Power Distribution System

Power Distribution Systems
1.0-1
April 2016
Power Distribution
Systems
Sheet 01 001
Contents
System Design
Basic Principles. . . . . . . . . . . 1.1-1
Modern Electric Power
Technologies . . . . . . . . . . . 1.1-1
Goals of System Design . . . 1.1-2
Voltage Classifications; BILs
Basic Impulse Levels . . . . . 1.1-3
Three-Phase Transformer
Winding Connections . . . . 1.1-5
Types of SystemsRadial,
Loop, Selective, Two-Source,
Sparing Transformer, Spot
Network, Distribution . . . . 1.1-6
Health Care Facility
Design Considerations . . . 1.1-15
Generator Systems . . . . . . 1.1-18
Generator System Design
Types of Generators. . . . . . . 1.2-1
Generator Systems . . . . . . . 1.2-2
Generator Grounding. . . . . . 1.2-3
Generator Controls. . . . . . . . 1.2-4
Generator Short-Circuit
Characteristics . . . . . . . . . . 1.2-4
Generator Protection . . . . . . 1.2-5
System Analysis
Systems Analysis . . . . . . . . . 1.3-1
Short-Circuit Currents . . . . . 1.3-2
Fault Current Waveform
Relationships . . . . . . . . . . . 1.3-3
Fault Current Calculations
and Methods Index . . . . . . 1.3-4
Determine X and R from
Transformer Loss Data . . . 1.3-19
Voltage Drop
Considerations . . . . . . . . . . 1.3-20
System Application Considerations
Capacitors and
Power Factor . . . . . . . . . . . 1.4-1
Overcurrent Protection
and Coordination . . . . . . . . 1.4-3
Protection of Conductors. . . 1.4-5
Circuit Breaker Cable
Temperature Ratings . . . . . 1.4-5
Zone Selective Interlocking . 1.4-5
Ground Fault Protection . . . 1.4-6
i
Suggested Ground
Fault Settings. . . . . . . . . . . . . 1.4-6
Grounding/Ground Fault Protection
GroundingEquipment,
System, MV System,
LV System . . . . . . . . . . . . . . 1.4-9
Ground Fault Protection . . . . 1.4-11
Lightning and Surge
Protection . . . . . . . . . . . . . . 1.4-14
Grounding Electrodes . . . . . 1.4-14
MV Equipment Surge
Protection Considerations . 1.4-14
Surge Protection . . . . . . . . . . 1.4-14
Types of Surge
Protection Devices . . . . . . . 1.4-15
Power Quality
Terms, Technical Overview . . 1.4-18
SPD . . . . . . . . . . . . . . . . . . . . 1.4-19
Harmonics and
Nonlinear Loads . . . . . . . . . 1.4-21
UPS . . . . . . . . . . . . . . . . . . . . 1.4-25
Other Application Considerations
Secondary Voltage . . . . . . . . 1.4-31
Energy Conservation . . . . . . 1.4-32
Building Control Systems . . 1.4-33
Distributed Energy
Resources . . . . . . . . . . . . . . 1.4-33
Cogeneration . . . . . . . . . . . . 1.4-33
PV System Design
Considerations . . . . . . . . . . 1.4-34
Emergency Power. . . . . . . . . 1.4-35
Peak Shaving. . . . . . . . . . . . . 1.4-36
Sound Levels. . . . . . . . . . . . . 1.4-36
Reference Data
IEEE Protective Relay
Numbers . . . . . . . . . . . . . . . 1.5-1
Codes and Standards . . . . . . 1.5-6
Motor Protective
Device Data. . . . . . . . . . . . . 1.5-7
Chart of Short-Circuit
Currents for Transformers . . 1.5-9
Transformer Full Load
Amperes . . . . . . . . . . . . . . . 1.5-10
Impedances Data . . . . . . . . . 1.5-11
Transformer Losses . . . . . . . 1.5-12
Power Equipment Losses . . . 1.5-13
NEMA Enclosure Definitions. . 1.5-13
Cable R, X, Z Data . . . . . . . . . 1.5-15
Conductor Ampacities . . . . . 1.5-17
Conductor Temperature
Ratings . . . . . . . . . . . . . . . . 1.5-17
Formulas and Terms. . . . . . . 1.5-20
Seismic Requirements . . . . . 1.5-21
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Designing a Distribution System
CA08104001E
For more information, visit: www.eaton.com/consultants
21
1.0-2

April 2016
Sheet 01 002
This page intentionally left blank.
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

System Design
April 2016
1.1-1
Sheet 01 003
Basic Principles
The best distribution system is one
that will, cost-effectively and safely,
supply adequate electric service to
both present and future probable
loadsthis section is included to aid
in selecting, designing and installing
such a system.
The function of the electric power
distribution system in a building or
an installation site is to receive power
at one or more supply points and
to deliver it to the individual lamps,
motors and all other electrically
operated devices. The importance
of the distribution system to the
function of a building makes it almost
imperative that the best system be
designed and installed.
In order to design the best distribution
system, the system design engineer
must have information concerning the
loads and a knowledge of the various
types of distribution systems that are
applicable. The various categories of
buildings have many specific design
challenges, but certain basic principles
are common to all. Such principles,
if followed, will provide a soundly
executed design.
The basic principles or factors requiring

consideration during design of the
power distribution system include:
Modern Electric Power

Technologies
Several new factors to consider in

modern power distribution systems
result from two relatively recent
changes. The first recent change is
utility deregulation. The traditional
dependence on the utility for problem
analysis, energy conservation measurements and techniques, and a
simplified cost structure for electricity
has changed. The second change is less
obvious to the designer yet will have
an impact on the types of equipment
and systems being designed. It is the
diminishing quantity of qualified building electrical operators, maintenance
departments and facility engineers.
Functions of structure, present

and future
Life and flexibility of structure
Locations of service entrance and
distribution equipment, locations
and characteristics of loads,
locations of unit substations
Demand and diversity factors
of loads
Sources of power; including
normal, standby and emergency
(see Tab 40)
Continuity and quality of
power available and required
(see Tab 33)
Energy efficiency and management
Distribution and utilization voltages
Bus and/or cable feeders
Distribution equipment and
motor control
Power and lighting panelboards
and motor control centers
Types of lighting systems
Installation methods
Power monitoring systems
Electric utility requirements
Modern electric power technologies

may be of use to the designer and
building owner in addressing these
new challenges. The advent of microprocessor devices (smart devices)
into power distribution equipment has
expanded facility owners options and
capabilities, allowing for automated
communication of vital power system
information (both energy data and
system operation information) and
electrical equipment control.
These technologies may be grouped as:
Power monitoring and control

Building management systems
interfaces
Lighting control
Automated energy management
Predictive diagnostics
Various sections of this guide cover

the application and selection of such
systems and components that may be
incorporated into the power equipment
being designed. See Tabs 2, 3, 4, 23
and 41.
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E
1.1-2

System Design
April 2016
Sheet 01 004
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Goals of System Design

When considering the design of an
electrical distribution system for
a given customer and facility, the
electrical engineer must consider
alternate design approaches that
best fit the following overall goals.
1. Safety: The No. 1 goal is to design
a power system that will not
present any electrical hazard to
the people who use the facility,
and/or the utilization equipment
fed from the electrical system.
It is also important to design a
system that is inherently safe for
the people who are responsible for
electrical equipment maintenance
and upkeep.
The National Electrical Code
(NEC), NFPA 70 and NFPA 70E,
as well as local electrical codes,
provide minimum standards and
requirements in the area of wiring
design and protection, wiring
methods and materials, as well
as equipment for general use with
the overall goal of providing safe
electrical distribution systems
and equipment.
The NEC also covers minimum
requirements for special
occupancies including hazardous
locations and special use type
facilities such as health care
facilities, places of assembly,
theaters and the like, and the
equipment and systems located in
these facilities. Special equipment
and special conditions such as
emergency systems, standby
systems and communication
systems are also covered in
the code.
It is the responsibility of the design
engineer to be familiar with the
NFPA and NEC code requirements
as well as the customers facility,
process and operating procedures;
to design a system that protects
personnel from live electrical
conductors and uses adequate
circuit protective devices that will
selectively isolate overloaded or
faulted circuits or equipment as
quickly as possible.
2. Minimum Initial Investment:

The owners overall budget for
first cost purchase and installation
of the electrical distribution system and electrical utilization
equipment will be a key factor
in determining which of various
alternate system designs are to be
selected. When trying to minimize
initial investment for electrical
equipment, consideration should
be given to the cost of installation,
floor space requirements and
possible extra cooling requirements as well as the initial
purchase price.
3. Maximum Service Continuity:
The degree of service continuity
and reliability needed will vary
depending on the type and use
of the facility as well as the loads
or processes being supplied by the
electrical distribution system. For
example, for a smaller commercial
office building, a power outage
of considerable time, say several
hours, may be acceptable, whereas
in a larger commercial building or
industrial plant only a few minutes
may be acceptable. In other facilities
such as hospitals, many critical
loads permit a maximum of
10 seconds outage and certain
loads, such as real-time computers,
cannot tolerate a loss of power for
even a few cycles.
Typically, service continuity and
reliability can be increased by:
A. Supplying multiple utility power
sources or services.
B. Supplying multiple connection
paths to the loads served.
4. Maximum Flexibility and

Expendability: In many industrial
manufacturing plants, electrical
utilization loads are periodically
relocated or changed requiring
changes in the electrical distribution system. Consideration of
the layout and design of the
electrical distribution system to
accommodate these changes must
be considered. For example, providing many smaller transformers
or loadcenters associated with a
given area or specific groups of
machinery may lend more flexibility
for future changes than one large
transformer; the use of plug-in
busways to feed selected equipment in lieu of conduit and wire
may facilitate future revised
equipment layouts.
In addition, consideration must be
given to future building expansion,
and/or increased load requirements due to added utilization
equipment when designing the
electrical distribution system.
In many cases considering transformers with increased capacity
or fan cooling to serve unexpected
loads as well as including spare
additional protective devices and/
or provision for future addition of
these devices may be desirable.
Also to be considered is increasing
appropriate circuit capacities or
quantities for future growth.
Power monitoring communication
systems connected to electronic
metering can provide the trending
and historical data necessary for
future capacity growth.
C. Using short-time rated power

circuit breakers.
D. Providing alternate customerowned power sources such as
generators or batteries supplying
uninterruptable power supplies.
E. Selecting the highest quality electrical equipment and conductors.
F. Using the best installation methods.
G. Designing appropriate system
alarms, monitoring and diagnostics.
H. Selecting preventative maintenance systems or equipment to
alarm before an outage occurs.
20
21
CA08104001E
April 2016

System Design
1.1-3
Sheet 01 005
5. Maximum Electrical Efficiency

(Minimum Operating Costs):
Electrical efficiency can generally
be maximized by designing
systems that minimize the losses
in conductors, transformers and
utilization equipment. Proper
voltage level selection plays a
key factor in this area and will
be discussed later. Selecting
equipment, such as transformers,
with lower operating losses,
generally means higher first cost
and increased floor space requirements; thus, there is a balance
to be considered between the
owners utility energy change
for the losses in the transformer
or other equipment versus the
owners first cost budget and
cost of money.
6. Minimum Maintenance Cost:
Usually the simpler the electrical
system design and the simpler
the electrical equipment, the less
the associated maintenance costs
and operator errors. As electrical
systems and equipment become
more complicated to provide
greater service continuity or
flexibility, the maintenance costs
and chance for operator error
increases. The systems should be
designed with an alternate power
circuit to take electrical equipment
(requiring periodic maintenance)
out of service without dropping
essential loads. Use of drawout
type protective devices such as
breakers and combination starters
can also minimize maintenance
cost and out-of-service time.
Utilizing sealed equipment in
lieu of ventilated equipment may
minimize maintenance costs and
out-of-service time as well.
7. Maximum Power Quality:

The power input requirements
of all utilization equipment has
to be considered including the
acceptable operating range of
the equipment and the electrical
distribution system has to be
designed to meet these needs.
For example, what is the required
input voltage, current, power
factor requirement? Consideration to whether the loads are
affected by harmonics (multiples
of the basic 60 Hz sine wave) or
generate harmonics must be taken
into account as well as transient
voltage phenomena.
The above goals are interrelated
and in some ways contradictory.
As more redundancy is added to
the electrical system design along
with the best quality equipment
to maximize service continuity,
flexibility and expandability, and
power quality, the more initial
investment and maintenance
are increased. Thus, the designer
must weigh each factor based
on the type of facility, the loads
to be served, the owners past
experience and criteria.
Summary
It is to be expected that the engineer
will never have complete load information available when the system is
designed. The engineer will have to
expand the information made available to him on the basis of experience
with similar problems. Of course, it
is desirable that the engineer has as
much definite information as possible
concerning the function, requirements,
and characteristics of the utilization
devices. The engineer should know
whether certain loads function
separately or together as a unit, the
magnitude of the demand of the loads
viewed separately and as units, the rated
voltage and frequency of the devices,
their physical location with respect
to each other and with respect to the
source and the probability and possibility of the relocation of load devices
and addition of loads in the future.
Coupled with this information, a

knowledge of the major types of electric
power distribution systems equips the
engineers to arrive at the best system
design for the particular building.
It is beyond the scope of this guide to
present a detailed discussion of loads
that might be found in each of several
types of buildings. Assuming that the
design engineer has assembled the
necessary load data, the following
pages discuss some of the various
types of electrical distribution systems
that can be used. The description of
types of systems, and the diagrams
used to explain the types of systems
on the following pages omits the
location of utility revenue metering
equipment for clarity. A discussion of
short-circuit calculations, coordination,
voltage selection, voltage drop, ground
fault protection, motor protection and
other specific equipment protection
is also presented.
i
ii
1
2
3
4
5
6
7
Voltage Classifications
ANSI and IEEE standards define
various voltage classifications for
single-phase and three-phase systems.
The terminology used divides voltage
classes into:
Low voltage
Medium voltage
High voltage
Extra-high voltage
Ultra-high voltage
8
9
10
Table 1.1-1 presents the nominal system

voltages for these classifications.
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

System Design
1.1-4
April 2016
Sheet 01 006
Table 1.1-1. Standard Nominal System

Voltages and Voltage Ranges
(From IEEE Standard 141-1993)
ii
Voltage
Class
Low
voltage
Nominal System Voltage

Three-Wire Four-Wire
Table 1.1-6. Dry-Type Transformers Voltage

and Basic Lightning Impulse Insulation
Levels (BIL)From ANSI/IEEE C57.12.01-1998)
Table 1.1-4. Pad Mounted and Overhead

Distribution Switchgear, Voltage and
Insulation Levels
Rated Maximum
Impulse
Voltage Level (kV rms) Withstand (kV)
Pad Mount Switchgear (per IEEE C37.74-2014)
Medium
voltage
3
4
5
6
7
8
9
High
voltage
11
12
2400
4160
4800
6900
13,200
13,800
23,000
34,500
46,000
69,000
208Y/120
240/120
480Y/277
4160Y/2400
8320Y/4800
12000Y/6930
12470Y/7200
13200Y/7620
13800Y/7970
20780Y/12000
22860Y/13200
24940Y/14400
34500Y/19920
115,000
138,000
161,000
230,000
Extra-high
voltage
345,000
500,000
765,000
Ultra-high
voltage
1,100,000
15.5
27
38
15
15.5
27
95
110
125
38
38
150
170
1.2
2.5
5.0
8.7
15.0
25.0
34.5
2
Table 1.1-5. Liquid-Immersed

Transformers Voltage and Basic
Lightning Impulse Insulation Levels (BIL)
(From ANSI/IEEE C57.12.00)
Application
Nominal
System
Voltage
(kV rms)
Distribution
1.2
2.5
5.0
30
45
60
8.7
15.0
25.0
75
95
150
34.5
46.0
69.0
200
250
350
1.2
2.5
5.0
45
60
75
30
45
60
8.7
15.0
25.0
95
110
150
75
95
34.5
46.0
69.0
200
250
350
200
250
ANSI standards define recommended

and required BIL levels for:
Metal-clad switchgear
(typically vacuum breakers)
Metal-enclosed switchgear (typically
load interrupters, switches)
Pad-mounted and overhead
distribution switchgear
Liquid immersed transformers
Dry-type transformers
95
125
150
Overhead Switchgear (per IEEE C37.60-2012)
BILBasic Impulse Levels
10
240/120
240
480
600
Power
BIL
(kV Crest) 1
150 125
200
250
14
17
18
27.0
38.0
125
150
20
110
150
200
BIL values in bold typeface are listed as

standard. Others listed are in common use.
Optional higher levels used where exposure
to overvoltage occurs and higher protection
margins are required.
Lower levels where surge arrester
protective devices can be applied with
lower spark-over levels.
450
550
650
350
450
550
BIL values in bold typeface are listed as

standard. Others listed are in common use.
Motor, motor starter and cable

first cost
Motor, motor starter and cable
installation cost
Motor and cable losses
Motor availability
Voltage drop
Qualifications of the building
operating staff; and many more
The following table is based in part

on the above factors and experience.
Because all the factors affecting the
selection are rarely known, it is only
an approximate guideline.
Table 1.1-7. Selection of Motor Horsepower
Ratings as a Function of System Voltage
Motor Voltage Motor
(Volts)
hp Range
System
Voltage
460
2300
4000
up to 500
250 to 2000
250 to 3000
480
2400
4160
4600
13,200
250 to 3000
above 2000
4800
13,800
Table 1.1-3. Metal-Enclosed Switchgear

Voltage and Insulation Levels
(From IEEE Std. C37.20.3-2013)
Rated Maximum
Voltage (kV rms)
19
95
125
150
900
825 750 650
1175 1050
900
1675 1550 1425 1300
2050 1925 1800
16
60
110
125 3
230.0
345.0
500.0
765.0
60
95
95
30
45
60
95
125
Table 1.1-2. Metal-Clad Switchgear

Voltage and Insulation Levels
(From IEEE Std. C37.20.2-2015)
4.76
8.25
15.0
20
30
45
60
Some factors affecting the selection

of motor operating voltage include:
550
650
750
95 3
10
20
30
45
115.0
138.0
161.0
15
Table 1.1-2 through Table 1.1-6 contain

those values.
Impulse
Withstand (kV)
BIL (kV Crest) 2
Voltage Recommendations by
Motor Horsepower
13
Rated Maximum
Voltage (kV rms)
Nominal
System
Voltage
(kV rms)
Impulse
Withstand (kV)
4.76
8.25
15.0
60
95
95
27.0
38.0
125
150
21
CA08104001E

System Design
April 2016
1.1-5
Sheet 01 007
Table 1.1-7. Three-Phase Transformer Winding Connections

Phasor
Diagram
Notes
1. Suitable for both ungrounded and effectively grounded sources.
2. Suitable for a three-wire service or a four-wire service with a mid-tap ground.
DELTA-DELTA Connection
Phasor
Diagram:
i
ii
X2
H2
H1
H3
X1
X3
Angular Displacement (Degrees): 0

DELTA-WYE Connection
Phasor
Diagram:
H2
X2
X0
X1
H1
H3
X3
WYE-DELTA Connection
Phasor
Diagram:
H2
X2
X1
H1
H3
X3
WYE-WYE Connection
Phasor
Diagram:
X2
H2
X0
H1
H3
X1
X3

2. Suitable for a three-wire service or a four-wire grounded service with
XO grounded.
3. With XO grounded, the transformer acts as a ground source for the
secondary system.
4. Fundamental and harmonic frequency zero-sequence currents in the secondary
lines supplied by the transformer do not flow in the primary lines. Instead the
zero sequence currents circulate in the closed delta primary windings.
5. When supplied from an effectively grounded primary system does not see load
unbalances and ground faults in the secondary system.
2. Suitable for a three-wire service or a four-wire delta service with a mid-tap ground.
3. Grounding the primary neutral of this connection would create a ground source
for the primary system. This could subject the transformer to severe overloading
during a primary system disturbance or load unbalance.
4. Frequently installed with mid-tap ground on one leg when supplying
combination three-phase and single-phase load where the three-phase
load is much larger than single-phase load.
5. When used in 25 kV and 35 kV three-phase four-wire primary systems,
ferroresonance can occur when energizing or de-energizing the transformer
using single-pole switches located at the primary terminals. With smaller kVA
transformers the probability of ferroresonance is higher.
2. Suitable for a three-wire service only, even if XO is grounded.
3. This connection is incapable of furnishing a stabilized neutral and its use may
result in phase-to-neutral overvoltage (neutral shift) as a result of unbalanced
phase-to-neutral load.
4. If a three-phase unit is built on a three-legged core, the neutral point of the
primary windings is practically locked at ground potential.
X2
H2
X0
H0
H1
H3
X1
X3
X2
H2
1. Suitable for four-wire effectively grounded source only.

2. Suitable for a three-wire service or for four-wire grounded service with
XO grounded.
3. Three-phase transformers with this connection may experience stray flux tank
heating during certain external system unbalances unless the core configuration
(four or five legged) used provides a return path for the flux.
4. Fundamental and harmonic frequency zero-sequence currents in the secondary
lines supplied by the transformer also flow in the primary lines (and primary
neutral conductor).
5. Ground relay for the primary system may see load unbalances and ground
faults in the secondary system. This must be considered when coordinating
overcurrent protective devices.
6. Three-phase transformers with the neutral points of the high voltage and low
voltage windings connected together internally and brought out through an
HOXO bushing should not be operated with the HOXO bushing ungrounded
(floating). To do so can result in very high voltages in the secondary systems.
2. Suitable for a three-wire service or a four-wire service with a mid-tap ground.
3. When using the tap for single-phase circuits, the single-phase load kVA should
not exceed 5% of the three-phase kVA rating of the transformer. The three-phase
rating of the transformer is also substantially reduced.
DELTA-DELTA Connection with Tap

Phasor
Diagram:
4
5
6
7
8
9
10
11
12
13
GROUNDED WYE-WYE Connection

Phasor
Diagram:
X4
14
15
16
17
18
19
20
H1
H3
X1
X3
21
CA08104001E
1.1-6

System Design
April 2016
Sheet 01 008
i
ii
1
2
3
4
5
6
7
8
Types of Systems
In many cases, power is supplied by
the utility to a building at the utilization
voltage. In these cases, the distribution
of power within the building is achieved
through the use of a simple radial
distribution system.
In cases where the utility service voltage
is at some voltage higher than the
utilization voltage within the building,
the system design engineer has a choice
of a number of types of systems that
may be used. This discussion covers
several major types of distribution
systems and practical modifications
of them.
1. Simple radial
2. Loop-primary system
radial secondary system
3. Primary selective system
secondary radial system
4. Two-source primary
secondary selective system
A fault on the secondary low voltage

bus or in the source transformer will
interrupt service to all loads. Service
cannot be restored until the necessary
repairs have been made. A low voltage
feeder circuit fault will interrupt service
to all loads supplied over that feeder.
Low voltage feeder circuits run from

the switchgear or switchboard assemblies to panelboards that are located
closer to their respective loads as
shown in Figure 1.1-1.
Each feeder is connected to the switchgear or switchboard bus through a
circuit breaker or other overcurrent
protective device. A relatively small
number of circuits are used to distribute
power to the loads from the switchgear or switchboard assemblies and
panelboards.
A modern and improved form of the

conventional simple radial system
distributes power at a primary voltage.
The voltage is stepped down to
utilization level in the several load
areas within the building typically
through secondary unit substation
transformers. The transformers are
usually connected to their associated
load bus through a circuit breaker, as
shown in Figure 1.1-2. Each secondary
unit substation is an assembled unit
consisting of a three-phase, liquidfilled or air-cooled transformer, an integrally connected primary fused switch,
and low voltage switchgear or switchboard with circuit breakers or fused
switches. Circuits are run to
the loads from these low voltage
protective devices.
Because the entire load is served from

a single source, full advantage can be
taken of the diversity among the loads.
This makes it possible to minimize the
installed transformer capacity. However,
the voltage regulation and efficiency
of this system may be poor because
of the low voltage feeders and single
source. The cost of the low voltagefeeder circuits and their associated circuit
breakers are high when the feeders are
long and the peak demand is above
1000 kVA.
5. Sparing transformer system

6. Simple spot network
9
10
11
12
13
14
15
16
17
18
19
20
21
7. Medium voltage distribution

system design
Primary Fused Switch

Transformer
1. Simple Radial System

The conventional simple radial system
receives power at the utility supply
voltage at a single substation and steps
the voltage down to the utilization level.
In those cases where the customer
receives his supply from the primary
system and owns the primary switch
and transformer along with the secondary low voltage switchboard or switchgear, the equipment may take the form
of a separate primary switch, separate
transformer, and separate low voltage
switchgear or switchboard. This equipment may be combined in the form of
an outdoor pad-mounted transformer
with internal primary fused switch
and secondary main breaker feeding
an indoor switchboard.
600V Class
Switchboard
Distribution
Dry-Type
Transformer
Distribution
Panel
MCC
Distribution
Panel
Lighting
Panelboard
Figure 1.1-1. Simple Radial System
52 Primary Main Breaker
52 52 52 52 52 52 Primary Feeder Breakers
Another alternative would be a

secondary unit substation where
the primary fused switch, transformer
and secondary switchgear or switchboard are designed and installed as
a close-coupled single assembly.
In those cases where the utility owns
the primary equipment and transformer,
the supply to the customer is at the
utilization voltage, and the service
equipment then becomes low voltage
main distribution switchgear or
a switchboard.
Primary
Cables
Secondary Unit
Substation
Figure 1.1-2. Primary and Secondary Simple Radial System

CA08104001E
April 2016

System Design
1.1-7
Sheet 01 009
Because each transformer is located

within a specific load area, it must
have sufficient capacity to carry the
peak load of that area. Consequently,
if any diversity exists among the load
area, this modified primary radial
system requires more transformer
capacity than the basic form of the
simple radial system. However,
because power is distributed to the
load areas at a primary voltage, losses
are reduced, voltage regulation is
improved, feeder circuit costs are
reduced substantially, and large
low voltage feeder circuit breakers
are eliminated. In many cases the
interrupting duty imposed on the
load circuit breakers is reduced.
In addition, if only one primary fuse on

a circuit opens, the secondary loads are
then single phased, causing damage to
low voltage motors.
This modern form of the simple radial

system will usually be lower in initial
investment than most other types of
primary distribution systems for buildings in which the peak load is above
1000 kVA. A fault on a primary feeder
circuit or in one transformer will cause
an outage to only those secondary
loads served by that feeder or transformer. In the case of a primary main
bus fault or a utility service outage,
service is interrupted to all loads until
the trouble is eliminated.
2. Loop Primary System

Radial Secondary System
Reducing the number of transformers

per primary feeder by adding more
primary feeder circuits will improve
the flexibility and service continuity
of this system; the ultimate being one
secondary unit substation per primary
feeder circuit. This of course increases
the investment in the system but
minimizes the extent of an outage
resulting from a transformer or
primary feeder fault.
Another approach to reducing costs

is to eliminate the primary feeder
breakers completely, and use a single
primary main breaker or fused switch
for protection of a single primary
feeder circuit with all secondary unit
substations supplied from this circuit.
Although this system results in less initial equipment cost, system reliability is
reduced drastically because a single
fault in any part of the primary conductor
would cause an outage to all loads
within the facility.
CA08104001E
When pad-mounted compartmentalized transformers are used, they are

furnished with loop-feed oil-immersed
gang-operated load break sectionalizing switches and Bay-O-Net expulsion
fuses in series with partial range backup current-limiting fuses. By operating
the appropriate sectionalizing switches,
it is possible to disconnect any section
of the loop conductors from the rest
of the system. In addition, it is possible
to disconnect any transformer from
the loop.
This system consists of one or more

PRIMARY LOOPS with two or more
transformers connected on the loop.
This system is typically most effective
when two services are available from
the utility as shown in Figure 1.1-3. Each
primary loop is operated such that one
of the loop sectionalizing switches is
kept open to prevent parallel operation
of the sources. When secondary unit
substations are used, each transformer
may have its own duplex (2-load break
switches with load side bus connection)
A key interlocking scheme is normally

recommended to prevent closing all
sectionalizing devices in the loop. Each
primary loop sectionalizing switch and
the feeder breakers to the loop are
interlocked such that to be closed they
require a key (which is held captive
until the switch or breaker is opened)
and one less key than the number of
key interlock cylinders is furnished.
An extra key is provided to defeat the
interlock under qualified supervision.
i
ii
1
2
3
4
5
6
7
8
9
10
11
Primary Main Breaker 1 52
52 Primary Main Breaker 2
12
52
52
52
Tie
Breaker
52
52
Loop Feeder Breaker
13
Loop A
Loop B
Primary connections from one secondary

unit substation to the next secondary
unit substation can be made with
double lugs on the unit substation
primary switch as shown, or with
separable connectors made in
manholes or other locations.
Depending on the load kVA connected
to each primary circuit and if no ground
fault protection is desired for either the
primary feeder conductors and transformers connected to that feeder or
the main bus, the primary main and/or
feeder breakers may be changed to
primary fused switches. This will significantly reduce the first cost, but also
decrease the level of conductor and
equipment protection. Thus, should
a fault or overload condition occur,
downtime increases significantly and
higher costs associated with increased
damage levels and the need for fuse
replacement is typically encountered.
sectionalizing switches and primary

load break fused switch as shown
in Figure 1.1-4 or utilizing three
on-off switches or a four-position
sectionalizing switch and vacuum
fault interrupter (VFI) internal to the
transformer saving cost and reducing
footprint.
NC
NO
NC
14
NC
Fault Sensors
15
16
NC
NC
NO
NC
NC
NC
17
18
19
Secondary Unit Substations Consisting of:

Duplex Primary Switches/Fused Primary Switches/
Transformer and Secondary Main Feeder Breakers
Figure 1.1-3. Loop PrimaryRadial Secondary System

20
21
1.1-8

System Design
April 2016
Sheet 01 010
Loop
Feeder
Loop
Feeder
Load Break
Loop Switches
ii
1
Fused
Disconnect
Switch
2
3
4
5
6
Figure 1.1-4. Secondary Unit Substation

Loop Switching
Main Source
Alternate Source
3-Position
Selector Switch
Vacuum Fault
Interrupter (VFI)
8
9
10
11
12
13
In addition, the two primary main

breakers, which are normally closed,
and primary tie breaker, which is
normally open, are either mechanically
or electrically interlocked to prevent
paralleling the incoming source lines.
For slightly added cost, an automatic
throw-over scheme can be added
between the two main breakers and
tie breaker. During the more common
event of a utility outage, the automatic
transfer scheme provides significantly
reduced power outage time.
The system in Figure 1.1-3 has higher
costs than in Figure 1.1-2, but offers
increased reliability and quick restoration of service when 1) a utility outage
occurs, 2) a primary feeder conductor
fault occurs, or 3) a transformer fault
or overload occurs.
15
Note: Under this condition, all secondary

unit substations are supplied through the
other loop feeder circuit breaker, and thus
all conductors around the loop should be
sized to carry the entire load connected to
the loop. Increasing the number of primary
loops (two loops shown in Figure 1.1-8)
will reduce the extent of the outage from a
conductor fault, but will also increase the
system investment.
Should a utility outage occur on one of

the incoming lines, the associated primary main breaker is opened and the
tie breaker closed either manually or
through an automatic transfer scheme.
When a transformer fault or overload

occurs, the transformer primary fuses
open, and the transformer primary
switch manually opened, disconnecting
the transformer from the loop, and
leaving all other secondary unit
substation loads unaffected.
When a primary feeder conductor fault

occurs, the associated loop feeder
breaker opens and interrupts service
to all loads up to the normally open
primary loop load break switch
(typically half of the loads). Once it is
determined which section of primary
Primary Metal-Clad
Figure 1.1-5. VFI /Selector Switch

Combination
Switchgear Lineup
52
Bus A
Loop Feeder
Loop Feeder
Partial Range
Current-Limiting Fuse
Bay-O-Net
Expulsion Fuse
4-Position
T-Blade
Sectionalizing
Load-Break
Switch
Primary Main Breaker
52
Bus B
52
52
52
Feeder A1
14
cable has been faulted, the loop sectionalizing switches on each side of the
faulted conductor can be opened, the
loop sectionalizing switch that had
been previously left open then closed
and service restored to all secondary
unit substations while the faulted
conductor is replaced. If the fault
should occur in a conductor directly
on the load side of one of the loop
feeder breakers, the loop feeder
breaker is kept open after tripping and
the next load side loop sectionalizing
switch manually opened so that the
faulted conductor can be sectionalized
and replaced.
52
52
Feeder B1
Primary Feeder Breaker
Feeder B2
Feeder A2
To Other
Substations
NO
NC
16
NO
17
18
NC
Typical Secondary Unit

Substation Duplex Primary
Switch/Fuses
Transformer/600V Class
Secondary Switchgear
NO
Figure 1.1-6. Pad-Mounted Transformer

Loop Switching
NC
19
Figure 1.1-7. Basic Primary SelectiveRadial Secondary System
20
21
CA08104001E

System Design
April 2016
1.1-9
Sheet 01 011
Primary
Feeders
52
Loop A
Load Break
Switches
Loop A
In cases where only one primary line

is available, the use of a single primary
breaker provides the loop connections
to the loads as shown here.
Fuses
Figure 1.1-8. Single Primary Feeder

Loop System
A basic primary loop system that
uses a single primary feeder breaker
connected directly to two loop feeder
switches which in turn then feed the
loop is shown in Figure 1.1-8. In this
basic system, the loop may be normally
operated with one of the loop sectionalizing switches open as described
above or with all loop sectionalizing
switches closed. If a fault occurs in the
basic primary loop system, the single
loop feeder breaker trips, and secondary
loads are lost until the faulted conductor
is found and eliminated from the loop
by opening the appropriate loop
sectionalizing switches and then
reclosing the breaker.
3. Primary Selective System

Secondary Radial System
The primary selectivesecondary
radial system, as shown in Figure 1.1-7,
differs from those previously described
in that it employs at least two primary
feeder circuits in each load area. It is
designed so that when one primary
circuit is out of service, the remaining
feeder or feeders have sufficient
capacity to carry the total load. Half
of the transformers are normally
connected to each of the two feeders.
When a fault occurs on one of the
primary feeders, only half of the
load in the building is dropped.
Duplex fused switches as shown in
Figure 1.1-7 and detailed in Figure 1.1-9
may be utilized for this type of system.
Each duplex fused switch consists of
two (2) load break three-pole switches
each in their own separate structure,
connected together by busbars on the
load side. Typically, the load break
switch closest to the transformer
includes a fuse assembly with fuses.
Mechanical and/or key interlocking
is furnished such that both switches
cannot be closed at the same time
(to prevent parallel operation) and
interlocking such that access to
either switch or fuse assembly
cannot be obtained unless both
switches are opened.
CA08104001E
Figure 1.1-9. Duplex Fused Switch in

Two Structures
One alternate to the duplex switch
arrangement, a non-load break selector
switch mechanically interlocked with
a load break fused switch can be used
as shown in Figure 1.1-10. The nonload break selector switch is physically
located in the rear of the load break
fused switch, thus only requiring one
structure and a lower cost and floor
space savings over the duplex
arrangement. The non-load break
switch is mechanically interlocked to
prevent its operation unless the load
break switch is opened. The main
disadvantage of the selector switch is
that conductors from both circuits are
terminated in the same structure.
Primary
Feeders
Non-Load Break
Selector Switches
Interlock
Load Break
Disconnect
Fuses
Figure 1.1-10. Fused Selector Switch in

One Structure
This means limited cable space especially if double lugs are furnished for
each line as shown in Figure 1.1-7 and
should a faulted primary conductor
have to be changed, both lines would
have to be de-energized for safe
changing of the faulted conductors.
A second alternative is utilizing a
three-position selector switch internal
to the transformer, allowing only one
primary feeder to be connected to
the transformer at a time without the
need for any interlocking. The selector
switch is rated for load-breaking.
If overcurrent protection is also
required, a vacuum fault interrupter
(VFI), also internal to the transformer,
may be utilized, reducing floor space.
In Figure 1.1-7 when a primary feeder
fault occurs, the associated feeder
breaker opens and the transformers
normally supplied from the faulted
feeder are out of service. Then manually, each primary switch connected to
the faulted line must be opened and
then the alternate line primary switch
can be closed connecting the transformer to the live feeder, thus restoring
service to all loads. Note that each of the
primary circuit conductors for Feeder
A1 and B1 must be sized to handle the
sum of the loads normally connected
to both A1 and B1. Similar sizing of
Feeders A2 and B2, etc., is required.
If a fault occurs in one transformer,
the associated primary fuses blow
and interrupt the service to just
the load served by that transformer.
Service cannot be restored to the loads
normally served by the faulted
transformer until the transformer
is repaired or replaced.
Cost of the primary selective
secondary radial system is greater
than that of the simple primary radial
system of Figure 1.1-1 because of the
additional primary main breakers, tie
breaker, two-sources, increased number
of feeder breakers, the use of primaryduplex or selector switches, and the
greater amount of primary feeder
cable required. The benefits from the
reduction in the amount of load lost
when a primary feeder is faulted, plus
the quick restoration of service to all
or most of the loads, may more than
offset the greater cost. Having two
sources allows for either manual or
automatic transfer of the two primary
main breakers and tie breaker should
one of the sources become unavailable.
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
1.1-10 Power Distribution Systems

System Design
April 2016
Sheet 01 012
i
ii
1
2
3
4
5
6
7
8
9
The primary selective-secondary radial

system, however, may be less costly or
more costly than a primary loop
secondary radial system of Figure 1.1-3
depending on the physical location
of the transformers while offering
comparable downtime and reliability.
The cost of conductors for the two
types of systems may vary greatly
depending on the location of the
transformers and loads within the
facility and greatly override primary
switching equipment cost differences
between the two systems.
Each transformer secondary is

arranged in a typical double-ended
unit substation arrangement as shown
in Figure 1.1-11. The two secondary
main breakers and secondary tie
breaker of each unit substation are
again either mechanically or electrically
interlocked to prevent parallel operation.
Upon loss of secondary source voltage
on one side, manual or automatic
transfer may be used to transfer the
loads to the other side, thus restoring
power to all secondary loads.
This arrangement permits quick
restoration of service to all loads when
a primary feeder or transformer fault
occurs by opening the associated
secondary main and closing the
secondary tie breaker. If the loss
of secondary voltage has occurred
because of a primary feeder fault with
the associated primary feeder breaker
opening, then all secondary loads
normally served by the faulted feeder
would have to be transferred to the
opposite primary feeder. This means
each primary feeder conductor must be
sized to carry the load on both sides of
all the secondary buses it is serving
under secondary emergency transfer
4. Two-Source Primary
Secondary Selective System
This system uses the same principle
of duplicate sources from the power
supply point using two primary main
breakers and a primary tie breaker.
The two primary main breakers and
primary tie breaker being either
manually or electrically interlocked
to prevent closing all three at the same
time and paralleling the sources. Upon
loss of voltage on one source, a manual
or automatic transfer to the alternate
source line may be used to restore
power to all primary loads.
.
10
52
52
11
Primary Main Breakers
52
52
12
52
52
52
To Other Substations
13
14
Primary Feeder Breakers
To Other Substations
Typical
Double-Ended
Unit
Substation
15
16
17
18
Primary Fused Switch
Transformer
Tie Breaker
Secondary Main Breaker
Figure 1.1-11. Two-Source PrimarySecondary Selective System
19
If the loss of voltage was due to a

failure of one of the transformers in
the double-ended unit substation, then
the associated primary fuses would
open taking only the failed transformer
out of service, and then only the secondary loads normally served by the
faulted transformer would have to be
transferred to the opposite transformer.
In either of the above emergency
conditions, the in-service transformer
of a double-ended unit substation
would have to have the capability of
serving the loads on both sides of the
tie breaker. For this reason, transformers used in this application have equal
kVA rating on each side of the doubleended unit substation and the normal
operating maximum load on each
transformer is typically about 2/3 base
nameplate kVA rating. Typically these
transformers are furnished with
fan-cooling and/or lower than normal
temperature rise such that under
emergency conditions they can carry
on a continuous basis the maximum
load on both sides of the secondary tie
breaker. Because of this spare transformer capacity, the voltage regulation
provided by the double-ended unit
substation system under normal
conditions is better than that of the
systems previously discussed.
The double-ended unit substation
arrangement can be used in conjunction
with any of the previous systems
discussed, which involve two primary
sources. Although not recommended,
if allowed by the utility, momentary
re-transfer of loads to the restored
source may be made closed transition
(anti-parallel interlock schemes would
have to be defeated) for either the
primary or secondary systems. Under
this condition, all equipment interrupting and momentary ratings should be
suitable for the fault current available
from both sources.
For double-ended unit substations
equipped with ground fault systems
special consideration to transformer
neutral grounding and equipment
operation should be madesee
Grounding and Ground Fault
Protection in Section 1.4. Where
two single-ended unit substations are
connected together by external tie
conductors, it is recommended that
a tie breaker be furnished at each end
of the tie conductors.
20
21
CA08104001E

System Design
April 2016
1.1-11
Sheet 01 013
5. Sparing Transformer System

The sparing transformer system concept
came into use as an alternative to the
capital cost intensive double-ended
secondary unit substation distribution
system (see Two-Source Primary
Secondary Selective System). It essentially replaces double-ended substations
with single-ended substations and one
or more sparing transformer substations all interconnected on a common
secondary bus (see Figure 1.1-12).
Generally no more than three to five
single-ended substations are on a
sparing loop.
The essence of this design philosophy
is that conservatively designed and
loaded transformers are highly reliable
electrical devices and rarely fail. Therefore, this design provides a single common backup transformer for a group of
transformers in lieu of a backup transformer for each and every transformer.
This system design still maintains a
high degree of continuity of service.
Referring to Figure 1.1-12, it is apparent

that the sparing concept backs up
primary switch and primary cable
failure as well. Restoration of lost or
failed utility power is accomplished
similarly to primary selective scheme
previously discussed. It is therefore
important to use an automatic throwover system in a two source lineup
of primary switchgear to restore utility
power as discussed in the Two-Source
Primary schemesee Figure 1.1-11.
A major advantage of the sparing
transformer system is the typically
lower total base kVA of transformation.
In a double-ended substation design,
each transformer must be rated to
carry the sum of the loads of two busses
and usually requires the addition of
cooling fans to accomplish this rating.
In the sparing concept, each transformer carries only its own load, which
is typically not a fan-cooled rating. Major
space savings is also a benefit of this
system in addition to first cost savings.
Sparing Transformer
K
Typical Single-Ended Substation
All main breakers, including

the sparing main breaker, are
normally closed; the tie breakers
are normally open
Once a transformer (or primary
cable or primary switch/fuse) fails,
the associated secondary main
breaker is opened. The associated
tie breaker is then closed, which
restores power to the single-ended
substation bus
Schemes that require the main to
be opened before the tie is closed
(open transition), and that allow
any tie to be closed before the
substation main is opened,
(closed transition) are possible
With a closed transition scheme, it is
common to add a timer function that
opens the tie breaker unless either
main breaker is opened within a
time interval.
This closed transition allows power
to be transferred to the sparing
transformer without interruption, such
as for routine maintenance, and then
back to the substation. This closed
transition transfer has an advantage in
some facilities; however, appropriate
interrupting capacities and bus bracing
must be specified suitable for the
momentary parallel operation.
In facilities without qualified electrical
power operators, an open transition
with key interlocking is often a
prudent design.
Careful sizing of these transformers

as well as careful specification of the
transformers is required for reliability.
Low temperature rise specified with
continuous overload capacity or
upgraded types of transformers
should be considered.
One disadvantage to this system is
the external secondary tie system,
see Figure 1.1-12. As shown, all singleended substations are tied together
on the secondary with a tie busway or
cable system. Location of substations
is therefore limited because of voltage
drop and cost considerations.
Figure 1.1-12. Sparing Transformer System
Note: Each pair of main breaker/tie breaker

key cylinders should be uniquely keyed to
prevent any paralleled source operations.
Typical Secondary Busway Loop
The sparing transformer system

operates as follows:
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

System Design
April 2016
Sheet 01 014
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Routing of busway, if used, must be

carefully layed out. It should also be
noted, that a tie busway or cable fault
will essentially prevent the use of the
sparing transformer until it is repaired.
Commonly, the single-ended substations and the sparing transformer
must be clustered. This can also be
an advantage, as more kVA can be
supported from a more compact
space layout.
6. Simple Spot Network Systems

The AC secondary network system
is the system that has been used for
many years to distribute electric power
in the high-density, downtown areas
of cities, usually in the form of utility
grids. Modifications of this type of
system make it applicable to serve
loads within buildings.
The major advantage of the secondary
network system is continuity of
service. No single fault anywhere
on the primary system will interrupt
service to any of the systems loads.
Most faults will be cleared without
interrupting service to any load.
Another outstanding advantage that
the network system offers is its flexibility to meet changing and growing load
conditions at minimum cost and
minimum interruption in service to
other loads on the network. In addition
to flexibility and service reliability, the
secondary network system provides
exceptionally uniform and good
voltage regulation, and its high
efficiency materially reduces the
costs of system losses.
Three major differences between the
network system and the simple radial
system account for the outstanding
advantages of the network. First,
a network protector is connected in
the secondary leads of each network
transformer in place of, or in addition
to, the secondary main breaker, as
shown in Figure 1.1-13. Also, the
secondaries of each transformer in
a given location (spot) are connected
together by a switchgear or ring bus
from which the loads are served over
short radial feeder circuits. Finally, the
primary supply has sufficient capacity
to carry the entire building load without overloading when any one primary
feeder is out of service.
A network protector is a specially
designed heavy-duty air power breaker,
spring close with electrical motor-charged
mechanism, with a network relay to
control the status of the protector
(tripped or closed).
The network relay is usually a solidstate microprocessor-based component integrated into the protector
enclosure that functions to automatically close the protector only when the
voltage conditions are such that its
associated transformer will supply
power to the secondary network loads,
and to automatically open the protector when power flows from the secondary to the network transformer.
The purpose of the network protector
is to protect the integrity of the network bus voltage and the loads served
from it against transformer and primary feeder faults by quickly disconnecting the defective feedertransformer pair from the
network when backfeed occurs.
The optimum size and number of

primary feeders can be used in the
spot network system because the
loss of any primary feeder and its
associated transformers does not
result in the loss of any load even
for an instant. In spite of the spare
capacity usually supplied in network
systems, savings in primary switchgear and secondary switchgear costs
often result when compared to a radial
system design with similar spare
capacity. This occurs in many radial
systems because more and smaller
feeders are often used in order to
minimize the extent of any outage
when a primary fault event occurs.
In spot networks, when a fault occurs
on a primary feeder or in a transformer,
the fault is isolated from the system
through the automatic tripping of the
primary feeder circuit breaker and all
of the network protectors associated
with that feeder circuit. This operation
does not interrupt service to any loads.
After the necessary repairs have been
made, the system can be restored to
normal operating conditions by closing
the primary feeder breaker. All network
protectors associated with that feeder
will close automatically.
The simple spot network system

resembles the secondary-selective
radial system in that each load area
is supplied over two or more primary
feeders through two or more transformers. In network systems, the
transformers are connected through
network protectors to a common
bus, as shown in Figure 1.1-13, from
which loads are served. Because the
transformers are connected in parallel,
a primary feeder or transformer fault
does not cause any service interruption to the loads. The paralleled
transformers supplying each load
bus will normally carry equal load
currents, whereas equal loading of
the two separate transformers supplying a substation in the secondaryselective radial system is difficult to
obtain. The interrupting duty imposed
on the outgoing feeder breakers in the
network will be greater with the spot
network system.
The chief purpose of the network bus

normally closed ties is to provide for
the sharing of loads and a balancing
of load currents for each primary
service and transformer regardless of
the condition of the primary services.
Also, the ties provide a means for
isolating and sectionalizing ground
fault events within the switchgear
network bus, thereby saving a portion
of the loads from service interruptions,
yet isolating the faulted portion for
corrective action.
Typical Feeder
Primary Circuit
To Other
Networks
Network Transformer
Network Protector
Fuses
Optional Main, 50/51
Relaying and/or
Network Disconnect
Tie
Tie
NC
LV Feeder
Customer
Loads
Drawout
Low Voltage
Switchgear
NC
Customer
Loads
Customer
Loads
Figure 1.1-13. Three-Source Spot Network
CA08104001E
April 2016

System Design
1.1-13
Sheet 01 015
The use of spot network systems

provides users with several important
advantages. First, they save transformer capacity. Spot networks permit
equal loading of transformers under
all conditions. Also, networks yield
lower system losses and greatly
improve voltage conditions. The
voltage regulation on a network
system is such that both lights and
power can be fed from the same
load bus. Much larger motors can
be started across-the-line than on a
simple radial system. This can result in
simplified motor control and permits
the use of relatively large low voltage
motors with their less expensive
control. Finally, network systems
provide a greater degree of flexibility
in adding future loads; they can be
connected to the closest spot
network bus.
Spot network systems are economical
for buildings that have heavy concentrations of loads covering small areas,
with considerable distance between
areas, and light loads within the
distances separating the concentrated
loads. They are commonly used in
hospitals, high rise office buildings,
and institutional buildings where a
high degree of service reliability is
required from the utility sources.
Spot network systems are especially
economical where three or more
primary feeders are available.
Principally, this is due to supplying
each load bus through three or
more transformers and the reduction
in spare cable and transformer
capacity required.
They are also economical when
compared to two transformer doubleended substations with normally
opened tie breakers.
Emergency power should be connected
to network loads downstream from
the network, or upstream at primary
voltage, not at the network bus itself.
7. Medium Voltage Distribution

System Design
i
Utility #2
Utility #1
A. Single Bus, Figure 1.1-14

The sources (utility and/or generator(s))
are connected to a single bus. All feeders
are connected to the same bus.
Standby
Normal
ii
1
Utility
2
G
52 NO
52 NC
3
Loads
52
52
Main Bus
52
One of Several Feeders
Figure 1.1-14. Single Bus

This configuration is the simplest
system; however, outage of the utility
results in total outage.
Normally the generator does not have
adequate capacity for the entire load.
A properly relayed system equipped
with load shedding, automatic voltage/
frequency control may be able to
maintain partial system operation.
Any future addition of breaker sections
to the bus will require a shutdown of
the bus, because there is no tie breaker.
B. Single Bus with Two Sources from the

Utility, Figure 1.1-15
Same as the single bus, except that
two utility sources are available.
This system is operated normally with
the main breaker to one source open.
Upon loss of the normal service, the
transfer to the standby normally
open (NO) breaker can be automatic
or manual. Automatic transfer is
preferred for rapid service restoration
especially in unattended stations.
Figure 1.1-15. Single Bus with Two-Sources

Retransfer to the Normal can be
closed transition subject to the approval
of the utility. Closed transition momentarily (510 cycles) parallels both
utility sources. Caution: when both
sources are paralleled, the fault current
available on the load side of the main
device is the sum of the available fault
current from each source plus the motor
fault contribution. It is recommended
that the short-circuit ratings of the
bus, feeder breakers and all load side
equipment are rated for the increased
available fault current. If the utility
requires open transfer, the disconnection of motors from the bus must be
ensured by means of suitable time delay
on reclosing as well as supervision
of the bus voltage and its phase with
respect to the incoming source voltage
This busing scheme does not preclude
the use of cogeneration, but requires
the use of sophisticated automatic synchronizing and synchronism checking
controls, in addition to the previously
mentioned load shedding, automatic
frequency and voltage controls.
This configuration is more expensive
than the scheme shown in Figure 1.1-14,
but service restoration is quicker. Again,
a utility outage results in total outage to
the load until transfer occurs. Extension
of the bus or adding breakers requires
a shutdown of the bus.
If paralleling sources, reverse current,
reverse power and other appropriate
relaying protection should be added
as requested by the utility.
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

System Design
April 2016
Sheet 01 016
i
ii
1
2
3
C. Multiple Sources with Tie Breaker,

Figure 1.1-16 and Figure 1.1-17
This configuration is similar to configuration B. It differs significantly in that
both utility sources normally carry the
loads and also by the incorporation
of a normally open tie breaker. The
outage to the system load for a utility
outage is limited to half of the system.
Again, the closing of the tie breaker can
be manual or automatic. The statements
made for the retransfer of scheme B
apply to this scheme also.
Utility #1
Utility #2
4
5
6
52 NC
52 NC
NO
7
8
Bus #1
52
Bus #2
52
52
Load
Load
9
Figure 1.1-16. Two-Source Utility with
Tie Breaker
11
If looped or primary selective distribution system for the loads is used, the
buses can be extended without a shutdown by closing the tie breaker and
transferring the loads to the other bus.
13
14
15
Summary
The third tie breaker allows any bus

to be fed from any utility source.
In the design of a modern medium

voltage system, the engineer should:
This configuration is more expensive

than B. The system is not limited to two
buses only. Another advantage is that
the design may incorporate momentary
paralleling of buses on retransfer after
the failed line has been restored to prevent another outage. See the Caution for
Figures 1.1-15, 1.1-16 and 1.1-17.
The medium voltage system configurations shown are based on using metalclad drawout switchgear. The service
continuity required from electrical
systems makes the use of single-source
systems impractical.
1. Design a system as simple as

possible.
Caution for Figures 1.1-15, 1.1-16 and

1.1-17: If continuous paralleling of
sources is planned, reverse current,
reverse power and other appropriate
relaying protection should be added.
When both sources are paralleled for
any amount of time, the fault current
available on the load side of the main
device is the sum of the available
fault current from each source plus
the motor fault contribution. It is
required that bus bracing, feeder
breakers and all load side equipment
is rated for the increased available
fault current.
52 NC
Bus #1
2. Limit an outage to as small a

portion of the system as possible.
3. Provide means for expanding the
system without major shutdowns.
4. Relay the system so that only the
faulted part is removed from
service, and damage to it is minimized consistent with selectivity.
5. Specify and apply all equipment
within its published ratings and
national standards pertaining to
the equipment and its installation.
Utility #2
Utility #1
10
12
In Figure 1.1-17, closing of the tie

breaker following the opening of a
main breaker can be manual or automatic. However, because a bus can
be fed through two tie breakers, the
control scheme should be designed
to make the selection.
Utility #3
52 NC
52 NC
NO
52
52 NO 52 Typical Feeder
Bus #2
52
NO
Bus #3
52
52
52 NO
Tie Busway
Figure 1.1-17. Triple-Ended Arrangement
16
17
18
19
20
21
CA08104001E

System Design
April 2016
1.1-15
Sheet 01 017
Health Care Facilities
NFPA 101-2009Life Safety Code

NFPA 110-2010Standard for Emergency and Standby Power Systems
NFPA 111-2010Standard on Stored
Electrical Energy Emergency and
Standby Power Systems
Health care facilities are defined by

NFPA (National Fire Protection Agency)
as Buildings or portions of buildings
in which medical, dental, psychiatric,
nursing, obstetrical, or surgical care
are provided. Due to the critical nature
of the care being provided at these
facilities and their increasing dependence on electrical equipment for preservation of life, health care facilities
have special requirements for the
design of their electrical distribution
systems. These requirements are
typically much more stringent than
commercial or industrial facilities.
The following section summarizes
some of the unique requirements
of health care facility design.
These NFPA guidelines represent the

most industry recognized standard
requirements for health care electrical
design. However, the electrical design
engineer should consult with the
authorities having jurisdiction over
the local region for specific electrical
distribution requirements.
The electrical system requirements for

the essential electrical system (EES)
vary according to the type of health
care facility. Health care facilities are
categorized by NFPA 99 as Type 1,
Type 2 or Type 3 facilities. Some
example health care facilities, classified
by type, are summarized in the
following Table 1.1-8.
ii
Table 1.1-8. Health Care Facilities
Description
Ambulatory
surgical
facilities
Other health
care facilities
Health care electrical systems usually

consist of two parts:
1. Non-essential or normal
electrical system.
2. Essential electrical system.
All electrical power in a health care
facility is important, though some
loads are not critical to the safe operation of the facility. These non-essential
or normal loads include things such
as general lighting, general lab equipment, non-critical service equipment,
patient care areas, etc. These loads are
not required to be fed from an alternate
source of power.
NFPA 37-2010Standard for

Stationary Combustion Engines
and Gas Turbines
NFPA 70-2011National
Electrical Code
NFPA 99-2005Health Care Facilities
EES Type
Hospitals
NFPA 99 Chap. 13 Type 1
Nursing homes NFPA 99 Chap. 17 Type 2
Limited care
facilities
NFPA 99 Chap. 18 Type 2
Health Care Electrical System

Requirements
There are several agencies and organizations that develop requirements

for health care electrical distribution
system design. The following is a
listing of some of the specific NFPA
(National Fire Protection Agency)
standards that affect health care
facility design and implementation:
Definition
NFPA 99 Chap. 14 Type 3 1

NFPA 99 Chap. 14 Type 3 1
If electrical life support or critical care areas

are present, then facility is classified as Type 1.
Type 1 Essential Electrical

Systems (EES)
Type 1 essential electrical systems
(EES) have the most stringent requirements for providing continuity of
electrical service and will, therefore,
be the focus of this section. Type 1
EES requirements meet or exceed
the requirements for Type 2 and
Type 3 facilities.
3
4
5
6
7
8
9
10
11
Normal Source
Normal Source
Normal Source
Emergency Power Supply

G
12
13
14
15
16
Non-Essential Loads
Non-Essential Loads
17
18
Manual Transfer Switch

Delayed Automatic Transfer Switch
Equipment
System
Life Safety Critical

Branch
Branch
Emergency System
Automatic (Non-Delaying)
Transfer Switch
Essential Electrical System
Figure 1.1-18. Typical Large Hospital Electrical SystemType 1 Facility
CA08104001E
19
20
21

System Design
April 2016
Sheet 01 018
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
Sources: Type 1 systems are required

to have a minimum of two independent
sources of electrical powera normal
source that generally supplies the
entire facility and one or more alternate sources that supply power when
the normal source is interrupted. The
alternate source(s) must be an on-site
generator driven by a prime mover
unless a generator(s) exists as the
normal power source. In the case
where a generator(s) is used as the
normal source, it is permissible for the
alternate source to be a utility feed.
Alternate source generators must be
classified as Type 10, Class X, Level 1
gensets per NFPA 110 Tables 4.1(a) and
4.2(b) that are capable of providing
power to the load in a maximum of
10 seconds. Typically, the alternate
sources of power are supplied to the
loads through a series of automatic
and/or manual transfer switches (see
Tab 25). The transfer switches can
be non-delayed automatic, delayed
automatic or manual transfer depending
on the requirements of the specific
branch of the EES that they are feeding.
It is permissible to feed multiple
branches or systems of the EES from
a single automatic transfer switch
provided that the maximum demand
on the EES does not exceed 150 kVA.
This configuration is typically seen
in smaller health care facilities that
must meet Type 1 EES requirements
(see Figure 1.1-19).
Normal Source
Alternate
Source
13
14
15
16
17
18
19
Non-Essential
Loads
Entire Essential
Electric System
(150 kVA or Less)
Figure 1.1-19. Small Hospital Electrical

SystemSingle EES Transfer Switch
Table 1.1-9. Type 1 EES Applicable Codes

Description
Standard
Section
Design
Sources
NFPA 99
NFPA 99
Uses
Emergency
Power Supply
Classification
NFPA 99
4.4.1.1.1
4.4.1.1.4 thru
4.4.4.1.1.7.2
4.4.1.1.8 (1-3)
NFPA 110
Distribution
NFPA 99
NEC
4.4.2
517.30
Systems and Branches of Service: The

Type 1 EES consists of two separate
power systems capable of supplying
power considered essential for life
safety and effective facility operation
during an interruption of the normal
power source. They are the emergency
system and the equipment system.
1. Emergency systemconsists of
circuits essential to life safety and
critical patient care.
The emergency system is an electrical
sub-system that must be fed from an
automatic transfer switch or series of
automatic transfer switches. This
emergency system consists of two
mandatory branches that provide power
to systems and functions essential to
life safety and critical patient care.
A. Life safety branchsupplies
power for lighting, receptacles
and equipment to perform the
following functions:
1.
2.
3.
4.
Illumination of means of egress.

