Acoustic Treatment Do It Yourself
Acoustic Treatment Do It Yourself
Acoustic Treatment Do It Yourself
by Ethan Winer
Prepared by: Deady on da Beatz
http://www.myspace.com/deadyondabeatz
INTRODUCTION
I've been very pleased to see the current
growing interest in acoustic treatment. Even
as recently as five years ago, it was rare to
read a magazine article or newsgroup
posting about acoustics, bass traps,
diffusors, room modes, and so forth. Today
such discussions are common. And well
they should be - the acoustics of a
recording or listening room are arguably
more important than almost anything else!
This article explains the basic principles of acoustic treatment. Some of the
material is taken from my bass traps plans published in Electronic Musician
magazine, some is from my company's web site, and some is from my postings
in audio newsgroups. However the vast majority is new content that does not
appear anywhere else. I have consolidated this information here to provide a
single comprehensive source that is free of commercial references. My goal is to
offer advice that is complete and accurate, yet easy to understand using common
sense explanations instead of math and formulas. Although many books about
recording studio and listening room acoustics are available, most of the better
ones are too technical for the average audio enthusiast to understand without
effort. And you'd need to purchase and read many books to learn a few relevant
items from each. Top
Please understand that I am not a degreed acoustician or studio architect.
However, I am very experienced in acoustic treatment, and particularly in bass
traps. The recommendations described here are the result of my own personal
experience and should not be taken as the final word. Although this article is
intended mainly for audio engineers and home recordists, all of the information
applies equally to home theaters, small churches and auditoriums, and other
rooms where high quality reproduction of audio and music is required.
This text will surely expand as I learn more. And as people ask me questions or
request elaboration, I will incorporate the answers and additions here. Also, there
is a growing list of newer acoustics articles on the Articles page of my company's
web site you can browse through. If you have questions or comments about
anything related to acoustics, please do not send me email. Rather, I prefer that
you post publicly in my EQ Magazine Acoustics forum. This way the effort I put
into answering can help others, and you can benefit from the answers of others
too. Top
mounts. Sound isolation issues are beyond the scope of this article. For learning
more about isolation and the types of construction needed I recommend Home
Recording Studio: Build it Like the Pros by Rod Gervais.
Proper acoustic treatment can transform a muddy sounding room, having poor
midrange definition and erratic bass response, into one that sounds clear and
tight, and is a pleasure to work and listen in. Without effective acoustic treatment,
it is difficult to hear what you're doing, making you work much harder to create a
good mix. In a home theater, poor acoustics can make the sound less clear,
harder to localize, and with an uneven frequency response. Even if you spent
many thousands of dollars on the most accurate loudspeakers and other
equipment available, the frequency response you actually realize in an untreated
room is likely to vary by 30 dB or even more. Top
There are two basic types of acoustic treatment - absorbers and diffusors. There
are also two types of absorbers. One type controls midrange and high frequency
reflections; the other, a bass trap, is mainly for low frequencies. All three types of
treatment are usually required before a room is suitable for making mixing
decisions and for serious listening.
Many studio owners and audiophiles install acoustic foam all over their walls,
mistakenly believing that is sufficient. After all, if you clap your hands in a room
treated with foam (or fiberglass, blankets, or egg crates), you won't hear any
reverb or echoes. But thin treatments do nothing to control low frequency reverb
or reflections, and hand claps won't reveal that. Basement studios and living
rooms having walls made of brick or concrete are especially prone to this
problem - the more rigid the walls, the more reflective they are at low
frequencies. Indeed, simply building a new sheet rock wall a few inches inside an
outer cement wall helps to reduce reflections at the lowest frequencies because
a sheet rock wall that flexes also absorbs a little.
You may ask why you need acoustic treatment at all, since few people listening
to your music will be in a room that is acoustically treated. The reason is simple:
All rooms sound differently, both in their amount of liveness and their frequency
response. If you create a mix that sounds good in your room, which has its own
particular frequency response, it is likely to sound very different in other rooms.
For example, if your room has a severe lack of deep bass, your mixes will
probably contain too much bass as you incorrectly compensate based on what
you are hearing. And if someone else plays your music in a room that has too
much deep bass, the error will be exaggerated, and they will hear way too much
deep bass. Therefore, the only practical solution is to make your room as
accurate as possible so any variation others experience is due solely to the
response of their room. Top
DIFFUSORS AND ABSORBERS
Diffusors are used to reduce or eliminate repetitive echoes that occur in rooms
having parallel walls and a flat ceiling. Although there are different philosophies
about how much natural reverberation recording studios and listening rooms
should have, all professional studio designers agree that periodic reflections
caused by parallel walls are best avoided. Therefore, diffusion is often used in
addition to absorption to tame these reflections. Such treatment is universally
accepted as better than making the room completely dead by covering all of the
walls with absorbent material. For me, the ideal listening room has a mix of
reflective and absorptive surfaces, with no one large area all live or all dead
sounding. Understand that "live" and "dead" as described here concern only the
mid and upper frequencies. Low frequency treatment is another matter entirely,
and will be described separately.
The simplest type of diffusor is one or more sheets of plywood attached to a wall
at a slight angle, to prevent sound from bouncing repeatedly between the same
two walls. Alternatively, the plywood can be bent into a curved shape, though
that is more difficult to install. In truth, this is really a deflector, not a diffuser, as
described in more detail below. However, a deflector is sufficient to avoid flutter
echoes between parallel surfaces.
The photo below shows a curved deflector a friend and I built for the control room
in his home recording studio. It is placed opposite the control room window and is
exactly the same size as the window (six by three feet) to maintain symmetry in
the room. If you build a deflector like this, be sure to pack fluffy fiberglass in the
air space behind the wood to keep the cavity from resonating. Ideally, the amount
of curve should be greater than shown here, with the center of the panel farther
from the wall. My friend already had some 3/8-inch plywood so we used that, but
it was very difficult to bend. Had we used 1/4-inch plywood it would have bent
more easily, letting us increase the amount of curving. Top
Real diffusor designs use an irregular surface having a complex pattern to scatter
the sound waves even more thoroughly. Yet another type, shown below, uses
chambers having different depths. Note that for diffusion to be effective, you
need to treat more than just a few small areas. When walls are parallel, adding
diffusion to only a small percentage of the surface area will not reduce
objectionable echoes nearly as well as treating one or both walls more
completely. Top
Photo courtesy of
RealTraps.
Again, the angled and curved walls described earlier are deflectors, not diffusors.
A true diffusor scatters sound waves in different directions based on their
frequency, rather than merely redirecting all waves in the same direction. This is
an important distinction because a flat surface that is angled or curved still
fosters the boxy sounding response peaks and dips known as comb filtering. A
real diffusor avoids direct reflections altogether, and thus has a much more open,
transparent, and natural sound than a simple flat or curved surface. Besides
sounding less colored than an angled or curved wall in a control room, diffusors
serve another useful purpose in recording rooms: they can reduce leakage
between instruments being recorded at the same time. Where an angled wall
simply deflects a sound - possibly toward a microphone meant to pick up another
instrument - a diffusor scatters the sound over a much wider range. So whatever
arrives at the wrong microphone is greatly reduced in level because only a small
part of the original sound arrived there. The rest was scattered to other parts of
the room.
Unfortunately the better commercial diffusors are not cheap. So what are some
alternatives for the rest of us? Aside from the skyline type diffusors, which are
sometimes made of plastic and sold for not too much money, you can make a
wall either totally dead or partially dead. For someone with a very small budget,
making the rear wall of a control room totally dead may be the only solution. At
least that gets rid of flutter echoes between the front and rear wall, though at the
expense of sounding stuffy and unnatural. But it's better than the hollow boxy
sound you get from a plain flat reflective surface. Another option is to make the
rear wall of a control room partially reflective and partially absorbent. You can do
this by making the wall totally dead, and then covering it with thin vertical strips of
wood to reflect some of the sound back into the room. If you vary the spacing
from strip to strip a little, you'll reduce the coherence of the reflections a little
which further improves the sound.
Fast repetitive echoes - also called flutter echoes - can color the sound in the
room and cause an emphasis at frequencies whose wavelengths correspond to
the distance between the walls, and between the floor and ceiling. Flutter echoes
are often identified as a "boing" sound that has a specific pitch. If you clap your
hands in a live room or an empty stairwell or tunnel, you can easily hear the tone.
If the room is large, you'll probably notice more of a rapid echo rat-a-tat-tat effect
- the "flutter." Smaller rooms resonate at higher frequencies, so there you are
more likely to hear a specific tone that continues even after the original sound
has stopped. This effect is called ringing. Besides the obvious ill effects caused
by the echoes, ringing creates an unpleasant sonic signature that can permeate
recordings made in that room and negatively affect the sound of everything
played through loudspeakers in that room. Top
Note that echo, flutter echo, and ringing are intimately related, so the delay time
and pitch always depends on the distances between opposing surfaces. With
small spacings the flutter echo's pitch is directly related to the distance. I have a
long stairwell in my home with a spacing of 36.5 inches between walls. When I
clap my hands loudly I hear a distinct tone at the F# whose pitch is about 186 Hz,
and the half wavelength for 186 Hz is 36.5 inches. But with larger distances you
may hear a higher frequency than the spacing would indicate, depending on what
sound source excites the echoes. For example, when you clap your hands or
otherwise excite a room with only midrange frequencies, the only resonances
that can respond are also at mid/high frequencies. So if the distance between
parallel walls fosters a resonance at, say, 50 Hz, you might hear 200 Hz, or 350
Hz, when you clap your hands.
Like diffusion, midrange and high frequency absorption helps minimize echoes
and ringing. But unlike diffusion, absorption also reduces a room's reverb time.
This makes the sound clearer and lets you hear better what is in the recording by
minimizing the room's contribution. For example, if you make mixing decisions in
a room that is too reverberant, you will probably add too little reverb electronically
because what you hear includes the room's inherent reverb. Likewise, if the room
is overly bright sounding due to insufficient absorption, your mixes will tend to
sound muffled when played on other systems because the treble adjustments
you make will be incorrect. Therefore, diffusion is used to avoid flutter echo,
ringing, and comb filtering, but without reducing the room's natural ambience.
