Encoder Board MACH3

Sound Logic
Encoder Interface
4-axis parallel port encoder interface
For Mach2/3 CNC control software
Closed loop operation for Servo and Stepper systems
General Users Guide
Sound Logic
James Cullins
3454 Sprindletree Dr.
Grapevine, Tx. 76051
james_cullins@sbcglobal.net
IMPORTANT INFORMATION
Copyright and Trademarks
Copyright 2005 by Sound Logic
Disclaimers of liability
Sound Logic or James T. Cullins assumes no responsibility or liability for
any damage done to persons, PC, Geckodrives, encoders, or any other electronic
component used in conjunction with this Sound Logic Encoder Interface including
material in process. Also, loss of time or loss of work incurred. Use at your own risk.
4-axis Mach2/3 Encoder Interface

Purpose:
To interface a second PCI parallel port card from a PC running Mach software with up
to 4 individual encoder/Gecko drive inputs. Which will display the data in a DRO on a
Mach screen. Giving the user, real time data count feedback from each encoder
thereby displaying the actual position of each axis. And used with provided Macropump
for this particular purpose, alerts the user with an LED next to the offending axis and
prompts a sonalert device if used in the event of a step/count discrepancy. The
machine will be halted in feedhold status. A screen.set is also supplied that is
designed for this purpose as well and both are sent via Email with purchase.
May also be used as a stand-alone device to accept encoder data and relay it to PC for
use solely as DRO for all types of encoder data input with Mach software.
Which would require, only one PCI parallel port card, Namely, Port1. Or simply used as
8 general use inputs instead of encoder inputs. Inputs such as MPGs, Probes, OEM
triggers etc. Plus 4 software controlled onboard relays rated 125 VAC and 15 amps.
Designed to be used in conjunction with Sound Logic PC-2-route breakout board.
Operates on 115/220 volts at 60 Hz. Note: 115 volts- JP1 and JP2 are installed. 220
volts must have a jumper installed between JP1-1 to JP2-2. And existing jumpers must
be removed.
Features:
!
!
!
!
!
!
!
!
PCB
Fr4 Material
Solder mask on both sides
Silkscreen legend on topside
Plated through holes
Isolated 5 volts and grounds for the encoder interface parallel port IO
All outputs are buffered
Operational when Mach is in reset to provide the user encoder DRO position
for manual machining operations.
!
4 onboard relays rated 125 volts AC at 15 amps
to control spindle, coolant, vacuum pump etc. via M-codes in Mach software. Coupled
with Sound Logic PC to route Breakout board relay control jumpers will equal 8
controllable outputs in total.
Connectors:
J1 (X axis)
+5v Encoder +5v
XA
Encoder A
XB
Encoder B
GND Encoder Gnd
J2 (X Gecko encoder inputs)
Gnd Gecko Gnd
XA
Gecko encoder A input
XB
Gecko encoder B input
J1 (Y axis)
+5v Encoder +5v
YA
Encoder A
YB
Encoder B
GND Encoder Gnd
Note 1: Any axis J1 connector not

Used with a Gecko may be used
For general purpose inputs on
A & B terminal. The optical
Isolator associated with an input
used for general purpose may
NOT be used if anyone of the
encoder inputs are wired to
A Gecko drives encoder inputs.
All the inputs except J18-1 has
comparators on them set for
VCC to provide good noise
immunity.
J2 (Y Gecko encoder inputs)

Gnd Gecko Gnd
YA
YB
J16 General use input
J1 (Z axis)
+5v Encoder +5v
ZA
Encoder A
ZB
Encoder B
GND Encoder Gnd
J2 (Z Gecko encoder inputs)

Gnd Gecko Gnd
ZA
ZB
J1 (A axis)
+5v Encoder +5v
AA
Encoder A
AB
Encoder B
GND Encoder Gnd
J2 (A Gecko encoder inputs)
Gnd Gecko Gnd
AA
AB

Note: J18-1 does not have a comparator
associated with its input.
Connectors:
J11 Connected to second parallel port
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Pin 13
Pin 14
Pin 15
Pin 16
Pin 17
Pin 18-28
K1 relay out J12

Encoder/general purpose input see Note1
Input 1/MPG1 A to J16-2
Input 2/MPG1 B to J16-1
Input 3/MPG2 A to J17-1
Input 4/MPG2 B to J17-2
K2 relay J13
Probe/Switch (pulled up to +5v) J18-1 & J18-2 = GND
K3 relay J15
Charge pump / K4 relay J15
GND
J9 (mode)
CP uses charge pump
NCP no charge pump
A special cable can be connected (see note 2) from the MODE jumper on the encoder
interface to the MODE jumper on the Sound Logic breakout board and use the charge
pump from the breakout board for both boards.
This provides one more relay out (K4) for other uses.
J10
115 vac / 220 vac
For 115vac JP1 and JP2 are installed, use as is
For 220vac A jumper from JP1-1 to JP2-1 must be installed and the two existing
jumpers for 115 vac operation must be removed.
Note 2:
J9-1
J9-2 Red jumper between J9-1 and J9-2 is for charge pump on output 4.
J9-3 Red jumper between J9-2 and J9-3 is for no charge pump and output 4 may be
used in the same manner as output 1,2 and 3.
Typical wiring for use with a Gecko servo-drive, To use with other types
of drives such as stepper-type that require no feedback, connection to the
encoder is all that is required. And is the same basic configuration for any
type of 5VDC input device i.e. MPGs, OEM triggers, Probes etc.
Guide for installing second PCI parallel port in Windows XP

