VW MKIII VR6 Coil Pack Fix DIY PDF

THE POCKET ROCKET - For Volkswagen Enthusiasts
menu :
: MAIN
: FEATURES
: EVENTS
: QUARTER MILE RACING
Page 1 of 4
: VW TECH
: FORUMS AND CLASSIFIEDS
: LINKS
: CONTACT
for advertising info click here
Thursday, May 17, 2007
PART I - BACKGROUND.
PART II - DIAGNOSIS.
What is a coil pack?
If you have noticed that on cool,

damp days or after driving in the
rain (especially on the highway,
especially behind cars/trucks) the
engine is running rough and
misfiring, chances are the coil pack
has a crack(s).
Thanks for asking. The coil pack

replaces distributor caps on "new and
improved" ignition system. Instead of
having a rotor and distributor cap
"distribute" the ignition spark to
individual cylinders at the right time
and order, the spark is controlled
electronically though the electronic
ignition system. The coil pack is
where the actual electrical current
(spark) is sent to each spark plug via
the wires.
When this happens, the "check

engine light" WILL come on
immediately, because the emissions
just went to hell.
If possible, pull over and pop the
hood ASAP. If it is a cracked coil
pack you will notice (at least I did
each time there was a problem):
(A) a fairly loud "snapping" or
"clicking" sound immediately
followed by a rough spot in the idle.
The pack is generally comprised of a
http://www.pocketrocket.ca/vr6_coilpack.html
(B) visible sparks running along the

coil pack, generally from the wire
terminal (where the spark plug
wires attach) towards the metal
part of the coil pack. Each spark is
tracing a water filled crack and
grounding the spark to the engine
block rather than travelling along
5/17/2007
metal base with a plastic top

(insulates the metallic parts so the
current is not immediately
grounded).
The coil pack is located on the right
side of the engine (look from the
front) under the plastic manifold
covers. Just follow the pretty spark
plug wires to the end and they attach
to the coil pack.
It seems that the VR6 coil packs (at
least pre 98's) just suck. I am not
sure if the plastic is not formulated
properly, if the molding is not
performed properly or if the design
does not distribute stress/heat well
but by listening to the problems
people on this list have had, the coil
pack is NOT a quality part. Either
that or it is designed obsolescence,
keeping the dealer stocked with
easy, $500 repairs every 30,000
miles.
PART III - REPAIR OPTIONS.
(1) Take car to dealer, tell them the

coil pack is bad. They will respond
"that's nice but we will have to
confirm" ($56.49). They will then call
back several hours later saying "you
have a bad coil pack" (duh) and that
for just $350 in parts and $100 in
labour we can put on a new one. So
pony up $500.
(2) Lucky for you, there are
engineers out here who just can't
stand it when a biased party tells me
that an inferior part needs to be
replaced with the same inferior part.
So like all good men, especially
engineers, I start to tinker. Leading
to a "fix" that has worked for 11,000
miles so far - The $3.49 Epoxy
Solution.
Page 2 of 4
the spark plug wire. Try to

remember or draw the location of
the sparks.
(C) If you cannot pull over, or if
you want to check later after the
weather gets a bit nicer you can
easily simulate rain. Get a plant
spray bottle/mister and fill with
clean water. Start up the engine
and give the coil pack area a good
misting with the bottle. It may take
a few sprays to get the pack nice
and wet. This should start the light
show again. Try to remember
where the crack(s) is or make a
sketch.
You now know you have the
dreaded cracked coil pack. But have
no fear, there are options...
PART IV - THE $3.49 EPOXY

SOLUTION.
Drive a different car to Home

Depot, Lowe's, etc. and get a
package of high strength, high
temperature epoxy. I *think* the
brand I used was "Poxy-Weld"? It is
the classic twin tube syringe, silver
in color with a cardboard packaging
display that unfolded to give
product information. It is made to
repair metal, plastic, etc. with
higher operating temperatures. It
has Kevlar flakes to add strength. I
think the one I used was rated to
250 or 350 degrees. It was like
$3.49 for the tube.
In order to make the repair you will
need:
*torx wrenches or driver
*allen (hex) wrenches or driver
*damp rag
*hair dryer
*epoxy
*12 hours (1 hour working, 11
hours waiting)
STEP 1.
STEP 2.
Coil pack removal. This is very easy.

