Struct Multidisc Optim (2013) 48:267277

DOI 10.1007/s00158-013-0910-0

RESEARCH PAPER

Maxwells reciprocal diagrams and discrete Michell frames

William F. Baker Lauren L. Beghini
Arkadiusz Mazurek Juan Carrion
Alessandro Beghini

Received: 26 November 2012 / Revised: 5 February 2013 / Accepted: 6 February 2013 / Published online: 16 March 2013
The Author(s) 2013. This article is published with open access at Springerlink.com

Abstract This paper unites two major legacies of James

Clerk Maxwells ground-breaking paper, On Reciprocal
Figures, Frames, and Diagrams of Forces (Maxwell, Philos Mag 26:250-261, 1864; Edinb Roy Soc Proc 7:160208,
1870): (i) the fundamental theorem used by Michell (Philos Mag 8(47):589597, 1904) to derive trusses of least
weight and (ii) reciprocal frames. This paper presents some
remarkable relationships between discrete Michell frames
and their corresponding reciprocal force polygons using
Graphic Statics. Several examples are given to illustrate the
notions of duality and self-reciprocity in these diagrams,
with particular emphasis placed on discrete optimal benchmark structures. For a given connectivity of nodes, Graphic
Statics provides all of the information needed to determine the total load path of the structure in the form and
force diagrams. Because the form and force diagrams are
reciprocal, in the course of finding one minimum load path
structure, a second minimum load path structure is also
found. These observations between the corresponding form
and force diagrams are generalized for discrete cantilever
Michell frames, and several comments on the extensions of
this work are included.

W. F. Baker () A. Mazurek J. Carrion A. Beghini

Skidmore, Owings & Merrill, LLP, 224 S. Michigan Avenue,
Chicago, IL 60604, USA
e-mail: william.baker@som.com
L. L. Beghini
Department of Civil and Environmental Engineering, University
of Illinois at Urbana-Champaign, 205 N. Matthews Ave., Urbana,
IL 61801, USA

Keywords Graphic Statics Reciprocal diagrams

Discrete optimal trusses Michell frames
James Clerk Maxwell

1 Introduction
Maxwell is the first word in A. G. M. Michells seminal
paper The Limits of Economy of Material in Framestructures (Michell 1904). Michell is referring to James
Clerk Maxwells paper On Reciprocal Figures, Frames,
and Diagrams of Forces (Maxwell 1870). The first equation in Michells paper (stating that the difference between
the total tension load paths and the total compression load
paths is equal to a constant is inferred from Maxwells
paper, which is also cited as the origin of reciprocal diagrams and Graphics Statics.
It should be noted that terminology has changed over the
150 years of work which form the basis of this paper. The
terms frames, structures, and trusses are used interchangeably within this paper and denote what are currently
known as trusses.
Maxwell starts with concepts from W. J. Macquorn
Rankines paper, Principle of the Equilibrium of Polyhedral Frames, (Rankine 1864) and extends the work to show
how certain trusses have reciprocal diagrams which represent the forces in the trusses. This approach had a major
impact on the field of structural engineering.
Maxwells work was interpreted and expanded by
many others including Jenkin (1869), Culmann (1864),
Cremona (1890), Wolfe (1921), and others as noted in Kurrer
(2008). It is of interest that Maxwell and Cremona considered two-dimensional form diagrams (trusses) and their
two-dimensional reciprocal force diagrams as the projection of three-dimensional polyhedra (one polyhedron for

