Servo?

Dghvukhiojopk,o robotics. The motors are small, as you can see by the picture above, have built in control
circuitry, and are extremely pogchjbjkhoifgiyclubjk nstandard servo such as the Futaba S-148 has 42 oz/inches
of torque, which is pretty strong for its size. It also draws power proportional to the mechanical load. A lightly
loaded servo, therefore, doesn't consume much energy. The guts of a servo motor are shown in the picture
below. You can see the control circuitry, the motor, a set of gears, and the case. You can also see the 3 wires that
connect to the outside world. One is for power (+5volts), ground, and the white wire is the control wire.

(Click on picture for larger view)

somewhere around 180 degrees. Usually, its somewhere in the 210 degree range, but it varies by manufacturer.
A normal servo is used to control an angular motion of between 0 and 180 degrees. A normal servo is
mechanically not capable of turning any farther due to a mechanical stop built on to the main output gear.
The amount of power applied to the motor is proportional to the distance it needs to travel. So, if the shaft needs
to turn a large distance, the motor will run at full speed. If it needs to turn only a small amount, the motor will
run at a slower speed. This is called proportional control.
How do you communicate the angle at which the servo should turn? The control wire is used to communicate
the angle. The angle is determined by the duration of a pulse that is applied to the control wire. This is called
Pulse Coded Modulation. The servo expects to see a pulse every 20 milliseconds (.02 seconds). The length of
the pulse will determine how far the motor turns. A 1.5 millisecond pulse, for example, will make the motor turn
to the 90 degree position (often called the neutral position). If the pulse is shorter than 1.5 ms, then the motor
will turn the shaft to closer to 0 degress. If the pulse is longer than 1.5ms, the shaft turns closer to 180 degress.

As you can see in the picture, the duration of the pulse dictates the angle of the output shaft (shown as the green
circle with the arrow). Note that the times here are illustrative, and the actual timings depend on the motor
manufacturer. The principle, however, is the same.
ACTUATORS - SERVOS
Wiring
Control
Current, Torque
Gears
Velocity
Efficiency, Noise
Voltage Regulation
Digital vs Analog Servos
Hitec vs Futaba
Click to learn how to modify a servo for continuous rotation.
Click to learn how to waterproof a servo for continuous rotation.
What is a Servo?
Servos are DC motors with built in gearing and feedback control loop circuitry. And no motor drivers
required!
Synopsis
Servos are extremely popular with robot, RC plane, and RC boat builders. Most servo motors can rotate
about 90 to 180 degrees. Some rotate through a full 360 degrees or more. However, servos are unable to
continually rotate, meaning they can't be used for driving wheels (unless modified), but their precision
positioning makes them ideal for robot arms and legs, rack and pinion steering, and sensor scanners to
name a few. Since servos are fully self contained, the velocity and angle control loops are very easy to
impliment, while prices remain very affordable. To use a servo, simply connect the black wire to ground,
the red to a 4.8-6V source, and the yellow/white wire to a signal generator (such as from your
microcontroller). Vary the square wave pulse width from 1-2ms and your servo is now position/velocity
controlled.

Learn how to mount wheels onto servos.

Learn how to mount servos onto a robot chassis.
Servo Wiring
All servos have three wires:
Black or Brown is for ground.
Red is for power (~4.8-6V).
Yellow, Orange, or White is the signal wire (3-5V).
Servo Voltage (Red and Black/Brown wires)
Servos can operate under a range of voltages. Typical operation is from 4.8V to 6V. There are a few
micro sized servos that can operate at less, and now a few Hitec servos that operate at much more. The
reason for this standard range is because most microcontrollers and RC receivers operate near this
voltage. So what voltage should you operate at? Well, unless you have a battery voltage/current/power
limitation, you should operate at 6V. This is simply because DC motors have higher torque at higher
voltages.
Signal Wire (Yellow/Orange/White wire)
While the black and red wires provide power to the motor, the signal wire is what you use to command
the servo. The general concept is to simply send an ordinary logic square wave to your servo at a
specific wave length, and your servo goes to a particular angle (or velocity if your servo is modified).
The wavelength directly maps to servo angle.
So how do you apply this square wave to your servo? If your robot is remote controlled, your RC
receiver will apply the proper square wave for you. If however your robot is running from a
microcontroller, you must:
bring high a digital port
wait between 1-2ms
bring low the same digital port
cycle a few dozen times per second
Note, if you are running multiple servos simultaneously, you can just put a few of these program blocks
in sequential order. You can run as many servos as you have of digital ports.
So how many milliseconds do you keep the port high? It all depends on the servo. You may have to
tweak for each individual servo some several microseconds difference.

