The AM5766 is a five-channel motor driver IC used in DVD players. It contains two voltage regulators, a comparator, and drivers for the spindle motor, sled motor, focus actuator, tracking actuator, and tray motor. The IC has protections like thermal shutdown and mute mode. It can drive a variety of motors and actuators with adjustable output levels and polarity.
The AM5766 is a five-channel motor driver IC used in DVD players. It contains two voltage regulators, a comparator, and drivers for the spindle motor, sled motor, focus actuator, tracking actuator, and tray motor. The IC has protections like thermal shutdown and mute mode. It can drive a variety of motors and actuators with adjustable output levels and polarity.
The AM5766 is a five-channel motor driver IC used in DVD players. It contains two voltage regulators, a comparator, and drivers for the spindle motor, sled motor, focus actuator, tracking actuator, and tray motor. The IC has protections like thermal shutdown and mute mode. It can drive a variety of motors and actuators with adjustable output levels and polarity.
The AM5766 is a five-channel motor driver IC used in DVD players. It contains two voltage regulators, a comparator, and drivers for the spindle motor, sled motor, focus actuator, tracking actuator, and tray motor. The IC has protections like thermal shutdown and mute mode. It can drive a variety of motors and actuators with adjustable output levels and polarity.
AM5766 The AM5766 is a five-channel BTL driver IC for driving the motors and actuators such as used in DVD player and consists of two independent precision voltage regulators with adjustable range from 1.25V to 4 V. Further, a free comparator is provided for spindle motor back emf detection. It supports a variety of applications. Also, Pb free package is selectable (Please refer to Marking Identification).
Applications BTL driver for CD, CD-ROM and DVD.
Features one power OPAMP in bridge configuration. 8) Spindle driver: Single input linear BTL driver. The output structure are two power OPAMPS in bridge configuration. 10) Tray in-out driver: The DC motor driver supports forward/reverse control for tray motor. 11) 2 Built-in regulator controllers Adjustable range 1.25V ~ 4V 12) A free comparator For spindle motor back emf detection
1) Two channels are voltage-type BTL drivers for
actuators of tracking and focus. Two channels are voltage-type BTL driver for sled and spindle motors. It is also built-in one channel bi-direction DC motor driver for tray. 2) Wide dynamic range [9.0V (typ.) when Vcc1= Vcc2= 12V, at RL= 20 load]. 3) Separating power of Vcc1 and Vcc2 is to improve power efficiency by a low supply voltage for tracking, focus, and spindle. 4) Level shift circuit built-in. 5) Thermal shut down circuit built-in. 6) Mute mode built-in. 7) Dual actuator drivers: A general purpose input OP provides differential input for signal addition. The output structure is two power OPAMPS in bridge configuration. 8) Sled motor driver: A general purpose input OP provides differential input for signal addition. The output structure is
AMtek SEMICONDUCTORS
-1-
Aug 2012 V1.6
AM5766 Motor Driver ICs
Absolute maximum ratings (Ta=25C)
Parameter
Symbol Vcc1 Vcc2 Pd Topr Tstg
Supply voltage
Limits
Unit
13.5
Power dissipation *1.7 -40 ~ +85 Operate Temp range **-55 ~ +150 Storage Temp range *When mounted on a 70mm70mm1.6mm glass epoxy board. *Reduced by 13.6mW for each increase in Ta of 1 over 25. **Should not exceed Pd or ASO and Tj=150C values
@8 Load VIN=BIAS+0.2Vpp ac @1KHz VIN=BIAS+0.2Vpp ac @1KHz
VSAT1
0.7
1.1
1.5
VSAT1
0.1
VSAT2
1.0
1.55
2.2
VVtrH
7.4
9.2
11
dB
High level input voltage
Low level input voltage High level input current <Regulator> **
VIH VIL IIH
1.5 -0.3 -
180
Vcc 0.5 270
Output voltage
Vreg
3.1 1.7 -50 -25
3.3 1.8 0 0
3.5 1.9 50 25
Parameter Quiescent current Voltage for mute ON Voltage for mute OFF <Actuator drivers> Output offset voltage Maximum output voltage Voltage gain
Symbol
Unit
Conditions
P.S
mA V V
<Sled motor driver>
Output offset voltage Maximum output voltage Closed loop voltage gain <Spindle motor driver> Output offset voltage Maximum output voltage Voltage gain Gain error by polarity <Tray motor driver> Output saturation voltage 1 Output saturation voltage between F&R Output saturation voltage 2 Output adjustable gain on H side voltage
Upper + Lower saturation,
IL=200mA Output saturation voltage 1 between FWD and REV Upper + Lower saturation, IL=500mA VCTL=2V
<Tray motor driver input logic>
Output load differential
Power supply voltage differential
VRL VVCC
V V A VFWD=VREV=5V V
IL = 500mA
mV mV
IL = 0~500mA (Vcc=4.5~8V) IL = 500mA
*This device is not designed for protection against radioactive rays.
