CAL_RESERVED
45.4
RO
N/A
1: Operating
2: Autocalibrate
3: Not Used by DVC6200f
4: Mark Full Open
5: Mark Full Closed
6: Manual Calibrate Final
7: Abort
8: Clear Cal Status
9: Manual Calibrate Init
10: Manual Calibrate
Restore
11: Reset Travel Sensor
Error
12: Reserved
1=Operating
13: Execute Performance
Tuner
Tuner (Graphite Packing)
Tuner (Booster)
Tuner (Graphite Packing
and Booster)
19: Autocalibration, Set
Filter
20: Autocalibrate
Extended, Set Filter
0%
0: auto cal complete
1: calibration complete
2: auto cal in progress
3: manual cal in progress
3: Not Used by DVC6200f
5: upper position marked
6: lower position marked
7: calibration error
8: Performance Tuner
active
no bits set
Success
Error (No movement)
Error (Accessories
unstable)
Error (Other)
CAL

Resets to 1 after a write
N/A
Data Type: Uint8
N/A
Data Type: Bit String (2 bytes)

All bits set to 0 when mode changes
from OOS. 0 = FALSE,
1 = TRUE
Reserved
-Continued-
94
Initial Value
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
PRESS_CAL
Index
Number
RO /
RW
Mode
Range
Initial Value
Protect
Category
Description
46
Supply Pressure Scale

SUPP_PRESS_SCALE
46.1
RW
MAN
OOS
>0
CAL
Data Type: Float
Supply Pressure Offset

SUPP_PRESS_OFFSET
46.2
RW
MAN
OOS
0 to 16383
CAL
Data Type: Uint16
Pressure A Scale
PRESS_A_SCALE
46.3
RW
MAN
OOS
>0
CAL
Data Type: Float
Pressure A Offset
PRESS_A_OFFSET
46.4
RW
MAN
OOS
0 to 16383
CAL
Data Type: Uint16
>0
CAL
Data Type: Float
CAL
Data Type: Uint16
Pressure B Scale
PRESS_B_SCALE
46.5
RW
MAN
OOS
Pressure B Offset
PRESS_B_OFFSET
46.6
RW
MAN
OOS
0 to 16383
Pressure IP Bias
PRESS_IP_BIAS
46.7
RW
MAN
OOS
0-100%
70%
CAL
Data Type: Float
Pressure MLFB Bias

PRESS_MLFB_BIAS
46.8
RW
MAN
OOS
0-100%
50%
CAL
Data Type: Float
RW
MAN
OOS
-25 -125%,
> CUTOFF_LO
99.50%
SETUP
Data Type: Float
-25 -125% < CUTOFF_HI
0.50%
SETUP
Data Type: Float

PRESS_TUNE
Pressure Cutoff Hi
PRESS_CUTOFF_HI
47
47.1
Pressure Cutoff Lo
PRESS_CUTOFF_LO
47.2
RW
MAN
OOS

PRESS_PROP_GAIN
47.3
RW
MAN
OOS
> = 0, < 32
2.2
SETUP
Data Type: Float

Proportional gain
Pressure Integral Gain

PRESS_INTEG_GAIN
47.4
RW
MAN
OOS
> = 0, < 32
0.1
SETUP
Data Type: Float

Integral resets per second
Pressure Rate Gain

PRESS_RATE_GAIN
47.5
RW
MAN
OOS
> = 0, < = 512
SETUP
Data Type: Float

Derivative gain
Pressure Integral Dead Zone

PRESS_INTEG_DEADZ
47.6
RW
MAN
OOS
= 0%, < = 2.0%
0.25%
SETUP
Data Type: Float

Integrator Deadzone, 1/2 width
Pressure Integral Limit Hi

PRESS_INTEG_HI_LIM
47.7
RW
MAN
OOS
> = 0%, < = 100%,

>INTEG_LO
20%
SETUP
Data Type: Float

Integrator limits
Pressure Integral Limit LO

PRESS_INTEG_LO_LIM
47.8
RW
MAN
OOS
< = 0%, > = -100%,

<INTEG_HI
-20%
SETUP
Data Type: Float

Integrator limits
Pressure Integral IC Hi
PRESS_INTEG_IC_HI
47.9
RW
MAN
OOS
>= -100%, < = 100%
12%
Not used by the DVC6200f
Pressure Integral IC Lo
PRESS_INTEG_IC_LO
47.10
RW
MAN
OOS
>= -100%, < = 100%
-12%
Pressure MLFB Gain

PRESS_MLFB_GAIN
47.11
RW
MAN
OOS
> 0, < = 100
35
SETUP
Data Type: Float
Temperature
TEMPERATURE
48
RO
N/A
N/A
N/A
Data Type: Float

Electronics temperature - Controls
AI channel 11
Target Travel
TRAVEL_TARGET
49
RO
Status
STATUS
49.1
RO
MAN
OOS
N/A
Value
VALUE
49.2
RO
MAN
OOS
N/A
RW
MAN
OOS
INPUT_CHAR
50
1=Linear
2=Equal %
3=Quick Opening
4=Reserved
5=Custom
1=Linear
SETUP
Data Type: DS65

In Travel Control: Setpoint for valve
travel in %, post characterization.
In Pressure Control: Setpoint for
implied valve travel as a % or
pressure range, post
characterization.
-Continued-
95
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Index
Number
RO /
RW
Mode
Protect
Category
0 to 100%
N/A
Data Type: Float

Absolute value of (TRAVEL_TARGET
[49] - TRAVEL [34]), Controls AI
channel 10
N/A
0 to 100%
N/A
Data Type: Float

Controls AI channel 9
RO
N/A
0 to 100%
N/A
Data Type: Float
RO
N/A
-100% to 100%
N/A
Data Type: Float
RW
MAN
OOS
Travel Deviation
TRAVEL_DEVIATION
52
RO
N/A
Drive Signal
DRIVE_SIGNAL
53
RO
Drive Current
DRIVE_CURRENT
54
MLFB
MLFB
55
Failed Alarm
FAILED_ALM
56
Linear, Y=X
Data Type: DS71

Used to report alerts to host system.
RW
ALL
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
NONE
0=Undefined
1=Clear-reported
3=Active-reported
0=Undefined
N/A
ALARM_STATE
56.2
RO
N/A
TIME_STAMP
56.3
RO
N/A
N/A
SUBCODE
56.4
RO
N/A
N/A
VALUE
56.5
RO
N/A
N/A
Maintenance Alarm
MAINT_ALM
57
UNACKNOWLEDGED
57.1
Data Type: Float

Value of parameter at alarm time for
single alarm, 0 for multiple alarms
Data Type: DS71
Used to report alerts to host system
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
NONE
0=Undefined
1=Clear-reported
3=Active-reported
0=Undefined
N/A
ALARM_STATE
57.2
RO
N/A
TIME_STAMP
57.3
RO
N/A
N/A
SUBCODE
57.4
RO
N/A
N/A
VALUE
57.5
RO
N/A
N/A
-Continued-
96
Description
SETUP
51
56.1
Initial Value
Data Type: Unit16 Array[43]

Each item - 2500 to 12500
First integrator is number of valid
points. Followed by up to 21 X
values and then 21 Y values.
X values must be increasing.
Y values must be increasing or same.
A value of 2050 represent 20.50%
Custom Points can be written only if
(INPUT_CHAR [50]) is not custom.
Custom Points
CUSTOM_POINTS
UNACKNOWLEDGED
Range
Data Type: Float

Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Advise Alarm
ADVISE_ALM
UNACKNOWLEDGED
Index
Number
RO /
RW
Mode
Range
Initial Value
Protect
Category
58
58.1
Description
Data Type: DS71
Used to report alerts to host system
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
NONE
0:Undefined
1:Clear-reported
2:Clear-not reported
3:Active-reported
4:Active-not reported
0=Undefined
N/A
ALARM_STATE
58.2
RO
N/A
TIME_STAMP
58.3
RO
N/A
N/A
SUBCODE
58.4
RO
N/A
N/A
VALUE
58.5
RO
N/A
N/A
Data Type: Float

N/A
0:Drive Current
1:Drive Signal
2:Processor Impaired
3:Output Block Timeout
4:Blocks Set to Defaults
5:Travel Sensor
6:Outlet Pressure Sensor
7:Supply Pressure
Sensor
8:Temperature Sensor
9:Supply Pressure
All bits: 0
10:Temperature Limit
11:Travel Deviation
12:Travel Limit
13:Travel Accumulator
14:Cycle Counter
15:Performance Critical
16:Performance
Reduced
17:Performance
Information
18: Shutdown Alert
N/A

0=inactive
1=active
Failed Alert Status
N/A
0:Drive Current
1:Drive Signal
5:Travel Sensor
7:Supply Pressure
Sensor
9:Supply Pressure
All bits: 0
11:Travel Deviation
12:Travel Limit
14:Cycle Counter
16:Performance
Reduced
17:Performance
Information
18: Shutdown Alert
N/A

0=inactive
1=active
Maintenance Alert Status
Failed Active
FAILED_ACTIVE
Maintenance Active
MAINT_ACTIVE
59
60
RO(1)
RO(1)
1. These parameters can be written when PWA_SIMULATE is active and Protect Category is not ALL.
-Continued-
97
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Advise Active
ADVISE_ACTIVE
Failed Enable
FAILED_ENABLE
Maintenance Enable
MAINT_ENABLE
Advise Enable
ADVISE_ENABLE
Failed Suppress
FAILED_MASK
Index
Number
61
62
63
64
65
RO /
RW
RO(1)
RW
RW
RW
RW
Mode
N/A
ALL
ALL
ALL
ALL
Range
0:Drive Current
1:Drive Signal
5:Travel Sensor
7:Supply Pressure
Sensor
9:Supply Pressure
All bits: 0
11:Travel Deviation
12:Travel Limit
14:Cycle Counter
16:Performance
Reduced
17:Performance
Information
18: Shutdown Alert
Same as for
FAILED_ACTIVE above
Enabled Bits:
0: Drive Current
2: Processor
Impaired
4: Blocks Set to
Default
5: Travel Sensor
15: Performance
Critical
18: Shutdown
Alert
Same as for
MAINT_ACTIVE above
Enabled Bits:
1: Drive Signal
3: Output Block
Timeout
6: Outlet Pressure
Sensor
9: Supply Pressure
11: Travel
Deviation
13: Travel
Accumulator
14: Cycle Counter
16: Performance
Reduced
Same as for
ADVISE_ENABLE above
Enabled Bits:
8: Temperature
Sensor
9: Supply Pressure
Sensor
10: Temperature
Limit
12: Travel Limit
Same as for
FAILED_ACTIVE above
-Continued-
98
Initial Value
All bits: 0
Protect
Category
Description
N/A

0=inactive
1=active
Advise Alert Status
ALL

0=disable
1=enable
Failed alert enable. Enable allows
detection of alert. All alerts can be
disabled.
ALL

0=disable
1=enable
Maintenance alert enable. Enable
allows detection of alert. All alerts
can be disabled.
ALL

0=disable
1=enable
Advise alert enable. Enable allows
detection of alert. All alerts can be
disabled.
ALL

0=disable
1=enable
Failed alert mask.
MASK controls whether an alert is
reported. If alert is enabled the alert
condition is evaluated and the
ACTIVE parameter is updated to
reflect if alert is active or not. If the
bit is set reporting is suppressed.
Default is all bits cleared.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Maintenance Suppress
MAINT_MASK
Index
Number
66
RO /
RW
RW
Mode
ALL
Range
Same as for
MAINT_ACTIVE above
Initial Value
All bits: 0
Protect
Category
Description
ALL

0=disable
1=enable
Maintenance alert mask. MASK
controls whether an alert is
reported. If alert is enabled the alert
condition is evaluated and the
ACTIVE parameter is updated to
reflect if alert is active or not. If the
bit is set reporting is suppressed.
Default is all bits cleared.
Advise Suppress
ADVISE_MASK
67
RW
ALL
Same as for
ADVISE_ENABLE above
All bits: 0
ALL

0=disable
1=enable
Advise alert mask. MASK controls
whether an alert is reported. If alert
is enabled the alert condition is
evaluated and the ACTIVE
parameter is updated to reflect if
alert is active or not. If the bit is set
reporting is suppressed. Default is all
bits cleared.
Failed Priority
FAILED_PRI
68
RW
ALL
0 to 15
SETUP
Data Type: Uint8

Failed alert priority
Maintenance Priority
MAINT_PRI
69
RW
ALL
0 to 15
SETUP
Data Type: Uint8

Maintenance alert priority
Advise Priority
ADVISE_PRI
70
RW
ALL
0 to 15
SETUP
Data Type: Uint8

Advise alert priority
Recommended Action
RECOMMENDED_ACTION
71
RO
N/A
0 to 65535
N/A
Data Type: Uint16

Fix for most serious condition
Travel Accumulator
TRAVEL_ACCUM
72
RW
ALL
Write:Anything
Read:Actual
CAL
Data Type: Uint32

Total travel expressed in integer %
terms. Controls AI channel 13.
ALL
Write:Anything
Read:Actual
CAL
Data Type: Uint32

Number of cycle transitions above a
certain threshold of movement.
Cycle Count
CYCLE_COUNT
73
RW
-Continued-
99
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME

INST_ALERTS_ACTIVE
Electronics Active
ELECT_ACTIVE
Index
Number
RO /
RW
Mode
Range
Protect
Category
Description
74
74.1
RO(1)
ALL
0:Drive Current
1:Drive Signal
2:Memory Failure Pending
3:Static Memory
4:Processor
5:I/O Processor
7:Block Set to Defaults
All bits: 0
N/A

0=inactive
1=active
Electronics Alert status
N/A

0=inactive
1=active
Sensor Alert status
N/A

0=inactive
1=active
Environment Alert status
Sensor Active
SENSOR_ACTIVE
74.2
RO(1)
ALL
0:Travel Sensor
1:Port A Pressure Sensor
2:Port B Pressure Sensor
3:Supply Pressure
All bits: 0
Sensor
5: Pressure Fallback
Environment Active
ENVIRO_ACTIVE
74.3
RO(1)
ALL
0:Supply Pressure High

1:Supply Pressure Low
2:Temperature High
3:Temperature Low
ALL
0:Travel Deviation
1:Travel High High
2:Travel Low Low
3:Travel High
4:Travel Low
All bits: 0
N/A

0=inactive
1=active
Travel Alert status
All bits: 0
N/A

0=inactive
1=active
Proximity Alert status.
Travel Active
TRAVEL_ACTIVE
74.4
RO(1)
All bits: 0
Proximity Active
PROX_ACTIVE
74.5
RO(1)
N/A
0:Travel Open
1:Travel Closed
2:Proximity High High
3:Proximity High
4:Proximity Low
5:Proximity Low Low
Travel History Active

TVL_HISTORY_ACTIVE
74.6
RO(1)
ALL
0:Cycle Counter
All bits: 0
N/A

0=inactive
1=active
Travel History Alert status
Performance Active
PERF_ACTIVE
74.7
RO(1)
ALL
1:Performance Reduced
2:Performance
Information
All bits: 0
N/A

0=inactive
1=active
Performance Diagnostic Alert status
ALL
0:High I/P Drive Signal

1:Low I/P Drive Signal
2:High Air Mass Flow
3:Large Travel Deviation
4:Low Supply Pressure
5:High Supply Pressure
6:High Crossover
Pressure
7:Low Crossover
Pressure
8: No Air Mass Flow
Estimate
N/A

0=inactive
1=active
Performance Diagnostic event
status.
PD Event Active
PD_EVENT_ACTIVE
74.8
RO(1)
-Continued-
100
Initial Value
All bits: 0
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
PD Detail 1 Active
PD_DETAIL1_ACTIVE
PD Detail 2 Active
PD_DETAIL2_ACTIVE
PD Detail 3 Active
PD_DETAIL3_ACTIVE
PD Detail 4 Active
PD_DETAIL4_ACTIVE
Index
Number
74.9
74.10
74.11
74.12
RO /
RW
RO(1)
RO(1)
RO(1)
RO(1)
Mode
ALL
Range
0:I/P Primary Plugged
1:I/P Nozzle Plugged
2:I/P Latched
3:Reserved
4:Relay Jammed
5:Relay Cross Misadj
6:Relay Bias Diaph Leak
7:Relay Port A Diaph
Leak
8:Relay Port B Diaph
Leak
9:Reserved
10:Valve Stuck Low or
Sensor Arm Damage
11:Valve Stuck High or
Sensor Arm Damage
12:Piston Ring Leak
13:Reserved
15:External Leak
16:SOV Trip
17:Air Line Blocked
18:Reserved
19:Reserved
20:Unknown
ALL
Reserved
ALL
0:I/P Primary Plugging

1:I/P Nozzle Plugging
2:I/P Calibration Shift
3:Reserved
4:Relay Cross Misadj
5:Relay Port A Diaph
Leak
6:Relay Port B Diaph
Leak
7:Reserved
8:Piston Ring Leak
9:Reserved
10:Reserved
12:Reserved
13:External Leak
14:Reserved
15:Travel Calibration
Shift
16:Unknown
17:Reserved
18:Reserved
ALL
Reserved
Initial Value
All bits:0
All bits: 0
All bits: 0
All bits: 0
Protect
Category
Description
N/A

0=inactive
1=active
Performance Diagnostic Critical
possible cause.
N/A

0=inactive
1=active
Performance Diagnostic Detail
status.
N/A

0=inactive
1=active
Performance Diagnostic Reduce
possible cause.
N/A

0=inactive
1=active
status
-Continued-
101
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
PD Detail 5 Active
PD_DETAIL5_ACTIVE
PD Detail 6 Active
PD_DETAIL6_ACTIVE
Shutdown Alerts
SHUTDOWN_ALERTS_ACTIVE
Index
Number
74.13
74.14
74.15
RO /
RW
RO(1)
RO(1)
RO
Mode
ALL
Range
0: Relay Disengaged
1: Insufficient Pressure
Differential
2: Travel Calibration Error
3: Reserved
4: High Supply Pressure*
5: Reserved
6: Near a Travel Cutoff Or
Stop
7:Reserved
8: Spec Sheet Fields
All bits: 0
Incomplete*
9: Sensor Failure*
10: Pressure Control
Active
11: Transducer Block
Mode OOS
12: Not Authorized for PD
13: PD Run Disabled*
14: Trigger Data
Available*
ALL
Reserved
N/A
0:Drive Current
1:Program Memory
2:Static Memory
3:Processor or I/O
Processor
All bits: 0
4:Travel Sensor
6: Output Block Timeout
7-31:(Reserved)
-Continued-
102
Initial Value
All bits: 0
Protect
Category
N/A
Description

0=inactive
1=active
status
*Bits which, when set, will trigger
PERF_ACTIVE bit 2.
N/A

0=inactive
1=active
status
N/A

0=inactive
1=active
Indicates what caused an Instrument
Shutdown. Bit remains set even if
condition has passed if Shutdown
Recovery is Manual. All bits are
cleared when MODE_BLK.TARGET is
written. Always enabled whenever
the corresponding
SHUTDOWN_TRIGGER is enabled.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
INST_ALERTS_ENABLE
Electronics Enable
ELECT_ENABLE
Sensor Enable
SENSOR_ENABLE
Environment Enable
ENVIRO_ENABLE
Travel Enable
TRAVEL_ENABLE
Index
Number
RO /
RW
Mode
Range
Initial Value
Protect
Category
Description
75
75.1
75.2
75.3
75.4
RW
RW
RW
RW
Enabled Bits:
0: Drive Current
1: Drive Signal
2: Program
Memory
3: Static Memory
4: Processor
5: I/O Processor
7: Block Set to
Default
ALL
0:Drive Current
1:Drive Signal
2:Program Memory
3:Static Memory
4:Processor
5:I/O Processor
SETUP

0=disable
1=enable
Electronic Alerts Enable
ALL
Enabled Bits:
0:Travel Sensor
1:Port A Pressure
0:Travel Sensor
1:Port A Pressure Sensor Sensor
2:Port B Pressure Sensor 2:Port B Pressure
SETUP
Sensor
3:Supply Pressure
3:Supply Pressure
Sensor
Sensor
4:Temperature
Sensor

0=disable
1=enable
Sensor Alerts Enable
ALL
0:Supply Pressure High

1:Supply Pressure Low
2:Temperature High
3:Temperature Low
Enabled Bits:
0:Supply Pressure
High
2:Temperature
SETUP
High
3:Temperature
Low

0=disable
1=enable
Environment Alerts Enable
ALL
0:Travel Deviation
1:Travel High High
2:Travel Low Low
3:Travel High
4:Travel Low
Enabled Bits:
0:Travel
Deviation
SETUP

0=disable
1=enable
Travel Alerts Enable
All bits: 0
SETUP

0=disable
1=enable
Proximity Alerts Enable
Proximity Enable
PROX_ENABLE
75.5
RW
ALL
0:Travel Open
1:Travel Closed
2:Proximity High High
3:Proximity High
4:Proximity Low
5:Proximity Low Low
Travel History Enable

TVL_HISTORY_ENABLE
75.6
RW
ALL
0:Cycle Counter
All bits: 0
SETUP

0=disable
1=enable
Travel History Alerts Enable
ALL
1:Performance Reduced
2:Performance
Information
Enabled Bits:
0:Performance
Critical
1:Performance
Reduced
SETUP

0=disable
1=enable
Performance Alerts Enable
Performance Enable
PERF_ENABLE
75.7
RW
-Continued-
103
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
INST_ALERTS_CONFIG
Shutdown Trigger
SHUTDOWN_TRIGGER
Index
Number
RO /
RW
Mode
Range
Protect
Category
Description
76
76.1
RW
ALL
0:Drive Current
1:Program Memory
2:Static Memory
3:Processor or I/O
Processor
All bits: 0
4:Travel Sensor
7-31:(Reserved)
SETUP

0=Auto
1=Manual
Recovery action after a shutdown
trigger fail to zero drive above,
SETUP

0=attempt control,
1=fail to zero drive e.g. OOS mode
Action on specific instrument alerts:
Shutdown Recovery
SHUTDOWN_RECOVERY
76.2
RW
ALL
0:(reserved)
1:Program Memory
2:Static Memory
3:Processor or I/O
Processor
All bits: 0
4:Travel Sensor
7-31:(Reserved)
Output Blk Timeout

OUTPUT_BLK_TIMEOUT
76.3
RW
ALL
Time > = 0, < = 800

seconds
600 sec
SETUP
Data Type: Float

The maximum time between
updates from the AO or DO block to
the transducer block setpoint.
Drive Current Alert Point

DRIVE_CURRENT_ALRT_PT
76.4
RW
ALL
> = 5, < = 100
25%
SETUP
Data Type: Float

(percent different) drive signal not
reaching I/P accurately.
Drive Current Alert Time

DRIVE_CURRENT_TIME
76.5
RW
ALL
= 0.25, < = 120 seconds
5 sec
SETUP
Data Type: Float

(percent different) drive signal not
reaching I/P accurately.
Temperature Hi Alert Point

TEMP_HI_ALRT_PT
76.6
RW
ALL
> -76 F, < 257 F
186 deg F
SETUP
Data Type: Float

Temperature HI Limits
Temperature Lo Alert Point

TEMP_LO_ALRT_PT
76.7
RW
ALL
> -76 F, < 257 F
-63 deg F
SETUP
Data Type: Float

Temperature LO Limits
Supply Pressure Hi Alert Point

SUP_PRES_HI_ALRT_PT
76.8
RW
ALL
> = 0, < = 150
145 psig
SETUP
Data Type: Float

Maximum supply pressure
Supply Pressure Lo Alert Point

SUP_PRES_LO_ALRT_PT
76.9
RW
ALL
> = 0, < = 150
15 psig
SETUP
Data Type: Float

Minimum supply pressure
INST_ALERTS_CONFIG2
77
Travel Deviation Alert Point

TVL_DEV_ALRT_PT
77.1
RW
ALL
> 0%, <= 125%
5%
SETUP
Data Type: Float

Alerts when difference between sp
and pv is too large for too long.
Travel Deviation Time

TVL_DEV_TIME
77.2
RW
ALL
> = 0, < = 120 seconds
10 sec
SETUP
Data Type: Float
Travel Deviation Deadband

TVL_DEV_DB
77.3
RW
ALL
> = 0%, < = 100%
2%
SETUP
Data Type: Float
Travel Accumulator Alert Point

TVL_ACCUM_ALRT_PT
77.4
RW
ALL
>=0
1,000,000
SETUP
Data Type: Uint32

Alerts when accumulated travel is
too much
Travel Accumulator Deadband

TVL_ACCUM_DB
77.5
RW
ALL
0 - 100%
1%
SETUP
Data Type: Float

Deadband
Cycle Count Alert Point

CYCLE_COUNT_ALRT_PT
77.6
RW
ALL
>=0
1,000,000
SETUP
Alerts when number of cycles is too

large.
Cycle Count Deadband

CYCLE_COUNT_DB
77.7
RW
ALL
0 - 100%
1%
SETUP
Data Type: Float

Deadband
-Continued-
104
Initial Value
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Index
Number
RO /
RW
Mode
Range
Initial Value
Protect
Category
Description
Travel Open Alert Point

TVL_OPEN_ALRT_PT
77.8
RW
ALL
-25% to 125%
99.5%
SETUP
Data Type: Float

Alert when valve is open. Control DI
channel 24 regardless of alert enable
state.
Travel Open Deadband

TVL_OPEN_DB
77.9
RW
ALL
> = 0%, < =100%
1%
SETUP
Data Type: Float

Deadband
Travel Closed Alert Point

TVL_CLOSED_ALRT_PT
77.10
RW
ALL
-25% to 125%
0.5%
SETUP
Data Type: Float

Alerts when valve closed. Controls DI
channel 25 regardless of alert enable
state.
Travel Closed Deadband

TVL_CLOSED_DB
77.11
RW
ALL
> = 0%, < = 100%
1%
SETUP
Data Type: Float

Deadband
Travel Lo Lo Alert Point

TVL_LO_LO_ALRT_PT
77.12
RW
ALL
-25% to 125%
-25%
SETUP
Data Type: Float

Alert when valve position is less than
alert point. Controls DI channels 26
& 30 regardless of alert enable state.
Travel Lo Lo Deadband
TVL_LO_LO_DB
77.13
RW
ALL
> = 0%, < = 100%
5%
SETUP
Data Type: Float

Deadband
Travel Lo Alert Point

TVL_LO_ALRT_PT
77.14
RW
ALL
-25% to 125%
-25%
SETUP
Data Type: Float

Travel Lo Deadband
TVL_LO_DB
77.15
RW
ALL
> = 0%, < = 100%
5%
SETUP
Data Type: Float

Deadband
Travel Hi Alert Point

TVL_HI_ALRT_PT
77.16
RW
ALL
-25% to 125%
125%
SETUP
Data Type: Float

Travel Hi Deadband
TVL_HI_DB
77.17
RW
ALL
> = 0%, < = 100%
5%
SETUP
Data Type: Float

Deadband
Travel Hi Hi Alert Point

TVL_HI_HI_ALRT_PT
77.18
RW
ALL
-25% to 125%
125%
SETUP
Data Type: Float

Travel Hi Hi Deadband
TVL_HI_HI_DB
77.19
RW
ALL
> = 0%, < = 100%
5%
SETUP
Data Type: Float

Deadband
-Continued-
105
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Index
RO /
Number RW
78
RO
Mode
N/A
Range
Initial Value
Protect
Category
0:
All bits: 0
2: Integrator Limited Low
3: Integrator Limited
High
4: Travel Sensor Span
Error
5: MLFB Error
7: Travel Sensor High
Error
8: Travel Sensor Low Error
9: Pressure Sensor B
10: Pressure Sensor A
11: Supply Pressure
Sensor
13: IOP Failure
14: Drive Current
15: Simulate Jumper ON
Description
Self Test Status

SELFTEST_STATUS

0=inactive
1=active
Indicates the status of the
instrument self test.
Integrator Limited Low: Indicates
the integrator reached its limit and
cannot move the valve any further.
High valve friction may cause this
situation.
Integrator Limited High:
Indicates the integrator reached its
limit and cannot move the valve any
further. High valve friction may
cause this situation.
Travel Sensor Span Error:
Indicates that span between the
endpoints of travel are not far
enough apart. This error is reported
during automatic calibration.
MLFB Error: Indicates that the Minor
Loop Feedback sensor gave a
nonvalid value during automatic
calibration.
Travel Sensor High Error:
Indicates the travel sensor has
reported a travel position that is
significantly above the normal
operating range, and has failed.
Travel Sensor Low Error: Indicates
the travel sensor has reported a
travel position that is significantly
below the normal operating range,
and has failed.
Pressure B Sensor Failure:
Indicates the pressure sensor is
reporting a pressure that is
significantly outside of the normal
operating pressure, and has failed.
Pressure A Sensor Failure:
Supply Sensor Failure:
IOP Failure: Indicates the I/O
processor has failed.
Drive Current: Indicates that the
Drive Current has exceeded the
Drive Current Alert Point for more
than the Drive Current Alert Time.
Simulate Jumper ON: Indicates the
simulate jumper is connected to the
DVC6200f between the two AUX
terminals.
Health Index
HEALTH_INDEX
79
RO
N/A
Reserved A
RESERVED_A
80
RW
ALL
0 - 100
-Continued-
106
100
N/A
Data Type: Uint8

Represents overall health of device.
100 is perfect, 0 is completely bad.
Settings for DVC6200f will range
from 10 to 100.
N/A
SETUP
Data Type: Array, 118 x Unit8

Reserved
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Reserved AI
RESERVED_AI
Upgrade Progress
UPGRADE_PROGRESS
SPEC_SHEET_VALVE
Index
Number
RO /
RW
Mode
Range
Initial Value
Protect
Category
Description
81
RW
ALL
SETUP
Data Type: Uint16

Reserved
82
RO
N/A
N/A

83
Valve Size
VALVE_SIZE
83.1
RW
ALL
NULL
ALL
Valve Class
VALVE_CLASS
83.2
RW
ALL
NULL
ALL
Rated Travel
RATEDTRAVEL
83.3
RW
ALL
0.00
ALL
Data Type: Float
Actual Travel
ACTUAL_TRAVEL
83.4
RW
ALL
0.00
ALL
Data Type: Float
Shaft Stem Diameter

SHAFT_STEM_DIA
83.5
RW
ALL
0.00
ALL
Data Type: Float
Packing Type
PACKING_TYPE
83.6
RW
ALL
NULL
ALL
Inlet Pressure
INLET_PRESSURE
83.7
RW
ALL
0.00
ALL
Data Type: Float
Outlet Pressure
OUTLET_PRESSURE
83.8
RW
ALL
0.00
ALL
Data Type: Float
RW
ALL
NULL
ALL
1= I
ALL
SPEC_SHEET_TRIM
Seat Type
SEAT_TYPE
84
84.1
Leak Class
LEAK_CLASS
84.2
RW
ALL
Port Diameter
PORT_DIAMETER
84.3
RW
ALL
ANSI Seat Leakage

Classification
1: I
2: II
3: III
4: IV
5: V
6: VI
7: BFW
8: STD AIR
9: BFW II
10: BFW III
11: BFW IV
12: BFW V
13: BFW VI
14: 1/10th of IV
15: Bubble Tight
0.00
ALL
Data Type: Float
ALL
1=balanced
2=unbalanced
ALL
RW
ALL
1=up
2=down
ALL
84.6
RW
ALL
1=open
2=close
ALL
Flow Tends To
FLOW_TENDS_TO
84.7
RW
ALL
1=open
2=close
ALL
Unbalanced Area
UNBALANCED_AREA
84.8
RW
ALL
0.00
ALL
Data Type: Float
Trim Style 1
TRIM_STYLE_1
84.9
RW
ALL
NULL
ALL
Trim Style 2
TRIM_STYLE_2
84.10
RW
ALL
NULL
ALL
Port Type
PORT_TYPE
84.4
RW
Flow Direction
FLOWDIRECTION
84.5
Push Down To
PUSH_DOWN_TO
-Continued-
107
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
SPEC_SHEET_ACT
Index
Number
RO /
RW
Mode
Range
Protect
Category
Description
85
Actuator Size
ACTUATOR SIZE
85.1
RW
ALL
NULL
ALL
Effective Area
EFFECTIVE AREA
85.2
RW
ALL
0.00
ALL
Data Type: Float
Air
AIR
85.3
RW
ALL
ALL
Lower Bench Set

LOWER_BENCH_SET
85.4
RW
ALL
0.00
ALL
Data Type: Float
Upper Bench Set

UPPER_BENCH_SET
85.5
RW
ALL
0.00
ALL
Data Type: Float
Nominal Supply Pressure

NOMINAL_SUPPLY_PRESSURE
85.6
RW
ALL
0.00
ALL
Data Type: Float
Spring Rate
SPRING_RATE
85.7
RW
ALL
0.00
ALL
Data Type: Float
Stroking Time Open

STROKING_TIME_OPEN
85.8
RW
ALL
0.00
ALL
Data Type: Float

Seconds
Stroking Time Close

STROKING_TIME_CLOSE
85.9
RW
ALL
0.00
ALL
Data Type: Float

Seconds
Lever Style
LEVER_STYLE
85.10
RW
ALL
ALL
Lever Arm Length

MOMENT_ARM
85.11
RW
ALL
0.00
ALL
Data Type: Float
DEVICE_RECORD
1=open
2=close
1=Pivot Point
2=Rack & Pinion
These parameters can only reset

through VL/DD.
86
Temperature Maximum
TEMP_MAX
86.1
RO
N/A
-9999.99
N/A
Data Type: Float

Highest temperature recorded
Temperature Maximum Time

TEMP_MAX_TIME
86.2
RO
N/A
Zero time
N/A
Data Type: Time Value
Temperature Minimum
TEMP_MIN
86.3
RO
N/A
9999.99
N/A
Data Type: Float

Lowest temperature recorded
Temperature Minimum Time

TEMP_MIN_TIME
86.4
RO
N/A
Zero time
N/A
Supply Pressure Maximum

SUPP_PRESS_MAX
86.5
RO
N/A
0.0
N/A
Data Type: Float

Highest supply pressure recorded
Supply Pressure Maximum Time

SUPP_PRESS_MAX_TIME
86.6
RO
N/A
Zero time
N/A
Supply Pressure Minimum

SUPP_PRESS_MIN
86.7
RO
N/A
9999.99
N/A
Data Type: Float

Lowest supply pressure recorded
Supply Pressure Minimum Time

SUPP_PRESS_MIN_TIME
86.8
RO
N/A
Zero time
N/A
Comm Error Count

COMM_ERROR_COUNT
86.9
RW
N/A
SETUP
NONE
Data Type: Enum

Write lock enable/disable. If setting
is at or above a parameters
protection level then that parameter
is readonly.
Protection
PROTECTION
87
RW
ALL
1=None
2=Calibration
3=Setup & Calibration
4=All
-Continued-
108
Initial Value
2=Calibration
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
PERF_DIAG
Index
Number
RO /
RW
Mode
Range
Initial Value
Protect
Category
Description
88
PD Run
PD_COMMAND
88.1
RW
AUTO
MAN
1=PD On
2=PD Off
NONE
Data Type: Enum

Controls whether PD will run or not.
PD Status
PD_STATUS
88.2
RO
ALL
1=Not Running
2=Running
NONE
Data Type: Enum

Status of performance diagnostics.
PD Configuration
PD_CONFIG
88.3
RW
ALL
NONE

Bit string for configuring PD setup
and options.
PD Extra
PD_EXTRA
88.4
RW
ALL
NONE
Data Type: Uint32

Extra 32 bit integer for sending
values to PD.
Temperature Units
TEMPERATURE_UNITS
89
RW
ALL
C=1001
F=1002
SETUP
kPa
SETUP
1=PD On
Pressure Units
PRESSURE_UNITS
90
RW
ALL
kPa=1133
bar=1137
psig=1143
inHg=1155
inH2O=1146
Kg/cm2=1145
Travel Units
TVL_UNITS
91
RW
ALL
cm=1012
mm=1013
in=1019
deg=1005
mm
SETUP

Travel units for spec sheet
ACTUAL_TRAVEL and RATEDTRAVEL
only.
Length Units
LENGTH_UNITS
92
RW
ALL
cm=1012
mm=1013
in=1019
mm
SETUP

Not used for spec sheet
ACTUAL_TRAVEL OR RATEDTRAVEL
Area Units
AREA_UNITS
93
RW
ALL
cm2=1025
mm2=1027
in2=1030
cm2
SETUP
Spring Rate Units

SPRING_RATE_UNITS
94
RW
ALL
N/m=1165
lb/in=1596
N/m
SETUP
MAI_CHANNEL_MAP
95
MAI Channel 1
MAI_CHANNEL_1
95.1
RW
MAN,
OOS
1 through 13
SETUP
MAI Channel 2
MAI_CHANNEL_2
95.2
RW
MAN,
OOS
1 through 13
SETUP
MAI Channel 3
MAI_CHANNEL_3
95.3
RW
MAN,
OOS
1 through 13
SETUP
MAI Channel 4
MAI_CHANNEL_4
95.4
RW
MAN,
OOS
1 through 13
SETUP
MAI Channel 5
MAI_CHANNEL_5
95.5
RW
MAN,
OOS
1 through 13
SETUP
MAI Channel 6
MAI_CHANNEL_6
95.6
RW
MAN,
OOS
1 through 13
SETUP
MAI Channel 7
MAI_CHANNEL_7
95.7
RW
MAN,
OOS
1 through 13
SETUP
MAI Channel 8
MAI_CHANNEL_8
95.8
RW
MAN,
OOS
1 through 13
SETUP
RW
MAN,
OOS
1: AO Block
2: DO Block
Output Block Selection

OUTBLOCK_SEL
PlantWeb Alerts Set PV Status

PWA_SET_STATUS
96
97
RW
MAN,
OOS
1: No
2: Yes
1: AO Block
1: No
Data Type:Uint16 This defines

which transducer block channels will
be sent to each of the 8 MAI
channels. No scaling or other
conversion will be done. Values will
be sent in the currently defined
units. If set to 0, then no output to
MAI (status will be set to BAD).
1=FINAL_VALUE
2=TRAVEL_TARGET
3=FINAL_POSITION_VALUE
4=TRAVEL
5=SUPPLY_PRESS
6=ACT_PRESS_A
7=ACT_PRESS_B
8=ACT_PRESS_DIFF
9=DRIVE_SIGNAL
10=TRAVEL_DEVIATION
11=TEMPERATURE
12=CYCLE_COUNT
13=TRAVEL_ACCUM
SETUP

Controls which output block (AO or
DO) the transducer block will
respond to.
SETUP

Controls whether the status of the
PV fed back to the output block from
the transducer block will be affected
by an active PlantWeb alert.
-Continued-
109
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Index
Number
RO /
RW
Mode
Range
Initial Value
Protect
Category
Bit 0: Travel feedback

sensor detected
Bit 1: Output Block
Scheduled
Bit 2: Trigger Capturing
Bit 3: Output Block in
Normal Mode
Bit 4: Write Lock is on
Bit 5: Resource Block in
Auto Mode
Description
Block Information
BLOCK_INFO
98
RO
Reserved B
RESERVED_B
99
RW
Travel Always
TRAVEL_ALWAYS
100
RO
Data Type: DS-65
View Lists
Table 415. Transducer Block, View 1
Index Number
1
Parameter
ST_REV
Table 416. Transducer Block, View 2

Index Number
ST_REV
TRANSDUCER_TYPE
5.1
MODE_BLK.TARGET
10
5.2
MODE_BLK.ACTUAL
14.1
FINAL_VALUE_RANGE.EU_100
5.3
MODE_BLK.PERMITTED
14.2
FINAL_VALUE_RANGE.EU_0
5.4
MODE_BLK.NORMAL
14.3
FINAL_VALUE_RANGE.UNITS_INDEX
BLOCK_ERR
14.4
FINAL_VALUE_RANGE.DECIMAL
10
TRANSDUCER_TYPE
11
XD_ERROR
13.1
FINAL_VALUE.STATUS
13.2
FINAL_VALUE.VALUE
17.1
FINAL_POSITION_VALUE.STATUS
17.2
FINAL_POSITION_VALUE.VALUE
32.1
SETPOINT_D.STATUS
32.2
SETPOINT_D.VALUE
15
FINAL_VALUE_CUTOFF_HI
16
FINAL_VALUE_CUTOFF_LO
18
SERVO_GAIN
19
SERVO_RESET
20
SERVO_RATE
21
ACT_FAIL_ACTION
40.1
GRANT_DENY.GRANT
40.2
GRANT_DENY.DENY
50
110
Parameter
INPUT_CHAR
Instruction Manual
D103412X012
August 2012
Note
Because individual views are limited in size, View Lists 3 and 4 have multiple parts.
Table 417. Transducer Block, View 3.1

Index Number
1
Parameter
ST_REV

Index Number
1
Parameter
ST_REV
5.1
MODE_BLOCK.TARGET
74.1
INST_ALERTS_ACTIVE.ELECT_ACTIVE
5.2
MODE_BLOCK.ACTUAL
74.2
INST_ALERTS_ACTIVE.SENSOR_ACTIVE
5.3
MODE_BLOCK.PERMITTED
74.3
INST_ALERTS_ACTIVE.ENVIRO_ACTIVE
5.4
MODE_BLOCK.NORMAL
74.4
INST_ALERTS_ACTIVE.TRAVEL_ACTIVE
BLOCK_ERR
74.5
INST_ALERTS_ACTIVE.PROX_ACTIVE
10
TRANSDUCER_TYPE
74.6
INST_ALERTS_ACTIVE.TVL_HISTORY_ACTIVE
11
XD_ERROR
74.7
INST_ALERTS_ACTIVE.PERF_ACTIVE
13.1
FINAL_VALUE.STATUS
74.8
INST_ALERTS_ACTIVE.PD_EVENT_ACTIVE
13.2
FINAL_VALUE.VALUE
74.9
INST_ALERTS_ACTIVE.PD_DETAIL1_ACTIVE
17.1
FINAL_POSITION_VALUE.STATUS
74.10
17.2
FINAL_POSITION_VALUE.VALUE
74.11
32.1
SETPOINT_D.STATUS
74.12
32.2
SETPOINT_D.VALUE
74.13
35.1
SUPPLY_PRESSURE.STATUS
78
SELFTEST_STATUS
35.2
SUPPLY_PRESSURE.VALUE
79
HEALTH_INDEX
36.1
PRESSURE_A.STATUS
86.1
DEVICE_RECORD.TEMP_MAX
36.2
PRESSURE_A.VALUE
86.2
DEVICE_RECORD.TEMP_MAX_TIME
37.1
PRESSURE_B.STATUS
86.3
DEVICE_RECORD.TEMP_MIN
37.2
PRESSURE_B.VALUE
86.4
DEVICE_RECORD.TEMP_MIN_TIME
38.1
PRESSURE_DIFF.STATUS
86.5
DEVICE_RECORD.SUPP_PRESS_MAX
38.2
PRESSURE_DIFF.VALUE
86.6
DEVICE_RECORD.SUPP_PRESS_MAX_TIME
48
TEMPERATURE
86.7
DEVICE_RECORD.SUPP_PRESS_MIN
49
TRAVEL_TARGET
86.8
DEVICE_RECORD.SUPP_PRESS_MIN_TIME
52
TRAVEL_DEVIATION
53
DRIVE_SIGNAL
54
DRIVE_CURRENT
55
MLFB
Index Number
59
FAILED_ACTIVE
ST_REV
60
MAINT_ACTIVE
STRATEGY
61
ADVISE_ACTIVE
ALERT_KEY
71
RECOMMEND_ACTION
10
TRANSDUCER_TYPE
72
TRAVEL_ACCUM
22
ACT_MAN_ID
73
CYCLE_COUNT
23
ACT_MODEL_NUM
75.1
INST_ALERTS_ENABLE.ELECT_ENABLE
24
ACT_SN
75.2
INST_ALERTS_ENABLE.SENSOR_ENABLE
25
VALVE_MAN_ID
75.3
INST_ALERTS_ENABLE.ENVIRO_ENABLE
26
VALVE_MODEL_NUM
75.4
INST_ALERTS_ENABLE.TRAVEL_ENABLE
75.5
INST_ALERTS_ENABLE.PROX_ENABLE
75.6
INST_ALERTS_ENABLE.TVL_HISTORY_ENABLE
75.7
INST_ALERTS_ENABLE.PERF_ENABLE
Parameter
111
Instruction Manual

August 2012
D103412X012
Table 421. Transducer Block, View 4.3 (continued)
Index Number
Index Number
Parameter
ST_REV
67
ADVISE_MASK
27
VALVE_SN
68
FAILED_PRI
28
VALVE_TYPE
69
MAINT_PRI
29
XD_CAL_LOC
70
ADVISE_PRI
30
XD_CAL_DATE
31
XD_CAL_WHO
89
TEMPERATURE_UNITS
90
PRESSURE_UNITS
91
TVL_UNITS
92
LENGTH_UNITS
93
AREA_UNITS
94
SPRING_RATE_UNITS
Index Number
Parameter
ST_REV
39
PWA_SIMULATE
Index Number
1
41.1
TVL_PRESS_CONTROL.TVL_PRESS_SELECT
41.2
TVL_PRESS_CONTROL.TVL_PRESS_STATE
42.1
BASIC_SETUP.ACTUATOR_STYLE
42.2
BASIC_SETUP.ZERO_PWR_COND
42.3
BASIC_SETUP.TRAVEL_SEN_MOTION
42.4
BASIC_SETUP.FEEDBACK_CONN
42.5
BASIC_SETUP.RELAY_TYPE
42.6
BASIC_SETUP.MAX_SUPP_PRESS
42.7
BASIC_SETUP.PRESS_RANGE_HI
42.8
BASIC_SETUP.PRESS_RANGE_LO
Parameter
ST_REV
76.1
INST_ALERTS_CONFIG.SHUTDOWN_TRIGGER
76.2
INST_ALERTS_CONFIG.SHUTDOWN_RECOVERY
76.3
INST_ALERTS_CONFIG.OUTPUT_BLK_TIMEOUT
76.4
INST_ALERTS_CONFIG.DRIVE_CURRENT_ALRT_PT
76.5
INST_ALERTS_CONFIG.DRIVE_CURRENT_TIME
76.6
INST_ALERTS_CONFIG.TEMP_HI_ALRT_PT
76.7
INST_ALERTS_CONFIG.TEMP_LO_ALRT_PT
76.8
INST_ALERTS_CONFIG.SUP_PRES_HI_ALRT_PT
76.9
INST_ALERTS_CONFIG.SUP_PRES_LO_ALRT_PT
77.1
INST_ALERTS_CONFIG2.TVL_DEV_ALRT_PT
77.2
INST_ALERTS_CONFIG2.TVL_DEV_TIME
77.3
INST_ALERTS_CONFIG2.TVL_DEV_DB
77.4
INST_ALERTS_CONFIG2.TVL_ACCUM_ALRT_PT
77.5
INST_ALERTS_CONFIG2.TVL_ACCUM_DB
77.6
INST_ALERTS_CONFIG2.CYCLE_COUNT_ALRT_PT
77.7
INST_ALERTS_CONFIG2.CYCLE_COUNT_DB
77.8
INST_ALERTS_CONFIG2.TVL_OPEN_ALRT_PT
77.9
INST_ALERTS_CONFIG2.TVL_OPEN_DB
77.10
INST_ALERTS_CONFIG2.TVL_CLOSED_ALRT_PT
77.11
INST_ALERTS_CONFIG2.TVL_CLOSED_DB
77.12
INST_ALERTS_CONFIG2.TVL_LO_LO_ALRT_PT
77.13
INST_ALERTS_CONFIG2.TVL_LO_LO_DB
77.14
INST_ALERTS_CONFIG2.TVL_LO_ALRT_PT
77.15
INST_ALERTS_CONFIG2.TVL_LO_DB
77.16
INST_ALERTS_CONFIG2.TVL_HI_ALRT_PT
77.17
INST_ALERTS_CONFIG2.TVL_HI_DB
77.18
INST_ALERTS_CONFIG2.TVL_HI_HI_ALRT_PT
77.19
INST_ALERTS_CONFIG2.TVL_HI_HI_DB
42.9
BASIC_SETUP.TVL_CAL_TRIGGER
42.10
BASIC_SETUP.TVL_TUNING_SET
42.11
BASIC_SETUP.PRESS_TUNING_SET
44.1
TRAVEL_TUNE.TVL_INTEG_ENABLE
44.2
TRAVEL_TUNE.TVL_INTEG_LIM_HI
44.3
TRAVEL_TUNE.TVL_INTEG_LIM_LO
44.4
TRAVEL_TUNE.TVL_INTEG_DEADZ
44.5
TRAVEL_TUNE.TVL_MLFB_GAIN
47.1
PRESS_TUNE.PRESS_CUTOFF_HI
47.2
PRESS_TUNE.PRESS_CUTOFF_LO
47.3
PRESS_TUNE.PRESS_PROP_GAIN
47.4
PRESS_TUNE.PRESS_INTEG_GAIN
47.5
PRESS_TUNE.PRESS_RATE_GAIN
Table 423. Transducer Block View, 4.5
47.6
PRESS_TUNE.PRESS_INTEG_DEADZ
Index Number
47.7
PRESS_TUNE.PRESS_INTEG_HI_LIM
47.8
PRESS_TUNE.PRESS_INTEG_LO_LIM
95.1
MAI_CHANNEL_1
47.9
PRESS_TUNE.PRESS_INTEG_IC_HI
95.2
MAI_CHANNEL_2
47.10
PRESS_TUNE.PRESS_INTEG_IC_LO
95.3
MAI_CHANNEL_3
47.11
PRESS_TUNE.PRESS_MLFB_GAIN
95.4
MAI_CHANNEL_4
62
FAILED_ENABLE
95.5
MAI_CHANNEL_5
63
MAINT_ENABLE
95.6
MAI_CHANNEL_6
64
ADVISE_ENABLE
95.7
MAI_CHANNEL_7
65
FAILED_MASK
95.8
MAI_CHANNEL_8
66
MAINT_MASK
96
OUTBLOCK_SEL
97
PWA_SET_STATUS
-continued-
112
Parameter
82
UPGRADE_PROGRESS
87
PROTECTION
Parameter
ST_REV
Instruction Manual
Detailed SetupAO Function Block
D103412X012
August 2012
Analog Output Function Block

Overview
The Analog Output (AO) function block (figure 46) assigns an output value to a field device through a specified I/O
channel. The block supports mode control, signal status calculation, and simulation. Figure 47 illustrates the internal
components of the AO function block, and table 425 lists the definitions of the block parameters. The digital valve
controller measures and uses actual valve position for READBACK [16].
Figure 46. Analog Output (AO) Function Block
BKCALOUT
CAS IN
AO
OUT
READBACK
CASIN = The remote setpoint value from another

function block.
BKCALOUT = The value and status required by the
BKCALIN input of another block to prevent reset
windup and to provide bumpless transfer to closed
loop control.
OUT = The block output and status.
B27161
READBACK = Actual valve position.
Note
The AO block actual mode will not move to Auto unless:
Resource Block actual mode is Auto, and
AO SHED_OPT [27] is set to a nonzero value.
Note
Actual Block Mode (MODE_BLK.ACTUAL [5.2]) will remain out of service and the block cannot be scheduled if the block has not
been licensed. Contact your Emerson Process Management sales office to upgrade product licensing.
Note
Actual Block Mode (MODE_BLK.ACTUAL [5.2]) will remain in IMAN and the block Readback status will be Bad - Not Connected if
the Output Block Selection is set incorrectly. From the transducer block method Outblock Selection, select the desired output
block, see page 69.
113
Instruction Manual

August 2012
D103412X012
Figure 47. Analog Output Function Block Schematic

RCASOUT
RCASIN
Operator
Setpoint
CASIN
SP
HI/LO
Limit
BKCALOUT
READBACK
PV
SPRATEDN
SPRATEUP
Convert
and Status
Calculation
SP
Rate
Limit
OUT
SPWRK
SPLOWLIM
SPHILIM
PVSCALE
IOOPTS
MODE
Shed
Mode
Access
Analog
Input
B2717
Position
Feedback
Access
Analog
Output
CHANNEL
Analog
Output
Modes
The Analog Output function block supports the following modes:
Manual (Man)You can manually set the output to the I/O channel through the OUT [9] attribute. This mode is used
primarily for maintenance, calibration and diagnostics.
Automatic (Auto)The block output (OUT [9]) reflects the target operating point specified by the setpoint (SP [8])
attribute. Typically the setpoint is set by the user.
Cascade (Cas)The SP [8] attribute is set by another function block through a connection to CAS_IN [17]. The SP [8]
value is used to set the OUT [9] attribute automatically. This is the most frequently used mode in the digital valve
controller.
Note
The transducer block must be in Auto for the mode to go to AUTO, CAS, MAN, or RCAS.
RemoteCascade (RCas)The SP [8] is set by a host computer by writing to the RCAS_IN [28] parameter. The SP [8]
value is used to set the OUT [9] attribute automatically.
114
Instruction Manual
D103412X012
August 2012
Out of Service (OOS)The block is not processed. The output channel is maintained at the last value and the status
of OUT [9] is set to Bad: Out of Service. The BLOCK_ERR [6] attribute shows Out of Service.
Initialization Manual (Iman)The path to the output hardware is broken and the AO block output will remain at the
last position. This means the transducer block mode is Out of Service or Manual or configured to respond to the DO
block.
Local Override (LO)The output of the block is not responding to inputs because the fault state action is active. OUT
[9] freezes or goes to value per IO_OPTS [14].
The target mode of the block may be restricted to one or more of the following modes: Man, Auto, Cas, RCas, or OOS.
Mode Handling
Shed OptionsRCAS Mode Only
Automatically changing through the permitted modes when starting from a remote mode, fall from (or shed) or climb
to a remote mode is determined by the parameter SHED_OPT [27]. A block climbs and sheds through the same path.
For example, if SHED_OPT [27] specifies that a block should shed to Auto, then, if the block target mode is set to RCas,
the block goes through Auto on the way to RCas.
When the block is in Cas mode and the CAS_IN [17] input goes bad, the block sheds mode to the next lower permitted
mode.
You can configure the shed option as follows:
Shed With Return Options

Remote cascade connection failure shifts actual mode but keeps trying to restore remote cascade (in other words, the
remote cascade target mode stays in effect).
Note
During Shed with Return Options, the actual mode is changed, while the target mode stays the same.
NormalOn failure of a remote cascade connection the block attempts to attain the highest permitted nonremote
mode until remote cascade is restored. Cas is the highest permitted nonremote mode and Auto is is the next
permitted nonremote mode. If Cas or Auto are not available, the block will shed by default to Man.
Retained TargetThe retained target mode is the previous target mode before it was changed to RCAS or ROUT. On
failure of a remote cascade connection the block attempts to attain the retained target mode.
AutoOn failure of a remote cascade connection the block attempts to attain Auto, if permitted, until remote cascade
is restored.
ManOn failure of a remote cascade connection the block sheds to Man until a remote cascade connection is
restored.
Shed With No Return Options

Note
During Shed with No Return Options, the target mode is changed, while the actual mode stays the same.
115
Instruction Manual
August 2012
D103412X012
For any shed with no return option, the target mode changes as determined by the option. Therefore, there is no
attempt to restore the connection following failure. The behavior on change to the remote cascade target mode is
identical to that for Shed With Return Options.
NormalOn failure of a remote cascade connection the block sets the target mode to the highest permitted
nonremote mode. Cas is the highest permitted nonremote mode and Auto is is the next highest permitted
nonremote mode. If Cas or Auto are not available, the block will shed by default to Man.
Retained TargetThe retained target mode is the previous target mode before it was changed to RCAS or ROUT. On
failure of a remote cascade connection the block sets the target mode to the retained target mode.
AutoOn failure of a remote cascade connection, the block sets the target mode to Auto, if permitted.
ManOn failure of remote cascade connection, the block sets the target mode to Man, if permitted.
The user may configure SHED_OPT [27] so that it calls for a target mode that is not permitted. When doing this, the
mode logic uses the following rules as applied by the remote logic:
Shed logic never results in a nonpermitted target mode.
Shed logic never attempts to attain an actual mode of Auto or Cas if that mode is not permitted.
Status Handling
Output or readback fault detection is reflected in the status of PV [7], OUT [9], and BKCAL_OUT [25]. A limited SP [8]
condition is reflected in the BKCAL_OUT [25] status. When simulation is enabled through the SIMULATE [10] attribute,
you can set the value and status for PV [7] and READBACK [16].
When the block is in Cas mode and the CAS_IN [17] input goes bad, the block sheds mode to the next permitted
mode.
Setting the Output

To set the output for the AO block, you must first set the mode to define the manner in which the block determines its
setpoint. In Manual mode the value of the output attribute (OUT [9]) must be set manually by the user, and is
independent of the setpoint. In Automatic mode, OUT [9] is set automatically based on the value specified by the set
point (SP [8]) in engineering units and the I/O Options attribute. In addition, you can limit the SP [8] value and the rate
at which a change in the SP [8] is passed to OUT [9].
In Cascade mode, the cascade input connection (CAS_IN [17]) is used to update the SP [8]. The back calculation
output (BKCAL_OUT [25]) is wired to the back calculation input (BKCAL_IN [27]) of the upstream block that provides
CAS_IN [17]. This provides bumpless transfer on mode changes and windup protection in the upstream block.
Note
You must wire BKCAL_OUT [25] to BKCAL_IN [27] of the upstream block that provides CAS_IN [17]. Otherwise, the AO will not
initialize properly, and the setpoint at CAS_IN [17] will not be passed to OUT [9].
An analog readback value, such as valve position, is shown by the process value (PV [7]) attribute in engineering units.
To support testing, you can enable simulation, which allows you to manually set the channel feedback. There is no
alarm detection in the AO function block.
116
Instruction Manual
D103412X012

August 2012
To select the manner of processing the SP and the channel output value configure the setpoint limiting options, the
tracking options, and the conversion and status calculations.
Output Block PV Status

The Output Block PV Status is determined by the value of the PlantWeb Alerts Set PV Status parameter in the
transducer block (PWA_SET_STATUS [97]), the Transducer Block mode, and enabled Active PlantWeb alarms. Refer to
table 411.
Set Point Selection and Limiting

To select the source of the SP [8] value use the MODE [5] attribute. In Automatic (Auto) mode, the local,
manuallyentered SP [8] is used. In Cascade (Cas) mode, the SP [8] comes from another block through the CAS_IN [17]
input connector. In RemoteCascade (RCas) mode, the SP [8] comes from a host computer that writes to RCAS_IN [28].
The range and units of the SP [8] are defined by the PV_SCALE [11] attribute.
In Manual (Man) mode the SP [8] automatically tracks the PV [7] value when you select the SPPV Track in Man I/O
option in IO_OPTS [14]. This option can be used to minimize valve movement when the AO block is transitioned from
Manual mode to Auto. You can disable this option in OOS mode only.
The SP [8] value is limited to the range defined by the setpoint high limit attribute (SP_HI_LIM [20]) and the setpoint
low limit attribute (SP_LO_LIM [21]).
In Auto mode, the rate at which a change in the SP [8] is passed to OUT [9] is limited by the values of the setpoint
upward rate limit attribute (SP_RATE_UP [19]) and the setpoint downward rate limit attribute (SP_RATE_DN [18]). A
limit of zero disables rate limiting.
As shown in figure 48, the block executes a percentage of the set point change each macrocycle. For example, if the
set point rate is set at 10% per second and the macrocycle is 500 milliseconds (0.5 seconds or 50% of 1 second), then
during the first macrocycle the set point will change 5% (50% of the 10% per second rate). If the macrocycle is 750
milliseconds (0.75 seconds or 75% of 1 second), then during the first macrocycle the setpoint will change 7.5% (75% of
10).
When the transducer block receives the setpoint change from an AO block with rate limits, it will smoothly move the
valve to the requested setpoint at the rate limit configured in the AO block.
In Auto mode, the converted SP [8] value is stored in the OUT [9] attribute. In Man mode, the OUT [9] attribute is set
manually, and is used to set the analog output defined by the CHANNEL [22] parameter.
You can access the actuator position associated with the output channel through the READBACK [16] parameter (in
OUT units) and in the PV [7] attribute (in engineering units). The digital valve controller supports position feedback
and therefore provides the actual valve position in PV [7] and READBACK [16] directly.
117
Instruction Manual

August 2012
D103412X012
Figure 48. Analog Output Function Block Timing Diagram
CAS_IN, 2
1 macrocycle
SPRATEDN
1 macrocycle
SPRATEUP
OUT
TRANSDUCER BLOCK
TRAVEL TARGET
SP
B27181
1 second
1 second
1 second
1 second
Time
Action On Fault Detection