Exit signs and exit direction signs.
Alarms and alerting systems.
Emergency communications
systems.
5. Task illumination, battery
chargers for battery powered
lighting, and select receptacles
at the generator.
6. Elevator lighting control, communication and signal systems.
7. Automatic doors used for egress.
These are the only functions
permitted to be on the life safety
branch. Life safety branch equipment and wiring must be entirely
independent of all other loads
and branches of service. This
includes separation of raceways,
boxes or cabinets. Power must be
supplied to the life safety branch
from a non-delayed automatic
transfer switch.
B. Critical branchsupplies power

for task illumination, fixed equipment, selected receptacles and
selected power circuits for areas
related to patient care. The
purpose of the critical branch
is to provide power to a limited
number of receptacles and locations to reduce load and minimize
the chances of fault conditions.
The transfer switch(es) feeding the
critical branch must be automatic
type. They are permitted to have
appropriate time delays that will
follow the restoration of the life
safety branch, but should have
power restored within 10 seconds
of normal source power loss.
The critical branch provides power
to circuits serving the following
areas and functions:
1. Critical care areas.
2. Isolated power systems in
special environments.
3. Task illumination and selected
receptacles in the following
patient care areas: infant
nurseries, medication prep
areas, pharmacy, selected
acute nursing areas, psychiatric
bed areas, ward treatment
rooms, nurses stations.
4. Specialized patient care task
illumination, where needed.
5. Nurse call systems.
6. Blood, bone and tissue banks.
7. Telephone equipment rooms
and closets.
8. Task illumination, selected
receptacles and selected power
circuits for the following: general
care beds (at least one duplex
receptacle), angiographic labs,
cardiac catheterization labs,
coronary care units, hemodialysis
rooms, selected emergency
room treatment areas, human
physiology labs, intensive care
units, selected postoperative
recovery rooms.
9. Additional circuits and singlephase fraction motors as needed
for effective facility operation.
20
21
CA08104001E

System Design
April 2016
1.1-17
Sheet 01 019
Table 1.1-10. Type 1Emergency System

Applicable Codes
Description
Standard
Section
General
NFPA 99
NEC
4.4.2.2.2
517.31
Life safety
branch
NFPA 99
NEC
4.4.2.2.2.2
517.32
Critical branch
NFPA 99
NEC
4.4.2.2.2.3
517.33
Wiring
NFPA 99
NEC
4.4.2.2.4
517.30(C)
The following equipment must be

arranged for delayed automatic or
manual transfer to the emergency
power supply:
1. Select heating equipment.
2. Select elevators.
3. Supply, return and exhaust
ventilating systems for surgical,
obstetrical, intensive care,
coronary care, nurseries and
emergency treatment areas.
4. Supply, return and exhaust
ventilating systems for airborne
infectious/isolation rooms, labs and
medical areas where hazardous
materials are used.
5. Hyperbaric facilities.
6. Hypobaric facilities.
7. Autoclaving equipment.
8. Controls for equipment listed above.
9. Other selected equipment in
kitchens, laundries, radiology
rooms and central refrigeration
as selected.
2. Equipment systemconsists of
major electrical equipment necessary
for patient care and Type 1 operation.
The equipment system is a subsystem
of the EES that consists of large electrical
equipment loads needed for patient
care and basic hospital operation.
Loads on the equipment system that
are essential to generator operation are
required to be fed by a non-delayed
automatic transfer switch.
The following equipment must be
arranged for delayed automatic transfer
to the emergency power supply:
1. Central suction systems for medical
and surgical functions.
2. Sump pumps and other equipment
required for the safe operation of
a major apparatus.
3. Compressed air systems for
medical and surgical functions.
4. Smoke control and stair
pressurization systems.
5. Kitchen hood supply and exhaust
systems, if required to operate
during a fire.
Table 1.1-11. Type 1Equipment System

Applicable Codes
Description
Standard
Section
General
NFPA 99
NEC
4.4.2.2.3
517.34
Equipment
NFPA 99
NEC
4.4.2.2.3 (3-5)
517.34(A)-(B)
Any loads served by the generator that

are not approved as outlined above as
part of the essential electrical system
must be connected through a separate
transfer switch. These transfer switches
must be configured such that the loads
will not cause the generator to overload
Normal Source
and must be shed in the event the

generator enters an overload condition.
Ground fault protectionper NFPA 70
NEC Article 230.95, ground fault
protection is required on any feeder or
service disconnect 1000 A or larger on
systems with line to ground voltages
of 150 V or greater and phase-to-phase
voltages of 600 V or less. For health care
facilities (of any type), a second level of
ground fault protection is required to
be on the next level of feeder downstream. This second level of ground
fault is only required for feeders that
serve patient care areas and equipment
intended to support life. 100% selective
coordination of the two levels of ground
fault protection must be achieved with a
minimum six-cycle separation between
the upstream and downstream device.
New in the 2011 NEC, ground fault
protection is now allowed between
the generator(s) and the EES transfer
switch(es). However, NEC 517.17(B) prohibits the installation of ground fault
protection on the load side of a transfer
switch feeding EES circuits (see Figure
1.1-20additional level of ground fault).
Careful consideration should be used in
applying ground fault protection on the
essential electrical system to prevent
a ground fault that causes a trip of the
normal source to also cause a trip on
the emergency source. Such an event
could result in complete power loss of
both normal and emergency power
sources and could not be recovered
until the source of the ground fault
was located and isolated from the
system. To prevent this condition,
NEC 700.26 removes the ground fault
protection requirement for the
Normal Source(s)
480/277V 1
1000 A
Service
GF
or Larger
Entrance
GF GF GF GF GF
480/277 V 1
1000 A
Service
GF
or Larger
Entrance
1000 A
Service
GF
or Larger
Entrance
Additional Level
of Ground Fault
Protection
Non-Essential Loads
GF GF GF
GF GF GF
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
G
480/277V
Generator Breakers are

Typically Supplied with
Ground Fault Alarm
Only. (NEC 700.26)
Ground Fault
is Permitted
Between Generator
and EES Transfer
Switches.
(NEC 517.17(B))
15
16
17
18
Non-Essential Loads
19
GF = Ground Fault Protection Required
Essential Electrical System
Additional Level of Ground Fault is

not Permitted on Load Side of EES
Transfer Switches. (NEC 517.17a(2))
Figure 1.1-20. Additional Level of Ground Fault Protection

1
Ground fault protection is required for service disconnects 1000 A and larger or systems with less than 600 V phase-to-phase and greater than 150 V to
ground per NEC 230.95.
CA08104001E
20
21

System Design
April 2016
Sheet 01 020
ii
emergency system source. Typically,

the emergency system generator(s)
are equipped with ground fault alarms
that do not automatically disconnect
power during a ground fault.
Table 1.1-12. Ground Fault Protection

Applicable Codes
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Description
Standard
Section
Services
Feeders
NEC
NEC
230.95
215.10
Additional level
NEC
NFPA 99
517.17
4.3.2.5
Alternate source
NEC
NEC
700.26
701.26
Wet procedure locationsA wet

procedure location in a health care
facility is any patient care area that
is normally subject to wet conditions
while patients are present. Typical wet
procedure locations can include operating rooms, anesthetizing locations,
dialysis locations, etc. (Patient beds,
toilets and sinks are not considered
wet locations.) These wet procedure
locations require special protection
to guard against electric shock. The
ground fault current in these areas
must be limited to not exceed 6 mA.
In areas where the interruption of power
is permissible, ground fault circuit
interrupters (GFCI) can be employed.
GFCIs will interrupt a circuit when
ground fault current exceeds 5 mA
(1 mA).
In areas where the interruption of
power cannot be tolerated, protection
from ground fault currents is accomplished through the use of an isolated
power system. Isolated power systems
provide power to an area that is isolated from ground (or ungrounded).
This type of system limits the amount
of current that flows to ground in
the event of a single line-to-ground
fault and maintains circuit continuity.
Electronic line isolation monitors (LIM)
are used to monitor and display leakage
currents to ground. When leakage
current thresholds are exceeded, visible
and/or audible alarms are initiated to
alert occupants of a possible hazardous
condition. This alarm occurs without
interrupting power to allow for the
safe conclusion of critical procedures.
Table 1.1-13. Wet Procedure Location
Applicable Codes
Description
Standard
Section
General
NFPA 99
NEC
4.3.2.2.9
517.20
Isolated power
systems
NFPA 99
NEC
4.3.2.6
517.160
Maintenance and Testing

Regular maintenance and testing of
the electrical distribution system in
a health care facility is necessary to
ensure proper operation in an emergency and, in some cases, to maintain
government accreditation. Any health
care facility receiving Medicare or
Medicaid reimbursement from the
government must be accredited by
the Joint Commission on Accreditation
of Health Care Organizations (JCAHO).
JCAHO has established a group of
standards called the Environment of
Care, which must be met for health
care facility accreditation. Included in
these standards is the regular testing
of the emergency (alternate) power
system(s). Diesel-powered EPS installations must be tested monthly in
accordance with NFPA 110 Standard
for Emergency and Standby Power
Systems. Generators must be tested
for a minimum of 30 minutes under
the criteria defined in NFPA 110.
One method to automate the task of
monthly generator tests is through the
use of Power Xpert communications.
With the Power Xpert integrated metering, monitoring and control system, a
facility maintenance director can initiate
a generator test, control/monitor
loads, meter/monitor generator test
points and create a JCAHO compliant
report automatically from a central PC.
The report contains all metered values,
test results, date/time information, etc.
necessary to satisfy JCAHO requirements. This automated generator testing
procedure reduces the labor, training
and inaccuracies that occur during
manual emergency power system tests.
(See Power Monitoring Tab 2.)
Table 1.1-14. Maintenance and Testing
Applicable Codes
Description
Standard
Section
Grounding
NFPA 99
4.3.3.1
Emergency power
system
NFPA 99
JCAHO
4.4.4.1.1
EC.2.14(d)
Generator
NFPA 110
8.4
Transfer switches
NFPA 110
8.3.5, 8.4.6
Breakers
NFPA 99
NFPA 110
4.4.4.1.2
8.4.7
Routine maintenance should be

performed on circuit breakers, transfer
switches, switchgear, generator equipment, etc. by trained professionals
to ensure the most reliable electrical
system possible. See Tab 41 for Eatons
Electrical Services & Systems (EESS),
which provides engineers,
21
trained in development and execution

of annual preventative maintenance
procedures of health care facility
electrical distribution systems.
Paralleling Emergency Generators

Without Utility Paralleling
In many health care facilities (and
other large facilities with critical
loads), the demand for standby
emergency power is large enough
to require multiple generator sets to
power all of the required essential
electrical system (EES) loads. In many
cases, it becomes more flexible and
easier to operate the required multiple
generators from a single location using
generator paralleling switchgear.
Figure 1.1-21 on Page 1.1-19 shows
an example of a typical one-line for a
paralleling switchgear lineup feeding
the EES.
A typical abbreviated sequence of
operation for a multiple emergency
generator and ATS system follows.
Note that other modes of operation
such as generator demand priority and
automated testing modes are available
but are not included below. (Reference
Tab 41 for complete detailed
sequences of operation.)
1. Entering emergency mode
a. Upon loss of normal source,
automatic transfer switches
send generator control system
a run request.
b. All available generators are
started. The first generator up
to voltage and frequency is
closed to the bus.
c. Unsheddable loads and load
shed Priority 1 loads are powered in less than 10 seconds.
d. The remaining generators are
synchronized and paralleled
to the bus as they come up to
voltage and frequency.
e. As additional generators are
paralleled to the emergency
bus, load shed priority levels
are added, powering their
associated loads.
f. The system is now in
emergency mode.
2. Exit from emergency mode
a. Automatic transfer switches
sense the utility source is
within acceptable operational
tolerances for a time duration
set at the automatic transfer
switch.
CA08104001E

System Design
April 2016
1.1-19
Sheet 01 021
With Utility Paralleling
b. As each automatic transfer

switch transfers back to utility
power, it removes its run
request from the generator
plant.
c. When the last automatic transfer switch has retransferred to
the utility and all run requests
have been removed from the
generator plant, all generator
circuit breakers are opened.
d. The generators are allowed
to run for their programmed
cool-down period.
e. The system is now back in
automatic/standby mode.
Today, many utilities are offering their

customers excellent financial incentives to use their on-site generation
capacity to remove load from the utility
grid. These incentives are sometimes
referred to as limited interruptible
rates (LIP). Under these incentives,
utilities will greatly reduce or eliminate
kWhr or kW demand charges to their
customers with on-site generation
capabilities. In exchange, during times
of peak loading of the utility grid, the
utility can ask their LIP rate customers
to drop load from the grid by using
their on-site generation capabilities.
Many health care facilities are taking

advantage of these utility incentives
by adding generator capacity over
and above the NFPA requirements.
Figure 1.1-22 on Page 1.1-20 shows
an example one-line of a health care
facility with complete generator
backup and utility interconnect.
ii
NFPA 110 requirements state that the

normal and emergency sources must
be separated by a fire-rated wall.
The intent of this requirement is so that

a fire in one location cannot take out
both sources of power. To meet this
requirement, the paralleling switchgear
must be split into separate sections
with a tie bus through a fire-rated wall.
For more information on generator
paralleling switchgear, see Tab 40.
Health care facilities are ideally suited

to take advantage of these programs
because they already have significant
on-site generation capabilities due to
the code requirements described.
3
4
5
6
Utility
Transformer
Generators X = Number of Units

G1
Utility
Metering
G2
Gx
Typical
Generator
Breaker
10
Service Main
Emergency Bus
Normal Bus
Optional
Electrically
Operated
Stored
Energy
Breakers
Optional Electrically
Operated Stored
Energy Breakers
F1
F2
EF1
Fx
EF2
11
12
EFx
13
14
Equipment
ATS # 1
Non-Essential
Loads
EP1
Life Safety
ATS # 2
EP2
Typical
Panelboards
Critical
ATS # X
EPX
Load Shed/Load
Add ATS Units
Optional Closed
Transition
Paralleling of
Generators and
Utility
15
16
17
Figure 1.1-21. Typical One-Line for a Paralleling Switchgear Lineup Feeding the Essential Electrical System (EES)
18
19
20
21
CA08104001E

System Design
April 2016
Sheet 01 022
i
ii
Transformer
Generators X = Number of Units

Utility
Metering
1
2
Fire-Rated Wall
or Separation Barrier
Utility
G1
Utility
Protective
Relay
Closed
Transition
Paralleling of
Generators and
Utility, Plus
Soft Loading/
Unloading
Service Main
G2
Gx
Typical
Generator
Breaker
Normal Bus
Emergency Bus
4
5
6
TIE
Optional
Electrically
Operated
Stored
Energy
Breakers
F1
7
8
9
10
F2
Fx
Optional TIE
Field Installed
Cable or Busway
Equipment
ATS # 1
Non-Essential
Loads
EP1
Electrically Operated
Stored Energy
Breakers
EF1
EF2
EFx
Life Safety
ATS # 2
EP2
Critical
ATS # X
EPX
Load Shed/
Load Add
ATS Units
Typical
Panelboards
Figure 1.1-22. Typical One-Line Health Care Facility with Complete Generator Backup and Utility Interconnect
11
12
13
14
15
16
17
18
19
20
21
CA08104001E
April 2016

1.2-1
Sheet 01 023
Generators and
Generator Systems
Typical Diesel GensetCaterpillar
Introduction
The selection and application
of generators into the electrical
distribution system will depend on
the particular application. There are
many factors to consider, including
code requirements, environmental
constraints, fuel sources, control
complexity, utility requirements and
load requirements. The health care
requirements for legally required
emergency standby generation
systems are described starting on
Page 1.1-15. Systems described in
this section are applicable to health
care requirements, as well as other
facilities that may require a high
degree of reliability. The electrical
supply for data centers, financial
institutions, telecommunications,
government and public utilities
also require high reliability. Threats
of disaster or terror attacks have
prompted many facilities to require
complete self-sufficiency for
continuous operation.
2011 NEC Changes Related to

Generator Systems
Article 250.30Grounding Separately
Derived AC Systemshas been
completely rewritten for clarity and
for usability. Most notably, the term
equipment bonding jumper was
changed to supply-side bonding
jumper (see 250.30(A)(2)). This was
necessary to ensure proper identification and installation of bonding
conductors within or on the supply
side of service equipment and
between the source of a separately
derived system and the first disconnecting means. The other requirements for grounded systems were
renumbered to accommodate the
250.30(A)(2) change. 250.30(B)(3)
Ungrounded Systemshas been
added, and this language requires
a supply-side bonding jumper to

be installed from the source of a
separately derived system to the first
disconnecting means in accordance
with 250.30(A)(2). Another new
requirement, 250.30(C)Outdoor
Sourcehas been added, and requires
a grounding electrode connection at
the source location when the separately
derived system is located outside
of the building or the structure
being supplied.
Article 445.19Generators Supplying
Multiple Loadshas been revised
to require that the generator have
overcurrent protection per 240.15(A)
when using individual enclosures
tapped from a single feeder.
Article 517.17(B)Feeder GFP (Health
Care Facilities)now allows, but does
not require, multiple levels of GFPE
upstream of the transfer switch when
the choice is made to provide GFPE
on the alternate power source
(i.e., generator).
Article 701.6(D)Signals (Legally
Required Standby Systems)now
requires ground fault indication for
legally required standby systems of
more than 150 V to ground and OCPDs
rated 1000 A or more.
Types of Engines
Many generator sets are relatively
small in size, typically ranging from
several kilowatts to several megawatts.
These units are often required to come
online and operate quickly. They need
to have the capacity to run for an
extended period of time. The internal
combustion engine is an excellent
choice as the prime mover for the
majority of these applications. Turbines
may also be used. Diesel-fueled
engines are the most common, but
other fuels used include natural gas,
digester gas, landfill gas, propane,
biodiesel, crude oil, steam and others.
Some campuses and industrial
facilities use and produce steam
for heating and other processes.
These facilities may find it economically
feasible to produce electricity as a
byproduct of the steam production.
These installations would typically
be classified as a cogeneration facility
producing a fairly constant power
output and operating in parallel with
the electric utility system.
Types of Generators
Generators can be either synchronous
or asynchronous. Asynchronous
generators are also referred to as
induction generators. The construction
is essentially the same as an induction
motor. It has a squirrel-cage rotor and
wound stator. An induction generator
is a motor driven above its designed
synchronous speed thus generating
power. It will operate as a motor if it
is running below synchronous speed.
The induction generator does not have
an exciter and must operate in parallel
with the utility or another source. The
induction generator requires VARs from
an external source for it to generate
power. The induction generator
operates at a slip frequency so its
output frequency is automatically
locked in with the utility's frequency.
An induction generator is a popular
choice for use when designing
cogeneration systems, where it will
operate in parallel with the utility.
This type of generator offers certain
advantages over a synchronous
generator. For example, voltage and
frequency are controlled by the utility;
thus voltage and frequency regulators
are not required. In addition, the
generator construction offers high
reliability and little maintenance.
Also, a minimum of protective relays
and controls are required. Its major
disadvantages are that it requires
VARs from the system and it normally
cannot operate as a standby/
emergency generator.
Synchronous generators, however,
are the most common. Their output is
determined by their field and governor
controls. Varying the current in the
DC field windings controls the voltage
output. The frequency is controlled
by the speed of rotation. The torque
applied to the generator shaft by
the driving engine controls the power
output. In this manner, the synchronous generator offers precise control
over the power it can generate. In
cogeneration applications, it can be
used to improve the power factor of
the system.
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E
1.2-2

April 2016
Sheet 01 024
Generator Systems
Multiple Isolated Standby Generators
Emergency Standby Generator System
ii
1
2
3
4
5
6
7
There are primarily three types of

generator systems. The first and
simplest type is a single generator
that operates independently from
the electric utility power grid.
This is typically referred to as an
emergency standby generator
system. Figure 1.2-1 shows a single
standby generator, utility source
and a transfer switch. In this case, the
load is either supplied from the utility
or the generator. The generator and
the utility are never continuously
connected together. This simple radial
system has few requirements for
protection and control. It also has the
least impact on the complete electric
power distribution system. It should
be noted that this type of generator
system improves overall electrical
reliability but does not provide the
redundancy that some facilities require
if the generator fails to start or is out
for maintenance.
8
Utility
G1
10
11
ATS
12
13
14
Load
Figure 1.2-1. Emergency Standby

Generator System
The second type of generator system

is a multiple isolated set of standby
generators. Figure 1.2-2 shows
multiple generators connected to
a paralleling bus feeding multiple
transfer switches. The utility is the
normal source for the transfer switches.
The generators and the utility are never
continuously connected together in this
scheme. Multiple generators may be
required to meet the load requirements
(N system). Generators may be applied
in an N+1 or a 2N system for improved
system reliability.
Utility
G1
G2
Switchgear
ATS-1
ATS-2
Load 1
Load 2
Figure 1.2-2. Multiple Isolated Set of

Standby Generators
In an N system, where N is the number
of generators required to carry the
load; if a generator fails or is out for
maintenance, then the load may be
dropped. This is unacceptable for most
critical 24/7 operations. In an N + 1
system, N is the number of generators
needed to carry the load and 1 is
an extra generator for redundancy.
If one generator fails to start or is out
for maintenance, it will not affect the
load. In a 2N system, there is complete
100% redundancy in the standby
generation system such that the failure
of one complete set of generators
will not affect the load.
Multiple generator systems have a

more complex control and protection
requirement as the units have to be
synchronized and paralleled together.
The generators are required to share
the load proportionally without swings
or prolonged hunting in voltage or
frequency for load sharing. They may
also require multiple levels of load
shedding and/or load restoration
schemes to match generation capacity.
Multiple Generators Operating in

Parallel with Utility System
The third type of system is either one
with a single or multiple generators
that operate in parallel with the utility
system. Figure 1.2-3 shows two
generators and a utility source feeding
a switchgear lineup feeding multiple
loads. This system typically requires
generator capacity sufficient to carry
the entire load or sophisticated load
shedding schemes. This system will
require a complete and complex
protection and control scheme. The
electric utility may have very stringent
and costly protection requirements
for the system. IEEE standard 1547
describes the interconnection requirements for paralleling to the utility.
Utility
G1
G2
Switchgear
Load 1
Load 2
Load 3
Figure 1.2-3. Multiple Generators Operating

in Parallel with Utility System
15
16
17
18
19
20
21
CA08104001E
April 2016

1.2-3
Sheet 01 025
Generator Fundamentals
A generator consists of two primary
components, a prime mover and an
alternator. The prime mover is the
energy source used to turn the rotor
of the alternator. It is typically a
diesel combustion engine for most
emergency or standby systems.
In cogeneration applications, the
prime mover may come from a steam
driven turbine or other source. On
diesel units, a governor and voltage
regulator are used to control the speed
and power output.
The alternator is typically a synchronous machine driven by the prime
mover. A voltage regulator controls its
voltage output by adjusting the field.
The output of a single generator or
multiple paralleled generator sets is
controlled by these two inputs. The
alternator is designed to operate at a
specified speed for the required output
frequency, typically 60 or 50 Hz. The
voltage regulator and engine governor
along with other systems define the
generators response to dynamic
load changes and motor starting
characteristics.
Generators are rated in power and
voltage output. Most generators are
designed to operate at a 0.8 power
factor. For example, a 2000 kW
generator at 277/480 V would have a
kVA rating of 2500 kVA (2000 kW/
08 pf) and a continuous
current rating
of 3007A 2500 kVA 480V 3 .

Typical synchronous generators
for industrial and commercial
power systems range in size from
1003000 kVA and from 208 V13,800 V.
Other ratings are available and these
discussions are applicable to those
ratings as well.
Generators must be considered in the
short-circuit and coordination study
as they may greatly impact the rating
of the electrical distribution system.
This is especially common on large
installations with multiple generators
and systems that parallel with the
utility source. Short-circuit current
contribution from a generator
typically ranges from 8 to 12 times
full load amperes.
The application of generators requires

special protection requirements.
The size, voltage class, importance
and dollar investment will influence
the protection scheme associated with
the generator(s). Mode of operation
will influence the utility companys
interface protection requirements.
Paralleling with the electric utility is
the most complicated of the utility
inter-tie requirements. IEEE ANSI 1547
provides recommended practices.
Generator Grounding and Bonding

(Ref. NEC 2011, Article 250.30(A)(1)
and (2))
Generator grounding methods need
to be considered and may affect the
distribution equipment and ratings.
Generators may be connected in delta
or wye, but wye is the most typical
connection. A wye-connected generator
can be solidly grounded, low impedance
grounded, high impedance grounded
or ungrounded. Section 1.4 discusses
general grounding schemes, benefits
of each and protection considerations.
A solidly grounded generator may have
a lower zero sequence impedance than
its positive sequence impedance. In this
case, the equipment will need to be rated
for the larger available ground fault
current. The generators neutral may
be connected to the system-neutral; if
it is, the generator is not a separately
derived system and a three-pole transfer
switch is used. If the generators neutral
is bonded to ground separate from the
system-neutral, it is a separately
derived system and a four-pole transfer

switch is required or ground fault relays
could misoperate and unbalanced neutral current may be carried on ground
conductors.
An IEEE working group has studied the
practice of low resistance grounding
of medium voltage generators within
the general industry. This working
group found that, for internal generator
ground faults, the vast majority of the
damage is done after the generator
breaker is tripped offline, and the field
and turbine are tripped. This is due to
the stored energy in the generator flux
that takes several seconds to dissipate
after the generator is tripped offline.
It is during this time that the low
resistance ground allows significant
amounts of fault current to flow into
the ground fault. Because the large fault
currents can damage the generators
winding, application of an alternate
protection method is desirable during
this time period. One of the solutions
set forth by this working group is
a hybrid high resistance grounding
(HHRG) scheme as shown in
Figure 1.2-4. In the HHRG scheme,
the low resistance ground (LRG)
is quickly tripped offline when the
generator protection senses the
ground fault. The LRG is cleared
at the same time that the generator
breaker clears, leaving the high
resistance ground portion connected
to control the transient overvoltages
during the coast-down phase of the
generator, thereby all but eliminating
generator damage.
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
HRG
51G
Gen
86
Phase
Relays
R
R LRG
59G
14
87GN
15
16
17
Figure 1.2-4. Hybrid High Resistance Grounding Scheme
18
19
20
21
CA08104001E
1.2-4

April 2016
Sheet 01 026
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
Generator Controls
The engine generator set has controls
to maintain the output frequency
(speed) and voltage. These controls
consist of a governor and voltage
regulator. As loads change on the
system, the frequency and voltage
will change. The speed control will
then adjust the governor to correct
for the load (kW) change. The
voltage regulator will change the
field current to adjust the voltage
to the desired voltage value. These
are the basic controls found on all
synchronous generators.
Multiple generator systems require
more sophisticated controls. Generators
are paralleled in a multi-generator
system and they must share the load.
These systems often have a load shed
scheme, which adds to the complexity.
Multiple generator schemes need a
master controller to prevent units from
being connected out-of-phase. The
sequence of operation is to send a
start signal to all generators simultaneously. The first unit up to frequency
and voltage will be permitted to close
its respective breaker and energize the
paralleling bus. Breakers for the other
generators are held open, not permitted to close, until certain conditions
are met. Once the paralleling bus is
energized, the remaining generators
must be synchronized to it before
the generators can be paralleled.
Synchronization compares the voltage
phasors angle and magnitude. Both
generators must be operating at the
same frequency and phase-matched
within typically 5 to 10 degrees with
each other. The voltage magnitude
typically must be within 20 to 24%.
A synch-scope is typically supplied

on paralleling gear. The synch-scope
displays the relative relationship
between voltage phasors on the
generator to be paralleled and the
bus. If the generator is running slower
than the bus (less than 60 Hz) then the
needle on the scope will spin in the
counterclockwise direction. If it is
running faster, then it will rotate in
the clockwise direction. The greater
the frequency difference, the faster
is the rotation. It is important that the
generators are in phase before they
are paralleled. Severe damage will
occur if generators are paralleled
out-of-phase.
Generator Short-Circuit
Characteristics
If a short circuit is applied directly to
the output terminals of a synchronous
generator, it will produce an extremely
high current initially, gradually decaying
to a steady-state value. This change
is represented by a varying reactive
impedance. Three specific reactances
are used for short-circuit fault currents.
They are:
Subtransient reactance Xd, which is

used to determine the fault
current during the first 1 to 5 cycles
Transient reactance Xd, which is
used to determine the fault current
during the next 5 to 200 cycles
Synchronous reactance Xd, which is
used to determine the steady- state
fault current
The subtransient reactance Xd will

range from a minimum of approximately 9% for a two-pole, wound-rotor
machine to approximately 32% for a
low-speed, salient-pole, hydro-generator.
The initial symmetrical fault current
can be as much as 12 times full
load current.
Depending on the generator type,
the zero sequence impedance may be
less than the subtransient reactance
and the ground fault current substantially higher than the three-phase
short-circuit current. For example, a
2500 kVA, 480/277 V, four-pole, 2/3
pitch standby generator has a 0.1411
per unit subtransient reactance Xd
and a 0.033 per unit zero sequence Xo
reactance. The ground current is
approximately a third larger than the
three-phase fault current. The ground
fault current can be reduced to the
three-phase level by simply adding a
small reactance between the generator
neutral and ground while still being
considered solidly grounded.
The electric power system analysis
must be performed based on the worstcase operating conditions. Typically
this is when all sources are paralleled.
If the system can operate with both
the utility supply and generators in
parallel, then the equipment must be
rated for the combined fault current
plus motor contribution. If the generator
and utility will not be paralleled, then
both cases will need to be looked at
independently and the worst case used
for selecting the equipment ratings.
14
15
16
17
18
19
20
21
CA08104001E
April 2016

1.2-5
Sheet 01 027
Generator Protection
Generator protection will vary and
depend on the size of the generator,
type of system and importance of the
generator. Generator sizes are defined
as: small1000 kVA maximum up
to 600 V (500 kVA maximum when
above 600 V); medium over 1000 kVA
to 12,500 kVA maximum regardless
of voltage; largefrom 12,500
50,000 kVA. The simplest is a single
generator system used to feed emergency and/or standby loads. In this
case, the generator is the only source
available when it is operating and
it must keep operating until the
normal source returns.
Figure 1.2-5 Part (A) shows minimum
recommended protection for a single
generator used as an emergency or
standby system. Phase and ground
time overcurrent protection (Device
51 and 51G) will provide protection for
external faults. For medium voltage
generators, a voltage controlled time
overcurrent relay (Device 51V) is
recommended for the phase protection as it can be set more sensitive
than standard overcurrent relays and
is less likely to false operate on normal
overloads. This scheme may not
provide adequate protection for
internal generator faults when no
other power source exists. Local
generator controllers may offer
additional protection for voltage
and frequency conditions outside
the generators capabilities.
Figure 1.2-5 Part (B) shows the
recommended protection for multiple,
isolated, medium voltage, small
generators. Additional protection
may be desired and could include
generator differential, reverse power,
and loss of field protection. Differential
protection (Device 87) can be accomplished with either a self-balancing
set of CTs as in Figure 1.2-6 or with
a percentage differential scheme as
in Figure 1.2-7 on Page 1.2-6. The
percentage differential scheme
offers the advantage of reducing the
possibility for false tripping due to
CT saturation. The self-balancing
scheme offers the advantages of
increased sensitivity, needing three
current transformers in lieu of six,
and the elimination of current
transformer external wiring from
the generator location to the generator
switchgear location.
ANSI/IEEE
Std 242-1986
Generator Protection
ii
1
51
Alternate
Location
1
51V
32
40
1
2
3
51G
Gen
87
1
51
Preferred
Location
Gen
51G
(A)
(A) Single Isolated Generator on Low Voltage System

(B) Multiple Isolated Generator on Medium Voltage System
Figure 1.2-5. Typical Protective Relaying Scheme for Small Generators
(B)
6
7
8
9
50/5A
87-1
50/5A
87-2
50/5A
87-3
10
11
12
13
Gen
14
15
16
Figure 1.2-6. Self-Balancing Generator

Differential Relay Scheme
17
18
19
20
21
CA08104001E
1.2-6

April 2016
Sheet 01 028
i
ii
1
2
3
4
5
6
7
Reverse power protection (Device 32)

is used to prevent the generator
from being motored. Motoring could
damage (with other hazards) the prime
mover. A steam turbine could overheat
and fail. A diesel or gas engine could
either catch fire or explode. A steam
turbine can typically withstand approximately 3% reverse power where a
diesel engine can withstand up to 25%
reverse power.
Loss of field protection (Device 40) is
needed when generators are operating
in parallel with one another or the
power grid. When a synchronous
generator loses its field, it will continue
to generate power as an induction
generator obtaining its excitation from
the other machines on the system.
During this condition, the rotor will
quickly overheat due to the slip
frequency currents induced in it. Loss
of excitation in one machine could
jeopardize the operation of the other
machines beyond their capability and
the entire system.
Grounding
Resistor
51G
87
01
PC
R1
R1
02
R2
Gen
OC
R2
03
87G
R3
R3
52
8
9
To Main Bus
10
11
OC = Operating coil
PC = Permissive coil
Figure 1.2-7. Generator Percentage Differential Relay (Phase Scheme)

and Ground Differential Scheme Using a Directional Relay
12
13
14
15
16
17
18
19
20
21
CA08104001E
April 2016

1.2-7
Sheet 01 029
Typical protection for larger generators

is shown in Figure 1.2-8. It adds
phase unbalance and field ground
fault protection. Phase unbalance
(Device 46) or negative sequence
overcurrent protection prevents the
generators rotor from overheating
damage. Unbalanced loads, fault
conditions or open phasing will
produce a negative sequence current
to flow. The unbalanced currents
induce double system frequency
currents in the rotor, which quickly
causes rotor overheating. Serious
damage will occur to the generator if
the unbalance is allowed to persist.
i
3
81U/O
1
27/59
Many modern protective relays are

microprocessor-based and provide a
full complement of generator protection
functions in a single package. The cost
per protection function has been
drastically reduced such that it is
feasible to provide more complete
protection even to smaller generators.
1
40
51V
3
Other protection functions such as

under/overvoltage (Device 27/59) could
be applied to any size generator. The
voltage regulator typically maintains
the output voltage within its desired
output range. This protection can
provide backup protection in case the
voltage regulator fails. Under/over
frequency protection (Device 81U/81O)
could be used for backup protection
for the speed control. Sync check
relays (Device 25) are typically applied
as a breaker permissive close function
where generators are paralleled.
ii
87B
1
32
46
1
87
87G
60
Voltage Regulator and
Metering Circuits
64
1
49
7
Gen
E
8
51G
9
10
11
Figure 1.2-8. Typical Protective Relaying Scheme for Large Generator
12
IEEE ANSI 1547 provides recommended

practices for utility inter-tie protection.
If the system has closed- transition or
paralleling capability, additional protection may be required by the utility.
Typically, no additional protection is
required if the generator is paralleled
to the utility for a maximum of 100
msec or less. Systems that offer soft
transfer, peak shaving or co-generation
will require additional utility inter-tie
protection. The protection could
include directional overcurrent and
power relays and even transfer trip
schemes. Please consult your local
utility for specific requirements.
13
14
15
16
17
18
19
20
21
CA08104001E
1.2-8

April 2016
Sheet 01 030
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Generator Set Sizing

and Ratings
Many factors must be considered
when determining the proper size or
electrical rating of an electrical power
generator set. The engine or prime
mover is sized to provide the actual
or real power in kW, as well as speed
(frequency) control through the use
of an engine governor. The generator
is sized to supply the kVA needed at
startup and during normal running
operation and it also provides voltage
control using a brushless exciter and
voltage regulator. Together the engine
and generator provide the energy
necessary to supply electrical loads
in many different applications
encountered in todays society.
The generator set must be able to
supply the starting and running
electrical load. It must be able to
pick up and start all motor loads and
low power factor loads, and recover
without excessive voltage dip or
extended recovery time. Nonlinear
loads like variable frequency drives,
uninterruptible power supply (UPS)
systems and switching power supplies
also require attention because the SCR
switching causes voltage and current
waveform distortion and harmonics.
The harmonics generate additional
heat in the generator windings, and
the generator may need to be upsized
to accommodate this. The type of
fuel (diesel, natural gas, propane, etc.)
used is important as it is a factor in
determining generator set transient
response. It is also necessary to
determine the load factor or average
power consumption of the generator
set. This is typically defined as the load
(kW) x time (hrs. while under that
particular load) / total running time.
When this load factor or average
power is taken into consideration
with peak demand requirements
and the other operating parameters
mentioned above, the overall electrical
rating of the genset can be determined.
Other items to consider include the
unique installation, ambient, and site
requirements of the project. These
will help to determine the physical
configuration of the overall system.
Typical rating definitions for diesel

gensets are: standby, prime plus 10,
continuous and load management
(paralleled with or isolated from
utility). Any diesel genset can have
several electrical ratings depending
on the number of hours of operation
per year and the ratio of electrical
load/genset rating when in operation.
The same diesel genset can have a
standby rating of 2000 kW at 0.8 power
factor (pf) and a continuous rating of
1825 kW at 0.8 pf. The lower continuous
rating is due to the additional hours
of operation and higher load that the
continuous genset must carry. These
additional requirements put more
stress on the engine and generator
and therefore the rating is decreased
to maintain longevity of the equipment.
Different generator set manufacturers
use basically the same diesel genset
electrical rating definitions and these
are based on international diesel
fuel stop power standards from
organizations like ISO, DIN and others.
A standby diesel genset rating is
typically defined as supplying varying
electrical loads for the duration of a
power outage with the load normally
connected to utility, genset operating
<100 hours per year and no overload
capability. A prime plus 10 rating is
typically defined as supplying varying
electrical loads for the duration of a
power outage with the load normally
connected to utility, genset operating
500 hours per year and overload
capability of 10% above its rating for
1 hour out of 12. A continuous rating
is typically defined as supplying
unvarying electrical loads (i.e., base
loaded) for an unlimited time. The load
management ratings apply to gensets
in parallel operation with the utility
or isolated/islanded from utility and
these ratings vary in usability from
<200 hours per year to unlimited
usage. Refer to generator set manufacturers for further definitions on load
management ratings, load factor or
average power consumption, peak
demand and how these ratings are
typically applied. Even though there is
some standardization of these ratings
across the manufacturers, there also
exists some uniqueness with regard to
how each manufacturer applies their
generator sets.
19
Electrical rating definitions for natural

gas powered gensets are typically
defined as standby or continuous with
definitions similar to those mentioned
above for diesels. Natural gas gensets
recover more slowly than diesel gensets
when subjected to block loads. Diesel
engines have a much more direct path
from the engine governor and fuel
delivery system to the combustion
chamber and this results in a very
responsive engine-generator. A natural
gas engine is challenged with air-fuel
flow dynamics and a much more indirect path from the engine governor
(throttle actuator) and fuel delivery
system (natural gas pressure regulator,
fuel valve and actuator, carburetor
mixer, aftercooler, intake manifold) to
the combustion chamber and this results
in a less responsive engine-generator.
Diesel gensets recover about twice as
fast as natural gas gensets.
For the actual calculations involved
for sizing a genset, there are readily
accessible computer software programs
that are available on the genset manufacturers Internet sites or from the
manufacturers dealers or distributors.
These programs are used to quickly
and accurately size generator sets for
their application. The programs take
into consideration the many different
parameters discussed above, including
the size and type of the electrical loads
(resistive, inductive, SCR, etc.), reduced
voltage soft starting devices (RVSS),
motor types, voltage, fuel type, site
conditions, ambient conditions and
other variables. The software will
optimize the starting sequences of the
motors for the least amount of voltage
dip and determine the starting kVA
needed from the genset. It also provides
transient response data, including
voltage dip magnitude and recovery
duration. If the transient response is
unacceptable, then design changes can
be considered, including oversizing
the generator to handle the additional
kvar load, adding RVSS devices to
reduce the inrush current, improving
system power factor and other methods.
The computer software programs are
quite flexible in that they allow changes
to the many different variables and
parameters to achieve an optimum
design. The software allows, for
example, minimizing voltage dips
or using paralleled gensets vs. a
single genset.
20
21
CA08104001E

April 2016
1.2-9
Sheet 01 031
Genset Sizing Guidelines

Some conservative rules of thumb
for genset sizing include:
1. Oversize genset 2025%
for reserve capacity and for
motor starting.
2. Oversize gensets for unbalanced
loading or low power factor
running loads.
3. Use 1/2 hp per kW for motor loads.
4. For variable frequency drives,
oversize the genset by at
least 40%.
5. For UPS systems, oversize the
genset by 40% for 6 pulse and
15% for 6 pulse with input filters or
12 pulse.
6. Always start the largest motor
first when stepping loads.
For basic sizing of a generator system,
the following example could be used:
Generator Set Installation

and Site Considerations
There are many different installation
parameters and site conditions
that must be considered to have a
successful generator set installation.
The following is a partial list of areas
to consider when conducting this
design. Some of these installation
parameters include:
Step 1: Calculate Running Amperes
Motor loads:
200 hp motor. . . . . . . . . . . . .156 A
100 hp motor . . . . . . . . . . . . . .78 A
60 hp motor . . . . . . . . . . . . . . .48 A
Lighting load . . . . . . . . . . . . . . . .68 A
Miscellaneous loads . . . . . . . . . .95 A
Running amperes . . . . . . . . . . .445 A
Foundation type (crushed rock,

concrete, dirt, wood, separate
concrete inertia pad, etc.)
Foundation to genset vibration
dampening (spring type, cork
and rubber, etc.)
Noise attenuation (radiator fan
mechanical noise, exhaust noise,
air intake noise)
Combustion and cooling air
requirements
Exhaust backpressure requirements
Emissions permitting
Delivery and rigging requirements
Genset derating due to high
altitudes or excessive ambient
temperatures
Hazardous waste considerations

for fuel, antifreeze, engine oil
Meeting local building and
electrical codes
Genset exposure (coastal
conditions, dust, chemicals, etc.)
Properly sized starting systems
(compressed air, batteries
and charger)
Allowing adequate space for
installation of the genset and for
maintenance (i.e., air filter removal,
oil changing, general genset
inspection, etc)
Flex connections on all systems that
are attached to the genset and a
rigid structure (fuel piping, foundation vibration isolators, exhaust, air
intake, control wiring, power cables,
radiator flanges/duct work, etc.)
Diesel fuel day tank systems
(pumps, return piping)
Fuel storage tank (double walled,
fire codes) and other parameters
Please see the generator set manufacturers application and installation

guidelines for proper application
and operation of their equipment.
i
ii
1
2
3
4
5
6
7
8
9
10
11
Step 2: Calculating Starting Amperes

Using 1.25 Multiplier
Motor loads:
. . . . . . . . . . . . . . . . . . . . . . . .195 A
. . . . . . . . . . . . . . . . . . . . . . . . .98 A
. . . . . . . . . . . . . . . . . . . . . . . . .60 A
Lighting load . . . . . . . . . . . . . . . .68 A
Miscellaneous loads . . . . . . . . . .95 A
Starting amperes . . . . . . . . . . .516 A
12
Step 3: Selecting kVA of Generator
15
13
14
Running kVA =
(445 A x 480 V x 1.732)/
1000 = 370 kVA
Starting kVA =
(516 A x 480 V x 1.732)/
1000 = 428 kVA
16
17
Solution
Generator must have a minimum
starting capability of 428 kVA and
minimum running capability of 370 kVA.
18
Figure 1.2-9. Typical Genset Installation
Note: Courtesy of Caterpillar, Inc.
Also, please see section Factors

Governing Voltage Drop on
Page 1.3-21 for further discussion
on generator loading and reduced voltage starting techniques for motors.
CA08104001E
19
20
21

April 2016
Sheet 01 032
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

System Analysis
April 2016
1.3-1
Sheet 01 033
Systems Analysis
A major consideration in the
design of a distribution system is to
ensure that it provides the required
quality of service to the various
loads. This includes serving each
load under normal conditions and,
under abnormal conditions, providing
the desired protection to service
and system apparatus so that
interruptions of service are minimized
consistent with good economic and
mechanical design.
Under normal conditions, the important technical factors include voltage
profile, losses, load flow, effects of
motor starting, service continuity and
reliability. The prime considerations
under faulted conditions are apparatus
protection, fault isolation and service
continuity. During the system preliminary planning stage, before selection
of the distribution apparatus, several
distribution systems should be analyzed and evaluated, including both economic and technical factors. During this
stage, if system size or complexity warrant, it may be appropriate to provide a
thorough review of each system under
both normal and abnormal conditions.
The principal types of computer

programs used to provide system
studies include:
Short circuitidentify three-phase

and line-to-ground fault currents
and system impedances
Arc flashcalculates arc flash
energy levels, which leads to the
selection of personal protective
equipment (PPE)
Circuit breaker dutyidentify
asymmetrical fault current based
on X/R ratio
Protective device coordination
determine characteristics and settings of medium voltage protective
relays and fuses, and entire low
voltage circuit breaker and fuse
coordination
Load flowsimulate normal
load conditions of system
voltages, power factor, line
and transformer loadings
Motor startingidentify system
voltages, motor terminal voltage,
motor accelerating torque, and
motor accelerating time when
starting large motors
Short-circuit calculations define

momentary and steady-state fault
currents for LV and MV breaker and
fuse duty and bus bracings at any
selected location in the system, and also
determine the effect on the system
after removal of utility power due to
breaker operation or scheduled power
outages. Computer software programs
can identify the fault current at any
bus, in every line or source connected
to the faulted bus, or to it and every
adjacent bus, or to it and every bus
that is one and two buses away, or
currents in every line or source in the
system. The results of these calculations
permit optimizing service to the loads
while properly applying distribution
apparatus within their intended limits.
The following additional studies
should be considered depending
upon the type and complexity of the
distribution system, the type of facility
and the type of loads to be connected
to the system:
Harmonic analysis
Transient stability
Insulation coordination
Grounding study
Switching transient
Eatons Electrical Services & Systems

division can provide the studies
enumerated above.
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E
1.3-2

