Haz Metal Do Galt As

Natural Stone Fixing Systems
Product Catalogue
Your Fixing Systems Specialist
Contents
Company role
1-2
Natural stone xing system overview
3-4
Design rinciplesP
5-6
HZ Z Anchor Fixing System

Introduction
Installation
ail
det
HZ01 echnical t
ails
det
HZ02 echnical t
ails
det
10
HZ05 echnical t
ails
det
11
HRS1 echnical t
ails
det
12
HZ02-S echnical t
Special
ails
det
horsZ
13
Anc
14
AXO Body Anchor Fixing Systems

Introduction
15
Installation
ail
BA echnical t
det
ails
AXO1&2 echnical t
16
det
17
ails
det
18
AXO3 echnical t
ails
det
19
AXO4 echnical t
ails
det
20
HRS3 echnical t
ails
det
21
Special
hors
Body Anc
22
HA L Anchor Fixing Systems

Introduction
Installation
23
ail
HA01 echnical t
det
ails
24
det
25
HA02&HA03 echnical t
ails
det
26
HA04&HA05 echnical t
ails
det
27
Special
horsL
Anc
28
HDM Mortar Anchor Fixing Systems

Introduction
Installation
29
ail
det
30
BUN & BUG technical details
31
BTN & BTG technical details
32
MTN & MTG technical details
33
HN & HG technical details
34
HSD Mortar Anchor Fixing Systems

Introduction
35
HRD01 echnical t
ails
det
HSD anchor technical details
35
36
HMP Sub Channel Systems

Introduction
Installation
37
ail
det
38
ATS channel system introduction
39
HMP channel technical details
40
HCSP channel restraint technical details
41
HCRS channel restraint technical details
42
HMP Sub Channel Systems examples
43
Special Sub Channel Systems
44
Heavy Duty Fixing Systems
45
Aluminium
46
HCA
HAZ
ner
nnel Cha
stems Sy
Cor
hors Anc
47
cessories
Ac
48
HB Expansion Bolts
HB01, HB03 & HB05 technical details
49
HB06, HB07 & HB09 technical details
50
References
Eurocode
Technical
HAZ Metal Sanayi ve Ticaret A.S. All rights reserved. March 2011
51-52
ept Conc
esign
ormation
Inf
53
Sheet
54
|1
Natural Stone Fixing Systems - Overview
Company Profile
Introduction
Mission Statement
HAZ Metal is located in Iskenderun, in the southern part of Turkey,

based in the company owned property, with an area of 17.000 square
meters. The company provides services in the design and production
of stainless steel fixing systems for natural stone installation and
a variety of products used in construction.
To design and produce products that exactly meet the expectations

of our clients and provide them with technical service in order to
assist them with their requirements. Our objective is to propose the
most secure, economical and easy to use fixing systems to satisfy
our clients.
The companys objective is to assist and advise its clients in choosing the most suitable fixing systems for their requirements and to
provide them with quality production and supply with timely
deliveries.
Product Range
HAZ Metal has dedicated itself to supplying its clients with easy to
use, secure and economical fixing systems. Along with this
principle, HAZ Metal has organized a technical department to design and produce fixing systems in accordance with international
standards.
HAZ Metal has 200 employees working both in Turkey and in foreign
branches. Along with a sales office in Istanbul, Turkey, there are
HAZ branches in the United Arab Emirates, Germany, the United
Kingdom, Russia, Qatar, Egypt and Singapore. With this network,
HAZ Metal reaches out closer to their clients, to provide better
services to meet local requirements.
The innovative design and production techniques offer practical
and economic solutions to solve every possible problem within the
scope of natural stone installation. As a supplier of fixing systems
to major projects around the world, HAZ Metal has proven its quality
and reliability to its clients. The company enjoys serving the sector
and works hard to constantly improve and develop its services.
HAZ Metal started producing fixing systems in 1993. Today, the

company has the technical know how and technology to produce all
types of natural stone fixing systems used for ventilated stone facades.
Production of a variety of fixing systems such as channels, cast-in
channels, masonry support anchors and expansion bolts is also
available.
Sub channel systems.
Cast in channel systems.
Framing systems.
Masonry support systems.
Structural Building components.
Expansion bolts.
Various contruction accessories.
Standard and customized production is made to meet the special
application requirements. Products are produced from stainless steel
and galvanized steel raw material. Stainless steel grade 1.4301
(AISI304) & 1.4401 (AISI 316) and galvanized mild steel are used in
the production of fixing systems.
|2
Technical Service
Production Capacity
HAZ Metal provides services in the design of xing systems and

preparation of structural calculations. This service is done in the
company technical department using CAD software and SAP
engineering programs.
With approximately 10.000 sqm of production halls, HAZ Metal

is equipped with 120 work stations and has a monthly production
capacity of more than 500 tons.
The companys technical staff consists of experienced engineers who

are competent in the eld. Our engineers provide services in design,
anchor positioning, preparation of shop drawings and scheduling.
The technical department receives the necessary technical information of the project in order to design the most suitable, secure, easy
to use and economical fixing systems in accordance with the project
criteria. Custom design and production is also made after receiving
detailed architectural drawings of the project.
HAZ Metal provides the necessary documentation and structural
calculation reports for submittal in order to approve the designed
xing systems.
Quality Standards
HAZ Metal implements internationally recognised standards in the
design and production of xing systems. Product design and production is strictly controlled within the specications of these standards.
All products are designed and produced by its personnel, applying
the latest production methods with modern machinery. In order to
guarantee outstanding quality to their clients, HAZ Metal has
established a testing laboratory at the factory, to inspect materials
during each stage of production.
Throughout the years, production techniques and methods have

been improved to achieve higher quality and productivity. HAZ
Metal today implements modern technology in the production of
xing systems in order to meet the requirements of the industry.
The factory is equipped with a coil slitting machine, channel roll
formers, press breaks, eccentric presses, automated end part
formers, thread rolling machines, cold forge bolt makers and
various production units. There is also an in house electro
galvanizing unit where 12 micro thick zinc coating on mild steel
is made. Hot dip galvanizing with over 50 micro thick zinc coating
is made by prequalied sources outside the factory.
Emphasis has also been given to automation in which faster
production and lower costs are achieved by higher efciency. HAZ
Metal is able to desing and build apparatus and progressive dies
in order speed up production.
The presence of a work shop with the capability of preparing and
maintaining the required moulding and tooling, provides exible
production. The quick preparation, maintenance, alteration and
adjustment of machines and toolings are made without
interrupting the production process which leads to saving time
and costs. This enables fast and exible production to supply
projects of any size.
|3

HZ Z Anchor Fixing System
Fixing systems need to accommodate all types of backing
walls whether they are concrete walls, block work & masonry
walls or steel structures.
The following points are taken into consideration when
designing a xing system for natural stone installation.
Stone dimensions.
Cavity structure: projection size and isolation.
Application type: horizontal or vertical joint installation.
Joint size.
Structural wall backing.
Height of facade.
Relevant dynamic loads such as wind and seismic loads.
Design criteria of the project.
HAZ Metal proposes and specially designs xing systems
according to individual projects requirements.
Fixing to concrete with bolts.

Projection sizes up to 135mm.
Recommended for loads up to 800N.
Installation at horizontal or vertical joints.
Three dimensional adjustability.
AXO Body Anchor Fixing

Projection sizes up to 260 mm.
Recommended for loads up to 1300 N.
Optimum static performance.
Direct xing to concrete

walls with bolts
Fixing to concrete with bolt
anchors using expansion bolts.
Insulation is cut at each
anchoring point.
HA L Anchor Fixing System

Can be used for 50 mm and larger stone
thicknesses.
Various types to enable adjustability.
Installation at horizontal joints only.

or masonry walls with
mortar
Fixing to concrete with mortar
anchors using mortar.
Insulation is drilled at each
anchoring point.
Indirect xing to load

bearing beams with
channel system
Fixing to sub channel
structure supported to load
bearing beams. Insulation is
cut at each anchoring point.
HSD Mortar Anchor Fixing System
Fixing to masonry with mortar.

Various types to t a range of loads and
projection sizes.
HMP Sub Channel System

Fixing to sub channel structure which is
attached to load bearing beams.
High load bearing capability to t projection
sizes
up to 360 mm.
Greater projection sizes are achieved with
special design.
Fully adjustable and allows fast installation.
|4

HAZ Metal is known as a high quality and reliable service provider for the design and supply of xing systems in the construction industry. Major
projects have been successfully supplied with HAZ Metal xing systems. The main advantage of HAZ Metal is the ability to custom design xing
systems and provide fast production to meet the time restraint requirements of projects. The design and supply is done in accordance with
international standards and more importantly withour customers expectations.
Application examples for bolt anchors

Anchors are xed on to load bearing walls
with expansion bolts.
To fasten anchors on to isolated walls, the

isolation must be cut rst. After fastening, the
cut out isolation piece must be inserted back,
and the isolation parts must be sealed in order
to reduce cold bridging.
Application examples of prole systems

The channels are fastened to channel supports
which are xed with expansion bolts to oor
beams. Natural stone panels are xed with
anchors which are xed to channels with hex.
bolt sets. This system allows installation to be
independent from the wall. Low anchoring
points allows faster installation and reduces
cold bridging.
|5
Design Principles
Design & Calculation Standards
Reference is made to the following standards:
HAZ Metal provides services in the

design of xing systems and the
preparation
of
structural
calculations. This service is done
in the company technical
department using CAD software
and SAP engineering programs.
British Standards;
BS 8298
EN 10088-2
BS 6105
BS 5950
BS 6399Part2
BS 970 Part 3 1991, M
German Standards;
DIN 1045
DIN 1053
DIN 1055
DIN 4114
DIN 18 516
DIN 18 800
DIN 18 801
American Standards;
ASTM A 276
ASTM 666
Our technical department receives the necessary technical

information of the project in order to propose the most suitable,
secure, easy to use and economical xing systems in accordance
with the project criteria. Custom design is also made in accordance
with the architectural drawings of the project.
HAZ Metal provides the necessary technical documentation for
submittal to the project ofcials in order to receive approval for
the xing system elements. The following principles are used in
the design and structural calculations for natural stone xing
systems.
Design Factors
Design and installation of natural stone cladding.

Steel plates, sheets and strips stainless and heat resisting.
Corrosion resistant stainless steel fasteners.
Structural use of steel work in building.
Wind loads.
Mechanical properties for stainless steel.
Concrete and reinforced concrete, design and dimensioning.
Masonry, design and dimensioning.
Design loads for buildings.
Steel construction, stability cases.
Cladding for external walls.
Steel structures, design and dimensioning.
Steel framed structures.
Standard specication for stainless steel bars and shapes.

Standard specication for annealed or cold worked austenitic stainless steel sheets.
Uniform Building Code & International Building Code
Eurocodes
EN 1990 - 1999
The following design factors are considered
Natural Stone Material
Wall Structure :
Dimensions of natural stone slabs :
I = Thickness of insulation
C = Cavity
St = Thickness of stone
K = Projection
Design weight for natural stone

slabs : (ds)
Length
=w
Height
=h
Thickness =st
Travertine
Sandstone
Marble&Limestone
Granite
Structure - edge spacing

Minimum distance from the
corner of the slab to the pin centre
should be 2.5 times the slab
thickness.
The minimum pin centre
distance to the edge of slab at the
surface should be 15mm.
The most secure method is to
arrange the distance of the drilled
pin hole centre from the edge of
the slab at 1/4 the size of the slab.
Applied Loads - (Actions)

The following applied loads are considered;
Dead loads
: Weight of natural stone slabs is determined

Fdw=h(m)xw(m)xst(m)ds(KN/m3)
Fdw is multiplied with 1.35 safety factor.
Wind loads
: The max. speed is; vs.

