Etsi TS 129 214

ETSI TS 129 214 V12.5.
0 (2014-10)
TECHNICAL SPECIFICATION
Universal Mobile Telecommunications System (UMTS);

LTE;
Policy and charging control over Rx reference point
(3GPP TS 29.214 version 12.5.0 Release 12)
3GPP TS 29.214 version 12.5.0 Release 12
ETSI TS 129 214 V12.5.0 (2014-10)
Reference
RTS/TSGC-0329214vc50
Keywords
LTE,UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N 348 623 562 00017 - NAF 742 C

Association but non lucratif enregistre la
Sous-Prfecture de Grasse (06) N 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
European Telecommunications Standards Institute 2014.
All rights reserved.
TM
TM
TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
ETSI TS 129 214 V12.5.0 (2014-10)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
http://webapp.etsi.org/key/queryform.asp.
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
ETSI TS 129 214 V12.5.0 (2014-10)
Contents
Intellectual Property Rights ................................................................................................................................2
Foreword.............................................................................................................................................................2
Modal verbs terminology....................................................................................................................................2
Foreword.............................................................................................................................................................6
1
Scope ........................................................................................................................................................7
References ................................................................................................................................................7
Definitions and abbreviations ...................................................................................................................8
3.1
3.2
4
4.1
4.2
4.3
4.3.1
4.3.2
4.4
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.5a
4.4.6
4.4.6.1
4.4.6.2
4.4.6.3
4.4.6.4
4.4.6.5
4.4.6.6
4.4.6.7
4.4.6.8
4.4.7
5
5.1
5.2
5.3
5.3.1
5.3.2
5.3.3
5.3.4
5.3.5
5.3.6
5.3.7
5.3.8
5.3.9
5.3.10
5.3.11
5.3.12
5.3.13
5.3.14
5.3.15
5.3.16
Definitions .......................................................................................................................................................... 8
Abbreviations ..................................................................................................................................................... 9
Rx reference point ..................................................................................................................................10

Overview .......................................................................................................................................................... 10
Rx reference model .......................................................................................................................................... 10
Functional elements .......................................................................................................................................... 11
AF ............................................................................................................................................................... 11
PCRF .......................................................................................................................................................... 11
PCC procedures over Rx reference point ......................................................................................................... 12
Initial Provisioning of Session Information ................................................................................................ 12
Modification of Session Information .......................................................................................................... 15
Gate Related Procedures ............................................................................................................................. 16
AF Session Termination ............................................................................................................................. 16
Subscription to Notification of Signalling Path Status ............................................................................... 17
Provisioning of AF Signalling Flow Information ....................................................................................... 18
Traffic Plane Events.................................................................................................................................... 18
IP-CAN Session Termination................................................................................................................ 18
Service Data Flow Deactivation............................................................................................................ 18
Notification of Signalling Path Status ................................................................................................... 19
IP-CAN type change Notification ......................................................................................................... 19
Access Network Charging Information Notification............................................................................. 19
Reporting Usage for Sponsored Data Connectivity .............................................................................. 20
Reporting Access Network Information................................................................................................ 20
Temporary Network Failure handling ................................................................................................... 21
P-CSCF Restoration Enhancement Support ............................................................................................... 21
Rx protocol .............................................................................................................................................22
Protocol support ............................................................................................................................................... 22
Initialization, maintenance and termination of connection and session............................................................ 22
Rx specific AVPs ............................................................................................................................................. 22
Abort-Cause AVP ....................................................................................................................................... 23
Access-Network-Charging-Address AVP .................................................................................................. 24
Access-Network-Charging-Identifier AVP ................................................................................................. 24
Access-Network-Charging-Identifier-Value AVP ...................................................................................... 24
AF-Application-Identifier AVP .................................................................................................................. 24
AF-Charging-Identifier AVP ...................................................................................................................... 25
Codec-Data AVP ........................................................................................................................................ 25
Flow-Description AVP ............................................................................................................................... 25
Flow-Number AVP ..................................................................................................................................... 26
Flows AVP.................................................................................................................................................. 26
Flow-Status AVP ........................................................................................................................................ 26
Flow-Usage AVP ........................................................................................................................................ 27
Specific-Action AVP .................................................................................................................................. 27
Max-Requested-Bandwidth-DL AVP ......................................................................................................... 29
Max-Requested-Bandwidth-UL AVP ......................................................................................................... 30
Media-Component-Description AVP ......................................................................................................... 30
ETSI
5.3.17
5.3.18
5.3.19
5.3.20
5.3.21
5.3.22
5.3.23
5.3.24
5.3.25
5.3.26
5.3.27
5.3.28
5.3.29
5.3.30
5.3.31
5.3.32
5.3.33
5.3.34
5.3.35
5.3.36
5.4
5.4.1
5.5
5.6
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.6.6
5.6.7
5.6.8
ETSI TS 129 214 V12.5.0 (2014-10)
Media-Component-Number AVP ............................................................................................................... 31

Media-Sub-Component AVP ...................................................................................................................... 31
Media-Type AVP ........................................................................................................................................ 31
RR-Bandwidth AVP ................................................................................................................................... 32
RS-Bandwidth AVP .................................................................................................................................... 32
SIP-Forking-Indication AVP ...................................................................................................................... 32
Service-URN AVP ...................................................................................................................................... 32
Acceptable-Service-Info AVP .................................................................................................................... 32
Service-Info-Status-AVP ............................................................................................................................ 33
AF-Signalling-Protocol-AVP ..................................................................................................................... 33
Sponsored-Connectivity-Data AVP ............................................................................................................ 33
Sponsor-Identity AVP................................................................................................................................. 33
Application-Service-Provider-Identity AVP ............................................................................................... 34
MPS-Identifier AVP ................................................................................................................................... 34
Rx-Request-Type AVP ............................................................................................................................... 34
Min-Requested-Bandwidth-DL AVP ......................................................................................................... 34
Min-Requested-Bandwidth-UL AVP ......................................................................................................... 34
Required-Access-Info AVP ........................................................................................................................ 34
IP-Domain-Id AVP ..................................................................................................................................... 35
GCS-Identifier AVP ................................................................................................................................... 35
Rx re-used AVPs .............................................................................................................................................. 35
Use of the Supported-Features AVP on the Rx reference point ................................................................. 37
Rx specific Experimental-Result-Code AVP values ........................................................................................ 38
Rx messages ..................................................................................................................................................... 39
AA-Request (AAR) command .................................................................................................................... 39
AA-Answer (AAA) command .................................................................................................................... 40
Re-Auth-Request (RAR) command ............................................................................................................ 40
Re-Auth-Answer (RAA) command ............................................................................................................ 41
Session-Termination-Request (STR) command ......................................................................................... 41
Session-Termination-Answer (STA) command .......................................................................................... 42
Abort-Session-Request (ASR) command ................................................................................................... 42
Abort-Session-Answer (ASA) command.................................................................................................... 42
Annex A (normative):
IMS Related P-CSCF Procedures over Rx ..................................................44
A.1
Provision of Service Information at P-CSCF .........................................................................................44
A.2
Enabling of IP Flows ..............................................................................................................................45
A.3
Support for SIP forking ..........................................................................................................................46
A.3.1
A.3.2
PCC rule provisioning for early media for forked responses ........................................................................... 46
Updating the provisioned PCC rules at the final answer .................................................................................. 46
A.4
Notification of AF Signalling Transmission Path Status .......................................................................47
A.5
Indication of Emergency Session ...........................................................................................................47
A.6
Notification IP-CAN Type Change ........................................................................................................47
A.7
Support for Early Session disposition SDP ............................................................................................48
A.7.1
A.7.2
A.7.3
A.8
A.9
General ............................................................................................................................................................. 48
Service Information Provisioning for Early Media .......................................................................................... 48
Updating the Provisioned Service Information when Dialogue is established ................................................. 49
Provision of Signalling Flow Information at P-CSCF ...................................................................................... 49
Handling of MPS Session.......................................................................................................................49
A.10 Retrieval of network provided location information ..............................................................................50

A.10.1
A.10.2
A.10.3
A.10.4
A.10.5
General ............................................................................................................................................................. 50
Retrieval of network provided location information at originating P-CSCF for inclusion in SIP Request ...... 50
Retrieval of network provided location information at originating P-CSCF for inclusion in SIP response
confirmation ..................................................................................................................................................... 50
Retrieval of network provided location information at terminating P-CSCF ................................................... 51
Provisioning of network provided location information at SIP session release ............................................... 51
ETSI
Annex B (normative):
B.1
ETSI TS 129 214 V12.5.0 (2014-10)
Flow identifiers: Format definition and examples ......................................53
Format of a flow identifier .....................................................................................................................53
B.1.1
B.1.2
B.1.2.1
B.1.2.2
General ............................................................................................................................................................. 53
Derivation of Flow Identifiers from SDP ......................................................................................................... 54
Standard Procedure ..................................................................................................................................... 54
SDP with 'early session' disposition type .................................................................................................... 54
B.2
Example 1 ...............................................................................................................................................54
B.3
Example 2 ...............................................................................................................................................55
B.4
Example 3 without media components...................................................................................................56
B.5
Example 4 ...............................................................................................................................................57
Annex C (informative):
Void .................................................................................................................59
Annex D (informative):
Change history ...............................................................................................60
History ..............................................................................................................................................................63
ETSI
ETSI TS 129 214 V12.5.0 (2014-10)
Foreword
This Technical Specification has been produced by the 3rd Generation Partnership Project (3GPP).
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
Y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.
ETSI
ETSI TS 129 214 V12.5.0 (2014-10)
Scope
The present document provides the stage 3 specification of the Rx reference point for the present release. The functional
requirements and the stage 2 specifications of the Rx reference point are contained in 3GPP TS 23.203 [2]. The Rx
reference point lies between the Application Function and the Policy and Charging Rule Function.
Whenever it is possible the present document specifies the requirements for the protocol by reference to specifications
produced by the IETF within the scope of Diameter. Where this is not possible, extensions to Diameter are defined
within the present document.
References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
For a specific reference, subsequent revisions do not apply.
For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including
a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same
Release as the present document.
[1]
3GPP TR 21.905: 'Vocabulary for 3GPP Specifications'.
[2]
3GPP TS 23.203: 'Policy and Charging Control architecture'.
[3]
void
[4]
void
[5]
3GPP TS 29.209: 'Policy control over Gq interface', latest Rel-6 version.
[6]
void
[7]
3GPP TS 29.211: 'Rx Interface and Rx/Gx signalling flows', latest Rel-6 version.
[8]
3GPP TS 29.212: 'Policy and Charging Control (PCC); Reference points'.
[9]
3GPP TS 29.213: 'Policy and Charging Control signalling flows and QoS parameter mapping'.
[10]
IETF RFC 3588: 'Diameter Base Protocol'.
[11]
IETF RFC 3556: 'Session Description Protocol (SDP) Bandwidth Modifiers for RTP Control
Protocol (RTCP) Bandwidth'.
[12]
IETF RFC 4005: 'Diameter Network Access Server Application'.
[13]
IETF RFC 4566 : 'SDP : Session Description Protocol''.
[14]
IETF RFC 4006: 'Diameter Credit Control Application'.
[15]
ETSI TS 183 017 v3.2.1: 'Telecommunications and Internet Converged Services and Protocols for
Advanced Networking (TISPAN); Resource and Admission Control: DIAMETER protocol for
session based policy set-up information exchange between the Application Function (AF) and the
Service Policy Decision Function (SPDF); Protocol specification'.
[16]
3GPP TS 23.228: 'IP Multimedia Subsystem (IMS); Stage 2'.
[17]
3GPP TS 24.229: 'IP Multimedia Call Control Protocol based on SIP and SDP; Stage 3'.
ETSI
ETSI TS 129 214 V12.5.0 (2014-10)
[18]
IETF RFC 3264: 'An Offer/Answer Model with the Session Description Protocol (SDP)'.
[19]
Void
[20]
IETF RFC 3162: 'Radius and Ipv6'.
[21]
IETF RFC 5031: 'A Uniform Resource Name (URN) for Emergency and Other Well-Known
Services'.
[22]
Void
[23]
3GPP TS 32.240: 'Telecommunication management; Charging management; Charging architecture

and principles'.
[24]
3GPP TS 32.299: 'Telecommunication management; Charging management; Diameter charging

applications'.
[25]
3GPP TS 29.229: 'Cx and Dx interfaces based on the Diameter protocol; Protocol details'
[26]
3GPP TS 24.292: 'IP Multimedia (IM) Core Network (CN) subsystem Centralized Services (ICS);
Stage 3'.
[27]
IETF RFC 3959 (December 2004): 'The Early Session Disposition Type for the Session Initiation
Protocol (SIP)'.
[28]
3GPP TS 23.380: 'IMS Restoration Procedures'.
[29]
3GPP TS 23.335: 'User Data Convergence (UDC); Technical realization and information flows;
Stage 2'.
[30]
3GPP TS 29.335: 'User Data Convergence (UDC); User Data Repository Access Protocol over the
Ud interface; Stage 3'.
[31]
3GPP TS 22.153: 'Multimedia Priority Service'.
[32]
Void
[33]
3GPP TS 29.274: '3GPP Evolved Packet System. Evolved GPRS Tunnelling Protocol for EPS
(GTPv2)'.
[34]
3GPP TS 29.061: 'Interworking between the Public Land Mobile Network (PLMN) supporting
packet based services and Packet Data Networks (PDN)'.
[35]
IETF draft-ietf-dime-ovli-02: "Diameter Overload Indication Conveyance".
Editor's note: The above document cannot be formally referenced until it is published as an RFC
[36]
3GPP TS 23.468: "Group Services and System Aspects; Group Communication System Enablers
for LTE (GCSE LTE)
Definitions and abbreviations
3.1
Definitions
For the purposes of the present document, the terms and definitions given in 3GPP TR 21.905 [1] and the following
apply:
Application Function (AF): element offering application(s) that use IP bearer resources
NOTE:
One example of an AF is the P-CSCF of the IM CN subsystem.
AF Session: application level session established by an application level signalling protocol offered by the AF that
requires a session set-up with explicit session description before the use of the service.
ETSI
NOTE:
ETSI TS 129 214 V12.5.0 (2014-10)
One example of an application session is an IMS session.
Attribute-Value Pair (AVP): See RFC 3588 [10], corresponds to an Information Element in a Diameter message.
Binding: PCRF process of associating IP flows described in AF Service Information with IP-CAN bearers.
IP-CAN bearer: IP transmission path of defined capacity, delay and bit error rate, etc.
See 3GPP TS 21.905 [1] for the definition of bearer.
IP-CAN session: association between a UE and an IP network (for GPRS, APN).
The association is identified by one UE Ipv4 address and/or one Ipv6 prefix together with a UE identity information, if
available, and a PDN represented by a PDN ID (e.g. an APN). An IP-CAN session incorporates one or more IP-CAN
bearers. Support for multiple IP-CAN bearers per IP-CAN session is IP-CAN specific. An IP-CAN session exists as
long as the related UE Ipv4 address and/or Ipv6 prefix are assigned and announced to the IP network.
IP flow: unidirectional flow of IP packets with the same source IP address and port number and the same destination IP
address and port number and the same transport protocol
Port numbers are only applicable if used by the transport protocol.
MPS session: A session for which priority treatment is applied for allocating and maintaining radio and network
resources to support the Multimedia Priority Service (MPS). MPS is defined in 3GPP TS 22.153 [31].
Packet flow: A specific user data flow carried through the PCEF. A packet flow can be an IP flow.
PCC rule: set of information enabling the detection of a service data flow and providing parameters for policy control
and/or charging control
service information: set of information conveyed from the AF to the PCRF over the Rx interface to be used as a basis
for PCC decisions at the PCRF, including information about the AF session (e.g. application identifier, type of media,
bandwidth, IP address and port number)
service data flow: An aggregate set of packet flows.
3.2
Abbreviations
For the purpose of the present document, the abbreviations given in 3GPP TR 21.905 [1] and the following apply:
ADC
AF
ASP
AVP
CRF
GCS
GCS AS
IP-CAN
MPS
PCC
PCEF
PCRF
PDF
P-CSCF
QoS
SDF
SPR
TDF
UDC
UE
UDR
Application Detection and Control

Application Function
Application Service Provider
Attribute Value Pair
Charging Rules Function
Group Communication Service
Group Communication Service Application Server
IP Connectivity Access Network
Multimedia Priority Service
Policy and Charging Control
Policy and Charging Enforcement Function
Policy and Charging Rule Function
Policy Decision Function
Proxy-Call Session Control Function
Quality of Service
Service Data Flow
Subscriber Profile Repository
Traffic Detection Function
User Data Convergence
User Equipment
User Data Repository
ETSI
Rx reference point
4.1
Overview
10
ETSI TS 129 214 V12.5.0 (2014-10)
The Rx reference point is used to exchange application level session information between the Policy and Charging
Rules Function (PCRF) and the Application Function (AF). As defined in the stage 2 specifications
(3GPP TS 23.203 [2]), this information is part of the input used by the PCRF for the Policy and Charging Control
(PCC) decisions. The PCRF exchanges the PCC rules with the Policy and Charging Enforcement Function (PCEF) and
QoS rules with the Bearer Binding and Event Reporting Function (BBERF) as specified in 3GPP TS 29.212 [8].
Signalling flows related to the both Rx and Gx interfaces are specified in 3GPP TS 29.213 [9].
Refer to Annex G of 3GPP TS 29.213 [9] for Diameter overload control procedures over the Rx interface.
4.2
Rx reference model
The Rx reference point is defined between the PCRF and the AF. The relationships between the different functional
entities involved are depicted in figure 4.1. and 4.2.
Sp
Subscription Profile
Repository
(SPR)
Application
Function
(AF)
Online Charging
System
(OCS)
Rx
Policy and Charging Rules Function

(PCRF)
Sy
Gx
Sd
Gxx
Gy
Bearer
Binding and
Event
Reporting
Function
Policy and
Charging
Enforcement
Function
Gyn
Traffic
Detection
Function
(TDF)
(PCEF)
Gzn
(BBERF)
AN-Gateway
Gateway
Offline
Charging
System
(OFCS)
Gz
Figure 4.1: Rx reference point at the Policy and Charging Control (PCC) architecture with SPR
NOTE 1: The PCEF may support Application Detection and Control feature.
With the UDC-based architecture, as defined in 3GPP TS 23.335 [29] and applied in 3GPP TS 23.203 [2], the UDR
replaces SPR and the Ud reference point provides access to the subscription data in the UDR. The Ud interface as
defined in 3GPP TS 29.335 [30] is the interface between the PCRF and the UDR.The relationships between the
different functional elements are depicted in figure 4.2. When UDC architecture is used, SPR and Sp, whenever
mentioned in this document, are replaced by UDR and Ud.
ETSI
Ud
User Data
Repository
(UDR)
11
ETSI TS 129 214 V12.5.0 (2014-10)
Application
Function
(AF)
Online Charging
System
(OCS)
Rx
Policy and Charging Rules Function