To define the action you wish the valve to take when the block is in CAS mode, and the CAS_IN [17] input detects a
communication failure, or is commanded to go to fault state by the upstream block or the resource block, configure
the following parameters:
IO_OPTS [14]: Determines the action OUT [9] will take upon a fault state. If the IO_OPTS [14] Fault State to Value is
not selected, then OUT [9] holds its last position when Fault State is set. If Fault State to Value is selected, OUT [9]
goes to the FSTATE_VAL [24] value when Fault State is set.
FSTATE_TIME [23]: The length of time, in seconds, that the AO block will wait to set Fault State. When Fault State is
set, the OUT [9] value goes to either the FSTATE_VAL [24] value or holds its last position, depending on I/O_OPTS [14].
When the block has a target mode of CAS, a fault condition will be detected if the CAS_IN [17] has a BAD status or an
Initiate Fault State substatus is received from the upstream block.
FSTATE_VAL [24]: Determines the OUT [9] value if IO_OPTS Fault State to Value is selected. The OUT [9] value
transitions to FSTATE_VAL [24] after FSTATE_TIME [23] elapses and the fault condition has not cleared.
I/O Options
The I/O options parameter (IO_OPTS [14]) allows you to select how the I/O signals are processed. You can set I/O
options in Out of Service mode only. The following I/O options are available in the AO block:
Use PV for BKCAL_OUTChanges the BKCAL_OUT [25] value to the PV [7] value. When the Use PV for BKCAL_OUT
option is not enabled (False), the BKCAL_OUT [25] value is the working setpoint value.
Target to Man if Fault State ActivatedSet the target mode to Man, thus losing the original target, if Fault State is
activated. This latches an output block into the manual mode.
118
Instruction Manual
D103412X012
August 2012
Use Fault State value on RestartUse the value of FSTATE_VAL [24] for SP [8] when power is restored or if the device is
restarted, otherwise use the last value saved in nonvolatile memory. This does not act like Fault State, it only uses the
value of FSTATE_VAL [24].
Fault State to ValueThe output action to take when a fault occurs (if not selected, use hold last value; if selected, use
FSTATE_VAL [24]).
Increase to CloseIf the Increase to Close bit is set the value to the transducer is inverted, e.g. 20% becomes 80%.
SP-PV Track in ManPermits the setpoint to track the process variable when the target mode of the block is MAN.
SP-PV Track in LO or IManPermits the setpoint to track the process variable when the actual mode of the block is LO
or IMan.
SP Track retained TargetPermits the setpoint to track the RCas or Cas parameter based on the retained target mode
when the actual mode of the block is LO or Man. When SPPV track options are enabled, the SP Track retained target
will have precedence in the selection of the value to track when the actual mode is Man and LO.
Simulation
When simulate is active, the transducer subparameters show the actual transducer block status and value as normally
passed back to the AO block. The Simulate subparameters are writable and replace actual transducer values.
Note
When simulate is active, the output block no longer writes values to the transducer block. If the Output Blk Timeout period is
exceeded, the transducer block may move the valve to the Zero Power Condition depending on the configuration of the Output
Block Timeout Alert.
Application Information
The configuration of an AO function block and its associated output channels depends on the specific application. A
typical configuration for the Analog Output involves the following attributes:
PV_SCALE
Set the range and engineering units to values that correspond to the operation range.
For the digital valve controller, PV_SCALE [11] is typically set between 0 and 100%.
BKCAL_OUT
If you are using the CAS_IN [17] connector wired from another block, wire the
BKCAL_OUT [25] attribute to the other block's BKCAL_IN [27] attribute.
IO_OPTS
Set the type of tracking and action upon fault state.
SHED_OPT
Set the action to be taken when the set point or output are not updated in a remote
mode.
Block Errors
Table 424 lists conditions reported in the BLOCK_ERR [6] parameter. Conditions in italics are not applicable for the AO
block and are provided only for your reference.
119
Instruction Manual

August 2012
D103412X012
Table 424. BLOCK_ERR Conditions

Condition Number
Other (N/A)
Block Configuration Error CHANNEL and SHED_OPT set to 0
Simulate active Simulation is enabled and the block is using a simulated value in its execution.
Local Override Device in fault state. Actual mode LO.
Device Fault State Set AO block in fault state after FSTATE_TIME because of Bad status or IFS substatus on CAS_IN or
Resource block commanded fault state.
Device Needs Maintenance Soon Indicates a Maintenance PlantWeb Alert condition is active if Block Error Reporting is
enabled. See page 86.
Output failure PV has bad status.
Memory Failure (N/A)
10
Lost Static Data (N/A)
11
Lost NV Data (N/A)
12
13
Device Needs Maintenance Now Indicates Failed PlantWeb Alert condition is active if Block Error Reporting is enabled. See
page 86.
14
Power Up This condition exists after power up until actual mode is not Out of Service.
15
Out of Service The block is in Out of Service (OOS) mode.
AO Function Block Parameter List (table 425)

Table 425. Analog Output Function Block Parameter Definitions
Label
PARAMETER_NAME
Index
Number
RO /
RW
Block
Mode
Range
Initial
Value
Description
Static Revision
ST_REV
RO
N/A
0 to 65535

The revision level of the static data associated with
the function block. The revision value will be
incremented each time a static parameter value in
the block is changed.
Tag Description
TAG_DESC
RW
ALL
7 bit ASCII
Spaces

The user description of the intended application of
the block.
Strategy
STRATEGY
RW
ALL
0 to 65535

The strategy field can be used to identify grouping
of blocks. This data is not checked or processed by
the block.
Alert Key
ALERT_KEY
RW
ALL
1 to 255

The identification number of the plant unit. This
information may be used in the host for sorting
alarms, etc.
-Continued-
120
Instruction Manual
D103412X012
August 2012
Table 425. Analog Output Function Block Parameter Definitions (Continued)

Label
PARAMETER_NAME
Block Mode
MODE_BLK
TARGET
ACTUAL
Index
Number
RO /
RW
Block
Mode
OOS
MAN
AUTO
AUTOCAS
AUTORCAS
OOS until
block is
configured,
then last valid
target
OOS+MAN+AUTO+
CAS+RCAS
5.1
RW
ALL
5.2
RO
ALL
OOS
OOS+MAN+A
UTO+
CAS+RCAS
5.3
RW
ALL
NORMAL
5.4
RW
ALL
Process Variable
PV
Initial
Value
Description
PERMITTED
Block Error
BLOCK_ERR
Range
RO
RO
Data Type: DS69

Valid Bits: 7: OOS, 6: IMAN, 5: LO, 4: MAN, 3: AUTO,
2: CAS, 1: RCAS
The actual, target, permitted, and normal modes of
the block.
(Note: Bit 6 (IMAN) is valid for ACTUAL only)
AUTO
N/A
Error
3: Simulate Active
4: Local Override
5: Device Fault State Set
8: Output Failure
14: Powerup
15: OutofService
N/A
PV Status set equal to

READBACK status
Dynamic

0=inactive
1=active
This parameter reflects the error status associated
with the hardware or software components
associated with a block. It is a bit string, so that
multiple errors may be shown. See table 424.
Dynamic
Data Type: DS65

The process variable used in block execution. This
value is converted from READBACK to show the
actuator position in the same units as the setpoint
value.
Set Point
SP
OOS
MAN
AUTO
PV_SCALE +/- 10%
Dynamic
Data Type: DS65

The SP of the analog block. Can be derived from
CAS_IN, RCAS_IN in normal modes, or can track PV
in MAN, IMan or LO modes. IO_OPTS is used to
determine value of SP in MAN, IMan or LO. If no
IO_OPTS for SP tracking are set, SP will freeze when
mode changes from CAS or RCAS.
Output
OUT
MAN
OOS
OUT_SCALE +/- 10%
Dynamic
Data Type: DS65

The primary value and status calculated by the
block in Auto mode. OUT may be set manually in
Man mode.
Simulate
SIMULATE
10
SIMULATE_STATUS
10.1
RW
ALL
SIMULATE_VALUE
10.2
RW
ALL
TRANSDUCER_STATUS
10.3
RO
ALL
TRANSDUCER_VALUE
10.4
RO
ALL
ENABLE/DISABLE
Process Value Scale

PV_SCALE
Transducer Scale
XD_SCALE
10.5
11
12
RW
RW
RO
Data Type: DS82

Allows the analog input to be manually supplied
when simulate is enabled. When simulation is
disabled, the simulate value and status track actual
value & status.
ALL
0: Not Initialized
1: Simulation Disable
2: Simulation Active
OOS
EU at 100%
EU at 0%
Units index
Decimal Point
100
0
%
2
Data Type: DS68

The high and low scale values, engineering units
code, and number of decimal places to be used in
displaying the PV parameter and parameters which
have the same scaling as PV.
OOS
EU at 100%
EU at 0%
Units index
Decimal Point
100 only
0 only
% only
2
Data Type: DS68

The high and low scale values and engineering
units code are read only. This parameter
determines the number of digits to the right of the
decimal point used with the value obtained from
the transducer for a specified channel.
1: Simulation
Disabled
-Continued-
121
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Grant Deny
GRANT_DENY
Index
Number
RO /
RW
Block
Mode
13.1
RW
ALL
DENY
13.2
RW
ALL
Status Options
STATUS_OPTS
Initial
Value
13
GRANT
I/O Options
IO_OPTS
Range
14
OOS
15
OOS
0: Program
1: Tune
2: Alarm
3: Local
1: SP tracks PV in Man
3: SP tracks PV in LO or
Iman
4: SP Track retained
target in Man or LO
5: Increase to Close
6: Fault State to value
0=freeze
1=go to Fault State
value
7: Use Fault State
value on restart
8: Target to Man if
Fault State activated
9: Use PV for
BKCAL_OUT
0=SP
1=PV
4: Propagate Failure
Backward
All bits: 0
All bits: 0
Cascade Input
CAS_IN
16
17
RO
All bits: 0
All bits: 0

0=disable
1=enable
Options the user may select for the block
processing of status.
N/A
ALL
Data Type: DS70

Options for controlling access of host computers
and local control panels to operating, tuning, and
alarm parameters of the block.
GRANT: 1 = granted, 0= N/A
DENY: 1 = denied, 0 = N/A

0=disable
1=enable
Allows you to select the type of tracking and the
output value when a fault condition occurs.
Status
Readback
READBACK
Description
Value
Dynamic
Status
BAD:
NC:
const
Value
Data Type: DS65

Readback is the decharacterized valve position as
reported by the transducer block parameter
FINAL_POSITION_VALUE [17]. This correlates with
the AO block parameter OUT [9], which is the
setpoint to the transducer. READBACK is the
simulated input if SIMULATE is enabled or the
transducer block feedback if SIMULATE is disabled.
Data Type: DS65
The setpoint value from another function block.
Setpoint Rate Down

SP_RATE_DN
18
ALL
Positive, 0 disables
rate limiting PV units
+INF
Data Type: Float

Ramp rate for downward set point changes. When
the ramp rate is set to zero, the set point is used
immediately.
Setpoint Rate Up
SP_RATE_UP
19
ALL
Positive, 0 disables
rate limiting PV units
+INF
Data Type: Float

Ramp rate for upward set point changes. When the
ramp rate is set to zero, the setpoint is used
immediately.
Setpoint High Limit

SP_HI_LIM
20
ALL
PV Scale +/- 10%
100
Data Type: Float

The highest set point value allowed. SP_HI_LIM
must be greater than SP_LO_LIM.
Setpoint Low Limit

SP_LO_LIM
21
ALL
PV Scale +/- 10%
Data Type: Float

The lowest set point value allowed. SP_LO_LIM
must be less than SP_HI_LIM.
AO Channel
CHANNEL
22
OOS
1=Setpoint
Fault State Time

FSTATE_TIME
23
ALL
Positive, seconds
-Continued-
122
1=Setpoint

Defines which transducer parameter receives the
AO output. Select Setpoint to control valve
position.
Data Type: Float
Time from failure detection to reaction if failure still
exists.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Index
Number
Fault State Value

FSTATE_VAL
24
Back Calculation Output

BKCAL_OUT
25
Remote Cascade Input

RCAS_IN
26
RO /
RW
Block
Mode
ALL
Range
PV Scale +/- 10%
Initial
Value
Description
Data Type: Float

Preset value to use if I/O_OPTS Fault State to Value
or Use Fault State Value on Restart is set.
Dynamic
Data Type: DS65

The value and
status required by the BKCAL_IN input of another
block to prevent reset windup and to provide
bumpless transfer to closed loop control.
Status Limits
RO
N/A
Value
Shed Options
SHED_OPT
27
Remote Cascade Output

RCAS_OUT
28
Update Event
UPDATE_EVT
29
ALL
ALL
RO
N/A
Status
BAD: NoCom:
NoVal:
const
Value
0 Trk
Defined by FF spec
0=Invalid
1=Normal Shed,
Normal Return
2=Normal Shed, No
Return
3=Shed to Auto,
normal return
4=Shed to Auto, no
return. Target mode
changes to Auto on
detection of a shed
condition
5=Shed to Manual,
normal return
6=Shed to Manual, No
return. Target mode
changes to MAN on
detection of a shed
condition.
7=Shed to retained
target, normal return
8=Shed to retained
target, no return.
(Change target to
retained target)
Status
Value
Dynamic
UNACKNOWLEDGED
29.1
RW
N/A
0:Undefined
1:Acknowledged
2:Unacknowledged
0: Undefined
UPDATE_STATUS
29.2
RO
N/A
0:Undefined
1:Update reported
2:Update not reported
0: Undefined
TIME_STAMP
29.3
RO
N/A
STATIC_REVISION
29.4
RO
N/A
RELATIVE_INDEX
29.5
RO
N/A
RW
N/A
0:Undefined
1:Acknowledged
2:Unacknowledged
0:Undefined
1:Clear reported
2:Clear not reported
3:Active reported
4:Active not reported
Block Alarm
BLOCK_ALM
UNACKNOWLEDGED
Data Type: DS65

Target SP and status by supervisory host

Defines the action to be taken when the set point is
not updated in a remote mode.
Data Type: DS65

Block set point and status after ramping
Data Type: DS73

This alert is generated by any changes to static data.
30
30.1
0: Undefined
ALARM_STATE
30.2
RO
N/A
0: Undefined
TIME_STAMP
30.3
RO
N/A
SUBCODE
30.4
RO
N/A
VALUE
30.5
RO
N/A
Data Type: DS72

The block alarm is used for all configuration,
hardware, connection failure, or system problems
in the block.
0
-Continued-
123
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Index
Number
RO /
RW
Block
Mode
Initial
Value
Range
Description
Extended Parameters
StdDev
STDDEV
31
RO
N/A
positive float
Dynamic
Data Type: Float

Standard Deviation. To support DeltaV Variability
measurement.
Cap StdDev
CAP_STDDEV
32
RO
N/A
positive float
Dynamic
Data Type: Float

Capability Standard Deviation. To support DeltaV
Variability measurement.
View Lists
Table 426. AO Function Block, View 1
Index Number
1
Parameter
ST_REV
Index Number
1
Parameter
ST_REV
5.1
5.1
5.2
5.2
5.3
5.3
5.4
5.4
BLOCK_ERR
BLOCK_ERR
PV
PV
SP
SP
OUT
OUT
16
READBACK
16
READBACK
17
CAS_IN
17
CAS_IN
25
BKCAL_OUT
26
RCAS_IN
28
RCAS_OUT
31
STDDEV
32
CAP_STDDEV

Index Number
124
Parameter
ST_REV
11
PV_SCALE
12
XD_SCALE
13.1
GRANT_DENY.GRANT
13.2
GRANT_DENY.DENY
20
SP_HI_LIM
21
SP_LO_LIM

Index Number
Parameter
ST_REV
STRATEGY
ALERT_KEY
14
IO_OPTS
15
STATUS_OPTS
18
SP_RATE_DN
19
SP_RATE_UP
22
CHANNEL
23
FSTATE_TIME
24
FSTATE_VAL
27
SHED_OPT
Instruction Manual
D103412X012
August 2012
Field Communicator Menu Structure

ANALOG OUTPUT FUNCTION BLOCK
Quick Config
Alert Key
Process Value Scale: EU at 100%
Process Value Scale: Units Index
Process Value Scale: Decimal
Simulate: Simulate Status
Simulate: Simulate Value
Simulate: Transducer Status
Simulate: Transducer Value
Simulate: Simulate En/Disable
Setpoint: Status
Setpoint: Value
Setpoint High Limit
Setpoint Low Limit
Common Config
Alert Key
I/O Options
Block Mode: Target
Block Mode: Actual
Block Mode: Permitted
Block Mode: Normal
Setpoint: Status
Setpoint: Value
Setpoint High Limit
Setpoint Low Limit
Advanced Config
Fault State Time
Fault State Value
Shed Options
Setpoint Rate Down
Setpoint Rate Up
Static Revision
Status Options
Strategy
Transducer Scale: EU at 100%
Transducer Scale: Units Index
Transducer Scale: Decimal
I/O Reference
AO Channel
Connectors
Back Calculation Output: Status
Back Calculation Output: Value
Cascade Input: Status
Cascade Input: Value
Output: Status
Output: Value
Online
Block Error
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Output: Status
Output: Value
Process Value: Status
Process Value: Value
Remote Cascade Input: Status
Remote Cascade Input: Value
Remote Cascade Output: Status
Remote Cascade Output: Value
Readback: Status
Readback: Value
Setpoint: Status
Setpoint: Value
Status
Block Error
Other
Tag Description
Grant Deny: Grant
Grant Deny: Deny
Update Event: Unacknowledged
Update Event: Update State
Update Event: Time Stamp
Update Event: Static Rev
Update Event: Relative Index
Block Alarm: Unacknowledged
Block Alarm: Alarm State
Block Alarm: Time Stamp
Block Alarm: Subcode
Block Alarm: Value
StdDev
Cap StdDev
All
Characteristics
Static Revision
Tag Description
Strategy
Alert Key
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Block Error
Setpoint: Status
Setpoint: Value
Output: Status
Output: Value
Grant Deny: Grant
Grant Deny: Deny
I/O Options
Status Options
Readback: Status
Readback: Value
Setpoint Rate Down
Setpoint Rate Up
Setpoint High Limit
Setpoint Low Limit
AO Channel
Fault State Time
Fault State Value
Shed Options
Block Alarm: Value
StdDev
Cap StdDev
125
Instruction Manual
Detailed SetupPID Function Block

August 2012
D103412X012
PID Function Block

Overview
The PID function block (figure 49) combines all of the necessary logic to perform proportional/integral/derivative
(PID) control. The block supports mode control, signal scaling and limiting, feedforward control, override tracking,
alarm limit detection, and signal status propagation.
Figure 49. Proportional+Integral+Derivative (PID) Function Block
BKCAL
IN
CAS
IN
BKCALOUT
VAL
FF
TRK
TRK
IN
OUT
PID
IN
D
VAL
BKCAL_IN = THE ANALOG INPUT VALUE AND STATUS FROM ANOTHER BLOCK'S BKCAL
_OUT OUTPUT THAT IS USED FOR BACKWARD OUTPUT TRACKING FOR BUMPLESS
TRANSFER AND TO PASS LIMIT STATUS.
CAS_IN = THE REMOTE SETPOINT VALUE FROM ANOTHER FUNCTION BLOCK.
FF_VAL = THE FEEDFORWARD CONTROL INPUT VALUE AND STATUS.
IN = THE CONNECTION FOR THE PROCESS VARIABLEFROM ANOTHER FUNCTION BLOCK.
TRK_IN_D = INITIATES THE EXTERNAL TRACKING FUNCTION.
TRK_VAL = THE VALUE AFTER SCALING APPLIED TO OUT IN LOCAL OVERRIDE MODE.
BKCAL_OUT = THE VALUE AND STATUS REQUIRED BY THE BKCAL_IN INPUT OF ANOTHER
FUNCTION BLOCK TO PREVENT RESET WINDUP AND TO PROVIDE BUMPLESS TRANSFER
TO CLOSED LOOP CONTROL.
OUT = THE BLOCK OUTPUT AND STATUS.
B2720
The block supports two forms of the PID equation: Standard and Series. You can choose the appropriate equation
using the MATHFORM [70] parameter. The Standard ISA PID equation is the default selection.
Standard Out + GAIN
Series Out + GAIN
ex
1 ) t s 1) 1 ) T
r
ex
t ds
)
t ds ) 1
1 ) t1s ) T t s t)s 1) 1 )F
d
where
GAIN:
proportional gain value
r:
integral action time constant (RESET parameter) in seconds
s:
laplace operator
d:
derivative action time constant (RATE parameter)
126
Instruction Manual
D103412X012
August 2012
fixed smoothing factor of 0.1 applied to RATE
F:
feedforward control contribution from the feedforward input (FF_VAL)
E:
error between setpoint and process variable
To further customize the block for use in your application, you can configure filtering, feedforward inputs, tracking
inputs, setpoint and output limiting, PID equation structures, and block output action. Table 432 lists the PID block
parameters and their descriptions, units of measure, and index numbers, and figure 410 illustrates the internal
components of the PID function block.
Figure 410. PID Function Block Schematic
FFGAIN
FFSCALE
Feedforward
Calculation
FFVAL
BKCALIN
MODE
TRKIND
BKCALOUT
RCASOUT
ROUTOUT
ROUTIN
RCASIN
Setpoint
Limiting
CASIN
Operator
Setpoint
IN
SPHILIM
SPLOLIM
SPRATEDN
SPRATEUP
Scaling
and
Filtering
PVSCALE
PVFILTER
TRKVAL
PID
Equation
GAIN
RATE
RESET
Alarm
Detection
Output
Limiting
OUT
OUTHILIM
OUTLOLIM
OUTSCALE
Operator
Output
HIHILIM
HILIM
DVHILIM
DVLOLIM
LOLIM
LOLOLIM
Convert
TRKSCALE
OUTSCALE
B2721
127
Instruction Manual
August 2012
D103412X012
Modes
The PID function block supports the following modes:
Manual (Man)The block output (OUT [9]) may be set manually.
Automatic (Auto)The SP [8] may be set manually and the block algorithm calculates OUT [9].
Cascade (Cas)The SP [8] is calculated in another block and is provided to the PID block through the CAS_IN [18]
connection.
RemoteCascade (RCas)The SP [8] is provided by a host computer that writes to the RCAS_IN [32] parameter.
RemoteOutput (ROut)The OUT [9] is provided by a host computer that writes to the ROUT_IN [33] parameter.
Local Override (LO)The track function is active. OUT [9] is set by TRK_VAL [39]. The BLOCK_ERR [6] parameter
shows Local override.
Initialization Manual (IMan)The output path is not complete (for example, the cascade-to-slave path might not be
open). In IMan mode, OUT [9] tracks BKCAL_IN [27].
Out of Service (OOS)The block is not processed. The OUT [9] status is set to Bad: Out of Service. The BLOCK_ERR
[6] parameter shows Out of service.
You can configure the Man, Auto, Cas, and OOS modes as permitted modes for operator entry.
Mode Handling
Shed from or climb to a remote mode is determined by the parameter SHED_OPT [34]. A block climbs and sheds
through the same path. For example, if SHED_OPT [34] specifies that a block should shed to Auto, then, if the block
target mode is set to RCas, the block goes through Auto on the way to RCas. You can configure the shed option as
follows:

Remote cascade or remote output connection failure shifts actual mode but keeps trying to restore remote cascade or
remote output (in other words, the remote cascade or remote output target mode stays in effect).
NormalOn failure of a remote connection, the block attempts to attain the highest permitted nonremote mode
until the remote connection is restored. Cas is the highest permitted nonremote mode and Auto is is the next highest
Retained TargetThe retained target mode is the mode the block was in before changing to one of the remote target
modes. On failure of a remote connection, the block attempts to attain the retained target mode.
AutoOn failure of a remote connection, the block attempts to attain Auto, if permitted, until the remote connection
is restored.
ManOn failure of a remote connection, the block sheds to Man until a remote connection is restored.
128
Instruction Manual
D103412X012
August 2012

attempt to restore the connection following failure. The behavior on change to a remote target mode is identical to
that for Shed With Return Options.
NormalOn failure of a remote connection, the block sets the target mode to the highest permitted nonremote
mode. Cas is the highest permitted nonremote mode and Auto is is the next permitted nonremote mode. If Cas or
Auto are not available, the block will shed by default to Man.
Retained TargetThe retained target mode is the mode the block was in before changing to one of the remote target
modes. On failure of a remote connection, the block sets the target mode to the retained target mode.
AutoOn failure of a remote connection, the block sets the target mode to Auto, if permitted.
ManOn failure of a remote connection, the block sets the target mode to Man, if permitted.
The user may configure SHED_OPTS [34] so that it calls for a target mode that is not permitted. When doing this, the
Status Handling
If the input status on the PID block is Bad, the mode of the block reverts to Manual. In addition, you can select the
Target to Manual if Bad IN status option to direct the target mode to revert to manual. You can set the status option in
Manual or Out of Service mode only.
Set Point Selection and Limiting

The set point of the PID block is only valid when the block is in Auto, Cas, or RCas. Figure 411 illustrates the method
for set point selection. You can configure the SP_HI_LIM [21] and SP_LO_LIM [22] parameters to limit the set point. In
Cascade or Remote Cascade mode, the set point is adjusted by another function block or by a host computer, and the
output is computed based on the set point.
Figure 411. PID Function Block Set Point Selection
Operator
Set point
Auto
Man
CAS
SPHILIM
SPLOLIM
SPRATEUP
SPRATEDN
Setpoint
Limiting
Rate
Limiting
Auto
Man
CAS
B2722
In Automatic mode, the set point is entered manually by the operator, and the output is computed based on the set
point. In Auto mode, you can also adjust the set point limit and the set point rate of change using the SP_RATE_UP
[20] and SP_RATE_DN [19] parameters.
129
Instruction Manual
August 2012
D103412X012
In Manual mode the output is entered manually by the operator. In Remote Output mode, the output is entered by a
host computer.
Output Selection and Limiting

Output selection is determined by the mode and the set point. In Automatic, Cascade, or Remote Cascade mode, the
output is computed by the PID control equation. In Manual and Remote Output mode, the output may be entered
manually (see also Set Point Selection and Limiting). You can limit the output by configuring the OUT_HI_LIM [28] and
OUT_LO_LIM [29] parameters.
Filtering
The filtering feature changes the response time of the device to smooth variations in output readings caused by rapid
changes in input. You can adjust the filter time constant (in seconds) using the PV_FTIME [16] or SP_FTIME [69]
parameters. Set the filter time constant to zero to disable the filter feature.
Feedforward Calculation
The feedforward value (FF_VAL [40]) is scaled (FF_SCALE [41]) to a common range for compatibility with the output
scale (OUT_SCALE [11]). A gain value (FF_GAIN [42]) is applied to achieve the total feedforward contribution.
Output Tracking
Output tracking is enabled through the control options. You can set control options in Manual or Out of Service mode
only.
The Track Enable control option must be set to True for the track function to operate. When the Track in Manual
control option is set to True, the operator cannot override the tracking function in Manual mode. When Track in
Manual is False, the operator can override the tracking function when the block is in Manual mode. Activating the track
function causes the block's actual mode to revert to Local Override.
The TRK_VAL [38] parameter specifies the value to be converted and tracked into the output when the track function
is operating. The TRK_SCALE [37] parameter specifies the range of TRK_VAL [38].
When the TRK_IN_D [38] parameter is True and the Track Enable control option is True, the TRK_VAL [38] input is
converted to the appropriate value and output in units of OUT_SCALE [11].
Set Point Tracking

You can configure the method for tracking the set point by configuring the following control options (CONTROL_OPTS
[12]):
SP-PV Track in ManPermits the SP [8] to track the PV [7] when the actual mode of the block is Man.
SP-PV Track in LO or IManPermits the SP [8] to track the PV [7] when the actual mode of the block is Local Override
(LO) or Initialization Manual (IMan).
SP-PV Track in ROUTPermits the SP [8] to track the PV [7] when the actual mode of the block is RemoteOut
(ROUT).
SP Track retained TargetCauses the set point to track the RCAS or CAS parameter based on the retained target
mode when the actual mode is MAN or LO.
130
Instruction Manual
D103412X012
August 2012
Act On IRIf this option is true, then when IR (Initialization Requested) is received on BKCAL_IN [27], the SP [8] will
be adjusted within setpoint limits to provide bumpless transfer when the cascade is closed. If the setpoint required
to provide bumpless transfer is outside the setpoint limits, then any difference added to provide bumpless transfer
will be removed in the BAL_TIME [25].
When one of these options is set, the SP[8] value is set to the PV [7] value while in the specified mode.
You can select the value that a master controller uses for tracking by configuring the Use PV for BKCAL_OUT control
option. The BKCAL_OUT [31] value tracks the PV value. BKCAL_IN [27] on a master controller connected to
BKCAL_OUT [31] on the PID block in an open cascade strategy forces its OUT [9] to match BKCAL_IN [27], thus
tracking the PV from the slave PID block into its cascade input connection (CAS_IN [18]). If the Use PV for BKCAL_OUT
option is not selected, the working set point (SP_WRK [68]) is used for BKCAL_OUT [31].
You can set control options in Manual or Out of Service mode only. When the mode is set to Auto, the SP [8] will
remain at the last value (it will no longer follow the PV [7].
PID Equation Structures for Enhanced PID Block

Note
Extended parameters are not available at this time for all host systems. Refer to your host system documentation, or contact your
Emerson Process Management sales office for additional information.
Configure the STRUCTURECONFIG [71] parameter to select the PID equation structure. You can select one of the
following choices:
Proportional, integral, and derivative on error (PID)
Proportional and integral on error, derivative on PV (PI_D)
Integral on error, proportional and derivative on PV (I_PD)
Proportional on error, derivative on error (PD)
Integral on error, derivative on error (ID)
Integral on error, derivative on PV (I_D)
Two degrees of Freedom (2DOF)
Reverse and Direct Action

To configure the block output action, set the Direct Acting control option. This option defines the relationship
between a change in PV [7] and the corresponding change in output. With Direct Acting enabled (True), an increase in
PV results in an increase in the output.
You can set control options in Manual or Out of Service mode only.
Alarm Detection
A block alarm will be generated whenever the BLOCK_ERR [6] has an error bit set. The types of block error for the PID
block are defined above.
131
Instruction Manual

August 2012
D103412X012
Process alarm detection is based on the PV [7] value. You can configure the alarm limits of the following standard
alarms:
High (HI_LIM [51])
High high (HI_HI_LIM [49])
Low (LO_LIM [53])
Low low (LO_LO_LIM [55])
Additional process alarm detection is based on the difference between SP [8] and PV [7] values and can be configured
via the following parameters:
Deviation high (DV_HI_LIM [57])
Deviation low (DV_LO_LIM [59])
In order to avoid alarm chattering when the variable is oscillating around the alarm limit, an alarm hysteresis in percent
of the PV span can be set using the ALARM_HYS [47] parameter. The priority of each alarm is set in the following
parameters:
HI_PRI [50]
HI_HI_PRI [48]
LO_PRI [52]
LO_LO_PRI [54]
DV_HI_PRI [56]
DV_LO_PRI [58]
Alarms are grouped into five levels of priority, as shown in table 430.
Table 430. PID Function Block Alarm Priorities
Priority Description(1)
Priority Number
0
The alarm is disabled
An alarm condition with a priority of 1 can be recognized by the system. The device monitors the alarm but does not report it
until requested by the host system.
An alarm condition with a priority of 2 is reported to the operator, but generally does not require operator attention (such as
diagnostics and system alerts).
3-7
Alarm conditions of priority 3 to 7 are advisory alarms of increasing priority.
8-15
Alarm conditions of priority 8 to 15 are critical alarms of increasing priority.
1. The priority classes advise and critical have no relationship to Plant Web Alerts.
The PID function block is a powerful, flexible control algorithm that is designed to work in a variety of control
strategies. The PID block is configured differently for different applications.
DeltaV Tune
DeltaV Tune quickly and automatically determines optimal tuning parameters for PID control loops. For more
information on DeltaV Tune, refer to DeltaV Books Online or DeltaV documentation.
Block Errors
Table 431 lists conditions reported in the BLOCK_ERR [6] parameter. Conditions in italics are not applicable for the PID
132
Instruction Manual
D103412X012
August 2012

Condition Number
Other (N/A)
Block Configuration ErrorSHED_OPT or BYPASS set to 0
Simulate Active (N/A)
Local OverrideThe actual mode is LO and Track Enable is set.
Device Fault State Set (N/A)
Device Needs Maintenance Soon (N/A)
Input failure/process variable has Bad statusThe parameter linked to IN is indicating a Bad status.
Output Failure (N/A)
10
11
Lost NV Data (N/A)
12
13
Device Needs Maintenance Now (N/A)
14
Power UpSet if devices was powered up with this block in Out of Service (OOS) mode. Cleared on first change of mode to other
than OOS.
15
Out of ServiceThe actual mode is Out of Service (OOS).
PID Function Block Parameter List (table 432)

Table 432. PID Function Block System Parameters Definitions
Label
PARAMETER_NAME
Index
Number
RO /
RW
Block
Mode
Range
Initial Value
Description
Static Revision
ST_REV
RO
N/A
0 to 65535

incremented each time a static pa rameter value in
Tag Description
TAG_DESC
RW
ALL
7 bit ASCII
Spaces

the block.
Strategy
STRATEGY
RW
ALL
0 to 65535

the block.

alarms, etc.
Alert Key
ALERT_KEY
Block Mode
MODE_BLK
RW
ALL
TARGET
5.1
RW
ALL
ACTUAL
5.2
RO
ALL
PERMITTED
5.3
RW
ALL
NORMAL
5.4
RW
ALL
0 to 255
OOS, MAN, AUTO

CAS, RCAS, ROUT
OOS until
block is
configured,
then last valid
target
OOS
OOS+MAN+AUTO+
CAS+RCAS+ROUT
OOS MAN,
AUTO CAS,
RCAS ROUT
Data Type: DS69

Valid Bits: 7: OOS, 6: IMAN, 5: LO, 4: MAN, 3:
AUTO, 2: CAS, 1: RCAS, 0: ROUT
The actual, target, permitted, and normal modes
of the block.
AUTO
-Continued-
133
Instruction Manual

August 2012
D103412X012
Table 432. PID Function Block System Parameters Definitions (Continued)

Label
PARAMETER_NAME
Index
Number
RO /
RW
Block
Mode
Range
Initial Value
Description
Dynamic

0 = inactive
1 = active
associated with a block. It is a bit string so that
multiple errors may be shown.
Dynamic
Data Type: DS65

The process variable used in block execution.
PV_SCALE +/- 10%
Dynamic
Data Type: DS65

The target block setpoint value. It is the result of
setpoint limiting and setpoint rate of change
limiting.
Status
OUT_SCALE +/- 10%
Dynamic
Defined Bits
Block Error
BLOCK_ERR
RO
N/A
Process Value
PV
RO
N/A
Setpoint
SP
OOS
MAN
AUTO
Output
OUT
MAN
OOS
Process Value Scale

PV_SCALE
10
Output Scale
OUT_SCALE
11
Grant Deny
GRANT_DENY
12
GRANT
DENY
Control Options
CONTROL_OPTS
Status Options
STATUS_OPTS
Input
IN
Process Value Filter Time

PV_FTIME
12.1
12.2
13
14
15
16
1: Block Configuration Error

4: Local Override
7: Input Failure/ Bad PV status
14: Powerup
15: OutofService
Value
OOS
EU at 100%
EU at 0%
Units index
Decimal Point
100
0
%
2
Data Type: DS68

code, and number of digits to the right of the
decimal point associated with PV.
OOS
EU at 100%
EU at 0%t
Units index
Decimal Point
100
0
%
2
Data Type: DS68

decimal point associated with OUT.
ALL
0: Program
1: Tune
2: Alarm
3: Local
All bits: 0
ALL
0: Program
1: Tune
2: Alarm
3: Local
All bits: 0
OOS
0: Bypass Enable
1: SP tracks PV in MAN
2: SP tracks PV in ROUT
3: SP tracks PV in LO or MAN
4: SP tracks RCAS or CAS in
IMAN, LO, MAN or ROUT
5: Direct Acting
7: Track Enable
8: Track in Manual
9: Use PV for BKCAL_OUT
10: Act on IR
12: Restrict SP to limits in
Cas and RCas
13: No output limits in MAN
All bits: 0

0=disable
1=enable
Allows you to specify control strategy options.
OOS
0: IFS (Initiate Fault State)

if BAD IN
1: IFS if BAD CAS_IN
2: Use Uncertain as Good
5: Target to MAN if BAD IN
All bits: 0

0=disable
1=enable
Allows you to select options for status handling
and processing.
ALL
ALL
Status
BAD:
NC:
const
Value
Positive
-Continued-
134
DS65
The block output value and status.
Data Type: DS70

alarm parameters of the block. Not used by the
device.
GRANT: 0=N/A, 1=granted
DENY: 0 = N/A, 1= denied
Data Type: DS65

The primary input value of the block.
Data Type: Float
The time constant of the first-order PV filter. It is
the time, in seconds, required for a 63 percent
change in the IN value.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Bypass
BYPASS
Cascade Input
CAS_IN
Setpoint Rate Down

SP_RATE_DN
Index
Number
RO /
RW
Block
Mode
MAN
OOS
17
18
ALL
19
ALL
Range
Initial Value
1=Off
2=On
0=undefined
Status
BAD
NC:
const
Value
Positive
Description
Data Type: Enum
Used to override the calculation of the block.
When enabled, the SP is sent directly to the
output.
Data Type: DS65
The setpoint value from another block.
+ INF
Data Type: Float

Ramp rate for downward SP changes. When the
ramp rate is set to zero, the SP is used
immediately. PV per second
Setpoint Rate UP
SP_RATE_UP
20
ALL
Positive
+ INF
Data Type: Float

Ramp rate for upward SP changes. When the ramp
rate is set to zero, the SP is used immediately. PV
per second
Setpoint High Limit

SP_HI_LIM
21
ALL
PV Scale +/- 10%, must be

greater than SP_LO_LIM
100
Data Type: Float

The highest SP value allowed.
Setpoint Low Limit

SP_LO_LIM
22
ALL
PV Scale
+/- 10%, must be less than
SP_HI_LIM
Data Type: Float

The lowest SP value allowed.
Gain
GAIN
23
ALL
greater than 0
Data Type: Float

The proportional gain value.
Reset
RESET
24
ALL
Positive
+ INF
Data Type: Float

The integral action time constant. Seconds per
repeat
Balance Time
BAL_TIME
25
ALL
Positive
Data Type: Float

The specified time, in seconds, for the internal
working value of bias to return to the operator set
bias. Also used to specify the time constant at
which the integral term will move to obtain
balance when the output is limited and the mode is
AUTO, CAS, or RCAS.
Rate
RATE
26
ALL
Positive
Data Type: Float

The derivative action time constant, in seconds.
Status
BAD:
NC:
const
Data Type: DS65

The analog input value and status from another
block's BKCAL_OUT output that is used for
backward output tracking for bumpless transfer
and to pass limit status.
Value
Back Calculation Input

BKCAL_IN
27
ALL
Output High Limit

OUT_HI_LIM
28
ALL
OUT_SCALE +/- 10%
100
Data Type: Float

Limits the maximum output value for modes other
than manual.
Output Low Limit

OUT_LO_LIM
29
ALL
OUT_SCALE +/- 10%
Data Type: Float

Limits the minimum output value for modes other
than manual.
Back Calculation Hysteresis

BKCAL_HYS
30
ALL
0 to 50%

BKCAL_OUT
Remote Cascade Input

RCAS_IN
31
32
RO
0.50%
N/A
ALL
Dynamic
BAD:
NoCom:
NoVal:
const
Status
Value
Data Type: Float

The amount the output value must change away
from the its output limit before limit status is
turned off.
Data Type: DS65
The value and status required by the BKCAL_IN
input of another block to prevent reset windup and
to provide bumpless transfer of closed loop
control.
Data Type: DS65
Target setpoint and status that is provided by a
supervisory host. Used when mode is RCAS.
0 Trk
-Continued-
135
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Remote Out Input
ROUT_IN
Shed Options
SHED_OPT
Remote Cascade Output

RCAS_OUT
Remote Out Output

ROUT_OUT
Tracking Scale
TRK_SCALE
Tracking Input Discrete

TRK_IN_D
Tracking Value
TRK_VAL
Feed Forward Value

FF_VAL
Index
Number
RO /
RW
33
ALL
34
35
36
37
38
39
40
Block
Mode
RO
Status
BAD:
NoCom:
NoVal:
const
Value
0 Trk
0=Invalid
1=Normal Shed, Normal
Return
2=Normal Shed, No Return
3=Shed to Auto, normal
return
4=Shed to Auto, no return.
Target mode changes to
Auto on detection of a shed
condition
5=Shed to Manual, normal
return
return. Target mode
changes to MAN on
detection of a shed
condition.
7=Shed to retained target,
normal return
8=Shed to retained target,
no return. (Change target to
retained target)
Description
Data Type: DS65

Target output and status that is provided by a
supervisory host. Used when mode is ROUT.
0=Invalid
Dynamic
Data Type: DS65

Block setpoint and status after ramping, filtering,
and limiting that is provided to a supervisory host
for back calculation to allow action to be taken
under limiting conditions or mode change. Used
when mode is RCAS.
N/A
Dynamic
Data Type: DS65

Block output that is provided to a supervisory host
for a back calculation to allow action to be taken
under limiting conditions or mode change. Used
when mode is RCAS.
MAN
OOS
100
0
%
2
Data Type: DS68

decimal point associated with the external tracking
value (TRK_VAL).
N/A
ALL
ALL
ALL
BAD:
NC:
const
Status
Value
Status
BAD:
NC:
const
Feed Forward Scale

FF_SCALE
41
MAN
OOS
Feed Forward Gain

FF_GAIN
42
MAN
OOS
Data Type: DS66

Discrete input that initiates external tracking of the
block output to the value specified by TRK_VAL.
Value
Data Type: DS65

The value (after scaling from TRK_SCALE to
OUT_SCALE) applied to OUT in LO mode when
external tracking is enabled by TRK_IN_D.
Status
BAD:
NC:
const
Data Type: DS65

The feedforward control input value and status.
Value
-Continued-
136
Initial Value
Data Type: Uint8

Defines action to be taken on remote control
device timeout.
Normal Return - actual mode changes to the next
lowest priority non-remote mode permitted but
returns to the target remote mode when the
remote computer completes the initialization
handshake.
No Return - Target mode changes to the next
lowest priority non-remote mode permitted. The
target remote mode is lost, so no return occurs.
ALL
RO
Range
100
0
%
2
Data Type: DS68

decimal point associated with the feedforward
value (FF_VAL).
Data Type: Float

The feedforward gain value. FF_VAL is multiplied
by FF_GAIN before it is added to the calculated
control output. A value of 0 disables feedforward.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Update Event
UPDATE_EVT
UNACKNOWLEDGED
Index
Number
RO /
RW
Block
Mode
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Update reported
2=Update not reported
Range
Initial Value
43
43.1
UPDATE_STATE
43.2
RO
N/A
TIME_STAMP
43.3
RO
N/A
STATIC_REVISION
43.4
RO
N/A
RELATIVE_INDEX
43.5
RO
N/A
RW
N/A
Block Alarm
BLOCK_ALM
UNACKNOWLEDGED
ALARM_STATE
Data Type: DS73

This alert is generated by any changes to the static
data.
44
44.1
44.2
RO
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clearreported
2=Clearnot reported
3=Active reported
Data Type: DS72

hardware, connection failure, or system problems
in the block. The cause of the alarm will be set in
the subcode.
VALUE Data Type: Unsigned8
TIME_STAMP
44.3
RO
N/A
SUBCODE
44.4
RO
N/A
VALUE
44.5
RO
N/A
Alarm Summary
ALARM_SUM
Description
45
CURRENT
45.1
RO
ALL
UNACKNOWLEDGED
45.2
RO
ALL
UNREPORTED
45.3
RO
ALL
DISABLED
45.4
RW
ALL
1: High High Alarm

2: High Alarm
3: Low Low Alarm
4: Low Alarm
5: Deviation High Alarm
6: Deviation Low Alarm
7: Block Alarm
1: High High Alarm
2: High Alarm
3: Low Low Alarm
4: Low Alarm
5: Deviation High Alarm
6: Deviation Low Alarm
7: Block Alarm
Acknowledge Option
ACK_OPTION
46
N/A
Alarm Hysteresis
ALARM_HYS
47
ALL
0 to 50%
High High Priority

HI_HI_PRI
48
ALL
0 to 15
High High Limit

HI_HI_LIM
49
ALL
PV_SCALE, or +INF
High Priority
HI_PRI
50
ALL
0 to 15
High Limit
HI_LIM
51
ALL
PV_SCALE, or +INF
Low Priority
LO_PRI
52
ALL
0 to 15
Low Limit
LO_LIM
53
ALL
PV_SCALE, or -INF
Low Low Priority

LO_LO_PRI
54
ALL
0 to 15
Dynamic
All bits: 0
0.50%
0
+INF
0
+INF
0
-INF
0
Data Type: DS74

unreported states, and disabled states of the
alarms associated with the function block.

0=Disable
1=Enable
Used to set auto acknowledgment of alarms.
Data Type: Float

The amount the alarm value must return to within
the alarm limit before the associated active alarm
condition clears.
The priority of the HI HI Alarm.
Data Type: Float
The setting for the alarm limit used to detect the
HI HI alarm condition.
The priority of the HI alarm.
Data Type: Float
HI alarm condition.
The priority of the LO alarm.
Data Type: Float
LO alarm condition.
The priority of the LO LO alarm.
-Continued-
137
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Index
Number
RO /
RW
Block
Mode
Range
Initial Value
Low Low Limit

LO_LO_LIM
55
ALL
PV_SCALE, or -INF
Deviation High Priority

DV_HI_PRI
56
ALL
0 to 15
Deviation High Limit

DV_HI_LIM
57
ALL
PV_SCALE, or +INF
Deviation Low Priority

DV_LO_PRI
58
ALL
0 to 15
Deviation Low Limit

DV_LO_LIM
59
ALL
-INF, or -PV span to 0
High High Alarm

HI_HI_ALM
60
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=undefined
0=Undefined
1=Clear reported
3=Active reported
0=undefined
UNACKNOWLEDGED
60.1
RW
0
+INF
0
-INF
ALARM_STATE
60.2
RO
N/A
TIME_STAMP
60.3
RO
N/A
SUBCODE
60.4
RO
N/A
VALUE
60.5
RO
N/A
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=undefined
0=Undefined
1=Clear reported
3=Active reported
0=undefined
High Alarm
HI_ALM
UNACKNOWLEDGED
Data Type: Float

deviation high alarm condition.
The priority of the deviation low alarm.
Data Type: Float
The setting for the alarm limit use to detect the
deviation low alarm condition.
Data Type: DS71

The HI HI alarm data, which includes a value of the
alarm, a timestamp of occurrence, and the state of
the alarm.
61
61.1
61.2
RO
N/A
TIME_STAMP
61.3
RO
N/A
SUBCODE
61.4
RO
N/A
VALUE
61.5
RO
N/A
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=undefined
0=Undefined
1=Clear reported
3=Active reported
0=undefined
UNACKNOWLEDGED

The priority of the deviation high alarm.
VALUE Data Type: Float
ALARM_STATE
Low Alarm
LO_ALM
Data Type: DS71

The HI alarm data, which includes a value of the
the alarm.
62
62.1
ALARM_STATE
62.2
RO
N/A
TIME_STAMP
62.3
RO
N/A
SUBCODE
62.4
RO
N/A
VALUE
62.5
RO
N/A
Data Type: DS71

The LO alarm data, which includes a value of the
the alarm.
0
-Continued-
138
-INF
Description
Data Type: Float
LO LO alarm condition.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Low Low Alarm
LO_LO_ALM
UNACKNOWLEDGED
Index
Number
RO /
RW
Block
Mode
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=undefined
0=Undefined
1=Clear reported
3=Active reported
0=undefined
Range
Initial Value
63
63.1
ALARM_STATE
63.2
RO
N/A
TIME_STAMP
63.3
RO
N/A
SUBCODE
63.4
RO
N/A
VALUE
63.5
RO
N/A
Deviation High Alarm

DV_HI_ALM
64
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=undefined
0=Undefined
1=Clear reported
3=Active reported
0=undefined
UNACKNOWLEDGED
64.1
64.2
RO
N/A
TIME_STAMP
64.3
RO
N/A
SUBCODE
64.4
RO
N/A
VALUE
64.5
RO
N/A
Deviation Low Alarm

DV_LO_ALM
65
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=undefined
0=Undefined
1=Clear reported
3=Active reported
0=undefined
65.1
Data Type: DS71

The LO LO alarm data, which includes a value of the
the alarm.
ALARM_STATE
UNACKNOWLEDGED
Description
Data Type: DS71

The DV HI alarm data, which includes a value of the
the alarm.
ALARM_STATE
65.2
RO
N/A
TIME_STAMP
65.3
RO
N/A
SUBCODE
65.4
RO
N/A
VALUE
65.5
RO
N/A
Data Type: DS71

The DV LO alarm data, which includes a value of
the alarm, a timestamp of occurrence, and the
state of the alarm.
0
Extended Parameters
Bias
BIAS
66
Error
ERROR
67
RO
SP Work
SP_WRK
68
RO
Data Type: Float

The bias value used to calculate output for a PD
structure.
N/A
Dynamic
Data Type: Float

The error (SP-PV) used to determine the control
action.
N/A
Dynamic
Data Type: Float

The working set point of the block after limiting
and filtering is applied. EU of PV_SCALE
Data Type: Float

The time constant of the firstorder SP filter. It is
the time, in seconds, required for a 63 percent
change in the IN value. Applied after SP rate
limiting.
ALL
OUT_SCALE +/- 10%
SP FTime
SP_FTIME
69
ALL
Positive
Math Form
MATHFORM
70
OOS
0=Standard
1=Series
0=Standard

Selects equation form (series or standard)
-Continued-
139
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Structureconfig
STRUCTURECONFIG
UGamma
GAMMA (ugamma)
Index
Number
RO /
RW
71
72
Block
Mode
Range
Initial Value
OOS
0=PID terms on error

1=PI terms on error, D term
on PV
2=I terms on error, PD term
on PV
3=PD terms on error
4= P term on error, D term
on PV
5=ID terms on error
6=I term on error, D term on
PV
7=2 Deg. of Freedom PID
0=PID terms
on error

Defines PID equation structure to apply controller
action.
1.0
Data Type: Float

Fraction of derivative action taken on error versus
PV. For a value of 0.6, then 60% of the derivative
action will be based on error and 40% on PV. The
value of GAMMA may be changed over a range of
0-1 if STRUCTURE is set to Two Degrees of
Freedom Control. Otherwise, it is automatically set
to a value of 1 or 0 based on the Structure
selection.
1.0
Data Type: Float

Fraction of proportional action taken on error
versus PV. For a value of 0.6, then 60% of the
proportional action will be based on error and 40%
on PV. The value of BETA may be changed over a
range of 0-1 if STRUCTURE is set to Two Degrees of
Freedom Control. Otherwise, it is automatically set
to a value of 1 or 0 based on the Structure
selection.
OOS
> = 0, < = 1
Description
UBeta
BETA (ubeta)
73
OOS
> = 0, < = 1
IDeadBand
IDEADBAND
74
OOS
Positive
StdDev
STDDEV
75
RO
N/A
Dynamic
Data Type: Float

Standard deviation of PV.
Cap StdDev
CAP_STDDEV
76
RO
N/A
Dynamic
Data Type: Float

Standard deviation of PV changes.
T Request
T_REQUEST
77
RO
ALL
T State
T_STATE
78
RO
NONE
T Status
T_STATUS
79
RO
N/A
0=Request Tuning
1=Force Tuning
2=Reset Tuner
0=Scan Rate Too Low

Warning
1=Insufficient Process
Response (obsolete)
2=Scan Rate Too High
Warning
3=Inverse Direct Acting
Error
4=PV Deviation Too Large
5=Initial PV Deviation Too
Large
6=PV Limited or Constant
7=PV Bad
8=Invalid Mode for Tuning
9=BKCAL_IN Non Good or
Limited
10=Out Limited
11=Bypass Active
12=Mode Changed
13=Tracking Active
14=Disconnected
15=SP Changed
-Continued-
140
Data Type: Float

Integral action stops when ERROR is within
IDEADBAND, proportional and derivative action
continue. EU of PV_SCALE

Operator request to initiate/control autotuning.

Current autotuner state.

Autotuner status.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
T Ipgain
T_IPGAIN
Index
Number
RO /
RW
Block
Mode
Range
Initial Value
Description
80
RO
N/A
0.0
Data Type: Float

Integrated process gain.
T Ugain
T_UGAIN
81
RO
N/A
0.0
Data Type: Float

Ultimate gain.
T Uperiod
T_UPERIOD
82
RO
N/A
0.0
Data Type: Float

Ultimate period.
T Psgain
T_PSGAIN
83
RO
N/A
0.0
Data Type: Float

Process static gain.
T Ptimec
T_PTIMEC
84
RO
N/A
0.0
Data Type: Float

Process time constant.
T Pdtime
T_PDTIME
85
RO
N/A
0.0
Data Type: Float

Process dead time.
T Targetop
T_TARGETOP
86
ALL
T Hyster
T_HYSTER
87
ALL
> = 0.0
0.0
Data Type: Float

Hysteresis
T Relayss
T_RELAYSS
88
ALL
> = 0.0
3.0
Data Type: Float

Relay step size.
T Gain Magnifier
T_GAIN_MAGNIFIER
89
ALL
> 0.1, < 100
1.0
Data Type: Float

Scales amount of gain.
T Auto Extra DT
T_AUTO_EXTRA_DT
90
ALL

Allow additional cycle with extra deadtime.
T Auto Hysteresis
T_AUTO_HYSTERESIS
91
ALL

Allows calculation of hysteresis based on
CAP_STDDEV
T Aoperiods
T_AOPERIODS
92
N/A

Actual oscillation periods.
RO

Target oscillation periods.
View Lists
Table 433. PID Function Block, View 1
Index Number
1
Parameter

Index Number
Parameter
ST_REV
ST_REV
5.1
10
PV_SCALE
5.2
11
OUT_SCALE
5.3
12.1
GRANT_DENY.GRANT
5.4
12.2
GRANT_DENY.DENY
BLOCK_ERR
17
BYPASS
PV
21
SP_HI_LIM
SP
22
SP_LO_LIM
OUT
28
OUT_HI_LIM
18
CAS_IN
29
OUT_LO_LIM
38
TRK_IN_D
39
TRK_VAL
45.1
ALARM_SUM.CURRENT
45.2
45.3
45.4
ALARM_SUM.DISABLED
141
Instruction Manual

August 2012
D103412X012

Index Number
1
Parameter
ST_REV
5.1
5.2
5.3
5.4
BLOCK_ERR
PV
SP
OUT
15
IN
18
CAS_IN
27
BKCAL_IN
31
BKCAL_OUT
32
RCAS_IN
33
ROUT_IN
35
RCAS_OUT
36
ROUT_OUT
38
TRK_IN_D
39
TRK_VAL
40
FF_VAL
45.1
ALARM_SUM.CURRENT
45.2
45.3
45.4
ALARM_SUM.DISABLED
67
ERROR
68
SP_WORK
71
STRUCTURECONFIG
75
STDDEV
76
CAP_STDDEV
Table 436. PID Function Block, View 4.1

Index Number
Parameter
ST_REV
STRATEGY
ALERT_KEY
13
CONTROL_OPTS
14
STATUS_OPTS
16
PV_FTIME
19
SP_RATE_DN
20
SP_RATE_UP
23
GAIN
24
RESET
25
BAL_TIME
26
RATE
30
BKCAL_HYS
34
SHED_OPT
37
TRK_SCALE
41
FF_SCALE
42
FF_GAIN
46
ACK_OPTION
47
ALARM_HYS
48
HI_HI_PRI
49
HI_HI_LIM
50
HI_PRI
51
HI_LIM
52
LO_PRI
53
LO_LIM
54
LO_LO_PRI
55
LO_LO_LIM
56
DV_HI_PRI
57
DV_HI_LIM
58
DV_LO_PRI
59
DV_LO_LIM
Table 437. PID Function Block, View 4.2

Index Number
Note
Because individual views are limited in size, View List 4 has
two parts.
142
Parameter
ST_REV
66
BIAS
69
SP_FTIME
70
MATHFORM
71
STRUCTURECONFIG
72
GAMMA (ugamma)
73
BETA
74
IDEADBAND
Instruction Manual
D103412X012
August 2012

PID FUNCTION BLOCK
Quick Config
Alert Key
Control Options
Deviation Low Limit
Gain
High High Limit
High Limit
Low Limit
Low Low Limit
Output Scale: EU at 100%
Output Scale: Units Index
Output Scale: Decimal
Reset
Setpoint: Status
Setpoint: Value
Setpoint High Limit
Setpoint Low Limit
Common Config
Alarm Hysteresis
Alert Key
Control Options
Deviation Low Limit
Gain
High High Limit
High Limit
Low Limit
Low Low Limit
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Output High Limit
Output Low Limit
Rate
Reset
Setpoint: Status
Setpoint: Value
Setpoint High Limit
Setpoint Low Limit
Advanced Config
Feed Forward Gain
Feed Forward Scale: EU at 100%
Feed Forward Scale: Units Index
Feed Forward Scale: Decimal
Shed Options
Setpoint Rate Down
Setpoint Rate Up
Static Revision
Status Options
Strategy
Tracking Scale: EU at 100%
Tracking Scale: Units Index
Tracking Scale: Decimal
Tracking Value: Status
Tracking Value: Value
Connectors
Back Calculation Input: Status
Back Calculation Intput: Value
Feed Forward Value: Status
Feed Forward Value: Value
Input: Status
Input: Value
Output: Status
Ouput: Value
Tracking Input Discrete: Status
Tracking Input Descrete: Value
Online

Back Calculation Intput: Value
Block Error
Bypass
Gain
Input: Status
Input: Value
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Output: Status
Output: Value
Remote Out Input: Status
Remote Out Input: Value
Remote Out Output: Status
Remote Out Output: Value
Setpoint: Status
Setpoint: Value
Status
Block Error
(menu continued on next page)
143
Instruction Manual

August 2012
D103412X012
All
PID FUNCTION BLOCK cont.

Other
Tag Description
Grant Deny: Grant
Grant Deny: Deny
Balance Time
Block Alarm: Value
Alarm Summary: Current
Alarm Summary: Unacknowledged
Alarm Summary: Unreported
Alarm Summary: Disabled
Acknowledge Option
High High Alarm: Unacknowledged
High High Alarm: Alarm State
High High Alarm: Time Stamp
High High Alarm: Subcode
High High Alarm: Float Value
High Alarm: Unacknowledged
High Alarm: Alarm State
High Alarm: Time Stamp
High Alarm: Subcode
High Alarm: Float Value
Low Alarm: Unacknowledged
Low Alarm: Alarm State
Low Alarm: Time Stamp
Low Alarm: Subcode
Low Alarm: Float Value
Low Low Alarm: Unacknowledged
Low Low Alarm: Alarm State
Low Low Alarm: Time Stamp
Low Low Alarm: Subcode
Low Low Alarm: Float Value
Deviation High Alarm: Unacknowledged
Deviation High Alarm: Alarm State
Deviation High Alarm: Time Stamp
Deviation High Alarm: Subcode
Deviation High Alarm: Float Value
Deviation Low Alarm: Unacknowledged
Deviation Low Alarm: Alarm State
Deviation Low Alarm: Time Stamp
Deviation Low Alarm: Subcode
Deviation Low Alarm: Float Value
Bias
144
Other
(continued)
Error
SP Work
SP FTime
mathform
structureconfig
Ugamma
UBeta
IDeadBand
StdDv
Cap StdDev
T Request
T State
T Status
T Ipgain
T Ugain
T Uperiod
T Psgain
T Ptimec
T Pdtime
T Targetop
T Hyster
T Relayss
T Gain Magnifier
T Auto Extra DT
T Auto Hysteresis
T Aoperiods
Characteristics: Block Tag

Static Revision
Tag Description
Strategy
Alert Key
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Block Error
Setpoint: Status
Setpoint: Value
Output: Status
Output: Value
Grant Deny: Grant
Grant Deny: Deny
Control Options
Status Options
Input: Status
Input: Value
Bypass
Setpoint Rate Down
Setpoint Rate Up
Setpoint High Limit
Setpoint Low Limit
Gain
Reset
Balance Time
Rate
Back Calculation Input: Value
Output High Limit
Output Low Limit
Remote Out Input: Status
Remote Out Input: Value
Shed Options
Remote Out Output: Status
Remote Out Output: Value
Tracking Scale EU at 0%
Tracking Scale: Units Index
Tracking Scale: Decimal
Feed Forward Scale: Units Index
Feed Forward Scale: Decimal
Feed Forward Gain
All (continued)
All (continued)
Updated Event: Unacknowledged

Block Alarm: Value
Acknowledge Option
Alarm Hysteresis
High High Priority
High High Limit
High Priority
High Limit
Low Priority
Low Limit
Low Low Priority
Low Low Limit
Deviation High Priority
Deviation Low Priority
Deviation Low Limit
High Alarm: Subcode
Low Alarm: Subcode
Deviation High Alarm: Unacknowledged
Deviation High Alarm: Alarm State
Deviation High Alarm: Time Stamp
Deviation High Alarm: Subcode
Deviation High Alarm: Float Value
Deviation Low Alarm: Unacknowledged
Deviation Low Alarm: Alarm State
Deviation Low Alarm: Time Stamp
Deviation Low Alarm: Subcode
Deviation Low Alarm: Float Value
Bias
Error
SP Work
SP FTime
mathform
structureconfig
UGamma
UBeta
IDeadBand
StdDev
Cap StdDev
T Request
T State
T Status
T Ipgain
T Ugain
T Uperiod
T Psgain
T Ptimec
T Pdtime
T Targetop
T Hyster
T Relayss
T Gain Magnifier
T Auto Extra DT
T Auto Hysteresis
T Aoperiods
Instruction Manual
Detailed SetupISEL Function Block
D103412X012
August 2012
Input Selector Function Block

Overview
The Input Selector (ISEL) function block (figure 412) can be used to select the first good, maximum, minimum,
average, or hot backup from as many as eight input values and place it at the output. The block supports signal status
propagation. There is no process alarm detection in the Input Selector function block. Figure 413 illustrates the
internal components of the ISEL function block. Table 440 lists the ISEL block parameters, their index numbers, and
descriptions.
Figure 412. Input Selector Function Block
OUT
IN (18)
DISABLE (18)
OUT_D
OP_SELECT
ISEL
SELECTED
SELECTED
OUT
OUT_D
= Input used in the selection algorithm.