The value of the dynamic pressure of the wind is
q=k. Vs2
The max. design pressure is; wp=cp.Q
The max. design suction is; ws=cs.Q
ws=0.7.Q (normal)
ws=2.0.Q (edge)
wp & ws are multiplied with 1.50 safety factor
Thermal loading : The following temperature is considered

Range on the stone;
Tmin C < t C < tmax C
The max. thermal loading in the stone is;
t=tmax - tmin
The max. thermal expansion for stone slab is;
l=.t.L
St
Anchor Pins
Anchor pins are inserted into
the drilled holes on the edge
of the slab from four points.
Drilled holes should be
aprox. 3 mm wider than the pin
diameter and minimum 25 mm
in length.
Minimum 2 mm space
should be left between the slab
below and the bottom edge of
the adjustable arm.
A plastic tube is inserted on
the slabs below to absorb wind
loads.
from
24000 N/m3
26000 N/m3
27000 N/m3
28000 N/m3
|6
Design Principles
Wall Backing
Group of Bolts
The anchoring ground can be concrete, brickwork, lled hollow

block or steel structure. Different types of bolts are used for
backing.
The distance between anchor bolts;

A, which is necessary for a full cone
of concrete to break away, is given by
the crater diameter; C, depending on
the type of anchor. This diameter is
1.5 to 2.5 times the depth of
embedment, D.
The type of wall backing is taken into consideration to propose

suitable bolts for xing the anchors.
Application Type
Load Principles
Horizontal Joints
The anchors carry half the weight of the natural stone slabs in
horizontal installation. Anchors bear half the weight of the slab above
and also act as restraint, holding the slabs below and restraining them
against wind pressure and suction.
Vertical (Dead Load) and Horizontal (Wind Load) loads are determined
according to the following diagram. The following principle is applied
before designing a xing system.
Load Bearing & Restraint

Restraint
Support anchor in horizontal joint

Vertical load from dead load
FDW = (st x w x h x ds) / 2 (for each anchor)
Restraint anchor in horizontal joint

FWP = (w x h x qp) / 2 ( for each anchor)
FWS = (w x h x qs) / 2 ( for each anchor)

Min. Projection size 45 mm
Load Bearing
Indirect xing to channels
Min. Projection size 90 mm.
Vertical Joints
The load bearing anchors carry the full weight of the natural stone
slab in vertical installation. Each anchor bears half the weight of the
slab on the right and half the weight of the slab on the left. Restraint
anchors hold the slabs below and restrain them against wind pressure
and suction.
FDW = Dead load

FWP = Wind load at pressure case
FWS = Wind load at suction case
ds = Denstiy of stone
qw = Design wind pressure
qs = Design wind suction
Support anchor in vertical joint

Vertical load from dead load
FDW = (st x w x h x ds) / 1 (for each anchor)
t = Thickness of stone
w = Width of stone
h = Height of stone
Restraint anchor in vertical joint

FWP = (w x h x qp) / 2 ( for each anchor)
FWS = (w x h x qs) / 2 ( for each anchor)

Min. Projection size 45 mm
Load Bearing
& Restraint
Restraint
Indirect xing to channels

Min. Projection size 90 mm.
Material Grade
Anchors, adjustable arms and pins must
be stainless steel grade AISI 304 - 1.4301
(A2) & AISI 316-1.4401 (A4).
Recommended material specications for
xing systems are shown in the following
table.
PRODUCT
Anchors
Channels
Bolts
Hexagon Nuts
Washers
Stainless Steel
AISI = W.-Nr.
304 = 1.4301
316 = 1.4401
316Ti = 1.4571
304
316
= 1.4301
= 1.4401
DIN 933
(A2/50-A2/70)
A4/50-A4/70)
DIN 934 & DIN 439
(A2/50-A2/70)
A4/50-A4/70)
DIN 125
Steel
DIN = W. -Nr.
Not Advisable
Hot dip galv.
Hot dip galv.
St 37-2 = 1.0037
St 44-2 = 1.0044
Electro galv. St 37
Strength class 4.6/8.8
Electro galv. St 37
Strength class 8
ST DIN 125
|7
HZ Z Anchor Fixing Systems - Technical Details

Direct xing into concrete walls with expansion bolts. Indirect xing into sub channel system with hex bolts.
Three dimensional adjustability - Quick and easy xing.
Installation at horizontal and vertical joints.
Recommended projection sizes up to 135 mm & loads up to 800 N.
HZ01
Z Anchor
HZ02
Z Anchor
HZ05 Z Anchor
With riveted nut
HZ07
Soft Anchor
HZ08 Z Anchor
For large projections
HRS1
Restraint Anchor
Three dimensional adjustability

1) Vertical adjustment is
provided by the slotted
hole. The anchor is xed
on to the bolt with the
serrated washer at the
desired level.
2) Adjustment of the
projection size is
provided by rotating the
adjustable arm. The
adjustable arm is locked
with the hexagon nut.
Installation at horizontal joints
3) Adjustment of the
anchor left and right is
provided by sliding the
body up to 15 degrees
side ways.
Installation at vertical joints
Load Bearing &

Restraint
Restraint
Load
Bearing
Suitable for concrete walls. Anchors are xed directly on to concrete walls with expansion bolts.
Recommended projection size between 45 mm to 135 mm and loads up to 800 N.
In horizontal joint installation, slabs are pinned on the bottom and upper sides. Anchors act as load bearing carrying half the weight of the
slabs above. Anchors also act as restraints, holding the slabs below and restraining against wind suction and pressure.
In vertical joint installation slabs are pinned on the left and right sides. Anchors on the bottom are load-bearing anchors carrying the whole
weight of the slab. Half the weight of the slab on the left and half the weight of the slab on the right. Anchors on the top are restraint
anchors holding the slabs and restraining against wind suction and pressure.
Three - dimensional adjustability allows quick and easy installation.
The design and structural calculations of these anchors are made in our technical department. Special design and manufacturing can be
made for the requirements of each project.
|8
HZ Z Anchor Fixing Systems - Installation Detail

Adjustable arm
Variations
Insulation
Load Bearing
& Restraint
Shape A
Wall
Shape C
Anchor set
Shape E
In this instance the dead load of the

slab is divided by two, as half the
weight of the slab is transferred to
the load bearing anchors.
Shape F
Stone slab
1- Through bolt
2- Anchor body
Shape H
Restraint
3- Serrated washer
4- Round washer
Load
Bearing
5- Hex nut for through bolt

6- Hex nut for adjustable arm
Section A-A
Shape J
7- Adjustable arm
8- Plastic tube
9- Flanged pin
Shape K

Elevation view

slab is divided by one, as the whole
Section a-a
Installation details
Restraint
HZ02 Z Anchor
Load Bearing
& Restraint
Load Bearing

Elevation view
Section a-a
Restraint
HZ02 Z Anchor
Load Bearing
HRS01 Z Restraint
Anchor
Load Bearing
& Restraint
|9
HZ01 Z Anchor - Technical Details

Fdw
For anchoring into

concrete C20/25
Cement
groul
K
E.b.
Load
Bearing
Fws/Fwp
Drilled hole may be

required for closely
spaced walls.
EAL
Restraint
Plastic
tube
St=20-50 mm
St
Technical Details
Product
Code
Projection
K (mm)
Min.
Projection
Max.
Projection
K - (mm) K + (mm)
Dead
Load
Forming
Size
WindPressure
WindSuction
Expansion
Bolt Size
Pin
Size
Adj. Arm Adj. Arm Adj. Arm

Metric
Flat
Length
Size
Thickness
Fdw (N)
F (mm)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)
M (mm)
T (mm)
EAL (mm)
HZ01-452
45
40
60
10
HZ01-552
55
50
70
20
HZ01-752
75
60
90
HZ01-952
95
80
110
60
HZ01-553
55
50
70
20
HZ01-753
75
60
90
HZ01-953
95
80
110
HZ01-1153
115
100
130
80
HZ01-554
55
50
70
10
HZ01-754
75
60
90
HZ01-954
95
80
110
HZ01-1154
115
100
130
60
80
HZ01-755
75
60
90
20
80
HZ01-955
95
80
110
40
HZ01-1155
115
100
130
HZ01-1355
135
120
150
200
300
400
500
40
40
60
20
40
60
60
312
219
M8X80
M10
3.5
60
70
70
60
468
328
M8X80
M10
3.5
70
70
70
70
624
780
437
546
M10X90
M10X90
M12
M12
80
4.5
4.5
80
80
80
80
80
Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4).

Table above is prepared according to DIN 18516 standards.
Loads stated are working resistance loads.
Other sizes are available for production upon request.
Bolts are provided separately.
Structural calculation reports are available upon order.
HZ01 Z Anchor
Load bearing & restraint
Projection sizes between 45 and 135 mm
Suitable for horizontal & vertical joints
Fastened on to load bearing walls with expansion bolts and on to channels with set screws
Product code description
Shape A
Shape B
HZ01 - 45 2 A
Shape
Dead Load (x10 Kg)
Projection (mm)
Type
Loads up to 500 N
Stone thicknesses 20-50 mm
Shape C
Shape D
| 10
HZ02 Z Anchor - Technical Details

Fdw
For anchoring into

concrete C20/25
Cement
groul
K
E.b.
Load
Bearing
Fws/Fwp
Drilled hole may be

spaced walls.
EAL
Restraint
Plastic
tube
St=20-50 mm
St
Technical Details
Product
Code
Projection
K (mm)
Min.
Projection
Max.
Projection
K - (mm) K + (mm)

Flat
Metric
Length
Thickness
Size
Dead
Load
Forming
Size
WindPressure
WindSuction
Expansion
Bolt Size
Pin
Size
Fdw (N)
F (mm)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)
M (mm)
T (mm)
EAL (mm)
HZ02-452
45
40
60
10
HZ02-552
55
50
70
20
HZ02-752
75
60
90
HZ02-952
95
80
110
60
HZ02-553
55
50
70
20
HZ02-753
75
60
90
HZ02-953
95
80
110
HZ02-1153
115
100
130
80
HZ02-554
55
45
70
10
HZ02-754
75
60
90
HZ02-954
95
80
110
HZ02-1154
115
100
130
60
80
HZ02-755
75
60
90
20
80
HZ02-955
95
80
110
40
HZ02-1155
115
100
130
HZ02-1355
135
120
150
80
80
HZ02-756
75
60
90
20
80
HZ02-956
95
80
110
40
HZ02-1156
115
100
130
HZ02-1356
135
120
150
80
80
HZ02-758
75
60
90
20
80
HZ02-958
95
80
110
40
HZ02-1158
115
100
130
HZ02-1358
135
120
150
200
300
400
500
600
800
40
40
60
20
40
60
60
60
60
312
219
M8X80
M10
60
3.5
70
70
60
468
328
M8X80
M10
60
3.5
60
60
70
624
780
936
1235
437
546
655
865
M8X80
M8X80
M10X90
M10X90
M12
M12
M14
M14
80
4.5
80
80
4.5
80
80
5.5
80
80
5.5
80
80
80
Material : Stainless Steel 1.4301 (A2) & 1.4401 (A4). Table above is prepared according to DIN 18516 standard. Loads
stated are working resistance loads. Other sizes are available for production upon request. Bolts are provided
separately. Structural calculation reports are available upon order.
HZ02 Z Anchor
Shape A
Shape B
HZ02 - 45 2 A
Shape
Dead Load (x10 Kg)
Projection (mm)
Type
Loads up to 800 N
Shape C
Shape D
| 11
HZ05 Z Anchor - With Riveted Nut - Technical Details

Fdw
For anchoring into

concrete C20/25
Cement
groul
K
E.b.
Load
Bearing
Fws/Fwp
Drilled hole may be

spaced walls.
EAL
Restraint
Plastic
tube
St=20-50 mm
St
Technical Details
Product
Code
Projection
K (mm)
Min.
Projection
Max.
Projection
K - (mm) K + (mm)
Dead
Load
Forming
Size
WindPressure
WindSuction
Expansion
Bolt Size
Pin
Size

Metric
Flat
Length
Size
Thickness
Fdw (N)
F (mm)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)
M (mm)
T (mm)
EAL (mm)
HZ05-452
45
40
60
10
HZ05-552
55
50
70
20
HZ05-752
75
60
90
HZ05-952
95
80
110
60
HZ05-553
55
50
70
20
HZ05-753
75
60
90
HZ05-953
95
80
110
HZ05-1153
115
100
130
80
HZ05-554
55
50
70
10
HZ05-754
75
60
90
HZ05-954
95
80
110
HZ05-1154
115
100
130
60
80
HZ05-755
75
60
90
20
80
HZ05-955
95
80
110
40
HZ05-1155
115
100
130
HZ05-1355
135
120
150
200
300
400
500
40
40
60
20
40
60
60
312
219
M8X80
M10
3.5
60
60
60
60
468
328
M8X80
M10
3.5
60
60
60
70
624
780
437
546
M8X80
M8X80
M12
M12
80
4.5
4.5
70
80
80
80
80
Material : Stainless Steel 1.4301 (A2) & 1.4401 (A4).

Table above is prepared according to DIN 18516 standard.
HZ05 Z Anchor
Shape A
Shape B
HZ05 - 45 2 A
Shape
Dead Load (x10 Kg)
Projection (mm)
Type
Loads up to 500 N
Shape C
Shape D
| 12
HRS1 Restraint Anchor - Technical Details

For anchoring into
concrete C20/25
Cement
Grout
E.b.
Restraint
Fws/Fwp
Plastic
Tube
EAL
St
St=20-50 mm
Available in sizes to t the projection range of all HZ anchors.
Technical Details
Product
Code
Projection
K (mm)
Min.
Projection
Max.
Projection
K - (mm) K + (mm)
Forming
Size
WindPressure
WindSuction
Expansion
Bolt Size
Pin
Size
F (mm)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)

Metric
Flat
Length
Size
Thickness
M (mm)
T (mm)
EAL (mm)
HRS1-55
55
53
70
20
HRS1-75
75
63
90
40
HRS1-95
95
80
110
60
HRS1-115
115
100
130
60
90
HRS1-135
135
115
150
60
110
60
70
312
219
M8X80
M8
70

HRS1 Restraint Anchor

Shape A
Shape B
HRS1 - 45 A
Shape
Projection (K mm)
Type
Loads up to 312 N
Shape C
Shape D
| 13
HZ02-S Z Anchor- Technical Deatils
2 5 mm
Fdw
For anchoring into

concrete C20/25
Cement
Grout
9 mm
K
E.b.
Load
Bearing
LGA TEST REPORT
No : BBW 121 51 21
Date : 15.10.2006
Fws/Fwp
Drilled hole may be

spaced walls.
EAL
Restraint
70
EA L
Plastic
Tube &
Cement Grout
St=20-50 mm
St
Technical Details
Product
Code
Projection
K (mm)
Min.
Projection
Max.
Projection
K - (mm) K + (mm)
Dead
Load
Offset
WindPressure
WindSuction
Bolt
Size
Pin
Diameter
Fdw (N)
F (mm)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)

Metric
Flat
Length
Size
Thickness
M (mm)
T (mm)
EAL (mm)
HZ02-S-33010/10
45
40
60
500
10
45
HZ02-S-33015/10
50
45
65
500
15
50
HZ02-S-33020/10
55
50
70
500
20
50
HZ02-S-33025/10
60
50
75
400
25
50
HZ02-S-33030/10
65
55
80
400
30
HZ02-S-33040/10
75
60
90
400
40
HZ02-S-33050/10
85
70
100
400
50
HZ02-S-33060/10
95
80
110
300
60
HZ02-S-33080/10
115
100
130
300
80
HZ02-S-330100/10
135
120
150
300
100
70
HZ02-S-330120/10
155
140
170
250
120
70
HZ02-S-43020/12
75
60
90
500
20
60
HZ02-S-43040/12
95
80
110
500
40
60
HZ02-S-43060/12
115
100
130
400
60
HZ02-S-43080/12
135
120
150
300
80
HZ02-S-430100/12
155
140
170
300
100
80
HZ02-S-430100/13
175
160
190
300
100
80
60
312
219
M10
3.5
60
70
70
M8x80
5x70
70
80
468
328
M12
4.5
80

Table above is prepared according to LGA test results.
Loads stated are characteristic resistance loads.
Max Wind pressure: 350 N
Test results are available upon order.
HZ02-S type Z anchors with

standard sizes. Different
types available according to
desired method of xation.
HZ02-2S Type without

serration and with
plain washer.