Low frequency absorbers - bass traps - can be used to reduce the low frequency
reverb time in a large space, but they are more commonly used in recording
studios and listening rooms to reduce modal ringing and flatten the frequency
response in the bass range. This is especially true in smaller rooms where a poor
low frequency response is the main problem. In fact, small rooms don't really
have reverb at all at low frequencies. Rather, ringing at the room's individual
Material
125 Hz
250
Hz
500
Hz
1000
Hz
2000
Hz
4000
Hz
NRC
Owens-Corning 703
0.17
0.86
1.14
1.07
1.02
0.98 1.00
Owens-Corning 705-FRK
0.60
0.50
0.63
0.82
0.45
0.34 0.60
0.11
0.30
0.91
1.05
0.99
1.00 0.80
Table 1: Absorption coefficients of 703, 705-FRK, and a popular brand of sculpted acoustic foam
at different frequencies. All material is two inches thick and applied directly to a wall. This data
was obtained from the respective manufacturer's published literature.
It's not difficult to understand why 705 fiberglass is so much more absorbent than
typical sculpted foam at low frequencies. Besides the fact that sculpted foam has
about half the mass of solid foam due to material being removed to create the
irregular surface, another consideration is density. According to test data
published by several manufacturers of rigid fiberglass and rock wool, the denser
types absorb more at low frequencies. The data published by Johns-Manville for
their line of rigid fiberglass shown below is one example. Acoustic foam has a
density of less than 2 pounds per cubic foot (pcf) compared to 705 fiberglass
which has a density of 6 pcf.
My own tests in a certified acoustics lab confirm this, showing denser types of
rigid fiberglass absorb as much as 40 percent more than less dense types at 125
Hz and below. More recently I performed THIS series of measurements in my
company's test lab, which shows the relationship between density and low
frequency performance even more conclusively. Regardless of the reason, there
is no disputing that for a given panel size and thickness, 705-FRK is substantially
more effective at low frequencies than the same thickness of typical acoustic
foam. However, it is important to understand that a material's density is but one
contributor to its effectiveness as an absorber. Obviously, if the density is made
too high the material will reflect more than it absorbs, so it's a mistake to
conclude that higher densities are always better. For this reason, test data must
be the final arbiter of a product's effectiveness. Top
As the data above clearly shows, 6 pcf rigid fiberglass panels absorb substantially more at low frequencies
than less dense 3 pcf material.
One important way to improve the low frequency performance of any absorbent
material - besides making it thicker - is to space it away from the wall or ceiling.
For a given material thickness, increasing the depth of the air gap lowers the
frequency range it absorbs. For example, 703 that is two inches thick and
mounted directly against a wall has an absorption coefficient of 0.17 at 125 Hz.
Spacing the same material 16 inches away from the wall increases that to 0.40 a nearly three-fold improvement. Of course, few people are willing to give up that
much space in their rooms! And even very thick (four inch) 705-FRK with a onefoot gap will not absorb the lowest frequencies as well as a purpose-built bass
trap which is optimized for that purpose. Bass traps, absorption coefficients, and
spacing of absorbent material will be described separately and in more detail
later. Top
IS "RIGID FIBERGLASS" AN OXYMORON?
There is some confusion about the term "rigid fiberglass" because it is not really
rigid like a piece of wood or hard plastic. Rather, the term rigid is used to
differentiate products such as 703 from the fluffy fiberglass commonly used for
Now that you know what rigid fiberglass is, where the heck do you buy it? You
probably won't find it at your local hardware store or lumber yard, but many
insulation suppliers stock it or can order it. Start by looking in your telephone
directory under Insulation and also Heating / Air Conditioning Suppliers. You can
find the name of an Owens-Corning dealer near you by calling 800-GET-PINK
(800-438-7465) or from the Locator page on the Owens-Corning web site. Other
companies, such as Knauf, Armstrong, and Delta, make similar products, and
they often cost less than fiberglass from Owens-Corning. You can contact them
directly to find a distributor near you. In the interest of completeness, here are
some other manufacturers that make similar products: Johns-Manville,
CertainTeed, Roxul, Ottawa Fibre, and Fibrex. Top
When assessing rigid fiberglass, it is important to know its density so you can
compare equivalent products. Owens-Corning 703 has a density of about three
pounds per cubic foot (45 kilograms per cubic meter), and 705 is about six
pounds per cubic foot (90 kilograms per cubic meter). Therefore, products from
other companies that have a similar density will have similar absorption
characteristics at the same frequencies. Note that some companies call their
products mineral wool, mineral fiber, or rock wool, but acoustically they are
equivalent to fiberglass.
Rigid fiberglass is great stuff, and you can cut it fairly easily with a razor knife, but
it's not very pleasant to work with because the fibers can make your skin itch.
While handling it you should wear work gloves, and you won't be too cautious if
you also wear a dust mask. The usual way to mount rigid fiberglass to a wall is
with sheet rock screws and large diameter washers with a small hole, often
called fender washers. These washers are needed to prevent the screw heads
from pulling through the fiberglass. Fender washers are available at Home Depot
and other hardware stores. If your wall is made of cement or brick, you can
instead use construction glue like Liquid Nails to attach small strips of wood to
the wall, and then screw the fiberglass to the strips. Since fiberglass works better
when spaced away from a wall or ceiling, wood strips make sense even when
you are able to screw directly into the wall. Top
Once the fiberglass is attached to the wall, you can build a wooden frame
covered with fabric and place the frame over the fiberglass for appearance. If
that's too much work, you can cut pieces of fabric and staple them to the edges
of the wood strips. Nearly any porous fabric is appropriate, and one popular
brand is Guilford type FR701. Unfortunately, it's very expensive. One key feature
of FR701 is that it's made of polyester so it won't shrink or loosen with changes in
humidity when stretched on a frame. But polyester is a common material
available in many styles and patterns at any local fabric store. Another feature of
FR701 is that it's one of the few commercial fabrics rated to be acoustically
transparent. But since you're not using it as speaker grill cloth to place in front of
a tweeter, that feature too is not necessary.
Shiny fabrics having a tight weave should be avoided because they reflect higher
frequencies. The standard test for acoustic fabric is to hold it to your mouth and
try to blow air through it. If you can blow through it easily, it will pass sound into
the fiberglass. Burlap and Muslin are two inexpensive options, but nearly any soft
fabric will work and also keep the glass fibers safely in place. Top
BASS TRAPS - OVERVIEW
The most common application of bass traps in recording studios and control
rooms is to minimize standing waves and acoustic interference which skew the
room's low frequency response. (See the sidebar, Why They're Called Standing
Waves.) As you can see in Figure 1 below, acoustic interference occurs inside a
room when sound waves bounce off the floor, walls, and ceiling, and collide with
each other and with waves still coming from the loudspeaker or other sound
source. Left untreated, this creates severe peaks and dips in the frequency
response that change as you move around in the room. At the listening position,
there might be near-total cancellation centered at, say, 100 Hz, while in the back
of the room, 100 Hz is boosted by 2 dB but 70 Hz is partially canceled. Top
Here, a positive wave front from the loudspeaker (left) is reflected off the rear
wall on the right, and the reflection collides with other waves that continue to
emanate from the loudspeaker. Depending on the room dimensions and the
wavelength (frequency) of the tones, the air pressure of the reflected waves
either adds to or subtracts from the pressure of the waves still coming from the
speaker. Worse, different locations in the room respond differently, with a boost
at some frequencies and a reduction at others. When waves combine in phase
and reinforce each other, the increase in level can be as much as 6 dB. But when
they combine destructively, the dip in response can be much more severe. Level
reductions of 25 dB or more are typical in untreated rooms, and near-total
cancellation at some frequencies and locations is not uncommon. Further, most
rooms have many peaks and dips throughout the entire bass range, not just at
one or two frequencies. Figure 2 below shows the frequency response of the 10by 16-foot untreated control room at a friend's studio. Note the large number of
ripples, and their magnitude, all within just one octave! Top
Figure 2: Your worst nightmare? Yes, this response really is typical for an untreated
small room!
The action of sound waves colliding and combining in the air is called acoustic
interference, and this occurs in all rooms at all low frequencies - not just those
related to the room's dimensions. The only thing that changes with frequency is
where in the room the peaks and nulls occur. The principle is identical to how
phaser and flanger effects work, except the comb filtering happens acoustically in
the air. Top
The only way to get rid of these peaks and dips is to avoid, or at least reduce, the
reflections that cause them. This is done by applying treatment that absorbs low
frequencies to the corners, walls, and other surfaces so the surfaces do not
reflect the waves back into the room. A device that absorbs low frequencies is
called a bass trap. Although it may seem counter-intuitive, adding bass traps to a
room usually increases the amount of bass produced by loudspeakers and
musical instruments. When the cancellations caused by reflections are reduced,
the most noticeable effect is increasing the bass level and making the low
frequency response more uniform. As with listening rooms, bass traps are also
useful in studio recording rooms for the same reasons - to flatten the response of
instruments captured by microphones and, with large studios, to improve the
acoustics by reducing the low frequency reverb decay time which makes the
music sound more clear.
For recording engineers, problems caused by standing waves and acoustic
interference are often first noticed when you realize your mixes are not
"portable," or do not "translate" well. That is, songs you have equalized and
balanced to sound good in your control room do not sound the same in other
rooms. Of course, variations from different loudspeakers are a factor too. But
bass frequencies are the most difficult to judge when mixing because acoustic
interference affects them more than higher frequencies. Another problem is that
the level and tone quality of bass instruments vary as you walk around the room.
The sound is thin here, too bassy over there, yet not accurate anywhere. Indeed,
even if you own all the latest and most expensive recording gear, your mixes will
still suffer if you can't hear what's really happening in the low end. Aside from
portability concerns, it's very difficult to get the bass instrument and kick drum
balance right when acoustic interference and modal ringing combine to reduce
clarity. And when every location in the room has a different low-end response,
there's no way to know how the music really sounds. Top
Many people wrongly believe that using near-field monitor speakers avoids the
need for acoustic treatment. In truth, even with small loudspeakers playing softly,
acoustic interference still causes standing waves - the imperfect frequency
balance is exactly the same but at a lower level. Although higher frequency
reflections and echoes are proportionately reduced as you get closer to the
loudspeaker, the skewed frequency response caused by low frequency
reflections remains. Likewise, adding a subwoofer will not fix problems that are
due to poor room acoustics. While a subwoofer can be useful to compensate for
inadequate loudspeakers, it will not solve the problem of an irregular response
caused by acoustic interference. In fact, a subwoofer often makes matters worse
by compounding and hiding the real problem.