268

members and one polyhedron for forces). Maxwell used a

paraboloid of revolution reciprocal mapping which resulted
in reciprocal lines that were perpendicular to each other in
projection, while Cremona used a hyperboloid reciprocal
mapping which resulted in reciprocal lines being parallel to
one another. The parallel mapping of reciprocal lines has
generally been used in practice.
Although Graphic Statics was a leading method of analyzing trusses in the late 19th and early 20th centuries, it is
not commonly employed in the 21st century. Historically,
graphical solutions for truss systems, cables and arches have
been used for a variety of design problems. Graphical calculation methods were a common method to calculate the
equilibrium of structures since the fundamental work by
Culmann (1864) for the engineers of the late 19th century
and early 20th century. Unfortunately, graphical methods
progressively lost popularity with the development of other
mathematical approaches. Examples of structures designed
using graphical methods include the work of the brilliant
structural designer Maillart (Zastavni 2008, 2010).
This paper will bring together these two threads of
Maxwells paper and show that some discrete Michell
trusses (frames) have a very remarkable relationship to the
reciprocal force polygons as determined by Graphic Statics.
The remainder of this paper is organized as follows: Section
2 provides a review of graphical methods and the notation used throughout this paper. Next, relationships between
paired optimal frames, with emphasis placed on their corresponding reciprocal diagrams, are described in Section
3. Section 4 introduces the notion of self-reciprocity in
Graphic Statics with several examples to illustrate the key
concepts. Generalized observations on discrete cantilever
Michell frames are provided in Section 5 followed by some
concluding remarks and extensions of this work.

2 Graphic statics
Graphical methods have been used for centuries to analyze
and design a variety of structures. In this section, we give
a brief historical review of such methods and introduce the
methodology and notation used throughout this work.
2.1 A history of graphical methods
The origin of Graphic Statics can be traced back to the writings of Simon Stevin (1586), in which a parallelogram rule
using force vectors and polygons was first used to analyze
forces in a structure. Later, Pierre Varignon (1687, 1725)
demonstrated the law of force polygon and introduced the
use of funicular polygons, but graphical (equilibrium) analysis using vectorized diagrams was not formalized until

W.F. Baker et al.

Culmann wrote his Die graphische Statik (Culmann 1864;

Block et al. 2006).
It was Maxwell, however, who first introduced the notion
of structural reciprocity to solve structural frames (Maxwell
1864, 1870). In these papers, Maxwell describes how one
could find forces in structural frames: a reciprocal diagram
can be generated by drawing lines perpendicular to the lines
of action of the structural members, such that all members
connected at a single node create a polygon. The resulting
diagrams were considered reciprocal, as Maxwell defined,
two figures are reciprocal when the properties of the first
relative to the second are the same as those of the second
relative to the first. The resulting lengths of the lines in
the new diagram are proportional to the forces in the original member diagram. This concept is described in more
detail in Section 3. Also, in this work, Professor Rankine
was acknowledged for being the first one to apply the most
general statement of graphical methods at the time.
Luigi Cremona (1890) further refined the method by
introducing a different node to polygon mapping technique,
in which the lines in the force diagram were parallel to
the lines of action of the structural members. These diagrams were easier to read than those of Maxwell, which
were rotated 90 . The Graphic Statics method introduced
by Cremona became so popular that nowadays, the graphical method of solving structural trusses is often called the
Cremona method.
Other contributors to the graphical methods include
Levy, who used them to calculate trusses and masonry
arch bridges in Levy (1888); Poleni; Lame and Clapeyron;
Poncelet; Rankine; Bow; Mohr, and Ritter. For more information, the interested reader can refer to the work of Wolfe
(1921), which explains how to solve various structural problems using Graphic Statics. The book by Zalewski and Allen
(1998) also presents step-by-step instructions for construction of the form and force diagrams, which we discuss
briefly in the next section. Furthermore, we note that similarly to the methodology presented next to find minimal
load path structures, Graphic Statics has also been applied
in Chapter 14 of the book by Zalewski and Allen (1998) for
form finding of trusses by graphically solving for the nodal
locations that give desired relative member forces.
More recently, Graphic Statics have been used in Block
et al. (2006) and Block and Ochsendorf (2007) for the
understanding of arch behavior, which is particularly useful
in compression shell design. In this work, a methodology
for generating compression-only vaulted surfaces and networks based on thrust line analysis and graphical methods
is discussed. A complete review of this methodology, Thrust
Network Analysis (TNA) and its applications, with emphasis on analysis of complex masonry vaults, can be found in
Block (2009).