HZ02-S - 330 / 10 A
Shape
Adj. arm M size (mm)
Anchor body size (mm)
Anchor type
HZ05-S Type with

riveted nut. Serrated
with serrated
washer.
HZ05-2S Type with

riveted nut. Without
serration and with
plain washer.
Shape A
Shape B
Shape C
Shape D
| 14
HZ Z Anchor - Special Applications Details

HZ07 Soft Anchor
Required for installing soft slabs.
HZ08 Z Anchor - for large projection sizes.

Required for projections over 150 mm.
HZ09 Z Anchor - with wedge washer.

Required where loads are over 800 N where serrated washers
may not be strong enough for no slip feature.
Special Designs
Z Anchors are xed on sub frame to
install cornice lining.
Z Anchors are xed on to special steel

structure for cornice parapet installation.
Z Anchors are xed on to special steel

structure for special area installation.
| 15
AXO Body Anchor Fixing Systems - Introduction

Direct xing in to concrete walls with expansion bolts. Indirect xing on to sub channel systems with hex bolts.
Three dimensional adjustability - Quick and easy xing.
Installation at horizontal and vertical joints. Optimum static performance and low engineering for higher loads and larger projection sizes.
Recommended projection sizes up to 260 mm and loads up to 1300 N.
AXO1
Body Anchor
AXO2
Body Anchor
AXO3
Body Anchor
AXO4
Body Anchor
HRS3
Restraint Anchor
1) Vertical adjustment is provided

through the body space. The anchor is
xed onto the bolt through the wedge
washer and the lock washer at the
desired level.
2) Adjusting the projection size by simply

moving the adjustable arm without
rotating. The adjustable arm is safely
xed to the anchor body with the lock
nut and hex bolt.
3) Adjusting the anchor left and right is

provided by sliding the body up to 15
degrees left or right.
Load Bearing &

Restraint
Restraint
Load
Bearing
Suitable for concrete walls. Anchors are xed on to concrete walls with expansion bolts.
Projection sizes between 60 and 260 mm and loads up to 1300 N.
In horizontal installation, slabs are pinned on the bottom and upper sides. The anchors act as load bearing, carrying half the weight of the
slabs above. Anchors also act as restraint holding the slabs below and restraining against wind suction
and pressure.
In vertical installation, slabs are pinned at the left and right sides. The anchors on the bottom are load-bearing anchors carrying the whole
weight of the slab. Half the weight of the slab on the left and half the weight of the slab on the right. The anchors on the top are restraint
anchors holding the slabs and restraining against wind suction and pressure.
Three dimensional adjustability allows quick and easy installation.
The design and structural calculations of these anchors are made in our technical department. Special design and manufacturing can be
made for the requirements of the project.
| 16
AXO Body Anchor Fixing Systems - Installation Detail

Adjustable arm
Variations
Insulation
Load Bearing
& Restraint
Shape A
Wall
Shape C
Anchor set
Shape E

Shape F
Stone slab
1- Through bolt
2- Wedge washer
3- Anchor body
Shape H
4- Lock washer
Restraint
5- Round washer for through bolt

Load
Bearing
7- Locking plate
Section A-A
Shape J
8- Hex bolt
9- Adjustable arm
10- Plastic tube
11- Flanged pin
Shape K

Elevation view

Section a-a
Restraint
AXO4
Body Anchor
Load Bearing
& Restraint
Load Bearing

Elevation view
Section a-a
Restraint

Load Bearing
AXO4
Body Anchor
Load Bearing
& Restraint
| 17
BA Body Anchor - Technical Details

Fdw
For anchoring into
concrete C20/25
K
Cement
groul
E.b.
Load
Bearing
LGA TEST REPORT

No : BBW 0541135-01
Date : 09.05.2005
Fws/Fwp
Body 1607
Body 1207
Restraint
Body 858
EAL
Body 609
Plastic
tube
St
St=20-50 mm
Fdw
For anchoring into
concrete C20/25
K
Cement
groul
E.b.
Load
Bearing
x
Fws/Fwp
Restraint
EAL
Plastic
tube
St
St=20-50 mm
Optimum static performance & low engineering feature
Technical Details
Product
Code
Projection
K (mm)
Min.
Projection
Max.
Projection
Dead
Load
K - (mm) K + (mm) Fdw (N)
Forming WindWind- Expansion

Size
Pressure Suction Bolt Size
F (mm)
Fwp (N)
BA-609
BODY 1
60
50
75
900
28
1100
Fws (N) E.b. (mm)

770
BA-858
BODY 2
85
70
100
800
46
700
700
BA-1207
BODY 3
120
95
135
700
75
650
650
BA-1607
BODY 4
160
145
175
700
115
600
600
Pin
Size
(mm)

Metric
Flat
Length
Size
Thickness
M (mm)
X
Size
T (mm) EAL (mm) x (mm)

60
M8X80
M12
4.5
75
85
50
85

BA Body Anchor
Shape A
Shape B
BA - 60 9 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
Loads up to 900 N
Shape C
Shape D
| 18
AXO1 & AXO2 Body Anchor - Technical Details

Fdw
For anchoring into
concrete C20/25
K
Cement
groul
E.b.
AX01
Body Anchor
Load
Bearing
AX02
Body Anchor
Fws/Fwp
Restraint
EAL
Plastic
tube
St
St=20-50 mm
Fdw
For anchoring into
concrete C20/25
K
Cement
groul
E.b.
Load
Bearing
x
Fws/Fwp
Restraint
EAL
Plastic
tube
St
St=20-50 mm
Optimum static performance & low engineering.
Technical Details
Product
Code
Projection
K (mm)
Min.
Projection
Max.
Projection
Dead
Load

Size
F (mm)
Fwp (N)
AXO1-705
70
55
85
AXO1-1105
110
95
125
AXO1-7013
70
55
85
AXO1-11013
110
95
125
AXO2-1505
150
135
165
500
100
780
AXO2-15013
150
135
165
1300
100
2028
500
1300
20
60
20
60
Fws (N) E.b. (mm)
Pin
Size

Metric
Flat
Length
Size
Thickness
(mm)
M (mm)
X
Size
780
546
M8X80
M12
4.5
85
50
2028
1419
M10X90
M16
85
50
546
M8X80
M12
4.5
85
50
1419
M10X90
M16
Material : Stainless Steel 1.4301 (A2) & 1.4401 (A4). Table above is prepared according to DIN 18516 standard. Loads
stated are working resistance loads. Other sizes are available for production upon request. Bolts are provided
separately. Structural calculations are available upon order.
AXO1 & AXO2 Body Anchor

Shape A
Shape B
AXO1 - 60 9 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
Loads up to 1300 N
Shape C
Shape D
| 19
AXO3 Body Anchor - Technical Details

Fdw
For anchoring into

concrete C20/25
K
Cement
Grout
E.b.
Load
Bearing
x
Fws/Fwp
Restraint
EAL
Plastic
Tube &
F
St
St=20-50 mm
Technical Details
Product
Code
Projection
K (mm)
Min.
Projection
Max.
Projection
Dead
Load

Size
F (mm)
AXO3-2005
200
180
220
AXO3-2205
220
200
240
AXO3-2405
240
220
260
AXO3-2605
260
240
280
215
AXO3-2009
200
180
220
155
AXO3-2209
220
200
240
AXO3-2409
240
220
260
AXO3-2609
260
240
280
215
AXO3-20013
200
180
220
155
AXO3-22013
220
200
240
AXO3-24013
240
220
260
260
240
280
AXO3-26013
Fwp (N)
Fws (N) E.b. (mm)
Pin
Size

Metric
Flat
Length
Size
Thickness
(mm)
M (mm)
X
Size
155
500
175
195
780
546
M8X120
M12
4.5
80
75
1430
1000
M10X130
M14
5.5
80
75
2028
1419
M12X145
M16
80
80
175
900
500
195
175
195
215

AXO3 Body Anchor

Shape A
Shape B
AXO3 - 60 9 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
Loads up to 1300 N
Shape C
Shape D
| 20
AXO4 Body Anchor - Technical Details

Fdw
For anchoring into

concrete C20/25
K
Cement
Grout
E.b.
Load
Bearing
x
Fws/Fwp
Restraint
EAL
Plastic
Tube &
F
St
St=20-50 mm
Technical Details
Product
Code
Projection
K (mm)
Min.
Projection
Max.
Projection
Dead
Load

Size
F (mm)
AXO4-1605
160
140
180
115
AXO4-1805
180
160
200
135
AXO4-2005
200
180
220
AXO4-2205
220
200
240
AXO4-2405
240
220
260
195
AXO4-2605
260
240
280
215
AXO4-1609
160
140
180
115
AXO4-1809
180
160
200
AXO4-2009
200
180
220
AXO4-2209
220
200
240
175
AXO4-2409
240
220
260
195
AXO4-2609
260
240
280
215
AXO4-16013
160
140
180
115
AXO4-18013
180
160
200
135
AXO4-20013
200
180
220
AXO4-22013
220
200
240
AXO4-24013
240
220
260
195
AXO4-26013
260
240
280
215
500
155
175
Fwp (N)
Fws (N) E.b. (mm)
Pin
Size

Metric
Flat
Length
Size
Thickness
(mm)
M (mm)
X
Size
780
546
M8X120
M12
4.5
100
75
1430
1000
M10X130
M14
5.5
100
75
2028
1419
M12X145
M16
100
80
135
900
155
155
1300
175

Structural calculations are available upon order.
AXO4 Body Anchor

Shape A
Shape B
AXO4 - 160 5 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
Loads up to 1300 N
Shape C
Shape D
| 21
HRS3 Restraint Anchor - Technical Details

For anchoring into
concrete C20/25
K
Restraint
Cement
Grout
E.b.
x
Fws/Fwp
Plastic
Tube &
EAL
F
St
St=20-50 mm
Available in sizes to t the projection range of all AXO anchors.
Technical Details
Product
Code
Projection
K (mm)
Min.
Projection
Max.
Projection
K - (mm) K + (mm)
HRS03-60
60
40
80
HRS03-80
80
60
100
HRS03-100
100
80
120
HRS03-120
120
100
140
HRS03-140
140
120
160
HRS03-160
160
140
180
HRS03-180
180
160
200
HRS03-200
200
180
220
HRS03-220
220
200
240
HRS03-240
240
220
260
HRS03-260
260
240
280
Forming
Size
WindPressure
WindSuction
Expansion
Bolt Size
Pin
Size
F (mm)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)

Metric
Flat
Length
Size
Thickness
M (mm)
T (mm)
EAL (mm)
X
Size
x (mm)
65
25
85
100
120
32
140
2028
1419
M8X80
M8
160
30
170
190
40
210
220
50
240

Structural calcultion reports are available upon order.

