Idea Gold

Function

High performance water and oil repellent with natural look.

Use for

Marble, Granite, Terrazzo, Marble Resin, Concrete, Calcareous Stones

Features
High performance water and oil repellent studied for protection of stone against penetration of water,
oils, grease, humidity, and stops salt resurfacing. The products does not change the color of the stone,
does not give wet or shiny look. It does not form any film and lets the stone breathe. It has outstanding
resistance to freezing and defrost cycles, bad weather and UV rays.

Suggestions
It is possible to apply more layers of product after two hours from the previous application to improve
the protection. It is suggested to apply the product till the complete saturation of stone. In case of
small pieces treat them by immersion. The support has to dry for 24 hours. In case of treatment of
statues or decorations pay attention to reach well cavities and corners.
Read carefully recommendations printed on the tin before use.

Application
Surface must be clean and dry.
USE: brush, roller, cloth or fleece.
If possible, apply the product by brush because it allows the product to
penetrate well into the stone.
Dilution : Don't dilute, it is ready to use.

SEALERS

Coverage
For protection polished marble and granite with 1 liter of product it is possible to treat
15-30 sqm. In case of unpolished marble, calcareous stone, limestone, sand stone
and concrete with 1 liter of product it is possible to treat 8-15 sqm.

Idea HP/XC
Function

Water and oil repellent with natural look / wet look.

Use for

Marble, Granite, Terrazzo, Marble Resin, Calcareous Stones

Features
Clear impregnating agent for protection of stones against penetration of water, oils, grease and
humidity. Optimal performance on polished material. It penetrates deeply into the stone, does not
change the original color of the stone. It does not form a film and lets the surface breath. It has good
resistance to UV rays. It prevents formation of mildew and stops salt efflorescences.

Suggestions
It is possible to apply more layers of product two hours from the previous application to improve the
protection. It is suggested to apply the product till the complete saturation of stone. In case of small
pieces treat them by immersion. The support has to dry for 24 hours. In case of treatment of statues
or decorations pay attention to reach well cavities and corners.
Read carefully recommendations printed on the tin before use.

Coverage
For protection of polished marble and granite with 1 liter of product it is possible to treat 15-30
sqm. In case of unpolished marble, granite, calcareous stone, limestone, sand stone and
concrete with 1 liter of product it is possible to treat 8-15 sqm.

Application
Surface must be clean and dry.
USE: brush, roller, cloth or fleece.
If possible, apply the product by brush because it allows the
product to penetrate well into the stone.
Dilution : Don't dilute, it is ready to use.

Idea Dark
Function

Stone impregnating enhancer with extra darkening action.

Use for

Marble, Granite, Terrazzo, Marble Resin, Concrete, Calcareous Stones

Features
Specific for absorbent dark and black stones, it intensifiles the natural color of the surface, can mask scratches, defects
and imperfections of the stone. Water-resistant, it contains siloxane reagents, ideal for protective treatment. Good
penetration, it does not form a film and lets the surface breath. It does not turn to yellow, perfect for indoor or outdoor
surfaces. It has good resistance to UV rays. It prevents formation of mildew and does not allow the efflorescence. It is
excellent to give color to marble-resin, and other agglomerates

Suggestions
It is possible to apply more layers of product two hours from the previous application to enhance further the color and to
improve the protection. It is suggested to apply the product till the complete saturation of stone. For small pieces treat
them by immersion. The support has to dry for 24 hours. In case of treatment of statues or decorations pay attention to
reach well cavities and corners.
Read carefully recommendations printed on the tin before use.
Application

Coverage

Surface must be clean and dry. USE: brush, roller, cloth or fleece.
If possible, apply the product by brush because it allows the product to
penetrate well into the stone. Remove the excess of products with a dry
cloth or paper towel, after 10-15 minutes. Let the product dry naturally.

Idea Black

SEALERS

For protection polished marble and granite with 1 liter of product it is possible to treat 15-30 sqm.
In case of unpolished marble, granite, calcareous stone, limestone, sand stone and concrete with 1
liter of product it is possible to treat 8-15 sqm.

Function

Black dyed water and oil repellent.