System Analysis
April 2016
Sheet 01 034
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Short-Circuit Currents
General
The amount of current available in a
short-circuit fault is determined by the
capacity of the system voltage sources
and the impedances of the system,
including the fault. Voltage sources
include the power supply (utility or
on-site generation) plus all rotating
machines connected to the system at
the time of the fault. A fault may be
either an arcing or bolted fault. In an
arcing fault, part of the circuit voltage is
consumed across the fault and the total
fault current is somewhat smaller than
for a bolted fault, so the latter is the
worst condition, and therefore is the
value sought in the fault calculations.
Basically, the short-circuit current is
determined by applying Ohms Law
to an equivalent circuit consisting of
a constant voltage source and a timevarying impedance. A time-varying
impedance is used in order to account
for the changes in the effective voltages
of the rotating machines during the
fault. In an AC system, the resulting
short-circuit current starts out higher in
magnitude than the final steady-state
value and asymmetrical (due
to the DC offset) about the X-axis.
The current then decays toward a
lower symmetrical steady-state value.
The time-varying characteristic of the
impedance accounts for the symmetrical decay in current. The ratio of the
reactive and resistive components (X/R
ratio) accounts for the DC decay, see
Figure 1.3-1. The fault current consists
of an exponentially decreasing directcurrent component superimposed
upon a decaying alternating-current.
The rate of decay of both the DC and
AC components depends upon the
ratio of reactance to resistance (X/R)
of the circuit. The greater this ratio,
the longer the current remains higher
than the steady-state value that it
would eventually reach.
The total fault current is not symmetrical
with respect to the time-axis because
of the direct-current component, hence
it is called asymmetrical current. The
DC component depends on the point
on the voltage wave at which
the fault is initiated.
See Table 1.3-2 for multiplying factors
that relate the rms asymmetrical value
of total current to the rms symmetrical
value, and the peak asymmetrical
value of total current to the rms
symmetrical value.
The AC component is not constant

if rotating machines are connected
to the system because the impedance
of this apparatus is not constant. The
rapid variation of motor and generator
impedance is due to these factors:
Subtransient reactance (x d" ), determines fault current during the first
cycle, and after about 6 cycles this
value increases to the transient reactance. It is used for the calculation
of the momentary interrupting and/or
momentary withstand duties of
equipment and/or system.
Transient reactance (x d
' ), which determines fault current after about 6 cycles
and this value in 1/2 to 2 seconds
increases to the value of the synchronous reactance. It is used in the setting
of the phase OC relays of generators
and medium voltage circuit breakers.
Synchronous reactance (xd ), which
determines fault current after steadystate condition is reached. It has no
effect as far as short-circuit calculations
are concerned, but is useful in the
determination of relay settings.
Transformer impedance, in percent, is
defined as that percent of rated primary
voltage that must be applied to the
transformer to produce rated current
flowing in the secondary, with secondary shorted through zero resistance.
Therefore, assuming the primary
voltage can be sustained (generally
referred to as an infinite or unlimited
supply), the maximum current a transformer can deliver to a fault condition is
the quantity of (100 divided by percent
impedance) times the transformer rated
secondary current. Limiting the power

source fault capacity will thereby
reduce the maximum fault current from
the transformer.
The electric network that determines
the short-circuit current consists of an
AC driving voltage equal to the pre-fault
system voltage and an impedance
corresponding to that observed when
looking back into the system from the
fault location. In medium and high
voltage work, it is generally satisfactory
to regard reactance as the entire
impedance; resistance may be
neglected. However, this is normally
permissible only if the X/R ratio of the
medium voltage system is equal to or
more than 25. In low voltage (1000 V
and below) calculations, it is usually
worthwhile to attempt greater accuracy
by including resistance with reactance
in dealing with impedance. It is for this
reason, plus ease of manipulating the
various impedances of cables and
buses and transformers of the low
voltage circuits, that computer studies
are recommended before final selection
of apparatus and system arrangements.
When evaluating the adequacy
of short-circuit ratings of medium
voltage circuit breakers and fuses,
both the rms symmetrical value and
asymmetrical value of the short-circuit
current should be determined.
For low voltage circuit breakers and
fuses, the rms symmetrical value
should be determined along with
either: the X/R ratio of the fault
at the device or the asymmetrical
short- circuit current.
Total CurrentA Wholly Offset

Asymmetrical Alternating Wave
3.0
2.5
rms Value of Total Current

Alternating Component Symmetrical Wave
rms Value of
Alternating Component
2.0
Scale of Curent Values
1.5
1.0
0.5
1
0
0.5
1.0
1.5
Direct ComponentThe Axis

Time in Cycles of
of Symmetrical Wave
a 60 Hz Wave
2.0
Figure 1.3-1. Structure of an Asymmetrical Current Wave

CA08104001E

System Analysis
April 2016
1.3-3
Sheet 01 035
Fault Current Waveform Relationships

The following Figure 1.3-2 describes
the relationship between fault
current peak values, rms symmetrical
values and rms asymmetrical values
depending on the calculated X/R ratio.
The table is based on the following
general formulas:
1.
Ip = I 2
Ip
----- = 2
I
Peak multiplication factor =
t
-------------
1 + e X R
2. I rms asym = I 1 + 2e
Based on a 60 Hz system and t = 1/2 cycle

(ANSI/IEEE C37.13.1990/10.1.4)
260
----------------120 ---------------
1 + e X R =
2 260
--------------------------------120
--------------------------------XR
I rms asym
rms multiplication factor =
------------------------------ =
1 + 2e
ii
----------1 + e X R
1 + 2e
1
2
2
------------XR
Example for X/R =15
2t
--------------XR
Peak mf = 2
Where:
-------
1 + e 15 =
4
2.5612
I = Symmetrical rms current

2
-----------
Ip = Peak current
rms mf = 1 + 2e
15
1.5217
e = 2.718
=2f
f = Frequency in Hz
t = Time in seconds
9
10
2.6
2.5
2.4
2.3
FA
C
1.7
11
12
13
14
1.6
LT
IP
LI
2.0
1.5
PE
AK
1.9
1.8
ON
OR
CT
FA
1.4
TI
ICA
1.7
1.3
L
TIP
UL
SM
1.6
1.2
RM
1.1
1.5
1.4
1.5
2.5
8 9 10
15
20
25
CIRCUIT X/R RATIO (TAN PHASE)
30
40
50
60 70 80 90 100
RMS MULTIPLICATION FACTOR =
CA
TI
2.1
PEAK MULTIPLICATION FACTOR =
1.8
TO
R
2.2
RMS SYMMETRICAL
rms Asym = DC 2 + rms Sym2

with DC Value
Taken at Current Peak
Based Upon:
RMS MAXIMUM ASYMMETRICAL
2.7
RMS SYMMETRICAL
PEAK MAXIMUM ASYMMETRICAL
2.8
15
16
17
18
19
20
Figure 1.3-2. Relation of X/R Ratio to Multiplication Factor
21
CA08104001E
1.3-4

System Analysis
April 2016
Sheet 01 036
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

The calculation of asymmetrical
currents is a laborious procedure since
the degree of asymmetry is not the
same on all three phases. It is common
practice for medium voltage systems,
to calculate the rms symmetrical fault
current, with the assumption being
made that the DC component has
decayed to zero, and then apply
a multiplying factor to obtain the first
half-cycle rms asymmetrical current,
which is called the momentary
current. For medium voltage systems
(defined by IEEE as greater than
1000 V up to 69,000 V) the multiplying
factor is established by NEMA and
ANSI standards depending upon the
operating speed of the breaker. For
low voltage systems, short-circuit
study software usually calculates the
symmetrical fault current and the
faulted system X/R ratio using ANSI
guidelines. If the X/R ratio is within the
standard, and the breaker interrupting
current is under the symmetrical fault
value, the breaker is properly rated.
If the X/R ratio is higher than ANSI
standards, the study applies a multiplying factor to the symmetrical
calculated value (based on the
X/R value of the system fault) and
compares that value to the breaker
symmetrical value to assess if it is
properly rated. In the past, especially
using manual calculations, a multiplying factor of 1.17 (based on the use
of an X/R ratio of 6.6 representing
a source short-circuit power factor
of 15%) was used to calculate the
asymmetrical current. These values
take into account that medium voltage
breakers are rated on maximum
asymmetry and low voltage breakers
are rated average asymmetry.
Synchronous motorsuse 5.0 times

motor full load current (impedance
value of 20%).
When the motor load is not known,
the following assumptions generally
are made:
208Y/120 V Systems
Assume 50% lighting and 50%

motor load
Assume motor feedback contribution of twice full load current of

transformer
or
or
Medium Voltage Motors

If known, use actual values otherwise
use the values indicated for the same
type of motor.
Calculation Methods
The following pages describe various
methods of calculating short-circuit
currents for both medium and low
voltage systems. A summary of
the types of methods and types of
calculations is as follows:
240/480/600 V Three-Phase, Three-Wire or

Four-Wire Systems
Assume 100% motor load
or
Assume motors 25% synchronous

and 75% induction
or
Assume motor feedback contribution of four times full load current

of transformer
480Y/277 V Systems in Commercial Buildings
Assume 50% induction motor load

or
Assume motor feedback contribution of two times full load current

of transformer or source
To determine the motor contribution

during the first half-cycle fault current,
when individual motor horsepower
load is known, the subtransient
reactances found in the IEEE Red Book
should be used in the calculations.
When the system motor load is
unknown, the following assumptions
generally are made:
Induction motorsuse 4.0 times

motor full load current (impedance
value of 25%).
Note: For motors fed through adjustable

frequency drives or solid-state soft starters,
there is no contribution to fault current, unless
1) they have an internal run contactor or
2) they have a bypass contactor.
Medium voltage
switchgearexact
method . . . . . . . . . . . . . . Page 1.3-5
Medium voltage
switchgearquick
check table . . . . . . . . . . . Page 1.3-7
Medium voltage
switchgear
Example 1verify
ratings of breakers . . . . Page 1.3-8
Medium voltage
switchgear
Example 2verify
ratings of breakers
with rotating
loads . . . . . . . . . . . . . . . . Page 1.3-9
Medium voltage
switchgear Example 3
verify ratings of
breakers with
generators . . . . . . . . . . . Page 1.3-10
Medium voltage
fusesexact method . . Page 1.3-11
Power breakers
asymmetry
derating factors . . . . . . . Page 1.3-11
Molded-case
breakersasymmetry
derating factors . . . . . . . Page 1.3-12
Short-circuit
calculations
short cut method
for a system . . . . . . . . . . Page 1.3-13
Short-circuit
calculationsshort
cut method for
end of cable . . . . . . . . . . Page 1.3-15
Short-circuit
calculations
short cut method
for end of cable
chart method . . . . . . . . . Page 1.3-16
Short-circuit currents
chart of transformers
3003750 kVA. . . . . . . . . Page 1.5-9
21
CA08104001E
April 2016

System Analysis
1.3-5
Sheet 01 037

for Specific Equipment
Exact Method
a voltage = maximum rated voltage

divided by K (for example, 4.76/1.24 =
3.85). If this breaker is applied in a
system rated at 2.4 kV, the calculated
fault current must be less than 36 kA.
greater than the available system fault

current of 20,000 A, the breaker is
acceptable (assumes the breakers
momentary and fault close rating is
also acceptable).
The purpose of the fault current calculations is to determine the fault current
at the location of a circuit breaker, fuse
or other fault interrupting device in
order to select a device adequate for the
calculated fault current or to check the
thermal and momentary ratings of noninterrupting devices. When the devices
to be used are ANSI-rated devices, the
fault current must be calculated and the
device selected as per ANSI standards.
For example, consider the following case:
Note: If the system available fault current

were 22,000 A symmetrical, this breaker
could not be used even though the
Maximum Symmetrical Interrupting
Capability is greater than 22,000 because
Test 1 calculation is not satisfied.
The calculation of available fault current

and system X/R rating is also used to
verify adequate busbar bracing and
momentary withstand ratings of
devices such as contactors.
Medium Voltage VCP-W

Metal-Clad Switchgear
The applicable ANSI Standards, C37
is the latest applicable edition. The
following is a review of the meaning
of the ratings. (See Tab 5, Section 5.4.)
Assume a 12.47 kV system with

20,000 A symmetrical available. In
order to determine if an Eaton Type
150 VCP-W 500 vacuum breaker is
suitable for this application, check
the following:
From Table 5.4-1B in Tab 5, Section 5.4
under column Rated Maximum
Voltage V = 15 kV, under column
Rated short-circuit Current I = 18 kA,
Rated Voltage Range Factor K = 1.3.
Test 1 for V/Vo x I or 15 kV/12.47 kV x 18
kA = 21.65; also check K x I (which
is shown in the column headed
Capability) or 1.3 x 18 kA = 23.4 kA.
Because both of these numbers are
K-Rated Voltage Factor

The rated voltage divided by this factor
determines the system kV a breaker can
be applied up to the short-circuit kVA
rating calculated by the formula
3 Rated SC Current Rated Max. Voltage
Note: Interrupting capabilities of some of

todays vacuum breakers may have K = 1,
whereby the interrupting current is constant
across its entire operating range.
Rated Short-Circuit Current

This is the symmetrical rms value of
current that the breaker can interrupt
at rated maximum voltage. It should
be noted that the product 3 x 4.76 x
29,000 = 239,092 kVA is less than the
nominal 250,000 kVA listed. This rating
(29,000 A) is also the base quantity
that all the related capabilities are
referred to.

Capability
This is expressed in rms symmetrical
amperes or kiloamperes and is K x I
rated; 29,000 x 1.24 = 35,960 rounded
to 36 kA.
This is the rms symmetrical current
that the breaker can interrupt down to
CA08104001E
ii
1
2
3
4
5
6
7
Table 1.3-1. Reactance X

System
Component
Reactance X Used for
Typical Values and Range

Short-Circuit Close and Latch on Component Base
Duty
(Momentary)
% Reactance X/R Ratio
Two-pole turbo generator

Four-pole turbo generator
X
X
X
X
9 (714)
15 (1217)
80 (40120)
80 (40120)
Hydro generator with damper wedges

and synchronous condensers
20 (1332)
30 (1060)
Hydro generator without damper windings
0.75X
0.75X
16 (1650)
30 (1060)
The Rated Maximum Voltage

This designates the upper limit of
design and operation of a circuit
breaker. For example, a circuit breaker
with a 4.76 kV rated maximum voltage
cannot be used in a 4.8 kV system.
For approximate calculations, Table 1.3-1

provides typical values of % reactance
(X) and X/R values for various rotating
equipment and transformers. For simplification purposes, the transformer
impedance (Z) has been assumed to be
primarily reactance (X). In addition, the
resistance (R) for these simplified calculations has been ignored. For detailed
calculations, the values from the IEEE
Red Book Standard 141, for rotating
machines, and ANSI C57 and/or C37
for transformers should be used.
All synchronous motors
1.5X
1.0X
20 (1335)
30 (1060)
Induction motors above 1000 hp, 1800 rpm

and above 250 hp, 3600 rpm
1.5X
1.0X
17 (1525)
30 (1540)
All other induction motors 50 hp and above
3.0X
1.2X
17 (1525)
15 (240)
Induction motors below 50 hp and

all single-phase motors
Neglect
Neglect
Distribution system from remote

transformers
As specified
or calculated
15 (515)
Current limiting reactors
As specified
or calculated
80 (40120)
OA to 10 MVA, 69 kV
FOA 1230 MVA
FOA 40100 MVA
8.0
8.0 to 10.5
Depends on
primary
windings BIL
rating
11
12
13
14
Transformers
OA to 10 MVA, above 69 kV
10
18 (724)
18 (724)
20 (730)
38 (3244)
15
16
Table 1.3-2. Typical System X/R Ratio Range (for Estimating Purposes)
17
Type of Circuit
X/R Range
Remote generation through other types of circuits such as transformers rated 10 MVA
or smaller for each three-phase bank, transmission lines, distribution feeders, etc.
15 or less
Remote generation connected through transformer rated 10 MVA to 100 MVA

for each three-phase bank, where the transformers provide 90% or more
of the total equivalent impedance to the fault point
1540
Remote generation connected through transformers rated 100 MVA or larger

for each three-phase bank where the transformers provide 90% or more
of the total equivalent impedance to the fault point
3050
19
Synchronous machines connected through transformers rated 25100 MVA

for each three-phase bank
3050
20
Synchronous machines connected through transformers rated 100 MVA and larger
4060
Synchronous machines connected directly to the bus or through reactors
40120
18
21
1.3-6

System Analysis
April 2016
Sheet 01 038
i
ii
1
2
3
4
5
6
7
8
9
10
The Close and Latch Capability

This is also a related quantity
expressed in rms asymmetrical
amperes by 1.6 x maximum
symmetrical interrupting capability.
For example, 1.6 x 36 = 57.6 or 58 kA, or
1.6 K x rated short-circuit current.
Another way of expressing the close
and latch rating is in terms of the peak
current, which is the instantaneous
value of the current at the crest. ANSI
Standard C37.09 indicates that the ratio
of the peak to rms asymmetrical value
for any asymmetry of 100% to 20%
(percent asymmetry is defined as the
ratio of DC component of the fault in
per unit to 2 ) varies not more than
2% from a ratio of 1.69. Therefore, the
close and latch current expressed in
terms of the peak amperes is = 1.6 x
1.69 x K x rated short-circuit current.
In the calculation of faults for the purposes of breaker selection, the rotating
machine impedances specified in ANSI
Standard C37.010 Article 5.4.1 should
be used. The value of the impedances
and their X/R ratios should be obtained
from the equipment manufacturer. At
initial short-circuit studies, data from
manufacturers is not available. Typical
values of impedances and their X/R
ratios are given in Table 1.3-1.
The steps in the calculation of fault

currents and breaker selection are
described hereinafter:
Step 1: Collect the X and R data of the
circuit elements. Convert to a common
kVA and voltage base. If the reactances
and resistances are given either in
ohms or per unit on a different voltage
or kVA base, all should be changed
to the same kVA and voltage base. This
caution does not apply where
the base voltages are the same as
the transformation ratio.
Step 2: Construct the sequence
networks and connect properly for
the type of fault under consideration.
Use the X values required by ANSI
Standard C37.010 for the interrupting
duty value of the short-circuit current.
Step 3: Reduce the reactance network

to an equivalent reactance. Call this
reactance XI.
Step 4: Set up the same network for
resistance values.
Step 5: Reduce the resistance network
to an equivalent resistance. Call this
resistance RI. The above calculations
of XI and RI may be calculated by
several computer programs.
Step 6: Calculate the E/XI value, where
E is the prefault value of the voltage at
the point of fault nominally assumed
1.0 pu.
X
Step 7: Determine X/R = ------I as
RI
previously calculated.
Step 8: Go to the proper curve for
the type of fault under consideration
(three-phase, phase-to-phase, phaseto-ground), type of breaker at the location (2, 3, 5 or 8 cycles), and contact
parting time to determine the multiplier to the calculated E/XI.
See Figures 1.3-3, 1.3-4 and 1.3-5 for
5-cycle breaker multiplying factors.
Use Figure 1.3-5 if the short circuit is
fed predominantly from generators
removed from the fault by two or more
130
130
130
120
120
120
110
110
19
20
21
80
80
40
3
TIME
PA
RT
ING
60
70
60
50
50
40
40
NT
AC
T
NT
AC
50
70
CO
60
Ratio X/R
T P
ART
ING
70
Ratio X/R
TIME
80
90
12
90
10
90
30
30
18
100
CO
17
Ratio X/R
14
16
100
100
13
15
110
12
11
The ANSI Standard C37.010 allows the

use of the X values only in determining the E/X value of a fault current. The
R values are used to determine the X/R
ratio, in order to apply the proper
multiplying factor, to account for the
total fault clearing time, asymmetry,
and decrement of the fault current.
5-CYCLE
BREAKER
30
5-CYCLE
BREAKER
20
20
20
10
10
10
1.0 1.1 1.2 1.3 1.4

Multiplying Factors for E / X Amperes
Figure 1.3-3. Three-phase Fault Multiplying

Factors that Include Effects of AC and
DC Decrement
1.0
1.1
1.2
1.3
1.4
Figure 1.3-4. Line-to-Ground Fault Multiplying

Factors that Include Effects of AC and
DC Decrement
5-CYCLE
BREAKER
1.0
1.1
1.2
1.3
1.4
Figure 1.3-5. Three-phase and Line-to-Ground

Fault Multiplying Factors that Include Effects
of DC Decrement Only
CA08104001E

System Analysis
April 2016
1.3-7
Sheet 01 039
transformations or the per unit reactance external to the generation is 1.5

times or more than the subtransient
reactance of the generation on a common base. Also use Figure 1.3-5 where
the fault is supplied by a utility only.
Step 9: Interrupting duty short-circuit
current = E/XI x MFx = E/X2.
Step 10: Construct the sequence
(positive, negative and zero) networks
properly connected for the type of fault
under consideration. Use the
X values required by ANSI Standard
C37.010 for the Close and Latch
duty value of the short-circuit current.
Step 11: Reduce the network to an
equivalent reactance. Call the reactance X. Calculate E/X x 1.6 if the
breaker close and latch capability is
given in rms amperes or E/X x 2.7 if
the breaker close and latch capability
is given in peak or crest amperes.
Step 12: Select a breaker whose:
Application Quick Check Table
The ANSI standards do not require the

inclusion of resistances in the calculation of the required interrupting and
close and latch capabilities. Thus the
calculated values are conservative.
However, when the capabilities of
existing switchgears are investigated,
the resistances should be included.
For application of circuit breakers in a

radial system supplied from a single
source transformer. Short-circuit duty
was determined using E/X amperes
and 1.0 multiplying factor for X/R ratio
of 15 or less and 1.25 multiplying
factor for X/R ratios in the range of
15 to 40.
For single line-to-ground faults, the

symmetrical interrupting capability
is 1.15 x the symmetrical interrupting
capability at any operating voltage,
but not to exceed the maximum
symmetrical capability of the breaker.
Application Above 3,300 ft (1,000 m)

The rated one-minute power frequency
withstand voltage, the impulse withstand voltage, the continuous current
rating, and the maximum voltage rating
must be multiplied by the appropriate
correction factors below to obtain
modified ratings that must equal or
exceed the application requirements.
Section 5 of ANSI C37 provides

further guidance for medium voltage
breaker application.
Reclosing Duty
ANSI Standard C37.010 indicates the
reduction factors to use when circuit
breakers are used as reclosers. Eaton
VCP-W breakers are listed at 100%
rating factor for reclosing.
Note: Intermediate values may be obtained

by interpolation.
b.
V max
See Table 6.0-1, Tab 6.

Where:
I
= Rated short-circuit current
Vmax = Rated maximum voltage
of the breaker
VD
KI
Operating Voltage
kV
Motor Load
2.4
100%
= Actual system voltage

= Maximum symmetrical
interrupting capacity
c. E/X x 1.6 m rms closing and

latching capability of the breaker
and/or
E/X x 2.7 m Crest closing and
latching capability of the breaker.
Altitude in
Feet (Meters)
Correction Factor
Current
Voltage
3300 (1006) (and below)

5000 (1524)
10,000 (3048)
1.00
0.99
0.96
1.00
0.95
0.80
4.16
1.5
2
2.5
2.5
3
3
3.75
3.75
5
5
7.5
7.5
10 1
10
10
10
12 1
12
15
15
20
20 1
20
25
30
3
4
5
6
7
8
12
13.8
11
50 VCP-W 250
12 kA
50 VCP-W 250
36 kA
50 VCP-W 350
49 kA
50 VCP-W 250
10.1 kA
150 VCP-W 500

23 kA
150 VCP-W 500

22.5 kA
150 VCP-W 500

19.6 kA
12
13
50 VCP-W 250
33.2 kA
14
50 VCP-W 350
46.9 kA
75 VCP-W 500
41.3 kA
Breaker Type and

symmetrical interrupting capacity
at the operating voltage
50 1
1
10
6.6
0%
1
1.5
2
Table 1.3-4. Application Quick Check Table

Source
Transformer
MVA Rating
ii
Table 1.3-3. Altitude Derating
a. Maximum voltage rating exceeds

the operating voltage of the system:
E
-------- I ----------------- KI
X2
Vo
15
150 VCP-W 750
35 kA
150 VCP-W 750

30.4 kA
16
150 VCP-W 1000

46.3 kA
150 VCP-W 1000

40.2 kA
17
Transformer impedance 6.5% or more, all other transformer impedances are 5.5% or more.
18
19
20
21
CA08104001E
1.3-8

System Analysis
April 2016
Sheet 01 040
i
ii
1
2
Application on Symmetrical Current Rating Basis
For Three-Phase Fault
Example 1Fault Calculations
E
I 3-Phase ----X
Given a circuit breaker interrupting and momentary rating in the table below,
verify the adequacy of the ratings for a system without motor loads, as shown.
Table 1.3-5. Short-Circuit Duty
Type
Breaker
V Max.
50VCPW250
4.76 kV
Three-Phase Symmetrical Interrupting Capability

at V Max.
Max. KI
at 4.16 kV Oper. Voltage
4.76
----------- (29) = 33.2 kA I1
4.16
LG symmetrical interrupting capability
29 kA
36 kA
36 kA
Close and Latch or

Momentary
58 kA I3
4
5
Check capabilities I1, I2 and I3 on the following utility system where there is no
motor contribution to short circuit.
7
8
On 13.8 kV System, 3.75 MVA Base

13.8 kV
X
3.75 MVA- = 0.01 pu or 1%

Z = -------------------------------375 MVA
= 15
2
2
2
2X
Z = X + R = R -------+ 1
2
R
375 MVA
Available
9
10
X = X
----- R = 15 (0.066) = .99%
R
11
13
1
1
------------------ 0.066%
15.03
266
----------------
13.8 kV
3750 kVA
12
----------------------2
X
-------- + 1
2
Transformer Standard 5.5% Impedance

has a 7.5% Manufacturing Tolerance
4.16 kV
5.50 Standard Impedance

0.41 (7.5% Tolerance)
Transformer Z =
5.09%
50VPC-W250
IB
I 3-Phase -----X
where X is per unit reactance
IB is base current
1.15 (33.2) = 38.2 kA I2
Note: Interrupting capabilities I1 and I2 at operating voltage must not exceed maximum
symmetrical interrupting capability Kl.
where X is ohms per phase and E is

the highest typical line-to-neutral
operating voltage or
MVA
Base current I B = 3.75
= 0.52kA
3 4.16 kV
I1
0.52
I 3-Phase ----- ---------------------- 8.6 kA Sym.
0.0604
X
System X
9 (is less than 15)
R
would use 1.0 multiplying factor for
short-circuit duty, therefore, shortcircuit duty is 8.6 kA sym. for threephase fault I1 and momentary duty is
8.6 x 1.6 = 13.7 kA I3.
For Line-to-Ground Fault

3I B
3E
I LG ---------------------------- ---------------------------2X 1 + X 0 2X 1 + X 0
For this system, X0 is the zero sequence
reactance of the transformer, which
is equal to the transformer positive
sequence reactance and X1 is the positive sequence reactance of the system.
Therefore,
3(0.52)
I LG 9.1 kA Sym.
2(0.0604) + 0.0505
Using 1.0 multiplying factor (see
Table 1.3-6), short-circuit duty = 9.1 kA
Sym. LG (I2)
14
Answer
15
Figure 1.3-6. Example 1One-Line Diagram
16
From transformer losses per unit or

percent R is calculated
17
18
19
20
21
The 50VCP-W250 breaker capabilities

exceed the duty requirements and
may be applied.
31,000 Watts Full Load

6,800 Watts No Load
24,200 Watts Load Losses
Transformer X =
Z R
24.2 kW
R -------------------------------- 0.0065 pu or 0.65%
3750 kVA
2
(5.09) (0.65) =
25.91 0.42 =
25.48
X = 5.05%
X
13.8 kV System 0.99%
Transformer
5.05%
System Total 6.04%
or
0.0604 pu
With this application, shortcuts could

have been taken for a quicker check of
the application. If we assume unlimited
short circuit available at 13.8 kV and
that Trans. Z = X
I B 0.52
Then I 3-Phase ------ ------------------ 9.5 kA Sym.
X 0.055
X/R ratio 15 or less multiplying factor
is 1.0 for short-circuit duty.
R
X/R
0.066% 15
0.65%
8
0.716% 9
0.00716 pu
The short-circuit duty is then 9.5 kA

Sym. (I1, I2) and momentary duty is
9.5 x 1.6 kA = 15.2 kA (I3).
CA08104001E

System Analysis
April 2016
1.3-9
Sheet 01 041
7500 kVA
7.5 MVA- = 0.628 kA

Base Current IB = -----------------------------3 6.9 kV
R
X/R
X = 0.628 (6.9) = 0.015 0.015

21 (13.8)
0.001
15
Transformer
0.0055
10
X = 15
R
21 kA Sym. Available
13.8 kV
All calculations on per unit basis.

7.5 MVA base
13.8 kV System
Given the system shown with motor

loads, calculate the fault currents
and determine proper circuit breaker
selection.
Z = 5.53%
X = 5.5%
R = 0.55%
ii
X
= 10
R
6.9 kV
13.8 kV System
0.055
X
= 25
R
197A FL
X''d = 20%
Total Source Transformer 0.070 pu 0.0065 pu 11
X
= 35
R
173A FL
X''d = 25%
3000 hp Synchronous Motor

X = 0.20 (0.628) = 0.638 pu at 7.5 MVA Base
0.197
3000 hp
1.0 PF
Syn.
4
5
6
2500 hp
Ind.
2500 hp Ind. Motor

X = 0.25 (0.628) = 0.908 pu at 7.5 MVA Base
0.173
E I BI 3-Ph ----- ----where X on per unit base
X X
Table 1.3-6. Multiplying Factor for E/X
Amperes (ANSI C37.010, 1979, Figures 1.1-8,
1.1-9 and 1.1-10)
System
X/R
Type VCP-W Vacuum

Circuit Breaker
Rated Interrupting Time, 5-Cycle
7
Source of
Short-Circuit Current
Interrupting
E/X Amperes
Momentary
E/X Amperes
X
R
X (1)
R (X)
1
R
I3 Source Transformer
0.628
0.070
= 8.971
0.628
= 8.971
0.070
11
11
0.070
= 157
I1 3000 hp Syn. Motor
0.628
= 0.656
(1.5) 0.638
0.628
= 0.984
0.638
25
25
0.638
= 39
I1 2500 hp Syn. Motor
0.628
= 0.461
(1.5) 0.908
0.628
= 0.691
0.908
35
35
0.908
= 39
I3F =
Type of Fault
Ratio
ThreePhase
LG
Three-Phase
and LG
Source of Short Circuit

Local
Remote
X
System ----- = 0.062 (235) = 14.5 is a Multiplying Factor of 1.0 from Table 1.3-6
R
1.00
1.00
1.00
1.00
1.04
1.00
1.00
1.02
1.06
1.10
1.00
1.00
1.05
1.10
1.13
36
40
45
50
55
1.06
1.08
1.12
1.13
1.14
1.14
1.16
1.19
1.22
1.25
1.17
1.22
1.25
1.27
1.30
Breaker
Type
60
65
70
75
80
1.16
1.17
1.19
1.20
1.21
1.26
1.28
1.29
1.30
1.31
1.32
1.33
1.35
1.36
1.37
150VCP-W500
85
90
95
100
1.22
1.23
1.32
1.33
1.38
1.39
1.40
1.41
100
120
130
1.24
1.24
1.24
1.34
1.35
1.35
1.42
1.43
1.43
75VCP-W500

at V Max.
8.25 kV 33 kA
15 kV
18 kA
10
11
13
14
Table 1.3-7. Short-Circuit Duty = 10.1 kA

V
Max.
12
I B = 0.628 = 0.062
Total X = ------------------------10.1
I 3F
1
15 1
20
25
30
10.647
Total 1/R = 235
x 1.6
17.0 kA Momentary Duty
10.088
10.1 kA
or
Max. KI
41 kA
23 kA
Answer
Either breaker could be properly
applied, but price will make the type
150VCP-W500 the more economical
selection.

8.25
6.9
Close and Latch

or Momentary
(33) = 39.5 kA
66 kA
15 (18) (39.1) = 23 kA
6.9
(But not to exceed KI)
37 kA
15
16
17
18
19
20
Where system X/R ratio is 15 or less, the

multiplying factor is 1.0.
21
CA08104001E

System Analysis
April 2016
Sheet 01 042
i
ii
Answer
Check breaker application or generator bus for the system of generators shown.
Each generator is 7.5 MVA, 4.16 kV 1040 A full load, IB = 1.04 kA
Sub transient reactance Xd = 11% or, X = 0.11 pu
Gen X
----- ratio is 30
R
1
1 1 1 3
1 1 1 3
1
and
RS R R R R
X X X X
XS
3
4
5
6
7
The 50VCP-W250 breaker could be

applied.
XXS
R
or XS X
Gen X
----- and R S ---- Therefore, System --------- -------- 30
R
R
3
3
RS
G1
G2
G3
Since generator neutral grounding reactors are used to limit the ILG to I3-phase or
below, we need only check the I3 short-circuit duty.
I B I B I B 31B 3(1.04)
IB Phase ----- + ------ + ------ + ------------ ----------------------- 28.4 kA Symmetrical E/X amperes
0.11
X X X X
4.16 kV
X
System ----- of 30 is a Multiplying Factor of 1.04 from Table 1.3-6.
R
Short-circuit duty is 28.4 (1.04) = 29.5 kA Symmetrical
8
9

Breaker Type
V Max.
at V Max.
Max. KI
50VCP-W250
4.76 kV
29 kA
36 kA
4.76
(29) = 33.2 kA
4.16
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E
April 2016

System Analysis
1.3-11
Sheet 01 043
Medium Voltage Fuses

Fault Calculations
There are two basic types of medium
voltage fuses. The following definitions
are taken from ANSI Standard C37.40.
Expulsion Fuse (Unit)

A vented fuse (unit) in which the
expulsion effect of the gases produced
by internal arcing, either alone or aided
by other mechanisms, results in current
interruption.
Current-Limiting Fuse (Unit)

A fuse unit that, when its currentresponsive element is melted by a
current within the fuses specified
current-limiting range, abruptly
introduces a high resistance to
reduce current magnitude and
duration, resulting in subsequent
current interruption.
There are two classes of fuses;
power and distribution. They are
distinguished from each other by
the current ratings and minimum
melting type characteristics.
The current-limiting ability of a
current-limiting fuse is specified by
its threshold ratio, peak let-through
current and I2t characteristics.
Interrupting Ratings of Fuses

Modern fuses are rated in amperes
rms symmetrical. They also have a
listed asymmetrical rms rating that
is 1.6 x the symmetrical rating.
Refer to ANSI/IEEE C37.48 for fuse
interrupting duty guidelines.
Calculation of the Fuse Required

Interrupting Rating:
Step 1Convert the fault from
the utility to percent or per unit on
a convenient voltage and kVA base.
Step 2Collect the X and R data of all
the other circuit elements and convert
to a percent or per unit on a convenient kVA and voltage base same as
that used in Step 1. Use the substransient X and R for all generators and
motors.
CA08104001E
Step 3Construct the sequence

networks using reactances and connect
properly for the type of fault under
consideration and reduce to a single
equivalent reactance.
Step 4Construct the sequence
networks using resistances and
connect properly for the type of
fault under consideration and reduce
to a single equivalent resistance.
Step 5Calculate the E/XI value,
where E is the prefault value of the
voltage at the point of fault normally
assumed 1.0 in pu. For three-phase
faults E/XI is the fault current to be
used in determining the required
interrupting capability of the fuse.
Note: It is not necessary to calculate a
single phase-to-phase fault current. This
current is very nearly 3 /2 x three-phase
fault. The line-to-ground fault may exceed
the three-phase fault for fuses located in
generating stations with solidly grounded
neutral generators, or in delta-wye transformers with the wye solidly grounded,
where the sum of the positive and negative
sequence impedances on the high voltage
side (delta) is smaller than the impedance of
the transformer.
For single line-to-ground fault:

X I X I (+) + X I () + X I (0)
E
If ------- 3
XI
Step 6Select a fuse whose
published interrupting rating
exceeds the calculated fault current.
Figure 1.3-2 should be used where
older fuses asymmetrically rated are
involved.
The voltage rating of power fuses used
on three-phase systems should equal
or exceed the maximum line-to-line
voltage rating of the system. Current
limiting fuses for three-phase systems
should be so applied that the fuse
voltage rating is equal to or less than
1.41 x nominal system voltage.
Low Voltage Power Circuit

BreakersFault Calculations
The steps for calculating the fault current for the selection of a low voltage
power circuit breaker are the same as
those used for medium voltage circuit
breakers except that where the connected loads to the low voltage bus
includes induction and synchronous
motor loads. The assumption is made
that in 208Y/120 V systems the contribution from motors is two times the full
load current of step-down transformer.
This corresponds to an assumed 50%
motor aggregate impedance on a kVA
base equal to the transformer kVA
rating or 50% motor load. For 480 V,
480Y/277 V and 600 V systems, the
assumption is made that the contribution
from the motors is four times the full
load current of the step-down transformer, which corresponds to an assumed
25% aggregate motor impedance on a
kVA base equal to the transformer kVA
rating or 100% motor load.
In low voltage systems that contain
generators, the subtransient reactance
should be used.
If the X/R to the point of fault is greater
than 6.6, a derating multiplying factor
(MF) must be applied. The X/R ratio is
calculated in the same manner as that
for medium voltage circuit breakers.
ii
1
2
3
4
5
6
7
8
9
10
Calculated symmetrical amperes x

MF breaker interrupting rating.
11
The multiplying factor MF can be

calculated by the formula:
12
X/R
2 1 2.718
MF
2.29
13
If the X/R of system feeding the

breaker is not known, use X/R = 15.
14
For fused breakers by the formula:
15
2 X/R
1 2 2.718
MF
1.25
If the X/R of the system feeding the

breaker is not known, use X/R = 20.
Refer to Table 1.3-8 for the standard
ranges of X/R and power factors used in
testing and rating low voltage breakers.
Refer to Table 1.3-9 for the circuit
breaker interrupting rating multiplying
factors to be used when the calculated
X/R ratio or power factor at the point
the breaker is to be applied in the
power distribution system falls outside
of the Table 1.3-8 X/R or power factors
used in testing and rating the circuit
breakers. MF is always greater than 1.0.
16
17
18
19
20
21

System Analysis
April 2016
Sheet 01 044
i
ii
1
2
3
4
5
6
7
8
Molded-Case Breakers and

Insulated Case Circuit
BreakersFault Calculations
The method of fault calculation is the
same as that for low voltage power
circuit breakers. Again, the calculated
fault current x MF breaker interrupting
capacity. Because molded case breakers
are tested at lower X/R ratios, the MFs
are different than those for low voltage
power circuit breakers.
X
2
R 2
1 + 2.718
MF ----------------------------------------------------X
1
R 1
1 + 2.718
X1 R1 = test X/R value
X2 R2 = X/R at point where breaker
is applied
Low Voltage Circuit Breaker

Interrupting Derating Factors
Refer to Table 1.3-8 for the standard
ranges of X/R and power factors
used in testing and rating low voltage
breakers. Refer to Table 1.3-9 for
the circuit breaker interrupting rating
de-rating factors to be used when the
calculated X/R ratio or power factor
at the point the breaker is to be applied
in the power distribution system falls
outside of the Table 1.3-8 X/R or power
factors used in testing and rating the
circuit breakers.
Normally the short-circuit power factor
or X/R ratio of a distribution system
need not be considered in applying
low voltage circuit breakers. This is
because the ratings established in
the applicable standard are based
on power factor values that amply
cover most applications.
11
12
13
Table 1.3-8. Standard Test Power Factors

Interrupting
Rating in kA
Power Factor
Test Range
X/R Test
Range
Molded Case Circuit Breaker

10 or Less
Over 10 to 20
Over 20
0.450.50
0.250.030
0.150.20
1.981.73
3.873.18
6.64.9
Low Voltage Power Circuit Breaker

All
0.15 Maximum 6.6 Minimum
For distribution systems where the

calculated short-circuit current X/R
ratio differs from the standard values
given in the above table, circuit breaker
interrupting rating derating factors from
Table 1.3-9 table should be applied.
Table 1.3-9. Circuit Breaker Interrupting Rating Derating Factors

% P.F.
X/R
Interrupting Rating
Molded Case or Insulated Case
9
10
Established standard values include

the following:
Power Circuit Breaker
m/ = 10 kA
>10 kA
m/ = 20 kA
L20 kA
Unfused
Fused
50
30
25
1.73
3.18
3.87
1.000
0.847
0.805
1.000
1.000
0.950
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
1.000
20
15
12
4.90
6.59
8.27
0.762
0.718
0.691
0.899
0.847
0.815
1.000
0.942
0.907
1.000
1.000
0.962
1.000
0.939
0.898
10
8.5
7
9.95
11.72
14.25
0.673
0.659
0.645
0.794
0.778
0.761
0.883
0.865
0.847
0.937
0.918
0.899
0.870
0.849
0.827
19.97
0.627
0.740
0.823
0.874
0.797
Note: These are derating factors applied to the breaker and are the inverse of MF.
14
15
16
17
18
19
20
21
CA08104001E

System Analysis
April 2016
1.3-13
Sheet 01 045
Short-Circuit CalculationsShortcut Method
Determination of Short-Circuit Current

Note 1: Transformer impedance generally relates to self-ventilated rating (e.g., with OA/FA/FOA transformer use OA base).
Note 2: kV refers to line-to-line voltage in kilovolts.
Note 3: Z refers to line-to-neutral impedance of system to fault where R + jX = Z.
Note 4: When totaling the components of system Z, arithmetic combining of impedances as ohms Z. per unit Z. etc., is considered a
shortcut or approximate method; proper combining of impedances (e.g., source, cables transformers, conductors, etc.). should use
individual R and X components. This Total Z = Total R + j Total X (see IEEE Red Book Standard No. 141).
Select convenient kVA base for system to
be studied.
2.
Change per unit, or percent, impedance from

one kVA base to another:
(a) Per unit = pu impedance kVA base 2 =

(b) Percent = % impedance kVA base 2 =
kVA base 2
kVA base 1
kVA base 2
kVA base 1
(pu impedance on kVA base 1)
Change power-source impedance to per unit

or percent impedance on kVA base as selected
for this study:
(% impedance)
(10)
kVA base
6
7
kVA base in study

Per-unit impedance = pu Z = -----------------------------------------------------------------------------------------power-source kVA fault capacity
8
9
(a) motor kVA 3 (kV) (I) where I = motor nameplate full-load amperes
Change motor rating to kVA:
10
(b) if 1.0 power factor synchronous motorkVA = (0.8) (hp)

(c) if 0.8 power factor synchronous motorkVA = (1.0) (hp)
(d) if induction motor
(a) Base current = I Base =
Determine symmetrical short-circuit current:
kVA = (1.0) (hp)

Three-phase kVA
11
Single-phase kVA
kV line-to-neutral
or
3 kV
12
(b) Per unit I SC = 1.0
pu Z
(c) rms Symmetrical current = ISC = (pu ISC) (IBase Amperes)
13
Three-phase KVA base

Single-phase kVA base
(d) rms Symmetrical current = Amperes = ---------------------------------------------------------------- or ---------------------------------------------------------------- pu Z kV
pu Z 3 kV
7.
Determine symmetrical short-circuit kVA:
8.
Determine line-to-line short-circuit current:
(a) if utility fault capacity given in kVA
kVA base in study

Per-unit impedance = pu Z = --------------------------------------------------------------------------------------------------------------(short-circuit current) 3 (kV of source)
6.
kV 2
(b) if utility fault capacity given in rms symmetrical short circuit amperes
5.
(% impedance on kVA base 1)
impedance) (kVA base)

percent impedance = (ohms
(a) Per unit impedance = pu Z =
2
kV
1000
100
(ohms impedance) (kVA base)
(b) % impedance = % Z =

10
kV 2
Change ohms, or percent or per unit, etc.:
(c) Ohms impedance =
4.
1
2
1.
3.
ii
(e)
(Three-phase kVA base) (100)

Single-phase kVA base (100)
= ----------------------------------------------------------------------------------- or -------------------------------------------------------------------------------(%Z) kV
(%Z) 3 kV
(g)
(kV) (1000)
= ----------------------------------3 (ohms Z)
14
15
(kVA base) (100)- = kV 2 1000

base- = --------------------------------------------(a) Symmetrical short-circuit kVA = kVA
--------------------------------------------------------- pu Z
%Z
ohms Z
2
3(line-to-neutral kV) 1000
(b)
= -----------------------------------------------------------------------------(ohms Z)
16
17
(a) from three-phase transformerapprox. 86% of three-phase current

(b) three single-phase transformers (e.g., 75 kVA, Z = 2%) calculate same as one three-phase
unit (i.e., 3 x 75 kVA = 225 kVA, Z = 2%).
18
(c) from single-phase transformersee Page 1.3-15.
9.
Determine motor contribution (or feedback) as

source of fault current:
(a) synchronous motor5 times motor full load current (impedance 20%)
(b) induction motor4 times motor full-load current (impedance 25%)
See IEEE
Standard No. 141
(c) motor loads not individually identified, use contribution from group of motors as follows:
on 208Y/120 V systems2.0 times transformer full-load current
on 240-480-600 V three-phase, three-wire systems4.0 times transformer full-load current
on 480Y/277 V three-phase, four-wire systems
In commercial buildings, 2.0 times transformers full-load current (50% motor load)
In industrial plants, 4.0 times transformer full-load current (100% motor load)
CA08104001E
19
20
21

System Analysis
April 2016
Sheet 01 046
Example Number 1
How to Calculate Short-Circuit Currents at Ends of Conductors
ii
A. System Diagram
B. Impedance Diagram (Using Short Cut Method for Combining Impedances

and Sources).
A
Utility Source
500 MVA
Major Contribution
Utility
2
Cables
Transformer
Switchboard Fault
1000 kV A
5.75%
480V
Cables
4
5
6
7
Fault
Cable
Switchboard Fault
100 ft (30m)
3350 kcmil Cable
in Steel Conduit
0.002 pu
1.00 pu
1.00 pu
1.00 pu
0.0575 pu
0.027 pu
Switchboard Fault
0.027 pu
0.027 pu
Mixed LoadMotors and Lighting

Each Feeder100 ft (30m) of 3350 kcmil
Cable in Steel Conduit Feeding Lighting and
250 kVA of Motors
0.027 pu
Cable Fault
Cable Fault
Combining Series Impedances: ZTOTAL = Z1 + Z2 + ... +Zn
9
10
11
12
13
C. Conductor impedance from Table 1.5-17,

Page 1.5-15. Conductors: 3350 kcmil copper,
single conductors Circuit length: 100 ft
(30 m), in steel (magnetic) conduit Impedance
Z = 0.00619 ohms/100 ft (30 m).
ZTOT = 0.00619 ohms (100 circuit feet)
Combining Parallel Impedances:
1 =
ZTOTAL
0.0595 pu
1 + 1 + ... 1
Z1
Z2
Zn
0.342 pu
E
0.027 pu
D. Fault current calculations (combining impedances arithmetically, using approximate

Short Cut methodsee Note 4,
Page 1.3-13)
Step
1
Equation
(See)
4(a)
kVA base - = -------------------1000 - = 0.002 pu

Utility per unit impedance = Z = -----------------------------------------pu
utility fault kVA 500.000
3(a)
Transformer per unit impedance = Z
16
4(a) and
9(c)
kVA base - = ------------------1000 - = 1.00 pu

Motor contribution per unit impedance = Z = --------------------------------------pu
4 x motor kVA 4 x 250
17
3(a)
Cable impedance in ohms (see above) = 0.00619 ohms
14
15
Cable impedance per unit =
6(d)
19
20
21
0.0777 pu
0.027 pu
Calculation
Select 1000 kVA as most convenient base, since all data except utility source is on
secondary of 1000 kVA transformer.
18
6
0.0507 pu
pu
pu
%Z- = 5.75
= ------------------- = 0.0575 pu
100
100
base)
(0.00619)(1000)- = 0.027 pu
= (ohms)(kVA
-------------------------------------------------- = -----------------------------------------2
2
(kV) (1000)
(0.480) (1000)
Total impedance to switchboard fault = 0.0507 pu (see diagram above)

kVA base
1000
Symmetrical short circuit current at switchboard fault = 3-phase
= = 23,720 amperes rms
Z 3 kV
0.0507 3 0.480
pu
6(d)
Total impedance to cable fault = 0.0777 pu (see diagram above)

kVA base
1000
Symmetrical short circuit current at cable fault = 3-phase
= = 15, 480 amperes rms
Z 3 kV
0.0777 3 0.480
pu
Figure 1.3-9. Example Number 1

CA08104001E

System Analysis
April 2016
1.3-15
Sheet 01 047
Example Number 2
Fault CalculationSecondary Side of Single-Phase Transformer

A. System Diagram
480V Three-Phase Switchboard Bus at 50,000A Symmetrical, X/R = 6.6
Z
{ RX == 0.1498
0.9887 Z
R
Z=
100 Ft. Two #2/0 Copper Conductors, Magnetic Conduit R = 0.0104 Ohms
X = 0.0051 Ohms
R=
75 kVA Single-Phase 480-120/240V; Z = 2.8%, R = 1.64%, X = 2.27%
6.6
X = 6.6 R
120V
F2
Half-winding of Transformer
1
2
6.6R + R = 43.56R + R =
X +R =
44.56R = 6.6753R
Z
6.6753
R = 0.1498Z
X = 6.6R
240V
F1
ii
Deriving Transformer R and X:
X = 0.9887Z
% R by 1.5
{ Multiply
Multiply % X by 1.2 } Reference: IEEE Standard No. 141
Full-winding of Transformer
B. Impedance DiagramFault F1
RSyst = 0.00054
RSyst = 0.00356
RSyst = 0.00054
XSyst = 0.00356
RCond = 0.00677
RCond = 0.00332
RCond = 0.00677
XCond = 0.00332
RTfmr = 0.0164
RTfmr = 0.0227
RTfmr = 0.0246
XTfmr = 0.0272
RTotal = 0.02371
F1
RTotal = 0.02958
F1
C. Impedance DiagramFault F2
RTotal = 0.03191
F2
6
7
XTotal = 0.03408
F2
D. Impedance and Fault Current Calculations75 kVA Base

Note: To account for the outgoing and return paths of single-phase circuits (conductors,
systems, etc.) use twice the three-phase values of R and X.
ZSyst
75
0.0018 pu
3 0.480 50,000
kVA Base
ZCond =
2
kV 1000
ohms
(From Page 1.3-13

Formula 4(b) )
(From Page 1.3-13

Formula 3(a) )
Full-winding of Transformer (75 kVA Base)
RSyst = 2 (0.1498 x Z)
= 0.00054 pu
XSyst = 2 (0.9887 x Z)
0.0104 75
RCond = 2
0.48 2 1000
0.0051 75
XCond = 2
0.48 2 1000
1.64
RTfmr =
100
= 0.00356 pu
XTfmr =
= 0.00677 pu
11
= 0.00332 pu
= 0.0164 pu
2.27
100
= 0.0277 pu
1.64
RTfmr = 1.5
100
Half-winding of Transformer (75 kVA Base)
XTfmr = 1.2
Impedance to Fault F1Full Winding
Impedance to Fault F2Half Winding
Short circuit current F1 = 75 (0.03791 x 0.240 kV) = 8,243 A Symmetrical
Short circuit current F2 = 75 (0.04669 x 0.120 kV) = 13,386 A Symmetrical
= 0.0272 pu
= 0.03791 pu
= 0.04669 pu
Z=
0.02371 + 0.02958
Z=
0.03191 + 0.03408
at the load side end of the conductors

can be calculated as follows.
Add source and conductor impedance or

0.00923 + 0.00273 = 0.01196 total ohms
This method uses the approximation

of adding Zs instead of the accurate
method of Rs and Xs.
277 V/30,000 A = 0.00923 ohms

(source impedance)
Next, 277 V/0.01196 ohms = 23,160 A

rms at load side of conductors
CA08104001E
15
16
Method 1: Shortcut Methods

End of Cable
0.00551/2 = 0.00273 ohms (conductor

impedance)
13
14
2.27
100
Conductor ohms for 500 kcmil conductor from reference data in this section
in magnetic conduit is 0.00551 ohms
per 100 ft (30 m). For 100 ft (30 m) and
two conductors per phase we have:
12
= 0.0246 pu
Figure 1.3-10. Example Number 2
For Example: For a 480/277 V system

with 30,000 A symmetrical available
at the line side of a conductor run of
100 ft (30 m) of 2500 kcmil per phase
and neutral, the approximate fault current
10
17
18
30,000 A available
19
100 ft (30 m)
2500 kcmil per phase
20
If = 23,160 A
Figure 1.3-11. Short-Circuit Diagram
21

System Analysis
April 2016
Sheet 01 048
ii
1
2
3
4
5
6
Method 2: Chart Approximate Method
Step Five
The chart method is based on the following:
Enter the chart along the bottom horizontal scale with the
distance (in feet) from the transformer to the fault point.
Draw a vertical line up the chart to the point where it intersects the selected curve. Then draw a horizontal line to the
left from this point to the scale along the left side of the chart.
Motor Contribution
For system voltages of 120/208 V, it is reasonable to assume
that the connected load consists of 50% motor load, and that
the motors will contribute four times their full load current
into a fault. For system voltages of 240 and 480 V, it is reasonable to assume that the connected load consists of 100%
motor load, and that the motors will contribute four times
their full load current into a fault. These motor contributions
have been factored into each curve as if all motors were
connected to the transformer terminals.
Feeder Conductors
The conductor sizes most commonly used for feeders
from molded case circuit breakers are shown. For conductor
sizes not shown, the following table has been included for
conversion to equivalent arrangements. In some cases it
may be necessary to interpolate for unusual feeder ratings.
Table 1.3-10 is based on using copper conductor.
Table 1.3-10. Conductor Conversion (Based on Using Copper Conductor)
If Your Conductor is:
Use Equivalent Arrangement
3No. 4/0 cables

4No. 2/0 cables
2500 kcmil
2500 kcmil
32000 kcmil cables

5400 kcmil cables
6300 kcmil cables
4750 kcmil
4750 kcmil
4750 kcmil
800 A busway
1000 A busway
1600 A busway
2500 kcmil
2500 kcmil
4750 kcmil
10
11
12
Short-Circuit Current Readout