Shape A
Shape B
HRS03 - 60 A
Shape
Projection (Kmm)
Type
Loads up to 2028 N
Shape C
Shape D
| 22
AXO Body Anchor - Special Application Details
Body anchor with welded plate

with two pins. Used for stone
installation with single anchor.
This type used for installation
of reveals with maximum width
of 25 cm.
Body anchor with welded shims

and HB09 execution. With this
type of anchor, stone panels are
supported from the rear surface
using HB09 bolts instead of
from the edges using pins.
Body anchor with welded plate

and riveted nut. A feature of
HZ05 which is chosen for the
ne adjustment of the
projection by spinning or
rotating the riveted nut while
pins are set on the stone.
Special Designs
Body anchors are used for stone
installation around columns.
Body anchors are used to form an oval

column in natural stone.
t 5mm
:
t 5mm
:
Body anchors used for installation of

parapet area.
| 23
HA L Anchor Fixing Systems - Introduction

Direct xing into concrete walls with expansion bolts. Indirect xing onto sub channel system with hex bolts.
Economical & easy xing.
Installation at horizontal joints.
Adjustability provided through adjustable plates and slot pin holes.
HA01 L Anchor
HA02 L Anchor
Double pin
HA03 L Anchor
With Kerf
HA04 L Anchor
With Adjustable plate
HA05 L Anchor
With Adj. Plate
& Welded Tie
Adjustability
1. Vertical adjustment is made through

the slot hole. The anchor is xed on to
the bolt with the serrated washer and
nut.
2. A slot pin hole can be provided to
enable lateral adjustment of the pin.
3. Greater projection sizes can be

achieved by using shims. Shims are
placed at the back of the anchor.
4. An adjustment plate is available in
HA04 & HA05 type L anchors where
adjustment of the projection size can be
made.
Fdw/2
Fdw/2
Load Bearing &

Restraint
HA01 L Anchors
Suitable for concrete walls.
Recommended projection sizes up to 55
mm.
Slabs are pinned at the bottom and
upper sides.
Adjustability for projection size can be
done by inserting shims between the
anchor and the wall.
Anchors act as load bearing and
restraint, carrying the slabs above and
restraining the slabs below.
HA03 L Anchors
Recommended projection sizes up to 55
mm.
Slabs have slits and the kerf parts of
the anchors are inserted in to the slit
edgesof the slabs.
Adjustability for projection size can be
done by inserting shims between the
anchor and the wall.
HA04 L Anchors
Recommended projection sizes up
to180 mm.
Slabs are pinned from the bottom and
upper sides.
Adjustability of the projection size is
enabled with the adjustable plate, which
is xed to the body with hex bolts.
| 24
HA L Anchor Fixing Systems - Installation Detail

A
Insulation
Load Bearing
& Restraint
Wall

Anchor set
Stone slab
1- Through bolt
2- Anchor body
3- Serrated washer
4- Round washer for through bolt
6- Plastic tube
Section A-A
7- Flanged pin
Elevation view
Section A-A
Elevation view
Section A-A
HA01
L Anchor
HA04
L Anchor
| 25
HA01 L Anchor - Technical Details

Fdw
For anchoring into

concrete C20/25
K
Cement Grout
Load Bearing
Fws/Fwp
E.b.
Restraining
Plastic Tube
St
St=20-50 mm
Technical Details
Product
Code
Projection
Dead Load
Wind
Pressure
Wind
Suction
Bolt Size
Pin
Diameter
Anchor
Length
Anchor
Thickness
K (mm)
Fdw (N)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)
L (mm)
T (mm)
HA01-301
30
HA01-351
35
HA01-401
40
HA01-451
45
51
HA01-501
50
56
HA01-551
55
61
HA01-302
30
38
HA01-352
35
HA01-402
40
HA01-452
45
53
HA01-502
50
58
HA01-552
55
63
HA01-303
30
38
HA01-353
35
43
HA01-403
40
HA01-453
45
HA01-503
50
58
HA01-553
55
63
HA01-304
30
38
HA01-354
35
43
HA01-404
40
HA01-454
45
HA01-504
50
58
HA01-554
55
63
36
41
100
156
110
M8X80
43
200
300
400
312
468
624
219
328
437

M8X80
M8X80
M8X80
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
2.5
48
4
3
48
53
48
53


Limited adjustability
Suitable for horizontal
Shape A
HAO1 - 30 1 A
46
Loads up to 400 N
Stone thicknesses above 20 mm
Shape B
Shape C
| 26
HA02 & HA03 L Anchor - Technical Details

Fdw
HA02 L Anchor
Load bearing & restraint.
Projection sizes between 30
and 55 mm.
Loads up to 400 N.
Suitable for horizontal joints.
Stone thicknesses above
20mm.
Fastened on walls with
expansion bolts.
Stone installation is made
with a single anchor on each
side.
For anchoring into

concrete C20/25
K
Cement Grout
T
Load Bearing
E.b.
Fws/Fwp
Restraining
Plastic Tube
Shape A
St
St=20-50 mm
Technical Details
Shape B
Shape C
HAO2 - 30 2 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
Product
Code
Projection
Dead Load
Wind
Pressure
Wind
Suction
Bolt Size
Pin
Diameter
Anchor
Length
Anchor
Thickness
K (mm)
Fdw (N)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)
L (mm)
T (mm)
HA02-302
30
38
HA02-352
35
43
HA02-402
40
HA02-452
45
HA02-502
50
58
HA02-552
55
63
HA02-304
30
38
HA02-354
35
43
HA02-404
40
HA02-454
45
HA02-504
50
58
HA02-554
55
63
200
312
219
M8X80
48
53
48
400
624
437
M8X80
53
Fdw
HA03 L Anchor
and 55 mm.
Loads up to 400 N.
20mm.
expansion bolts.
Installation is made with kerf
system where there are slit
edges in the slabs.
For anchoring into

concrete C20/25
K
Cement Grout
T
Load Bearing
E.b.
Fws/Fwp
Restraining
Plastic Tube
St
Shape A
St=20-50 mm
Technical Details
Shape B
Shape C
HAO3 - 30 2 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
Product
Code
Projection
Dead Load
Wind
Pressure
Wind
Suction
Bolt Size
Pin
Diameter
Anchor
Length
Anchor
Thickness
K (mm)
Fdw (N)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)
L (mm)
T (mm)
HA03-302
30
HA03-352
35
HA03-402
40
32
37
200
312
219
M8X80
12
42
HA03-452
45
HA03-502
50
52
HA03-552
55
57
HA03-304
30
32
HA03-354
35
37
HA03-404
40
HA03-454
45
HA03-504
50
52
HA03-554
55
57
47
4
3
42
400
624
437
M8X80
15
47
| 27
HA04 & HA05 Mortar Anchor - Technical Details

Fdw
HA04 L Anchor
and 180 mm.
Loads up to 800 N.
20mm.
expansion bolts.
Adjustability of the projection
size is provided with the
adjustable plate.
For anchoring into

concrete C20/25
K
Cement Grout
Load Bearing
E.b.
Fws/Fwp
Restraining
Lp
Plastic Tube
St=20-50 mm
St
Shape A
Technical Details
Shape B
Shape C
HAO4 - 100 6 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
Product
Code
Projection
Min.
Projection
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Bolt
Size
Pin
Diameter
Anchor
Length
Adj.
Plate
Length
Adj.
Plate
Thickness
Fdw (N)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)
L (mm)
Lp (mm)
T (mm)
80
80
K (mm)
K - (mm)
K + (mm)
HA04-1006
100
85
115
HA04-1206
120
105
135
HA04-1406
140
125
155
HA04-1606
160
145
175
130
HA04-1806
180
165
195
150
HA04-1008
100
85
115
70
HA04-1208
120
105
135
HA04-1408
140
125
155
HA04-1608
160
145
175
130
HA04-1808
180
165
195
150
70
90
600
936
655
M12X120
110
90
800
HA05 L Anchor
and 280 mm.
Loads up to 800 N.
20mm.
expansion bolts.
Adjustability of the projection
size is provided with the
adjustable plate.
1235
865
M12X120
110
For anchoring into

concrete C20/25
Fdw
Cement Grout
Load Bearing
E.b.
Fws/Fwp
Restraining
Lp
L
Plastic Tube
St=20-50 mm
St
Shape A
Technical Details
Shape B
Product
Code
Shape C
HAO5 - 200 6 A
Shape
Dead Load (x10 Kg)
Projection (K mm)
Type
Projection
Min.
Projection
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Bolt
Size
Pin
Diameter
Anchor
Length
Adj.
Plate
Length
Adj.
Plate
Thickness
Fdw (N)
Fwp (N)
Fws (N)
E.b. (mm)
(mm)
L (mm)
Lp (mm)
T (mm)
80
80
K (mm)
K - (mm)
K + (mm)
HA05-2006
200
185
215
HA05-2206
220
205
235
HA05-2406
240
225
255
HA05-2606
260
245
275
230
HA05-2806
280
265
295
250
HA05-2008
200
185
215
170
HA05-2208
220
205
235
HA05-2408
240
225
255
HA05-2608
260
245
275
230
HA05-2808
280
265
295
250
170
190
600
936
655
M12X120
210
190
800
1235
865
M12X120
210
| 28
HA L Anchors - Special Application Details
L anchor with adjustable plate

combine with a wedge washer
instead of serrated washer. This
is chosen in cases where
vertical loads are too high for
the serrated washer to sustain
the no slip feature.
L anchor is produced with three

holes in order to accommodate
a
special
requirement.
Customized production is made
in any case to full the special
requirement of the stone
application.
HAZ 21 restraint anchor,

designed for the purpose of
installing into insulated walls
more quickly. Insulation is
drilled instead of cut. HAZ 21
anchors are generally used as
restraints and are used for
corbel facade installations.
Special Designs
L anchors are used to install thick
stone slabs around corners.
L anchors are used to support large semi

circular stones to forming a massive
column block.
L anchors used for stone installation

around column with variations in
stone and projection.
| 29
HDM Mortar Anchor Fixing Systems - Introduction

Direct xing to concrete and masonry walls with mortar
Economical & easy xing
Installation at vertical and horizontal joints
Special design for installing heavy loads at large projection sizes
Load Bearing Anchors
BUN
BUG
Restraint Anchors
BTN
BTG
Installation at horizontal joints with BUG anchors
Fdw/2
Fdw/2
MTN
MTG
HN
HG
Installation at vertical joints with BTN & HG anchors
Fdw/1
Fdw/1
Restraint
Load Bearing &

Restraint
Installation at vertical joints with BUN & HG anchors
Load Bearing
Suitable for installing high load natural stone slabs at large

projection sizes on to concreteand masonry walls.
Holes 6mm larger than the anchor width are drilled in the
walls.
The holes are lled with mortar and anchors are set into mortar
bed.
Fdw/1
Fdw/1
In horizontal joint installation, slabs are pinned on the bottom

and upper sides. Anchors act as load bearing carrying half the
weight of the slabs above. Anchors also act as restraint holding
the slabs below and restraining against wind suction and
pressure.
Restraint
Load Bearing
In vertical joint installation, slabs are pinned at theleft and right

sides. Anchors on the bottom are load-bearing anchors carrying
the whole weight ofthe slab. Half the weight of the slab on the
left and half the weight of the slab on the right. Anchors on the
top are restraint anchors holding the slabs and restraining
against wind suction and pressure.
| 30
HDM Mortar Anchor Fixing Systems - Installation Details

A
Fdw/2
Fdw/2
Load Bearing
& Restraint
Insulation
Wall

Anchor set

Fdw/1
Fdw/1
Stone slab
1- Anchor Body
Restraint
2- Plastic Tube
3- Flanged pin
Load
Bearing

Section A-A
Elevation view
Section A-A
Restraint
BUG
Mortar Anchor
Load Bearing
Load Bearing

Elevation view
Section A-A
Restraint
HG
Restraint Anchor
Load Bearing
BUN
Mortar Anchor
Load Bearing & Restraint
| 31
BUN & BUG Mortar Anchor - Technical Details

BUN Mortar Anchor
and 240 mm.
Loads up to 1200 N
Three dimensional adjust
ability.
Suitable for vertical joints.
Stone thicknesses 20-50 mm.
Fastened into concrete
C20/25 and Masonry M12/II.
For mortaring into

concrete C20/25
and Masonry M12/II
Fdw
B
Fws/Fwp
Load Bearing
Cement Grout
St
Shape A
Plastic Tube
St=20-50 mm
(Top View)
Technical Details
Product
Code
Shape B
BUN - 6 22 A
Shape
Projection
Dead Load (x10 Kg)
Type
BUN-622
BUN-624
BUN-816
BUN-818
BUN-820
BUN-822
BUN-824
BUN-1016
BUN-1018
BUN-1020
BUN-1022
BUN-1024
BUN-1216
BUN-1218
BUN-1220
BUN-1222
BUN-1224
Projection
Min.
Projection
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Z
Size
K (mm)
K - (mm)
K + (mm)
Fdw (N)
Fwp (N)
Fws (N)
Z (mm)
220
240
160
180
200
220
240
160
180
200
220
240
160
180
200
220
240
210
230
150
170
190
210
230
150
170
190
210
230
150
170
190
210
230
230
250
170
190
210
230
250
170
190
210
230
250
170
190
210
230
250
BUG Mortar Anchor

and 240 mm.
Loads up to 600 N.
Three dimensional
adjustability.
Embedded
Pin
Bore
Anchor
Length Diameter Diameter Thickness
L1 (mm)
(mm)
B (mm)
T (mm)
34
38
600
393
786
22
80
800
524
1048
22
80
32
4
36
32
1000
655
1310
22
80
1200
818
1636
22
80
36
4
38
Fdw
For mortaring into

concrete C20/25
and Masonry M12/II
Cement Mortar
Load Bearing
B
Fws/Fwp
T
Restraint
Plastic Tube
Shape A
St=20-50 mm
St
Technical Details
Shape B
Product
Code
BUG-616
BUG-618
BUG-620
BUG-622
BUG-624
BUG - 6 22 A
Shape
Projection
Dead Load (x10 Kg)
Type
Projection
Min.
Projection
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Z
Size
Embedded
Pin
Bore
Anchor
K (mm)
K - (mm)
K + (mm)
Fdw (N)
Fwp (N)
Fws (N)
Z (mm)
L1 (mm)
(mm)
160
180
200
220
240
150
180
200
220
240
170
190
210
230
250
600
571
1142
17
80
B (mm)
T (mm)
32

Table below is prepared according to DIN 18516 standard.
34
36
| 32
BTN & BTG Mortar Anchor- Technical Details