(PCRF)
Sy
Gx
Sd
Gxx
Gy
Bearer
Binding and
Event
Reporting
Function
Policy and
Charging
Enforcement
Function
Gyn
Traffic
Detection
Function
(TDF)
(PCEF)
Gzn
(BBERF)
AN-Gateway
Gateway
Offline
Charging
System
(OFCS)
Gz
Figure 4.2: Rx reference point at the Policy and Charging Control (PCC) architecture with UDR
NOTE 2: The details associated with the Sp reference point are not specified in this Release. The SPR"s relation to
existing subscriber databases is not specified in this Release.
NOTE 3: The UDC Application Informational Model related to the PCRF is not specified in this Release.
NOTE 4: The PCEF may support Application Detection and Control feature.
NOTE 5: PCEF is located in the Gateway node implementing the IP access to the PDN. Refer to Annexes of 3GPP
TS 23.203 [2] for application to specific IP-CAN types.
NOTE 6: Refer to Annexes A.5 and H.2 of 3GPP TS 23.203 [2] for application of AN-Gateways.
4.3
Functional elements
4.3.1
AF
The AF is an element offering applications that require the Policy and Charging Control of traffic plane resources
(e.g. UMTS PS domain/GPRS domain resources). One example of an application function is the P-CSCF. The AF shall
use the Rx reference point to provide session information to the PCRF.
NOTE:
4.3.2
The Afs may be deployed by the same operator offering the IP-CAN or may be provided by external third
party service provider.
PCRF
The PCRF (Policy Control and Charging Rules Function) is a functional element that encompasses policy control
decision and flow based charging control functionalities. These 2 functionalities are the heritage of the release 6 logical
entities PDF and CRF respectively. The PCRF provides network control regarding the service data flow detection,
gating, QoS and flow based charging (except credit management) towards the PCEF. The PCRF receives session and
media related information from the AF and informs AF of traffic plane events.
ETSI
12
ETSI TS 129 214 V12.5.0 (2014-10)
The PCRF may check that the service information provided by the AF is consistent with the operator defined policy
rules before storing the service information. The service information shall be used to derive the QoS for the service. The
PCRF may reject the request received from the AF and as a result the PCRF shall indicate, in the response to the AF,
the service information that can be accepted by the PCRF.
The PCRF may use the subscription information as basis for the policy and charging control decisions. The subscription
information may apply for both session based and non-session based services. The subscription specific information for
each service may contain e.g. max QoS class and max bit rate.
If the AF requests it, the PCRF shall report IP-CAN session events (including bearer events and events on AF signalling
transport) to the AF via the Rx reference point.
The PCRF PCC/QoS Rule decisions may be based on one or more of the following:
-
the session and media related information obtained from the AF via the Rx reference point;
the bearer and subscriber related information obtained from the PCEF over the Gx reference point;
the bearer and subscriber related information obtained from the BBERF over the Gxx reference point;
subscriber and service related data the PCRF may be aware of by configuration or through the Sp reference
point;
pre-configured information in the PCRF.
NOTE:
The details associated with the Sp reference point are not specified in this Release. The SPR"s relation to
existing subscriber databases is not specified in this Release.
The PCRF shall provision PCC/QoS Rules to the PCEF/BBERF via the Gx/Gxx reference point.
4.4
PCC procedures over Rx reference point
4.4.1
Initial Provisioning of Session Information
When a new AF session is being established and media information for this AF session is available at the AF and the
related media require PCC supervision, the AF shall open an Rx Diameter session with the PCRF for the AF session
using an AA-Request command, unless an Rx session has already been established for the AF session (e.g. as per
subclause 4.4.6.7). If an Rx Diameter session already exists for the AF session, the AF uses the existing Rx Diameter
session. The AF shall provide the full IP address of the UE using either Framed-IP-Address AVP or Framed-Ipv6Prefix AVP, and the corresponding Service Information within Media-Component-Description AVP(s). The AF shall
not include circuit-switched bearer related media in the service information sent to the PCRF. The AF shall indicate to
the PCRF as part of the Media-Component-Description whether the media IP flow(s) should be enabled or disabled
with the Flow-Status AVP.
NOTE 1: The AF does not need to open an Rx Diameter session with the PCRF, if the SDP payload is only
proposing to use a circuit-switched bearer (i.e. 'c=' line set to 'PSTN' and an 'm=' line set to 'PSTN', refer
to 3GPP TS 24.292 [26]).
NOTE 2: The Rx Diameter session used for an AF session is different from the Rx Diameter session possibly used
for the notifications of the status of the AF signalling transmission path. A new Rx Diameter session is
established for each new AF session.
The AF may include the AF-Application-Identifier AVP into the AA-Request in order to indicate the particular service
that the AF session belongs to. This AVP can be provided at both AF session level, and Media-Component-Description
level. When provided at both levels, the AF-Application Identifier provided within the Media-Component-Description
AVP will have precedence.
The AF may include the AF-Charging-Identifier AVP into the AA-Request for charging correlation purposes. The AF
may also include the Specific-Action AVP to request notification for certain user plane events, e.g. bearer termination.
The AF may include the Service-URN AVP in order to indicate that the new AF session relates to emergency traffic. If
the PCRF receives the Service-URN AVP indicating an emergency session, the PCRF may apply special policies, for
instance prioritising service flows relating to the new AF session or allowing these service flows free of charge.
ETSI
13
ETSI TS 129 214 V12.5.0 (2014-10)
The AF may include the MPS-Identifier AVP in order to indicate that the new AF session relates to an MPS session. If
the PCRF receives the MPS-Identifier AVP indicating an MPS session, the PCRF may take specific actions on the
corresponding IP-CAN to ensure that the MPS session is prioritized as specified in 3GPP TS 29.212 [8]. For
Multimedia Priority Sevice handling, see Annex A.9.
When the AF is a GCS AS, it may include the GCS-Identifier AVP at command level and Reservation-Priority AVP at
command level or media component level in order to indicate that the new AF session relates to a prioritized Group
Communication session. Based on this information, the PCRF may take specific actions on the corresponding IP-CAN
to ensure that the Group Communication session is prioritized as specified in 3GPP TS 29.212 [8].
If the AF provides service information that has been fully negotiated (e.g. based on the SDP answer), the AF may
include the Service-Info-Status AVP set to FINAL_SERVICE_INFORMATION. In this case the PCRF shall authorize
the session and provision the corresponding PCC/QoS rules to the PCEF/BBERF.
The AF may additionally provide preliminary service information not fully negotiated yet (e.g. based on the SDP offer)
at an earlier stage. To do so, the AF shall include the Service-Info-Status AVP with the value set to PRELIMINARY
SERVICE INFORMATION. Upon receipt of such preliminary service information, the PCRF shall perform an early
authorization check of the service information. For GPRS, the PCRF shall not provision PCC rules towards the PCEF
unsolicitedly. However, the PCRF may authorize a PCC/QoS rule request received from the PCEF/BBERF as per 3GPP
TS 29.212 [8]. Further, if the AF requests the PCRF to report the access network information together with preliminary
service information, the PCRF shall immediately configure the PCEF (or BBERF) to provide the access network
information.
For sponsored data connectivity, the AF shall provide the application service provider identity and the sponsor identity
to the PCRF byincluding the Application-Service-Provider-Identity AVP and the Sponsor-Identity AVP in the
Sponsored-Connectivity-Data AVP in the AA-Request.
NOTE 3: The relationship between the AF and Sponsor is out of scope of this specification. A single AF can serve
multiple ASPs and multiple sponsors, An ASP can also be a sponsor.
To support the usage monitoring of sponsored data connectivity, the AF may also include the Granted-Service-Unit
AVP in the Sponsored-Connectivity-Data AVP and the Specific-Action AVP set to the value USAGE_REPORT in the
AA-Request to request notification when the usage threshold has been reached.
NOTE 4: If the AF is in the user plane, the AF can handle the usage monitoring and therefore it is not required to
provide a usage threshold to the PCRF as part of the sponsored data connectivity information.
If the UE is roaming with the visited access case and the AF is located in the HPLMN or roaming with the home routed
case and operator policies do not allow accessing the sponsored data connectivity with this roaming case, the H-PCRF
shall reject the service request indicating UNAUTHORIZED_SPONSORED_DATA_CONNECTIVITY to the AF.
If the UE is roaming with the visited access case and the AF is located in the VPLMN, the V-PCRF shall reject the
service request indicating UNAUTHORIZED_SPONSORED_DATA_CONNECTIVITY to the AF.
If the UE is in the non-roaming case or roaming with the home routed case and the operator policies allow accessing
the sponsored data connectivity with this roaming case, the following procedures apply:
-
If the PCEF does not support sponsored connectivity and the required reporting level for that service
indicates a sponsored connectivity level according to 3GPP TS 29.212 [8], subclause 4.5.20, then the PCRF
shall reject the request indicating REQUESTED_SERVICE_NOT_AUTHORIZED.
If the PCEF supports sponsored data connectivity feature or the required reporting level is different from
sponsored connectivity level as described in 3GPP TS 29.212[8], then the PCRF, based on operator policies,
shall check whether it is required to validate the sponsored connectivity data. If it is required, it shall perform
the authorizations based on sponsored data connectivity profiles. If the authorization fails, the PCRF
responds to the AF with an AA-Answer including the Experimental-Result-Code AVP set to the value
UNAUTHORIZED_SPONSORED_DATA_CONNECTIVITY. The profile may include a list of Application
Service Providers and their applications per sponsor.
NOTE 5: If the AF is in the operator"s network and is based on the OSA/Parlay-X GW, the PCRF is not required to
verify that a trust relationship exists between the operator and the sponsors.
ETSI
14
ETSI TS 129 214 V12.5.0 (2014-10)
When the PCRF receives an initial AA-Request from the AF, the PCRF shall perform session binding as described in
3GPP TS 29.213 [9]. To allow the PCRF to identify the IP-CAN session for which this request applies, the AF shall
provide either the Framed-IP-Address or the Framed-Ipv6-Prefix containing the full IP address applicable to an IP flow
or IP flows towards the UE. In case of private IP address being used, the AF may provide PDN information if available
in the Called-Station-Id AVP for session binding. The AF may provide the domain identity in the IP-Domain-Id AVP
for session binding.
NOTE 6: The IP-Domain-Id AVP is helpful in the following scenario: Within a PLMN, there are several separate
IP address domains, with PCEF(s) that allocate Ipv4 IP addresses out of the same private address range to
Ues. The same IP address can thus be allocated to Ues served by PCEFs in different address domains. If
one PCRF controls several PCEFs in different IP address domains, the UE IP address is thus not
sufficient for the session binding. An AF can serve Ues in different IP address domains, either by having
direct IP interfaces to those domains, or by having interconnections via NATs in the user plane between
PCEFs and the AF. If a NAT is used, the AF obtains the IP address allocated to the UE via application
level signalling and supplies it for the session binding as Framed-IP-Address to the PCRF. The AF
supplies an IP-Domain-Id value denoting the IP address domain behind the NAT in addition. The AF can
derive the appropriate value from the source address (allocated by the NAT) of incoming user plane
packets.
NOTE 7: When the scenario described in NOTE 6 applies and the AF is a P-CSCF it is assumed that the P-CSCF
has direct IP interfaces to the different IP address domains and that no NAT is located between P-GW and
P-CSCF. How a non-IMS AF obtains the UE private IP address to be provided to the PCRF is out of
scope of the present release; it is unspecified how to support applications that use a protocol that does not
retain the original UE"s private IP address.
If the PCRF fails in executing session binding, the PCRF responds to the AF with an AA-Answer including the
Experimental-Result-Code AVP set to the value IP-CAN_SESSION_NOT_AVAILABLE. Further details on how the
PCRF identifies suitable IP-CAN sessions can be found in the binding mechanism described in 3GPP TS 29.213 [9].
If the request contains Media-Component-Description Attribute-Value Pair(s) (AVP(s)) the PCRF shall store the
received Service Information. The PCRF shall process the received Service Information according to the operator
policy and may decide whether the request is accepted or not. The PCRF may take the priority information within the
Reservation-Priority AVP into account when making this decision. If the service information provided in the AARequest command is rejected (e.g. the subscribed guaranteed bandwidth for a particular user is exceeded), the PCRF
shall indicate in the AA-Answer the cause for the rejection with the Experimental-Result-Code AVP set to the value
REQUESTED_SERVICE_NOT_AUTHORIZED. The PCRF may additionally provide the acceptable bandwidth
within the Acceptable-Service-Info AVP.
To allow the PCRF and PCEF to perform PCC rule authorization and bearer binding for the described service IP flows,
the AF shall supply both source and destination IP addresses and port numbers within the Flow-Description AVP, if
such information is available.
NOTE:
In SDP source port information is usually not available.
The AF may specify the Reservation-Priority AVP at request level in the AA-Request in order to assign a priority to the
AF Session as well as specify the Reservation-Priority AVP at the media-component-description AVP level to assign a
priority to the IP flow. The presence of the Reservation-Priority in both levels does not constitute a conflict as they each
represent different types of priority. Specifically the Reservation-Priority at the AA-Request level provides the relative
priority for a session while the Reservation-Priority at the media-component-description level provides the relative
priority for an IP flow within a session. If the Reservation-Priority AVP is not specified the requested priority is
DEFAULT (0).
The AF may request notifications of specific IP-CAN session events through the usage of the Specific-Action AVP in
the AA-Request command. The PCRF shall make sure to inform the AF of the requested notifications in the event that
they take place.
The AF may include the Rx-Request-Type AVP set to INITIAL_REQUEST in the AAR.
The PCRF shall check whether the received Service Information requires PCC/QoS Rules to be created and provisioned
and/or authorized QoS to be provisioned. Provisioning of PCC/QoS Rules and Authorized QoS to the PCEF/BBERF
shall be carried out as specified at 3GPP TS 29.212 [8].
ETSI
15
ETSI TS 129 214 V12.5.0 (2014-10)
The PCRF shall reply with an AA-Answer to the AF. The acknowledgement towards the AF should take place before or
in parallel with any required PCC Rule provisioning towards the PCEF and shall include the Access-NetworkCharging-Identifier(s) and may include the Access-Network-Charging-Address AVP, if they are available. The AAAnswer message shall also include the IP-CAN-Type AVP, if such information is available. In that case, the AAAnswer message shall also include the RAT-Type AVP when applicable for the specific IP-CAN Type (e.g. 3GPP IPCAN Type). In addition, if IP flow mobility applies to service data flows as specified in 3GPP TS 29.212 [8], such that
a subset of the flows within the AF session are affected, the PCRF shall also include IP-CAN-type and RAT-type
information (if applicable) to IP flow mobility related flows, if such information is available. The IP flow mobility
affected service data flows are included within the Flows AVP at command level. If the PCRF needs to terminate the
Rx session before it has sent the AA Answer, the PCRF shall send the AA Answer immediately and before the AS
Request.
The behaviour when the AF does not receive the AA Answer, or when it arrives after the internal timer waiting for it
has expired, or when it arrives with an indication different than DIAMETER_SUCCESS, are outside the scope of this
specification and based on operator policy.
If the PCRF fails in installing PCC/QoS rules based on the provided service information due to resource allocation
failure as specified in 3GPP TS 29.212 [8] and if requested by the AF, the PCRF shall send an RAR command to the
AF with the Specific-Action AVP set to the value INDICATION_OF_FAILED_RESOURCES_ALLOCATION to
report the resource allocation failure. The AF shall send an RAA command to acknowledge the RAR command
4.4.2
Modification of Session Information
The AF may modify the session information at any time (e.g. due to an AF session modification or internal AF trigger)
by sending an AA-Request command to the PCRF containing the Media-Component-Description AVP(s) with the
updated Service Information. The AF shall send an AA-Request command to the PCRF, only after the previous AARequest has been acknowledged.
If the AF provides service information that has been fully negotiated (e.g. based on the SDP answer), the AF may
include the Service-Info-Status AVP set to FINAL_SERVICE_INFORMATION. In this case the PCRF shall authorize
the session and provision the corresponding PCC rules to the PCEF.
The AF may additionally provide preliminary service information not fully negotiated yet (e.g. based on the SDP offer)
at an earlier stage. To do so, the AF shall include the Service-Info-Status AVP with the value set to PRELIMINARY
SERVICE INFORMATION. Upon receipt of such preliminary service information, the PCRF shall perform an early
authorization check of the service information. For GPRS, the PCRF shall not provision PCC rules towards the PCEF
unsolicitedly. However, the PCRF may authorize a PCC/QoS rule request received from the PCEF/BBERF as per 3GPP
TS 29.212 [8]. Further, if the AF requests the PCRF to report the access network information together with preliminary
service information, the PCRF shall immediately configure the PCEF (or BBERF) to provide the access network
information.
The AF may include the Rx-Request-Type AVP set to UPDATE_REQUEST in the AAR.
The AF may include the MPS-Identifier AVP in order to indicate that the modified AF session relates to an MPS
session. If the PCRF receives the MPS-Identifier AVP, it may take specific actions on the corresponding IP-CAN to
ensure that the MPS session is prioritized as defined in 3GPP TS 29.212 [8]. For Multimedia Priority Sevice handling,
see Annex A.9.
When the AF is a GCS AS, it may include the GCS-Identifier AVP at command level and Reservation-Priority AVP at
command level or media component level in order to modify the priority of an AF session that relates to a prioritized
Group Communication session. Based on this information, the PCRF may take specific actions on the corresponding IPCAN to ensure that the Group Communication session is prioritized as specified in 3GPP TS 29.212 [8].
For sponsored data connectivity, the AF shall provide the application service provider identity and the sponsor identity
to the PCRF by including Application-Service-Provider-Identity AVP and the Sponsor-Identity AVP in the SponsoredConnectivity-Data AVP in the AA-Request.
To support the usage monitoring of sponsored data connectivity, the AF may also include the Granted-Service-Unit
AVP in the Sponsored-Connectivity-Data AVP in the AA-Request.
NOTE:
If the AF is in the user plane, the AF can handle the usage monitoring and therefore it is not required to
provide a usage threshold to the PCRF as part of the sponsored data connectivity information.
ETSI
16
ETSI TS 129 214 V12.5.0 (2014-10)
The PCRF shall process the received Service Information according the operator policy and may decide whether the
request is accepted or not. If the updated Service Information is not acceptable (e.g. subscribed guaranteed bandwidth
for a particular user is exceeded), the PCRF shall indicate in the AA-Answer the cause for the rejection with the
Experimental-Result-Code AVP set to the value REQUESTED_SERVICE_NOT_AUTHORIZED. The PCRF may
additionally provide the acceptable bandwidth within the Acceptable-Service-Info AVP.
If accepted, the PCRF shall update the Service Information with the new information received. Due to the updated
Service Information, the PCRF may need to create, modify or delete the related PCC rules and provide the updated
information towards the PCEF following the corresponding procedures specified at 3GPP TS 29.212 [8]. The
procedures to update the Authorized QoS for the affected IP-CAN bearer are also specified at 3GPP TS 29.212 [8].
The PCRF shall reply with an AA-Answer to the AF. The acknowledgement towards the AF should take place before or
in parallel with any required PCC Rule provisioning towards the PCEF and shall include the Access-NetworkCharging-Identifier(s) and may include the Access-Network-Charging-Address AVP, if they are available at this
moment and have not been yet supplied earlier to the AF. The AA-Answer message shall include the IP-CAN-Type
AVP if such information is available and has not yet been supplied earlier to the AF. In that case, the AA-Answer
message shall also include the RAT-Type AVP when applicable for the specific IP-CAN Type (e.g. 3GPP IP-CAN
Type). In addition, if IP flow mobility applies to service data flows as specified in 3GPP TS 29.212 [8], such that a
subset of the flows within the AF session are affected, the PCRF shall also include IP-CAN-type and RAT-type
information (if applicable) to IP flow mobility related flows, if such information is available and has not yet been
supplied earlier to the AF. The IP flow mobility affected service data flows are included within the Flows AVP at
command level. If the PCRF needs to terminate the Rx session before it has sent the AA Answer, the PCRF shall send
the AA Answer immediately and before the AS Request. If the PCRF does not have an existing session for the Rx
session being modified (such as after a PCRF failure), the PCRF may reject the request with an AA-Answer with the
result code set to DIAMETER_UNKNOWN_SESSION_ID.
If the PCRF modifies existing PCC/QoS rules based on the updated service information and the modification fails due
to resource allocation failure as specified in 3GPP TS 29.212 [8] and if requested by the AF, the PCRF shall send an
RAR command to the AF with the Specific-Action AVP set to the value
INDICATION_OF_FAILED_RESOURCES_ALLOCATION to report the modification failure. The AF shall send an
RAA command to acknowledge the RAR command.
4.4.3
Gate Related Procedures
Depending on the application, in the Service Information provision, the AF may instruct the PCRF when the IP flow(s)
are to be enabled or disabled to pass through the IP-CAN. The AF does this by sending the AA-Request message
containing the Media-Component- Description AVP(s) that contains the flow status information (in the Flow-Status
AVP) for the flows to be enabled or disabled.
In response to this action the PCRF shall set the appropriate gate status for the corresponding active PCC rule(s).
If a Media-Sub-Component AVP under a Media-Component-Description AVP contains a Flow-Usage AVP with the
value RTCP, then the corresponding RTCP IP Flows in both directions shall be enabled even if the Flow-Status AVP
under the Media-Sub-Component AVP is set to ENABLED-UPLINK, ENABLED-DOWNLINK, ENABLED, or
DISABLED.
The PCRF shall reply with an AA-Answer and shall include the Access-Network-Charging-Identifier(s) available at this
moment. The PCRF forwards the AF decision to enable or disable the authorized IP flows.
The behaviour when the AF does not receive the AAA, or when it arrives after the internal timer waiting for it has
expired, or when it arrives with an indication different than DIAMETER_SUCCESS, are outside the scope of this
specification and based on operator policy.
4.4.4
AF Session Termination
When an AF session is terminated, if the AF had received a successful AA-Answer for the initial AA-Request, the AF
shall send a Session-Termination-Request command to the PCRF. Otherwise, the AF shall wait for the initial AAAnswer to be received prior to sending the Session-Termination-Request command to the PCRF.
When the PCRF receives a ST-Request from the AF, indicating an AF session termination, it shall acknowledge that
request by sending a ST-Answer to the AF. Afterwards, it shall free the resources allocated for the corresponding
Service Data Flow(s). In order to do that, the PCRF shall initiate the request for the removal of any related PCC/QoS
ETSI
17
ETSI TS 129 214 V12.5.0 (2014-10)
rules from the PCEF/BBERF and for the update of the Authorized QoS for the affected IP-CAN bearer following the
corresponding procedures specified at 3GPP TS 29.212 [8]. However, if the AF requests the reporting of access
network information within the ST-Request or if the AF provided a threshold for the sponsored data connectivity, the
PCRF shall defer sending the ST-Answer as described below.
If the AF session being terminated corresponds to an MPS session, the PCRF may revoke the actions related to the
prioritization of the MPS session in the corresponding IP-CAN as defined in 3GPP TS 29.212 [8]. For Multimedia
Priority Service handling, see Annex A.9.
If the AF session being terminated corresponds to the last Group Communication session for the IP-CAN session, the
PCRF may revoke the actions related to the prioritization of the Group Communication session as specified in 3GPP TS
29.212 [8].
For sponsored data connectivity, and if a volume threshold was provided for the sponsored data connection at initial
provisioning of session information (subclause 4.4.1) or modification of session information (subclause 4.4.2)
procedures, the PCRF shall provide the volume consumed to the AF. For such purpose, the PCRF shall initiate the IPCAN session modification procedure according 3GPP TS 29.212 [8] in order to obtain the consumed volume. The
PCRF shall send then the ST-Answer to the AF including the Used-Service-Unit AVP for reporting accumulated usage
within the Sponsored-Connectivity-Data AVP.
If the AF requires access network information at this step, the AF shall include the Required-Access-Info AVP within
the ST-Request command, indicating the required information. In this case, the PCRF shall initiate the IP-CAN session
modification procedure according to 3GPP TS 29.212 [8]. The PCRF shall send then the ST-Answer to the AF
including the required data within the 3GPP-User-Location-Info AVP (if available), TWAN-Identifier AVP (if
available), User-Location-Info-Time AVP (if available), 3GPP-SGSN-MCC-MNC AVP (if location info is not
available) and/or 3GPP-MS-TimeZone AVP (if available).
4.4.5
Subscription to Notification of Signalling Path Status
An AF may subscribe to notifications of the status of the AF Signalling transmission path. To do so, the AF shall open
an Rx Diameter session with the PCRF for the AF signalling using an AA-Request command. The AF shall provide the
UE"s IP address (using either the Framed-IP-Address AVP or the Framed-Ipv6-Prefix AVP) and the Specific-Action
AVP requesting the subscription to 'INDICATION_OF_LOSS_OF BEARER' and/or
'INDICATION_OF_RELEASE_OF_BEARER'. The AF shall additionally provide a Media-Component-Description
AVP including a single Media-Sub-Component AVP with the Flow-Usage AVP set to the value 'AF_SIGNALLING'.
The Media-Component-Description AVP shall contain the Media-Component-Number AVP set to '0'.
If the procedures in Clause 4.4.5a are not applied, the Media-Sub-Component AVP shall contain the Flow-Number
AVP set to '0', and the rest of AVPs within the Media-Component-Description and Media-Sub-Component AVPs shall
not be used in this case.
When the PCRF receives an AA-Request as described in the preceding paragraph from the AF, the PCRF shall perform
session binding as described in 3GPP TS 29.213 [9] and acknowledges the AAR command by sending an AA-Answer
command to the AF.
PCC/QoS Rules related to AF Signalling IP Flows should be provisioned to PCEF/BBERF using the corresponding
procedures specified at 3GPP TS 29.212 [8] at an earlier stage (e.g. typically at the establishment of the IP-CAN bearer
dedicated for AF Signalling IP Flows). The PCRF may install the corresponding dynamic PCC/QoS rule for the AF
signalling IP flows if none has been installed before.
NOTE 1: Well-known ports (e.g. 3GPP TS 24.229 [17] for SIP) or wildcard ports can be used by PCRF to derive
the dynamic PCC/QoS rule for the AF signalling IP flows.
If the Rx Diameter Session is only used for subscription to Notification of Signalling Path Status, the AF may cancel the
subscription to notifications of the status of the AF Signalling transmission path. In that case, the AF shall use a
Session-Termination-Request (STR) command to the PCRF, which shall be acknowledged with a Session-TerminationAnswer (STA) command.
NOTE 2: The Rx Diameter Session created for the AF signalling can also be used when the AF requests
notifications of IP-CAN type change and/or when the AF provisions AF Signalling Flow Information.
ETSI
4.4.5a
18
ETSI TS 129 214 V12.5.0 (2014-10)
Provisioning of AF Signalling Flow Information
This sub-clause is applicable when IMS restoration is supported according to supported feature ProvAFsignalFlow as
described in sub-clause 5.4.1.
An AF may provision information about the AF signalling IP flows between the UE and the AF. To do so, the AF shall
make use of an Rx Diameter session already opened with the PCRF if an Rx Diameter session related to the AF
signalling is already established. The AF may modify an already open Rx Diameter session related to the AF signalling
(e.g. an Rx Diameter session established for the purpose of subscription to notification of signalling path status as
described in 4.4.5) or it may open a new Rx Diameter session related to the AF signalling if none exists.
To provision the AF signalling flow information the AF shall provide the UE"s IP address using either Framed-IPAddress AVP or Framed-Ipv6-Prefix AVP. The AF shall additionally provide a Media-Component-Description AVP
including one or more Media-Sub-Component AVP(s) representing the AF signalling IP flows. The Media-ComponentDescription AVP shall contain the Media-Component-Number AVP set to '0'. Each Media-Sub-Component AVP
representing an AF signalling IP flow shall contain the Flow-Number AVP set according to the rules described in
Annex B and one or two Flow-Description AVP(s) set to the IP flows of the AF signalling. Additionally, the MediaSub-Component AVP shall include the Flow-Usage AVP set to the value 'AF_SIGNALLING', the Flow-Status AVP set
to 'ENABLED' and the AF-Signalling-Protocol AVP set to the value corresponding to the signalling protocol used
between the UE and the AF.
When the PCRF receives from the AF an AA-Request as described in the preceding paragraph, the PCRF shall perform
session binding as described in 3GPP TS 29.213 [9] and shall acknowledge the AAR command by sending an
AA-Answer command to the AF.
PCC/QoS Rules related to the AF signalling IP flows could have been provisioned to PCEF/BBERF using the
corresponding procedures specified in 3GPP TS 29.212 [8] at an earlier stage (e.g. typically at the establishment of the
IP-CAN bearer dedicated for AF Signalling IP Flows). The PCRF shall install the corresponding dynamic PCC/QoS
rule for the AF signalling IP flows.
The AF may de-provision the information about the AF signalling IP flows at any time. To do that, if the Rx Diameter
session is only used to provide information about the AF Signalling IP flows, the AF shall close the Rx Diameter
session by sending a Session-Termination-Request (STR) command to the PCRF, which shall be acknowledged with a
Session-Termination-Answer (STA) command. Otherwise, the AF shall remove the IP flows within the Media-SubComponent AVP by supplying the Flow-Status AVP with value 'REMOVED'. In both cases, the PCRF shall remove the
corresponding dynamic PCC/QoS rule for the AF signalling IP flows.
4.4.6
4.4.6.1
Traffic Plane Events