The readout obtained from the charts is the rms symmetrical
amperes available at the given distance from the transformer. The circuit breaker should have an interrupting
capacity at least as large as this value.
Step Six
The value obtained from the left-hand vertical scale is the fault
current (in thousands of amperes) available at the fault point.
For a more exact determination, see the formula method.
It should be noted that even the most exact methods for
calculating fault energy use some approximations and some
assumptions. Therefore, it is appropriate to select a method
which is sufficiently accurate for the purpose, but not more
burdensome than is justified. The charts that follow make
use of simplifications that are reasonable under most circumstances and will almost certainly yield answers that are
on the safe side. This may, in some cases, lead to application
of circuit breakers having interrupting ratings higher than
necessary, but should eliminate the possibility of applying
units which will not be safe for the possible fault duty.
Fault Current in Thousands of Amperes (Sym.)
How to Use the Short-Circuit Charts

Step One
14
15
17
18
19
20
21
F
12.5
10.0
1.
2.
3.
4.
System voltage
Transformer kVA rating (from transformer nameplate)
Transformer impedance (from transformer nameplate)
Primary source fault energy available in kVA
(from electric utility or distribution system engineers)
Select the applicable chart from the following pages. The

charts are grouped by secondary system voltage, which is
listed with each transformer. Within each group, the chart
for the lowest kVA transformer is shown first, followed in
ascending order to the highest rated transformer.
Step Three
Select the family of curves that is closest to the available
source kVA. The black line family of curves is for a source of
500,000 kVA. The lower value line (in red) family of curves is
for a source of 50,000 kVA. You may interpolate between
curves if necessary, but for values above 100,000 kVA it is
appropriate to use the 500,000 kVA curves.
Step Four
Select the specific curve for the conductor size being used. If
your conductor size is something other than the sizes shown
on the chart, refer to the conductor conversion Table 1.3-10.
UTILITY KVA
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
7.5
5.0
2.5
Step Two
16
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
Obtain the following data:
5
10
20
50
100
200
500 1000 2000
Distance in Feet from T ransformer to Breaker Location
5000
Figure 1.3-12. 225 kVA Transformer/4.5% Impedance/208 V
UTILITY KV
13
15.0
30
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
25
20
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
B
F
15
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
10
5
10
20
50
100
200
500 1000 2000
5000
CA08104001E

System Analysis
April 2016
1.3-17
Sheet 01 049
30
F
25
i
UTILITY KV
A
B
C
D
E
F
UTILITY KVA
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
INFINITE
500,000
250,0 0 0
150,0 0 0
10 0,0 0 0
50,000
20
15
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
10
120
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
100
80
60
40
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
ii
1
2
3
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
20
4
0
5
10
20
50
100
200
500 1000 2000
5000
5
10
20
50
100
200
500 1000 2000
5000
6
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
50
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
40
F
30
20
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
10
5
10
20
50
100
200
500 1000 2000
UTILITY KVA
UTILITY KVA
60
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
B
100
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
80
F
60
10
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
40
20
5000
120
11
5
10
20
50
100
200
500 1000 2000
5000
12
13
60
B
50
UTILITY KVA
UTILITY KVA
14
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
40
30
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
20
10
5
10
20
50
100
200
500 1000 2000
5000
12
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
10
B
15
16
F
8
18
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
17
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
5
10
20
50
100
200
500 1000 2000
19
5000
20
21
CA08104001E

System Analysis
April 2016
Sheet 01 050
1
2
3
UTILITY KVA
ii
UTILITY KVA
30
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
25
20
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
15
F
10
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
4
0
5
10
20
50
100
200
500 1000 2000
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
50
40
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
30
20
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
10
5000
60
5
10
20
50
100
200
500 1000 2000
5000
9
10
11
12
13
30
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
25
20
UTILITY KVA
UTILITY KVA
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
B
F
15
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
10
5
10
20
50
100
200
500 1000 2000
5000
60
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
50
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
40
F
30
20
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
10
5
10
20
50
100
200
500 1000 2000
5000
15
16
17
18
14
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
30
B
25
UTILITY KVA
A INFINITE
B 500,000
C 250,000
D 150,000
E 100,000
F
50,000
20
15
4 750 kcmil
2 500 kcmil
250 kcmil
#1/0 AWG
#4 AWG
10
19
0
20
5
10
20
50
100
200
500 1000 2000
5000
21
CA08104001E

System Analysis
April 2016
1.3-19
Sheet 01 051
Determining X and R Values

from Transformer Loss Data
Method 1:
Given a 500 kVA, 5.5% Z transformer
with 9000W total loss; 1700W no-load
loss; 7300W load loss and primary
voltage of 480 V.
How to Estimate Short-Circuit

Currents at Transformer
Secondaries:
Method 1:
To obtain three-phase rms symmetrical
short-circuit current available at
transformer secondary terminals,
use the formula:
100
I SC = I FLC -----------%Z
500
3 R = 7300 W
3 0.480
%R = 0.0067 ohms
0.0067 500
%R = = 1.46%
2
10 0.48
%X =
5.5 1.46 = 5.30%
Method 2:
Using same values above.
where %Z is the transformer impedance

in percent, from Tables 1.5-6 through
1.5-11, Page 1.5-11.
This is the maximum three-phase symmetrical bolted-fault current, assuming
sustained primary voltage during fault,
i.e., an infinite or unlimited primary
power source (zero source impedance).
Because the power source must
always have some impedance, this
is a conservative value; actual fault
current will be somewhat less.
Note: This will not include motor shortcircuit contribution.
7300
= 1.46
10 500
2
Refer to Page 1.5-9 in the Reference

section, and use appropriate row of
data based on transformer kVA and
primary short-circuit current available.
This will yield more accurate results
and allow for including motor shortcircuit contribution.
i
ii
1
2
3
4
5
6
7
8
9
I R Losses
%R =
10 kVA
%X =
Method 2:
10
2
5.5 1.46 = 5.30%
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

System Analysis
April 2016
Sheet 01 052
i
ii
1
2
3
4
5
6
7
8
9
Voltage Drop Considerations

The first consideration for voltage
drop is that under the steady-state
conditions of normal load, the voltage
at the utilization equipment must be
adequate. Fine-print notes in the NEC
recommend sizing feeders and branch
circuits so that the maximum voltage
drop in either does not exceed 3%,
with the total voltage drop for feeders
and branch circuits not to exceed 5%,
for efficiency of operation. (Fine print
notes in the NEC are not mandatory.)
In addition to steady-state conditions,
voltage drop under transient conditions, with sudden high-current, shorttime loads, must be considered. The
most common loads of this type are
motor inrush currents during starting.
These loads cause a voltage dip on
the system as a result of the voltage
drop in conductors, transformers and
generators under the high current.
This voltage dip can have numerous
adverse effects on equipment in the
system, and equipment and conductors must be designed and sized to
minimize these problems. In many
cases, reduced-voltage starting of
motors to reduce inrush current
will be necessary.
10
Recommended Limits of
Voltage Variation
11
General Illumination: Flicker in

incandescent lighting from voltage
dip can be severe; lumen output drops
about three times as much as the
voltage dips. That is, a 10% drop in
voltage will result in a 30% drop in
light output. While the lumen output
drop in fluorescent lamps is roughly
proportional to voltage drop, if the
voltage dips about 25%, the lamp will
go out momentarily and then restrike.
For high-intensity discharge (HID)
lamps such as mercury vapor, highpressure sodium or metal halide, if the
lamp goes out because of an excessive
voltage dip, it will not restrike until it
has cooled. This will require several
minutes. These lighting flicker effects
can be annoying, and in the case of
HID lamps, sometimes serious. In
areas where close work is being done,
such as drafting rooms, precision
assembly plants, and the like, even
a slight variation, if repeated, can be
very annoying, and reduce efficiency.
Voltage variation in such areas should
be held to 2 or 3% under motor-starting
or other transient conditions.
12
13
14
15
16
17
18
19
20
Computer Equipment: With the

proliferation of data-processing and
computer- or microprocessor-controlled
manufacturing, the sensitivity of
computers to voltage has become an
important consideration. Severe dips of
short duration can cause a computer
to crashshut down completely,
and other voltage transients caused
by starting and stopping motors can
cause data-processing errors. While
voltage drops must be held to a minimum, in many cases computers will
require special power-conditioning
equipment to operate properly.
Industrial Plants: Where large motors
exist, and unit substation transformers
are relatively limited in size, voltage
dips of as much as 20% may be permissible in some cases, if they do not
occur too frequently. Lighting is often
supplied from separate transformers,
and is minimally affected by voltage
dips in the power systems. However, it
is usually best to limit dips to between
5 and 10% at most. One critical consideration is that a large voltage dip can
cause a dropout (opening) of magnetic
motor contactors and control relays.
The actual dropout voltage varies considerably among starters of different
manufacturers. The only standard that
exists is that of NEMA, which states
that a starter must not drop out at 85%
of its nominal coil voltage, allowing
only a 15% dip. While most starters
will tolerate considerably more voltage
dip before dropping out, limiting dip to
15% is the only way to ensure continuity of operation in all cases.
X-Ray Equipment: Medical x-ray and
similar diagnostic equipment, such as
CAT-scanners, are extremely sensitive
to low voltage. They present a small,
steady load to the system until the
instant the x-ray tube is fired. This
presents a brief but extremely high
instantaneous momentary load. In
some modern x-ray equipment, the
firing is repeated rapidly to create
multiple images. The voltage regulation must be maintained within the
manufacturers limits, usually 2 to 3%,
under these momentary loads, to
ensure proper x-ray exposure.
Motor Starting
Motor inrush on starting must be limited
to minimize voltage dips. Table 1.3-11
on the next page will help select the
proper type of motor starter for various
motors, and to select generators of
adequate size to limit voltage dip.
See Tab 29 for additional data on
reduced voltage motor starting.
Utility Systems
Where the power is supplied by a
utility network, the motor inrush can
be assumed to be small compared
to the system capacity, and voltage
at the source can be assumed to
be constant during motor starting.
Voltage dip resulting from motor
starting can be calculated on the basis
of the voltage drop in the conductors
between the power source and
the motor resulting from the inrush
current. Where the utility system is
limited, the utility will often specify the
maximum permissible inrush current
or the maximum hp motor they will
permit to be started across-the-line.
Transformer Considerations
If the power source is a transformer,
and the inrush kVA or current of the
motor being started is small compared
to the full-rated kVA or current of the
transformer, the transformer voltage
dip will be small and may be ignored.
As the motor inrush becomes a significant percentage of the transformer
full-load rating, an estimate of the
transformer voltage drop must be
added to the conductor voltage drop
to obtain the total voltage drop to the
motor. Accurate voltage drop calculation would be complex and depend
upon transformer and conductor
resistance, reactance and impedance,
as well as motor inrush current and
power factor. However, an approximation can be made on the basis of the
low power-factor motor inrush current
(3040%) and impedance of the
transformer.
For example, if a 480 V transformer
has an impedance of 5%, and the
motor inrush current is 25% of the
transformer full-load current (FLC),
then the worst case voltage drop will
be 0.25 x 5%, or 1.25%.
The allowable motor inrush current is
determined by the total permissible
voltage drop in transformer and
conductors.
21
CA08104001E

System Analysis
April 2016
1.3-21
Sheet 01 053
Table 1.3-11. Factors Governing Voltage Drop

Type of
Motor 1
Starting Starting
How
Torque Current 2 Started
Starting
Starting Torque per Unit of
Current
Full Load Torque
% Full-Load 3 Motor Rpm
1750
1150 3
850
Full-Load Amperes
per kVA Generator
Capacity for Each
1% Voltage Drop
i
ii
Design A
Normal
Normal
Across-the-line
resistance
autotransformer
600700
480560
375450
1.5
0.96
0.96
1.35
0.87
0.87
1.25
0.80
0.80
0.0109.00936
0.0136.0117
0.0170.0146
Design B
Normal
Low
Across-the-line
resistance
autotransformer
500600
400480
320400
1.5
0.96
0.96
1.35
0.87
0.87
1.25
0.80
0.80
0.0131.0109
0.0164.01365
0.0205.0170
Design C
High
Low
Across-the-line
resistance
autotransformer
500600
400480
320400
0.2 to 2.5
1.28 to 1.6
1.28 to 1.6
0.0131.0109
0.0164.01365
0.0205.0170
Low
Secondary controller
100% current
for 100%
torque
0.0655
Across-the-line
Across-the-line
Autotransformer
300
450550
288350 4
40% Starting, 40% Pull-In

0.0218
0.0145.0118
0.0228.0197
Wound Rotor
High
Synchronous (for compressors)

Low
Synchronous (for centrifugal pumps) Low
1
2
3
4
Consult NEMA MG-1 sections 1 and 12 for the exact definition of the design letter.
In each case, a solid-state reduced voltage starter can be adjusted and controlled to provide the required inrush current and torque characteristics.
Where accuracy is important, request the code letter of the the motor and starting and breakdown torques from the motor vendor.
Using 80% taps.
Engine Generator Systems

With an engine generator as the
source of power, the type of starter
that will limit the inrush depends on
the characteristics of the generator.
Although automatic voltage regulators
are usually used with all AC enginegenerators, the initial dip in voltage is
caused by the inherent regulation of
the generator and occurs too rapidly
for the voltage regulator to respond.
It will occur whether or not a regulator
is installed. Consequently, the percent
of initial voltage drop depends on the
ratio of the starting kVA taken by the
motor to the generator capacity, the
inherent regulation of the generator,
the power-factor of the load thrown
on the generator, and the percentage
load carried by the generator.
A standard 80% power-factor enginetype generator (which would be
used where power is to be supplied
to motor loads) has an inherent
regulation of approximately 40%
from no-load to full-load. This means
that a 50% variation in load would
cause approximately 20% variation
in voltage (50% x 40% = 20%).
Assume that a 100 kVA, 80% PF
engine-type generator is supplying
the power and that the voltage drop
should not exceed 10%. Can a 7-1/2 hp,
220 V, 1750 rpm, three-phase, squirrelcage motor be started without
exceeding this voltage drop?
Starting ratio =
Percent voltage drop gen. kVA 1000
F.L. amperes volts 3 reg. of gen.
CA08104001E
From the nameplate data on the motor,

the full-load amperes of a 7-1/2 hp.
220 V, 1750 rpm, three-phase, squirrelcage motor is 19.0 A. Therefore:
Starting current (%F.L.) =
10 100 1000
3.45 or 345%.
19.0 220 3 0.40
From Table 1.3-11, a NEMA design C or
NEMA design D motor with an autotransformer starter gives approximately this
starting ratio. It could also be obtained
from a properly set solid-state adjustable reduced voltage starter.
The choice will depend upon the
torque requirements of the load since
the use of an autotransformer starter
reduces the starting torque in direct
proportion to the reduction in starting
current. In other words, a NEMA
design C motor with an autotransformer would have a starting torque
of approximately full-load (see Table
1.3-11) whereas the NEMA design D
motor under the same conditions
would have a starting torque of
approximately 1-1/2 times full-load.
Note: If a resistance starter were used for
the same motor terminal voltage, the starting torque would be the same as that
obtained with autotransformer type, but the
starting current would be higher, as shown.
Shortcut Method
Column 7 in Table 1.3-11 has been
worked out to simplify checking.
The figures were obtained by using the
formula above and assuming
1 kVA generator capacity and 1%
voltage drop.
Example:
Assuming a project having a
1000 kVA generator, where the
voltage variation must not exceed
10%. Can a 75 hp, 1750 rpm, 220 V,
three-phase, squirrel-cage motor be
started without objectionable lamp
flicker (or 10% voltage drop)?
From tables in the circuit protective
devices reference section, the full-load
amperes of this size and type of motor
is 158 A. To convert to same basis as
column 7, 158 A must be divided by
the generator capacity and % voltage
drop, or:
158
= 0.0158 A per kVA
1000 x 10 per 1% voltage drop
Checking against the table, 0.0158 falls
within the 0.01700.0146 range. This
indicates that a general-purpose motor
with autotransformer starting can
be used.
Note: Designers may obtain calculated
information from engine generator
manufacturers.
The calculation results in conservative

results. The engineer should provide
to the engine-generator vendor the
starting kVA of all motors connected to
the generator and their starting sequence.
The engineer should also specify the
maximum allowable drop. The engineer should request that the engine-generator vendor consider the proper
generator size when closed-transition
autotransformer reduced voltage starters, and soft-start solid-state starter
are used; so the most economical
method of installation is obtained.
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21

System Analysis
April 2016
Sheet 01 054
Voltage Drop Formulas
If the receiving end voltage, load current and power factor

(PF) are known.
Approximate Method
ii
E VD = IR cos + IX sin
ER is the receiving end voltage.
where abbreviations are same as below Exact Method.
Exact Methods
2
3
Exact Method 2If receiving or sending mVA and its power

factor are known at a known sending or receiving voltage.
2
Voltage drop
2
2 ZMVA R
E S = E R + --------------------------------- + 2ZMVA R cos R
2
ER
Exact Method 1If sending end voltage and load PF

are known.
or
E VD = E S + IR cos + IX sin E S IX cos IR sin
2
2
2 ZMVA R
- 2ZMVA S cos S
E R = E S + --------------------------------2
ES
where:
5
6
7
8
9
10
E VD = E R cos + I R + E R sin + IX E R
Voltage Drop
EVD = Voltage drop, line-to-neutral, volts

ES
= Source voltage, line-to-neutral, volts
= Line (Load) current, amperes
= Circuit (branch, feeder) resistance, ohms
= Circuit (branch, feeder) reactance, ohms
cos = Power factor of load, decimal

sin = Reactive factor of load, decimal
where:
ER
= Receiving line-line voltage in kV
ES
= Sending line-line voltage in kV
MVAR = Receiving three-phase mVA

MVAS = Sending three-phase mVA
Z
= Impedance between and receiving ends
= The angle of impedance Z
= Receiving end PF
= Sending end PF, positive when lagging
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

System Analysis
April 2016
1.3-23
Sheet 01 055
Voltage Drop
Table 1.3-12. Temperature Correction Factors

for Voltage Drop
Voltage Drop Tables
Conductor
Size
Note: Busway voltage drop tables are

shown in Tab 24 of this catalog.
Tables for calculating voltage drop for

copper and aluminum conductors, in
either magnetic (steel) or nonmagnetic
(aluminum or non-metallic) conduit,
appear on Page 1.3-24. These tables
give voltage drop per ampere per
100 ft (30 m) of circuit length. The
circuit length is from the beginning
point to the end point of the circuit
regardless of the number of conductors.
Tables are based on the following

conditions:
1. Three or four single conductors in
a conduit, random lay. For threeconductor cable, actual voltage
drop will be approximately the
same for small conductor sizes
and high power factors. Actual
voltage drop will be from 10 to
15% lower for larger conductor
sizes and lower power factors.
2.Voltage drops are phase-to-phase,
for three-phase, three-wire or
three-phase, four-wire 60 Hz
circuits. For other circuits, multiply
voltage drop given in the tables by
the following correction factors:
Three-phase, four-wire,
phase-to-neutral
Single-phase, two-wire
Single-phase, three-wire,
phase-to-phase
Single-phase, three-wire,
phase-to-neutral
No. 14 to No. 4
No. 2 to 3/0
4/0 to 500 kcmil
600 to 1000 kcmil
Percent Correction
Power Factors %
100
90
80
70
60
5.0
5.0
5.0
5.0
4.7
4.2
3.1
2.6
4.7
3.7
2.6
2.1
4.6
3.5
2.3
1.5
4.6
3.2
1.9
1.3
Calculations
To calculate voltage drop:
1. Multiply current in amperes by
the length of the circuit in feet to
get ampere-feet. Circuit length is
the distance from the point of
origin to the load end of the circuit.
2. Divide by 100.
3. Multiply by proper voltage drop
value in tables. Result is voltage
drop.
Example:
A 460 V, 100 hp motor, running at 80%
PF, draws 124 A full-load current. It is
fed by three 2/0 copper conductors in
steel conduit. The feeder length is
150 ft (46 m). What is the voltage drop
in the feeder? What is the percentage
voltage drop?
x 1.155
x 0.577
3. Voltage drops are for a conductor

temperature of 75 C. They may be
used for conductor temperatures
between 60 C and 90 C with
reasonable accuracy (within 5%).
However, correction factors in
Table 1.3-12 can be applied if
desired. The values in the table are
in percent of total voltage drop.
1. Determine maximum desired

voltage drop, in volts.
3. Table: 2/0 copper, magnetic conduit,

80% PF = 0.0187
186 x 0.0187 = 3.48 V drop
3.48 x 100 = 0.76% drop
460
4. Conclusion: 0.76% voltage drop
is very acceptable. (See NEC 2005
Article 215, which suggests that a
voltage drop of 3% or less on a
feeder is acceptable.)
2. Divide voltage drop by

(amperes x circuit feet).
ii
3. Multiply by 100.
4. Find nearest lower voltage drop

value in tables, in correct column
for type of conductor, conduit and
power factor. Read conductor size
for that value.
5. Where this results in an oversized

cable, verify cable lug sizes for
molded case breakers and fusible
switches. Where lug size available
is exceeded, go to next higher
rating.
3
4
5
Example:
A three-phase, four-wire lighting
feeder on a 208 V circuit is 250 ft
(76.2 m) long. The load is 175 A at
90% PF. It is desired to use aluminum
conductors in aluminum conduit. What
size conductor is required to limit the
voltage drop to 2% phase-to-phase?
2
1. VD = 208 = 4.16 V
100
2.
4.16
= 0.0000951
175 250
3.
0.0000951 100 = 0.00951
1. 124 A x 150 ft (46 m) = 18,600 A-ft

2. Divided by 100 = 186
x 0.577
x 1.155
To select minimum conductor size:
4. In table, under aluminum conductors, nonmagnetic conduit, 90%

PF, the nearest lower value is
0.0091. Conductor required is
500 kcmil. (Size 4/0 THW would
have adequate ampacity, but the
voltage drop would be excessive.)
6
7
8
9
10
11
12
13
14
15
16
For conductor temperature of 60 C

SUBTRACT the percentage from
Table 1.3-12.
17
For conductor temperature of 90 C

ADD the percentage from Table 1.3-12.
18
19
20
21
CA08104001E

System Analysis
April 2016
Sheet 01 056
i
ii
Table 1.3-13. Voltage DropVolts per Ampere per 100 Feet (30 m); Three-Phase, Phase-to-Phase
Conductor Size
AWG
or kcmil
Magnetic Conduit (Steel)
Nonmagnetic Conduit (Aluminum or Nonmetallic)
Load Power Factor, %
Load Power Factor, %
60
70
80
90
100
60
70
80
90
100
14
12
10
8
0.3390
0.2170
0.1390
0.0905
0.3910
0.2490
0.1590
0.1030
0.4430
0.2810
0.1790
0.1150
0.4940
0.3130
0.1980
0.1260
0.5410
0.3410
0.2150
0.1350
0.3370
0.2150
0.1370
0.0888
0.3900
0.2480
0.1580
0.1010
0.4410
0.2800
0.1780
0.1140
0.4930
0.3120
0.1970
0.1250
0.5410
0.3410
0.2150
0.1350
6
4
2
1
0.0595
0.0399
0.0275
0.0233
0.0670
0.0443
0.0300
0.0251
0.0742
0.0485
0.0323
0.0267
0.0809
0.0522
0.0342
0.0279
0.0850
0.0534
0.0336
0.0267
0.0579
0.0384
0.0260
0.0218
0.0656
0.0430
0.0287
0.0238
0.0730
0.0473
0.0312
0.0256
0.0800
0.0513
0.0333
0.0270
0.0849
0.0533
0.0335
0.0266
1/0
2/0
3/0
4/0
0.0198
0.0171
0.0148
0.0130
0.0211
0.0180
0.0154
0.0134
0.0222
0.0187
0.0158
0.0136
0.0229
0.0190
0.0158
0.0133
0.0213
0.0170
0.0136
0.0109
0.0183
0.0156
0.0134
0.0116
0.0198
0.0167
0.0141
0.0121
0.0211
0.0176
0.0147
0.0124
0.0220
0.0181
0.0149
0.0124
0.0211
0.0169
0.0134
0.0107
250
300
350
500
0.0122
0.0111
0.0104
0.0100
0.0124
0.0112
0.0104
0.0091
0.0124
0.0111
0.0102
0.0087
0.0120
0.0106
0.0096
0.0080
0.0094
0.0080
0.0069
0.0053
0.0107
0.0097
0.0090
0.0078
0.0111
0.0099
0.0091
0.0077
0.0112
0.0099
0.0091
0.0075
0.0110
0.0096
0.0087
0.0070
0.0091
0.0077
0.0066
0.0049
600
750
1000
0.0088
0.0084
0.0080
0.0086
0.0081
0.0077
0.0082
0.0077
0.0072
0.0074
0.0069
0.0063
0.0046
0.0040
0.0035
0.0074
0.0069
0.0064
0.0072
0.0067
0.0062
0.0070
0.0064
0.0058
0.0064
0.0058
0.0052
0.0042
0.0035
0.0029
12
10
8
0.3296
0.2133
0.1305
0.3811
0.2429
0.1552
0.4349
0.2741
0.1758
0.4848
0.3180
0.1951
0.5330
0.3363
0.2106
0.3312
0.2090
0.1286
0.3802
0.2410
0.1534
0.4328
0.2740
0.1745
0.4848
0.3052
0.1933
0.5331
0.3363
0.2115
6
4
2
1
0.0898
0.0595
0.0403
0.0332
0.1018
0.0660
0.0443
0.0357
0.1142
0.0747
0.0483
0.0396
0.1254
0.0809
0.0523
0.0423
0.1349
0.0862
0.0535
0.0428
0.0887
0.0583
0.0389
0.0318
0.1011
0.0654
0.0435
0.0349
0.1127
0.0719
0.0473
0.0391
0.1249
0.0800
0.0514
0.0411
0.1361
0.0849
0.0544
0.0428
1/0
2/0
3/0
4/0
0.0286
0.0234
0.0209
0.0172
0.0305
0.0246
0.0220
0.0174
0.0334
0.0275
0.0231
0.0179
0.0350
0.0284
0.0241
0.0177
0.0341
0.0274
0.0217
0.0170
0.0263
0.0227
0.0160
0.0152
0.0287
0.0244
0.0171
0.0159
0.0322
0.0264
0.0218
0.0171
0.0337
0.0274
0.0233
0.0179
0.0339
0.0273
0.0222
0.0172
11
250
300
350
500
0.0158
0.0137
0.0130
0.0112
0.0163
0.0139
0.0133
0.0111
0.0162
0.0143
0.0128
0.0114
0.0159
0.0144
0.0131
0.0099
0.0145
0.0122
0.0100
0.0076
0.0138
0.0126
0.0122
0.0093
0.0144
0.0128
0.0123
0.0094
0.0147
0.0133
0.0119
0.0094
0.0155
0.0132
0.0120
0.0091
0.0138
0.0125
0.0101
0.0072
12
600
750
1000
0.0101
0.0095
0.0085
0.0106
0.0094
0.0082
0.0097
0.0090
0.0078
0.0090
0.0084
0.0071
0.0063
0.0056
0.0043
0.0084
0.0081
0.0069
0.0085
0.0080
0.0068
0.0085
0.0078
0.0065
0.0081
0.0072
0.0058
0.0060
0.0051
0.0038
1
2
3
4
5
6
Copper Conductors
Aluminum Conductors
7
8
9
10
13
14
15
16
17
18
19
20
21
CA08104001E
April 2016

1.4-1
Sheet 01 057
Capacitors
Capacitors and Power Factor

Capacitor General Application
Considerations
Additional application information
is available in Tab 35 regarding
capacitors and harmonic filters
as follows:
Capacitor selection
Where to install capacitors in a plant
distribution system
Locating capacitors on reduced
voltage and multi-speed starters
Harmonic considerations
Eliminating harmonic problems
National Electrical Code
requirements
Medium Voltage
Capacitor Switching
Capacitance switching constitutes
severe operating duty for a circuit
breaker. At the time the breaker opens
at near current zero, the capacitor is
fully charged. After interruption, when
the alternating voltage on the source
side of the breaker reaches its opposite
maximum, the voltage that appears
across the contacts of the open breaker
is at least twice the normal peak lineto-neutral voltage of the circuit. If a
breakdown occurs across the open
contact, the arc is re-established. Due
to the circuit constants on the supply
side of the breaker, the voltage across
the open contact can reach three times
the normal line-to-neutral voltage.
After it is interrupted and with
subsequent alternation of the supply
side voltage, the voltage across the
open contact is even higher.
ANSI Standard C37.06 (indoor oilless

circuit breakers) indicates the preferred
ratings of Eatons Type VCP-W vacuum
breaker. For capacitor switching,
careful attention should be paid to
the notes accompanying the table.
The definition of the terms are in ANSI
Standard C37.04 Article 5.13 (for the
latest edition). The application guide
ANSI/IEEE Standard C37.012 covers the
method of calculation of the
quantities covered by C37.06 Standard.
Note that the definitions in C37.04
make the switching of two capacitors
banks in close proximity to the switchgear bus a back-to-back mode of
switching. This classification requires
a definite purpose circuit breaker
(breakers specifically designed for
capacitance switching).
Low Voltage Capacitor Switching

Circuit breakers and switches for use
with a capacitor must have a current
rating in excess of rated capacitor
current to provide for overcurrent from
overvoltages at fundamental frequency
and harmonic currents. The following
percent of the capacitor-rated current
should be used as a general guideline:
i
ii
1
Fused and unfused switches. . . . 165%
Molded case breaker or

equivalent . . . . . . . . . . . . . . . . . 150%
DSII power circuit breakers . . . . 135%

Magnum DS power
circuit breaker . . . . . . . . . . . . . . 135%
Contactors:
Open type . . . . . . . . . . . . . . . . . . . 135%
We recommend that such application

be referred to Eaton.
Enclosed type. . . . . . . . . . . . . . . . 150%
A breaker specified for capacitor

switching should include as applicable:
The NEC, Section 460.8(C), requires

the disconnecting means to be rated not
less than 135% of the rated capacitor
current (for 600 V and below).
1. Rated maximum voltage.

2. Rated frequency.
3. Rated open wire line charging
switching current.
4. Rated isolated cable charging and
shunt capacitor switching current.
5. Rated back-to-back cable
charging and back-to-back
capacitor switching current.
6. Rated transient overvoltage factor.
7. Rated transient inrush current and
its frequency.
8. Rated interrupting time.
9. Rated capacitive current
switching life.
10. Grounding of system and
capacitor bank.
Load break interrupter switches
are permitted by ANSI/IEEE Standard
C37.30 to switch capacitance, but they
must have tested ratings for the purpose.
Refer to Eaton Type MVS ratings.
See Tab 35 for switching device

ampere ratings. They are based on
percentage of capacitor-rated current
as indicated (above). The interrupting
rating of the switch must be selected
to match the system fault current
available at the point of capacitor
application. Whenever a capacitor
bank is purchased with less than the
ultimate kvar capacity of the rack or
enclosure, the switch rating should
be selected based on the ultimate
kvar capacitynot the initial installed
capacity.
Refer to Tab 35 for recommended
selection of capacitor switching
devices; recommended maximum
capacitor ratings for various motor
types and voltages; and for required
multipliers to determine capacitor kvar
required for power factor correction.
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E
1.4-2

April 2016
Sheet 01 058
Capacitors
i
ii
1
2
3
4
5
6
7
8
Motor Power Factor

Correction
See Tab 35 containing suggested
maximum capacitor ratings for
induction motors switched with the
capacitor. The data is general in nature
and representative of general purpose
induction motors of standard design.
The preferable means to select capacitor
ratings is based on the maximum
recommended kvar information
available from the motor manufacturer.
If this is not possible or feasible, the
tables can be used.
An important point to remember
is that if the capacitor used with the
motor is too large, self-excitation
may cause a motor-damaging overvoltage when the motor and capacitor
combination is disconnected from the
line. In addition, high transient torques
capable of damaging the motor shaft
or coupling can occur if the motor is
reconnected to the line while rotating
and still generating a voltage of
self-excitation.
Definitions
9
10
11
12
kvarrating of the capacitor in

reactive kilovolt-amperes. This value
is approximately equal to the motor
no-load magnetizing kilovars.
% ARpercent reduction in line

current due to the capacitor. A
capacitor located on the motor side
of the overload relay reduces line
current through the relay. Therefore, a
different overload relay and/or setting
may be necessary. The reduction in
line current may be determined by
measuring line current with and
without the capacitor or by calculation
as follows:
(Original PF)
% AR 100 100
(Improved PF)
If a capacitor is used with a lower kvar

rating than listed in tables, the % AR
can be calculated as follows:
Actual kvar
% AR Listed % AR
kvar in Table
The tables can also be used for other

motor ratings as follows:
A. For standard 60 Hz motors
operating at 50 Hz:
kvar = 1.71.4 of kvar listed
% AR = 1.81.35 of % AR listed
B. For standard 50 Hz motors
operating at 50 Hz:
kvar = 1.41.1 of kvar listed
% AR = 1.41.05 of % AR listed
C. For standard 60 Hz wound-rotor
motors:
kvar = 1.1 of kvar listed
% AR= 1.05 of % AR listed
To derate a capacitor used on a system

voltage lower than the capacitor
voltage rating, such as a 240 V
capacitor used on a 208 V system,
use the following formula:
Actual kvar =
2
Applied Voltage
Nameplate kvar ---------------------------------------------------------------------2
Nameplate Voltage
For the kVAC required to correct the

power factor from a given value of
COS 1 to COS 2, the formula is:
kVAC = kW (tan phase1tan phase2)
Capacitors cause a voltage rise.
At light load periods the capacitive
voltage rise can raise the voltage at
the location of the capacitors to an
unacceptable level. This voltage rise
can be calculated approximately by the
formula:
MVA r
% VR
MVA SC
MVAR is the capacitor rating and

MVASC is the system short-circuit
capacity.
With the introduction of variable speed
drives and other harmonic current
generating loads, the capacitor
impedance value determined must
not be resonant with the inductive
reactances of the system.
Note: For A, B, C, the larger multipliers

apply for motors of higher speeds; i.e.,
3600 rpm = 1.7 mult., 1800 rpm = 1.65
mult., etc.
13
14
15
16
17
18
19
20
21
CA08104001E

April 2016
1.4-3
Sheet 01 059
Protection and Coordination

substation transformer can be coordinated with the low voltage breakers.
Transformer damage points, based on
ANSI standards, and low voltage cable
heating limits can be plotted on this
set of curves to ensure that apparatus
limitations are not exceeded.
Ground-fault curves may also be
included in the coordination study
if ground-fault protection is provided,
but care must be used in interpreting
their meaning.
To ensure complete coordination, the

time-trip characteristics of all devices
in series should be plotted on a single
sheet of standard log-log paper.
Devices of different-voltage systems
can be plotted on the same sheet by
converting their current scales, using
the voltage ratios, to the same voltagebasis. Such a coordination plot is
shown in Figure 1.4-1. In this manner,
primary fuses and circuit breaker
relays on the primary side of a
Standard definitions have been

established for overcurrent protective
devices covering ratings, operation
and application systems.
MMotor (100 hp). Dashed line shows
initial inrush current, starting current
during 9-sec. acceleration, and drop to
124 A normal running current, all well
below CBA trip curve.
1000
900
800
700
600
ii
1
2
3
4
5
6
4.16 kV
6000
7000
8000
9000
10,000
40 50 60
5000
30
4000
20
3000
6 7 8 9 10
2000
600
700
800
900
1000
500
400
300
.5 .6 .7 .8 .9 1
SCALE X 100 = CURRENT IN AMPERES AT 480V

200
Overcurrents in a power distribution

system can occur as a result of both
normal (motor starting, transformer
inrush, etc.) and abnormal (overloads,
ground fault, line-to-line fault, etc.)
conditions. In either case, the fundamental purposes of current-sensing
protective devices are to detect the
abnormal overcurrent and with proper
coordination, to operate selectively
to protect equipment, property
and personnel while minimizing the
outage of the remainder of the system.
With the increase in electric power
consumption over the past few
decades, dependence on the continued supply of this power has also
increased so that the direct costs
of power outages have risen significantly. Power outages can create
dangerous and unsafe conditions as
a result of failure of lighting, elevators,
ventilation, fire pumps, security
systems, communications systems,
and the like. In addition, economic loss
from outages can be extremely high
as a result of computer downtime,
or, especially in industrial process
plants, interruption of production.
damage or withstand characteristics,

(e) calculation of maximum shortcircuit currents (and ground fault
currents if ground fault protection is
included) available at each protective
device location, (f) understanding of
operating characteristics and available
adjustments of each protective device,
(g) any special overcurrent protection
requirements including utility limitations. Refer to Figure 1.4-1.
70
80
90
100
Overcurrent Protection
and Coordination
250 MVA
1000
900
800
700
600
500
500
400
400
300
300
200
200
CA08104001E
250A
1000
kVA
5.75%
50
40
ANSI Three-Phase
Thru Fault
Protection Curve
(More Than 10 in
Lifetime)
30
TIME IN SECONDS
20
4,160V
480/277V
100
90
80
70
60
30
1,600A
20
10
9
8
7
6
600A
M
20,000A
175A
A
B
1
.9
.8
.7
.6
1
.9
.8
.7
.6
100 hp
124A FLC
13
14
15
.5
.5
X = Available fault current

including motor
contribution.
.4
.3
.4
.3
Ground
Fault Trip
.2
Transformer
Inrush
30
40 50 60
.02
SCALE X 100 = CURRENT IN AMPERES AT 480V
Figure 1.4-1. Time-Current Characteristic Curves for Typical Power Distribution System
Protective Devices Coordination Analysis
18
.03
19
.01
6000
7000
8000
9000
10,000
20
2000
6 7 8 9 10
600
700
800
900
1000
500
400
200
300
Max.
480V Fault
5000
.03
.04
4000
.04
.02
.05
Max. Three-Phase
4.16 kV Fault
.05
17
.1
.09
.08
.07
.06
3000
.1
.09
.08
.07
.06
.5 .6 .7 .8 .9 1
16
.2
.01
12
24,400A
10
11
50
40
19,600A
10
9
8
7
6
70
80
90
100
To study and accomplish coordination

requires (a) a one-line diagram, the
roadmap of the power distribution
system, showing all protective devices
and the major or important distribution
and utilization apparatus, (b) identification of desired degrees of power
continuity or criticality of loads
throughout system, (c) definition
of operating-current characteristics
(normal, peak, starting) of each
utilization circuit, (d) equipment
D
100
90
80
70
60
TIME IN SECONDS
Protective equipment must be adjusted

and maintained in order to function
properly when an overcurrent occurs,
but coordination begins during power
system design with the knowledgeable
analysis and selection and application
of each overcurrent protective device
in the series circuit from the power
source(s) to each load apparatus. The
objective of coordination is to localize
the overcurrent disturbance so that the
protective device closest to the fault
on the power-source side has the first
chance to operate; but each preceding
protective device upstream toward the
power source should be capable, within
its designed settings of current and
time, to provide backup and de-energize
the circuit if the fault persists. Sensitivity
of coordination is the degree to which
the protective devices can minimize
the damage to the faulted equipment.
20
21
1.4-4

April 2016
Sheet 01 060
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
ACB (175 A) coordinates selectively

with motor M on starting and running
and with all upstream devices, except
that CB B will trip first on low level
ground faults.
Maximum 480 V three-phase fault

indicated on the horizontal current axis.
BCB (600 A) coordinates selectively

with all upstream and downstream
devices, except will trip before A on
limited ground faults, since A has no
ground fault trips.
4160
I 480V I 4160V
480
CMain CB (1600 A) coordinates

selectively with all downstream
devices and with primary fuse D,
for all faults on load side of CB.
DPrimary fuse (250 A, 4160 V) coordinates selectively with all secondary
protective devices. Curve converted to
480 V basis. Clears transformer inrush
point (12 x FLC for 0.1 sec.), indicating
that fuse will not blow on inrush.
Fuse is underneath right-half of ANSI
three-phase withstand curve, indicating
fuse will protect transformer for highmagnitude faults up to ANSI rating.
Delta-wye secondary side short
circuit is not reflected to the primary
by the relation
VS
I P I S
VP
for L-L and L-G faults. For line-to-line

fault, the secondary (low voltage) side
fault current is 0.866 x I three-phase
fault current.
However, the primary (high voltage)
side fault is the same as if the secondary
fault was a three-phase fault. Therefore
in coordination studies, the knee of the
short-time pickup setting on the secondary breaker should be multiplied by
1 or 1.1547
0.866
before it is compared to the minimum

melting time of the upstream primary
fuse curve. In the example shown, the
knee is at 4000 A 30 sec., and the 30sec. trip time should be compared to
the MMT (minimum melt time) of the
fuse curve at 4000 x 1.1547 = 4619 A. In
this case, there is adequate clearance
to the fuse curve.
In the example shown, the ANSI
three-phase through fault protection
curve must be multiplied by 0.577
and replotted in order to determine
the protection given by the primary
for a single line to ground fault in
the secondary.
Maximum 4160 V three-phase fault

indicated, converted to 480 V basis.
The ANSI protection curves are

specified in ANSI C57.109 for liquidfilled transformers and C57.12.59 for
dry-type transformers.
Illustrative examples such as shown
here start the coordination study from
the lowest rated device proceeding
upstream. In practice, the setting or
rating of the utilitys protective device
sets the upper limit. Even in cases
where the customer owns the medium
voltage or higher distribution system,
the setting or rating of the lowest set
protective device at the source determines the settings of the downstream
devices and the coordination.
Therefore the coordination study
should start at the present setting
or rating of the upstream device and
work toward the lowest rated device. If
this procedure results in unacceptable
settings, the setting or rating of the
upstream device should be reviewed.
Where the utility is the sole source,
they should be consulted. Where the
owner has its own medium or higher
voltage distribution, the settings or
ratings of all upstream devices should
be checked.
If perfect coordination is not feasible,
then lack of coordination should be
limited to the smallest part of the system.
Application data is available for all
protective equipment to permit
systems to be designed for adequate
overcurrent protection and coordination. For circuit breakers of all types,
time-current curves permit selection of
instantaneous and inverse-time trips.
For more complex circuit breakers,
with solid-state trip units, trip curves
include long- and short-time delays,
as well as ground-fault tripping, with a
wide range of settings and features to
provide selectivity and coordination.
For current-limiting circuit breakers,
fuses, and circuit breakers with
integral fuses, not only are timecurrent characteristic curves available,
but also data on current-limiting
performance and protection for
downstream devices.
In a fully rated system, all circuit
breakers must have an interrupting
capacity adequate for the maximum
available fault current at their point of

application. All breakers are equipped
with long-time-delay (and possibly
short delay) and instantaneous overcurrent trip devices. A main breaker
may have short time-delay tripping to
allow a feeder breaker to isolate the
fault while power is maintained to all
the remaining feeders.
A selective or fully coordinated system
permits maximum service continuity.
The tripping characteristics of each
overcurrent device in the system must
be selected and set so that the breaker
nearest the fault opens to isolate the
faulted circuit, while all other breakers
remain closed, continuing power to
the entire unfaulted part of the system.
The National Electrical Code 1
contains specific requirements for
designing certain circuits with selective
coordination. Article 100 defines
selective coordination: Coordination
(Selective), the following definition:
Localization of an overcurrent condition to restrict outages to the circuit or
equipment affected, accomplished by
the choice of overcurrent protective
devices and their ratings or settings.
1
NEC 2011 NFPA 70: National Electrical Code

International Electrical Code Series.
Article 620.62 (elevators, dumbwaiters,

escalators, moving walks, wheelchair
lifts, and stairway chair lifts) requires
Where more than one driving machine
disconnecting means is supplied by a
single feeder, the overcurrent protective
devices in each disconnecting means
shall be selectively coordinated with
any other supply side overcurrent
protective device. A similar requirement under Article 700.27 is as follows;
Emergency system(s) overcurrent
devices shall be selectively coordinated
with all supply side overcurrent
protective devices. Article 701.27
states that Legally required standby
system(s) overcurrent devices shall be
selectively coordinated with all supply
side overcurrent devices.
Exception: Selective coordination
shall not be required between two
overcurrent devices located in series
if no loads are connected in parallel
with the downstream device.
In addition, for health care facilities,
Article 517.26, Application of Other
Articles requires that The essential
electrical system shall meet the
requirements of Article 700, except
as amended by Article 517.
CA08104001E
April 2016

1.4-5
Sheet 01 061

All breakers must have an interrupting
capacity not less than the maximum
available short-circuit current at their
point of application. A selective
system is a fully rated system with
tripping devices chosen and adjusted
to provide the desired selectivity.
The tripping characteristics of each
overcurrent device should not overlap, but should maintain a minimum
time interval for devices in series (to
allow for normal operating tolerances)
at all current values. Generally, a
maximum of four low voltage circuit
breakers can be operated selectively
in series, with the feeder or branch
breaker downstream furthest from
the source.
Specify true rms sensing devices in
order to avoid false trips due to rapid
currents or spikes. Specify tripping
elements with I2t or I4t feature for
improved coordination with other
devices having I2t or I4t (such as
OPTIM trip units) characteristics
and fuses.
In general for systems such as shown
in the example:
1. The settings or ratings of the
primary side fuse and main breaker
must not exceed the settings
allowed by NEC Article 450.
2. At 12 x IFL the minimum melting
time characteristic of the fuse
should be higher than 0.1 second.
3. The primary fuse should be to the
left of the transformer damage
curve as much as possible. The
correction factor for a single lineto-ground factor must be applied
to the damage curve.
4. The setting of the short-time delay
element must be checked against
the fuse MMT after it is corrected
for line-to-line faults.
5. The maximum fault current must
be indicated at the load side of
each protective device.
6. The setting of a feeder protective
device must comply with Article
240 and Article 430 of the NEC.
It also must allow the starting
and acceleration of the largest
motor on the feeder while carrying
all the other loads on the feeder.
Protection of Conductors (Excerpts

from NFPA 70-2011, Article 240.4)
Conductors, other than flexible cords
and fixture wires, shall be protected
against overcurrent in accordance with
their ampacities as specified in Section
310.15, unless otherwise permitted or
required in (A) through (G).
A. Power Loss Hazard. Conductor
overload protection shall not be
required where the interruption of
the circuit would create a hazard,
such as in a material handling
magnet circuit or fire pump circuit.
Short-circuit protection shall be
provided.
Note: FPN See NFPA 20-2003, standard
for the Installation of Stationary Pumps
for Fire Protection.
B. Devices Rated 800 A or Less. The

next higher standard overcurrent
device rating (above the ampacity
of the conductors being protected)
shall be permitted to be used,
provided all of the following
conditions are met.
1. The conductors being protected
are not part of a branch circuit
supplying more than one receptacle
for cord-and-plug-connected
portable loads.
2. The ampacity of the conductors
does not correspond with the
standard ampere rating of a fuse or
a circuit breaker without overload
trip adjustments above its rating
(but that shall be permitted to have
other trip or rating adjustments).
3. The next higher standard rating
selected does not exceed 800 A.
C. Overcurrent Devices Rated Over
800 A. Where the overcurrent
device is rated over 800 A, the
ampacity of the conductors it
protects shall be equal to or
greater than the rating of the
overcurrent device as defined in
Section 240.6.
D. Small Conductors. Unless
specifically permitted in 240.4(E)
or 240.4(G), the overcurrent
protection shall not exceed 15 A
for 14 AWG, 20 A for 12 AWG, and
30 A for 10 AWG copper; or 15 A
for 12 AWG and 25 A for 10 AWG
aluminum and copper-clad
aluminum after any correction
factors for ambient temperature
and number of conductors have
been applied.
E. Tap Conductors. Tap conductors

shall be permitted to be protected
against overcurrent in accordance
with the following:
1. 210.19(A)(3) and (A)(4) Household
Ranges and Cooking Appliances
and Other Loads.
i
ii
1
2. 240.5(B)(2) Fixture Wire.