BTN Mortar Anchor
and 240 mm.
Loads up to 600 N.
Three dimensional
adjustability.
Fdw
For mortaring into

concrete C20/25
and Masonry M12/II
Fws/Fwp
Cement
Mortar
Restraint
L
Plastic
Tube
St
St=20-50 mm
Shape A
Technical Details
Product
Code
Shape B
BTN-416
BTN-418
BTN-420
BTN-422
BTN-424
BTN-616
BTN-618
BTN-620
Projection
Min.
Projection
Max.
Projection
Dead
Load
Wind
Pressure
K (mm)
K - (mm)
K + (mm)
Fdw (N)
Fwp (N)
160
180
200
220
240
160
180
200
150
170
190
210
230
150
170
190
170
190
210
230
250
170
190
210
400
Wind Embedded
Pin
Bore
Anchor
Suction Length Diameter Diameter Thickness
Fws (N)
260
520
L1 (mm)
80
(mm)
B (mm)
T (mm)
36
38
40
5
5
5
6
6
36
600
393
786
80
39
41
42
BTN - 4 16 A
Shape
Projection
Dead Load (x10 Kg)
Type
BTG Mortar Anchor

and 240 mm.
Loads up to 500 N.
Three dimensional
adjustability.
Fdw
For mortaring into

concrete C20/25
and Masonry M12/II
Cement Mortar
Load Bearing
Fws/Fwp
T
Restraint
Plastic Tube
Shape A
St=20-50 mm
St
Technical Details
Shape B
Product
Code
BTG-316
BTG-318
BTG-320
BTG-322
BTG-324
BTG-516
BTG-518
BTG-520
BTG - 3 16 A
Shape
Projection
Dead Load (x10 Kg)
Type
Projection
Min.
Projection
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Z
Size
K (mm)
K - (mm)
K + (mm)
Fdw (N)
Fwp (N)
Fws (N)
Z (mm)
160
180
200
220
240
160
180
200
150
170
190
210
230
150
170
190
170
190
210
230
250
170
190
210
Embedded
Pin
Bore
Anchor
L1 (mm)
(mm)
B (mm)
T (mm)
30
300
393
786
22
80
32
34
500
655
1309

22
80
36
38
| 33
MTN & MTG Mortar Anchor - Technical Details

Fdw
MTN Mortar Anchor

and 180 mm.
Loads up to 1000 N.
Three dimensional
adjustability.
Fastened into Masonry M12/II
walls with mortar.
For mortaring into

Masonry M12/II
L
T
Fws/Fwp
Cement
Grout
Load bearing
T
(Top View)
Shape A
Plastic
Tube
St
Technical Details
Product
Code
Shape B
MTN-4 8
MTN-414
MTN-418
MTN-6 6
MTN-612
MTN-620
MTN-10 8
MTN-1024
MTN-1018
Projection
Min.
Projection
Max.
Projection
Dead
Load
Wind
Pressure
K (mm)
K - (mm)
K + (mm)
Fdw (N)
Fwp (N)
80
140
180
60
120
200
80
140
180
70
130
170
50
110
190
70
130
170
90
140
180
70
130
210
80
140
190
Wind Embedded
Pin
Bore
Anchor
Suction Length Diameter Diameter Thickness
Fws (N)
L1 (mm)
(mm)
B (mm)
30
34
36
120
400
295
589
600
442
884
100
737
130
120
140
150
140
180
190
1473
T (mm)
5
5
6
6
6
6
6
6
6
34
38
38
40
42

MTN - 4 8 A
Shape
Projection
Dead Load (x10 Kg)
Type
MTG Mortar Anchor

and 200 mm.
Loads up to 800 N.
Three dimensional
adjustability.
Fdw
For mortaring into

Masonry M12/II
Cement Grout
L1
Z
Load Bearing
T
Fws/Fwp

Fastened into Masonry M12/II
walls with mortar.
Restraint
Plastic Tube
Shape A
St
Technical Details
Shape B
MTG - 3 16 A
Shape
Projection
Dead Load (x10 Kg)
Type
Product
Code
MTG-310
MTG-314
MTG-316
MTG-4 8
MTG-412
MTG-420
MTG-6 6
MTG-610
MTG-616
MTG-8 8
MTG-816
MTG-820
Projection
Min.
Projection
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Z
Size
Embedded
Pin
Bore
Anchor
K (mm)
K - (mm)
K + (mm)
Fdw (N)
Fwp (N)
Fws (N)
Z (mm)
L1 (mm)
(mm)
B (mm)
100
140
160
80
120
200
60
100
160
80
160
200
90
130
150
70
110
190
50
90
150
70
150
190
110
150
170
90
130
210
70
110
170
90
170
210
300
442
884
22
120
34
400
589
1179
22
120
600
884
1768
22
800
1179
2357
22
120
120
125
120
140
140
34
36
40
38
38
40
40
44
46
T (mm)
3
4
5
4
4
6
4
5
6
5
8
8
| 34
HN & HG Mortar Anchor - Restraint - Technical Details

L
HN Mortar Anchor&Restraint
Restraint only.
and 240 mm.
Wind loads up to 1000 N.
Three dimensional
adjustability.
C20/25 Masonry M12/II
walls with mortar.
Cement
Grout
Fws/Fwp
T
Restraint
Plastic Tube
Mortaring into
concrete C20/25
and Masonry M12/II
Shape A
St
Technical Details
Product
Code
Shape B
HN-1016
HN-1018
HN-1020
HN-1022
HN-1024
Projection
Min.
Projection
Max.
Projection
Wind
Pressure
Wind
Suction
Embedded
Length
Pin
Diameter
Bore
Diameter
Anchor
Thickness
K (mm)
K - (mm)
K + (mm)
Fwp (N)
Fws (N)
L1 (mm)
(mm)
B (mm)
T (mm)
160
180
200
220
240
150
170
190
210
230
170
190
210
230
250
1000
500
80
21
3
24
26
HN - 10 16 A
Shape
Projection
Dead Load (x10 Kg)
Type
HG Mortar Anchor
Restraint only.
and 240 mm.
Wind loads up to 1000 N.
Three dimensional
adjustability.
C20/25 Masonry M12/II
walls with mortar.
St
Fdw
B
Fws/Fwp
Coment Grout
Restraint
T
Shape A
Plastic Tube
Mortaring into
concrete C20/25
and Masonry M12/II
Technical Details
Shape B
Product
Code
HG-1016
HG-1018
HG-1020
HG-1022
HG-1024
HG - 10 16 A
Shape
Projection
Dead Load (x10 Kg)
Type
Projection
Min.
Projection
Max.
Projection
Wind
Pressure
Wind
Suction
Embedded
Length
Pin
Diameter
Bore
Diameter
Anchor
Thickness
K (mm)
K - (mm)
K + (mm)
Fwp (N)
Fws (N)
L1 (mm)
(mm)
B (mm)
T (mm)
160
180
200
220
240
150
170
190
210
230
170
190
210
230
250
1000
500
80
21

Structural calculations are available upon request.
3
24
26
| 35
HSD Mortar Anchor Fixing Systems - Introduction

Direct xing to concrete and masonry walls with mortar
Economical & easy xing
HSD01 Mortar Anchor
HSD01 Mortar Anchor

W. Plate
Installation at Horizontal joints

with HRD01 Anchor
HSD03 Mortar Anchor

Twisted head
HSD04 Mortar Anchor

W. Plate & Twisted head
Installation at Horizontal joints

with HSD04
Fdw/2 Fdw/2
HRD01
Mortar Anchor
Installation at Vertical joints

with HSD02&03
Fdw/2 Fdw/2
Load Bearing&
Restraint
Fdw/2 Fdw/2
Restraint
Load Bearing&
Restraint
Load Bearing
HRD Mortar Anchor Fixing Systems - Introduction

Fdw
w
HRD01 Mortar Anchor

and 75 mm.
Loads up to 400 N
Three dimensional
adjustability. Suitable for
horizontal joints.
For mortaring into

concrete C20/25
and Masonry M12/II
K
Cement Grout
L1
Load Bearing
Fws/FwpF
Restraining
Plastic Tube
St
St=20-50 mm
Shape A
Technical Details
Shape B
HRD01 - 35 1 A
Shape
Projection
Dead Load (x10 Kg)
Type
Product
Code
HRD01-351
HRD01-451
HRD01-551
HRD01-651
HRD01-751
HRD01-352
HRD01-452
HRD01-552
HRD01-652
HRD01-752
HRD01-354
HRD01-454
HRD01-554
HRD01-654
HRD01-754
Projection
Min.
Projection
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Anchor
Dowel
Pin
Bore
Flat
Length Embedded Diameter Diameter Thickness
Length
K (mm)
K - (mm)
K + (mm)
Fdw (N)
Fwp (N)
Fws (N)
L (mm)
35
45
55
65
75
35
45
55
65
75
35
45
55
65
75
20
30
40
50
60
20
30
40
50
60
20
30
40
50
60
50
60
70
80
90
50
60
70
80
90
50
60
70
80
90
100
156
110
200
312
219
400
624
437
135
145
155
165
175
135
145
155
165
175
135
145
155
165
175
L1 (mm)
(mm)
90
90
90
B (mm)
T (mm)
12
2.5
14
14
16
3.5
18
| 36
HSD Mortar Anchors - Technical Details

HSD01 Mortar Anchor
Technical Details
Product
Code
Projection
Min.
Projection
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Anchor
Dowel
Pin
Bore
Flat
Length
Fdw (N)
Fwp (N)
Fws (N)
L (mm)
K (mm)
K - (mm)
K + (mm)
HSD01-352
HSD01-452
HSD01-552
HSD01-652
HSD01-752
HSD01-354
HSD01-454
HSD01-554
HSD01-654
HSD01-754
HSD01-356
HSD01-456
HSD01-556
HSD01-656
HSD01-756
35
45
55
65
75
35
45
55
65
75
35
45
55
65
75
20
30
40
50
60
20
30
40
50
60
20
30
40
50
60
50
60
70
80
90
50
60
70
80
90
50
60
70
80
90
Product
Code
Projection
Min.
Projection
200
400
312
624
219
437
655
135
145
155
165
175
135
145
155
165
175
135
145
155
165
175
L1 (mm)
(mm)
B (mm)
T (mm)
21
90
2.5
4
24
26
90
28
2.5
30
32
26
4
600
936
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Anchor
Dowel
Pin
Bore
Flat
Length
Fdw (N)
Fwp (N)
Fws (N)
L (mm)
HSD02 Mortar Anchor
90
28
30
32
Technical Details
K (mm)
K - (mm)
K + (mm)
HSD02-352
HSD02-452
HSD02-552
HSD02-652
HSD02-752
HSD02-354
HSD02-454
HSD02-554
HSD02-654
HSD02-754
HSD02-356
HSD02-456
HSD02-556
HSD02-656
HSD02-756
35
45
55
65
75
35
45
55
65
75
35
45
55
65
75
20
30
40
50
60
20
30
40
50
60
20
30
40
50
60
50
60
70
80
90
50
60
70
80
90
50
60
70
80
90
Product
Code
Projection
Min.
Projection
200
400
312
624
219
437
655
135
145
155
165
175
135
145
155
165
175
135
145
155
165
175
L1 (mm)
(mm)
B (mm)
T (mm)
24
100
2.5
4
28
30
100
32
2.5
34
36
30
4
600
936
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Anchor
Dowel
Pin
Bore
Flat
Length
Fdw (N)
Fwp (N)
Fws (N)
L (mm)
HSD03 Mortar Anchor
100
32
34
36
Technical Details
K (mm)
K - (mm)
K + (mm)
HSD03-352
HSD03-452
HSD03-552
HSD03-652
HSD03-752
HSD03-354
HSD03-454
HSD03-554
HSD03-654
HSD03-754
HSD03-356
HSD03-456
HSD03-556
HSD03-656
HSD03-756
35
45
55
65
75
35
45
55
65
75
35
45
55
65
75
20
30
40
50
60
20
30
40
50
60
20
30
40
50
60
50
60
70
80
90
50
60
70
80
90
50
60
70
80
90
Product
Code
Projection
Min.
Projection
K (mm)
35
45
55
65
75
35
45
55
65
75
35
45
55
65
75
200
312
219
400
624
437
655
135
145
155
165
175
135
145
155
165
175
135
145
155
165
175
L1 (mm)
(mm)
B (mm)
T (mm)
90
26
90
24
26
34
600
936
Max.
Projection
Dead
Load
Wind
Pressure
Wind
Suction
Anchor
Dowel
Pin
Bore
Flat
Length
K - (mm)
K + (mm)
Fdw (N)
Fwp (N)
Fws (N)
L (mm)
20
30
40
50
60
20
30
40
50
60
20
30
40
50
60
50
60
70
80
90
50
60
70
80
90
50
60
70
80
90
HSD04 Mortar Anchor
90
Technical Details
HSD04-352
HSD04-452
HSD04-552
HSD04-652
HSD04-752
HSD04-354
HSD04-454
HSD04-554
HSD04-654
HSD04-754
HSD04-356
HSD04-456
HSD04-556
HSD04-656
HSD04-756
200
312
219
400
624
437
600
936
655
135
145
155
165
175
135
145
155
165
175
135
145
155
165
175
L1 (mm)
(mm)
B (mm)
T (mm)
100
30
100
28
30
100
38
| 37
HMP Sub Channel Fixing Systems - Introduction

Indirect xing on to non-load bearing walls or for large projection sizes
Lower drilling points enable fast installation
Special design is made for sub channel systems to suit various application requirements.
HMPA
HMPB
HMPC
HMPL
HCSP1
HCSP2
HCSP3
HCSP4
HCRS1
HCRS2
HCRS3
HCRS4
HMPA-HC2 Channel System
HMPA-HC2
HMPC-HC1
HMPA-HC3
HMPC-HC1 Channel System