Use for

Marble, Granite, Concrete, Agglomerates

Features
Black dyed, silicon based water and oil repellent and protective product, suitable as coloring agent for black
materials. It penetrates easily without forming any superficial film and lasts longtime, even if applied outisde. IDEA
BLACK is stable to UV rays, it is anti-adhesive and antistatic, so the treated material remains clean.

Suggestions
Application
The longer IDEA BLACK remains on the material to dry, the darker will be the obtained color.
Do not wash the treated surfaces with alcohol or strong alkali based products.
Surface to be treated must be clean and dry.
Read carefully recommendations printed on the tin before use.
USE: brush, roller, cloth, fleece or in-line.
Distribute evenly the eproduct and wait for drying. Remove excess with a clean cloth,
Coverage
with a single disc machine equipped with a white disc, or with a in-line polishing
machine. The longer IDEA BLACK remains on the material to dry, the darker will be the
With a liter of product it is possible to treat 15-60 sqm (160-645 sq. ft.) depending of
obtained color.
nature and finishing of material.

Strong 2000
Function

Clear siloxane consolidating and anti salt resurfacing water-proof product.

Use for

Marble, Granite, Terrazzo, Marble Resin & Calcareous Stones

Features
The product protects buildings and stones against penetration of water, acid rains and humidity. It has also a
consolidating action on friable and corroded stones, it avoids calcarization and stone transformation into a
crumbling mass. It does not the change the original color, also after UV rays exposition it does not give a wet
look or shine to the treated surface. It prevents formation of mildew. It stops salt resurfacing.

Suggestions
It is suggested to apply the product till the complete saturation of the stone, without interruption. For small
pieces treat it by immersion. The support has to dry for 24 hours. In case of treatment of statues or
decorations pay attention to reach well cavities and corners.
Read carefully recommendations printed on the tin before use.

SEALERS

Coverage
With 1 liter of product it is possible to treat 8-15 sqm, depending on the nature of the
substrate.

Application
Surface must be clean and dry.
USE: brush, roller, cloth or fleece.
If possible, apply the product by brush because it allows the
product to penetrate well into the stone.
Dilution : Don't dilute, it is ready to use.

Limesealer
Function

Water and oil repellent bonding and anti salt resurfacing.

Use for

Limestone, Sandstone & Calcareous Stones

Features
Transparent water and oil sealer that strengthens the stone. It prevents salts and efflorescence form surfacing.
It gave an optimum protection to the treated stone against humidity, acid rain. It prevents formation of mildew,
but at the some lets the stone breath. It does not change the color to the polished stone. It contains siloxane
and fluorinate resins specifically studied for weak stones.

Suggestions
Apply wet on wet, without allowing the pervious layer to dry.
In case of small pieces treat them by immersion.
In case of treatment of statues or decorations pay attention to reach well cavities and corners.
The support has to dry for 24 hours.
Read carefully recommendations printed on the tin before use.

Coverage
With 1 liter of product it is possible to treat 8-20 sqm

Application
Surface must be clean and dry.
USE: brush, roller, cloth or fleece.
If possible, apply the product by brush because it allows the
product to penetrate well into the stone. Continuously repeat
the application, without interruption, until the stone has been saturated.
Dilution : Don't dilute, it is ready to use.

Idea Rapid Color

Function

Antistain deep enhancer.

Use for

Limestone, Sandstone, Concrete & Very Absorbent Stones.

Features
Clear impregnating solvent based agent for protection of buildings and stones against penetration of
water, oils, grease and humidity. Optimal performances on polished material, does not allow the
efflorescence to exit from the stone, it penetrates deeply into the stone, it enhance the original color of
the stone keeping a deep wet look providing a very good protection. Tests carried out in laboratories
demonstrate resistance to UV rays. It prevents formation of mildew.

Suggestions
We recommend applying the product until complete saturation of the stone. Taking care to apply it wet
on wet, ie without leaving the first coat to dry, but continuing the application. Do not dilute the product Application
with water or other solvents because the preparation is ready for use. The material to be treated mustSurface must be clean and dry.
be completely dry. In the case of treatments for statues, vases or decorative items, pay close attentionUSE: brush, roller, cloth or fleece.
to cavities. Read carefully recommendations printed on the tin before use.
If possible, apply the product by brush, making pressure, will facilitate

Coverage

AQ Proof

SEALERS

For the protection of limestone, one liter of product can treat 8-12 sqm (80-140 sq.ft.),
depending on the absorption and degree of finish of the material.

penetration into frames and cavities. Continuously repeat the application,

without interruption, until the stone has been saturated (the stone does not
absorb further product). Dilution : Don't dilute, it is ready to use.

