Re 23178

Directional spool valves, direct operated,
with solenoid actuation

RE 23178
Edition: 2013-06
Replaces: 04.09
Type WE
Size 6
Component series 6X
Maximum operating pressure 350 bar [5076 psi]
Maximum flow: 80 l/min [21 US gpm] DC

60 l/min [15.8 US gpm] AC
H7564
Features
Contents
Features1
Ordering code
24
Mating connectors
4
Symbols5
Function, section
6
Technical data
7, 8
Characteristic curves
9
Performance limits
10 12
Dimensions
13 18
Circuit breakers
19
More information
19
4/3, 4/2 or 3/2 directional design

High-power solenoid
Porting pattern according to DIN 24340 form A
Porting pattern according to ISO 4401-03-02-0-05 and
NFPA T3.5.1 R2-2002 D03
Wet-pin DC or AC solenoids with detachable coil
Solenoid coil can be rotated by 90
The coil can be changed without having to open the
pressure-tight chamber
Electrical connection as individual or central connection
Manual override, optional
Spool position monitoring, optional
RE 23178, edition: 2013-06, Bosch Rexroth AG
2/20
WE | Directional spool valve
Ordering code
01
01
02
03
WE
04
05
6X
06
07
08
09
10
11
12
13
14
15
16
3 main ports
4 main ports
4
WE
02
Directional valve
03
Size 6
04
Symbols e.g. C, E, EA, EB, etc; for the possible version, see page 5
05
Component series 60 to 69 (60 to 69: Unchanged installation and connection dimensions)
06
With spring return
6X
no code
Without spring return
Without spring return with detent
OF
07
High-power wet-pin solenoid with detachable coil
08
Direct voltage 24 V
E
G24
W230
AC voltage 230 V 50/60 Hz
W110
W + voltage
AC voltage 120 V or 110 V 50/60 Hz
G205
Direct voltage 205 V
W110R
DC solenoid with rectifier for AC voltage

(not frequency-related; only available with plug-in connection with cover, see page 17)
Connection to AC voltage mains via control with rectifier (see table below and page 4) 1)
For further ordering codes for other voltages and frequencies, see page 8
09
Without manual override
no code
With concealed manual override (standard)
N9 2)
With manual override
N 2)
With lockable manual override "mushroom button" (small)
N4 2)
With lockable manual override "mushroom button" (big)
N5 2; 3)
With manual override "mushroom button" (big), not lockable
N6 2)
With lockable manual override "nut"
N7 2)
Electrical connection
10
Individual connection
Without mating connector, with connector according to DIN EN 175301-803
K4 4)
Without mating connector, with connector AMP Junior-Timer
C4
4)
Without mating connector, with connector DT 04-2PA (Deutsch plug)
K40
Without mating connector, 4-pole with connector M12x1 according to IEC60947-5-2, integrated interference protection circuit and status LED
K72L 5)
Without mating connector, 4-pole with connector M12x1 according to IEC60947-5-2, integrated interference protection circuit and status LED (no connection pin 1 to pin 2)
K73L 5)
4; 7)
Central connection
DL
Cable entry at the cover, with indicator light
DK6L 6)
Central plug-in connection at the cover, with indicator light (without mating connector); connector according
toDIN EN 175201-804
For further electrical connections, see data sheet 08010
AC voltage mains
(admissible voltage tolerance 10%)
Nominal voltage of the DC solenoid in case of

operation with alternating voltage
Ordering code
110 V - 50/60 Hz
96 V
G96
230 V - 50/60 Hz
205 V
G205
Bosch Rexroth AG, RE 23178, edition: 2013-06
Directional spool valve | WE 3/20
Ordering code
01
02
03
WE
04
05
6X
06
07
08
09
10
11
12
13
14
15
16
Spool position monitoring

11
Without position switch
no code
Inductive position switch type QM

Monitored spool position "a"
QMAG24
Monitored spool position "b"
QMBG24
Monitored rest position
QM0G24
Inductive position switch type QR

