PSN Series

Specifications
PSN17-5DN
PSN17-5DP
PSN17-5DN2
PSN17-5DP2
PSN17-5DNU
PSN17-5DN2U
PSN17-5DPU
PSN17-5DP2U
PSN17-5DN-F
INDUCTIVE PROXIMITY SENSOR(SQUARE DC 3WIRE)
PSN SERIES
A
L
Model
Thank you very much for selecting Autonics products.

For your safety, please read the following before using.
Caution for your safety

Please observe the cautions that follow;
Warning Serious injury may result if instructions are not followed.

Caution Product may be damaged, or injury may result if instructions are not followed.
The following is an explanation of the symbols used in the operation manual.
Caution:Injury or danger may occur under special conditions.
Caution
1. Do not use this unit in place where flammable, explosive gas, chemical strong alkalis, or acids exist.
It may cause a fire or explosion.
2. Do not impact on this unit.
It may cause malfunction or damage to the product.
3. Please observe the rated specification and do not supply AC power on DC type product.
It may cause serious damage to the product.
Max. 10% of sensing distance
Standard sensing
target
18181(Iron)
25251(Iron)
Setting distance
0 to3.5
0 to 5
Power supply
(Voltage range)
12-24VDC
(10-30VDC)
200
700
10
Blue
0V
100
PSN17-8DN-F
PSN17-8DN
PSN17-8DN-F
PSN17-8DN
(Unit:mm)
Dielectric strength
1,500VAC 50/60 for 1minute
Vibration
1 amplitude at frequency of 10 to 55 in each of X, Y, Z directions for 2 hours
Shock
500(50G) in X, Y, Z directions for 3 times
Indicator
Operation indicator(Red LED)
Ambient
temperature
-25 to 70, Storage: -30 to 80
Ambient
humidity
35 to 95%RH, Storage: 35 to 95%RH

Surge protection circuit, Overload & Short protection circuit, Reverse polarity protection circuit
IP67(IEC standard)
Materials
Case: Heat-resistant ABS, Standard cable(Black): Polyvinyl chloride(PVC).
Approx. 70g
LED
Presence
Nothing
Presence
Nothing
Operation
Return
Operation
Return
(Black-Blue)
H
L
H
L
Indicator
(LED)
ON
OFF
ON
OFF
Normally Open
Normally Closed
Presence
Nothing
Presence
Nothing
Operation
Return
Operation
Return
(Black-Blue)
H
L
H
L
Indicator
(LED)
ON
OFF
ON
OFF
2,000
2,000
PSN40
18
25
30
40
30.8
35.5
48.5
47
3.2
4.2
4.5
5.5
11
18
22
30
18
25.3
30
40
16.8
20
25
35.6
39
53
53
"H" type : 4, 3 cores(Conductor cross section: 0.3, Insulator diameter:1.25)
30
48
30
60
90
120
36
40
40
50
65
70
15
24
15
30
45
60
24
33
25
30
45
45
18
20
20
25
35
35
Target
Target
Moving
direction
Sa Sn
Sensing distance can be changed by the shape, size or material of the target.
Therefore please check the sensing distance as (a), then pass the target within
range of setting distance(Sa) as (b).
Setting distance(Sa)
= Sensing distance(Sn) 70%
Ex)PSN30-10DN
Setting distance(Sa) = 10mm 0.7 = 7mm
Sn:Sensing
{ distance
Sa:Setting distance
(70% of Sn)
(b)
Caution for using