= Discrete input used to enable or disable
the associated input channel.
= Input used to override algorithm.
= The selected channel number.
.
= The block output and
status.
= Discrete output that signals
a selected alarm condition.
FIELDBUS_56A
IN_1
IN_2
IN_3
IN_4
IN_5
IN_6
IN_7
IN_8
DISABLE_1
DISABLE_2
DISABLE_3
DISABLE_4
DISABLE_5
DISABLE_6
DISABLE_7
DISABLE_8
OP_SELECT
Modes
The ISEL function block supports three modes of operation as defined by the MODE_BLK [5] parameter:
Manual (Man)The block output (OUT [7]) may be entered manually.
Automatic (Auto)OUT [7] reflects the selected input value.
Out of Service (OOS)The block is not processed. The BLOCK_ERR [6] parameter shows Out of Service. In this
mode, you can make changes to all configurable parameters. The target mode of a block may be restricted to one
or more of the supported modes.
The Input Selector block Actual mode will be Out of Service if any of the following are true:
The Actual mode of the resource block is not Auto
The Input Selector block Target mode is Out of Service
145
Instruction Manual

August 2012
D103412X012
The Input Selector block Target mode is Auto, OP_SELECT [22] is not being used, and SELECT_TYPE [19] is 0. In this
case, the BLOCK_ERR [6] parameter shows a Block Configuration Error.
The Input Selector block Actual mode will be Manual if all of the above is not true and the Target mode is Manual.
Figure 413. Input Selector Function Block Schematic
IN_1
IN_2
IN_3
AUTO
Selection
Algorithm
IN_4
OUT
MAN
DISABLE_1
SELECTED
DISABLE_2
DISABLE_4
OP_SELECT
SEL_TYPE
MIN_GOOD
fieldbusfbus_229a
DISABLE_3
SELECT_TYPE
NOTE: THIS FIGURE DOES NOT INCLUDE THE ADDITIONAL
4 INPUTS IN THE EXTENDED PARAMETERS.
Status Handling
Quality Use and Propagation
In Auto mode, OUT [7] reflects the value and status of the selected input based on the following criteria:
A bad or disabled input is never used by any of the selection algorithms
For a selection algorithm to use an input with status of Uncertain, the STATUS_OPTS [10] parameter must have
Use Uncertain as Good.
STATUS_OPTS [10] is applied before selection.
If the number of good inputs is less than MIN_GOOD [20], or if the number of inputs evaluated is 0, the status of
OUT [7] and SELECTED [21] will be Bad.
If an input is disabled or its status is Bad and is selected via OP_SELECT [22], then the status of OUT [7] and
SELECTED [21] will be Bad. If the quality of the input is Uncertain, and the selection for the STATUS_OPTS [10]
parameter is Use Uncertain as Good, then the status of OUT [7] and SELECTED [21] will be Uncertain. Otherwise
the status of OUT [7] and SELECTED [21] will be Good Noncascade.
146
Instruction Manual
D103412X012
August 2012
When the block is in the Manual mode the status and substatus of OUT [7] and SELECTED [21] will be as follows:
Substatus will be nonspecific and the limit will be constant.
Quality of OUT [7] and SELECTED [21] will be Uncertain if STATUS_OPTS [10] is Uncertain if in Manual mode.
Otherwise, the quality of OUT [7] and SELECTED [21] will be Good Noncascade.
Limit Propagation
Refer to figure 414. When SELECT_TYPE [19] is Average, Not Limited is propagated unless all inputs have the same
limit status. If ll inputs have the same limit status, the limit status of the inputs is propagated.
If SELECT_TYPE [19] is Middle and the number of inputs used by the algorithm is greater than one: Not Limited is
propagated unless all selected inputs have the same limit status, in which case the limit status of the inputs is
propagated.
If SELECT_TYPE [19] is Middle and a single input, or if Maximum or Minimum then: If the selected input is a constant
and Middle, Constant is propagated. Otherwise, if the selected input is a constant and Maximum or Minimum,
propagate low if Maximum, propagate high if Minimum. If the selected input is not a constant, propagate selected
input limit as is.
When SELECT_TYPE [19] is First Good or Hot Spare or if OP_SELECT [22] is nonzero, propagate selected input limit as
is.
Substatus Propagation
Refer to figure 415. For SELECT_TYPE [19] of Maximum, Minimum, First Good, Hot Spare, and Middle with only one
input, simply propagate substatus as is.
For SELECT_TYPE [19] of Maximum and Minimum with more than one input with the same value, propagate substatus
if all inputs are the same.
For SELECT_TYPE [19] of Average or Middle with more than one input, propagate NonSpecific.
If the status of OUT [7] is Bad, then the substatus will be as follows:
Out of Service if the Target mode is Out of Service.
Configuration Error with a BLOCK_ERR [6] of Configuration Error if the Actual mode is Out of Service.
Otherwise a substatus of NonSpecific.
147
Instruction Manual

August 2012
D103412X012
Figure 414. Input Selector Block Limit Propagation

START
Propagate
selected input
limit status
No
OP_SELECT
equal to zero?
Yes
SELECT_TYPE
Average?
Yes
All inputs with

same limit
status?
Yes
No
No
Propagate
Not Limited
Yes
SELECT_TYPE
Middle?
More than 1
input?
Yes
No
No
All inputs with

same limit
status?
Yes
Propagate that
limit status
No
Propagate
Not Limited
Input a
constant?
Yes
Propagate
Constant
No
SELECT_TYPE
Maximum?
Yes
Yes
Propagate
Low Limit
Yes
Propagate
High Limit
No
No
SELECT_TYPE
Minimum?
Input a
constant?
Yes
No
No
SELECT_TYPE
First Good or Hot
Spare?
Input a
constant?
Yes
Propagate
selected input
limit status
No
Illegal Select Type

should never be reached
148
NOTES:
1
LIMIT
MANIPULATION FOR A CONSTANT INPUT FOR MAXIMUM AND MINIMUM IS BASED
UPON THE FOUNDATION FIELDBUS SPECIFICATION. THE REASONING IS BASED ON HIGH SELECT
PROVIDING A LOW LIMIT STATUS AND LOW SELECT PROVIDING A HIGH LIMIT STATUS.
Instruction Manual
D103412X012
August 2012
Figure 415. Input Selector Block Substatus Propagation

START
Yes
MODE_BLK
OOS?
Propagate Bad,
Out of Service
No
STATUS_OPTS Un
certain if Man
Mode?
Yes
MODE_BLK
MAN?
No
Yes
Propagate
Uncertain
No
Propagate Good
Noncascade
MODE_BLK must
be Auto
1
OP_SELECT
status?
Bad
Propagate Bad,
Nonspecific
Good
1
OP_SELECT
value >0?
Yes
Propagate Good
Noncascade
Bad
No
At least 1 good
input?
Good
Selected in
put status?
No
Propagate Bad,
Nonspecific
Yes
SELECT_TYPE
Middle or
Average?
Yes
One input?
Multiple
Inputs
No
SELECT_TYPE
Maximum or
Minimum?
Yes
Yes
One input?
Propagate
Nonspecific
Yes
Multiple
Inputs
No
All inputs with

same value?
SELECT_TYPE Must
be First Good or
Hot Spare?
Yes
Propagate input
substatus as is
Propagate input
substatus as is
No
Propagate
Nonspecific
No
Illegal Select Type
should never be reached
Yes
NOTES:
AN INPUT STATUS MAY BE BAD, GOOD, OR UNCERTAIN. IF BAD, THE INPUT IS NOT USED AND THE STATUS IS PROPAGATED
AS BAD WITH SUBSTATUS NONSPECIFIC. IF GOOD IT IS USED AND THE STATUS IS PROPAGATED AS GOOD
(NONCASCADE). IF UNCERTAIN, AND STATUS_OPTS IS USE UNCERTAIN AS GOOD THEN THE INPUT IS USED AND THE
STATUS IS PROPAGATED AS GOOD (NONCASCADE), OTHERWISE IT IS NOT USED AND THE STATUS IS PROPAGATED AS
BAD WITH SUBSTATUS NONSPECIFIC.
149
Instruction Manual
August 2012
D103412X012
STATUS_OPTS Supported
In the STATUS_OPTS [10] parameter, you can select from the following options to control the status handling:
Use Uncertain as Goodsets the OUT [7] status to Good when the selected input status is Uncertain.
Uncertain if in Manual mode: sets the OUT [7] status to Uncertain when the mode is Manual.
Note
The block mode must be Out of Service to set STATUS_OPTS [10].
Input Selection
The ISEL function block reads the values and statuses of as many as eight inputs (IN_1 [11], IN_2 [12], IN_3 [13], IN_4
[14], IN_5 [25], IN_6 [26], IN_7 [27], IN_8 [28]). To use any of the six selection algorithms to select the output,
OP_SELECT [22] must be 0. To specify which algorithm to use, configure the selector type parameter (SELECT_TYPE
[19]) as follows:
Maximumselects the input with the highest value from the inputs that are not bad and not disabled.
Minimumselects the input with the lowest value from the inputs that are not bad and not disabled.
Averagecalculates the average value of the inputs that are not bad and not disabled and provides it as the output.
For example, if the number used to average (AVG_USE [33]) is 4 and the number of connected inputs is 6, then the
highest and lowest values would be dropped prior to calculating the average. If AVG_USE [33] is 2 and the number
of connected inputs is 7, then the two highest and lowest values would be dropped prior to calculating the average
and the average would be based on the middle three inputs.
MiddleIf the number of good usable inputs is odd, then it selects the middle value. If the number of good usable
inputs is even, then it averages the middle two values and selects status as worst of two. If both inputs' limit status
are not the same then it sets limit status of Not Limited.
First Goodselects the first input that is not bad and not disabled, starting with IN_1 [11].
Hot Spareinitially uses the input selected as first good. If the selected input goes bad, the first good selection is
repeated. If the selected input remains good, it stays selected. If the originally selected input returns to good status
the selection does not change. Selection changes only if the currently selected input goes bad.
Disabling Inputs
Use the parameters DISABLE_1 [15], DISABLE_2 [16], DISABLE_3 [17], DISABLE_4 [18], DISABLE_5 [29], DISABLE_6
[30], DISABLE_7 [31] and DISABLE_8 [32] to disable the corresponding inputs. An input that is disabled will not be used
by any of the selection algorithms.
The status of the disable parameter must be Good, Good_Cascade, or Uncertain with a STATUS_OPTS [10] of
Use Uncertain as Good in order to be evaluated. If the status of the disable parameter is Bad, its last usable value is
maintained and acted upon. If the device restarts, losing the last usable value, the last usable value is set to disabled.
150
Instruction Manual
D103412X012

August 2012
IN_1 through IN_8 and DISABLE_1 through DISABLE_8 are nonvolatile type parameters so if they are Linked they will
automatically have Bad status until connections are reestablished. If they are not Linked, they will be restored with the
previous value from NVM across device restarts.
Direct Selection of Inputs

The parameter OP_SELECT [22] can be used to select a particular input. If OP_SELECT [22] is nonzero, the selection
algorithm is bypassed and the value of OP_SELECT [22] is interpreted as the input number to select. If the OP_SELECT
[22] value is greater than the number of inputs, then the highest input is selected. The status of OP_SELECT [22] must
be Good, Good_Cascade, or Uncertain with a STATUS_OPTS [10] of Use Uncertain as Good in order to be
evaluated. If the status of OP_SELECT [22] is Bad, then the OUT [7] status is Bad.
Identification of Selected Inputs

For a SELECT_TYPE [19] of Maximum, Minimum, Middle, First Good, and Hot Spare, SELECTED [21] indicates the
number of the selected input. When Middle is computed from more than one input, SELECTED [21] is set to 0.
For a SELECT_TYPE [19] of Average, SELECTED [21] indicates the number of inputs used in the average calculation.
When the block mode is Manual, SELECTED [21] is set to 0.
Alarm Detection
A block alarm will be generated whenever the BLOCK_ERR [6] has an error bit set. The types of block error for the PID
block are defined above.
Process alarm detection is based on OUT [7] value. You can configure the alarm limits of the following standard
alarms:
High (HI_LIM [40])
Low (LO_LIM [42])
of the PV span can be set using the ALARM_HYS [36] parameter. The priority of each alarm is set in the following
parameters:
HI_PRI [39]
HI_HI_PRI [37]
LO_PRI [41]
LO_LO_PRI [43]
ACK_OPTION [35] is used to set automatic acknowledgement of alarms.
ALARM_SUM [34] indicates the current alert status, unacknowledged states, and disabled states of the alarms
associated with the function block.
151
Instruction Manual

August 2012
D103412X012
Table 438. ISEL Function Block Alarm Priorities
Priority Number
0
The priority of an alarm condition changes to 0 after the condition that caused the alarm is corrected.
An alarm condition with a priority of 1 can be recognized by the system. The device monitors the alarm but does not report it
until requested by the host system.
3-7
8-15
1. The priority classes advise and critical have no relationship to Plant Web Alerts.
Block Errors
ISEL block and are provided only for your reference.
Condition Number
Other (N/A)
Block Configuration Error If OP_SELECT is not being used, and SELECT_TYPE = 0. This implies OP_SELECT status is good and actual
mode is AUTO.
Simulate Active (N/A)
Input failure/process variable has Bad status Set if any IN or any DISABLE or OP_SELECT is bad and connected. This means that a
status of BAD NC would not cause an input failure but a status of BAD LUV or BAD no LUV would cause and input failure.
Output failure Set if OUT quality is bad and the Actual mode is not Out of Service.
10
11
Lost NV Data (N/A)
12
13
14
Power Up Set if the Target mode is Out of Service when powered up until the mode is changed.
15
Out of Service The block is in Out of Service (OOS) mode
ISEL Function Block Parameter List (table 440)

Double indentations and shaded Index Numbers indicate subparameters
152
Instruction Manual
D103412X012
August 2012
Table 440. Input Selector Function Block Parameter Definitions

Label
PARAMETER_NAME
Index
Number
RO / RW
Block
Mode
Range
Initial
Value
Description
Static Revision
ST_REV
RO
N/A
0 to 65535

The revision level of the static data associated with the
function block. The revision value will be incremented
each time a static parameter value in the block is
changed.
Tag Description
TAG_DESC
RW
ALL
7 bit ASCII
spaces

The user description of the intended application of the
block.
Strategy
STRATEGY
RW
ALL
0 to 65535

The strategy field can be used to identify grouping of
blocks. This data is not checked or processed by the
block.
Alert Key
ALERT_KEY
RW
ALL
1 to 255

information may be used in the host for sorting alarms,
etc.
Block Mode
MODE_BLK
TARGET
5.1
RW
ALL
ACTUAL
5.2
RO
ALL
PERMITTED
5.3
RW
ALL
NORMAL
5.4
RW
ALL
Block Error
BLOCK_ERR
Output
OUT
Output Range
OUT_RANGE
Grant Deny
GRANT_DENY
RO
N/A
MAN
OOS
ALL
GRANT
9.1
ALL
DENY
9.2
ALL
Status Options
STATUS_OPTS
Input 1
IN_1
Input 2
IN_2
10
11
12
OOS
ALL
ALL
OOS, MAN, AUTO
OOS until
block is
configured,
then last
valid target
OOS+MAN+AUTO
OOS+MAN
+AUTO
Data Type: DS69

Valid Bits: 7: OOS, 4: MAN,
3: AUTO
The actual, target, permitted, and normal modes of the
block.
AUTO
1: Block
Configuration Error
7: Input Failure / Bad
PV status
8: Output Failure
14: Power Up
15: OutofService
Status
OUT_RANGE
Dynamic

0=Inactive
1=Active
This parameter reflects the error status associated with
the hardware or software components associated with
a block. It is a bit string, so that multiple errors may be
shown.
Dynamic
Data Type: DS65

Value
EU at 100%
EU at 0%
Units Index
Decimal Point
0: Program
1: Tune
2: Alarm
3: Local
100
0
%
2
All bits: 0
All bits:0
2: Use Uncertain as
GOOD
8: Uncertain if MAN
All bits: 0
Status
BAD
NC
constant
Value
Status
BAD
NC
constant
Value
Data Type: DS67

High and low scale values, engineering units code, and
number of digits to the right of the decimal point
associated with OUT.
Data Type: DS70
Options for controlling access of host computers and
local control panels to operating, tuning, and alarm
parameters of the block. Not used by device.
DENY: 0=N/A, 1=denied
Allows you to select options for status handling and
processing. The supported status option for the input
selector block is: Use Uncertain as Good, Uncertain
if Man mode.
Data Type: DS65
The block input value and status.
Data Type: DS65

0
-Continued-
153
Instruction Manual

August 2012
D103412X012
Table 440. Input Selector Function Block Parameter Definitions (Continued)

Label
PARAMETER_NAME
Input 3
IN_3
Input 4
IN_4
Disable Analog Input 1

DISABLE_1
Index
Number
RO / RW
13
Block
Mode
ALL
14
ALL
15
ALL
Range
BAD
NC
constant
Status
Value
Status
BAD
NC
constant
Value
Status
BAD
NC
constant
Value
0=Use
1=Disable
16
ALL
Value
0=Use
1=Disable
17
ALL
Value
0=Use
1=Disable
18
ALL
Data Type: DS66

Enable/Disable for Input_2, If parameter is TRUE then
input is disabled. If parameter status is BAD it is not
evaluated.
Data Type: DS66

evaluated.
Data Type: DS66

evaluated.

The minimum number of inputs which are good is
less than the value of MIN_GOOD then set the OUT
status to bad.
Min Good
MIN_GOOD
20
ALL
1-4
0 initial value only
Selected
SELECTED
21
Status
Value
0-8
Dynamic
Data Type: DS66

The integer indicating the selected input number.
Status
BAD
NC
constant
Data Type: DS66

An operator settable parameter to force a given input
to be used.
Value
0-8
ALL
-Continued-
154
Data Type: DS66

evaluated.

Determines the selector action
ALL
22
Data Type: DS65

19
N/A
Data Type: DS65

Select Type
SELECT_TYPE
RO
Description
Value
0=Use
1=Disable
1=First Good
2=Minimum
3=Maximum
4=Middle
5=Average
6=Hot Spare
Operator Select
OP_SELECT
0
BAD
NC
constant
Status
DISABLE_4
0
BAD
NC
constant
Status
DISABLE_3
0
BAD
NC
constant
Status
DISABLE_2
Initial
Value
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Update Event
UPDATE_EVT
UNACKNOWLEDGED
Index
Number
RO / RW
Block
Mode
Range
Initial
Value
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Update Reported
2=Updated not
reported
23
23.1
RW
UPDATE_STATE
23.2
RO
N/A
TIME_STAMP
23.3
RO
N/A
STATIC_REVISION
23.4
RO
N/A
RELATIVE_INDEX
23.5
RO
N/A
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clear reported
3=Active reported
4=Active not
reported
Block Alarm
BLOCK_ALM
UNACKNOWLEDGED
Description
Data Type: DS73

This alert is generated by any change to the static data.
24
24.1
ALARM_STATE
24.2
RO
N/A
TIME_STAMP
24.3
RO
N/A
SUBCODE
24.4
RO
N/A
VALUE
24.5
RO
N/A
Data Type: DS72

The block alarm is used for all configuration, hardware,
connection failure, or system problems in the block.
The cause of the alert is entered in the subcode field.
The first alert to become active will set the active
status in BLOCK_ERR. As soon as the Unreported status
is cleared by the alert reporting task, another block
alert may be reported without clearing the Active
status, if the subcode has changed.
Extended Parameters
In 5
IN_5
In 6
IN_6
In 7
IN_7
25
26
27
ALL
ALL
ALL
BAD
NC
constant
Status
Value
Status
BAD
NC
constant
Data Type: DS65

Input value and status.
Data Type: DS65

Value
Status
BAD
NC
constant
Data Type: DS65

BAD
NC
constant
Data Type: DS65

Value
In 8
IN_8

DISABLE_5
28
29
ALL
ALL
Status
Value
Status
BAD
NC
constant
Value
0=Use
1=Disable
BAD
NC
constant
0
Status
DISABLE_6
30
ALL
Value
0=Use
1=Disable
Data Type: DS66

evaluated.
Data Type: DS66

evaluated.
-Continued-
155
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Index
Number
RO / RW
Block
Mode
Range
BAD
NC
constant
Value
DISABLE_7
31
ALL
Status
0=Use
1=Disable
Number used to average

AVG_USE
Alarm Summary
ALARM_SUM
32
ALL
33
0
BAD
NC
constant
Value
DISABLE_8
Initial
Value
Status
0=Use
1=Disable
1 to 8
Description
Data Type: DS66
evaluated.
Data Type: DS66

evaluated.
Number used to average the output. The number of
min and max dropped is the number of inputs minus
AVG_USE.
34
CURRENT
34.1
RO
NA
UNACKNOWLEDGED
34.2
RO
NA
UNREPORTED
34.3
RO
NA
DISABLED
34.4
RW
ALL
Data Type: DS74

unreported states, and disabled states of the alarms
associated with the function block.
1: Hi Hi
2: Hi
3: Lo Lo
4: Lo

Selection of whether alarms associated with the block
will be automatically acknowledged.
0=Disable
1=Enable
ALL
1: Hi Hi
2: Hi
3: Lo Lo
4: Lo
36
ALL
0 to 50%
0.50%
High High Priority

HI_HI_PRI
37
ALL
0 TO 15

Priority of the alarm
High High Limit

HI_HI_LIM
38
ALL
Data Type: Float

Value of analog input which will generate an alarm
High Priority
HI_PRI
39
ALL

High Limit
HI_LIM
40
ALL
Data Type: Float

Low Priority
LO_PRI
41
ALL

Low Limit
LO_LIM
42
ALL
Data Type: Float

Low Low Priority

LO_LO_PRI
43
ALL

Low Low Limit

LO_LO_LIM
44
ALL
Data Type: Float

High High Alarm

HI_HI_ALM
45
Acknowledge Option
ACK_OPTION
35
Alarm Hysteresis
ALARM_HYS
UNACKNOWLEDGED
45.1
RW
0 TO 15
0 TO 15
0 TO 15
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clear reported
3=Active reported
4=Active not
reported
156
ALARM_STATE
45.2
RO
N/A
TIME_STAMP
45.3
RO
N/A
SUBCODE
45.4
RO
N/A
VALUE
45.5
RO
N/A
0
-Continued-
Data Type: Float

Hysteresis on alarms
Data Type: DS71

The high high alarm data, which includes a value of the
alarm, a timestamp of occurrence, and the state of the
alarm.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
High Alarm
HI_ALM
UNACKNOWLEDGED
Index
Number
RO / RW
Block
Mode
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clear reported
3=Active reported
4=Active not
reported
Range
Initial
Value
46
46.1
ALARM_STATE
46.2
RO
N/A
TIME_STAMP
46.3
RO
N/A
SUBCODE
46.4
RO
N/A
VALUE
46.5
RO
N/A
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clear reported
3=Active reported
4=Active not
reported
Low Alarm
LO_ALM
UNACKNOWLEDGED
47.1
47.2
RO
N/A
TIME_STAMP
47.3
RO
N/A
SUBCODE
47.4
RO
N/A
VALUE
47.5
RO
N/A
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clear reported
3=Active reported
4=Active not
reported
UNACKNOWLEDGED
Data Type: DS71

The low alarm data, which includes a value of the
alarm.
48
48.1
ALARM_STATE
48.2
RO
N/A
TIME_STAMP
48.3
RO
N/A
SUBCODE
48.4
RO
N/A
VALUE
48.5
RO
N/A
Output Discrete
OUT_D
Data Type: DS71

The high alarm data, which includes a value of the
alarm.
47
ALARM_STATE
Low Low Alarm

LO_LO_ALM
Description
49
MAN
OOS
Data Type: DS71

The low low alarm data, which includes a value of the
alarm.
0
Status
Data Type: DS66

Discrete output to indicate a selected alarm value
Value
0, 1
Status
Alarm Select
ALM_SEL
50
ALL
1: Hi Hi
2: Hi
3: Lo Lo
4: Lo
All bits:0

Used to select the process alarm conditions that will
cause the OUT_D parameter to be set.
View Lists
157
Instruction Manual

August 2012
D103412X012
Table 441. ISEL Function Block, View 1
Index Number
Index Number
Parameter
ST_REV
5.1
5.1
5.2
5.2
5.3
5.3
5.4
5.4
BLOCK_ERR
BLOCK_ERR
OUT
OUT
11
IN_1
11
IN_1
12
IN_2
12
IN_2
13
IN_3
13
IN_3
14
IN_4
14
IN_4
15
DISABLE_1
15
DISABLE_1
16
DISABLE_2
16
DISABLE_2
17
DISABLE_3
17
DISABLE_3
18
DISABLE_4
18
DISABLE_4
21
SELECTED
21
SELECTED
22
OP_SELECT
22
OP_SELECT
25
IN_5
25
IN_5
26
IN_6
26
IN_6
27
IN_7
27
IN_7
28
IN_8
28
IN_8
29
DISABLE_5
29
DISABLE_5
30
DISABLE_6
30
DISABLE_6
31
DISABLE_7
31
DISABLE_7
32
DISABLE_8
32
DISABLE_8
34.1
ALARM_SUM.CURRENT
34.1
ALARM_SUM.CURRENT
34.2
34.2
34.3
34.3
34.4
ALARM_SUM.DISABLED
34.4
ALARM_SUM.DISABLED
49

Index Number
158
Parameter
ST_REV
Parameter
ST_REV
OUT_RANGE
9.1
GRANT_DENY.GRANT
9.2
GRANT_DENY.DENY
OUT_D

Index Number
Parameter
ST_REV
STRATEGY
ALERT_KEY
10
STATUS_OPTS
19
SELECT_TYPE
20
MIN_GOOD
33
AVG_USE
35
ACK_OPTION
36
ALARM_HYS
37
HI_HI_PRI
38
HI_HI_LIM
39
HI_PRI
40
HI_LIM
41
LO_PRI
42
LO_LIM
43
LO_LO_PRI
44
LO_LO_LIM
50
ALM_SEL
Instruction Manual
D103412X012
August 2012

INPUT SELECTOR FUNCTION BLOCK
Quick Config
Alert Key
Min Good
Output Range: EU at 100%
Output Range: Units Index
Output Range: Decimal
Select Type
Common Config
Min Good
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Select Type
Advanced Config
Alert Key
Static Revision
Status Options
Strategy
Online
Block Error
Disable Analog Input 1: Status
Disable Analog Input 1: Value
Input 1: Status
Input 1: Value
Input 2: Status
Input 2: Value
Input 3: Status
Input 3: Value
Input 4: Status
Input 4: Value
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Operator Selected: Status
Operator Selected: Value
Output: Status
Output: Value
Selected: Status
Selected: Value
Status
Connectors
Block Error
Disable Analog Input 4 : Value
Input 1: Status
Input 1: Value
Input 2: Status
Input 2: Value
Input 3: Status
Input 3: Value
Input 4: Status
Input 4: Value
Operator Select: Status
Operator Select: Value
Output: Status
Output: Value
Selected: Status
Selected: Value
All
Characteristics
Static Revision
Tag Description
Strategy
Alert Key
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Block Error
Output: Status
Output: Value
Grant Deny: Grant
Grant Deny: Deny
Status Options
Input 1: Status
Input 1: Value
Input 2: Status
Input 2: Value
Input 3: Status
Input 3: Value
Input 4: Status
Input 4: Value
Select Type
Min Good
Selected: Status
Selected: Value
Operator Select: Status
Operator Select: Value
Block Alarm: Value
Analog Input 5: Status
Analog Input 5: Value
Number Used to average
All continued
Acknowledge Option
Alarm Hysteresis
High High Priority
High High Limit
High Priority
High Limit
Low Priority
Low Limit
Low Low Priority
Low Low Limit
High Alarm: Subcode
Low Alarm: Subcode
Alarm Output: Status
Alarm Output: Value
Alarm Select
159
Instruction Manual
Detailed SetupOS Function Block

August 2012
D103412X012
Output Splitter Function Block

Overview
The Output Splitter (OS) block (figure 416) provides the capability to drive two control outputs from a single input.
Each output is a linear function of some portion of the input. Back calculation support is provided using the same linear
function in reverse. Cascade initialization is supported by a decision table for combinations of input and output
conditions.
Figure 416. Output Splitter (OS) Function Block
OS
RCAS IN
CAS IN
OUT 1
OUT 2
This block is normally used in split ranging or sequencing of multiple valve applications. A typical split range
application has both valves closed when the splitter input is 50%. One valve opens fully as the input drops to 0%. The
other valve opens as the input rises above 50%.
A typical sequencing application has both valves closed at 0% input. One valve fully opens as the input rises to 50% and
the other stays shut. The second valve opens as the input rises above 50%, and the first valve may remain open or shut
off quickly.
Because this block is in the control path, it is able to pass limit and cascade initialization information back to the
upstream block. Table 448 lists the OS block parameters and their descriptions, units of measure, and index numbers.
Figures 417 and 418 illustrate the internal components of the OS function block.
160
Instruction Manual
D103412X012
August 2012
Figure 417. Output Splitter Function Block Schematic
IN_ARRAY
OUT_ARRAY
LOCKVAL
RCAS_IN
OUT 1
SP
CAS_IN
Auto
OUT 2
BKCAL_IN_1
RCAS_OUT
BKCAL_IN_2
CAS_OUT
Figure 418. Output Splitter Function Block Schematic Diagram
CAS_IN
F
Setpoint
Limiting SP
"
Setpoint
Rate
Limiting
SP_WRK
"
SP_RATE_DN
SP_RATE_UP
IN_ARRAY
OUT_ARRAY
LOCKVAL
"
Calculate
Ouput
"
BKCAL_OUT
F
F
F
"
"
Balance
Ouput
BAL_TIME
"
BKCAL_IN_2
"
BKCAL_IN_1
"
Shed
Mode
"
"
MODE
"
F
"
Balance
Ouput
"
OUT 1
"
OUT 2
Modes
The Output Splitter function block supports the following actual modes:
161
Instruction Manual
August 2012
D103412X012
Out of Service (OOS)The block is not processed. FIELD_VAL and PV are not updated and the OUT status is set to
Bad: Out of Service. The BLOCK_ERR parameter shows Out of Service. In this mode, you can make changes to all
configured parameters.
By using permitted mode the target mode of a block may be restricted to one or more of the following modes: Cas,
Auto or OOS.
Note
The output splitter function block must be in Auto for the mode to go to CAS.
Initialization Manual (IMan)The output path is not complete (for example, the cascade-to-slave path might not be
open). In IMan mode, OUT tracks BKCAL_IN, which allows for bumpless transfer of control.
Automatic (Auto)The block outputs (OUT_1 and OUT_2) reflect the target operating point specified by the
setpoint (SP) parameter.
Cascade (Cas)The SP parameter is set by another function block through a connection to CAS_IN. The SP value is
used to set the OUT parameters automatically. This is the most frequently used mode in this block.
The block's normal mode is Cascade (Cas). You can isolate the block for testing by using Automatic (Auto) mode and
adjusting the setpoint.
When a block attached to an output requests initialization, one of the following actions might occur:
When the other output is not in Cas mode, the block attached to the input is initialized.
When the other output is in Cas mode, this output returns to the value calculated from its slope in a specified time
period.
Status Handling
Substatus value received at CAS_IN [14] is passed to both outputs, except for those used in the cascade handshake.
An IFS goes to both outputs. The status option IFS if Bad CAS_IN is available.
If the Status Option to Propagate failure is set, the block propagates device failure only if both BKCAL_IN show failed
status. Otherwise the upstream cascade would be broken by a failure at either output.
The statuses of OUT_1 [8] and OUT_2 [9] are determined by the statuses of BKCAL_IN_1 and BKCAL_IN_2 and the
actual mode of the block.
When a BKCAL_IN input sees that its downstream block is not in Cas mode, the Splitter function block sets the
corresponding OUT value to the BKCAL_IN value. However, this may not be the same value that is calculated by the
splitter algorithm. When the mode of the downstream block is changed to Cas, the difference between the calculated
output and the backcalculation input is computed and the difference is added to the calculated output. Next, the
difference is reduced to zero over the time defined by the BAL_TIME parameter.
When both BKCAL_IN_1 and BKCAL_IN_2 indicate that the downstream blocks are not in Cas mode or have Bad status,
the first downstream block that goes to Cas mode causes the upstream block to initialize so that there is no difference
between the calculated output and the backcalculation input. This provides bumpless transfer for the first
downstream block.
162
Instruction Manual
D103412X012
August 2012
Limit Handling
The splitter function block is designed to combine the limit information from the two downstream blocks into limits
for the upstream block. The general principle is to allow the upstream block to continue control for as long as possible.
The upstream block is highlimited (BKCAL_OUT of the Splitter block has highlimited status) when:
Both downstream blocks are highlimited (both BKCAL_INS of the Splitter block have highlimited status)
or
One downstream block is highlimited, the associated output slope is positive, and the other block has Bad status or
is not in Cas mode
or
One downstream block is lowlimited, the associated output slope is negative, and the other block has Bad status or
is not in Cas mode
or
SP is greater than or equal to X22
The upstream block is lowlimited when:
Both downstream blocks are lowlimited
or
One downstream block is lowlimited, the associated output slope is positive, and the other block has Bad status or
is not in Cas mode
or
One downstream block is highlimited, the associated output slope is negative, and the other block has Bad status
or is not in Cas mode
or
SP is less than or equal to X11
Input to Output Mapping

The relationship of each output to the input may be defined by a line. Each line may be defined by its endpoints.
Examples of graphical representations of OUT_1 and OUT_2 vs. SP are shown in figure 419 for a split range and a
sequencing application.
The block has the same SP structure as the PID block, except that there is no limiting applied to the SP. The SP may be
used in Auto mode for testing. The operator would use the output of the PID to accomplish the same purpose. Each
downstream block can be taken out of cascade if it becomes necessary to gain control of them.
The examples shown in figure 419 do not show the full range of possibilities. The lines could overlap like an X, or both
start from the origin but have different slopes. The endpoints do not have to lie within 0-100%. Limits in the external
163
Instruction Manual

August 2012
D103412X012
blocks may effect the useful range of a line. Units of percent are used in the examples because the common
application of this block is to valves, but any units may be used to suit the application.
Figure 419. Split Range and Sequence Operation
Split Range
(X22 , Y22)
100%
Sequencing
(X12 , Y12)
100%
(X11 , Y11)
(X22 , Y22)
OUT_1
OUT_1
OUT_2
OUT_2
0%
(X21 , Y21)
(X12 , Y12)
0%
50%
100%
0%
(X21 , Y21)
(X11 , Y11)
0%
SP
50%
X
100%
SP
The following parameters as paired coordinates are used to specify the output splitter operation:
X11, Y11, X12, Y12
X21, Y21, X22, Y22
Where XnJ is the value of SP associated with OUT_n and Xn1 and Xn2 refer to the 1st and 2nd coordinates of the nth
curve respectively. YnJ is the value of OUT_n and Yn1 and Yn2 refer to the 1st and 2nd coordinates of the nth curve
respectively.
By specifying the coordinates as shown in tables 445 and 446, the endpoints of the lines are defined. The contents of
the respective X's are held in the IN_ARRAY parameter and the contents of the respective Y's are held in the
OUT_ARRAY parameter. If a set of points are specified such that a region of the input range is not specified, then the
corresponding OUT_n will be set to the closest endpoint of the input value, either high or low, when the specified
region is exceeded.
Table 445. IN_ARRAY Coordinates
Index
Coordinate
Table 446. OUT_ARRAY Coordinates

Index
Coordinate
X11 - Start value of SP for the OUT_1 line.

(X11 < X12)
Y11 - Value of OUT_1 at X11
X12 - End value of SP for the OUT_1 line.

(X11 < X12)
X21 - Start value of SP for the OUT_2 line.

(X21 < X22)
X22 - End value of SP for the OUT_2 line.

(X21 < X22)
A configuration error is set in BLOCK_ERR and the actual mode of the block goes to Out of Service if the X values have
any of the following conditions: X21 < X11, X12 < = X11, X22 < = X21.
Refer to figure 420 for an example of LOCKVAL = true, and figure 421 for an example of LOCKVAL = false. The
parameter LOCKVAL provides an option to specify whether OUT_1 remains at its ending level when control is switched
164
Instruction Manual
D103412X012
August 2012
to OUT_2, or goes to Y11. If LOCKVAL is true, OUT_1 remains at its ending value when X is greater than X12. If LOCKVAL
is false, then OUT_1 goes to Y11 when X is greater than X12 .
Figure 420. OUT with LOCKVAL True
OUT 2
OUT 1
Figure 421. OUT with LOCKVAL False
OUT 1 remains at
end point when
OUT_2 is nonzero
OUT 1
OUT 2
OUT_1 goes to zero
OUT_2 becomes
0%
50%
SP
0%
100%
50%
SP
100%
Some hysteresis in the switching point may be required because the output may change by a full stroke of the valve.
HYSTVAL [12] contains the amount of hysteresis. If X < = X12-HYSTVAL, OUT_1 may be determined by the calculated
y value. If X12-HYSTVAL < X < X12 and X has not reached X12 since it was less than X12-HYSTVAL, OUT_1 may be
determined by the calculated y value. If X12-HYSTVAL < X < X12 and X has reached X12 since it was less than
X12-HYSTVAL, OUT_1 may be determined by the LOCKVAL setting. If X12 < X, OUT_1 may be determined by the
LOCKVAL setting.
Initialization and Back Calculation Requirements

Refer to figure 422, Output Splitter Configuration, where:
PID1 = Upstream driving controller or function block.
Splitter = Split range function block being described.
AO = Receiver of OUT_1 for 0-50% range of SP
PID2 = Receiver of OUT_2 for 50-100% range of SP
Figure 422. Output Splitter Configuration
BK_CAL_IN
CASIN
PID1
OUT
CASIN
BK_CAL_IN2
Splitter
BK_CAL_IN1
PID2
BK_CAL_OUT
OUT2
BK_CAL_OUT
OUT1
CASIN
AO
BK_CAL_OUT
165
Instruction Manual

August 2012
D103412X012
CAS_IN of the Splitter receives the OUT of PID1. BKCAL_IN of PID1 receives BKCAL_OUT of the Splitter. CAS_IN of the
AO receives OUT_1 of the Splitter and PID2 receives OUT_2 of the Splitter. BKCAL_IN_1 of the Splitter receives
BKCAL_OUT of the AO and BKCAL_IN_2 of the Splitter receives BKCAL_OUT of PID2.
The discussion in this section defines the behavior which is used to handle the initial value calculation and status which
can in turn be sent to PID1. This behavior is defined in such a way that no bumps are generated by changing modes,
and that PID1 does not wind up.
The splitter utilizes special handling for cascade initialization because it has two independent outputs. When a
downstream block indicates to the splitter that it wants to initialize, by asserting IR (initialization request) on its
BKCAL_OUT, one of two things happens. Under some circumstances, it is possible to pass an initialization request from
a downstream block back up to the block upstream of the splitter, so that all three blocks balance for bumpless
transfer to cascade mode. Otherwise, the requested splitter output goes to the requested value by placing an internal
offset between that output and the output of the curve, and then ramping that offset to zero in BAL_TIME seconds
after the cascade is made up.
The splitter normally runs with both outputs connected to blocks in cascade mode. If one or both of the blocks is not in
cascade mode, special limiting action is taken. Specifically, if one block indicates that it is not in cascade by NI (not
invited) status on its BKCAL_OUT, then the BKCAL_OUT of the splitter asserts limits at the range extremes of the block
that is still in cascade mode. Even if the upstream controller does not want to operate in that range, there will be no
reset windup when it can move into the range. If both downstream blocks show NI, then the splitter can only wait until
one of them requests cascade initialization. BKCAL_OUT of the splitter can hold the upstream block at the value of the
SP. The actual mode is IMan.
When cascade initialization is requested, by IR substatus on a BKCAL_IN, it is first necessary to determine if the other
BKCAL_IN has NI substatus. If so, the value at the BKCAL_IN asserting IR is taken as the Y value for its curve, and the
resulting X value is sent on BKCAL_OUT to PID1. If the other substatus is OK, then the internal offset and BAL_TIME is
used. If both blocks have IR substatus, then one output is processed until its cascade is closed. The choice is based on
the presence of limit status in BKCAL_IN. If BKCAL_IN_1 is limited, then if BKCAL_IN_2 is not limited then OUT_2 is
processed first, else OUT_1 is processed first.
Cascade initialization is also required when the block transitions from Auto to Cas mode. This action is identical to that
described for the PID block.
The required actions are summarized in table 447.
Table 447. OUT_ARRAY Coordinates
BKCAL_IN_1
BKCAL_IN_2
BKCAL_OUT
Action
NI
NI
NI
Not Specified
NI
OK
OK
BKCAL_OUT limited to X21 low and X22 high
OK
NI
OK
BKCAL_OUT limited to X11 and X12 high
IR
NI
IR
Initialize cascade to value given by curve X1 vs Y1
IR
OK
OK
Initialize OUT_1 using internal offset from Y1
NI
IR
IR
Initialize cascade to value given by curve X2 vs Y2
OK
IR
OK
Initialize OUT_2 using internal offset from Y2
Note 1: OK means the cascade is closed.

Note 2: Recommend using the average of BKCAL_IN_1 and BKCAL_IN_2, or just SP.
The BKCAL_OUT status shows limited high if an increase in SP cannot be effectively passed on to either output because
the BKCAL_IN_n of both outputs indicates that a move in the needed direction is limited. Similarly, limited low is set if
a decrease in SP cannot be effectively passed on to either output. The slope of the limited line(s) affects the limit
direction. BKCAL_OUT also shows limit status at the X extremes X11 and X22.
Initialization is not automatic under all circumstance because some situations have conflicting needs. In general, when
a control region is in trouble, the upstream controller is limited so it will not drive further into that region. When you
want to move to the other active region, you can put the upstream controller into Man mode and move it, or you can
166
Instruction Manual
D103412X012
August 2012
drop the good downstream block out of Cas mode for one evaluation cycle and then restore Cas mode. This initializes
the upstream controller to the remaining good region of control.
OS Function Block Parameter List (table 448)

Table 448. Output Splitter Function Block Parameter Definitions

Label
PARAMETER_NAME
Index
Number
RO /
RW
Block
Mode
Initial
Value
Description
Static Revision
ST_REV
RO
N/A
0 to 65535

The revision level of the static data associated with the
function block. The revision value will be incremented each
time a static parameter value in the block is changed.
Tag Description
TAG_DESC
RW
ALL
7 bit ASCII
Spaces
Strategy
STRATEGY
RW
ALL
0 to 65535
Data Type: Unsigned 16:

The strategy field can be used to identify grouping of
blocks. This data is not checked or processed by the block.
Alert Key
ALERT_KEY
RW
ALL
1 to 255

The identification number of the plant unit. This information
may be used in the host for sorting alarms, etc.
Block Mode
MODE_BLK
5
7:OOS
3:AUTO
2:CAS
OOS until
block
configured,
then last
valid target
OOS+AUTO+CAS
Range
TARGET
5.1
RW
ACTUAL
5.2
RO
OOS
OOS AUTO
CAS
PERMITTED
5.3
RW
NORMAL
5.4
RW
Block Error
BLOCK_ERR
Setpoint
SP
Output 1
OUT_1
Output 2
OUT_2
Output 1 Range
OUT_1_RANGE
10
RO
RO

The user description of the intended application of the
block.
Data Type: DS69

The actual, target, permitted, and normal modes of the
block.
AUTO+CAS
N/A
1: Block
Configuration Error
7: Input Failure/Bad
PV Status
8: Output Failure
14: Powerup
15: OutofService
Dynamic

0=Inactive
1=Active
This parameter reflects the error status associated with the
hardware or software components associated with a block.
It is a bit string, so that multiple errors may be shown.
PV_SCALE +/- 10%
Data Type: DS65

Analog setpoint of the block
MAN
OOS
OUT_SCALE
+/- 10%
Data Type: DS65

The primary analog output value calculated as a result of
executing the function (the first output value and status).
MAN
OOS
OUT_SCALE
+/- 10%
Data Type: DS65

The primary analog output value calculated as a result of
executing the function (the second output value and
status).
EU at 100%
EU at 0 %
Unit Index
Decimal Point
100
0
%
2
Data Type: DS68

The high and low scale values, engineering units code, and
number of decimal places to be used in displaying the OUT
value, this parameter has no effect on this block.
-Continued-
167
Instruction Manual

August 2012
D103412X012
Table 448. Output Splitter Function Block Parameter Definitions (Continued)

Label
PARAMETER_NAME
Index
Number
RO /
RW
Output 2 Range
OUT_2_RANGE
11
RO
Grant Deny
GRANT_DENY
12
Block
Mode
EU at 100%
EU at 0 %
Unit Index
Decimal Point
GRANT
12.1
N/A
DENY
12.2
N/A
13
OOS
Status Options
STATUS_OPTS
Cascade Input
CAS_IN
Range
14
Initial
Value
Description
100
0
%
2
Data Type: DS68

The high and low scale values, engineering units code, and
number of decimal places to be used in displaying the OUT
value, this parameter has not effect on this block.
0: Program
1: Tune
2: Alarm
3: Local
All bits: 0
Data Type: DS70

Options for controlling access of host computers and local
control panels to operating, tuning, and alarm parameters
of the block. GRANT:0=N/A, 1=granted
DENY: 0=N/A, 1= denied
1: IFS if BAD CAS_IN
All bits: 0
All bits: 0
Status
BAD:
NC:
const
Value

0=Disabled 1=Enabled
User option for status
Data Type: DS65
The remote setpoint from another block.
Data Type: DS65
Output value to another block for backwards output
tracking.

BKCAL_OUT
15
Input Array
IN_ARRAY
16
All: 0
Data Type: Float

Used with OUT_ARRAY to map input to output. See Input to
Output Mapping, page 163.
Output Array
OUT_ARRAY
17
All: 0
Data Type: Float

Used with IN_ARRAY to map input to output. See Input to
Lockval
LOCKVAL
18
Back Calculation Input 1

BKCAL_1_IN
19
Back Calculation Input 2

BKCAL_2_IN
RO
Status Limits
0=Undfined
1=no lock
2=lock
BAD:
NC:
const
Status
20
0=
Undefined
Value
Status
BAD:
NC:
const
Value
Positive
Balance Time
BAL_TIME
21
Hystval
HYSTVAL
22
Update Event
UPDATE_EVT
23
RO
N/A
UNACKNOWLEDGED
23.1
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=
Undefined
UPDATE STATE
23.2
RO
N/A
0=Undefined
1=Update Reported
2=Updated not
reported
0=
Undefined
TIME_STAMP
23.3
RO
N/A
STATIC_REVISION
23.4
RO
N/A
RELATIVE_INDEX
23.5
RO
N/A
0
-Continued-
168
Data Type: Enum

Used with OUT_ARRAY to map input to output. See Input to
Data Type: DS65
The value and status reflecting the BKCAL_OUT of the lower
block associated with OUT_1. It is used for initialization and
to prevent windup in upstream blocks.
Data Type: DS65
The value and status reflecting the BKCAL_OUT of the lower
block associated with OUT_2. It is used for initialization and
to prevent windup in upstream blocks.
Data Type: Float
Specifies the time for the internal working value of bias or
ratio to return to the operator set bias or ratio, in seconds.
Data Type: DS73

This alert is generated by any change to the static data.
Instruction Manual
D103412X012
August 2012
Table 448. Output Splitter Function Block Parameter Definitions (Continued)

Label
PARAMETER_NAME
Index
Number
Block Alarm
BLOCK_ALM
RO /
RW
Block
Mode
RW
N/A
0: Undefined
1: Acknowledged
2: Unacknowledged
0: Undefined
1: Clear reported
2: Clear not reported
3: Active reported
4: Active not
reported
Range
Initial
Value
Description
24
UNACKNOWLEDGED
24.1
ALARM_STATE
24.2
RO
N/A
TIME_STAMP
24.3
RO
N/A
SUBCODE
24.4
RO
N/A
VALUE
24.5
RO
N/A
Data Type: DS72

The block alarm is used for all configuration, hardware,
connection failure, or system problems in the block. The
cause of the alert is entered in the subcode field.
View Lists
Table 449. OS Function Block, View 1
Index Number
Index Number
Parameter
ST_REV
Parameter
ST_REV
5.1
5.1
5.2
5.2
5.3
5.3
5.4
5.4
BLOCK_ERR
BLOCK_ERR
SP
SP
OUT_1
OUT_1
OUT_2
OUT_2
14
CAS_IN
14
CAS_IN
15
BKCAL_OUT
19
BKCAL_1_IN
20
BKCAL_2_IN

Index Number
Parameter
ST_REV
10
OUT_1_RANGE
11
OUT_2_RANGE
12.1
GRANT_DENY.GRANT
12.2
GRANT_DENY.DENY

Index Number
Parameter
ST_REV
STRATEGY
ALERT_KEY
13
STATUS_OPTS
16
IN_ARRAY
17
OUT_ARRAY
18
LOCKVAL
21
BAL_TIME
169

August 2012

OUTPUT SPLITTER FUNCTION BLOCK
All
Characteristics
Static Revision
Tag Description
Strategy
Alert Key
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Block Error
Setpoint: Status
Setpoint: Value
Output 1: Status
Output 1: Value
Output 2: Status
Output 2: Value
Output 1 Range: EU at 100%
Output 1 Range: Units Index
Output 1 Range: Decimal
Output 2 Range: Units Index
Output 2 Range: Decimal
Grant Deny: Grant
Grant Deny: Deny
Status Options
Input Array[1]
Input Array[2]
Input Array[3]
Input Array[4]
Output Array[1]
Output Array[2]
Output Array[3]
Output Array[4]
Lockval
Back Calculation Input 1: Status
Back Calculation Input 1: Value
Back Calculation Input 2: Status
Back Calculation Input 2: Value
Balance Time
Hystval
Block Alarm: Value
170
Instruction Manual
D103412X012
Instruction Manual
Detailed SetupAI Function Block
D103412X012
August 2012
Analog Input Function Block

Overview
The Analog Input (AI) function block (figure 423) processes field device measurements and makes them available to
other function blocks. The output value from the AI block is in engineering units and contains a status indicating the
quality of the measurement. The measuring device may have several measurements or derived values available in
different channels. Use the channel number to define the variable that the AI block processes.
Figure 423. Analog Input (AI) Function Block
OUT
OUT
OUT_D
FIELDBUSFBUS_31A
OUT_D
= THE BLOCK OUTPUT VALUE AND STATUS

= DISCRETE OUTPUT THAT SIGNALS A SELECTED
ALARM CONDITION
The AI block supports alarming, signal scaling, signal filtering, signal status calculation, mode control, and simulation.
In Automatic mode, the block's output parameter (OUT [8]) reflects the process variable (PV [7]) value and status. In
Manual mode, OUT [8] may be set manually. The Manual mode is reflected on the output status. A discrete output
(OUT_D [37]) is provided to indicate whether a selected alarm condition is active. Alarm detection is based on the OUT
[8] value and user specified alarm limits. Figure 424 illustrates the internal components of the AI function block, and
table 457 lists the AI block parameters and their units of measure, descriptions, and index numbers.
Modes
The AI function block supports three modes of operation as defined by the MODE_BLK [5] parameter:
Manual (Man) The block output (OUT [8]) may be set manually.
Automatic (Auto) OUT reflects the analog input measurement or the simulated value when simulation is enabled.
Out of Service (OOS) The block is not processed. FIELD_VAL [19] and PV [7] are not updated and the OUT [8] status
is set to Bad: Out of Service. The BLOCK_ERR [6] parameter shows Out of Service. In this mode, you can make
changes to all configured parameters. The target mode of a block may be restricted to one or more of the
supported modes.
Alarm Detection
A block alarm will be generated whenever the BLOCK_ERR [6] has an error bit set. The types of block errors for the AI
block are defined in table 455.
171
Instruction Manual

August 2012
D103412X012
Figure 424. Analog Input Function Block Schematic

ANALOG
MEASUREMENT
ALARM_TYPE
ACCESS
ANALOG
MEAS.
HI_HI_LIM
HI_LIM
LO_LO_LIM
LO_LIM
CHANNEL
ALARM
DETECTION
OUT_D
ALARM_HYS
LOW_CUT
SIMULATE
L_TYPE
FIELD_VAL
PV
FILTER
PV_FTIME
IO_OPTS
STATUS
CALC.
OUT
MODE
FIELDBUSFBUS_02A
CUTOFF
CONVERT
STATUS_OPTS
OUT_SCALE
XD_SCALE
NOTES:
OUT_D = BLOCK OUTPUT VALUE AND STATUS
OUT_D = DISCRETE OUTPUT THAT SIGNALS A SELECTED ALARM CONDITION.
Process Alarm detection is based on the OUT [8] value. You can configure the alarm limits of the following standard
alarms:
High (HI_LIM [28])
Low (LO_LIM [30])
of the PV [7] span can be set using the ALARM_HYS [24] parameter. The priority of each alarm is set in the following
parameters:
HI_PRI [27]
HI_HI_PRI [25]
LO_PRI [29]
LO_LO_PRI [31]
Table 453. AI Function Block Alarm Priorities
Priority Number
0
The priority of an alarm condition changes to 0 after the condition that caused the alarm is corrected.
An alarm condition with a priority of 1 is recognized by the system, but is not reported to the operator.
3-7
8-15
1. The priority classes advise and critical have no relationship to PlantWeb Alerts.
172
Instruction Manual
D103412X012
August 2012
Table 454. Channel Selections for the Analog Input Function Block
Parameter(1)
Channel
Block
Index Number
XD_SCALE Units
TRAVEL_TARGET
TB
49
% (1342)
TB
17
% (1342)
TRAVEL
TB
34
% (1342)
SUPPLY_PRESS
TB
35
psig (1143), bar (1137), kPa (1133), inHg (1155), inH20 (1146), kg/cm2 (1145)
PRESSURE_A
TB
36
PRESSURE_B
TB
37
PRESSURE_DIFF
TB
38
DRIVE_SIGNAL
TB
53
% (1342)
10
TRAVEL_DEVIATION
TB
52
% (1342)
11
TEMPERATURE
TB
48
C (1001), F (1002)
12
CYCLE_COUNT
TB
73
no units (1588)
13
TRAVEL_ACCUMULATION
TB
72
% (1342)
1. Refer to table 414 for transducer block parameter descriptions and table 425 for AO parameter descriptions.
Status Handling
The AI block only gets Good NonSpecified Unlimited or Bad Device Failure for status from the transducer. This is
reflected in FIELD_VAL.STATUS [19.1]. PV.STATUS [7.1] is the same as FIELD_VAL.STATUS [19.1]. OUT.STATUS [8.1]
can also reflect Bad, Out of Service in addition to PV.STATUS [7.1] values.
In the STATUS_OPTS [14] parameter, you can select from the following options to control the status handling:
Propagate Fail ForwardIf the status from the sensor is Bad, Device failure or Bad, Sensor failure, propogate it to OUT
without generating an alarm. The use of these substatus in OUT is determined by this option. Through this option,
you may determine whether alarming (sending out an alert) will be done by the block or propagated downstream for
alarming.
Figure 425. Analog Input Function Block Timing Diagram
OUT (mode in man)

OUT (mode in auto)
PV
FIELD_VAL
TIME (seconds)
PV_FTIME
FIELDBUSFBUS_03A
63% of Change
Uncertain if in Manual modeThe status of the Output is set to Uncertain when the mode is set to Manual.
Note
1. The instrument must be in Out of Service mode to set the status option.
2. The AI block only supports the Uncertain if in Manual and Propagate failure. Unsupported options are not grayed out; they
appear on the screen in the same manner as supported options.
173
Instruction Manual

August 2012
D103412X012
Filtering
The filtering feature changes the response time of the device to smooth variations in output readings caused by rapid
changes in input. You can adjust the filter time constant (in seconds) using the PV_FTIME [18] parameter. Set the filter
time constant to zero to disable the filter feature.
Signal Conversion
You can set the signal conversion type with the Linearization Type (L_TYPE [16]) parameter. You can view the
converted signal (in percent of XD_SCALE [10]) through the FIELD_VAL [19] parameter.
FIELD_VAL =
100 X (Channel Value) - EU *@0%

(EU *@100% - EU *@0%)
*XD_SCALE values
You can choose from direct, indirect, or indirect square root signal conversion with the L_TYPE [16] parameter.
Direct
Direct signal conversion allows the signal to pass through the accessed channel input value (or the simulated value
when simulation is enabled).
PV = Channel Value
Indirect
Indirect signal conversion converts the signal linearly to the accessed channel input value (or the simulated value when
simulation is enabled) from its specified range (XD_SCALE [10]) to the range and units of the PV [7] and OUT [8]
parameters (OUT_SCALE [11]).
PV =
FIELD_VAL
100
X (EU **@100% - EU **@0%) + EU **@0%
**OUT_SCALE values
Indirect Square Root

Indirect Square Root signal conversion takes the square root of the value computed with the indirect signal conversion
and scales it to the range and units of the PV [7] and OUT [8] parameters.
PV =
FIELD_VAL
100
X (EU **@100% - EU **@0%) + EU **@0%
**OUT_SCALE values
174
Instruction Manual
D103412X012
August 2012
When the converted input value is below the limit specified by the LOW_CUT [17] parameter, a value of zero is used
for the converted value (PV [7]). This option is useful to eliminate false readings when the differential pressure
measurement is close to zero.
Note
Invert is the only I/O option supported by the AI block. You can set the I/O option in Out of Service mode only.
Advanced Features
The AI function block provided with the DVC6200f provides added capability through the addition of the following
parameters:
ALARM_SELAllows one or more of the process alarm conditions detected by the AI function block to be used in
setting its OUT_D [37] parameter.
OUT_DDiscrete output of the AI function block based on the detection of process alarm condition(s). This parameter
may be linked to other function blocks that require a discrete input based on the detected alarm condition.
STDDEV and CAP_STDDEV are diagnostic parameters that can be used to determine the variability of the process.
Simulation
To support testing, you can either change the mode of the block to manual and adjust the output value, or you can
enable simulation through the configuration tool and manually enter a value for the measurement value and its status.
To enable simulation, you must first install the Simulate Enable jumper across the instrument AUX terminals (see page
36). Next you must use the configuration tool to enable the parameter SIMULATE [9].
With simulation enabled, the actual measurement value has no impact on the OUT [8] value or the status.
Block Errors
Table 455 lists conditions reported in the BLOCK_ERR [6] parameter. Conditions in italics are inactive for the AI block
and are given here only for your reference.
Condition Number
Other
Block Configuration Error the selected channel carries a measurement that is incompatible with the engineering units
selected in XD_SCALE, the L_TYPE parameter is not configured, or CHANNEL = zero.
Link Configuration Error
Simulate Active Simulation is enabled and the block is using a simulated value in its execution.
Local Override
Device Fault State
Device Needs Maintenance Soon
Input failure/process variable had Bad status The hardware is bad, or a bad status is being simulated
Output failure
Memory failure
10
Lost Static Data
11
Lost NV Data
12
Readback Check Failed
13
Device Needs Maintenance Now
14
Power Up - This condition exists until the AI function block executes for the first time.
15
Out of Service The actual mode is Out of Service.
175
Instruction Manual

August 2012
D103412X012
Troubleshooting
Refer to table 456 to troubleshoot any problem that you encounter.
Table 456. Troubleshooting
Symptom
Mode will not leave OOS
Possible Causes
Target mode is not set
Configuration error
Corrective Action
Set target mode to something other than OOS
BLOCK_ERR [6] will show the configuration error bit set. The
following are parameters that must be set before the block is
allowed out of OOS:
CHANNEL [15] must be set to a valid value and cannot be
left at initial value of 0.
XD_SCALE [10]. UNITS_INDEX must match the units in the
transducer block channel value.
L_TYPE [16] must be set to Direct, Indirect, or Indirect
Square Root and cannot be left at an initial value of 0.
Resource block
Schedule
Process and/or block alarms will not work
Features
Notification
Status Options
Value of output does not make sense
Linearization Type
Scaling
The actual mode of the Resource block is OOS. See Resource

Block Diagnostics for corrective action.
Block is not scheduled and therefore cannot execute to go to
Target Mode. Schedule the block to execute.
FEATURES_SEL [18] in the resource block does not have Alerts
enabled. Enable the Reports Supported bit.
LIM_NOTIFY [32] in the resource block is not high enough. Set
equal to MAX_NOTIFY [31], also in the resource block.
STATUS_OPTS [14] has Propagate Fault Forward bit set. This
should be cleared to cause an alarm to occur.
L_TYPE [16] must be set to Direct, Indirect, or Indirect Square
Root and cannot be left at an initial value of 0.
Scaling parameters are set incorrectly:
XD_SCALE.EU0 and EU100 should match that of the trans
ducer block channel value.
OUT_SCALE.EU0 and EU100 are not set properly.
Cannot set HI_LIMIT [28], HI_HI_LIMIT [26],

LO_LIMIT [30], or LO_LO_LIMIT [32] VALUES
Scaling
Limit values are outside the OUT_SCALE.EU0 and

OUT_SCALE.EU100 values. Change OUT_SCALE [11] or set
values within range.
AI Function Block Parameter List (table 457)

176
Instruction Manual
D103412X012
August 2012
Table 457. Analog Input Block Parameter Definitions

Label
PARAMETER_NAME
Index
Number
RO /
RW
Write Block
Mode
Range
Initial
Value
Description
N/A
0 to 65535

the block is changed
ALL
7 bit ASCII
spaces

the block.
ALL
0 to 65535

the block.

alarms, etc.
Static Revision
ST_REV
Tag Description
TAG_DESC
Strategy
STRATEGY
Alert Key
ALERT_KEY
Block Mode
MODE_BLK
RO
ALL
1 to 255
OOS
MAN
AUTO
OOS until block

is configured,
then last valid
target
TARGET
5.1
RW
ALL
ACTUAL
5.2
RO
ALL
OOS
OOS, MAN,
AUTO
PERMITTED
5.3
RW
ALL
NORMAL
5.4
RW
ALL
OOS+MAN+AUTO
Data Type: DS69

Valid Bits: 7: OOS, 4: MAN, 3: AUTO
the block.
AUTO
Block Error
BLOCK_ERR
RO
Error
3: Simulate Active
7: Input Failure/ Bad PV
Status
14: Powerup
15: OutofService
Process Value
PV
RO
PV Status set equal to

FIELDV_VAL Status
Data Type: DS65

Reflects the scaled value from the configured
channel. Units set by OUT_SCALE and L_TYPE.
Primary Output
OUT
OUT_STATE
Data Type: DS68

Simulate
SIMULATE
OOS, MAN
SIMULATE_STATUS
9.1
ALL
SIMULATE_VALUE
9.2
ALL
TRANSDUCER_STATUS
9.3
RO
TRANSDUCER_VALUE
9.4
RO
ENABLE/DISABLE
Transducer Scale
XD_SCALE
Output Scale
OUT_SCALE
9.5
10
11
0
0

0=Inactive
1=Active
Error status associated with the hardware or
software for the AI block.
Data Type: DS82

A group of data that contains the current transducer
value and status, the simulated transducer value
and status, and the enable/disable bit.
ALL
0=Not Initialized
1=Simulation Disabled
2=Simulation Active
OOS
EU at 100%
EU at 10%
Units Index
Decimal Point
100
0
%
2
Data Type: DS68

Transducer scaling (XD_SCALE) is applied to the
value from the channel to produce the FIELD_VAL in
percent. The XD_SCALE units code must match the
channel units code (if one exists), or the block will
remain in OOS mode after being configured.
OOS
EU at 100%
EU at 10%
Units Index
Decimal Point
100
0
%
2
Data Type: DS68

code, and number of decimal places to be used in
displaying the OUT parameter and parameters
which have the same scaling as OUT.
1=simulate
disabled
-Continued-
177
Instruction Manual

August 2012
D103412X012
Table 457. Analog Input Block Parameter Definitions (Continued)

Label
PARAMETER_NAME
Grant Deny
GRANT_DENY
Index
Number
RO /
RW
Write Block
Mode
Range
Initial
Value
Description
All bits: 0
Data Type: DS70

Options for controlling access of host computer and
local control panels to operating, tuning, and alarm
parameters of the block.
12
Valid Bits
0: Program
1: Tune
2: Alarm
3: Local
GRANT
12.1
ALL
DENY
12.2
ALL
13
OOS
10: Low cutoff
All bits: 0

0=Disable
1=Enable
User options for Output Control.
All bits: 0

0=Disable
1=Enable
User options for Status
I/O Options
IO_OPTS
Status Options
STATUS_OPTS
14
OOS
forward
6: Uncertain if Limited
7: Bad if Limited
8: Uncertain in Man
Mode
AI Channel
CHANNEL
15
OOS
See table 454
0: Undefined
1: Direct
2: Indirect
3: Ind. Sqr. Root
All bits: 0
0: Undefined

Used to select the type of threshold that is used to
set the output.
0: Undefined
Data Type: Enum

Linearization type. Determines whether the field
value is used directly (Direct), is converted linearly
(Indirect), or is converted with the square root
(Indirect Square Root). The OUT_SCALE is normally
the same as the transducer, but if L_TYPE is set to
Indirect or Ind Sqr Root, OUT_SCALE determines the
conversion from FIELD_VAL to the output.
Linearization Type
L_TYPE
16
OOS, MAN
Low Cutoff
LOW_CUT
17
ALL
Positive
Data Type: Float

If calculated output is below this value the output is
0.