QR0G24S
Monitored rest position
QRABG24E
Monitored spool position "a" and "b"

Inductive position switch type QL
QLAG24
QLBG24
Inductive proximity sensor type QS

QSAG24W
QSBG24W
QS0G24W
Monitored spool position "0"
QS0AG24W
Monitored spool position "0" and "a"

Monitored spool position "0" and "b"
QS0BG24W
Monitored spool position "a" and "b"
QSABG24W
For more information, see data sheet 24830

12
Without throttle insert
no code
With throttle insert see table:

Port
Throttle in mm [inch]
0.8 [0.031]
1.0 [0.039]
= B08
= B10
1.2 [0.047]
= B12
= H08
= H10
= H12
= R08
= R10
= R12
A and B
= N08
= N10
= N12
= X08
= X10
= X12
Use with flows which exceed the performance limit of the valve (see page 6).
Clamping length
13
no code
42 mm [1.65 inch] (standard)
22 mm [0.87 inch]
Seal material
14
NBR seals
no code
FKM seals
Attention: Observe compatibility of seals with hydraulic fluid used! (Other seals upon request)
15
Without locating hole

With locating hole
With locating hole and locking pin ISO 8752-3x8-St
16
no code
/60 8)
/62
Further details in the plain text
Explanation of the footnotes see page 4.
Preferred types and standard units are contained in

the EPS (standard price list).
4/20
Ordering code
1)
Only for version "individual connection"
7)
2)
The manual override cannot be allocated a safety function. The

manual override units may only be used up to a tank pressure
of50 bar.
8)
3)
With tank pressures above 50 bar, it cannot be guaranteed that

the valve remains in the position switched by the
manualoverrideN5.
4)
Mating connectors, separate order, see below and data

sheet08006
5)
Only version "G24", see data sheet 08010
6)
Mating connector, separate order, material no. R900005538
Only possible in connection with the symbols G, J, D and E as

well a reduced performance limit.
Locking pin ISO 8752-3x8-St, material no. R900005694
(separateorder)
Mating connectors according to DIN EN 175301-803
For details and more mating

connectors, see data
sheet08006
Valve side
Material number
1/2" NPT
(Pg 16)
With
rectifier
12 240 V
With
indicator light and
Zener diode suppression circuit
24 V
Color
Without
circuitry
Gray
R901017010
Black
R901017011
a/b
Black
R901017022
R901017029
R901017025
R901017026
Red/
brown
R900004823
Black
R900011039
a/b
Black
R900057453
R900057455
R900842566
Port
M16 x 1.5
With
indicator light
12 240 V
With
indicator light and
rectifier
12 240 V
Symbols

1)
Example:
Symbol E with spool position "a", ordering code ..EA..
2)
Symbol E1-: P A/B pre-opening,

Caution in conjunction with differential cylinders due to
pressure intensification!
Notices!
Representation according to DIN ISO 1219-1.
Hydraulic interim positions are shown by dashes.

6/20
Function, section
Directional valves of type WE are solenoid operated directional spool valves. They control the start, stop and direction of a flow.
The directional valves basically consist of the housing (1),
one or two electronic solenoids (2), the control spool (3),
and one or two return springs (4).
In the de-energized condition, the control spool (3) is held
in the central position or in the initial position by the
return springs (4) (except for impulse spools). The control
spool (3) is actuated by wet-pin electronic solenoids (2).
To ensure proper functioning, care must be taken that
the pressure chamber of the electronic solenoid is filled
with oil.
The force of the electronic solenoid (2) acts via the
plunger (5) on the control spool (3) and pushes the latter
from its rest position to the required end position. This
enables the necessary direction of flow from P to A and
Bto T or P to B and A to T.
When the electronic solenoid (2) is de-energized, the
return spring (4) pushes the control spool (3) back to its
rest position.
An optional manual override (6) allows the control
spool(3) to be moved without solenoid energization.
Without spring return "O" (only possible with symbols A,

