Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Civil Engineering Pre 2013

Download as pdf or txt
Download as pdf or txt
You are on page 1of 19

DO NOT OPEN THIS TEST BOOKLET UNTIL YOU ARE ASKED TO DO SO

COMBINED COMPETITIVE (PRELIMINARY) EXAMINATION, 2013

CIVIL ENGINEERING
Code No. 05

Serial No.

Time Allowed : Two Hours

A
Maximum Marks : 300

INSTRUCTIONS
1. IMMEDIATELY AFTER THE COMMENCEMENT OF THE EXAMINATION, YOU SHOULD CHECK
THAT THIS TEST BOOKLET DOES NOT HAVE ANY UNPRINTED OR TORN OR MISSING PAGES
OR ITEMS, ETC. IF SO, GET IT REPLACED BY A COMPLETE TEST BOOKLET.
2. ENCODE CLEARLY THE TEST BOOKLET SERIES A, B, C OR D AS THE CASE MAY BE IN THE
APPROPRIATE PLACE IN THE RESPONSE SHEET.
Your Roll No.
3. You have to enter your Roll Number on this
Test Booklet in the Box provided alongside.
DO NOT write anything else on the Test Booklet.
4. This Booklet contains 120 items (questions). Each item comprises four responses (answers). You will select
one response which you want to mark on the Response Sheet. In case you feel that there is more than one
correct response, mark the response which you consider the best. In any case, choose ONLY ONE response
for each item.
5. In case you find any discrepancy in this test booklet in any question(s) or the Responses, a written
representation explaining the details of such alleged discrepancy, be submitted within three days, indicating
the Question No(s) and the Test Booklet Series, in which the discrepancy is alleged. Representation not
received within time shall not be entertained at all.
6. You have to mark all your responses ONLY on the separate Response Sheet provided. See directions in the
Response Sheet.
7. All items carry equal marks. Attempt ALL items. Your total marks will depend only on the number of correct
responses marked by you in the Response Sheet.
8. Before you proceed to mark in the Response Sheet the response to various items in the Test Booklet, you
have to fill in some particulars in the Response Sheet as per instructions sent to you with your Admit Card
and Instructions.
9. While writing Centre, Subject and Roll No. on the top of the Response Sheet in appropriate boxes use
ONLY BALL POINT PEN.
10. After you have completed filling in all your responses on the Response Sheet and the examination has
concluded, you should hand over to the Invigilator only the Response Sheet. You are permitted to take away
with you the Test Booklet.
DO NOT OPEN THIS TEST BOOKLET UNTIL YOU ARE ASKED TO DO SO

EIJ-49854-A

[Turn over

ROUGH WORK

EIJ-49854-A

1.

The free-body diagram of a satellite rotating about the earth will show the satellite isolated from its
surroundings and :
(A) no force acting on it
(B) its velocity shown on it
(C) the force of gravity and centrifugal force acting on it
(D) the force of gravity, centrifugal force and its velocity

2.

The time taken by a small frictionless bead to slide on a thin wire in the gravitational field is the
minimum if the shape of the wire is :
(A) A straight line
(B) A cycloid
(C) An involute
(D) A parabola

3.

Stability of equilibrium of a body requires that :


d PE
=0
(A)
ds

d 2 PE
d PE
<0
(B)
= 0 and
ds 2
ds

d 2 PE
d PE
>0
(C)
= 0 and
ds 2
ds

(D) None of the above

4.

A rigid body, in translation :


(A) Must undergo plane motion only
(B) Cannot move on a circular path
(C) May move along a straight or curved path
(D) Can only move in a straight line

5.

The first moment of triangular area of base b and height h taken about an axis coincident with
the base is given by :
3
(A) bh

(C) bh 2

12
6

2
(B) b h

(D) h

6.

The second moment of a plane area about any axis as compared to its second moment about the
neutral axis :
(A) is always more
(B) is always less
(C) is sometimes more
(D) is equal

7.

The coefficient of restitution is defined on the basis of :


(A) Velocity components along the line of impact only
(B) Velocity component normal to the line of impact
(C) The velocity direction before and after the collision
(D) None of the above

EIJ-49854-A

[Turn over

8.

The acceleration of a particle is given by a = t3 3t2 + 5 m/s2 where the time t is in seconds.
If the Velocity of the particle at t = 1 second is 6.25 m/s and displacement is 8.8m, the Velocity
and displacement at t = 2 seconds is :
(A) 8 m/sec, 16.1m
(B) 8.5 m/sec, 16.5m
(C) 9 m/sec, 16.1m
(D) 16.4 m/sec, 8m

9.