Maxwells reciprocal diagrams and discrete Michell frames

269

Fig. 1 Graphic Statics

diagrams: a form diagram, b
force diagram

1
FAB

FBC

FCD

b
2,5

FEA

e
c

FDE

d
E

(a)

2.2 Methodology and notation of Graphic Statics

Graphic Statics is a graphical method of solving for the
forces in structural frames using two reciprocal diagrams,
and can be created using simple drafting tools. As noted in
the Maxwell quote above, each of the reciprocal diagrams
can be mapped into the other using the same procedure.
Each of the reciprocal diagrams in Graphic Statics consists
of a set of points, or nodes, straight lines interconnecting all
the nodes, and polygons defined by those lines. These polygons can be closed (i.e. defined by areas with closed loops
of finite lines) or open (i.e. defined by chains of finite lines
between two nodes with external loads).
The lines in the first diagram, called the form diagram,
represent structural members, or rather lines of action of the
structural members (see Fig. 1a). The lines in the second
diagram, known as the force diagram, represent forces carried by the members from the form diagram (see Fig. 1b).
In this figure, dashed line vectors are used to represent these
external forces both in the form and force diagrams. For
every line of action in the form diagram, there is a reciprocal line in the force diagram. That reciprocal line is drawn
parallel to the original line and its length is proportional to
the force in the original member. The reciprocity of the two
diagrams is as follows: Each polygon in the form diagram
maps to a node in the force diagram, each node in the form
diagram maps to a polygon in the force diagram and each

(b)

line in the form diagram maps to a parallel line in the force

diagram.
For simplicity, the notation used in the following diagrams is a version of Bows notation, also known as interval
notation (Bow 1873). For the form diagram, the capital letters, A, B, C,..., are sequentially placed clockwise in the
intervals between external forces (open polygons) and numbers, 1, 2, 3,..., are placed in the internal spaces (closed
polygons) between members. Each line in the form diagram
is bordered by two polygons. Thus, a member may be called
using the corresponding letter or number of the adjacent
polygons, e.g. A-1 or 2-3, and a joint called with a series of
letters and numbers, e.g. A-B-3-2-1-A. Similarly, the external forces are called using the adjacent open polygons, for
example FAB . The open polygons denoted by capital letters
in the form diagram correspond to points (nodes) on the load
line of the force diagram, denoted by the lowercase letters,
a, b, c,.... The numbers denoting the closed polygons in the
form diagram also have corresponding nodes in the force
diagram.
This graphical methodology allows the user to determine
the axial force in a truss member by measuring the length of
the reciprocal line in the force diagram. The relative scale of
the force diagram is set by drawing the load line representing the external forces to a scale. For example, the force in
member A-1 in Fig. 1a is proportional to the length of the
line between points a and 1 in Fig. 1b. Similarly, the force

Fig. 2 Example illustrating the

duality of optimal trusses: a
form diagram, b force diagram

A
1

2
a
1

FCA

FAB
C

FBC
(a)

c
(b)

270

W.F. Baker et al.

Fig. 3 Example illustrating the

duality of optimal trusses in Fig.
2: a form diagram, b force
diagram

FB

2
A

a
FA

1
C

FC

c
(a)

in the member between polygons 2 and 3 is proportional to

the length of the line between points 2 and 3 of the force
diagram. The remaining forces in the other members can be
computed likewise. Thus, the forces acting on a node in the
form diagram correspond to a polygon in the force diagram,
where each force is an edge of the polygon. For example, at
node A-B-3-2-1-A, the polygon of forces is given by points
a-b-3-2-1-a. Reading clockwise around joint A-B-3-2-1-A
in the form diagram, we can determine if members A-1 and
2-3 are in tension or compression. If read from 1 to a on
polygon a-b-3-2-1-a, we move from the left to the right,
towards the joint A-B-3-2-1-A of the form diagram. Thus,
member A-1 is in compression. Moving from 3 to 2 on the
force polygon goes from the upper left to the lower right, or
away from the joint in the form diagram, so member 3-2 is
in tension.

As shown in Stromberg et al. (2012), the minimal volume problem for a given set of balanced forces and nodal
connectivity can be written as follows:
x

1
|P | L

(1)

where x is a vector of design variables containing the nodal

coordinates of the unloaded nodes, is a constant that
Fig. 4 Example illustrating the
duality of optimal trusses: a
form diagram, b force diagram,
c dual truss