C and D)
This version is a directional valve with 2 spool positions
and 2 electronic solenoids without detent. The valve
without spring return at the control spool (3) has no
defined basic position in the de-energized condition.
Without spring return with "OF" detent (only possible
with symbols A, C and D)
This version is a directional valve with 2 spool positions
and 2 electronic solenoids with detent. The detents are
used to fix the control spool (3) in the relevant spool
position. During operation, continuous application of
current to the electronic solenoid can thus be omitted
which contributes to energy-efficient operation.
Notices!
Pressure peaks in the tank line to two or several valves
can result in unintended control spool movements in
the case of valves with detent! We therefore recommend that separate return lines be provided or a check
valve installed in the tank line.
Due to the design principle, internal leakage is inherent
to the valves, which may increase over the life cycle.

Type 4WE 6 E6X/...E...

Throttle insert
The use of the throttle insert is required when, due to
prevailing operating conditions, flows occur during the
switching processes which exceed the performance limit
of the valve.
Technical data
(for applications outside these parameters, please consult us!)
general
Weight
Valve with one solenoid
kg [lbs] 1.45 [3.2]
Valve with two solenoids
kg [lbs] 1.95 [4.3]
Installation position
Any
Ambient temperature range
C [F] 30 +50 [22 +122] (NBR seals)

20 +50 [4 +122] (FKM seals)
Years 150 (for further details see data sheet 08012)
MTTFd values according to EN ISO 13849

hydraulic
Maximum operating pressure
Ports A, B, P
bar [psi] 350 [5076]
Port T
bar [psi] 210 [3050] (DC); 160 [2320] (AC)

With symbols A and B, port T must be used as leakage oil connection.
Maximum flow
Flow cross-section
(spool position 0)
l/min [US gpm] 80 [21] (DC); 60 [15.8] (AC)

Symbol Q
mm2 Approx. 6% of nominal cross-section
Symbol W
mm2 Approx. 3% of nominal cross-section
Hydraulic fluid
See table below
Hydraulic fluid temperature range
C [F] 30 +80 [22 +176] (NBR seals)

15 +80 [4 +176] (FKM seals)
mm2/s [SUS] 2.8 500 [35 2320]
Viscosity range
Maximum admissible degree of contamination of the hydraulic fluid cleanliness class according to ISO 4406 (c)
Class 20/18/15
1)
Hydraulic fluid
Classification
Suitable sealing materials
Standards
Mineral oils
HL, HLP, HLPD, HVLP, HVLPD
NBR, FKM
DIN 51524
HETG
NBR, FKM
VDMA24568
HEES
FKM
soluble in water
HEPG
FKM
VDMA24568
water-free
HFDU, HFDR
FKM
ISO 12922
containing water
HFC (Fuchs Hydrotherm 46M,

Petrofer Ultra Safe 620)
NBR
ISO 12922
Bio-degradable
Flame-resistant
insoluble in water
Important information on hydraulic fluids!

For more information and data on the use of other hydraulic
fluids, refer to data sheet 90220 or contact us!
There may be limitations regarding the technical valve data (temperature, pressure range, life cycle, maintenance intervals,etc.)!
The flash point of the hydraulic fluid used must be 40 K higher
than the maximum solenoid surface temperature.
1)
The cleanliness classes specified for the components must be

adhered to in hydraulic systems. Effective filtration prevents faults
and at the same time increases the life cycle of the components.
For maintenance requirements of the hydraulic fluid and contamination limit values, see data sheet 07300.
For the selection of the filters, see www.boschrexroth.com/filter.
Flame-resistant containing water:

Maximum pressure difference per control edge 50 bar
Pressure pre-loading at the tank port >20% of the pressure
differential, otherwise increased cavitation
Life cycle as compared to operation with mineral oil HL, HLP
50 to 100%
Bio-degradable: When using bio-degradable hydraulic fluids that
are simultaneously zinc-solving, zinc may accumulate in the fluid
(per pole tube 700mg zinc).
8/20
Technical data
(for applications outside these parameters, please consult us!)
electric
Voltage type
Available voltages 2)
(For ordering codes for AC voltage solenoids, see below)
Direct voltage
Alternating voltage 50/60 Hz
12, 24, 96, 205
110, 230
Voltage tolerance (nominal voltage)
% 10
Power consumption
30
Holding power
VA
50
Switch-on power
VA
220
Duty cycle
% 100
Switching time according ON

to ISO 6403 3)
OFF
Maximum switching frequency
Maximum surface temperature of the coil
Protection class according to DIN EN 60529
ms
25 45
10 20
ms
10 25
15 40
1/h
4)
C [F]
With connector "K4", "K72L", "K73L"
15000
7200
120 [248]
180 [356]
IP 65 (with mating connector mounted and locked)
With connector "C4"
IP 66A (with mating connector mounted and locked)
With connector "K40"
IP 69K (with mating connector mounted and locked)
2)
Special voltages available upon request
3)
The switching times were determined at a hydraulic fluid temperature of 40 C [104 F] and a viscosity of 46cSt. Deviating
hydraulic fluid temperatures can result in different switching
times! Switching times change depending on operating time and
application conditions.
4)
Due to the temperatures occurring at the surfaces of the solenoid

coils, the standards ISO13732-1 and ISO 4413 need to be
adhered to!
The specified surface temperature in AC solenoids is valid for the
faultless operation. In case of error (e.g. blocking of the control
spool), the surface temperature may rise to above 180 C [356 F].
Thus, the system must be checked for possible dangers considering the flash point (see page 7).
As fuse protection, circuit breakers (see table on page 19)
must be used, unless the creation of an ignitable atmosphere can
be excluded in a different way. Thus, the surface temperature can
in case of error be limited to maximally 220 C [428 F].
The tripping current must lie within a time interval of 0.6 s
with8to 10 times the nominal power supply. (tripping characteristics"K").
The necessary non-tripping current of the fuse must not fall
below the value I1 (see table on page 19). The maximum
tripping current of the fuse must not exceed the value I2
(seetable on page 19).
The temperature dependence of the tripping behavior of the
circuit breakers has to be considered according to the manufacturer's specifications.
Notices!
The actuation of the manual override is only possible up to
a tank pressure of approx. 50 bar [725 psi]. Avoid damage to
the bore of the manual override! (Special tool for the
operation, separate order, material no. R900024943).
When the manual override is blocked, actuation of the
opposite solenoid must be ruled out!
The simultaneous actuation of 2 solenoids of one valve
must be ruled out!
Notice!
AC solenoids can be used for 2 or 3 mains; e.g. solenoid
typeW110 for:
110 V, 50 Hz; 110 V, 60 Hz; 120V, 60 Hz
Ordering code
Mains
W110
110 V, 50 Hz
110 V, 60 Hz
120 V, 60 Hz
W230
230 V, 50 Hz
230 V, 60 Hz
When establishing the electrical connection, the protective

earthing conductor (PE ) has to be connected correctly.
Characteristic curves
(measured with HLP46,
oil
= 40 5 C [104 9 F])
Pressure differential in bar [psi]
p-qV characteristic curves

Symbol

Flow in l/min [US gpm]

7 Symbol "R" in spool position B A

Direction of flow
P A
P B
A T
B T
A; B
D; Y
J; Q
8 Symbol "G" and "T" in central position P T

9 Symbol "H" in central position P T
10/20
Performance limits
oil
= 40 5 C [104 9 F])
with only one direction of flow (e.g. from P to A while
port B is blocked).
In such cases of application, please consult us!
The performance limit was determined when the solenoids were at operating temperature, at 10% undervoltage and without tank preloading.
Notice!
The specified performance limits are valid for operation
with two directions of flow (e.g. from P to A and simultaneous return flow from B to T).
Due to the flow forces acting within the valves, the
admissible performance limit may be considerably lower
Operating pressure
inbar [psi]

