G0cwa sdr3

THE MINNIE RTL SDR
By Nick G0CWA Sept 2012
Hi this is my latest design for a RTL-SDR communications receiver. The set amounts to little more
than a switchable receive up converter. Although designed for the Realtek RTL2832U Chipset +
Elonics E4000 tuner, it will work with any of the other compatible tuners. I would personally
recommend SDR# as the control package for the dongle.
http://sdrsharp.com/
The frequencies from DC to ~1.7GHz are covered in two ranges:
High range ~60MHz to 1.7GHz (depending on tuner chip) with the normal gap around 1.1GHz
And
Low range DC to 60MHz.
The main aim was to build a version of my designs to comfortably fit into a Lap top bag and be fully
portable and powered from the PC USB port. The completed unit including a dongle fits into a small
die-cast instrument case measuring only 55x25x125mm. To keep the circuitry size to a minimum I
have not included any extras e.g. pre-amp or antenna switching etc.
There is nothing clever or particularly original in the design with one exception the use of a 125MHz
conversion oscillator so avoiding the VHF broadcast band on the output and reducing any sensitivity
issues. The 5V supply is taken off the dongles USB connector by opening up the dongle case,
carefully, and soldering a fine insulated wire to the appropriate USB connecter pin taking this out
through a small opening cut in the side of the dongle case.
Follow my track layout and use top quality miniature co-ax for maximum sensitivity I used silver
plated. Do NOT use single strand wire for any RF signals as these dongles are very sensitive to mismatches and unless you are very lucky will shut down and work poorly, if at all. Note I have
presented the track layout as an X-ray view, remember to mirror it if needed for the copper side
You may notice that D1, D2, C11 and C12 do not appear on the PCB top they are actually soldered on
the underside of the board to save space. There are also two wire links on the top of the PCB to add.
The RF input to the dongle is via a connector shown in the real world PCB layout diagram above.
This connector was scavenged from a cheap plastic bodied co-ax plug which is soldered to the PCB
in a small slot. TAKE NOTE the connector is soldered on both sides bridging the two earth pads to
complete the ground track to both sides of the PCB; the centre pin is connected via a small piece of
copper wire to the PCB.
The only problem I had was when switching between the receive bands sometimes the dongle
would lock up, this was due to the current demands of the relays and smoothing caps I managed to
cure this problem by reducing the values of C11 and C12 anything above 100 nF should be ok.
The actual PCB dimensions and cut-outs suited both my box and gave sufficient clearance for the
dongle, antenna socket and switch. Adjust these to suit your case etc.
The coils are all 6.5 turns of ~1mm diameter copper wire 0.25 inch diameter by 0.4 inch long, the
relays are both NEC/TOKIN UB2-5NE 5V Coil DP Ch-over types although any similar equivalent ones
may be used. The regulator is an LM1117T 3.3V unit. The crystal oscillator is a 3.3V 125MHz crystal
oscillator module, any oscillator module frequency above 60MHz can be used but I cant guarantee
the receivers performance or immunity to de-sentisation/interference from the VHF broadcast
bands.
For any further information about operation and performance check my MK2 design write up also
on this site at
http://makearadio.com/visitors/nick-sdr2.php
Enjoy this design hope you find it of use, as always I can be contacted at:
n.strong@hotmail.co.uk
The Radio board and QRZ forums
Please only contact me via these routes if you have any questions, I cant guarantee to reply
otherwise as I cant see every reference to my sets.
Enjoy the design 73 for now Nick G0CWA
PLEASE NOTE if you downloaded this document from anywhere but
http://makearadio.com
or
http://makearadio.com/visitors/nick-sdr2.php
I can not guarantee you will have the latest version, Please inform Dave if it was downloaded from
another site. Daves site is the ONLY ONE I HAVE AUTHORISED to distribute/display my projects and
documents. However links to the projects are permitted with Daves permission.

G0cwa sdr3

Uploaded by

Copyright:

Available Formats

G0cwa sdr3

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

G0cwa sdr3

Uploaded by

Copyright:

Available Formats

THE MINNIE RTL SDR

By Nick G0CWA Sept 2012

You might also like