The DAlembert principle :


(A) is hypothetical principle
(B) provides no special advantage over Newtons Law
(C) is based upon the existence of inertia forces
(D) allows a dynamic problem to be treated as a statical problem

10. The Coriolis acceleration may not vanish :


(A) if the relative velocity of the moving point becomes zero
(B) if the rotational velocity of the moving frame becomes zero
(C) if the rotational velocity of the moving frame and relative velocity become collinear
(D) if the angular acceleration of the point becomes zero
11. The ratio of effective length of compression member of steel to the approximate radius of gyration
shall not exceed :
(A) 400
(B) 350
(C) 300
(D) 250
12. Beam fixed at one end, supported at the other with uniform load as shown, then max deflection is
given by :
W
x

WL4
(A) ~185
EI
(C) ~ 185

WL3
EI

(B) ~180

WL2
EI

(D) ~180

WL4
EI

13. Poissons Ratio is a constant upto elastic limit. It is in the range of ______ for steel.
(A) 1 4 to 13

(B) 15 to 1 4

(C) 15 to 13

(D) 1 6 to 15

14. A beam of square cross section (BB) is used as a beam with one diagonal horizontal. The
location of the maximum shear stress from the neutral axis will be at a distance of :
(A) Zero
(C)

0.25 B
2

EIJ-49854-A

(B) B 4
(D) B 8
4

15. The maximum stress produced in a bar of tapering section under direct tension is at :
(A) larger end
(B) smaller end
(C) middle
(D) anywhere
16. If a composite bar is cooled, then the nature of stress in the part with high coefficient of thermal
expansion will be :
(A) Tensile
(B) Zero
(C) Compressive
(D) None of these
17. When a cantilever is loaded at its free end by a downward load, maximum compressive stress
shall develop at :
(A) bottom fiber
(B) top fiber
(C) neutral axis
(D) centre of gravity
18. The stability of a dam is checked for :
(A) tension at the base
(C) sliding of the dam

(B) over turning of the dam


(D) All of these

19. The effective thickness of a fillet weld is :


(A) S 2

(B) S1.66

(C) S1.428
where S is size of weld.

(D) S1.25

20. When a closely coiled spring is subjected to an axial load, it is said to be under :
(A) Bending only
(B) Shear only
(C) Torsion and shear
(D) None of these
21. Polar moment of inertia of a solid shaft of diameter D is :
D3
(A)
16

D2
(B)
16

D2
(C)
36

D4
(D)
32

22. When a solid shaft is subjected to torsion, the shear stress induced in the shaft at its centre is :
(A) Zero
(B) Minimum
(C) Maximum
(D) Average

EIJ-49854-A

[Turn over

23. Stiffness factor of a beam fixed at one end and simply supported at the other end for rotation at
simply supported end is :
(A)
(C)

3 EI
L

(B)

(D)

6 EI

4 EI
L

8 EI
L

24. Two simply supported beams of the same span carry the same total load. If the first beam carries
the total load as a point load at its centre and the other uniformly distributed over the whole span,
then the ratio of maximum slopes of first beam to the second will be :
(A) 1 : 1
(B) 1 : 1.5
(C) 1.5 : 1
(D) 2 : 1
25. The end rotation for the given beam is :
M
B

ML2
(A) 0.25
EI
(C) 0.25

ML3
EI

(B) 0.25

ML
EI

(D) 0.35

ML
EI

26. The total strain energy of truss element is 500 joules and it carries an axial force of 100 KN. The
extension of the member is :
(A) 1 mm
(B) 2 mm
(C) 5 mm
(D) 10 mm
27. Castiglianos theorem falls under the category of :
(A) Displacement method
(B) Equilibrium method
(C) Force method
(D) Stiffness method
28. A rod is stressed to 50 KN/mm2 in tension. The E for the rod is 200 KN/mm2. The strain energy
per cubic meter will be :
(A) 6.25109
(B) 5.0109
(C) 2.5109
(D) 1.25109
29. The rotation of the free end of a cantilever beam due to a 5 kN load is 0.001 rad. Then the
deflection of the free end due to a moment of 120 kNm is :
(A) 1.2 mm
(B) 2.4 mm
(C) 3.6 mm
(D) 4.8 mm