Another common misconception is that equalization can be used to counter the
effects of acoustic problems. But since every location in the room responds
differently, no single EQ curve can give a flat response everywhere. Over a
physical span of just a few inches the frequency response can vary significantly.
Even if you aim to correct the response only where you sit, there's a bigger
problem: It's impossible to counter very large cancellations. If acoustic
interference causes a 25 dB dip at 60 Hz, adding that much boost with an
equalizer to compensate will reduce the available volume (headroom) by the
same amount. Such an extreme boost will increase low frequency distortion in
the loudspeakers too. And at other room locations where 60 Hz is already too
loud, applying EQ boost will make the problem much worse. Even if EQ could
successfully raise a null, the large high-Q boost needed will create electrical
ringing at that frequency. Likewise, EQ cut to reduce a peak will not reduce the
peak's acoustic ringing. EQ cannot always help at higher frequencies either. If a
room has ringing tones that continue after the sound source stops, EQ might
make the ringing a little softer but it will still be present. However, equalization
can help a little to tame low frequency peaks (only) caused by natural room
resonance, as opposed to peaks and nulls due to acoustic interference, if used in
moderation. Top
Yet another common misconception is that small rooms cannot reproduce very
low frequencies, so they're not worth treating at all. A popular (but incorrect)
theory is that very low frequencies require a certain minimum room dimension to
"develop," and so can never be present at all in smaller rooms. The truth is that
any room can reproduce very low frequencies, as long as the reflections that
cause acoustic cancellations are avoided. When you add bass trapping, you are
making the walls less reflective at low frequencies, so sound that hits a wall or
ceiling will be absorbed instead of reflected. The net result is exactly the same as
if the wall was not there at all - or as if the wall was very far away - whatever
does come back is greatly attenuated due to distance and, therefore, not loud
enough to cause as much cancellation. See the sidebar Big Waves, Small
Rooms for more elaboration on this topic.
Some people mix using headphones in an attempt to avoid the effects of their
room. The problem with headphones is that everything sounds too clear and
present, making it difficult to find the ideal volume for some tracks. When
listening through headphones, a lead vocal or solo instrument can be heard very
clearly, even if it is quiet, so you'll tend to make it lower in the mix than it should
be. Likewise, it's difficult to assess the amount of reverb and echo being added
electronically when using headphones.
Note that standing waves and acoustic interference also occur at higher
frequencies, such as sustained clarinet or flute tones. You can hear the effect
and identify the problem frequencies and locations fairly easily by playing sine
waves (not too loudly!) through your loudspeakers. This is also a good way to
assess how important bass traps are for your particular studio and control rooms.
If you have SoundForge, WaveLab, or a similar audio editor program, it's simple
to create sine wave files at different low frequencies for testing. Special CDs that
contain various tones and pink noise suitable for room testing and analysis are
also commonly available. To determine the severity of low frequency problems,
play different sine waves one at a time through your monitors, and then slowly
walk around the room. It will be very obvious at which frequencies the peaks and
valleys occur, and where they cause the most harm. There's no point in playing
frequencies below what your speakers can produce cleanly - I suggest 60 Hz, 80
Hz, 100 Hz, and so forth through maybe 200-300 Hz. If you have a computer
connected to your loudspeakers, you can download the NTI Minirator program,
which generates a variety of useful audio test signals. Top
Besides helping to flatten the low frequency response, bass traps serve another
purpose that is equally important: They reduce the modal ringing that causes
some bass notes to sustain longer than others, which harms clarity. The ETF 3D
"waterfall" graph below shows the modal ringing in my 16'2" by 11'6" by 8' test
lab. Both graphs show not only the low frequency response (the "back wall" of
the graph), but also the bandwidth of each room mode and its decay time. As you
can see, adding bass traps lowers the Q of modal peaks (widens their
bandwidth) and also reduces their decay time. When the bandwidth of the modes
is widened individual bass notes stick out less than other, adjacent notes. This
solves the problem commonly known as "one note bass."
The other change is the large reduction in ringing time (the "mountains" come
forward over time). Without traps, some bass notes ring out for as long as 1/3 of
a second, so they muddy other subsequent bass notes. After adding bass traps
the ringing time is cut in half or even less, except at the lowest mode which in this
room is about 35 Hz. But even at 35 Hz there's a noticeable, if slight,
improvement in bandwidth and decay time.
This ETF graph shows how bass traps reduce ringing by making it decay faster and lowering the
Q of the resonances.
Generally speaking, most rooms need as many bass traps as you can fit and
afford. Although it is definitely possible to make a room too dead at midrange and
high frequencies, you probably cannot have too much low frequency absorption.
The effectiveness of bass traps is directly related to how much of the room's total
surface area you treat, which includes the walls, floor, and ceiling. That is,
covering thirty percent of the surface with bass traps reduces low frequency
reflections far more than covering only five percent. It would be great to invent a
magical acoustic vacuum cleaner that could suck the waves out from the air. But,
alas, the laws of physics do not work that way. At the minimum I recommend
placing bass traps in all of the corners. For even better results, put additional
traps on the walls and optionally on the ceiling.
FIBERGLASS BASS TRAPS
There are a number of ways to create a bass trap. The simplest and least
expensive is to install a large amount of thick rigid fiberglass, spacing it well away
from the wall or ceiling. As noted earlier, 705-FRK that is four inches thick and
spaced 16 inches away from the wall can be quite effective to frequencies below
125 Hz. But many rooms have severe problems far below 125 Hz and losing
twenty inches all around the room for thick fiberglass and a large air space is
unacceptable to most studio owners and audiophiles. Fortunately, more efficient
bass trap designs are available that are much smaller. However, studios on a
tight budget can apply rigid fiberglass in the room corners as shown in Figure 3a
and lose only the small amount of space in the corners. Since bass builds up the
most in the corners of a room, this is an ideal location for any bass trap. Top
Figure 3a shows the corner viewed from above, looking down from the ceiling.
When the rigid fiberglass is mounted in a corner like this, the large air gap helps
it absorb to fairly low frequencies. For this application 705-FRK is better than 703
because the goal is to absorb as effectively as possible at low frequencies.
However, you can either absorb or deflect the higher frequencies by facing the
paper backing one way or the other, to better control liveness in the room. Using
705 fiberglass that is two inches thick does a good job, but using four inches
works even better. Note that two adjacent two-inch panels absorb the same as
one piece four inches thick, so you can double them up if needed. However, if
you are using the FRK type you should remove the paper from one of the pieces
so only one outside surface has paper. Top
Besides the corners where two walls meet as in Figure 3a, it is equally effective
to place fiberglass in the corners at the top of a wall where it joins the ceiling.
With either type of corner, you can attach the fiberglass by screwing it to 1x2-inch
wood strips that are glued or screwed to the wall as described previously. The
1x2 ends of these strips are shown as small black rectangles in Figure 3a above.
One very nice feature of this simple trap design is that the air gap behind the
fiberglass varies continuously, so at least some amount of fiberglass is spaced
appropriately to cover a range of frequencies.
When mounting 705-FRK directly to a wall - not across a corner - you'll achieve
more low frequency absorption if the paper covered side is facing into the room.
However, that will reflect mid and high frequencies somewhat. One good solution
is to alternate the panels so every other panel has the paper facing toward the
room to avoid making the room too dead. Panels attached with the backing
toward the wall should be mounted on thin (1/4-inch) strips of wood to leave a
small gap so the backing is free to vibrate. For fiberglass across a corner as
shown in Figure 3a, the backing should face into the room to absorb more at low
frequencies.
For a typical unfinished basement ceiling you can take advantage of the gap
between the support beams and the floor above by placing rigid fiberglass
between the beams. Short nails or screws can support the fiberglass, making it
easy to slide each piece of fiberglass into place. Then cover the fiberglass with
fabric as shown below in Figure 3b. You can optionally pack the entire cavity with
fluffy fiberglass one foot thick and you'll probably get similar results. Top
Treating a "dropped" grid ceiling is even easier: Simply lay fluffy fiberglass batts
on top of the grid, above the ceiling tiles. The thicker the fiberglass, the better.
One foot thick R38 is perfect for this if you have the space. If you don't want to
bother covering the entire ceiling that way, at least put fiberglass batts around the
perimeter to treat the important wall-ceiling corners. And since the fiberglass is
not exposed to the room and doesn't show, you don't need to cover it with fabric.
Another great and inexpensive way to make a bass trap - if you have a lot of
room - is to place bales of rolled up fluffy fiberglass in the room corners. These
bales are not expensive, and they can be stacked to fill very large spaces. Better
still, they are commonly available and you don't even have to unpack them! Just
leave the bales rolled up in their original plastic wrappers, and stuff them in and
near the room corners wherever they'll fit. Stack them all the way up to the ceiling
for the most absorption.
OPTIMIZING THE AIR GAP
While increasing the depth of the air gap does indeed lower the frequency range
absorbed, for thinner panels it can also reduce the absorption at some higher
bass frequencies. The maximum amount of absorption for a given frequency
occurs when the air gap is 1/4 the wavelength for that frequency. Figure 4 below
shows the velocity of a sound wave, which is greatest as it transitions through
zero. When it reaches the top or bottom of the cycle, the velocity is minimum, but
the pressure is maximum. Because the velocity is greatest 1/4 wavelength from a
boundary, more energy is present to force the waves through the absorbent
material.
The reason an absorbent material like fiberglass works better when spaced away
from a surface is that sound waves passing through it have a greater velocity
there. As a wave approaches a boundary, such as a wall, the velocity is reduced,
and when it finally hits the boundary, the velocity is zero. Imagine a cue ball as it
approaches the side rail on a pool table. The ball could be travelling 100 miles
per hour, but at the exact point where it hits the rail the ball is not moving at all.