Function

Water-based water & oil repellent with natural effect.

Use for

Limestone, sandstone, terracotta, concrete, unpolished stones and agglomerates.

Features
Natural effect water based water and oil sealer, ready to use, suitable for protection treatment of limestone,
sandstone, terracotta, cement, not polished stones and agglomerate. AQ PROOF protects against watery or
oily/greasy dirt, reduces the tendency of material to become dirty and in most of cases, does not changes the
original color of treated stone. AQ PROOF penetrates deeply, does not form any film on surface of stone and let
it breathe. It does not turn to yellow and it is suitable for both indoor and outdoor treatments; test carried out in
laboratory show that AQ PROOF resists against UV ray. It also prevents formation of mildew.

Suggestions
It is suggested to apply product until complete saturation of stone. It is suggested to apply the product on
dry material; anyway, treatment can be carried out even if material has some residual moisture.
Once treated, material must be let to dry for 48 hours until complete polymerization occurs.
In case of treatment of statues, decorations etc. pay attention to protect well cavities and corners.
Read carefully recommendations printed on the tin before use.

Coverage
With one liter of product, it is possible to treat 7-20 sqm (75-215 sq. ft.) of unpolished
material.

Application
Surface must be clean and dry.
USE: brush, roller, cloth or fleece.
Apply AQ PROOF with brush making pressure, this will facilitate penetration
into frames and cavities. Apply a second coat after one hour, and then
remove the excess of product within 15 minutes. It is possible to apply more
coats of product, in order to improve the protection; pay attention to remove
possible excess od product at the end of treatment.
Dilution : Don't dilute, it is ready to use.

Mastice 2000
Function

High quality polyester mastic.

Use for

Marble, Agglomerates, Marble Resin, Terrazzo, Calcareous Stones

Features
It has an excellent adhesive power, thanks to its fluidity penetrates easily into porosities and
cavities of the stones. After drying it can be processed like a stone. It resists very well to most of
the chemical product as oils, grease, cleaners and solvents. Available In liquid and solid version
and in following color: transparent, white, light straw yellow, dark straw yellow, svilari, ocher
yellow, carnic grey, assisi red, verona red, light green, black.

Suggestions

MASTICS

It is possible to use an higher or lower % of catalyzer to quicken or slow down the catalysis. It is
possible to color the mastic with appropriate coloring tubes.
Read carefully recommendations printed on the tin before use.

Application
The area to be glued or filled must be clean, perfectly dry and dust free.
USE: Spatula. Add to the mastic 2% of hardener, in weight, mix until a
homogeneous mass is obtained and apply with a spatula on horizontal or
vertical surface. After a couple of hours, the mastic can be grinded and polished.
Dilution : Don't dilute, it is ready to use.

Thassos
Use for

Function

Polyester white mastic.

Makrana, White Marble of Carrara, Thassos

Features
The product color is at all similar to white marble form Greece. The resin, reacting with the
special catalyzer, becomes exactly like the marble. It has an optimum resistance to UV rays.

Suggestions

Application

It is possible to use an higher or lower % of catalyzer

to quicken or slow down the catalysis.
Read carefully recommendations printed on the tin
before use.

The area to be glued or filled must be clean, perfectly dry and dust free.
USE: Spatula. Add to the mastic 2% of hardener, in weight, mix until a homogeneous
mass is obtained and apply with a spatula on horizontal or vertical surface.
After a couple of hours, the mastic can be grinded and polished.
Dilution : Don't dilute, it is ready to use.

Blitz
Function

High resistance epoxyvinylester mastic.

Use for

Makrana, Granite, Ceramic, Concrete

Features
Created thanks to the usage of new concept resins, this mastic has an exceptional strength and fast
application most suitable to glue and fill many types of marble. It has best the mix between the
mechanical and chemical properties of the epoxy resin and the dry time of the polyester resins. It
works in very exceptional short time. It has also an excellent resistance to chemical attacks. Three
different color: transparent, white, light straw yellow.