EIJ-49854-A

30. The fixed end moment MFAB for the beam shown in the Fig below is :
W
A

10 W L2
(A)
192

B
L/2

L/2

11 W L
(C)
48

31. Moment distribution method is best suited for :


(A) Indeterminate pin jointed truss
(C) Space frames

(B)

5W L
48

(D)

W L2
48

(B) Rigid frames


(D) Trussed beam

32. The carry-over factor for a prismatic beam element with far end fixed is :
(A) 1
(B) 0.5
(C) 0.33
(D) 0.25
33. The column analogy method is applicable for the indeterminate structure having maximum redundancy
equal to :
(A) 1
(B) 2
(C) 3
(D) No limitation
34. The number of unknowns to be determined in the stiffness method is equal to :
(A) Static indeterminancy
(B) Kinematic indeterminancy
(C) Sum of static and kinematic indeterminancy (D) None of the above
35. Which of the following sections will have maximum shape factor ?
(A) Square
(B) Circular
(C) Diamond
(D) Triangle
36. The shape of influence line diagram for the bending moment at mid span in a simply supported
beam is :
(A) Rectangular
(B) Triangular
(C) Parabolic
(D) Circular
37. The Muller-Breslau principle for influence line is applicable to :
(A) Simple beam
(B) Continuous beam
(C) Redundant truss
(D) All of the above
38. The variation of influence line for vertical support reaction of a statically determinate beam is :
(A) Linear
(B) Parabolic
(C) Circular
(D) None of the above

EIJ-49854-A

[Turn over

39. The area of the influence line diagram for the reaction at the hinged end of a uniform propped
cantilever beam of span L is :
(A) L 2

(B) 3L 8

(C) L 4

(D) L 8

40. The total area of the influence line diagram for shear force at mid span in a simply supported beam
of span L is :
2
(A) L 8

(B) Zero

2
(C) L 2

(D) L 2

41. A twohinged parabolic arch is subjected to a temperature rise of t0 C, then the horizontal
thrust at the support will :
(A) increase
(B) decrease
(C) remain same
(D) increase or decrease
42. The line of thrust in a Parabolic arch is :
(A) Funnicular Polygon
(C) Triangular

(B) Parabolic
(D) Circular

43. The simply supported bending moment at the central hinge of a three hinged arch is 36 kNm. The
span and rise at the hinge are 12 m and 3 m respectively. The horizontal thrust in the arch is :
(A) 3 kN
(B) 6 kN
(C) 9 kN
(D) 12 kN
44. In approximate analysis of building frames under lateral loads, the point of inflection in beams and
columns is assumed at :
(A) Span / 2
(B) Span / 3
(C) Span /10
(D) Span / 20
45. The effective slenderness ratio of a cantilever column of length L :
(A) 0.5 L/r
(B) L/r
(C) 2 L/r
Where, r = radius of gyration.

(D) 2 L/r

46. A 40 cm diameter circular timber column is 4 m long (effective). The slenderness ratio of the
column is :
(A) 10
(B) 20
(C) 40

EIJ-49854-A

(D) 20 2

47. A soil sample (sp. gr 2.7) has a degree of saturation of 40 % at water content of 20%. The void
ratio of the sample is :
(A) 1.35
(B) 0.03
(C) 5.4
(D) None of these
48. Sieving is not carried out for grain sizes smaller than about :
(A) 0.75 mm
(B) 0.075 mm
(C) 0.150 mm
(D) 0.20 mm
49. If sand is in its densest state, its relative density is :
(A) Zero
(B) 1
(C) Less than 1
(D) Greater than 1
50. The ratio of the shear strength of undisturbed soil to that of remoulded soil is known as the :
(A) liquidity index
(B) activity index
(C) relative consistency
(D) sensitivity
51. Talus is a soil transported by :
(A) Wind
(C) Glaciers

(B) Water
(D) Glacial tills

52. Darcys Law is applicable if a soil is :


(A) incompressible
(C) isotropic

(B) homogeneous
(D) All of these

53. The hydrostatic pressure on a phreatic line equals :


(A) Atmospheric
(B) Less than Atmospheric
(C) Greater than Atmospheric
(D) None of these
54. Liquefaction can be prevented by :
(A) providing filters
(B) increasing the seepage length of the flow
(C) lowering the water table
(D) All of these
55. The horizontal Geostatic stress at a depth of 4m in a uniform deposit of soil having Kb = .5 and
b = 16.5 kN/m3 is :
(A) 16.0 kN/m2
(B) 22.0 kN/m2
(C) 33.0 kN/m2
(D) 66.0 kN/m2
where Kb is Boussinesqs influence factor.
56. The shear stress below a point load of 2 tons at a depth 4m in a soil mass is :
(A) Zero
(B) 2 t/m2
2
(C) 1t/m
(D) None of these
EIJ-49854-A