Without motion there's no energy to be absorbed.
Likewise, fiberglass placed exactly at a rigid boundary does nothing because the
air particles are not moving there. And since there's no velocity, the fiberglass
has very little effect. As fiberglass is spaced further from the wall, the air particles
passing through it have greater velocity. They are slowed down as they pass
through the fiberglass, which converts the sound energy into heat therefore
absorbing some of the sound. Top
As you can see in Figure 5 above, borrowed from Alton Everest's Master
Handbook of Acoustics, absorption for a given gap depth is maximum at 1/4
wavelength multiples - in this case starting at around 250 Hz. It then falls off at a
higher frequency where the gap depth equals 1/2 wavelength. It rises again when
the gap matches 3/4 of the length of the next higher frequency, and so forth. This
irregular absorption is most severe with thin absorbing materials, and gradually
diminishes as the material is made thicker. You can avoid the reduction in
absorption either by using thicker rigid fiberglass, or by filling the entire gap with
material instead of using only a thin piece spaced away from the wall or ceiling.
When the entire depth is filled, material is available to absorb all of the
frequencies whose 1/4 wavelengths fall within that depth. Top
Although I promised not to use any math, I promise that the following simple
formula is the only exception. To determine the best gap depth for a given
frequency, you first need to determine the equivalent wavelength:
Wave Length in Feet = 1130 / Frequency
Then simply divide the result by 4 to get the optimum depth. So for 100 Hz the
wavelength is 1130/100 = 11.3 feet, and 1/4 of that is about 2.8 feet. The number
1130 is the approximate speed in feet per second of sound waves travelling
through air at normal room temperature and humidity.
For a given thickness of absorbent material, the ideal air gap is equal to that
thickness because it avoids a hole in the range of frequencies absorbed. For
example, if you install fiberglass that is four inches thick with a four-inch gap,
higher frequencies whose 1/4 wavelength falls within the four-inch material
thickness are absorbed regardless of the gap. And for those frequencies whose
1/4 wavelength is between four and eight inches, the fiberglass is also at the
proper distance from the wall or ceiling. This is shown below in Figure 6. Top
In practice, you don't necessarily have to measure wavelengths and calculate air
gaps, and the first few inches of space yield the most benefit. Most people are
not willing to give up two or more feet all around the room anyway, so just make
the gap as large as you can justify. If you can afford to fill the gap entirely with
material, all the better. And even though the velocity is indeed highest at 1/4
wavelength, there's still plenty at 1/8th of the wavelength too. Note that the angle
at which sound waves strike a fiberglass panel can make the panel and its air
gap appear thicker than they really are. Further, low frequency waves that strike
an absorbing panel at an angle may be absorbed less than when they strike it at
90 degrees, due to a "grazing" effect. The explanations in this section are a
simplification and are correct only for a 90 degree angle of incidence, which is
not always the case.
I should mention another popular type of absorber, the tube trap, which is
available commercially and also as do-it-yourself plans on various web sites.
Although these are often referred to as "bass traps," even the largest tube
models are not very effective below about 100 Hz, and the smaller ones become
ineffective much higher than that. Marketing hype aside, the real absorption
mechanism in a tube trap is simply the rigid fiberglass inside. The reason a 20inch tube trap works at all down to 100 Hz is that the tube's diameter serves to
space some of the fiberglass away from the nearest boundary, which helps
extend its absorption to a lower frequency. But a tube design is no more effective
than using plain rigid fiberglass spaced similarly. Top
BETTER BASS TRAPS
Yet another type of bass trap is the Helmholtz resonator. Unlike foam, fiberglass,
and tubes fitted with fiberglass, a Helmholtz resonator can be designed to absorb
very low frequencies. This type of trap works on the principle of a tuned cavity
and is often very efficient over a narrow range of frequencies. Think of a glass
soda bottle that resonates when you blow across its opening, and you have the
general idea. Although a Helmholtz design can be very efficient, the downside is
that it works over a fairly narrow range and needs to be rather large to absorb
very low frequencies. The range can be widened by filling the cavity with
fiberglass, or by creating several openings having different sizes. One common
design uses a box filled with fiberglass with its front opening partially covered by
a series of thin wood boards separated by air spaces. This is called a slat
resonator. Another also uses a box filled with fiberglass but has a cover made of
pegboard containing many small holes. Although there is no denying that a
Helmholtz trap can be very effective, the fact that it works over a narrow range of
frequencies limits its usefulness. While it can be sized to absorb the dominant
resonant frequencies in a particular room, it cannot absorb all the other low
frequencies. And broadband absorption is needed to prevent acoustic
interference that skews the frequency response throughout the entire bass
range. Top
One of my favorite types of bass trap is the membrane absorber, also called a
panel trap because it's made with a wood front panel. One huge advantage of
membrane traps is that they do not have to be very thick to absorb very low
frequencies. Because the bass range spans about four octaves, most panel traps
are designed to work over only part of the bass range. Therefore, you will need
an equal mix of trap types, with one intended to absorb the lower bass
frequencies and the other for the higher bass range. Besides absorbing low
frequencies very well, the wood front on a panel trap is reflective at higher
frequencies. So installing enough of them to treat a room properly for low
frequency problems will not make the room too dead sounding at mid and high
frequencies.
The photo below shows eight panel traps I built for my home studio. Besides the
panels, which are painted white, there are also many 703 fiberglass absorbers
covered with tan fabric. Not shown are four more panel traps in the rear corners,
plus another four on the side walls farther back in the room. The photo shows
both types of panel traps (low-bass and high-bass), with the thinner units
absorbing the higher bass range. Since this is a fairly large room for a home
studio (18 by 34 feet), many traps are needed to cover a significant amount of
the room's surfaces. A smaller room would need fewer traps to cover the same
percentage of surface area. Top
This room has an even mix of low-bass and high-bass panel traps, and an equal number of fiberglass
absorbers to handle the midrange and high frequencies. More bass traps are in the rear of the room.
Figure 7 below shows a cut-away view of a typical wood panel membrane trap.
When a wave within the effective range of frequencies reaches the front panel,
the panel vibrates in sympathy. Since it takes energy to physically move the
panel, that energy is absorbed rather than returned into the room. The fiberglass
then damps the plywood panel so it doesn't continue to vibrate. Were the panel
allowed to vibrate freely on its own, less energy would be needed to keep it
moving, so it would absorb less. Further, a panel that continues to vibrate on its
own after the source sound stops actually generates sound similar to reverb and
the ringing effect described earlier, and obviously that is not desirable! Top
Similar to an acoustic suspension loudspeaker, panel absorbers like this one are
sealed air-tight, and the fiberglass converts the acoustic energy into heat. Note
how the fiberglass is spaced away from the back panel, which is more effective
than simply attaching it directly against the rear surface. The closer the fiberglass
is to the plywood panel, the more effectively it damps the panel's vibration. But it
is important that the fiberglass not touch the panel because that would restrict its
movement. For a panel trap to absorb as efficiently as possible, the panel must
be free to vibrate with no restriction other than the damping action of the nearby
fiberglass. Top
There are a few reasons for sealing panel traps. If there's a place for air to
escape - let's say at the seam between the front panel and the side of the box then pressure from the diaphragm as it pushes into the box will send the waves
out the leak rather than push them into the fiberglass. Another, more relevant,
reason is that a leak will let the internal pressure escape, reflecting the waves
back into the room instead of absorbing them. Think of a panel trap as equivalent
to an open window. If you cut a hole in an outside wall and cover the hole with a
piece of heavy cardboard, the cardboard will reflect mid and high frequencies but
let lower frequencies pass through. Those frequencies end up on the outside of
the wall and so are not reflected back into the room. A sealed membrane bass
trap is similar in that sound passing through the panel goes into the box and does
not come out. But the most important reason a panel trap must be sealed is
because the air inside acts as a spring, and an air leak reduces that effect.
Although mounting fiberglass across the corner of a room is best for treating
bass frequencies, panel traps work on a different principle where the gap does
not help. So with panel traps it's better to put two in each corner, flat against the
wall, because that provides twice the surface area of just one trap mounted
across the corner. Bass traps built from porous materials like fiberglass and
acoustic foam work by absorbing the sound waves as they pass through the
material. This type of trap is called a velocity absorber because it is velocity
(speed) that drives the sound wave into the absorbing material. A wood panel
trap works on an opposite principle, wave pressure, and is considered a
pressure absorber because the wave pressure is greatest at the room
boundaries. You can think of a wood panel bass trap as being a "shock
absorber" for sound waves. As a wave approaches a wall it has plenty of velocity
(the speed of sound) but no pressure. And when it hits the wall there's no longer
any velocity but now there's plenty of pressure. This is similar to driving a car into
a tree. You can be going 60 miles per hour toward the tree - lots of velocity - and
the instant you hit the tree there's no velocity but plenty of pressure! Top
AS GOOD AS IT GETS?
Okay, so how much improvement can you really expect after installing bass
traps? Unless you cover nearly all of the wall and ceiling surfaces with material
that is 100% absorbent at all problem frequencies - which is pretty much
impossible - you will still have some deviation from a perfectly flat response. But
even with a more practical amount of treatment, you can achieve far less severity
in the ripples and also increase their bandwidth so the peaks and dips are
broader, making them less damaging and less likely to affect single bass notes.
You'll probably still have peaks and dips that you can measure and identify with
sine wave tests, but the music will sound much better, and the bass levels will
vary much less around the room. The difference in frequency response of a room
with and without membrane panel bass traps is shown in Figure 8 below.
Figure 8: That's more like it! This response plot is for the same control room shown in
Figure 2 but after treatment with wood panel bass traps.
Top
dimension. Rooms with irregular shapes, such as an alcove, have more than
three sets of modes and are more difficult to calculate.
Generally speaking, larger rooms are better acoustically than smaller rooms
because the modes are spaced more closely, yielding an overall flatter response.