IP-CAN Session Termination
When an IP-CAN session is terminated, the PCRF shall inform the AF about the IP-CAN session termination by
sending an ASR (abort session request) command to the AF on each active Rx Diameter session.
When the AF receives the ASR command, it shall acknowledge the command by sending an ASA (abort session
answer) command to the PCRF and indicate the termination of the session by sending an STR (session termination
request) command to the PCRF. The PCRF shall acknowledge the termination of the session by sending an STA
(session termination answer) command to the AF.
Signalling flows for IP-CAN session termination cases are presented in 3GPP TS 29.213 [9].
4.4.6.2
Service Data Flow Deactivation
It may happen that one or more PCC/QoS Rules (i.e. Service Data Flows) are deactivated at the PCEF/BBERF at a
certain time, either permanently or temporarily. When the PCRF gets the knowledge that one or more SDFs have been
deactivated, (e.g. due to a bearer release or loss of bearer or out of credit condition), the PCRF shall inform the AF
accordingly if the AF has previously subscribed using the Specific-Action AVP in the AAR command.
When not all the service data flows within the AF session are affected, the PCRF shall inform the AF by sending an
RAR (re-authorization request) command. The RAR command shall include the deactivated IP Flows encoded in the
Flows AVP and the cause encoded in the Specific-Action AVP.
ETSI
19
ETSI TS 129 214 V12.5.0 (2014-10)
When the AF receives the RAR command, it shall acknowledge the command by sending an RAA (re-authorization
answer) command to the PCRF. The AF may also update the session information by sending an AAR (AA-request)
command to the PCRF.
If the PCRF receives the AAR command, it shall acknowledge the command by sending an AAA (AA-answer)
command to the AF.
When all the service data flows within the AF session are affected, the PCRF shall inform the AF by sending an ASR
command on the Rx Diameter session related to the AF session. When the AF receives the ASR command, it shall
acknowledge the command by sending an ASA (abort session answer) command to the PCRF. After that the AF shall
initiate an AF session termination procedure as defined in clause 4.4.4.
Signalling flows for Service Data Flow Deactivation cases are presented in 3GPP TS 29.213 [9].
4.4.6.3
Notification of Signalling Path Status
In the event that the PCRF is notified of the loss or release of resources associated to the PCC/QoS Rules corresponding
with AF Signalling IP Flows, the PCRF shall inform the AF about the Loss of the Signalling Transmission path by
sending a Re-Authorization Request (RAR) command to the AF. The RAR shall include the Specific-Action AVP set to
the value 'INDICATION_OF_LOSS_OF_BEARER' or 'INDICATION_OF_RELEASE_OF_BEARER' and the
deactivated IP Flow encoded in the Flows AVP.
NOTE:
According to the standardized QCI characteristics as defined in 3GPP TS 23.203[2], the IMS signalling
specific PCC rules include a QCI corresponding to a non-GBR bearer. When these guidelines are
followed, the INDICATION_OF_LOSS_OF_BEARER will not be reported.
When the AF receives the RAR command, it shall acknowledge the command by sending an RAA command to the
PCRF.
The AF may then decide to terminate the Rx Diameter session used for the notification of the status of the AF
Signalling transmission path. The AF may also decide to terminate any other active Rx Diameter session with the PCRF
related to the AF Signalling which is not available any longer. In that case, the AF shall then initiate the AF
Termination procedure towards the PCRF as defined in clause 4.4.4.
4.4.6.4
IP-CAN type change Notification
If the AF has successfully subscribed to change notifications in UE"s IP-CAN type and RAT type, the PCRF shall
provide the UE"s IP-CAN type and RAT type in the AA-Answer if already known by the PCRF. The PCRF shall also
send an RAR command when a corresponding event occurs, i.e. when the UE"s IP-CAN type or RAT type (if the IPCAN type is GPRS), changes or becomes available. In this case the RAR from the PCRF shall include the SpecificAction AVP for the subscribed event and include the IP-CAN-Type AVP and RAT-Type AVP (in case of 3GPP
IP-CAN) for the UE"s new IP-CAN/RAT. If the PCRF is informed of an IP-CAN type change due to IP flow mobility
as specified in 3GPP TS 29.212 [8], where a subset the flows within the AF session are affected, the PCRF shall include
IP-CAN-type and RAT-type information (if applicable) to IP flow mobility affected service data flows. The IP flow
mobility affected service data flows are included within the Flows AVP at command level.
NOTE:
4.4.6.5
The RAT type event is only applicable for IP-CAN type GPRS, the PCRF will provide the RAT type
information to the AF not only in case of GPRS IP-CAN type, but also in case of other 3GPP IP-CAN
types.
Access Network Charging Information Notification
If the AF has subscribed to a notification about Access Network Charging Information, the PCRF shall provide the
Access Network Charging Information in the response, if already known by the PCRF. If not available, the PCRF shall
provide the Access Network Charging Information by sending a Re-Authorization-Request (RAR) command when the
Access Network Charging Information is received from the PCEF. If different Access Network Charging Information is
applicable to the IP-CAN session, the PCRF shall notify the AF about the Access Network Charging Information that
applies to each authorized flow. The RAR shall include the Specific-Action AVP set to the value
'CHARGING_CORRELATION_EXCHANGE' and shall include the assigned Access-Network-Charging-Identifier(s)
and may include the Access-Network-Charging-Address AVP.
ETSI
4.4.6.6
20
ETSI TS 129 214 V12.5.0 (2014-10)
Reporting Usage for Sponsored Data Connectivity
When the AF session is associated with a sponsor and the AF provided usage monitoring thresholds for such sponsor
to the PCRF when the Rx Diameter session was established or modified, the PCRF shall report accumulated usage to
the AF, when
-
the PCRF detects that the usage threshold provided by the AF has been reached; or
the AF session is terminated by the AF ; or
the AF session is terminated due to the IP-CAN session termination or the home operator policy disallowing the
UE accessing the sponsored data connectivity in the roaming case.
When the PCRF detects that the usage threshold has been reached, the PCRF shall report the accumulated usage as
provided by the PCEF to the AF in a RA-Request (RAR) command with the Specific-Action AVP set to the value
USAGE_REPORT Otherwise, when the AF session is terminated by the AF or the AF session is terminated due to the
IP-CAN session termination or the home operator policy disallowing the UE accessing the sponsored data connectivity
in the roaming case, the PCRF shall report the accumulated usage as provided by the PCEF to the AF in ST-Answer
(STA) command..
The accumulated usage shall be reported in the Used-Service-Unit AVP within the Sponsored-Connectivity-Data AVP.
If the AF receives a RAR command indicating the usage threshold is reached, the AF may terminate the AF session or
provide a new usage threshold in the Granted-Service-Unit AVP within the Sponsored-Connectivity-Data AVP to the
PCRF in the AAR ignall. Alternatively, the AF may allow the session to continue without providing new usage
threshold in the AAR command.
NOTE:
4.4.6.7
After the PCRF reports the accumulated usage to the AF, the AF can provide a new usage threshold to
the PCRF. The monitoring will not start until the PCRF receives the new threshold from the AF and
provide it to the PCEF
Reporting Access Network Information
If the AF requests the PCRF to report the access network information (e.g. user location and/or user timezone
information), the AF shall subscribe to the 'ACCESS_NETWORK_INFO_REPORT' within the Specific-Action AVP
and shall include the required access network information within the Required-Access-Info AVP. The AF may request
the PCRF to report the access network information in conjunction with providing the PCRF with the AF session
information, refer to subclause 4.4.1. Optionally, the AF may request the PCRF to report the access network
information without providing service information (see subclause A.10.2). In the latter case the AF establishes an Rx
session for the AF session upon requesting the access network information from the PCRF with an AA-Request
command, containing information required for the session binding in the Framed-IP-Address AVP, the Framed-Ipv6Prefix AVP Subscription-Id AVP, the Called-Station-Id AVP and/or the IP-Domain-Id AVP.
The AF may also request the PCRF to report the access network information at Rx session termination. To do so, the
AF shall include the required access network information within the Required-Access-Info AVP in the corresponding
ST-Request.
When the PCRF receives a request to report the access network information from the AF in an AAR command or in an
STR command triggered by the AF, if the PCRF determines that the access network does not support the access
network information reporting based on the currently used IP-CAN type or the values of RAT-Type AVP and ANTrusted AVP or the PCEF/BBERF does not support the access network information reporting based on the SupportedFeature AVP, the PCRF shall respond to AF with an AAA or STA command including the NetLoc-Access-Surpport
AVP set to the value of 0 (NETLOC_ACCESS_NOT_SUPPORTED); otherwise, it shall immediately configure the
PCEF or BBERF to provide such access network information.
When the PCRF then receives the requested access network information from the PCEF/BBERF, the PCRF shall
provide the corresponding access network information to the AF within the 3GPP-User-Location-Info AVP (if
available), TWAN-Identifier AVP (if available), User-Location-Info-Time AVP (if available), 3GPP-SGSN-MCCMNC AVP (if location info is not available) and/or 3GPP-MS-TimeZone AVP and the RAN-NAS-Release-Cause AVP
(if available) in the RAR command if the Rx session is not being terminated or in the STA command if the Rx session is
being terminated. If the information is provided in the RAR command, PCRF shall also provide the
ACCESS_NETWORK_INFO_REPORT within Specific-Action AVP.
ETSI
21
ETSI TS 129 214 V12.5.0 (2014-10)
When the PCRF receives a request to report the access network information from the AF in an STR command that was
initiated as part of an IP-CAN session termination procedure, the PCRF shall provide the requested access information
previously provided by the PCEF/BBERF in the corresponding STA command. The PCRF shall provide the serving
PLMN identifier within 3GPP-SGSN-MCC-MNC AVP to the AF if the user location information is not available.
NOTE:
The 3GPP GPRS and 3GPP EPS support access network information reporting in this release.
The PCRF shall not report any subsequently received access network information to the AF, unless the AF sends a new
request for access network information.
4.4.6.8
Temporary Network Failure handling
If the PCRF detects that a temporary network failure has occurred (e.g. the SGW has failed for 3GPP-EPS access as
defined in subclause B.3.14 of 3GPP TS 29.212 [8]) and the AF requests an AF session establishment or modification
in an AA-Request command, the PCRF shall respond to the AF with an AA-Answer including the Experimental-ResultCode AVP set to the value TEMPORARY_NETWORK_FAILURE.
If the PCRF detects that a temporary network failure has occurred (e.g. the SGW has failed for 3GPP-EPS access) and
the AF requests an AF session termination in a ST-Request command, the PCRF shall respond with successful ResultCode AVP to the AF.
NOTE 1: Actions over Gx/Gxx reference point when there is a temporary network failure are described in 3GPP TS
29.212 [8]. For example, for S-GW Restoration procedures the PCRF will wait for the SGW recovery
before deleting the corresponding PCC/QoS rules,according to subclause B.3.14 in that specification.
If the PCRF detects that the PCC/QoS rules related to an AF session cannot be installed or modified because there is a
temporary network failure (e.g. SGW failed according to subclause B.3.14 in 3GPP TS 29.212 [8]) and if requested by
the AF, the PCRF shall send a RA-Request command to the AF with the Specific-Action AVP set to
INDICATION_OF_FAILED_RESOURCES_ALLOCATION.
4.4.7
P-CSCF Restoration Enhancement Support
This section is applicable when the PCRF-based P-CSCF Restoration Enhancement, as defined in 3GPP
TS 23.380 [33], is supported by both P-CSCF and PCRF.
The P-CSCF acting as AF shall send an AAR command with a P-CSCF Restoration Indication to the PCRF in the case
P-CSCF Restoration needs to be performed. This AAR shall include the following information required by the DRA or
PCRF to find the corresponding IP-CAN session:
-
The UE"s IP address as applicable in the Framed-IP-Address AVP or in the Framed-Ipv6-Prefix AVP. If the IP
address is not unique (e.g. private IPv4 case), the P-CSCF shall also include the IP-Domain-ID AVP if available.
-
If the IP address is not available or if the IP address is not unique and the IP-Domain-ID is not
available, the P-CSCF shall include the IMSI in the Subscription-Id AVP and the APN in the
Called-Station-Id AVP.
The AF shall also include the Auth-Session-State AVP set to the value NO_STATE_MAINTAINED (1) in the AAR
command, as described in IETF RFC 3588 [5]. As a consequence, the PCRF shall not maintain any state information
about this session.
The PCRF shall acknowledge the AAR command by sending an AAA command to the P-CSCF acting as AF and shall
include the Auth-Session-State AVP set to NO_STATE_MAINTAINED (1). The PCRF shall send a request for PCSCF Restoration to the PCEF for the corresponding IP-CAN session.
Editor"s Note: It is ffs if a supported-feature is needed for P-CSCF and PCRF to indicate if they support P-CSCF
restoration procedure.
ETSI
Rx protocol
5.1
Protocol support
22
ETSI TS 129 214 V12.5.0 (2014-10)
The Rx interface in the present release is based on Rx and Gq protocols defined for Release 6 as specified in 3GPP TS
29.211 [7] and 3GPP TS 29.209 [5] respectively. However, to be able to separate the policy and charging rules function
(PCRF) of the present release from the policy decision function (PDF) and charging rules function (CRF) of Release 6,
the Rx application in the present release has an own vendor specific Diameter application.
The Rx application is defined as an IETF vendor specific Diameter application, where the vendor is 3GPP and the
Application-ID for the Rx application in the present release is 16777236. The vendor identifier assigned by IANA to
3GPP (http://www.iana.org/assignments/enterprise-numbers) is 10415.
NOTE:
A route entry can have a different destination based on the application identification AVP of the message.
Therefore, Diameter agents (relay, proxy, redirection, translation agents) must be configured
appropriately to identify the 3GPP Rx application within the Auth-Application-Id AVP in order to create
suitable routeing tables.
Due to the definition of the commands used in Rx protocol, there is no possibility to skip the Auth-Application-Id AVP
and use the Vendor-Specific-Application-Id AVP instead. Therefore the Rx application identification shall be included
in the Auth-Application-Id AVP.
With regard to the Diameter protocol defined over the Rx reference point, the PCRF acts as a Diameter server, in the
sense that it is the network element that handles AF session authorization requests for a particular realm. The AF acts as
the Diameter client, in the sense that is the network element requesting the authorization of resources for an AF session.
5.2
Initialization, maintenance and termination of connection

and session
The initialization and maintenance of the connection between each AF and PCRF pair is defined by the underlying
protocol. Establishment and maintenance of connections between Diameter nodes is described in RFC 3588 [10].
After establishing the transport connection, the PCRF and the AF shall advertise the support of the Rx specific
Application by including the value of the application identifier in the Auth-Application-Id AVP and the value of the
3GPP (10415) in the Vendor-Id AVP of the Vendor-Specific-Application-Id AVP contained in the
Capabilities-Exchange-Request and Capabilities-Exchange-Answer commands. The Capabilities-Exchange-Request
and Capabilities-Exchange-Answer commands are specified in the Diameter Base Protocol (RFC 3588 [10]).
The termination of the Diameter user session is specified in RFC 3588 [10] in clauses 8.4 and 8.5. The description of
how to use of these termination procedures in the normal cases is embedded in the procedures description (clause 4.4).
5.3
Rx specific AVPs
Table 5.3.1 describes the Diameter AVPs defined for the Rx interface protocol, their AVP Code values, types, possible
flag values, whether or not the AVP may be encrypted and which supported feature the AVP is applicable to. The
Vendor-Id header of all AVPs defined in the present document shall be set to 3GPP (10415).
NOTE:
Most of these AVPs have already been defined in 3GPP TS 29.209 [5] for Rel-6. Their definition is based
on the one used for Rel-6 with some possible modifications to be applied to the Rel-7 protocols.
ETSI
23
ETSI TS 129 214 V12.5.0 (2014-10)
Table 5.3.1: Rx specific Diameter AVPs

Attribute Name
AVP
Code
500
501
AVP Flag rules (note 1)

Clause Value Type Must May Should Must May
defined (note 2)
not
not Encr.
5.3.1
Enumerated M,V P
Y
5.3.2
Address
M,V P
Y
Applicability
(note 3)
Abort-Cause
Access-Network-ChargingAddress
Access-Network-Charging502 5.3.3
Grouped
M,V P
Y
Identifier
Access-Network-Charging503 5.3.4
OctetString M,V P
Y
Identifier-Value
Acceptable-Service-Info
526 5.3.24 Grouped
M,V P
Y
AF-Application-Identifier
504 5.3.5
OctetString M,V P
Y
AF-Charging-Identifier
505 5.3.6
OctetString M,V P
Y
Application-Service-Provider532 5.3.29 UTF8String V
P
M
Y
SponsoredConnectivity
Identity
Codec-Data
524 5.3.7
OctetString M,V P
Y
Flow-Description
507 5.3.8
IPFilterRule M,V P
Y
Flow-Number
509 5.3.9
Unsigned32 M,V P
Y
Flows
510 5.3.10 Grouped
M,V P
Y
Flow-Status
511 5.3.11 Enumerated M,V P
Y
Flow-Usage
Y
GCS-Identifier
538 5.3.36 OctetString V
P
M
Y
GroupComService
Service-URN
525 5.3.23 OctetString M,V P
Y
Specific-Action
Y
Max-Requested-Bandwidth515 5.3.14 Unsigned32 M,V P
Y
DL
Max-Requested-Bandwidth516 5.3.15 Unsigned32 M,V P
Y
UL
Media-Component517 5.3.16 Grouped
M,V P
Y
Description
Media-Component-Number
518 5.3.17 Unsigned32 M,V P
Y
Media-Sub-Component
519 5.3.18 Grouped
M,V P
Y
Media-Type
Y
MPS-Identifier
P
M
Y
Rel10
Min-Requested-Bandwidth-DL 534 5.3.32 Unsigned32 V
P
M
Y
Rel10
Min-Requested-Bandwidth-UL 535 5.3.33 Unsigned32 V
P
M
Y
Rel10
RR-Bandwidth
Y
RS-Bandwidth
Y
Service-Info-Status
Y
SIP-Forking-Indication
Y
Sponsor-Identity
531 5.3.28 UTF8String V
P
M
Y
Sponsored-Connectivity-Data
530 5.3.27 Grouped
V
P
M
Y
SCTimeBasedUM
(NOTE 4)
AF-Signalling-Protocol
529 5.3.26 Enumerated V
P
M
Y
ProvAFsignalFlow
Required-Access-Info
P
M
Y
NetLoc
Rx-Request-Type
P
M
Y
IP-Domain-Id
P
M
Y
NOTE 1: The AVP header bit denoted as "M", indicates whether support of the AVP is required. The AVP header bit
denoted as "V", indicates whether the optional Vendor-ID field is present in the AVP header. For further
details, see RFC 3588 [10].
NOTE 2: The value types are defined in RFC 3588 [10].
NOTE 3: AVPs marked with a supported feature (e.g. 'ProvAFsignalFlow', 'SponsoredConnectivity', 'Rel10' or
'NetLoc') are applicable as described in clause 5.4.1
NOTE 4: Volume Usage monitoring control functionality is applicable for SponsoredConnectivity supported feature.
Time Based Usage monitoring control is applicable for SCTimeBasedUM supported feature.
5.3.1
Abort-Cause AVP
The Abort-Cause AVP (AVP code 500) is of type Enumerated, and determines the cause of an abort session request
(ASR) or of a RAR indicating a bearer release. The following values are defined:
BEARER_RELEASED (0)
ETSI
24
ETSI TS 129 214 V12.5.0 (2014-10)
This value is used when the bearer has been deactivated as a result from normal signalling handling. For
GPRS the bearer refers to the PDP Context.
INSUFFICIENT_SERVER_RESOURCES (1)
This value is used to indicate that the server is overloaded and needs to abort the session.
INSUFFICIENT_BEARER_RESOURCES (2)
This value is used when the bearer has been deactivated due to insufficient bearer resources at a transport
gateway (e.g. GGSN for GPRS).
PS_TO_CS_HANDOVER (3)
This value is used when the bearer has been deactivated due to PS to CS handover.
SPONSORED_DATA_CONNECTIVITY_ DISALLOWED (4)
This value is used in the ASR when the PCRF needs to initiates the AF session termination due to the
operator policy (e.g. disallowing the UE accessing the sponsored data connectivity in the roaming case).
5.3.2
Access-Network-Charging-Address AVP
The Access-Network-Charging-Address AVP (AVP code 501) is of type Address, and it indicates the IP Address of the
network entity within the access network performing charging (e.g. the GGSN IP address). The
Access-Network-Charging-Address AVP should not be forwarded over an inter-operator interface.
5.3.3
Access-Network-Charging-Identifier AVP
The Access-Network-Charging-Identifier AVP (AVP code 502) is of type Grouped, and contains a charging identifier
(e.g. GCID) within the Access-Network-Charging-Identifier-Value AVP along with information about the flows
transported within the corresponding bearer within the Flows AVP. If no Flows AVP is provided, the
Access-Network-Charging-Identifier-Value applies for all flows within the AF session.
The Access-Network-Charging-Identifier AVP can be sent from the PCRF to the AF. The AF may use this information
for charging correlation with session layer.
AVP Format:
Access-Network-Charging-Identifier ::= < AVP Header: 502 >
{ Access-Network-Charging-Identifier-Value}
*[ Flows ]
5.3.4
Access-Network-Charging-Identifier-Value AVP
The Access-Network-Charging-Identifier-Value AVP (AVP code 503) is of type OctetString, and contains a charging
identifier (e.g. GCID).
5.3.5
AF-Application-Identifier AVP
The AF-Application-identifier AVP (AVP code 504) is of type OctetString, and it contains information that identifies
the particular service that the AF service session belongs to. This information may be used by the PCRF to differentiate
QoS for different application services.
For example the AF-Application-Identifier may be used as additional information together with the Media-Type AVP
when the QoS class for the bearer authorization at the Gx interface is selected. The AF-Application-Identifier may be
used also to complete the QoS authorization with application specific default settings in the PCRF if the AF does not
provide full Session-Component-Description information.
ETSI
5.3.6
25
ETSI TS 129 214 V12.5.0 (2014-10)
AF-Charging-Identifier AVP
The AF-Charging-Identifier AVP (AVP code 505) is of type OctetString, contains the AF Charging Identifier that is
sent by the AF. This information may be used for charging correlation with bearer layer.
5.3.7
Codec-Data AVP
The Codec-Data AVP (AVP code 524) is of type OctetString.