(a)

represents the allowable stress, L represents the lengths of

the members and P the internal forces of the members. We
note that if the structure is optimal,
the assumption of constant stress is valid. The quantity, |P | L, represents the
total load path of the structure; therefore, minimizing the
total load path of a structure corresponds directly to minimizing its volume, or weight. For a given connectivity of
nodes, Graphic Statics has all of the information needed to
determine this quantity: The form diagram gives the length,
L, of each member and the force diagram gives the force,
P , in each member.
A minimal load path structure can be found by changing the design variables, or in this case, the nodal locations
in the force diagram
 subject to the rules of reciprocal diagrams such that |P | L is minimized. In Graphic Statics,
the form diagram and the force diagram are, as Maxwell
noted, reciprocal. This leads to the remarkable observation
that the force diagram could also represent the geometry
of another optimal truss with its own external loads. In the
course of finding one minimum load path structure, a second minimum load path structure is also found. In addition,
the forces in the second minimum load path structure are
represented by the length of the lines in the original structure. These two trusses are both discrete optimal trusses for
their external loads in the sense that they are solutions to (1).
In Figs. 2 and 3, the structures (form diagrams) given on
the left are both different discrete optimal structures (Hemp
1973; Mazurek et al. 2011). The supposition that the force

3 Paired optimal trusses

min V = min

FAB

1
3

c
2

FC
1

b
FCA

C
(a)

FBC
(b)

FA

a
3

(c)

FB

Maxwells reciprocal diagrams and discrete Michell frames

Fig. 5 The solution to the
discrete Michell cantilever
(Chan 1960; Mazurek et al.
2011) is self-reciprocal: a form
diagram, b force diagram. The
geometries of the form and force
diagrams are the same

271

A
FCA

FBC

4
5
3
10 9
2
15
8
20 14
19 13
7
24 18
12
23
6
22 17
11
21 16

Fig. 6 The solution to this

three-point discrete frame is also
self-reciprocal: a form diagram,
b force diagram

FAB
b

FBC

4
3

15
20
14

7
13
19
6
12
18
11
24
17
16
23
21
22
(b)

forces and nodal connectivity (Prager 1970). The reciprocal

force diagram in the middle not only represents the forces of
truss but also the geometry of another optimal truss, where
the external forces for this optimal structure can also be
found by closing the open polygons in the form diagram.
For example, the external force applied at node a in Fig. 4b
is given by closing the open polygon, A, or drawing a line
from joint A-3-C-A to joint A-B-1-A. Figure 4c shows the
dual truss with the external loads given by closing all of the
polygons in (a).
The Appendix has a chart showing some dual discrete
trusses along with the Bow notation. This chart graphically
shows both the geometry and the forces for each pair of
optimal trusses.

4 Self-reciprocal discrete Michell frames

For some cases of paired trusses, it can be shown that
the geometry of the reciprocal force diagram is the exact
same as the member diagram; it can be said that these
types of structures are self-reciprocal. An example of a selfreciprocal structure is the optimal discrete Michell truss
taken from Chan (1960) and Mazurek et al. (2011) shown
in Fig. 5. This self-reciprocity can be observed for an
unbounded cantilever with an equal number of members at
each support when there is a single applied load acting parallel to a line drawn through the supports and the reactions
intersect the tip of the cantilever. Figure 6 shows another
example of a self-reciprocal frame for the three-point problem. We note here that the notion of self-reciprocity can
also apply for non-symmetric structures. The reasons for

FCA

10

B
(a)

diagram in Fig. 2 is also the geometry of a second discrete

optimal truss with its own loading is explored in Fig. 3. The
geometry of the truss in Fig. 3 (the form diagram) is taken
from the force diagram for Fig. 2.
Now that two optimal truss geometries have been found,
the remaining task is to find the external loads that correspond to a truss represented by the geometry of the force
diagram. The external forces for this second truss are found
by closing the open polygons of the original form diagram in a continuous manner. The vector formed by closing
an open polygon in the original form diagram is the external
force that would be applied to the node in the force diagram
that corresponds to the original open polygon. Closing the
open polygons provides the proper external forces for the
dual structure because it closes the force polygon at the node
which corresponds to the open polygon in the original form
diagram.
It is clear that the form and force reciprocal diagrams
in Figs. 2 and 3 are interchangeable. In order to make
the relationships more clear, Bows notation in Fig. 3 is
reversed.
For the problem in (1), the lengths are taken from the
truss on the left and the internal forces from the truss on
the right, though the reverse (i.e. internal forces from the
left diagram, lengths from the right diagram) would result in
the same optimal solution. The advantage to using Graphic
Statics for this class of optimal problems is that it provides
all of the information about the loads and the paths in a
graphical manner.
Another example of paired or dual discrete trusses is
given in Fig. 4, where the discrete truss on the left (form diagram) is the minimum load path structure for a given set of

1
2

FAB
B
(a)

c
3
(b)

272

W.F. Baker et al.