Acoustics experts recommend a minimum volume of at least 2500 cubic feet for
any room in which high quality music reproduction is intended. Figure 9 below
shows the modes for just one dimension - let's say the length - of two different
rooms. Here, the larger room (top) has a length of 28 feet, so the fundamental
mode frequency, which occurs at half the wavelength, is 20 Hz. Subsequent
modes, similar to harmonics of a note played by a musical instrument, occur at
20 Hz intervals. Even though this creates many little resonant peaks in the
response, the peaks are close together, so the average response is fairly flat.
And as one peak is falling, the adjacent peak is rising to help compensate and fill
in the void. (Please note that Figures 9 and 10 are approximations as drawn in a
graphics program, so the shapes of the peaks and dips are not truly accurate.)
Top
Figure 9: In a large room (top), the resonant peaks caused by modes are closer together than
those in a small room (bottom). The closer spacing yields an overall flatter response.
Now consider the length modes for the smaller room, shown at the bottom of
Figure 9. Here the first peak is at 60 Hz, which corresponds to a half wavelength
of about 9-1/2 feet. Therefore, subsequent modes occur at 60 Hz intervals
making the overall response less uniform because a wider range of frequencies
is attenuated, and more deeply, between each set of peaks. Top
Another important factor in the design of studios and listening rooms is the ratio
between the length, width, and height. The worst shape is a cube having all three
dimensions the same. A cube has the fewest number of peaks, and therefore the
greatest distance between peaks, because all three dimensions resonate at the
Figure 10: The modes for a room with ideal ratios (top) give a more even response overall than a
room with poor ratios (bottom). When the room proportions are less than ideal, some of the
natural resonances are spaced far apart while others are clustered very close together.
Besides making the overall response less uniform, uneven mode spacing can
make one note on a bass instrument louder than adjacent notes. This is much
worse than having a gentler curve created from many in-between peaks that,
even if not flat, affects a wider range of notes. The principle is similar to using EQ
to boost midrange presence in a recording - a broad boost always sounds more
natural than a narrow one. Narrow peaks tend to impart a nasal quality that
sounds like a wah-wah pedal set to a fixed point near the middle of its range.
Note that besides creating peaks in the frequency response, the modes also
determine at which frequencies the room's natural reverb is most pronounced. It
is better for a room's reverb to be even across the spectrum rather than comprise
a few dominant frequencies, which colors the sound unnaturally. So for all of
these reasons a room should have different and non-related dimensions for the
length, width, and height. When all three dimensions are the same - the worst
case - you get widely spaced resonant peaks at the fundamental frequency and
its harmonics only. With different dimensions you have more peaks at more inbetween frequencies, which taken together gives an overall flatter response. Top
There are a few "ideal" ratios of room height, width, and length that professional
studio designers agree should be used if possible. Three of these ratios,
developed by L.W. Sepmeyer, are shown in Table 2.
Height
Width
Lengt
h
1.00
1.14
1.39
1.00
1.28
1.54
1.00
1.60
2.33
Table 2: The ideal room has a ratio of height, width, and length similar to one of these.
There are other good ratios, but those shown above are the ones I see
referenced most often. Note that when a room has a suspended tile ceiling the
real height, as far as low frequencies are concerned, is to the solid surface
above the tiles. Likewise, in a basement with exposed joists the true height is to
the bottom of the floor above, not the bottom of the joists. Top
That said, I believe the importance of room modes is often overstated. You don't
want the width to be the same as the depth or an even multiple such as 10 feet
by 20 feet. But the modes just describe where the resonances will be worst.
Regardless of the room's size and shape, standing waves and acoustic
interference happen at all low frequencies. So you still need bass traps that
handle the entire range, not just the frequencies determined by the room modes.
As far as acoustic interference is concerned, the only thing that changes with
different room dimensions is where in the room the peaks and dips at each low
frequency occur.
There are many freeware and web-based room mode calculators, but all the
ones I've seen just list a table of the modes, so you still have to plot them by
hand on semi-log graph paper to get a sense of how close they are to each
other. Here is a link to ModeCalc (only 57 KB to download), a room mode
calculator I wrote that runs in DOS and Windows. It plots the first ten primary
room modes graphically so you can see how the modes are distributed and how
they relate to one another. The modes for each dimension are displayed in a
different color, and when two or more modes occur near the same frequency, the
duplicates are shown on a separate line so one does not obscure the other. The
program is easy to use, and pressing F1 displays complete instructions and
explains how to interpret the results. Since the instruction manual contains
additional explanations about room modes, it is reprinted below in the sidebar
Room Modes and ModeCalc. Top
ROOM SYMMETRY
Unless you plan to record and mix in mono only, the symmetry of your room and
loudspeaker placement are very important. If both loudspeakers are not situated
symmetrically in a room they will have a different frequency response, and your
stereo imaging will not be balanced. In a room that is longer than it is wide, it's
better to place the speakers near the shorter wall so they fire the long way into
the room as shown on the left in Figure 11 below. This puts you farther from the
rear wall where the low frequency peaks and nulls are most severe.
Figure 11: Symmetry matters! In a typical stereo mixing room, the loudspeakers are spaced equally
from the walls and corners, and form an equilateral triangle at the mix position. The arrangement
shown on the left above is better than the one on the right because it's more symmetrical within the
room. The layout on the right also suffers from a focusing effect caused by the wall-wall junction
behind the listener.
Besides positioning the loudspeakers symmetrically, you should also place your
console and chair so your ears are the same distance from each speaker.
Likewise, acoustic treatment - whether absorption or diffusion - should be applied
equally on both sides. In many home studios it is not possible to create a
completely symmetrical arrangement, but you should aim for as close to this
ideal as possible. Especially in the critical front part of the room where the first
reflections to reach your ears are those from the side walls, and from the floor
and ceiling if they're not treated with absorbent material. What happens in the
rear of the room is probably less important. Top
Although the sample rooms shown above in Figure 11 are rectangular, I prefer
angled walls and an angled ceiling because that provides deflection which
reduces flutter echoes and ringing. Some people argue that parallel walls are
preferred because you can better predict the room modes, and then treat the
inevitable flutter echoes with absorption. But as I explained earlier, simply
knowing the modes is not always that valuable, and with angled walls you can
make the average dimensions comply with the ideal ratios. Further, if a room has
parallel walls that must be treated with absorptive material to avoid echoes and
ringing, you may not be able to make the room as live as you'd like. See the
sidebar Creating a Reflection Free Zone for more related information.
A peaked ceiling is better than a flat ceiling because it avoids the echoes and
ringing that occur when the ceiling is parallel to the floor. But a peak creates a
focusing effect, much like a parabolic dish, which is less than ideal. For this
reason it's a good idea to place absorption or diffusion under the peaked portion,
as shown in the photo below.
One somewhat controversial aspect of control room design is soffit mounting the
main loudspeakers. Most home studio owners simply put their speakers on
stands, or sit them on the mixing desk, and leave it at that. But many pro studios
prefer to install the speakers into the wall so the front surface of the speaker
cabinet is flush with the wall. There are sound scientific reasons to use soffit
mounting, yet some engineers say it's not necessary or that it gives poorer
results. Those in favor of soffit mounting point out that it reduces reflections
called Speaker Boundary Interference, or SBIR, that cause peaks and dips in the
low frequency response. If a loudspeaker is out in the room away from the wall,
low frequencies from the rear of the cabinet will bounce off the wall behind it and
eventually collide with the direct sound coming from the front of the speaker.
(Even though it may not seem obvious, very low frequencies do in fact leave a
speaker cabinet in all directions.) Proponents also claim that soffit mounting
improves stereo imaging by reducing mid and high frequency reflections.
I happen to side with those in favor of soffit mounting, yet I also respect the
opinions of those who disagree. One thing nobody will dispute is that soffit
mounting requires a lot more effort! If you do use soffit mounting, please
understand that the speakers must be built into the real wall. You can't just apply
a lightweight facade around the front of the speaker cabinet and expect the same
results. Top
LIVE OR DEAD - WHICH IS BEST AND WHERE?
In a more typical room I recommend a mix of hard and soft surfaces for the walls,
with no one large area all hard or all soft. I suggest applying absorbent material
to the walls using stripes or a checkerboard pattern to alternate between hard
and soft surfaces every two feet or so. This makes the room uniformly neutral
everywhere. You can make the spacing between absorbent stripes or squares
larger or smaller to control the overall amount of liveness. If you are using 705FRK rigid fiberglass or an equivalent product, you can cover more of the wall and
still control the liveness by alternating the direction of the paper backing. That is,
one piece of fiberglass will have the paper facing the wall to expose the more
absorbent fiberglass, and the next piece will have the paper facing out to reflect
the mid and high frequencies. In fact, when the paper is facing into the room the
lower frequencies are absorbed even better than when it is faces the wall.
Alternating hard and soft surfaces is also advisable with wood panel bass traps simply place a fiberglass absorber between each trap. You can see this
arrangement in the photo of my studio (above Figure 7), where each type of bass
trap alternates with the other type and with fiberglass panels. That is, first is a
low-bass trap, then a fiberglass panel, then a high-bass trap, then fiberglass,
then low-bass, and so forth. I'll also mention that wood panel bass traps can be
mounted horizontally when book shelves and other obstacles prevent placing
them vertically. Since the corner formed by a wall and the ceiling, or a wall and
the floor, is just as valid as any other corner, mounting a panel trap sideways
near the top or bottom of a wall is equally effective.
Of course, many studios do have large live areas, and there's nothing wrong with
that! If the room is big enough to avoid short echoes between closely spaced
walls, having an entire wall reflective can yield a very big sound. And even in
smaller rooms a hard floor with one or more bare walls can be useful. My cello
teacher, who is a total audio neophyte, blew me away with the quality of a
recording she made in her small Manhattan apartment. She recorded while
playing with her back against the corner, facing into the room, using an
inexpensive stereo mike placed a few feet in front of her cello. The key to a
realistic and present sound, especially for acoustic instruments, is capturing
some amount of ambience - even when the reverberation of a large space is not
appropriate. Top
Although it is often desirable to alternate hard and soft surfaces on the walls, I
often recommend covering the entire ceiling with absorbent material, especially if
the ceiling is low. Besides eliminating floor to ceiling flutter echoes, full absorption
can make the ceiling appear acoustically to be much higher. Most home studio
owners cringe at the thought of making their ceilings even lower than they
already are, but it really can help the sound. If you cover the entire ceiling with 2to 4-inch thick 705, suspended with strings or wires to leave an air gap, the room
will sound as if the ceiling were much higher. There's no difference between
reflections that are reduced by the greater distance of a high ceiling and
reflections from a low ceiling that are reduced by absorption. Using thick, dense
fiberglass extends the simulated increase in height to lower frequencies. Where
thin fiberglass makes the ceiling appear higher at midrange and high
frequencies, using thicker and denser fiberglass with an air gap raises the
apparent height at lower frequencies as well.