The Codec-Data AVP shall contain codec related information known at the AF. This information shall be encoded as
follows:
-
The first line of the value of the Codec-Data AVP shall consist of either the word 'uplink' or the word 'downlink'
(in ASCII, without quotes) followed by a new-line character. The semantics of these words are the following:
-
'uplink' indicates that the SDP was received from the UE and sent to the network.
'downlink' indicates that the SDP was received from the network and sent to the UE.
NOTE:
The first line indicates the direction of the source of the SDP used to derive the information. The majority
of the information within the Codec-Data AVP indicating 'downlink' describes properties, for instance
receiver capabilities, of the sender of the SDP, the network in this case and is therefore applicable for IP
flows in the uplink direction. Similarly, the majority of the information within the Codec-Data AVP
indicating 'uplink' describes properties, for instance receiver capabilities, of the sender of the SDP, the UE
in this case and is therefore applicable for IP flows in the downlink direction.
The second line of the value of the Codec-Data AVP shall consist of either the word 'offer' or the word 'answer',
or the word 'description' (in ASCII, without quotes) followed by a new-line character. The semantics of these
words are the following:
-
'offer' indicates that SDP lines from an SDP offer according to RFC 3264 [18] are being provisioned in the
Codec-Data AVP;
'answer' indicates that SDP lines from an SDP answer according to RFC 3264 [18] are being provisioned in
the Codec-Data AVP;
'description' indicates that SDP lines from a SDP session description in a scenario where the offer-answer
mechanism of RFC 3264 [18] is not being applied are being provisioned in the Codec-Data AVP. For
instance, SDP from an RTSP 'Describe' reply may be provisioned.
The rest of the value shall consist of SDP line(s) in ASCII encoding separated by new-line characters, as
specified in IETF RFC 4566 [13]. The first of these line(s) shall be an 'm' line. The remaining lines shall be any
available SDP 'a' and 'b' lines related to that 'm' line. However, to avoid duplication of information, the SDP
'a=sendrecv', 'a=recvonly ', 'a=sendonly', 'a=inactive', 'b:AS', 'b:RS' and 'b:RR' lines do not need to be included.
5.3.8
Flow-Description AVP
The Flow-Description AVP (AVP code 507) is of type IPFilterRule, and defines a packet filter for an IP flow with the
following information:
-
Direction (in or out). The direction 'in' refers to uplink IP flows, and the direction 'out' refers to downlink IP
flows.
Source and destination IP address (possibly masked).
Protocol.
Source and destination port.
The IPFilterRule type shall be used over Rx interface with the following restrictions:
-
The Source Port may be omitted to indicate that any source port is allowed. Lists or ranges shall not be used.
ETSI
26
Only the Action 'permit' shall be used.
No 'options' shall be used.
The invert modifier '!' for addresses shall not be used.
The keyword 'assigned' shall not be used.
NOTE:
ETSI TS 129 214 V12.5.0 (2014-10)
For TCP protocol, destination port can also be omitted.
If any of these restrictions is not observed by the AF, the server shall send an error response to the AF containing the
Experimental-Result-Code AVP with value FILTER_RESTRICTIONS.
For the Rx interface, the Flow description AVP shall be used to describe a single IP flow.
5.3.9
Flow-Number AVP
The Flow-Number AVP (AVP code 509) is of type Unsigned32, and it contains the ordinal number of the IP flow(s),
assigned according to the rules in Annex B.
5.3.10
Flows AVP
The Flows AVP (AVP code 510) is of type Grouped, and it indicates IP flows via their flow identifiers.
When reporting an out of credit condition, the Final-Unit-Action AVP indicates the termination action applied to the
impacted flows.
If no Flow-Number AVP(s) are supplied, the Flows AVP refers to all Flows matching the media component number.
AVP Format:
Flows::= < AVP Header: 510 >
{Media-Component-Number}
*[Flow-Number]
[Final-Unit-Action]
5.3.11
Flow-Status AVP
The Flow-Status AVP (AVP code 511) is of type Enumerated, and describes whether the IP flow(s) are enabled or
disabled. The following values are defined:
ENABLED-UPLINK (0)
This value shall be used to enable associated uplink IP flow(s) and to disable associated downlink IP flow(s).
ENABLED-DOWNLINK (1)
This value shall be used to enable associated downlink IP flow(s) and to disable associated uplink IP flow(s).
ENABLED (2)
This value shall be used to enable all associated IP flow(s) in both directions.
DISABLED (3)
This value shall be used to disable all associated IP flow(s) in both directions.
REMOVED (4)
This value shall be used to remove all associated IP flow(s). The IP Filters for the associated IP flow(s) shall
be removed. The associated IP flows shall not be taken into account when deriving the authorized QoS.
NOTE:
The interpretation of values for the RTCP flows in the Rx interface is described within the procedures in
clause 4.4.3.
ETSI
5.3.12
27
ETSI TS 129 214 V12.5.0 (2014-10)
Flow-Usage AVP
The Flow-Usage AVP (AVP code 512) is of type Enumerated, and provides information about the usage of IP Flows.
The following values are defined:
NO_INFORMATION (0)
This value is used to indicate that no information about the usage of the IP flow is being provided.
RTCP (1)
This value is used to indicate that an IP flow is used to transport RTCP.
AF_SIGNALLING (2)
This value is used to indicate that the IP flow is used to transport AF Signalling Protocols (e.g. SIP/SDP).
NO_INFORMATION is the default value.
NOTE:
5.3.13
An AF may choose not to identify RTCP flows, e.g. in order to avoid that RTCP flows are always
enabled by the server.
Specific-Action AVP
The Specific-Action AVP (AVP code 513) is of type Enumerated.

Within a PCRF initiated Re-Authorization Request, the Specific-Action AVP determines the type of the action.
Within an initial AA request the AF may use the Specific-Action AVP to request any specific actions from the server at
the bearer events and to limit the contact to such bearer events where specific action is required. If the Specific-Action
AVP is omitted within the initial AA request, no notification of any of the events defined below is requested at this
time.
For one time specific actions, as identified in the value descriptions below, the AF may also provide the Specific-Action
AVP with the applicable one-time-specific-action value(s) in subsequent AA-Requests. Non-one-time-specific-action
value(s) may only be provided in the initial AA-Request and shall then be applicable for the entire lifetime of the Rx
session.
NOTE 1: One time specific actions are reported once the required action is fulfilled and are not reported again
unless the AF sends a new request.
NOTE 2: Unless otherwise stated in the definition of the specific action value, when the AF requests specific
actions in the initial AA-Request, the PCRF reports that action whenever new related information is
available during the lifetime of the Rx session.
NOTE 2a: Whether the PCRF decides to report INDICATION_OF_RELEASE_OF_BEARER (4) or
INDICATION_OF_FAILED_RESOURCES_ALLOCATION (9) upon receipt of a bearer failure from
the PCEF is left to the implementation.
Void (0)
CHARGING_CORRELATION_EXCHANGE (1)
Within a RAR, this value shall be used when the server reports the access network charging identifier to the AF.
The Access-Network-Charging-Identifier AVP shall be included within the request. In the AAR, this value
indicates that the AF requests the server to provide the access network charging identifier to the AF for each
authorized flow, when the access network charging identifier becomes known at the PCRF.
INDICATION_OF_LOSS_OF_BEARER (2)
Within a RAR, this value shall be used when the server reports a loss of a bearer (in the case of GPRS PDP
context bandwidth modification to 0 kbit for GBR bearers) to the AF. The SDFs that are deactivated as a
ETSI
28
ETSI TS 129 214 V12.5.0 (2014-10)
consequence of this loss of bearer shall be provided within the Flows AVP. In the AAR, this value indicates that
the AF requests the server to provide a notification at the loss of a bearer.
INDICATION_OF_RECOVERY_OF_BEARER (3)
Within a RAR, this value shall be used when the server reports a recovery of a bearer (in the case of 3GPPGPRS or 3GPP-EPS when PGW interoperates with a Gn/Gp SGSN, PDP context bandwidth modification from 0
kbit to another value for GBR bearers) to the AF. The SDFs that are re-activated as a consequence of the
recovery of bearer shall be provided within the Flows AVP. In the AAR, this value indicates that the AF requests
the server to provide a notification at the recovery of a bearer.
INDICATION_OF_RELEASE_OF_BEARER (4)
Within a RAR, this value shall be used when the server reports the release of a bearer (e.g. PDP context removal
for 3GPP-GPRS or bearer/PDP context removal for 3GPP-EPS) to the AF. The SDFs that are deactivated as a
consequence of this release of bearer shall be provided within the Flows AVP. In the AAR, this value indicates
that the AF requests the server to provide a notification at the removal of a bearer.
Void (5)
IP-CAN_CHANGE (6)
This value shall be used in RAR command by the PCRF to indicate a change in the IP-CAN type or RAT type (if
the IP-CAN type is GPRS). When used in an AAR command, this value indicates that the AF is requesting
subscription to IP-CAN change and RAT change notification. When used in RAR it indicates that the PCRF
generated the request because of an IP-CAN or RAT change. IP-CAN-Type AVP and RAT-Type AVP (in case
of 3GPP IP-CAN) shall be provided in the same request with the new/valid value(s).
If an IP-CAN type or RAT type change is due to IP flow mobility and a subset of the flows within the AF
session is affected, the affected service data flows shall be provided in the same request.
INDICATION_OF_OUT_OF_CREDIT (7)
Within a RAR, this value shall be used when the PCRF reports to the AF that SDFs have run out of credit, and
that the termination action indicated by the corresponding Final-Unit-Action AVP applies (3GPP TS 32.240 [23]
and 3GPP TS 32.299 [24]. The SDFs that are impacted as a consequence of the out of credit condition shall be
provided within the Flows AVP. In the AAR, this value indicates that the AF requests the PCRF to provide a
notification of SDFs for which credit is no longer available. Applicable to functionality introduced with the Rel8
feature as described in subclause 5.4.1.
INDICATION_OF_SUCCESSFUL_RESOURCES_ALLOCATION (8)
Within a RAR, this value shall be used by the PCRF to indicate that the resources requested for particular service
information have been successfully allocated. The SDFs corresponding to the resources successfully allocated
shall be provided within the Flows AVP.
In the AAR, this value indicates that the AF requests the PCRF to provide a notification when the resources
associated to the corresponding service information have been allocated.
Applicable to functionality introduced with the Rel8 feature as described in subclause 5.4.1.
NOTE 3: This value applies to applications for which the successful resource allocation notification is required
for their operation since subscription to this value impacts the resource allocation signalling overhead
towards the PCEF/BBERF.
INDICATION_OF_FAILED_RESOURCES_ALLOCATION (9)
Within a RAR, this value shall be used by the PCRF to indicate that the resources requested for a particular
service information cannot be successfully allocated. The SDFs corresponding to the resources that could not be
allocated shall be provided within the Flows AVP.
In the AAR, this value indicates that the AF requests the PCRF to provide a notification when the resources
associated to the corresponding service information cannot be allocated. Applicable to functionality introduced
with the Rel8 feature as described in subclause 5.4.1.
ETSI
29
ETSI TS 129 214 V12.5.0 (2014-10)
NOTE 4: This value applies to applications for which the unsuccessful resource allocation notification is
required for their operation since subscription to this value impacts the resource allocation signalling
overhead towards the PCEF/BBERF.
INDICATION_OF_LIMITED_PCC_DEPLOYMENT (10)
Within a RAR, this value shall be used when the PCRF reports the limited PCC deployment (i.e. dynamically
allocated resources are not applicable) as specified at Annex K and Annex L in 3GPP TS 23.203 [2] to the AF.
In the AAR, this value indicates that the AF requests the PCRF to provide a notification for the limited PCC
deployment. Applicable to functionality introduced with the Rel8 feature as described in subclause 5.4.1.
USAGE_REPORT (11)
In the RA-Request (RAR), this value shall be used by the PCRF to report accumulated usage volume and/or time
of usage when the usage threshold provided by the AF has been reached.
In the AA-Request (AAR), this value indicates that the AF requests PCRF to report accumulated usage volume
and /or time of usage when it reaches the threshold.
Applicable to functionality introduced with the SponsoredConnectivity feature for volume usage reporting and
with SCTimeBased UM feature for time usage reporting as described in subclause 5.4.1.
ACCESS_NETWORK_INFO_REPORT (12)
In the RA-Request (RAR), this value shall be used by the PCRF to report access network information when the
PCRF receiving an Access Network Information report corresponding to the AF session from the PCEF/BBERF.
In the AA-Request (AAR), this value indicates that the AF requests PCRF to report one time access network
information when the PCRF receives the first Access Network Information report corresponding to the AF
session from the PCEF/BBERF after the AF request for the access network information. The required access
information is provided within the Required-Access-Info AVP. Applicable to functionality introduced with the
NetLoc feature as described in subclause 5.4.1.
The Specific-Action AVP with this value indicates a one time specific action.
INDICATION_OF_RECOVERY_FROM_LIMITED_PCC_DEPLOYMENT (13)
Within a RAR, this value shall be used when the PCRF reports the recovery from limited PCC deployment (i.e.
the UE moves from the VPLMN to the HPLMN as specified at Annex K in 3GPP TS 23.203 [2]) to the AF. In
the AAR, this value indicates that the AF requests the PCRF to provide a notification for the recovery from
limited PCC deployment. Applicable to functionality introduced with the Rel8 feature as described in subclause
5.4.1.
NOTE 5: This value is optional and only applicable to the scenario where PCC is deployed in the HPLMN but not
in the VPLMN and dynamic policy provisioning only occurs in the home routed roaming cases if no
BBERF is employed.
INDICATION_OF_ACCESS_NETWORK_INFO_REPORTING_FAILURE (14)
In the RAR, this value shall be used when the PCRF reports the access network information reporting failure.
When applicable, the NetLoc-Access-Support AVP may be provided as well to indicate the reason for the access
network information reporting failure. This specific action does not require to be provisioned by the AF.
Applicable to functionality introduced with the NetLoc feature as described in subclause 5.4.1.
5.3.14
Max-Requested-Bandwidth-DL AVP
The Max-Requested-Bandwidth-DL AVP (AVP code 515) is of type Unsigned32, and it indicates the maximum
bandwidth in bits per second for a downlink IP flow. The bandwidth contains all the overhead coming from the IP-layer
and the layers above, e.g. IP, UDP, RTP and RTP payload.
When provided in an AA-Request, it indicates the maximum requested bandwidth. When provided in an AA-Answer, it
indicates the maximum bandwidth acceptable by PCRF.
ETSI
5.3.15
30
ETSI TS 129 214 V12.5.0 (2014-10)
Max-Requested-Bandwidth-UL AVP
The Max Bandwidth-UL AVP (AVP code 516) is of type Unsigned32, and it indicates the maximum requested
bandwidth in bits per second for an uplink IP flow. The bandwidth contains all the overhead coming from the IP-layer
and the layers above, e.g. IP, UDP, RTP and RTP payload.
When provided in an AA-Request, it indicates the maximum requested bandwidth. When provided in an AA-Answer, it
indicates the maximum bandwidth acceptable by PCRF.
5.3.16
Media-Component-Description AVP
The Media-Component-Description AVP (AVP code 517) is of type Grouped, and it contains service information for a
single media component within an AF session or the AF signalling information. The service information may be based
on the SDI exchanged between the AF and the AF session client in the UE. The information may be used by the PCRF
to determine authorized QoS and IP flow classifiers for bearer authorization and PCC rule selection.
Within one Diameter message, a single IP flow shall not be described by more than one Media-Component-Description
AVP.
Bandwidth information and Flow-Status information provided within the Media-Component-Description AVP applies
to all those IP flows within the media component, for which no corresponding information is being provided within
Media-Sub-Component AVP(s).
If a Media-Component-Description AVP is not supplied by the AF, or if optional AVP(s) within a Media-ComponentDescription AVP are omitted, but corresponding information has been provided in previous Diameter messages, the
previous information for the corresponding IP flow(s) remains valid.
All IP flows within a Media-Component-Description AVP are permanently disabled by supplying a Flow Status AVP
with value 'REMOVED'. The server may delete corresponding filters and state information.
Reservation-Priority provided within the Media-Component-Description AVP in the request from the AF applies to all
those IP flows within the media component and describes the relative importance of the IP flow as compared to other IP
flows. The PCRF may use this value to implement priority based admission. If the Reservation-Priority AVP is not
specified the IP flow priority is DEFAULT (0).
Each Media-Component-Description AVP shall contain either zero, or one, or two Codec-Data AVPs. In the case of
conflicts, information contained in other AVPs either within this Media-Component-Description AVP, or within the
corresponding Media-Component-Description AVP in a previous message, shall take precedence over information
within the Codec-Data AVP(s). The AF shall provision all the available information in other applicable AVPs in
addition to the information in the Codec-Data AVP, if such other AVPs are specified.
If the SDP offer-answer procedures of IETF RFC 3264 [18] are applicable for the session negotiation between the two
ends taking part in the communication (e.g. for IMS), the following applies:
-
The AF shall provision information derived from an SDP answer and shall also provision information derived
from the corresponding SDP offer.
If the Media-Component-Description AVP contains two Codec-Data AVPs, one of them shall represent an SDP
offer and the other one the corresponding SDP answer.
If the Media-Component-Description AVP contains one Codec-Data AVP, and this AVP represents an SDP
offer, the AF shall provision the corresponding SDP answer information in a Codec-Data AVP within a
subsequent Rx message.
NOTE:
Some SDP parameters for the same codec in the SDP offer and answer are independent of each other and
refer to IP flows in opposite directions, for instance some MIME parameters conveyed within 'a=fmtp'
SDP lines and the packetization time within the 'a=ptime' line. Other parameters within the SDP answer
take precedence over corresponding parameters within the SDP offer.
If SDP is applied without using the offer-answer procedures, zero or one Codec-Data AVP shall be provisioned.
The PCRF may provide the Media-Component-Description AVP(s) within the Acceptable-Service-Info AVP in the
AA-Answer command if the service information received from the AF is rejected. For this usage, the Media-
ETSI
31
ETSI TS 129 214 V12.5.0 (2014-10)
Component-Description AVP shall only include the appropriate Media-Component-Number AVP and the MaxRequested-Bandwidth-UL and/or Max-Requested-Bandwidth-DL AVPs indicating the maximum acceptable bandwidth.
AVP format:
Media-Component-Description ::= < AVP Header: 517 >
{ Media-Component-Number } ; Ordinal number of the media comp.
*[ Media-Sub-Component ]
; Set of flows for one flow identifier
[ AF-Application-Identifier ]
[ Media-Type ]
[ Max-Requested-Bandwidth-UL ]
[ Max-Requested-Bandwidth-DL ]
[ Min-Requested-Bandwidth-UL ]
[ Min-Requested-Bandwidth-DL ]
[ Flow-Status ]
[ Reservation-Priority ]
[ RS-Bandwidth ]
[ RR-Bandwidth ]
*[ Codec-Data ]
5.3.17
Media-Component-Number AVP
The Media-Component-Number AVP (AVP code 518) is of type Unsigned32, and it contains the ordinal number of the
media component, assigned according to the rules in Annex B.
When this AVP refers to AF signalling, this is indicated by using the value 0 according to the rules in Annex B.
5.3.18
Media-Sub-Component AVP
The Media-Sub-Component AVP (AVP code 519) is of type Grouped, and it contains the requested bitrate and filters
for the set of IP flows identified by their common Flow-Identifier. The Flow-Identifier is defined in Annex B.
Possible Bandwidth information and Flow-Status information provided within the Media-Sub-Component AVP takes
precedence over information within the encapsulating Media Component Description AVP. If a Media-SubComponent- AVP is not supplied, or if optional AVP(s) within a Media-Sub-Component AVP are omitted, but
corresponding information has been provided in previous Diameter messages, the previous information for the
corresponding IP flow(s) remains valid, unless new information is provided within the encapsulating
Media-Component-Description AVP. If Flow-Description AVP(s) are supplied, they replace all previous
Flow-Description AVP(s), even if a new Flow-Description AVP has the opposite direction as the previous
Flow-Description AVP.
The AF-Signalling-Protocol AVP may be included only if the Flow-Usage AVP has a value of "AF_SIGNALLING".
All IP flows within a Media-Sub-Component- AVP are permanently disabled by supplying a Flow Status AVP with
value 'REMOVED'. The server may delete corresponding filters and state information.
AVP format:
Media-Sub-Component ::= < AVP Header: 519 >
{ Flow-Number }
; Ordinal number of the IP flow
0*2[ Flow-Description ]
; UL and/or DL
[ Flow-Status ]
[ Flow-Usage ]
[ AF-Signalling-Protocol ]
*[ AVP ]
5.3.19
Media-Type AVP
The Media-Type AVP (AVP code 520) is of type Enumerated, and it determines the media type of a session
component. The media types indicate the type of media in the same way as the SDP media types with the same names
defined in RFC 4566 [13]. The following values are defined:
-
AUDIO (0)
VIDEO (1)
ETSI
DATA (2)
APPLICATION (3)
CONTROL (4)
TEXT (5)
MESSAGE (6)
OTHER (0xFFFFFFFF)
5.3.20
32
ETSI TS 129 214 V12.5.0 (2014-10)
RR-Bandwidth AVP
The RR-Bandwidth AVP (AVP code 521) is of type Unsigned32, and it indicates the maximum required bandwidth in
bits per second for RTCP receiver reports within the session component, as specified in RFC 3556 [11]. The bandwidth
contains all the overhead coming from the IP-layer and the layers above, i.e. IP, UDP and RTCP.
5.3.21
RS-Bandwidth AVP
The RS-Bandwidth AVP (AVP code 522) is of type Unsigned32, and it indicates the maximum required bandwidth in
bits per second for RTCP sender reports within the session component, as specified in RFC 3556 [11]. The bandwidth
contains all the overhead coming from the IP-layer and the layers above, i.e. IP, UDP and RTCP.
5.3.22
SIP-Forking-Indication AVP
The SIP-Forking-Indication AVP (AVP code 523) is of type Enumerated, and describes if several SIP dialogues are
related to one Diameter session:
SINGLE_DIALOGUE (0)
This value is used to indicate that the Diameter session relates to a single SIP dialogue.
This is the default value applicable if the AVP is omitted.
SEVERAL_DIALOGUES (1)
This value is used to indicate that the Diameter session relates to several SIP dialogues.
5.3.23
Service-URN AVP
The Service-URN AVP (AVP code 525) is of type OctetString, and it indicates that an AF session is used for
emergency traffic.
It contains values of the service URN including subservices, as defined in [21] or registered at IANA. The string
'urn:service:' in the beginning of the URN shall be omitted in the AVP and all subsequent text shall be included.
Examples of valid values of the AVP are 'sos', 'sos.fire', 'sos.police' and 'sos.ambulance'.
5.3.24
Acceptable-Service-Info AVP
The Acceptable-Service-Info AVP (AVP code 526) is of type Grouped, and contains the maximum bandwidth for an
AF session and/or for specific media components that will be authorized by the PCRF. The Max-Requested-BandwidthDL AVP and Max-Requested-Bandwidth-UL AVP directly within the Acceptable-Service-Info AVP indicate the
acceptable bandwidth for the entire AF session. The Max-Requested-Bandwidth-DL AVP and Max-RequestedBandwidth-UL AVP within a Media-Component-Description AVP included in the Acceptable-Service-Info AVP
indicate the acceptable bandwidth for the corresponding media component.
If the acceptable bandwidth applies to one or more media components, only the Media-Component-Description AVP
will be provided. If the acceptable bandwidth applies to the whole AF session, only the Max-Requested-Bandwidth-DL
AVP and Max-Requested-Bandwidth-UL AVP will be included.
Acceptable-Service-Info::= < AVP Header: 526 >
*[ Media-Component-Description]
ETSI
33
ETSI TS 129 214 V12.5.0 (2014-10)
*[ AVP ]
5.3.25
Service-Info-Status-AVP
The Service-Info-Status AVP (AVP code 527) is of type Enumerated, and indicates the status of the service information
that the AF is providing to the PCRF. If the Service-Info-Status AVP is not provided in the AA request, the value
FINAL SERVICE INFORMATION shall be assumed.
FINAL SERVICE INFORMATION (0)
This value is used to indicate that the service has been fully negotiated between the two ends and service
information provided is the result of that negotiation.
PRELIMINARY SERVICE INFORMATION (1)
This value is used to indicate that the service information that the AF has provided to the PCRF is
preliminary and needs to be further negotiated between the two ends (e.g. for IMS when the service
information is sent based on the SDP offer).
5.3.26
AF-Signalling-Protocol-AVP
The AF-Signalling-Protocol AVP (AVP code 529) is of type Enumerated, and indicates the protocol used for signalling
between the UE and the AF. If the AF-Signalling-Protocol AVP is not provided in the AA-Request, the value
NO_INFORMATION shall be assumed.
NO_INFORMATION (0)
This value is used to indicate that no information about the AF signalling protocol is being provided.
SIP (1)
This value is used to indicate that the signalling protocol is Session Initiation Protocol.
5.3.27
Sponsored-Connectivity-Data AVP
The Sponsored-Connectivity-Data AVP (AVP code 530) is of type Grouped, and contains the data associated with the
sponsored data connectivity.
The Sponsor-Identity AVP identifies the sponsor. It shall be included by the AF in the Sponsored-Connectivity-Data
AVP.
The Application-Service-Provider-Identity AVP identifies the application service provider. It shall be included by the
AF in the Sponsored-Connectivity-Data AVP.
The Granted-Service-Unit AVP shall be used by the AF to provide usage threshold to the PCRF if the volume and/or
time of traffic allowed during the sponsored data connectivity is to be monitored.
The Used-Service-Unit AVP shall be used by the PCRF to provide the measured usage to the AF. Reporting shall be
done, as requested by the AF, in CC-Total-Octets, CC-Input-Octets, CC-Output-Octets or CC-Time of the UsedService-Unit AVP.
AVP format:
Sponsored-Connectivity-Data::=
[
[
[
[
*[
5.3.28
< AVP Header: 530 >