First remove the plastic manifold
covers. This requires torx head
wrenches/driver. IMPORTANT.
Before trying to loosen the screws,
bang the top of the wrench/driver
with a hammer while the
wrench/driver is on the screw.
Unplug the wire harness attached

to the top of the coil pack and move
it out of the way. If I remember
right it has pinch clips on the side
to unlock the harness. Unplug the
spark plug wires. Make a diagram
of which plug number goes where.
5/17/2007
Page 3 of 4
Aluminium tends to "corrode" quickly

(look at the manifold) and slightly
bond to itself. By hitting with a
hammer, the bond is broken and the
screws can be easily removed. I
know this from experience (i.e.
partially stripped screw heads). If
you strip the screw heads, I used a
slightly larger allen wrench and
literally hammered it into the torx
grooves. Of course you then need
new screws ($12). Once the four
screws are out, plastic covers come
off easily. You can now see the whole
coil pack.
STEP 3.
STEP 4.
The coil pack is held to the engine

block by four, long allen (hex)
screws. I found a hex driver with an
articulated joint made the removal
easier. A socket wrench should also
work. Unscrew and remove the pack.
It is a bit heavier than you might
think so be careful when removing
the last two screws.
Take coil pack inside. Ignore the

"you are not a mechanic" insults
coming from the living room (be
the ball Danny). Take off plastic
cover on the top of the pack (just
pop over the small clips). Wash off
the coil pack with a damp cloth. If it
is really dirty, a bit of Dawn can
work wonders. Just make sure to
wipe off the soap well. You will now
want to dry the pack WELL with the
hair dryer. I was probably a bit anal
about it but I sat in front of the TV
for like 20 minutes just drying the
pack. Since there is no real way to
tell if all the water is out of the
cracks, I was conservative.
STEP 5.
STEP 6.
You are now ready for the epoxy. Mix

a healthy amount is a small
disposable container. I used a
popsicle stick to mix and spread.
Start applying a liberal coat of epoxy.
The first time I did it, I only covered
the places I had seen sparks. Of
course about two weeks after the
first fix, a new crack or one I had not
seen developed so I did it again. This
time I covered the entire plastic
portion of the coil pack. Concentrate
on the area between each terminal
and the edge of the pack. No
problem since. So either coat the
cracked areas or just do the whole
thing. I would recommend the whole
thing. The epoxy tends to get a bit
sticky so it may work best doing two
batching.
Set coil pack in a warm place to dry

overnight. I did this in December so
by a radiator worked well. Just
don't put outside since it makes the
curing take a lot longer.
Reinstall the next morning. I
actually did this before work one
day and it took all of about 10
minutes. Put plastic cover back on
pack. Install pack with four hex
bolts and reattach the wire harness.
Plug in spark plug wires in SAME
LOCATIONS. Install plastic
manifold covers (I put some grease
on the aluminium screws before
installing to prevent locking).
STEP 7.
Start car and she should be running

like new. It will take at least 3 warm-
5/17/2007
up/cool-down cycles to reset the

"check engine light" I hope this helps
those interested. It has worked like a
dream for me. And at 3.49 vs.
500.00 it is a no brainer to at least
try it. Worst case you know how to
install the pack and can just order
the part from a mail order place
(Adirondack, potter, etc.) saving the
dealer rape. I would actually
recommend doing this as
preventative maintenance. It's
cheap, easy and can same some
significant bucks. If I ever HAVE to
get a new pack I will do it before
installing, just to reinforce it against
cracks.
Page 4 of 4
VW TECH BY: Marc Gallagher
This site is not affiliated with Volkswagen of America, Audi of America

or its parent company VW AG or Audi AG.
For more info or questions email: info@pocketrocket.ca
5/17/2007

VW MKIII VR6 Coil Pack Fix DIY PDF

Uploaded by

Copyright:

Available Formats

VW MKIII VR6 Coil Pack Fix DIY PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

VW MKIII VR6 Coil Pack Fix DIY PDF

Uploaded by

Copyright:

Available Formats

THE POCKET ROCKET - For Volkswagen Enthusiasts

: QUARTER MILE RACING

: FORUMS AND CLASSIFIEDS

for advertising info click here

Thursday, May 17, 2007

What is a coil pack?

If you have noticed that on cool,

Thanks for asking. The coil pack

When this happens, the "check

The pack is generally comprised of a

(B) visible sparks running along the

THE POCKET ROCKET - For Volkswagen Enthusiasts

metal base with a plastic top

PART III - REPAIR OPTIONS.

(1) Take car to dealer, tell them the

the spark plug wire. Try to

PART IV - THE $3.49 EPOXY

Drive a different car to Home

Coil pack removal. This is very easy.

Unplug the wire harness attached

THE POCKET ROCKET - For Volkswagen Enthusiasts

Aluminium tends to "corrode" quickly

The coil pack is held to the engine

Take coil pack inside. Ignore the

You are now ready for the epoxy. Mix

Set coil pack in a warm place to dry

Start car and she should be running

THE POCKET ROCKET - For Volkswagen Enthusiasts

up/cool-down cycles to reset the

VW TECH BY: Marc Gallagher

This site is not affiliated with Volkswagen of America, Audi of America

You might also like