Another advantage of full absorption on a low ceiling is that it avoids the comb
filtering that occurs when miking drums and other instruments from above.
Placing microphones high over a drum set or string section puts the mikes very
close to the ceiling. If the ceiling is reflective, sound will arrive at the mikes via
two paths - the direct sound from the instrument and the same sound after being
reflected off the nearby ceiling. When the difference in distance is very small, let's
say one foot, the reflections cause many peaks and dips in the response, which
are very audible and can sound like a flanger effect. (When reflections cause a
series of peaks and dips, the effect is often called comb filtering because the
frequency response plot resembles a hair comb.) Again, reducing strong
reflections from a nearby ceiling via total absorption is acoustically identical to
having a ceiling that's infinitely high. Top
NOISE CONTROL
Reducing noise and sound leakage is beyond the scope of this article, but I will
share a few tips studio owners may find useful. If your studio has forced air
ventilation, be sure to place the microphones away from the vents while
recording. If the vents have adjustable deflectors, set them to direct the air away
from where you normally place your microphones. Better, allow the room to get
to the desired temperature before you start recording so you can turn off the
blower. You can turn it on again between takes if needed. Likewise, radiators
often make creaking sounds due to expansion and contraction as they warm up
and cool down, so use them before you start recording.
Another troublesome noise source in many studios is the fan noise from a
computer. You can buy a low noise replacement power supply from PC Power
and Cooling and other companies. Easier, buy a computer from one of the better
manufacturers because they often have much less fan noise than the cheaper
brands. My last three computers were Dells, and they have all been very quiet.
The small premium you pay for a better brand is easily gained back by not
replacing the power supply or having to build or buy a sound proof enclosure.
I also attached 703 fiberglass wrapped with fabric to the rear and underside of
my desk, as shown in the photo below (left), to absorb the fan noise rather than
reflect it into the room. Between the Dell's quiet power supply and the fiberglass,
I can record myself playing the cello or acoustic guitar while sitting in front of the
computer, with the mikes pointed right at me and the computer, and still pick up
very little noise. A second piece of 703 (right) can be placed in front of the
computer to reduce the noise even further while recording. Top
One easy way to reduce noise from a computer is to line the surrounding surfaces with absorbent material.
If you've done all you can to reduce ambient noise and it's still too loud in a
recording, consider using digital noise reduction. Many programs are available
that do a remarkable job of removing any type of steady noise - not just hiss, but
hum and air conditioning rumble too - after the fact. I use Sonic Foundry's Noise
Reduction plug-in, but other affordable programs are available that also do an
excellent job.
MORE RESOURCES
I have tried to make this article as complete as possible, but it is impossible to
cover every aspect of acoustics. Many books have been written about acoustics
and studio design, and my goal here has been to cover only the issues that are
most important to recording engineers and audiophiles. Further, acoustics is as
much an art as a science, and surely mine are not the only valid opinions.
Fortunately, the Internet offers many resources for more information including my
own Acoustics forum at EQ Magazine, John Sayer's Studio Design forum, the
SAE web site, the Acoustics newsgroup, and Angelo Campanella's Acoustics
FAQ. Perhaps the most valuable resource of all is Google, where you can find
web pages that cover nearly any topic. Top
3 dB to compensate. In practice the left and right equalizers are usually adjusted
independently, since each speaker and its location in the room may require a
different correction. Top
My personal philosophy is to avoid room equalizers because they can introduce
as many resonant peaks and valleys in the response as they remove. And as
explained in the main text, room equalization that improves the response in one
part of the room almost always makes it worse in other places. Years ago I
added a small amount of EQ cut at 400 Hz to the monitor system of my home
recording studio, to correct a measured boost at that frequency. But after a year
or so I removed the EQ because it seemed to make my mixes worse. I have
heard similar reports from other studio owners - after going to great effort and
expense to equalize their loudspeakers to make them perfectly flat, the result
was generally poor and their mixes sounded worse in other rooms instead of
better. But if you want to measure your own room just to know its response,
following are a few ways to do that.
The old fashioned way to measure the frequency response of speakers in a room
uses a pink noise signal source, a sweepable filter that passes 1/3 octave bands
one at a time, a high-quality small-diaphragm omnidirectional condenser
microphone, and a voltmeter with a decibel readout. All-in-one spectrum
analyzers are available that combine these components into a single package,
making the measurements fairly easy to perform. There are also software
programs available that use your PC's sound card to play pink noise while
recording from the microphone, and then display the room response. Top
Place the microphone at ear level where you sit while mixing. Then play the pink
noise in mono through both of your loudspeakers, loudly enough to drown out all
ambient noise by at least 30 dB. That is, the difference shown on the record level
meter should be at least 30 dB between playing the noise and not playing the
noise. Record about ten seconds of the noise from the mike onto a high quality
medium like a DAT or a computer - 16 bits at 44.1 KHz is fine. Now load the file
into SoundForge or another audio editor that offers a spectrum analyzer, and
view the results at the highest resolution offered. You can also measure each
speaker separately, if you'd like, or place the microphone in various locations in
the room to measure the response in those places. The microphone does not
have to be perfectly flat, as long as you know what its response really is and
incorporate the deviation into your measurements. If you have an expensive
mike, it probably came with a custom printed frequency response curve, and you
can add/subtract that curve from your measurements to remove the mike's
contribution to the results.
Another test uses plain sine waves, which more closely reflects real music, such
as a bass player sustaining a note on a slow ballad. The sine wave test is similar
to the test that uses pink noise, except you'll play a series of low frequencies one
at a time and read the results on a meter. Start at the lowest frequency your
Another type of absorption test places the material being tested in a device called
an impedance tube. This is a long narrow sealed chamber made of concrete or
brick in which standing waves along the length of the tube are measured with
and without the test material present. When using either test method, the
ambient temperature and humidity must be constant and known precisely, as
these affect the absorption of air and thus must be factored into the
measurements.
Labs that perform acoustic tests are certified by NVLAP, a department of the US
Government's National Institute of Standards and Technology. Testing of
acoustic materials is defined by ASTM, a US organization that establishes
standards and practices used by acousticians and their companies. By ensuring
that its members follow exactly the same rules and guidelines, materials tested to
ASTM standards in different facilities can be compared with confidence.
Most absorption measurements are taken with the test material mounted directly
to a wall. But since spacing absorbent material away from a wall improves its low
frequency performance, absorption figures that include spacing are often
included in published specifications. In this case the specs indicate the type of
mounting and also the spacing. The "A" mounting method means the material is
flat against a wall, and E-### means the material was spaced, where the number
(###) indicates the size of the air gap in millimeters. E-400 is common, which is
about 16 inches. When "E" mounting measurements are made according to
ASTM standards, a reflective skirt is applied around the edges of the material
that extends to the mounting surface. This prevents reflections from bouncing off
the mounting surface at an angle and entering the material from behind, which
would wrongly increase the absorption measurements. Top
You may notice that absorption coefficients sometimes have a value greater than
1.0. Although it is impossible for any material to absorb more than 100 percent of
the sound, measurements can yield a value greater than 1.0. The main reason
this occurs is that all material has a finite thickness, and the edges - which are
not included in the stated surface area - absorb some of the sound. So for a
piece of 703 fiberglass that is two by four feet and four inches thick, the real
surface area includes the four-inch thick edge around the material. If included in
the measurements, this would add four square feet to the stated surface area of
eight square feet - a 50 percent increase! (See the sidebar The Numbers Game
for a more detailed explanation.) But even when the edges are included in the
total surface area, values greater than 1.0 are still possible due to diffraction
effects at the material's corners. When the corners are rounded, this effect is
reduced.
As you might imagine, the fee to use a lab that performs certified acoustical
testing is high because it's very expensive to build a reverberation test room.
Such a room must have a very low ambient noise level, which requires isolated
structures, special sound proof doors, and a low air flow ventilation system.
Building a room large enough for testing very low frequencies is even more
expensive. For this reason it is rare to see absorption specifications that extend
below 100 Hz - it simply costs too much to build a room that can measure
absorption accurately below that frequency. Further, most industrial
manufacturers - the main customers of testing labs - do not need measurements
at very low frequencies. However, even when a room is certified down to only
100 Hz, it is still possible to assess relative absorption. That is, you can test
different materials at, say, 50 Hz and see which are more absorbent even if the
absolute measurements are not guaranteed accurate. Top
SIDEBAR: THE NUMBERS GAME
Acoustic products are commonly specified by their absorption coefficient. This
number ranges from zero (no absorption) to 1.0, meaning 100 percent of the
sound is absorbed. For example, an absorption coefficient of 0.5 means that half
the sound is absorbed and the other half either passes through the material or is
reflected. Since no material absorbs all frequencies by the same amount,
absorption coefficients are usually given for different frequency ranges.
Although 1.0 is the largest legitimate value possible, you may have seen higher
numbers claimed for some products. Needless to say, this causes confusion, and
makes it difficult to compare published data. Once you understanding how
absorption is measured, and how data can be manipulated - both fairly and
unfairly - you'll be able to assess room treatment products and materials more
wisely.
Acoustic absorbers are tested using methods defined by the ASTM, a US
organization that establishes standards and practices used by acousticians and
testing labs. By requiring its members to follow the same rules, materials tested
to ASTM standards in different facilities can be compared with confidence.
However, a flaw in the test method does not take into account the edges of the
material. Top
Although the edges are exposed when the material is tested, the calculation for
absorption coefficient considers only the size of the front surface, and ignores the
edges completely. For a panel that is two by four feet and four inches thick, the
edges add 50 percent to the absorbing surface during testing, yet they are
ignored in the coefficient calculation. This is further complicated because there is
no standard sample size. Since a small sample has proportionally more edge
than a larger one, a sample that's 8 by 8 feet will measure better than one that's
10 by 12 feet, even if they're the same thickness and made of the exact same
material.