DC solenoid
Characteristic
curve
Symbol
A; B1)

Solenoid voltage (DC solenoid)

12; 24; 48; 96; 125; 205 V
(other voltages, see page 11)

A; B
F; P
G; H; T
A/O; A/OF; L; U
C; D; Y
10
E; E12); R3); C/O; C/OF; D/O;

D/OF; Q; W
1) With
2) P
manual override
A/B pre-opening
3) Return
flow from actuator to tank
Performance limits
oil
= 40 5 C [104 9 F])
See notice on page 10.
Operating pressure
inbar [psi]



110; 180 V
Operating pressure
inbar [psi]

A; B
F; P
J; L; U
D; C
10
C/O; C/OF; D/O; D/OF;

E; E1; R, Q; W
11
A/O; A/OF
DC solenoid
Symbol

DC solenoid
Characteristic
curve


Characteristic
curve
Symbol
A; B
F; P
J; L; U
A/O; A/OF
10
D; C
11
42; 80; 220 V
12
C/O; C/OF; D/O; D/OF;

E1; R, Q; W
12/20
Performance limits
oil
= 40 5 C [104 9 F])
See notice on page 10.
Operating pressure
inbar [psi]

Characteristic
curve
Symbol
11
A; B1)

AC solenoid 50 Hz

1) With
Solenoid voltage (AC solenoid)

110 V; 50 Hz
120 V; 60 Hz
W230
230 V; 50 Hz
13
A; B
14
F; P
15
G; T
16
17
A/O; A/OF; C/O; C/OF; D/O; D/OF;

E; E12); J; L; M; Q; R3); U; W
18
C; D; Y

W110
12
2) P
manual override
A/B pre-opening
3) Return
(other voltages upon request)
Operating pressure
inbar [psi]

AC solenoid 60 Hz

Characteristic
curve
Symbol
19
A; B1)

Solenoid voltage (AC solenoid)

110 V; 60 Hz
W230
230 V; 60 Hz
(other voltages upon request)

W110

1) With
2) P
20
21
A; B
22
F; P
23
G; T
24
J; L; U
25
A/O; A/OF; Q; W
26
C; D; Y
27
28
C/O; C/OF; D/O; D/OF; E; E12); M; R3)
manual override
A/B pre-opening
3) Return

Dimensions: Valve with DC solenoid Individual connection

(dimensions in mm [inch])

Dimensions for manual overrides see page 15.

Item explanations, valve mounting screws and subplates
see page 18.
0,01/100
[0.0004/4.0]
Rzmax 4
Required surface quality of
the valve contact surface
14/20
Dimensions: Valve with DC solenoid Central connection


0,01/100
[0.0004/4.0]
Rzmax 4

Terminal assignment with central connection:

1 solenoid:
Always connect the solenoid to terminals 1 and 2,
the protective earthing connector to terminal
PE
2 solenoids:
Always connect solenoid "a" to terminals 1 and 2,
solenoid "b" to terminals 3 and 4,
the protective earthing conductor to terminal
PE
Dimensions for manual overrides see page 15.

see page 18.
Dimensions: Valve with DC solenoid Manual overrides



see page 18.

0,01/100
[0.0004/4.0]
Rzmax 4
16/20

0,01/100
[0.0004/4.0]
Rzmax 4

see page 18.

Dimensions: Valve with AC solenoid Individual connection

Dimensions: Valve with AC solenoid Central connection


0,01/100
[0.0004/4.0]
Rzmax 4

Terminal assignment with central connection:

1 solenoid:
Always connect the solenoid to terminals 1 and 2,
the protective earthing connector to terminal
PE
2 solenoids:
Always connect solenoid "a" to terminals 1 and 2,
solenoid "b" to terminals 3 and 4,
the protective earthing to terminal
PE

see page 18.
18/20
Dimensions
1.1 Solenoid "a"
1.2 Solenoid "b"
2 Dimension for solenoid with concealed manual override "N9"
(standard)
3 Dimension for solenoid with manual override "N"
4 Dimension for solenoid without manual override
5 Dimension for solenoid with manual override "N7"
6 Dimension for solenoid with manual override "N5" and "N6"
6.1 Manual override "N5"
6.2 Manual override "N6"
7.1 Mating connector without circuitry for connector "K4"
(separate order, see page 4 and data sheet08006)
7.2 Mating connector (AMP Junior Timer) with connector "C4"
(separate order, see data sheet 08006)
7.3 Mating connector DT 04-2PA (Deutsch plug) with connector "K40"
(separate order, see data sheet 08006)
7.4 Mating connector angled with M12x1 plug-in connection
with status LED "K72L" (separate order, see data
sheet08006)
8 Mating connector with circuitry for connector "K4"
(separate order, see page 4 and data sheet 08006)
9 Cable gland Pg 16 [1/2" NPT] "DL"
Subplates according to data sheet 45052

(separate order)
(without locating hole)
G 341/01 (G1/4)

G 342/01 (G3/8)

G 502/01 (G1/2)
(with locating hole)
G 341/60 (G1/4)

G 342/60 (G3/8)

G 502/60 (G1/2)

G 341/12 (SAE-6) 1)

G 342/12 (SAE-8) 1)

G 502/12 (SAE-10) 1)
1) Upon request
Valve mounting screws (separate order)
Clamping length 42 mm:
4 metric hexagon socket head cap screws
ISO 4762 - M5 x 50 - 10.9-flZn-240h-L
(friction coefficient total = 0.09 to 0.14);
tightening torque MA = 7 Nm [5.2 ft-lbs] 10%,
material no. R913000064

or
4 hexagon socket head cap screws
ISO 4762 - M5 x 50 - 10.9 2)
tightening torque MA = 8.1 Nm [6 ft-lbs] 10%
10 Central plug-in connection "DKL"
4 hexagon socket head cap screws UNC 10-24 UNC x 2" ASTM-A574
(friction coefficient total = 0.19 bis 0.24);
10.1 Angled socket (red, separate order)

Material no. R900005538)
11 Name plate
12 Identical seal rings for ports A, B, P, T
Notice! The ports are clearly determined according to
their tasks and must not be arbitrarily interchanged
orclosed.
13 Plug screw for valves with one solenoid
14 Space required to remove the mating connector/
angledsocket
15 Space required to remove the coil
16 Mounting nut, tightening torque MA = 4+1Nm [2.95+ 0.74ft-lbs]
17 Porting pattern according to DIN 24340 form A (without
locating hole), or ISO 4401-03-02-0-05 and
NFPA T3.5.1 R2-2002 D03 (with locating hole for locking pin
ISO 8752-3x8-St, material no. R900005694, separate order)
Clamping length 22 mm:

4 metric hexagon socket head cap screws
ISO 4762 - M5 x 30 - 10.9-flZn-240h-L

or
4 hexagon socket head cap screws
ISO 4762 - M5 x 30 - 10.9 2)
tightening torque MA = 8.1 Nm [6 ft-lbs] 10%
4 hexagon socket head cap screws UNC 10-24 UNC x 1 1/4"
18 Alternative clamping length (): 22 mm [0.87 inch]

19 Cover
Attention!
The valve may only be operated with properly mountedcover.
2)
Not included in the Rexroth delivery range
Circuit breakers with tripping characteristic "K"

according to EN60898-1 (VDE 0641-11), EN60947-2 (VDE 0660-101), IEC60898 and IEC60947-2
Lower rated current