3. 240.21 Location in Circuit.
4. 368.17(B) Reduction in Ampacity

Size of Busway.
5. 368.17(C) Feeder or Branch Circuits

(busway taps).
6. 430.53(D) Single Motor Taps.
Circuit Breaker Cable

Temperature Ratings
UL listed circuit breakers rated 125 A or

less shall be marked as being suitable
for 60 C (140F), 75 C (167 F) only or
60/75 C (140/167F) wire. All Eaton
breakers rated 125 A or less are marked
60/75 C (140/167 F). All UL listed circuit
breakers rated over 125 A are suitable
for 75 C conductors. Conductors rated
for higher temperatures may be used,
but must not be loaded to carry more
current than the 75 C ampacity of that
size conductor for equipment marked
or rated 75 C or the 60 C ampacity of
that size conductor for equipment
marked or rated 60 C. However, when
applying derated factors, so long as the
actual load does not exceed the lower
of the derated ampacity or the 75 C or
60 C ampacity that applies.
Zone Selective Interlocking

Trip elements equipped with zone
selective interlocking, trip without
intentional time delay unless a
restraint signal is received from
a protective device downstream.
Breakers equipped with this feature
reduce the damage at the point of
fault if the fault occurs at a location
between the zone of protection.
The upstream breaker upon receipt
of the restraint signal will not trip until
its time-delay setting times out. If the
breaker immediately downstream of the
fault does not open, then after timing
out, the upstream breaker will trip.
Breakers equipped with ground fault
trip elements should also be specified
to include zone interlocking for the
ground fault trip element.
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E
1.4-6

April 2016
Sheet 01 062
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Ground Fault Protection
Suggested Ground Fault Settings
Article 230.95 of NEC requires groundfault protection of equipment shall be

provided for solidly grounded wye
electrical services of more than 150 V
to ground, but not exceeding 600 V
phase-to-phase for each service
disconnect rated 1000 A or more.
For the main devices:

A ground fault pickup setting equal
to 2030% of the main breaker rating
but not to exceed 1200 A, and a time
delay equal to the delay of the shorttime element, but not to exceed
1 second.
The rating of the service disconnect

shall be considered to be the rating
of the largest fuse that can be installed
or the highest continuous current trip
setting for which the actual overcurrent
device installed in a circuit breaker is
rated or can be adjusted.
For the feeder ground fault setting:

A setting equal to 2030% of the feeder
ampacity and a time delay to coordinate
with the setting of the main (at least
6 cycles below the main).
The maximum allowable settings are:

1200 A pickup, 1 second or less trip
delay at currents of 3000 A or greater.
The characteristics of the ground-fault
trip elements create coordination
problems with downstream devices
not equipped with ground fault
protection. The National Electrical
Code exempts fire pumps and
continuous industrial processes
from this requirement.
It is recommended that in solidly
grounded 480/277 V systems where
main breakers are specified to be
equipped with ground fault trip elements
that the feeder breakers be specified
to be equipped with ground fault trip
elements as well.
If the desire to selectively coordinate

ground fault devices results in settings
that do not offer adequate damage
protection against arcing single lineground faults, the design engineer
should decide between coordination
and damage limitation.
For low voltage systems with highmagnitude available short-circuit
currents, common in urban areas and
large industrial installations, several
solutions are available. High interrupting Series C molded case breakers,
current-limiting circuit breakers, or
current-limiting fuses, limiters integral
with molded-case circuit breakers
(TRI-PAC) or mounted on power
circuit breakers (MDSL) can be used to
handle these large fault currents. To
provide current limiting, these devices
must clear the fault completely within
the first half-cycle, limiting the peak
current (Ip) and heat energy (I2t)
let-through to considerably less than
what would have occurred without
the device. For a fully fusible system,
rule-of-thumb fuse ratios or more
accurate I2t curves can be used to
provide selectivity and coordination.
For fuse-breaker combinations, the
fuse should be selected (coordinated)
so as to permit the breaker to handle
those overloads and faults within its
capacity; the fuse should operate
before or with the breaker only on
large faults, approaching the interrupting capacity of the breaker, to minimize
fuse blowing. Recently, unfused, truly
current-limiting circuit breakers with
interrupting ratings adequate for the
largest systems (Type Series C, FDC,
JDC, KDC, LDC and NDC frames
or Type Current Limit-R) have
become available.
The Series G high performance,

current-limiting circuit breaker series
offers interrupting ratings to 200 kA.
Frames are EGC, EGU, EGX, JGC, JGU,
JGX, LGC, LGU and LGX.
Any of these current-limiting devices
fuses, fused breakers or current-limiting breakerscannot only clear these
large faults safely, but also will limit
the Ip and I2t let-through significantly
to prevent damage to apparatus
downstream, extending their zone
of protection. Without the current
limitation of the upstream device,
the fault current could exceed the withstand capability of the downstream
equipment. Underwriters
Laboratories tests and lists these
series combinations. Application
information is available for
combinations that have been tested
and UL-listed for safe operation
downstream from MDSL, TRI-PAC,
and Current Limit-R, or Series C
breakers of various ratings, under
high available fault currents.
Protective devices in electrical
distribution systems may be properly
coordinated when the systems are
designed and built, but that is no
guarantee that they will remain
coordinated. System changes and
additions, plus power source changes,
frequently modify the protection
requirements, sometimes causing loss
of coordination and even increasing
fault currents beyond the ratings of
some devices. Consequently, periodic
study of protective-device settings
and ratings is as important for safety
and preventing power outages
as is periodic maintenance of the
distribution system.
19
20
21
CA08104001E

April 2016
1.4-7
Sheet 01 063
Grounding
above ground potential. Any person

coming in contact with such an object
while grounded could be seriously
injured or killed. In addition, current
flow from the accidental grounding of
an energized part of the system could
generate sufficient heat (often with
arcing) to start a fire. To prevent the
establishment of such unsafe potential difference requires that (1) the
equipment grounding conductor provide a return path for ground fault currents of sufficiently low impedance to
prevent unsafe voltage drop, and (2)
the equipment grounding conductor
be large enough to carry the maximum
ground fault current, without burning
off, for sufficient time to permit protective devices (ground fault relays, circuit
breakers, fuses) to clear the fault. The
grounded conductor of the system
(usually the neutral conductor), although
grounded at the source, must not be
used for equipment grounding.
Grounding encompasses several

different but interrelated aspects of
electrical distribution system design
and construction, all of which are
essential to the safety and proper
operation of the system and equipment supplied by it. Among these
are equipment grounding, system
grounding, static and lightning
protection, and connection to earth
as a reference (zero) potential.
1. Equipment Grounding
Equipment grounding is essential
to safety of personnel. Its function is
to ensure that all exposed noncurrentcarrying metallic parts of all structures
and equipment in or near the electrical
distribution system are at the same
potential, and that this is the zero
reference potential of the earth.
Equipment grounding is required
by both the National Electrical Code
(Article 250) and the National Electrical
Safety Code regardless of how the
power system is grounded. Equipment
grounding also provides a return path
for ground fault currents, permitting
protective devices to operate. Accidental contact of an energized conductor of
the system with an improperly
grounded noncurrent-carry metallic
part of the system (such as a motor
frame or panelboard enclosure) would
raise the potential of the metal object
The equipment grounding conductor

may be the metallic conduit or raceway
of the wiring system, or a separate
equipment grounding conductor,
run with the circuit conductors, as
permitted by NEC. If a separate
equipment grounding conductor is
used, it may be bare or insulated; if
insulated, the insulation must be green,
green with yellow stripe or green tape.
Conductors with green insulation may
not be used for any purpose other than
for equipment grounding.
The equipment grounding system

must be bonded to the grounding
electrode at the source or service;
however, it may be also connected
to ground at many other points.
This will not cause problems with
the safe operation of the electrical
distribution system. Where computers,
data processing, or microprocessorbased industrial process control
systems are installed, the equipment
grounding system must be designed
to minimize interference with their
proper operation. Often, isolated
grounding of this equipment, or
isolated electrical supply systems are
required to protect microprocessors
from power system noise that does
not in any way affect motors or other
electrical equipment. Such systems
must use single-point ground concept
to minimize noise and still meet
the NEC requirements. Any separate
isolated ground mat must be tied to the
rest of the facility ground mat system
for NEC compliance.
2. System Grounding
System grounding connects the
electrical supply, from the utility, from
transformer secondary windings, or
from a generator, to ground. A system
can be solidly grounded (no intentional
impedance to ground), impedance
grounded (through a resistance or
reactance), or ungrounded (with no
intentional connection to ground.
3. Medium Voltage System: Grounding

Description
A
Ungrounded
B
Solidly Grounded
C
Reactance Grounded
D
Resistance Grounded
E
Resonant Grounded
(1) Apparatus
insulation
(2) Fault to
ground current
Fully insulated
Lowest
Partially graded
Partially graded
Partially graded
Usually low
Maximum value rarely

higher than three-phase
short circuit current
Cannot satisfactorily be
reduced below one-half
or one-third of values for
solid grounding
Low
Improved over solid

grounding particularly
if used at receiving end
of system
Improved over solid

grounding particularly
if used at receiving end
of system
(4) Relaying
Difficult
Satisfactory
Satisfactory
Satisfactory
(5) Arcing
grounds
(6) Localizing
faults
Likely
Unlikely
Unlikely
Effect of fault transmitted

as excess voltage on
sound phases to all
parts of conductively
connected network
Likely
Effect of faults localized

to system or part of
system where they occur
Possible if reactance is
excessive
Effect of faults localized to
system or part of system
where they occur unless
reactance is quite high
Negligible except when

Petersen coil is short
circuited for relay
purposes when it may
compare with solidly
grounded systems
Is eliminated from
consideration during
single line-to-ground
faults unless neutralizer
is short circuited to
isolate fault by relays
Requires special
provisions but can be
made satisfactory
Unlikely
Effect of faults
transmitted as excess
voltage on sound phases
to all parts of conductively
connected network
Unlikely unless
resistance is quite high
and insulation weak
Effect of faults
transmitted as excess
voltage on sound phases
to all parts of conductively
connected network
Seem to be more likely
but conclusive information
not available
(7) Double
faults
CA08104001E
Usually unimportant
Lower than with other

methods but can be
made satisfactory by use
of high-speed breakers
Likely
Unlikely unless
reactance is quite high
and insulation weak
ii
1
2
3
4
5
6
7
8
9
10
11
12
Table 1.4-1. Features of Ungrounded and Grounded Systems (from ANSI C62.92)
(3) Stability
13
14
15
16
17
18
19
20
21
1.4-8

April 2016
Sheet 01 064
i
ii
Table 1.4-1. Features of Ungrounded and Grounded Systems (Continued)

Description
A
Ungrounded
(8) Lightning
protection
C
Reactance Grounded
D
Resistance Grounded
E
Resonant Grounded
Ungrounded neutral
Highest efficiency and
service arresters must be lowest cost
applied at sacrifice in cost
and efficiency
If reactance is very high

arresters for ungrounded
neutral service must be
applied at sacrifice in cost
and efficiency
Arresters for ungrounded,

neutral service usually
must be applied at
sacrifice in cost and
efficiency
Ungrounded neutral
service arresters must
be applied at sacrifice
in cost and efficiency
(9) Telephone
interference
Will usually be low

except in cases of double
faults or electrostatic
induction with neutral
displaced but duration
may be great
Will be reduced from

solidly grounded values
Will be reduced from

solidly grounded values
Will be low in magnitude

except in cases of double
faults or series resonance
at harmonic frequencies,
but duration may be great
(10) Radio
interference
May be quite high during Minimum

faults or when neutral
is displayed
Greater than for

solidly grounded,
when faults occur
Greater than for

solidly grounded,
when faults occur
May be high during faults
(11) Line
availability
Will inherently clear

Must be isolated for
themselves if total length each fault
of interconnected line is
low and require isolation
from system in increasing percentages as length
becomes greater

each fault

each fault
Need not be isolated but

will inherently clear itself
in about 60 to 80 percent
of faults
Satisfactory with solidlyor reactance-grounded

systems with proper
attention to relaying
Cannot be interconnected
unless interconnected
system is resonant
grounded or isolating
transformers are used.
Requires coordination
between interconnected
systems in neutralizer
settings
1
2
3
4
5
6
7
B
Solidly Grounded
Will be greatest in
magnitude due to higher
fault currents but can
be quickly cleared
particularly with high
speed breakers
(12) Adaptability Cannot be interconnected Satisfactory indefinitely

Satisfactory indefinitely
to interconnection unless interconnecting
with reactance-grounded with solidly-grounded
system is ungrounded
systems
systems
or isolating transformers
are used
8
9
(13) Circuit
breakers
Interrupting capacity
determined by threephase conditions
Same interrupting
capacity as required for
three-phase short circuit
will practically always be
satisfactory
determined by threephase fault conditions
(14) Operating
procedure
Ordinarily simple but

possibility of double
faults introduces
complication in times
of trouble
Simple
Simple
Simple
Taps on neutralizers must

be changed when major
system switching is performed and difficulty may
arise in interconnected
systems. Difficult to tell
where faults are located
(15) Total cost
High, unless conditions

Lowest
are such that arc tends
to extinguish itself, when
transmission circuits may
be eliminated, reducing
total cost
Intermediate
Intermediate
Highest unless the arc

suppressing characteristic is relied on to eliminate
transmission circuits
when it may be lowest
for the particular types
of service
10
11
12
13
14
15
16
17
18
19
20
21
Because the method of grounding

affects the voltage rise of the unfaulted
phases above ground, ANSI C62.92
classifies systems from the point of
view of grounding in terms of a
coefficient of grounding
Highest Power Frequency
rms Line Ground Voltage
COG = --------------------------------------------------------------------------------------------rms Line Line Voltage at Fault
Location with the Fault Removed
This same standard also defines

systems as effectively grounded when
COG .8 such a system would have
X0 /X1 3.0 and R0 /X1 1.0. Any other
grounding means that does not satisfy
these conditions at any point in a
system is not effectively grounded.
The aforementioned definition is

of significance in medium voltage
distribution systems with long lines
and with grounded sources removed
during light load periods so that in
some locations in the system the
X0 /X1, R0 /X1 may exceed the defining
limits. Other standards (cable and
lightning arrester) allow the use of
100% rated cables and arresters
selected on the basis of an effectively
grounded system only where the
criteria in the above are met. In
effectively grounded system the lineto-ground fault current is high and
there is no significant voltage rise in
the unfaulted phases.
With selective ground fault isolation
the fault current should be at least 60%
of the three-phase current at the point

of fault. Damage to cable shields must
be checked. Although this fact is not
a problem except in small cables, it is a
good idea to supplement the cable
shields returns of ground fault current
to prevent damage, by installing an
equipment grounding conductor.
The burdens on the current transformers
must be checked also (for saturation
considerations), where residually
connected ground relays are used
and the current transformers supply
current to phase relays and meters.
If ground sensor current transformers
(zero sequence type) are used they
must be of high burden capacity.
CA08104001E

April 2016
1.4-9
Sheet 01 065

Table 1.4-2 taken from ANSI-C62.92
indicates the characteristics of the
various methods of grounding.
should not be limited to less than the

current transformers rating of the
source. This rule will provide sensitive
differential protection for wye-connected
generators and transformers against
line-to-ground faults near the neutral.
Of course, if the installation of ground
fault differential protection is feasible,
or ground sensor current transformers
are used, sensitive differential relaying
in resistance grounded system with
greater fault limitation is feasible.
In general, ground sensor current
transformers (zero sequence) do not
have high burden capacity. Resistance
grounded systems limit the circulating
currents of triple harmonics and limit
the damage at the point of fault. This
method of grounding is not suitable
for line-to-neutral connection of loads.
Reactance Grounding
It is generally used in the grounding
of the neutrals of generators directly
connected to the distribution system
bus, in order to limit the line-to-ground
fault to somewhat less than the threephase fault at the generator terminals.
If the reactor is so sized, in all probability
the system will remain effectively
grounded.
Resistance Grounded
Medium voltage systems in general
should be low resistance grounded.
The ground fault is typically limited to
about 200400 A but less than 1000 A
(a cable shield consideration). With a
properly sized resistor and relaying
application, selective fault isolation
is feasible. The fault limit provided
has a bearing on whether residually
connected relays are used or ground
sensor current transformers are used
for ground fault relaying.
On medium voltage systems, 100%

cable insulation is rated for phase-toneutral voltage. If continued operation
with one phase faulted to ground is
desired, increased insulation thickness
is required. For 100% insulation, fault
clearance is recommended within
one minute; for 133% insulation, one
hour is acceptable; for indefinite
operation, as long as necessary,
173% insulation is required.
In general, where residually connected

ground relays are used (51N), the fault
current at each grounded source
Table 1.4-2. Characteristics of Grounding
Grounding Classes
and Means
A. Effectively
1. Effective
2. Very effective
B. Noneffectively
1. Inductance
a. Low inductance
b. High inductance
2. Resistance
a. Low resistance
b. High resistance
3. Inductance and resistance
4. Resonant
5. Ungrounded/capacitance
a. Range A
b. Range B
1
2
3
4
5
6
7
8
9
Ratios of Symmetrical
Component Parameters 1
Percent Fault
Current
Per Unit Transient

LG Voltage
X0/X1
R0/X1
R0/X0
0-3
0-1
0-1
0-0.1
>60
>95
2
<1.5
3-10
>10
0-1
<2
>25
<25
<2.3
2.73 8
0-10
>10
5
>100
2
(-1)
>2
<25
<1
<10
<1
<2.5
2.73
2.73
2.73
- to -40 6
-40 to 0
<8
>8
3 9
>3 79
Values of the coefficient of grounding (expressed as a percentage of maximum phase-to-phase

voltage) corresponding to various combinations of these ratios are shown in the ANSI C62.92
Appendix figures. Coefficient of grounding affects the selection of arrester ratings.
Ground-fault current in percentage of the three-phase short-circuit value.
Transient line-to-ground voltage, following the sudden initiation of a fault in per unit of the crest
of the prefault line-to-ground operating voltage for a simple, linear circuit.
In linear circuits, Class A1 limits the fundamental line-to-ground voltage on an unfaulted phase to
138% of the prefault voltage; Class A2 to less than 110%.
See ANSI 62.92 para. 7.3 and precautions given in application sections.
Usual isolated neutral (ungrounded) system for which the zero-sequence reactance is capacitive
(negative).
Same as NOTE (6) and refer to ANSI 62.92 para. 7.4. Each case should be treated on its own merit.
Under restriking arcing ground fault conditions (e.g., vacuum breaker interrupter operation),
this value can approach 500%.
Under arcing ground fault conditions, this value can easily reach 700%, but is essentially unlimited.
Grounding Point
The most commonly used grounding
point is the neutral of the system or the
neutral point created by means of a
zigzag or a wye-broken delta grounding
transformer in a system that was operating as an ungrounded delta system.
In general, it is a good practice that all
source neutrals be grounded with the
same grounding impedance magnitude.
However, neutrals should not be tied
together to a single resistor. Where
one of the medium voltage sources is
the utility, their consent for impedance
grounding must be obtained.
The neutral impedance must have a
voltage rating at least equal to the rated
line-to-neutral voltage class of the system. It must have at least a 10-second
rating equal to the maximum future
line-to-ground fault current and a
continuous rating to accommodate the
triple harmonics that may be present.
4. Low Voltage System: Grounding

Solidly grounded three-phase systems
(Figure 1.4-2) are usually wyeconnected, with the neutral point
grounded. Less common is the redleg or high-leg delta, a 240 V system
supplied by some utilities with one
winding center-tapped to provide 120 V
to ground for lighting. This 240 V, threephase, four-wire system is used where
120 V lighting load is small compared
to 240 V power load, because the
installation is low in cost to the utility.
A corner-grounded three-phase delta
system is sometimes found, with
one phase grounded to stabilize all
voltages to ground. Better solutions
are available for new installations.
Phase A
Phase B
Phase C
Neutral
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Grounded Wye
Phase B
Phase C
Phase A
Neutral
17
18
Center-Tapped (High-Leg) Delta
Phase A
Phase B
Phase C
19
20
Corner-Grounded Delta
Figure 1.4-2. Solidly Grounded Systems

CA08104001E
21

April 2016
Sheet 01 066
i
ii
1
2
3
4
Ungrounded systems (Figure 1.4-3)

can be either wye or delta, although
the ungrounded delta system is far
more common.
Phase A
Phase B
Phase C
Ungrounded Delta
Phase A
Phase B
Phase C
Ungrounded Wye
Figure 1.4-3. Ungrounded Systems
5
6
7
Resistance-grounded systems
(Figure 1.4-4) are simplest with a
wye connection, grounding the neutral
point directly through the resistor.
Delta systems can be grounded by
means of a zig-zag or other grounding
transformer. Wye broken delta
transformer banks may also be used.
8
9
10
15
16
17
18
19
20
Phase A
12
14
Phase C
Resistance-Grounded Wye
11
13
Phase A
Phase B

N
R
Phase B
Phase C
Delta With Derived Neutral ResistanceGrounded Using Zig-Zag Transformer
Figure 1.4-4. Resistance-Grounded Systems

This derives a neutral point, which
can be either solidly or impedancegrounded. If the grounding transformer
has sufficient capacity, the neutral
created can be solidly grounded and
used as part of a three-phase, four-wire
system. Most transformer-supplied
systems are either solidly grounded
or resistance grounded. Generator
neutrals are often grounded through
a reactor, to limit ground fault (zero
sequence) currents to values the
generator can withstand.
Selecting the Low Voltage System

Grounding Method
There is no one best distribution
system for all applications. In choosing
among solidly grounded, resistance
grounded, or ungrounded power
distribution, the characteristics of the
system must be weighed against the
requirements of power loads, lighting
loads, continuity of service, safety
and cost.
Under ground fault conditions, each
system behaves very differently. A
solidly grounded system produces
high fault currents, usually with arcing,
and the faulted circuit must be cleared
on the first fault within a fraction of a
second to minimize damage. An
ungrounded system will pass limited
current into the first ground faultonly
the charging current of the system,
caused by the distributed capacitance
to ground of the system wiring and
equipment. In low voltage systems,
this is rarely more than 1 or 2 A.
Therefore, on first ground fault, an
ungrounded system can continue in
service, making it desirable where
power outages cannot be tolerated.
However, if the ground fault is
intermittent, sputtering or arcing, a
high voltageas much as 6 to 8 times
phase voltagecan be built up across
the system capacitance, from the
phase conductors to ground. Similar
high voltages can occur as a result
of resonance between system
capacitance and the inductances
of transformers and motors in the
system. The phase-to-phase voltage
is not affected. This high transient
phase-to-ground voltage can puncture
insulation at weak points, such as
motor windings, and is a frequent
cause of multiple motor failures on
ungrounded systems. Locating a first
fault on an ungrounded system can
be difficult. If, before the first fault is
cleared, a second ground fault occurs
on a different phase, even on a
different, remote feeder, it is a highcurrent phase-to-ground-to-phase
fault, usually arcing, that can cause
severe damage if at least one of the
grounds is not cleared immediately.
If the second circuit is remote, enough
current may not flow to cause
protection to operate. This can leave
high voltages and stray currents on
structures and jeopardize personnel.
In general, where loads will be
connected line-to-neutral, solidly
grounded systems are used. High
resistance grounded systems are
used as substitutes for ungrounded

systems where high system
availability is required.
With one phase grounded, the voltage
to ground of the other two phases
rises 73%, to full phase-to-phase
voltage. In low voltage systems this
is not important, since conductors
are insulated for 600 V.
A low voltage resistance grounded
system is normally grounded so that
the single line-to-ground fault current
exceeds the capacitive charging
current of the system. If data for the
charging current is not available, use
4050 ohm resistor in the neutral
of the transformer.
In commercial and institutional
installations, such as office buildings,
shopping centers, schools and hospitals,
lighting loads are often 50% or more
of the total load. In addition, a feeder
outage on first ground fault is seldom
crucialeven in hospitals, that have
emergency power in critical areas. For
these reasons, a solidly grounded wye
distribution, with the neutral used for
lighting circuits, is usually the most
economical, effective and convenient
design. In some instances, it is an
NEC requirement.
In industrial installations, the effect
of a shutdown caused by a single
ground fault could be disastrous.
An interrupted process could cause the
loss of all the materials involved, often
ruin the process equipment itself, and
sometimes create extremely dangerous situations for operating personnel.
On the other hand, lighting is usually
only a small fraction of the total
industrial electrical load. A solidly
grounded neutral circuit conductor
is not imperative and, when required,
can be obtained from inexpensive
lighting transformers.
Because of the ability to continue in
operation with one ground fault on
the system, many existing industrial
plants use ungrounded delta distribution. Today, new installations can have
all the advantages of service continuity
of the ungrounded delta, yet minimize
the problems of the system, such
as the difficulty of locating the first
ground fault, risk of damage from a
second ground fault, and damage
transient overvoltages. A highresistance grounded wye distribution
can continue in operation with a
ground fault on the system and will
not develop transient overvoltages.
21
CA08104001E
April 2016

1.4-11
Sheet 01 067

And, because the ground point is
established, locating a ground fault is
less difficult than on an ungrounded
system especially when a pulsing
contactor design is applied. When
combined with sensitive ground-fault
protection, damage from a second
ground fault can be nearly eliminated.
Ungrounded delta systems can be
converted to high-resistance grounded
systems, using a zig-zag or other
grounding transformer to derive a
neutral, with similar benefits, see
Tab 36. While the majority of
manufacturing plants use solidly
grounded systems, in many instances,
the high-resistance grounded distribution will be the most advantageous.
Ground Fault Protection

A ground fault normally occurs in one
of two ways: by accidental contact of
an energized conductor with normally
grounded metal, or as a result of
an insulation failure of an energized
conductor. When an insulation failure
occurs, the energized conductor
contacts normally noncurrent-carrying
grounded metal, which is bonded to
or part of the equipment grounding
conductor. In a solidly grounded
system, the fault current returns to the
source primarily along the equipment
grounding conductors, with a small
part using parallel paths such as building steel or piping. If the ground return
impedance was as low as that of the
circuit conductors, ground fault currents
would be high, and the normal phase
overcurrent protection would clear
them with little damage. Unfortunately,
the impedance of the ground return
path is usually higher, the fault itself
is usually arcing and the impedance
of the arc further reduces the fault
current. In a 480Y/277 V system, the
voltage drop across the arc can be
from 70 to 140 V. The resulting ground
fault current is rarely enough to cause
the phase overcurrent protection
device to open instantaneously and
prevent damage. Sometimes, the
ground fault is below the trip setting of
the protective device and it does not
trip at all until the fault escalates and
extensive damage is done. For these
reasons, low level ground protection
devices with minimum time delay
settings are required to rapidly clear
ground faults. This is emphasized by
the NEC requirement that a ground
fault relay on a service shall have a
maximum delay of one second for
faults of 3000 A or more.
The NEC (Sec. 230.95) requires that
ground fault protection, set at no more
than 1200 A, be provided for each service
CA08104001E
disconnecting means rated 1000 A or

more on solidly grounded wye services
of more than 150 V to ground, but
not exceeding 600 V phase-to-phase.
Practically, this makes ground fault
protection mandatory on 480Y/277 V
services, but not on 208Y/120 V services. On a 208 V system, the voltage
to ground is 120 V. If a ground fault
occurs, the arc goes out at current
zero, and the voltage to ground is
often too low to cause it to restrike.
Therefore, arcing ground faults on 208
V systems tend to be self-extinguishing. On a 480 V system, with
277 V to ground, restrike usually takes
place after current zero, and the arc
tends to be self-sustaining, causing
severe and increasing damage, until
the fault is cleared by a protective
device.
The NEC requires ground fault
protection on the service disconnecting
means. This protection works so fast
that for ground faults on feeders, or
even branch circuits, it will often open
the service disconnect before the
feeder or branch circuit overcurrent
device can operate. This is highly
undesirable, and in the NEC (230.95)
a Fine Print Note (FPN) states that
additional ground fault protective
equipment will be needed on feeders
and branch circuits where maximum
continuity of electric service is necessary. Unless it is acceptable to disconnect the entire service on a ground
fault almost anywhere in the system,
such additional stages of ground
fault protection must be provided.
At least two stages of protection are
mandatory in health care facilities
(NEC Sec. 517.17).
Overcurrent protection is designed
to protect conductors and equipment
against currents that exceed their
ampacity or rating under prescribed
time values. An overcurrent can result
from an overload, short circuit or (high
level) ground fault condition. When
currents flow outside the normal
current path to ground, supplementary
ground fault protection equipment will
be required to sense low-level ground
fault currents and initiate the protection
required. Normal phase overcurrent
protection devices provide no protection
against low-level ground faults.
There are three basic means of sensing
ground faults. The most simple and
direct method is the ground return
method as illustrated in Figure 1.4-5.
This sensing method is based on the fact
that all currents supplied by a transformer must return to that transformer.
Main
Neutral
Service
Transformer
ii
GFR
Sensor
Typical
Feeder
Ground Bus
Main Bonding
Jumper
Grounding
Electrode
Conductor
Equipment
Grounding
Conductor
Typical
4W Load
Figure 1.4-5. Ground Return Sensing Method

When an energized conductor faults
to grounded metal, the fault current
returns along the ground return path to
the neutral of the source transformer.
This path includes the main bonding
jumper as shown in Figure 1.4-5.
A current sensor on this conductor
(which can be a conventional bar-type
or window type CT) will respond to
ground fault currents only. Normal
neutral currents resulting from
unbalanced loads will return along
the neutral conductor and will not be
detected by the ground return sensor.
This is an inexpensive method of sensing
ground faults where protection per
NEC (230.95) is desired. For it to
operate properly, the neutral must be
grounded in only one place as indicated
in Figure 1.4-5. In many installations,
the servicing utility grounds the neutral
at the transformer and additional
grounding is required in the service
equipment per NEC (250.24(A)(2)).
In such cases, and others including
multiple source with multiple, interconnected neutral ground points,
residual or zero sequence ground
sensing methods should be employed.
A second method of detecting ground
faults involves the use of a zero
sequence sensing method, as illustrated in Figure 1.4-6. This sensing
method requires a single, specially
designed sensor either of a toroidal
or rectangular shaped configuration.
This core balance current transformer
surrounds all the phase and neutral
conductors in a typical three-phase,
four-wire distribution system. The
sensing method is based on the fact
that the vectorial sum of the phase and
neutral currents in any distribution
circuit will equal zero unless a ground
fault condition exists downstream from
the sensor. All currents that flow only
in the circuit conductors, including
balanced or unbalanced phase-to-phase
and phase-to-neutral normal or fault
currents, and harmonic currents, will
result in zero sensor output.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21

April 2016
Sheet 01 068
ii
1
However, should any conductor become

grounded, the fault current will return
along the ground pathnot the normal
circuit conductorsand the sensor will
have an unbalanced magnetic flux
condition, and a sensor output will
be generated to actuate the ground
fault relay.
Zero
Sequence
Sensor
neutral. In a residual sensing scheme,

the relationship of the polarity markings
as noted by the X on each sensor
is critical. Because the vectorial sum of
the currents in all the conductors will
total zero under normal, non-ground
faulted conditions, it is imperative
that proper polarity connections are
employed to reflect this condition.
Alternate
Sensor
Location
Sensor
Polarity
Marks
Main
levels of ground fault protection are

desired for added service continuity.
Additional grounding points may be
employed upstream of the residual
sensors, but not on the load side.
Both the zero sequence and
residual sensing methods have
been commonly referred to as
vectorial summation methods.
Most distribution systems can use
either of the three sensing methods
exclusively or a combination of the
sensing methods depending upon
the complexity of the system and
the degree of service continuity and
selective coordination desired.
Different methods will be required
depending upon the number of supply
sources, and the number and location
of system grounding points.
Residual
Sensors
Main
Neutral
Neutral
Typical
Feeder
5
Typical
4W Load
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Figure 1.4-6. Zero Sequence Sensing Method

Zero sequence sensors are available
with various window openings for
circuits with small or large conductors,
and even with large rectangular windows to fit over busbars or multiple
large size conductors in parallel. Some
sensors have split cores for installation
over existing conductors without
disturbing the connections.
This method of sensing ground faults
can be employed on the main disconnect where protection per NEC (230.95)
is desired. It can also be easily employed
in multi-tier systems where additional
desired for added service continuity.
Additional grounding points may be
employed upstream of the sensor, but
not on the load side.
Ground fault protection employing
ground return or zero sequence sensing
methods can be accomplished by the
use of separate ground fault relays
(GFRs) and disconnects equipped with
standard shunt trip devices or by circuit
breakers with integral ground fault
protection with external connections
arranged for these modes of sensing. In
some cases, a reliable source of control
power is needed.
The third basic method of detecting
ground faults involves the use of
multiple current sensors connected in
a residual sensing method as illustrated
in Figure 1.4-7. This is a very common
sensing method used with circuit breakers equipped with electronic trip units,
current sensors and integral ground
fault protection. The three-phase sensors
are required for normal phase overcurrent protection. Ground fault sensing
is obtained with the addition of an
identically rated sensor mounted on the
Typical
4W Load
As an example, one of the more

frequently used systems where
continuity of service to critical loads
is a factor is the dual source system
illustrated in Figure 1.4-8. This system
uses tie-point grounding as permitted
under NEC Sec. 250.24(A)(3). The use
of this grounding method is limited
to services that are dual fed (doubleended) in a common enclosure or
grouped together in separate enclosures, employing a secondary tie.
Figure 1.4-7. Residual Sensing Method

As with the zero sequence sensing
method, the resultant residual sensor
output to the ground fault relay or
integral ground fault tripping circuit
will be zero if all currents flow only
in the circuit conductors. Should a
ground fault occur, the current from
the faulted conductor will return along
the ground path, rather than on the
other circuit conductors, and the residual sum of the sensor outputs will not
be zero. When the level of ground fault
current exceeds the pre-set current
and time delay settings, a ground
fault tripping action will be initiated.
This scheme uses individual sensors

connected in ground return fashion.
Under tie breaker closed operating
conditions, either the M1 sensor or
M2 sensor could see neutral unbalance
currents and possibly initiate an
improper tripping operation. However,
with the polarity arrangements of
these two sensors along with the tie
breaker auxiliary switch (T/a) and
interconnections as shown, this
possibility is eliminated.
This method of sensing ground faults

can be economically applied on main
service disconnects where circuit breakers with integral ground fault protection
are provided. It can be used in protection schemes per NEC (230.95) or in
multi-tier schemes where additional
Power
Transformer
Power
Transformer
Neutral Sensor
Main Bkr. 52-1
Main
Bkr.
52-1
Neutral Sensor
Main Bkr. 52-2
Tie Bkr.
52-T
A, B, C
Neutral
Typical
4-Wire
Feeder
Neutral Sensor
Tie Bkr. 52-T
( )B5
( )B4
4-Wire
Load
B4
B5
Digitrip
Main
Bkr.
52-2
A, B, C
Neutral
M1N
M1G
Typical
Feeder
GFR
52-T
a
TN
GFR
TG
M2G
M2N
3352-T
B5
B4
Digitrip
Main Bkr.
52-1
B4
B5
Digitrip
Main Bkr.
52-T
( )B5
Typical
52-T 4-Wire
Feeder
a
B4
B5
Digitrip
Main Bkr.
52-2
( )B4
4-Wire
Load
B4
B5
Digitrip
Figure 1.4-8. Dual Source SystemSingle Point Grounding

Note: This GF scheme requires trip units to be set to source ground sensing.
CA08104001E

April 2016
1.4-13
Sheet 01 069

Selective ground fault tripping coordination between the tie breaker and the
two main circuit breakers is achieved
by pre-set current pickup and time
delay settings between devices GFR/1,
GFR/2 and GFR/T.
or a combination of all types may be

employed to accomplish the desired
end results.
Because the NEC (230.95) limits the
maximum setting of the ground fault
protection used on service equipment
to 1200 A (and timed tripping at 3000 A
for one second), to prevent tripping
of the main service disconnect on a
feeder ground fault, ground fault
protection must be provided on all the
feeders. To maintain maximum service
continuity, more than two levels (zones)
of ground fault protection will be
required, so that ground fault outages
can be localized and service interruption minimized. To obtain selectivity
between different levels of ground
fault relays, time delay settings should
be employed with the GFR furthest
downstream having the minimum
time delay. This will allow the GFR
nearest the fault to operate first.
With several levels of protection, this
will reduce the level of protection for
faults within the upstream GFR zones.
Zone interlocking was developed for
GFRs to overcome this problem.
The advantages of increased service

continuity offered by this system can
only be effectively used if additional
added on each downstream feeder.
Some users prefer individual grounding
of the transformer neutrals. In such
cases, a partial differential ground fault
scheme should be used for the mains
and tie breaker.
An example of a residual partial differential scheme is shown in Figure 1.4-9.
The scheme typically relies upon the
vector sum of at least two neutral
sensors in combination with each
breakers three-phase sensors. To
reduce the complexity of the drawing,
each of the breakers three-phase
sensors have not been shown. It is
absolutely critical that the sensors
polarities are supplied as shown, the
neutral sensor ratings of the mains and
tie are the same, and that there are
no other grounds on the neutral bus
made downstream of points shown.
GFRs (or circuit breakers with integral

ground fault protection) with zone
interlocking are coordinated in a
system to operate in a time delayed
mode for ground faults occurring most
remote from the source. However, this
time delayed mode is only actuated
when the GFR next upstream from the
fault sends a restraining signal to the
upstream GFRs. The absence of a
restraining signal from a downstream
An infinite number of ground fault

protection schemes can be developed
depending upon the number of alternate
sources, the number of grounding points
and system interconnections involved.
Depending upon the individual system
configuration, either mode of sensing
Power
Transformer
Power
Transformer
X
X
Neutral
Sensor Main
Breaker 52-2
Neutral
Sensor Main
Breaker 52-1
Main
Breaker
52-1
Typical
Four-Wire
Feeder
Trip Unit
Phase A,
Phase B,
Phase C
Neutral
Neutral Sensor X
Tie Breaker 52-T
X
X
52-1
a
52-T
a
Main
Breaker
52-2
52-2
a
Typical
Four-Wire
Feeder
Trip Unit
Main Breaker
52-1
X
X
Trip Unit
Trip Unit
Tie Breaker Main Breaker
52-T
52-2
Figure 1.4-9. Dual Source SystemMultiple Point Grounding

CA08104001E
Power distribution systems differ

widely from each other, depending
upon the requirements of each user,
and total system overcurrent protection, including ground fault currents,
must be individually designed to meet
these needs. Experienced and knowledgeable engineers must consider the
power sources (utility or on-site), the
effects of outages and costs of downtime, safety for people and equipment,
initial and lifecycle costs, and many
other factors. They must apply protective devices, analyzing the time-current
characteristics, fault interrupting
capacity, and selectivity and coordination methods to provide the most safe
and cost-effective distribution system.
Four-Wire Load
Four-Wire Load
Circuit breakers with integral ground

fault protection and standard circuit
breakers with shunt trips activated
by the ground fault relay are ideal for
ground fault protection. Many fused
switches over 1200 A, and Eaton Type
FDP fusible switches with ratings
from 400 to 1200 A, are listed by UL
as suitable for ground fault protection.
Fusible switches so listed must be
equipped with a shunt trip, and be able
to open safely on faults up to 12 times
their rating.
Further Information
Phase A,
Phase B,
Phase C
Neutral
Tie Breaker
52-T
Trip Unit
GFR is an indication that any occurring

ground fault is within the zone of the
GFR next upstream from the fault and
that device will operate instantaneously
to clear the fault with minimum damage and maximum service continuity.
This operating mode permits all GFRs
to operate instantaneously for a fault
within their zone and still provide
complete selectivity between zones.
The National Electrical Manufacturers
Association (NEMA) states, in their
application guide for ground fault
protection, that zone interlocking is
necessary to minimize damage from
ground faults. A two-wire connection
is required to carry the restraining
signal from the GFRs in one zone to
the GFRs in the next zone.
PRSC-4ESystem Neutral Grounding and Ground Fault Protection

(ABB Publication)
PB 2.2NEMA Application Guide
for Ground Fault Protective Devices
for Equipment
IEEE Standard 142Grounding of
Industrial and Commercial Power
Systems (Green Book)
IEEE Emerald Book (Standard 1100)
UL 96A, Installation Requirements
for Lightning Protection Systems
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21

April 2016
Sheet 01 070
i
ii
1
2
3
Lightning and Surge Protection

Physical protection of buildings
from direct damage from lightning
is beyond the scope of this section.
Requirements will vary with geographic
location, building type and environment, and many other factors (see
IEEE/ANSI Standard 142, Grounding
of Industrial and Commercial Power
Systems). Any lightning protection
system must be grounded, and the
lightning protection ground must be
bonded to the electrical equipment
grounding system.
Grounding Electrodes
At some point, the equipment and

system grounds must be connected
to the earth by means of a grounding
electrode system.
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Outdoor substations usually use a

ground grid, consisting of a number of
ground rods driven into the earth and
bonded together by buried copper
conductors. The required grounding
electrode system for a building is
spelled out in the NEC Article 250.
The preferred grounding electrode
is a metal underground water pipe in
direct contact with the earth for at least
10 ft (3 m). However, because underground water piping is often plastic
outside the building, or may later be
replaced by plastic piping, the NEC
requires this electrode to be supplemented by and bonded to at least one
other grounding electrode, such as
the effectively grounded metal frame
of the building, a concrete-encased
electrode, a copper conductor ground
ring encircling the building, or a made
electrode such as one or more driven
ground rods or a buried plate. Where
any of these electrodes are present,
they must be bonded together into one
grounding electrode system.
One of the most effective grounding
electrodes is the concrete-encased
electrode, sometimes called the Ufer
ground, named after the man who
developed it. It consists of at least
20 ft (6 m) of steel reinforcing bars or
rods not less than 1/2 inches (12.7 mm)
in diameter, or at least 20 ft (6 m) of
bare copper conductor, size No. 4 AWG
or larger, encased in at least 2 inches
(50.8 mm) of concrete. It must be
located within and near the bottom of
a concrete foundation or footing that
is in direct contact with the earth. Tests
have shown this electrode to provide
a low-resistance earth ground even in
poor soil conditions.
The electrical distribution system and

equipment ground must be connected
to this grounding electrode system by
a grounding electrode conductor. All
other grounding electrodes, such as
those for the lightning protection system, the telephone system, television
antenna and cable TV system grounds,
and computer systems, must be bonded
to this grounding electrode system.
Medium Voltage Equipment Surge

Protection Considerations
Transformers
If the voltage withstand/BIL rating of
the transformer is less than that of the
switchgear feeding the transformer,
surge protection is recommended at
the transformer terminals, in line with
established practices. In addition,
consideration should be given to using
surge arresters and/or surge capacitors
for transformers having equal or
greater withstand/BIL ratings than that
of the switchgear feeding the transformer for distribution systems where
reflected voltage waves and/or resonant conditions may occur. Typically
incoming voltage surges are reflected
at the transformer primary terminals
(because of the change in impedance)
resulting in voltages at the ends of the
transformer primary terminals/windings of up to two times the incoming
voltage wave. System capacitance and
inductance values combined with the
transformer impedance values can
cause resonant conditions resulting
in amplified reflected waves. Surge
arresters/capacitors when required,
should be located as close to the transformer primary terminals as practical.
Motors
Surge capacitors and, where appropriate, surge arresters should be applied
at the motor terminals.
Generators
Surge capacitors and station
class surge arresters at the machine
terminals.
Surge Protection
Eatons VacClad-W metal-clad switchgear is applied over a broad range of
circuits, and is one of the many types
of equipment in the total system. The
distribution system can be subject to
voltage transients caused by lighting
or switching surges.
Recognizing that distribution system
can be subject to voltage transients
caused by lighting or switching, the
industry has developed standards to
provide guidelines for surge protection
of electrical equipment. Those guidelines should be used in design and
protection of electrical distribution
systems independent of the circuit
breaker interrupting medium. The
industry standards are:
ANSI C62
Guides and Standards for Surge
Protection
IEEE 242Buff Book
IEEE Recommended Practice for
Protection and Coordination of
Systems
IEEE 141Red Book
Recommended Practice for
Electric Power Distribution for
Industrial Plants
IEEE C37.20.2
Standards for Metal-Clad Switchgear
Eatons medium voltage metal-clad
and metal-enclosed switchgear that
uses vacuum circuit breakers is applied
over a broad range of circuits. It is one
of the many types of equipment in the
total distribution system. Whenever a
switching device is opened or closed,
certain interactions of the power
system elements with the switching
device can cause high frequency voltage
transients in the system. Due to the
wide range of applications and variety
of ratings used for different elements
in the power systems, a given circuit
may or may not require surge protection. Therefore, Eaton does not include
surge protection as standard with its
metal-clad or metal-enclosed medium
voltage switchgear. The user exercises
the options as to the type and extent
of the surge protection necessary
depending on the individual circuit
characteristics and cost considerations.
The following are Eatons recommendations for surge protection of medium
voltage equipment. Please note these
recommendations are valid when
using Eatons vacuum breakers only.
21
CA08104001E
April 2016

1.4-15
Sheet 01 071

Surge Protection Recommendations
Note: The abbreviation ZORC used in the
text below refers to Surge Protection Device
manufactured by Strike Technology (Pty)
Ltd. An equivalent device offered by other
manufacturers, such as Type EHZ by ABB,
and Protec Z by Northern Technologies SA
can also be used.
1. For circuits exposed to lightning,

surge arresters should be applied
in line with Industry standard
practices.
2. Transformers
a. Close-Coupled to medium
voltage primary breaker:
Provide transients surge protection, such as Surge Arrester
in parallel with RC Snubber, or
ZORC. The surge protection
device selected should be
located and connected at the
transformer primary terminals
or it can be located inside the
switchgear and connected on
the transformer side of the
primary breaker.
b. Cable-Connected to medium
voltage primary breaker:
Provide transient surge protection, such as Surge Arrester in
parallel with RC Snubber, or
ZORC for transformers connected by cables with lengths
up to 75 feet. The surge protection device should be located
and connected at the transformer
terminals. No surge protection
is needed for transformers with
lightning impulse withstand
ratings equal to that of the
switchgear and connected to
the switchgear by cables at
least 75 feet or longer. For
transformers with lower BIL,
provide surge arrester in parallel
with RC Snubber or ZORC.
RC Snubber and/or ZORC damp

internal transformer resonance:
The natural frequency of transformer
windings can under some circumstances
be excited to resonate. Transformer
windings in resonance can produce
elevated internal voltages that produce
insulation damage or failure. An RC
Snubber or a ZORC applied at the
transformer terminals as indicated
above can damp internal winding
resonance and prevent the production
of damaging elevated internal voltages.
This is typically required where rectifiers,
UPS or similar electronic equipment is
on the transformer secondary.
3. Arc-Furnace Transformers
Provide Surge Arrester in parallel
with RC Snubber, or ZORC at the
transformer terminals.
4. MotorsProvide Surge Arrester in
parallel with RC Snubber, or ZORC
at the motor terminals. For those
motors using VFDs, surge protection should be applied and precede
the VFD devices as well.
5. GeneratorsProvide station class
Surge Arrester in parallel with RC
Snubber, or ZORC at the generator
terminals.
6. Capacitor SwitchingNo surge

protection is required. Make sure
that the capacitors lightning
impulse withstand rating is equal
to that of the switchgear.
7. Shunt Reactor Switching
reactor terminals.
8. Motor Starting Reactors or Reduced
Voltage Auto-Transformers
reactor or RVAT terminals.
i
ii
1
2
3
9. Switching Underground Cables

Surge protection not needed.
Types of Surge Protection Devices
Generally surge protective devices

should be located as closely as possible
to the circuit component(s) that require
protection from the transients, and
connected directly to the terminals of
the component with conductors that
are as short and flat as possible to
minimize the inductance. It is also
important that surge protection devices
should be properly grounded for
effectively shunting high frequency
transients to ground.
6
7
8
9
10
11
12
13
Figure 1.4-10. Surge Protection Devices
14
15
16
17
18
19
20
21
CA08104001E

April 2016
Sheet 01 072
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Surge Arresters
Surge Capacitors
ZORC
The modern metal-oxide surge

arresters are recommended because
this latest advance in arrester design
ensures better performance and high
reliability of surge protection schemes.
Manufacturers technical data must
be consulted for correct application
of a given type of surge arrester.
Notice that published arrester MCOV
(Maximum Continuous Operating
Voltage) ratings are based on 40 or
45 C ambient temperature. In general,
the following guidelines are recommended for arrester selections, when
installed inside Eatons medium
voltage switchgear:
Metal-oxide surge arresters limit the

magnitude of prospective surge overvoltage, but are ineffective in controlling its rate of rise. Specially designed
surge capacitors with low internal
inductance are used to limit the rate of
rise of this surge overvoltage to protect
turn-to-turn insulation. Recommended
values for surge capacitors are: 0.5 f
on 5 and 7.5 kV, 0.25 f on 15 kV, and
0.13 f on systems operating at 24 kV
and higher.
A ZORC device consists of parallel

combination of Resistor (R) and Zinc
Oxide Voltage Suppressor (ZnO), connected in series with a Surge Capacitor.
The resistor R is sized to match surge
impedance of the load cables, typically
20 to 30 ohms. The ZnO is a gapless
metal-oxide nonlinear arrester, set
to trigger at 1 to 2 PU voltage, where
1 PU = 1.412*(VL-L/1.732). The Surge
Capacitor is typically sized to be 0.15 to
0.25 microfarad. As with RC Snubber,
under normal operating conditions,
impedance of the capacitor is very
high, effectively isolating the resistor
R and ZnO from the system at normal
power frequencies, and minimizing
heat dissipation during normal operation. Under high frequency transient
conditions, the capacitor offers very
low impedance, thus effectively
inserting the resistor R and ZnO in
the power system as cable terminating
network, thus minimizing reflection of
the steep wave-fronts of the voltage
transients and prevents voltage doubling of the traveling wave. The ZnO
element limits the peak voltage magnitudes. The combined effects of R, ZnO,
and Capacitor of the ZORC device
provides optimum protection against
high frequency transients by absorbing,
damping, and by limiting the peak
amplitude of the voltage wave-fronts.
Please note that the ZORC is not a
lightning protection device. If lightning
can occur or be induced in the electrical
system, a properly rated and applied
surge arrester must precede the ZORC.
A. Solidly Grounded Systems:

Arrester MCOV rating should be
equal to 1.05 x VLL/(1.732 x T),
where VLL is nominal line-to-line
service voltage, 1.05 factor allows
for +5% voltage variation above
the nominal voltage according
to ANSI C84.1, and T is derating
factor to allow for operation at
55 C switchgear ambient, which
should be obtained from the
arrester manufacturer for the type
of arrester under consideration.
Typical values of T are: 0.946 to 1.0.
B. Low Resistant Grounded Systems
(systems grounded through
resistor rated for 10 seconds):
Arrester 10-second MCOV capability
at 60 C, which is obtained from
manufacturers data, should be
equal to 1.05 x VLL, where VLL is
nominal line-to-line service voltage,
and 1.05 factor allows for +5%
voltage variation above the
nominal voltage.
C. Ungrounded or Systems
Grounded through impedance
other than 10-second resistor:
Arrester MCOV rating should be
equal to 1.05 x VLL/T, where VLL
and T are as defined above.
RC Snubber
A RC Snubber device consists of a
non-inductive resistor R sized to match
surge impedance of the load cables,
typically 20 to 30 ohms, and connected
in series with a Surge Capacitor C. The
Surge Capacitor is typically sized to be
0.15 to 0.25 microfarad. Under normal
operating conditions, impedance of
the capacitor is very high, effectively
isolating the resistor R from the
system at normal power frequencies,
and minimizing heat dissipation during
normal operation. Under high frequency
transient conditions, the capacitor
offers very low impedance, thus effectively inserting the resistor R in the
power system as cable terminating
resistor, thus minimizing reflection of
the steep wave-fronts of the voltage
transients and prevents voltage doubling of the traveling wave. The RC
Snubber provides protection against
high frequency transients by absorbing and damping and the transients.
Please note RC Snubber is most effective in mitigating fast-rising transient
voltages, and in attenuating reflections
and resonances before they have a
chance to build up, but does not limit
the peak magnitude of the transient.
Therefore, the RC Snubber alone may
not provide adequate protection. To
limit peak magnitude of the transient,
application of surge arrester should
also be considered.
Refer to Table 1.4-3 for recommended

ratings for metal-oxide surge arresters
that are sized in accordance with the
above guidelines, when located in
Eatons switchgear.
18
19
20
21
CA08104001E

April 2016
1.4-17
Sheet 01 073
Surge Protection Summary
Good protection: Surge Arrester

in parallel with Surge Capacitor for
protection from high overvoltage
peaks and fast rising transient. This
option may not provide adequate
surge protection from escalating
voltages caused by circuit resonance.
When applying surge capacitors on
both sides of a circuit breaker, surge
capacitor on one side of the breaker
must be RC Snubber or ZORC,
to mitigate possible virtual
current chopping.
Minimum protection: Surge Arrester

for protection from high overvoltage
peaks, or Surge Capacitor for protection from fast-rising transient. Please
note that the surge arresters or surge
capacitor alone may not provide
adequate surge protection from
escalating voltages caused by circuit
resonance. Note that when applying
surge capacitors on both sides of a
circuit breaker, surge capacitor on
one side of the breaker must be
RC Snubber or ZORC, to mitigate
possible virtual current chopping.
Best protection: ZORC, plus proper

surge arrester preceding ZORC where
needed for protection against lightning.
ZORC provides protection from high
frequency voltage transients and limits
peak magnitude of the transient to
1 to 2 PU (see ZORC description on
Page 1.4-16 for more detail). Surge
arrester provides protection from
higher voltage peaks resulting from
lightning surges.
Further Information
IEEE/ANSI Standard 142Grounding

Systems (Green Book)
IEEE Standard 241Electric Power
Systems in Commercial Buildings
(Gray Book)
IEEE Standard 141Electric Power
Distribution for Industrial Plants
(Red Book)
Better protection: RC Snubber in

parallel with Surge Arrester for
protection from high frequency
transients and voltage peaks.
i
ii
1
2
3
4
5
6
Table 1.4-3. Surge Arrester SelectionsRecommended Ratings

Service
Voltage
Line-to-Line
kV
Distribution Class Arresters

Solidly
Grounded System
Station Class Arresters
Low Resistance
Grounded System
High Resistance or
Solidly
Ungrounded System Grounded System
Nominal
Nominal
Arrester Ratings kV
Nominal
MCOV
Low Resistance
Grounded System
High Resistance or
Ungrounded System
Nominal
Nominal
Arrester Ratings kV
MCOV
MCOV
Nominal
MCOV
MCOV
MCOV
7
8
2.30
2.40
3.30
3
3
3
2.55
2.55
2.55
3
3
3
2.55
2.55
2.55
3
6
6
2.55
5.10
5.10
3
3
3
2.55
2.55
2.55
3
3
3
2.55
2.55
2.55
3
6
6
2.55
5.10
5.10
4.00
4.16
4.76
3
6
6
2.55
5.10
5.10
6
6
6
5.10
5.10
5.10
6
6
9
5.10
5.10
7.65
3
6
6
2.55
5.10
5.10
6
6
6
5.10
5.10
5.10
6
6
9
5.10
5.10
7.65
10
4.80
6.60
6.90
6
6
6
5.10
5.10
5.10
6
6
6
5.10
5.10
5.10
9
9
9
7.65
7.65
7.65
6
6
6
5.10
5.10
5.10
7.20
8.32
8.40
11.00
11.50
12.00
6
9
9
9
9
10
5.10
7.65
7.65
7.65
7.65
8.40
6
9
9
9
10
10
5.10
7.65
7.65
7.65
8.40
8.40
10
12
12
15
18
18
8.40
10.20
10.20
12.70
15.30
15.30
6
9
9
9
9
10
5.10
7.65
7.65
6
6
9
9
9
9
5.10
5.10
7.65
7.65
7.65
7.65
9
9
9
10
12
12
7.65
7.65
7.65
8.40
10.20
10.20
7.65
7.65
8.40
10
12
12
8.40
10.20
10.20
15
18
18
12.70
15.30
15.30
12.47
13.20
13.80
10
12
12
8.40
10.20
10.20
12
12
12
10.20
10.20
10.20
18
18
18
15.30
15.30
15.30
10
12
12
8.40
10.20
10.20
12
12
15
10.20
10.20
12.70
18
18
18
15.30
15.30
15.30
14.40
18.00
20.78
22.00
22.86
23.00
12
15
18
18
18
18
10.20
12.70
15.30
15.30
15.30
15.30
12
15
18
18
21
21
10.20
12.70
15.30
15.30
17.00
17.00
21
27
30
30
17.00
22.00
24.40
24.40
12
15
18
18
18
18
10.20
12.70
15.30
15.30
15.30
15.30
15
18
21
21
24
24
12.70
15.30
17.00
17.00
19.50
19.50
21
27
30
30
36
36
17.00
22.00
24.40
24.40
29.00
29.00
24.94
25.80
26.40
21
21
21
17.00
17.00
17.00
24
24
24
19.50
19.50
19.50
21
21
21
17.00
17.00
17.00
24
24
27
19.50
19.50
22.00
36
36
39
29.00
29.00
31.50
16
33.00
34.50
38.00
27
30
30
22.00
24.40
24.40
30
30
24.40
24.40
27
30
30
22.00
24.40
24.40
36
36
36
29.00
29.00
29.00
45
48
36.50
39.00
17
11
12
13
14
15
18
19
20
21
CA08104001E

April 2016
Sheet 01 074
Power Quality
Power Quality Terms

Technical Overview
ii
Introduction
Sensitive electronic loads deployed

today by users require strict requirements for the quality of power delivered
to loads.
2
3
4
5
6
7
8
9
10
11
12
For electronic equipment, power

disturbances are defined in terms of
amplitude and duration by the electronic equipment operating envelope.
Electronic loads may be damaged
and disrupted, with shortened life
expectancy, by disturbances.
The proliferation of computers, variable
frequency motor drives, UPS systems
and other electronically controlled
equipment is placing a greater demand
on power producers for a disturbancefree source of power. Not only do these
types of equipment require quality
power for proper operation; many
times, these types of equipment are
also the sources of power disturbances
that corrupt the quality of power in a
given facility.
Power quality is defined according
to IEEE Standard 1100 as the concept
of powering and grounding electronic
equipment in a manner that is suitable
to the operation of that equipment.
IEEE Standard 1159 notes that within
the industry, alternate definitions or
interpretations of power quality have
been used, reflecting different points
of view.
15
In addressing power quality problems

at an existing site, or in the design
stages of a new building, engineers
need to specify different services or
mitigating technologies. The lowest
cost and highest value solution is
to selectively apply a combination
of different products and services
as follows:
16
Key services/technologies in the

power quality industry:
13
14
17
18
19
20
Power quality surveys, analysis

and studies
Power monitoring
Grounding products and services
Surge protection
Voltage regulation
Harmonic solutions
Lightning protection (ground rods,
hardware, etc.)
Uninterruptible power supply (UPS)
or motor-generator (M-G) set
Defining the Problem