[Turn over

57. If the coefficient of volume change and the coefficient of permeability of a soil mass are
2.9110-4 m2/kN and 3.410-5 m/sec then the coefficient of consolidation will be :
(A) 11.9110-3 m2/sec
(B) 3.6210-3 m2/sec
(C) 9.8210-4 m2/sec
(D) 9.8910-9 m2/sec
58. If instead of single drainage, the number of drainage faces are increased to two, the rate of
compression will be :
(A) 4 times slower
(B) 2 times slower
(C) 4 times faster
(D) None of the above
59. After the complete consolidation of a soil mass, the effective stress becomes equal to :
(A) the pore water pressure
(B) the neutral stress
(C) Both of these
(D) None of these
60. Sheep foot roller is ideally suited for the compaction of :
(A) cohesive soils
(B) cohensionless soils
(C) both types of soils
(D) None of these
61. An unconfined compression test is good for :
(A) Granular soils
(C) Both granular and cohesive soils

(B) Saturated cohesive soils


(D) None of these

62. A deviatoric stress is given by :


(A) 1 + 3
(C)

1 + 3
2

(B) 1 3
(D)

63. The maximum pressure intensity which a soil can carry without shear failure is known as its :
(A) safe bearing capacity
(B) ultimate bearing capacity
(C) net safe bearing capacity
(D) net ultimate bearing capacity
64. The bearing capacity factor for local shear failure, are determined with respect to :
(A) average c and parameters
(B) increased c and reduced parameters
(C) decreased c and increased parameters
(D) reduced c and parameters
65. The viscosity of the grout pumped into weak soil depends directly on the :
(A) specific gravity of the soil
(B) shear strength of the soil
(C) permeability of the soil
(D) degree of saturation of the soil

EIJ-49854-A

10

66. In a plate load test, the ultimate load is estimated from the load-settlement curve on a log-log
graph :
(A) Directly
(B) By drawing tangents to the curve at the initial and final points
(C) By the secant method
(D) Simply at 0.2% of the maximum settlement

2c cot

67. Pile foundations are provided to :


(A) carry loads
(C) compact a loose cohesionless deposit

(B) resist horizontal and uplift forces


(D) All of these

68. The efficiency of pile group depends on :


(A) soil type
(C) pile spacing

(B) method of pile installation


(D) All of these

69. The method of slices was first suggested by :


(A) Taylor
(C) Fellineous

(B) Bishop
(D) Terzaghi

70. A slope is considered infinite when :


(A) its length in the third dimension is infinite
(B) the slant height is very large
(C) the base of embankment is very long
(D) All of these
71. To have zero active pressure intensity at the top of a wall in cohesive soil, one can apply a
uniform surcharge of intensity :
(B) 2c tan
(A)
(C) 2c cot

(D) 2c tan

72. An unsupported vertical cut may be made in cohesive soil to a height of :


(A)

2c
tan 45 +
2

(B)

2 qu
tan 45 +
2

(C)

4 qu
tan 45
2

(D)

4c
tan 45
2

73. The pressure diagram below the dredge line of an anchored sheet-pile wall embedded in
cohesionless soil is :
(A) rectangular
(B) triangular
(C) triangular then rectangular
(D) parabolic

EIJ-49854-A

11

[Turn over

74. Dynamic Magnification factor is the ratio of :


(A) static force to dynamic force
(C) dynamic deflection to static deflection

(B) dynamic force to static deflection


(D) dynamic force to static force

75. The Westergaard equations are used for analysis of :


(A) clayey soils
(B) sedimentary soils
(C) black cotton soils
(D) cohesionless soils
76. Under reamed piles are normally :
(A) Precast piles
(C) Driven piles

(B) Bored piles


(D) Sunken piles

77. A lubricant 100 times more viscous than water would have a viscosity (in Pa-s) :
(A) 0.01
(B) 0.1
(C) 1
(D) 10
78. Kinematic Viscosity and specific gravity of a certain liquid are 5.58 stokes and 2 respectively. The
viscosity of liquid in S.I. unit are :
(B) 1.315 Ns/m2
(A) 1.116 Ns/m2
(C) 1.489 Ns/m2
(D) 1.652 Ns/m2
79. In the laminar boundary layer flow over a flat plate, the ratio (/x) varies as :
(A) Re

(B)

Re
(C) 1/Re
(D) Re
where is the boundary layer thickness and X is the distance from the leading edge in the direction
of flow.