The standard time vs. angle is represented in this chart:

Servo Current
Servo current operates the same as in a DC motor, except that you now also have a hard to predict
feedback control system to contend with. If your DC motor is not at the specified angle, it will suddenly
draw huge amounts of current to reach that angle. But there are other peculiarities as well. If you run an
experiment with a servo at a fixed angle and hang precision weights from the servo horn, the measured
current will not be what you expect. One would think that the current would increase at some fixed rate
as the weights increased linearly. Instead you will get unpredictable curves and multiple rates.
In conclusion, servo current draw is very unpredictable.
Stall Torque, Stall Current, Current Drain
Since servos contain DC motors, please read my DC motor tutorial to learn about servo stall
characteristics.

Gear Types
More expensive servos come with metal gears for higher torque and longer life, followed by karbonite
and then nylon gears for the cheapest.
Nylon Gears - Nylon gears are most common in servos. They are extremely smooth with little or no
wear factors. They are also very lightweight, but lack in durability and strength.
Karbonite Gears - Karbonite gears are relatively new to the market. They offer almost 5 times the
strength of nylon gears and also better wear resistance. Cycle times of well over 300,000 have been
observed with these gears with virtually no wear. Servos with these gears are more expensive but what
you get in durability is more than equaled.
Metal Gears - Metal gears have been around for sometime now. Although the heaviest and having the
highest wear rate of all gear types, they offer unparalleled strength. With a metal output shaft, side-loads
can be much greater. Ever had a nylon output shaft crack? I have. In applications that are jarred around,

metal gears are best. Unfortunately, due to wear, metal gears will eventually develop slight play in the
gear-train. Accuracy will slowly be lost.
Velocity
The servo turn rate, or transit time, is used for determining servo rotational velocity. This is the amount
of time it takes for the servo to move a set amount, usually 60 degrees. For example, suppose you have a
servo with a transit time of 0.17sec/60 degrees at no load. This means it would take nearly half a second
to rotate an entire 180 degrees. More if the servo were under a load. This information is very important
if high servo response speed is a requirement of your robot application. It is also useful for determining
the maximum forward velocity of your robot if your servo is modified for full rotation. Remember, the
worst case turning time is when the servo is at the minimum rotation angle and is then commanded to go
to maximum rotation angle, all while under load. This can take several seconds on a very high torque
servo.

Efficiency and Noise

Due to noise and control circuitry requirements, servos are less efficient than DC motors uncontrolled.
To begin with, the control circuitry typically drains 5-8mA just on idle. Secondly, noise can more than
triple current draw during a holding position (not moving), and almost double current during rotation.
Noise is often a major source of servo inefficiency and therefore should be avoided. Ever notice your
servo jitter or vibrate? This is because your servo is rapidly jumping between two different angles due
to interference. What causes this interference? Well the signal wire is no different than a long antennae,
capable of accepting unwanted foreign signals and sending them straight to your servo as a command. A
common interference source is usually from other nearby servos and/or servo wiring. How to prevent
this problem? Keep your signal wire short, meaning do not add say 3+ feet of extension cables to your
servo. If you have many servo wires going through one area, and it isn't feasible to keep them apart, then
twist them together. Supposedly this reduces cross interference and I've heard it works, although I
cannot really tell for sure myself. You can also buy something called a servo booster extension which
buffers and amplifies the signal.