Suggestions
It is possible to use an higher or lower % of catalyzer to quicken or slow down the catalysis. It is
possible to color the mastic with appropriate coloring tubes.
Read carefully recommendations printed on the tin before use.

Application
The area to be glued or filled must be clean, perfectly dry (or, eventually, slightly
humid). USE: Spatula. Add to the mastic 2% of hardener, in weight, mix until a
homogeneous mass is obtained and apply with a spatula on horizontal or vertical
surface. After a couple of hours, the mastic can be grinded and polished.
Dilution : Don't dilute, it is ready to use.

Astra 24K
Function

Clear transparent polyester mastic glass effect.

Use for

Marble, Travertine, Terrazzo

Features
Super transparent two-component mastic for glue and filling marble and stone. For its
adhesive good power and its unbeatable transparency, it is indispensable for marble
and light colored stone like Travertine, whenever the characteristic holes need to be
seen. Available in liquid and solid version.

Application

Suggestions
It is possible to use an higher or lower % of catalyzer to quicken or slow down the catalysis. It is
possible to color the mastic with appropriate coloring tubes.
Read carefully recommendations printed on the tin before use.

The area to be glued or filled must be clean, perfectly dry and dust free.
USE: Spatula. Add to the mastic 2% of hardener, in weight, mix until a
homogeneous mass is obtained and apply with a spatula on horizontal or
vertical surface. After a couple of hours, the mastic can be grinded and polished.
Dilution : Don't dilute, it is ready to use.

Function

Two-component epoxy mastic.

Features

Use for

Marble, Granite, Agglomerates, Marble Resin,

Terrazzo, Calcareous Stones

Studied for hard and crystalline stones where standard polyester mastic are not indicated. Its higher adhesive
power makes it useful to fill or rectify also big imperfections on works that otherwise would be considered
waste. Weather-proof and with a very high resistance to oils, greases, detergents, solvent and marine water.
Types available: liquid (transparent) and tixo (transparent, straw yellow and white).

ADHESIVES

Epox 2000

Application

Suggestions
Humidity can change the reaction time of catalysis. Don't use the coloring paste more than 2%
in weight, it could prejudice the adhesion. Part A and part B should be taken with different
spatulas. Working tools can be washed with nitro thinner.
Read carefully recommendations printed on the tin before use.

The area to be glued or filled must be clean, perfectly dry and dust free.
USE: spatula. Mix 2 parts of product A with one part of product B, using
a agitator until an uniform paste is obtained. Work with small quantity of product
at one time to avoid mass effect. Don't work below 10C.
Dilution : Don't dilute, it is ready to use.

Imprepox / Easypox
Function

Very high fluidity transparent epoxy impregnator.

Use for

Marble, Granite, Agglomerates, Marble Resin

Features
It seals and fills micro cracks capillaries in expensive marble and granite, which, if not repaired perfectly, are to be wasted. It reinforces
the backside of natural stone slabs subject to breakage. It offers hardness and flexibility, best resistance to chemicals and solvents, it
gives particular adhesion and shining after polishing.Totally transparent, ideal for clear marbles.

Suggestions
Humidity can change the catalysis time. Part A and part B should be taken with different
spatulas. Working tools can be washed with nitro thinner.
Read carefully recommendations printed on the tin before use.

Application
The area to be glued or filled must be clean, perfectly dry and dust free.
USE: Spatula. Mix 4 parts of product A with 1 part of product B, until an uniform paste is
obtained. Spread the mix on the surface with a spatula. Take small amount of product in
order to avoid mass effect. Don't work below 15C.
Dilution : Don't dilute, it is ready to use.

Special Preparato
Function

Paste Wax for polishing.

Use for

Marble, Granite, Marble Resin, Terrazzo

Features
A top quality concentrated wax dissolved in an non-inflammable solvent. Exceptional polishing and
protective power It provides an uniform brilliant and long lasting mirror finish. It fills and seals porosities
and cover small scratches. Available in the following colors: neutral, red, green, yellow, brown and black.

