Sha-Shib Aerospace Engineering: Workshop Practices
Sha-Shib Aerospace Engineering: Workshop Practices
WORKSHOP PRACTICES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
c) Curved form
d) Straight form
Which material for belts is waterproof, acid proof and alkali proof but restricted to only low temperature
a) Balata belts
b) Rubber belts
c) Cotton or fabric belts
d) Plastic belts
c) 22
d) 30
c) Square shank
b) Circular shank
A screw thread which has an included angle of 29 and can transmit power in both the directions is:
a) Buttress thread
b) Acme thread
c) Sharp V threads
High speed drills are made of:
a) Alloy steel
d) Square Thread
c) Round file
d) Cabinet file
The type of gear which can be used for high speed reductions is:
a) Bevel gear
b) Herringbone gear
c) Spur gear
d) Internal gear
Dedendum is:
a) Addendum+ addendum
c) Clearance + addendum.
d) Clearance - addendum
c) Mild steel
b) High carbon steel hardened & tempered c) High carbon steel hardened at the tip
b) Addendum clearance
c) Yellow
d) Green
c) 109
d) 110
c) 0.01
d) 0.01mm
c) Torsion type
d) Combination wrench
The type of punch which is used for marking deep holes or pop spots is:
a) Prick punch
b) Drift punch
c) Center punch
b) Minus thread
c) Tolerance thread
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
The type of fit which has got highest amount negative allowance is known as:
a) Shrink fit
b) Snug fit
c) Tight fit
d) Wringing fit
c) Thrust bearing
The bearing which takes good radial loads but thrust loads only in one direction:
a) Tapered roller bearing
b) Spherical roller bearing
c) Ball bearing
Twisting in a chain can be checked by:
a) Stretching it tight n checking for the bends
b) Freely suspending it
c) Rolling it slowly around the finger
The telescoping gauge can be used to measure the _____ dimensions:
a) External
b) Curved external dimensions
d) Float bearing
c) Internal
The drill which has no rake angle to the flutes and used for cutting through thin sheet metals:
a) Twist drill
b) Step drill
c) Flat drill
Precision instruments are made of:
a) High carbon steel
b) Alloy Steel
While checking micrometer accuracy, the zero of the thimble was found above the datum line. This error is said to:
a) Positive error and it must be added
b) Negative error and the amount must be added
c) Negative error and must be subtracted
d) 0.050mm
c) 0.5mm
For an accuracy of up to 0.001 & a longer range the instrument suitable is:
a) Micrometer
b) Vernier Calipers
c) Dial test indicator
d) Steel rule
c) V thread
d) Buttress
The tool which is used to enlarge and give an accurate dimension to a hole:
a) Drill
b) Round file
c) Tap
c) Feeler gauge
d) Radius gauge
d) None is correct
The TPI of a hacksaw blade where you require a faster but a smooth cutting in not required:
a) 32 TPI
b) 24TPI
c) 14 TPI
d) 18 TPI
The most common types of file grades which are used for removing stock and provide good finishing quickly are:
a) Bastard & smooth file
b) Bastard & Second Cut
c) Coarse file & dead smooth
The type of wrench which has both the openings of equal size
a) Adjustable wrench
b) Dual sided Open wrench
c) Combination wrench
c) Combination pliers
To protect the finished surfaces while using a vice ____ maybe used:
a) Steel Caps
b)Alloy steel caps
47.
48.
The type of belt which provides you with negligible slippage and quieter operation is:
a) V-belt drive
b) As in (a) & also has a high velocity ration (i.e., up to 10:1)
c) Flat belt drive
d)
49.
50.
51.
52.
53.
54.
55.
The gear used to counteract the effects of side thrust in helical gears is:
a) Internal gear
b) Spur gear
c) Helical gear
c) Prick punch
57.
58.
The pliers which uses compound leverage mechanism to multiply the amount of forces:
a) Nose pliers
b) Vice grip pliers
c) Diagonal pliers
61.
62.
63.
64.
d) Center punch
c) Torsion springs
60.
The type of gear which can be used for transmission of power to a shaft parallel to it or to a shaft which is at an angle
a) None, gears can only transmit at a single angle
b) Helical gear
c) Spur gear
56.
59.
d) Herringbone Gear
The distance to which a tooth extends into the tooth space in a meshing gear is known as:
a) Working depth
b) Whole depth
c) Whole depth + clearance
The punch which is used to cut circular holes in thin sheet metal is:
a) Drift punch
b) Hollow punch
b) Nickel Alloy
d) Duckbill Pliers
d) Chrome-vanadium steel
c) Peening
d) Fine thread
In a 24/25 vernier caliper, __ main scale graduations are divided into __ vernier scale graduations:
a) 25 & 24
b) 24 & 25
c) 50 & 25
d) 49 & 25
d) Outside jaws
65.
66.
67.
68.
A tool which is used to remove the burrs on the external thread is:
a) Split die
b) Die plate
c) Die Nut
d) None, are to be removed by a sharp object
d) none
The type of thread which gives you a tighter grip, finer adjustments and more resistance to vibration:
a) Coarse thread
b) Rough pitch
c) Buttress thread
c) Adjusting nut
d) Bevel gear
69.
70.
71.
The type of spring assembly where the extension remains the same is:
a) Springs in series
b) Springs in parallel
c) Both the assembly provides same extension
d) None
72.
73.
74.
75.
76.
77.
The type of gauge which is used to determine the diameter of a cylindrical part is:
a) Telescoping gauge
b) Plug gauge
c) Tap gauge
d) Ring Gauge
78.
The type of gauge used to measure small clearances between two surfaces is known as:
a) Radius gauge
b) Feeler gauge
c) Telescoping gauge
d) Vernier gauge
79.
Which type of reamer can be adjusted back to its original diameter even after wearing out:
a) Chucking expansion reamer
b) Jobbers reamer
c) Bottoming reamer
d) Chucking flat reamer
80.