80. The turbulence in which the products and squares of the velocity component and their derivatives
are independent of direction is called :
(A) isotropic
(B) potential
(C) anisotropic
(D) laminar
81. The laminar boundary layer thickness varies as :
(A) x1/2
(C) x1/7

(B) x1/2
(D) x6/7

82. For psedoplastic fluid, flow consistency index is :


(A) < 1
(C) > 1

(B) = 1
(D)

EIJ-49854-A

12

83. If the fluid entering the pipe is turbulent and the velocity in the tube is above critical the transition
length is :
(A) 40 to 50 times the pipe diameter
(B) 10 to 30 times the entering velocity
(C) 20 to 30 times the pipe diameter
(D) None of the above
84. If the pressure on the surface of an oil (s.g = 0.8) tank is 0.1 kg/cm2, the pressure head at a depth
of 2.5 m is :
(A) 1 m of water
(B) 2 m of water
(C) 3 m of water
(D) 3.5 m of water
85. A vertical rectangular plane surface is submerged in water such that its top and bottom surfaces are
1.5 m and 6.0 m respectively below the free surface. The centre of pressure below the free surface
will be at a depth of :
(A) 3.75 m
(B) 4.0 m
(C) 4.2 m
(D) 4.5 m
86. A jet strikes a stationary plate normally with a velocity of 8 m/s and the plate suffers a force of
120 N. The power obtained, in kW is :
(A) 0.96
(B) 9.4
(C) Zero
(D) 958
87. Which of the following is a dimensionless number ?
(A) Mannings coefficient n
(B) Pipe friction factor f
(C) Chezs coefficient C
(D) HazenWilliam coefficient CH
88. The momentum correction factor for laminar flow through a circular pipe is :
(A) 1.5
(B) 2.0
(C) 1.67
(D) 1.33
89. The continuity equation is based upon the principle of :
(A) Conservation of energy
(B) Conservation of momentum
(C) Conservation of mass
(D) None of these
90. For a hydraulically efficient rectangular channel of bed width 4.0 m, the depth of flow is :
(A) 4.0 m
(B) 8.0 m
(C) 1.0 m
(D) 2.0 m
91. For an error of 10% in the measurement of head over a broad crested weir, the error in discharge
will be :
(A) 10 %
(B) 5 %
(C) 15 %
(D) 25 %

EIJ-49854-A

13

[Turn over

92. The flow will be in supercritical state in the following profiles :


(A) M3, S3 and M1
(B) M2, S1 and M3
(C) S2, S3 and M3
(D) S1, S2 and S3
93. In a Sutro weir, discharge is proportional to :
1/2
(A) H
3/2
(C) H

(B) H
5/2
(D) H

94. A pump is required to deliver 150 L/s at a head of 45 m when running at 1750 r.p.m. The specific
speed of the pump is :
(A) 17.4
(B) 39.0
(C) 89.0
(D) 1233.0
95. Water is pumped through a pipeline to a height of 10 m at the rate of 0.1 m3/s frictional and other
minor losses are 5 meter. Pumping power required, in kW is :
(A) 14.70
(B) 9.80
(C) 20.0
(D) 13.3
96. Theory of probability is applied to :
(A) accidental error only
(C) both accidental and cumulative

(B) conditional error


(D) residual error

97. The shrinkage factor of an old map is 24/25 and R.F is 1/2400 then the corrected scale for the
map is :
(A) 1/2400
(B) 1/2500
(C) 1/600
(D) 1/60000
98. If the length of a chain line along a slope of is l the required slope correction is :
(A) 2l cot2 /2
(B) 2l sin2 /2
2
(C) l tan /2
(D) l cos2 /2
99. Which of the following is the most precise instrument for measuring horizontal distances ?
(A) Metallic Tape
(B) Steel Tape
(C) Tacheometer
(D) Tellurometer
100. The whole circle bearing of a line, whose quadrantal bearing is S19 30 E is :
o
o
(A) 19
(B) 199
o
(C) 160
(D) None of the above
o