A: Channel support
brackets are xed to
the upper concrete
beams
with
expansion
bolts.
Channels
are
supported
onto
channel
support
brackets with hex
bolts. The levelling of
the wall tolerances is
made by adjusting
the channel through
the support bracket.
B: Channel restraint
brackets are xed to
masonry wall with
chemical
bolts.
Channels are xed to
the
channel
restraints
with
contra nuts. This
prevents
the
channels
from
deecting.
C:Installation
of
stone slabs is done
with the Z Anchors
which are xed onto
the channels with
hex screws and nuts.
D: Channel restraint
brackets are xed to
the lower concrete
beams. Channels
end is xed to the
bracket with contra
nuts.
A: Channel support
brackets are xed to
the concrete beams
with expansion bolts.
Channels
are
supported
onto
channel
support
brackets with hex
bolts.
Channel
supports are not
adjustable in the
horizontal
axis,
therefore the leveling
of the wall tolerances
is made by adjusting
the Z anchors.
B: Channel restraint
brackets are xed to
concrete wall with
expansion
bolts.
Channels are xed to
the
channel
restraints with hex
bolts. This prevents
the channels from
deecting.
C: Installation of
stone slabs is done
with the Z Anchors
which are xed onto
the channels with
hex screws, bolt and
lock nuts.
| 38
HMP Sub Channel Systems - Installation Details

Installation at vertical Joints
Sub
channel
systems are xed to
load bearing beams
for support.
Anchor Set
Stone Slab
Section A-A
Installation at vertical Joints
HCSP2 Channel Support
HCRS2 Channel Restraint
HMPA U Channel
HZ02 Z Anchor
Installation at horizontal Joints
HMPB C Channel
HZ02 Z Anchor
Fdw/1
Channels are xed

on to beams with
channel supports.
Insulation
Wall
Fdw/1
1- Through Bolt
2- Channel Support
3- Plain Washer
4- Washer
5- Nut
6- Bolt Set
7- Channel Restraint
8- Channel
9- Anchor Body
10-Serrated Washer
11-Adjustable Arm
12-Plastic Tube
13- Flanged Pin
Fixing of channels in
the middle to the wall
with
channel
restraints are made to
reduce deection.
When installation is
at vertical joints, the
sub channel system
bears the whole load
of the slabs installed.
When installation is
at horizontal joints,
the sub channel
system bears half the
load of the slabs
installed.
Installation at horizontal Joints

Fdw/1
Fdw/1
| 39
ATS Sub Channel Systems - Introduction

ATS Channel System Elements
HMPS 41/22 & HMPS 41/41

Toothed Channel
ATS-A
Channel Support
ATS-B
Channel Restraint
ATS Fixing System Elements

The ATS Channel system allows the quick and easy
installation of natural stone facades through its
adjustable capability and uncomplicated assembly
features.
The channel system is supported by the ATS-A channel
support brackets.
ATS-B channel restraint brackets, restrain the channel
system against wind pressure and helps prevent the
channel from buckling.
ATS-HZ
Z Anchor
ATS-HA
Special Anchor
ATS-TS
Special Anchor
The HMPS toothed channel enables the xing of the

anchors with hex bolts and lock nuts without the need
for drilled holes and the use of nuts and washers.
Toothed channel and lock nuts provide vertical load
support after xing.
ATS-A Channel Support
ATS-B Channel Restraint
ATS-HZ Z Anchor
| 40
HMP Channels - Technical Details

HMPA U Channel
Technical Details
Product
Code
HMPA-2.5-40/30
HMPA-2.5-40/40
HMPA-3-35/35
HMPA-3-40/30
HMPA-3-40/40
HMPA-3-50/50
HMPA-4-40/40
HMPA-4-50/50
HMPA-5-50/50
Dimensions
X-X Axis
Thickness
T (mm)
Width
W (mm)
Height
H (mm)
2.50
2.50
3.00
3.00
3.00
3.00
4.00
4.00
5.00
40.00
40.00
35.00
40.00
40.00
50.00
40.00
50.00
50.00
30.00
40.00
35.00
30.00
40.00
50.00
40.00
50.00
50.00
IXX
(cm4)
Y-Y Axis
X (mm)
0.74
1.50
1.24
0.85
1.74
2.97
2.19
3.81
4.57
1.57
3.91
2.83
1.79
4.55
9.68
5.67
12.33
14.68
HMPB C Channel
ZX
(cm3)
20.00
20.00
17.50
20.00
20.00
25.00
20.00
25.00
25.00
IYY
(cm4)
4.21
5.97
4.27
4.86
6.92
15.04
8.60
18.97
22.40
ZY (cm3)
Y (mm)
2.11
2.99
2.44
2.43
3.46
6.01
4.30
7.60
8.97
8.80
13.84
12.14
8.83
13.93
17.42
14.10
17.65
17.87
Technical Details
Product
Code
HMPB-2.5-28/15
HMPB-3-38/17
HMPB-2.5-41/21
HMPB-3-41/21
Dimensions
X-X Axis
Thickness
T (mm)
Width
W (mm)
Height
H (mm)
2.50
3.00
2.50
3.00
28.00
38.00
41.00
41.00
15.00
17.00
21.00
21.00
IXX
(cm4)
0.33
0.76
1.32
1.48
HMPC C Channel
ZX
(cm3)
Y-Y Axis
X (mm)
0.43
0.82
1.19
1.33
14.00
19.00
20.50
20.50
IYY
(cm4)
1.43
4.59
5.71
6.55
ZY (cm3)
Y (mm)
1.02
2.42
2.79
3.19
7.38
7.79
9.85
9.86
Technical Details
Product
Code
HMPC-2.5-41/22
HMPC-2.5-41/41
HMPC-3-41/22
HMPC-3-41/41
Dimensions
X-X Axis
Thickness
T (mm)
Width
W (mm)
Height
H (mm)
IXX (cm4)
ZX (cm3)
2.50
2.50
3.00
3.00
41.00
41.00
41.00
41.00
22.00
41.00
22.00
41.00
1.25
7.92
1.69
9.40
0.99
3.62
1.43
4.20
HMPL L Channel
Y-Y Axis
X (mm)
20.50
20.50
20.50
20.50
IYY (cm4)
ZY (cm3)
Y (mm)
5.60
9.40
6.94
11.30
2.72
4.58
3.40
5.50
8.16
19.02
9.16
18.80
Technical Details
Product
Code
HMPL-2.5-30/30
HMPL-2.5-30/40
HMPL-3-30/30
HMPL-3-40/40
HMPL-3-50/50
HMPL-4-40/40
HMPL-50/50
HMPL-5-50/50
Dimensions
X-X Axis
Y-Y Axis
Thickness
T (mm)
Width
W (mm)
Height
H (mm)
IXX (cm4)
ZX (cm3)
X (mm)
IYY (cm4)
ZY (cm3)
Y (mm)
2.50
2.50
3.00
3.00
3.00
4.00
4.00
5.00
30.00
30.00
30.00
40.00
50.00
40.00
50.00
50.00
30.00
40.00
30.00
40.00
50.00
40.00
50.00
50.00
0.93
1.04
1.09
2.88
6.04
3.72
7.85
9.57
0.44
0.39
0.52
1.02
1.69
1.34
2.22
2.73
21.22
26.33
20.79
28.16
35.72
27.79
35.40
35.03
0.93
2.16
1.09
2.88
6.04
3.72
7.85
9.57
0.44
0.39
0.52
1.02
1.69
1.34
2.22
2.73
8.78
7.23
9.21
11.84
14.28
12.21
14.60
14.97
Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4) and Hot dip galvanized mild steel.
Table below is prepared according to values with 11 drilled holes.
Channels can be provided up to 6 metres length.
| 41
HCSP Channel Supports - Technical Details

Technical Details
Product
Code
Thickness
Width
Height
Forming
Slot Hole
Dia.
Slot Hole
Length
Hole
Dia.
T (mm)
W (mm)
H (mm)
F (mm)
S (mm)
SL (mm)
(mm)
4
4
5
5
5
5
6
6
6
40
40
45
45
45
45
45
45
45
80
90
100
100
100
100
100
100
100
50
60
70
80
90
100
110
120
130
11
11
11
11
11
11
11
11
11
30
30
30
30
30
30
30
30
30
11
11
11
11
11
11
11
11
11
HCSP1-50
HCSP1-60
HCSP1-70
HCSP1-80
HCSP1-90
HCSP1-100
HCSP1-110
HCSP1-120
HCSP1-130
Technical Details
Product
Code
HCSP2-40
HCSP2-60
HCSP2-80
HCSP2-100
HCSP2-120
HCSP2-140
Thickness
Width
Height
Forming
Slot Hole
Dia.
Slot Hole
Length
Hole
Dia.
Thr. Rod
Metric Size
T (mm)
W (mm)
H (mm)
F (mm)
S (mm)
SL (mm)
(mm)
MxL (mm)
4
4
4
4
5
5
160
160
160
160
160
160
85
85
85
85
85
85
40
60
80
100
120
140
11
11
11
11
11
11
30
30
30
30
30
30
11
11
11
11
11
11
M10x70
M10X90
M10X110
M10X130
M10X150
M10X170
Technical Details
Product
Code
HCSP3-70
HCSP3-90
HCSP3-110
HCSP3-130
HCSP3-150
Thickness
Width
Height
Forming
Slot Hole
Dia.
Slot Hole
Length
Hole
Dia.
Slot Hole
Length
T (mm)
W (mm)
H (mm)
F (mm)
S (mm)
SL (mm)
(mm)
SL2 (mm)
4
4
5
5
5
120
120
120
120
120
50
50
50
50
50
70
90
110
130
150
11
11
11
11
11
25
25
25
25
25
11
11
11
11
11
30
30
30
30
30
Thickness
Width
Height
Forming
Slot Hole
Dia.
Slot Hole
Length
Hole
Dia.
Thr. Rod
Metric Size
T (mm)
W (mm)
H (mm)
F (mm)
S (mm)
SL (mm)
(mm)
MxL (mm)
2.5
2.5
2.5
3
3
3
47
47
47
48
48
48
200
200
200
200
200
200
95
115
135
155
175
195
11
11
11
11
11
11
45
45
45
45
45
45
11
11
11
11
11
11
30
30
30
30
30
30
Technical Details
Product
Code
HCSP4-95
HCSP4-115
HCSP4-135
HCSP4-155
HCSP4-175
HCSP4-195
Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4) and Hot dip galvanized mild steel.
Table below is prepared according to values with 11 drilled holes.
Channels can be provided up to 6 metres length.
| 42
HCRS Channel Restrain - Technical Details

Technical Details
Product
Code
HCRS1-50
HCRS1-60
HCRS1-70
HCRS1-80
HCRS1-90
HCRS1-100
HCRS1-110
HCRS1-120
HCRS1-130
Thickness
Width
Height
Forming
Slot Hole
Dia.
Slot Hole
Length
Hole
Dia.
T (mm)
W (mm)
H (mm)
F (mm)
S (mm)
SL (mm)
(mm)
2.5
2.5
3
3
3
3
3
3
3
40
40
40
40
40
40
40
40
40
60
60
60
60
60
60
60
60
60
50
60
70
80
90
100
110
120
130
11
11
11
11
11
11
11
11
11
30
30
30
30
30
30
30
30
30
11
11
11
11
11
11
11
11
11
Thickness
Width
Height
Forming
Slot Hole
Dia.
Slot Hole
Length
Thr. Rod
M. Size
T (mm)
W (mm)
H (mm)
F (mm)
S (mm)
SL (mm)
M (mm)
3
3
3
3
3
3
85
85
85
85
85
85
160
160
160
160
160
160
40
60
80
100
120
140
11
11
11
11
11
11
30
30
30
30
30
30
M10x70
M10X90
M10X110
M10X130
M10X150
M10X170
Technical Details
Product
Code
HCRS2-40
HCRS2-60
HCRS2-80
HCRS2-100
HCRS2-120
HCRS2-140
Technical Details
Product
Code
HCRS3-70
HCRS3-90
HCRS3-110
HCRS3-130
HCRS3-150
Thickness
Width
Height
Forming
Slot Hole
Dia.
Slot Hole
Length
Slot Hole
Dia.
Slot Hole
Length
T (mm)
W (mm)
H (mm)
F (mm)
S (mm)
SL (mm)
S 2 (mm)
SL2 (mm)
3
3
3
3
3
40
40
40
40
40
40
40
40
40
40
70
90
110
130
150
9
9
9
9
9
25
25
25
25
25
9
9
9
9
9
25
25
25
25
25
Thickness
Width
Height
Forming
Slot Hole
Dia.
Slot Hole
Length
Slot Hole
Dia.
Slot Hole
Length
T (mm)
W (mm)
H (mm)
F (mm)
S (mm)
SL (mm)
S 2 (mm)
SL2 (mm)
2.5
2.5
2.5
2.5
2.5
2.5
47
47
47
47
47
47
30
30
30
30
30
30
95
115
135
155
175
195
9
9
9
9
9
9
20
20
20
20
20
20
9
9
9
9
9
9
45
45
45
45
45
45
Technical Details
Product
Code
HCRS4-95
HCRS4-115
HCRS4-135
HCRS4-155
HCRS4-175
HCRS4-195
Material: Stainless Steel 1.4301 (A2) & 1.4401 (A4) and hot dip galvanised ST37 mild steel.
Expansion bolts & bolt sets are provided separately.
| 43
HMP Channel Systems - Application Examples

HMPA-HC2
sub
channel
xing
system:
HMPB-HC1
sub
channel
xing
system:
High load bearing

and adjustable sub
channel system.
Easy to assemble
sub channel system.
Fast and easy

xing of stone slabs.
Easy to install with

uncomplicated
elements.
Minimun projection
size is 90 mm and
maximum is 260
mm.
Minimum
projection size is 110
mm and maximum
is 200 mm.
Ideal for heavy

loads and large
projection sizes.
Ideal for restoration of facades.