Fig. 7 Discrete optimal trusses

for the a 3-point problem and b
3-force problem with a 3 3
discretization

(a)

this remarkable self-reciprocity for certain discrete Michell

Frames is explained in Section 5.
Even though the form and force diagrams of selfreciprocal discrete Michell Frames are the same, the mapping between reciprocal lines is complex. For example, the
forces in the outside chords of the Michell cantilever in Fig.
5 are proportional to the lengths of the lines in the fans at
the supports. It is noteworthy that self-reciprocal Michell
Frames provide both the geometry and the forces in one diagram if one knows how to read the structure. As more and
more members are added to the discrete trusses, the solution
approaches the continuum solutions of Michell, Chan, and
others.

5 Generalized observations on discrete cantilever

Michell frames
Discrete optimal trusses for 3-point or 3-force problems
have been obtained in Mazurek et al. (2011) and Mazurek
(2012). The 3-point problem can be described by finding
the optimal (minimum load path) structure for two points
of support and a single point load. The 3-force problem is
when the optimal structure is found for three loaded points
(the three point loads must be in equilibrium). It has been
shown in Mazurek et al. (2011) and Mazurek (2012) that
Fig. 8 Duality in optimal
trusses for the generalized
3-force problem

(b)

the geometry of the optimal discrete trusses is fairly regular

regardless of the number of elements utilized in the solutions. The optimal truss geometry can also be defined using
only two parameters (i.e. angles and one of or )
for a 3-point problem (see Fig. 7a) or three parameters (i.e.
angles , one of or and one of or ) for the
3-force problem (see Fig. 7b).
The configuration of the members at every node of these
trusses is exactly the same and, therefore, they can be constructed through a process of repetition. Even though in the
examples shown, the externally loaded or constrained nodes
for 3-point and 3-force problems are in the same locations
and the tip load is applied in the same magnitude and direction for both problems, the optimal trusses have different
geometries (see Fig. 7). This is because in the 3-point problem, the directions of the reactions are not prescribed, and
they vary depending on the structure, whereas in the 3-force
problem, all of the forces are given. Since the 3-point problem has one less parameter constrained (the direction of the
reactions), the volume of the truss is always smaller or equal
to the one obtained for the 3-force problem.
In the creation of reciprocal diagrams for a 3-point or
3-force optimal truss (Fig. 8), certain geometrical similarities with its original form diagram can be observed. We
note that these geometric rules may not hold if additional
constraints are incorporated into the optimization problem,

Maxwells reciprocal diagrams and discrete Michell frames

Fig. 9 Dual optimal trusses for
the 3-force problem with
n = n , = , = ,
and = = 90 produces a
force diagram directly
proportional to its form diagram

273

FCA
FAB
C

FBC

Also, because = and = , the acting force

is parallel to the line between nodes of the reacting forces.
From the direct proportionality, it can be shown that the
lines of reaction forces in these trusses intersect at the tip
node of the truss, as the reaction at the -support (node
A-3-6-C-A) can be expressed by vector ca in the force diagram and the reaction at the -support (node C-8-7-B-C) by
vector bc (see Fig. 9).
Even more interesting is the observation that if we select
a discrete optimal truss with = and = , the
geometry of the force diagram will be proportional to a mirror of the form diagram (see Fig. 10). From Mazurek et al.
(2011) we also know that the criterion = defines
solutions where the acting forces are located along their line
of action producing structures of least volume. It is quite
remarkable that the two diagrams come together so nicely
for these optimal trusses. Thus, the ratio of the force in

such as a bound on the feasible design space. For unconstrained 3-point or 3-force problems, from the geometrical
dependencies of the lines, it can be concluded that, except
for the following three differences, the geometry of the force
diagram is the same as the corresponding form diagram:

The numbers of elements n and n at the nodes of

reacting forces are reversed in the force diagram.
The left and right turn angles and are swapped.
Angles and are replaced with and ,
respectively.