Power quality problems can be resolved
in three ways: by reducing the variations
in the power supply (power disturbances), by improving the load equipments tolerance to those variations, or
by inserting some interface equipment
(known as power conditioning equipment) between the electrical supply
and the sensitive load(s) to improve the
compatibility of the two. Practicality
and cost usually determine the extent
to which each option is used.
Many methods are used to define
power quality problems. For example,
one option is a thorough on-site
investigation, which includes inspecting
wiring and grounding for errors,
monitoring the power supply for
power disturbances, investigating
equipment sensitivity to power disturbances, and determining the load
disruption and consequential effects
(costs), if any. In this way, the power
quality problem can be defined,
alternative solutions developed,
and optimal solution chosen.
Before applying power-conditioning
equipment to solve power quality
problems, the site should be checked
for wiring and grounding problems.
Sometimes, correcting a relatively
inexpensive wiring error, such as a
loose connection or a reversed neutral
and ground wire, can avoid a more
expensive power conditioning solution.
Sometimes this approach is not practical
because of limitations in time; expense
is not justified for smaller installations;
monitoring for power disturbances
may be needed over an extended
period of time to capture infrequent
disturbances; the exact sensitivities of
the load equipment may be unknown
and difficult to determine; and finally,
the investigative approach tends to
solve only observed problems. Thus
unobserved or potential problems may
not be considered in the solution. For
instance, when planning a new facility,
there is no site to investigate. Therefore, power quality solutions are often
implemented to solve potential or perceived problems on a preventive basis
instead of a thorough on-site investigation.
Another option is to buy power conditioning equipment to correct any and

all perceived power quality problems
without any on-site investigation.
Power Quality Terms

Power disturbance: Any deviation
from the nominal value (or from some
selected thresholds based on load
tolerance) of the input AC power
characteristics.
Total harmonic distortion or distortion
factor: The ratio of the root-meansquare of the harmonic content to the
root-mean-square of the fundamental
quantity, expressed as a percentage
of the fundamental.
Crest factor: Ratio between the
peak value (crest) and rms value of
a periodic waveform.
Apparent (total) power factor: The
ratio of the total power input in watts
to the total volt-ampere input.
Sag: An rms reduction in the AC
voltage, at the power frequency, for
the duration from a half-cycle to a few
seconds. An undervoltage would have
a duration greater than several seconds.
Interruption: The complete loss of voltage for a time period.
Transient: A sub-cycle disturbance
in the AC waveform that is evidenced
by a sharp brief discontinuity of the
waveform. May be of either polarity
and may be additive to or subtractive
from the nominal waveform.
Surge or impulse: See transient.
Noise: Unwanted electrical signals
that produce undesirable effects
in the circuits of control systems
in which they occur.
Common-mode noise: The noise
voltage that appears equally and in
phase from each current-carrying
conductor to ground.
Normal-mode noise: Noise signals
measurable between or among active
circuit conductors feeding the subject
load, but not between the equipment
grounding conductor or associated
signal reference structure and the active
circuit conductors.
21
CA08104001E
April 2016

1.4-19
Sheet 01 075
Power Quality
Methodology for Ensuring Effective
Power Quality to Electronic Loads
Cost Per kVA
The power quality pyramid is an

effective guide for addressing power
quality problems at an existing facility.
The framework is also effective for
specifying engineers who are designing a new facility. Power quality starts
with grounding (the base of the
pyramid) and then moves upward
to address the potential issues. This
simple, yet proven methodology,
will provide the most cost-effective
approach. As we move higher up the
pyramid, the cost per kVA of mitigating
potential problems increase and the
quality of the power increases (refer
to Figure 1.4-11).
5. Uninterruptible Power Supply

(UPS, Gen. Sets, etc.)
4. Harmonic Distortion
3. Voltage Regulation
2. Surge Protection
1. Grounding
The proliferation of communication

and computer network systems
has increased the need for proper
grounding and wiring of AC and data/
communication lines. In addition to
reviewing AC grounding and bonding
practices, it is necessary to prevent
ground loops from affecting the signal
reference point.
The benefit of implementing cascaded

network protection is shown in
Figure 1.4-12. Combined, the two
stages of protection at the service
entrance and branch panel locations
reduce the IEEE 62.41 recommended
test wave (C320 kV, 10 kA) to less than
200 V voltage, a harmless disturbance
level for 120 V rated sensitive loads.
2. Surge Protection
If only building entrance feeder

protection were provided, the letthrough voltage will be approximately
950 V in a 277/480 V system exposed
to induced lightning surges. This
level of let-through voltage can cause
degradation or physical damage of
most electronic loads.
Wherever possible, consultants,

specifiers and application engineers
should ensure similar loads are fed
from the same source. In this way,
disturbance-generating loads are
separated from electronic circuits
affected by power disturbances. For
example, motor loads, HVAC systems
and other linear loads should be
separated from the sensitive process
control and computer systems.
The most effective and economic

solution for protecting a large number
of loads is to install parallel SPDs at
the building service entrance feeder
and panelboard locations. This reduces
the cost of protection for multiple
sensitive loads.
Surge protection devices (SPDs)

are recommended as the next stage
power quality solutions. NFPA,
UL 96A, IEEE Emerald Book and
equipment manufacturers recommend the use of surge protectors.
The SPD shunt short duration voltage
disturbances to ground, thereby
preventing the surge from affecting
electronic loads. When installed as
part of the facility-wide design, SPDs
are cost-effective compared to all
other solutions (on a $/kVA basis).
The IEEE Emerald Book recommends
the use of a two-stage protection
concept. For large surge currents,
diversion is best accomplished in
two stages: the first diversion should
be performed at the service entrance
to the building. Then, any residual
voltage resulting from the action
can be dealt with by a second
protective device at the power
panel of the computer room
(or other critical loads).
Figure 1.4-11. Power Quality Pyramid
1. Grounding
SPD
480V
Stage 1 Protection
(Service Entrance)
SPD
120/208V
Computer or
Sensitive
Loads
Stage 2 Protection
(Branch Location)
System Test Parameters:

IEEE C62.41[10] and C62.45 [10]
test procedures using category;
480V main entrance panels;
100 ft (30m) of three-phase wire;
480/208V distribution transformer;
and 208V branch panel.
20,000V
PEAK VOLTAGE
CP
Grounding represents the foundation

of a reliable power distribution
system. Grounding and wiring
problems can be the cause of up to
80% of all power quality problems.
All other forms of power quality
solutions are dependent upon good
grounding procedures.
= SPD
Figure 1.4-12. Cascaded Network Protection
Inputhigh energy
transient disturbance; IEEE Category
C3 Impulse 20,000V; 10,000A
Best achievable
performance with single SPD
at main panel (950V, at Stage 1)
800V
i
ii
1
3
4
6
7
8
10
11
12
13
14
15
400V
0
25 uS
50 uS
TIME (MICROSECONDS)
Two stage (cascade

approach) achieves best
possible protection (less
than 200V at Stage 2)
16
17
18
19
20
21
CA08104001E

April 2016
Sheet 01 076
Power Quality
The recommended system approach

for installing SPDs is summarized in
Figure 1.4-13.
ii
Building entrance SPDs protect

the facility against large external
transients, including lightning
SPDs are bi-directional and prevent
transient and noise disturbances
from feeding back within a system
when installed at distribution or
branch panels
Two levels of protection safeguard
sensitive loads from physical
damage or operational upset
1.
Identify Critical Loads
1
2.
Identify Non-Critical Loads
2
3
3.
Identify Noise and
Disturbance Generating Loads
4.
Review Internal Power Distribution Layout
5.
Identify Facility Exposure to
Expected Levels of Disturbance
Directly connecting the surge suppresser to the busbar of electrical

distribution equipment results in
the best possible level of protection.
Compared to side-mounted devices,
connecting the SPD unit to the busbar
eliminates the need for lead wires
and reduces the let-through voltage
up to 50% (see Figure 1.4-14).
8
Figure 1.4-13. System Approach for Installing SPDs
9
10
There may be specific critical loads

within a facility that require a higher
level of protection. A series SPD is best
suited for protecting such loads.
Advantages of the system approach are:
11
The lowest possible investment

in mitigating equipment to protect
a facility
Increasing the diameter of the installation

wires is of negligible benefit. Inductance is a skin effect phenomenon and
a function of wire circumference. Since
only a marginal reduction in inductance
is achieved when the diameter of the
installation conductors is increased,
the use of large diameter wire results
in only minimal improvement (see
Figure 1.4-15).
Side-Mounted SPD vs. Integral SPD
6.
Apply Mitigating Equipment to:
a) Service Entrance Main Panels
b) Key Sub-Panels
c) Critical Loads
d) Data and Communication Lines
By twisting the installation wires, the

area between wires is reduced and the
mutual inductance affect minimized.
Further benefits provided by integrated

surge suppression designs are the
elimination of field installation costs and
the amount of expensive outboard
wall space taken up by side-mounted
SPD devices.
Building Entrance Feeder Installation

Considerations
Given that surges are high frequency

disturbances, the inductance of the
installation wiring increases the
let-through voltage of the protective
device. Figure 1.4-15 shows that
for every inch of lead length, the
let-through voltage is increased by
an additional 1525 V above the
manufacturers stated suppression
performance.
Installing an SPD device immediately

after the switchgear or switchboard
main breaker is the optimal location
for protecting against external disturbances such as lightning. When placed
in this location, the disturbance is
intercepted by the SPD and reduced
to a minimum before reaching the
distribution and/or branch panel(s).
The use of a disconnect breaker
eliminates the need to de-energize
the building entrance feeder equipment should the SPD fail or require
isolation for Megger testing.
Lead length has the greatest effect on

the actual level of protection realized.
Twisting of the installation wires is
the second most important installation
consideration.
12
208Y/120 Panelboard
(integrated versus side mounted SPD)
13
SPD Integrated
into Panelboards,
Switchboards, MCCs
Side-Mounted SPD
used for Retrofit
Applications
15
16
SPD
SPD
17
GRO UND
18
19
G RO UND
Let-Through Voltage at Bus Bar
1000
14
Side-Mounted SPD Device

(assuming 14-inch (355.6 mm) lead length to bus)
800
600
400
Integrated SPD
(direct bus bar connection)
200
0
200
2.00
Surge
Event
0.00
2.00
4.00
6.00
8.00
10.00
Microseconds
Figure 1.4-14. Performance Comparison of Side-Mounted vs. Integrated SPD
20
21
CA08104001E

April 2016
1.4-21
Sheet 01 077
Additional Let-Through Voltage
Power Quality
Reference Tab 34 for detailed
information on SPDs.
Additional Let-Through Voltage Using IEEE C1(6000V, 3000A)[3]

Waveform (UL 1449 Test Wave)[12]
900
800
700
600
500
400
300
200
100
0
209V (23%)
673V (75%)
3 ft (914.4 mm)
Lead Length
Loose Wiring
Twisted Wires
14 AWG
10 AWG
4 AWG
1 ft (304.8 mm)
Lead Length,
Twisted Wires
Figure 1.4-15. The Effect of Installation Lead Length on Let-Through Voltage

1
Additional to UL 1449 ratings.
The size or capacity of a suppressor is

measured in surge current per phase.
Larger suppressers rated at approximately 250 kA per phase should be
installed at the service entrance to
survive high-energy surges associated
with lightning.
A 250 kA per phase surge rating allows
for over a 25-year life expectancy
assuming an IEEE defined high
exposure environment. Lower surge
rating devices may be used; however,
device reliability and long-term
performance may be compromised.
For aerial structures, the 99.8 percentile
recorded lightning stroke current is
less than 220 kA. The magnitude of
surges conducted or induced into a
facility electrical distribution system is
considerably lower given the presence
of multiple paths for the surge to travel
along. It is for this reason that IEEE
C62.41 recommends the C3 (20 kV,
10 kA) test wave for testing SPDs
installed at building entrance feeders.
SPDs with surge ratings greater than
250 kA are not required, however,
higher ratings are available and may
provide longer life.
Installing Panelboard Surge

Protection Devices
Smaller surge capacity SPDs (120 kA
per phase) are installed at branch panelboards where power disturbances
are of lower energy, but occur much
more frequently. This level of surge
current rating should result in a
greater than 25-year life expectancy.
When isolated ground systems are
used, the SPD should be installed such
that any common mode surges are
shunted to the safety ground.
The use of a disconnect breaker is
optional. The additional let-through
voltage resulting from the increased
inductance caused by the disconnect
switch is about 5060 V.
CA08104001E
This increase in disturbance voltage

can result in process disruption
and downtime.
3. Voltage Regulation
Voltage regulation (i.e., sags or overvoltage) disturbances are generally
site- or load-dependent. A variety of
mitigating solutions are available
depending upon the load sensitivity,
fault duration/magnitude and the
specific problems encountered. It is
recommended to install monitoring
equipment on the AC power lines to
assess the degree and frequency of
occurrences of voltage regulation
problems. The captured data will allow
for the proper solution selection.
4. Harmonics Distortion
Installing Dataline Surge Protection
Harmonics and Nonlinear Loads
Most facilities also have communication lines that are potential sources
for external surges. As identified by
the power quality pyramid, proper
grounding of communication lines is
essential for dependable operation.
NEC Article 800 states that all data,
power and cable lines be grounded
and bonded.
Until recently, most electrical loads were

linear. Linear loads draw the full sine
wave of electric current at its 60 cycle
(Hz) fundamental frequencyFigure
1.4-16 shows balance single-phase,
linear loads. As the figure shows,
little or no current flows in the neutral
conductor when the loads are nonlinear and balanced.
Power disturbances such as lightning

can elevate the ground potential
between two communicating pieces
of electronic equipment with different
ground references. The result is current
flowing through the data cable, causing
component failure, terminal lock-up,
data corruption and interference.
With the arrival of nonlinear electronic

loads, where the AC voltage is converted to a DC voltage, harmonics are
created because of the use of only part
of the AC sine wave. In this conversion
from AC to DC, the electronics are turned
on in the 60 cycle wave at a given point
in time to obtain the required DC level.
The use of only part of the sign wave
causes harmonics.
NFPA 780 D4.8 warns that surge

suppression devices should be installed
on all wiring entering or leaving electronic equipment, usually power, data
or communication wiring.
Surge suppressers should be installed
at both ends of a data or communication cable. In those situations where
one end of the cable is not connected
into an electronic circuit (e.g., contactor
coil), protection on the electronic end
only is required.
To prevent the coupling or inducing of
power disturbances into communication
lines, the following should be avoided:
Data cables should not be run over

fluorescent lighting fixtures
Data cables should not be in the
vicinity of electric motors
The right category cable should
be used to ensure transmission
performance
Data cables must be grounded at
both ends when communicating
between buildings
It is important to note that the current

distortion caused by loads such as
rectifiers or switch mode power
supplies causes the voltage distortion.
That voltage distortion is caused by
distorted currents flowing through an
impedance. The amount of voltage
distortion depends on:
System impedance
Amount of distorted current
Devices that can cause harmonic

disturbances include rectifiers,
thrusters and switching power supplies, all of which are nonlinear.
Further, the proliferation of electronic
equipment such as computers, UPS
systems, variable speed drives,
programmable logic controllers, and
the like: non-linear loads have become
a significant part of many installations.
Other types of harmonic-producing
loads include arcing devices (arc
furnaces, fluorescent lights) and iron
core storable devices (transformers,
especially during energization).
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21

April 2016
Sheet 01 078
Power Quality
i
ii
1
2
Nonlinear load currents vary widely

from a sinusoidal wave shape; often
they are discontinuous pulses. This
means that nonlinear loads are
extremely high in harmonic content.
Triplen harmonics are the 3rd, 9th,
15th,...harmonics. Further, triplen
harmonics are the most damaging
to an electrical system because these
harmonics on the A-phase, B-phase
and C-phase are in sequence with each
other. Meaning, the triplen harmonics
present on the three phases add

together in the neutral, as shown in
Figure 1.4-17, rather than cancel each
other out, as shown in Figure 1.4-16.
Odd non-triplen harmonics are
classified as positive sequence
or negative sequence and are the
1st, 5th, 7th, 11th, 13th, etc.
Harmonic Issues
In general, as the order of a harmonic

gets higher, its amplitude becomes
smaller as a percentage of the fundamental frequency.
In general, harmonics present on

a distribution system can have the
following detrimental effects:
1. Overheating of transformers and

rotating equipment.
60 Hz Fundamental
2. Increased hysteresis losses.
3. Decreased kVA capacity.
A Phase
4. Overloading of neutral.
5
6
Harmonic currents perform no work

and result in wasted electrical energy
that may over burden the distribution
system. This electrical overloading
may contribute to preventing an
existing electrical distribution system
from serving additional future loads.
5. Unacceptable neutral-to-ground
voltages.
120
Lagging
6. Distorted voltage and current

waveforms.
B Phase
7. Failed capacitor banks.

8. Breakers and fuses tripping.
8
120
Lagging
C Phase
9
10
Balance
Neutral
Current
11
12
Figure 1.4-16. Balanced Neutral Current Equals Zero
60 Hz Fundamental
13
3rd Harmonic
A Phase
14
15
120
Lagging
B Phase
16
17
120
Lagging
C Phase
18
19
21
20
Neutral
Triplen
Current
Phase Triplen Harmonics
Added in the Neutral
Figure 1.4-17. Unbalanced Single-Phase Loads with Triplen Harmonics

9. Double or ever triple sized neutrals

to defy the negative effects of
triplen harmonics.
In transformers, generators and
uninterruptible power supplies (UPS)
systems, harmonics cause overheating
and failure at loads below their ratings
because the harmonic currents cause
greater heating than standard 60 Hz
current. This results from increased
eddy current losses, hysteresis losses
in the iron cores, and conductor skin
effects of the windings. In addition,
the harmonic currents acting on the
impedance of the source cause
harmonics in the source voltage, which
is then applied to other loads such as
motors, causing them to overheat.
The harmonics also complicate the
application of capacitors for power
factor correction. If, at a given harmonic
frequency, the capacitive impedance
equals the system reactive impedance,
the harmonic voltage and current can
reach dangerous magnitudes. At the
same time, the harmonics create
problems in the application of power
factor correction capacitors, they
lower the actual power factor. The
rotating meters used by the utilities for
watthour and various measurements
do not detect the distortion component
caused by the harmonics. Rectifiers
with diode front ends and large DC side
capacitor banks have displacement
power factor of 90% to 95%. More
recent electronic meters are capable
of metering the true kVA hours taken
by the circuit.
CA08104001E

April 2016
1.4-23
Sheet 01 079
Power Quality
Single-phase power supplies for
computer and fixture ballasts are
rich in third harmonics and their
odd multiples.
Even with the phase currents perfectly
balanced, the harmonic currents in
the neutral can total 173% of the
phase current. This has resulted in
overheated neutrals. The Information
Technology Industry Council (ITIC)
formerly known as CBEMA, recommends that neutrals in the supply to
electronic equipment be oversized
to at least 173% of the ampacity of
the phase conductors to prevent
problems. ITIC also recommends
derating transformers, loading them
to no more than 50% to 70% of their
nameplate kVA, based on a rule-ofthumb calculation, to compensate
for harmonic heating effects.
In spite of all the concerns they
cause, nonlinear loads will continue
to increase. Therefore, the design of
nonlinear loads and the systems that
supply them will have to be designed
so that their adverse effects are greatly
reduced. Table 1.4-4 shows the typical
harmonic orders from a variety of
harmonic generating sources.
Total Harmonic Distortion

Revised standard IEEE 519-1992
indicates the limits of current distortion allowed at the PCC (Point of
Common Coupling) point on the
system where the current distortion
is calculated, usually the point of
connection to the utility or the main
supply bus of the system.
The standard also covers the harmonic
limits of the supply voltage from the
utility or cogenerators.
Class
AN
DF
Special application 2
General system
Dedicated system
10
5
2
16,400
22,800
36,500
3%
5%
10%
Special systems are those where the rate

of change of voltage of the notch might
mistrigger an event. AN is a measurement
of notch characteristics measured in
volt-microseconds, C is the impedance
ratio of total impedance to impedance
at common point in system. DF is
distortion factor.
Table 1.4-6. Utility or Cogenerator Supply

Voltage Harmonic Limits
2.369 kV 69138 kV >138 kV
Typical
Harmonics 1
Maximum
individual
harmonic
3.0%
6-pulse rectifier
12-pulse rectifier
18-pulse rectifier
5, 7, 11, 13, 17, 19

11, 13, 23, 25
17, 19, 35, 37
Total
harmonic
distortion
5.0%
Switch-mode power
supply
Fluorescent lights
Arcing devices
Transformer energization
3, 5, 7, 9, 11, 13
3, 5, 7, 9, 11, 13
2, 3, 4, 5, 7
2, 3, 4
Source
Generally, magnitude decreases as harmonic

order increases.
Maximum Harmonic Current Distortion in

Percent of IL
Individual Harmonic Order (Odd Harmonics)
ISC /IL
<20 3
20<50
50<100
100<1000
>1000
3
Table 1.4-5. Low Voltage System Classification

and Distortion Limits for 480 V Systems
Voltage
Range
Table 1.4-4. Source and Typical Harmonics
Table 1.4-7. Current Distortion Limits for

General Distribution Systems (120 69,000 V)
1.5%
2.5%
1.0%
1.5%
Vh
Percentages are x 100 for each
V1
harmonic
and
h = hmax
Vthd =
1/2
<11
4.0
7.0
10.0
12.0
15.0
11 17
23
35 TDD
<h <h <h <h
<17 <23 <35
2.0
3.5
4.5
5.5
7.0
1.5
2.5
4.0
5.0
6.0
0.6
1.0
1.5
2.0
2.5
0.3
0.5
0.7
1.0
1.4
5.0
8.0
12.0
15.0
20.0
All power generation equipment is limited

to these values of current distortion,
regardless of actual ISC/IL where:
ISC = Maximum short-circuit current at PCC.
IL = Maximum demand load current
(fundamental frequency component) at PCC.
TDD = Total Demand Distortion. Even

harmonics are limited to 25% of the odd
harmonic limits above. Current distortions
that result in a DC offset, e.g., half-wave
converters, are not allowed.
i
ii
1
2
3
4
5
6
Harmonic Solutions
In spite of all the concerns nonlinear
loads cause, these loads will continue
to increase. Therefore, the design
of nonlinear loads and the systems
that supply them will need design so
adverse harmonic effects are greatly
reduced. Table 1.4-8 and depicts many
harmonic solutions along with their
advantages and disadvantages.
Eatons Engineering Services &
Systems Group (EESS) can perform
harmonic studies and recommend
solutions for harmonic problems.
7
8
9
10
11
12
13
14
2
Vh
h=2
It is important for the system designer
to know the harmonic content of the
utilitys supply voltage because it will
affect the harmonic distortion of
the system.
15
16
17
18
19
20
21
CA08104001E

April 2016
Sheet 01 080
Power Quality
i
ii
Table 1.4-8. Harmonic Solutions for Given Loads

Load
Type
Solutions
Advantages
Disadvantages
Drives and rectifiers

includes three-phase
UPS loads
Line reactors
Inexpensive
For 6-pulse standard drive/rectifier, can
May require additional compensation
1
2
reduce harmonic current distortion from

80% down to about 3540%
K-rated/drive isolation
transformer
Offers series reactance (similar to line
DC choke
Slightly better than AC line reactors
reactors) and provides isolation for

some transients
for 5th and 7th harmonics
85% reduction versus standard
12-pulse convertor
Harmonic mitigating
transformers/phase shifting
6-pulse drives
Substantial (5080%) reduction in harmonics
when used in tandem
No advantage over reactors for
reducing harmonics unless in pairs

for shifting phases
Not always an option for drives
Less protection for input semiconductors
Cost difference approaches 18-pulse drive
and blocking filters, which guarantee

IEEE 519 compliance
Harmonic cancellation highly dependent
on load balance
Must have even multiples of matched loads
Bus connectedaccommodates
Tuned filters
Broadband filters
Makes 6-pulse into the equivalent
18-pulse converter
Excellent harmonic control for drives
load diversity
Provides PF correction
of 18-pulse
High cost
Computers/
switch-mode
power supplies
Active filters
Handles load/harmonic diversity

Complete solution up to 50th harmonic
High cost
Neutral blocking filter
Eliminates the 3rd harmonic from load

Relieves system capacity
Possible energy savings
High cost
May increase voltage distortion
Harmonic mitigating
transformers
3rd harmonic recalculated back to the load

When used as phase-shifted transformers,
Requires fully rated circuits and
oversized neutrals to the loads
reduces other harmonics

Reduces voltage flat-topping
10
11
12
must be resized if system changes

Higher cost
Requires one filter per drive
above 100 hp
IEEE 519 compliant
7
8
Requires allocation analysis

Sized only to the requirements of that system;
Fluorescent
lighting
Oversized neutral/derated
transformer
Tolerate harmonics rather than correct

Typically least expensive
Upstream and downstream equipment
K-rated transformer
Tolerate harmonics rather than correct
Does not reduce system harmonics
Harmonic mitigating
transformers
3rd harmonic recalculated back to the load

When used as phase-shifted transformers,
Requires fully rated circuits and
fully rated for harmonics
oversized neutrals to the loads
reduces other harmonics

Reduces voltage flat-topping
13
K-rated transformer
Tolerate harmonics rather than correct them
Does not reduce system harmonics
Low distortion ballasts
Reduce harmonics at the source
Additional cost and typically more
Active filters
Fast response and broadband
High cost
expensive than system solutions
14
Welding/arcing
loads
harmonic correction
Reduces voltage flicker
15
Tuned filters
SCR controlled tuned filters simulates
an active filter response
16
17
System
solutions
SCR controlled units are high cost
but fixed filters are reasonable
Tuned filters
Provides PF correction
Lower cost compared to other systems
System analysis required to verify application.
Harmonic mitigating
transformers
Excellent choice for new design or upgrade
No PF correction benefit
Active filters
Ideal solution and handles system diversity
Highest cost
Must be resized if system changes
18
19
20
21
CA08104001E
April 2016

Uninterruptible Power Systems (UPS)
1.4-25
Sheet 01 081
5. Uninterruptible Power
Systems (UPS)
The advent of solid-state semiconductors over 40 years ago, and their
subsequent evolution to transistors,
and the miniaturization of electronics
into microprocessor over 25 years ago,
has created numerous computation
machines that assist us in every
conceivable manner. These machines,
and their clever configurations,
whether they take the form of
computers, appliance controls, fax
machines, phone systems, computers
of all sizes, server systems and server
farms, emergency call centers, data
processing at banks, credit companies,
private company communication
networks, government institutions and
defense agencies, all rely on a narrow
range of nominal AC power in order
for these devices to work properly.
Indeed, many other types of equipment also require that the AC electrical
power source be at or close to nominal
voltage and frequency. Disturbances of
the power translate into failed
processes, lost data, decreased
efficiency and lost revenue.
The normal power source supplied by

the local utility or provider is not stable
enough over time to continuously
serve these loads without interruption.
It is possible that a facility outside a
major metropolitan area served by the
utility grid will experience outages of
some nature 1520 times in one year.
Certain outages are caused by the
weather, and others by the failure
of the utility supply system due to
equipment failures or construction
interruptions. Some outages are
only several cycles in duration, while
others may be for hours at a time.
In a broader sense, other problems
exist in the area of power quality, and
many of those issues also contribute
to the failure of the supply to provide
that narrow range of power to the
sensitive loads mentioned above.
Power quality problems take the
form of any of the following: power
failure, power sag, power surge,
undervoltage, overvoltage, line noise,
frequency variations, switching
transients and harmonic distortion.
Regardless of the reason for outages
and power quality problems, the
sensitive loads can not function
normally without a backup power
source, and in many cases, the loads
must be isolated from the instabilities of
the utility supply and power quality
problems and given clean reliable
power on a continuous basis, or be
able to switch over to reliable clean
electrical power quickly.
Uninterruptible power supply (UPS)

systems have evolved to serve the
needs of sensitive equipment and
can supply a stable source of electrical
power, or switch to backup to allow
for an orderly shutdown of the loads
without appreciable loss of data or
process. In the early days of mainframe computers, motor-generator
sets provide isolation and clean power
to the computers. They did not have
deep reserves, but provided extensive
ride-through capability while other
sources of power (usually standby
emergency engine generator sets) were
brought to serve the motor-generator
sets while the normal source of power
was unstable or unavailable.
UPS systems have evolved along the
lines of rotary types and static types
of systems, and they come in many
configurations, and even hybrid
designs having characteristics of
both types. The discussion that
follows attempts to compare and
contrast the two types of UPS
systems, and give basic guidance
on selection criteria. This discussion
will focus on the medium, large and
very large UPS systems required by
users who need more than 10 kVA of
clean reliable power.
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

April 2016
Sheet 01 082
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
Power Ratings of UPS Systems
types of hybrid UPS systems are not

the focus of this discussion, because
only one or two vendors offer these
hybrid types of rotary UPS systems,
although admittedly they continue to
be used in very large-scale data center
applications. See Figure 1.4-18 for the
modern high speed Rotary UPS
systems discussed in this section
of the guide. These types of modern
rotary UPS systems are advanced,
integrated designs using scalable
configurations of high-speed flywheel,
motor and generator in one compact
UPS package. The new rotary
technologies have the potential to
replace battery backup systems, or
at least reduce the battery content
for certain applications. The appeal
of rotary systems is the avoidance of
the purchase, maintenance and facility
space required by DC battery based
backup systems.
Small UPS: Typically 300 VA to 10 kVA,

and sometimes as high as 18 kVA
Medium UPS: 1060 kVA
Large UPS: 100200 kVA units, and
higher when units are paralleled
Very Large UPS: 200750 kVA
units, and higher when units
are paralleled
Each of these categories is arbitrary
because manufacturers have many
different UPS offerings for the same
application. The choice of UPS type
and the configuration of UPS modules
for a given application depends upon
many factors, including how many
power quality problems the UPS is
expected to solve; how much future
capacity is to be purchased now for
future loads; the nature of the sensitive loads and load wiring; which
type of UPS system is favored, rotary
or static; choices of battery or DC
storage technology considered; and
a host of other application issues.
High-Speed Rotary
Concept of Operation
300900 kVA/720 kW maximum.
The modern rotary type of UPS

operation is understood by reviewing
the four topics below: startup mode,
normal operation mode, discharge
mode and recharge mode.
Typical Rotary Configurations
Startup Mode
Rotary UPS systems are among the

oldest working systems developed
to protect sensitive loads. Many of
these systems are complicated enginegenerator sets coupled with high
inertial flywheels operated at relatively
low rotational speeds. These legacy
The UPS output is energized on

bypass as soon as power is applied
from the source to the system input.
The UPS continues the startup
procedure automatically when the
front panel controls are placed into
the Online position. Internal UPS
Rotary UPS Systems

Typical Ratings
13
14
system checks are performed then

the input contactor is closed. The static
disconnect switch is turned on and the
conduction angle is rapidly increased
from zero to an angle that causes the
DC bus voltage between the utility
converter and the flywheel converter
to reach approximately 650 V through
the rectifying action of the freewheeling diodes in the utility converter.
As soon as this level of DC voltage is
reached, the static disconnect turns
on fully. The next steps involved the
utility converter IGBTs to start firing,
which allows the converter to act as
a rectifier, a regulating voltage source
and an active harmonic filter. As the
IGBTs begin to operate, the DC bus
is increased to a normal operating
voltage of approximately 800 V, and
the output bus is transferred from
bypass to the output of the power
electronics module. The transfer from
bypass is completed when the output
contactor is closed and the bypass
contactor opened in a make-beforebreak manner.
The firing of the SCRs in the static
disconnect switch is now changed so
that each SCR in each phase is only
turned on during the half-cycle, which
permits real power to flow from the
utility supply to the UPS. This firing
pattern at the static disconnect switch
prevents power from the flywheel
from feeding backward into the
utility supply and ensures that all of
the flywheel energy is available to
support the load.
Static Bypass Option

It = Input Current
Ir = Real Load Current
Ic = Charging Current
Ig = Voltage Regulation Current
Bypass Contactor
15
It = Ir + Ic + Ig
16
Input
Contactor
Id = Ih + Ix + Ir
Static Disconnect
Switch
Line Inductor
Output
Contactor
Source
Load
17
18
Flywheel Converter
Ix
Field Coil
Driver
dc
Ic
Filter Inductor
dc
ac
19
20
Utility Converter
Inverter
Fuse
Ig
ac
Output Transformer
Id = Output Current
Ih = Harmonic Current
Ix = Reactive Load Current
Ir = Real Load Current
Ih
Integrated Motor/Flywheel/
and Generator
Figure 1.4-18. Typical-High Speed Modern Rotary UPS
21
CA08104001E
April 2016

1.4-27
Sheet 01 083
Immediately after the output is transferred from bypass to the power electronic module, the flywheel field is
excited, which also provides magnetic
lift to unload the flywheel bearings.
The flywheel inverter is turned on
and gradually increases frequency
at a constant rate to accelerate the
flywheel to approximately 60 rpm.
Once the flywheel reaches 60 rpm,
the flywheel inverter controls the
acceleration to keep currents below the
maximum charging and the maximum
input settings. Once the flywheel
reaches 4000 rpm, the UPS is fully
functional and capable of supporting
the load during a power quality event.
flywheel acceleration continues until
the Flywheel reaches full charge at
7700 rpm. The total time to complete
startup is less than 5 minutes.
Normal Operation Mode

Once the UPS is started and the
flywheel is operating at greater than
4000 rpm, the UPS is in the normal
operating mode where it is regulating
output voltage and supplying reactive
and harmonic currents required by the
load. At the same time it cancels the
effect of load current harmonics on the
UPS output voltage.
Input current consists of three components: real load current, charging
current, and voltage regulation current.
Real current is current that is in phase
with the supply voltage and supplies
real power to the load. Real current
flowing through the line inductor causes
a slight phase shift of the current
lagging the voltage by 10 degrees
and ensures that the UPS can quickly
transfer to bypass without causing
unacceptable switching transients. The
second component is charging current
required by the flywheel to keep the
rotating mass fully charged at rated
rpm, or to recharge the rotating mass
after a discharge. The power to maintain full charge is low at 2 kW and
is accomplished by the IGBTs of the
flywheel converter gating to provide
small pulses of motoring current to the
flywheel. This current can be much
higher if fast recharge times are
selected. The final component of input
current is the voltage regulation current,
which is usually a reactive current that
circulates between the input and the
utility converter to regulate the output
voltage. Leading reactive current
causes a voltage boost across the line

inductor, and a lagging current causes
a bucking voltage. By controlling the
utility converter to maintain nominal
output voltage, just enough reactive
current flows through the line inductor
to make up the difference between the
input voltage and the output voltage.
The load current consists of three
components: the harmonic current
required by the load, the reactive load
current, and the real current, which
does the work. The utility converter
supplies both the harmonic and
reactive currents. Because these
currents supply no net power to the
load, the flywheel supplies no energy
for these currents. They circulate
between the utility converter and the
load. The power stage controls analyze
the harmonic current requirements of
the load and set the firing angle of
the inverter IGBTs to make the utility
converter a very low impedance source
to any harmonic currents. Thus,
nonlinear load currents are supplied
almost entirely from the utility
converter with little effect on the
quality of the UPS output voltage
waveform and with almost no
transmission of load harmonics
currents to the input of the UPS.
Discharge Mode
The UPS senses the deviation of
the voltage or frequency beyond
programmed tolerances and quickly
disconnects the supply source by
turning off the static disconnect switch
and opening the input contactor. The
disconnect occurs in less than one-half
cycle. Then the utility converter starts
delivering power from the DC bus to
the load, and the flywheel converter
changes the firing point of its IGBTs
to deliver power to the DC bus. The
UPS maintains a clean output voltage
within 3% or nominal voltage to the
load when input power is lost.
as the load power is completely

transferred to the input source, the utility converter and flywheel converter
start to recharge the flywheel and
return to normal operation mode. The
flywheel recharge power is programmable between a slow and fast rate,
and using the fast rate results in an
increase of UPS input current over
nominal levels. Recharging the flywheel
is accomplished by controlling the
utility and flywheel converter in a
similar manner as is used to maintain
full charge in the normal operation
mode, however the IGBT gating points
are changed to increase current into
the flywheel.
High-Speed Rotary Advantages
High-Speed Rotary Disadvantages
Recharge Mode
When input power is restored to
acceptable limits, the UPS synchronizes
the output and input voltages, closes
the input contactor and turns on the
static disconnect switch. The utility
converter then transfers power from
the flywheel to the input source by
linearly increasing the real input
current. The transfer time is programmable from 1 to 15 seconds. As soon
Addresses all power quality

problems
Battery systems are not required
or used
No battery maintenance required
Unlimited discharge cycles
150-second recharge time available
Wide range of operating temperatures can be accommodated
(20 to 40 C)
Small compact size and less floor
space required (500 kW systems
takes 20 sq ft)
N+1 reliability available up to
900 kVA maximum
No disposal issues
Flywheel does not have deep

reserve capacityrides through
for up to 13 seconds at 100% load
Some enhanced flywheel systems
may extend the ride through to
30 seconds at 100% load
Mechanical flywheel maintenance
required every 23 years, and oil
changes required every year
Recharge fast rates require the
input to be sized for 125% of
nominal current
Flywheels failures in field not
understood
Requires vacuum pumps for
high-speed flywheels
Limited number of vendors and
experience
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

April 2016
Sheet 01 084
Static UPS Systems

Typical Ratings
ii
1
2
3
4
5
6
7
8
9
10
11
40750 kVA/600 kW, and higher when

multiple units are paralleled.
Typical Static UPS Configurations

Static UPS systems modules are
available in three basic types of
configurations known as standby, line
interactive and double conversion.
See Tab 33 in this guide for details on
all the UPS configurations available
from Eaton. The lighter power ratings
are likely to be one of the first two
types of configurations, e.g., standby
or line interactive. Most medium or
large static UPS installations use the
double conversion technology in one
or multiple module configurations,
i.e., or multiple UPS units in parallel.
Figure 1.4-19 illustrates the one-line
diagram of a simple single Double
Conversion UPS module. Brief
explanations appear for the standby
and line interactive UPS systems
after the text explaining the Double
Conversion static UPS type of system.
A. Double conversion concept of
operationthe basic operation of
the Double Conversion UPS is:
1. Normal power is connected to
the UPS input through the facility
This usually involves two input
circuits that must come from the
same source.
mode in 150120 milliseconds.

When the UPS recognizes a
requirement to transfer to the
bypass mode, it simultaneously
turns the static switch ON, the
output breaker to OPEN, and the
bypass breaker to CLOSE. The
output breaker opens and the
bypass breaker closes in about
50 milliseconds. The restoration
of normal conditions at the UPS
results in the automatic restoration
of the UPS module powering the
load through the rectifier/charger
and inverter with load isolation
from power quality problems, and
the opening of the bypass circuit.
2. The Rectifier/Charger function

converts the normal AC power to
DC power to charge the battery
and power the inverter. The load
is isolated from the normal
input source.
3. The battery stores DC energy
for use when input power to the
UPS fails. The amount of power
available from the DC battery
system and time to discharge
voltage is a function of the type of
battery selected and the amperehour sized used. Battery systems
should be sized for no less than
5 minutes of clean power usage
from a fully charged state, and, in
many cases, are sized to provide
more time on battery power.
4. The DC link connects the output
of the rectifier/charger to the input
of the inverter and to the battery.
Typically the rectifier/charger is
sized slightly higher than 100% of
UPS output because it must power
the inverter and supply charger
power to the battery.
5. The bypass circuit provides a
path for unregulated normal
power to be routed around the
major electronic sub-assemblies
of the UPS to the load so that the
load can continue to operate during
maintenance, or when the UPS
electronics fails. The bypass static
switch can switch to conducting
Static Double Conversion Advantages
Addresses all power quality

problems
Suitable for applications from
5 kVA to over 2500 kVA
Simple battery systems are
sized for application
Long battery backup times and
long life batteries are available
Higher reliability is available
using redundant UPS modules
12
UPS Module
Bypass Breaker (Optional)
13
Bypass Static Switch
14
15
Source
Load
Normal Rectifier/Charger
Breaker
AC
Inverter
DC
DC
16
17
18
Output
Breaker
AC
Battery Breaker
Battery
Figure 1.4-19. Typical Static UPS, Double Conversion Type with Battery Backup
19
20
21
CA08104001E

April 2016
1.4-29
Sheet 01 085
Static Double Conversion Disadvantages
Battery systems, battery maintenance

and battery replacement are required
Large space requirement for
battery systems (higher life takes
more space, e.g., 500 kW takes
80200 sq ft depending upon the
type of battery used, VRLA 10 year,
VRLA 20 year or flooded)
Limited discharge cycles of
battery system
Narrow temperature range
for application
Efficiencies are in the 9094%
range, which is lower than some line
interactive configurations
Bypass mode places load at risk
unless bypass has UPS backup
Redundancy of UPS modules
results in higher costs
Output faults are cleared by the
bypass circuit
Output rating of the UPS is 150%
for 30 seconds
Battery disposal and safety
issues exist
B. Standby UPS concept of

operationThe basic operation of
the Standby UPS is:
1. The Standby UPS topology is
similar to the double conversion
type, but the operation of the UPS
is different in significant ways.
Normal power is connected to
the UPS input through the facility
This usually involves two input
circuits that must come from the
same source. See Figure 1.4-20
for details.
2. The rectifier/charger function
converts the normal AC power to
DC power to charge the battery
only, and does not simultaneously
power the inverter. The load is
connected to the input source
through the bypass static switch.
The inverter is in the standby
mode ready to serve the load
from battery power if the input
power source fails.
3. The battery stores DC energy for

use by the inverter when input
power to the UPS fails. The
amount of power available from
the DC battery system and time to
discharge voltage is a function of
the type of battery selected and
the ampere-hour sized used.
Battery systems should be sized
for the anticipated outage.
4. The DC link connects the output of
the rectifier/charger to the input of
the inverter and to the battery.
Typically the rectifier/charger
is sized only to supply charger
power to the battery, and is
rated far lower than in the
double conversion UPS.
5. The bypass circuit provides a
direct connection of input source
to the load. The load operates
from unregulated power. The
bypass static switch can switch
to non-conducting mode in 150
120 milliseconds. When the UPS
recognizes the loss of normal
input power, it transfers to battery/
inverter mode by simultaneously
turning the Inverter ON and the
static switch OFF.
Static Standby UPS Advantages
Lower costs than double conversion

Rectifier and charger are
economically sized
Efficient design
Batteries are sized for the
application
C. Static line interactive UPS

concept of operationthe basic
operation of the Line Interactive
UPS is:
1. The Line Interactive type of UPS
has a different topology than the
static double conversion and
standby systems. The normal
input power is connected to the
load in parallel with a battery
and bi-directional inverter/charger
assembly. The input source usually terminates at a line inductor
and the output of the inductor is
connected to the load in parallel
with the battery and inverter/
charger circuit. See Figure 1.4-21
for more details.
2. The traditional rectifier circuit
is eliminated and this results
in a smaller footprint and
weight reduction. However, line
conditioning is compromised.
3. When the input power fails, the
battery/inverter charger circuit
reverses power and supplies the
load with regulated power.
Static Line Interactive UPS Advantages
Slight improvement of power

conditioning over standby
UPS systems
Small footprints and weights
Efficient design
Batteries are sized for the
application
Static Line Interactive UPS Disadvantages
Static Standby UPS Disadvantages
Impractical over 2 kVA

Little to no isolation of load from
power quality disturbances
Standby power is from battery alone
Battery systems, battery maintenance and battery replacement
are required
Limited discharge cycles of
battery system
Narrow temperature range for
application
Output faults are cleared by the
bypass circuit
issues exist
Impractical over 5 kVA

Not as good conditioning as
double conversion
Standby power is from battery alone
Battery systems, battery maintenance and battery replacement
are required
Limited discharge cycles for the
battery system
Narrow temperature range for
application
issues exist
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

April 2016
Sheet 01 086
UPS Module
ii
Bypass Static Switch
1
2
Load
Source
Normal
Breaker
3
4
Rectifier/
Charger
Inverter
AC
DC
DC
AC
Battery
Breaker
5
Battery
6
7
Output
Breaker
Figure 1.4-20. Typical Static UPS, Standby Type with Battery Backup
UPS Module
9
10
Load
Source
Inductor
11
Bidirectional
Inverter/Charger
12
DC
13
AC
14
15
16
Battery
Figure 1.4-21. Typical Static UPS, Line Interactive Type with Battery Backup
17
18
19
20
21
CA08104001E

April 2016
1.4-31
Sheet 01 087
Secondary Voltage Selection
Technical Factors
The choice between 208Y/120 V and

480Y/277 V secondary distribution for
commercial and institutional buildings
depends on several factors. The most
important of these are size and types
of loads (motors, fluorescent lighting,
incandescent lighting, receptacles)
and length of feeders. In general, large
motor and fluorescent lighting loads,
and long feeders, will tend to make the
higher voltages, such as 480Y/277 V,
more economical. Very large loads
and long runs would indicate the use
of medium voltage distribution and
loadcenter unit substations close to
the loads. Conversely, small loads,
short runs and a high percentage of
incandescent lighting would favor
lower utilization voltages such as
208Y/120 V.
The principal advantage of the use of

higher secondary voltages in buildings
is that for a given load, less current
means smaller conductors and lower
voltage drop. Also, a given conductor
size can supply a large load at the
same voltage drop in volts, but a lower
percentage voltage drop because of
the higher supply voltage. Fewer or
smaller circuits can be used to transmit
the power from the service entrance
point to the final distribution points.
Smaller conductors can be used in many
branch circuits supplying power loads,
and a reduction in the number of lighting branch circuits is usually possible.
It is easier to keep voltage drops within
acceptable limits on 480 V circuits than
on 208 V circuits. When 120 V loads are
supplied from a 480 V system through

step-down transformers, voltage drop
in the 480 V supply conductors can be
compensated for by the tap adjustments on the transformer, resulting
in full 120 V output. Because these
transformers are usually located close
to the 120 V loads, secondary voltage
drop should not be a problem. If it is,
taps may be used to compensate by
raising the voltage at the transformer.
The interrupting ratings of circuit
breakers and fuses at 480 V have
increased considerably in recent years,
and protective devices are now available
for any required fault duty at 480 V.
In addition, many of these protective
devices are current limiting, and can
be used to protect downstream equipment against these high fault currents.
ii
1
2
3
4
5
6
Industrial installations, with large

motor loads, are almost always 480 V,
often ungrounded delta or resistance
grounded delta or wye systems (see
section on ground fault protection).
Elevator
Panel
Typical
Practical Factors
Because most low voltage distribution
equipment available is rated for up to
600 V, and conductors are insulated for
600 V, the installation of 480 V systems
uses the same techniques and is
essentially no more difficult, costly, or
hazardous than for 208 V systems. The
major difference is that an arc of 120 V
to ground tends to be se lf-extinguishing, while an arc of 277 V to ground
tends to be self-sustaining and likely to
cause severe damage. For this reason,
the National Electrical Code requires
ground fault protection of equipment
on grounded wye services of more
than 150 V to ground, but not exceeding
600 V phase-to-phase (for practical
purpose, 480Y/277 V services), for any
service disconnecting means rated
1000 A or more. The National Electrical
Code permits voltage up to 300 V
to ground on circuits supplying
permanently installed electric discharge
lamp fixtures, provided the luminaires
do not have an integral manual switch
and are mounted at least 8 ft (2.4 m)
above the floor. This permits a threephase, four-wire, solidly grounded
480Y/277 V system to supply directly all
of the fluorescent and high-intensity
discharge (HID) lighting in a building at
277 V, as well as motors at 480 V.
Emergency
Lighting Panel
Typical
HVAC
Panel
(Typical Every
Third Floor)
HVAC
Feeder
Busway
Riser
11
Emergency
Lighting
Riser
Typical
Building and
Miscellaneous
Loads
10
Typical
480Y/277 V
208Y/120 V
Panel
Panel
Dry Type Transformer
480-208Y/120 V
(Typical Every Floor)
Elevator
Riser
Typical
12
13
Typical
14
Typical
Typical
Spare
1
15
Automatic
Transfer Switch
1 4000 A
Main CB
Gen. CB
CTs
PTs
Utility
Service
Utility
Metering
Emergency
or Standby
Generator
4000A at 480Y/277V
100,000A Available Fault Current
16
17
18
Figure 1.4-22. Typical Power Distribution and Riser Diagram for a Commercial Office Building
1
Include ground fault trip.
19
20
21
CA08104001E

April 2016
Sheet 01 088
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Economic Factors
Utilization equipment suitable for
principal loads in most buildings
is available for either 480 V or 208 V
systems. Three-phase motors and
their controls can be obtained for either
voltage, and for a given horsepower
are less costly at 480 V. Fluorescent and
HID lamps can be used with either 277 V
or 120 V ballasts. However, in almost all
cases, the installed equipment will have
a lower total cost at the higher voltage.
Energy Conservation
Because of the greatly increased cost
of electrical power, designers must
consider the efficiency of electrical
distribution systems, and design for
energy conservation. In the past,
especially in commercial buildings,
design was for lowest first cost,
because energy was inexpensive.
Today, even in the speculative office
building, operating costs are so high
that energy-conserving designs can
justify their higher initial cost with a
rapid payback and continuing savings.
Buildings that must meet LEED certifications may require energy-saving
designs. There are four major sources
of energy conservation in a commercial
buildingthe lighting system, the
motors and controls, the transformers
and the HVAC system.
The lighting system must take
advantage of the newest equipment
and techniques. New light sources,
familiar light sources with higher
efficiencies, solid-state ballasts with
dimming controls, use of daylight,
environmental design, efficient
luminaires, computerized or
programmed control, and the like,
are some of the methods that can
increase the efficiency of lighting
systems. They add up to providing
the necessary amount of light, with the
desired color rendition, from the most
efficient sources, where and when it is
needed, and not providing light where
or when it is not necessary. Using the
best of techniques, office spaces that
originally required as much as 3.5W
per square foot have been given
improved lighting, with less glare
and higher visual comfort, using as
little as 1.0 to 2.0W per square foot.
In an office building of 200,000 square
feet (60,960 m), this could mean a
saving of 400 kW, which, at $0.05 per
kWh, 250 days per year, 10 hours per
day, could save $50,000 per year in
energy costs. Obviously, efficient
lighting is a necessity.
Motors and controls are another cause

of wasted energy that can be reduced.
New, energy-efficient motor designs
are available using more and better
core steel, and larger windings.
For any motor operating 10 or more
hours per day, it is recommended to
use the energy-efficient types. These
motors have a premium cost of about
20% more than standard motors.
Depending on loading, hours of use
and the cost of energy, the additional
initial cost could be repaid in energy
saved within a few months, and it
rarely takes more than two years.
Because, over the life of a motor, the
cost of energy to operate it is many
times the cost of the motor itself, any
motor with many hours of use should
be of the energy-efficient type.
Where a motor drives a load with
variable output requirements such
as a centrifugal pump or a large fan,
customary practice has been to run the
motor at constant speed, and to throttle
the pump output or use inlet vanes or
outlet dampers on the fan. This is highly
inefficient and wasteful of energy. In
recent years, solid-state variablefrequency, variable-speed drives for
ordinary induction motors have been
available, reliable and relatively
inexpensive. Using a variable-speed
drive, the throttling valves, inlet vanes
or output dampers can be eliminated,
saving their initial cost and energy
over the life of the system. An
additional benefit of both energyefficient motors and variable-speed
drives (when operated at less than
full speed) is that the motors operate
at reduced temperatures, resulting in
increased motor life.
Transformers have inherent losses.
Transformers, like motors, are designed
for lower losses by using more and
better core materials, larger conductors,
etc., and this results in increased initial
cost. Because the 480 V to 208Y/120 V
stepdown transformers in an office
building are usually energized 24 hours
a day, savings from lower losses can
be substantial, and should be considered in all transformer specifications.
One method of obtaining reduced
losses is to specify transformers with
220 C insulation systems designed for
150 C average winding temperature
rise, with no more than 80 C (or
sometimes 115 C) average winding
temperature rise at full load. A better
method would be to evaluate transformer
losses, based on actual loading cycles
throughout the day, and consider the
cost of losses as well as the initial cost
of the transformers in purchasing.
NEMA standard TP-1 is being adopted

by many states and is another method
of energy-efficient design. NEMA TP-1
establishes minimum operating
efficiencies for each distribution
transformer size at a loading equal to
35% of the transformer full load kVA.
The 35% loading value in the NEMA
standard reflects field studies conducted by the U.S. Department of
Energy, which showed that dry-type
transformers installed in commercial
facilities are typically loaded at an
average of 35% of their full load
capacity over a 24-hour time period.
Table 1.4-9 compares losses for
both low temperature rise and TP-1
transformers using a 75 kVA design.
Table 1.4-9. Load Losses
Temp.
Rise C
Load Losses in Watts
150
115
360
420
490
480
620
610
885
805
1535 2450
1170 1950
80
500
TP-1 150 230
535
310
615
480
730
745
945 1410
1235 2280
No
25% 35% 50% 75% Full
Loss Load Load Load Load Load
Efficiencies above TP-1. Candidates