Anchors are xed
to channels with hex
bolts and hex nuts.
Anchors are xed

to channels with hex
bolts and hex nuts.
HCSP2
Chan. Sup.
HCRS2
Chan. Rest.
HMPA
U Channel
HZ02
Z Anchor
HRS1
Rest. Anchor
HCSP1
Chan Sup.
ATS sub channel

xing system:
HMPC-HC1H sub
channel system:
Adjustable and
easy to use sub
channel system.
Adjustable sub
channel system with
horizontal channels.
Fast and easy

xing of stone slabs.
Quick adjustability
at horizontal axis.
Minimum
mm and maximum
mm.
Minimum
mm and maximum
is 240 mm.
HZ02
Z Anchor
HMPC
C Channel
HZ01
Z Channel
Anchors are xed

to channels with
lock nuts and hex
bolts.
Anchors are xed

to toothed channels
with lock nuts and
hex bolts.
ATS-B
Chan. Rest.
HMPB
Channel
Ideal for staggered

patterned facades.
Ideal for varying

projection sizes and
slab dimensions.
ATS-A
Chan. Sup.
HCRS1
Chan Rest.
HMPS
Toothed Ch.
ATS-HA
ATS-HZ
Special Anc. Z Anchor
HCSP1
Chan. Sup.
HCRS1
HMPC
Chan. Rest. C Channel
HMP Channel Systems - Special Application Details
Channel sub frame is

designed to accommodate
the natural stone angular
installation.
Channel system is supported

onto concrete oor and
ceiling forming a false wall
for stone installation.
Customized panels with

stone slabs supported onto
channel sub frame.
Stone installation around

structural steel column.
Channels are used to form a
sub frame for xing with
adjustable anchors.
Sub frame is formed to

accommodate the facade
movement. Channels provide the means of easy and
fast installation.
| 44
| 45
Fixing Systems for Reconstructed Stone - Introduction

Fixing systems for the installation of high load natural stone or reconstructed stone are available in a variety of types and size ranges.
The actual system proposal will be made according to the technical requirements of the project. The use of these fixing systems is for
high load coping and cornice stones. Load bearing and restraint anchors are used to install the slabs on to different wall backings using
a variety of expansion bolts.
Application Examples
Periscope Anchors
HPC1
HPC2
HPC3
HPC4
Heavy Load Bearing Anchors
HSM
HSMF-C
HAMF
HAMF-K
Restraint Anchors
HAMF-C
HA-RST 1
HAZ-RST 3
HAZ21
| 46
HMP-ALU Sub Channel Systems

Fixing systems with aluminium channels are available for the installation of natural stone, ceramics and fibre cement panels. A variety
of systems are available to accommodate the application requirements . Custom designs are also made for special requirements. Three
dimensional adjustabilty is provided and fast installation is possible due to the light weight of aluminium and the ease of cutting and
drilling on site.
HMP-ALU-P Aluminium Sub Channel system

Aluminium U Channel is supported and
restrained with stainless steel brackets on
to the walls. Stainless steel body 1 anchors
are used for stone installation.
1- Channel Support
2- Aluminium U Channel
3- Body 1 Anchor
4- Channel Restraint
HMP-ALU-U Aluminium Sub Channel system

Aluminium sub channel system
with vertical and horizontal
channels that allow the fixing of
panels from the rear surface
using undercut bolts.
1- Channel Support
2- Vertical T Channel
3- Horizontal slot channel
4- Bracket with undercut
bolt.
| 47
HCA Corner Anchors- Introduction & Technical Details

For xing small slabs on to supported facade slabs.
Used for reveal, column, soft and sill slabs.
Slabs can be assembled in the work shop for faster installation on site.
Special drilling is required on the slabs, details of which are shown at the bottom of the page.
HCA01 Corner Anchor
HCA01 Application
Reveal slabs can be connected to the
supported slabs at columns. In this
instance HCA01 corner anchors are
used as load bearing and HCA02 are
used as restraint.
HCA02 Corner Anchor
HCA03 Corner Anchor
HCA02 Application
Soft slabs can be connected to the
supported slabs at parapets. In this
instance only HCA02 corner
anchors are used as restraint.
HCA03 Application
This anchor is used to fasten two slabs
together at corners. The disk is inserted
at a split edge on the slab. A special bolt
is xed between the anchor and the disk
which rmly connects the slabs together.
Technical Details
Product
Code
HCA01
Reveal Size
Vertical
Load
Wind Load
Adjustable
Arm
Straight
Pin
(mm)
(mm)
M8x45
5x80
Wind Load
Adjustable
Arm
Straight
Pin
(mm)
(mm)
M8x45
5x80
StxWxL cm
(N)
(N)
3(4)x10x45
38(50)
40
3(4)x15x60
76(100)
50
3(4)x20x75
130(170)
60
Reveal Size
Vertical
Load
Technical Details
Product
Code
HCA02
StxWxL cm
(N)
(N)
3(4)x10x45
38(50)
40
3(4)x15x60
76(100)
50
3(4)x20x75
130(170)
60
Special Drilling for HCA01 & HCA02 Corner Anchors

Special drilling is done to the slabs at the upper face and at the back. The drilling must be done
precisely as shown on the illustration. The adjustable arm inserted from the back of the stone
meets the pin which is inserted from the edge surface of the stone.
| 48
HAZ Accessories - Technical Details

HAA Adjustable Arm
Technical Detail
Product
Code
MetricSize
Size
Reveal
Length
M (mm)
HAA-8/50
HAA-8/60
HAA-8/70
HAA-10/50
HAA-10/60
HAA-10/70
HAA-10/80
HAA-12/50
HAA-12/60
HAA-12/70
HAA-12/80
HAA-14/50
HAA-14/60
HAA-14/70
HAA-14/80
HAA-16/50
HAA-16/60
HAA-16/70
HAA-16/80
Type B : With welded pin
L (mm)
50
60
70
50
60
70
80
50
60
70
80
50
60
70
80
50
60
70
80
8
8
8
10
10
10
10
12
12
12
12
14
14
14
14
16
16
16
16
Type C : With welded plate
HFP Flanged Pin
HFP-4/50
HFP-5/60
HFP-5/70
HFP-6/70
Diameter
Length
(mm)
L (mm)
F (mm)
4
5
5
6
50
60
70
70
5
6
6
7
HTP-5/70
HTP-6/75
Diameter
Length
Trace
Height
(mm)
L (mm)
TH (mm)
5
6
70
75
5.2
6.2
HSP Straight Pin
Diameter
Length
(mm)
L (mm)
4
5
5
6
60
60
70
70
HSP-4/60
HSP-5/60
HSP-5/70
HSP-6/70
HUP U Shaped Pin
HUP-4/50
HUP-5/50
HUP-6/50
Height
Width
(mm)
L (mm)
W (mm)
4
5
6
20
25
30
50
50
50
HCP-4/35
HCP-5/40
HCP-6/45
(mm)
St (mm)
A (mm)
3
3
3
3.5
3.5
3.5
3.5
4.5
4.5
4.5
4.5
5.5
5.5
5.5
5.5
6
6
6
6
4
4
4
5
5
5
5
5
5
5
5
6
6
6
6
6
6
6
6
20
25
30
40
50
Diameter
Cap
Diameter
Length
(mm)
C (mm)
L (mm)
4
5
6
6
7
8
35
40
45
12-13
14-16
16-17
22-24
26-29
T
AF
A
Type E : With welded shim
Technical Details
Product
Code
Thickness
Height
Width
Length
T (mm)
H (mm)
W (mm)
L (mm)
HSW-22307
HSW-22309
HSW-263411
HSW-263413
2.5
2.5
3
3
22
22
26
26
30
30
34
34
7
9
11
13
Product
Code
Thickness
Height
Width
Length
T (mm)
H (mm)
W (mm)
L (mm)
2.5
2.5
3
3
22
22
26
26
30
30
34
34
7
9
11
13
Technical Details
HPW-22307
HPW-22309
HPW-263411
HPW-263413
Technical Details
Product
Code
Thickness
Height
Width
Metric
Hole
T (mm)
H (mm)
W (mm)
M (mm)
6
8
9
10
20
20
20
20
34
34
34
34
M6
M8
M10
M12
Technical Details
Product
Code
HSM-4030-7
HSM-4030-9
HSM-4050-11
HSM-4050-13
Thickness
Height
Width
Slot
Hole
T (mm)
H (mm)
W (mm)
x SL
2
2
3
4
40
40
40
40
30
30
50
50
7x20
9x25
11x25
13x30
HPT Plastic Tube
Technical Details
Product
Code
T (mm)
A+6
A+6
A+6
A+8
A+8
A+8
A+8
A+8
A+8
A+8
A+8
A+8
A+8
A+8
A+8
A+8
A+8
A+8
A+8
HSM Shim Plate
Diameter
HCP Capped Pin
AF (mm)
HMLN-6
HMLN-8
HMLN-10
HMLN-12
Technical Details
Product
Code
Distance
between
Edge & Hole
HMLN Lock Nut
Technical Details
Product
Code
Stone
Thickness
HPW Plain Washer
Technical Details
Product
Code
Pin
Diameter
HFP Flanged Pin
Flange
Diameter
HTP Traced Pin
Flattening
Thickness
Type D : With welded plate&pins
Technical Details
Product
Code
Flat length
Size
Technical Details
Product
Code
HPT-4
HPT-5
HPT-6
Inner
Diameter
Outer
Diameter
Length
In. (mm)
Ou. (mm)
L (mm)
4.5
5.5
6.5
6
7
8
30
40
40
Material : Stainless Steel 1.4301 (A2) & 1.4401 (A4). Material for Plastic Tube: Polyacetal.
| 49
HB Expansion Bolts - Technical Details

HB01 Sleeve Bolt
Application
For fastening xtures to
concrete strength class
C20/25 & solid concrete
block walls.
Available in
Stainless Steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316) and
E.galvanized Mild Steel.
Working Resistance (kN)
Technical Detail
Product Code Example

HB01 - 6 / 80
Length
Diameter
Type
Product
Code
HB01-6/80
HB01-8/80
HB01-10/80
HB01-12/100
Bolt Size
Sleeve
Size
Drill Hole
Dia.
Drill
Length
(mm)
(mm)
D (mm)
HT (mm)
M6X80
M8X80
M10X80
M12X100
8x68
10x68
12x68
16x88
8
10
12
16
55
55
55
75
Bolt Size
Drill Hole
Dia.
Drill
Length
Min.
Embedment
Min.
Embedment
Max.
Fixture
Fixture
Hole Dia.
Thickness
E min. (mm) Smax (mm)
45
45
45
65
10
10
10
12
Max
Torque
D1 (mm) Mdmax(Nm)
Bolt
Length
L (mm)
9
11
13
17
7
15
30
45
80
80
80
100
Max
Torque
Bolt
Length
Thread
Length
L (mm)
LG (mm)
80
100
120
90
110
130
110
125
145
25
45
65
25
45
65
25
45
65
Max
Torque
Bolt
Length
Concrete
Blockwork
Wall
C 20/25
Concrete
Wall
Pullout S hear Pullout S hear
1.30
1.80
2.20
2.70
2.40
4.00
4.80
6.10
2.20
3.00
4.10
4.60
3.30
5.20
7.80
8.60
HB03 Through Bolt

Application
block walls.
Available in
Stainless Steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316) and
E.galvanized mild steel.