PV_FTIME
18
ALL
Positive
Data Type: Float

Time constant of first order filter on PV, in seconds.
Field Value
FIELD_VAL
19
Data Type: DS65

Value of the field device analog input, with a status
reflecting the Transducer condition.
Updated Event
UPDATE_EVT
20
RO
UNACKNOWLEDGED
20.1
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
UPDATE_STATE
20.2
RO
N/A
0=Undefined
1=Update reported
0=Undefined
TIME_STAMP
20.3
RO
N/A
STATIC_REVISION
20.4
RO
N/A
RELATIVE_INDEX
20.5
RO
N/A
Block Alarm
BLOCK_ALM
UNACKNOWLEDGED
21
21.1
RW
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clearreported
2=Clearnot reported
3=Activereported
4=Activenot reported
ALARM_STATE
21.2
RO
TIME_STAMP
21.3
RO
SUBCODE
21.4
RO
VALUE
21.5
RO
-Continued-
178
Data Type: DS73

This alarm is generated whenever a static parameter
is changed.
Data Type: DS72

hardware, connection failure or system problems in
the block. The cause of the alert is entered in the
subcode field.
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
Alarm Summary
ALARM_SUM
Index
Number
RO /
RW
Write Block
Mode
Range
Initial
Value
22
CURRENT
22.1
RO
ALL
UNACKNOWLEDGED
22.2
RO
ALL
UNREPORTED
22.3
RO
ALL
DISABLED
22.4
RW
ALL
0: Discrete alarm
1: Hi Hi alarm
2: Hi Alarm
3: Lo Lo Alarm
4: Lo Alarm
7: Block alarm
All bits: 0
Description
Data Type: DS74 Current alert status,
unacknowledged states, unreported states, and
disabled states of the alarms associated with the
function block.
0=clear
0=acknowledged
0=reported
0=enabled
Acknowledge Option
ACK_OPTION
23
ALL
0: Discrete alarm
1: Hi Hi alarm
2: Hi Alarm
3: Lo Lo Alarm
4: Lo Alarm
7: Block alarm
Alarm Hysteresis
ALARM_HYS
24
ALL
0 - 50%
0.50%
High High Priority

HI_HI_PRI
25
ALL
0 to 15

The priority of the hi hi alarm.
High High Limit

HI_HI_LIM
26
ALL
OUT_SCALE
Data Type: Float

Value of analog input which will generate an alarm.
High Priority
HI_PRI
27
ALL
0 to 15

The priority of the high alarm.
Hi Limit
HI_LIM
28
ALL
OUT_SCALE
Data Type: Float

Low Priority
LO_PRI
29
ALL
0 to 15

The priority of the low alarm.
Low Limit
LO_LIM
30
ALL
OUT_SCALE
Data Type: Float

Low Low Priority

LO_LO_PRI
31
ALL
0 to 15

The priority of the low low alarm.
Low Low Limit

LO_LO_LIM
32
ALL
OUT_SCALE
Data Type: Float

High High Alarm

HI_HI_ALM
33
All bits: 0
UNACKNOWLEDGED
33.1
RW
ALARM_STATE
33.2
RO
TIME_STAMP
33.3
RO
SUBCODE
33.4
RO
VALUE
33.5
RO
High Alarm
HI_ALM
N/A
Data Type: Float

Hysteresis on alarms.
Data Type: DS71

The status of the hi hi alarm and its associated time
stamp.
34
UNACKNOWLEDGED
34.1
RW
ALARM_STATE
34.2
RO
TIME_STAMP
34.3
RO
SUBCODE
34.4
RO
VALUE
34.5
RO
Low Alarm
LO_ALM

0=Disable
1=Enable
Selection of whether alarms associated with the
block will be automatically acknowledged.
N/A
Data Type: DS71

The status of the hi alarm and its associated time
stamp.
35
UNACKNOWLEDGED
35.1
RW
ALARM_STATE
35.2
RO
TIME_STAMP
35.3
RO
SUBCODE
35.4
RO
VALUE
35.5
RO
N/A
Data Type: DS71

The status of the lo alarm and its associated time
stamp.
0
0
-Continued-
179
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Low Low Alarm
LO_LO_ALM
Index
Number
RO /
RW
Write Block
Mode
Initial
Value
Range
Description
36
UNACKNOWLEDGED
36.1
RW
ALARM_STATE
36.2
RO
TIME_STAMP
36.3
RO
SUBCODE
36.4
RO
VALUE
36.5
RO
N/A
Data Type: DS71

The status of the lo lo alarm and its associated time
stamp.
0
0
Extended Parameter
Data Type: DS66
Discrete Output this is true (1) if any of the alarms
selected in ALM_SEL are active.
Output Discrete
OUT_D
37
OOS, MAN
Alarm Select
ALM_SEL
38
ALL
1: Hi Hi alarm
2: Hi Alarm
3: Lo Lo Alarm
4: Lo Alarm
StdDev
STDDEV
39
RO
N/A
Positive float
Data Type: Float

Standard deviation of the measurement.
Cap StdDev
CAP_STDDEV
40
RO
N/A
Positive float
Data Type: Float

Capability standard deviation, the best deviation
that can be achieved.
OUT_STATE
All bits: 0
Data Type: Bitstring

0=unselected
1=selected
Selected alarms that activate the alarm output.
View Lists
Table 458. AI Function Block, View 1
Index Number
Index Number
180
Parameter
Parameter
ST_REV
ST_REV
5.1
10
XD_SCALE
5.2
11
OUT_SCALE
5.3
12.1
GRANT_DENY.GRANT
5.4
12.2
GRANT_DENY.DENY
BLOCK_ERR
PV
OUT
19
FIELD_VAL
22.1
ALARM_SUM.CURRENT
22.2
22.3
22.4
ALARM_SUM.DISABLED
Instruction Manual
D103412X012
August 2012
Index Number
Index Number
Parameter
Parameter
ST_REV
ST_REV
5.1
STRATEGY
5.2
ALERT_KEY
5.3
13
IO_OPTS
5.4
14
STATUS_OPTS
BLOCK_ERR
15
CHANNEL
PV
16
L_TYPE
OUT
17
LOW_CUT
19
FIELD_VAL
18
PV_FTIME
22.1
ALARM_SUM.CURRENT
23
ACK_OPTION
22.2
24
ALARM_HYS
22.3
25
HI_HI_PRI
22.4
ALARM_SUM.DISABLED
26
HI_HI_LIM
37
OUT_D
27
HI_PRI
38
ALM_SEL
28
HI_LIM
39
STDDEV
29
LO_PRI
40
CAP_STDDEV
30
LO_LIM
31
LO_LO_PRI
32
LO_LO_LIM
181
Instruction Manual

August 2012
D103412X012

ANALOG INPUT FUNCTION BLOCK
Quick Config
AI Channel
Linearization Type
Common Config
Acknowledge Option
Alarm Hysteresis
Alert Key
High High Limit
High High Priority
High Limit
High Priority
I/O Options
Linearization Type
Low Low Limit
Low Low Priority
Low Limit
Low Priority
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Advanced Config
Low Cutoff
Static Revision
Status Options
Strategy
I/O Reference
AI Channel
Connectors
Output: Status
Output: Value
182
Online
Block Error
Field Value: Status
Field Value: Value
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Output: Status
Output: Value
Status
Block Error
Other
Tag Description
Grant Deny: Grant
Grant Deny: Deny
Block Alarm: Value
High Alarm: Subcode
Low Alarm: Subcode
Alarm output: Status
Alarm output: Value
Alarm Select
StdDev
Cap StdDev
All
Characteristics
Static Revision
Tag Description
Strategy
Alert Key
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Block Error
Output: Status
Output: Value
Grant Deny: Grant
Grant Deny: Deny
I/O Options
Status Options
AI Channel
Linearization Type
Low Cutoff
Process Value Filter TIme
Field Value: Status
Field Value: Value
Block Alarm: Value
Acknowledge Option
All (continued)
Alarm Hysteresis
High High Priority
High High Limit
High Priority
High Limit
Low Priority
Low Limit
Low Low Priority
Low Low Limit
High Alarm: Subcode
Low Alarm: Subcode
Alarm output: Status
Alarm output: Value
Alarm select
StdDev
Cap StdDev
Instruction Manual
Detailed SetupMAI Function Block
D103412X012
August 2012
Multiple Analog Input Function Block

Overview
The Multiple Analog Input (MAI) function block (figure 426) has the ability to process up to eight field device
measurements and make them available to other function blocks. The output values from the MAI block are in
engineering units and contain a status indicating the quality of the measurement. The measuring device may have
several measurements or derived values available in different channels. Use the channel numbers to define the
variables that the MAI block processes.
Figure 426. Multiple Analog Input (MAI) Function Block
OUT_1
MAI
OUT_2
OUT_3
OUT_5
OUT_6
OUT_7
FIELDBUSFBUS_31A
OUT_4
OUT_8
Out1 = The block output value and

status for the first channel
The MAI block supports mode control. In Automatic mode, the block's output parameters (OUT_1 to OUT_8 [8
through 15]) reflects the process variable (PV) values and status. In Manual mode, OUT may be set manually. The
Manual mode is reflected in the output status. Table 464 lists the MAI block parameters, and their units of measure,
description and index numbers.
Modes
The MAI Function Block supports three modes of operation as defined by the MODE_BLK [5] parameter:
Manual (Man)The block output (OUT_1 to OUT_8 [8 through 15]) may be set manually.
Automatic (Auto)OUT_1 to OUT_8 [8 through 15] reflects the analog input measurement or the simulated value
when the simulation is enabled.
Out of Service (OOS)The block is not processed. PV is not updated and the OUT status is set to Bad: Out of Service.
The BLOCK_ERR [6] parameter shows Out of Service. In this mode, you can make changes to all configurable
parameters. The target mode of a block may be restricted to one or more of the supported modes.
Status Handling
In Man mode, the OUT status constant limit is set to indicate that the value is a constant and the OUT status is Good.
183
Instruction Manual

August 2012
D103412X012
OUT_X status will be Bad if the transducer detects a problem with sensor associated with the channel.
The intended use is for applications where it is necessary to convey DVC6200f measurements from a function.
The configuration of the MAI function block and its associated output channels depends on the specific application.
CHANNEL [7]: Channel must always be set to 21.
The output parameters (OUT_1 to OUT_8 [8 through 15]) are set through the transducer block Instrument menu.
Each output has a channel assigned to it in MAI Channel Map (TB.MAI_CHANNEL_MAP [95]) in the transducer block.
For additional information, refer to table 464.
Block Errors
Table 462 lists conditions reported in the BLOCK_ERR [6] parameter. Conditions in italics are inactive for the MAI block
and are given here only for your reference.
Condition Number
Other
Block Configuration Error: the selected channel carries a measurement that is incompatible with the engineering units selected
in XD_SCALE, the L_TYPE parameter is not configured, or WRITE_CHECK = 0.
Link Configuration Error
Simulate Active
Local Override
Device Fault State
Input failure/process variable had Bad status The hardware is bad, or a bad status is being simulated
Output failure
Memory failure
10
Lost Static Data
11
Lost NV Data
12
Readback Check Failed
13
14
Power Up - This condition exists after power up until the MAI function executes for the first time.
15
Out of Service The actual mode is Out of Service.
Troubleshooting
Refer to table 463 to troubleshoot any problem that you encounter.
Table 463. Troubleshooting
Symptom
Mode will not leave OOS
Possible Causes
Target mode is not set
Resource block
Schedule
Block alarms will not work
Features
Notification
184
Corrective Action
Set target mode to something other than OOS
The actual mode of the Resource block is OOS. See
Resource Block Diagnostics for corrective action.
Block is not scheduled and therefore cannot execute to go
to Target Mode. Typically, BLOCK_ERR [6] will show
PowerUp for all blocks that are not scheduled.
Schedule the block to execute.
FEATURES_SEL [18] in the resource block does not have
Alerts enabled. Enable the Alerts bit.
LIM_NOTIFY [32] in the resource block is not high
enough. Set equal to MAX_NOTIFY [31], also in the
resource block.
Instruction Manual
D103412X012
August 2012
MAI Function Block Parameter List (table 464)

Table 464. MAI Function Block Parameter Definitions
Label
Parameter Name
Index
Number
Static Revision
ST_REV
Tag Description
TAG_DESC
RO /
RW
RO
Mode
N/A
Range
Initial Value
Description
The revision level of the static data
associated with the input selector block.
The revision value will be incremented
each time a static parameter value in the
block is changed.
0 to 65535
7 bit ASCII
spaces
Strategy
STRATEGY
0 to 65535

The strategy field can be used to identify
grouping of blocks. This data is not
checked or processed by the block.
Alert Key
ALERT_KEY
1 to 255

The identification number of the plant
unit. This information may be used in the
host for sorting alarms, etc.
Block Mode
MODE_BLK
TARGET
5.1
RW
ALL
ACTUAL
5.2
RO
ALL
PERMITTED
5.3
RW
NORMAL
5.4
RW
Block Error
BLOCK_ERR
RO
OOS, MAN, AUTO
OOS
ALL
OOS+MAN+AUTO
OOS, MAN, AUTO
ALL
AUTO
OOS
AUTO
Error
7: Input Failure/ Bad PV
Status
14: Powerup
15: OutofService

The user description of the intended
application of the block.
Data Type: DS69

modes of the block.
0 = Inactive
1 = Active
This parameter reflects the error status
associated with the hardware or software
components associated with a block. It is a
bit string, so that multiple errors may be
shown.
This variable must be set to 21. Channel
assignments to the 8 outputs is done
through MAI_CHANNEL_MAP parameter
in transducer block.
MAI Channel
CHANNEL
21 only
0 = undefined
1=FINAL_VALUE
2=TRAVEL_TARGET
3=FINAL_POSITION_VALUE
4=TRAVEL
5=SUPPLY_PRESS
6=ACT_PRESS_A
7=ACT_PRESS_B
8=ACT_PRESS_DIFF
9=DRIVE_SIGNAL
10=TRAVEL_DEVIATION
11=TEMPERATURE
12=CYCLE_COUNT
13=TRAVEL_ACCUM
-Continued-
185
Instruction Manual

August 2012
D103412X012
Table 464. MAI Function Block Parameter Definitions (Continued)

Label
Parameter Name
Index
Number
RO /
RW
Mode
Range
Initial Value
Description
Output 1
OUT_1
OOS
MAN
Channel assigned by
TB.MAI_CHANNEL_MAP
TB.FINAL_VALUE
Data Type: DS65

Output 2
OUT_2
OOS
MAN
Channel assigned by
TB.MAI_CHANNEL_MAP
TB.TRAVEL_TARGET
Data Type: DS65

Output 3
OUT_3
10
OOS
MAN
Channel assigned by
TB.MAI_CHANNEL_MAP
TB.FINAL_POSITION_VA
LUE
Data Type: DS65

Output 4
OUT_4
11
OOS
MAN
Channel assigned by
TB.MAI_CHANNEL_MAP
TB.TRAVEL
Data Type: DS65

Output 5
OUT_5
12
OOS
MAN
Channel assigned by
TB.MAI_CHANNEL_MAP
TB.SUPPLY_PRESS
Data Type: DS65

Output 6
OUT_6
13
OOS
MAN
Channel assigned by
TB.MAI_CHANNEL_MAP
TB.ACT_PRESS_A
Data Type: DS65

Output 7
OUT_7
14
OOS
MAN
Channel assigned by
TB.MAI_CHANNEL_MAP
TB.ACT_PRESS_B
Data Type: DS65

Output 8
OUT_8
15
OOS
MAN
Channel assigned by
TB.MAI_CHANNEL_MAP
TB.ACT_PRESS_DIFF
Data Type: DS65

Update Event
UPDATE_EVT
16
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
0=Undefined
1=Update reported
2=Updated not reported
0=Undefined
UNACKNOWLEDGED
RW
UPDATE_STATE
16.2
RO
N/A
TIME_STAMP
16.3
RO
N/A
STATIC_REVISION
16.4
RO
N/A
RELATIVE_INDEX
16.5
RO
N/A
Block Alarm
BLOCK_ALM
UNACKNOWLEDGED
186
16.1
Data Type: DS73

This alarm is generated whenever a static
parameter is changed.
17
17.1
RW
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clear reported
3=Active reported
ALARM_STATE
17.2
RO
TIME_STAMP
17.3
RO
SUBCODE
17.4
RO
VALUE
17.5
RO
Data Type: DS72

The block alarm is used for all
configuration , hardware, connection
failure or system problems in the block.
The cause of the alert is entered in the
subcode field.
Instruction Manual
D103412X012
August 2012
View Lists
Table 465. MAI Function Block, View 1
Index Number
Index Number
Parameter
ST_REV
Parameter
ST_REV
5.1
5.1
5.2
5.2
5.3
5.3
5.4
5.4
BLOCK_ERR
BLOCK_ERR
OUT_1
OUT_1
OUT_2
OUT_2
10
OUT_3
10
OUT_3
11
OUT_4
11
OUT_4
12
OUT_5
12
OUT_5
13
OUT_6
13
OUT_6
14
OUT_7
14
OUT_7
15
OUT_8
15
OUT_8

Index Number
1
Parameter
ST_REV

Index Number
Parameter
ST_REV
STRATEGY
ALERT_KEY
CHANNEL
187
Instruction Manual

August 2012
D103412X012

MULTIPLE ANALOG INPUT FUNCTION BLOCK
Quick Config
MAI Channel
Common Config
Alert Key
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Advanced Config
Static Revision
Strategy
I/O Reference
MAI Channel
Connectors
Output 1: Status
Output 1: Value
Output 2: Status
Output 2: Value
Output 3: Status
Output 3: Value
Output 4: Status
Output 4: Value
Output 5: Status
Output 5: Value
Output 6: Status
Output 6: Value
Output 7: Status
Output 7: Value
Output 8: Status
Output 8: Value
188
Online
Block Error
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Output 1: Status
Output 1: Value
Output 2: Status
Output 2: Value
Output 3: Status
Output 3: Value
Output 4: Status
Output 4: Value
Output 5: Status
Output 5: Value
Output 6: Status
Output 6: Value
Output 7: Status
Output 7: Value
Output 8: Status
Output 8: Value
Status
Block Error
Other
Tag Description
Block Alarm: Value
All
Characteristics
Static Revision
Tag Description
Strategy
Alert Key
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Block Error
MAI Channel
Output 1: Status
Output 1: Value
Output 2: Status
Output 2: Value
Output 3: Status
Output 3: Value
Output 4: Status
Output 4: Value
Output 5: Status
Output 5: Value
Output 6: Status
Output 6: Value
Output 7: Status
Output 7: Value
Output 8: Status
Output 8: Value
Block Alarm: Value
Instruction Manual
Detailed SetupDO Function Block
D103412X012
August 2012
Discrete Output Function Block

Overview
The Discrete Output (DO) function block (figure 427) processes a discrete set point and outputs it to the specified I/O
channel to produce an output signal. The DVC6200f digital valve controller discrete output block provides both
normal open/closed control and the ability to position the valve in 5% increments for coarse throttling applications.
The digital valve controller measures and uses actual valve position for READBACK_D [16].
Figure 427. Discrete Output (DO) Function Block
BKCAL_OUT_D
CAS_IN_D
DO
OUT_D
READBACK_D
CASIND= The remote set point value from another function block.
BKCALOUTD = The value and status required by the
BKCALIND input of another block for output tracking.
OUT_D = The block output and status.
READBACK_D = Actual valve position
The DO block supports mode control and simulation. In operation, the DO function block determines its set point and
sets the output. The transducer block provides a readback signal of actual position from the instrument. Figure 427
illustrates the primary inputs and outputs of the DO function block, figure 428 illustrates the internal components of
the DO function block. Table 472 lists definitions for the function block parameters.
189
Instruction Manual

August 2012
D103412X012
Figure 428. Discrete Output Function Block Schematic
RCAS_OUT_D
RCAS_IN_D
BKCAL_OUT_D
PV_D
SP_D
CONVERT AND
STATUS
CALCULATION
CAS_IN_D
IO_OPTS
OUT_D
READBACK_D
MODE
SIMULATE_D
SHED MODE
CHANNEL
TRANSDUCER
BLOCK FEEDBACK
TRANSDUCER
BLOCK
When setting up the DO block, CHANNEL [18] must be set to 22, and SHED_OPT [23] must be nonzero.
Note
Actual Block Mode (MODE_BLK.ACTUAL [5.2]) will remain out of service and the block cannot be scheduled if the block has not
been licensed. Contact your Emerson Process Management sales office to upgrade product licensing.
Note
Actual Block Mode (MODE_BLK.ACTUAL [5.2]) will remain in IMAN and the block Readback status will be Bad - Not Connected if
the Output Block Selection is set incorrectly. From the transducer block method Outblock Selection, select the desired output
block, see page 69.
Modes
The DO block supports the following modes:
Manual (Man)The block output OUT_D [9] value may be entered manually.
Automatic (Auto)The block algorithm uses the local set point SP_D [8]value to determine OUT_D [9].
190
Instruction Manual
D103412X012
August 2012
Cascade (Cas)The block uses a set point supplied by another function block.
Note
The transducer block must be in Auto for the mode to go to AUTO, CAS or MAN.
RemoteCascade (RCas)The block uses a set point supplied by a host computer.

Out of Service (OOS)The block is not processed and the output is not transferred to I/O. The BLOCK_ERR [6]
attribute shows Out of service.
Mode Handling
Shed Options RCAS Mode Only
Shed from or climb to a remote mode is determined by the parameter SHED_OPT [23]. A block climbs and sheds
through the same path. For example, if SHED_OPT [23] specifies that a block should shed to Auto, then, if the block
target mode is set to RCas, the block goes through Auto on the way to RCas. You can configure the shed option as
follows:

Remote cascade connection failure shifts actual mode but keeps trying to restore remote cascade (in other words, the
remote cascade target mode stays in effect).
NormalOn failure of a remote cascade connection, the block attempts to attain the highest permitted nonremote
mode until remote cascade is restored. Cas is the highest permitted nonremote mode and Auto is is the next
Retained TargetThe retained target mode is the target mode for the block before changing the target mode to a
remote mode. On failure of a remote cascade connection, the block attempts to attain the retained target mode.
AutoOn failure of a remote cascade connection, the block attempts to attain Auto, if permitted, until remote
cascade is restored.
ManOn failure of a remote cascade connection, the block sheds to Man until a remote cascade connection is
restored.

attempt to restore the connection following failure. The behavior on change to the remote cascade target mode is
identical to that for Shed With Return Options.
NormalOn failure of a remote cascade connection, the block sets the target mode to the highest permitted
nonremote mode. Cas is the highest permitted nonremote mode and Auto is is the next highest permitted
nonremote mode. If Cas or Auto are not available, the block will shed by default to Man.
Retained TargetThe retained target mode is the target mode for the block before changing the target mode to a
remote mode. On failure of a remote cascade connection, the block sets the target mode to the retained target mode.
191
Instruction Manual

August 2012
D103412X012
AutoOn failure of a remote cascade connection, the block sets the target mode to Auto, if permitted.
ManOn failure of remote cascade connection, the block sets the target mode to Man, if permitted.
The user may configure SHED_OPT [23] so that it calls for a target mode that is not permitted. When doing this, the
Block Initialization
The Fieldbus Foundation specification requires that certain parameters have initial values of uninitialized in function
blocks. In addition to setting the Resource block mode to AUTO, the control system or the user must change those
parameters from their uninitialized value to a valid value in order for the function block to move from the Out of
Service mode. For the DO function block, the parameters that must be initialized are:
SHED_OPT [23] (see page 191 for valid values)
CHANNEL [18]
Status Handling
Under normal operating conditions, the status of OUT_D [9] is Good NonCascade, and the status of BKCAL_OUT_D
[21] is Good:Cascade. If the output hardware fails, the status of BKCAL_OUT_D [21] is set to Bad:Device Fail, and the
BLOCK_ERR [6] shows Output Failure. If the hardware used for output feedback fails, the status of READBACK_D [16]
and PV_D [7] is set to Bad:DeviceFail, and the BLOCK_ERR [6] shows Process Variable has Bad Status. If the transducer
block mode is Out of Service, the status of READBACK_D [16] and PV_D [7] is set to Bad:Out of Service.
I/O Selection
To select the I/O associated with the discrete output, configure the value of the CHANNEL [18] parameter. Table 469
lists the valid Channel selections for the DO block.
Table 469. Channel Selections for the Discrete Output Function Block
Selection
Transducer Block Parameter
Transducer block Index
Description
22
SETPOINT_D
32
Discrete Valve Control
Uninitialized
Setting the Output

To set the output for the DO block, you must first set the mode to define the manner in which the block determines its
set point and output. In Cascade mode, the set point equals the input value at the CAS_IN_D [17] parameter. In
Automatic or Manual mode, the set point must be entered manually by the user. For Automatic, the value must be
written to the SP_D [8] parameter and for Manual, the value must be written to OUT_D [9]. In Remote Cascade mode,
the set point is determined by a host computer that is writing to the RCAS_IN_D [22] parameter. Table 470 lists
discrete states used by the digital valve controller for the set point.
192
Instruction Manual
D103412X012
August 2012
Table 470. Valve Set Point for Discrete State

Discrete State
Valve Set Point with IO_OPTS Invert = 0
Closed
Valve Set Point with IO_OPTS Invert = 1

Open
Open
Closed
5%
Closed
10
10%
Closed
15
15%
Closed
20
20%
Closed
25
25%
Closed
30
30%
Closed
35
35%
Closed
40
40%
Closed
45
45%
Closed
50
50%
Closed
55
55%
Closed
60
60%
Closed
65
65%
Closed
70
70%
Closed
75
75%
Closed
80
80%
Closed
85
85%
Closed
90
90%
Closed
95
95%
Closed
100
Open
Closed
To further customize the output, configure the following supported I/O options: SP tracks PV in Man,
SP tracks PV in LO, SP Track retained target in Man or LO, Fault State to Value, Use Fault State value on restart, Target
to Man if Fault State activated, and US PV for BKCAL_OUT.
Note
You can configure the supported I/O options in Out of Service mode only.
The SP_PV Track in Man option permits the set point to track the process variable when the block is in Manual mode.
With this option enabled, the set point (SP_D [8]) becomes a copy of the process variable
(PV_D [7]), and a manuallyentered SP_D [8] value is overwritten on the block's next execution cycle. This option can
prevent a state change when transitioning from Manual to Automatic mode. You can disable this option in Manual or
Out of Service mode only.
The Invert option inverts the set point at SP_D [8] before it is stored in OUT_D [9]. With this option enabled, OUT_D
[9] becomes an inverted copy of SP_D [8] where nonzero values of SP_D [8] are considered a logic 1. With this option
disabled, OUT_D [9] is a direct copy of SP_D [8]. The readback value is processed through the Invert option to become
PV_D [7]. The Use PV for BKCAL_OUT option specifies that BKCAL _OUT equal the value of the process variable (PV_D
[7]) instead of the set point (SP_D [8]). If you do not enable this option, BKCAL_OUT will equal SP_D [8].
Output Block PV Status

The Output Block PV Status is determined by the value of the PlantWeb Alerts Set PV Status parameter in the
transducer block (PWA_SET_STATUS [97]), the Transducer Block mode, and enabled Active PlantWeb alarms. Refer to
table 411.
193
Instruction Manual

August 2012
D103412X012
Block Errors
Table 471 lists conditions reported in the BLOCK_ERR [6] parameter. Conditions in italics are not applicable for the DO
Condition Number
Other (N/A)
Block Configuration Error SHED_OPT or CHANNEL set to 0 (uninitialized)
Simulate active Simulation is enabled and the block is using a simulated value in its execution.
Local Override Device in fault state. Actual mode LO.
Device Fault State Set DO block in fault state after FSTATE_TIME because of Bad status or IFS substatus on CAS_IN_D or Resource
block commanded fault state.
Device Needs Maintenance Soon Indicates a Maintenance PlantWeb Alert condition is active if Block Error Reporting is enabled. See
page 86.
Input failure/process variable has Bad status PV has bad status and Feature Select in the Resource block has the Out Readback bit set
or the transducer block mode is Out of Service.
Output failure PV has bad status or the transducer block mode is Out of Service.
10
11
Lost NV Data (N/A)
12
13
Device Needs Maintenance Now Indicates Failed PlantWeb Alert condition is active if Block Error Reporting is enabled. See page 86.
14
Power Up This condition exists after power up until actual mode is not Out of Service.
15
Out of Service The block is in Out of Service (OOS) mode.
Action on Fault Detection

Fault State is caused by one of three sources: A status pertaining to CAS, A status pertaining to RCAS, or SET_FSTATE
[29] in the resource block. To implement Fault State, configure the following parameters:
IO_OPTS [14]: Determines the action OUT_D [9] will take upon a fault state. If the IO_OPTS [14] Fault State to Value
is not selected, then OUT_D [9] holds its last position when Fault State is set. If Fault State to Value is selected,
OUT_D [9] goes to the FSTATE_VAL_D [20] value when Fault State is set.
FSTATE_TIME [19]: The length of time, in seconds, that the DO block will wait to set Fault State. When
Fault State is set, the OUT_D [9] value goes to either the FSTATE_VAL_D [20] value or holds its last position, depending
on I/O_OPTS [14]. When the block has a target mode of CAS, a fault condition will be detected if the CAS_IN_D [17]
has a BAD status or an Initiate Fault State substatus is received from the upstream block.
FSTATE_VAL_D [20]: Determines the OUT_D [9] value if IO_OPTS [14] Fault State to Value is selected. The OUT_D
[9] value transitions to FSTATE_VAL_D [20] after FSTATE_TIME [19] elapses and the fault condition has not cleared.
Simulation
To support testing of the control strategy, you can enable the SIMULATE_D [17] parameter. Normally, the valve
position value and status used for READBACK_D [16] in the DO block reflect actual process values to the nearest 5%, as
provided by the transducer block. When the SIMULATE_D [17] parameter is enabled, value and status used for
READBACK_D [16] is supplied by the user manually. To enable simulation in the DO function block, the simulate
jumper must be installed. Refer to page 36 of the Installation section for information on the installation of this jumper.
194
Instruction Manual
D103412X012
August 2012
Note
When simulate is active, the output block no longer writes values to the transducer block. If the Output Blk Timeout period is
exceeded, the transducer block may move the valve to the Zero Power Condition depending on the configuration of the Output
Block Timeout Alert.
The SIMULATE_D [10] parameter has three components:

Simulate Enable_Disable determines whether the function block will use the actual valve position value and status,
or Simulate Value and Simulate Status.
Transducer Value and Status reflect the process values provided by the transducer block.
Simulate Value and Status may be entered by the user when Simulate Enable_Disable is set to Enabled.
To use simulate, first install the simulate jumper in the terminal box, then set Simulate Enable_Disable to Enabled,
then enter the desired values for Simulate Value and Status.
When SIMULATE_D [10] is Enabled, the Simulate Active bit of the BLOCK_ERR [6] parameter is set (refer to the Block
Errors description). When the simulate jumper is installed, the Simulate Jumper bit of the transducer block parameter
SELFTEST_STATUS [78] is set.
DO Function Block Parameter List (table 472)

Table 472. Discrete Output Function Block Parameter Definitions
Label
PARAMETER_NAME
Index
Number
RO /
RW
Mode
Range
Initial Value
Description
Static Revision
ST_REV
RO
N/A
0 to 65535

Tag Description
TAG_DESC
RW
ALL
7 bit ASCII
Spaces

the block.
Strategy
STRATEGY
RW
ALL
0 to 65535

the block.
Alert Key
ALERT_KEY
RW
ALL
1 to 255

alarms, etc.
-Continued-
195
Instruction Manual

August 2012
D103412X012
Table 472. Discrete Output Function Block Parameter Definitions (Continued)

Label
PARAMETER_NAME
Block Mode
MODE_BLK
Index
Number
RO /
RW
Mode
Range
Initial Value
Description
OOS
MAN
AUTO
AUTOCAS, AUTORCAS
OOS until
block is
configured,
then last valid
target
OOS+MAN+AUTO+
CAS+RCAS
Data Type: DS69

Valid Bits: 7: OOS, 5: LO, 4: MAN, 3: AUTO
2: CAS, 1: RCAS
the block.
TARGET
5.1
RW
ALL
ACTUAL
5.2
RO
ALL
OOS
OOS+MAN+A
UTO+CAS
+RCAS
PERMITTED
5.3
RW
ALL
NORMAL
5.4
RW
ALL
AUTO+CAS
Block Error
BLOCK_ERR
RO
N/A
Error
3: Simulate Active
4: Local Override
5: Device Fault State Set
7: Input Failure / Bad PV
Status
8: Output Failure
14: Powerup
15: OutofService
Process Value Discrete

PV_D
RO
N/A
PV_D Status set equal

to Readback_D Status
Setpoint Discrete
SP_D
OOS
MAN
AUTO
PV_STATE
Data Type: DS66

The discrete target block output value (set point).
Output Discrete
OUT_D
MAN
OUT_STATE
Data Type: DS66

Position target of valve. 0=closed, 1=open, 2-100
position the value in 5% steps.
Simulate Discrete
SIMULATE_D
10
Dynamic

0=Inactive
1=Active
associated with a block. It is a bit string, so that
multiple errors may be shown.
Dynamic
Data Type: DS66

The discrete process variable calculated from
READBACK_D.
SIMULATE_STATUS
10.1
ALL
SIMULATE_VALUE
10.2
ALL
TRANSDUCER_STATUS
10.3
RO
TRANSDUCER_VALUE
10.4
RO
ENABLE/DISABLE
0
0
0=Not initialized
2=Simulation Active
Data Type: DS83

Allows the transducer discrete input or output to
the block to be manually supplied when simulate is
enabled. When simulation is disabled, the simulate
value and status track the actual value and status.
10.5
ALL
Process Value State

PV_STATE
11
ALL
Data Type: Uint16

Index to the text describing the states of a discrete
output.
Transducer State
XD_STATE
12
ALL
Data Type: Uint16

Index to the text describing the states of a discrete
for the value obtained from the transducer.
Grant Deny
GRANT_DENY
13
All bits: 0
Data Type: DS70

alarm parameters of the block.
GRANT:0=N/A, 1=granted
GRANT
13.1
N/A
DENY
13.2
N/A
0: Program
1: Tune
2: Alarm
3: Local
-Continued-
196
All bits: 0
Instruction Manual
D103412X012
August 2012

Label
PARAMETER_NAME
I/O Options
IO_OPTS
Index
Number
RO /
RW
14
Status Options
STATUS_OPTS
15
Readback Discrete
READBACK_D
16
Cascade Input Discrete

CAS_IN_D
17
Mode
Range
OOS
Valid Bits
0: Invert
1: SP tracks PV in Man
3: SP tracks PV in LO
4: SP Track retained
target in Man or LO
6: Fault State to value
0: freeze
1: go to Fault State
value
7: Use Fault State value
on restart
8: Target to Man if Fault
State activated
9: Use PV for
BKCAL_OUT
0: SP
1: PV
OOS
RO
Backward
N/A
ALL
All bits: 0

0=Disable
1=Enable
Options the user may select for the block processing
of status.
Dynamic
Data Type: DS66

0=closed, 1=open, 5, 10, 15, 30...etc. are position in
5% increments.
Value
OOS
0=undefined
22=Setpoint (D)
Fault State Time

FSTATE_TIME
19
ALL
Positive
Fault State Value Discrete

FSTATE_VAL_D
20
Back Calculation Output Discrete

BKCAL_OUT_D
21
22
All bits: 0

0=Disable
1=Enable
Allows you to select the type of tracking and the
output value when a fault condition occurs.
Supported I/O options for the DO function block are
SP Tracks PV in Man, SP Tracks PV in LO, SP Tracks
Retained Target in Man or LO, Fault State to Value,
Use Fault state on Restart, Target to Man if Fault
State Activated, and Use PV for BKCAL_OUT.
BAD:
NC:
const
18
Remote Cascade Input Discrete

RCAS_IN_D
Description
Status
DO Channel
CHANNEL
RO
Initial Value
22=
Setpoint (D)
Data Type: DS66

The remote set point value from another block.
Defines which transducer parameter receives the
DO output. Select Setpoint (D) to control valve
position.
Data Type: Float

Time from detection of a fault in the remote set
point to the Fault State output action.
ALL

Preset discrete SP_D value to use if I/O_OPTS Fault
State to Value is set.
N/A
Dynamic
Data Type: DS66

The value and status required by the BKCAL_IN_D
input of another block for output tracking
ALL
BAD:
NoCom:
NoVal:
const
Status
Value
Date Type: DS66

Target set point and status provided by a
supervisory host to a discrete control or output
block.
-Continued-
197
Instruction Manual

August 2012
D103412X012

Label
PARAMETER_NAME
Shed Options
SHED_OPT
Index
Number
RO /
RW
23
Remote Cascade Output Discrete

RCAS_OUT_D
24
Update Event
UPDATE_EVT
25
Mode
Range
ALL
0=Uninitialized
1=Normal Shed, Normal
Return
2=Normal Shed, No
Return
3=Shed to Auto, normal
return
4=Shed to Auto, no
return. Target mode
changes to Auto on
detection of a shed
condition
5=Shed to Manual,
normal return
return. Target mode
changes to MAN on
detection of a shed
condition.
7=Shed to retained
target, normal return
8=Shed to retained
target, no return.
(Change target to
retained target)
RO
N/A
Initial Value
Description

Defines action to be taken on remote control device
timeout.
Normal Return - actual mode changes to the next
lowest priority nonremote mode permitted but
returns to the target remote mode when the
remote computer completes the initialization
handshake.
No Return - Target mode changes to the next lowest
priority nonremote mode permitted. The target
remote mode is lost, so no return occurs.
Dynamic
Data Type: DS66

Block set point and status after ramping, provided
to a supervisory host for back calculation and to
allow action to be taken under limiting conditions or
mode change.
UNACKNOWLEDGED
25.1
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
UPDATE_STATE
25.2
RO
N/A
0=Undefined
1=Update reported
0=Undefined
TIME_STAMP
25.3
RO
N/A
STATIC_REVISION
25.4
RO
N/A
RELATIVE_INDEX
25.5
RO
N/A
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clear reported
3=Active reported
Block Alarm
BLOCK_ALM
UNACKNOWLEDGED
Data Type: DS73

This alert is generated by any change to the static
data.
26
26.1
ALARM_STATE
26.2
RO
N/A
TIME_STAMP
26.3
RO
N/A
SUBCODE
26.4
RO
N/A
VALUE
26.5
RO
N/A
Data Type: DS72

hardware, connection failure, or system problems in
the block. The cause of the alert is entered in the
subcode field. The first alert to become active will
set the active status in the status parameter. As
soon as the Unreported status is cleared by the alert
reporting procedure, and other block alert may be
reported without clearing the Active status, if the
subcode has changed.
Extended Blocks
Setpoint Rate Up
SP_RATE_UP
27
>= 0
Data Type: Float

The ramp rate for SP up in AUTO, CAS, and RCAS
modes. Measured in PV units/sec.
Setpoint Rate Down

SP_RATE_DN
28
> = 0
Data Type: Float

The ramp rate for SP down in AUTO, CAS, and RCAS
modes. Measured in PV units/sec.
198
Instruction Manual
D103412X012
August 2012
View Lists
Table 473. DO Function Block, View 1
Index Number
Index Number
Parameter
ST_REV
Parameter
ST_REV
5.1
5.1
5.2
5.2
5.3
5.3
5.4
5.4
BLOCK_ERR
BLOCK_ERR
PV_D
PV_D
SP_D
SP_D
OUT_D
OUT_D
16
READBACK_D
16
READBACK_D
17
CAS_IN_D
17
CAS_IN
21
BKCAL_OUT_D
22
RCAS_IN_D
24
RCAS_OUT_D

Index Number
Parameter
ST_REV
11
PV_STATE
12
XD_STATE
13.1
GRANT_DENY.GRANT
13.2
GRANT_DENY.DENY

Index Number
Parameter
ST_REV
STRATEGY
ALERT_KEY
14
IO_OPTS
15
STATUS_OPTS
18
CHANNEL
19
FSTATE_TIME
20
FSTATE_VAL_D
24
SHED_OPT
27
SP_RATE_UP
28
SP_RATE_DN
199
Instruction Manual

August 2012
D103412X012

DISCRETE OUTPUT FUNCTION BLOCK
Quick Config
Alert Key
Process Value Discrete: Status
Process Value Discrete: Value
Setpoint Discrete: Status
Setpoint Discrete: Value
Common Config
Alert Key
I/O Options
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Advanced Config
Fault State Time
Fault State Value Discrete
Process Value State
Shed Options
Simulate Discrete: Simulate Status
Simulate Discrete: Simulate Value
Simulate Discrete: Transducer Status
Simulate Discrete: Transducer Value
Simulate Discrete: Simulate En/Disable
Static Revision
Status Options
Strategy
Transducer State
I/O Reference
DO Channel
Connectors
Back Calculation Output Discrete: Status
Back Calculation Output Discrete: Value
Cascade Input Discrete: Status
Cascade Input Discrete: Value
Output Discrete: Status
Output Discrete: Value
200
Online
Block Error
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Remote Cascade Input Discrete: Status
Remote Cascade Input Discrete: Value
Remote Cascade Output Discrete: Status
Remote Cascade Output Discrete: Value
Readback Discrete: Status
Readback Discrete: Value
Status
Block Error
Other
Tag Description
Grant Deny: Grant
Grant Deny: Deny
Block Alarm: Value
Setpoint Rate Up
Setpoint Rate Down
All
Characteristics
Static Revision
Tag Description
Strategy
Alert Key
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Block Error
Process Value State
Transducer State
Grant Deny: Grant
Grant Deny: Deny
I/O Options
Status Options
Readback Discrete: Status
Readback Discrete: Value
DO Channel
Fault State Time
Fault State Value
Remote Cascade Input Discrete: Status
Remote Cascade Input Discrete: Value
Shed Options
Remote Cascade Output Discrete: Status
Remote Cascade Output Discrete: Value
Block Alarm: Value
Setpoint Rate Up
Setpoint Rate Down
Instruction Manual
Detailed SetupDI Function Block
D103412X012
August 2012
Discrete Input Function Block

Overview
The Discrete Input (DI) function block (figure 429) processes a single discrete input from a field device and makes it
available to other function blocks. You can configure inversion and alarm detection on the input value. In the
DVC6200f digital valve controller, the discrete input function block can provide limit switch functionality and valve
position proximity detection. The DI function block supports mode control, signal status propagation, and simulation.
Figure 429. Discrete Input (DI) Function Block
DI
TRANSDUCER
BLOCK
OUT_D
OUT_D = The block output and status
Normally, the block is used in Automatic mode so that the process variable (PV_D [7]) is copied to the output (OUT_D
[8]). You can change the mode to Manual to disconnect the field signal and substitute a manuallyentered value for
the output. In this case, PV_D [7] continues to show the value that will become the OUT_D [8] when the mode is
changed to Automatic.
To support testing, you can enable simulation, which allows the measurement value to be supplied manually through
the SIMULATE_D [9] parameter. Figure 430 illustrates the internal components of the DI function block, and table
481 lists the definitions of the block parameters.
Figure 430. Discrete Input Function Block Schematic
Discrete Signal
FIELD_VAL_D
Alarm Detection
OUT_D
Invert Option
SIMULATE
PV_D
MODE
201
Instruction Manual
August 2012
D103412X012
Modes
The Discrete Input function block supports the following modes:
Manual (Man)The block output (OUT_D [8]) is disconnected from the field and set manually.
Automatic (Auto)The block algorithm determines output.
Out of Service (OOS)The block is not processed. The OUT_D [8] status is set to Bad: Out of Service. The
BLOCK_ERR [6] parameter shows Out of Service.
The Fieldbus Foundation specification requires that certain parameters in the function blocks have initial values of
uninitialized. In addition to setting the Resource block mode to AUTO, the control system or the user must change
those parameters from their uninitialized value to a valid value in order for the function block to move from the Out of
Service mode. For the DI function block, the CHANNEL [15] parameter must be initialized.
Status Handling
Under normal conditions, a Good: NonCascade status is passed through to OUT_D [8]. The block also supports the
Status Action On Failure and BLOCK_ERR [6] indications.
When SIMULATE_D [9] is enabled, FIELD_VAL_D [7], PV_D [7], and OUT_D [8] change to the simulated status. When
the block is set to Manual mode, OUT_D [7] is set to Good: Non-cascade, Constant status.
I/O Selection
To select the I/O associated with the discrete measurement, configure the value of the CHANNEL [15] parameter.
In the digital valve controller, the four classes of channels are
Valve travel
Open/Closed limit switch
Variable limit switch based on transducer block travel alarm settings.
Proximity position detection based on transducer block travel alarm settings.
The CHANNEL [15] parameter for each of the four DI blocks available in the digital valve controller may be set
independently to achieve the desired position detection. The DI block CHANNEL [15] definitions are listed in table
477. Refer to the following descriptions for details of the operation of these channels.
Valve Travel
Channel 23 provides valve travel.
0 = Closed, 1 = 100% open, 5 = 5% open, 10 = 10% open, 15 = 15% open, etc.
202
Instruction Manual
D103412X012
August 2012
Table 477. Channel Selection for the Discrete Input Function Block
Transducer Block Parameter(1)
Selection
Bit Number(2)
Transducer Block Index Number
23
TRAVEL_D
24
INST_ALERTS_ACTIVE:PROX_ACTIVE
74.5
33
0: Travel Open
N/A
25
74.5
1: Travel Closed
26
INST_ALERTS_ACTIVE:TRAVEL_ACTIVE
74.4
2: Travel Limit Lo Lo
27
74.4
4: Travel Limit Lo
28
74.4
3: Travel Limit Hi
29
74.4
1: Travel Limit Hi Hi
30
74.5
5: Proximity Lo Lo
31
74.5
4: Proximity Lo
32
74.5
3: Proximity Hi
33
74.5
2: Proximity Hi Hi
1. Refer to table 414 for parameter descriptions.

2. See pages 74 and 76, Travel ALerts and Prox Alerts, for information on accessing these alerts. Refer to Appendix F for information on accessing these alerts through DeltaV.
Open/Closed Limit Switch

Channels 24 and 25 provide valve open and closed limit switch functionality for the DI block. These channels will
detect if the valve position is more than the Travel Open Alert Point for open detection or less than the Travel Closed
Alert Point for closed detection. These channels provide an adjustable deadband to clear the detected position.
0= Not Active, 1= Active
Variable Limit Switch

Channels 26 through 29 provide variable limit switch functionality for the DI block. Trip points for this limit switch
functionality are based on the Travel Alert settings in the transducer Block. The DI function block provides the same
type of position detection as the travel alerts in the transducer block. Table 478 lists the transducer block parameters
used with DI block channels 26 through 29. Refer to Travel and Prox, on page 74 for more information on the
transducer block travel alerts.
Table 478. Transducer Block Parameters Used with Discrete Input Function Block Channels 26 through 29
(Variable Limit Switch)
Parameter Function
Lo Lo Limit Switch Trip Point
Travel Lo Lo Alert Deadband
Lo Lo Limit Switch Deadband
Lo Limit Switch Trip Point
Travel Lo Alert Deadband
Lo Limit Switch Deadband
Hi Limit Switch Trip Point
Travel Hi Alert Deadband
Hi Limit Switch Deadband
Hi Hi Limit Switch Trip Point
Travel Hi Hi Alert Deadband
Hi Hi Limit Switch Deadband
Valve Position Proximity Detection

Channels 30 through 33 provide valve position proximity detection for the DI block. The transducer block Travel Alert
Point and Travel Alert Deadband parameters are also used with the valve position proximity, but they provide a
different function. The Travel Alert Point for the selected channel determines the center point for the position to be
detected. The Travel Alert Deadband for the selected channel sets the upper and lower trigger points, or the width of
the proximity detection band. A 1% deadzone exists above and below this band that the travel must exceed to clear
203
Instruction Manual

August 2012
D103412X012
the detected position. Figure 431 illustrates the operation of the proximity detection function. Travel Alert Point
refers to Travel Lo Alert Point, Travel Hi Alert Point, Travel Lo Lo Alert Point, and Travel Hi Hi Alert Point in table 479.
Travel Alert Deadband refers to Travel Lo Alert Deadband, Travel Hi Alert Deadband, Travel Lo Lo Alert Deadband, and
Travel Hi Hi Alert Deadband in table 479.
Figure 431. Discrete Input Proximity Detection Function
DISCRETE INPUT
CLEARED
DEADZONE, 1% OF TRAVEL
Valve Position
TRIGGER POINT FOR DOWNWARD VALVE

TRAVEL DETERMINED BY TRAVEL ALERT
DEADBAND
CENTER POINT OF PROXIMITY DETECTION

DETERMINED BY TRAVEL ALERT POINT
DISCRETE INPUT SET
TRIGGER POINT FOR UPWARD VALVE TRAVEL

DETERMINED BY TRAVEL ALERT DEADBAND

Table 479 lists the transducer block parameters used for proximity detection with DI block channels 30 through 33.
Table 479. Transducer Block Parameters Used with Discrete Input Function Block Channels 30 through 33
Parameter Function
Lo Lo Proximity Detection Center Point
Travel Lo Lo Alert Deadband
Lo Lo Proximity Detection Width
Lo Proximity Detection Center Point
Travel Lo Alert Deadband
Lo Proximity Detection Width
Hi Proximity Detection Center Point
Travel Hi Alert Deadband
Hi Proximity Detection Width
Hi Hi Proximity Detection Center Point
Travel Hi Hi Alert Deadband
Hi Hi Proximity Detection Width
Field Value Processing

The Invert bit of the IO_OPTS [13] parameter may be used to logically invert the value of FIELD_VAL_D [17] before it is
stored as PV_D [7]. PV_FTIME [16] may
be used to set the length of time that FIELD_VAL_D [17] must be in a new state before that new state is reflected in
PV_D. The PV_D [7] value goes to the mode switch where it becomes OUT_D [8] when the actual mode is AUTO.
OUT_D [8] is also tested for an alarm state.
Note
Invert is the only I/O option that the DI block supports. You can set the I/O option only when the block mode is Out of Service.
204
Instruction Manual
D103412X012
August 2012
Alarm Detection
To select the state that initiates an input alarm, and to set discrete alarm substatus in the output, configure the
DISC_LIM [23] parameter. You can enter any value between 0 and 255. A value of 255 disables the alarm. When
OUT_D [8] matches the DISC_LIM [23] state, the discrete value of an alarm is set.
Block Errors
Table 480 lists conditions reported in the BLOCK_ERR [6] parameter. Conditions in italics are not applicable for the DI
Condition Number
Other (N/A)
Block Configuration ErrorCHANNEL set to 0 through 10 (uninitialized)
Simulate ActiveSimulate is enabled. Output does not reflect process conditions
Input failure/process variable has Bad statusThe hardware is bad or the transducer block mode is Out of Service
Output Failure (N/A)
10
11
Lost NV Data (N/A)
12
13
14
Power UpSet after powerup until actual mode is not Out of Service
15
Out of ServiceThe actual mode is Out of Service (OOS). The block is not being processed.
Action on Failure
In case of hardware failure, FIELD_VAL_D [17], PV_D [7], and OUT_D [8] change to a Bad status and the BLOCK_ ERR
[6] parameter shows Process Variable has Bad Status. If the transducer block mode is Out of Service, the status of
FIELD_VAL_D [17], PV_D [7], and OUT_D [8] is set to Bad:Out of Service.
Simulation
To support testing of the control strategy, you can enable the SIMULATE_D [9] parameter. Normally the measurement
value and status used for FIELD_VAL_D [17] in the DI block reflect actual process values as provided by the transducer
block. When the SIMULATE_D [9] parameter is enabled, value and status used for FIELD_VAL_D [17] is supplied by the
user manually. To enable simulation in the DI function block, the simulate jumper must be installed. For information
on the installation of this jumper, see the Installation section.
The SIMULATE_D [9] parameter has three components:
Simulate_D enable/disable determines whether the function block will use the actual process value and status, or
Simulate Value and Simulate Status.
Transducer Value and Status reflect the process values provided by the transducer block.
Simulate Value and Status may be entered by the user when enable/disable is set to enabled.
205
Instruction Manual

August 2012
D103412X012
To use simulate, first install the simulate jumper in the terminal box, then set Simulate_D enable/disable to enabled,
then enter the desired values for Simulate Value and Status.
When SIMULATE_D [9] is enabled, the Simulate Active bit of the BLOCK_ERR [6] parameter is set (refer to the Block
Errors description). When the simulate jumper is installed, the Simulate Jumper bit of the transducer block parameter
SELFTEST_STATUS [78] is set.
Figure 432 compares the operation of a standard discrete input to a proximity discrete input. With the standard
discrete input, the discrete input changes state when the valve position passes a configurable trip point. This can be
used to indicate if the valve position is above or below the trip point.
Figure 432. Proximity Discrete Input Compared to a Standard Discrete Input
STANDARD DISCRETE INPUT
DISCRETE
INPUT VALUE
PROXIMITY DISCRETE INPUT
Configurable
Band
DISCRETE
INPUT VALUE
1
0
With the proximity discrete input a configurable band can be established about a central point. Whenever the valve
position enters this configurable band, the discrete input changes state. A proximity discrete input is useful for
applications which require knowing the location of the valve when the valve is not near 0% or 100%.
DI Function Block Parameter List (table 481)

206
Instruction Manual
D103412X012
August 2012
Table 481. Discrete Input Function Block Parameter Definitions

Label
PARAMETER_NAME
Index
Number
RO /
RW
Block
Mode
Range
Initial Value
Description
The revision level of the static data associated
with the function block. The revision value will
be incremented each time a static parameter
value in the block is changed.
Static Revision
ST_REV
RO
N/A
0 to 65535
Tag Description
TAG_DESC
RW
ALL
7 bit ASCII
Spaces

The user description of the intended
application of the block.
Strategy
STRATEGY
RW
ALL
0 to 65535

The strategy field can be used to identify
grouping of blocks. This data is not checked or
processed by the block.
Alert Key
ALERT_KEY
RW
ALL
1 to 255

The identification number of the plant unit.
This information may be used in the host for
sorting alarms, etc.
Block Mode
MODE_BLK
5
OOS
MAN
AUTO
OOS until
block is
configured,
then last valid
target
OOS+MAN+AUTO
TARGET
5.1
RW
ALL
ACTUAL
5.2
RO
ALL
OOS
OOS+MAN+A
UTO
PERMITTED
5.3
RW
ALL
NORMAL
5.4
RO
ALL
Block Error
BLOCK_ERR
Process Value Discrete

PV_D
Output Discrete
OUT_D
Simulate Discrete
SIMULATE_D
RO
RO
AUTO
N/A
Defined Bits
Error
3: Simulate Active
7: Input Failure / Bad PV
Status
14: Powerup
15: OutofService
N/A
PV_D Status set equal to

Field_Val_D Status
OOS
MAN
OUT_STATE
Dynamic

0=Inactive
1=Active
This parameter reflects the error status
associated with the hardware or software
components associated with a block. Multiple
errors may be shown, see table 480.
Dynamic
Data Type: DS66

The process variable used in block execution.
Value is converted from Readback to show the
actuator position in the same units as the set
point value.
Data Type: DS66
The primary discrete value calculated as a
result of executing the function.
SIMULATE_STATUS
9.1
ALL
SIMULATE_VALUE
9.2
ALL
TRANSDUCER_STATUS
9.3
RO
ALL
TRANSDUCER_VALUE
9.4
RO
ALL
ENABLE/DISABLE
0
0=Not initialized
2=Simulation Active
9.5
Data Type: DS69

Valid Bits: 7:OOS, 4:MAN, 3:AUTO
modes of the block.
1=Simulation
Disabled
Data Type: DS83

Allows the transducer discrete input or output
to the block to be manually supplied when
simulate is enabled. When simulation is
disabled, the simulate value and status track
the actual value and status.
Transducer State
XD_STATE
10
ALL
Data Type: Uint16

Index to the text describing the states of a
discrete for the value obtained from the
transducer.
Output State
OUT_STATE
11
ALL

Index to the text describing the states of a
discrete output.
-Continued-
207
Instruction Manual

August 2012
D103412X012
Table 481. Discrete Input Function Block Parameter Definitions (Continued)

Label
PARAMETER_NAME
Grant Deny
GRANT_DENY
Index
Number
RO /
RW
Block
Mode
12.1
ALL
DENY
12.2
ALL
Status Options
STATUS_OPTS
DI Channel
CHANNEL
13
14
15

PV_FTIME
16
Field Value Discrete

FIELD_VAL_D
17
Update Event
UPDATE_EVT
18
UNACKNOWLEDGED
18.1
0: Program
1: Tune
2: Alarm
3: Local
All bits: 0
Data Type: DS70

Options for controlling access of host
computers and local control panels to
operating, tuning, and alarm parameters of
the block.
GRANT: 0=NA, 1=granted
DENY: 0=NA, 1=denied
All bits:0
OOS
3=Propagate Failure
Forward
8=Uncertain in MAN mode
All bits:0

0=Disable
1=Enable
Options the user may select for the block
processing of status.
OOS
0=undefined
23=Valve Position or
Pressure (Discrete)
24= PV > 97%
25= PV < 3%
26=PV Below LO LO limit
27=PV Below LO limit
28=PV Above HI limit
29=PV Above HI HI limit
30=PV Within Proximity of
LO LO
31=PV Within Proximity of
LO
32=PV within Proximity of
HI
33=PV within Proximity of
HI HI
0=Undefined

Defines the functionality of the discrete input.
See I/O Selection for details. Refer to table
477.
Data Type: Float

Time that FIELD_VAL_D must be in a new
state, before the change is reflected to PV_D
and OUT_D.
Data Type: DS66

Raw value of the field device discrete input,
with a status reflecting the transducer
condition.
OOS
0: Invert
ALL
Positive
RO
RW
All bits:0
Description

0=Disable
1=Enable
Allows you to select how the I/O signals are
processed.
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
0=Undefined
1=Update Reported
2=Updated not reported
0=Undefined
UPDATE_STATE
18.2
RO
N/A
TIME_STAMP
18.3
RO
N/A
STATIC_REVISION
18.4
RO
N/A
RELATIVE_INDEX
18.5
RO
N/A
0
-Continued-
208
Initial Value
12
GRANT
I/O Options
IO_OPTS
Range
Data Type: DS73

This alert is generated by any change to the
static data.
Instruction Manual
D103412X012
August 2012
Table 481. Discrete Input Function Block Parameter Definitions (Continued)

Label
PARAMETER_NAME
Block Alarm
BLOCK_ALM
UNACKNOWLEDGED
Index
Number
RO /
RW
Block
Mode
19
19.1
Initial Value
Description
Dynamic
RW
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clear reported
3=Active reported
ALARM_STATE
19.2
RO
N/A
TIME_STAMP
19.3
RO
N/A
SUBCODE
19.4
RO
N/A
VALUE
19.5
RO
Alarm Summary
ALARM_SUM
Range
Data Type: DS72

hardware, connection failure, or system
problems in the block. The cause of the alert is
entered in the subcode field. The first alert to
become active will set the active status in the
status parameter. As soon as the unreported
status is cleared by the alert reporting
procedure, and other block alert may be
reported without clearing the active status, if
the subcode has changed.
0: Discrete alarm
7: Block Alarm
20
CURRENT
20.1
RO
All bits: 0
UNACKNOWLEDGED
20.2
RO
All bits: 0
UNREPORTED
20.3
RO
All bits: 0
DISABLED
20.4
RW
All bits: 0
Data Type: DS74

The current alert status, unacknowledged
states, unreported states, and disabled states
of the alarms associated with the function
block.
0=clear reported
0=acknowledged
0=reported
0=enabled
0=Disable
1=Enable
Used to set auto acknowledgement of alarms
Acknowledge Option
ACK_OPTION
21
ALL
0: Discrete
1: Block Alarm
Discrete Priority
DISC_PRI
22
ALL
0 to 15

Priority of the discrete alarm.
Discrete Limit
DISC_LIM
23
ALL
PV_STATE

State of discrete input which will generate an
alarm.
Discrete Alarm
DISC_ALM
24
N/A
0=Undefined
1=Acknowledged
2=Unacknowledged
0=Undefined
1=Clear reported
3=Active reported
UNACKNOWLEDGED
24.1
RW
ALARM_STATE
24.2
RO
N/A
TIME_STAMP
24.3
RO
N/A
SUBCODE
24.4
RO
N/A
VALUE
24.5
RO
N/A
All bits: 0
Data Type: DS72

The discrete alarm is used for indication of a
state change in selected discrete channel.
209
Instruction Manual