1. This equipment shall not be used outdoors or beyond specified temperature range.
2. Do not apply over tensile strength of cord. (4: max. 30N)
3. Do not use the same conduit with cord of this unit and electric power line or power line.
4. Tighten strength of installing screws should be under 10kgf.cm.(PSN17 Series: max. 5kgf.cm)
5. Please check the voltage changes of power source in order not to excess the rated power input.
6. Do not use this unit during transient time(80ms) after applying power.
7. It might result in damage to this product, if using autotransformer. So please use insulated transformer.
8. Please make wire as short as possible in order to avoid noise.
9. Be sure to use cable as indicated specification on this product. If using wrong cable or bended cable, it shall not have waterproof
properties. 10. It is possible to extend cable with over 0.3mm2 and max. 200m.
11. If the target is plated, the operating distance can be changed by the plating material.
12. It may cause malfunction by metal particle on product.
13. If there are machines(motor, welding, etc.), which occur big surge around this unit, please install the varistor or absorber to source of surge, even though
there is built-in surge absorber in this unit.
14. If connecting the load with big inrush current(DC type bulb) to this unit, the big inrush current will flow because the initial resistance is low. If the current
flows, the resistance of load will be bigger, then it will return to standard current. In this case, proximity sensor might be damaged by inrush current.
If you use DC type bulb, please connect extra relay or current limit resistor in order to protect proximity sensor.
15. If making a transceiver close to proximity sensor or wire connection, it may cause malfunction.
Bracket
PSN17
PSN25
PSN30
2-M3 TAP
2-M4 TAP
3.5
18
2-M4 TAP
3.5
17.5
10
35
34
32
4.75
It may cause malfunction if above instructions are not followed.
PSN40
32
2-M5 TAP
17.8
19.5
15.5
11.8
Major products
2-5.5
Normally Closed
H
E
Normally Open
LED
PSN30
22
Inductive proximity sensor
B
C
40
PSN25
30
Square
(Unit:mm)
PSN17
15
Moving
direction
Approx. 158g
PSN25, PSN30, PSN40
10
PSN40
Setting distance
Approx. 111g
PSN17
PSN30
PSN25
Item
Protection
Approx. 71g
PSN17
Model
Protection circuit
2-4.3
A side length(Unit: mm)
SN
The above specifications are subject to change without notice.
Sensing target
Influence by surrounding metals

When sensors are mounted on metallic panel, it is required to protect the sensors from malfunction by any metallic object. Therefore, be
sure to keep a minimum distance as below chart.
16
Number
Output voltage
Load
200
22
Sensing distance(Unit: mm)
(Black-Blue)
250
14
2
Black
350
Dimensions
Number
Sensing
target
Load
0 to 14
24
+V
0 to 10.5
Main circuit
PNP
Brown
0 to7
Max. 200mA
7.5
0V
0 to 3.5
Within 10 max. of sensing distance at 20 in temperature range of -25 to 70
11
Blue
60601(Iron)
(a)
NPN N.O.(Normally Open)

NPN N.C.(Normally Closed)
PNP N.O.(Normally Open)
PNP N.C.(Normally Closed)
Output voltage
45451(Iron)
1: The response frequency is the average value. The sensing condition is using the standard sensing target. The interval is set as 2 times of the
standard sensing target, and the setting distance is set for 1/2 of the sensing distance.
Environment resistance is rated at no freezing or condensation.
DN
DN2
DP
DP2
(Brown-Black)
30301(Iron)
Control output
18
Black
20
30.5
Standard type
Upper sensing type
Sensing
target
Load
15
Effect by Temp.
8.5
Main circuit
NPN
10
+V
Load
Differential frequency type

When install several proximity sensor closely, it may cause malfunction due to mutual interference. Therefore please use differential frequency as
below picture.
Differential frequency type is only for PSN17.
10
Max. 1.5V
Control output diagram & Load operation