HB03 - 8 / 80
Length
Diameter
Type
Technical Detail
Product
Code
HB03-8/80
HB03-8/100
HB03-8/120
HB03-10/90
HB03-10/110
HB03-10/130
HB03-12/110
HB03-12/125
HB03-12/145
(mm)
D (mm)
HT (mm)
M8X80
M8X100
M8X120
M10X90
M10X110
M10X130
M12X110
M12X125
M12X145
8
8
8
10
10
10
12
12
12
65
65
65
70
70
70
95
95
95
55
55
55
65
65
65
80
80
80
Bolt Size
Shell
Size
Drill Hole
Dia.
Drill
Length
(mm)
(mm)
D (mm)
HT (mm)
M6X80
M8X80
M10X100
8X48
10X56
12X68
10
12
14
55
60
70
Max.
Fixture
Fixture
Hole Dia.
Thickness
D1 (mm) Mdmax(Nm)
18
38
58
15
35
55
12
32
52
9
9
9
11
11
11
13
13
13
13
13
13
25
25
25
40
40
40
C 20/25 Concrete
Wall
Pullout
S hear
4.11
6.50
6.47
9.70
9.64
12.40
HB05 Shell Bolt

Application
block walls.
Available in
Stainless steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316)
Product
Code
HB05 - 6 / 80
Length
Diameter
Type
Technical Detail
HB05-6/80
HB05-8/80
HB05-10/100
Min.
Embedment
Max.
Fixture
Fixture
Hole Dia.
Thickness
48
56
68
30
21
30
D1 (mm) Mdmax(Nm)
7
9
11
7
15
25
L (mm)
80
80
100
Concrete
Blockwork
Wall
C 20/25
Concrete
Wall
3.50 3.30 4.50 3.30

4.10 6.70 6.50 6.70
5.20 11.00 9.50 11.00
| 50
HB Expansion Bolts - Technical Details

HB06 Drop in Bolt
Application
concrete walls.
Available in
Stainless Steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316) and
E.galvanized mild steel.
Technical Detail

HB06 - 6
M. Size
Type
Product
Code
HB06-6
HB06-8
HB06-10
HB06-12
Bolt Size
Shell
Size
Drill Hole
Dia.
Drill
Length
(mm)
(mm)
D (mm)
HT (mm)
M6X20
M8X30
M10X30
M12X35
8x30
10x40
12x40
14x50
8
10
12
15
32
43
43
54
Drill
Length
Min.
Embedment
Min.
Embedment
Max.
Fixture
Fixture
Hole Dia.
Thickness
30
40
40
50
Max
Torque
D1 (mm) Mdmax(Nm)
10
10
12
14
7
9
11
13
4
8
15
35
Screw in
Depth
Min/Max
Sd (mm)
C 20/25
Concrete
Wall
C 20/30
Concrete
Wall
8/11
10/13
12/16
14/22
1.30
1.80
2.20
2.70
2.40
4.00
2.80
6.10
2.00
3.20
4.35
6.00
1.78
3.30
3.90
6.80
HB07 Anchor Stud

Application
concrete walls.
Available in
Stainless Steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316) and
E.galvanized Mild Steel.
Product
Code
HB03 - 8 / 80
Length
Diameter
Type
Technical Detail
HB07-8/110
HB07-10/130
HB07-12/160
Bolt Size Drill Hole

Dia.
(mm)
D (mm)
HT (mm)
M8X110
M10X130
M12X160
10
12
14
82
92
115
Max.
Fixture
Fixture
Hole Dia.
Thickness
80
90
110
D1 (mm) Mdmax(Nm)
14
21
28
9
11
15
Hollow
Masonry
Wall
Bolt
Length
Max
Torque
C 20/30
Concrete
Wall
L (mm)
10
20
30
110
130
160
0.70
0.75
0.80
0.70 6.33 4.25

0.75 9.95 7.17
0.80 13.92 10.00
HB09 HAZ Super

Application
natural stone
Available in
Stainless Steel EN
1.4301 & 1.4401 (AISI
304 & AISI 316)
Advantages
No use of special and
expensive drilling tools.
No need for expensive
drill bits.
No stone breakage
during xation of bolt.
HB05 - 24 / 30
Length
Size
Type
Technical Detail
Product
Code
HB09-24/30
HB09-48/45
HB09-72/60
Bolt
Size
Stone Drill Hole

Thickness
Dia.
(mm)
St (mm)
D (mm)
M8X30
M8X45
M8X60
20
30
40
12
12
12
Drill
Length
Min.
Max.
Fixture
EmbedFixture
Hole Dia.
ment Thickness
HT (mm) E min. (mm) Smax (mm)
12
22
32
12
22
32
5
5
5
Max
Torque
Bolt
Length
Thread
Length
D1 (mm)
Mdmax(Nm)
L (mm)
(mm)
9
9
9
13
13
13
30
45
60
18
23
28
Hard
Granite
1.40
3.00
Soft
Marble
1.00
2.10
| 51
References
Project
: Conference Palace Hotel - Abu Dhabi
Contractor
: Turner Construction
Installation Area : 160.000 m2
Project
: Al Nahyan Masque - Abu Dhabi
Contractor
: Six Construct International
Project
: Museum of Islamic Arts - Doha
Contractor
: Baytur Construction
Project
: Bibliotheca Alexandria Library - Alexandria
Contractor
: Balfour Beatty and Arab Contractors JV
Project
: Sabanci University - Istanbul
Contractor
: Koray Construction
Project
: Texas Engineering University - Doha
Contractor
: Midmac Contracting
Project
: Is Bank Towers - Istanbul
Contractor
: Tepe Construction
| 52
References
Project : Demir Bank

Location : Istanbul
Project : Yapi Kredi

Location : Istanbul
Project : Admo Apco

Location : Abu Dhabi
Project : Emirates Towers

Location : Dubai
Project : American Embassy

Location : Istanbul
Project : Zorlu Holding

Location : Istanbul
Project : Fairmont Hotel

Location : Dubai

Location : Kingston
Project : Usadba Center

Location : Moscow
Project : Tax Ofce

Location : Moscow
Project : Hilton Hotel

Location : Jeddah
Project : Kingdom Trade

Location : Riyadh
Project : Istek Vakif

Location : Istanbul
Project : Lazurnaya
Location : Sochi
Project : Medinah
Location : Jeddah
Project : Tekfen Tower

Location : Istanbul
Project : Zadgo Gasco


Location : Astana
Project : Gasprom
Location : Moscow
Project : Trade Center


Location : Yerevan
Project : Riverside Hotel

Location : Moscow
Project : Four Seasons Hotel

Location : Cairo
Project : Garanti Bank

Location : Istanbul
Project : Ritz Carlton Hotel

Location : Moscow
Project : The Fund

Project : Mauritius
Location : Mauritius
| 53
Eurocode Concept Design

Partial vs Global Safety
Factors
The new DIN 1045-1:2008-08
standard has created the basis of
abandoning the Global Safety
factors and is leading towards a
common standard design concept
in Europe.
The change from allowable loads to
design resistance loads may cause
confusion when selecting xings.
When mistakes are made the choice
of xings is either 40 % over design
making it uneconomical because
the xings selected are too big or
40 % under design making it unsafe
because the loads applied are 40 %
higher then assumed.
Global safety factors
vs.
Partial safety factors
FU
Fk
F Rd = all. F *
gl
F
M
F = 1.4
F Rd
F Ed
F Ed
F Rd
FEd FRd
all. F
Q
app F all. F
app. F
FFQ
Q
FQ
FG
In order to prevent mistakes the

applied loads and the resistance of
xings must be correctly
determined and compared.
FFG
G
FU
Minimum failure loads
gl
Global safety factor
all.F
Allowable loads
Partial safety factor for actions
app.F
F Rd
Applied loads
Unfactored live load
Design resistance
FG
F Ed
Design effect load
Safety factor for live load
Fk
Characteristics load
Safety factor for dead load
Safety factor for material
Unfactored dead load
Global Safety Factors

With the current Global safety factor concept, the allowable loads ( all. F) are determined for xings. Applied characteristic force loads (app. F)
are compared with the allowable loads. Allowable loads represent the nominal load capacity and is derived from test results which are then
divided by global safety factor ( gl ). The chosen xing is considered safe with the following condition:
Applied loads ( app. F ) Allowable loads ( all. F )
Partial Safety Factors

The design verication according to Euro code 2 for concrete and Euro code 3 for steel is taken into consideration during the design stage. The
applied loads ( app. F ) are factored with partial factors: for permanent actions 1.35 and for variable actions 1.5. The applied design forces
( FEd ) are compared with the Design resistance ( F Rd ). The design resistance is determined by dividing the characteristic resistance of the
xings with the partial material safety factors subsequently for concrete and steel. The chosen xing is considered safe with the following
condition:
Design Effect Load ( F Ed ) Design Resistance ( F Rd)
The new Euro code concept leads to achieving a more constant and reliable safety level by taking into account different inuences of load and
materials.
Design Effect Load ( F Ed ) = F * F ( F G * G + F Q * Q )
Allowable loads vs Design Resistance

In order to design xings according to the new Euro concept the, applied loads must be factored using partial safety factors to determine the
design loads ( F
FEd
Ed ). The design loads must be compared with the design resistance ( FFRd
Rd ) values of the products to be chosen. If the design
resistance values are not available and only allowable loads are available, the new design resistance values must be calculated. The partial
factor for actions here 1.4 is the weighted average of partial load safety factors 1.35 for permanent actions and 1.5 for variable actions. The
global safety factor remains safe with this equation.
Design Resistance ( FFRd
Rd ) = allowable loads ( all. F) * 1.4
Loads stated on this catalog

The loads stated in this catalogue are the allowable loads that are already factored from the characteristic loads. The allowable loads are labelled
as (Fdw) for dead load / (Fwp) for wind pressure / (Fws) for wind suction.
Allow. loads ( all. F) =(Fdw) Dead load / (Fwp) wind pressure / (Fws) wind suction.
| 54
Technical Information Sheet

It is our objective to gather the necessary information about your project to design and propose the most suitable, secure, easy to use and
economic xing system for your requirement.
In order for our technical department to properly respond to your requirement we kindly ask you to ll in the form below.
Note
As a company who applies the most advanced xing technology, HAZ METAL has earned a
reputation as the leaders in xing sytem innovation and is regarded as the one to follow.
HAZ METAL combines the international standards with its production technology to establish
a technical excellence within the industry.
HAZ METAL readily embraces the responsibility of a major producer and shares its expertise
with problem solving solutions.
HAZ METAL
GROUP COMPANIES
HAZ PAZARLAMA & DI TC. A..

Sarkanarya Sok. Ece Apt. No. 8/1
Kozyata Mah. 34742 Kadky
stanbul, TRKYE
Tel : +90 (0) 216 410 72 26
Fax : +90 (0) 216 410 71 41
hazpazarlama@hazgrp.com
HAZ INTERNATIONAL LTD.
154 Great North Road Hateld
Herts. AL9 5JN England
Tel : +44 (0) 1707 - 260 180
Fax : +44 (0) 1707 - 260 190
www.hazuk.co.uk
haz@hazuk.co.uk
HAZ EGYPT LTD

3 Hafez Ramadan St.
Nasr City, Cario, Egypt
Tel : + 2 (0) 226 672 0710
www.hazeg.com
info@hazeg.com
HAZ METAL SANAY VE TCARET A..

ehit Er rac Caddesi No. 10
Akay Sanayi Blgesi 31200 skenderun
Hatay / TRKYE
Tel : +90 (0) 326 626 20 50
Fax : +90 (0) 326 626 20 45
www.hazmetal.com
info@hazmetal.com
HAZ MARBLE INDUSTRY & TRADE LLC
First Gulf Building Comiche Street
2nd Floor, Flat No. 202 P.O. Box 5721
Abu Dhabi, United Arab Emirates
Tel : +90 (0) 2 622 07 00
Fax : +90 (0) 2 622 17 00
hazuae@hazmarbleuae.ae
HAZ MARBLE QATAR WLL
P.O.BOX 31296 C-Ring road
Doha / Qatar
Tel : +974 (0) 4467 26 19
Fax : +974 (0) 4647 47 49
hazqatar@hazqatar.com
Product Catalog HAZ-SF-EN / 03.11
HAZ METAL DEUTSCHLAND GmbH

Leonhard Karl Strasse 29
97877 Wertheim, Germany
Tel : +49 (0) 9342 93590
Fax : +49 (0) 9342 935929
www.hazmetal.de
info@hazmetal.de
HAZ RUS LTD.
Elektrolitniy Proezd, Dom 16,
115230 Moscow, Russian Federation
Tel : + 7 (926) 251 37 85
Fax : + 7 (926) 672 31 84
info@hazrus.ru
www.hazrus.ru
HAZ ASIA PACIFIC PTE LTD
Co. reg. no. 201020887N
Blk 22 Woodlands Link
#01-65 Singapore 738734
Tel: +65 6853 7681
Fax: +65 6572 9582
info@hazapac.com
www.hazapac.com

Haz Metal Do Galt As

Uploaded by

Copyright:

Available Formats

Haz Metal Do Galt As

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Haz Metal Do Galt As

Uploaded by

Copyright:

Available Formats

Natural Stone Fixing Systems

Your Fixing Systems Specialist

Natural stone xing system overview

HZ Z Anchor Fixing System

AXO Body Anchor Fixing Systems

HA L Anchor Fixing Systems

HDM Mortar Anchor Fixing Systems

BUN & BUG technical details

BTN & BTG technical details

MTN & MTG technical details

HN & HG technical details

HSD Mortar Anchor Fixing Systems

HSD anchor technical details

HMP Sub Channel Systems

ATS channel system introduction

HMP channel technical details

HCSP channel restraint technical details

HCRS channel restraint technical details

HMP Sub Channel Systems examples

Special Sub Channel Systems

Heavy Duty Fixing Systems

HB06, HB07 & HB09 technical details

Natural Stone Fixing Systems - Overview

HAZ Metal is located in Iskenderun, in the southern part of Turkey,

To design and produce products that exactly meet the expectations

HAZ Metal started producing fixing systems in 1993. Today, the

Your Fixing Systems Specialist

Natural Stone Fixing Systems - Overview

HAZ Metal provides services in the design of xing systems and

With approximately 10.000 sqm of production halls, HAZ Metal

The companys technical staff consists of experienced engineers who

Throughout the years, production techniques and methods have

Natural Stone Fixing Systems - Overview

Fixing to concrete with bolts.

AXO Body Anchor Fixing

Fixing to concrete with bolts.

Direct xing to concrete

HA L Anchor Fixing System

Fixing to concrete with bolts.

Direct xing to concrete

Indirect xing to load

HSD Mortar Anchor Fixing System

Fixing to masonry with mortar.

HMP Sub Channel System

Your Fixing Systems Specialist

Natural Stone Fixing Systems - Overview

Application examples for bolt anchors

To fasten anchors on to isolated walls, the

Application examples of prole systems

Reference is made to the following standards:

HAZ Metal provides services in the

Our technical department receives the necessary technical

Design and installation of natural stone cladding.

Standard specication for stainless steel bars and shapes.

The following design factors are considered

Natural Stone Material

Dimensions of natural stone slabs :

Design weight for natural stone

Structure - edge spacing

Applied Loads - (Actions)