Sponsor-Identity ]
Application-Service-Provider-Identity ]
Granted-Service-Unit ]
Used-Service-Unit ]
AVP ]
Sponsor-Identity AVP
The Sponsor-Identity AVP (AVP code 531) is of type UTF8String and is used for sponsored data connectivity purposes
as an identifier of the sponsor.
ETSI
5.3.29
34
ETSI TS 129 214 V12.5.0 (2014-10)
Application-Service-Provider-Identity AVP
The Application-Service-Provider-Identity AVP (AVP code 532) is of type UTF8String and is used for sponsored data
connectivity purposes as an identifier of the application service provider.
5.3.30
MPS-Identifier AVP
The MPS-Identifier AVP (AVP code 528) is of type OctetString, and it indicates that an AF session relates to an MPS
session. It contains the national variant for MPS service name (e.g., NGN GETS).
5.3.31
Rx-Request-Type AVP
The Rx-Request-Type AVP (AVP code 533) is of type Enumerated, and contains the reason for sending the AARequest message.
INITIAL_REQUEST (0)
An initial request is used to initiate an Rx session and contains information that is relevant to initiation.
UPDATE_REQUEST (1)
An update request is used to update an existing Rx session.
PCSCF_RESTORATION (2)
A P-CSCF Restoration is requested.
5.3.32
Min-Requested-Bandwidth-DL AVP
The Min-Requested-Bandwidth-DL AVP (AVP code 534) is of type Unsigned32, and it indicates the minimum
requested bandwidth in bits per second for a downlink IP flow. The bandwidth contains all the overhead coming from
the IP-layer and the layers above, e.g. IP, TCP, UDP, HTTP, RTP and RTP payload.
When provided in an AA-Request, it indicates the minimum requested bandwidth.
5.3.33
Min-Requested-Bandwidth-UL AVP
The Min-Requested-Bandwidth-UL AVP (AVP code 535) is of type Unsigned32, and it indicates the minimum
requested bandwidth in bits per second for an uplink IP flow. The bandwidth contains all the overhead coming from the
IP-layer and the layers above, e.g. IP, TCP, UDP, HTTP, RTP and RTP payload.
When provided in an AA-Request, it indicates the minimum requested bandwidth.
5.3.34
Required-Access-Info AVP
The Required-Access-Info AVP (AVP code 536) is of type Enumerated, and contains the access network information
required for that AF session.
USER_LOCATION (0)
Indicates that the user location information shall be reported, the PCRF shall report the user location
information within the 3GPP-User-Location-Info AVP (if available), the serving PLMN identifier within the
3GPP-SGSN-MCC-MNC AVP (if available), the user location information within the TWAN-Identifier (if
available) and User-Location-Info-Time AVP (if available).
MS_TIME_ZONE (1)
ETSI
35
ETSI TS 129 214 V12.5.0 (2014-10)
Indicates that the user timezone information shall be reported, the PCRF shall report the user timezone
information within the 3GPP-MS-TimeZone AVP.
5.3.35
IP-Domain-Id AVP
The IP-Domain-Id AVP (AVP code 537) is of type (OctetString), and indicates the domain information which assists
session binding.
5.3.36
GCS-Identifier AVP
The GCS-Identifier AVP (AVP code 538) is of type OctetString, and it indicates that an AF session relates to a Group
Communication session that requires prioritization.The values that identify the Group Communication session are not
specified.
5.4
Rx re-used AVPs
Table 5.4.1 lists the Diameter AVPs re-used by the Rx reference point from existing Diameter Applications, including a
reference to their respective specifications and when needed, a short description of their usage within the Rx reference
point. Other AVPs from existing Diameter Applications, except for the AVPs from Diameter Base Protocol, do not
need to be supported. The AVPs from Diameter Base Protocol are not included in table 5.4.1, but they are re-used for
the Rx protocol. Unless otherwise stated, re-used AVPs shall maintain their "M", "P" and "V" flag settings. Where
3GPP Radius VSAs are re-used, unless otherwise stated, they shall be translated to Diameter AVPs as described in RFC
4005 [12] with the exception that the "M" flag shall be set and the "P" flag may be set.
ETSI
36
ETSI TS 129 214 V12.5.0 (2014-10)
Table 5.4.1: Rx re-used Diameter AVPs

Attribute Name
Reference
Comments
Indicates the offset between universal time and

local time in steps of 15 minutes of where the MS
currently resides.
For GPRS the MCC and the MNC of the SGSN.
3GPP-SGSN-MCC-MNC 3GPP TS 29.061 [11]
For 3GPP EPS the MCC and the MNC provided by
the serving gateway (SGW).
Indicates details of where the UE is currently
3GPP-User-Location-Info 3GPP TS 29.061 [11]
located (e.g. SAI or CGI),Coding shall be done as
defined in 3GPP TS 29.274 [33]
Indicates the time the UE was last known to be in
the location which is reported during bearer
User-Location-Info-Time 3GPP TS 29.212 [8]
deactivation or IP-CAN session termination
procedure.
Called-Station-Id
RFC 4005 [12]
The PDN the user is connected to.
The action applied by the PCEF when the user"s
Final-Unit-Action
RFC 4006 [14]
account cannot cover the service cost.
The valid routable Ipv4 address that is applicable
for the IP Flows towards the UE at the PCEF. The
PCRF shall use this address to identify the correct
IP-CAN session (session binding). For example,
Framed-IP-Address
RFC 4005 [12]
the IP address may actually be that of the network
interface of a NAT device between the UE and the
GW. The values
0xFFFFFFFF and 0xFFFFFFFE are not applicable
as described in RFC 4005 [12].
A valid full Ipv6 address that is applicable to an IP
flow or IP flows towards the UE at the PCEF. The
PCRF shall use this address to identify the correct
IP-CAN session (session binding, refer to 3GPP
TS 29.213 [9]). For example, the IP address may
actually be that of the network interface of a NAT
Framed-Ipv6-Prefix
RFC 4005 [12]
device between the UE and the GW.
The encoding of the value within this Octet String
type AVP shall be as defined in RFC 3162 [20],
clause 2.3. The 'Reserved', 'Prefix-Length' and
'Prefix' fields shall be included in this order. The AF
shall set the 'Prefix Length' to 128 and encode the
Ipv6 address of the UE within the 'Prefix' field.
The volume and/or time thresholds for sponsored
data connectivity. Only CC-Total-Octets, one of the
Granted-Service-Unit
CC-Input-Octets and CC-Output-Octets, or CCRFC 4006 [14]
(NOTE 3)
Time AVPs are reused.
This AVP shall have the "M" bit cleared.
IP-CAN-Type
3GPP TS 29.212 [8]
IP-CAN type of the user.
IETF draft-ietf-dime-ovli- Contains the necessary information to convey an
OC-OLR
02 [35]
overload report
IETF draft-ietf-dime-ovli- Defines the support for the Diameter overload
OC-Supported-Features
02 [35]
indication conveyence by the sending node
RAN-NAS-ReleaseIndicates RAN and/or NAS release cause code
3GPP TS 29.212 [8]
Cause
information.
Indicates the level of support for NetLoc
NetLoc-Access-Support 3GPP TS 29.212 [8]
procedures provided by the current access
network.
Indicate which Radio Access Technology is
RAT-Type
3GPP TS 29.212[8]
currently serving the UE.
The vendor-id shall be set to ETSI (13019) [15].
The support of this AVP shall be advertised in the
Reservation-Priority
TS 183.017 [15]
capabilities exchange mechanisms (CER/CEA) by
including the ETSI parameter in the SupportedVendor-Id AVP.
The identification of the subscription (IMSI,
Subscription-Id
RFC 4006 [14]
MSISDN, etc.)
3GPP-MS-TimeZone
Applicability
(notes 1, 2)
NetLoc
3GPP TS 29.061 [11]
ETSI
NetLoc
NetLoc
NetLoc
Rel8
Rel8
SponsoredCo
nnectivity,
SCTimeBase
dUM
NetLoc-RANNAS-Cause
NetLoc
Rel8
Attribute Name
Supported-Features
Used-Service-Unit
(NOTE 3)
TWAN-Identifier
37
Reference
3GPP TS 29.229 [25]
RFC 4006 [14]
3GPP TS 29.061 [34]
ETSI TS 129 214 V12.5.0 (2014-10)
Comments
If present, this AVP informs the destination host
about the features that the origin host requires to
successfully complete this command exchange.
The measured volume and/or time for sponsored
data connectivity. Only CC-Total-Octets, one of the
CC-Input-Octets and CC-Output-Octets, or CCTime AVPs are reused.
Indicates the UE location in a Trusted WLAN
Access Network.
Applicability
(notes 1, 2)
Rel8
SponsoredCo
nnectivity
SCTimeBase
dUM
NetlocTrustedWLAN
NOTE 1: AVPs marked with 'Rel8' are applicable as described in clause 5.4.1.
NOTE 2: AVPs marked with 'SponsoredConnectivity' are applicable for sponsored data connectivity.
NOTE 3: Volume Usage monitoring control functionality is applicable for SponsoredConnectivity supported feature.
Time Based Usage monitoring control is applicable for SCTimeBasedUM supported feature.
5.4.1
Use of the Supported-Features AVP on the Rx reference point
The Supported-Features AVP is used during session establishment to inform the destination host about the required and
optional features that the origin host supports. The client shall, in the first request of a Diameter session indicate the set
of supported features. The server shall, in the first answer within the Diameter session indicate the set of features that it
has in common with the client and that the server shall support within the same Diameter session. Any further command
messages shall always be compliant with the list of supported features indicated in the Supported-Features AVPs during
session establishment. Features that are not advertised as supported shall not be used to construct the command
messages for that Diameter session. Unless otherwise stated, the use of the Supported-Features AVP on the Rx
reference point shall be compliant with the requirements for dynamic discovery of supported features and associated
error handling on the Cx reference point as defined in clause 7.2.1 of 3GPP TS 29.229 [25].
The base functionality for the Rx reference point is the 3GPP Rel-7 standard and a feature is an extension to that
functionality. If the origin host does not support any features beyond the base functionality, the Supported-Features
AVP may be absent from the Rx commands. As defined in clause 7.1.1 of 3GPP TS 29.229 [25], when extending the
application by adding new AVPs for a feature, the new AVPs shall have the M bit cleared and the AVP shall not be
defined mandatory in the command ABNF.
As defined in 3GPP TS 29.229 [25], the Supported-Features AVP is of type grouped and contains the Vendor-Id,
Feature-List-ID and Feature-List AVPs. On the Rx reference point, the Supported-Features AVP is used to identify
features that have been defined by 3GPP and hence, for features defined in this document, the Vendor-Id AVP shall
contain the vendor ID of 3GPP (10415). If there are multiple feature lists defined for the Rx reference point, the
Feature-List-ID AVP shall differentiate those lists from one another.
On receiving an initial request application message, the destination host shall act as defined in clause 7.2.1 of 3GPP TS
29.229 [25]. The following exceptions apply to the initial AAR/AAA command pair:
-
If the AF supporting post-Rel-7 Rx functionality is able to interoperate with a PCRF supporting Rel-7, the AAR
shall include the features supported by the AF within Supported-Features AVP(s) with the "M" bit cleared.
Otherwise, the AAR shall include the supported features within the Supported-Features AVP(s) with the M-bit
set.
NOTE 1: One instance of Supported-Features AVP is needed per Feature-List-ID.

-
If the AAR command does not contain any Supported-Features AVP(s) and the PCRF supports Rel-7 Rx
functionality, the AAA command shall not include the Supported-Features AVP. In this case, both AF and PCRF
shall behave as specified in the Rel-7 version of this document.
If the AAR command contains the Supported-Features AVP(s), the PCRF shall include the Supported-Features
AVP(s) in the AAA command, with the "M" bit cleared, indicating only the features that both the PCRF and AF
support.
ETSI
38
ETSI TS 129 214 V12.5.0 (2014-10)
NOTE 2: The client will always declare all features that are supported according to table 5.4.1.1. When more than
one feature identifying a release is supported by both AF and PCRF, the AF will work according to the
latest common supported release.
Once the PCRF and AF have negotiated the set of supported features during session establishment, the set of common
features shall be used during the lifetime of the Diameter session.
The table below defines the features applicable to the Rx interfaces for the feature list with a Feature-List-ID of 1.
Table 5.4.1.1: Features of Feature-List-ID 1 used in Rx
Feature
bit
0
Feature
M/O
Rel8
Description
This feature indicates the support of the base 3GPP Rel-8 functionality,
including the AVPs and corresponding procedures supported by the base
3GPP Rel-7 Rx standard, but excluding those features represented by
separate feature bits. AVPs introduced with this feature are marked with
'Rel8' in Table 5.4.1
1
Rel9
M
including the AVPs and corresponding procedures supported by the Rel8
feature bit, but excluding those features represented by separate feature
bits.
2
ProvAFsignalFlow
O
This indicates support for the feature of provisioning of AF signalling flow
information as described in subclause 4.4.5a. If the PCRF supports this
feature the AF may provision AF signalling flow information.
NOTE: This feature is used by the IMS Restoration Procedures to
provide to the PDN-Gateway the address of the P-CSCF
selected by the UE, refer to 3GPP TS 23.380 [28].
3
O
This feature indicates support for sponsored data connectivity feature. If
the PCRF supports this feature, the AF may provide sponsored data
connectivity to the subscriber.
4
Rel10
M
including the AVPs and corresponding procedures supported by the Rel8
and Rel9 feature bit, but excluding those features represented by separate
feature bits. AVPs introduced with this feature are marked with 'Rel10' in
table 5.3.1.
5
NetLoc
O
This feature indicates the support of the Access Network Information
Reporting.
6
ExtendedFilter
O
This feature indicates the support for the local (i.e. UE) address and mask
being present in filters signalled between network and UE.
7
SCTimeBasedUM
O
This feature indicates support for sponsored data connectivity feature with
time-based usage monitoring control required. If the PCRF supports this
feature, the AF may provide time threshold for the usage monitoring
control.
8
Netloc-Trusted-WLAN
O
This feature indicates the support for the Trusted WLAN access.It requires
that NetLoc feature is also supported.
9
NetLoc-RAN-NASO
This feature indicates the support for the detailed RAN and/or NAS release
Cause
cause code information from the access network. It requires that the
NetLoc feature is also supported.
10
GroupComService
O
This feature indicates the support of Group Communication services as
described in 3GPP TS 23.468 [36] for unicast services.
Feature bit: The order number of the bit within the Feature-List AVP where the least significant bit is assigned number
'0'.
Feature: A short name that can be used to refer to the bit and to the feature, e.g. 'EPS'.
M/O: Defines if the implementation of the feature is mandatory ('M') or optional ('O').
Description: A clear textual description of the feature.
5.5
Rx specific Experimental-Result-Code AVP values
RFC 3588 [10] specifies the Experimental-Result AVP containing Vendor-ID AVP and Experimental-Result-Code
AVP. The Experimental-Result-Code AVP (AVP Code 298) is of type Unsigned32 and contains a vendor-assigned
value representing the result of processing a request. The Vendor-ID AVP shall be set to 3GPP (10415).
Specific values of the Rx specific Experimental-Result-Code AVP are:
ETSI
39
ETSI TS 129 214 V12.5.0 (2014-10)
INVALID_SERVICE_INFORMATION (5061)
The PCRF rejects new or modified service information the service information provided by the AF is invalid
or insufficient for the server to perform the requested action.
FILTER_RESTRICTIONS (5062)
The PCRF rejects new or modified service information because the Flow-Description AVP(s) cannot be
handled by the server because restrictions defined in clause 5.3.7 are not observed.
REQUESTED_SERVICE_NOT_AUTHORIZED (5063)
The PCRF rejects new or modified service information because the requested service, as described by the
service information provided by the AF, is not consistent with either the related subscription information,
operator defined policy rules and/or the supported features in the IP-CAN network.
DUPLICATED_AF_SESSION (5064)
The PCRF rejects a new Rx session setup because the new Rx session relates to an AF session with another
related active Rx session, e.g. if the AF provided the same AF charging identifier for this new Rx session that
is already in use for the other ongoing Rx session.
IP-CAN_SESSION_NOT_AVAILABLE (5065)
The PCRF rejects a new Rx session setup when it fails to associate the described service IP flows within the
session information received from the AF to an existing IP-CAN session.
UNAUTHORIZED_NON_EMERGENCY_SESSION (5066)
The PCRF rejects a new Rx session setup because the session binding function associated a non-Emergency
IMS session to an IP-CAN session established to an Emergency APN.
UNAUTHORIZED_SPONSORED_DATA_CONNECTIVITY (5067)
The PCRF rejects a new Rx session setup because the PCRF can"t authorize the sponsored data connectivity
based on the sponsored data connectivity profile or the operator policy (e.g. the sponsored data connectivity
not authorized in the roaming case).
TEMPORARY_NETWORK_FAILURE (5068)
The PCRF rejects new or modified service information because there is a temporary failure in the access
network (e.g. the SGW has failed).
5.6
Rx messages
Existing Diameter command codes from the Diameter base protocol RFC 3588 [10] and the NASREQ Diameter
application (RFC 4005 [12]) are used with the Rx specific AVPs. An Rx specific Auth-Application id is used together
with the command code to identify the Rx messages.
NOTE 1: The notion of NAS (Network Access Server) is not used here, NASREQ is just used for protocol
purposes, not for its functional meaning.
NOTE 2: Some of the AVPs included in the messages formats below are in bold to highlight that these AVPs are
used by this specific protocol and do not belong to the original Diameter Base Protocol RFC 3588 [10].
NOTE3: Multiple instances of the Subscription-Id AVP in the AAR or RAR command correspond to multiple
types of identifier for the same subscriber, for example IMSI and MSISDN.
5.6.1
AA-Request (AAR) command
The AAR command, indicated by the Command-Code field set to 265 and the "R" bit set in the Command Flags field,
is sent by an AF to the PCRF in order to provide it with the Session Information.
Message Format:
ETSI

