Bsa 1850120 12CF

Vertically Polarized, Panel 120 / 16 dBi
BSA-1850120/12CF __
Mechanical specifications
Length
4)
1800 mm
70.9 in
Width
70 mm
2.8 in
Depth
Depth with t-bracket
50 mm
78 mm
2.0 in
3.1 in
Weight
2.9 kg
6.5 lbs
Wind Area
Fore/Aft
Side
When ordering replace ___ with connector type.
Radiation pattern1)
-110
-100
-90
-80
-70
-120
-60
-130
-50
-140
-40
-30
-150
0.13 m2
1.36 ft2
0.09 m2
0.97 ft2
Rated Wind Velocity (Safety factor 2.0)

>512 km/hr >312 mph
-160
-20
-170
-10
35 30 25 20 15 10 5
180
170
10
160
Wind Load @ 100 mph (161 km/hr)

Fore/Aft
240 N
54 lbs
Side
133 N
20
30
150
140
40
130
30 lbs
50
120
60
110
Antenna consisting of aluminum alloy with brass

feedlines covered by a UV safe fiberglass radome.
100
90
80
70
Horizontal
Mounting and Downtilting
-110
-100
-90
-80
-70
-120
Mounting brackets attach to a pipe diameter of

50-102 mm (2.0-4.0 in).
-60
-130
-50
-140
-40
-30
-150
Mounting bracket kit #26799997

Downtilt bracket kit #26799999
The downtilt bracket kit includes the mounting
bracket kit.
Electrical specifications
Frequency Range
1850-2000 MHz
Impedance
50
Connector(s)
NE or E-DIN
1 port / center
VSWR
1.4:1
Polarization
Vertical
Gain
16 dBi
Power Rating
250 W
-160
-20
-170
-10
35 30 25 20 15 10 5
180
1)
1)
2)
1)
1)
1)
Half Power Angle

H-Plane
120
E-Plane
Electrical Downtilt
Null Fill
10%
Lightning Protection
Direct Ground
Amphenol Antels
Exclusive 3T (True
Transmission Line
Technology)
Antenna Design:
10
160
20
30
150
140
40
130
3)
170
50
120
60
110
100
90
80
70
z Watercut brass feedline assembly for

consistent performance.
Vertical
z Unique feedline design eliminates the need

for conventional solder joints in the signal
path.
Radiation patterns for all antennas are

measured with the antenna mounted on
a fiberglass pole.
z A non-collinear system with access to

every radiating element for broad bandwidth and superior performance.
z Air as insulation for virtually no internal
signal loss.
Mounting on a metal pole will typically

improve the Front-to-Back ratio.
This Amphenol Antel antenna is under a fiveyear limited warranty for repair or replacement.
Antenna available with center-fed connector
only.
1) Typical values.
2) Power rating limited by connector only.
3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.
4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.
CF Denotes a Center-Fed
Connector.
1850-2000 MHz
Amphenol Antel, Inc.

1300 Capital Drive
Rockford, Illinois 61109 USA
Toll-Free (888) 417-9562
Fax. (815) 399-0156
antel@antelinc.com
Tel. (815) 399-0001

www.antelinc.com
Revision iDEN: 7/10/07

Bsa 1850120 12CF

Uploaded by

Copyright:

Available Formats

Bsa 1850120 12CF

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bsa 1850120 12CF

Uploaded by

Copyright:

Available Formats

Vertically Polarized, Panel 120 / 16 dBi

When ordering replace ___ with connector type.

Rated Wind Velocity (Safety factor 2.0)

Wind Load @ 100 mph (161 km/hr)

Antenna consisting of aluminum alloy with brass

Mounting and Downtilting

Mounting brackets attach to a pipe diameter of

Mounting bracket kit #26799997

Half Power Angle

z Watercut brass feedline assembly for

z Unique feedline design eliminates the need

Radiation patterns for all antennas are

z A non-collinear system with access to

Mounting on a metal pole will typically

Amphenol Antel, Inc.

Tel. (815) 399-0001

Revision iDEN: 7/10/07

You might also like