Standard Level (CSL) is a DOE
efficiency evaluation for transformers.
CSL-1 is equivalent to TP-1. Levels
are from CSL-1 to CSL-5. CSL-3 is being
promoted for higher efficiency applications. A NEMA white paper Clarifications on the Use of DOE DesignLines
6, 7 and 8 is available from NEMA that
elaborates on
the matter.
HVAC systems have traditionally been
very wasteful of energy, often being
designed for lowest first cost. This,
too, is changing. For example, reheat
systems are being replaced by variable
air volume systems, resulting in equal
comfort with substantial increases in
efficiency. While the electrical engineer
has little influence on the design of the
HVAC system, he/she can specify that
all motors with continuous or long duty
cycles are specified as energy-efficient
types, and that the variable-air-volume
fans do not use inlet vanes or outlet
dampers, but are driven by variablespeed drives. Variable-speed drives
can often be desirable on centrifugal
compressor units as well. Since some
of these requirements will be in HVAC
specifications, it is important for the
energy-conscious electrical engineer
to work closely with the HVAC engineer
at the design stage.
CA08104001E

April 2016
1.4-33
Sheet 01 089
Building Control Systems

In order to obtain the maximum benefit
from these energy-saving lighting,
power and HVAC systems, they must
be controlled to perform their functions
most efficiently. Constant monitoring
would be required for manual operation,
so some form of automatic control
is required. The simplest of these
energy-saving controls, often very
effective, is a time clock to turn various
systems on and off. Where flexible
control is required, programmable
controllers may be used. These range
from simple devices, similar to multifunction time clocks, up to full microprocessor-based, fully programmable
devices, really small computers. For
complete control of all building systems,
computers with specialized software
can be used. Computers can not only
control lighting and HVAC systems,
and provide peak demand control, to
minimize the cost of energy, but they
can perform many other functions. Fire
detection and alarm systems can operate through the computer, which can
also perform auxiliary functions such
as elevator control and building communication in case of fire. Building
security systems, such as closed-circuit
television monitoring, door alarms and
intruder sensing, can be performed by
the same building computer system.
The time clocks, programmable
controllers and computers can
obtain data from external sensors
and control the lighting, motors and
other equipment by means of hard
wiring-separate wires to and from
each piece of equipment. In the more
complex systems, this would result in
a tremendous number of control
wires, so other methods are frequently
used. A single pair of wires, with electronic digital multiplexing, can control
or obtain data from many different
points. Sometimes, coaxial cable is
used with advanced signaling equipment. Some systems dispense with
control wiring completely, sending and
receiving digital signals over the
power wiring. The newest systems
may use fiber-optic cables to carry
tremendous quantities of data, free
from electromagnetic interference.
The method used will depend on
the type, number and complexity
of functions to be performed.
CA08104001E
Because building design and control

for maximum energy saving is important and complex, and frequently
involves many functions and several
systems, it is necessary for the design
engineer to make a thorough building
and environmental study, and to weigh
the costs and advantages of many
systems. The result of good design
can be economical, efficient operation.
Poor design can be wasteful and
extremely costly.
Distributed Energy Resources

Distributed energy resources (DER)
are increasingly becoming prominent
sources of electric power. Distributed
energy resources are usually small-tomedium sources of electric generation,
either from renewable or non-renewable sources. Sources include:
Photovoltaic (PV) systems

(solar systems)
Wind
Fossil-fueled (diesel, natural gas,
landfill gas, coal-bed methane)
generators (reciprocating engines)
Gas-fired turbines (natural gas, landfill gas, coal-bed methane)
Water-powered (hydro)
Fuel cells
Microturbines
Wave power
Coal-fired boilers
Distributed energy resources may also

be termed alternative energy resources.
Prime Power
DER can be used for generating prime
power or for cogeneration. Prime power
concerns a system that is electrically
separated from the electrical grid.
Prime power is generated at remote
sites where commercial electrical
power is not available.
Cogeneration
Cogeneration is another outgrowth of
the high cost of energy. Cogeneration
is the production of electric power concurrently with the production of steam,
hot water and similar energy uses. The
electric power can be the main product, and steam or hot water the
byproduct, as in most commercial
installations, or the steam or hot water
can be the most required product,
and electric power a byproduct, as
in many industrial installations. In
some industries, cogeneration has
been common practice for many
years, but until recently it has not
been economically feasible for most
commercial installations.
This has been changed by the high

cost of purchased energy, plus a
federal law (Public Utility Regulatory
Policies Act, known as PURPA) that
requires public utilities to purchase
any excess power generated by the
cogeneration plant. In many cases,
practical commercial cogeneration
systems have been built that provide
some or all of the electric power
required, plus hot water, steam, and
sometimes steam absorption-type
air conditioning. Such cogeneration
systems are now operating successfully in hospitals, shopping centers,
high-rise apartment buildings and
even commercial office buildings.
Where a cogeneration system is being
considered, the electrical distribution
system becomes more complex. The
interface with the utility company is
critical, requiring careful relaying
to protect both the utility and the
cogeneration system. Many utilities
have stringent requirements that
must be incorporated into the system.
Proper generator control and protection is necessary, as well. An on-site
electrical generating plant tied to an
electrical utility, is a sophisticated
engineering design.
Utilities require that when the
protective device at their substation
opens that the device connecting a
cogenerator to the utility open also.
One reason is that most cogenerators
are connected to feeders serving other
customers. Utilities desire to reclose
the feeder after a transient fault is
cleared. Reclosing in most cases will
damage the cogenerator if it had
remained connected to their system.
Islanding is another reason why the
utility insists on the disconnection of
the cogenerator. Islanding is the event
that after a fault in the utilitys system
is cleared by the operation of the
protective devices, a part of the
system may continue to be supplied
by cogeneration. Such a condition is
dangerous to the utilitys operation
during restoration work.
Major cogenerators are connected to
the subtransmission or the transmission
system of a utility. Major cogenerators
have buy-sell agreements. In such
cases, utilities use a trip transfer
scheme to trip the cogenerator breaker.
Guidelines that are given in ANSI
Guide Standard 1001 are a good
starting point, but the entire design
should be coordinated with the utility.
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21

April 2016
Sheet 01 090
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
PV System Design Considerations

Successful photovoltaic (PV) design
and construction is a complex multidiscipline endeavor. Proper planning
includes the site-layout study for
maximizing the suns energy harvesting for solar module selection, and
for updating the electrical/mechanical
design and construction to the latest
code and local constraints, including
fire marshal and seismic regulations.
Professionally prepared bid, permit,
construction and as-build drawings
shall be required and maintained.
For installation in/on/for existing
structures and sites, it is advised
that, at the minimum, pre-design
and construction tests be performed
for existing power-quality issues,
water drainage and the utility feeder/
transformer, and that electrical
distribution panel ratings are verified
sufficient for the planned solar system,
and the necessary arc flash studies be
performed. Connection to the utility
is always a utility interconnect agreement (application) process, and is
typically required for the available
solar incentives and programs offered
by the utility, municipality, state, and
various federal agencies and departments. State, and IRS tax incentives
require well-documented records.
Solar systems, while low maintenance,
do require periodic service. The solar
modules need to be washed-clean on
a regular basis and electrical terminations require initial and annual checks.
Cooling system filters are periodic
maintenance items, with the re-fresh
rate dependent upon typical and
unusual circumstances.
Solar systems installed near other new
construction where dust is generated
(e.g., grading, paving) or agricultural
environments may require additional
solar-system checks and services.
Planning for such contingencies is
the business of solar-system design,
construction and on-going operation.
Performance-based incentives
require verifiable metering, often
by registered/approved independent
third parties. Such monitoring periods
are typically for 60 or more months.
The S-Max inverter offers a wide range
of features and options to enable a
successful and long-lived solar-energy
harvesting solution. The isolation
step-up transformer, coupled to either
a negative or a positive grounded
solar array, ensures that the S-Max
can match to all (known) solar module
technologies.
The S-Max follows standard industry

and code practices in determining the
maximum number of solar modules
per string for the open-circuit photovoltaic (PV) voltage rise in cold
weather (Voc < 600 V as per NEC). Its
low 300 V MPPT lower-limit ensures
that multiple configurations are
possible for solar systems hot weather
voltage drop (i.e., Vmp as a function
of temperature, solar irradiance and
array-conductor voltage drop). The
following equations are the basis of
all solar system layout and design.
Consult professional engineering to
help when planning any solar system.
Engineering design firms offering
complete solar systems turn-key
calculations, drawings, construction
management and procurement are
a good place to start. Eaton offers
professional S-Max inverter application assistance, on-site commissioning
and maintenance services. Eaton
maintains a working relationship with
the best engineering services firms
across the country, and helps arrange
the successful implantation of your
solar system. The S-Max 250 kW
inverter and up-fit solutions easily
perform well in Mega-Watt and UtilityScale systems. Eaton also offers a
wide range of balance-of-system
(BOS) products, ranging from solar
module source and array combiners,
to DC and AC breakers, electrical and
distribution panels and switchgear.
Low Temperature Equation

Voc_max = Voc + (temp-differential x
temp-coefficient-of-Voc)
The temp-differential is the difference
between the standard module rating
at 25 C and the low temperature.
The voltage (Voc) will rise with
temperatures under 25 C.
Seek the solar module data sheet for
a list of standard test condition (STC)
data, temperature coefficients, and any
special module-related information to
determine the low-temperature open
circuit voltage. The NEC 2011, and
industry practice, requires the
use of the sites Extreme Annual
Mean Minimum Design Dry Bulb
Temperature data, available in the
ASHRAE Handbook. Code requires
that the resulting maximum voltage
(Voc) when added in the string of
modules be under 600 V. Record
low temperatures provide an
indication of system performance
when temperatures drop to these
levels. The S-Max inverter is designed
to standards higher than 600 Vdc.
High Temperature Equation

Once the maximum number of
modules per string is established,
the minimum number of modules per
string needs to be calculated. Here,
more site-related aspects come into
play, as the voltage of solar modules
decreases with increasing temperature. The modules (photovoltaic cell)
temperature is influenced by the
ambient temperature, reflected sunloads from nearby structures, parapet
walls, roof-coatings, etc. Air-flow
above and behind the solar modules
affect the cell temperature. The
accepted industry standards to add
to the module heating is listed below.
Unusual mounting systems may
adjust these figures, and it is best to
seek assistance in establishing and
planning such installations.
20 C for ground or pole mounted

solar systems
25 C for roof-top solar systems
mounted at inclined angles
(offers improved air-flow behind
the modules)
30 C for roof-top solar systems
mounted flat, yet at least 6.00 inches
(152.4 mm) above the roof surface
Vmp_min = Vmp + (temp-differential x
temp-coefficient-of-Vmp)
The temp-differential in this case
includes the above temperature
adders. The Vmp and related
temperature coefficients are listed
on the solar modules data sheets.
While the code doesnt indicate the
high temperature to use (i.e., because
it is an equipment application issue),
the industry standard is to evaluate the
ASHRAE 2% and 4% high temperature
figures, coupled to known location
differences. Record high temperatures
provide an indication of system
performance when climatic condition
reaches these levels.
Beyond the damaging temperature
affects on photovoltaic module Vmp
voltage levels, voltage drop in PV
conductors under such conditions also
need to be calculated and evaluated,
beyond normal temperatures. The
inverter only uses (knows) the Vmp
voltage at the inverter, not at the
PV modules.
Increasing grid voltages also puts a
constraint on the minimum Vmp
voltage at the DC input stage.
CA08104001E

April 2016
1.4-35
Sheet 01 091

To ensure the full MPPT range without
power-clipping (reduced power output),
prudent PV system designs shall consider the PV arrays Vmp voltage drop
to the point of the inverter connection,
ambient temperatures and the PV
system installation types effects on
Vmp, solar module miss-match and
tolerance variations, degradation of
solar modules over time (solar system
life), etc. Typical Vmp design values,
based upon known and expected
conditions are 510% over the
minimum MPPT tracking voltage.
Reference NEC 2011 Section 690,
Solar Photovoltaic Systems.
a charger to keep it at full capacity

when normal power is on, one or more
lamps, and a relay to connect the
battery to the lamps on loss of normal
power, is also permitted. Because
of the critical nature of emergency
power, ground fault protection is not
required. It is considered preferable
to risk arcing damage, rather than to
disconnect he emergency supply completely. For emergency power, ground
fault alarm is required by NEC 700.7(D)
to indicate a ground fault in solidly
grounded wye emergency systems
of more than 150 V to ground and
circuit-protective devices rated 1000 A
or more.
governmental agency having jurisdiction. Optional standby systems, not

legally required, are also covered in
the NEC (Article 702).
Emergency systems are intended to
supply power and illumination essential for safety to human life, when the
normal supply fails. NEC requirements
are stringent, requiring periodic testing
under load and automatic transfer to
emergency power supply on loss of
normal supply. See Figure 1.4-23.
All wiring from emergency source to
emergency loads must be kept separate
from all other wiring and equipment,
in its own distribution and raceway
system, except in transfer equipment
enclosures and similar locations. The
most common power source for large
emergency loads is an engine-generator
set, but the NEC also permits the
emergency supply (subject to local code
requirements) to be storage batteries,
uninterruptible power supplies, a
separate emergency service, or a
connection to the service ahead of the
normal service disconnecting means.
Unit equipment for emergency illumination, with a rechargeable battery,
Emergency Power
Most areas have requirements
for emergency and standby power
systems. The National Electrical Code
does not specifically call for any
emergency or standby power, but
does have requirements for those
systems when they are legally
mandated and classed as emergency
(Article 700), legally required standby
(Article 701) by municipal, state,
federal or other codes, or by any
Legally required standby systems, as

required by the governmental agency
having jurisdiction, are intended to
supply power to selected loads, other
than those classed as emergency
systems, on loss of normal power.
These are usually loads not essential
to human safety, but loss of which
could create hazards or hamper
rescue or fire-fighting operations.
i
ii
1
2
3
4
5
6
7
8
9
Utility
Source
Typical Application: Three engine generator sets serve the load, plus one additional engine
generator set for redundancy to achieve N+1 level of performance. Open or Closed transition is available.
G1
G2
G3
G4
10
11
Paralleling Switchgear
with Distribution
Revenue
Metering
12
HMI
Touchscreen
52G1
52G2
52G3
52G4
Main
Service
D1
D2
D3
13
D4
14
15
16
To Normal
Distribution
Circuits
ATS1
To Emergency
Circuits
ATS2
EDP1
ATS3
EDP2
ATS4
EDP3
17
18
EDP4
19
Optional Remote PC
with Software
LP1
BP1
LP2
BP2
LP3
BP3
LP4
BP4
20
Figure 1.4-23. Typical Emergency Power System
21
CA08104001E

April 2016
Sheet 01 092
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
NEC requirements are similar to those

for emergency systems, except that
wiring may occupy the same distribution and raceway system as the
normal wiring if desired. Optional
standby systems are those not legally
required, and are intended to protect
private business or property where
life safety does not depend on
performance of the system. Optional
systems can be treated as part of the
normal building wiring system. Both
legally required and optional standby
systems should be installed in such
a manner that they will be fully available on loss of normal power. It is
preferable to isolate these systems
as much as possible, even though not
required by code.
Where the emergency or standby
source, such as an engine generator
or separate service, has capacity to
supply the entire system, the transfer
scheme can be either a full-capacity
automatic transfer switch, or, less
costly but equally effective, normal
and emergency main circuit breakers,
electrically interlocked such that on
failure of the normal supply the
emergency supply is connected to the
load. However, if the emergency or
standby source does not have capacity
for the full load, as is usually the
case, such a scheme would require
automatic disconnection of the
nonessential loads before transfer.
Simpler and more economical in
such a case is a separate emergency
bus, supplied through an automatic
transfer switch, to feed all critical
loads. The transfer switch connects
this bus to the normal supply, in
normal operation. On failure of the
normal supply, the engine-generator
is started, and when it is up to speed
the automatic switch transfers the
emergency loads to this source. On
return of the normal source, manual or
automatic retransfer of the emergency
loads can take place.
Peak Shaving
Many installations now have
emergency or standby generators.
In the past, they were required for
hospitals and similar locations, but
not common in office buildings or
shopping centers. However, many
costly and unfortunate experiences
during utility blackouts in recent years
have led to the more frequent installation of engine generators in commercial and institutional systems for safety
and for supplying important loads.
Industrial plants, especially in process

industries, usually have some form
of alternate power source to prevent
extremely costly shutdowns. These
standby generating systems are
critical when needed, but they are
needed only infrequently. They
represent a large capital investment.
To be sure that their power will be
available when required, they should
be tested periodically under load.
The cost of electric energy has risen
to new high levels in recent years, and
utilities bill on the basis not only of
power consumed, but also on the
basis of peak demand over a small
interval. As a result, a new use for
in-house generating capacity has
developed. Utilities measure demand
charges on the basis of the maximum
demand for electricity in any given
specific period (typically 15 or 30
minutes) during the month. Some
utilities have a demand ratchet clause
that will continue demand charges on
a given peak demand for a full year,
unless a higher peak results in even
higher charges. One large load, coming
on at a peak time, can create higher
electric demand charges for a year.
Obviously, reducing the peak demand
can result in considerable savings in
the cost of electrical energy. For those
installations with engine generators
for emergency use, modern control
systems (computers or programmable
controllers) can monitor the peak
demand, and start the engine-generator
to supply part of the demand as it
approaches a preset peak value. The
engine-generator must be selected
to withstand the required duty cycle.
The simplest of these schemes transfer
specific loads to the generator. More
complex schemes operate the generator
in parallel with the normal utility supply.
The savings in demand charges can
reduce the cost of owning the emergency generator equipment.
In some instances, utilities with little
reserve capacity have helped finance
the cost of some larger customerowned generating equipment. In
return, the customer agrees to take
some or all of his load off the utility
system and on to his own generator at
the request of the utility (with varying
limitations) when the utility load
approaches capacity. In some cases,
the customers generator is paralleled
with the utility to help supply the peak
utility loads, with the utility buying
the supplied power. Some utilities
have been able to delay large capital
expenditures for additional generating
capacity by such arrangements.
It is important that the electrical system designer providing a substantial

source of emergency and standby
power investigate the possibility of
using it for peak shaving, and even
of partial utility company financing.
Frequently, substantial savings in
power costs can be realized for a
small additional outlay in distribution
and control equipment.
Peak shaving equipment operating in
parallel with the utility are subject to the
comments made under cogeneration
as to separation from the utility under
fault conditions.
Sound Levels
Sound Levels of Electrical Equipment
for Offices, Hospitals, Schools and
Similar Buildings
Insurance underwriters and building
owners desire and require that the
electrical apparatus be installed
for maximum safety and the least
interference with the normal use of
the property. Architects should take
particular care with the designs for
hospitals, schools and similar buildings to keep the sound perception of
such equipment as motors, blowers
and transformers to a minimum.
Even though transformers are
relatively quiet, resonant conditions
may exist near the equipment, which
will amplify their normal 120 Hz hum.
Therefore, it is important that consideration be given to the reduction of
amplitude and to the absorption of
energy at this frequency. This problem
begins in the designing stages of the
equipment and the building. There are
two points worthy of consideration: 1)
What sound levels are desired in the
normally occupied rooms of this building? 2) To effect this, what sound level
in the equipment room and what type
of associated acoustical treatment
will give the most economical
installation overall?
A relatively high sound level in the
equipment room does not indicate
an abnormal condition within the
apparatus. However, absorption may
be necessary if sound originating in
an unoccupied equipment room is
objectionable outside the room.
Furthermore, added absorption
material usually is desirable if
there is a build-up of sound
due to reflections.
CA08104001E

April 2016
1.4-37
Sheet 01 093

Some reduction or attenuation takes
place through building walls, the
remainder may be reflected in various
directions, resulting in a build-up or
apparent higher levels, especially if
resonance occurs because of room
dimensions or material characteristics.
Area Consideration
In determining permissible sound levels within a building, it is necessary to
consider how the rooms are to be used
and what levels may be objectionable
to occupants of the building. The
ambient sound level values given in
Table 1.4-10 are representative average
values and may be used as a guide in
determining suitable building levels.
Decrease in sound level varies at an
approximate rate of 6 dB for each
doubling of the distance from the
source of sound to the listener. For
example, if the level 6 ft (1.8 m) from
a transformer is 50 dB, the level at a
distance of 12 ft (3.7 m) would be 44 dB
and at 24 ft (7.3 m) the level decreases
to 38 dB, etc. However, this rule applies
only to equipment in large areas
equivalent to an out-of-door installation,
with no nearby reflecting surfaces.
Table 1.4-10. Typical Sound Levels
Description
Average
Decibel
Level (dB)
Radio, recording and TV studios

Theatres and music rooms
Hospitals, auditoriums and churches
2530
3035
3540
Classrooms and lecture rooms

Apartments and hotels
Private offices and conference rooms
3540
3545
4045
Stores
Residence (radio, TV off)
and small offices
Medium office (3 to 10 desks)
4555
Residence (radio, TV on)

Large store (5 or more clerks)
Factory office
60
61
61
Large office
Average factory
Average street
64
70
80
53
58
Table 1.4-11. Maximum Average Sound Levels for Medium Voltage TransformersDecibels
kVA
Liquid-Filled Transformers
Dry-Type Transformers
Self-Cooled
Rating (OA)
Forced-Air
Cooled Rating (FA)
Self-Cooled
Rating (AA)
Forced-Air
Cooled Rating (FA)
300
500
750
55
56
57
67
58
60
64
67
67
67
1000
1500
2000
58
60
61
67
67
67
64
65
66
67
68
69
2500
3000
3750
62
63
64
67
67
67
68
68
70
71
71
73
5000
6000
7500
65
66
67
67
68
69
71
72
73
73
74
75
10,000
68
70
76
Because values given in Table 1.4-11

are in general higher than those given
in Table 1.4-10, the difference must be
attenuated by distance and by proper
use of materials in the design of the
building. An observer may believe
that a transformer is noisy because
the level in the room where it is
located is high. Two transformers of
the same sound output in the same
room increase the sound level in the
room approximately 3 dB, and three
transformers by about 5 dB, etc.
Sounds due to structure-transmitted
vibrations originating from the transformer are lowered by mounting the
transformers on vibration dampeners
or isolators. There are a number of
different sound vibration isolating
materials that may be used with
good results. Dry-type power transformers are often built with an isolator
mounted between the transformer
support and case members. The
natural period of the core and coil
structure when mounted on vibration
dampeners is about 10% of the fundamental frequency. The reduction in the
transmitted vibration is approximately

98%. If the floor or beams beneath
the transformer are light and flexible,
the isolator must be softer or have
improved characteristics in order to
keep the transmitted vibrations to a
minimum. (Enclosure covers and
ventilating louvers are often improperly tightened or gasketed and
produce unnecessary noise.) The
building structure will assist the
dampeners if the transformer is
mounted above heavy floor members
or if mounted on a heavy floor slab.
Positioning of the transformer in
relation to walls and other reflecting
surfaces has a great effect on reflected
noise and resonances. Often, placing
the transformer at an angle to the wall,
rather than parallel to it, will reduce
noise. Electrical connections to a
substation transformer should
be made with flexible braid or
conductors; connections to an
individually mounted transformer
should be in flexible conduit.
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Transformer Sound Levels

Transformers emit a continuous
120 Hz hum with harmonics when
connected to 60 Hz circuits. The
fundamental frequency is the hum
that annoys people primarily because
of its continuous nature. For purposes
of reference, sound measuring
instruments convert the different
frequencies to 1000 Hz and a 40 dB
level. Transformer sound levels based
on NEMA publication TR-1 are listed
in Table 1.4-11.
17
18
19
20
21
CA08104001E

April 2016
Sheet 01 094
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
1.5-1
Sheet 01 095
IEEE Protective Relay Numbers

Table 1.5-1. Selected IEEE Device Numbers for Switchgear Apparatus
Device
Number
Function
Definition
Typical
Uses
Time-delay starting or closing relay
A device that functions to give a desired amount

of time delay before or after any point of operation
in a switching sequence or protective relay system,
except as specifically provided by device functions
48, 62 and 79 described later.
Used for providing a time-delay for

re-transfer back to the normal source
in an automatic transfer scheme.
Starting circuit breaker
A device whose principal function is to connect

a machine to its source of starting voltage.
19
Starting to running transition timer
A device that operates to initiate or cause the

automatic transfer of a machine from the starting
to the running power connection.
Used to transfer a reduced voltage

starter from starting to running.
21
Distance relay
A device that functions when the circuit

admittance, impedance or reactance increases or
decreases beyond predetermined limits.
23
Temperature control device
A device that functions to raise or to lower the

temperature of a machine or other apparatus, or
of any medium, when its temperature falls below
or rises above, a predetermined level.
Used as a thermostat to control

space heaters in outdoor equipment.
24
Volts per hertz relay
A device that operates when the ratio of voltage

to frequency is above a preset value or is below
a different preset value. The relay may have any
combination of instantaneous or time delayed
characteristics.
A device that operates when two AC circuits are

within the desired limits of frequency, phase angle
or voltage, to permit or cause the paralleling of
these two circuits.
In a closed transition breaker

transfer, a 25 relay is used to ensure
two-sources are synchronized before
paralleling. Eaton FP-5000/EDR-5000
feeder protective relays.
27
Undervoltage relay
A device which functions on a given value of

undervoltage.
Used to initiate an automatic transfer

when a primary source of power is lost.
Eaton FP-5000/FP-4000/MP-4000/
EDR-5000/EDR-4000 protective relays.
33
34
Directional power relay
Position switch
Master sequence device
3
4
Synchronizing or synchronism check device
32
25
Annunciator relay
ii
1
30
A non-automatically reset device that gives a

number of separate visual indications upon the
functioning of protective devices, and which may
also be arranged to perform a lockout function.
Used to remotely indicate that a

protective relay has functioned, or
that a circuit breaker has tripped.
Typically, a mechanical drop type
annunciator panel is used.
A relay that functions on a desired value of power

flow in a given direction, or upon reverse power
resulting from arc back in the anode or cathode
circuits of a power rectifier.
Used to prevent reverse power from

feeding an upstream fault. Often
used when primary backup generation
is used in a facility. Eaton FP-5000/
EDR-5000 protective relays.
A device that makes or breaks contact when the

main device or piece of apparatus, which has no
device function number, reaches a given point.
Used to indicate the position of a

drawout circuit breaker (TOC switch).
A device such as a motor-operated multi-contact
switch, or the equivalent, or a programmable

device, that establishes or determines the operating
sequence of the major devices in equipment
during starting and stopping, or during sequential
switching operations.
Eaton MP-3000/MP-4000/EMR-3000
motor protective relays.
7
8
9
10
11
12
13
14
15
37
Undercurrent or underpower relay
A relay that functions when the current or power

flow decreases below a predetermined value.
38
Bearing protective device
A device that functions on excessive bearing

Eaton MP-3000/MP-4000 motor
temperature, or on other abnormal mechanical
protective relays.
conditions, such as undue wear, which may
eventually result in excessive bearing temperature.
40
Field relay
A device that functions on a given or abnormally
high or low value or failure of machine field current,

or on an excessive value of the reactive component
of armature current in an AC machine indicating
abnormally high or low field excitation.
18
19
41
Field circuit breaker
A device that functions to apply, or to remove,

the field excitation of a machine.
42
Running circuit breaker
A device whose function is to connect a machine

to its source of running or operating voltage.
This function may also be used for a device, such
as a contactor, that is used in series with a circuit
breaker or other fault-protecting means, primarily
for frequent opening and closing of the circuit.
CA08104001E
16
17
20
21

Reference Data
1.5-2
April 2016
Sheet 01 096
Table 1.5-1. Selected IEEE Device Numbers for Switchgear Apparatus (Continued)
Device
Number
Function
Definition
Typical
Uses
43
Manual transfer or selector device
A manually operated device that transfers control

or potential circuits in order to modify the plan of
operation of the associated equipment or of some
of the associated devices.
44
Unit sequence starting relay
A device that functions to start the next available

unit in multiple-unit equipment upon the failure or
non-availability of the normally preceding unit.
46
Reverse-phase, or phase balance,

current relay
A relay that functions when the polyphase

currents are of reverse-phase sequence, or when
the polyphase currents are unbalanced or contain
the negative phase-sequence components above
a given amount.
Eaton FP-5000/FP-4000/EDR-5000/
EDR-4000 feeder protective relays and
MP-3000/MP-4000/EMR-3000 motor
protective relays.
47
Phase-sequence voltage relay
A relay that functions upon a predetermined

value of polyphase voltage in the desired phase
sequence.
Eaton FP-5000/FP-4000/EDR-5000/
EDR-4000 feeder protective relays
and MP-3000/MP-4000 motor
protective relays.
48
Incomplete sequence relay
A relay that generally returns the equipment to the

normal, or off, position and locks it out of the
normal starting, or operating or stopping sequence
is not properly completed within a predetermined
amount of time. If the device is used for alarm
purposes only, it should preferably be designated
as 48 A (alarm).
49
Machine, or transformer, thermal relay
A relay that functions when the temperature of a

machine armature, or other load carrying winding
or element of a machine, or the temperature
of a power rectifier or power transformer
(including a power rectifier transformer) exceeds
a predetermined value.
Eaton MP-3000/MP-4000/EMR-3000/
ETR-4000 motor protective relays.
50
Instantaneous overcurrent,
or rate-of-rise relay
A relay that functions instantaneously on an

excessive value of current, or an excessive rate of
current rise, thus indicating a fault in the apparatus
of the circuit being protected.
Used for tripping a circuit breaker

instantaneously during a high-level
short circuit. Can trip on phasephase (50), phase-neutral (50N),
phase-ground (50G) faults.
Eaton Digitrip 3000, FP-5000/
FP-4000/EDR-5000/EDR-4000/
EDR-3000 protective relays,
MP-3000/MP-4000/EMR-3000/
51
AC time overcurrent relay
A relay with either a definite or inverse time

characteristic that functions when the current in an
AC circuit exceeds a predetermined value.
Used for tripping a circuit breaker

after a time delay during a sustained
overcurrent. Used for tripping a
circuit breaker instantaneously
during a high-level short circuit.
Can trip on phase (51), neutral (51N)
or ground (51G) overcurrents.
Eaton Digitrip 3000, FP-5000/
FP-4000/EDR-5000/EDR-4000/
EDR-3000 protective relays,
MP-3000/MP-4000/EMR-3000/
52
AC circuit breaker
A device that is used to close and interrupt an

AC power circuit under normal conditions or to
interrupt this circuit under fault or emergency
conditions.
17
A term applied typically to medium

voltage circuit breakers, or low
voltage power circuit breakers.
Eaton VCP-W vacuum circuit
breaker, magnum DS low voltage
power circuit breaker
53
Exciter or DC generator relay
A device that forces the DC machine field excitation

to build up during starting or that functions when
the machine voltage has built up to a given value.
18
55
Power factor relay
A relay that operates when the power factor

in an AC circuit rises above or below a
predetermined value.
19
56
Field application relay
A device that automatically controls the application

of the field excitation to an AC motor at some
predetermined point in the slip cycle.
20
59
Overvoltage relay
A relay that functions on a given value of

overvoltage.
ii
3
4
5
6
7
8
9
10
11
12
13
14
15
16
21
Eaton FP-5000/FP-4000/EDR-5000
feeder protective relays and MP-4000
motor protective relay.
Used to trip a circuit breaker,

protecting downstream equipment
from sustained overvoltages.
Eaton FP-5000/FP-4000/EDR-5000
feeder protective relays and MP-4000
motor protective relay.
CA08104001E

Reference Data
April 2016
1.5-3
Sheet 01 097

Device
Number
Function
Definition
Typical
Uses
60
Voltage or current balance relay
A relay that operates on a given difference in

voltage, or current input or output of two circuits.
ii
62
Time-delay stopping or opening relay
A time-delay relay that serves in conjunction with

the device that initiates the shutdown, stopping
or opening operation in an automatic sequence.
Used in conjunction with a 27 device

to delay tripping of a circuit breaker
during a brief loss of primary voltage,
to prevent nuisance tripping.
A switch that operates on given values or on a

given rate of change of pressure.
Used to protect a transformer during

a rapid pressure rise during a short
circuit. This device will typically act
to open the protective devices above
and below the transformer. Typically
used with a 63-X auxiliary relay to
trip the circuit breaker.
63
Pressure switch
64
Ground protective relay
A relay that functions on a failure of the insulation

Used to detect and act on a groundof a machine, transformer or of other apparatus to fault condition. In a pulsing high
ground, or on flashover of a DC machine to ground. resistance grounding system, a 64
device will initiate the alarm.
65
Governor
A device consisting of an assembly of fluid,
electrical or mechanical control equipment used for

regulating the flow of water, steam or other media
to the prime mover for such purposes as starting,
holding speed or load, or stopping.
66
Notching or jogging device
A device that functions to allow only a specified

number of operations of a given device, or
equipment, or a specified number of successive
operations within a given time of each other. It also
functions to energize a circuit periodically or for
fractions of specified time intervals, or that is used
to permit intermittent acceleration or jogging of a
machine at low speeds for mechanical positioning.
Eaton MP-3000/MP-4000/EMR-3000
motor protective relays.
Eaton FP-5000/EDR-5000 feeder

protective relays.
AC directional overcurrent relay
A relay that functions on a desired value of AC

overcurrent flowing in a predetermined direction.
69
Permissive control device
A device that is generally a two-position manually

Used as a remote-local switch for
operated switch that in one position permits the
circuit breaker control.
closing of a circuit breaker, or the placing of
equipment into operation, and in the other position
prevents the circuit breaker to the equipment from
being operated.
72
73
Level switch
DC circuit breaker
Load-resistor contactor
A switch that operates on given values, or on a

given rate of change of level.
A device that is used to close and interrupt a

DC power circuit under normal conditions or to
interrupt this circuit under fault or emergency
conditions.
3
4
5
6
7
8
67
71
Used to indicate a low liquid level within

a transformer tank in order to save
transformers from loss-of-insulation
failure. An alarm contact is available
as a standard option on a liquid level
gauge. It is set to close before an unsafe
condition actually occurs.
9
10
11
12
13
14
A device that is used to shunt or insert a step of
load limiting, shifting or indicating resistance in

a power circuit; to switch a space heater in circuit; or
to switch a light or regenerative load resistor
of a power rectifier or other machine in and out
of circuit.
15
16
74
Alarm relay
A device other than an annunciator, as covered

under device number 30, which is used to operate,
or to operate in connection with, a visible or
audible alarm.
78
Phase-angle measuring relay
A device that functions at a predetermined phase
angle between two voltages, between two currents,

or between voltage and current.
18
79
AC reclosing relay
A relay that controls the automatic closing and

locking out of an AC circuit interrupter.
19
Used to automatically reclose a

circuit breaker after a trip, assuming
the fault has been cleared after the
power was removed from the circuit.
The recloser will lock-out after a
predetermined amount of failed
attempts to reclose.
17
20
21
CA08104001E

Reference Data
1.5-4
April 2016
Sheet 01 098
i
ii
Device
Number
Function
Definition
Typical
Uses
81
Frequency relay
A relay that functions on a predetermined value of

frequencyeither under or over, or on normal
system frequencyor rate of change frequency.
Used to trip a generator circuit

breaker in the event the frequency
drifts above or below a given value.
Eaton FP-5000/FP-4000/EDR-5000/
EDR-4000 feeder protective
relays and MP-4000 motor
protective relay.
83
Automatic selective control or transfer relay
A relay that operates to select automatically

between certain sources or conditions in
equipment, or performs a transfer operation
automatically.
Used to transfer control power

sources in a double-ended
switchgear lineup.
85
Carrier or pilot-wire relay
A device that is operated or restrained by a signal

transmitted or received via any communications
media used for relaying.
86
Locking-out relay
An electrically operated hand, or electrically, reset

relay that functions to shut down and hold an
equipment out of service on the occurrence of
abnormal conditions.
Used in conjunction with protective

relays to lock-out a circuit breaker
(or multiple circuit breakers) after
a trip. Typically required to be
manually reset by an operator before
the breaker can be reclosed.
87
Differential protective relay
A protective relay that functions on a percentage or Used to protect static equipment,

phase angle or other quantitative difference of two such as cable, bus or transformers,
currents or of some other electrical quantities.
by measuring the current differential
between two points. Typically the
upstream and/or downstream circuit
breaker will be incorporated into the
zone of protection. Eaton FP-5000
feeder protective relay (87B) and
MD-3000 protective relay.
90
Regulating device
A device that functions to regulate a quantity or

quantities, such as voltage, current, power, speed,
frequency, temperature and load, at a certain value
or between certain (generally close) limits for
machines, tie lines or other apparatus.
91
Voltage directional relay
A device that operates when the voltage across an

open circuit breaker or contactor exceeds a given
value in a given direction.
94
Tripping or trip-free relay
A relay that functions to trip a circuit breaker,

contactor or equipment, or to permit immediate
tripping by other devices, or to prevent immediate
reclosure of a circuit interrupter, in case it should
open automatically even though its closing circuit
is maintained closed.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
1.5-5
Sheet 01 099
Suggested IEEE Designations for Suffix Letters
Suggested IEEE Designations

for Suffix Letters
Auxiliary Devices
These letters denote separate auxiliary
devices, such as the following:
C
Closing relay/contactor
CL
Auxiliary relay, closed

(energized when main device
is in closed position)
CS
Control switch
Main Device
Other Suffix Letters
The following letters denote the main

device to which the numbered device
is applied or is related:
The following letters cover all other

distinguishing features, characteristics
or conditions not specifically described
in Auxiliary Devices through Main
Device Parts, which serve to describe
the use of the device in the equipment,
such as:
Alarm/auxiliary power
AC
Alternating current
BP
Bypass
BT
Bus tie
Capacitor
DC
Direct current
Down position switch relay
Exciter
Lowering relay
Feeder/field
Opening relay/contactor
Generator/ground
OP
Auxiliary relay, open

(energized when main device
is in open position)
Motor/metering
MOC
Mechanism operated contact
PB
Push button
Synchronizing/secondary
Raising relay
Transformer
UP position switch relay
TOC
Truck-operated contacts
Auxiliary relay
Main Device Parts
Auxiliary relay
Auxiliary relay
These letters denote parts of the

main device, except auxiliary contacts, position switches, limit switches
and torque limit switches:
Actuating Quantities
Automatic
BF
Breaker failure
Close
Decelerating/down
Emergency
Failure/forward
HS
High speed
Local/lower
Manual
Open
OFF
Off
ON
On
Raise/reclosing/remote/reverse
Test/trip
TDC
Time-delay closing contact
TDDO
Time delayed relay coil

drop-out
10
11
Coil/condenser/capacitor
CC
Closing coil/closing contactor
TDO
Time-delay opening contact
HC
Holding coil
TDPU
Time delayed relay coil pickup
Amperes/alternating
Operating motor
THD
Total harmonic distortion
Current
OC
Opening contactor
Frequency/fault
Solenoid
I0
Zero sequence current
SI
Seal-in
I-, I2
Negative sequence current
Target
I+, I1
Positive sequence current
TC
Trip coil
Power/pressure
PF
Power factor
Speed
Temperature
Voltage/volts/vacuum
VAR
Reactive power
VB
Vibration
Watts
ii
These letters indicate the condition or

electrical quantity to which the device
responds, or the medium in which it is
located, such as the following:
2
3
4
5
6
7
8
9
12
13
14
15
16
17
18
19
20
21
CA08104001E
1.5-6

Reference Data
April 2016
Sheet 01 100
Codes and Standards
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Codes and Standards

The National Electrical Code (NEC),
NFPA Standard No. 70, is the most
prevalent electrical code in the United
States. The NEC, which is revised every
three years, has no legal standing of
its own, until it is adopted as law by
a jurisdiction, which may be a city,
county or state. Most jurisdictions
adopt the NEC in its entirety; some
adopt it with variations, usually more
rigid, to suit local conditions and
requirements. A few large cities, such
as New York and Chicago, have their
own electrical codes, basically similar
to the NEC. The designer must determine which code applies in the area
of a specific project.
The Occupational Safety and Health
Act (OSHA) of 1970 sets uniform
national requirements for safety in the
workplaceanywhere that people are
employed. Originally OSHA adopted
the 1971 NEC as rules for electrical
safety. As the NEC was amended every
three years, the involved process for
modifying a federal law such as OSHA
made it impossible for the act to adopt
each new code revision. To avoid this
problem, the OSHA administration
in 1981 adopted its own code, a condensed version of the NEC containing
only those provisions considered
related to occupational safety. OSHA
was amended to adopt this code,
based on NFPA Standard 70E, Part 1,
which is now federal law.
The NEC is a minimum safety
standard. Efficient and adequate
design usually requires not just
meeting, but often exceeding NEC
requirements to provide an effective,
reliable, economical electrical system.
Many equipment standards have been
established by the National Electrical
Manufacturers Association (NEMA)
and the American National Standards
Institute (ANSI). Underwriters
Laboratories (UL) has standards that
equipment must meet before UL will
list or label it. Most jurisdictions and
OSHA require that where equipment
listed as safe by a recognized laboratory is available, unlisted equipment
may not be used. UL is by far the most
widely accepted national laboratory,
although Factory Mutual Insurance
Company lists some equipment, and
a number of other testing laboratories

have been recognized and accepted.
The Institute of Electrical and Electronic
Engineers (IEEE) publishes a number
of books (the color book series) on
recommended practices for the design
of industrial buildings, commercial
buildings, emergency power systems,
grounding, and the like. Most of these
IEEE standards have been adopted as
ANSI standards. They are excellent
guides, although they are not in any
way mandatory.
A design engineer should conform

to all applicable codes, and require
equipment to be listed by UL or
another recognized testing laboratory
wherever possible, and to meet
ANSI or NEMA standards. ANSI/IEEE
recommended practices should
be followed to a great extent. In
many cases, standards should be
exceeded to get a system of the
quality required. The design goal
should be a safe, efficient, longlasting, flexible and economical
Professional Organizations
American National Standards Institute
(ANSI)
National Electrical Manufacturers

Association (NEMA)
Headquarters:
1300 North 17th Street

Suite 1847
Rosslyn, VA 22209
703-841-3200
1819 L Street, NW
6th Floor
Washington, DC 20036
202-293-8020
Operations:
25 West 43rd Street
4th Floor
New York, NY 10036
212-642-4900
www.nema.org
National Fire Protection Association

(NFPA)
1 Battery March Park
Quincy, MA 02169-7471
617-770-3000
www.ansi.org
www.nfpa.org
Institute of Electrical and Electronic

Engineers (IEEE)
Underwriters Laboratories (UL)
Headquarters:
3 Park Avenue
17th Floor
New York, NY 10016-5997
212-419-7900
Operations:
445 Hoes Lane
Piscataway, NJ 08854-1331
732-981-0060
www.ieee.org
International Association of Electrical

Inspectors (IAEI)
901 Waterfall Way
Suite 602
Richardson, TX 75080-7702
972-235-1455
333 Pfingsten Road

Northbrook, IL 60062-2096
847-272-8800
www.ul.com
International Code Council (ICC)

5203 Leesburg Pike
Suite 600
Falls Church, VA 22041
1-888-422-7233
www.iccsafe.org
The American Institute of Architects (AIA)

1735 New York Avenue, NW
Washington, DC 20006-5292
202-626-7300
www.aia.org
www.iaei.org
20
21
CA08104001E

Reference Data
April 2016
1.5-7
Sheet 01 101
Motor Protective Device Data
Motor Protection
Consistent with the 2011 NEC
430.6(A)(1) circuit breaker, HMCP and
fuse rating selections are based on
full load currents for induction motors
running at speeds normal for belted
motors and motors with normal
torque characteristics using data taken
from NEC Table 430.250 (three-phase).
Actual motor nameplate ratings shall
be used for selecting motor running
overload protection. Motors built
special for low speeds, high torque
characteristics, special starting
conditions and applications will
require other considerations as
defined in the application section
of the NEC.
These additional considerations may
require the use of a higher rated HMCP,
or at least one with higher magnetic
pickup settings.
Circuit breaker, HMCP and fuse
ampere rating selections are in
line with maximum rules given in
NEC 430.52 and Table 430.250. Based
on known characteristics of Eaton type
breakers, specific units are recommended. The current ratings are no
more than the maximum limits set by
the NEC rules for motors with code
letters F to V or without code letters.
Motors with lower code letters will
require further considerations.
In general, these selections were
based on:
1. Ambientoutside enclosure not
more than 40 C (104 F).
2. Motor startinginfrequent
starting, stopping or reversing.
3. Motor accelerating time
10 seconds or less.
4. Locked rotormaximum 6 times
motor FLA.
Type HMCP motor circuit protector
may not set at more than 1300% of
the motor full-load current to comply
with NEC 430.52. (Except for NEMA
Design B energy high-efficiency
motors that can be set up to 1700%.)
Circuit breaker selections are based
on types with standard interrupting
ratings. Higher interrupting rating types
may be required to satisfy specific
system application requirements.
Table 1.5-2. Motor Circuit Protector (MCP), Circuit Breaker and Fusible Switch Selection Guide
Horsepower
Full Load
Amperes
(NEC) FLA
Fuse Size NEC 430.52

Maximum
Amperes
Recommended Eaton
Circuit
Breaker
Motor Circuit
Protector Type HMCP
Time Delay
Amperes
Amperes
Non-Time Delay
Adj. Range
i
ii
230 V, Three-Phase
1
1-1/2
2
3
3.6
5.2
6.8
9.6
10
10
15
20
15
20
25
30
15
15
15
20
7
15
15
30
2170
45150
45150
90300
5
7-1/2
10
15
15.2
22
28
42
30
40
50
80
50
70
90
150
30
50
60
90
30
50
50
70
90300
150500
150500
210700
20
25
30
40
54
68
80
104
100
125
150
200
175
225
250
350
100
125
150
150
100
150
150
150
3001000
4501500
4501500
7502500
50
60
75
100
130
154
192
248
250
300
350
450
400
500
600
800
200
225
300
400
150
250
400
400
7502500
12502500
20004000
20004000
125
150
200
312
360
480
600
700
1000
1000
1200
1600
500
600
700
600
600
600
18006000
18006000
18006000
1
2
3
4
5
6
7
460 V, Three-Phase
1
1-1/2
2
3
1.8
2.6
3.4
4.8
6
6
6
10
6
10
15
15
15
15
15
15
7
7
7
15
2170
2170
2170
45150
5
7-1/2
10
15
7.6
11
14
21
15
20
25
40
25
35
45
70
15
25
35
45
15
30
30
50
45150
90300
90300
150500
20
25
30
40
27
34
40
52
50
60
70
100
90
110
125
175
50
70
70
100
50
70
100
100
150500
210700
3001000
3001000
50
60
75
100
65
77
96
124
125
150
175
225
200
150
300
400
110
125
150
175
150
150
150
150
4501500
7502500
7502500
7502500
125
150
200
156
180
240
300
350
450
500
600
800
225
250
350
250
400
400
12502500
20004000
20004000
575 V, Three-Phase
8
9
10
11
12
13
1
1-1/2
2
3
1.4
2.1
2.7
3.9
3
6
6
10
6
10
10
15
15
15
15
15
3
7
7
7
930
2170
2170
2170
5
7-1/2
10
15
6.1
9
11
17
15
20
20
30
20
30
35
60
15
20
25
40
15
15
30
30
45150
45150
90300
90300
20
25
30
40
22
27
32
41
40
50
60
80
70
90
100
125
50
60
60
80
50
50
50
100
150500
150500
150500
3001000
50
60
75
100
52
62
77
99
100
110
150
175
175
200
250
300
100
125
150
175
100
150
150
150
3001000
7502500
7502500
7502500
18
125
150
200
125
144
192
225
300
350
400
450
600
200
225
300
250
250
400
12502500
12502500
20004000
19
For motor full load currents of

208 V and 200 V, increase the
corresponding 230 V motor values
by 10 and 15% respectively.
14
15
16
17
20
21
CA08104001E

Reference Data
1.5-8
April 2016
Sheet 01 102
Motor Protective Device Data
Table 1.5-3. 60 Hz, Recommended Protective Setting for Induction Motors

hp
ii
Full Load Minimum Wire Size

Amperes
75 C Copper Ampacity
(NEC) FLA at 125% FLA
Size
Minimum Conduit Size,

Inches (mm)
Fuse Size NEC 430.52

Maximum Amperes 1
THW
Time
Delay
Amperes
THWN
XHHN
Non-Time
Delay
Recommended Eaton:
Circuit
Breaker 2
Amperes
Motor Circuit
Protector
Amperes
Adjustable Range
115 V, Single-Phase
1
2
3
3/4
1
1-1/2
13.8
16
20
14
14
12
20
20
30
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
25
30
35
45
50
60
30
35
40
2
3
5
7-1/2
24
34
56
80
10
8
4
3
30
50
85
100
0.50 (12.7)
0.75 (19.1)
1.00 (25.4)
1.00 (25.4)
0.50 (12.7)
0.50 (12.7)
0.75 (19.1)
1.00 (25.4)
45
60
100
150
80
110
175
250
50
70
100
150
230 V, Single-Phase
3/4
1
1-1/2
6.9
8
10
14
14
14
20
20
20
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
15
15
20
25
25
30
15
20
25
2
3
5
7-1/2
12
17
28
40
14
12
10
8
20
30
50
50
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
0.75 (19.1)
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
0.50 (12.7)
25
30
50
70
40
60
90
125
30
40
60
80
Two-pole device
not available
1
2
Two-pole device
not available
Consult fuse manufacturers catalog for smaller fuse ratings.