<AA-Request> ::= <
<
{
{
{
{
[
[
[
*[
[
[
[
*[
*[
[
*[
[
[
[
[
[
[
[
[
[
*[
[
*[
*[
*[
5.6.2
40
ETSI TS 129 214 V12.5.0 (2014-10)
Diameter Header: 265, REQ, PXY >

Session-Id >
Auth-Application-Id }
Origin-Host }
Origin-Realm }
Destination-Realm }
Destination-Host ]
IP-Domain-Id ]
AF-Application-Identifier ]
Media-Component-Description ]
Service-Info-Status ]
AF-Charging-Identifier ]
SIP-Forking-Indication ]
Specific-Action ]
Subscription-Id ]
OC-Supported-Features ]
Supported-Features ]
Reservation-Priority ]
Framed-IP-Address ]
Framed-Ipv6-Prefix ]
Called-Station-Id ]
Service-URN ]
Sponsored-Connectivity-Data ]
MPS-Identifier ]
GCS-Identifier ]
Rx-Request-Type ]
Required-Access-Info ]
Origin-State-Id ]
Proxy-Info ]
Route-Record ]
AVP ]
AA-Answer (AAA) command
The AAA command, indicated by the Command-Code field set to 265 and the "R" bit cleared in the Command Flags
field, is sent by the PCRF to the AF in response to the AAR command.
Message Format:
<AA-Answer> ::= <
<
{
{
{
[
[
[
*[
[
[
[
[
[
*[
[
[
*[
*[
[
[
*[
[
*[
[
[
*[
*[
5.6.3
Diameter Header: 265, PXY >

Session-Id >
Origin-Host }
Origin-Realm }
Result-Code ]
Experimental-Result ]
Auth-Session-State ]
Access-Network-Charging-Identifier ]
Access-Network-Charging-Address ]
Acceptable-Service-Info ]
IP-CAN-Type ]
NetLoc-Access-Support ]
RAT-Type ]
Flows ]
OC-OLR ]
Supported-Features ]
Class ]
Error-Message ]
Error-Reporting-Host ]
Failed-AVP ]
Origin-State-Id ]
Redirect-Host ]
Redirect-Host-Usage ]
Redirect-Max-Cache-Time ]
Proxy-Info ]
AVP ]
Re-Auth-Request (RAR) command
The RAR command, indicated by the Command-Code field set to 258 and the "R" bit set in the Command Flags field, is
sent by the PCRF to the AF in order to indicate an Rx specific action.
Message Format:
<RA-Request> ::= < Diameter Header: 258, REQ, PXY >
ETSI

<
{
{
{
{
{
*{
[
*[
[
*[
*[
[
[
[
[
[
[
[
[
[
[
[
[
*[
*[
*[
*[
5.6.4
41
ETSI TS 129 214 V12.5.0 (2014-10)
Session-Id >
Origin-Host }
Origin-Realm }
Destination-Realm }
Destination-Host }
Specific-Action }
Access-Network-Charging-Identifier ]
Access-Network-Charging-Address ]
Flows ]
Subscription-Id ]
Abort-Cause ]
IP-CAN-Type ]
NetLoc-Access-Support ]
RAT-Type ]
3GPP-User-Location-Info ]
User-Location-Info-Time ]
3GPP-MS-TimeZone ]
RAN-NAS-Release-Cause ]
3GPP-SGSN-MCC-MNC ]
TWAN-Identifier ]
Origin-State-Id ]
Class ]
Proxy-Info ]
Route-Record ]
AVP ]
Re-Auth-Answer (RAA) command
The RAA command, indicated by the Command-Code field set to 258 and the "R" bit cleared in the Command Flags
field, is sent by the AF to the PCRF in response to the RAR command.
Message Format:
<RA-Answer> ::= <
<
{
{
[
[
[
[
*[
[
[
*[
[
[
*[
[
[
*[
*[
*[
5.6.5

Session-Id >
Origin-Host }
Origin-Realm }
Result-Code ]
Experimental-Result ]
OC-OLR ]
Media-Component-Description ]
Service-URN ]
Origin-State-Id ]
Class ]
Error-Message ]
Redirect-Host ]
Failed-AVP ]
Proxy-Info ]
AVP ]
Session-Termination-Request (STR) command
The STR command, indicated by the Command-Code field set to 275 and the "R" bit set in the Command Flags field, is
sent by the AF to inform the PCRF that an established session shall be terminated.
Message Format:
<ST-Request> ::= <
<
{
{
{
{
{
[
[
*[
*[
[
Diameter Header: 275, REQ, PXY >

Session-Id >
Origin-Host }
Origin-Realm }
Destination-Realm }
Termination-Cause }
Destination-Host ]
Required-Access-Info ]
Class ]
Origin-State-Id ]
ETSI
42
ETSI TS 129 214 V12.5.0 (2014-10)
*[ Proxy-Info ]
*[ Route-Record ]
*[ AVP ]
5.6.6
Session-Termination-Answer (STA) command
The STA command, indicated by the Command-Code field set to 275 and the "R" bit cleared in the Command Flags
field, is sent by the PCRF to the AF in response to the STR command.
Message Format:
<ST-Answer> ::= <
<
{
{
[
[
[
[
[
[
[
[
[
[
[
[
[
[
[
*[
*[
[
[
*[
*[
5.6.7

Session-Id >
Origin-Host }
Origin-Realm }
Result-Code ]
Error-Message ]
OC-OLR ]
Failed-AVP ]
Origin-State-Id ]
3GPP-User-Location-Info ]
User-Location-Info-Time ]
3GPP-MS-TimeZone ]
RAN-NAS-Release-Cause ]
3GPP-SGSN-MCC-MNC ]
TWAN-Identifier ]
Netloc-Access-Support ]
Class ]
Redirect-Host ]
Proxy-Info ]
AVP ]
Abort-Session-Request (ASR) command
The ASR command, indicated by the Command-Code field set to 274 and the "R" bit set in the Command Flags field, is
sent by the PCRF to inform the AF that bearer for the established session is no longer available.
Message Format:
<AS-Request> ::= < Diameter Header: 274, REQ, PXY >
< Session-Id >
{ Origin-Host }
{ Origin-Realm }
{ Destination-Realm }
{ Destination-Host }
{ Auth-Application-Id }
[ OC-Supported-Features ]
{ Abort-Cause }
[ Origin-State-Id ]
*[ Proxy-Info ]
*[ Route-Record ]
*[ AVP ]
5.6.8
Abort-Session-Answer (ASA) command
The ASA command, indicated by the Command-Code field set to 274 and the "R" bit cleared in the Command Flags
field, is sent by the AF to the PCRF in response to the ASR command.
Message Format:
<AS-Answer> ::= < Diameter Header: 274, PXY >
< Session-Id >
{ Origin-Host }
{ Origin-Realm }
[ Result-Code ]
[ OC-Supported-Features ]
[ OC-OLR ]
[ Origin-State-Id ]
[ Error-Message ]
[ Error-Reporting-Host ]
ETSI

*[
*[
[
[
*[
*[
43
Failed-AVP ]
Redirect-Host ]
Proxy-Info ]
AVP ]
ETSI
ETSI TS 129 214 V12.5.0 (2014-10)
44
ETSI TS 129 214 V12.5.0 (2014-10)
Annex A (normative):
IMS Related P-CSCF Procedures over Rx
A.1
Provision of Service Information at P-CSCF
The P-CSCF shall send service information to the PCRF upon every SIP message that includes an SDP answer payload
for the purpose of authorizing the IP flows and the QoS resources required for a negotiated IMS session, unless the SDP
payload only relates to a circuit-switched bearer (i.e. 'c=' line set to 'PSTN' and an 'm=' line set to 'PSTN', refer to 3GPP
TS 24.292 [26]). The service information shall be derived both from the SDP offer and the SDP answer. This ensures
that the PCRF receives proper information to perform media authorization for all possible IMS session set-up scenarios,
and that the PCRF is also capable of handling session modifications. The P-CSCF may include the Service-Info-Status
AVP with the value set to FINAL_SERVICE_INFORMATION.
Additionally, the P-CSCF may send service information to the PCRF when receiving a SIP message that includes an
SDP offer payload for the purpose of performing an early bandwidth authorization check, or for enabling preauthorization for a UE terminated IMS session establishment or modification with UE initiated resource reservation, or
for the retrieval of network provided access network information (see subclause A.10.2). The P-CSCF shall send service
information to the PCRF when receiving a SIP message that includes an SDP offer payload when the IMS session is an
MPS session that requires priority treatment. For a UE terminated session the P-CSCF may send the service information
derived from the SDP offer when the SDP offer either does not include any preconditions information or includes
preconditions information indicating that the local preconditions (i.e. the preconditions related to the remote peer) are
already met. In this case, the P-CSCF shall derive the service information only from the SDP offer and shall include the
Service-Info-Status AVP with the value set to PRELIMINARY SERVICE INFORMATION.
NOTE:
For a UE terminated session setup, when the SDP offer either does not include any preconditions
information or includes preconditions information indicating that the local preconditions (i.e. the
preconditions related to the remote peer) are already met, the terminating UE can request a resource
modification prior to sending the SDP answer. Even if the IP address and port information in the session
information derived from the SDP offer can be insufficient for PCC rule authorization, the policy to
handle such UE initiated requests at the PCRF can take into account the fact that an IMS session
establishment is ongoing, for instance in deciding whether to authorize the request and in selecting an
appropriate charging key and a gating policy.
The P-CSCF shall derive Flow-Description AVP within the service information from the SDP as follows:
-
An uplink Flow-Description AVP shall be formed as follows: The destination address shall be taken from the
SDP information received by the P-CSCF in downlink direction, while the source IP address may be formed
from the address present in the SDP received by the P-CSCF in uplink direction (taking into account only the 64
bit prefix of the Ipv6 address) Source and destination ports shall be derived according to rules provided in 3GPP
TS 29.213 [9] subclause 6.2.
EXAMPLE 1:
Assuming UE A sends an SDP to UE B, the PCRF of UE B uses the address present in this SDP
for the destination address of UE B"s uplink Flow-Description AVP, while the PCRF of the UE A
uses the 64 bit prefix of the same address for the source address of UE A"s uplink
Flow-Description AVP. If the source address is not formed from the 64 bit prefix, the source
address shall be wildcarded.
A downlink Flow-Description AVP shall be formed as follows: The destination address shall be taken from the
SDP information received by the P-CSCF in uplink direction, while the source IP address may be formed (in
order to reduce the possibilities of bearer misuse) from the destination address in the SDP received by the PCSCF in downlink direction (taking into account only the 64 bit prefix of the Ipv6 address) Source and
destination ports shall be derived according to rules provided in 3GPP TS 29.213 [9] subclause 6.2.
ETSI
EXAMPLE 2:
45
ETSI TS 129 214 V12.5.0 (2014-10)
Assuming UE A sends an SDP to UE B, the PCRF of UE A uses the address present in this SDP
for the destination address of UE A"s downlink Flow-Description AVP, while the PCRF of UE B
uses the 64 bit prefix of the same address for the source address of UE B"s downlink
Flow-Description AVP. If the source address is not formed from the 64 bit prefix, the source
address shall be wildcarded.
The P-CSCF shall derive the bandwidth information within the service information, from the 'b=AS' SDP parameter, as
detailed in 3GPP TS 29.213 [9] subclause 6.2. For the possibly associated RTCP IP flows, the P-CSCF shall use the
SDP 'b=RR' and 'b=RS' parameters, if present, as specified in 3GPP TS 29.213 [9] subclause 6.2. The 'b=AS', 'b=RR'
and 'b=RS' parameters in the SDP contain all the overhead coming from the IP-layer and the layers above, e.g. IP, UDP,
RTP and RTCP payload, or IP, UDP and RTCP.
However, if service information is received containing the 'b=TIAS' SDP parameter that corresponds to an SDP answer
payload, and if the P-CSCF supports this parameter, the P-CSCF may derive the bandwidth from this parameter rather
than from the 'b=AS' SDP parameter, as detailed in 3GPP TS 29.213 [9] subclause 6.2.
When available, the P-CSCF shall also indicate to PCRF, as a complement to the Service Information, the IMS
Communication Service Identifier within the AF-Application-Identifier AVP. The originating P-CSCF shall take the
IMS Communication Service Identifier value from the SIP response. The terminating P-CSCF shall take the IMS
Communication Service Identifier value from the SIP request. Otherwise, the P-CSCF may not be able to provide an
IMS Communication Service Identifier value to the PCRF. The format and specific headers where IMS communication
service identifiers are transported within SIP are defined in 3GPP TS 24.229 [17].
If the Service-URN AVP does not include an emergency service URN, i.e. a top-level service type of 'sos' as specified
in IETF RFC 5031 [21] and possibly additional sub-service information on the type of the emergency service and the
PCRF binds the IMS service session to an IP-CAN session established to an Emergency APN, the PCRF shall return an
AAA command with Experimental-Result-Code AVP set to the value
UNAUTHORIZED_NON_EMERGENCY_SESSION to the P-CSCF. Upon receiving an AAA with ExperimentalResult-Code AVP set to the value UNAUTHORIZED_NON_EMERGENCY_SESSION the P-CSCF shall apply the
procedures defined in 3GPP TS 24.229 [17].
NOTE:
The PCRF determines whether an IP-CAN session is established to an Emergency APN based on the
information received over Gx and operator configuration.
The PCRF may decide not to authorize requested service information. The PCRF will indicate it to the P-CSCF by
sending an AA-Answer with Experimental-Result-Code AVP set to the value
REQUESTED_SERVICE_NOT_AUTHORIZED. Upon receiving an AA-Answer with Experimental-Result-Code
AVP set to the value REQUESTED_SERVICE_NOT_AUTHORIZED the P-CSCF shall apply the procedures defined
in 3GPP TS 24.229 [17].
A.2
Enabling of IP Flows
Prior to the completion of the SIP session set-up, i.e. until the 200 OK (INVITE) or any other 2xx response is received,
the P-CSCF may enable or disable media IP flows depending on operator policy, thus allowing or forbidding early
media in forward and/or backward direction. Only to disable early media, the P-CSCF may modify the values of the
Flow-Status AVPs derived from SDP according to 3GPP TS 29.213 [9] clause 6.2. If the P-CSCF chooses to modify the
values, the P-CSCF shall store the last received SDP.
When a 2xx response is received, the P-CSCF shall enable all media IP flows according to the direction attribute within
the last received SDP, as specified in 3GPP TS 29.213 [9] clause 6.2. When a 2xx response is received and the P-CSCF
previously provided modified values of the Flow-Status AVPs in the session information, the P-CSCF shall provide
service information with values of the Flow-Status AVPs corresponding to the last received SDP.
NOTE:
In most cases a 2xx response is a 200 OK.
If the P-CSCF receives SDP answers after the completion of the SIP session set-up, i.e. after the 200 OK (INVITE) or
any other 2xx response is received, the P-CSCF shall provide the Flow-Status AVP, based on the last received SDP
answer. The Flow-Status AVP as derived from the SDP according to 3GPP TS 29.213 [9] clause 6.2.
ETSI
A.3
46
ETSI TS 129 214 V12.5.0 (2014-10)
Support for SIP forking
The P-CSCF shall be able to handle forking when PCC is applied. Forking can occur as specified in
3GPP TS 23.228 [16]. The related UE procedures are described in 3GPP TS 24.229 [17].
A.3.1
PCC rule provisioning for early media for forked responses
When a SIP session has been originated by a connected UE, the P-CSCF may receive multiple provisional responses
due to forking before the first final answer is received. Multiple early media session may be established during this
process.
The UE and the P-CSCF become aware of the forking only when a subsequent provisional response arrives for a new
early dialogue. After the first early media session is established, for each subsequent provisional response establishing
an additional early media session,, the P-CSCF shall use an AA request within the existing Diameter session containing
the SIP-Forking-Indication AVP with value SEVERAL_DIALOGUES and include the service information derived
from the latest provisional response.
The P-CSCF shall also provision the service information derived from any subsequent SDP offer-answer exchange
within an early dialogue (e.g. in PRACK and OK(PRACK), or UPDATE and OK(UPDATE) ) using an AA request
within the existing Diameter session containing the SIP-Forking-Indication AVP with value SEVERAL_DIALOGUES
and the derived service information.
When receiving an AA request containing the SIP-Forking-Indication AVP with value SEVERAL_DIALOGUES, the
PCRF shall identify the existing authorization information for that AF session. The PCRF shall send additional PCC
Rules or individual service data flow filters to already provide PCC rules as required by the Flow Description AVPs
within the session information to the PCEF. The PCRF shall authorize any additional media components and any
increased QoS requirements for the previously authorized media components, as requested within the service
information. The PCRF shall authorize the maximum bandwidth required by any of the dialogues, but not the sum of
the bandwidths required by all dialogues. Thus, the QoS authorized for a media component is equal to the highest QoS
requested for that media component by any of the forked responses. The PCRF shall open or close the gates for service
flows depending on the flow status that is being provisioned. However, if a flow ID has been enabled in uplink or
downlink direction or both way within previous service information, it shall remain enabled even if the PCRF receives
service information that disable this flow ID within an AA request containing the SIP-Forking-Indication AVP with
value SEVERAL_DIALOGUES.
A.3.2
Updating the provisioned PCC rules at the final answer
The P-CSCF shall store the SDP information for each early dialogue separately till the first final SIP answer is received.
Then the related early dialogue is progressed to an established dialogue to establish the final SIP session. All the other
early dialogues are terminated. The service information for the SIP session is updated to match the requirements of the
remaining early dialogue only.
When receiving the first final SIP response, the P-CSCF shall send an AA request without the SIP-Forking-Indication
AVP and include the service information derived from the SDP corresponding to the dialogue of the final response. The
P-CSCF shall provision the full service information including the applicable Flow-Description AVP(s) and Flow-Status
AVP(s).
When receiving an AA request with no SIP-Forking-Indication AVP or with a SIP-Forking-Indication AVP with value
SINGLE_DIALOGUE, the PCRF shall update installed PCC Rules information and Authorized-QoS information to
match only the requirements of the service information within this AA request. The PCRF should immediately remove
PCC Rule(s) or individual service data flow filters not matching IP flow(s) in the updated Service Information, to
reduce the risk for initial clipping of the media stream, and to minimize possible misuse of resources. The PCRF shall
also open or close the gates for service flows according to the flow status in the received service information.
ETSI
A.4
47
ETSI TS 129 214 V12.5.0 (2014-10)
Notification of AF Signalling Transmission Path