I1 in A
Upper rated current

I2 in A
AC solenoid
Lower rated current

I1 in A
Upper rated current

I2 in A
W24
2.30
3.60
W42
1.45
1.92
W24
1.73
2.40
W42
1.13
W48
1.15
1.92
1.92
W48
1.09
W100
1.92
0.64
0.90
W100
0.58
0.90
W110
0.60
0.90
W110
0.52
0.90
W115
0.52
0.90
W115
0.43
0.90
W127
0.48
0.60
W127
0.37
0.60
W200
0.33
0.60
W200
0.30
0.60
W220
0.31
0.60
W220
0.26
0.36
W230
0.26
0.36
W230
0.20
0.36
W240
0.26
0.36
W240
0.22
0.36
AC solenoid
50 Hz
50 Hz
More information
Subplates
Data sheet 45052
Inductive position switch and proximity sensors (contactless)
Data sheet 24830
Smoothly switching version
Data sheet 23183
Mineral oil-based hydraulic fluids
Data sheet 90220
Reliability characteristics according to EN ISO 13849
Data sheet 08012
General product information on hydraulic products
Data sheet 07008
Installation, commissioning and maintenance of industrial valves
Data sheet 07300
Hydraulic valves for industrial applications
Data sheet 07600-B
Selection of the filters
www.boschrexroth.com/filter
20/20
Notes
Bosch Rexroth AG
Hydraulics
Zum Eisengieer 1
97816 Lohr am Main, Germany
Phone +49 (0) 93 52/18-0
documentation@boschrexroth.de
www.boschrexroth.de
This document, as well as the data, specifications and other information set
forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
reproduced or given to third parties without its consent.
The data specified above only serve to describe the product. No statements
concerning a certain condition or suitability for a certain application can be
derived from our information. The information given does not release the user
from the obligation of own judgment and verification. It must be remembered
that our products are subject to a natural process of wear and aging.

Re 23178

Uploaded by

Copyright:

Available Formats

Re 23178

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Re 23178

Uploaded by

Copyright:

Available Formats

Directional spool valves, direct operated,

with solenoid actuation

4/3, 4/2 or 3/2 directional design

RE 23178, edition: 2013-06, Bosch Rexroth AG

WE | Directional spool valve

Component series 60 to 69 (60 to 69: Unchanged installation and connection dimensions)

With spring return

Without spring return

Without spring return with detent

High-power wet-pin solenoid with detachable coil

AC voltage 230 V 50/60 Hz

AC voltage 120 V or 110 V 50/60 Hz

Direct voltage 205 V

DC solenoid with rectifier for AC voltage

Without manual override

With concealed manual override (standard)

With manual override

With lockable manual override "mushroom button" (small)

With lockable manual override "mushroom button" (big)

With manual override "mushroom button" (big), not lockable

With lockable manual override "nut"

Without mating connector, with connector AMP Junior-Timer

Without mating connector, with connector DT 04-2PA (Deutsch plug)

Cable entry at the cover, with indicator light

Nominal voltage of the DC solenoid in case of

Bosch Rexroth AG, RE 23178, edition: 2013-06

Directional spool valve | WE 3/20

Spool position monitoring

Without position switch

Inductive position switch type QM

Monitored spool position "b"

Monitored rest position

Inductive position switch type QR

Monitored rest position

Monitored spool position "a" and "b"

Monitored spool position "b"

Inductive proximity sensor type QS

Monitored spool position "b"

Monitored spool position "0"

Monitored spool position "0" and "a"

Monitored spool position "a" and "b"

For more information, see data sheet 24830

Without throttle insert

With throttle insert see table:

42 mm [1.65 inch] (standard)

Without locating hole

Further details in the plain text

Explanation of the footnotes see page 4.

Preferred types and standard units are contained in

RE 23178, edition: 2013-06, Bosch Rexroth AG

WE | Directional spool valve

Only for version "individual connection"

The manual override cannot be allocated a safety function. The

With tank pressures above 50 bar, it cannot be guaranteed that

Mating connectors, separate order, see below and data

Only version "G24", see data sheet 08010

Mating connector, separate order, material no. R900005538

Only possible in connection with the symbols G, J, D and E as

Mating connectors according to DIN EN 175301-803

For details and more mating

Directional spool valve | WE 3/20

Directional spool valve | WE 5/20

Directional spool valve | WE 7/20

Directional spool valve | WE 9/20

Directional spool valve | WE 11/20