With the differences listed above, a certain family of discrete optimal structures can be described where force diagrams are directly proportional to their form diagrams.
Namely, if we select a discrete optimal truss with n = n
for a problem that produces = =
= = 90 , the force diagram will be self-reciprocal.

Fig. 10 Dual optimal trusses

for the 3-force problem with
= and = ; the force
diagram is a mirror reciprocal of
the form diagram

proportional matc

n
FCA

r line

mirro

FAB

FBC

FAB

FCA
3

FBC

n
b

274

W.F. Baker et al.

member 2-4 to the length of member B-3 is the same as the

force applied at B-1-A-B to the distance between C-A-2-4-C
and C-5-B-C. The same ratio exists between the force in
member C-5 and the length of member A-1, and so on.

6 Concluding remarks
Maxwells work on structural reciprocity and load paths
in 1864 and 1870 launched two trajectories in the theory
and design of trusses that this paper attempts to reconnect. The first trajectory was that of reciprocal diagrams
and Graphic Statics. This aspect was quickly embraced and
enlarged by Culmann, Cremona and others and widely used
by engineers as a practical method of designing and analyzing trusses. Michell, in his landmark paper Michell (1904),
starts with another aspect of Maxwells 1870 paper and
develops optimal frames of minimal total load path. The
total load path of a structure is the result of Graphic Statics
with one diagram representing the paths (lines of action) and
the reciprocal diagram representing the forces (loads). This
paper connects these two legacies of Maxwell through the
application of Graphic Statics to discrete optimal trusses. It
results in some observations worth noting:

The reciprocal diagrams of Graphic Statics provide the

information needed to determine the total load path of a
structure. This provides an avenue for determining minimum load path structures for a given connectivity by
varying the geometry of the force diagram subject to the

restrictions of reciprocal diagrams. A subsequent paper

by the authors will explore this subject in more detail.
The force diagram that corresponds to the form diagram
of an optimal discrete truss represents the geometry of
another optimal truss with possibly different external
loads. This leads to recognition that optimal trusses are
the dual of other optimal trusses, so once dual trusses
are properly paired, one can determine the forces in the
members of one truss by observing the lengths of reciprocal members in the other truss. A table of some dual
trusses is provided (see Appendix).
Certain discrete Michell Frames are self-reciprocal.
This means that by observing the geometry of certain
Michell Frames one can also determine the forces in the
members if one knows how to read the structure.
A general overview of discrete optimal trusses and their
duals is provided for the 3-point and 3-force problems.

As an extension of this work, the design of optimal bridges

and cable systems using Graphic Statics and Rankines
Theorem are currently under investigation by the authors.
Acknowledgement The second author gratefully acknowledges the
support from the National Science Foundation Graduate Research
Fellowship Program (GRFP).

Open Access This article is distributed under the terms of the Creative Commons Attribution License which permits any use, distribution, and reproduction in any medium, provided the original author(s)
and the source are credited.

Maxwells reciprocal diagrams and discrete Michell frames

275

Appendix
The following table presents a summary of the reciprocal relationships between the form and force diagrams of
several optimal structures.
Form diagram

Force diagram

Dual truss

FB

I.

a
FCA

FAB
FBC

FC

c
10

11

11

FBC

3
2

4
5
3
10 9
2
15
8
20 14
19 13
7
24 18
12
23
6
22 17
11
21 16
B

FA
5

FBC

FAB

FCA

10

4
3

a
1

1
FAB
b

FB

10

FCA

11

10

II.

9
8

III.

FA

c
FA

15
20

10

4
3

14

7
13
19
6
12
18
11
24
16 17
23
21
22

FB

15
20
14

c
7
13
19
6
12
FC
18
11
24
16 17
23
21
22
c

FAB

FC

1 c

FC

1
c
2

3
4

5
A

IV.

11

10

12

11

10

12

6
7

9
5

10
11

12
2

3
a

C
a
FCA

FBC

FA

FB

I. Classical discrete Michell solution for the centrally-loaded beam (Michell 1904; Hemp 1973; Mazurek et al. 2011)
II. Two discrete Michell solutions for semi-infinite space (Michell 1904; Hemp 1973)
III. Self-reciprocal cantilever with two points of support (Chan 1960; Mazurek et al. 2011)
IV. Optimal shear bracing solution (Hemp 1973; Stromberg et al. 2012). Note: Overlaying lines have been merged

276

W.F. Baker et al.