Status
When the P-CSCF receives an initial REGISTER SIP message from an attached UE, the P-CSCF may subscribe to
notifications of the status of the AF Signalling transmission path using the procedures specified in clause 4.4.5. Once
the P-CSCF has subscribed, the P-CSCF may receive notifications from the PCRF according to clause 4.4.6.3.
NOTE 1: When the Standardised QCI characteristics as defined in 3GPP TS 23.203 [2] are followed, the QCI for
IMS signalling will correspond to a non-GBR bearer. In this case, the P-CSCF will not receive
notifications related to the Specific-Action with value 'INDICATION_OF_LOSS_OF_BEARER'.
NOTE 2: This procedure is not applicable for IMS registrations for Emergency sessions.
The P-CSCF shall cancel the subscription to notification of the status of the AF Signalling transmission path when the
AF Signalling to that particular user is terminated (i.e. when the user is de-REGISTERED from the IM CN subsystem).
When the P-CSCF receives a notification of loss of signalling connectivity from the PCRF, the P-CSCF shall behave as
defined in 3GPP TS 24.229 [17].
A.5
Indication of Emergency Session
A SIP INVITE request can contain a service URN as defined in IETF RFC 5031 [21] within the request URI. If the
service within this URN is 'sos', possibly with additional sub-service information, the P-CSCF shall provision this
service and sub-service information within the Service-URN AVP towards the PCRF. The P-CSCF may also provision
possible information about other services received within the service URN.
A.6
Notification IP-CAN Type Change
When the P-CSCF receives an initial REGISTER SIP message from an attached UE, the P-CSCF mayrequest from the
PCRF the information about the type of IP-CAN the UE is attached to using the procedure specified in subclause 4.4.1.
NOTE: This procedure is not applicable for IMS registrations for Emergency sessions.
If the P-CSCF requests information about the type of IP-CAN,the P-CSCF shall also subscribe within the same AAR
command operation to notifications for changes of the IP-CAN type used by the UE. The P-CSCF shall include a
Specific-Action AVP in the AAR that is set to the value of IP-CAN_CHANGE.
When the P-CSCF receives the AA-Answer or RA-Request from the PCRF, the P-CSCF stores the IP-CAN type
information and the RAT type information (if also provided by the PCRF) and behaves as defined in 3GPP TS 24.229
[17].
The P-CSCF may receive notifications for changes of the IP-CAN type from the PCRF according to clause 4.4.6.4.
When the P-CSCF receives a notification of the change of the IP-CAN used by the UE, the P-CSCF stores the new IPCAN type information and behaves as defined in 3GPP TS 24.229 [17].
The P-CSCF shall cancel the subscription to notification for changes of the IP-CAN type used by the UE when the user
is de-REGISTERED from the IM CN subsystem.
ETSI
48
ETSI TS 129 214 V12.5.0 (2014-10)
A.7
Support for Early Session disposition SDP
A.7.1
General
As a network option, the P-CSCF may support the PCC procedures in the present Clause to handle 'early session'
disposition type SDP, as standardised in IETF RFC 3959 [27].
A.7.2
Service Information Provisioning for Early Media
The P-CSCF can receive 'early session' disposition SDP in addition to 'session' disposition SDP in SIP early dialogues.
The P-CSCF shall then provision service information derived both from the 'early session' disposition SDP and 'session'
disposition SDP applying the procedures in Clauses A.1, A.2, and A.3, and in the present Clause.
The P-CSCF shall apply the mapping rules in Annex B.1.2.2.2 to derive the flow identifiers from 'early session'
disposition SDP.
If a single media line with one media type (e.g. 'audio' or 'video') is contained in 'early session' disposition SDP and a
single media line with the same media type is contained in the 'session' disposition SDP of the same SIP dialogue, and
both media lines describe service flows of the same directionality (uplink, downlink, or bidirectional), the P-CSCF
should describe those SDP media lines in the same session information media component (with the same flow ID).
The 'early session' disposition SDP can also contain media lines of a type not included in the 'session' disposition SDP,
or several media lines of the same type. Such media components shall be described in own media components in the
service information.
If the P-CSCF desires to invoke special policies or separate event notifications for an 'early session' disposition media
line, it may choose to provision a separate session information media component even if a media line with the same
media type and directionality is contained in 'session' disposition SDP.
NOTE 1: A PCRF is then likely to supply separate PCC rules for early media and the corresponding final media.
This may lead to an over provisioning of resources during call establishment and a subsequent
reconfiguration of the radio bearer, or even to a call failure if the extra resources are not authorized or
available.
If the P-CSCF receives 'early session' disposition SDP before any 'session' disposition SDP and supplies service
information derived from the 'early session' disposition SDP at this point of time, it shall use dedicated media
components relating only to the 'early session' disposition SDP in the service information.
NOTE 2: The 'session' disposition SDP offer will frequently occur before the 'early session' disposition SDP offer,
but can also occur in parallel or in exceptional cases afterwards. The 'session' disposition SDP answer can
be contained in the same SIP message as the 'early session' disposition SDP offer, or can be sent in a 200
OK (INVITE), i.e. after the 'early session' disposition SDP answer.
If the P-CSCF includes any media component relating both to 'early session' disposition SDP and 'session' disposition
SDP in the service information, the P-CSCF shall:
-
provision the service information derived from 'early session' disposition SDP and the service information
derived from 'session' disposition SDP in separate Rx AA-Requests, and shall send a new Rx AA-Request only
after any previous Rx AA-Request has been acknowledged; and
provision the first service information (either derived from 'early session' disposition SDP or 'session' disposition
SDP) without the SIP-Forking-Indication AVP, or with the SIP-Forking-Indication AVP with value
SINGLE_DIALOGUE; and
provision all subsequent service information during ongoing call establishment with the SIP-Forking-Indication
AVP with value SEVERAL_DIALOGUES; and
if an SDP answer has been received and Codec-Data AVPs are provisioned within a Media-ComponentDescription AVP, provision a Codec-Data AVP derived from the corresponding offer together with a CodecData AVP derived from the SDP answer.
ETSI
49
ETSI TS 129 214 V12.5.0 (2014-10)
NOTE 3: The P-CSCF needs to provision the service information derived from 'early session' disposition SDP and
the service information derived from 'session' disposition SDP in separate Rx AA-Requests because the
encoding of the media-component does not allow for the simultaneous provisioning of two corresponding
filters.
NOTE 4: The PCRF will treat service information containing the SIP-Forking-Indication AVP as described in
Clause A.3.
A.7.3
Updating the Provisioned Service Information when

Dialogue is established
The P-CSCF shall store the SDP information for the 'session' disposition type until the first final SIP answer is received.
Then the early media described in the 'early session' disposition type SDP are terminated.
The P-CSCF shall then update the service information to match the requirements of the media described in the 'session'
disposition type SDP only:
-
If the P-CSCF included any media component relating both to 'early session' disposition SDP and 'session'
disposition SDP in the service information, the P-CSCF shall send an AA request without the SIP-ForkingIndication AVP or with a SIP-Forking-Indication AVP with value SINGLE_DIALOGUE and shall include the
service information derived from the 'session' disposition SDP. The P-CSCF shall provision the full service
information including the applicable Flow-Description AVP(s) and Flow-Status AVP(s).
The P-CSCF shall disable any media component(s) in the service information that relate to early media only by
setting their flow status to 'removed'.
A.8
Provision of Signalling Flow Information at P-CSCF
When the P-CSCF has successfully concluded the initial registration of an attached UE, i.e., when the P-CSCF has sent
to the UE a SIP 200 (OK) response to the SIP REGISTER request, the P-CSCF may provision information about the
SIP signalling flows between the UE and itself using the procedure specified in subclause 4.4.5a. If the P-CSCF already
has an open Rx Diameter session with the PCRF related to the signalling with the UE, e.g. one that has been opened
according to the procedure described in subclause A.6 and/or in subclause A.4, the P-CSCF shall reuse the already open
session to provision the SIP Signalling IP Flow information.
NOTE: This procedure is not applicable for IMS registrations for Emergency sessions.
If the P-CSCF provisions information about SIP signalling flows, the P-CSCF shall ensure that for each signalling IP
flow information it provides, the Flow-Description AVP shall accurately reflect the IP flow information as seen in the
IP header "on the wire". The P-CSCF shall set the value of the AF-Signalling-Protocol AVP to "SIP".
When the P-CSCF de-registers the UE and terminates SIP Signalling to the UE, the P-CSCF shall de-provision the SIP
Signalling IP flow information from the PCRF as described in subclause 4.4.5a.
A.9
Handling of MPS Session
When the P-CSCF receives an authorised Resource-Priority header field or a temporarily authorised Resource-Priority
header field containing an appropriate namespace and priority value in SIP signaling, and recognizes the need for
priority treatment as specified in 3GPP TS 24.229 [17], the P-CSCF shall include the MPS-Identifier AVP and
Reservation-Priority AVP in the AAR command towards the PCRF. The MPS-Identifier AVP shall contain the
national variant for MPS service name indicating an MPS session. The Reservation-Priority AVP shall include the
priority value of the related priority service. The Reservation-Priority AVP shall be populated with a default value if
the priority value is unknown.
NOTE 1: Various mechanisms can be applied to recognize the need for priority treatment in the P-CSCF (e.g.,
based on the dialled digits), according to national regulation and network configuration, as stated in 3GPP
TS 24.229 [17].
ETSI
50
ETSI TS 129 214 V12.5.0 (2014-10)
NOTE 2: Lowest user priority value shall be mapped in the corresponding lowest enumerated value of the
Reservation-Priority AVP.
Upon reception of a request that requires MPS treatment, the PCRF shall derive the PCC/QoS Rules corresponding to
the MPS session, as appropriate. The PCRF shall take specific actions on the corresponding IP-CAN to ensure that the
MPS session is prioritized, as described in 3GPP TS 29.212 [8], clause 4.5.19.1.3.
When the P-CSCF terminates the MPS session, the PCRF shall delete the PCC/QoS Rules corresponding to the MPS
session. The PCRF shall revoke the actions related to the prioritization of the MPS session in the corresponding IPCAN, as described in 3GPP TS 29.212 [8], clause 4.5.19.1.3.
A.10
Retrieval of network provided location information
A.10.1 General
According to Annex E.7 of 3GPP TS 23.228 [16], the P-CSCF can use PCC to retrieve network provided location
information. Information flows related to the distribution of network provided location information within the IMS are
provided in Annex R of 3GPP TS 23.228 [16].
This sublause provides optional PCC procedures to support the retrieval of network provided location information.
The originating P-CSCF can, depending on operator policy, retrieve the user location and/or UE Time Zone information
either before sending the INVITE towards the terminating side or upon reception of the SDP answer from the
terminating side.
A.10.2 Retrieval of network provided location information at

originating P-CSCF for inclusion in SIP Request
If the originating P-CSCF is required by operator policy to retrieve network provided location information before
forwarding a SIP INVITE request, upon reception of an INVITE/UPDATE request, the P-CSCF shall send an AARequest according to subclause 4.4.1 (SIP INVITE request) or 4.4.2 (SIP INVITE/UPDATE request) including:
-
the 'ACCESS_NETWORK_INFO_REPORT' value within the Specific-Action AVP; and
the required access network information within the Required-Access-Info AVP.
If the SIP INVITE request is an initial SIP INVITE request, the P-CSCF shall establish an Rx session for the new SIP
session with the AA-Request according to subclause 4.4.6.7 (if no session information is included) or 4.4.1 (if
preliminary session information is included).
The P-CSCF will receive the access network information from the PCRF in an RAR, and should include this access
network information in the SIP INVITE/UPDATE requests that it forwards. When the retrieved access network
information corresponds to the TWAN-Identifier AVP, the P-CSCF may also map the retrieved access network
information to a Geographical Identifier for routing, as specified in Annex E.8 of 3GPP TS 23.228 [16].

originating P-CSCF for inclusion in SIP response
confirmation
If an originating P-CSCF is required by operator policy to retrieve network provided location information before
forwarding an SDP answer, the P-CSCF shall apply the following procedures:
Upon reception of an SDP offer, the P-CSCF may send an AA-Request to the PCRF according to subclause A.1 and
may include in this AA-request:
-
ETSI
51
ETSI TS 129 214 V12.5.0 (2014-10)
Upon reception of an SDP answer, the P-CSCF will send an AA-Request to the PCRF according to subclause A.1. If the
P-CSCF has not requested access network information upon reception of the SDP offer, the P-CSCF shall include in
this AA-request:
-
network information in the SIP message with the response confirmation before forwarding it. When the retrieved access
network information corresponds to the TWAN-Identifier AVP, the P-CSCF may also map the retrieved access network
information to a Geographical Identifier for routing, as specified in Annex E.8 of 3GPP TS 23.228 [16].

terminating P-CSCF
If a terminating P-CSCF is required by operator policy to retrieve network provided location information at session
establishment and/or modification, when receiving a SIP response, the P-CSCF shall apply the following procedures:
Upon reception of a SIP response that requires the inclusion of access network information and includes an SDP
answer, the P-CSCF will send an AA-Request to the PCRF according to subclause A.1 and shall include in this AArequest:
-
Upon reception of a SIP response that requires the inclusion of access network information and includes no SDP
answer, the P-CSCF shall send an AA-Request including:
-
The P-CSCF may also include in the AA-Request

-
service information derived from an SDP offer within the SIP response; and
the Service-Info-Status AVP with the value set to PRELIMINARY SERVICE INFORMATION.
If the SIP INVITE request is an initial SIP INVITE request, the P-CSCF shall establish an Rx session for the new SIP
session with the AA-Request according to subclause 4.4.6.7 (if no session information is included) or 4.4.1 (if
If an Rx session related to service data has not yet been established, the P-CSCF shall establish an Rx session for the
new SIP session with the AA-Request according to subclause 4.4.6.7 (if no session information is included) or 4.4.1 (if
network information in the SIP response before forwarding it. When the retrieved access network information
corresponds to the TWAN-Identifier AVP, the P-CSCF may also map the retrieved access network information to a
Geographical Identifier for routing, as specified in Annex E.8 of 3GPP TS 23.228 [16].
A.10.5 Provisioning of network provided location information at SIP

session release
If a P-CSCF is required by operator policy to include network provided location information in SIP session release
signalling, the P-CSCF shall apply the following procedures:
ETSI
52
ETSI TS 129 214 V12.5.0 (2014-10)
Upon reception of a SIP session release request that requires the inclusion of network provided location information, the
P-CSCF will send an ST-Request and shall include in this request the required access network information within the
Required-Access-Info AVP.
The P-CSCF will receive the access network information from the PCRF in the corresponding ST-Answer, and should
include this access network information either in the SIP session termination request (at the originating side) or a reply
to the SIP session termination request (at the terminating side). When the retrieved access network information
corresponds to the TWAN-Identifier AVP, the P-CSCF may also map the retrieved access network information to a
Geographical Identifier for routing, as specified in Annex E.8 of 3GPP TS 23.228 [16].
ETSI
53
ETSI TS 129 214 V12.5.0 (2014-10)
Annex B (normative):
Flow identifiers: Format definition and examples
B.1
Format of a flow identifier
B.1.1
General
A flow identifier is expressed as a 2-tuple as follows:

<The ordinal number of the position of the media component description in the SDI , The ordinal number of the
IP flow(s) within the media component description assigned in the order of increasing downlink port numbers as
detailed below >
where both are numbered starting from 1. The encoding of the flow identifier is as indicated in 3GPP TS 24.008 [12].
If UE and AF share an algorithm for a given application, which guarantees that UE and AF assign the same ordinal
number to each media component, the ordinal numbers of the IP Flows within a media component shall be assigned
according to the following rules:
-
All IP flow(s) or bidirectional combinations of two IP flow(s) within the media component, for which a
downlink destination port number is available, shall be assigned ordinal numbers in the order of downlink
destination port numbers.
All IP flows, where no downlink destination port number is available, shall be assigned the next higher ordinal
numbers in the order of uplink destination port numbers.
The ordinal number of a media component shall not be changed when the session description information is modified.
If no SDI with fixed and unique positions for media components is exchanged between UE and AF, the UE and AF may
assign the ordinal numbers of the media components in another application-dependent algorithm which guarantees that
UE and AF assign the same ordinal number to each media component.
If UE and AF do not share an algorithm for a given application, which guarantees that UE and AF assign the same
ordinal number to each media component, the ordinal number of the media component shall be set to zero and the
ordinal number of the IP flows shall be assigned according to the following rules:
1. If ordinal numbers for several IP flows are assigned at the same time, all uplink IP flows shall be assigned lower
ordinal number than all downlink IP flows.
2. If ordinal numbers for several IP flows are assigned at the same time, all uplink and all downlink IP flows shall
separately be assigned ordinal numbers according to increasing internet protocol number assigned by IANA (e.g.
6 for TCP and 17 for UDP)
3. If ordinal numbers for several IP flows are assigned at the same time, for each internet protocol with a port
concept, all uplink and all downlink IP flows of this internet protocol shall separately be assigned ordinal
numbers according to increasing port numbers.
4. If IP flows are removed from an existing session, the previously assigned binding info shall remain unmodified
for the remaining IP flows.
5. If IP flows are added to an existing session, the previously assigned binding info shall remain unmodified and
the new IP flows shall be assigned ordinal numbers following the rules 1. To 3., starting with the first previously
unused ordinal number. The numbers freed in step 4. Shall not be reused.
If the IP flows correspond to AF signalling (e.g. SIP signalling IP Flows), and no IP flow information is provided both
the ordinal number of the media component and the IP flows shall be set to zero. In the case when the IP flow
information of the AF signalling is provided, the ordinal number of the media component will be set to zero, and the
ordinal number(s) of the IP flows shall follow the rules set above for the case when the UE and AF do not share an
algorithm for a given application.
ETSI
B.1.2
54
ETSI TS 129 214 V12.5.0 (2014-10)
Derivation of Flow Identifiers from SDP
B.1.2.1 Standard Procedure

The procedure in Table B.1.2.1.1 shall be applied for SDP of 'session' disposition type within SIP and for all SDP
outside SIP.
Table B.1.2.1.1: Standard Procedure to derive Flow Identifiers from SDP
The ordinal number of the position of the media
component
The ordinal number of the position of the 'm=' line in
the SDP
The ordinal number of the IP flow(s) within the media

component description
The ordinal number of the IP flow(s) within the 'm=' line assigned
in the order of increasing downlink destination port numbers, if
downlink destination port numbers are available. For uplink or
inactive unicast media IP flows, a downlink destination port
number is nevertheless available, if SDP offer-answer according
to RFC 3264 is used.
The ordinal number of the IP flow(s) within the 'm=' line assigned
in the order of increasing uplink destination port numbers, if no
downlink destination port numbers are available.
B.1.2.2 SDP with 'early session' disposition type

The procedure in Table B.1.2.2.1 shall be applied for SDP of 'early session' disposition type within SIP. The 'early
session' disposition type is specified within IETF RFC 3959 [27].
Table B.1.2.2.1: Procedure to derive Flow Identifiers from 'early session' disposition SDP
The ordinal number of the position of the media
component
If a single media component with one media type

(e.g. 'audio' or 'video') is contained in 'early session'
disposition SDP and a single media component
with the same media type is contained in the
'session' disposition SDP of the same SIP dialogue,
and if both SDP media components are described in
a single Rx service information media component,
that Rx service information media component shall
obtain the media component number derived from
'session' disposition SDP following the rules in
table B.1.2.1.1.
Otherwise each media component shall obtain the
ordinal number of the position of the 'm=' line in
the 'early session' disposition SDP plus 1000 as
media component ordinal number.
B.2
The ordinal number of the IP flow(s) within the media

component description
As in table B.1.2.1.1.
Example 1
An UE, as the offerer, sends a SDP session description, as shown in table B.2.1, to an application server (only relevant
SDP parameters are shown):
Table B.2.1: The values of the SDP parameters sent by the UE in example 1.
V=0
o=ecsreid 3262464865 3262464868 IN IP6 2001:0646:00F1:0045:02D0:59FF:FE14:F33A
s=MM01
i=One unidirectional audio media and one unidirectional video media and one bidirectional application
ETSI
55
ETSI TS 129 214 V12.5.0 (2014-10)
media
t=3262377600 3262809600
m=video 50230 RTP/AVP 31
c=IN IP6 2001:0646:00F1:0045:02D0:59FF:FE14:F33A
a=recvonly
m=audio 50330 RTP/AVP 0
c=IN IP6 2001:0646:00F1:0045:02D0:59FF:FE14:F33A
a=sendonly
m=application 50430 udp wb
c=IN IP6 2001:0646:00F1:0045:02D0:59FF:FE14:F33A
a=sendrecv
and receives the SDP parameters, as shown in table B.2.2, from the application server:
Table B.2.2: The values of the SDP parameters sent by the application server in example 1.
V=0
s=MM01
i=One unidirectional audio media and one unidirectional video media and one bidirectional application
media
t=3262377600 3262809600
c=IN IP6 2001:0646:000A:03A7:02D0:59FF:FE40:2014
a=sendonly
m=audio 49170 RTP/AVP 0
c=IN IP6 2001:0646:000A:03A7:02D0:59FF:FE40:2014
a=recvonly
m=application 32416 udp wb
c=IN IP6 2001:0646:000A:03A7:0250:DAFF:FE0E:C6F2
a=sendrecv
From this offeranswer exchange of SDP parameters the UE and the PCRF each creates a list of flow identifiers
comprising the IP flows as shown in table B.2.3:
Table B.2.3: Flow identifiers in example 1.
Order of
"m="-line
1
1
1
2
2
2
3
3
B.3
Type of IP flows
RTP (Video) DL
RTCP DL
RTCP UL
RTP (Audio) UL
RTCP DL
RTCP UL
UDP (application) DL
UDP (application) UL
Destination IP address / Port number of the IP flows
Flow identifier
2001:0646:00F1:0045:02D0:59FF:FE14:F33A / 50230
2001:0646:00F1:0045:02D0:59FF:FE14:F33A / 50231
2001:0646:000A:03A7:02D0:59FF:FE40:2014 / 51373
2001:0646:000A:03A7:02D0:59FF:FE40:2014 / 49170
2001:0646:00F1:0045:02D0:59FF:FE14:F33A / 50331
2001:0646:000A:03A7:02D0:59FF:FE40:2014 / 49171
2001:0646:00F1:0045:02D0:59FF:FE14:F33A / 50430
2001:0646:000A:037:0250:DAFF:FE0E:C6F2 / 32416
<1,1>
<1,2>
<1,2>
<2,1>
<2,2>
<2,2>
<3,1>
<3,1>
Example 2
In the general case, multiple ports may be specified with a 'number of ports' qualifier as follows, RFC 2327 [17]:
m=<media> <port>/<number of ports> <transport> <fmt list>
ETSI
56
ETSI TS 129 214 V12.5.0 (2014-10)
v=0
s=MM02
i=One unidirectional audio media consisting of two media IP flows described by one media
component
t=3262377600 3262809600
m=audio 50330/2 RTP/AVP 0
c=IN IP6 2001:0646:00F1:0045:02D0:59FF:FE14:F33A
a=recvonly
Table B.3.2: The values of the SDP parameters sent by the application server in example 2.
v=0
s=MM02
i=One unidirectional audio media consisting of two media IP flows described by one media
component
t=3262377600 3262809600
m=audio 49170/2 RTP/AVP 0
c=IN IP6 2001:0646:000A:03A7:02D0:59FF:FE40:2014
a=sendonly
Order of
"m="-line
1
1
1
1
1
1
B.4
Type of IP flows
RTP (audio) DL
RTCP DL
RTCP UL
RTP (audio) DL
RTCP DL
RTCP UL
Flow identifier
2001:0646:00F1:0045:02D0:59FF:FE14:F33A / 50330
2001:0646:00F1:0045:02D0:59FF:FE14:F33A / 50331
2001:0646:000A:03A7:02D0:59FF:FE40:2014 / 49171
2001:0646:00F1:0045:02D0:59FF:FE14:F33A / 50332
2001:0646:00F1:0045:02D0:59FF:FE14:F33A / 50333
2001:0646:000A:03A7:02D0:59FF:FE40:2014 / 49173
<1,1>
<1,2>
<1,2>
<1,3>
<1,4>
<1,4>
Example 3 without media components.
The UE and AF do not exchange SDP for an application and do not share an algorithm, which guarantees that UE and
AF assign the same ordinal number to each media component.
At the AF session initiation, the UE and AF agree to set up the following IP flows:
-
Uplink UDP flow with destination port 100.
Downlink UDP flow with destination port 100.
Downlink TCP flow with destination port 100.
Uplink TCP flow with destination port 100.
ETSI
57
ETSI TS 129 214 V12.5.0 (2014-10)
The following binding info is assigned to these IP flows.