101. The value of dip at the magnetic pole is :


o
(A) 0
o
(C) 90

EIJ-49854-A

(B) 45
(D) None of these

14

102. The difference between face left and face right observations of a theodolite is
(A)
(B)
(C)

, the error is :

(D)

103. The closing error can be balanced by :


(A) Bowditch rule
(C) Working accurately latitudes

(B) Transit rule


(D) Either (A) or (B) as applicable

104. If N is the number of stations and the least count of the instrument is
closure in traversing should not be :
(A) < 20 N
(B) > 20 N
(C) < 20

, then the limit on the angular error of

(D) > 20 N

105. What will be the correction for curvature for a distance of 1000 m ?
(A) .0673 m
(B) .0785 m
(C) .0568 m
(D) None of these
106. The reading on a 4.0 m staff at a point is observed as 2.895 m. If the staff was 8 cm out of the plumb line, the
correct reading should have been :
(A) 2.8800 m
(B) 2.8937 m
(C) 2.8600 m
(D) 2.9937 m
o

107. If the degree of a curve is 1 and if chain length is 30 m, then the radius of the curve is equal to :

130
3
0
245
0N
(A) 5400 m
(B) 1720 m
1720
5400
(C)
m
(D)
m

108. The long chord and tangent length of a circular curve of radius R will be equal if the angle of deflection is :
o
o
(B) 60
(A) 30
o
o
(C) 150
(D) 120
109. If the radius of a circular curve is five times the length of a transition curve then the spiral angle is given by :
(A) 1/5 rad
(B) 1/10 rad
(C) 1/20 rad
(D) 1/40 rad
110. The resultant of two forces P and Q is R. If Q is doubled, the new resultant is perpendicular to P, then :
(A) P = R
(B) Q = R
(C) P = Q
(D) None of the above is correct

EIJ-49854-A

15

[Turn over

111. The mass moment of inertia of a rectangular plate of mass M and sides a and b about an axis perpendicular to
plate through its centre is :
(A)

M 2
(a + b 2 )
3

M 2
(a + b 2 )
(C)
12

(B)

M 2
(a + b 2 )
4

a 2 b2
(D) M +
4 12

112. Two circular discs of same weight and thickness are made from metals having different densities. Which disc will
have the larger rotational inertia about its central axis ?
(A) disc with larger density
(B) disc with smaller density
(C) both discs will have same rotational inertia
(D) None of the above
113. For a body subjected to hydrostatic static state of stress, the shear stress on a plane inclined at an angle of 45
with the horizontal will be :
(A) maximum
(B) minimum
(C) zero
(D) 50% of hydrostatic pressure

114. For the flow to be definitely laminar in a pipe, the value of Reynolds number should be :
(A) < 2000
(B) 2500
(C) 5000
(D) > 5000
115. For critical flow in a rectangular channel for a discharge per unit length of 25 cumec, the critical depth will be :
(A) 2.1 m
(B) 1.5 m
(C) 4 m
(D) 2.75 m
116. The intensity of pressure developed by surface tension of 0.0075 Kg/m in a droplet of water of 0.075 mm
diameter is :
(A) 0.08 Kg/cm2
(B) 0.06 Kg/cm2
(C) 0.04 Kg/cm2
(D) 40 Kg/cm2
117. If there are n pipes of same diameter d laid in parallel in place of a single pipe of diameter D,
then :
(A) d =

D
n2/5

(B) D =

(C) d =

D
n2/3

(D) d =

EIJ-49854-A

16

d
n2/5

D
n1 / 5

118. If Fr is the Froude number for a flow in a triangular channel, then the Froude number for same velocity and same
depth of flow in rectangular channel will be :
(A) Fr
(C)

Fr
2

119. Shape factor is a property which depends :


(A) only on the ultimate stress of the material
(C) both on yield and ultimate stress of material

(B)
(D)

2 Fr
Fr
3

(B) only on the yield stress of the material


(D) only on the geometry of the section

120. The rigid-jointed plane frame shown in figure will :


(A) sway to left
(B) sway to right
(C) not sway at all
(D) may sway to left or right
depending upon the magnitude of Udl
EI = Const.

EIJ-49854-A

17

[Turn over

ROUGH WORK

EIJ-49854-A

18

ROUGH WORK

EIJ-49854-A

19

150

You might also like