August 2012
D103412X012
View Lists
Table 482. DI Function Block, View 1
Index Number
Index Number
Parameter
ST_REV
5.1
5.1
5.2
5.2
5.3
5.3
5.4
5.4
BLOCK_ERR
BLOCK_ERR
PV_D
PV_D
OUT_D
OUT_D
17
FIELD_VAL_D
17
FIELD_VAL_D
20.1
ALARM_SUM.CURRENT
20.1
ALARM_SUM.CURRENT
20.2
20.2
20.3
20.3
20.4
ALARM_SUM.DISABLED
20.4
ALARM_SUM.DISABLED

Index Number
210
Parameter
ST_REV
Parameter
ST_REV
10
XD_STATE
11
OUT_STATE
12.1
GRANT_DENY.GRANT
12.2
GRANT_DENY.DENY

Index Number
Parameter
ST_REV
STRATEGY
ALERT_KEY
13
IO_OPTS
14
STATUS_OPTS
15
CHANNEL
16
PV_FTIME
21
ACK_OPTION
22
DISC_PRI
23
DISC_LIM
Instruction Manual
D103412X012
August 2012

DISCRETE INPUT FUNCTION BLOCK
Quick Config
Alert Key
Common Config
Alert Key
Discrete Limit
I/O Options
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Online
Block Error
Field Value Discrete: Status
Field Value Discrete: Value
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Status
Block Error
Advanced Config
Other
DI Channel
Output State
Static Revision
Status Options
Transducer State
Connectors
Strategy
Tag Description
Grant Deny: Grant
Grant Deny: Deny
Block Alarm: Value
Acknowledge Option
Discrete Alarm: Unacknowledged
Discrete Alarm: Alarm State
Discrete Alarm: Time Stamp
Discrete Alarm: Subcode
Discrete Alarm: Discrete Value
All
Characteristics
Static Revision
Tag Description
Strategy
Alert Key
Block Mode: Target
Block Mode: Actual
Block Mode: Normal
Block Error
Transducer State
Output State
Grant Deny: Grant
Grant Deny: Deny
I/O Options
Status Options
DI Channel
Field Value Discrete: Status
Field Value Discrete: Value
Block Alarm: Value
Acknowledge Option
Discrete Priority
Discrete Limit
Discrete Alarm: Unacknowledged
Discrete Alarm: Alarm State
Discrete Alarm: Time Stamp
Discrete Alarm: Subcode
Discrete Alarm: Discrete Value
211

August 2012
212
Instruction Manual
D103412X012
Instruction Manual
Calibration
D103412X012
August 2012
Section 5 Calibration 5-5Calibration Overview

When a DVC6200f digital valve controller is ordered as part of a control valve assembly, the factory mounts the digital
valve controller on the actuator and connects the necessary tubing, then sets up and calibrates the controller.
For digital valve controllers that are ordered separately, recalibration of the pressure sensors generally is unnecessary.
However, after mounting on an actuator, perform the initial setup then calibrate travel by selecting Configure / Setup >
Calibration > Auto Calibration. For more detailed calibration information, refer to the following calibration procedures.
Calibration
Field Communicator
TB > Configure/Setup > Calibration
Auto Calibration This procedure automatically calibrates the travel. The calibration procedure uses the valve and
actuator stops as the 0% and 100% calibration points. See page 214.
Manual Calibration This procedure permits manual calibration of the travel. This calibration procedure allows you
to determine the 0% and 100% calibration points. See page 214.
Relay This procedure permits adjustment of the pneumatic relay. See page 215.
Supply Pressure This procedure permits calibrating the supply pressure sensor. Normally the sensor is calibrated at
the factory and should not need calibration. See page 216.
Pressure A This procedure permits calibrating the pressure A sensor. Normally the sensor is calibrated at the
factory and should not need calibration. See page 217.
Pressure B This procedure permits calibrating the pressure B sensor. Normally the sensor is calibrated at the
factory and should not need calibration. See page 217.
Note
The Instrument Mode must be Out Of Service and the Protection set to None before the instrument can be calibrated.
If you are operating in burst mode, we recommend that you disable burst before continuing with calibration. Once calibration is
complete, burst mode may then be turned back on.
WARNING
During calibration the valve will move full stroke. To avoid personal injury and property damage caused by the release of
process fluid.
213
Instruction Manual
Calibration
August 2012
D103412X012
If a doubleacting relay is used, you will be prompted to run the relay adjustment when auto or manual calibration is
selected. Select Yes to adjust the relay, select No to proceed with calibration. For additional information, refer to Relay
Adjustment in this section.
Note
Relay Adjustment is only available for the doubleacting relay (Relay A).
Auto Calibration
Field Communicator
TB > Configure/Setup > Calibration > Auto Calibration
Follow the prompts on the Field Communicator display to automatically calibrate travel.
1. The auto calibration procedure is automatic. It is completed when the Calibration menu appears.
During calibration, the instrument seeks the high and low end points and the minor loop feedback (MLFB) and output
bias. By searching for the end points, the instrument establishes the limits of physical travel, i.e. the actual travel 0 and
100% positions. This also determines how far the relay beam swings to calibrate the sensitivity of the MLFB sensor.
2. Place the instrument In Service and verify that the travel properly tracks the current source.
Manual Calibration
Field Communicator
TB > Configure/Setup > Calibration > Manual Calibration
Note
0% Travel = Valve Closed ; 100% Travel = Valve Open
1. From the adjustment menu, select the direction and size of change required to set the travel at 0% (move the valve
to close). Selecting large, medium, and small adjustments causes changes of approximately 10.0%, 1.0%, and 0.1%,
respectively, to the travel feedback movement. Selecting Next will implement the adjustment.
If another adjustment is required, repeat step 1. Otherwise, select Done and go to step 2.
2. From the adjustment menu, select the direction and size of change required to set the travel to 100% (move the
valve to open).
If another adjustment is required, repeat step 2. Otherwise, select Done and go to step 3.
3. Enter the name of the person performing the calibration procedure.
4. Enter the location of the calibration procedure.
5. Enter the date of the calibration procedure.
6. Place the Transducer Block Mode in Manual and verify that the travel properly tracks the setpoint changes.
214
Instruction Manual
Calibration
D103412X012
August 2012
Relay
Field Communicator
TB > Configure/Setup > Calibration > Relay
Follow the prompts on the Field Communicator display to check relay adjustment. Replace the digital valve controller
cover when finished.
Note
Relay B and C are not useradjustable.
DoubleActing Relay
The doubleacting relay is designated by Relay A on a label affixed to the relay itself. For doubleacting actuators, the
valve must be near midtravel to properly adjust the relay. The Field Communicator will automatically position the
valve when Relay is selected.
CAUTION
Care should be taken during relay adjustment as the adjustment disc may disengage if rotated too far.
Rotate the adjustment disc, shown in figure 51, until the output pressure displayed on the Field Communicator is
between 50 and 70% of supply pressure. This adjustment is very sensitive. Be sure to allow the pressure reading to
stabilize before making another adjustment (stabilization may take up to 30 seconds or more for large actuators).
Figure 51. Relay A Adjustment (Shroud Removed for Clarity)
FOR SINGLEACTING DIRECT

RELAYS: ROTATE ADJUSTMENT
DISC IN THIS DIRECTION UNTIL IT
CONTACTS THE BEAM
FOR DOUBLEACTING RELAYS:
ROTATE ADJUSTMENT DISC IN
THIS DIRECTION TO DECREASE
OUTPUT PRESSURE
ADJUSTMENT DISC
FOR DOUBLEACTING RELAYS:

ROTATE ADJUSTMENT DISC IN
THIS DIRECTION TO INCREASE
OUTPUT PRESSURE
W9034
215
Instruction Manual
Calibration
August 2012
D103412X012
If the low bleed relay option has been ordered stabilization may take approximately two minutes longer than the
standard relay.
Relay A may also be adjusted for use in singleacting direct applications. Rotate the adjustment disc as shown in figure
51 for singleacting direct operation.
SingleActing Relays
WARNING
For instrument level PD only:
If the unused port is monitoring pressure, ensure that the pressure source conforms to ISA Standard 7.0.01 and does not
exceed the pressure supplied to the instrument.
Failure to do so could result in personal injury or property damage caused by loss of process control.
SingleActing Direct Relay

The singleacting direct relay is designated by Relay C on a label affixed to the relay itself. Relay C requires no
adjustment.
SingleActing Reverse Relay
The singleacting reverse relay is designated by Relay B on a label affixed to the relay itself. Relay B is calibrated at the
factory and requires no further adjustment.
Supply Pressure Sensor

Field Communicator
TB > Configure/Setup > Calibration > Supply Pressure
Note
The pressure sensor is calibrated at the factory and should not require calibration.
To calibrate the supply pressure sensor, connect an external reference gauge to the output side of the supply
regulator. The gauge should be capable of measuring maximum instrument supply pressure. Select Follow the
prompts on the Field Communicator display to calibrate the instrument's supply pressure sensor.
1. Select a) Zero Only, or b) Zero and Span (gauge required).
a. If Zero Only calibration is selected, adjust the supply pressure regulator to remove supply pressure from the
instrument. Press OK. Once calibration is complete, go to step 5.
b. If Zero and Span calibration is selected, adjust the supply pressure regulator to remove supply pressure from the
instrument. Press OK. Adjust the supply regulator to the maximum instrument supply pressure. Press OK.
Proceed with step 2.
216
Instruction Manual
D103412X012
Calibration
August 2012
2. The following message appears:

Use the Increase and
Decrease selections until
the displayed pressure
matches the instrument
supply pressure.
Press OK when you have read this message.
3. The value of the pressure appears on the display.
4. From the adjustment menu, select the direction and size of adjustment to the displayed value. Selecting large,
medium, and small adjustments causes changes of approximately 3.0 psi/0.207 bar/20.7 kPa, 0.30 psi/0.0207
bar/2.07 kPa, and 0.03 psi/0.00207 bar/0.207 kPa, respectively. Adjust the displayed value until it matches the
supply pressure, select Done and go to step 5.
5. Place the instrument In Service and verify that the displayed pressure matches the measured supply pressure.
Pressure A or B Sensor
Field Communicator
TB > Configure/Setup > Calibration > Pressure A
Field Communicator
TB > Configure/Setup > Calibration > Pressure B
To calibrate the output pressure sensor, connect an external reference gauge to the output being calibrated. The
gauge should be capable of measuring maximum instrument supply pressure. Select . Follow the prompts on the Field
Communicator display to calibrate the instrument's output pressure sensor.
1. Adjust the supply pressure regulator to the maximum instrument supply pressure. Press OK.
2. The instrument reduces the output pressure to 0. The following message appears.
Decrease selections
until the displayed
pressure matches the
output x pressure.
Press OK when you have read the message.
3. The value of the output pressure appears on the display. Press OK to display the adjustment menu.
4. From the adjustment menu, select the direction and size of adjustment to the displayed value. Selecting large,
medium, and small adjustments causes changes of approximately 3.0 psi/0.207 bar/20.7 kPa, 0.30 psi/0.0207
bar/2.07 kPa, and 0.03 psi/0.00207 bar/0.207 kPa, respectively. If the displayed value does not match the output
pressure, press OK, then repeat this step (step 4) to further adjust the displayed value. When the displayed value
matches the output pressure, select Done and go to step 5.
217
Instruction Manual
Calibration
August 2012
D103412X012
5. The instrument sets the output pressure to full supply. The following message appears.
Decrease selections
until the displayed
pressure matches the
output x pressure.
Press OK when you have read the message.
6. The value of the output pressure appears on the display. Press OK to display the adjustment menu.
7. From the adjustment menu, select the direction and size of adjustment to the displayed value. If the displayed value
does not match the output pressure, press OK, then repeat this step (step 7) to further adjust the displayed value.
When the displayed value matches the output pressure, select Done and go to step 8.
8. Place the instrument In Service and verify that the displayed pressure matches the measured output pressure.
218
Instruction Manual
Viewing Device Variables and Diagnostics
D103412X012
August 2012
Section 6 Viewing Device Variables and Diagnostics6-6View Lists

View Lists allow the values of a set of parameters to be accessed at the same time. View lists are available for the
resource and transducer blocks, and the function blocks.
Resource Blocktables 44 through 47
OS Function Blocktables 449 through 452
Transducer Blocktables 415 through 423
AI Function Blocktables 458 through 461
AO Function Blocktables 426 through 429
MAI Function Blocktables 465 through 468
PID Function Blocktables 433 through 437
DO Function Blocktables 473 through 476
IS Function Blocktables 441 through 444
DI Function Blocktables 482 through 485
Note
Views Lists are used by hosts for efficient monitoring of multiple parameters. Normally you will not be aware of view list usage, as
they are hidden by the host software.
Resource Block
This section contains information on the DVC6200f digital valve controller resource block. The resource block defines
the physical resources of the device. The resource block also handles functionality that is common across multiple
blocks. The block has no linkable inputs or outputs.
Table 61. Resource Block BLOCK_ERR Conditions
Condition Number
Other Set if a device initialization error occurred.
Block Configuration Error Set if FEATURE_SEL, CYCLE_SEL, or CYCLE_TYPE is set incorrectly.
Link Configuration Error N/A
Local Override N/A
Device Fault State N/A
Device Needs Maintenance Soon Indicates a Maintenance PlantWeb Alert condition is active.
Input failure/process variable had Bad status N/A
Output failure N/A
Memory failure Indicates a pending Flash or NVM failure.
10
Lost Static Data Indicates failure of the memory containing static parameters
11
Lost NV Data Indicates failure of the memory containing nonvolatile parameters.
12
Readback Check Failed NA
13
Device Needs Maintenance Now Indicates a Failed PlantWeb Alert condition is active.
14
Power Up Indicates the device has been powered up and the Resource Block is not running normally.
15
Out of Service (MSB) The resource block actual mode is Out of Service.
219
Instruction Manual
August 2012
D103412X012
Device Diagnostics
Resource Block Error
(RB > Device Diagnostics > Resource Block Error)
Field Communicator
RB > Device Diagnostics > Resource Block Error
Block Error (BLOCK_ERR [6]) indicates an error status associated with hardware or software for the resource block.
resource block and are provided only for your reference.
Device State
Field Communicator
RB > Device Diagnostics > Device State
Device State (RS_STATE [7]) indicates the state of the function blocks. Four states are possible:
InitializationThe instrument enters this state upon restart or failure. The function blocks are in the IMan mode.
During the initialization state, all unreported function block alarms are automatically confirmed and acknowledged.
Once the instrument is considered operational, block execution is scheduled and the instrument state moves to
Online.
OnlineThe instrument will be in this state if it is operational. The function blocks are initially in the Auto mode, but
can be changed to a higher level mode.
StandbyThe instrument enters this state if the resource block mode is Out of Service (OOS). In this state all
function block modes are forced to Out of Service. The transducer block mode is not affected. When the resource
block mode is changed to Auto, the instrument state moves to Online.
Failure The instrument moves to this state whenever a hardware or memory failure is detected which would
prevent reliable operation. All function blocks and the transducer block modes are Out of Service.
Write Lock
Field Communicator
RB > Device Diagnostics > Write Lock
Write Alarm: Alarm State

Write Lock
Write Lock (WRITE_LOCK [34]) determines if writes are permissible to other device parameters. The Soft Write Lock
feature must be selected to be able to use Write Lock (see Selecting Features). When Write Lock is set to Locked, no
writes are permitted to any parameters within the device except to set Write Lock to Not Locked. When locked, the
block functions normally, updating inputs and outputs and executing algorithms. When Write Lock is set to Not
Locked, the Write Alarm alert is active.
220
Instruction Manual
D103412X012
August 2012
Block Alarm
Field Communicator
RB > Device Diagnostics > Block Alarm
The Block Alarm (BLOCK_ALM [36]) is used for all configuration, hardware, connection failure or system problems in
the block.
Block Alarm: Alarm State (BLOCK_ALM. ALARM_STATE [36.2]) indicates the state of the Block Alarm. Five states are
possible:

Undefined
Clear reported
Clear not reported
Active reported
Active not reported

Block Alarm: Unacknowledged (BLOCK_ALARM. UNACKNOWLEDGED [36.1])
1 = Undefined
2 = Acknowledged
3 = Unacknowledged
Maintenance
Field Communicator
RB > Device Diagnostics > Maintenance
Restart Actions
WARNING
Restarting the instrument may cause loss of process control. To avoid personal injury and property damage caused by the
release of pressure of process fluid, isolate the valve from the process and equalize pressure on both sides of the valve or
bleed off the process fluid.
You can restart the instrument to reset parameters, links, etc. within the instrument. However, due to the effect that a
restart can have on the instrument, and therefore the control loop, restarting the instrument should be used
cautiously and only as a last measure. The following procedure describes how to use Restart Options to restart the
instrument with a Field Communicator. You can also restart the instrument using ValveLink software or from a host
system using the Restart method included with the device description (DD) software.
You can restart the instrument any time it is connected to an active segment.
Field Communicator
RB > Device Diagnostics > Maintenance > Restart Actions
1. Restart informs you about what can happen when an instrument restart is performed. Select Yes to continue, or No
to abort without restarting.
2. Select the desired restart action or select EXIT to exit Restart. Select Help (not the Help button) to get information
on restart actions.
221
Instruction Manual
August 2012
D103412X012
There are two different restarts: Restart Processor, and Restart with Defaults:
When selecting either of these options, Restart informs you of the consequences of this action and asks if you want to
continue. Select Yes to perform the restart action, select No to select another action or exit. Restart informs you when
the restart is completed. You must acknowledge the message to continue.
Restart ProcessorPerforming a Restart Processor has the same effect as removing power from the instrument and
reapplying power. Configuration and calibration do not change.
Restart with DefaultsPerforming a Restart with Defaults should be done with care. This restart resets most of the
static and nonvolatile parameters for all of the blocks in the instrument to their initial value, as listed in table 42. After
a Restart with Defaults, you should place the instrument in service (the transducer block mode to auto) and run Device
Setup and download the instrument configuration from the control system to properly setup the instrument. You also
may need to reestablish communication links and trends.
Fault StateFault State (FAULT_STATE [28]), when active, indicates that the resource block is currently forcing the
output block to perform its FSTATE action. Selecting Fault State enables the ability to manually set and clear the
fault state.
Set Fault StateSelecting Set Fault State (SET_FSTATE [29]) changes the Fault State (FAULT_STATE [28]) to Active.
Setting Set FState (SET_FSTATE [29]) to SET manually places the instrument in the fault state.
Clear Fault StateSetting Clear FState (CLR_FSTATE [30]) to CLEAR clears the device fault state, if no faults are
currently active. You can test the actions the output blocks will perform by manually setting fault state active.
Device Variables
Instrument
Field Communicator
RB > Device Variables > Instrument
The following parameters are contained in the the Instrument menu of the resource block.
Identification
Device IDThe 32 character Device ID (DEVICE_ID [54]).
Electronics Serial NumberThe Electronics Serial Number (ELECTRONICS_SN [49]) set at the factory.
Factory Serial NumberThe Factory Serial Number (FACTORY_SN [50]) is the instrument serial number set at the
factory.
Field Serial NumberThe Field Serial Number (FIELD_SN [51]) is the serial number of the valve and actuator on
which the instrument is mounted.
Tag DescriptionThe Tag Description (TAG_DESC [2]) is unique description of each block within the digital valve
controller, used to describe the intended application for the block. Follow the prompts on the Field Communicator
to enter an up to 32 character description for the block in the Tag Description field. (This parameter is read/write.)
StrategyStrategy (STRATEGY [3]) permits strategic grouping of blocks so the operator can identify where the
block is located. The blocks may be grouped by plant area, plant equipment, etc. Enter a value between 0 and
65535 in the Strategy field.
222
Instruction Manual
D103412X012
August 2012
ManufacturerManufacturer Identification (MANUFAC_ID [10]) identifies the manufacturer of the instrument. It is

used by the host system to locate the DD file for the device. For Fisher the Manufacturer ID is 0x5100.
Device TypeDevice Type (DEV_TYPE [11]) identifies the type of device. It is used by the host system to locate the
DD file for the device. For a DVC6200f digital valve controller with Standard Control the device type is 0x4602.
Version
Device RevisionDevice Revision (DEV_REV [12]) identifies the device revision number. It is used by the host system
to locate the DD file for the device.
Firmware RevisionFirmware Revision (FIRMWARE_REV_ALL [47.6]) shows all device firmware revisions currently in
operation.
Standby Firmware RevisionStandby Firmware Revision (STBY_FIRMWARE_REV_ALL [55.6]) shows all device
firmware revisions currently in standby.
Hardware RevisionHardware Revision(HARDWARE_REV[48]) identifies the electronic hardware revision.
ITK VersionITK Version (ITK_VER [41]) identifies the major version of the Interoperability Tester used by the
Fieldbus Foundation in certifying the device as interoperable. This device revision meets the requirements of
version 5.
Options
Field Communicator
RB > Device Variables > Options
The following parameters are contained in the the Options menu of the resource block.
Diagnostic OptionsDiagnostic Options (DIAG_OPTIONS [45]) shows the diagnostic options available in the
instrument.
Function Block OptionsFunction Block Options (FB_OPTIONS [44]) shows which function blocks are licenced and
enabled in the instrument.
Miscellaneous OptionsMiscellaneous Options (MISC_OPTIONS [46]) indicates which miscellaneous licensing
options are enabled.
Features AvailableFeatures (FEATURES [17]) shows the supported resource block options.
DD Information
Field Communicator
RB > Device Variables > DD Information
DD Information contains information about the Device Description (DD).
Transducer Block
This section contains information on the DVC6200f digital valve controller transducer block. Descriptions of all
transducer block parameters are included. The transducer block decouples function blocks from the local output
functions required to command output hardware. The transducer block typically contains setup and calibration
information.
223

August 2012
Instruction Manual
D103412X012
Device Diagnostics
Active PlantWeb Alerts
Field Communicator
TB > Device Diagnostic > Active PlantWeb Alerts
To view the active PlantWeb alerts select Active PlantWeb Alerts.
Alert Conditions
Field Communicator
TB > Device Diagnostic > Active Conditions
The alert conditions for each group of alerts are listed below. If there are no alerts active for a particular group the
group will not be displayed on the Field Communicator.
Electronicsif an electronics alert is active it will appear under ELECT ALERTS
Drive Current
Drive Current AlertThis alert is active when the difference between the expected Drive Current and the actual Drive
Current has exceeded the Drive Current Alert Time.
Drive Signal
Drive Signal AlertThe Drive Signal Alert is active if one of the following conditions exist:
Where Zero Power Condition is defined as closed:
Drive Signal < 10% and Calibrated Travel > 3%
Drive Signal > 90% and Calibrated Travel < 97%
Where Zero Power Condition is defined as open:
Drive Signal < 10% and Calibrated Travel < 97%
Drive Signal > 90% and Calibrated Travel > 3%
Processor Impaired
Program Memory AlertThis alert is active if a pending flash or NVM failure is present.
Static Memory AlertThis alert is active when there is a failure of the FRAM memory where static parameters are
stored.
Processor AlertThis alert is active when there is a failure of the main processor.
I/O Processor AlertThis alert is active when there is a failure of the I/O processor.
ConfigurationIf a configuration alert is active it will appear under CONFIG ALERTS
Output Block Timeout AlertThis alert is active if the output block has not executed for a period of time longer than
the configured timeout.
224
Instruction Manual
D103412X012
August 2012

Blocks Set to Default AlertThis alert is active if the resource block has undergone Restart with Defaults. This will stay
active until the transducer block is changed from Out of Service.
SensorIf a configuration alert is active it will appear under SENSOR ALERTS
Travel Sensor
Travel SensorThis alert is active if the Travel Sensor reading is outside the functional range, or the sensor becomes
disconnected.
Pressure Sensors
Pressure A Sensor AlertThis alert is active if the Port A Pressure Sensor reading is outside the functional range.
Pressure B Sensor AlertThis alert is active if the Port B Pressure Sensor reading is outside the functional range.
Supply Pressure Sensor AlertThis alert is active if the Pressure Sensor reading is outside the functional range.
Pressure Fallback
Pressure Fallback AlertThis alert is active if a travel sensor failure or a gross travel deviation has resulted in fallback to
pressure control.
Temperature Sensor
Temperature Sensor AlertThis alert is active if the temperature sensor reading is outside the functional range of the
sensor.
EnvironmentIf an environment alert is active it will appear under ENVIRO ALERTS
Supply Pressure
Supply Pressure Hi AlertThis alert is active if the supply pressure exceeds the Supply Pressure Hi Alert.
Supply Pressure Lo AlertThis alert is active if the supply pressure exceeds the Supply Pressure Lo Alert.
Temperature Limit
Temperature Hi AlertThis alert is active if the temperature is greater than the Temperature Hi Alert Point.
Temperature Lo AlertThis alert is active if the temperature is greater than the Temperature Lo Alert Point.
TravelIf a travel alert is active it will appear under TRAVEL ALERTS
Travel Deviation
Travel Deviation AlertThis alert is active if the Travel deviation exceeds the Travel Deviation Alert Point by more than
the Travel Deviation Time.
Travel Limit
Travel Limit Hi Hi AlertThis alert is active if Travel exceeds the Travel Limit Hi Hi Alert point.
Travel Limit Lo Lo AlertThis alert is active if Travel is lower than the Travel Limit Lo Lo Alert point.
Travel Hi/Lo
Travel Limit Hi AlertThis alert is active if Travel exceeds the Travel Limit Hi Alert point.
Travel Limit Lo AlertThis alert is active if Travel is lower than the Travel Limit Lo Alert point.
ProximityIf a proximity alert is active it will appear under PROX ALERTS
Travel Open
Travel Open AlertThis alert is active if the travel is greater than the travel open alert point.
225
Instruction Manual
August 2012
D103412X012
Travel Closed
Travel Closed AlertThis alert is active if the travel is greater than the travel closed alert point.
Proximity
Proximity Hi Hi AlertThis alert is active if the Travel is within the detection band set by the Travel Hi Hi Alert Point
and the Travel Hi Hi Deadband.
Proximity Hi AlertThis alert is active if the Travel is within the detection band set by the Travel Hi Alert Point and the
Travel Hi Deadband.
Proximity Lo AlertThis alert is active if the Travel is within the detection band set by the Travel Lo Alert Point and the
Travel Lo Deadband.
Proximity Lo Lo AlertThis alert is active if the Travel is within the detection band set by the Travel Lo Lo Alert Point
and the Travel Lo Lo Deadband.
Travel HistoryIf a travel history alert is active it will appear under TVL HIST ALERTS
Cycle Counter
Cycle Counter AlertThis alert is active if the Cycle Counter exceeds the Cycle Count Alert Point.
Travel Accumulator
Travel Accumulator AlertThis alert is active if the Travel Accumulator exceeds the Travel Accumulator Alert Point.
Performanceif a performance alert is active it will appear under PERF ALERTS
Performance Critical AlertThis alert is active if the instrument is no longer able to control the valve or performance
has been dramatically reduced.
Performance Reduced AlertThis alert is active if the instrument has detected a reduction in performance.
Performance Information AlertThis alert is active if the instrument has detected a condition that may pertain to
control performance.
Status
Field Communicator
TB > Device Diagnostic > Status
Self Test Status

Integrator SuspendedThe integrator function is temporarily suspended. The integrator is suspended if any of the
following conditions are met:
The setpoint and actual travel are greater than 98% or less than 2%.
The set point is in cutoff
The Transducer block is Out of Service (OOS)
Integrator Limited LoIndicates the integrator reached its limit and cannot move the valve any further. High valve
friction may cause this situation.
Integrator Limited HiIndicates the integrator reached its limit and cannot move the valve any further. High valve
friction may cause this situation.
226
Instruction Manual
D103412X012
August 2012
Travel Sensor Span ErrorIndicates that span between the endpoints of travel are not far enough apart. This error is
reported during automatic calibration.
MLFB ErrorIndicates that the Minor Loop Feedback sensor gave a nonvalid value during automatic calibration.
Travel Sensor Hi ErrorIndicates the travel sensor has reported a travel position that is significantly above the normal
Travel Sensor Lo ErrorIndicates the travel sensor has reported a travel position that is significantly below the normal
Pressure B Sensor FailureIndicates the pressure sensor is reporting a pressure that is significantly outside of the normal
Pressure A Sensor FailureIndicates the pressure sensor is reporting a pressure that is significantly outside of the normal
Supply Sensor FailureIndicates the pressure sensor is reporting a pressure that is significantly outside of the normal
IOP FailureIndicates the I/O processor has failed.
Drive Current AlertIndicates that the Drive Current has exceeded the Drive Current Alert Point for more than the Drive
Current Alert Time.
Simulate Jumper ONIndicates the simulate jumper is connected to the DVC6200f between the two AUX terminals.
Block Error
Table 62 lists conditions reported in the BLOCK_ERR [6] and XD_ERROR [11] parameters. Conditions in italics are not
applicable for the transducer block and are provided only for your reference.
Table 62. Transducer Block BLOCK_ERR and XD_ERROR Conditions
Condition Number
Other (N/A)
Block Configuration Error Indicates that one of the following parameters have been configured out of the proper range: 15,
16, 47.1, 47.2, 46.3, 46.5, 42.7, 42.8.
Simulate Active Indicates that alerts are being simulated. This is not an indication that the I/O blocks are using simulation
data. See AO block parameter SIMULATE [10] and DO block parameter SIMULATE_D [10].
Device Fault State - (NA)
Maintenance Needed Soon (N/A)
Output failure (N/A)
Memory failure (N/A)
10
Lost Static Data Indicates that manufacturing functional or thermal tests were incomplete
11
Lost NV Data (N/A)
12
13
Device Needs Maintenance Now Indicates that manufacturing functional or thermal tests were incomplete
14
Power Up (N/A)
15
Out of Service Indicates Out of Service Mode.
227
Instruction Manual
August 2012
D103412X012
Device Record
Field Communicator
TB > Device Diagnostic > Device Record
The following parameters are contained in the Device Record menu of the transducer block.
Maximum Recorded TemperatureMaximum Recorded Temperature (TEMP_MAX [86.1]) shows the maximum
temperature the instrument has experienced since installation.
Maximum Recorded Temperature TimeMaximum Recorded Temperature Time (TEMP_MAX_TIME [86.2]) shows
the date and time when the Temperature Maximum occurred.
Minimum Recorded TemperatureMinimum Recorded Temperature (TEMP_MIN [86.3]) shows the minimum
temperature the instrument has experienced since installation.
Minimum Recorded Temperature TimeMinimum Recorded Temperature Time (TEMP_MIN_TIME [86.4]) shows
the date and time when the Temperature Minimum occurred.
Maximum Recorded Supply PressureMaximum Recorded Supply Pressure (SUPPLY_PRESS_MAX [86.5]) shows the
maximum supply pressure the instrument has experienced since installation.
Maximum Recorded Supply Pressure TimeMaximum Recorded Supply Pressure Time (SUPP_PRESS_MAX_TIME
[86.6]) shows the date and time when the Supply Pressure Maximum occurred.
Minimum Recorded Supply PressureMinimum Recorded Supply Pressure (SUPP_PRESS_MIN [86.7]) shows the
minimum supply pressure the instrument has experienced since installation.
Minimum Recorded Supply Pressure TimeMinimum Recorded Supply Pressure Time (SUPP_PRESS_MIN_TIME
[86.8]) shows the date and time when the Supply Pressure Minimum occurred.
Stroking the Digital Valve Controller Output

Field Communicator
TB > Device Diagnostic > Stroke Valve
Stroke Valve is used to confirm proper valve operation. Follow the prompts on the Field Communicator display to
select from the following: Done, Ramp Open, Ramp Closed, Ramp to Target, Step to Target, and Stop.
DoneSelect this if you are done. All ramping is stopped when DONE is selected.
Ramp Openramps the travel toward open at the rate of 1.0% per second of the ranged travel.
Ramp Closedramps the travel toward closed at the rate of 1.0% per second of the ranged travel.
Ramp to Targetramps the travel to the specified target at the rate of 1.0% per second of the ranged travel.
Step to Targetsteps the travel to the specified target.
Stopstops the command.
228
Instruction Manual
D103412X012
August 2012
Trend
Field Communicator
TB > Device Diagnostic > Trend
Trend chart of Setpoint (FINAL_VALUE.VALUE [13.2]), Travel (TRAVEL.VALUE [34.2]), and Pressure A
(PRESSURE_A.VALUE [36.2]).
Device Variables
Field Communicator
TB > Device Variables
All Block Modes

Block Mode: Target
The Target (TARGET [5.1]) mode is the mode requested by the user or host system. Generally, only one mode is
allowed to be set, and it must be a permitted mode as defined by the permitted attribute of the mode parameter.
Additionally, all cascade targets (Cas, Rcas) must have AUTO set.
Block Mode: Actual
This is the current mode of the block. The actual (ACTUAL [5.2]) mode may differ from the target mode due to
operating conditions of the block.
Note
Block Mode:Actual drops the AUTO bit for the cascade targets. For example, target mode might have Cas and Auto set, but actual
mode will only have Cas set.

The permitted (PERMITTED [5.3]) mode defines the modes allowed for the block. This is set by the user or host system
but is restricted by the instrument to modes supported by the instrument for the particular block. Any change request
to the Target or Normal attribute is checked against the permitted attribute to ensure the requested mode is
permitted. When setting the Permitted mode, there is no check against any of the other attributes (Normal or Target
modes). Therefore, the normal or target mode attributes may have a value that is not permitted because the
permitted attribute was modified after the Normal or Target mode was set. This will have no effect on the instrument
until the user attempts to modify the Target or Normal mode. At this time these attributes are tested against the
Permitted modes, thus the user cannot change the Normal or Target modes to what was formerly permitted.
Block Mode: Normal
The normal (NORMAL [5.4]) mode is the mode the block should be in during normal operating conditions. The normal
mode is set by the user or host system and can only be set to a permitted mode (see permitted mode). The user or
host system can compare the actual mode to the normal mode and, based on the results, determine if the block is
operating normally.
229
Instruction Manual
August 2012
D103412X012
AO Control - PreCharacterization
Setpoint
Setpoint (FINAL_VALUE.VALUE [13.2]) shows the value of the setpoint in % (percent) of ranged travel or pressure.
Setpoint is used for both travel and pressure control. This parameter will be written directly if the transducer block is in
MAN mode, or will be written automatically by the AO block if the transducer block is in AUTO mode.
Setpoint Status
Shows the Foundation Fieldbus status of Setpoint Value (FINAL_VALUE.STATUS [13.2]); Good, Uncertain, or Bad.
Travel (DeChar)
Travel (FINAL_POSITION_VALUE.VALUE [17.2]) shows the value of the travel in % (percent) of ranged travel. Travel
always represents how far the valve is open.
AO ControlPost Characterization
Travel Target
Travel target is the output from the characterization function.
Travel
Travel (TRAVEL.VALUE [34.2]) displays the actual position of the valve in percent (%) of calibrated travel.
Travel Status
Shows the Foundation Fieldbus status of Travel Value (TRAVEL.STATUS [34.1]); Good, Uncertain, or Bad.
DO Control
Setpoint(D)
Discrete Setpoint (SETPOINT_D.VALUE [32.2]) shows the value of the setpoint in discrete values.
0 = closed, 1 = open, 5, 10, 15... = setpoint in 5% units. This parameter will be written directly if the transducer block is
in MAN mode, or will be written automatically by the DO block if the transducer block is in AUTO mode.
Travel(D)
Travel (TRAVEL_D.VALUE [33.2]) shows the value of the setpoint in discrete values.
0 = closed, 1 = open, 5, 10, 15... = setpoint in 5% units.
Input Characterization (INPUT_CHAR [50]) defines the relationship between the setpoint specified by the output
function block and the desired valve position.
230
Instruction Manual
D103412X012
August 2012
Travel/Pressure State (TVL_PRESS.STATE [41.2]) indicates if the instrument is being used for travel control (position
control) or as an I/P (pressure control).
PD Inside Status
PD Inside Status shows the status of Performance Diagnostics.
Protection
Indicates the status of Protection.
Drive Signal
Drive Signal (DRIVE_SIGNAL [53]) indicates the drive signal, as a percentage of the maximum drive available, going to
the I/P converter from the printed wiring board. In most applications, the drive signal ranges between 50% and 75% of
the maximum drive signal.
Temperature
Temperature (TEMPERATURE [48]) displays the internal temperature of the instrument in either degrees Fahrenheit or
Celsius.
Cycle Counter
Cycle Counter (CYCLE_COUNT [73]) records the number of times the travel changes direction. The change in direction
must occur after the deadband has been exceeded before it can be counted as a cycle.
Travel Accumulator
Travel Accumulator (TRAVEL_ACCUM [72]) indicates the total change in travel, in percent of ranged travel. The
accumulator only increments when travel exceeds the deadband. Then the greatest amount of change in one
direction from the original reference point (after the deadband has been exceeded) will be added to the Travel
Accumulator.
Travel Count
Travel Count (TVL_COUNT [43.1]) is the Travel Sensor readback displayed in A/D counts.
231

August 2012
Instruction Manual
D103412X012
Pressures
Supply
Supply (SUPPLY_PRESSURE_VALUE [35.2]) shows the value of the supply pressure in psi, bar, kPa, inHg, inH2O, or
kg/cm2.
Pressure A
Pressure A (PRESSURE_A.VALUE [36.2]) shows the value of Output Pressure A in psi, bar, kPa, inHg, inH2O, or kg/cm2.
Pressure B
Pressure B (PRESSURE_B.VALUE [37.2]) shows the value of Output Pressure B in psi, bar, kPa, inHg, inH2O, or kg/cm2.
A Minus B
A Minus B (PRESSURE_DIFF.VALUE [38.2]) shows the value of the output pressure differential in psi, bar, kPa, inHg,
inH2O, or kg/cm2.
232
Instruction Manual
Maintenance and Troubleshooting
D103412X012
August 2012
Section 7 Maintenance and Troubleshooting7-7The DVC6200f digital valve controller enclosure is rated Type 4X and IP66, therefore periodic cleaning of internal
components is not required. If the DVC6200f is installed in an area where the exterior surfaces tend to get heavily
coated or layered with industrial or atmospheric contaminants, however, it is recommended that the vent (key 52) be
periodically inspected to ensure it is fully open. If the vent appears to be clogged, it can be removed, cleaned and
replaced. Lightly brush the exterior of the vent to remove contaminants and run a mild water/detergent solution
through the vent to ensure it is fully open. Allow the vent to dry before reinstalling.
WARNING
Personal injury or property damage can occur from cover failure due to overpressure. Ensure that the housing vent
opening is open and free of debris to prevent pressure buildup under the cover.
WARNING
WARNING
Avoid personal injury or property damage from sudden release of process pressure or bursting of parts. Before performing
any maintenance procedures on the DVC6200f digital valve controller:
Always wear protective clothing, gloves, and eyewear.
Do not remove the actuator from the valve while the valve is still pressurized.
Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure the
actuator cannot suddenly open or close the valve.
Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressure
from both sides of the valve.
Vent the pneumatic actuator loading pressure and relieve any actuator spring precompression.
Use lockout procedures to be sure that the above measures stay in effect while you work on the equipment.
Check with your process or safety engineer for any additional measures that must be taken to protect against process
media.
WARNING
When using natural gas as the supply medium, or for explosion proof applications, the following warnings also apply:
Remove electrical power before removing the housing cap. Personal injury or property damage from fire or explosion
may result if power is not disconnected before removing the cap.
Remove electrical power before disconnecting any of the pneumatic connections.
When disconnecting any of the pneumatic connections or any pressure retaining part, natural gas will seep from the
unit and any connected equipment into the surrounding atmosphere. Personal injury or property damage may result
233
Instruction Manual

August 2012
D103412X012
from fire or explosion if natural gas is used as the supply medium and appropriate preventive measures are not taken.
Preventive measures may include, but are not limited to, one or more of the following: ensuring adequate ventilation
and the removal of any ignition sources.
Ensure that the cover is correctly installed before putting this unit back into service. Failure to do so could result in
personal injury or property damage from fire or explosion.
CAUTION
When replacing components, use only components specified by the factory. Always use proper component replacement
techniques, as presented in this manual. Improper techniques or component selection may invalidate the approvals and
the product specifications, as indicated in table 11, and may also impair operations and the intended function of the
device.
Because of the diagnostic capability of the DVC6200f, predictive maintenance is available through the use of ValveLink
software. Using the digital valve controller, valve and instrument maintenance can be enhanced, thus avoiding
unnecessary maintenance. For information on using ValveLink software, refer to the ValveLink software online help.
Replacing the Magnetic Feedback Assembly

To remove the magnet assembly from the actuator stem, perform the following basic steps.
1. Make sure that the valve is isolated from the process.
2. Remove the instrument terminal box cover.
3. Disconnect the field wiring from the terminal board.
4. Shut off the instrument air supply.
5. Disconnect the pneumatic tubing and remove the DVC6200f or the DVC6215 from the actuator.
6. Remove the screws holding the magnet assembly to the connector arm.
When replacing the instrument, be sure to follow the mounting guidelines in the Installation section. Setup and
calibrate the instrument prior to returning to service.
Module Base Maintenance

The digital valve controller contains a module base consisting of the I/P converter, printed wiring board assembly, and
pneumatic relay. The module base may be easily replaced in the field without disconnecting field wiring or tubing.
Tools Required
Table 71 lists the tools required for maintaining the DVC6200f digital valve controller.
Table 71. Tools Required
Tool
Phillips Screwdriver
Hex key
Hex key
Hex key
Hex key
234
Size
5 mm
1.5 mm
2.5 mm
6 mm
Component
Relay, printed wiring board assembly, and cover screws
Terminal box screw
Terminal box cover screw
I/P converter screws
Module base screws
Instruction Manual
D103412X012

August 2012
Component Replacement
When replacing any of the components of the DVC6200f, the maintenance should be performed in an instrument
shop whenever possible. Make sure that the electrical wiring and pneumatic tubing is disconnected prior to
disassembling the instrument.
Removing the Module Base

Refer to figure 82 or 84 for key number locations.
WARNING
To avoid personal injury or equipment damage from bursting of parts, turn off the supply pressure to the digital valve
controller and bleed off any excess supply pressure before attempting to remove the module base assembly from the
housing.
1. Unscrew the four captive screws in the cover (key 43) and remove the cover from the module base (key 2).
2. Using a 6 mm hex socket wrench, loosen the threesocket head screws (key 38). These screws are captive in the
module base by retaining rings (key 154).
Note
The module base is linked to the housing by two cable assemblies. Disconnect these cable assemblies after you pull the module
base out of the housing.
CAUTION
To avoid affecting performance of the instrument, take care not to damage the module base seal or guide surface. Do not
bump or damage the bare connector pins on the PWB assembly. Damaging either the module base or guide surface may
result in material damage, which could compromise the instruments ability to maintain a pressure seal.
3. Pull the module base straight out of the housing (key 1). Once clear of the housing, swing the module base to the
side of the housing to gain access to the cable assemblies.
4. The digital valve controller has two cable assemblies, shown in figure 71, which connect the module base, via the
printed wiring board assembly, to the travel sensor and the terminal box. Disconnect these cable assemblies from
the printed wiring board assembly on the back of the module base.
235
Instruction Manual

August 2012
D103412X012
Figure 71. Printed Wiring Board Cable Connections

TERMINAL
BOX
MODULE BASE ASSEMBLY

PRINTED WIRING
BOARD
ASSEMBLY
HOUSING
CABLE
TO TERMINAL BOX
W99241
CABLE TO TRAVEL SENSOR
Replacing the Module Base

Refer to figure 82 or 84 for key number locations. Refer to figure 72 for a view of the back of the PWB assembly
submodule.
Figure 72. Back View of PWB Assembly SubModule
TERMINAL BOX
CONNECTOR
GE39341
PINS REMOVED FOR

CONNECTOR KEYING
TRAVEL SENSOR CONNECTOR
Note
To avoid affecting performance of the instrument, inspect the guide surface on the module and the corresponding seating area in
the housing before installing the module base assembly. These surfaces must be free of dust, dirt, scratches, and contamination.
Ensure the module base seal is in good condition. Do not reuse a damaged or worn seal.
236
Instruction Manual
D103412X012
August 2012
1. Ensure the module base seal (key 237) is properly installed in the housing (key 1). Ensure the Oring (key 12) is in
place on the module base assembly.
2. Connect the terminal box connector to the PWB assembly (key 50). Orientation of the connector is required.
3. Connect the travel sensor connector to the PWB assembly (key 50). Orientation of the connector is required.
4. Insert the module base (key 2) into the housing (key 1).
5. Install three socket head screws (key 38) in the module base into the housing. If not already installed, press three
retaining rings (key 154) into the module base. Evenly tighten the screws in a crisscross pattern to a final torque of
16 Nm (138 lbfin).
CAUTION
Personal injury, property damage, or disruption of process control can result if the cable assemblies/wiring are damaged
when attaching the cover to the module base assembly
Ensure that the cable assemblies/wiring are positioned in the cavity of the module base so they do not get compressed or
damaged when attaching the cover to the module base assembly in step 6.
6. Attach the cover (key 43) to the module base assembly.
Submodule Maintenance
The digital valve controller's module base contains the following submodules: I/P converter, PWB assembly, and
pneumatic relay. If problems occur, these submodules may be removed from the module base and replaced with new
submodules. After replacing a submodule, the module base may be put back into service.
CAUTION
Exercise care when performing maintenance on the module base. Reinstall the cover to protect the I/P converter and
gauges when servicing other submodules.
In order to maintain accuracy specifications, do not strike or drop the I/P converter during submodule maintenance.
I/P Converter
Refer to figure 82 or 84 for key number locations. The I/P converter (key 41) is located on the front of the module
base.
Note
After I/P converter submodule replacement, calibrate the digital valve controller to maintain accuracy specifications.
Replacing the I/P Filter

A screen in the supply port beneath the I/P converter serves as a secondary filter for the supply medium. To replace this
filter, perform the following procedure:
237
Instruction Manual

August 2012
D103412X012
1. Remove the I/P converter (key 41) and shroud (key 169) as described in the Removing the I/P Converter procedure.
2. Remove the screen (key 231) from the supply port.
3. Install a new screen in the supply port as shown in figure 73.
4. Inspect the Oring (key 39) in the I/P output port. if necessary, replace it.
5. Reinstall the I/P converter (key 41) and shroud (key 169) as described in the Replacing the I/P Converter procedure.
Figure 73. I/P Filter Location
ORING LOCATED IN I/P

CONVERTER OUTPUT PORT
SCREEN (FILTER) LOCATED IN I/P

CONVERTER SUPPLY PORT
W8072
Removing the I/P Converter

1. Remove the front cover (key 43), if not already removed.
2. Refer to figure 74. Using a 2.5 mm hex socket wrench, remove the four sockethead screws (key 23) that attach the
shroud (key 169) and I/P converter (key 41) to the module base (key 2).
3. Remove the shroud (key 169); then pull the I/P converter (key 41) straight out of the module base (key 2). Be
careful not to damage the two electrical leads that come out of the base of the I/P converter.
4. Ensure that the Oring (key 39) and screen (key 231) stay in the module base and do not come out with the I/P
converter (key 41).
Replacing the I/P Converter

1. Refer to figure 73. Inspect the condition of the Oring (key 39) and screen (key 231) in the module base (key 2).
Replace them, if necessary. Apply silicone lubricant to the Orings.
2. Ensure the two boots (key 210) shown in figure 74 are properly installed on the electrical leads.
238
Instruction Manual
D103412X012
August 2012
Figure 74. I/P Converter
I/P CONVERTER
(KEY 41)
W9328
SHROUD
(KEY 169)
SOCKETHEAD
SCREWS (4)
(KEY 23)
BOOTS
(KEY 210)
3. Install the I/P converter (key 41) straight into the module base (key 2), taking care that the two electrical leads feed
into the guides in the module base. These guides route the leads to the printed wiring board assembly submodule.
4. Install the shroud (key 169) over the I/P converter (key 41).
5. Install the four sockethead screws (key 23) and evenly tighten them in a crisscross pattern to a final torque of 1.6
Nm (14 lbfin).
6. After replacing the I/P converter, calibrate travel or perform touchup calibration to maintain accuracy
specifications.
Printed Wiring Board (PWB) Assembly

Refer to figure 82 or 84 for key number locations. The PWB assembly (key 50) is located on the back of the module
base assembly (key 2).
Note
The DVC6200f PWB assembly must be firmware revision 2.0 or later.
Note
If the PWB assembly submodule is replaced, calibrate and configure the digital valve controller to maintain accuracy specifications.
Removing the Printed Wiring Board Assembly

1.
2.
3.
4.
Separate the module base from the housing by performing the Removing the Module Base procedure.
Remove three screws (key 33).
Lift the PWB assembly (key 50) straight out of the module base (key 2).
Ensure that the Orings (key 40) remain in the pressure sensor bosses on the module base assembly (key 2) after the
PWB assembly (key 50) has been removed.
Replacing the Printed Wiring Board Assembly

1. Apply silicone lubricant to the pressure sensor Orings (key 40) and install them on the pressure sensor bosses in the
module base assembly.
239
Instruction Manual
August 2012
D103412X012
2. Properly orient the PWB assembly (key 50) as you install it into the module base. The two electrical leads from the
I/P converter (key 41) must guide into their receptacles in the PWB assembly and the pressure sensor bosses on the
module base must fit into their receptacles in the PWB assembly.
3. Push the PWB assembly (key 50) into its cavity in the module base.
4. Install and tighten three screws (key 33) to a torque of 1 Nm (10.1 lbfin).
5. Reassemble the module base to the housing by performing the Replacing the Module Base procedure.
6. Setup and calibrate the digital valve controller.
Note
Calibration is required for either Travel or Pressure Control after PWB Assembly replacement.
Note that only one calibration is needed, depending on control selection.
Pneumatic Relay
Refer to figure 82 or 84 for key number locations. The pneumatic relay (key 24) is located on the front of the module
base.
Note
After relay submodule replacement, calibrate the digital valve controller to maintain accuracy specifications.
Removing the Pneumatic Relay

1. Loosen the four screws that attach the relay (key 24) to the module base. These screws are captive in the relay.
2. Remove the relay.
Replacing the Pneumatic Relay

1. Visually inspect the holes in the module base to ensure they are clean and free of obstructions. If cleaning is
necessary, do not enlarge the holes.
2. Apply silicone lubricant to the relay seal and position it in the grooves on the bottom of the relay as shown in
figure 75. Press small seal retaining tabs into retaining slots to hold relay seal in place.
Figure 75. Pneumatic Relay Assembly
RELAY SEAL
W8074
240
Instruction Manual
D103412X012
August 2012
3. Position the relay (with shroud) on the module base. Tighten the four screws, in a crisscross pattern, to a final
torque of 2 Nm (20.7 lbfin).
4. Using the Field Communicator, verify that the value for Relay Type parameter matches the relay type installed.
5. After replacing the relay and verifying the relay type, calibrate travel or perform touchup calibration to maintain
accuracy specifications
Gauges, Pipe Plugs, or Tire Valves

Depending on the options ordered, the DVC6200f will be equipped with either gauges (key 47), pipe plugs (key 66), or
tire valves (key 67). Singleacting direct instruments will also have a screen (key 236, figure 83). These are located on
the top of the module base next to the relay.
Perform the following procedure to replace the gauges, tire valves, or pipe plugs. Refer to figure 82and 83 for key
number locations.
1. Remove the front cover (key 43).
2. Remove the gauge, pipe plug, or tire valve as follows:
For gauges (key 47), the flats are on the gauge case. Use a wrench on the flats of the gauge to remove the gauge from
the module base. For doubleacting instruments, to remove the supply gauge remove one of the output gauges.
For pipe plugs (key 66) and tire valves (key 67), use a wrench to remove these from the module base.
3. Apply zinc based anti-seize sealant (key 64) to the threads of the replacement gauges, pipe plugs, or tire valves.
4. Using a wrench, screw the gauges, pipe plugs, or tire valves into the module base.
Terminal Box
WARNING
Refer to the Maintenance WARNING at the beginning of this section.
Refer to figure 82 or 84 for key number locations.

The terminal box is located on the housing and contains the terminal strip assembly for field wiring connections.
Removing the Terminal Box

WARNING
To avoid personal injury or property damage caused by fire or explosion, remove power to the instrument before removing
the terminal box cover in an area which contains a potentially explosive atmosphere or has been classified as hazardous.
1. Loosen the set screw (key 58) in the cap (key 4) so that the cap can be unscrewed from the terminal box.
2. After removing the cap (key 4), note the location of field wiring connections and disconnect the field wiring from
the terminal box.
3. Separate the module base from the housing by performing the Removing the Module Base procedure.
241
Instruction Manual
August 2012
D103412X012
4. Disconnect the terminal box wiring connector from the PWB assembly (key 50).
5. Remove the screw (key 72). Pull the terminal box assembly straight out of the housing.
Replacing the Terminal Box

Note
Inspect all Orings for wear and replace as necessary.
1. Apply lubricant, silicone sealant to the Oring (key 34) and install the Oring over the stem of the terminal box.
2. Insert the terminal box assembly stem into the housing until it bottoms out. Position the terminal box assembly so
that the hole for the screw (key 72) in the terminal box aligns with the threaded hole in the housing. Install the
screw (key 72).
3. Connect the terminal box wiring connector to the PWB assembly (key 50).
4. Reassemble the module base to the housing by performing the Replacing the Module Base procedure.
5. Reconnect the field wiring as noted in step 2 in the Removing the Terminal Box procedure.
6. Apply lubricant, silicone sealant to the Oring (key 36) and install the Oring over the 25/8 inch threads of the
terminal box. Use of a tool is recommended to prevent cutting the Oring while installing it over the threads.
7. Apply lithium grease (key 63) to the 25/8 inch threads on the terminal box to prevent seizing or galling when the
cap is installed.
8. Screw the cap (key 4) onto the terminal box.
9. Install a set screw (key 58) into the cap (key 4). Loosen the cap (not more than 1 turn) to align the set screw over
one of the recesses in the terminal box. Tighten the set screw (key 58).
Stroking the Digital Valve Controller Output

After completing maintenance procedures, confirm proper valve operation by stroking the digital valve controller
output. Refer to page 228.
DVC6215 Feedback Unit

There are no replaceable parts on the DVC6215 feedback unit. Contact your Emerson Process Managment if a
replacement DVC6215 feedback unit is needed.
242
Instruction Manual
D103412X012
August 2012
Instrument Troubleshooting
What to Do First
When a problem occurs, check the following first:
Mounting
Is the feedback linkage connected correctly? See the beginning of this section.
Utility Connections
Are pneumatic connections correct? Are there any air leaks? See the Installation section.
Is the air supply pressure sufficient to drive the valve?
Is the digital valve controller correctly connected to the fieldbus? See the Installation section.
Is there power to the device? Is the terminal voltage between 9 and 32 volts? See the Installation section.
Is the segment terminated correctly? See host system documentation.
Is the host system connected to the segment? See host system documentation.
If communication or output difficulties are experienced with the instrument, refer to the troubleshooting information
provided in table 72.
Also see the Technical Support Checklist found on page 248.
243
Instruction Manual

August 2012
D103412X012
Table 72. Instrument Troubleshooting

Symptom
1 Instrument will not communicate.
Possible Cause
1a No power to device
1b Internal device wiring problems.
Action
1a1 Ensure device is connected to the segment (see
host system documentation).
1a2 Measure the terminal voltage. Terminal voltage
should be between 9 and 32 VDC.
1a3 Check to be sure device is drawing current. There
should be approximately 19 mA.
1b1 Verify connectors are plugged into the printed
wiring board correctly (see Printed Wiring Board
Assembly on page 239).
1b2 Check continuity of cable between terminal box
and printed wiring board. If necessary, replace the
terminal box assembly (see Replacing the Terminal Box
on page 242).
1b3 Check for damaged printed wiring board lands and
terminals. If necessary, replace the terminal box
assembly (see Replacing the Terminal Box on page
242).
1c Incompatible network settings

1d Defective printed wiring board (PWB) assembly.
1e Defective terminal box.
2 Device does not stay on segment.
3 A value cannot be written to a

parameter.
1f Defective Field Communicator or ValveLink

modem cable.
1g Fieldbus card defective or not compatible with PC.
2a Incorrect signal level.
1f If necessary, repair or replace cable.
2b Excess noise on segment.
2b1 Check integrity of wiring connections. Make sure

cable shield is grounded only at the control system.
2b2 Check for corrosion or moisture on terminals in
terminal box (refer to page 242 for terminal box
information).
2b3 Check for bad power supply.
2c Electronics failing.
2c. Replace printed wiring board assembly (see

Replacing the PWB Assembly on page 239).
3a Change Write Lock to Not Locked (refer to page 45).
3a Resource block parameter Write Lock may be set to

Locked.
3b If a transducer block parameter, the mode may be
incorrect or the parameter may be protected.
3c You have attempted to write a value that is outside

the valid range.
3.d Function block or in/out block mode may be
incorrect.
-Continued-
244
1c Change host parameters. Refer to host

documentation for procedure.
1dReplace printed wiring board (see Replacing the
PWB Assembly on page 239.
1e Check continuity from each screw terminal to the
corresponding PWB connector pin. If necessary, replace
the terminal box assembly (see Replacing the Terminal
Box on page 242).
1g Replace Fieldbus card.

2a1 Check that segment is properly terminated (see
host system documentation).
2a2 Wrong cable type or segment length too long. See
Site Planning Guide.
2a3 Bad power supply or conditioner.
3b1 Check table 414. If necessary change the

transducer block target mode to Manual.
3b2 Check table 414. If necessary change data
protection.
3c Check the range values listed for the parameter
(refer to the parameter tables in Section 4).
3.d. Confirm that block is in correct mode for writing to
any given parameter.
Instruction Manual
D103412X012
August 2012
Table 72. Instrument Troubleshooting (Continued)

Symptom
4 Function block actual mode does not
change with target mode.
Possible Cause
4a Resource block actual mode is Out of Service.
4b Transducer block actual mode is not Auto.
4c Schedules that define when function blocks execute

are not set correctly.
4d Configuration error
5 Input or Output Block does not go to

mode target
5a Resource block actual mode is Out of Service
5b Transducer block actual mode is not Auto.
5c Transducer has detected a hardware failure.
5d Wrong output block is active.
5e Output block is not licensed.
5f Schedules that define when function blocks execute

are not set correctly.
5g Configuration error.
Action
4a Change Resource block target mode to Auto (see
page 45, Resource Block Mode, or host system
documentation).
4b Change transducer block target mode to Auto (see
page 62, Transducer Block Mode or host system
documentation).
4c Set the schedules using host system or
configuration tool. All function blocks must be in a
schedule that is downloaded to the device.
4d Look for configuration error bit in BLOCK_ERR. By
default, all enumerature type parameters are initialized
to 0 (undefined). They must be configured before the
block can be put into service.
5a Change Resource block target mode to Auto (see
page 45, Resource Block Mode, or host system
documentation).
5b Change transducer block target mode to Auto (see
page 62, Transducer Block Mode or host system
documentation).
5c A bad status is passed to the block's READBACK or
FIELD_VAL parameter. See transducer section of
Detailed Setup for repair information.
5d Use Outblock Selection to select the desired output
block. The deselected block will have a bad status for
READBACK. This will keep it in IMAN mode when target
is other than OOS.
5e The Actual Block Mode (MODE_BLK.ACTUAL [5.2])
will remain out of service and the block cannot be
scheduled if the block has not bee licensed. Contact
your Emerson Process Management sales office to
upgrade product licensing.
5f Set the schedules using host system or configuration
tool. All function blocks must be in a schedule that is
downloaded to the device.
5g Look for configuration error bit in BLOCK_ERR. By
default, all enumerature type parameters are initialized
to 0 (undefined). They must be configured before the
block can be put into service.
6 Block dynamic parameters do not

update
6a Block actual mode is Out of Service
6a Change the block target mode to an operational

mode (see Appendix D, FOUNDATION fieldbus
Communication and host system documentation).
7 Transducer block Setpoint

(FINAL_VALUE [13]) is not being
automatically updated from the AO
block.
7a Transducer block mode in not Auto.
7a Change transducer block mode to Auto.
7b AO block is not active.
7b Change Outblock Selection to AO Control.
8 Transducer block setpoint

Setpoint(D) (SETPOINT_D [32]) is not
being automatically updated from the
DO block.
8a Transducer block mode is not Auto.
8a Change transducer block mode to Auto.
8b DO block is not active.
8.b Change Outblock Selection to DO Control.
9 Valve does not move when the set

point is changed
9a A function block actual mode is Out of Service or

Transducer Block Actual mode is Out of Service or
Manual.
9a1 Change the target mode to an operational mode

(see Appendix D, FOUNDATION fieldbus Communication
and host system documentation).
9a2 Verify that the correct block (AO or DO) is
configured in Feature Select in the resource block. Only
the selected out block is able to set the transducer
setpoint and move the valve.
9b Pneumatic connections are incorrect or supply

pressure is incorrect
9b Check pneumatic connections and supply pressure.