-
Uplink UDP flow with destination port 100:
(0, 2)
Downlink UDP flow with destination port 100:
(0, 5)
Downlink TCP flow with destination port 100:
(0, 4)
Uplink TCP flow with destination port 100:
(0, 1)
(0, 3)
At a later stage in the session, the TCP IP flows are removed and the following IP flows are added:
-
Downlink UDP flow with destination port 50.
The following binding info is assigned to the IP flows existing at this stage:
-
(0, 2)
(0, 5)
(0, 3)
(0, 6)
(0, 7)
B.5
Example 4
In this example, the SDP 'a=rtcp' attribute defined in IETF RFC 3605 is used.
V=0
s=MM01
i=One unidirectional video media
t=3262377600 3262809600
c=IN IP6 2001:0646:00F1:0045:02D0:59FF:FE14:F33A
a=recvonly
a=rtcp: 49320
Table C.5.2: The values of the SDP parameters sent by the application server in example 1.
V=0
s=MM01
i=One unidirectional video media
t=3262377600 3262809600
c=IN IP6 2001:0646:000A:03A7:02D0:59FF:FE40:2014
a=sendonly
ETSI
58
ETSI TS 129 214 V12.5.0 (2014-10)
a=rtcp:53020
Order of
"m="-line
1
1
1
Type of IP flows
RTP (Video) DL
RTCP DL
RTCP UL
Flow identifier
2001:0646:00F1:0045:02D0:59FF:FE14:F33A / 50230
2001:0646:00F1:0045:02D0:59FF:FE14:F33A / 49320
2001:0646:000A:03A7:02D0:59FF:FE40:2014 / 53020
<1,2>
<1,1>
<1,1>
ETSI
59
Annex C (informative):
Void
ETSI
ETSI TS 129 214 V12.5.0 (2014-10)
60
ETSI TS 129 214 V12.5.0 (2014-10)
Annex D (informative):
Change history
Date
TSG #
TSG Doc.
CR
11/11/2005
17/02/2006
13/09/2006
15/09/2006
11/11/2006
01/12/2006
10/01/2007
TSG#33
TSG#33
CP-060637
15/02/2007
28/02/2007
09/03/2007
TSG#35
TSG#35
CP-070099
03-2007
06-2007
06-2007
06-2007
06-2007
06-2007
06-2007
06-2007
06-2007
06-2007
09-2007
09-2007
09-2007
09-2007
09-2007
09-2007
09-2007
12-2007
TSG#36
TSG#36
TSG#36
TSG#36
TSG#36
TSG#36
TSG#36
TSG#36
TSG#36
TSG#37
TSG#37
TSG#37
TSG#37
TSG#37
TSG#37
TSG#37
TSG#38
CP-070423
CP-070423
CP-070423
CP-070423
CP-070423
CP-070494
CP-070423
CP-070423
CP-070423
CP-070558
CP-070558
CP-070559
CP-070558
CP-070558
CP-070558
CP-070558
CP-070728
001
002
003
005
007
008
013
017
020
022
023
025
026
028
030
033
032
12-2007
12-2007
12-2007
12-2007
03-2008
03-2008
05-2008
05-2008
05-2008
05-2008
05-2008
05-2008
05-2008
09-2008
12-2008
12-2008
12-2008
12-2008
TSG#38
TSG#38
TSG#38
TSG#38
TSG#39
TSG#39
TSG#40
TSG#40
TSG#40
TSG#40
TSG#40
TSG#40
TSG#40
TSG#41
TSG#42
TSG#42
TSG#42
TSG#42
CP-070728
CP-070728
CP-070728
CP-070728
CP-080040
CP-080046
CP-080298
CP-080296
CP-080292
CP-080299
CP-080292
CP-080299
CP-080299
CP-080487
CP-080751
CP-080768
CP-080760
CP-080751
037
038
039
041
042
044
048
049
051
052
054
055
057
068
072
076
081
085
R Subject/Comment
ev
Includes the following TDOCs agreed at CT3#38:
C3-050693, C3-050837, C3-050838, C3-050844, C3-050845
C3-060101, C3-060102, C3-060125, C3-060112, C3-060133,
C3-060114, C3-060136, C3-060116
C3-060446, C3-060447, C3-060556, C3-060538, C3-060451,
C3-C3-060453, C3-060540, C3-060496, C3-060544
Implementation of C3-060539 missing in former version and
correction of an editorial error in C3-060496 implementation.
C3-060605, C3-060639, , C3-060643, C3-060655, C3-060780,
C3-060783, C3-060784, C3-060826, C3-060827, C3-060852,
C3-060853
Editorial update by MCC for presentation to TSG CT for information
The misimplemented style of editor"s notes in clause 4.3.2 was
corrected to normal by MCC.
C3-070063, C3-070086, C3-070118, C3-070139, C3-070151, C3070189, C3-070217, C3-070218, C3-070221, C3-070236, C3070254
Editorial update by MCC for presentation to TSG CT for approval
References to annex B in chapter 5 were replaced by 'annex tbd'
by Ragnar Huslende (CT3 Chairman), as agreed by CT#35
MCC update to version 7.0.0 after approval at TSG CT#35
2 PCRF assure emergency bearer for emergency service
7 Signalling Path Status detected
AF-Application Identifier at AF session level
2 Alignment of PCRF Acknowledgment to AF
2 Addition of Flow identifier annex
3 Routeing of Diameter commands Rx
1 Various Minor Corrections
2 Handling of disabled flows for forking
Diameter application ID
1 The input for PCC decisions
1 Session Binding Error
2 Service Information accepted by PCRF
TS Clean-Up
1 Origin-State-Id AVP missing in AA commands
2 Clarification of PCRF Procedures
1 Correction of implementation error of CR0013
5 Providing User"s IP-CAN Type and subscription for IP-CAN Type
change notification to AF
1 Provisioning of Service Information at P-CSCF
3 Clarification on IMS Communication Service Identifier over Rx
Removal of Emergency Services
1 Adding Destination-Host to AAR
1 Adding missing AVPs to Rx commands ABNF
1 Clarification on Notification in Rx Interface
3 AVP and Command Code updates for Common IMS
1 Supporting third party application server for AF
1 Support of TCP-based media in PCC
3 IP-CAN Type verification
1 Notification of Relase of Signalling Bearer
2 IP CAN session definition update
2 RAT type AVP
3 PDN information in Rx interface
Update of IETF references
1 Out of credit indication, OFF only
1 Update Reference Model
Network-only bearer control mode
ETSI
Old
New
0.0.0
0.1.0
0.1.0
0.2.0
0.2.0
0.3.0
0.3.0
0.4.0
0.4.0
0.5.0
0.5.0
1.0.0
1.0.0
1.0.1
1.0.1
1.1.0
1.1.0
2.0.0
2.0.0
2.1.0
2.1.0
7.0.0
7.0.0
7.0.0
7.0.0
7.0.0
7.0.0
7.0.0
7.0.0
7.0.0
7.1.0
7.1.0
7.1.0
7.1.0
7.1.0
7.1.0
7.1.0
7.2.0
7.0.0
7.1.0
7.1.0
7.1.0
7.1.0
7.1.0
7.1.0
7.1.0
7.1.0
7.1.0
7.2.0
7.2.0
7.2.0
7.2.0
7.2.0
7.2.0
7.2.0
7.3.0
7.2.0
7.2.0
7.2.0
7.2.0
7.3.0
7.4.0
8.0.0
8.0.0
8.0.0
8.0.0
8.0.0
8.0.0
8.0.0
8.1.0
8.2.0
8.2.0
8.2.0
8.2.0
7.3.0
7.3.0
7.3.0
7.3.0
7.4.0
8.0.0
8.1.0
8.1.0
8.1.0
8.1.0
8.1.0
8.1.0
8.1.0
8.2.0
8.3.0
8.3.0
8.3.0
8.3.0

12-2008
12-2008
03-2009
03-2009
03-2009
03-2009
05-2009
05-2009
05-2009
05-2009
05-2009
05-2009
09-2009
12-2009
12-2009
12-2009
12-2009
12-2009
12-2009
03-2010
03-2010
03-2010
03-2010
03-2010
09-2010
09-2010
09-2010
12-2010
12-2010
12-2010
03-2011
03-2011
03-2011
03-2011
03-2011
03-2011
03-2011
03-2011
03-2011
03-2011
06-2011
06-2011
TSG#42
TSG#42
TSG#43
TSG#43
TSG#43
TSG#43
TSG#44
TSG#44
TSG#44
TSG#44
TSG#44
TSG#44
TSG#45
TSG#46
TSG#46
TSG#46
TSG#46
TSG#46
TSG#46
TSG#47
TSG#47
TSG#47
TSG#47
TSG#47
TSG#49
TSG#49
TSG#49
TSG#50
TSG#50
TSG#50
TSG#51
TSG#51
TSG#51
TSG#51
TSG#51
TSG#51
TSG#51
TSG#51
TSG#51
TSG#51
TSG#52
TSG#52
CP-080751
CP-080923
CP-090074
CP-090082
CP-090096
CP-090096
CP-090339
CP-090346
CP-090339
CP-090334
CP-090339
CP-090353
CP-090573
CP-090842
CP-090857
CP-090838
CP-090842
CP-090857
CP-090838
CP-100070
CP-100076
CP-100086
CP-100070
CP-100076
CP-100626
CP-100561
087
088
091
093
095
096
098
100
101
103
104
099
112
116
117
120
122
127
130
137
139
140
143
145
147
148
CP-100791
CP-100771
CP-100791
CP-110125
CP-110125
CP-110125
CP-110114
CP-110125
CP-110125
CP-110121
CP-110125
CP-110125
CP-110133
CP-110405
CP-110413
150
153
154
159
161
162
165
167
168
171
172
173
170
180
182
3
1
2
3
4
2
1
1
5
1
2
06-2011
06-2011
06-2011
06-2011
TSG#52
TSG#52
TSG#52
TSG#52
CP-110409
CP-110411
CP-110413
CP-110425
185
187
189
190
06-2011
09-2011
09-2011
12-2011
12-2011
12-2011
03-2012
03-2012
03-2012
06-2012
TSG#52
TSG#53
TSG#53
TSG#54
TSG#54
TSG#54
TSG#55
TSG#55
TSG#55
TSG#56
CP-110424
CP-110608
CP-110608
CP-110935
CP-110827
CP-110835
CP-120077
CP-120066
CP-120077
CP-120354
191
195
199
204
208
210
212
214
215
223
2
2
06-2012
06-2012
09-2012
09-2012
09-2012
09-2012
09-2012
12-2012
12-2012
12-2012
12-2012
TSG#56
TSG#56
TSG#57
TSG#57
TSG#57
TSG#57
TSG#57
TSG#58
TSG#58
TSG#58
TSG#58
CP-120345
CP-120358
CP-120511
CP-120646
CP-120514
CP-120536
CP-120655
CP-120843
CP-120824
CP-120843
CP-120916
224
228
233
238
242
245
246
247
251
253
255
2
1
1
1
2
2
1
2
1
1
4
1
1
1
2
2
3
1
1
2
3
1
2
3
2
1
3
4
1
1
2
3
1
2
1
2
1
1
1
1
1
1
1
2
61
ETSI TS 129 214 V12.5.0 (2014-10)
Service information request

Support of TIAS parameter
Experimental-Result AVP usage on Rx
Adding Supported-Features AVP to Rx commands
Rx Diameter Sessions
IMS session setup with UE initiated resource reservation
Resource allocation subscription in Rx
ICS impact on PCC
Correction to feature bit definition
Deleting INDICATION_OF_LOSS_OF_BEARER Event
Limited PCC Deployment
Preventing the use of an Emergency APN for Non-emergency calls
Limited PCC deployment
Access Network Charging Identifier handling in Rx
PCC handling of SDP of early session disposition type
Use of Ipv6 Prefix
Corrections for PCC/QoS rule modification failure
Supported Features for Rel-9 Rx
Rx request handling
Correcting the reference of Annex 5
Correction of Flow-Description AVP description
IMS Restoration procedure over Rx
Notification about RAT-type change
Supported-Feature feature bit definitions
3GPP References to TISPAN specifications
Impacts of IFOM on Rx interface
Editorial correction by MCC
Additions to support sponsored connectivity
Specific-Action AVP to report specific actions
UDR and Ud in PCC Architecture
Authorization of the sponsored data connectivity
ASP operators information for sponsored data connectivity
Usage for sponsored connectivity
Fixing Supported-Feature feature bit definitions
Correction to feature bit for sponsored data connectivity
Correction to the Reporting Usage for Sponsored Data Connectivity
Support of MPS over Rx
Some editorial corrections for sponsored data connectivity
Requesting Usage Monitoring Control for sponsored connectivity
Sd reference point in PCC Architecture
PS-to-CS HO indicator in Rx
Sponsor-Identity AVP & Application-Service-Provider-Identity AVP
format.
Some corrections for IFOM
Supported-Features bit for eMPS
Limit the sponsored data connectivity in the roaming case
Subscriber Spending Limits based on Sy reference point (R11
29.214)
Request Type in Rx AAR
UE Ipv6 prefix allocation clean-up
Correction to the architecture figure(Rel-11)
Alignment of PCC reference architecture with Stage 2 specification
Correction in AVP names
Flows AVP in AAA command
Multiple instances of the Subscription Id (R11 29.214)
QoS support for 3GP-DASH Services
Asserted ICSI over Rx
Support network location reporting for IMS functionality over Rx
interface (R11 29214)
Support for local address in TFT filters AVP (TS 29.214)
Correction to the reference of TS 29.214 (R11)
Correction of assigned internet protocol number
Addition of PLMN ID for NETLOC in TS 29.214
Applicable IP-CAN Type
Reporting multiple events to AF
Reference list correction to align with the corrected TS 29.212 title
Clarification of Supported-Features AVP
PCC procedures for Rx sessions with no service information
Clean up of Editor"s Notes
Correction of Rx reference point for PCRF addressing
ETSI
8.2.0
8.2.0
8.3.0
8.3.0
8.3.0
8.3.0
8.4.0
8.4.0
8.4.0
8.4.0
8.4.0
8.5.0
9.0.0
9.1.0
9.1.0
9.1.0
9.1.0
9.1.0
9.1.0
9.2.0
9.2.0
9.2.0
9.2.0
9.2.0
9.3.0
9.4.0
10.0.0
10.0.1
10.0.1
10.0.1
10.1.0
10.1.0
10.1.0
10.1.0
10.1.0
10.1.0
10.1.0
10.1.0
10.1.0
10.2.0
11.0.0
11.0.0
8.3.0
8.3.0
8.4.0
8.4.0
8.4.0
8.4.0
8.5.0
8.5.0
8.5.0
8.5.0
8.5.0
9.0.0
9.1.0
9.2.0
9.2.0
9.2.0
9.2.0
9.2.0
9.2.0
9.3.0
9.3.0
9.3.0
9.3.0
9.3.0
9.4.0
10.0.0
10.0.1
10.1.0
10.1.0
10.1.0
10.2.0
10.2.0
10.2.0
10.2.0
10.2.0
10.2.0
10.2.0
10.2.0
10.2.0
11.0.0
11.1.0
11.1.0
11.0.0
11.0.0
11.0.0
11.0.0
11.1.0
11.1.0
11.1.0
11.1.0
11.0.0
11.1.0
11.1.0
11.2.0
11.2.0
11.2.0
11.3.0
11.3.0
11.3.0
11.4.0
11.1.0
11.2.0
11.2.0
11.3.0
11.3.0
11.3.0
11.4.0
11.4.0
11.4.0
11.5.0
11.4.0
11.4.0
11.5.0
11.5.0
11.5.0
11.5.0
11.5.0
11.6.0
11.6.0
11.6.0
11.6.0
11.5.0
11.5.0
11.6.0
11.6.0
11.6.0
11.6.0
11.6.0
11.7.0
11.7.0
11.7.0
11.7.0

03-2013
06-2013
06-2013
06-2013
06-2013
06-2013
09-2013
09-2013
TSG#59
TSG#60
TSG#60
TSG#60
TSG#60
TSG#60
TSG#61
TSG#61
CP-130059
CP-130331
CP-130316
CP-130331
CP-130341
CP-130348
CP-130543
CP-130553
267
272
278
281
270
280
291
293
1
2
3
3
1
09-2013
12-2013
TSG#61
TSG#62
CP-130549 295
CP-130680 298
2
1
12-2013
12-2013
12-2013
12-2013
03-2014
03-2014
06-2014
06-2014
06-2014
06-2014
06-2014
06-2014
06-2014
06-2014
06-2014
TSG#62
TSG#62
TSG#62
TSG#62
TSG#63
TSG"#63
TSG#64
TSG#64
TSG#64
TSG#64
TSG#64
TSG#64
TSG#64
TSG#64
TSG#64
CP-130663
CP-130685
CP-130669
CP-130678
CP-140066
CP-140087
CP-140377
CP-140390
CP-140400
CP-140401
CP-140402
CP-140402
CP-140409
CP-140409
CP-140409
2
2
1
07-2014
09-2014
09-2014
CT-65
CT-65
CP-140530 0344
CP-140530 0352
09-2014
CT-65
CP-140533 0345
09-2014
09-2014
CT-65
CT-65
CP-140545 0350
CP-140551 0349
1
3
303
308
313
315
322
318
328
329
333
341
332
327
337
339
335
1
1
1
4
2
1
1
1
1
2
3
1
5
62
ETSI TS 129 214 V12.5.0 (2014-10)
Cancelling subscription to notification of ignalling path status

User Location Information Age
Correction to the limited PCC deployment report
Network provided location information related corrections
Reference model update to include Gyn and Gzn
Time-based usage monitoring control
Correction to resource allocation handling
One-time specific action for retrieval of network provided location
info.
SGW Restoration impacts in Rx reference point
Correction to the applicability of Specific-Action AVP value in
temporary network failure handling
IP-CAN type notification correction
Handling of Loss of Bearer Specific Action
Correction on Sponsored-Data-Connectivity AVP
Correction on user location information time description
Correction of IMS emergency procedures for SIP Registration
Access network information reporting in case of a TWAN access
Enhancement in IMS Restoration procedure
Geographical Identifier for TWAN access
Reporting the RAN/NAS release cause on Rx interface
Diameter Overload Control for Rx
Correct the description of Sponsored-Connectivity-Data AVP
Provisioning of AF Signalling Flow Information
Access Network Information Reporting Capability
Correction to the subscription of specific actions in AA-Request
Corrections to access network information reporting during IP-CAN
session termination
One cross-reference updated in clause 4.1
Correction to access network information reporting in IMS
Access Network Information Reporting during the bearer
deactivation
Adding the missing case of bearer termination to the SpecificAction AVP
Group Communication Service support for Unicast bearers
Enhancement for P-CSCF Restoration
ETSI
11.7.0
11.8.0
11.8.0
11.8.0
11.9.0
11.9.0
12.0.0
12.0.0
11.8.0
11.9.0
11.9.0
11.9.0
12.0.0
12.0.0
12.1.0
12.1.0
12.0.0 12.1.0
12.1.0 12.2.0
12.1.0
12.1.0
12.1.0
12.1.0
12.2.0
12.2.0
12.3.0
12.3.0
12.3.0
12.3.0
12.3.0
12.3.0
12.3.0
12.3.0
12.3.0
12.2.0
12.2.0
12.2.0
12.2.0
12.3.0
12.3.0
12.4.0
12.4.0
12.4.0
12.4.0
12.4.0
12.4.0
12.4.0
12.4.0
12.4.0
12.4.0 12.4.1
12.4.0 12.5.0
12.4.0 12.5.0
12.4.0 12.5.0
12.4.0 12.5.0
12.4.0 12.5.0
63
History
Document history
V12.5.0
October 2014
Publication
ETSI
ETSI TS 129 214 V12.5.0 (2014-10)

Etsi TS 129 214

Uploaded by

Copyright:

Available Formats

Etsi TS 129 214

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Etsi TS 129 214

Uploaded by

Copyright:

Available Formats

ETSI TS 129 214 V12.5.

Universal Mobile Telecommunications System (UMTS);

3GPP TS 29.214 version 12.5.0 Release 12

ETSI TS 129 214 V12.5.0 (2014-10)

Siret N 348 623 562 00017 - NAF 742 C

3GPP TS 29.214 version 12.5.0 Release 12

ETSI TS 129 214 V12.5.0 (2014-10)

Intellectual Property Rights

Modal verbs terminology

3GPP TS 29.214 version 12.5.0 Release 12

ETSI TS 129 214 V12.5.0 (2014-10)

Definitions and abbreviations ...................................................................................................................8

Rx reference point ..................................................................................................................................10

3GPP TS 29.214 version 12.5.0 Release 12

ETSI TS 129 214 V12.5.0 (2014-10)

Media-Component-Number AVP ............................................................................................................... 31

IMS Related P-CSCF Procedures over Rx ..................................................44

Provision of Service Information at P-CSCF .........................................................................................44

Enabling of IP Flows ..............................................................................................................................45

Support for SIP forking ..........................................................................................................................46

Notification of AF Signalling Transmission Path Status .......................................................................47

Indication of Emergency Session ...........................................................................................................47

Notification IP-CAN Type Change ........................................................................................................47

Support for Early Session disposition SDP ............................................................................................48

Handling of MPS Session.......................................................................................................................49

A.10 Retrieval of network provided location information ..............................................................................50

3GPP TS 29.214 version 12.5.0 Release 12

ETSI TS 129 214 V12.5.0 (2014-10)

Flow identifiers: Format definition and examples ......................................53

Format of a flow identifier .....................................................................................................................53

Example 3 without media components...................................................................................................56

Change history ...............................................................................................60

3GPP TS 29.214 version 12.5.0 Release 12

ETSI TS 129 214 V12.5.0 (2014-10)

3GPP TS 29.214 version 12.5.0 Release 12

ETSI TS 129 214 V12.5.0 (2014-10)

3GPP TR 21.905: 'Vocabulary for 3GPP Specifications'.

3GPP TS 23.203: 'Policy and Charging Control architecture'.

3GPP TS 29.209: 'Policy control over Gq interface', latest Rel-6 version.

3GPP TS 29.212: 'Policy and Charging Control (PCC); Reference points'.

IETF RFC 3588: 'Diameter Base Protocol'.

IETF RFC 4005: 'Diameter Network Access Server Application'.

IETF RFC 4566 : 'SDP : Session Description Protocol''.

IETF RFC 4006: 'Diameter Credit Control Application'.

3GPP TS 23.228: 'IP Multimedia Subsystem (IMS); Stage 2'.

3GPP TS 29.214 version 12.5.0 Release 12

ETSI TS 129 214 V12.5.0 (2014-10)

IETF RFC 3162: 'Radius and Ipv6'.

3GPP TS 32.240: 'Telecommunication management; Charging management; Charging architecture

3GPP TS 32.299: 'Telecommunication management; Charging management; Diameter charging

3GPP TS 23.380: 'IMS Restoration Procedures'.

3GPP TS 22.153: 'Multimedia Priority Service'.

IETF draft-ietf-dime-ovli-02: "Diameter Overload Indication Conveyance".

Definitions and abbreviations

One example of an AF is the P-CSCF of the IM CN subsystem.

3GPP TS 29.214 version 12.5.0 Release 12

ETSI TS 129 214 V12.5.0 (2014-10)

One example of an application session is an IMS session.

Application Detection and Control