Suggestions
The longer the wax dries on the surface the better the final result will be.
Don't apply on linoleum, rubber, plastic. Heating the slab before the
application will allow a better wax penetration and therefore a better final result.
Read carefully recommendations printed on the tin before use.

Coverage

SHINERS

For polished marble and granite with 1Kg of product it is possible to treat 40-50 sqm.
In case of polished calcareous stone, limestone, sandstone, concrete polished after grid
800 with 1kg of product it is possible to treat 20-35 sqm.

Application
Surface must be clean & dry.
Use: cloth.
Apply the product on the surface & distribute homogeneously with a clean cloth.
Let it dry for 10 minutes. For manual polish is suggested to use fine steel wool, or an
electrical flex machine at low speed (max 2.000 rpm)equipped with felt disc or cloth.

Special Liquido
Function

Liquid polishing and enhancing wax for corners and edges.

Use for

Marble, Granite, Marble Resin, Terrazzo

Features
The product polishes, intensifies and enchances color giving the stone an attractive wet look. It will
not leave an anti-esthetic film and will not become yellow. Exceptionally useful for corners, edges and
areas where mechanical polishing is very difficult. It dries and polishes easily. It is ideal for rough and
semi-polished materials.

Suggestions
The longer the wax stays the better the final result will be. Don't apply on linoleum rubber,
plastic. Read carefully recommendations printed on the tin before use.

Coverage
For polished marble and granite with 1 kg of product it is possible to treat 10-25 sqm. In case of
polished calcareous stone, limestone, sandstone, concrete polished after grid 800, with 1 kg of
product it is possible to treat 15-25 sqm. For more absorbent materials coverage is 10-15 sqm
with one liter of product.

Application
Surface must be clean and dry.
Use: clean cloth, flex machine.
Apply the product & distribute homogeneously. Let it dry for 10 minutes.
For manual polish is suggested to use fine steel wool, or use an electrical flex
machine at low speed (max 2.000 rpm) equipped with felt disc or cloth.

VX-SL

Function

Liquid Silicone Wax.

Use for

Marble, Granite, Marble Resin, Gres and Ceramic, Terrazzo, Calcareous Stones
Features
Liquid wax with a special modified silicone that dries very quickly. Specially formulated to
use with automatic waxing machines. It can be used by hand to polish & protect internal
& external walls, skirting, risers, and monuments. It gives color and shine on any type of
stone grinded over grid 800.

Suggestions

Application

Use: cloth or electrical flex machine.

Application by hand: apply on the surface clean and dry (wash with Detergent Lem-3 or
Ultra Stripper). Let it dry for 10 minutes. Buff with a dry soft clean cloth, by brush or
electrical flex machine (max 2000rpm) equipped with felt disc.
Coverage
Application by automatic machine: the production line needs an automatic waxing machine
equipped with electric fan to dry the material before waxing, an automatic barching-timing
For polishing marble & granite polished or grinded after grid 800, with 1 kg of product is plant to regulate wax emission, a waxing machine heads for distribution of the wax, an
possible to treat 25-50 sqm. In case of calcareous stone, limestone, sandstone, concrete electric fan drying the newly spread wax and two polishing machine heads with large
polished or grinded after grid 800 with 1 kg of product it is possible to treat 15-40 sqm. brushes to polish the material.
Don't apply on linoleum rubber, plastic.
Read carefully recommendations printed on the tin before use.

Function

Repolishable liquid wax.

Use for

Marble, Granite, Marble Resin, Terrazzo

Features
Water based liquid wax based on natural and synthetic waxes. It gives a brilliant and warm shining.
The wax is highly concentrated and can be widely diluted in water, making it very economical to use.
Once applied, it has good resistance to washing when regular detergents are used. It is also
pleasantly perfumed.

Suggestions
Only for internal use. The longer the wax dries on the surface the better the fine result will be.
Always dilute the wax in order to avoid build-up on the floor.
Read carefully recommendations printed on the tin before use.

Coverage
With 1 liter of product it is possible to treat 70-150 sqm.

Dilution
Dilute the product in water 1:20
(1 dosing cap in 1ltr. of water)

Application
Wash well the floor with Detergent Lem-3
Use: cloth, mop, fleece, wool cloth or floor-polishing machine .
Apply evenly and let it dry while avoiding walk on it. Do not walk on it till dried.
Polish energetically with a dry cloth or use a floor-polishing machine.
Periodical floor washing must be done with water and Detergent Lem-3.