Be sure supply pressure regulator is set correctly (see
Pneumatic Connections on page 26).
-Continued-
245
Instruction Manual

August 2012
D103412X012

Symptom
Possible Cause
Action
9c Instrument is in fault state.
10 Valve does not stroke from 0 to

100% with set point change
11 Deviation between set point and

actual valve position remains.
12 The valve cycles, does not stay on

set point.
13 Valve responds too slowly.
9c Set Clear FState to Clear (Refer to Fault State on

page 47 of the Detailed Setup / Blocks Section, or host
system documentation).
9d The valve has failed.
9d Apply a pneumatic pressure to the valve actuator
and check valve action.
9e The I/P converter or relay has failed.
9e Replace the I/P converter or relay (see Replacing the
I/P Converter on page 238).
10a Insufficient supply pressure or leak in pneumatic
10a Check supply pressure and supply pressure
connections.
regulator setting. Check for leaks around pneumatic
connections.
10b Setpoint may be limited.
10b Check the AO Block values of SP_HI_LIMIT and
SP_LO_LIMIT (see page 122 or host system
documentation).
11aDigital valve controller output is in cutoff.
11a Check values for Travel Cutoff High and Travel
Cutoff Low (see page 67 or host system
documentation).
11b Digital valve controller is not calibrated correctly
11b Perform Auto or Manual Travel Calibration (Travel
Calibration on page 214.)
11c Incorrect turning. Tuning that is too conservative will 11c Perform Stabilizing/Optimize Valve Response
result in excess error.
procedure toadjust tuning and stabilize/optimize
valve response (see Stabilize/Optimize on page 64).
12a Large amount of packing friction.
12a1 Perform Stabilizing/Optimize Valve Response
procedure toadjust tuning and stabilize/optimize
valve response (see Stabilize/Optimize on page 64).
12a2 Use a larger size actuator.
13a Insufficient instrument gain.
13b I/P converter input filter clogged or air blockage in

I/P ass'y nozzle block.
13 Valve responds too slowly.
13c Oring(s) between I/P converter missing or hard and

flattened losing seal.
13d I/P ass'y out of spec.
13e Defective gasket.
13f Defective relay.
13f Remove relay, inspect for missing Belleville washer,

missing valve spring, missing valve plug. Inspect lip
under top Oring for breakage due to relay removal.
Inspect Orings and replace if hard or damaged.
Replace parts or relay if I/P ass'y good and air passages
not blocked (see Replacing the Pneumatic Relay on
page 240).
13g If responds slowly only upon air demand, there may

be a restriction in the air line, the supply run may be
excessively long, or the supply regulator may be
defective or capacity not large enough.
13g1 Check supply line to ensure it is not clogged or

damaged. Replace if necessary.
13g2 If supply run is excessively long, a volume tank
may need to be installed on the the supply side of the
pressure regulator
13g3 Replace supply regulator
-Continued-
246
13a Perform Stabilize/Optimize Valve Response

procedure toadjust tuning and stabilize valve
response (see Stabilize/Optimize on page 64).
13b1 Replace I/P converter filter (see Replacing the I/P
Filter on page 237).
13b2 Replace I/P converter (see Replacing the I/P
Converter on page 238).
13c Replace Oring(s) (refer to the I/P Converter section
on page 237).
13d I/P ass'y nozzle may have been adjusted.
Verify drive signal (55% to 80%) (refer to Elect and
Config on page 69 or host system documentation).
Replace I/P ass'y if drive signal is continuously high or
low (see Replacing the I/P Converter on page 238).
13e Check gasket for closed holes, excessive
deformation due to overtightening or oozing. If
necessary, replace gasket (see the beginning of this
section).
Instruction Manual
D103412X012
August 2012

Symptom
14 Instrument will not calibrate, has
sluggish performance or oscillates.
15 Instrument will not calibrate.
Possible Cause
14a Replace the housing (key 1)
14b Travel feedback is out of accepted range
14c Cables not plugged into PWB correctly.
14b Check the mounting. Ensure the correcting

mounting kit has been selected and the magnetic array
is properly installed.
14c Inspect connections and correct.
14d Configuration errors.
14d Verify configuration. Use Device Setup on page 40.
14e Restricted pneumatic passages in I/P converter
14e Check screen in I/P converter supply port of the

module base. Replace if necessary. If passages in I/P
converter restricted, replace I/P converter (see
Replacing the I/P Converter on page 238).
14f Oring(s) between I/P converter ass'y missing or hard 14f Replace Oring(s) (refer to the I/P Converter section
and flattened losing seal.
on page 237).
14g I/P converter ass'y damaged/corroded/clogged.
14g Check for bent flapper, open coil (continuity),
contamination, staining, or dirty air supply. Coil
resistance should be between 1680 1860 ohms.
Replace I/P ass'y if damaged, corroded, clogged, or
open coil (see Replacing the I/P Converter on page 238).
14h I/P converter ass'y out of spec.
14h I/P converter ass'y nozzle may have been adjusted.
Verify drive signal (55 to 80% for doubleacting; 60 to
85% for singleacting) with the valve off the stops.
Replace I/P converter ass'y if drive signal is continuously
high or low (see Replacing the I/P Converter on page
238).
14i Defective module base seal.
14i Check module base seal for condition and position.
If necessary, replace seal. Refer to Module Base
Maintenance on page 234.
14j Defective relay.
14j Depress relay beam at adjustment location in
shroud, look for increase in output pressure. Remove
relay, inspect relay seal. Replace relay seal or relay if I/P
converter ass'y good and air passages not blocked
(refer to Replacing the Pneumatic Relay on page 240).
Check relay adjustment (refer to page 215).
14k Defective 67CFR regulator, supply pressure gauge
14k Replace 67CFR regulator.
jumps around.
15a Configuration errors.
15a Verify configuration.
15b Magnet assembly is not correctly installed.
15c Cables not plugged into PWB correctly.

16 ValveLink diagnostic tests provide
erroneous results.
Action
14a Travel sensor failed.
16b Pressure sensor Oring(s) missing.
16a Replace PWB (see Replacing the PWB Assembly on

page 239).
16b Replace Oring(s).
17 Cannot perform advanced

diagnostics.
17a Instrument does not have proper tiering.
17a Upgrade tiering.
18 A PlantWeb alert is active, but not

reported (broadcast) automatically.
18a PlantWeb alerts in firmware 1.5 and higher are

modebased. Transducer block mode may be in MAN or
OOS.
19a Battery pack not charged.
18a Check transducer block mode. Change to AUTO if

appropriate.
19 Field Communicator does not turn

on.
16a Defective pressure sensor(s).
15b Check the mounting. Ensure the correcting

mounting kit has been selected and the magnetic array
is properly installed.
15c Inspect connections and correct.
19a Charge battery pack.

Note: Battery pack can be charged while attached to the
Field communicator or separately. The Field
Communicator is fully operable while the battery pack is
charging. Do not attempt to charge the battery pack in
a hazardous area.
247
Instruction Manual

August 2012
D103412X012
Technical Support Checklist

Have the following information available prior to contacting your Emerson Process Management sales office for
support.
Reference
1. Instrument serial number as read from nameplate _________________________________________
2. What is the firmware version of the DVC6200f? _________________
3. What is the hardware version of the DVC6200f? ________________
4. What is the Diagnostic Tier of the DVC6200f? FD___ AD___ PD___
5. What is the Control Tier of the DVC6200f? SC___ FL___ FC___
6. What is the address of the DVC6200f? ________________________
Mode and Status
7. What are the DVC6200f Block Modes?
Actual Modes:
Resource Block _____ Transducer Block_____ Analog Output Block _____
Target Modes:
Permitted Modes:
8. What is the status of the individual function blocks?

Operational
9. Does the digital valve controller respond to the control signal? Yes _________ No _________
If No, describe
10. Is it on Travel or Pressure control?
11. What are the following parameter readings?
Setpoint _________
Drive Signal _________%
Supply Pressure _________
Pressure A _________
Pressure B _________
Travel Target _________%
Travel _________%
Pressure B _________
12. What is the safe position of the valve? Fail Closed ____ Fail Open ____
Interface and Diagnostic Tools
13. What interface and diagnostic tools are available?___________________________________
14. Provide any available supporting documentation, such as Status Monitor, Detailed Setup, any alert readings.
Mounting
Reference
1. Actuator application: sliding-stem? _________ Rotary? _________
2. Which digital valve controller do you have? DVC6200f _________ DVC6205f/DVC6215 _________
3. What Make, Brand, Style, Size, etc. actuator is the DVC6200f mounted on? _________________________
Operational
4. What is the full travel of the valve?__________________________________
5. What is the Mounting Kit part number? ______________________________
Other
6. If mounting kits are made by LBP/Customer, please provide pictures of installation.
248
Instruction Manual
Parts
D103412X012
August 2012
Section 8 Parts8-8Parts Ordering

Whenever corresponding with your Emerson Process Management sales office about this equipment, always mention
the controller serial number. When ordering replacement parts, refer to the 11character part number of each
required part as found in the following parts list. Part numbers are shown for kits and recommended spares only. For
part numbers not shown, contact your Emerson Process Management sales office.
WARNING
Use only genuine Fisher replacement parts. Components that are not supplied by Emerson Process Management should
not, under any circumstances, be used in any Fisher instrument. Use of components not supplied by Emerson Process
Management may void your warranty, might adversely affect the performance of the instrument, and could cause personal
injury and property damage.
Parts Kits
Kit
Description
1*
Elastomer Spare Parts Kit (kit contains parts to

service one digital valve controller)
Standard
Extreme Temperature option
(fluorosilicone elastomers)
Part Number
Description
6*
Spare Module Base Assembly Kit

[kit contains module base (key 2); drive screws, qty. 2,
(key 11); shield/label (key 19); hex socket cap screw, qty. 3,
(key 38); self tapping screw, qty. 2 (key 49); pipe plug, qty. 3
(key 61); retaining ring, qty. 3 (key 154); screen (key 236);
and flame arrestors, qty. 3 (key 243)]
Aluminum
GE18654X012
Stainless Steel
GE18654X022
7*
Spare Housing Assembly Kit,

[kit contains housing (key 1); vent assembly (key 52);
seal (only included in Housing A kits) (key 288);
seal (key 237); Oring (key 34); Oring (only used
with integrally mounted regulator) (key 5)]
19B5402X012
19B5402X022
2*
Small Hardware Spare Parts Kit (kit contains parts

to service one digital valve controller)
19B5403X012
3*
Seal Screen Kit

[kit contains 25 seal screens (key 231)
and 25 Orings (key 39)]
Standard and Extreme Temperature option
4*
Kit
14B5072X182
Aluminum
Housing A (used for GX actuator)
Standard (nitrile elastomers)
Housing B (used for all actuators except GX)
Terminal Box Kit

Aluminum
Standard
Standard, Natural Gas approved
Natural Gas Approved
Stainless Steel, fluorosilicone elastomers
5*
I/P Converter Kit
Standard
For Extreme Temperature option

*Recommended spare parts
GE44077X012
GE44081X012
GE44078X012
Stainless Steel
GE44082X012
GE44080X012
38B6041X152
38B6041X132

8*
Spare I/P Shroud Kit

[kit contains shroud (key 169) and
hex socket cap screw, qty. 4 (key 23)]
Part Number
GE48798X032
GE48798X042
GE48798X072
GE48798X082
GE48798X092
GE48798X102
GE29183X012
249
Instruction Manual
Parts
August 2012
Kit
9*
Description
Part Number
Remote Mount Feedback Unit Kit (see figure 85)

[remote housing assembly (key25); hex socket set
screw (key 58); 1/2 NPT pipe plug (key 62); wire retainer, qty 2
(key 131); terminal cover (key 255); o-ring (key 256); gasket
(Housing A only, used for GX actuator) (key 287); seal
(Housing A only, used for GX actuator) (key 288)
10*
D103412X012
GE46670X012
GE40178X012
Feedback Array Kit

[kit contains feedback array and machine screws, qty. 2 and
washers, qty. 2; 210 mm (8-1/4 inch) kit also contains insert]
7 mm (1/4-inch)
Aluminum
19 mm (3/4-inch)
Aluminum
Stainless steel
25 mm (1-inch)
Aluminum
Stainless steel
38 mm (1-1/2 inch)
Aluminum
Stainless steel
50 mm (2-inch)
Aluminum
Stainless steel
100 mm (4-inch)
Aluminum
Stainless steel
210 mm (8-1/4 inch)
Aluminum
Stainless steel
GE09169X022
GE09169X032
GE09169X072
GE09169X012
GE09169X082
GE09169X042
GE09169X092
GE09170X012
GE09169X102
GE09169X062
GE09169X132
Screw, hex head (4 reqd) (DVC6205f only)

Screw, hex head (4 reqd) (DVC6205f only)
Spacer (4 reqd) (DVC6205f only)
Standoff (2 reqd) (DVC6205f only)
Screen(7)
Gasket, Housing A only (used for GX actuator) (DVC6200f only)
Seal, Housing A only (used for GX actuator) (DVC6200f only)
Common Parts
(see figure 82, 83, and 84)
DVC6200f and DVC6205f
16*
29
33
38
43*
48
49
61
63
64
65
154
236
237
Note
Part numbers are shown for recommended spares only. For part
numbers not shown, contact your Emerson Process Management sales
office.
Parts with footnote numbers are available in parts kits; see footnote
information at the bottom of the page.
Description
Description
248
249
250
267
271
287
288
GE43790X012
GE09169X112
Parts List
Key
Key
Part Number
Housing (see figure 82 and 84)
Oring(1) (3 req'd)
Warning label, for use only with LCIE hazardous area
classifications
Mach Screw, pan hd, SST(2) (3 req'd)
Cap Screw, hex socket, SST(2)(6) (3 req'd)
Cover Assembly (includes cover screws)
Standard
38B9580X022
Extreme temperature option
38B9580X032
Nameplate
Screw, self tapping (2 req'd)(6)
Pipe Plug, hex socket(6)
Housing A with relay C (2 req'd ) (used for GX actuator)
Housing A with relay B (1 req'd) (used for GX actuator)
Housing B with relay B and C (1 req'd)
(used for all actuators except GX)
Not required for relay A
Lithium grease (not furnished with the instrument)
Zinc based antiseize compound (not furnished with the
instrument)
Lubricant, silicone sealant (not furnished with the instrument)
Retaining Ring(2) (3 req'd)
Screen (required for relay B and C only)(7)
Module Base Seal(1)
Module Base
(see figure 82 and 84)
2
11
12
19
61
243
Module Base(6)
Drive Screw(6) (2 req'd)
Oring(1)
Label, Shield Assembly(6)
Pipe Plug, hex socket(6) (3 req'd)
Slotted Pin (flame arrestor)(6) (3 req'd)

1
11
20
52
74
250
Housing(7)
Drive Screw (2 req'd) (DVC6205f only)
Shield (DVC6205f only)
Vent, plastic(2)
Mounting Bracket (DVC6205f only)
*Recommended spare
1. Available in the Elastomer Spare Parts Kit
2. Available in the Small Hardware Spare Parts Kit
6. Available in the Spare Module Base Assembly Kit
7. Available in the Spare Housing Assembly Kit
Instruction Manual
Parts
D103412X012
Key
Description
August 2012
Part Number
Figure 81. Terminal Box of Natural Gas Certified

FIELDVUE DVC6200f Digital Valve Controller
WIRING CONNECTOR
I/P Converter Assembly

GASBLOCKING
PRESSFIT ADAPTOR

23
39*
41
169
210*
231*
Cap Screw, hex socket, SST(2)(8) (4 req'd)

Oring(1)(3)(5)
I/P Converter(5)
Shroud(5)(8) (not shown, see figure 74)
Boot, nitrile(1)(5) (2 req'd) (see figure 74)
Seal Screen(1)(3)(5)
Relay (see figure 82 and 84)

Key
24* Relay Assembly, (includes shroud, relay seal, mounting screws)

Standard Bleed
Single/acting direct (relay C)
Singleacting reverse (relay B)
Singleacting direct (relay C)
Doubleacting (relay A)
Low Bleed
Housing B (used for all actuators except G)
W99231
38B5786X182
38B5786X172
38B5786X132
38B5786X052
38B5786X092
38B5786X202
38B5786X192
38B5786X152
38B5786X072
38B5786X112
Extreme Temperature option (fluorosilicone elastomers)

Standard Bleed
38B5786X142
38B5786X032
38B5786X102
Low Bleed
38B5786X162
38B5786X082
38B5786X122
Description
Part Number
Loop Connections Terminal Box

4
34*
36*
58
72
164
Terminal Box Cap

Oring(1)(4)
Oring(1)(4)
Set Screw, hex socket, SST(2)
Cap Screw, hex socket, SST(2)
Terminal Box Assembly
Feedback Connections Terminal

Box (see figure 84)
DVC6205f
4
34*
36*
58
62
64
262
263*
264
Terminal Box Cap

Oring(1)(4)
Oring(1)(4)
Set Screw, hex socket, SST(2)
Pipe Plug, hex hd, SST
Antiseize compound (not furnished with the instrument)
Adapter
O-ring
Standard
1F463606992
Extreme temperature option, (fluorosilicone)
1F4636X0092
Terminal Box Assembly, remote
*Recommended spare
1. Available in the Elastomer Spare Parts Kit
2. Available in the Small Hardware Spare Parts Kit
3. Available in the Seal Screen Kit
4. Available in the Terminal Box Kit
5. Available in the I/P Converter Kit
8. Available in the Spare Shroud Kit
251
Instruction Manual
Parts
August 2012
Key
Description
PWB Assembly
D103412X012
Key
Description
Part Number
Pressure Gauges, Pipe Plugs, or

Tire Valve Assemblies
(see figure 83)
Note
Contact your Emerson Process Management sales office for PWB
Assembly FS numbers.
50*
252
PWB Assembly
Standard Control
Fieldbus Diagnostics
Advanced Diagnostics
Performance DIagnostic
Fieldbus Control
Performance Diagnostics
Fieldbus Logic
Performance Diagnostics
47*
Pressure Gauge, nickelplated brass case, brass connection

Doubleacting (3 req'd); Singleacting (2 req'd)
PSI/MPA Gauge Scale
To 60 PSI, 0.4 MPa
18B7713X042
To 160 PSI, 1.1 MPa
18B7713X022
PSI/bar Gauge Scale
To 60 PSI, 4 bar
18B7713X032
To 160 PSI, 11 bar
18B7713X012
PSI/KG/CM2 Gauge Scale
To 60 PSI, 4 KG/CM2
18B7713X072
To 160 PSI, 11 KG/CM2
18B7713X082
66
Pipe Plug, hex hd

For doubleacting and singleacting direct w/gauges
(none req'd)
For singleacting reverse w/gauges (1 req'd)
For all units w/o gauges (3 req'd)
Tire Valve, used with Tire Valve Option only
Doubleacting (3 req'd); Singleacting (2 req'd)
67
*Recommended spare parts
Instruction Manual
Parts
D103412X012
August 2012
Figure 82. FIELDVUE DVC6200f Digital Valve Controller

Housing Assembly
HOUSING ABACK VIEW

(USED FOR GX ACTUATOR)
DOUBLEACTING
DIRECTACTING
HOUSING BBACK VIEW

(USED FOR ALL
ACTUATORS EXCEPT GX)
REVERSEACTING
APPLY LUBRICANT, SEALANT, OR THREAD LOCK

APPLY LUBRICANT ON ALL O-RINGS UNLESS OTHERWISE SPECIFIED
GE40185 sheet 1 of 3
253
Instruction Manual
Parts
August 2012
D103412X012
Figure 82. FIELDVUE DVC6200f Digital Valve Controller Housing Assembly (continued)
SECTION C-C
SCALE 2 : 1
SECTION A-A
SECTION E-E
SCALE 2 : 1

SECTION F-F
SCALE 2 : 1
Figure 83. Gauge Configuration
DOUBLEACTING
DIRECTACTING
FOR PIPE PLUG OPTION REPLACE 47 WITH 66

FOR TIRE VALVE OPTION REPLACE 47 WITH 67
254
REVERSEACTING
Instruction Manual
Parts
D103412X012
August 2012
Figure 84. FIELDVUE DVC6205f Base Unit Housing Assembly
SECTION B-B
SECTION A-A
SECTION H-H

GE40181
255
Instruction Manual
Parts
August 2012
D103412X012
Figure 84. FIELDVUE DVC6205f Base Unit Housing Assembly (continued)
SECTION C-C
SCALE 2 : 1
SECTION E-E
SCALE 2 : 1
DOUBLEACTING
DOUBLEACTING SHOWN
DIRECTACTING

GE40181
256
REVERSEACTING
Instruction Manual
Parts
D103412X012
August 2012
Figure 84. FIELDVUE DVC6205f Base Unit Housing Assembly (continued)
WALL MOUNTING
PIPE MOUNTING

GE40181
257
Instruction Manual
Parts
August 2012
D103412X012
Figure 85. FIELDVUE DVC6215 Remote Feedback Assembly
SECTION A-A
PARTS NOT SHOWN: 158
GE46670-B
HOUSING A
(USED FOR GX ACTUATOR)
SECTION A-A
PARTS NOT SHOWN: 158

GE40178-B
HOUSING B
(USED FOR ALL ACTUATORS EXCEPT GX)
258
Instruction Manual
Principle of Operation
D103412X012
August 2012
Appendix A Principle of OperationAA

Digital Valve Controller Operation
The DVC6200f digital valve controller has a single module base that may be easily replaced in the field without
disconnecting field wiring or tubing. The master module contains the following submodules: currenttopneumatic
(I/P) converter, printed wiring board assembly, and pneumatic relay. The relay position is detected by sensing the
magnet on the relay beam via a detector on the printed wiring board. This sensor is used for the minor loop feedback
(MLFB) reading. The master module can be rebuilt by replacing the submodules. See figures A1 and A2.
Figure A1. FIELDVUE DVC6200f Digital Valve Controller Block Diagram
DIGITAL
SETPOINT
932 VOLT
FIELDBUS
VALVE TRAVEL FEEDBACK
PRINTED
WIRING BOARD
DRIVE
SIGNAL
AUXILIARY
TERMINALS
OUTPUT A
I/P
CONVERTER
TERMINAL BOX
PNEUMATIC
RELAY
SUPPLY
PRESSURE
OUTPUT B
VALVE AND
ACTUATOR
VENT
E1376
The DVC6200f digital valve controller is a buspowered instrument that provides a control valve position in response
to a digital setpoint from the control room. The following describes a direct acting DVC6200f digital valve controller
mounted on a sliding-stem piston actuator, where the valve is closed with zero power to the instrument.
The setpoint is routed into the terminal box through a single pair of wires and then to the printed wiring board
assembly submodule where it is read by the microprocessor, processed by a digital algorithm, and converted into an
analog I/P drive signal.
259
Instruction Manual
Principle of Operation
August 2012
D103412X012
As the setpoint increases, the drive signal to the I/P converter increases, increasing the I/P output pressure. The I/P
output pressure is routed to the pneumatic relay submodule. The relay is also connected to supply pressure and
amplifies the small pneumatic signal from the I/P converter. The relay accepts the amplified pneumatic signal and
provides two output pressures. With relay A, an increasing setpoint will produce increasing pressure at output A and
decreasing pressure at output B. With relay B an increasing setpoint will produce decreasing pressure at output B
(output A is not available). With relay C an increasing setpoint will produce an increasing pressure on output A (output
B is not available). The output A pressure is used for doubleacting and singleacting direct applications. The output B
pressure is used for doubleacting and singleacting reverse applications.
Figure A2. FIELDVUE DVC6200f Digital Valve Controller Assembly
HOUSING
PNEUMATIC
RELAY
GAUGES
COVER
TERMINAL BOX
WITH COVER
PRINTED WIRING
BOARD ASSEMBLY
MODULE BASE ASSEMBLY
I/P CONVERTER
W99251
As shown in figure A1, the increased output A pressure causes the actuator stem to move upward. The stem position
is sensed by the travel sensor. The stem continues to move upward until the correct stem position is attained. At this
point the printed wiring board assembly stabilizes the I/P drive signal. This prevents any further increase in the
pneumatic signal from the I/P converter.
As the digital setpoint decreases, the drive signal to the I/P converter submodule decreases, decreasing the I/P output
pressure. The pneumatic relay decreases the output A pressure and increases the output B pressure. The stem moves
downward until the correct position is attained. At this point the printed wiring board assembly stabilizes the I/P drive
signal. This prevents any decrease in the pneumatic signal from the I/P converter.
260
Instruction Manual
D103412X012
August 2012
Appendix B Field Communicator Menu StructureBB

This section contains the Field Communicator menu trees for the transducer block and the resource block. It also
contains Fast Key Sequence tables with coordinates to help locate the function/variable on the appropriate menu tree.
261
Instruction Manual

August 2012
D103412X012
Transducer Block (TB) Menu Structure

Parameter Label
Menu Structure
A Minus B
TB > Device Variables > Pressures > A Minus B
Actual Travel
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Actual Travel
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Fail Action
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Manufacturer
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Model Number
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Serial Number
Actuator Size
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Size
Actuator Style
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Style
Advise Active
TB > Configure/Setup > Detailed Setup > Alert Handling > Simulate Active Alerts > Advise Active
Advise Enable
TB > Configure/Setup > Detailed Setup > Alerts > PlantWeb Alert Enable > Advise Enable
Advise Suppress
TB > Configure/Setup > Detailed Setup > Alerts > PlantWeb Alert Reporting > Advise Suppress
Air
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Air
Alert Conditions
TB > Device Diagnostics > Alert Conditions
Alert Key
TB > Configure/Setup > Detailed Setup > Alerts > Configuration Alerts > Alert Key
Area Units
TB > Configure/Setup > Detailed Setup > Instrument > Area Units
Block Configuration Error
TB > Device Diagnostics > Status > Block Error > Block Configuration Error
Blocks Set to Defaults Alert
TB > Configure/Setup > Detailed Setup > Alerts > Configuration Alerts > Blocks Set to Defaults > Block Set to Defaults Alert
Blocks Set to Defaults Alert

Enable
TB > Configure/Setup > Detailed Setup > Alerts > Configuration Alerts > Blocks Set to Defaults > Block Set to Defaults Alert Enable
Calibration Date
TB > Configure/Setup > Detailed Setup > Instrument > Calibration Date
TB > Configure/Setup > Detailed Setup > Instrument > Calibration Location
Calibration Person
TB > Configure/Setup > Detailed Setup > Instrument > Calibration Person
TB > Configure/Setup > Detailed Setup > Response Control > Custom Characterization Table
Cycle Counter
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts > Cycle Counter > Cycle Counter
TB > Device Variables > Cycle Counter
Cycle Counter Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts > Cycle Counter > Cycle Counter Alert
Cycle Counter Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts > Cycle Counter > Cycle Counter Alert Enable
Cycle Counter Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts > Cycle Counter > Cycle Counter Alert Point
Cycle Counter Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts > Cycle Counter > Cycle Counter Deadband
TB > Device Diagnostics > Status > Block Error > Device Needs Maintenance Now
Drive Current
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Drive Current > Drive Current
Drive Current Alert
TB > Device Diagnostics > Status > Self Test Status > Drive Current Alert
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Drive Current > Drive Current Alert
Drive Current Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Drive Current > Drive Current Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Drive Current > Drive Current Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Drive Current > Drive Current Alert Time
Drive Current Manual Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Drive Current > Drive Current Manual Recovery
Drive Current Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Drive Current > Drive Current Shutdown
Drive Signal
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Drive Signal > Drive Signal
TB > Device Variables > Drive Signal
Drive Signal Alert
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Drive Signal > Drive Signal Alert
Drive Signal Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Drive Signal > Drive Signal Alert Enable
Effective Area
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Effective Area
Failed Active
TB > Configure/Setup > Detailed Setup > Alert Handling > Simulate Active Alerts > Failed Active
Failed Enable
TB > Configure/Setup > Detailed Setup > Alerts > PlantWeb Alert Enable > Failed Enable
Failed Suppress
TB > Configure/Setup > Detailed Setup > Alerts > PlantWeb Alert Reporting > Failed Suppress
Feedback Connection
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Feedback Connection
Flow Direction
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Flow Direction
Flow Tends To
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Flow Tends To
I/O Processor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > I/O Processor Alert
I/O Processor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > I/O Processor Alert Enable
I/O Processor Man Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > I/O Processor Man Recovery
I/O Processor Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > I/O Processor Shutdown
Inlet Pressure
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Inlet Pressure
Continued
262
Instruction Manual
D103412X012
August 2012
Transducer Block (TB) Menu Structure (Continued)

Parameter Label
Menu Structure
TB > Configure/Setup > Detailed Setup > Response Control > Input Characterization
TB > Device Variables > Input Characterization
Integrator Limited Hi
TB > Device Diagnostics > Status > Self Test Status > Integrator Limited Hi
Integrator Limited Lo
TB > Device Diagnostics > Status > Self Test Status > Integrator Limited Lo
Integrator Suspended
TB > Device Diagnostics > Status > Self Test Status > Integrator Suspended
IOP Failure
TB > Device Diagnostics > Status > Self Test Status > IOP Failure
Last Calibration Type
TB > Configure/Setup > Detailed Setup > Instrument > Last Calibration Type
Leak Class
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Leak Class
Length Units
TB > Configure/Setup > Detailed Setup > Instrument > Length Units
Lever Arm Length
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Lever Arm Length
Lever Style
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Lever Style
Lost Static Data
TB > Device Diagnostics > Status > Block Error > Lost Static Data
Lower Bench Set
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Lower Bench Set
MAI Channel 1
TB > Configure/Setup > Detailed Setup > MAI Channel Map > MAI Channel 1
MAI Channel 2
MAI Channel 3
MAI Channel 4
MAI Channel 5
MAI Channel 6
MAI Channel 7
MAI Channel 8
Maint Active
TB > Configure/Setup > Detailed Setup > Alert Handling > Simulate Active Alerts > Maint Active
Maintenance Enable
TB > Configure/Setup > Detailed Setup > Alerts > PlantWeb Alert Enable > Maintenance Enable
TB > Configure/Setup > Detailed Setup > Alerts > PlantWeb Alert Reporting > Maintenance Suppress
Maximum Recorded Supply

Pressure
TB > Device Diagnostics > Device Record > Maximum Recorded Supply Pressure
Maximum Recorded Supply

Pressure Time
TB > Device Diagnostics > Device Record > Maximum Recorded Supply Pressure Time
Maximum Recorded
Temperature
TB > Device Diagnostics > Device Record > Maximum Recorded Temperature
Maximum Recorded
Temperature Time
TB > Device Diagnostics > Device Record > Maximum Recorded Temperature Time
Maximum Supply Pressure
TB > Configure/Setup > Detailed Setup > Instrument > Maximum Supply Pressure
Minimum Recorded Supply

Pressure
TB > Device Diagnostics > Device Record > Minimum Recorded Supply Pressure
Minimum Recorded Supply

Pressure Time
TB > Device Diagnostics > Device Record > Minimum Recorded Supply Pressure Time
Minimum Recorded
Temperature
TB > Device Diagnostics > Device Record > Minimum Recorded Temperature
Minimum Recorded
Temperature Time
TB > Device Diagnostics > Device Record > Minimum Recorded Temperature Time
MLFB Error
TB > Device Diagnostics > Status > Self Test Status > MLFB Error
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Nominal Supply Pressure
Out of Service
TB > Device Diagnostics > Status > Block Error > Out of Service
Outlet Pressure
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Outlet Pressure
Outblock Selection
TB > Configure/Setup > Detailed Setup > Response Control > Outblock Selection
TB > Configure/Setup > Detailed Setup > Alerts > Configuration Alerts > Output Block Timeout
Output Block Timeout Alert
TB > Configure/Setup > Detailed Setup > Alerts > Configuration Alerts > Output Block Timeout > Output Block Timeout Alert

Enable
TB > Configure/Setup > Detailed Setup > Alerts > Configuration Alerts > Output Block Timeout > Output Block Timeout Alert Enable
Output Block Timeout Manual

Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Configuration Alerts > Output Block Timeout > Output Block Timeout Manual
Recovery
Output Block Timeout Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Configuration Alerts > Output Block Timeout > Output Block Timeout Shutdown
Packing Type
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Packing Type
PD Inside Status
TB > Configure/Setup > Device Variables > PD Inside Status
PD Run
TB > Configure/Setup > Detailed Setup > Alerts > Performance Alerts > PD Run
Continued
263
Instruction Manual

August 2012
D103412X012

Parameter Label
Menu Structure
Performance Critical Alert
TB > Configure/Setup > Detailed Setup > Alerts > Performance Alerts > Performance Critical Alert
Performance Critical Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Performance Alerts > Performance Critical Alert Enable
Performance Information Alert
TB > Configure/Setup > Detailed Setup > Alerts > Performance Alerts > Peformance Information Alert

Enable
TB > Configure/Setup > Detailed Setup > Alerts > Performance Alerts > Peformance Information Alert Enable
Performance Reduced Alert
TB > Configure/Setup > Detailed Setup > Alerts > Performance Alerts > Peformance Reduced Alert

Enable
TB > Configure/Setup > Detailed Setup > Alerts > Performance Alerts > Peformance Reduced Alert Enable
Performance Tuner

TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning > Performance Tuner
TB > Configure/Setup > Detailed Setup > Alert Handling > PlantWeb Alert Simulate
Port Diameter
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Port Diameter
Port Type
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Port Type
Pressure A
TB > Device Variables > Pressures > Pressure A
Pressure A Sensor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Pressure A Sensor Alert
Pressure A Sensor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Pressure A Sensor Alert Enable
Pressure A Sensor Failure
TB > Device Diagnostics > Status > Self Test Status > Pressure A Sensor Error
Pressure A Sensor Manual

Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Pressure A Sensor Manual Recovery
Pressure A Sensor Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Pressure A Sensor Shutdown
Pressure B
TB > Device Variables > Pressures > Pressure B
Pressure B Sensor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Pressure B Sensor Alert
Pressure B Sensor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Pressure B Sensor Alert Enable
Pressure B Sensor Failure
TB > Device Diagnostics > Status > Self Test Status > Pressure B Sensor Error
Pressure Cutoff Closed
TB > Configure/Setup > Detailed Setup > Response Control > Travel Pressure Control > Pressure Cutoff Closed
Pressure Cutoff Open
TB > Configure/Setup > Detailed Setup > Response Control > Travel Pressure Control > Pressure Cutoff Open
Pressure Fallback Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Pressure Fallback > Pressure Fallback Alert
Pressure Fallback Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Pressure Fallback > Pressure Fallback Alert Enable
Pressure Integral Dead Zone
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning > Pressure Integral Dead Zone
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning > Pressure Integral Gain
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning > Pressure Integral Limit Hi
Pressure Integral Limit Lo
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning > Pressure Integral Limit Lo
Pressure MLFB Gain
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning > Pressure MLFB Gain
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning > Pressure Proportional Gain
Pressure Range Hi
TB > Configure/Setup > Detailed Setup > Response Control > Travel Pressure Control > Pressure Range Hi
Pressure Range Lo
TB > Configure/Setup > Detailed Setup > Response Control > Travel Pressure Control > Pressure Range Lo
Pressure Tuning Set
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning > Pressure Tuning Set
Pressure Units
TB > Configure/Setup > Detailed Setup > Instrument > Pressure Units
Processor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Processor Alert
Processor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Processor Alert Enable
Program Memory Alert
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Program Memory Alert
Program Memory Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Program Memory Alert Enable
Program Memory Manual

Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Program Memory Manual Recovery
Program Memory Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Program Memory Shutdown
Protection
TB > Device Variables > Protection
Proximity Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Hi Alert
Proximity Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Hi Alert Enable
Proximity Hi Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Hi Hi Alert
Proximity Hi Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Hi Hi Alert Enable
Proximity Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Lo Alert
Proximity Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Lo Alert Enable
Proximity Lo Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Lo Lo Alert
Proximity Lo Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Proximity > Proximity Lo Lo Alert Enable
Push Down To
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Push Down To
Continued
264
Instruction Manual
D103412X012
August 2012

Parameter Label
Menu Structure
Rated Travel
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Rated Travel
Relay Type
TB > Configure/Setup > Detailed Setup > Instrument > Relay Type
Seat Type
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Seat Type
Setpoint
TB > Device Variables > AO ControlPreChar > Setpoint
Setpoint Status
TB > Device Variables > AO ControlPreChar > Setpoint Status
Setpoint(D)
TB > Device Variables > DO Control > Setpoint(D)
Shaft Stem Diameter
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Shaft Stem Diameter
Simulate Active
TB > Device Diagnostics > Status > Block Error > Simulate Active
Simulate Jumper ON
TB > Device Diagnostics > Status > Self Test Status > Simulate Jumper ON
Spring Rate
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Spring Rate
Spring Rate Units
TB > Configure/Setup > Detailed Setup > Instrument > Spring Rate Units
Static Memory Alert
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Static Memory Alert
Static Memory Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Static Memory Alert Enable
Static Memory Manual Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Static Memory Manual Recovery
Static Memory Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Elect Alerts > Processor Impaired > Static Memory Shutdown
Stroke Time Close
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Reference > Stroke Time Close
Stroke Time Open
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Reference > Stroke Time Open
Supply
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Supply
TB > Device Variables > Pressures > Supply
Supply Pressure Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Supply Pressure Hi Alert
Supply Pressure Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Supply Pressure Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Supply Pressure Hi Alert Point
Supply Pressure Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Supply Pressure Lo Alert
Supply Pressure Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Supply Pressure Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Supply Pressure > Supply Pressure Lo Alert Point
Supply Pressure Sensor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Supply Pressure Sensor Alert

Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Pressure Sensors > Supply Pressure Sensor Alert Enable
Supply Sensor Failure
TB > Device Diagnostics > Status > Self Test Status > Supply Sensor Failure
Tag Description
TB > Configure/Setup > Detailed Setup > Instrument > Tag Description
Temperature
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Temperature
Temperature Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Temperature Hi Alert
Temperature Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Temperature Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Temperature Hi Alert Point
Temperature Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Temperature Lo Alert
Temperature Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Temperature Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment Alerts > Temperature Limit > Temperature Lo Alert Point
Temperature Sensor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Temperature Sensor > Temperature Sensor Alert
Temperature Sensor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Temperature Sensors > Temperature Sensor Alert Enable
Temperature Units
TB > Configure/Setup > Detailed Setup > Instrument > Temperature Units
Travel
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Travel
Travel (DeChar)
TB > Device Variables > AO ControlPreChar > Travel(DeChar)
Travel Accumulator
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts > Travel Accumulator > Travel Accumulator
TB > Device Variables > Travel Accumulator
Travel Accumulator Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts > Travel Accumulator > Travel Accumulator Alert
Travel Accumulator Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts > Travel Accumulator > Travel Accumulator Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts > Travel Accumulator > Travel Accumulator Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Travel History Alerts > Travel Accumulator > Travel Accumulator Deadband
Travel Closed Alert
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Travel Closed > Travel Closed Alert
Travel Closed Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Travel Closed > Travel Closed Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Travel Closed > Travel Closed Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Travel Closed > Travel Closed Deadband
Travel Count
TB > Device Variables > Travel Count
Travel Cutoff Hi
TB > Configure/Setup > Detailed Setup > Response Control > Travel Pressure Control > Travel Cutoff Hi
Continued
265
Instruction Manual

August 2012
D103412X012

Parameter Label
Menu Structure
Travel Cutoff Lo
TB > Configure/Setup > Detailed Setup > Response Control > Travel Pressure Control > Travel Cutoff Lo
Travel Deviation
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Deviation
Travel Deviation Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Deviation Alert
Travel Deviation Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Deviation Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Deviation Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Deviation Deadband
Travel Deviation Pressure

Fallback
TB > Configure/Setup > Detailed Setup > Response Control > Travel Pressure Control > Travel Deviation Pressure Fallback
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Deviation > Travel Deviation Time
Travel Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Hi Alert
Travel Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Hi Alert Point
Travel Hi Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Hi Deadband
Travel Hi Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Hi Hi Alert
Travel Hi Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Hi Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Hi Hi Alert Point
Travel Hi Hi Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Hi Hi Deadband
Travel Integral Dead Zone
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning > Travel Integral Dead Zone
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning > Travel Integral Enable
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning > Travel Integral Gain
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning > Travel Integral Limit Hi
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning > Travel Integral Limit Lo
Travel Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Lo Alert
Travel Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Lo Alert Point
Travel Lo Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Hi/Lo > Travel Lo Deadband
Travel Lo Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Lo Lo Alert
Travel Lo Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Lo Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Lo Lo Alert Point
Travel Lo Lo Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel Alerts > Travel Limit > Travel Lo Lo Deadband
Travel MLFB Gain
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning > Travel MLFB Gain
Travel Open Alert
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Travel Open > Travel Open Alert
Travel Open Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Travel Open > Travel Open Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Travel Open > Travel Open Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Prox Alerts > Travel Open > Travel Open Deadband
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning > Travel Proportional Gain
Travel Sensor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Travel Sensor > Travel Sensor Alert
Travel Sensor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Travel Sensor > Travel Sensor Alert Enable
Travel Sensor Hi Error
TB > Device Diagnostics > Status > Self Test Status > Travel Sensor Hi Error
Travel Sensor Lo Error
TB > Device Diagnostics > Status > Self Test Status > Travel Sensor Lo Error
Travel Sensor Manual Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Travel Sensor > Travel Sensor Manual Recovery
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Travel Sensor Motion
Travel Sensor Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Sensor Alerts > Travel Sensor > Travel Sensor Shutdown
Travel Sensor Span Error
TB > Device Diagnostics > Status > Self Test Status > Travel Sensor Span Error
Travel Status
TB > Device Variables > AO ControlPostChar > Travel Status
Travel Tuning Set
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning > Travel Tuning Set
Travel Units
TB > Configure/Setup > Detailed Setup > Instrument > Travel Units
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning > Travel Velocity Gain
Travel(D)
TB > Device Variables > DO Control > Travel(D)
TB > Configure/Setup > Detailed Setup > Response Control > Travel Pressure Control > Travel/Pressure Select
TB > Configure/Setup > Detailed Setup > Response Control > Travel Pressure Control > Travel/Pressure State
TB > Device Variables > Travel/Pressure State
Trend
TB > Device Diagnostics > Trend
Trim Style 1
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Reference > Trim Style 1
Continued
266
Instruction Manual
D103412X012
August 2012

Parameter Label
Menu Structure
Trim Style 2
Unbalanced Area
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Unbalanced Area
Upper Bench Set
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Upper Bench Set
Valve Class
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Class
Valve Manufacturer
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Manufacturer
Valve Model Number
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Model Number
Valve Serial Number
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Serial Number
Valve Size
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Size
Valve Style
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Style
TB > Configure/Setup > Detailed Setup > Instrument > Zero Power Condition
TRANSDUCER BLOCK
BASIC SETUP
Top Level
Configure/Setup
Device Diagnostics
Device Variables
Configure/Setup
Basic Setup
Detailed Setup
Calibration
Basic Setup
Device Setup
Performance Tuner
267
Instruction Manual

August 2012
D103412X012
Travel Tuning
TRANSDUCER BLOCK
DETAILED SETUP
:Travel Tuning Set

:Travel MLFB Gain
:Travel Integral Enable
:Travel Integral Gain
:Travel Integral Dead Zone
:Travel Integral Limit Hi
:Travel Integral Limit Lo
Performance Tuner
Stabilize / Optimize
Response Control
Travel Tuning
Pressure Tuning
Travel Press Control
Outblock Selection
Top Level
Configure/Setup
Device Diagnostics
Device Variables
Travel Press Control
Configure/Setup
Basic Setup
Detailed Setup
Calibration
Detailed Setup
Protection
Response Control
Alerts
Instrument
Valve and Actuator
MAI Channel Map
Alert Handling
MAI Channel Map
Alert Handling
Simulate Active Alerts
:MAI Channel 1
:MAI Channel 2
:MAI Channel 3
:MAI Channel 4
:MAI Channel 5
:MAI Channel 6
:MAI Channel 7
:MAI Channel 8
:Travel/Pressure State
:Travel/Pressure Select
Travel Deviation Pressure Fallback
Travel Cutoff Hi
Travel Cutoff Lo
:Pressure Cutoff Open
:Pressure Cutoff Closed
:Pressure Range Hi
:Pressure Range Lo
Tag Description
Pressure Units
Temperature Units
Travel Units
Length Units
Area Units
Spring Rate Units
:Relay Type
:Zero Power Condition
:Maximum Supply Pressure
Calibration Person
Calibration Date
:Last Calibration Type
Simulate Active Alarms
Valve and Actuator

Block Error Reporting
Failed Active
Maint Active
Advise Active
Valve
Trim
Actuator
Reference
Reference
268
:Pressure Tuning Set

:Pressure Proportional Gain
:Pressure MLFB Gain
:Pressure Integral Gain
:Pressure Integral Dead Zone
:Pressure Integral Limit Hi
:Pressure Integral Limit Lo
Alerts (See facing page)

Instrument
:Trim Style 1
:Trim Style 2
:Stroke Time Open
:Stroke Time Close
Pressure Tuning
Actuator
:Actuator Style
:Actuator Size
:Feedback Connection
:Travel Sensor Motion
:Lever Style
:Lever Arm Length
:Effective Area
:Air
:Upper Bench Set
:Lower Bench Set
:Nominal Supply Pressure
:Spring Rate
Elect Alerts
Sensor Alerts
Environment Alerts
Travel Alerts
Prox Alerts
Performance Alerts
Valve
Valve Manufacturer
Valve Model Number
Valve Serial Number
Valve Style
:Valve Size
:Valve Class
:Rated Travel
:Actual Travel
:Shaft Stem Diameter
:Packing Type
:Inlet Pressure
:Outlet Pressure
Trim
:Seat Type
:Leak Class
:Port Diameter
:Port Type
:Flow Direction
:Push Down To
:Flow Tends To
:Unbalanced Area
Instruction Manual
D103412X012
August 2012
Drive Current
TRANSDUCER BLOCK
DETAILED SETUP > ALERTS
(continued on next page)
Drive Current
:Drive Current Alert
:Drive Current Alert Enable
:Drive Current Shutdown
:Drive Current Manual Recovery
:Drive Current Alert Point
:Drive Current Alert Time
Elect Alerts
Drive Current
Drive Signal
Processor Impaired
Alerts
Elect Alerts
Sensor Alerts
Environment Alerts
Travel Alerts
Prox Alerts
Performance Alerts
Alert Key
Drive Signal
Processor Impaired
:Program Memory Alert
:Program Memory Alert Enable
:Program Memory Shutdown
:Program Memory Manual Recovery
:Static Memory Alert
:Static Memory Alert Enable
:Static Memory Shutdown
:Static Memory Manual Recovery
:Processor Alert
:Processor Alert Enable
:I/O Processor Alert
:I/O Processor Alert Enable
:I/O Processor Shutdown
:I/O Processor Man Recovery
Drive Signal
:Drive Signal Alert
:Drive Signal Alert Enable

:Blocks Set to Defaults Alert
:Blocks Set to Defaults Alert Enable
:Output Block Timeout Alert

:Output Block Timeout Alert Enable
:Output Block Timeout Shutdown
:Output Block Timeout Manual Recovery
:Output Block Timeout
Sensor Alerts
Travel Sensor
Pressure Sensors
Pressure Fallback
Temperature Sensor
Travel Sensor
Pressure Fallback
:Pressure Fallback Alert
:Pressure Fallback Alert Enable
Temperature Sensor
:Temperature Sensor Alert
:Temperature Sensor Alert Enable
Environment Alerts
Supply Pressure
Temperature Limit
Temperature Limit
Temperature
:Temperature Hi Alert
:Temperature Hi Alert Enable
:Temperature Lo Alert
:Temperature Lo Alert Enable
:Temperature Lo Alert Point
Supply Pressure
:Travel Sensor Alert

:Travel Sensor Alert Enable
:Travel Sensor Shutdown
:Travel Sensor Manual Recovery
Pressure Sensors
:Pressure A Sensor Alert
:Pressure A Sensor Alert Enable
:Pressure A Sensor Shutdown
:Pressure A Sensor Manual Recovery
:Pressure B Sensor Alert
:Pressure B Sensor Alert Enable
:Supply Pressure Sensor Alert
:Supply Pressure Sensor Alert Enable
:Supply
:Supply Pressure Hi Alert
:Supply Pressure Hi Alert Enable
:Supply Pressure Lo Alert
:Supply Pressure Lo Alert Enable
:Supply Pressure Lo Alert Point
269
Instruction Manual

August 2012
D103412X012
TRANSDUCER BLOCK
DETAILED SETUP > ALERTS
Alerts
Travel Open
Elect Alerts
Sensor Alerts
Environment Alerts
Travel Alerts
Prox Alerts
Performance Alerts
Travel Open Alert

:Travel Open Alert Point
:Travel Open Deadband
Travel Alerts
Travel Deviation
:Travel Target
:Travel
Travel Deviation
Travel Limit
Travel Hi/Lo
Travel Deviation
:Travel Deviation Alert
:Travel Deviation Alert Enable
:Travel Deviation Alert Point
:Travel Deviation Time
:Travel Deviation Deadband
Travel Limit
:Travel Hi Hi Alert
:Travel Hi Hi Alert Enable
:Travel Hi Hi Alert Point
:Travel Hi Hi Deadband
:Travel Lo Lo Alert
:Travel Lo Lo Alert Enable
:Travel Lo Lo Alert Point
:Travel Lo Lo Deadband
Prox Alerts
:Travel
Travel Open
Travel Closed
Proximity
Travel Hi/Lo
:Travel Hi Alert
:Travel Hi Alert Enable
:Travel Hi Alert Point
:Travel Hi Deadband
:Travel Lo Alert
:Travel Lo Alert Enable
:Travel Lo Alert Point
:Travel Lo Deadband
Proximity
:Proximity Hi Hi Alert
:Proximity Hi Hi Alert Enable
:Proximity Hi Alert
:Proximity Hi Alert Enable
:Proximity Lo Alert
:Proximity Lo Alert Enable
:Proximity Lo Lo Alert
:Proximity Lo Lo Alert Enable

Failed Suppress
Advise Suppress
Travel Closed
:Travel Closed Alert
:Travel Closed Alert Enable
:Travel Closed Alert Point
:Travel Closed Deadband
Failed Enable
Maintenance Enable
Advise Enable
Cycle Counter
Travel Accumulator
Performance Alerts
:PD Inside Status
:PD Run
Performance Reduced
Cycle Counter
:Cycle Counter Alert
:Cycle Counter Alert Enable
:Cycle Counter Alert Point
:Cycle Counter Deadband
Travel Accumulator
Travel Accumulator
:Travel Accumulator Alert
:Travel Accumulator Alert Enable
:Travel Accumulator Alert Point
:Travel Accumulator Deadband
Performance Information Alert Enable
270
Cycle Counter
Performance Reduced

Performance Reduced Alert Enable

Instruction Manual
D103412X012
August 2012
TRANSDUCER BLOCK
CALIBRATION
Top Level
Configure/Setup
Device Diagnostics
Device Variables
Configure/Setup
Basic Setup
Detailed Setup
Calibration
Calibration
Auto Calibration
Manual Calibration
Relay
Supply Pressure
Pressure A
Pressure B
TRANSDUCER BLOCK
DEVICE DIAGNOSTICS
Status
Top Level
Configure/Setup
Device Diagnostics
Device Variables
Self Test Status

Block Error
Device Diagnostics
Active PlantWeb Alerts
Alert Conditions
Status
Device Record
Stroke Valve
Trend
Block Error
Simulate Active
Lost Static Data
Out of Service
Device Record
:Maximum Recorded Temperature
:Maximum Recorded Temperature Time
:Minimum Recorded Temperature
:Minimum Recorded Temperature Time
:Maximum Recorded Supply Pressure
:Maximum Recorded Supply Pressure Time
:Minimum Recorded Supply Pressure
:Minimum Recorded Supply Pressure Time
TRANSDUCER BLOCK
DEVICE VARIABLES
Self Test Status

MLFB Error
IOP Failure
Drive Current Alert
Simulate Jumper ON
AO Control - PreChar
Top Level
Device Variables
Configure/Setup
Device Diagnostics
Device Variables
All Block Modes

AO Control - PreChar
AO Control - PostChar
DO Control
:Travel/Pressure State
:PD Inside Status
Protection
Drive Signal
Temperature
Cycle Counter
Travel Accumulator
:Travel Count
Pressures
:Setpoint
:Setpoint Status
:Travel (DeChar)
AO Control - PostChar
:Travel Target
:Travel
:Travel Status
DO Control
:Setpoint(D)
:Travel(D)
Pressures
:Supply
:Pressure A
:Pressure B
:A Minus B
271
Instruction Manual

August 2012
D103412X012
Resource Block (RB) Menu Structure

Parameter Label
Menu Structure
Alert Key
RB > Configure/Setup > Alarm Handling > Alert Key
RB > Device Diagnostics > Block Alarm > Alarm State
RB > Device Diagnostics > Block Alarm > Unacknowledge
Block Alarm Disabled
RB > Configure/Setup > Alarm Handling > Block Alarm Disabled
Block Alarm Automatically

Acknowledge
RB > Configure/Setup > Alarm Handling > Block Alarm Automatically Acknowledge
Confirm Time
RB > Configure/Setup > Alarm Handling > Confirm Time
DD Information
RB > Device Variables > DD information
Device ID
RB > Configure/Setup > Identification > Device ID or RB > Device Variables > Instrument > Identification > Device ID
Device Revision
RB > Configure/Setup > Version > Device Revision or RB > Device Variables > Instrument > Version > Device Revision
Device State
RB > Display > Resource Status > Device State

RB > Device Diagnostics > Device State
Device Type
RB > Configure/Setup > Identification > Device Type or RB > Device Variables > Instrument > Identification > Device Type
Diagnostics Options
RB > Configure/Setup > Options > Diagnostics Options
Discrete Alarm Disabled
RB > Configure/Setup > Alarm Handling > Discrete Alarm Disabled
Discrete Alarm Automatically

Acknowledge
RB > Configure/Setup > Alarm Handling > Discrete Alarm Automatically Acknowledge
RB > Configure/Setup > Identification > Elect S/N or RB > Device Variables > Instrument > Identification > Electronics Serial Number
RB > Configure/Setup > Identification > Factory S/N or RB > Device Variables > Instrument > Identification > Factory Serial Number
Fault State
RB > Device Diagnostics > Maintenance > Fault State
Features Available
RB > Configure/Setup > Options > Features Available or RB > Device Variables > Options > Features Available
Features Selected
RB > Configure/Setup >Options > Features Selected
Field Serial Number
RB > Configure/Setup > Identification > Field S/N or RB > Device Variables > Instrument > Identification > Field Serial Number
Firmware Revision
RB > Configure/Setup > Version > Firmware Revision or RB > Device Variables > Instrument > Version > Firmware Revision
RB > Configure/Setup > Options > Function Block Options or RB > Device Variables > Options > Function Block Options
Hardware Revision
RB > Configure/Setup > Version > Hardware Revision or RB > Device Variables > Instrument > Version > Hardware Revision
ITK Version
RB > Configure/Setup > Version > ITK Version or RB > Device Variables > Instrument > Version > ITK Version
Limit Notify
RB > Configure/Setup > Alarm Handling > Limit Notify
Manufacturer
RB > Configure/Setup > Identification > Manufacturer or RB > Device Variables > Instrument > Identification > Manufacturer
Maximum Notify
RB > Configure/Setup > Alarm Handling > Maximum Notify
RB > Configure/Setup > Options >Miscellaneous Options or RB > Device Variables > Options >Miscellaneous Options
RB > Device Diagnostics > Resource Block Error
Shed Remote Cascade
RB > Configure/Setup > Communication Time Out > Shed Remote Cascade
Shed Remote Out
RB > Configure/Setup > Communication Time Out > Shed Remote Out
Standby Firmware Revision
RB > Configure/Setup > Version > Standby Software Revision or RB > Device Variables > Instrument > Version > Standby Software
Revision
Strategy
RB > Configure/Setup > Identification > Strategy or RB > Device Variables > Instrument > Identification > Strategy
Tag Description
RB > Configure/Setup > Identification > Tag Description or RB > Device Variables > Instrument > Identification > Tag Description
RB > Device Diagnostics > Write Lock > Write Alarm: Alarm State
Write Lock
RB > Configure/Setup > Write Lock > Write Lock or RB > Device Diagnostics > Write Lock > Write Lock
Write Priority
RB > Configure/Setup > Write Lock > Write Priority
272
Instruction Manual
D103412X012
August 2012
Write Lock
Write Priority
Configure/Setup
Device Diagnostics
Device Variables
Shed Remote Cascade

Shed Remote Out
Resource Block Mode

Write Lock
Comm Timeout
Options
Alarm Handling
Identification
Version
Options
Device Revision
Firmware Revision
Hardware Rev
ITK Version
Identification
Device ID
Field Serial Number
Tag Description
Strategy
Manufacturer
Device Type
Diagnostics Options
Features Available
Alert Key
Confirm Time
Limit Notify
Maximum Notify
Block Alm Disabled
Block Alarm Auto Acknowledge
Disc Alm Disabled
Discrete Alarm Auto Acknowledge
Reports
Fault State
Soft W Lock
Multibit Alarm (BitAlarm) Support
Maintenance
Restart Actions
Fault State
Set Fault State
Clear Fault State
RESOURCE BLOCK
DEVICE VARIABLES
Top Level
Instrument
Configure/Setup
Device Diagnostics
Device Variables
Device Variables
Instrument
Options
DD Information
Options
Diagnostics Options
Features Available
Features Selected
Reports
Fault State
Soft W Lock

Device State
Write Lock
Block Alarm
Maintenance
Configure/Setup
Device Diagnostics
Device Variables
Firmware Download
Travel Control Capable
Pressure Control Capable
Pressure Fallback Capable
Alarm Handling
Device Diagnostics
Top Level
Diagnostics Options
Features Available
Features Selected
Version
RESOURCE BLOCK
DEVICE DIAGNOSTICS
AO
DO
AI
DI
PID
IS
OS
MAI
Comm Timeout
Configure/Setup
Top Level
Function
Block Options
Write Lock
RESOURCE BLOCK
CONFIGURE/SETUP
Identification
Version
Function
Block Options
AO
DO
AI
DI
PID
IS
OS
MAI
Features Available
Reports
Fault State
Soft W Lock
Firmware Download
Travel Control Capable
Pressure Control Capable
Pressure Fallback Capable
Other
Simulate Active
Memory Failure
Lost Static Data
Lost NV Data
Power Up
Out of Service
Write Lock
Write Alarm Alarm State
Write Lock
Block Alarm
Block Alarm Alarm State
Block Alarm Unacknowledged
Identification
Device ID
Field Serial Number
Tag Description
Strategy
Manufacturer
Device Type
Version
Device Revision
Firmware Revision
Hardware Rev
ITK Version
273

August 2012
274
Instruction Manual
D103412X012
Instruction Manual
D103412X012
PlantWeb Alerts
August 2012
Appendix C PlantWeb AlertsCC

Instrument Alert Conditions
To view these alerts, the user must open the appropriate status screen on a host such as a DeltaV system, ValveLink
software or a Field Communicator.
PlantWeb Alerts
Some instrument alert conditions can also be used to trigger PlantWeb alerts that will be reported in Failed,
Maintenance or Advisory categories, as configured by the user. PlantWeb alerts, when enabled, can participate in the
DeltaV alarm interface tools such as the alarm banner, alarm list and alarm summary. For specific information on
setting up PlantWeb Alerts in a DeltaV system, refer to the PlantWeb Alerts section in Appendix F.
When a PlantWeb alert occurs, the DVC6200f sends an event notification and waits a specified period of time for an
acknowledgment to be received. This occurs even if the condition that caused the alert no longer exists. If the
acknowledgment is not received within the prespecified timeout period, the event notification is retransmitted. This
reduces the possibility of alert messages getting lost.
ModeBased PlantWeb Alerts

Some PlantWeb alerts are not active unless the transducer block (actual) mode is Auto.
1. Alerts which can be triggered by the activities of the service technician are reported only when the transducer block
mode is AUTO.
2. Alerts which are unrelated to service technician activities are reported in all transducer block modes.
Exceptions are as follows:
Alerts can be simulated regardless of transducer block mode but must be enabled to be reported.
When a shutdown condition exists (either currently active or latched on through the shutdown recovery parameter)
in the transducer block, alerts are reported even though the mode of the transducer block is OOS.
Refer to table C1 for reporting of PlantWeb Alerts.
Alert Handling
Alert handling is diagrammed in figure C1. There are two ways of seeing PlantWeb alerts. One way is to see if the
instrument alert condition causing a PlantWeb alert is detected. The second is to view alerts reported to the system
operator console. For a PlantWeb alert to be active, it has to pass four tests. The first is to check if the Instrument alert
condition is enabled. If a condition is not enabled, the instrument does not check for the alert condition.
Second, the condition that will cause an alert must exist. For example, the current travel is above the Travel Limit Hi
Alert Point.
Third, the corresponding PlantWeb alert must be enabled in one or more of the three categories: Failed, Maintenance
or Advise.
Fourth, the transducer block mode must be correct. See table C1.
Note
Additional details on setting up and using Instrument Alerts can be found on page 69 of this manual.
275
Instruction Manual
PlantWeb Alerts
August 2012
D103412X012
Figure C1. Alert Handling

Set Alert Points
and Deadband in
the Transducer
Block
START
"
ALERT
CONDITION
ENABLED?
Enable Instrument
Alert Condition in
the Transducer
Block
Yes
"
LIMITS EXCEEDED TO
CAUSE ALERT?
No
Enable PlantWeb
Alert in the
Transducer Block
Yes INSTRUMENT
" ALERT
CONDITION
ACTIVE
Yes
"
Use Resource and Transducer

Block Parameters to Configure
Yes
"
PLANTWEB
ALERT
ENABLED?
No
No
Yes
PLANTWEB
" ALERT ACTIVE
No
NO ACTIVE
PLANTWEB ALERT
1
TRANSDUCER
BLOCK MODE
AUTO
B
NO ACTIVE INSTRUMENT
ALERT CONDITION
No
REPORT
ALERTS?
Yes
B
No
Select Reports
Supported from
FEATURE_SEL in the
Resource Block
PRIORITY
>1?
Set Priority with

PlantWeb Alarm
Priority parameters in
Transducer Block using
DeltaV
B Yes
B
Instrument Alert
Conditions active,
but not reported
NOTE:
1
CERTAIN
PLANTWEB ALERTS ARE MODEBASED.
SEE TABLE C1 FOR DETAILS.
Table C1. PlantWeb Alerts Reporting Requirements
276
PlantWeb Alert
Transducer Block Mode (Actual)
Drive Current
AUTO
Drive Signal
AUTO
Processor Impaired
Any Mode
Any Mode
Block Set to Defaults
Any Mode
Travel Sensor
AUTO
Output Pressure Sensor
Any Mode
Supply Pressure Sensor
Any Mode
Temperature Sensor
Any Mode
Supply Pressure
AUTO
Temperature Limit
AUTO
Travel Deviation
AUTO
Travel Limit
AUTO
Cycle Counter
AUTO
Travel Accumulator
AUTO
AUTO
Performance Reduced
AUTO
AUTO
Pressure Fallback
AUTO
Yes
SUPPRESS
REPORTINGAL
ERT
CONDITION?
B No
PLANTWEB
ALERTS
REPORTED
Suppress Alert
Condition Reporting
with Alarm Suppress
Parameters in
Transducer Block
Instruction Manual
D103412X012
PlantWeb Alerts
August 2012
Alert Reporting
For PlantWeb alerts to be reported to the operator console, they must pass four tests:
Alerts must be active
Reports must be selected in Feature Select
Alert priority must be greater than 1
Reporting must not be suppressed for those conditions that caused active alerts.
Features Selected in the Resource block determines if reporting by the instrument is supported. Refer to page 47 for
additional information on Features Selected.
Failed Priority (FAILED_PRI [68]), Maintenance Priority (MAINT_PRI [69]), and Advise Priority (ADVISE_PRI [70])
determine the PlantWeb alert priorities. Although 16 priorities are available only three are actually meaningful for
PlantWeb alerts. If the priority is 0, no reporting occurs. If the priority is 1, reporting is simulated within the
instrument, but the alert is not actually reported over the bus. The alert condition is reported for priorities 2 through
15, with the higher priorities taking precedence over the lower priorities.
Failed Suppress (FAILED_MASK [65]), Maintenance Suppress (MAINT_MASK [66]), and Advise Suppress (ADVISE_MASK
[67]) determine which of the alert conditions are suppressed so that they are not reported.
PlantWeb Alerts Set Block Status

If a PlantWeb Alert is active, the AO or DO Block Readback parameter status may change. This behavior is controlled
with the PlantWeb Alerts Set PV Status (PWA_SET_STATUS [97]) parameter in the transducer block
Setting PlantWeb Alerts

Refer to table C2 for information on setting PlantWeb alerts. When selected, PlantWeb alarms will set the PV status
according to table C4.
Using PlantWeb Alerts

Refer to table C3 for information on using PlantWeb alerts.
277
Instruction Manual
PlantWeb Alerts
August 2012
D103412X012
Table C2. Setting PlantWeb Alerts

PlantWeb Alert
(Group)
(Default Alert Category)
Drive Current
(Electronics)
(Failed)
Alert Condition
(Default)
Drive Current
(Enabled)
What the Alert is Detecting
Related Parameters
(Default)
The difference between the

expected Drive Current and the
actual Drive Current has
exceeded the Drive Current
Alert Time.
Self Test Shutdown (No)

Shutdown Recovery (Auto)
Alert Point (50%)
Alert Time (5 sec)
Guidelines for Setting
Use default settings
If one of the following

conditions exist:
Drive Signal
(Electronics)
(Maintenance)
Drive Signal
(Enabled)
Where Zero Power Condition is

defined as closed:
Drive Signal < 10% and
Calibrated Travel > 3%
Drive Signal > 90% and
Calibrated Travel < 97%
Use default setting

defined as open:
Processor Impaired
(Electronics)
(Maintenance)

(Configuration)
(Maintenance)
Program Memory
(Enabled)
A pending Flash or NVM failure

is present.