Step 1. Remove power from PC and open enclosure. Install PCI parallel
port card in any available PCI slot. Replace screw and secure PC
enclosure.
Step 2. Boot PC, Windows will automatically find the new hardware and
install a driver for it. If not, the card should come with its own software
driver on included disc. Install from the OEM disc instead.
Step 3. Mach will need to know the address of this port to communicate
with it. It will need be entered into the Config/ports and pins/ port setup
and axis selection menu in Mach software. To find the address of the
newly installed second parallel port, simply navigate to the hardware
profiles in Windows XP as follows:
Click: Start/Control Panel/System/Hardware/Device Manager/Ports (Com &
LPT)/ Printer Port LPT/ Resources.
A window like the one below should be displayed. The first line will be the
primary parallel port and the second line should correspond to the second
parallel port. The four digits in the box are what is needed to be entered
into Mach config Ports and pins menu. Mach will automatically change it
to 0x778" when the address is saved/Applied. Also on the same menu in
Mach, place a check in the Enable port
2" and Pins 2-9 as inputs boxes.
Will be one of these.
Typical screen configuration:

On the following pages are displayed screenshots with suggested configurations for
Mach software using the Sound Logic Encoder interface. Each tab of the of
Config/ports and pins screen will be covered
Note that Port#2 is enabled. Address has been entered and Pins 2-9 as inputs has
also been enabled. Kernel speed is based on each users particular demands.
Motor Outputs:
2nd port address entered here.
The following screen is a configuration for use with the Sound Logic Breakout Board. If
another breakout/distribution device is used your configuration may differ. Note that
active low may be opposite also depending your particular configuration. All axiss
used must be enabled.
Input Signals:
Below are two depictions of the same tab and screen. The upper screen depicts the
port and pin selection for limits and may also be used as general purpose inputs. And
pertains to the Sound Logic Breakout Board. Note that port two is entered in the lower
screenshot. This pertains to the Encoder interface. Port 1 deals with the Breakout board
and Port 2 is associated with the Encoder interface.
Output Signals:
Output signals are depicted below. Note which are enabled and which pins are selected
and their respective ports. These will control auxiliary devices such as spindle, coolant,
pumps, etc. The encoder interface has 4 relays on board rated at 125 vac and 15 amps.
The Sound Logic Breakout board requires a solid state relay to be used with each of its
outputs. Note on Charge pump J-9 mode, See page 5 to free up one of the outputs for
other uses.
Encoder MPGs:
In the screen below, Port 2, proper pin number and steps per unit must be entered. The
steps per unit will be the same as in motor tuning menu. Or simply the CPR in
quadrature of the encoder device times the pitch lead of the ballscrew. Again,
depending on your particular configuration. If the DRO reads in opposite, simply swap
encoder A&B pins. If encoder data is displayed on an incorrect DRO simply swap with
the correct encoder entry. Example: If Encoder 3 is displayed on Encoder 2, and 2 on 3,
swap with one another.
Spindle Setup:
Below is the spindle setup menu. Note that the Disable spindle relays and Disable
flood/Mist relays are unchecked and the proper output numbers are selected. And are
the only entries relevant to the encoder interface on this menu.
Mill options: (not shown)

The last tab in the Ports and Pins configuration covers digitizing and THC selections.
And there are no relevant entries to the Encoder Interface.
Encoder screenset for Mach3:

Below is a screenshot of the encoder screenset for Mach3. The software DROs
(shown) and the encoder DROs (on settings page) are monitored and in the event that
the two are out of synchronization with one another, The machine is halted in
feedhold, an LED next to that axis flashes and a sonalert if used sounds an audible
alarm. The Sync key to the left of the offending axis may be pressed and this will
update the software DRO in relation to the encoder DRO, and ultimately machine
position, clearing the fault. Jogging is not affected by a discrepancy/fault and allows the
user to reposition machine if necessary before clearing fault. The max allowable error
is entered on the settings page as well.
Accompanying this screenset is one special screen for manual operation which
basically consists of three large DROs that read encoder data while Mach software is in
reset or for those who wish to use the Encoder Interface in conjunction with Mach as a
simple DRO for all types of measuring applications and data collection.
Essentially, A PC running Mach, the Encoder Interface and up to 4 encoders will
produce a 4 axis DRO for all types of machines. Plus, 4 software controlled relay
outputs.
The possibilities and uses of the Encoder Interface are virtually unlimited. Any input
device that operates on 5vdc and has a return signal of at least 2.5 vdc may be used.

Encoder Board MACH3

Uploaded by

Copyright:

Available Formats

Encoder Board MACH3

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Encoder Board MACH3

Uploaded by

Copyright:

Available Formats

What is the purpose of the 4-axis Mach2/3 Encoder Interface?

What features does the Encoder Interface have?

Sound Logic

4-axis Mach2/3 Encoder Interface

Note 1: Any axis J1 connector not

J2 (Y Gecko encoder inputs)

J16 General use input

J17 General use input

J2 (Z Gecko encoder inputs)

J18 General use input

K1 relay out J12

Guide for installing second PCI parallel port in Windows XP

Will be one of these.

Typical screen configuration:

2nd port address entered here.

Mill options: (not shown)

Encoder screenset for Mach3:

You might also like