Regulating Voltage to a Servo

As you should already know, servos have a voltage rating. Go above that voltage and your servo
overheats and possibly fries. So suppose you have a 7.2V battery and you want to use a 5V regulator to
power your servos, is that a good idea?
Short answer: No!
Longer answer . . . it will work, but its a huge waste of battery power.
So lets say you have your 7.2V regulated to 5V and the servos draw a total of 1.5A of current.

Wasted power is:

(7.2V-5V)*1.5A = 3.3W
Percentage wise, its
(7.2V-5V)/7.2V = 30.6%
Thats the battery energy percentage wasted to thermal heat - almost 1/3rd!!!
Speaking of heat, your voltage regulator probably has thermal shutdown, meaning that if it overheats it
will throttle down current to your servos - meaning your servos will have lower torque and lower speed.
If your voltage regulator doesn't have thermal shutdown, it will just fry instead (not a good thing).
But if you still really really need to regulate for servos, get a switching regulator (like ~83% efficiency
on average).

Digital Servos vs Analog Servos

What is the difference between an analog and digital servo?
Digital servos, at the user end, are controlled no differently than analog servos. The difference is in how
the servo motor is controlled via the circuit board (amplifier). The motor of an analog servo receives a
signal from the amplifier 30 times a second or at 30Hz. This signal allows the amplifier to update the
motor position. Digital servos use a high frequency amplifier that updates the servo motor position 300
times a second or at 300Hz. By updating the motor position more often, the digital servo can deliver full
torque from the beginning of movement and increases the holding power of the servo. The quick refresh
also allows the digital servo to have a tighter deadband.
With the exception of a higher cost, there are only advantages for digital servos over analog servos.
The digital micro processor is 10 times faster than an analog servo. This results in a much quicker
response from the beginning with the servo developing all the rated torque 1 degree off of the center
point. Be aware that this faster response also results in higher starting currents, so make sure your
batteries can handle it.
Digital servos can be programmed for direction of rotation, center and end points, failsafe option,
speed, and dead bandwidth adjustment. This is great for matching sets of servos for deadband width,
center and end points in giant scale aircraft applications, and for reversing a digital servo when two are
used on a "Y" harness (below image).

If you do not want to deal with the added complication of programming, no worries! Hitec digital servos
will perform like standard servos out of the box. It is not required to program them before use.
The standing torque of a digital servo is 3 times that of its analog counterpart. This means digital servos
are typically smaller and have more torque.
What about servo modification? Digital servos are also modifiable, just check the datasheet to make
sure.
Hitec vs Futaba
There are actually four major servo manufacturers - Hitec, Futaba, Airtronics, and JR Radios. The last
two are uncommon today, so I wont talk about them. Hitec and Futaba servos work the same, but there
are several interfacing differences which you should be aware of.

The first is wire color, as Hitec uses a yellow signal wire while Futaba uses a white one. The wiring
order is the same, just different colors.
The second is connector compatibility. Futaba (J type) has a special flange thingy while Hitec (S type,
for universal) does not. Futaba has the extra flange to help the user plug in the servo correctly, although
there are only two ways to do it and connecting a servo in the wrong way will not actually damage
anything. If you want to connect a Futaba servo to a Hitec device, just clip the flange off and use
sandpaper to file it down until it fits. If you ever need to connect a Hitec connector to something Futaba,
just use sandpaper to decrease the connector width until it fits.

The third is price. All things kept the same, Hitec servos are cheaper than Futaba servos. But don't let
this be your only determining factor in your decision, as Futaba has some servo sizes that Hitec does
not.
The last major difference is in the spline. The spline is the output shaft of the servo. This is where you
would attach your servo horn or servo arm. Standard Hitec splines have 24 teeth while standard Futaba
splines have 25 teeth. What makes this important is that servo horns built for one will not work with the
other.