Form diagram

Force diagram

FAB

Dual truss

3
A

V.

1
3

FC

b
C

FCA

FA

FBC

FB
g

g
FG

FEF

FFG
G F

10

FCD
5

7
E

FGA

FA
7

5
FB

10

FE
9

8
FBC

6
5

f
FF

3
a

VI.

FAB

FDE

10
FC

FD

n n
FCA

VII.

3
6

8
C

FAB

5
4

FA

FC

B
n n

FBC

FB

A
FCA

VIII.

2
4

FBC

FAB

5
n

FA

V. Two dual minimal weight trusses given in Prager (1970)

VI. Discrete Michell cantilever truss with a circular support (Michell 1904)
VII. Discrete self-reciprocal Michell cantilever (n = n , = , = , = = 90 )
VIII. Discrete mirror-reciprocal Michell cantilever ( = , = )

b
FB

FC

Maxwells reciprocal diagrams and discrete Michell frames

References
Block P (2009) Thrust network analysis: exploring three-dimensional
equilibrium. PhD thesis, Massachusetts Institute of Technology
Block P, Ochsendorf J (2007) Thrust network analysis: a new methodology for three-dimensional equilibrium. J IASS 48(3):18
Block P, DeJong M, Ochsendorf J (2006) As hangs the flexible line:
equilibrium of masonry arches. Nexus Netw J 8(2):1324
Bow R (1873) Economics of construction in relation to framed structures. ICE Publishing, London
Chan ASL (1960) The design of Michell optimum structures. Ministry of Aviation Aeronautical Research Council Report December
(3303)
Cremona L (1890) Graphical statics: two treatises on the graphical calculus and reciprocal figures in graphical statics. Clarendon Press,
Oxford
Culmann K (1864) Die graphische statik. Meyer und Zeller, Zurich
Hemp WS (1973) Optimum structures. Clarendon Press, Oxford
Jenkin F (1869) On the practical application of reciprocal figures
to the calculation of strains of framework. Philos Mag 25:
441447
Kurrer KE (2008) History of the theory of structures: from arch
analysis to computational mechanics. Wiley-VCH, Hoboken, NJ
Levy M (1888) La statique graphique et ses applications aux constructions. Gauthier-Villars, Paris
Maxwell JC (1864) On reciprocal figures and diagrams of forces.
Philos Mag 26:250261
Maxwell JC (1870) On reciprocal figures, frames, and diagrams of
forces. Edinb Roy Soc Proc 7:160208

277
Mazurek A (2012) Geometrical aspects of optimum truss like structures for three-force problem. Struct Multidisc Optim 45(1):21
32
Mazurek A, Baker WF, Tort C (2011) Geometrical aspects of optimum truss like structures. Struct Multidisc Optim 43(2):231
242
Michell AGM (1904) The limits of economy of material in framestructures. Philos Mag 8(47):589597
Prager W (1970) Optimization of structural design. J Optim Theory
Appl 6(I):121
Rankine WJM (1864) XVII. Principle of the equilibrium of polyhedral
frames. Philos Mag 27:92
Stevin S (1586) De Weeghdaet. Inde druckerye van Christoffel Plantijn
by Francoys van Raphelinghen
Stromberg LL, Beghini A, Baker WF, Paulino GH (2012) Topology optimization for braced frames: combining continuum and
beam/column elements. Eng Struct 37:106124
Varignon P (1687) Projet dune nouvelle mechanique. Chez C.
Jombert, Paris
Varignon P (1725) Traitee du mouvement, et de la mesure des eaux
coulantes et jaillissantes: avec un traitee preliminaire du mouvement en general. Pissot [etc.], Paris
Wolfe W (1921) Graphical analysis. McGraw-Hill, New York
Zalewski W, Allen E (1998) Shaping structures: statics. Wiley, New
York
Zastavni D (2008) The structural design of Maillarts Chiasso Shed
(1924): a graphic procedure. Struct Eng Int: J Int Assoc Bridge
Struct Eng 18(3):247252
Zastavni D (2010) An equilibrium approach on a structural scale to
structural design. In: Struct arch, pp 259260