Static Memory
(Enabled)
A failure of the FRAM memory

where static parameters are
stored.

Processor
(Enabled)
A failure of the main Processor.

I/O Processor
(Enabled)
A failure of the I/O Processor.

Output Block
Timeout
(Disabled)
If the analog or discrete output

block has not executed for
longer than the configured
timeout.
Timeout Alert Point (600 s)

Enable this alert for loops where the

execution is critical. If the AO or DO block
is not scheduled, or scheduled incorrectly,
it will trigger an alert after the Timeout
Alert Point has been exceeded. Set the
Timeout Alert Point to a value between
a. 30 seconds and
b. the maximum time before a user
should be notified. The minimum number
depends on the time it takes for a host to
download a configuration to the device.
Shutdown can be enabled if it is desired to
move the valve to the Zero Power
Condition at the same time that the alert
is generated.

(Configuration)
(Maintenance)

(Enabled)
If the resource block has

undergone Restart with
Defaults
None
Shutdown Alert
(Configuration)
(Maintenance)
N/A
A user configured Self Test

Shutdown condition has taken
the instrument to OOS.
None
-Continued-
278
Instruction Manual
PlantWeb Alerts
D103412X012
August 2012
Table C2. Setting PlantWeb Alerts (Continued)

PlantWeb Alert
(Group)
Alert Condition
(Default)
Related Parameters
(Default)

Double Acting Actuators Enable the
alert and configure it to report in the
Failed Alert Category. Self Test Shutdown
is generally not enabled.
Travel Sensor
(Sensors)
(Failed)
Travel Sensor
(Enabled)
The travel feedback is within

acceptable limits.

Single Acting Actuators

If Travel / Pressure Control is configured
as Travel with Pressure Fallback: enable
the alert and configure it to report in the
Maintenance Alert Category. Do not
enable Self Test Shutdown.
IIf Travel / Pressure Control is configured
as Travel: Enable the alert and configure it
to report in the Failed Alert Category. Self
Test Shutdown is generally not enabled.
Output Press Sensor

(Sensors)
(Maintenance)
Port A Pressure
Sensor (Enabled)
The pressure sensor reading is

outside the functional range of
the sensor.
Port B Pressure
Sensor (Enabled)

If Travel / Pressure Control is configured

as Pressure: enable the alert and
configure it to report in the Failed Alert
Category. Enable the Self Test Shutdown.
For all other Travel / Pressure Control
selections, enable the alert to report in
the Maintenance Alert Category and do
not enable the Self Test Shutdown.
None
Supply Press Sensor

(Sensors)
(Advisory)
Supply Press Sensor

(Enabled)

the sensor.
None
Temperature Sensor
(Sensors)
(Advisory)
Temperature Sensor
(Enabled)
The temperature sensor

reading is outside the
functional range of the sensor.
None
Pressure Fallback (Sensors)

(Maintenance)
Pressure Fallback
(Enabled)
A travel sensor failure or large

travel deviation has resulted in
fallback to pressure control.
None
Alert Point (145 psig)
Enable the alert in the Maintenance Alert

Category. Set the Alert Point to which
ever is lower of
a. the maximum instrument pressure of
145 psig or
b. the maximum actuator casing
pressure.
Alert Point (19 psig)

Category.
Double Acting Actuators Set the Alert
Point above the minimum required for
valve shutoff and no greater than
1 psig below the supply regulator setting
Single Acting Actuators Set the Alert
Point above the minimum required for
valve shutoff and no greater than
1 psig below the supply regulator setting.
This is generally about 3 psig above the
actuator upper bench set (stroking)
pressure.
Supply Press High

(Enabled)
The supply pressure has

exceeded the Supply Pressure
Hi Alert Point.
Supply Pressure
(Environment)
(Maintenance)
Supply Press Low
(Enabled)
The supply pressure is lower

than the Supply Pressure Lo
Alert Point.
-Continued-
279
Instruction Manual
PlantWeb Alerts
August 2012
D103412X012

PlantWeb Alert
(Group)
Alert Condition
(Default)
Related Parameters
(Default)

Temperature High
(Enabled)
Temperature Limit
(Environment)
(Advisory)
Temperature Low
(Enabled)
The temperature is greater

than the Temperature Hi Alert
Point.
The temperature is lower than

the Temperature Lo Alert
Point.
Alert Point ( 186F)
Alert Point ( -63F)
Other alert points may be chosen to

indicate changes in the instrument
environment.
Category. Set the Alert Point at -40F if
the instrument uses Nitrile elastomers
and -63F if it uses Fluorosilicone
elastomers.
Other alert points may be chosen to
indicate changes in the instrument
environment.
Category. Use the default settings with
valves that are 4 inch and smaller with
PTFE packing systems.
Travel Deviation
(Travel)
(Maintenance)
Travel Limit
(Travel)
(Advisory)
N/A
(Travel)
(N/A)
N/A
(Proximity)
(N/A)
Travel Deviation
(Enabled)
Alert Point (5%)

Alert Time (10 sec)
Deadband (2%)
Travel Limit Hi Hi
(Disabled)
The Travel has exceeded the

Travel Limit Hi Hi Alert Point
Alert Point (125%)

Deadband (5%)
Enable this alert for critical loops, where it

is important to alert an operator if the
valve is approaching the wide open
position. A typical setting might be 95%.
Travel Limit Lo Lo
(Disabled)
The Travel is lower than the

Travel Limit Lo Lo Alert Point.
Alert Point (-25%)

Deadband (5%)
Enable this alert for critical loops, where it

is important to alert an operator if the
valve is approaching the closed position.
A typical setting might be 5%.
Travel Limit Hi
(Disabled)

Travel Limit Hi Alert Point.
Alert Point (125%)

Deadband (5%)
Use the Alert Points and Deadband to

configure the Proximity Alerts below.
Travel Limit Lo
(Disabled)

Travel Limit Lo Alert Point.
Alert Point (-25%)

Deadband (5%)
Use the Alert Points and Deadband to

configure the Proximity Alerts below.
Travel Open
(Disabled)
The Travel is greater than the

Open Alert Point
Alert Point (99.5%)

Deadband (5%)
Enable and set to report Travel with DI

Block
Travel Closed
(Disabled)

Closed Alert Point
Alert Point (0.5%)

Deadband (5%)

Block
Alert Point (125%)

Deadband (5%)

Block
Alert Point (125%)

Deadband (5%)

Block
Alert Point (-25%)

Deadband (5%)

Block
Alert Point (-25%)

Deadband (5%)

Block
Alert Point (1,000,000)

Deadband (1%)
Bellows Seal Bonnets enable the alert in

the Maintenance Alert Category. Use the
bellows manufacturer's cycle life data to
set cycle limits.
Proximity Hi Hi
(Disabled)
Proximity Hi
(Disabled)
Proximity Lo
(Disabled)
The Travel is within the

configured band of the
configured center point.
Proximity Lo Lo
(Disabled)
Cycle Counter
(Travel History)
(Maintenance)
Cycle Counter
(Disabled)
The number of travel reversals

has exceeded the configured
limit.
-Continued-
280
With other valves, the user can refine the

settings with ValveLink software Dynamic
Error Band and Step Response Tests. Set
the related parameters as follows:
Tvl Dev Alert Pointset equal times 2 the
Maximum Dynamic Error, minimum 3%
Tvl Dev DBset equal to the Dynamic
Error Band, minimum 2%
Tvl Dev Timeset equal to the T98 time
for a Step Test from 0 to 100% Travel,
minimum 10 seconds.
The Travel Deviation has

exceeded the Travel Deviation
Alert Point by more than the
Travel Deviation Time.
Instruction Manual
PlantWeb Alerts
D103412X012
August 2012

PlantWeb Alert
(Group)
Alert Condition
(Default)
Related Parameters
(Default)
Travel Accumulator
(Travel History)
(Maintenance)
Travel Accumulator
(Disabled)
The accumulated travel has

exceeded the configured limit.
Alert Point (1,000,000)

Deadband (1%)
Packing Bonnets enable the alert in the

Maintenance Alert Category. When
packing leaks are discovered, set the
Travel Accumulator alert to 90% of the
current Travel Accumulator Value,
triggering an alert prior to anticipated
leak.
(Performance)
(Failed)
(Enabled)
Critical performance issues

based on continuous PD tests
internal to the instrument.
None
Use default setting
Performance Reduced
(Performance)
(Maintenance)
Performance
Reduced
(Enabled)
Reduced performance issues

None
Use default setting
(Performance)
(Advisory)
Performance
Information
(Enabled)
None
Use default setting
Table C3. Using PlantWeb Alerts

PlantWeb Alert
(Group)
(Default Alert Category
Alert Condition
(Default)
Effect on Valve/Instrument
Recommended
Action
Help
Drive Current
(Electronics)
(Failed)
Drive Current
(Enabled)
The difference between the

expected Drive Current and the
actual Drive Current has
exceeded the Drive Current
Alert Time.
If configured for Self Test

Shutdown, then the transducer
Actual mode is placed Out of
Service until the problem is
fixed. Out of Service results in
the instrument output
pressure(s) and actuator
position being at the Zero
Power Condition.
Check I/P module
The instrument has

detected that the
difference between the
expected Drive Current
and the actual Drive
Current is greater than
the configured limit
1) Replace the I/P
module
2) Calibrate the device.
If the problem persists,
replace the printed
wiring board (PWB)
assembly.
Drive Signal
(Electronics)
(Maintenance)
Drive Signal
(Enabled)
If one of the following

conditions exist:
None - Indicates reduced

performance.
Check instrument
pneumatics
The instrument I/P

drive signal necessary
to generate the
pressure output from
the instrument is not
within the expected
range. Potential causes
include I/P filter
plugged, instrument
pneumatic relay failure,
low supply pressure, air
leaks, or valve sticking.
Test the control valve
assembly for proper
operation. ValveLink
diagnostics can be used
for this purpose.

defined as closed:
defined as open:
-Continued-
281
Instruction Manual
PlantWeb Alerts
August 2012
D103412X012
Table C3. Using PlantWeb Alerts (Continued)

PlantWeb Alert
(Group)
Processor Impaired
(Electronics)
(Maintenance)

(Configuration)
(Maintenance
Alert Condition
(Default)
Recommended
Action
Program Memory
(Enabled)
A pending Flash or NVM failure

is present.
Replace PWB
assembly
Static Memory
(Enabled)
A failure of the FRAM memory

where static parameters are
stored.
An error has been

detected in the printed
wiring board (PWB)
assembly. Replace the
PWB assembly.
Processor
(Enabled)
A failure of the main Processor.
I/O Processor
(Enabled)
A failure of the I/O Processor.

Power Condition.
Output Block
Timeout
(Disabled)
If the AO or DO block has not

executed for longer than the
configured timeout, this alert is
detected.

Power Condition.
Check Output
Block
The function block

providing the setpoint
for the valve position
(AO or DO function
block) has not executed
within the user
configured time limit. If
configured for Self Test
Shutdown, the
transducer Actual
mode is set to Out of
Service.
Help
1) Download the
control schedule from
the host configuration
device.
2) Make sure the Time
Out Alert Point is
greater than the block
execution schedule.
This alert should only
be utilized in very
critical loops where
execution time is
critical.
(Configuration)
(Failed)
Blocks Set to
Default
(Enabled)
If the resource block has

undergone Restart with
Defaults.
The transducer Actual mode

is placed Out of Service when
the defaults are applied. Out of
service results in the actuator
being at the Zero Power
Condition.
Download device
configuration
When restoring power

to the device, the
configuration
parameters could not
be recalled from
nonvolatile memory.
When the instrument
detects this condition,
the transducer Actual
mode is set to Out of
Service.
To correct this
situation, download the
configuration to the
device and set the
Target Mode of the
Resource block.
Shutdown Alert
(Configuration)
(Failed)
N/A
A user configured Self Test

Shutdown condition has taken
the instrument to OOS.
None - Indicates why the

instrument remains OOS.
-Continued-
282
Same as the
configured Self
Test Shutdown.
The instrument Actual

mode remains OOS due
to a configured Self
Test Shutdown, where
Manual Recovery was
specified, even though
the condition may have
cleared. Check
Recommended Action
for the indicated
condition.
Instruction Manual
PlantWeb Alerts
D103412X012
August 2012

PlantWeb Alert
(Group)
Travel Sensor
(Sensors)
(Failed)
Alert Condition
(Default)
Travel Sensor
(Enabled)
The travel feedback is within

acceptable limits.

fixed. Out of service results in
the actuator being at the Zero
Power Condition.
Recommended
Action
Check mounting
and linkage
Help
Travel feedback value is
outside expected
limits. If this problem
occurs during
instrument setup, the
most likely cause is
faulty mounting or
improper adjustment
of the travel sensor. If
this problem occurs
during normal
operation, the most
likely cause is a failure
of the travel sensor.
To correct,
1) Insure proper
mounting and linkage
adjustment.
2) Inspect and test
travel sensor
3) Toggle the
transducer target
mode.
If the problem persists,
replace the printed
wiring board (PWB)
assembly.
Output Press Sensor

(Sensors)
(Maintenance)
Port A Pressure
Sensor (Enabled)

the sensor.
Port B Pressure
Sensor (Enabled)
Supply Press Sensor
(Sensors)
(Advisory)
Supply Press
Sensor (Enabled)

fixed. Out of service results in
the actuator being at the No
Power condition.
Confirm proper
air supply
If it is verified that the

air supply is ok, replace
the printed wiring
board (PWB) assembly.
None - Indicates a possible

hardware problem that would
degrade diagnostic capability.
the sensor.

degrade diagnostic capability.
The pressure sensor

onboard the device
has failed. This may be
due to excessive supply
pressure or
contaminated air.
Confirm proper
air supply
The pressure sensor

onboard the device
has failed. This may be
due to excessive supply
pressure or
contaminated air.
If it is verified that the
air supply is ok, replace
the printed wiring
board (PWB) assembly.
Temperature Sensor
(Sensors)
(Advisory)
Temperature
Sensor (Enabled)
The temperature sensor

reading is outside the
functional range of the sensor.

degrade instrument calibration
and diagnostic capability.
Replace PWB
assembly.
The temperature
sensor onboard the
device has failed or the
unit has been exposed
to an temperature
extreme beyond the
recommended limits.
-Continued-
283
Instruction Manual
PlantWeb Alerts
August 2012
D103412X012

PlantWeb Alert
(Group)
Alert Condition
(Default)
Recommended
Action
Help
Pressure Fallback
(Sensors)
(Maintenance)
Pressure Fallback
(Enabled)
A travel sensor failure or large

travel deviation has resulted in
fallback to pressure control.
None - Indicates a reduced

performance condition.
Check instrument
feedback linkage
and travel sensor.
The instrument has

detected that the travel
sensor is outside its
normal range of
operation or that a
gross deviation exists
between set point and
actual travel. It has
switched to Pressure
Control and is no
longer using the travel
sensor to position the
valve.
Supply Pressure
(Environment)
(Maintenance)
Supply Press High

(Enabled)
The supply pressure has

exceeded the Supply Pressure
Hi Alert Point.
None - Indicates a condition

that could cause damage to
the instrument or actuator.
Confirm proper
air supply.
The Supply Pressure

sensor onboard has
detected an abnormally
high supply pressure.
Verify the proper
supply pressure and
that the alert is
properly set.
Supply Press Low

(Enabled)
The supply pressure is lower

than the Supply Pressure Lo
Alert Point.

that could reduce performance
or prevent the valve from
shutting tightly.
Temperature High
(Enabled)
The temperature is greater

than the Temperature Hi Alert
Point.

that could shorten service life
or lead to reduced
performance.
Temperature Low
(Enabled)
The temperature is lower than

the Temperature Lo Alert
Point.
Temperature Limit
(Environment)
(Advisory)
-Continued-
284
The Supply Pressure

sensor onboard has
detected an abnormally
low supply pressure.
Verify the proper
supply pressure and
that the alert is
properly set.
Check instrument
environment.
The instrument
temperature has
exceeded the user
configured high
temperature limit.
Operation of the
instrument above the
rated temperature may
degrade instrument
components. This may
affect instrument
performance and/or
reduce the life of the
instrument.
The instrument
temperature has
dropped below the user
configured low
temperature limit.
Operation of the
instrument below the
rated temperature may
degrade instrument
components. This may
affect instrument
performance and/or
reduce the life of the
instrument.
Instruction Manual
PlantWeb Alerts
D103412X012
August 2012

PlantWeb Alert
(Group)
Travel Deviation
(Travel)
(Maintenance)
Alert Condition
(Default)
Travel Deviation
(Enabled)
The Travel Deviation has

exceeded the Travel Deviation
Alert Point by more than the
Travel Deviation Time.
None - Indicates a reduced

performance condition.
Recommended
Action
Check valve
friction, supply
air, instrument
tuning
Help
The valve travel is not
following setpoint.
Check operation of the
valve and instrument.
Possible items include;
sticking valve, low
supply pressure,
broken feedback
linkage, instrument
pneumatic
components, actuator,
instrument tubing,
poor instrument
tuning, etc.
Test the control valve
assembly for proper
operation. ValveLink
software diagnostics
can be used for this
purpose.
Travel Limit
(Travel)
(Advisory)
Travel Limit Hi Hi
(Disabled)

Travel Limit Hi Hi Alert Point.
None
Check process
loop
Travel Limit Lo Lo
(Disabled)

Travel Limit Lo Lo Alert Point.
None
Check process
loop
N/A
(Travel)
(N/A)
Travel Limit Hi
(Disabled)

Travel Limit Hi Alert Point.
None
Check process
loop
The actual valve

position has exceeded
the configurable travel
limit (in %).
Travel Limit Lo
(Disabled)

Travel Limit Lo Alert Point.
None
Check process
loop
The actual valve

limit (in %).
Travel Open
(Disabled)

Open Alert Point
None
Check process
loop
The actual valve

position is near the full
open position.
Travel Closed
(Disabled)

Closed Alert Point
None
Check process
loop
The actual valve

position is near the full
closed position.
Proximity Hi Hi
(Disabled)
The Travel is within the

configured band of the
configured center point.
None
Check process
loop
The actual valve

position is near the
configured center
point.
N/A
(Proximity)
(N/A)
Proximity Hi
(Disabled)
None
Proximity Lo
(Disabled)
None
Proximity Lo Lo
(Disabled)
None
The actual valve

limit (in %).
Cycle Counter
(Travel History)
(Maintenance)
Cycle Counter
(Disabled)
The number of travel reversals

has exceeded the configured
limit.
None
Perform periodic
maintenance
The cycle count limit

has been exceeded.
Perform periodic
maintenance. Check
packing, linkages,
diaphragms, seals, etc.
Travel Accumulator
(Travel History)
(Maintenance)
Travel
Accumulator
(Disabled)
The accumulated travel has

exceeded the configured limit.
None
Perform periodic
maintenance
The travel accumulator

limit has been
exceeded. Perform
periodic maintenance.
Check packing,
linkages, diaphragms,
seals, etc.
-Continued-
285
Instruction Manual
PlantWeb Alerts
August 2012
D103412X012

PlantWeb Alert
(Group)
Alert Condition
(Default)
Recommended
Action
Help
(Performance)
(Failed)
Performance
Critical
(Enabled)
Critical performance issues

None - Indicates control has

been lost or severely reduced.
Check I/P, Relay,

Valve, Actuator
or Ext. Tubing as
indicated.
Onboard diagnostics
have detected a critical
performance issue that
may result in loss of
control or severe
reduction in control
performance. Check or
replace the component
indicated in the
possible cause detail.
Performance Reduced
(Performance)
(Maintenance
Performance
Reduced (Enabled)
Reduced performance issues

None - Indicates reduced

performance.
Check I/P, Relay,

Valve, Actuator
or Ext. Tubing as
indicated.
Onboard diagnostics
have detected a
performance issue that
has reduced control
performance. Check or
replace the component
indicated in the
possible cause detail.
(Performance)
(Advisory)
Performance
Information
(Enabled)
None - Indicates information

that may pertain to control
performance.
No action
required.
Onboard diagnostics
have detected an
abnormal performance
condition. No
immediate action
required.
Table C4. Output Block PV Status

FEATURE_SEL
PW Alarms Set PV Status
Enabled
Not Enabled
Transducer Mode,
Actual
Active PlantWeb
Alarms
AO / DO
PV Status
AO / DO PV
Substatus
AO/DO PV Limit Substatus(1)
OOS
Bad
Device Failure
Constant
Man
Bad
Nonspecific
Constant
Auto
Fail
Uncertain
Subnormal
See table C5
Auto
Maint, no Fail
Uncertain
Nonspecific
See table C5
Auto
Advisory, no Fail, no Maint
Good
Advisory
See table C5
Auto
None
Good
NonSpecific
See table C5
OOS
Bad
Device Failure
Constant
Man
Bad
NonSpecific
Constant
Auto
Fail
Good
NonSpecific
See table C5
Auto
Maint, no Fail
Good
NonSpecific
See table C5
Auto
Advisory, no Fail, no Maint
Good
NonSpecific
See table C5
Auto
None
Good
NonSpecific
See table C5
NOTES:
X = No Effect
1. PV limit substatus reflects only READBACK limit substatus. SP limit substatus reflects only out block rate limits.
Table C5. Limit Sub Status

Out Block
Transducer Mode
In Cutoff Region
Rate Limited
Limit SubStatus
AO, DO
OOS
Constant
AO, DO
MAN
Constant
AO
AUTO
High
High Limited
AO
AUTO
Low
Low Limited
AO
AUTO
High
High Limited
AO
AUTO
Low
Low Limited
AO
AUTO
None
None
Not Limited
DO
AUTO
High
High Limited
DO
AUTO
Low
Low Limited
DO
AUTO
None
Not Limited
NOTE: X = No Effect
286
Instruction Manual
FOUNDATION fieldbus Communication
D103412X012
August 2012
Appendix D FOUNDATION fieldbus Communication9DD

DVC6200f digital valve controllers use the FOUNDATION fieldbus to communicate with other fieldbus instruments and
the control system. Fieldbus is an all digital, serial, twoway communication system which interconnects field
equipment such as transmitters, digital valve controllers, and process controllers. Fieldbus is a localarea network
(LAN) for instruments used in both process and manufacturing automation with builtin capability to distribute the
control application across the network.
Function Block Overview

A fieldbus system is a distributed system composed of field devices and control and monitoring equipment integrated
into the physical environment of a plant or factory. Fieldbus devices work together to provide I/O and control for
automated processes and operations. The Fieldbus Foundation provides a framework for describing these systems as a
collection of physical devices interconnected by a fieldbus network. One of the ways that the physical devices are used
is to perform their portion of the total system operation by implementing one or more function blocks.
Function Blocks
Function blocks within the fieldbus device perform the various functions required for process control. Because each
system is different, the mix and configuration of functions are different. Therefore, the Fieldbus Foundation has
designed a range of function blocks, each addressing a different need: Analog Input Block (AI), Multiple Analog Input
(MAI), Discrete Input Block (DI), Manual Loader Block (ML), Bias/Gain Station Block (BG), Control Selector Block (CS), P,
PD Controller Block (PD), PID, PI, I Controller Block (PID), Ratio Station Block (RA), Analog Output Block (AO) and
Discrete Output Block (DO).
Function blocks perform process control functions, such as analog input (AI) and analog output (AO) functions as well
as proportionalintegralderivative (PID) functions. The standard function blocks provide a common structure for
defining function block inputs, outputs, control parameters, events, alarms, and modes, and combining them into a
process that can be implemented within a single device or over the fieldbus network. This simplifies the identification
of characteristics that are common to function blocks.
The Fieldbus Foundation has established the function blocks by defining a set of parameters used in all function blocks
called universal parameters. The Fieldbus Foundation has also defined a standard set of function block classes, such as
input, output, control, and calculation blocks. Each of these classes have a set of parameters established for it.
Additionally, they have published definitions for transducer blocks commonly used with standard function blocks.
Examples include temperature, pressure, level, and flow transducer blocks.
Fieldbus Foundation specifications and definitions allow vendors to add their own, extended parameters, as well as
their own algorithms. This approach permits extending function block definitions as new requirements are discovered
and as technology advances.
Each block has a tag name. Service personnel need only know the tag name of the block to access or change the
appropriate block parameters.
Input events may affect the operation of the algorithm. An execution control function regulates the receipt of input
events and the generation of output events during execution of the algorithm. Upon completion of the algorithm, the
data internal to the block is saved for use in the next execution, and the output data is snapped, releasing it for use by
other function blocks.
Once the inputs are snapped, the algorithm operates on them, generating outputs as it progresses. Algorithm
executions are controlled through the setting of internal parameters. Internal parameters do not appear as normal
input and output parameters. However, they may be accessed and modified remotely, as specified by the function
block.
287
Instruction Manual

August 2012
D103412X012
Figure D1 illustrates the internal structure of a function block. When execution begins, input parameter values from
other blocks are snappedin by the block. The input snap process ensures that these values do not change during the
block execution. New values received for these parameters do not affect the snapped values and will not be used by
the function block during the current execution.
Function blocks are also capable of performing shortterm data collection and storage for reviewing their behavior.
InstrumentSpecific Blocks
In addition to function blocks, fieldbus devices contain two other block types to support the function blocks. These are
the resource block and the transducer block. The resource block contains the hardware specific characteristics
associated with a device. Transducer blocks couple the function blocks to local input/output functions.
Figure D1. Function Block Internal Structure
Input Parameter
Linkages
Input
Events
Execution Control
Input
Snap
Processing
Algorithm
status
Output
Events
Output
Snap
Output
Parameter
Linkages
status
B2711
Resource Blocks
The resource block contains hardware specific characteristics associated with the device; it has no input or output
parameters. The algorithm within a resource block monitors and controls the general operation of the physical device
hardware. The execution of this algorithm is dependent on the characteristics of the physical device, as defined by the
manufacturer. As a result of this activity, the algorithm may cause the generation of events. There is only one resource
block defined for a device. For example, placing the resource block in Out of Service mode stops all function block
execution, by setting their modes to Out of Service as well. The actual mode of the function blocks is changed to Out
of Service, but the function block target modes will not change. Placing the resource block in the Out of Service mode
does not affect the mode of the transducer block.
Transducer Blocks
Transducer blocks connect function blocks to local input/output functions. They read sensor hardware and write to
effector (actuator) hardware. This permits the transducer block to execute as frequently as necessary to obtain good
data from sensors and ensure proper writes to the actuator without burdening the function blocks that use the data.
The transducer block also isolates the function block from the specific characteristics of the physical I/O.
288
Instruction Manual
D103412X012
August 2012
Block Modes
All blocks have modes. The mode determines the source of the set point, the destination of the output, how the block
executes, and the relationship between setpoint and output. The block mode is determined by the Block Mode
parameter. It is a structured parameter composed of the attributes actual, target, permitted, and normal. The
following defines each of the attributes.
Target modeThe Target mode is the mode requested by the user or host system. Only one mode is allowed to be
set and it must be a permitted mode as defined by the permitted attribute of the mode parameter.
Actual modeThis is the current mode of the block. The actual mode may differ from the target mode due to
operating conditions of the block.
Permitted modeThe permitted mode defines the modes allowed for the block. This is set by the user or host
system but is restricted by the instrument to modes supported by the instrument for the particular block. Any
change request to the Target or Normal attribute is checked against the permitted attribute to ensure the
requested mode is permitted.
When setting the Permitted mode, there is no check against any of the other attributes (Normal or Target modes).
Therefore, the normal or target mode attributes may have a value that is not permitted because the permitted
attribute was modified after the Normal or Target mode was set. This will have no effect on the instrument until the
user attempts to modify the Target or Normal mode. At this time these attributes are tested against the Permitted
modes, thus the user cannot change the Normal or Target modes to what was formerly permitted.
Normal modeThe normal mode is the mode the block should be in during normal operating conditions. The
normal mode is set by the user or host system and can only be set to a permitted mode (see permitted mode). The
user or host system can compare the actual mode to the normal mode and, based on the results, determine if the
block is operating normally.
Table D1 lists the modes supported by each block contained in the digital valve controller.
Table D1. DVC6200f Block Modes
Block
Resource
Transducer
Supported Mode Values

Auto and OOS
Auto, Manual, and OOS
AO
RCas, Cas, Auto, Man, LO(1), IMan(1), and OOS
PID
ROut, RCas, Cas, Auto, Man, LO(1), IMan(1), and OOS
ISEL
Auto, Man and OOS
OS
IMan(1), Auto, Cas and OOS
AI
Man, Auto, and OOS
MAI
Man, Auto, and OOS
DO
RCas, Cas, Auto, Man, LO(1), IMan(1), and OOS
DI
Auto, Man, and OOS
1.This mode cannot be specified as a target mode.
Changing the block mode requires accessing the Block Mode parameter. For information on using the host system to
change the block mode via this parameter, see the appropriate host documentation.
289
Instruction Manual

August 2012
D103412X012
Note
A downstream block changing to Out of Service impacts the mode of the upstream block. Refer to the block hierarchy in
figure D2.
Figure D2. Digital Valve Controller Block Hierarchy Example
RESOURCE BLOCK
PID BLOCK
ANALOG OUTPUT
(AO) BLOCK
TRANSDUCER
BLOCK
NOTES:
1.CHANGING THE RESOURCE BLOCK TO OUT OF SERVICE CHANGES ALL FUNCTION BLOCKS
TO OUT OF SERVICE, BUT DOES NOT AFFECT THE TRANSDUCER BLOCK.
2.CHANGING A DOWNSTREAM BLOCK TO OUT OF SERVICE AFFECTS THE UP STREAM BLOCK.
FOR EXAMPLE: WHEN THE TRANSDUCER BLOCK IS OUT OF SERVICE, THE AO BLOCK MODE
WILL CHANGE TO IMAN (INITIALIZE MANUAL).
Note
There is no mode associated with the FOUNDATION fieldbus Loop. Mode is dependent on the blocks within the Loop.
Explanation of Modes
Out of Service (OOS)The functions performed by the block are not executed. If the block has any outputs, these
typically do not update and the status of any values passed to downstream blocks will be BAD. To make changes to
some of the parameters in a block requires that the block be Out of Service.
Initialization Manual (IMan)Only the AO, DO, OS and PID blocks support this mode. When one of these blocks
detects a loss of a correct path to the downstream block (such as when the downstream block is in the OOS, Man, or
LO mode), it enters the IMan mode. For example, when the transducer block enters the OOS mode, the AO block
enters the IMan mode.
Local Override (LO)Only the AO, DO, and PID blocks support this mode. If the PID block enters the LO mode, the
block output follows the tracking value (TRK_VAL), if external tracking is enabled by TRK_IN_D. In the AO and DO
block, the block enters LO mode when the block detects that fault state is active. In this case, the output is determined
by the selection for I/O_OPTS.
Manual (Man)If the data status of a function block's input is bad or its target mode is Man, the block enters the
manual mode. In this mode, the function block does not update its OUT value. If the target is Man, the user may write
a desired value to the output.
Automatic (Auto)The block performs the specified calculations based on the local set point and outputs the result,
independently without interfacing with another block. The user can write to the set point of a block in this mode. Any
block outputs continue to update.
Cascade (Cas)The block performs the specified calculations based on the set point from another block via the
cascade input parameter and outputs the result. Any block outputs continue to update.
290
Instruction Manual
D103412X012
August 2012
Remote Output (ROut)The block outputs are set to the value of the remote output parameter that is written by a
host computer or others. To prevent a sudden change in output, the block's calculations are initialized when a change
in mode occurs.
Remote Cascade (RCas)The block performs the specified calculations based on a set point from a host computer or
others via the remote cascade input and outputs the result. If the block has any outputs, these continue to update.
Examples of Modes for Various Operational Statuses

Table D2 shows examples of block mode combinations in a digital valve controller (however it does not show all
combinations). When a block changes mode or the data status signal changes for some reason, the other blocks
connected to that block identify the change by detecting the change in status of an input signal, and change their
modes too. For example, when the data status of BKCAL_IN in a PID block changes to bad, the PID block automatically
changes its mode to Iman to initialize the control of its downstream block.
Table D2. Examples of Block Mode Combinations and Operational statuses for an Instrument with Standard Control
Operational Status
Blocks
TB(1)
PID
AO
Initial Setup and calibration
---
OOS
OOS
Modification of some transducer block parameters
---
IMan
Manual
Constant valve position control

PID Singleloop control
PID Cascadeloop control
---
Auto
Auto
Auto
Cas
Auto
Primary PID, Auto

Secondary PID, Cas
Cas
Auto
1.TB=Transducer Block
The respective modes to which each block should enter upon occurrence of a communication error and at a restart,
and the handling of signals in each mode may be defined in the block's option parameters such as IO_OPTS and
STATUS_OPTS. For details, see the detailed descriptions of each function block.
Device Descriptions
Device Descriptions are specified definitions that are associated with blocks. Device descriptions provide for the
definition and description of blocks and their parameters.
Device descriptions may also include a set of processing routines called Methods. Methods provide a procedure for
accessing and manipulating a series of parameters within a device, such as for setup and calibration. Methods are used
for a variety of functions including automatic calibration, setting protection and setting up the instrument. These
Methods are a predetermined sequence of steps for information required to setup, calibrate, and perform other
functions on the instrument.
Transducer Block Status and Limit Propagation

Every FOUNDATION fieldbus parameter has a value and a status. The status attribute is divided into three components:
Quality, Quality substatus, and a Limit. The Quality can be Good (Cascade), Good (NonCascade), Uncertain, and Bad.
Each quality can have a substatus as shown in table D3. Each status attribute also has four possible limit states: Not
limited, Low limited, High limited, and Constant. Refer to the Fieldbus Foundation specifications for a more detailed
description. The following describes how the transducer block passes status information to the AO block. For
information on status handling by the function blocks within the digital valve controller, refer to the Detailed Setup
section.
291
Instruction Manual

August 2012
D103412X012
Table D3. Status Attribute Quality and Substatus Components

Quality
Substatus
Good (NC)
Nonspecific
Good (NC)
Active Block Alarm
Good (NC)
Active Advisory Alarm
Good (NC)
Active Critical Alarm
Good (NC)
Unack Block Alarm
Good (NC)
Unack Advisory Alarm
Good (NC)
Unack Critical Alarm
Uncertain
Nonspecific
Uncertain
Last Usable Value
Uncertain
Substitute/Manual Entry
Uncertain
Initial Value
Uncertain
Sensor Conversion not Accurate
Uncertain
Engineering Unit Range Violation
Uncertain
Subnormal
Good (C)
Nonspecific
Good (C)
Initialization Acknowledge
Good (C)
Initialization Request
Good (C)
Not Invited
Good (C)
Not Selected
Good (C)
Local Override
Good (C)
Fault State Active
Good (C)
Initiate Fault State
Bad
Nonspecific
Bad
Configuration Error
Bad
Not Connected
Bad
Device Failure
Bad
Sensor Failure
Bad
No Comm, with LUV
Bad
No Comm, no LUV
Bad
(NC)=(Noncascade)
Out of Service
(C)= (Cascade)
Status Propagation
The transducer block accepts the output from the AO block or DO block if the output parameter status is Good
(Noncascade) or Good (Cascade). When the AO or DO block is Out of Service the output parameter status is Bad. In
this case, the transducer block holds the last value.
If the transducer block actual mode is Out of Service, the AO block READBACK parameter status is Bad-Out of Service.
This could be caused by a Failed Alert. If a Failed Alert is active, the block error parameter (parameter name
BLOCK_ERR) for the Resource block will indicate Device Needs Maintenance Now. For more information on the
Resource and Transducer block error indications, refer to the Viewing Device Information section of this manual.
If the transducer block is functioning correctly the AO block READBACK parameter status is Good
(Noncascade)-Nonspecific. If a Maintenance or Advisory alert is active the substatus will reflect a Unacknowledged or
Active advisory alert. When a Maintenance or Advisory alert is active, the block error for the resource block indicates
Device Needs Maintenance Soon.
Limit Propagation
The following describes limit propagation:
292
Instruction Manual
D103412X012
August 2012
AO Block
If the valve position is below the low cutoff value, the AO block READBACK status limit is LOW_LIMITED.
If the valve position is above the high cutoff value, the AO block READBACK status limit is HIGH_LIMITED.
If the transducer block actual mode is Auto and the above conditions are not true, the AO block READBACK status
limit is NOT_LIMITED.
If the transducer block actual mode is Out of Service, the AO block READBACK status limit is CONSTANT.
DO Block
If the transducer block actual mode is Auto, the DO block READBACK_D status is NOT_LIMITED.
If the transducer block actual mode is Out of Service, the DO block READBACK_D status is CONSTANT.
The control strategy should be configured to monitor the Analog Output block status and take action where
appropriate when the status is no longer Good.
Network Communication
Figure D3 illustrates a simple fieldbus network consisting of a single segment.
Figure D3. Simple SingleLink Fieldbus Network
LAS
Fieldbus Segment
LINK MASTER
BASIC DEVICES
LAS = Link Active Scheduler
B27121
Device Addressing
Fieldbus uses addresses between 0 and 255. Addresses 0 through 15 are typically reserved for group addressing and
for use by the data link layer. If there are two or more devices with the same address, the first device to start will use its
programmed address. Each of the other devices will be given one of four temporary addresses between 248 and 251. If
a temporary address is not available, the device will be unavailable until a temporary address becomes available.
Commission devices use addresses 20-35, and standby devices use addresses 232247.
Link Active Scheduler (LAS)

There is only one active Link Active Scheduler (LAS) for the entire fieldbus control system. The digital valve controller
includes an LAS. The Link Active Scheduler operates as the bus arbiter for the link, and
293
Instruction Manual
August 2012
D103412X012
recognizes and adds new devices to the link.

removes nonresponsive devices from the link.
distributes Data Link (DL) and Link Scheduling (LS) time on the link. Data Link Time is a networkwide
time periodically distributed by the LAS to synchronize all device clocks on the bus. Link Scheduling time is a
linkspecific time represented as an offset from Data Link Time. It is used to indicate when the LAS on each link begins
and repeats its schedule. It is used by system management to synchronize function block execution with the data
transfers scheduled by the LAS.
polls devices for process loop data at scheduled transmission times.
distributes a prioritydriven token to devices between scheduled transmissions.
The DVC6200f can be designated to act as the backup Link Active Scheduler (LAS) in the event that the LAS is
disconnected from the segment. As the backup LAS, the DVC6200f will take over the management of
communications until the host is restored. The host system may provide a configuration tool specifically designed to
designate a particular device as a backup LAS. Otherwise, this can be configured manually as follows:
1. Access the Management Information Base (MIB) for the DVC6200f.
2. To activate the LAS capability, write 0x02 to the BOOT_OPERAT_FUNCTIONAL_CLASS object (Index 605). To
deactivate, write 0x01.
Restart the processor.
Only one device can communicate at a time. Permission to communicate on the bus is controlled by a centralized
token passed between devices by the LAS. Only the device with the token can communicate. The LAS maintains a list
of all devices are a member of the bus. This list is called the Live List.
Two types of tokens are used by the LAS. A timecritical token, compel data (CD), is sent by the LAS according to a
schedule. A nontime critical token, pass token (PT), is sent by the LAS to each device in numerical order according to
address.
Device Communication
Scheduled Transfers
Information is transferred between devices over the fieldbus using three different types of communication:
Publisher/Subscriber: This type of communication is used to transfer critical process loop data, such as the process
variable. The data producers (publishers) post the data in a buffer that is transmitted to the subscriber (S), when the
publisher is issued the Compel Data (CD) message from the LAS. The buffer contains only one copy of the data. New
data completely overwrites previous data. Updates to published data are transferred simultaneously to all
subscribers in a single broadcast. Transfers of this type are scheduled on a precisely periodic basis.
Figure D4 diagrams the method of scheduled data transfer. Scheduled data transfers are typically used for the regular
cyclic transfer of process loop data between devices on the fieldbus. Scheduled transfers use publisher/subscriber type
of reporting for data transfer. The Link Active Scheduler maintains a list of transmit times for all publishers in all devices
that need to be cyclically transmitted. When it is time for a device to publish data, the LAS issues a Compel Data (CD)
message to the device. Upon receipt of the CD, the device broadcasts or publishes the data to all devices on the
fieldbus. Any device that is configured to receive the data is called a subscriber.
294
Instruction Manual
D103412X012
August 2012
Figure D4. Scheduled Data Transfer

Host System
LAS
Schedule
X
Y
Z
DT(A )
CD (X, A)
LAS=Link Active Scheduler

P=Publisher
S=Subscriber
CD=Compel Data
DT=Data Transfer Packet
Device X
Device Y
Device Z
B27131
Unscheduled Transfers
Figure D5 diagrams an unscheduled transfer. Unscheduled transfers are used for things like userinitiated changes,
including set point changes, mode changes, tuning changes, and upload/download. Unscheduled transfers use either
report distribution or client/server type of reporting for transferring data.
Figure D5. Unscheduled Data Transfer
Host System
LAS
PT (Z)
Schedule
X
Y
Z
LAS=Link Active Scheduler

P=Publisher
S=Subscriber
PT=Pass Token
M=Message
Device X
M
S
Device Y
Device Z
B27141
All of the devices on the fieldbus are given a chance to send unscheduled messages between transmissions of
scheduled data. The LAS grants permission to a device to use the fieldbus by issuing a pass token (PT) message to the
device. When the device receives the PT, it is allowed to send messages until it has finished or until the maximum
token hold time has expired, whichever is the shorter time. The message may be sent to a single destination or to
multiple destinations.
295
Instruction Manual

August 2012
D103412X012
Report Distribution: This type of communication is used to broadcast and multicast event and trend reports.
Client/Server: This type of communication is used for request/ response exchanges between pairs of devices, such
as a set point change. Like Report Distribution reporting, the transfers are queued, unscheduled, and prioritized.
Queued means the messages are sent and received in the order submitted for transmission, according to their
priority, without overwriting previous messages.
Function Block Scheduling

Figure D6 shows an example of a link schedule. A single iteration of the linkwide schedule is called the macrocycle.
When the system is configured and the function blocks are linked, a master linkwide schedule is created for the LAS.
Each device maintains its portion of the linkwide schedule, known as the Function Block Schedule. The Function Block
Schedule indicates when the function blocks for the device are to be executed. The scheduled execution time for each
function block is represented as an offset from the beginning of the macrocycle start time.
Figure D6. Example Link Schedule Showing Scheduled and Unscheduled Communication
Start of Next Macrocycle
Macrocycle Start Time
Offset from macrocycle
start time = 0 for AI Execution
Device 1
Sequence Repeats
AI
AI
start time = 20 for AI
Communication
Scheduled
Communication
Unscheduled
Communication
start time = 30 for AI
Execution
Device 2
PID
AO
PID
AO

start time = 50 for AO
Communication
B27151
20
40
60
80
100
120
20
40
60
80
100
120
Macrocycle
To support synchronization of schedules, periodically Link Scheduling (LS) time is distributed. The beginning of the
macrocycle represents a common starting time for all Function Block schedules on a link and for the LAS linkwide
schedule. This permits function block executions and their corresponding data transfers to be synchronized in time.
Network Management
Information for setting up network communications, including Virtual Communication Relationships (VCRs), host
timer recommendations, and other network parameters, can be found in the capabilities file (.cff) available from the
website www.FIELDVUE.com or from the Fieldbus Foundation website.
296
Instruction Manual
Device Description Installation
D103412X012
August 2012
Appendix E Device Description Installation10EE

Overview
Several support files are required for the DVC6200f digital valve controller. They are:
Device Description (DD) filesThese files define the data interface to the digital valve controller (file extensions
.sym and .ffo).
Capabilities FileThese files allow a host to configure the control system offline (e.g., without having a device
physically attached to the host) (file extension .cff).
DeltaV Registry FileThis file is used by DeltaV to define the device interface (file extension .reg)
DeltaV fhx FileThis file is used by DeltaV to define the device and the data interface to the device (file extension
.fhx).
DeltaV Windows Resource FileThese files define the user interface for the device for DeltaV and include the
definitions for the transducer block interface and the resource block interface (file extension .dll).
The directory structure defined by the Fieldbus Foundation for device descriptions is as follows:
....\xxxxxx\yyyy\rrddcc.eee
where:
....\
is the path to the DD structure as implemented by the host system. This is typically defined as the base path
to the DD since access to the specific device DD is predefined from the base folder. For a DeltaV system, the
DDs are included with the support files and are located in a folder named amsdevices. For other hosts, the
Fieldbus Foundation defines a folder named release that is included with the CDROM, however, you do not
need to retain this folder name.
xxxxxx is the 6digit hexadecimal equivalent of the manufacturer's identification number as defined by the Fieldbus
Foundation. Fisher Controls' ID number is 5100 (or in the folder format 005100). This number is also stored in
the instrument Resource Block in the parameter Mfg ID (parameter name MANUFAC_ID).
yyyy
is the 4digit hexadecimal equivalent of the device type, as defined by the manufacturer. For example, the
device type for the DVC6200f digital valve controller is 4602. This number is stored in the instrument
Resource Block in the parameter Device Type (parameter name DEV_TYPE).
rr
is the 2digit hexadecimal equivalent of the device revision, as defined by the manufacturer. It is stored in the
instrument Resource Block in the parameter Device Revision (parameter name DEV_REV).
dd
is the 2digit hexadecimal equivalent of the device description (DD) revision that applies to the device, as
defined by the manufacturer. The host will always use the latest version of the DD that it finds for a particular
device revision. When part of the name of a capabilities file, this value is always the same as the value of the
DD_REV parameter stored in the Resource Block of the instrument. The value of the DD_REV parameter
represents the earliest version of the DD that is compatible with the device revision of the instrument.
cc
is a 2digit hexadecimal equivalent for the capabilities files (.cff) revision, as defined by the manufacturer. The
latest revision of the capabilities files, for a particular device revision, is the file with the largest value for this
number.
eee
is the file extension. At this time, five extensions exist for files, they are:
.symThis extension denotes a device description (DD) symbol file as defined by the Fieldbus
Foundation.
297
Instruction Manual
August 2012
D103412X012
.ffoThis extension denotes a complete, tokenized, device description for the instrument as defined by
the Fieldbus Foundation.
.cffThis extension denotes a capabilities file for the instrument as defined by the FOUNDATION Fieldbus
Common File Format specification.
.fhxThis extension denotes a DeltaV device definition file.
.dllThis extension denotes a windows resource file used by DeltaV.
.regThis extension denotes a DeltaV registry file.
.almThis extension denotes a DeltaV alarm file (DeltaV version 6 only).
Device Description and Methods

FOUNDATION fieldbus technology uses Device Descriptions (DD) and function blocks to achieve interoperability
between instruments and control systems or hosts from various manufacturers. The DD provides information to
describe the data interface to the device.
The following table describes the compatibility between the DVC6200f firmware revisions and DD revisions.
Device Description Compatibility
Firmware Revision
2.0
DD Compatibility
2 and 3
For fieldbus devices, in addition to providing parameter definitions and other information required by the control
system to communicate with the fieldbus device, the DD may also include methods. Methods can be used for a variety
of functions including automatic calibration, setting protection, setting up the instrument, etc. These methods are a
predetermined sequence of steps for information required to setup, calibrate, and perform other functions on the
instrument. How the method prompts the user, and how messages appear is determined by the host system. For
information on using methods on the host system see the appropriate host system documentation.
Table E1 contains the methods available in the DVC6200f, the block it is found in, and the page number where it is
described.
Installing DD on a DeltaV ProfessionalPLUS Workstation

The following is general information that may apply when installing the DD on a DeltaV system during the Add Device
Definition procedure. This procedure is accessed from the DeltaV/Library, as shown in figure E1. For complete
information, refer to the DeltaV documentation.
Figure E1. Add Device Definition
298
Instruction Manual
D103412X012
August 2012
Note
Before beginning the Add Device Definition procedure, it is recommended that the Add Device Utility be installed on DeltaV. This
may help prevent installation errors from occurring.
Table E1. Methods

Method
Block
Description Location
Auto Calibration
Transducer
page 214
Block Error Reporting
Transducer
page 86
Transducer
page 62
Resource
page 45
Display DD Version
Resource
page 301
Instrument Alerts
Transducer
page 69
Manual Travel Calibration
Transducer
page 214
Output A Sensor Calibration
Transducer
page 217
Output B Sensor Calibration
Transducer
page 217
PlantWeb Alerts
Transducer
page 69
Relay Adjust
Transducer
page 215
Reset Options
Resource
page 221
Device Setup
Transducer
page 40
Stabilize/Optimize
Transducer
page 64
Stroke Valve
Transducer
page 228
Supply Sensor Calibration
Transducer
page 216
Define Custom Characteristic
Transducer
page 68
Travel Deviation Fallback
Transducer
page 67
Outblock Selection
Transducer
page 69
Transducer
page 86
Performance Tuner
Transducer
page 44, 64
Block Mode
Note
Be sure to select the correct DD for the DeltaV revision being used. The resource files are different for each revision of DeltaV.
Device descriptions furnished by Fisher contain only those files applicable to Fisher. All the files are located in the
manufacturer ID Folder (005100 for xxxxxx in directory structure above). A readme file is included at the top level.
Read this file for any additional information regarding DD installation.
Device descriptions furnished by the Fieldbus Foundation (on CDROM or diskette) contain the files for each
registered manufacturer and their associated device(s). It is placed on the media starting with the release folder,
which then contains a folder (xxxxxx) for each manufacturer as defined above. For Fisher this folder is 005100. A
readme file may be included at the top level. Read this file for any additional information regarding the DD.
For the DVC6200fThe device type parameter for this unit is 4602. This device includes the AO, PID, ISEL, OS, AI,
MAI, DO and DI function blocks. From DeltaV Explorer, select the amsdevices\005100\4602 folder (refer to
figure E2).
299

August 2012
Instruction Manual
D103412X012
Figure E2. amsdevices folder
The most recent device description for Fisher devices can be downloaded from the internet at www.FIELDVUE.com.
If you are downloading from the internet, the file on the website will be compressed (zipped) and must be
decompressed (unzipped) before proceeding. Refer to the website download and installation procedures for setting
up the DD on your system. Note the folder where the decompressed files are placed. This information will be
required later in the installation procedure.
Note
Record any warning/error messages from the message window in DeltaV Explorer so that it can be communicated to the DeltaV
Technical Support Group.
Installing DDs on Other Fieldbus Host Systems

The following is a generic procedure for installing the device descriptions on a host system. Refer to your host system
documentation for specific information. In general the following may apply:
Device descriptions furnished by Fisher contain only those files applicable to Fisher. All the files are located in the
manufacturer ID Folder (005100 for xxxxxx in directory structure above). A readme file is included at the top level.
Read this file for any additional information regarding DD installation.
Device descriptions furnished by the Fieldbus Foundation (on CDROM or diskette) contain the files for each
registered manufacturer and their associated device(s). It is placed on the media starting with the release folder,
which then contains a folder (xxxxxx) for each manufacturer as defined above. For Fisher this folder is 005100. A
readme file may be included at the top level. Read this file for any additional information regarding the DD.
For the DVC6200f Digital Valve ControllerThe device type parameter for this unit is 4602. This device includes the
AO, PID, ISEL, OS, AI, MAI, DO and DI function blocks. From Windows Explorer, select the release\005100\4602
folder.
The most recent device description for Fisher devices can be downloaded from the internet at www.fisher.com. If
you are downloading from the internet, the file on the website will be compressed (zipped) and must be
decompressed (unzipped) before proceeding. Refer to the website download and installation procedures for setting
300
Instruction Manual
D103412X012
August 2012
up the DD on your system. Note the folder where the decompressed files are placed. This information will be
required later in the installation procedure.
Note
This procedure will install the necessary Device Description files (*.ffo and *.sym), and Capabilities file (*.cff) for the device.
1. Locate or create the folder on the host system to contain all the DD and capabilities files.
If you are creating a folder, you can name this new folder whatever you would like and it can have any path you define.
For this installation procedure, this folder will be referred to as the base folder.
2. On the CDROM or in the website download files, locate the folder with the new support files. This folder is called
\RELEASE.
3. Open this folder and select the folder named 005100.
4. Copy the 005100 folder (and all its subfolders) from the CDROM or website download location to the base folder.
If this is an update (the folders already exist), the system informs you that the folders already exist and asks if they
should be replaced. Answer Yes or OK so the folders are properly updated.
5. The new support files are now installed. You may have to restart applications and drivers in order for the new files to
become active.
DD installation is complete. Consult the system documentation for commissioning new devices or updating existing
devices.
Displaying the Device Description Version

You can use the DD In Use method to display version information for the device descriptions installed on the system.
The DD in Use method is included with the device description (DD) software. For information on using methods, see
the host system documentation.
DD in Use displays the version number displayed in the format: device type.device revision.DD revision. The Min
Compatible DD revision displayed is the latest device description revision that is compatible with the displayed device
revision.
This method is available via the resource block.
301

August 2012
302
Instruction Manual
D103412X012
Instruction Manual
Operating with a DeltaV System
D103412X012
August 2012
Appendix F Operating with a DeltaV SystemFF

Process Systems DeltaV System
Getting Started with DeltaV Host Systems
Appropriate Device Descriptions (DDs) installed. See the Device Description Compatibility table on
page 298. For DD installation information see Appendix E.
Digital valve controller correctly mounted on actuator. For mounting information see the
Installation section of this manual and the instructions included with the mounting kit.
Utilities connected. For information on making pneumatic and electrical connections, see the
Installation section of this manual. For information on applying power to the segment, see DeltaV
books online.
Instrument in standby. For information on placing the instrument in standby, see DeltaV books
online.
Perform the initial setup. See the Basic Setup section of this manual. If the valve is shipped from the
factory mounted on an actuator, perform basic setup only to verify setup is correct and valve
operation is satisfactory.
Device Commissioned. For information on commissioning a device, see DeltaV books online.
Additional configuration required, such as setting alarms, cutoffs, and other resource block and
transducer block parameters. See the Detailed Setup section of this manual.
Control strategy defined. For information on defining a control strategy, see DeltaV books online.
Associate I/O with device. See DeltaV books online.