Brown
15
Item
No mark
U
2-4.5
Shape
Standard type
Differential frequency type
12
Sensing distance
Dimension
No mark
F
Parallel
Control output
Face to Face
A
Residual voltage
25
Sensing side
PSN40-20DN
PSN40-20DP
PSN40-20DN2
PSN40-20DP2
Max. 10mA
Unit Weight
Frequency
PSN30-15DN
PSN30-15DP
PSN30-15DN2
PSN30-15DP2
Approval
Ordering information
8 DN U
Hysteresis
Environment
1. In case of using this unit with machinery(Ex: nuclear power control, medical equipment, ship,
vehicle, train, airplane, combustion apparatus, safety device, crime/disaster prevention
equipment, etc) which may cause damages to human life or property, it is required to install
fail-safe device.
It may cause a fire, human injury or damage to property.
17
PSN30-10DN
PSN30-10DP
PSN30-10DN2
PSN30-10DP2
Insulation resistance Min. 50(at 500VDC megger)
Warning
P SN
Sensing distance
Current
consumption
Response
frequency(1)
Please keep these instructions and review them before using this unit.
PSN25-5DN
PSN25-5DP
PSN25-5DN2
PSN25-5DP2
18
PSN17-8DN
PSN17-8DP
PSN17-8DN2
PSN17-8DP2
PSN17-8DNU
PSN17-8DPU
PSN17-8DN2U
PSN17-8DP2U
PSN17-8DN-F
PSN17-8DP-F
PSN17-8DN2-F
PSN17-8DP2-F
PSN17-8DNU-F
PSN17-8DPU-F
PSN17-8DN2U-F
PSN17-8DP2U-F
10
2-3.5
1.2
Mutual-interference & Influence by surrounding metals

Mutual-interference
When several proximity sensors are mounted closely, malfunction of sensor may be caused due to mutual interference. Therefore, be
sure to keep a minimum distance between the two sensors as below chart.
Proximity sensors
Area sensors
Photoelectric sensors
Fiber optic sensors
Door/Door side sensors
Sensor controllers
Graphic/Logic panels
Temperature controllers
Tachometer/Pulse(Rate) meters
Temperature/Humidity transducers
Switching power supplies
Stepping motors/drivers/motion controllers
Field network devices
Laser marking system(CO , Nd:YAG)
Laser welding/soldering system
Counters
Timers
Display units
Panel meters
Pressure sensors
Rotary encoders
Power controllers
http://www.autonics.com
Satisfiable Partner For Factory Automation

HEAD QUARTERS :
41-5. Yongdang-dong, Yangsan-si, Gyeongnam, 626-847,
Korea
OVERSEAS SALES :
Bldg. 402 3rd FL., Bucheon Techno Park, 193, Yakdae-dong,
Wonmi-gu, Bucheon-si, Gyeonggi-do, 420-734, Korea
TEL : 82-32-610-2730 / FAX : 82-32-329-0728
E-mail : sales@autonics.com
The proposal of a product improvement and

development :product@autonics.com
EP-KE-07-0260K

PSN Series

Uploaded by

Copyright:

Available Formats

PSN Series

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PSN Series

Uploaded by

Copyright:

Available Formats

Specifications

INDUCTIVE PROXIMITY SENSOR(SQUARE DC 3WIRE)

Thank you very much for selecting Autonics products.

Caution for your safety

Warning Serious injury may result if instructions are not followed.

Max. 10% of sensing distance

1,500VAC 50/60 for 1minute

1 amplitude at frequency of 10 to 55 in each of X, Y, Z directions for 2 hours

500(50G) in X, Y, Z directions for 3 times

Operation indicator(Red LED)

-25 to 70, Storage: -30 to 80

35 to 95%RH, Storage: 35 to 95%RH

Case: Heat-resistant ABS, Standard cable(Black): Polyvinyl chloride(PVC).

"H" type : 4, 3 cores(Conductor cross section: 0.3, Insulator diameter:1.25)

Caution for using

It may cause malfunction if above instructions are not followed.

Inductive proximity sensor

PSN25, PSN30, PSN40

A side length(Unit: mm)

The above specifications are subject to change without notice.

Influence by surrounding metals

Sensing distance(Unit: mm)

Within 10 max. of sensing distance at 20 in temperature range of -25 to 70

NPN N.O.(Normally Open)

Differential frequency type

Control output diagram & Load operation

Insulation resistance Min. 50(at 500VDC megger)

Mutual-interference & Influence by surrounding metals

Satisfiable Partner For Factory Automation

The proposal of a product improvement and

You might also like