Prowirl 73F DN 100
Prowirl 73F DN 100
Prowirl 73F DN 100
Project :
Customer:
Contact person:
C.Project No.:
Fax:
Phone:
eMail:
TAG : --Timestamp:
Sales order number:
---
Review number:
---
Methane (Gas)
Gas
Clean
Not abrasive
Dangerous Fluid (Fluid group 1)
Newtonian
Ref. Temperature
Ref. Pressure
Atmospheric Pressure
Standard
0 C
1.013 bar_a
1.0132 bar_a
EN/DIN/ISO
Sizing Sheet
General Parameters
Fluid
State
Character
Abrasivity
Fluid Group (PED)
Fluid Type
Operating Conditions
Requested Flow
minimum
nominal
maximum
250
500
Nm3/h
Pressure
80
Temperature
40
mbar_g
C
Density
0.6747
kg/m3
Viscosity
0.01167
cP
Z-factor
0.9985
Pressure (min/max)
80
80
mbar_g
Temp. (min/max)
40
40
Vortex (Prowirl)
DN 100
213.203 Nm3/h
213.203 Nm3/h
3 002.08 Nm3/h
SS 1.4408 / CF3M
PN 16 EN 1092-1 B1, 1.4404/316L Flange
Application is Cat. II
Item
Flowmeter
Description
Prowirl 73F
*The user is responsible for the selection of process-wetted materials in view of their corrosion resistance. Endress+Hauser makes no guarantees and
assumes no liability for the corrosion resistance of the materials selected here for the application described above.
** The PED category is an Endress+Hauser recommendation and depends on the fluid category, process data as well from the max. permissible
pressure of the selected pressure rating.The fluids of the Applicator data base are classified to 67/548/EWG.
-1/3-
Under no circumstances is Endress+Hauser liable for errors, neither in the Software and in its documentation, nor for any errors
and consequential damage which may arise out of their use. The results in Applicator apply to parameters entered by the user. A
change in these parameters could lead to different results. Mandatory data are in the according technical information (TI).
C.Project No.:
Fax:
Phone:
eMail:
TAG : --Timestamp:
Sales order number:
---
Review number:
---
Sizing Sheet
Sizing and Calculated Results
minimum
nominal
maximum
Requested Flow
250
500
Velocity
9.993
19.99
m/s
Pressure loss
0.45
1.81
mbar
n.a.
n.a.
n.a.
n.a.
Reynolds No.
56 026
112 052
Frequency
94.1
188.2
Nm3/h
Hz
***For error calculation, the specified reference conditions for the calibration of the flowmeter according to ISO/IEC 17025 apply. Further information in
technical documentation.
Warnings / Messages
1. Requested min. flow too small for flowmeter range. Please adapt the min. flow or select a smaller size (if available) or select another flowmeter.
-2/3-
Under no circumstances is Endress+Hauser liable for errors, neither in the Software and in its documentation, nor for any errors
and consequential damage which may arise out of their use. The results in Applicator apply to parameters entered by the user. A
change in these parameters could lead to different results. Mandatory data are in the according technical information (TI).
C.Project No.:
Fax:
Phone:
eMail:
TAG : --Timestamp:
Sales order number:
---
Review number:
---
Methane (Gas)
State
Gas
Chemical formula
CH4
Calculation standard
NEL
Medium character
Clean
Gas mixture
Component
Fluid Type
Newtonian
1 Methane (Gas)
100 Mole%
100 Mass%
Fluid stability
Stable
0 Mole%
0 Mass%
0 Mole%
0 Mass%
0 Mole%
0 Mass%
0 Mole%
0 Mass%
0 Mole%
0 Mass%
0 Mole%
0 Mass%
0 Mole%
0 Mass%
Fluid description
Fraction
-82.61 C
Tm (Melting point)
-182.5 C
Pc (Critical pressure)
45 950 mbar
Tb (Boiling point)
-161.6 C
162 kg/m3
Calculated results
Density nom.
0.6747 kg/m3
Pressure nom.
80 mbar_g
Molar mass
16.043 kg/kmol
Temperature nom.
40 C
Z-factor nom.
0.9985
Viscosity nom.
0.01167 cP
458.1 m/s
2.276 kJ/(kg*K)
0.037 W/(m K)
0%
1.0132 bar_a
1.0132 bar_a
Density normal
0.7174 kg/m3
Density standard
0.6798 kg/m3
Temperature
0 C
Temperature
59 F
Pressure
1.0132 bar_a
Pressure
14.696 psi_a
-3/3-
Under no circumstances is Endress+Hauser liable for errors, neither in the Software and in its documentation, nor for any errors
and consequential damage which may arise out of their use. The results in Applicator apply to parameters entered by the user. A
change in these parameters could lead to different results. Mandatory data are in the according technical information (TI).