In practice, multiple panels are placed adjacent to each other during testing, to
minimize the contribution of the edges. So when 2 by 4 foot panels are tested,
typically eight of them are arranged into a larger square. But even when placed
to form a single surface area of 8 by 8 feet, four-inch thick edges still inflate the
measurements by more than 16 percent. Top
This panel is 2 by 4 feet and 4 inches thick. During testing the four edges add
50 percent to the total surface area, yet they're excluded from the absorption
calculations. And when many panels are mounted adjacent on a wall, the
edges are not absorbing even though they contributed to the published
specs.
Further, most acoustic panels are meant to be installed adjacent on the wall in a
cluster. In this case the edges are not available to absorb even though they were
when the material was tested. When an entire wall is covered with four-inch thick
panels none of the edges are exposed, so the real absorption is only 2/3 what
the published numbers indicate - and those numbers were already inflated!
The same thing occurs with corner absorbers, as shown in the figure below.
Unless the vendor describes how these triangle shaped samples were grouped
during testing, there is no way to determine how much of the stated absorption is
due to the edge effect and how much is due to its effectiveness as an absorber.
Top
Foam blocks like this are meant to be mounted in a corner, stacked one above
the other from floor to ceiling. When measured for absorption four of the five
surfaces are exposed, but when installed as intended only the front surface
absorbs. So in practice, a two-foot corner wedge like this provides only 65
percent of the absorption claimed. The shorter the wedge, the larger the
disparity between the published and actual absorption.
For some products, like a tube trap, it is not practical to specify an absorption
coefficient because there is no front surface. In that case the correct way to
specify absorption is in sabins, named for acoustics pioneer W.C. Sabine (18681919). The sabin is an absolute measure of absorption, independent of surface
area, and it can be used to compare any two absorbing devices directly and on
equal terms. Top
SIDEBAR: BIG WAVES, SMALL ROOMS
There is a common myth that small rooms cannot reproduce low frequencies
because they are not large enough for the waves to "develop" properly. While it
is true that low frequencies have very long wavelengths - for example, a 30 Hz
wave is nearly 38 feet long - there is no physical reason such long waves cannot
exist within a room that is much smaller than that. What defines the dimensions
of a room are the wall spacing and floor-to-ceiling height. Sound waves
generated within a room either pass through the room boundaries, bounce off
them, or are absorbed. In fact, all three of these often apply. That is, when a
sound wave strikes a wall some of its energy may be reflected, some may be
absorbed, and some may pass through to the outside.
When low frequencies are attenuated in a room, the cause is always canceling
reflections. All that is needed to allow low frequency waves to sound properly and
with a uniform frequency response is to remove or at least reduce the reflections.
A popular argument is that low frequencies need the presence of a room mode
that's low enough to "support" a given frequency. However, modes are not
necessary for a wave to exist. As proof, any low frequency can be produced
outdoors - and of course there are no room modes outdoors! Top
Here's a good way to look at the issue: Imagine you set up a high quality
loudspeaker outdoors, play some low frequency tones, and then measure the
frequency response five feet in front of the speaker. In this case the measured
frequency response outdoors will be exactly as flat as the loudspeaker. Now wall
in a small area, say 10x10x10 feet, using very thin paper, and measure the
response again. The low frequencies are still present in this "room" because the
thin paper is transparent at low frequencies and they pass right through. Now,
make the walls progressively heavier using thick paper, then thin wood, then
thicker wood, then sheet rock, and finally brick or cement. With each increase in
wall density, reflections will cause cancellations within the room at ever-lower
frequencies as the walls become massive enough to reflect the waves.
Therefore, it is reflections that cause acoustic interference, standing waves, and
resonances, and those are what reduce the level of low frequencies that are
produced in a room. When the reflections are reduced by applying bass traps,
the frequency response within the room improves. And if all reflections were able
to be removed, the response would be exactly as flat as if the walls did not exist
at all. Top
SIDEBAR: HARD FLOOR, SOFT CEILING
The following is from an exchange that took place in the rec.audio.pro newsgroup
in May, 2003:
Bill Ruys asked: Why it is recommended to have bare (un-carpeted) floors in the
studio? One web site I visited mentioned that a bare floor was a prerequisite for
the room design with diffusors and absorbers on the ceiling, but didn't say why.
I'm trying to understand the principal, rather than following blindly.
Paul Stamler: Carpet typically absorbs high frequencies and some midrange, but
does nothing for bass and lower midrange. Using carpet as an acoustic
treatment, in most rooms, results in a room that is dull and boomy. Most of the
time you need a thicker absorber such as 4-inch or, better, 6-inch fiberglass, or
acoustic tile, and you can't walk around on either of those. Hence the general
recommendation that you avoid carpet on the floor and use broadband absorbers
elsewhere.
ModeCalc Tutorial
ModeCalc calculates and displays the first 16 axial modes, up to 500 Hz, for any
rectangular room using dimensions you enter as either feet and inches or meters.
It can help you design a new room that sounds as good as possible, or predict
the low frequency behavior of an existing room.
This tutorial explains the basics of room modes, and tells how to use ModeCalc
and interpret its results. Please understand that ModeCalc is not meant to help
you determine low frequency treatment for an existing room. Regardless of what
is predicted (or measured using test equipment) the solution is always the same as much broadband bass trapping as you can manage. Whether your current
room happens to have favorable dimensions or not is irrelevant, unless you're
willing to move the walls! Top
Room Modes
Room modes are natural resonances that occur in every enclosed space, and
the frequency of each resonance is directly related to the room's dimensions. For
example, a room 16 feet long has a mode at 35 Hz because walls that far apart
provide a natural resonance at 35 Hz. Additional modes occur at multiples of 35
Hz because those frequencies also resonate in the same space. Wall spacing
that accommodates one cycle of a 35 Hz wave also fits two cycles of 70 Hz,
three cycles of 105 Hz, and so forth.
When you play a musical note having the same pitch as a natural resonance of
the room, that note will sound louder and have a longer decay time than other
notes. Of course, this is undesirable because some notes are emphasized more
than others, and the longer decay times reduce clarity. Therefore, room modes
are important because they directly affect the character of a room. Although room
resonances can be reduced by adding bass traps, they cannot be eliminated
entirely. Top
For this reason, rooms for recording and playing music are designed to have
many resonances that are distributed evenly, rather than just a few resonances
at the same or nearby frequencies. Playing music in a room with poor mode
distribution is like listening through a 5-band graphic equalizer with one or two
bands turned up all the way. A room with good modes is more like having a 31band equalizer with all the bands turned up. The frequency response still isn't
perfect, but all the small peaks combine to yield an overall response that's
reasonably flat. Therefore, the frequency response of a room with many modes
close together is flatter overall than a room that has fewer modes farther apart.
Small rooms have modes that are spaced farther apart than large rooms
because the first mode in a small room starts at a higher frequency. For example,
when the longest dimension of a room is only 10 feet, the modes for that
dimension start at 56.5 Hz and are 56.5 Hz apart. In larger rooms the first mode
is at a lower frequency so subsequent modes are closer together. Therefore, a
large room has a flatter low frequency response because it has more modes
spaced more closely. Top
The formula used by ModeCalc is extremely simple. For dimensions given in feet
the first mode occurs at 1130 divided by twice the dimension. (1130 is the speed
of sound in feet per second.) All subsequent modes are multiples of that result.
When using meters the formula is 344 divided by twice the dimension. Twice the
dimension is used because a room 10 feet long really has a total distance of 20
feet - the wave travels from one end to the other and back to complete one cycle.
So for a room 10 feet long the first mode occurs at 56.5 Hz:
1130
= 56.5
10 x 2
The second mode for that dimension is two times 56.5 or 113 Hz, the third is
three times 56.5 or 169.5 Hz, and so forth to the tenth mode at 565 Hz. Top
Room Ratios
The worst type of room shape is a perfect cube - say, ten feet long, ten feet wide,
and ten feet high - because all three dimensions are the same and all three
dimensions resonate at the same frequency. A 10 foot cube shaped room will
have a strong inherent resonance near 55 Hz, which is the open A string on a
bass. So when that low A is played it will sound much louder than other notes.
Such a room also has a longer natural decay time at that pitch, so A notes will
sustain longer and conflict with other bass notes that follow.
A room whose dimensions are multiples of each other - for example, 10 feet by
20 feet - is nearly as bad because many of the same frequencies are
emphasized. Therefore, the goal is to have a room shape that spreads the
modes evenly throughout the low frequency range. This is done by designing the
room with dimensions whose ratios of length, width, and height are as unrelated
as possible. And here is where ModeCalc is useful because it tells you at what
frequencies the modes occur and how close together they are. ModeCalc also
shows you the ratios of the dimensions you entered, and lets you compare them
to ratios commonly recommended by acoustic engineers and studio designers.
Top
Using ModeCalc
Instructions at the bottom of the screen explain how to use the program. Simply
enter the Length, Width, and Height using the Tab and Shift-Tab keys to go
between fields, then hit Enter to see the result. Up to 16 modes for each room
dimension are displayed graphically so you can see where they occur and how
they relate to one another. Each set of modes is shown in a different color, and
when two or more modes occur near the same frequency the mode lines are
drawn taller. Note that the graphic display portion of ModeCalc uses logarithmic
spacing. This is how octaves and musical intervals are arranged, and is also how
mode spacing should be viewed.
You can also enter the room dimensions as meters and/or centimeters instead of
feet by using m or M or cm or CM and so forth after the dimension values. Values
can be entered with or without spaces, so '10m' and '10 m' both specify 10
meters. Likewise for feet and inches. Top
Many rooms are not rectangular, and in fact having angled walls or a vaulted
ceiling is desirable. Unfortunately, with angles there is no direct way to determine
the room modes exactly. Modes still exist - they're just more difficult to predict. If
the angles are not too severe you can average the dimensions. For example, if
the ceiling varies from 8 feet to 10 feet high, you can use 9 feet when entering
the height.