Download device. See DeltaV books online.
303
Instruction Manual

August 2012
D103412X012
Table F1. Transducer Block (TB) Parameters - Configuration Index

Parameter Label
Path to Parameter
Actual Travel
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Actual Travel
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Fail Action
Actuator Manufacturer ID
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Manufacturer ID
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Model Number
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Serial Number
Actuator Size
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Size
Actuator Style
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Actuator Style
Air
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Air
Alert Conditions
TB > Device Diagnostics > Alert Conditions
Alert Key
TB > Configure/Setup > Detailed Setup > Alerts > Configuration > Alert Key
Area Units
TB > Configure/Setup > Detailed Setup > Instrument > Units: Area Units
TB > Device Diagnostics > Status > Transducer Block Error: Block Configuration Error
Blocks Set to Default Alert
TB > Configure/Setup > Detailed Setup > Alerts > Configuration > Blocks Set to Default: Block Set to Default Alert
Blocks Set to Default Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Configuration > Blocks Set to Default: Block Set to Default Alert Enable
Calibration Date
TB > Configure/Setup > Detailed Setup > Instrument > Calibration: Calibration Date
TB > Configure/Setup > Detailed Setup > Instrument > Calibration: Calibration Location
Calibration Person
TB > Configure/Setup > Detailed Setup > Instrument > Calibration: Calibration Person
Cycle Count
TB > Configure/Setup > Detailed Setup > Alerts > Travel History > Cycle Counter:Cycle Count
TB > Device Variables > Overview > Cycle Count
Cycle Count Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel History > Cycle Counter: Cycle Count Alert
Cycle Count Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel History > Cycle Counter: Cycle Count Alert Enable
Cycle Count Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Travel History > Cycle Counter Cycle Count Alert Point
Cycle Count Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel History > Cycle Counter: Cycle Count Deadband
TB > Device Diagnostics > Status > Transducer Block Error: Device Needs Maintenance Now
Drive Current
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Drive Current: Drive Current
Drive Current Alert
TB > Device Diagnostics > Status > Self Test Status: Drive Current Alert
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Drive Current: Drive Current Alert
Drive Current Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Drive Current: Drive Current Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Drive Current: Drive Current Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Drive Current: Drive Current Alert Time
Drive Current Manual Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Drive Current: Drive Current Manual Recovery
Drive Current Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Drive Current: Drive Current Shutdown
Drive Signal
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Drive Signal: Drive Signal
TB > Device Variables > Overview > Drive Signal
Drive Signal Alert
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Drive Signal: Drive Signal Alert
Drive Signal Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Drive Signal: Drive Signal Alert Enable
Effective Area
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Effective Area
Feedback Connection
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Feedback Connection
Flow Direction
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Flow Direction
Flow Tends To
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Flow Tends To
I/O Processor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: I/O Processor Alert
I/O Processor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: I/O Processor Alert Enable
I/O Processor Manual Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: I/O Processor Man Recovery
I/O Processor Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: I/O Processor Shutdown
Inlet Pressure
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Inlet Pressure
TB > Configure/Setup > Detailed Setup > Response Control > Input Characterization > Input Characterization
TB > Device Variables > Overview > Input Characterization
TB > Device Diagnostics > Status > Self Test Status: Integrator Limited Hi
TB > Device Diagnostics > Status > Self Test Status: Integrator Limited Lo
TB > Device Diagnostics > Status > Self Test Status: Integrator Suspended
IOP Failure
TB > Device Diagnostics > Status > Self Test Status: IOP Failure
Last Valid Point
TB > Configure/Setup > Detailed Setup > Response Control > Input Characterization > Last Valid Point
Leak Class
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Leak Class
Length Units
TB > Configure/Setup > Detailed Setup > Instrument > Units: Length Units
-Continued-
304
Instruction Manual
D103412X012
August 2012
Table F1. Transducer Block (TB) Parameters - Configuration Index (Continued)

Parameter Label
Lever Style
Path to Parameter
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Lever Style
Lost Static Data
TB > Device Diagnostics > Status > Transducer Block Error: Lost Static Data
Lower Bench Set
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Lower Bench Set
MAI Channel 1
MAI Channel 2
MAI Channel 3
MAI Channel 4
MAI Channel 5
MAI Channel 6
MAI Channel 7
MAI Channel 8
Maximum Supp Pressure
TB > Configure/Setup > Detailed Setup > Instrument > Application: Max Supp Pressure
MLFB Error
TB > Device Diagnostics > Status > Self Test Status: MLFB Error
Moment Arm Length
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Moment Arm
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Nominal Supply Pressure
Out of Service
TB > Device Diagnostics > Status > Transducer Block Error: Out of Service
Outlet Pressure
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Outlet Pressure
TB > Configure/Setup > Detailed Setup > Alerts > Configuration > Output Block Timeout: Output Blk Timeout
TB > Configure/Setup > Detailed Setup > Alerts > Configuration > Output Block Timeout: Output Block Timeout Alert
Output Block Timeout Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Configuration > Output Block Timeout: Output Block Timeout Alert Enable
Output Block Timeout Manual

Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Configuration > Output Block Timeout: Output Block Timeout Manual Recovery
Output Block Timeout Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Configuration > Output Block Timeout: Output Block Timeout Shutdown
Packing Type
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Packing Type
PD Inside Status
TB > Configure/Setup > Detailed Setup > Alerts > Performance > PD Inside Status
PD Inside Status
TB > Device Variables > Overview > PD Inside Status
PD Run
TB > Configure/Setup > Detailed Setup > Alerts > Performance > PD Run
TB > Configure/Setup > Detailed Setup > Alerts > Performance > Performance Critical: Performance Critical Alert
TB > Configure/Setup > Detailed Setup > Alerts > Performance > Performance Critical: Performance Critical Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Performance > Performance Information: Performance Information Alert

Enable
TB > Configure/Setup > Detailed Setup > Alerts > Performance > Performance Information: Performance Information Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Performance > Performance Reduced: Performance Reduced Alert
Performance Reduced Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Performance > Performance Reduced: Performance Reduced Alert Enable
Performance Tuner(1)
Port Diameter
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Port Diameter
Port Type
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Port Type
Pressure A Sensor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Pressure Sensors: Pressure A Sensor Alert
Pressure A Sensor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Pressure Sensors: Pressure A Sensor Alert Enable
Pressure A Sensor Manual Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Pressure Sensors: Pressure A Sensor Manual Recovery
Pressure A Sensor Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Pressure Sensors: Pressure A Sensor Shutdown
Pressure B Sensor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Pressure Sensors: Pressure B Sensor Alert
Pressure B Sensor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Pressure Sensors: Pressure B Sensor Alert Enable
Pressure Cutoff Close
TB > Configure/Setup > Detailed Setup > Response Control > Travel / Pressure Control > Pressure Control: Pressure Cutoff Close
Pressure Cutoff Open
TB > Configure/Setup > Detailed Setup > Response Control > Travel / Pressure Control > Pressure Control: Pressure Cutoff Open
Pressure Integral Deadzone
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning: Pressure Integral Deadzone
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning: Pressure Integral Gain
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning: Pressure Integral Limit Hi
Pressure Integral Limit Lo
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning: Pressure Integral Limit Lo
Pressure MLFB Gain
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning: Pressure MLFB Gain
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning: Pressure Prop Gain
Pressure Range Hi
TB > Configure/Setup > Detailed Setup > Response Control > Travel / Pressure Control > Pressure Control: Pressure Range Hi
Pressure Range Lo
TB > Configure/Setup > Detailed Setup > Response Control > Travel / Pressure Control > Pressure Control: Pressure Range Lo
Pressure Tuning Set
TB > Configure/Setup > Detailed Setup > Response Control > Pressure Tuning: Pressure Tuning Set
-Continued-
305
Instruction Manual

August 2012
D103412X012

Parameter Label
Pressure A
Path to Parameter
TB > Device Variables > Overview > Pressures: Pressure A
TB > Device Diagnostics > Status > Self Test Status: Pressure A Sensor Failure
Pressure B
TB > Device Variables > Overview > Pressures: Pressure B
TB > Device Diagnostics > Status > Self Test Status: Pressure B Sensor Failure
Pressure Differential
TB > Device Variables > Overview > Pressures: Pressure Diff
Pressure Fallback Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Pressure Fallback: Pressure Fallback Alert
Pressure Fallback Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Pressure Fallback: Pressure Fallback Alert Enable
Pressure Units
TB > Configure/Setup > Detailed Setup > Instrument > Units: Pressure Units
Processor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: Processor Alert
Processor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: Processor Alert Enable
Program Memory Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: Program Memory Alert Enable
Program Memory Manual Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: Program Memory Manual Recovery
Program Memory Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: Program Memory Shutdown
Program Memory Alert
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: Program Memory Alert
Protection
TB > Device Variables > Overview > Protection
Proximity Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Proximity: Proximity Hi Alert
Proximity Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Proximity: Proximity Hi Alert Enable
Proximity Hi Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Proximity: Proximity Hi Hi Alert
Proximity Hi Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Proximity: Proximity Hi Hi Alert Enable
Proximity Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Proximity: Proximity Lo Alert
Proximity Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Proximity: Proximity Lo Alert Enable
Proximity Lo Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Proximity: Proximity Lo Lo Alert
Proximity Lo Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Proximity: Proximity Lo Lo Alert Enable
Push Down To
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Push Down To
Simulate PlantWeb Alerts
TB > Configure/Setup > Detailed Setup > Alert Handling > Simulate PlantWeb Alerts
Rated Travel
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Rated Travel
Relay Type
TB > Configure/Setup > Detailed Setup > Instrument > Application: Relay Type
Seat Type
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Seat Type
Setpoint
TB > Device Variables > Overview > AO ControlPreCharacterization: Setpoint
Setpoint Status
TB > Device Variables > Overview > AO ControlPreCharacterization: Setpoint Status
Setpoint(D)
TB > Device Variables > Overview > DO Control: Setpoint(D)
Shaft Stem Diameter
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Shaft Stem Dia
Simulate Active
TB > Device Diagnostics > Status > Transducer Block Error: Simulate Active
Simulate Jumper ON
TB > Device Diagnostics > Status > Self Test Status: Simulate Jumper ON
Spring Rate
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Spring Rate
Spring Rate Units
TB > Configure/Setup > Detailed Setup > Instrument > Units: Spring Rate Units
Static Memory Alert
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: Static Memory Alert
Static Memory Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: Static Memory Alert Enable
Static Memory Manual Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: Static Memory Manual Recovery
Static Memory Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Electronic > Processor Impaired: Static Memory Shutdown
Stroke Time Close
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Reference > Stroke Time Close
Stroke Time Open
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Reference > Stroke Time Open
Supply Pressure Maximum
TB > Device Diagnostics > Device Record > Supp Pressure Max
Supply Pressure Maximum Time
TB > Device Diagnostics > Device Record > Supp Pressure Maximum Time
Supp Pressure Minimum
TB > Device Diagnostics > Device Record > Supp Pressure Minimum
Supp Pressure Minimum Time
TB > Device Diagnostics > Device Record > Supp Pressure Minimum Time
Supply Pressure
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Supply Pressure: Supply Pressure
Supply Pressure
TB > Device Variables > Overview > Pressures: Supply Pressure
Supply Pressure Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Supply Pressure: Supply Pressure Hi Alert
Supply Pressure Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Supply Pressure: Pressure Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Supply Pressure: Supply Pressure Hi Alert Point
Supply Pressure Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Supply Pressure: Supply Pressure Lo Alert
Supply Pressure Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Supply Pressure: Supply Pressure Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Supply Pressure: Supply Pressure Lo Alert Point
-Continued-
306
Instruction Manual
D103412X012
August 2012

Parameter Label
Path to Parameter
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Pressure Sensors: Supply Pressure Sensor Alert
Supply Pressure Sensor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Pressure Sensors: Supply Pressure Sensor Alert Enable
TB > Device Diagnostics > Status > Self Test Status: Supply Sensor Failure
Tag Description
TB > Configure/Setup > Detailed Setup > Instrument > Tag Description
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Temperature Limit: Temperature Hi Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Temperature Limit: Temperature Lo Alert Point
Temperature Maximum
TB > Device Diagnostics > Device Record > Temperature Maximum
Temperature Maximum Time
TB > Device Diagnostics > Device Record > Temperature Maximum Time
Temperature Minimum
TB > Device Diagnostics > Device Record > Temperature Minimum
Temperature Minimum Time
TB > Device Diagnostics > Device Record > Temperature Minimum Time
Temperature
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Temperature Limit: Temperature
TB > Device Variables > Overview > Temperature
Temperature Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Temperature Limit: Temperature Hi Alert
Temperature Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Temperature Limit: Temperature Hi Alert Enable
Temperature Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Temperature Limit: Temperature Lo Alert
Temperature Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Temperature Limit: Temperature Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Environment > Temperature Limit: Temperature Lo Alert Point
Temperature Sensor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Temperature Sensor: Temperature Sensor Alert
Temperature Sensor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Temperature Sensor: Temperature Sensor Alert Enable
Temperature Units
TB > Configure/Setup > Detailed Setup > Instrument > Units: Temperature Units
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Travel
Travel
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel
TB > Device Variables > Overview > AO Control PostCharacterization: Travel
Travel(D)
TB > Device Variables > Overview > DO Control: Travel(D)
Travel(DeChar)
TB > Device Variables > Overview > AO Control PreCharacterization: Travel(DeChar)
Travel Status
TB > Device Variables > Overview > AO Control PostCharacterization: Travel Status
Trend
TB > Device Diagnostics > Trend
Trim Style 1
Trim Style 2
Travel Accumulator
TB > Configure/Setup > Detailed Setup > Alerts > Travel History > Travel Accumulator: Travel Accumulator
TB > Device Variables > Overview > Travel Accumulator
Travel Accumulator Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel History > Travel Accumulator: Travel Accumulator Alert
Travel Accumulator Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel History > Travel Accumulator: Travel Accumulator Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel History > Travel Accumulator: Travel Accumulator Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Travel History > Travel Accumulator: Travel Accumulator Deadband
Travel Closed Alert
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Travel Closed: Travel Closed Alert
Travel Closed Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Travel Closed: Travel Closed Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Travel Closed: Travel Closed Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Travel Closed: Travel Closed Deadband
Travel Count
TB > Device Variables > Overview > Travel Count
Travel Cutoff Hi
TB > Configure/Setup > Detailed Setup > Response Control > Travel / Pressure Control > Travel Control: Travel Cutoff Hi
Travel Cutoff Lo
TB > Configure/Setup > Detailed Setup > Response Control > Travel / Pressure Control > Travel Control: Travel Cutoff Lo
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Deviation: Travel Deviation Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Travel: Travel Deviation Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel: Travel Deviation Time
Travel Deviation Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Deviation: Travel Deviation Alert
Travel Deviation Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Deviation: Travel Deviation Alert Enable
Travel Integral Deadzone
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning: Travel Integral Deadzone
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning: Travel Integral Enable
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning: Travel Integral Limit Hi
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning: Travel Integral Limit Lo
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning: Travel Integral Gain
Travel Limit Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit Hi/Lo: Travel Limit Hi Alert
Travel Limit Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit Hi/Lo: Travel Limit Hi Alert Enable
-Continued-
307
Instruction Manual
August 2012
D103412X012

Parameter Label
Path to Parameter
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit Hi/Lo: Travel Hi Alert Point
Travel Hi Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit Hi/Lo: Travel Hi Deadband
Travel Limit Hi Hi Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit: Travel Limit Hi Hi Alert
Travel Limit Hi Hi Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit: Travel Limit Hi Hi Alert Enable
Travel Limit Hi Hi Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit: Travel Hi Hi Alert Point
Travel Limit Hi Hi Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit: Travel Hi Hi Deadband
Travel Limit Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit Hi/Lo: Travel Limit Lo Alert
Travel Limit Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit Hi/Lo: Travel Limit Lo Alert Enable
Travel Limit Lo Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit Hi/Lo: Travel Lo Alert Point
Travel Limit Lo Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit Hi/Lo: Travel Lo Deadband
Travel Limit Lo Lo Alert
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit: Travel Limit Lo Lo Alert
Travel Limit Lo Lo Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit: Travel Limit Lo Lo Alert Enable
Travel Limit Lo Lo Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit: Travel Lo Lo Alert Point
Travel Limit Lo Lo Deadband
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Limit: Travel Lo Lo Deadband
Travel MLFB Gain
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning: Travel MLFB Gain
Travel Open Alert
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Travel Open: Travel Open Alert
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Travel Open: Travel Open Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Travel Open: Travel Open Alert Point
TB > Configure/Setup > Detailed Setup > Alerts > Proximity > Travel Open: Travel Open Deadband
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning: Travel Proportional Gain
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Travel Sensor Motion
Travel Sensor Alert
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Travel Sensor: Travel Sensor Alert
Travel Sensor Alert Enable
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Travel Sensor: Travel Sensor Alert Enable
TB > Device Diagnostics > Status > Self Test Status: Travel Sensor Hi Error
TB > Device Diagnostics > Status > Self Test Status: Travel Sensor Lo Error
Travel Sensor Manual Recovery
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Travel Sensor: Travel Sensor Manual Recovery
Travel Sensor Shutdown
TB > Configure/Setup > Detailed Setup > Alerts > Sensor > Travel Sensor: Travel Sensor Shutdown
TB > Device Diagnostics > Status > Self Test Status: Travel Sensor Span Error
Travel Target
TB > Configure/Setup > Detailed Setup > Alerts > Travel > Travel Target
Travel Target
TB > Device Variables > Overview > AO Control PostCharacterization: Travel Target
Travel Tuning Set
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning: Travel Tuning Set
Travel Units
TB > Configure/Setup > Detailed Setup > Instrument > Units > Travel Units
TB > Configure/Setup > Detailed Setup > Response Control > Travel Tuning: Travel Velocity Gain
TB > Configure/Setup > Detailed Setup > Response Control > Travel / Pressure Control > Travel/Pressure Select
TB > Configure/Setup > Detailed Setup > Response Control > Travel / Pressure Control > Travel/Pressure State
TB > Device Variables > Overview > Travel/Pressure State
Unbalanced Area
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Trim > Unbalanced Area
Upper Bench Set
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Actuator > Upper Bench Set
Valve Class
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Class
Valve Manufacturer ID
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Manufacturer ID
Valve Model Number
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Model Number
Valve Serial Number
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Serial Number
Valve Size
308
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Size
TB > Configure/Setup > Detailed Setup > Valve and Actuator > Valve > Valve Style
TB > Configure/Setup > Detailed Setup > Instrument > Application: Zero Power Condition
Instruction Manual
D103412X012
August 2012
Table F2. Resource Block (RB) Parameters - Configuration Index

Parameter Name
Path to Parameter
Alert Key
RB > Configure/Setup > Setup > Alarm Handling > Alert Key
RB > Device Diagnostics > Status > Block Alarm: Alarm State
Block Alarm Disabled
RB > Configure/Setup > Setup > Alarm Handling > Block Alarm: Block Alarm Disabled
Block Alarm Auto Acknowledge
RB > Configure/Setup > Setup > Alarm Handling > Block Alarm: Block Alarm Auto Acknowledge
Discrete Alarm Auto Acknowledge
RB > Configure/Setup > Setup > Alarm Handling > Write Alarm: Discrete Alarm Auto Acknowledge
Confirm Time
RB > Configure/Setup > Setup > Alarm Handling > All Alarms: Confirm Time
Device ID
Device Revision
Device State
Device Type
DD Revision
Diagnostic Options
Electronics S/N
Factory S/N
Fault State
Features Available
RB > Configure/Setup > Setup > Identification > Identification: Device ID

RB > Device Variables > Instrument > Identification: Device ID
RB > Configure/Setup > Setup > Version > Version Information: Device Revision
RB > Device Variables > Instrument > Version Information: Device Revision
RB > Device Diagnostics > Status > Device State
RB > Configure/Setup > Setup > Identification > Identification: Device Type
RB > Device Variables > Identification: Device Type
RB > Configure/Setup > Setup > Version > Version Information: DD Revision
RB > Device Variables > Identification: DD Revision
RB > Configure/Setup > Setup > Options > Diagnostic Options
RB > Device Variables > Options > Diagnostics Options
RB > Configure/Setup > Setup > Identification > Identification:Electronics S/N
RB > Device Variables > Identification: Electronics S/N
RB > Configure/Setup > Setup > Identification > Identification:Factory S/N
RB > Device Variables > Identification: Factory S/N
RB > Device Diagnostics > Status > Fault State
RB > Configure/Setup > Setup > Options > Function Block Options
RB > Device Variables > Options > Function Block Options
RB > Configure/Setup > Setup > Options > Features Available
RB > Device Variables > Options > Features Available
Features Selected
RB > Configure/Setup > Setup > Options > Features Selected
Field S/N
RB > Configure/Setup > Setup > Identification > Identification: Field S/N
Field S/N
RB > Device Variables > Identification: Field S/N
Hardware Revision
RB > Configure/Setup > Setup > Version > Version Information: Hardware Revision
ITK Version
RB > Configure/Setup > Setup > Version > Version Information: ITK Version
Manufacturer
RB > Configure/Setup > Setup > Identification > Identification: Manufacturer
Manufacturer
RB > Device Variables > Identification: Manufacturer
Maximum Alerts Allow
RB > Configure/Setup > Setup > Alarm Handling > All Alarms: Maximum Alerts Allow
Maximum Alert Possible
RB > Configure/Setup > Setup > Alarm Handling > All Alarms: Maximum Alerts Possible
RB > Configure/Setup > Setup > Options > Miscellaneous Options

RB > Device Variables > Options > Miscellaneous Options
RB > Device Diagnostics > Status > Resource Block Error
RCas Timeout
RB > Configure/Setup > Setup > Comm Timeout > RCas Timeout
ROut Timeout
RB > Configure/Setup > Setup > Comm Timeout > ROut Timeout
Firmware Revision
RB > Configure/Setup > Setup > Version > Version Information: Firmware Revision
Status
RB > Device Diagnostics > Status
RB > Configure/Setup > Setup > Version > Version Information: Standby Firmware Revision
Strategy
Tag Description
RB > Configure/Setup > Setup > Identification > Identification: Strategy

RB > Device Variables > Identification: Strategy
RB > Configure/Setup > Setup > Identification > Identification: Tag Description
RB > Device Variables > Identification: Tag Description
RB > Device Diagnostics > Status > Write Alarm: Alarm State
Write Alarm Disabled
RB > Configure/Setup > Setup > Alarm Handling > Write Alarm: Write Alarm Disabled
Write Lock
Write Priority
RB > Configure/Setup > Setup > Write Lock > Write Lock
RB > Device Diagnostics > Status > Write Lock
RB > Configure/Setup > Setup > Write Lock > Write Priority
309

August 2012
Instruction Manual
D103412X012
Introduction
Note
This appendix does not necessarily provide the latest information on the DeltaV system. For the latest information on using the
DeltaV system, refer to the online help or documentation supplied with the system.
This appendix provides specific instructions for performing basic setup operations on the DeltaV host system. It is not
a comprehensive resource, rather a starting point. For more information, refer to the following sources:
Section 3: Basic Setup and Tuning for detailed information regarding initial setup, and stabilizing and optimizing valve
response.
Section 4: Detailed Setup for detailed information on configuring all of the blocks in the instrument, and an overview
of the function blocks.
Section 5: Calibration for complete calibration information.
Appendix A: Principle of Operation for information on how digital valve controller operation.
Appendix D: FOUNDATION fieldbus Communication for an overview of function block and block modes, as well as
additional information pertaining to fieldbus communication.
Appendix E: DD Installation for information on installing the device description (DD) software on your host system.
DeltaV OnLine Help or Documentation for complete and current information about navigating in the DeltaV system.
Software Functionality/System Requirements

DVC6200f digital valve controllers are designed to permit remote setup, calibration, and testing using Process
Systems DeltaV system as the host system.
To use the methods, accessed as described in this appendix, requires that the device description (DD) for the
DVC6200f digital valve controller be installed on the host system. For information on installing the device description,
refer to DD Installation (Appendix E) and the host system documentation.
Using AMS Device Manager

Refer to figures F1 and F2 to access the digital valve controller using AMS Suite: Intelligent Device Manager.
1. Start DeltaV Explorer by selecting DeltaV Explorer from the Start menu.
2. Locate the the digital valve controller icon in the All Containers pane (the left panel) and rightclick once on the
digital valve controller icon or name.
3. Locate Open with AMS Device Manager in the context menu and leftclick to bring up the Device Connection View.
4. Navigate to the digital valve controller icon or name as shown in figure F2 and leftclick.
310
Instruction Manual
D103412X012
August 2012
Figure F1. Navigating to AMS Device Manager
DIGITAL VALVE
CONTROLLER ICON
AND NAME
OPEN WITH AMS

DEVICE MANAGER
Figure F2. Accessing the Digital Valve Controller Through AMS Device Manager
LEFTCLICK TO
ACCESS THE DELTAV
NETWORK
DIGITAL VALVE
CONTROLLER
ICON AND
NAME
311

August 2012
Instruction Manual
D103412X012
Methods
Transducer Block
The following methods are accessed via the transducer block: Device Setup, Auto Travel Calibration, Manual Travel
Calibration, Supply Sensor Calibration, Output A Sensor Calibration, Output B Sensor Calibration, Travel Sensor Adjust,
Stroke Valve, Performance Tuner, Stabilize/Optimize, and Relay Adjust.
Refer to figures F1, F2, and F3 and the following steps to access these methods.
2. Locate the the digital valve controller icon in the All Containers pane (the left panel) and rightclick once on the
digital valve controller icon or name.
5. Locate Methods in the Actions menu, as shown in figure F3 and rightclick once.
6. Select the desired method from the the Actions menu and leftclick to start the method.
Resource Block
The Restart Options method and the DD Information method are available via the resource block. Refer to figure F3
and the following steps to access these methods.
2. Locate the digital valve controller icon in the All Containers pane (the left panel) and rightclick once on the digital
valve controller icon or name.
5. Locate Methods in the Actions menu, as shown in figure F3 and rightclick once.
6. Select the desired method from the the Actions menu and leftclick to start the method.
Accessing Parameters
Transducer Block
For detailed information on the parameters that are changed via the transducer block, refer to the Detailed Setup
section of this manual. Refer to figures F2, F3, and F4 for information on accessing transducer block parameters.
2. Locate the digital valve controller icon in the All Containers pane and rightclick once on the digital valve controller
icon or name.
5. Locate Configure/Setup in the Actions menu (see figure F3) and leftclick to access Configuration and Setup
parameters.
6. Leftclick on Digital Valve Controller (TRANSDUCER) to access the transducer block parameters. Refer to table F1
for the transducer block configuration menu.
312
Instruction Manual
D103412X012
Figure F3. Actions Menu
August 2012
ACTIONS
CONFIGURE/SETUP
RESOURCE BLOCK
METHODS
TRANSDUCER
BLOCK METHODS
Note
To access diagnostic parameters leftclick on Device Diagnostics, and then on Digital Valve Controller (TRANSDUCER). See
figure F4.
To access device variables leftclick on Device Variables, and then on Digital Valve Controller (TRANSDUCER). See figure F4.
313
Instruction Manual
August 2012
D103412X012
Figure F4. Accessing Configure/Setup, Device Diagnostics, and Device Variables
DIGITAL VALVE
CONTROLLER
(TRANSDUCER)
RESOURCE
(RESOURCE)
DEVICE
DIAGNOSTICS
DEVICE
VARIABLES
Resource Block
For detailed information on the parameters that are changed via the resource block, refer to the Detailed Setup
section of this manual. Refer to figures F2, F3, and F4 for information on accessing resource block parameters.
2. Locate the digital valve controller icon in the All Containers pane and rightclick once on the block icon or name.
5. Locate Configure/Setup in the Actions menu (see figure F3) and leftclick to access Configuration and Setup
parameters.
6. Leftclick on Resource (RESOURCE) to access the resource block parameters. Refer to table F2 for the resource
block configuration menu.
Note
To access diagnostic parameters leftclick on Device Diagnostics, and then on Resource (RESOURCE). See figure F4.
To access device variables leftclick on Device Variables, and then on Resource (RESOURCE). See figure F4.
314
Instruction Manual
D103412X012
August 2012
Bringing the Device OnLine

To completely configure the digital valve controller for use in a fieldbus loop, the following conditions must be met.
Refer to DeltaV OnLineHelp or documentation for detailed information on accomplishing these steps.
1. A place holder must be created - a place holder is an electronic representation of the digital valve controller that
exists in the DeltaV database with no associated physical device.
2. Device must be commissioned - Commissioning the device involves downloading applicable parameters from the
device place holder to the physical device.
3. Any additional configuration that is required, such as setting alarms, cutoffs, and other resource block and
transducer block parameters. See the Detailed Setup section of this manual.
4. Define the control strategy
5. Associate I/O to the digital valve controller.
6. The device is now ready to be downloaded.
PlantWeb Alerts
Fieldbus devices detect and report their device alarms to a DeltaV system (or other host system). This includes
detecting whether an alert condition is active, reporting the alarm to DeltaV and later clearing the alarm when the
condition is no longer active. Whether a particular alert condition can be suppressed, disabled or configured offline
are all determined by the device.
For Fieldbus, the DeltaV system is responsible for knowing which devices have alarms, ensuring that alarms are
properly represented (such as after controller switchovers) and reporting to operators, Event Chronicle, AMS, OPC
Alarms and Events server, etc. So the only alarms DeltaV shows for a Fieldbus device are those the device has defined
as alarms and has reported to DeltaV.
All device alarms are configured and processed in the DeltaV system identically to process alarms. This means that
how the alarms are communicated within the system, what workstations are notified, alarm annunciation, graphical
representations, event recording, acknowledgement, etc. are identical for process and device alarms. This ensures
that device alarms and process alarms are available to all users and applications in a consistent fashion.
Setting up PlantWeb Alerts

This section walks you through the steps and considerations to implement PlantWeb alerts.
DeltaV Hardware and Software Requirements

The first step to implement PlantWeb alerts is to have the correct hardware and software:
DeltaV v6.3 or later
DeltaV Operate
MD Controllers
Fieldbus devices - While device alerts are supported on all fieldbus devices, devices that offer PlantWeb alerts
provide significantly more useful information.
Series 2 H1 cards
315

August 2012
Instruction Manual
D103412X012
Initial Device Setup

When new FF devices are commissioned on the DeltaV system, device alarms are automatically enabled and default
priorities are assigned to the alarms. Select properties on the device, then the Alarms and Displays tab, as shown in
figure F5 to view whether device alarms are enabled on a particular device.
Figure F5. Alarms & Display Tab
The Enable Device Alarms configuration option modifies the device configuration. Thus changing this setting requires
a download to the device. Devices that are migrated from older DeltaV systems will have their device alarms disabled.
Note
1. Use the default setting of device alarms enabled. If the user does not want notification of device alarms, this can be configured
on each individual alarm. Later on, you can modify the alarm configurations without downloading the device. Disabling device
alarms disables all of the alarms, including the device communication failure alarm.
2. Use the same control display for the device as for the control module.
3. If you suspect a rogue device is generating extra H1 bus traffic from device alarms, disabling device alarms stops the device from
sending the alarms.
4. If the Alarms and Displays tab is not shown, then you either do not have an MD controller or the device is on a Series 1 H1 card.
316
Instruction Manual
D103412X012
August 2012
Area Assignment
Controllers use this area assignment to report node status (e.g. not communicating). Devices and control modules use
this area assignment to determine where to send their alarms.
Area A is the default area assignment for all controllers and workstations (see figures F6 and F7). Also, by default Area
A is assigned to all workstations Alarms and Events subsystem. This means that all controller status problems are sent
to all workstations by default.
Figure F6. Controller Properties
Figure F7. Device Properties
The controller is assigned to Area A. A device that is NOT yet

associated with a control module will default to the same area
as the controller.
A fieldbus device will change its area association once the device is configured to a control module. In addition, the
device is assigned to the same place in the logical hierarchy as this control module. So if the control module is under a
unit, the device is also considered under this same unit.
The device is automatically associated with the same area as the control module that uses the lowest index number
function block in the device. This block is usually the primary input or output function block of the device. This ensures
that wherever the control module is reporting information, all device information that may also be relevant is also
reported.
Note
1. For devices with multiple inputs or outputs (such as the 848), you need to decide which area is best for device alarm reporting
and be sure to assign the correct control module to the lowest index number function block. If there is no module assigned to this
function block, then the device will always be assigned to the same area as the controller.
2. With controller area default of AREA A, and the default of AREA A being assigned to all workstations, you need to evaluate the
alarm settings when commissioning a new fieldbus device with device alarms enabled. If the device detects a FAILED or COM FAIL
alarm prior to being assigned to a control module, this device alarm will be reported and annunciated to all workstations. This is
317

August 2012
Instruction Manual
D103412X012
because all workstations have Area A assigned. Consider lowering the priority of these alarms to ADVISORY until the end of the
commissioning process.
Reporting Alarms and Events to a Workstation

Device alarm and event reporting is no different than control module reporting. Alarm and event reporting to
workstations is determined by assigning areas to workstations. The workstation area assignment is all you need to do
to ensure that you have all of the information (device and process) for that area.
This is important so that ALL of the information about an area -- both the process and device information -- is available
at any workstation that is responsible for that area. That way the Event Chronicle has a complete record for that area,
and any user can drill into a graphic or tag and access all of the information.
This DOES NOT determine WHO views the device alarms. Who views the alarms is determined by filtering at each
workstation.
Now that all of the device (and process) information is assigned to a workstation, the next step is to decide what
priority of device and process alarms cause alarm annunciation to the users on that workstation.
Setting up WHO Sees Device Alarms

The priority of the alarms, and the settings at that workstation determine what alarms are annunciated on a particular
workstation. Annunciated means sound the horn and shown in the alarm banner, Alarm List display, etc.
There are two different approaches that can be used to adjust the device alarm filtering for a particular workstation:
Adjust the default DeltaV Operate alarm settings in the UserRef/UserSettings file
Adjust the individual device alarm priorities
By default, DeltaV Operator Stations have all process alarms are annunciated, and show up on the Alarm Banner, Alarm
List, graphical displays, etc. on all operator workstations. Also by default, the device alarms with priority settings below
WARNING (8) are NOT annunciated or shown in the alarm banner. The low priority device alarms can be shown in
graphics and on summaries defined to not be limited by the alarm settings.
The DeltaV Maintenance Station uses the same DeltaV Operate alarm setting for device alarm annunciation. This
license only shows device alarms on Maintenance Station graphics. NO process alarms are shown in the alarm banner
or ANY alarm summary.
Thus, device alarms and process alarms can be either combined and/or separated for specific user installations, based on
their operating philosophy.
Setting DeltaV Operate Device Alarm Annunciation Defaults

DeltaV Operate has default settings in the UserRef.grf file for what priority of device alarms will annunciate and show
in the alarm banner. The default DeltaV Operate alarm settings annunciate device alarms that are of the priority
WARNING (8) or higher. Device alarms below this priority will not sound the horn or show up in the alarm banner.
Operator Station displays can be configured to show any alarms reporting to that workstation. Along with typical
display configuration, alarm summaries can be configured to display alarms that match the alarm banner settings, or
user specified ranges. The standard AlarmSum display is configured to show all alarms reporting to that workstation
(see figure F8).
318
Instruction Manual
D103412X012

August 2012
Figure F8. DeltaV Alarm Summary Configuration
Each display alarm summary can be configured to

match the alarm banner or be uniquely defined.
Note
If you think you should be seeing a device alarm in the alarm banner and it is not there, verify that the device is shown on the
AlarmSum display. This display shows ALL of the alarms reporting to that workstation, regardless of the device alarm annunciation
settings. If the device is not shown in this display, then it is not reporting to this workstation (or the logged on user does not have
responsibility for that area).
The default for device alarm annunciation (sounds the horn and shown in the alarm banner) can be modified for all
operator/maintenance stations. Or unique settings can be defined for specific workstations. Use the workstation name
to adjust settings for specific workstations in UserSettings.grf.
For example, if an installation has a Maintenance Station named 'MAINT', then the UserRef.grf (then renamed to
UserSettings.grf) would contain alarm settings for the MAINT workstation as appropriate for maintenance (e.g. all
device alarms in the alarm banner).
Note
To easily find the device alarm configuration in UserRef or UserSettings, open the display in the Standard directory, right click and
select EDIT SCRIPT, then select Edit, Find and type in DEVICE. This will take you to the location in the file with the device alarm
settings.
319
Instruction Manual
August 2012
D103412X012
Deciding Device Alarm Priorities

Each device alarm, just like every process alarm, has a priority assigned to it. When a device is created, the device
alarms are assigned default alarm priorities as shown in figure F9.
Figure F9. Default PlantWeb Alert Priorities
The priority of a device alarm defines whether the

alarm is annunciated on a particular workstation, in
addition to the color of the alarm and the horn sound.
The DeltaV workstation default is to annunciate device alarms above the ADVISORY (7) priority.
Therefore, by default both the FAILED and COMM PlantWeb alerts annunciate to the operator.
The priority of each alarm needs to be considered. The priority of a device alarm is determined by how important that
device problem is and the consequences to the process.
The priority is not based solely on the type of device. This means that while some DVC6200f's may be critical to
operation, other DVC6200f's may not. In this example, the DVC6200f's would have different default alarm priorities.
Note
1. If your installation has the Fieldbus devices, but is not ready to use PlantWeb alerts, then you can disable the individual alarms at
the device - or through the System Alarm Management application. Later on, individual alarms can be enabled without having to
download the device.
2. When you first begin to use device alarms, be sure that your alarm priority settings for the workstations or the individual device
alarm priorities are such that they don't cause undue operator burden. This could mean only having a few device alarms set at
WARNING or above, or changing the DeltaV Operate default such that only CRITICAL device alarms (or even perhaps NO device
alarms annunciate to the operator).
3. DO NOT enable ALL of the PlantWeb alerts in a device. Only enable the alerts that are needed.
320
Instruction Manual
Glossary
D103412X012
August 2012
Glossary
Algorithm
A set of logical steps to solve a problem or
accomplish a task. A computer program contains
one or more algorithms.
Deadband
Region around a reference point that must be
exceeded before a new event occurs.
Deviation
Alphanumeric
Consisting of letters and numbers.
ANSI (acronym)
The acronym ANSI stands for the American
National Standards Institute
ANSI Class
Valve pressure/temperature rating.
Bench Set
Pressure, supplied to an actuator, required to
drive the actuator through rated valve travel.
Expressed in pounds per square inch.
Byte
A unit of binary digits (bits). A byte consists of
eight bits.
Configuration
Stored instructions and operating parameters for
a FIELDVUE Instrument.
Control Loop
An arrangement of physical and electronic
components for process control. The electronic
components of the loop continuously measure
one or more aspects of the process, then alter
those aspects as necessary to achieve a desired
process condition. A simple control loop
measures only one variable. More sophisticated
control loops measure many variables and
maintain specified relationships among those
variables.
Controller
Usually, the difference between set point and

process variable. More generally, any departure
from a desired or expected value or pattern.
Device ID
Unique identifier embedded in the instrument at
the factory.
Drive Signal
The signal to the I/P converter from the printed
wiring board. It is the percentage of the total
microprocessor effort needed to drive the valve
fully open. In most applications, drive signal
ranges from 55% to 75%.
Feedback Arm
The mechanical connection between the valve
stem linkage and the FIELDVUE Instrument travel
sensor.
Feedback Signal
Indicates to the instrument the actual position of
the valve. The travel sensor provides the feedback
signal to the instrument printed wiring board
assembly. A mechanical linkage connects the
travel sensor to the valve stem or shaft.
Firmware
The combination of a hardware device and
computer instructions and data that reside as
readonly software on that device.
Note
1. This term (firmware) is sometimes used to refer only to
the hardware device or only to the computer instructions or
data, but these meanings are deprecated.
2. The confusion surrounding this term has led some to
suggest that it be avoided altogether. The term is included
here because of its use in older documentation and culture.
A device that operates automatically to regulate a

controlled variable.
321
Instruction Manual
Glossary
August 2012
Gain
The ratio of output change to input change.
D103412X012
Pressure Sensor
A FIELDVUE instrument internal device that
senses the output pressure from the pneumatic
relay.
Hardware Revision
Revision number of the Fisher instrument
hardware. The physical components of the
instrument are defined as the hardware.
Instrument Level
Determines the functions available for the
instrument.
Random Access Memory (RAM)

A type of semiconductor memory that is normally
used by the microprocessor during normal
operation that permits rapid retrieval and storage
of programs and data. See also Read Only
Memory (ROM) and NonVolatile Memory (NVM).
Rate
Leak Class
Defines the allowable leakage by a valve when it is
closed. Leak class numbers are listed in two
standards: ANSI/FCI 702 and IEC 5344.
Linearity, dynamic
Linearity (independent) is the maximum
deviation from a straight line best fit to the
opening and closing curves and a line
representing the average value of those curves.
Memory
A type of semiconductor used for storing
programs or data. FIELDVUE instruments use
three types of memory: Random Access Memory
(RAM), Read Only Memory (ROM), and
NonVolatile Memory (NVM).
NonVolatile Memory (NVM)

A type of semiconductor memory that retains its
contents even though power is disconnected.
NVM contents can be changed during
configuration unlike ROM which can be changed
only at time of instrument manufacture. NVM
stores configuration restart data.
Amount of change in output proportional to the

rate of change in input.
ReadOnly Memory (ROM)

A memory in which information is stored at the
time of instrument manufacture. You can
examine but not change ROM contents.
Seat Load
Force exerted on the valve seat, typically
expressed in pounds force per lineal inch of port
circumference. Seat load is determined by shutoff
requirements.
Software
Computer programs, procedures, and possibly
associated documentation and data pertaining to
the operation of a computer system.
Temperature Sensor
A device within the FIELDVUE instrument that
measures the instrument's internal temperature.
Travel
Movement of the valve stem or shaft which
changes the amount the valve is open or closed.
Octet
See byte
Parallel
Simultaneous: said of data transmission on two or
more channels at the same time.
322
Travel Sensor
A device within the FIELDVUE instrument that
senses valve stem or shaft movement. The travel
sensor in the DVC6200f is the Hall Effect sensor
that measures the position of the magnet
assembly.
Instruction Manual
Glossary
D103412X012

Increasing or decreasing air pressure causes the
magnet assembly to move up or down or the
rotary shaft to turn clockwise or
counterclockwise. Device Setup asks if it can
move the valve to determine travel.
Tuning
The adjustment of control terms or parameter
values to produce a desired control effect.
Tuning Set
Preset values that identify gain and rate settings
for a FIELDVUE instrument. The tuning set and
supply pressure together determine an
instrument's response to input signal changes.
August 2012
Watch Dog Timer

A timer that the microprocessor must pulse
periodically. If the microprocessor is unable to
pulse the timer, the instrument shuts down.

The position of the valve (open or closed) when
the electrical segment power to the instrument is
removed. Zero Power Condition (ZPC) is
determined by relay and actuator action where:
for Relay A and C, Port A will be at atmosphere
pressure, and if doubleacting, Port B will be at
supply pressure. For Relay B, Port B will be at
supply pressure.
323
Glossary
August 2012
324
Instruction Manual
D103412X012
Instruction Manual
Index
D103412X012
Index
A
Acknowledge Option, Resource Block, 48
Act On IR, 131
Action on Failure, DI Function Block, 205
Action on Fault Detection
AO Function Block, 118
DO Function Block, 194
Active PlantWeb Alerts, 224
Actuator
Fail Action, 83
Manufacturer, 83
Model Number, 83
Serial Number, 83
Size, 83
Style, 83
Device Setup, 42
Actuator Compatibility, 8
Actuator Information, for initial setup, 41
Advanced Diagnostics (AD), 4
Air, 84
as supply medium, 7, 27
Alarm Detection
AI Function Block, 171
DI Function Block, 205
ISEL Function Block, 151
PID Function Block, 131
Alarm Handling, 47
Alarm Priorities
Alert Conditions, 224
Instrument, 69
August 2012
Alerts
Configuration, 71
Electronics, 69
Environment, 73
Instrument, 69
Performance, 79
PlantWeb, 69
Proximity, 76
Sensor, 72
Travel, 74
AMS Device Manager, using, 310
Analog Input (AI) Function Block, 5, 171
Advanced Features, 175
Alarm Detection, 171
Block Errors, 175
Field Communicator Menu Structure, 182
Filtering, 174
Modes, 171
parameters, 176
Signal Conversion, 174
Simulation, 175
Status Handling, 173
Troubleshooting, 176
View Lists, 180
Analog Output (AO) Function Block, 5, 113
Action on Fault Detection, 118
Application Information, 119
Block Errors, 119
I/O Options, 118
Mode Handling, 115
parameters, 120
Set Point Selection and Limiting, 117
Setting the Output, 116
Simulation, 119
View Lists, 124
ANSI/ISA75.13.01 Section 5.3.5, Vibration Testing
Method, 8
AO Control - PreCharacterization, Device Variables,
230
AO ControlPost Characterization, Device Variables,
230
Alert Handling, 86
PlantWeb Alert Handling, 86
PlantWeb Alert Simulate, 86
PlantWeb Alerts, 275
Simulate Active Alerts, 86
MAI Function Block, 184
Alert Key, 72
Area Units, 81
Alert Reporting, PlantWeb Alerts, 277
ATEX, 8
325
Instruction Manual
Index
August 2012
Auto Calibration, 214
D103412X012
Supply Pressure Sensor, 216

Calibration Date, 81
B
Backup Link Master, 7
Basic Setup, 39
Bench Set
Lower, 84
Upper, 84
Block Alarm, Resource Block, 221
Block Alarm Auto Acknowledge, Resource Block, 48
Block Alarm Disabled, Resource Block, 48
Block Error
Resource Block, 220
Transducer Block, 227
Block Error Reporting, 86
Block Errors, 86
Resource Block, 49
Block Execution Times, 7
Calibration Location, 81
Calibration Person, 81
Certification
INMETRO, Brazil, 8
KGS, Korea, 8
NEPSI, China, 8
TIIS, Japan, 8
Clear Fault State, Resource Block, 222
Commissioning Tag, 37
Communication Connections, 36
Communication Time Out, 46
Shed Remote Cascade, 46
Shed Remote Out, 46
Configuration Alerts, 71, 224
Alert Key, 72
Blocks Set to Default, 72, 225
Output Block Timeout, 71, 224
Configure/Setup, 45
Confirm Time, 48
Connections
Communications, 36
Pneumatic, 26
Pressure, 26
Supply, 27
Specifications, 8
Vent, 30
Wiring and Electrical, 31
Fieldbus, 31
Block Modes, 289

All, Device Variables, 229
DVC6200f, 289
Construction Materials, 9
Blocks
Function, 5
Resource Block, 5
Transducer Block, 5
CSA, 8
Blocks Set to Default, Alerts, 72
C
Calibration, 213
Auto, 214
Manual, 214
Pressure A or B Sensor, 217
Relay, 215
326
control options, PID Function Block, 130

Control selections, 4
Custom Characterization, 68
Cycle Counter
Alerts, 78
Device Variables, 231
D
DD Information, 223
Declaration of SEP, 9
DeltaV ProfessionalPLUS Workstation, Installing DD
on, 298
Instruction Manual
Index
D103412X012
DeltaV System
operating with, 303
Software Functionality/System Requirements, 310
DeltaV Tune, for PID control loops, 132
Detailed Setup, 62
Device Addressing, 293
Device Communication, 294
Scheduled Transfers, 294
Unscheduled Transfers, 295
Device Description, Overview, 297
Device Description Version, displaying, 301
Device Descriptions, 291
Installing on a DeltaV ProfessionalPLUS Workstation,
298
Installing on Other Fieldbus Host Systems, 300
Device Diagnostics
Resource Block, 220
Device ID, 37, 48, 222
Device Revision, 49, 223
Device Setup, 40
Device State, Resource Block, 220
Device Type, 48, 223
Device Variables
Resource Block, 222
diagnostic capabilities, 4
Diagnostic Options, 46, 49, 223
August 2012
Modes, 202
parameters, 206
Simulation, 205
View Lists, 210
Discrete Output (DO) Function Block, 5, 189
Action on Fault Detection, 194
Block Errors, 194
Block Initialization, 192
I/O Selection, 192
Mode Handling, 191
Modes, 190
Output Block PV Status, 193
parameters, 195
Setting the Output, 192
Shed Options RCAS Mode Only, 191
Simulation, 194
View Lists, 199
DO Control, Device Variables, 230
DoubleActing Relay, calibration, 215
Drive Current, Alerts, 69
Drive Signal
Alerts, 70
DVC6205 base unit, 14
E
Educational Services, 10
Effective Area, 84
Direct Action, PID Function Block, 131
Electrical Classification
Electrical Housing, 8
Hazardous Area Approvals, 8
Direct Selection of Inputs, ISEL Function Block, 151
Electrical Housing, 8
Direct signal conversion, AI Function Block, 174
Electromagnetic Compatibility, Specification, 8
Disabling Inputs, ISEL Function Block, 150
Electronics Alerts, 69, 224

Drive Current, 69, 224
Drive Signal, 70, 224
Processor Impaired, 70, 224
Digital Communication Protocol, 7
Discrete Alarm Auto Acknowledge, 48

Discrete Alarm Disabled, 48
Discrete Input (DI) Function Block, 5, 201
Action on Failure, 205
Block Errors, 205
Block Initialization, 202
Field Value Processing, 204
I/O Selection, 202
Electronics Serial Number, 48, 222

EMC Summary ResultsImmunity, 9
EN 61326-1 (First Edition), 8
Enable Jumper, Simulate, 36
Environment Alerts, 73, 225
Supply Pressure, 73, 225
Temperature Limit, 74, 225
327
Instruction Manual
Index
August 2012
Expert tuning, 43
Pressure, 66
Travel, 63
F
Factory Serial Number, 48, 222
D103412X012
Function Blocks, 5
Analog Input (AI), 5, 171
Analog Output (AO), 5, 113
Discrete Input (DI), 201
Discrete Output (DO), 5, 189
Input Selector (ISEL), 5
Multiple Analog Input (MAI), 5, 183
Output Splitter (OS), 5, 160
Proportional-Integral-Derivative (PID), 5, 126
Fail Action, Actuator, 83

Fault State, Resource Block, 222
Features Available, 47
Features Selected, 47
Feedback Connection Options, 83
G
Gain Values, preselected tuning sets, 43
Gas Certified, DVC6200f, 8, 27
Gauges, Pipe Plugs, or Tire Valves, maintenance, 241
Feedforward Calculation, PID Function Block, 130

OS Function Block, 170
H
Hardware Revision, 49, 223
Field Serial Number, 48, 222
Hazardous Area Approvals, 8

ATEX, 8
CSA, 8
FM, 8
IECEx, 8
Field Value Processing, DI Function Block, 204
Humidity Testing, Method, 8
Fieldbus Connections, 31
Quick Connect Cable Entry, 33
Twisted Shielded Pair, 32
Fieldbus Control (FC), 4
I/O Options, AO Function Block, 118
Fieldbus Diagnostics (FD), 4
I/O Selection
Fieldbus Installation and Wiring Guidelines, 10

Fieldbus Logic (FL), 4
Fieldbus Wiring, connecting, 31
Filtering
I/P Converter
maintenance, 237
removing, 238
replacing, 238
I/P Filter, replacing, 237
Firmware Revision, 49, 223
Identification of Selected Inputs, ISEL Function Block,

151
Flow Direction, 82
IEC 61514-2, humidity testing method, 8
FM, 8
IECEx, 8
Function Block
Input Selector (ISEL), 145
Overview, 287
Independent Linearity, Specification, 8
Function Block Options, 46, 223

Function Block Scheduling, 296
328
Indirect signal conversion, AI Function Block, 174

Indirect Square Root, AI Function Block, 174
Initialization and Back Calculation Requirements, OS
Function Block, 165
Instruction Manual
Index
D103412X012
August 2012
INMETRO, Brazil, Certification, 8
Link Active Scheduler (LAS), 293
Input Characterization, 67
linkageless, noncontacting position measurement,

12
Input Selection, ISEL Function Block, 150
Lower Bench Set, 84
Input Selector (ISEL) Function Block, 5, 145

Alarm Priorities, 152
Block Errors, 152
Input Selection, 150
Direct Selection of Inputs, 151
Disabling Inputs, 150
Identification of Selected Inputs, 151
Modes, 145
parameters, 152
Limit Propagation, 147
Quality Use and Propagation, 146
STATUS_OPTS Supported, 150
Substatus Propagation, 147
View Lists, 157
Input to Output Mapping, OS Function Block, 163
Installation, 11
Instrument Alert, Conditions, 275
Instrument Alert Conditions, 69, 224
ITK Version, 49, 223
K
KGS, Korea, Certification, 8
M
magnet assemblies, 13
linear, 12
magnet assembly
material, 12
travel range, 12
Magnetic Feedback Assembly, replacing, 234
Magnetic Tools, use of, 12, 17
Magnets, high power, 12, 17
MAI Channel Map, 85
MAI Function Block, parameters, 185
Maintenance
Gauges, Pipe Plugs, or Tire Valves, 241
I/P Converter, 237
Module Base, 234, 235
Pneumatic Relay, 240
PWB Assembly, 239
Resource Block, 221
Terminal Box, 241
Tools Required, 234
Fieldbus Connections with Twisted Shielded Pair, 32
Manual Calibration, 214
Manufacturer Identification, 48, 223
Maximum Notify, 48
L
Last Calibration Type, 81
Leak Class, 82
Length Units, 81
Lever Arm Length, 84
Lever Style, 84
Lightning and Surge Protection, 8
Limit Handling, OS Function Block, 163
Limit Notify, 48
Limit Propagation
Maximum Output Capacity, Specification, 7

Maximum Recorded Supply Pressure, 228
Maximum Recorded Supply Pressure Time, 228
Maximum Recorded Temperature, 228
Maximum Recorded Temperature Time, 228
Maximum Supply Pressure, 81
Methods, 298
Minimum Recorded Supply Pressure, 228
Minimum Recorded Supply Pressure Time, 228
Minimum Recorded Temperature, 228
Minimum Recorded Temperature Time, 228
Miscellaneous Options, 47, 223
329
Instruction Manual
Index
August 2012
Mode Handling
Modes
Blocks, 289
Explanation of, 290
Resource Block, 45
Module Base
removing, 235
replacing, 236
D103412X012
O
Open/Closed Limit Switch, Channel 24 and 25, DI
Function Block, 203
Options, 9
Resource Block
Diagnostic, 46
Features Selected, 47
Function Block, 46
Miscellaneous, 47
Outblock Selection, 69
Output Block PV Status, 85
Output Block Timeout, Alerts, 71
Output Connection, 28
Output Selection and Limiting, PID Function Block, 130
Output Signal, Specifications, 7
Mounting
67CFR, 26
DVC6200f, 11
DVC6205 base unit
Pipestand, 14
Wall, 14
DVC6215 feedback unit, 16
Troubleshooting, 243
Output Splitter (OS) Function Block, 5, 160

Initialization and Back Calculation Requirements,
165
Modes, 161
parameters, 167
View Lists, 169
mounting brackets, for DVC6200f, 13
Output Tracking, PID Function Block, 130
mounting instructions, 13, 14

mounting kits, DVC6200f, 13
Multiple Analog Input (MAI) Function Block, 5, 183
Modes, 183
View Lists, 187
P
Parameters
Resource Block, 54
natural gas, as supply medium, 7, 8, 27, 233
Parts Kits, 249
NEPSI, China, Certification, 8
Parts List, 250
Network Communication, 293
Parts Ordering, 249
Network Management, 296

Nominal Supply Pressure, 84
330
PD Inside Status
Alert, 79
Instruction Manual
Index
D103412X012
PD Run, Alert, 80
Performance Alerts, 79, 226
PD Inside Status, 79
PD Run, 80
Performance Critical, 80, 226
Performance Information, 80
Performance Reduced, 80
Performance Critical, Alerts, 80
August 2012
Performance, 79
Proximity, 76
Sensor, 72
Set Block Status, 277
Setting, 277
Travel, 74
Travel History, 78
Using, 277, 281
PlantWeb Alerts Set PV Status, 86
Performance Diagnostics (PD), 4
Pneumatic Connections, 26
Performance Information, Alerts, 80
Pneumatic Relay
removing, 240
replacing, 240
Performance Reduced, Alerts, 80

Performance Tuner, 43, 44, 64
PID Equation Structures for Enhanced PID Block, 131
Alarm Priorities, 132
Block Errors, 132
Feedforward Calculation, 130
Filtering, 130
Mode Handling, 128
Modes, 128
Output Selection and Limiting, 130
Output Tracking, 130
parameters, 133
Reverse and Direct Action, 131
Set Point Tracking, 130
PlantWeb Alert Enable, 80
Advise Enable, 80
Failed Enable, 80
Maintenance Enable, 80
PlantWeb Alert Handling, Alert Handling, 86
PlantWeb Alert Reporting, 80
Advise Suppress, 81
Failed Suppress, 80
Maintenance Suppress, 80
Port Diameter, 82
Port Type, 82
Pressure, Connections, 26
Pressure A or B Sensor, calibration, 217
Pressure Cutoff Closed, 67
Pressure Cutoff Open, 67
Pressure Fallback, Alerts, 73
Pressure Fallback Auto Recovery, 66
Pressure Fallback Manual Recovery, 66
Pressure Integral Dead Zone, 66
Pressure Integral Gain, 66
Pressure Integral Limit Hi, 66
Pressure Integral Limit Lo, 66
Pressure MLFB Gain, 66
Pressure Proportional Gain, 66
Pressure Range Hi, 67
Pressure Range Lo, 67
Pressure Sensors, Alerts, 72
Pressure Tuning, 65
Pressure Tuning Set, 65
PlantWeb Alert Simulate, Alert Handling, 86
Pressure Tuning Sets, Gain Values, 66
PlantWeb Alerts, 69
Alert Handling, 275
Alert Reporting, 277
Conditions, 275
Configuration, 71
Electronics, 69
Environment, 73
in a DeltaV System, 315
Mode-Based, 275
Pressure Units, 81
Pressures, 232
Principle of Operation, Block Diagram, 259
Printed Wiring Board (PWB) Assembly
removing, 239
replacing, 239
Processor Impaired, Alerts, 70
331
Instruction Manual
Index
August 2012
ProportionalIntegralDerivative (PID) Function Block,

5
Protection, 39, 62
Proximity, Alerts, 77
Proximity Alerts, 76, 225
Proximity, 77, 226
Travel, 76
Travel Closed, 77, 226
Travel Open, 77, 225
Push Down To, 82
D103412X012
Set Fault State, 222

Strategy, 222
Tag Description, 222
View Lists, 61
Device Diagnostics, 220
Write Lock, 220
Resource Block (RB)
Menu Structure, 272
Menu Tree, 273
Resource Block Error, 220
Resource Block Mode, 45
Response Control, 63
Restart Actions, Resource Block, 221
Quality Use and Propagation, ISEL Function Block, 146
Restart Processor, Resource Block, 222
Quick Connect Cable Entry, 33
Restart with Defaults

parameters affected by, 50
Resource Block, 222
R
Regulator (67CFR), 26
Casing-Mounted, 26
Integral-Mounted, 26
Yoke-Mounted, 26
Related Documents, 10
Relay, calibration, 215
Relay A, 215
Relay B, 40, 215, 216
Relay C, 215, 216
Relay Type, 81
Remote Travel Sensor Connections, 34
remote vent, 30
Resource Block, 288
Block Alarm, 221
Block Errors, 49
Clear Fault State, 222
Device State, 220
Options
Diagnostic, 223
Function Block, 223
Miscellaneous, 223
Overview, 45
parameters, 54
Restart Actions, 221
332
Reverse Action, PID Function Block, 131
S
Scheduled Transfers, Device Communication, 294
Seat Type, 82
Self Test Status, 226
Sensor Alerts, 72, 225
Pressure Fallback, 73, 225
Pressure Sensors, 72, 225
Temperature Sensor, 225
Travel Sensor, 225
Travel Sensor Alert, 72
Serial Number
Actuator, 83
Electronics, 48, 222
Factory, 48, 222
Field, 48, 222
Valve, 82
Set Block Status, PlantWeb Alerts, 277
Set Fault State, Resource Block, 222
Set Point Selection and Limiting, AO Function Block,
117
Set Point Tracking, PID Function Block, 130
Instruction Manual
Index
D103412X012
August 2012
Setting the Output

Output Block PV Status, AO Function Block, 117
Steady-State Air Consumption, Specifications, 7
Shed Options RCAS Mode Only, DO Function Block,

191
Stroking Time Close, 84

Substatus Propagation, ISEL Function Block, 147
Signal Conversion, AI Function Block, 174

Simulate Active Alerts, Alert Handling, 86
SIMULATE ENABLE terminals, 36
Simulation
SingleActing Relays, calibration, 216
Solenoid Valve Testing, Special Construction to
Support Testing, 29
SP Track retained Target, 130
SP-PV Track in LO or IMan, 130
SP-PV Track in Man, 130
SP-PV Track in ROUT, 130
Special Instructions for Safe Use and Installations in
Hazardous Locations, 11
Strategy, Resource Block, 48, 222

Stroking the Digital Valve Controller Output, 242
Stroking Time Open, 84
Supply, Connections, 27
Output, 28
Supply Pressure
Alerts, 73
Maximum, 81
Maximum Recorded, 228
Minimum Recorded, 228
Specifications, 7
Supply Pressure Sensor, calibration, 216
T
Tag Description
Resource Block, 48, 222
Temperature
Maximum Recorded, 228
Minimum Recorded, 228
Temperature Limit, Alerts, 74
Specifications, DVC6200f, 7
Temperature Limits, Operating Ambient, 8
Spring Rate, 84
Temperature Units, 81
Spring Rate Units, 81

Stabilize/Optimize, 43, 64
Terminal Box
removing, 241
replacing, 242
Standard Control (SC), 4
TIIS, Japan, Certification, 8
Standby Firmware Revision, 49, 223

Block Error, 227
Device Diagnostics, 224
parameters, 87
Status and Limit Propagation, 291
View Lists, 110
static discharge, avoiding, 233

Status Handling
Transducer Block (TB)

Menu Structure, 262
Menu Tree, 267, 268, 269, 270, 271
Transducer Block Mode, 39, 62
Status Propagation, Transducer Block, 292
Transducer Block Overview, 62
STATUS_OPTS Supported, ISEL Function Block, 150
Travel, Alert, 74, 76
333
Instruction Manual
Index
August 2012
D103412X012
Travel Accumulator
Alerts, 78
Travel/Pressure State, 66
Travel Alerts, 74, 225

Travel, 74
Travel Deviation, 74, 225
Travel Hi/Lo, 76, 225
Travel Limit, 75, 225
Travel Target, 74
Trim Style 1, 84
Travel Closed, Alerts, 77

Travel Count, Device Variables, 231
Travel Cutoff Hi, 67
Travel Cutoff Lo, 67
Travel Deviation, Alerts, 74
Travel Deviation Pressure Fallback, 67
Travel Hi/Lo, Alerts, 76
Travel History, Alerts, 78
Travel History Alerts, 78, 226
Cycle Counter, 78, 226
Travel Accumulator, 78, 226
Travel Integral Dead Zone, 64
Travel Integral Enable, 64
Travel Integral Gain, 64
Travel Integral Limit Hi, 64
Travel Integral Limit Lo, 64
Trend, 229
Trim Style 2, 84
Troubleshooting
DVC6200f, 243
mounting, 243
utility connections, 243
Tuning
Pressure, 65
Travel, 63
Tuning Set
Device Setup, 43
Pressure, 65
Travel, 63
Tuning Set B, 43
Tuning Sets, Gain Values, 43
U
Unbalanced Area, 82
Unscheduled Transfers, Device Communication, 295
Upper Bench Set, 84
Utility Connections, Troubleshooting, 243
Travel Limit, Alerts, 75

Travel MLFB Gain, 64
Travel Open, Alerts, 77
Travel Pressure Control, 66
Travel Proportional Gain, 64
Travel Sensor, Alerts, 72
Travel Sensor Motion, 83, 84
Device Setup, 42
Travel Target, Alert, 74
Travel Tuning, 63
Travel Tuning Set, 63
Travel Tuning Sets, Gain Values, 63
Travel Units, 81
V
Valve
Actual Travel, 82
Class, 82
Inlet Pressure, 82
Manufacturer, 82
Model Number, 82
Outlet Pressure, 82
Packing Type, 82
Serial Number, 82
Shaft Stem Diameter, 82
Size, 82
Style, 82
Device Setup, 42
Travel Velocity Gain, 64
Valve Position Proximity Detection, Channels 30-33, DI

Function Block, 203
Travel/Pressure Select, 66
Valve Travel, Channel 23, DI Function Block, 202
334
Instruction Manual
Index
D103412X012
Variable Limit Switch, Channels 26-29, DI Function

Block, 203
Vent, 30
Vibration Testing, Method, 8
August 2012
W
Weight
DVC6200f, 8
DVC6205f, 8
DVC6215, 8
View / Edit Feedback Connection, 83
Wiring and Electrical Connections, 31
View Lists, 219

Analog Output (AO) Function Block, 124
Resource Block, 61
Write Alarm, 48
Write Lock, 45
Resource Block, 220
Write Lock, 45
Write Priority, 46
Z
Zero Power Condition, 81
Device Setup, 42
335
Index
August 2012
336
Instruction Manual
D103412X012
N97
Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance
of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user.
Fisher, FIELDVUE, ValveLink, PlantWeb, DeltaV, and Baumann are marks owned by one of the companies in the Emerson Process Management business unit
of Emerson Electric Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co.
FOUNDATION fieldbus is a mark owned by the Fieldbus Foundation. All other marks are the property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not
to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are
governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such
products at any time without notice.
Emerson Process Management
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Chatham, Kent ME4 4QZ UK
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
2010, 2012 Fisher Controls International LLC. All rights reserved.

DVC6200f Instruction Manual

Uploaded by

Copyright:

Available Formats

DVC6200f Instruction Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DVC6200f Instruction Manual

Uploaded by

Copyright:

Available Formats

Instruction Manual

DVC6200f Digital Valve Controller

Fisherr FIELDVUE DVC6200f Digital Valve

This manual applies to:

DVC6200f Digital Valve Controller

Figure 11. FIELDVUE DVC6200f Digital Valve

Section 3 Basic Setup . . . . . . . . . . . . . . . . . 39

Input Selector Function Block . . . . . . . . . . . . . . . . .

Section 5 Calibration . . . . . . . . . . . . . . . . 213

Section 6 Viewing Device

Section 4 Detailed Setup . . . . . . . . . . . . . . 45

Replacing the Magnetic Feedback Assembly . . . . . 234

Section 7 Maintenance and

DVC6200f Digital Valve Controller

Section 8 Parts . . . . . . . . . . . . . . . . . . . . . 249

Appendix A Principle of Operation . . . . . 259

Appendix B Field Communicator

Appendix D FOUNDATION Fieldbus

Instrument Specific Blocks . . . . . . . . . . . . . . . . . .

Appendix E Device Description

Appendix F Operating with a

Introduction and Specifications

Section 1 Introduction and Specifications

Introduction and Specifications

Figure 12 FIELDVUE DVC6200f Digital Valve

Figure 13. FIELDVUE DVC6200f Digital Valve

Introduction and Specifications

Introduction and Specifications

Using This Manual

RB > Configure/Setup > Setup > Resource Block Mode

Introduction and Specifications

Table 11. Specifications

Fieldbus Device Capabilities

Introduction and Specifications

Table 11. Specifications (continued)

Humidity Testing Method

Stem Travel (SlidingStem Linear)

Introduction and Specifications

Table 11. Specifications (continued)

Table 12. EMC Summary ResultsImmunity

Electrostatic discharge (ESD)

80 to 1000 MHz @ 10V/m with 1 kHz AM at 80%

Rated power frequency

150 kHz to 80 MHz at 3 Vrms

Performance criteria: +/- 1% effect.

Introduction and Specifications

Use of Magnetic Tools with the DVC6200f

Figure 22. Travel Range

VALID TRAVEL RANGE

Table 21. FIELDVUE DVC6200f Mounting Instructions

585C/585CR Size 25 Actuator with or without Handjack

585C/585CR Size 50 Actuator with or without Handjack

657 and 667 Size 30-60 Actuators

657 and 667 Size 34-60 Actuators with Handwheel

657 and 667 Size 80 Actuators (up to 2 inch travel)

657 and 667 Size 80 Actuators (4 inch travel)

1051 Size 33 and 1052 Size 20 and 33 Actuators (Window Mount)

1051 and 1052 Size 33 Actuators (End Mount)

1051 and 1052 Size 40-70 Actuators (Window Mount)

1051 and 1052 Size 40-70 Actuators (End Mount)