** It is based on SS8550D PNP application. Vreg can be set to other voltages with 5% deviation
AMtek SEMICONDUCTORS
-3-
Aug 2012 V1.6
AM5766 Motor Driver ICs
Pin configuration
VINFC
28
MUTE
TRB_1
27
BIAS
REGO 2
26
VINTK
VINSL+
25
TRB_2
REGO 1
24
OPOUT
FWD
23
VINLD
REV
22
GND
Vcc1
21
VCTL
VOTR-
20
OPIN
VOTR+ 10
19
Vcc2
VOSL+
11
18
VOLD-
VOSL-
12
17
VOLD+
VOFC- 13
16
VOTK-
VOFC+
15
VOTK+
14
AMtek SEMICONDUCTORS
-4-
Aug 2012 V1.6
AM5766 Motor Driver ICs
Pin description
PIN No
Pin Name
Function
VINFC
Input for focus driver
TRB_1
Connect to external transistor base
REGO2
Regulator voltage output, connect to external transistor collector
VINSL+
Input for the sled driver
REGO1
Regulator voltage output, connect to external transistor collector
FWD
Tray driver forward input
REV
Tray driver reverse input
Vcc1
Vcc for pre-drive block and power block of sled and tray
VOTR-
Tray driver output (-)
10
VOTR+
Tray driver output (+)
11
VOSL+
Sled driver output (+)
12
VOSL-
Sled driver output (-)
13
VOFC-
Focus driver output (-)
14
VOFC+
Focus driver output (+)
15
VOTK+
Tracking driver output (+)
16
VOTK-
Tracking driver output (-)
17
VOLD+
Spindle driver output (+)
18
VOLD-
Spindle driver output (-)
19
Vcc2
Vcc for power block of spindle, tracking and focus
20
OPIN
Comparator input
21
VCTL
Speed control input of tray driver
22
GND
Ground
23
VINLD
Input for spindle driver
24
OPOUT
Comparator output
25
TRB_2
Connect to external transistor base
26
VINTK
Input for tracking driver
27
BIAS
Input for reference voltage
28
MUTE
Input for mute control
Notes) Symbol of + and (output of drivers) means polarity to input pin.
(For example, if voltage of pin1 is high, pin14 is high.)
AMtek SEMICONDUCTORS
-5-
Aug 2012 V1.6
AM5766 Motor Driver ICs
Power dissipation curve :
Pd (W)
2.0
1.5
1.0
25
50
75
100
125
150
Ta()
*70mm70mm1.6mm glass epoxy board.
*De-rating is done at 13.6mW/ for operating above Ta=25
Operation notes 1) The built-in thermal shutdown circuit mutes the output current when the chip temperature reaches 175 (typ.). The hysteresis is set to 25 (typ.), so the circuit will start up again when the chip temperature falling to 150 (typ.). 2) In case mute pin voltage is under 0.5V or NC, output current is muted (except for tray motor driver). Mute pin voltage should be more than 2.0V for normal application. 3) Bias pin (pin 27) should be pulled up to more than 1.2V. In case the bias pin voltage is pulled down below 0.9V (typ.), the output current is muted. 4) Insert the bypass capacitor (~ 0.1uF ) between Vcc pin and GND pin as close as possible. 5) Heat dissipation fins are attached to the GND on the inside of the package. Make sure to connect them to the external GND.
L L OPEN OPEN Open mode L H L H Reverse mode H L H L Forward mode H H L L Brake mode Input circuit of pin6 and pin7 is designed to avoid simultaneous activation of upper and lower output tr. ; however, in order to improve reliability, apply motor forward/reverse input once through open mode. We recommend time period for open longer than 10msec. H side Output voltage on output voltage (VOL+, VOL-) varies depending on output control terminal for tray (pin21). H side output voltage is set three times (9.2dB Typ.) VTCL(pin21). And, L side output voltage is equal to output saturation voltage.