When viewing the results look for an even spacing of the modes regardless of
their color (good), and also look for multiple modes that occur at or near the
same frequencies (bad). Also compare the ratios of the dimensions you entered
with the recommended ratios, and compare your room's volume with the
recommended minimum of approximately 2500 cubic feet or 70 cubic meters. Top
To make it easier for you to identify modes that are close together ModeCalc
draws those mode lines taller, which simulates the larger response peak that
occurs. The normal line height is marked with a thin gray horizontal line. When
two modes are adjacent, or at least close, both lines are drawn taller. The closer
the modes are to each other, the taller the lines appear. This also lets you
identify modes that fall on identical frequencies. ModeCalc draws all the lines for
one mode, then the next, and the next. So if several modes are at identical
frequencies one line will hide the other. If you notice that an isolated line is higher
than usual, that means there are at least two modes at that same frequency. You
can then use the Frequency Table display to see them all. Also note that modes
naturally become closer at higher frequencies. Therefore, having taller lines
toward the right side of the graph is normal, and does not mean your room will
really have that rising frequency response.
Finally, if you are using ModeCalc to check an existing room, please don't be
discouraged by poor results. All rooms need bass trapping anyway, and poor
modes can be improved enormously by adding a few more traps. You can also
enter dimensions for a large room having one of the recommended ratios, such
as 23.3 by 16 by 10 feet. Then you'll see how even with the recommended ratios
the modes are still somewhat uneven, and two modes still sometimes occur at
the same frequency. So unless you are willing to move the walls, just accept
what you have, and maybe install a few more bass traps than you had planned
for originally. Then relax and enjoy the music! Top
A Few Words About Mode Types
There are two basic types of room modes - axial and non-axial. Axial modes
occur between two parallel surfaces, where non-axial modes take a more
circuitous route travelling much like a cue ball going around a pool table in a
diamond pattern. The two non-axial mode types are called Tangential (the
reflected waves touch four room surfaces) and Oblique (the waves touch all six
surfaces).
Every rectangular room has three axial modes, with one between the floor and
ceiling, another between the left and right walls, and another between the front
and rear walls. Axial modes are the most important type simply because they are
the strongest. They contribute more to peaks and nulls, and modal ringing
(extended decays), than non-axial modes. This is because the boundaries are
parallel and so the distance between reflections is shorter too. Therefore, axial
modes are the most damaging to accurate music reproduction, and the most
important type to consider. Top
SIDEBAR: CREATING A REFLECTION FREE
ZONE
WHAT:
A useful goal for any room where music plays
through loudspeakers is to create a Reflection
Free Zone (RFZ) at the listening position. The
concept is very simple - to prevent "early
reflections" from obscuring the stereo image. This
occurs when sound from the loudspeakers arrives
at your ears through two different paths - one
direct and the other delayed after reflecting off a
nearby wall.
Just as damaging is when sound from the left
loudspeaker bounces off the right wall and arrives
at the right ear, and vice versa. Similarly, early
reflections off the ceiling and floor can also harm
clarity and imaging. In all cases the reflections
obscures fine detail and make it difficult to localize
the source of the sound or musical instrument.
This drawing, viewed from above, shows the three
main paths by which sound from a loudspeaker
When the budget allows for dedicated construction, early reflections can be
avoided by angling the side walls and sloping the ceiling upward. The studio
below was designed by noted studio designer Wes Lachot, and offers a beautiful
example of such construction. Given a large enough angle the reflections are
directed behind the listening position without having to apply absorbing materials
to the walls or ceiling. This lets you better control the overall ambience in the
room because you don't need additional absorption just to get rid of the
reflections. But most people do not have the luxury of building new walls, so the
only option is to apply absorption at key locations. Top
HOW: The easiest way to tell where to place absorption to avoid early reflections
is with a mirror. This is the thin green object to the right of the listener against the
wall in the drawing. While you sit in the listening position, have a friend place a
mirror flat against the side walls and move it around. Any location in which you
can see either loudspeaker in the mirror should be covered with absorption. It's a
good idea to treat a larger area of the wall than you identify with the mirror, so
you'll be free to move around a little without leaving the Reflection Free Zone.
Once the side wall locations are identified do the same on the ceiling. Although
it's more difficult to slide a mirror around on the ceiling, one way is to attach a
hand mirror to a broomstick with rubber bands. Top
REVISIONS
March 5, 2003: Initial release.
March 16, 2003: The paragraph just above Figure 5 was clarified by Wes Lachot. Thanks Wes!
March 20, 2003: Added Figure 3b and accompanying text showing how to install rigid fiberglass
in an unfinished basement ceiling. Also added a new paragraph under Table 1 explaining the
importance of density in absorbing materials.
March 22, 2003: Added a new last sentence to the second paragraph after Figure 7 offering a
better reason panel bass traps must be sealed air tight.
March 25, 2003: Added the sidebar The Numbers Game to expand on the role of edges when
testing absorbing materials.
March 28, 2003: Changed the formula for calculating the ideal 1/4 wavelength air gap (below
Figure 5) from 1100 to 1130 feet per second, which is more accurate.
April 5, 2003: Added the sidebar Big Waves, Small Rooms to better debunk the myth that low
frequencies require a minimum room size.
April 28, 2003: Added text (just below Figure 3b) describing using large bales of fluffy fiberglass
as a bass trap.
May 14, 2003: Added the sidebar Hard Floor, Soft Ceiling to explain in more depth why that
combination is better than a carpeted floor with a standard drywall ceiling.
June 10, 2003: Added a link to my Graphical Room Mode calculator program in the text below
Table 2.
June 23, 2003: Added three sentences to the end of the paragraph under Figure 6 explaining how
the angle of incidence can affect the absorption of a fiberglass panel. Thanks to Eric Desart for
bringing this to my attention.
June 26, 2003: Added, clarified, and edited throughout to remove what some have perceived as
my bias against foam treatment.
July 12, 2003: Added the online manual for ModeCalc (see June 10 above) as a sidebar, so you
don't have to download and run the program just to read the explanation of modes.
August 28, 2003: Added the sidebar Creating a Reflection Free Zone above.
November 23, 2003: Added two paragraphs about diffusors in the section Diffusors and
Absorbers, directly under the photo of the wood diffusor made by ACID acoustics.
January 14, 2004: Removed the qualification that the front wall angle must be "at least 35
degrees" in the RFZ sidebar because Wes Lachot says the exact minimum angle depends on
several factors. Also made a few other minor edits to clarify the text.
April 21, 2004: Added a few more manufacturers of rigid fiberglass, and explained that FRK
stands for Foil Reinforced Kraft paper.
April 26, 2004: Clarified the difference between a deflector and a true diffusor. Also, clarified the
importance of density in porous absorber materials like rigid fiberglass.
May 4, 2004: Minor edits to the RFZ sidebar to make it clearer that early reflections from either
side wall are a problem, not just the left wall with the right speaker and vice versa.
May 12, 2004: Added text under the Room Symmetry heading explaining the importance of
having loudspeakers fire the long way into the room. It was a slow day so I also added several
other minor enhancements and clarifications.
May 27, 2004: Replaced the graph I had made showing absorption versus air gap with a more
compelling graph from Everest's Master Handbook of Acoustics. Also added test data from
fiberglass manufacturer Johns-Manville showing how increasing the density of rigid fiberglass
enhances its performance at low frequencies.
December 30, 2004: Enhanced ModeCalc to allow entering feet and inches (12'6") rather than
having to use decimal feet (12.5).
February 11, 2005: Added a link to my Density Report in the section about fiberglass density.
Added a new section under Bass Traps Overview to explain modal ringing. Added a paragraph to
enhance the explanation of flutter echo.
February 21, 2005: Numerous minor edits, additions, and clarifications.
August 19, 2005: Added a paragraph to explain that two rigid fiberglass panels 2-inch thick can
be combined to work as well as one panel 4 inches thick. Also added a warning not to have FRK
paper between the layers, or on both the front and rear.
September 21, 2005: Clarified the difference between fiberglass bass traps that act on velocity
versus wood panel traps that absorb via damping wave pressure.
February 3, 2006: Clarified that density is only one factor that affects a material's usefulness as
an absorber, and that at some point the density can be too high.
March 9, 2006: Added text and a graph to the sidebar Creating an RFZ showing how comb
filtering is an equally important problem that is solved by placing absorption at the first reflection
points.
June 18, 2006: Added text near the end of the section Fiberglass Bass Traps explaining how to
treat the cavity above a hung ceiling.
October 12, 2006: Updated the ModeCalc sidebar to link to the new Windows version, and
updated the text to match.
August 10, 2007: Updated Figure 4 with an improved version submitted by Markus Mehlau.
December 2, 2008: Corrected and clarified Figure 4, its caption, and the surrounding text.
Ethan Winer is a reformed rock 'n' roll guitarist who sold his
successful software business in 1992 at the tender age of 43 to
take up the cello. Ethan has, at various times, earned a living as a
studio musician, computer programmer, audio engineer,
composer/arranger, technical writer, and college instructor. He has
had more than 70 feature articles published in computer and audio
magazines including Mix, PC Magazine, EQ, Electronic Musician, Audio Media,
Computer Language, Microsoft Systems Journal, IBM Exchange, Strings,
Keyboard, Programmers Journal, The Strad, Pro Sound News, prorec.com,
Recording, and Sound On Sound. He now heads up RealTraps, manufacturer of
high performance acoustic treatment, and also hosts the EQ Magazine Acoustics
Forum at the MusicPlayer web site.
In addition to technical writing, Ethan has produced two popular Master Class
videos featuring renowned cellist Bernard Greenhouse, as well as five CDs for
Music Minus One including a recording of his own cello concerto. Besides writing
and recording many pop tunes, Ethan has composed three pieces for full
orchestra, all of which have been performed. He lives in New Milford,
Connecticut, with his wife Elli and cat Bear, and plays in both the Danbury
Symphony and the Danbury Community Orchestra where he serves as principal
cellist. You can read more about Ethan's musical exploits on his Music and
Articles pages. Top
Entire contents Copyright 2003-2008 by Ethan Winer and RealTraps, LLC. All rights reserved.