SHINERS

RR1

Mangiaruggine
Function

Removes rust and oxidations without altering the stone shine.

Features
It removes stains of rust without damaging marble, because it is not an acid product. It acts quickly and it
removes rust without effort. Its gel formulation allows its use on vertical surfaces.

Suggestions
Make a test before use. If necessary, repeat the application.
Read carefully recommendations printed on the tin before use.

Coverage
With 1 liter of product it is possible to treat 10 sqm, depending on material and porosity.

CLEANERS

Application
USE: plastic spatula.
Apply a 5 mm layer on the area with a plastic spatula and let it dry.
The product changes its color from original opalescent into opaque dark violet.
Rinse with abundant water, within 3 minutes form the color change.
Dilution : Don't dilute, it is ready to use.

Mangiamacchia
Function

Absorbing paste formulated to remove stubborn stains.

Features
It removes stubborn stains of oil, industrial oil, edible oil, coffee.
It penetrates deeply into the stone, it does not damage the stone and does not leave shades. It removes humidity
sports, salts and saltpeter.

Suggestions
Paste must adhere to substrate to improve effect.If necessary, repeat the application.
Read carefully recommendations printed on the tin before use.

Coverage
With 1 liter of product it is possible to treat 7-20 sqm based on the absorption of the stone

Application
USE: Spatula.
Apply a layer of 5 mm approx on the area with a spatula. Cover with a plastic film and remove after 2-3 hours.
Let the paste dry naturally. After 8-10 hours the paste will appear like dry whitish mud.
Remove it with a brush and clean with detergent Lem 3.
Dilution : Don't dilute, it is ready to use.

Lem-3
Function

Concentrated neutral cleaner.

Use for

Marble, Granite, Terrazzo, Ceremic, Calcareous Stones

Features
Concentrate detergent for resistant dirt.
It cleans and washes all cleanable surfaces, suitable also for glass.

Suggestions
For periodical maintenance: 30-50 ml in 1 liter of water.
For heavy dirt: 100 ml in 1 liter of water.
Read carefully recommendations printed on the tin before use.

Coverage
With 1 liter it is possible to treat 100-150 sqm, depending on dilution.

Application
USE: cloth or mop.
Apply and wait 10 minutes and rub with scrubbing brush or
use a single disc machine. Let dry and for very resistant soil repeat application.
Let the floor dry before walking on it.

CLEANERS

Bert 27
Function

Extra strong acid based detergent.

Use for

Granite, Ceramic, Concrete

Features
Very concentrate acid based cleaner for every type of in organic dirt. Excellent against rust.
Ideal to clean floor with greasy and oily dirt, mortar residuals and saltpetre efflorecences. It is
also suitable for clearing street and cimiterial furnitures.

Suggestions
Wash thoroughly with water all tools that have been used. Do not use Bert 27 on marble,
calcareous stones and any other acid sensitive material.
Read carefully recommendations printed on the tin before use.

Coverage
With 1 liter it is possible to treat 80-150 sqm, depending on dilution.

Dilution
Dilute the product with water, depending on the amount of dirt to be removed.

Application
Shake it before using.
USE: mop, cloth or single disc machine.
Let it work for 5-10 minutes.
Rub with brush or single disc machine with abrasive pads.
Rinse the floor very well with water and alkaline detergent,
then pass the vacuum cleaner to remove dirty water.

10, Dhuleshwar Garden Jaipur-302001 INDIA

Tel.: +91-141-5164444 Fax: +91-141-2361933
E-mail: info@truworth.in Web: www.truworth.in
Customer Support : +91-9875-000-333

MUMBAI
Office No. 1005 Jai Antriksh
Makwana Road, Marol,
Andheri (E), Mumbai 400 059

DELHI
Khasra no-416/2, Opp. Metro pillar no-127,
Ground Floor, M.G.Road, Ghitorni,
New Delhi 110 030

BANGALORE
1st Floor, R. K. Lake Towers,
Outer Ring Road, Hebbal
Bangalore, Karnataka 560 024