Types are for minimum interrupting capacity breakers. Ensure that the fault duty does not exceed breakers I.C.
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
1.5-9
Sheet 01 103
Chart of Short Circuit Currents for Transformers

Table 1.5-4. Secondary Short-Circuit Current of Typical Power Transformers
208 V, Three-Phase
240 V, Three-Phase
480 V, Three-Phase
600 V, Three-Phase
Transformer
Rating
ThreePhase
kVA and
Impedance
Percent
Maximum
ShortCircuit
kVA
Available
from
Primary
System
300
5%
50,000
100,000
150,000
834
834
834
14,900
15,700
16,000
1700
1700
1700
16,600
17,400
17,700
722
722
722
12,900
13,600
13,900
2900
2900
2900
15,800
16,500
16,800
361
361
361
6400
6800
6900
1400
1400
1400
7800
8200
8300
289
289
289
5200
5500
5600
1200
1200
1200
6400
6700
6800
250,000
500,000
Unlimited
834
834
834
16,300
16,500
16,700
1700
1700
1700
18,000
18,200
18,400
722
722
722
14,100
14,300
14,400
2900
2900
2900
17,000
17,200
17,300
361
361
361
7000
7100
7200
1400
1400
1400
8400
8500
8600
289
289
289
5600
5700
5800
1200
1200
1200
6800
6900
7000
1388
1388
1388
21,300
25,200
26,000
2800
2800
2800
25,900 1203
28,000 1203
28,800 1203
20,000
21,900
22,500
4800
4800
4800
24,800
26,700
27,300
601
601
601
10,000
10,900
11,300
2400
2400
2400
12,400
13,300
13,700
481
481
481
8000
8700
9000
1900
1900
1900
9900
10,600
10,900
1388
250,000
1388
500,000
Unlimited 1388
26,700
27,200
27,800
2800
2800
2800
29,500 1203
30,000 1203
30,600 1203
23,100
23,600
24,100
4800
4800
4800
27,900
28,400
28,900
601
601
601
11,600
11,800
12,000
2400
2400
2400
14,000
14,200
14,400
481
481
481
9300
9400
9600
1900
1900
1900
11,200
11,300
11,500
2080
2080
2080
28,700
32,000
33,300
4200
4200
4200
32,900 1804
36,200 1804
37,500 1804
24,900
27,800
28,900
7200
7200
7200
32,100
35,000
36,100
902
902
902
12,400
13,900
14,400
3600
3600
3600
16,000
17,500
18,000
722
722
722
10,000
11,100
11,600
2900
2900
2900
12,900
14,000
14,500
2080
250,000
2080
500,000
Unlimited 2080
34,400
35,200
36,200
4200
4200
4200
38,600 1804
39,400 1804
40,400 1804
29,800
30,600
31,400
7200
7200
7200
37,000
37,800
38,600
902
902
902
14,900
15,300
15,700
3600
3600
3600
18,500
18,900
19,300
722
722
722
11,900
12,200
12,600
2900
2900
2900
14,800
15,100
15,500
2776
2776
2776
35,900
41,200
43,300
5600
5600
5600
41,500 2406
46,800 2406
48,900 2406
31,000
35,600
37,500
9800
9800
9800
40,600 1203
45,200 1203
47,100 1203
15,500
17,800
18,700
4800
4800
4800
20,300
22,600
23,500
962
962
962
12,400
14,300
15,000
3900
3900
3900
16,300
18,200
18,900
2776
250,000
2776
500,000
Unlimited 2776
45,200
46,700
48,300
5600
5600
5600
50,800 2406
52,300 2406
53,900 2406
39,100
40,400
41,800
9800
9800
9800
48,700 1203
50,000 1203
51,400 1203
19,600
20,200
20,900
4800
4800
4800
24,400
25,000
25,700
962
962
962
15,600
16,200
16,700
3900
3900
3900
19,500
20,100
20,600
4164
4164
4164
47,600
57,500
61,800
8300
8300
8300
55,900 3609
65,800 3609
70,100 3609
41,200
49,800
53,500
14,400
14,400
14,400
55,600 1804
64,200 1804
57,900 1804
20,600
24,900
26,700
7200
7200
7200
27,800 1444
32,100 1444
33,900 1444
16,500
20,000
21,400
5800
5800
5800
22,300
25,800
27,200
4164
250,000
4164
500,000
Unlimited 4164
65,600
68,800
72,500
8300
8300
8300
73,900 3609
77,100 3609
80,800 3609
56,800
59,600
62,800
14,400
14,400
14,400
71,200 1804
74,000 1804
77,200 1804
28,400
29,800
31,400
7200
7200
7200
35,600 1444
37,000 1444
38,600 1444
22,700
23,900
25,100
5800
5800
5800
28,500
29,700
30,900
10
2406
2406
2406
24,700
31,000
34,000
9600
9600
9600
34,300 1924
40,600 1924
43,600 1924
19,700
24,800
27,200
7800
7800
7800
27,500
32,600
35,000
11
250,000
500,000
Unlimited
2406
2406
2406
36,700
39,100
41,800
9600
9600
9600
46,300 1924
48,700 1924
51,400 1924
29,400
31,300
33,500
7800
7800
7800
37,200
39,100
41,300
12
3008
3008
3008
28,000
36,500
40,500
12,000
12,000
12,000
40,000 2405
48,500 2405
52,500 2405
22,400
29,200
32,400
9600
9600
9600
32,000
38,800
42,000
250,000
500,000
Unlimited
3008
3008
3008
44,600
48,100
52,300
12,000
12,000
12,000
56,600 2405
60,100 2405
64,300 2405
35,600
38,500
41,800
9600
9600
9600
45,200
48,100
51,400
3609
3609
3609
30,700
41,200
46,600
14,000
14,000
14,000
44,700 2886
55,200 2886
60,600 2886
24,600
33,000
37,300
11,500
11,500
11,500
36,100
44,500
48,800
250,000
500,000
Unlimited
3609
3609
3609
51,900
56,800
62,800
14,000
14,000
14,000
65,900 2886
70,800 2886
76,800 2886
41,500
45,500
50,200
11,500
11,500
11,500
53,000
57,000
61,700
4511
4511
4511
34,000
47,500
54,700
18,000
18,000
18,000
52,000 3608
65,500 3608
72,700 3608
27,200
38,000
43,700
14,400
14,400
14,400
41,600
52,400
58,100
16
250,000
500,000
Unlimited
4511
4511
4511
62,200
69,400
78,500
18,000
18,000
18,000
80,200 3608
87,400 3608
96,500 3608
49,800
55,500
62,800
14,400
14,400
14,400
64,200
69,900
77,200
17
500
5%
750
5.75%
1000
5.75%
1500
5.75%
2000
5.75%
2500
5.75%
3000
5.75%
3750
5.75%
50,000
100,000
150,000
50,000
100,000
150,000
50,000
100,000
150,000
50,000
100,000
150,000
50,000
100,000
150,000
50,000
100,000
150,000
50,000
100,000
150,000
50,000
100,000
150,000
Rated
Load
Continuous
Current,
Amps
rms Symmetrical Amps
Trans50%
Comformer Motor bined
Alone 1 Load 2
Rated
Load
Continuous
Current,
Amps
Trans100%
Alone 1 Load 2
Rated
Load
Continuous
Current,
Amps
Trans100%
Alone 1 Load 2
Rated
Load
Continuous
Current,
Amps
Trans100%
Alone 1 Load 2
Short-circuit capacity values shown correspond to kVA and impedances shown in this table. For impedances other than these, short-circuit currents
are inversely proportional to impedance.
The motors short-circuit current contributions are computed on the basis of motor characteristics that will give four times normal current.
For 208 V, 50% motor load is assumed while for other voltages 100% motor load is assumed. For other percentages, the motor short-circuit
current will be in direct proportion.
ii
1
2
3
4
5
6
13
14
15
18
19
20
21
CA08104001E

Reference Data
April 2016
Sheet 01 104
Transformer Full Load Amperes
Table 1.5-5. Transformer Full-Load Current, Three-Phase, Self-Cooled Ratings

Voltage, Line-to-Line
kVA
ii
30
45
75
208
240
480
83.3
125
208
72.2
108
180
312
416
625
271
361
541
135
180
271
36.1
54.1
90.2
600
28.9
43.3
72.2
2400
4160
7200
12,000
12,470
13,200
13,800
22,900
34,400
7.22
10.8
18.0
4.16
6.25
10.4
2.41
3.61
6.01
1.44
2.17
3.61
1.39
2.08
3.47
1.31
1.97
3.28
1.26
1.88
3.14
0.75
1.13
1.89
0.50
0.76
1.26
108
144
217
27.1
36.1
54.1
15.6
20.8
31.2
9.02
12.0
18.0
5.41
7.22
10.8
5.21
6.94
10.4
4.92
6.56
9.84
4.71
6.28
9.41
2.84
3.78
5.67
1.89
2.52
3.78
72.2
120
180
41.6
69.4
104
24.1
40.1
60.1
14.4
24.1
36.1
48.1
72.2
96.2
13.9
23.1
34.7
46.3
69.4
92.6
7.56
12.6
18.9
25.2
37.8
50.4
5.04
8.39
12.6
16.8
25.2
33.6
63.0
75.6
94.5
42.0
50.4
62.9
112-1/2
150
225
300
500
750
833
1388
2082
722
1203
1804
361
601
902
289
481
722
3
4
1000
1500
2000
2500
3000
3750
2776
4164
2406
3608
4811
1203
1804
2406
3007
3609
4511
962
1443
1925
2406
2887
3608
241
361
481
601
722
902
139
208
278
347
416
520
5000
7500
10,000
4811
1203
1804
2406
694
1041
1388
80.2
120
160
13.1
21.9
32.8
43.7
65.6
87.5
12.6
20.9
31.4
41.8
62.8
83.7
200
241
301
120
144
180
116
139
174
109
131
164
105
126
157
401
601
802
241
361
481
231
347
463
219
328
437
209
314
418
126
189
252
83.9
126
168
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
1.5-11
Sheet 01 105
Impedances Data
Approximate Impedance Data

Table 1.5-6. Typical Impedances
Three-Phase Transformers Liquid-Filled 1
kVA
Network
Padmount
37.5
45
50
75
112.5
150
3.4
3.4
3.4
225
300
500
5.00
5.00
3.4
3.4
4.6
5.00
5.00
7.00
7.00
7.00
5.75
5.75
5.75
3750
5000
6.00
6.50
Values are typical. For guaranteed values,

refer to transformer manufacturer.
Table 1.5-7. 15 kV Class Primary

Oil Liquid-Filled Substation Transformers
kVA
%Z
%R
%X
X/R
65 C Rise
112.5
150
225
5.00
5.00
5.00
1.71
1.88
1.84
4.70
4.63
4.65
2.75
2.47
2.52
300
500
750
5.00
5.00
5.75
1.35
1.50
1.41
4.81
4.77
5.57
3.57
3.18
3.96
1000
1500
2000
5.75
5.75
5.75
1.33
1.12
0.93
5.59
5.64
5.67
4.21
5.04
6.10
2500
5.75
0.86
5.69
6.61
Table 1.5-8. DOE 2016 Transformer

EfficienciesMedium Voltage Three-Phase
Distribution Transformers 1
kVA
%Z
%R
%X
X/R
300
500
750
4.50
5.75
5.75
2.87
2.66
2.47
3.47
5.10
5.19
1.21
1.92
2.11
1000
1500
2000
5.75
5.75
5.75
2.16
1.87
1.93
5.33
5.44
5.42
2.47
2.90
2.81
2500
5.75
1.74
5.48
3.15
300
500
750
4.50
5.75
5.75
1.93
1.44
1.28
4.06
5.57
5.61
2.10
3.87
4.38
1000
1500
2000
5.75
5.75
5.75
0.93
0.87
0.66
5.67
5.68
5.71
6.10
6.51
8.72
2500
5.75
0.56
5.72
10.22
% Efficiency
Liquid- Dry Transformers
Filled
Table 1.5-10. 600 V Primary Class ThreePhase DOE 2016 Energy-Efficient Dry-Type
Distribution Transformers, Aluminum Wound
kVA
Table 1.5-11. 600V Primary Class Three-Phase

DOE 2016 Energy-Efficient Dry-Type
Distribution Transformers, Copper Wound
kVA
80 C Rise
5.75
5.75
5.75
2000
2500
3000
kVA
150 C Rise
Liquid-Filled
750
1000
1500
Table 1.5-9. 15 kV Class Primary

Dry-Type Substation Transformers
%Z
%X
%R
X/R
150 C Rise Aluminum

15
30
45
4.04
2.52
3.75
2.08
1.13
2.64
3.46
2.25
2.67
0.60
0.50
0.99
75
112.5
150
4.05
4.66
3.48
3.34
4.22
3.09
2.29
1.99
1.61
1.46
2.12
1.92
225
300
4.20
4.46
3.96
4.26
1.39
1.32
2.85
3.23
115 C Rise Aluminum

15
30
45
3.77
2.34
4.26
2.08
1.37
3.44
3.14
1.90
2.52
0.66
0.72
1.37
75
112.5
150
4.45
5.17
3.89
3.90
4.81
3.59
2.14
1.89
1.49
1.83
2.54
2.41
225
300
4.90
4.80
4.73
4.65
1.28
1.21
3.69
3.85
80 C Rise Aluminum
15
30
45
4.19
2.50
2.43
2.94
1.76
2.01
2.98
1.78
1.37
0.99
0.99
1.46
75
112.5
150
225
3.11
2.61
2.80
3.35
2.81
2.31
2.64
3.20
1.32
1.21
0.93
0.99
2.12
1.92
2.85
3.23
%Z
%X
%R
X/R
150 C Rise Copper
i
ii
15
30
45
3.10
2.52
3.80
1.59
0.79
2.60
2.66
2.39
2.77
0.60
0.33
0.94
75
112.5
150
2.84
3.63
3.02
1.94
3.11
2.64
2.08
1.88
1.46
0.93
1.66
1.81
225
300
4.34
3.48
3.98
3.19
1.73
1.38
2.31
2.31
115 C Rise Copper
15
30
45
2.90
2.35
3.85
1.59
0.97
2.87
2.43
2.14
2.57
0.66
0.45
1.12
75
112.5
150
2.86
4.02
3.34
2.12
3.59
3.05
1.92
1.82
1.37
1.10
1.97
2.23
225
300
5.03
4.14
4.78
3.94
1.58
1.29
3.02
3.06
80 C Rise Copper
15
30
45
3.09
2.53
1.70
2.04
1.73
1.16
2.32
1.85
1.25
0.88
0.94
0.93
75
112.5
150
225
2.42
2.27
2.89
3.11
2.07
1.98
2.65
2.95
1.25
1.09
1.15
0.96
1.66
1.81
2.31
3.06
6
7
8
9
10
11
12
13
14
All
BILs
2545
kV BIL
4695
kV BIL
M96 kV
BIL
15
30
45
98.65
98.83
98.92
97.5
97.9
98.1
97.18
97.63
97.86
75
112.5
150
99.03
99.11
99.16
98.33
98.52
98.65
98.13
98.36
98.51
225
300
500
99.23
99.27
99.35
98.82
98.93
99.09
98.69
98.81
98.99
98.57
98.69
98.89
17
750
1000
1500
99.40
99.43
99.48
99.21
99.28
99.37
99.12
99.2
99.3
99.02
99.11
99.21
18
2000
2500
99.51
99.53
99.43
99.47
99.36
99.41
99.28
99.33
19
15
16
Based on transformer operating at 50% of

nameplate base kVA.
20
21
CA08104001E

Reference Data
April 2016
Sheet 01 106
Transformer Losses
i
ii
1
2
3
4
5
6
Transformer Loss Data

See product sections for data.
Transformer Losses at Reduced Loads

Information on losses based on actual
transformer test data can be obtained
from the manufacturer. Transformer
manufacturers provide no load watt
losses and total watt losses in accordance with ANSI standards. The
calculated difference between the
no load losses and the total losses
are typically described as the load
losses. Although transformer coils
are manufactured with either aluminum
or copper conductors, the industry
has sometimes referred to these load
losses as the copper losses.
Transformer losses for various

loading can be estimated in the
following manner. The no load watt
losses of the transformer are due to
magnetization and are present
whenever the transformer is
energized. The load watt losses are
the difference between the no load
watt losses and the full load watt
losses. The load watt losses are
proportional to I2R and can be
estimated to vary with the transformer
load by the square of the load current.
At 0% load:
1800 watts
For example, the approximate watts

loss data for a 1000 kVA oil-filled
substation transformer is shown in
the table as having 1800 watts no
load losses and 15,100 watts full load
losses, so the load losses are approximately 13,300 watts (15,1001800). The
transformer losses can be calculated
for various loads as follows.
Because transformer losses vary

between designs and manufacturers,
additional losses such as from
cooling fans can be ignored for
these approximations.
At 50% load:
1800 watts + (13,300)(0.5)2 =
1800 watts + 3325 watts = 5125 watts
At 100% load:
1800 watts + 13,300 watts = 15,100 watts
At 110% load:
1800 watts + (13,300)(1.1)2 =
1800 watts + 16,093 watts = 17,893 watts
Note: 1 watthour = 3.413 Btu.
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
1.5-13
Sheet 01 107
Power Equipment Losses and Enclosures/Knockout Dimensions
Power Equipment Losses
Enclosures
Table 1.5-12. Power Equipment Losses
The following are reproduced from NEMA 250.
Equipment
Watts
Loss
Medium Voltage Switchgear (Indoor, 5 and 15 kV)

1200 A breaker
2000 A breaker
3000 A breaker
4000 A breaker
600
1400
2100
3700
Medium Voltage Switchgear (Indoor, 5 and 15 kV)

600 A unfused switch
1200 A unfused switch
100 A CL fuses
500
750
840
Medium Voltage Starters (Indoor, 5 kV)

400 A starter FVNR
800 A starter FVNR
600 A fused switch
1200 A fused switch
600
1000
500
800
Table 1.5-13. Comparison of Specific Applications of Enclosures for Indoor Nonhazardous Locations
Provides a Degree of Protection Against the
Following Environmental Conditions
400
1000
1500
3200 A breaker
4000 A breaker
5000 A breaker
2400
3000
4700
Fuse limiters800 A CB
200
500
750
6P
12
12K 13
4
5
Table 1.5-14. Comparison of Specific Applications of Enclosures for Outdoor Nonhazardous Locations
Provides a Degree of Protection Against the

Following Environmental Conditions
Enclosure Type
3
Occasional temporary submersion

Occasional prolonged submersion
High resistance grounding
1200
3S
3R 3
Incidental contact with the enclosed equipment

Rain, snow and sleet 4
Sleet 5
4000
5000
7000
4X
6P
11
Class
72 per foot
91 per foot
103 per foot
Acetylene
Hydrogen, manufactured gas
diethyl ether, ethylene, cyclopropane
I
I
I
144 per foot

182 per foot
203 per foot
Gasoline, hexane, butane, naphtha, propane,

acetone, toluene, isoprene
Metal dust
Carbon black, coal dust, coke dust
I
II
II
Flour, starch, grain dust

Fibers, flyings 7
Methane with or without coal dust
II
III
MSHA
3200 A
4000 A
5000 A
Motor Control Centers (Indoor, 480 V)

NEMA Size 1 starter
NEMA Size 2 starter
NEMA Size 3 starter
39
56
92
NEMA Size 4 starter

NEMA Size 5 starter
Structures
124
244
200
Adjustable Frequency Drives (Indoor, 480 V)
Table 1.5-15. Comparison of Specific Applications of Enclosures for Indoor Hazardous Locations
Provides a Degree of Protection Against
Atmospheres Typically Containing
(For Complete Listing, See NFPA 497M)
1600 A
2000 A
2500 A
10
300
44 per foot
60 per foot
66 per foot
These enclosures may be ventilated.

External operating mechanisms are not required to be operable when the enclosure is ice covered.
External operating mechanisms are operable when the enclosure is ice covered.
800 A
1200 A
1350 A
These enclosures may be ventilated.

These fibers and flying are nonhazardous materials and are not considered the Class III type
ignitable fibers or combustible flyings. For Class III type ignitable fibers or combustible flyings,
see the National Electrical Code, Article 500.
Structures3200 A
Structures4000 A
Structures5000 A
Low Voltage Busway (Indoor, Copper, 480 V)
ii
Occasional temporary submersion

Occasional prolonged submersion
Windblown dust
Hosedown
Corrosive agents
Adjustable frequency drives
4X
Oil and coolant seepage

Oil or coolant spraying and splashing
Corrosive agents
3600
4500
225 A, 42 circuit
11 21 4
Circulating dust, lint, fibers and flyings 2

Settling airborne dust, lint, fibers and flyings 2
Hosedown and splashing water
Fuse truck3200 A CB
Fuse truck4000 A CB
Panelboards (Indoor, 480 V)
Enclosure Type
Incidental contact with the enclosed equipment

Falling dirt
Falling liquids and light splashing
Low Voltage Switchgear (Indoor, 480 V)

800 A breaker
1600 A breaker
2000 A breaker
6
7
Enclosure Types
7 and 8, Class I Groups 6
Enclosure Type
9, Class II Groups 6
10
13
14
For Class III type ignitable fibers or combustible flyings, see the National Electrical Code, Article 500.
Due to the characteristics of the gas, vapor or dust, a product suitable for one class or group may
not be suitable for another class or group unless so marked on the product.
Note: If the installation is outdoors and/or additional protection is required by Tables 1.5-13 and
1.5-14, a combination-type enclosure is required.
> 96%
efficiency
12
15
16
17
18
Note: The information provided on power

equipment losses is generic data intended
to be used for sizing of HVAC equipment.
19
20
21
CA08104001E

Reference Data
April 2016
Sheet 01 108
Power Equipment Losses and Enclosures/Knockout Dimensions
Table 1.5-16. Conversion of NEMA Enclosure Type Ratings to IEC 60529 Enclosure Classification Designations (IP)
(Cannot be Used to Convert IEC Classification Designations to NEMA Type Ratings)
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
1.5-15
Sheet 01 109
Conductor Resistance, Reactance, Impedance
Average Characteristics of
600 V Conductors
Ohms per 1000 ft (305 m)
Resistance and reactance are

phase-to-neutral values, based on
60 Hz AC, three-phase, four-wire
distribution, in ohms per 100 ft
(30 m) of circuit length (not total
conductor lengths)
Based upon conductivity of 100% for
copper, 61% for aluminum
Based on conductor temperatures
of 75 C. Reactance values will
have negligible variation with
temperature. Resistance of both
copper and aluminum conductors
will be approximately 5% lower
at 60 C or 5% higher at 90 C.
Data shown in tables may be
used without significant error
between 60 and 90 C
For interlocked armored cable,
use magnetic conduit data for
steel armor and non-magnetic
conduit data for aluminum armor
The tables below are average characteristics based on data from IEEE
Standard 141-1993. Values from
different sources vary because of
operating temperatures, wire
stranding, insulation materials
and thicknesses, overall diameters,
random lay of multiple conductors
in conduit, conductor spacing, and
other divergences in materials, test
conditions and calculation methods.
These tables are for 600 V 5 kV and
15 kV conductors, at an average
temperature of 75 C. Other parameters are listed in the notes. For
medium voltage cables, differences
among manufacturers are considerably greater because of the wider variations in insulation materials and
thicknesses, shielding, jacketing, overall diameters, and the like. Therefore,
data for medium voltage cables should
be obtained from the manufacturer
of the cable to be used.
Z X R
For busway impedance data, see
Tab 21 of this catalog
For PF (power factor) values less
than 1.0, the effective impedance Ze
is calculated from
Z e R PF X sin (arc cos PF)
Application Notes
For copper cable data, resistance

based on tinned copper at 60 Hz;
600 V and 5 kV nonshielded cable
based on varnished cambric insulation; 5 kV shielded and 15 kV cable
based on neoprene insulation
For aluminum cable data, cable is
cross-linked polyethylene insulated
1
2
3
4
5
6
7
8
In Magnetic Duct
In Non-Magnetic Duct
600 V and 5 kV Non-Shielded
5 kV Shielded and 15 kV
8
8 (solid)
6
6 (solid)
0.811
0.786
0.510
0.496
0.0754
0.0754
0.0685
0.0685
0.814
0.790
0.515
0.501
0.811
0.786
0.510
0.496
0.0860
0.0860
0.0796
0.0796
0.816
0.791
0.516
0.502
0.811
0.786
0.510
0.496
0.0603
0.0603
0.0548
0.0548
0.813
0.788
0.513
0.499
0.811
0.786
0.510
0.496
0.0688
0.0688
0.0636
0.0636
4
4 (solid)
2
1
1/0
2/0
3/0
4/0
0.321
0.312
0.202
0.160
0.128
0.102
0.0805
0.0640
0.0632
0.0632
0.0585
0.0570
0.0540
0.0533
0.0519
0.0497
0.327
0.318
0.210
0.170
0.139
0.115
0.0958
0.0810
0.321
0.312
0.202
0.160
0.128
0.103
0.0814
0.0650
0.0742
0.0742
0.0685
0.0675
0.0635
0.0630
0.0605
0.0583
0.329
0.321
0.214
0.174
0.143
0.121
0.101
0.0929
0.321
0.312
0.202
0.160
0.127
0.101
0.0766
0.0633
0.0506
0.0506
0.0467
0.0456
0.0432
0.0426
0.0415
0.0398
0.325
0.316
0.207
0.166
0.134
0.110
0.0871
0.0748
0.321
0.312
0.202
0.160
0.128
0.102
0.0805
0.0640
0.0594
0.0594
0.0547
0.0540
0.814
0.789
0.514
0.500
0.326
0.318
0.209
0.169
0.0552
0.0464
0.0378
0.0356
0.0322
0.0294
0.0257
0.0216
0.0495
0.0493
0.0491
0.0490
0.0480
0.0466
0.0463
0.0495
0.0742
0.0677
0.0617
0.0606
0.0578
0.0551
0.0530
0.0495
0.0557
0.0473
0.0386
0.0362
0.0328
0.0300
0.0264
0.0223
0.0570
0.0564
0.0562
0.0548
0.0538
0.0526
0.0516
0.0497
0.0797
0.0736
0.0681
0.0657
0.0630
0.0505
0.0580
0.0545
0.0541
0.0451
0.0368
0.0342
0.0304
0.0276
0.0237
0.0194
0.0396
0.0394
0.0393
0.0392
0.0384
0.0373
0.0371
0.0356
0.0670
0.0599
0.0536
0.0520
0.0490
0.0464
0.0440
0.0405
0.0547
0.0460
0.0375
0.0348
0.0312
0.0284
0.0246
0.0203
0.0507
0.0504
0.0484
0.0466
0.0456
0.0451
0.0450
0.0438
0.138
0.114
0.0939
0.0792
0.0712
0.0644
0.0586
0.0559
0.0430
0.0421
0.0412
0.0396
0.0531
0.0508
0.0479
0.0445
250
300
350
400
450
500
600
750
ii
Table 1.5-17. 60 Hz Impedance Data for Three-Phase Copper Cable Circuits, in Approximate Ohms per 1000 ft (305 m) at 75 C (a) Three Single Conductors
Wire Size,
AWG or
kcmil
Note: More tables on Page 1.5-16.
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
Sheet 01 110
Conductor Resistance, Reactance, Impedance
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Table 1.5-18. 60 Hz Impedance Data for Three-Phase Copper Cable Circuits, in Approximate Ohms per 1000 ft (305 m) at 75 C (b) Three Conductor Cable
Wire Size,
AWG or
kcmil
In Magnetic Duct and Steel Interlocked Armor
In Non-Magnetic Duct and Aluminum Interlocked Armor
8
8 (solid)
6
6 (solid)
0.811
0.786
0.510
0.496
0.0577
0.0577
0.0525
0.0525
0.813
0.788
0.513
0.499
0.811
0.786
0.510
0.496
0.0658
0.0658
0.0610
0.0610
0.814
0.789
0.514
0.500
0.811
0.786
0.510
0.496
0.0503
0.0503
0.0457
0.0457
0.812
0.787
0.512
0.498
0.811
0.786
0.510
0.496
0.0574
0.0574
0.0531
0.0531
4
4 (solid)
2
1
1/0
2/0
3/0
4/0
0.321
0.312
0.202
0.160
0.128
0.102
0.0805
0.0640
0.0483
0.0483
0.0448
0.0436
0.0414
0.0407
0.0397
0.0381
0.325
0.316
0.207
0.166
0.135
0.110
0.0898
0.0745
0.321
0.312
0.202
0.160
0.128
0.103
0.0814
0.0650
0.0568
0.0508
0.0524
0.0516
0.0486
0.0482
0.0463
0.0446
0.326
0.317
0.209
0.168
0.137
0.114
0.0936
0.0788
0.321
0.312
0.202
0.160
0.127
0.101
0.0766
0.0633
0.0422
0.0422
0.0390
0.0380
0.0360
0.0355
0.0346
0.0332
0.324
0.315
0.206
0.164
0.132
0.107
0.0841
0.0715
0.321
0.312
0.202
0.160
0.128
0.102
0.0805
0.0640
0.0495
0.0495
0.0457
0.0450
0.813
0.788
0.513
0.499
0.325
0.316
0.207
0.166
0.0552
0.0464
0.0378
0.0356
0.0322
0.0294
0.0257
0.0216
0.0379
0.0377
0.0373
0.0371
0.0361
0.0349
0.0343
0.0326
0.0670
0.0598
0.0539
0.0514
0.0484
0.0456
0.0429
0.0391
0.0557
0.0473
0.0386
0.0362
0.0328
0.0300
0.0264
0.0223
0.0436
0.0431
0.0427
0.0415
0.0404
0.0394
0.0382
0.0364
0.0707
0.0640
0.0576
0.0551
0.0520
0.0495
0.0464
0.0427
0.0541
0.0451
0.0368
0.0342
0.0304
0.0276
0.0237
0.0197
0.0330
0.0329
0.0328
0.0327
0.0320
0.0311
0.0309
0.0297
0.0634
0.0559
0.0492
0.0475
0.0441
0.0416
0.0389
0.0355
0.0547
0.0460
0.0375
0.0348
0.0312
0.0284
0.0246
0.0203
0.0423
0.0420
0.0403
0.0389
0.0380
0.0376
0.0375
0.0366
0.135
0.110
0.090
0.0749
0.0666
0.0596
0.0530
0.0505
0.0359
0.0351
0.0344
0.0332
0.0476
0.0453
0.0422
0.0389
250
300
350
400
450
500
600
750
Table 1.5-19. 60 Hz Impedance Data for Three-Phase Aluminum Cable Circuits, in Approximate Ohms per 1000 Ft (305 m) at 90 C (a) Three Single Conductors
Wire Size,
AWG or
kcmil
6
4
2
1
1/0
2/0
3/0
4/0
250
300
350
400
500
600
700
750
1000
In Magnetic Duct
In Non-Magnetic Duct
0.847
0.532
0.335
0.265
0.210
0.167
0.133
0.106
0.053
0.050
0.046
0.048
0.043
0.041
0.040
0.039
0.849
0.534
0.338
0.269
0.214
0.172
0.139
0.113
0.532
0.335
0.265
0.210
0.167
0.132
0.105
0.068
0.063
0.059
0.056
0.055
0.053
0.051
0.536
0.341
0.271
0.217
0.176
0.142
0.117
0.847
0.532
0.335
0.265
0.210
0.167
0.133
0.105
0.042
0.040
0.037
0.035
0.034
0.033
0.037
0.031
0.848
0.534
0.337
0.267
0.532
0.335
0.265
0.054
0.050
0.047
0.535
0.339
0.269
0.0896
0.0750
0.0644
0.0568
0.0459
0.0388
0.0338
0.0318
0.0252
0.0384
0.0375
0.0369
0.0364
0.0355
0.0359
0.0350
0.0341
0.0341
0.0975
0.0839
0.0742
0.0675
0.0580
0.0529
0.0487
0.0466
0.0424
0.0892
0.0746
0.0640
0.0563
0.0453
0.0381
0.0332
0.0310
0.0243
0.0495
0.0479
0.0468
0.0459
0.0444
0.0431
0.0423
0.0419
0.0414
0.102
0.0887
0.0793
0.0726
0.0634
0.0575
0.0538
0.0521
0.0480
0.0894
0.0746
0.0640
0.0563
0.0453
0.0381
0.0330
0.0309
0.0239
0.0307
0.0300
0.0245
0.0291
0.213
0.170
0.137
0.109
0.0945
0.0804
0.0705
0.0634
0.210
0.167
0.132
0.105
0.0891
0.0744
0.0638
0.0560
0.045
0.044
0.042
0.041
0.0396
0.0383
0.0374
0.0367
0.215
0.173
0.139
0.113
0.0975
0.0837
0.0740
0.0700
0.0284
0.0287
0.0280
0.0273
0.0273
0.0535
0.0477
0.0433
0.0412
0.0363
0.0450
0.0377
0.0326
0.0304
0.0234
0.0355
0.0345
0.0338
0.0335
0.0331
0.0573
0.0511
0.0470
0.0452
0.0405
Table 1.5-20. 60 Hz Impedance Data for Three-Phase Aluminum Cable Circuits, in Approximate Ohms per 1000 ft (30 m) at 90 C (b) Three Conductor Cable
Wire Size,
AWG or
kcmil
6
4
2
1
1/0
2/0
3/0
4/0
250
300
350
400
500
600
700
750
1000
In Magnetic Duct and Steel Interlocked Armor
In Non-Magnetic Duct and Aluminum Interlocked Armor
R
0.847
0.532
0.335
0.265
0.210
0.167
0.133
0.106
0.053
0.050
0.046
0.048
0.043
0.041
0.040
0.039
0.849
0.534
0.338
0.269
0.214
0.172
0.139
0.113
0.335
0.265
0.056
0.053
0.340
0.270
0.847
0.532
0.335
0.265
0.042
0.040
0.037
0.035
0.848
0.534
0.337
0.267
0.335
0.265
0.045
0.042
0.338
0.268
0.210
0.167
0.133
0.105
0.050
0.049
0.048
0.045
0.216
0.174
0.141
0.114
0.210
0.167
0.133
0.105
0.034
0.033
0.037
0.031
0.213
0.170
0.137
0.109
0.210
0.167
0.132
0.105
0.040
0.039
0.038
0.036
0.0896
0.0750
0.0644
0.0568
0.0459
0.0388
0.0338
0.0318
0.0252
0.0384
0.0375
0.0369
0.0364
0.0355
0.0359
0.0350
0.0341
0.0341
0.0975
0.0839
0.0742
0.0675
0.0580
0.0529
0.0487
0.0466
0.0424
0.0895
0.0748
0.0643
0.0564
0.0457
0.0386
0.0335
0.0315
0.0248
0.0436
0.0424
0.0418
0.0411
0.0399
0.0390
0.0381
0.0379
0.0368
0.100
0.0860
0.0767
0.0700
0.0607
0.0549
0.0507
0.0493
0.0444
0.0894
0.0746
0.0640
0.0563
0.0453
0.0381
0.0330
0.0309
0.0239
0.0307
0.0300
0.0245
0.0291
0.0284
0.0287
0.0280
0.0273
0.0273
0.0945
0.0804
0.0705
0.0634
0.0535
0.0477
0.0433
0.0412
0.0363
0.0893
0.0745
0.0640
0.0561
0.0452
0.0380
0.0328
0.0307
0.0237
0.0349
0.0340
0.0334
0.0329
0.0319
0.0312
0.0305
0.0303
0.0294
0.214
0.171
0.138
0.111
0.0959
0.0819
0.0722
0.0650
0.0553
0.0492
0.0448
0.0431
0.0378
21
CA08104001E

Reference Data
April 2016
1.5-17
Sheet 01 111
Conductor Ampacities
Current Carrying Capacities of Copper and Aluminum and Copper-Clad Aluminum Conductors
From National Electrical Code (NEC), 2011 Edition (NFPA 70-2011)
Table 1.5-21. Allowable Ampacities of Insulated Conductors Rated 02000 V, 60 to 90 C (140 to 194 F).
ii
Not more than three current-carrying conductors in raceway, cable or earth (directly buried), based on ambient temperature of 30 C (86 F).
Size
Temperature Rating of Conductor (See Table 310.15 [B][16])
AWG or
kcmil
Types
60 C (140 F)
TW, UF
75 C (167 F)
90 C (194 F)
60 C (140 F)
Size
75 C (167 F)
90 C (194 F)
RHW, THHW,
THW, THWN,
XHHW, USE
TBS, SA, SIS,

THHN, THHW,
THW-2, THWN-2,
RHH, RHW-2,
USE-2, XHH,
XHHW, XHHW-2,
ZW-2
Types
RHW, THHW,
THW, THWN,
XHHW, USE, ZW
TBS, SA, SIS, FEP, TW, UF

FEPB, MI,
RHH, RHW-2,
THHN, THHW,
THW-2, THWN-2,
USE-2, XHH,
XHHW, XHHW-2,
ZW-2
Copper
AWG or
kcmil
2
3
4
Aluminum or Copper-Clad Aluminum
18
16
14 1
15
20
14
18
25
12 1
10 1
8
20
30
40
25
35
50
30
40
55
20
25
30
20
30
40
25
35
45
12 1
10 1
8
6
4
3
55
70
85
65
85
100
75
95
110
40
55
65
50
65
75
60
75
85
6
4
3
2
1
1/0
95
110
125
115
130
150
130
150
170
75
85
100
90
100
120
100
115
135
2
1
1/0
2/0
3/0
4/0
145
165
195
175
200
230
195
225
260
115
130
150
135
155
180
150
175
205
2/0
3/0
4/0
250
300
350
215
240
260
255
285
310
290
320
350
170
190
210
205
230
250
230
255
280
250
300
350
400
500
600
280
320
355
335
380
420
380
430
475
225
260
285
270
310
340
305
350
385
400
500
600
700
750
800
385
400
410
460
475
490
520
535
555
310
320
330
375
385
395
420
435
450
700
750
800
900
1000
1250
435
455
495
520
545
590
585
615
665
355
375
405
425
445
485
480
500
545
900
1000
1250
1500
1750
2000
520
545
560
625
650
665
705
735
750
435
455
470
520
545
560
585
615
630
1500
1750
2000
See NEC Section 240.4 (D).
9
10
11
12
13
14
Note: For complete details of using Table 1.5-21, see NEC Article 310 in its entirety.
15
Table 1.5-22. Correction Factors From NFPA 70-2011 (See Table 310.15 [B][2][a])
Ambient
Temperature C
For ambient temperatures other than 30 C (86 F), multiply the allowable ampacities shown
above by the appropriate factor shown below.
Ambient
Temperature F
2125
2630
3135
1.08
1.00
0.91
1.05
1.00
0.94
1.04
1.00
0.96
1.08
1.00
0.91
1.05
1.00
0.94
1.04
1.00
0.96
07077
07886
08795
3640
4145
4650
0.82
0.71
0.58
0.88
0.82
0.75
0.91
0.87
0.82
0.82
0.71
0.58
0.88
0.82
0.75
0.91
0.87
0.82
096104
105113
114122
5155
5660
6170
0.41
0.67
0.58
0.33
0.76
0.71
0.58
0.41
0.67
0.58
0.33
0.76
0.71
0.58
123131
132140
141158
7180
0.41
0.41
159176
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
Sheet 01 112
i
ii
1
2
3
4
5
6
7
Ampacities for Conductors

Rated 02000 V (Excerpted
from NFPA 70-2011, 310.15)
Note: Fine Print Note (FPN) was changed
to Informational Note in the 2011 NEC.
(A) General.
(1) Tables or Engineering Supervision.
Ampacities for conductors shall
be permitted to be determined by
tables as provided in 310.15(B) or
under engineering supervision,
as provided in 310.15(C).
Note: Informational Note No. 1: Ampacities
provided by this section do not take voltage
drop into consideration. See 210.19(A),
Informational Note No. 4, for branch circuits
and 215.2(A), Informational No. 2, for feeders.
Note: Informational Note No. 2: For the
allowable ampacities of Type MTW wire,
see Table 13.5.1 in NFPA 79-2007, Electrical
Standard for Industrial Machinery.
11
(2) Selection of Ampacity. Where

more than one ampacity applies
for a given circuit length, the
lowest value shall be used.
Exception: Where two different
ampacities apply to adjacent
portions of a circuit, the higher
ampacity shall be permitted to
be used beyond the point of
transition, a distance equal to 10 ft
(3.0 m) or 10 percent of the circuit
length figured at the higher
ampacity, whichever is less.
12
Note: Informational Note: See 110.14(C) for

conductor temperature limitations due to
termination provisions.
8
9
10
13
14
15
16
17
18
19
20
21
(B) Tables. Ampacities for conductors

rated 02000 V shall be as specified
in the Allowable Ampacity
Table 310.15(B)(16) through
Table 310.15(B)(19), and
Ampacity Table 310.15(B)(20) and
Table 310.15(B)(21) as modified
by 310.15(B)(1) through (B)(7).
Note: Informational Note: Table
310.15(B)(16) through Table 310.15(B)(19)
are application tables for use in determining
conductor sizes on loads calculated in
accordance with Article 220. Allowable
ampacities result from consideration of one
or more of the following:
(1) Temperature compatibility with

connected equipment, especially
the connection points.
(2) Coordination with circuit and
system overcurrent protection.
(3) Compliance with the requirements
of product listings or certifications.
See 110.3(B).
(4) Preservation of the safety benefits

of established industry practices
and standardized procedures.
(1) General. For explanation of type letters used in tables and for
recognized sizes of conductors for
the various conductor insulations,
see Table 310.104(A) and Table
310.104(B). For installation
requirements, see 310.1 through
310.15(A)(3) and the various
articles of this Code. For flexible
cords, see Table 400.4, Table
400.5(A)(1) and Table 400.5(A)(2).
(3) Adjustment Factors.
(a) More Than Three CurrentCarrying Conductors in a Raceway
or Cable. Where the number of
current-carrying conductors in a
raceway or cable exceeds three, or
where single conductors or multiconductor cables are installed
without maintaining spacing for
a continuous length longer than
24.00-inch (600 mm) and are not
installed in raceways, the allowable
ampacity of each conductor shall be
reduced as shown in Table
310.15(B)(3)(a). Each current-carrying conductor of a paralleled set of
conductors shall be counted as a
current-carrying conductor.
Note: Informational Note No. 1: See Annex
B, Table B.310.15(B)(2)(11), for adjustment
factors for more than three current-carrying
conductors in a raceway or cable with
load diversity.
Note: Informational Note No. 2: See 366.23(A)
for adjustment factors for conductors in
sheet metal auxiliary gutters and 376.22(B)
for adjustment factors for conductors in
metal wireways.
(1) Where conductors are installed in

cable trays, the provisions of
392.80 shall apply.
(2) Adjustment factors shall not apply
to conductors in raceways having
a length not exceeding 24.00-inch
(600 mm).
(3) Adjustment factors shall not apply
to underground conductors entering or leaving an outdoor trench
if those conductors have physical
protection in the form of rigid
metal conduit, intermediate metal
conduit, rigid polyvinyl chloride
conduit (PVC), or reinforced
thermosetting resin conduit (RTRC)
having a length not exceeding
10 ft (3.05 m), and if the number of
conductors does not exceed four.
(4) Adjustment factors shall not

apply to Type AC cable or to
Type MC cable under the following
conditions:
a. The cables do not have an overall
outer jacket.
b. Each cable has not more than three
current-carrying conductors.
c. The conductors are 12 AWG copper.
d. Not more than 20 current-carrying
conductors are installed without
maintaining spacing, are stacked,
or are supported onbridle rings.
(5) An adjustment factor of 60 percent
shall be applied to Type AC cable or
Type MC cable under the following
conditions:
a. The cables do not have an overall
outer jacket.
b. The number of current carrying
conductors exceeds 20.
c. The cables are stacked or bundled
longer that 24.00-inch (600 mm)
without spacing being maintained.
(b) More Than One Conduit, Tube,
or Raceway. Spacing between
conduits, tubing, or raceways
shall be maintained.
(c) Circular Raceways Exposed to
Sunlight on Rooftops.
Where conductors or cables are
installed in circular raceways exposed
to direct sunlight on or above rooftops,
the adjustments shown in Table 1.5-23
shall be added to the outdoor
temperature to determine the
applicable ambient temperature
for application of the correction
factors in Table 310.15(B)(2)(a) or
Table 310.15(B)(2)(b).
Note: Informational Note: One source for
the average ambient temperatures in various
locations is the ASHRAE Handbook
Fundamentals.
Table 1.5-23. NEC (2011) Table 310.15(B)(3)(c)

Ambient Temperature Adjustment for Circular
Raceways Exposed to Sunlight On or
Above Rooftops
Distance Above Roof to
Bottom of Conduit
Temperature
Adder F (C)
00.51-inch (013.0 mm)
60 (33)
Above 0.51-inch (13.0 mm)

3.54-inch (90.0 mm)
40 (22)

11.81-inch (300.0 mm)
30 (17)

36.00-inch (900.0 mm)
25 (14)
CA08104001E
April 2016

Reference Data
1.5-19
Sheet 01 113
(4) Bare or Covered Conductors.
Where bare or covered conductors
are installed with insulated
conductors, the temperature
rating of the bare or covered
conductor shall be equal to the
lowest temperature rating of the
insulated conductors for the
purpose of determining ampacity.
(5) Neutral Conductor.
(a) A neutral conductor that carries
only the unbalanced current from
other conductors of the same
circuit shall not be required to
be counted when applying the
provisions of 310.15(B)(3)(a).
(b) In a three-wire circuit consisting

of two phase conductors and the
neutral conductor of a four-wire,
three-phase, wye-connected
system, a common conductor
carries approximately the same
current as the line-to-neutral load
currents of the other conductors
and shall be counted when applying
the provisions of 310.15(B)(3)(a).
(c) On a four-wire, three-phase wye
circuit where the major portion of
the load consists of nonlinear loads,
harmonic currents are present in
the neutral conductor; the neutral
conductor shall therefore be considered a current-carrying conductor.
(6) Grounding or Bonding Conductor.

A grounding or bonding conductor
shall not be counted when applying
the provisions of 310.15(B)(3)(a).
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
Sheet 01 114
Formulas and Terms
i
ii
1
2
3
4
Table 1.5-24. Formulas for Determining Amperes, hp, kW and kVA

To
Find
Direct
Current
Amperes (l) when

horsepower is known
hp 746
E % eff
kW 1000
Alternating Current
Two-PhaseFour-Wire 1
Three-Phase
kW 1000
E pf
hp 746
2 E % eff pf
kW 1000
2 E pf
kVA 1000
E
l E pf
1000
kVA 1000
2E
l E 2 pf
1000
Single-Phase
Amperes (l) when

kva is known
Kilowatts
IE
1000
kVA
IE
1000
IE2
1000
hp 746
3 E % eff pf
kW 1000
3 E % pf
kVA 1000
3E
l E 3 pf
1000
IE 3
1000
Horsepower (output)
I E % eff
746
I E % eff pf
746
I E 2 % eff pf
746
I E 3 % eff pf
746
Amperes (l) when

kilowatts is known
hp 746
E % eff pf
For two-phase, three-wire circuits, the current in the common conductor is
2 times that in either of the two other conductors.
Note: Units of measurement and definitions for E (volts), I (amperes), and other abbreviations are given below under Common Electrical Terms.
5
6
Common Electrical Terms

= unit of current or rate of flow of electricity
Volt (E)
= unit of electromotive force
Ohm (R)
= unit of resistance
7
8
How to Compute Power Factor
Ampere (l)
E
Ohms law: I = (DC or 100% pf)
R
Megohm
= 1,000,000 ohms
Volt Amperes (VA)
= unit of apparent power

= E l (single-phase)
= El 3
Kilovolt Amperes (kVA) = 1000 volt-amperes
10
Watt (W)
11
12
13
Kilowatt (kW)
= 1000 watts
Power Factor (pf)
= ratio of true to apparent power

W
= --------
VA
Watthour (Wh)
14
15
16
17
18
19
= unit of true power

= VA pf
= 0.00134 hp
kW
---------kVA
Watts
Determining Watts pf = ---------------------------------------------Volts Amperes
1. 1. From watthour meter.

Watts = rpm of disc x 60 x Kh
Where Kh is meter constant
printed on face or nameplate
of meter.
If metering transformers are used,
above must be multiplied by the
transformer ratios.
2. Directly from wattmeter reading.
Where:
Volts = line-to-line voltage as
measured by voltmeter.
Amperes = current measured in
line wire (not neutral) by ammeter.
Table 1.5-25. Temperature Conversion
= unit of electrical work

= 1 watt for 1 hour
= 3.413 Btu
= 2655 ft-lbs
Kilowatt-hour (kWh)
= 1000 watthours
Horsepower (hp)
= measure of time rate of doing work

= equivalent of raising 33,000 lbs 1 ft in 1 minute
= 746 watts
Demand Factor
= ratio of maximum demand to the total connected load
Diversity Factor
= ratio of the sum of individual maximum demands of

the various subdivisions of a system to the maximum
demand of the whole system
Load Factor
= ratio of the average load over a designated period

of time to the peak load occurring in that period
(F to C)
(C to F)
C = 5/9 (F32)
F = 9/5(C)+32
C 15
F
5
10
14
C 25
F 77
30
86
C 65
F 149
5
23
0
32
5
41
35 40 45
95 104 113
70 75
158 167
80 85
176 185
10
50
15
59
20
68
50
55
122 131
60
140
90
95
194 203
100
212
1 Inch
= 2.54 centimeters
1 Kilogram
= 2.20 lbs
1 Square Inch = 1,273,200 circular mills
1 Circular Mill = 0.785 square mil
1 Btu
= 778 ft lbs
= 252 calories
1 Year
= 8760 hours
20
21
CA08104001E
April 2016

Reference Data
1.5-21
Sheet 01 115
Seismic Requirements
i
ii
1
General
In the 1980s, Eaton embarked on a
comprehensive program centered
around designing and building
electrical distribution and control
equipment capable of meeting and
exceeding the seismic load requirements of the Uniform Building Code
(UBC) and California Building Code
(CBC). These codes emphasize building design requirements. Electrical
equipment and distribution system
components are considered attachments to the building. The entire
program has been updated to show
compliance with the 2009 International
Building Code (IBC) and the 2010 CBC
seismic requirements. A cooperative
effort with the equipment user, the
building designer and the equipment
installer ensures that the equipment
is correctly anchored such that it can
withstand the effects of an earthquake.
Eatons electrical distribution and
control equipment has been tested
and seismically proven for requirements exceeding the IBC and CBC.
Over 100 different assemblies
representing essentially all product
lines have been successfully tested
and verified to seismic levels higher
than the maximum seismic requirements specified in the IBC and CBC.
The equipment maintained structural
integrity and demonstrated the ability
to function immediately after the
seismic tests. A technical paper,
Earthquake Requirements and Eaton
Distribution and Control Equipment
Seismic Capabilities (SA12501SE),
provides a detailed explanation
of the applicable seismic codes
and Eatons equipment qualification
program. The paper may be found
at www.eaton.com/seismic. Type
in SA12501SE in the document
search field.
2
3
4
5
6
Figure 1.5-1. Typical Earthquake Ground Motion Map for the United States
International Building Code (IBC)
California Building Code
On December 9, 1994, the International

Code Council (ICC) was established
as a nonprofit organization dedicated
to developing a single set of comprehensive and coordinated codes. The
ICC foundersthe Building Officials
and Code Administrators (BOCA), the
International Conference of Building
Officials (ICBO), and the Southern
Building Code Congress International
(SBCCI)created the ICC in response
to technical disparities among the
three nationally recognized model
codes now in use in the U.S. The
ICC offers a single, complete set of
construction codes without regional
limitationsthe International
Building Code.
The 2001 CBC was based upon the

1997 UBC. In August of 2006, it was
repealed by the California Building
Standards Commission (CBSC) and
replaced by the 2007 CBC, California
Code of Regulations (CCR), Title 24,
Part 2 and used the 2006 IBC as the
basis for the code. The 2010 CBC
is based upon the 2009 IBC, with
amendments as deemed appropriate
by the CBSC. Eatons seismic
qualification program fully envelopes
the requirements of the 2010 CBC.
Uniform Building Code (UBC)

1997 was the final year in which the
UBC was published. It has since been
replaced by the IBC.
Process
According to Chapter 16 of the 2009
IBC, structure design, the seismic
requirements of electrical equipment
in buildings may be computed in two
steps. The first step is to determine
the maximum ground motion to be
considered at the site. The second step
is to evaluate the equipment mounting
and attachments inside the building
or structure. These are then evaluated
to determine appropriate seismic test
requirements. The ground motion,
seismic requirements of the equipment,
and the seismic response spectrum
requirements are discussed on
Page 1.5-23, see Figure 1.5-3.
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
Sheet 01 116
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Ground Motion
According to the code, the first and
most important step in the process
is to determine the maximum
considered earthquake spectral
response acceleration at short
periods of 0.2 seconds (SS) and at
a period of 1.0 second (S1). These
values are determined from a set
of 24 spectral acceleration maps
(Figure 1.5-1) and include numerous
contour lines indicating the severity
of the earthquake requirements at a
particular location in the country.
The spectral acceleration maps
indicate low to moderate seismic
requirements for the entire country,
with the exception of two particular
areas; the West Coast and the Midwest
(the New Madrid area). The seismic
requirements at the New Madrid area
are approximately 30% higher than the
maximum requirements of the West
Coast. The maps also suggest that the
high seismic requirements in both
regions, West Coast and Midwest,
quickly decrease as one moves away
from the fault area. Therefore, the high
requirements are only limited to a
relatively narrow strip along the fault
lines. Just a few miles away from this
strip, only a small percentage of the
maximum requirements are indicated.
Assuming the worse condition, which
is a site directly located near a fault,
the maximum considered earthquake
spectral response acceleration at short
periods of 0.2 seconds (SS) is equal to
285% gravity and at 1.0 second period
(S1) is 124% gravity. These numbers
are the maximum numbers for the
entire country except for the New
Madrid area. These particular sites are
on the border of California and Mexico
(S1) and in Northern California (SS).
To help understand the 2009 IBC (and
2010 CBC) seismic parameters for a
specific building location, the link to
the US Geological Society is extremely
helpful: http://earthquake.usgs.gov/
research/hazmaps/design/
Download the file Java Ground
Motion Parameter Calculatorand
save it to your hard drive, then run the
executable that was downloaded.
The program will allow one to enter
the latitude and longitude of a
location. (One must be connected
to the Internet to run this application,
even after downloading the program.)
The IBC (CBC) seismic parameters for
that location will then be displayed.
SDS, the peak spectral acceleration,

extends between the values of T0 and
TS. T0 and TS are defined in the codes
as follows:
If the latitude and longitude of the

building location is not known,
another convenient Web site is
available that will provide this
information based upon a street
address: http://geocoder.us/
T0 = 0.2 SD1/SDS = 0.2 x 1.24/1.90 =

0.131 seconds (7.63 Hz)
To determine the maximum considered

earthquake ground motion for most
site classes (A through D), the code
introduces site coefficients, which
when applied against the locationspecific site class, produces the
adjusted maximum considered
earthquake spectral response
acceleration for the required site.
The site coefficients are defined as
Fa at 0.2 seconds short period and
FV at 1.0 second period. From the
tables in the code, the highest adjusting factor for SS is equal to 1.0 and the
highest adjusting factor for S1 is 1.50.
TS = SD1/SDS = 1.24/1.90 =
0.653 seconds (1.53 Hz)
According to the IBC and ASCE 7, the
spectral acceleration (Sa) at periods
less than 1.45 seconds may be computed by using the following formula:
Sa = SDS (0.6 T/T0 + 0.4)
Where T is the period where Sa is
being calculated:
Therefore, the acceleration at
0.0417 seconds (24 Hz), for example,
is equal to:
Sa = 1.90 (0.6 (0.0417/0.131) + 0.4) = 1.12 g
As a result, the adjusted maximum

considered earthquake spectral
response for 0.2 second short period
(SMS) and at 1.0 second (SM1), adjusted
for site class effects, are determined
from the following equations:
The acceleration at 0.03 seconds

(33 Hz) is equal to:
Sa = 1.90 (0.6 (0.03/0.131) + 0.4) = 1.02 g
At zero period (infinite frequency),
T = 0.0, the acceleration (ZPA) is
equal to:
SMS = Fa SS = 1.0 x 2.85 g = 2.85 g

SM1 = Fv S1 = 1.5 x 1.24 g = 1.86 g
Sa = 1.90 (0.6 (0.0/0.131) + 0.4) =

0.76 g (ZPA)
ASCE 7 (American Society of Civil

Engineers), Section 11.4, provides a
plot of the final shape of the design
response spectra of the seismic
ground motion. The plot is shown in
Figure 1.5-2. ASCE 7 is referenced
throughout the IBC as the source for
numerous structural design criteria.
The acceleration to frequency

relationship in the frequency range
of 1.0 Hz to TS is stated equal to:
Sa = SD1/T
Where Sa is the acceleration at the
T period.
The design spectral acceleration curve

can now be computed. The peak spectral acceleration (SDS) and the spectral
acceleration at 1.0 second (SD1) may
now be computed from the following
formulas in the code:
At 1.0 Hz (T=1.0) this equation yields

the following acceleration:
Sa = 1.24/1 = 1.24 g
SDS = 2/3 x SMS = 2/3 x 2.85 g = 1.90 g

SD1 = 2/3 x SM1 = 2/3 x 1.8 g = 1.24 g
Spectural Response Acceleration Sa(g)
SDS
Sa =
SD1
T
SD1
Sa =
T0
TS
1.0
Period T (sec)
SD1 TL
T2
TL
Figure 1.5-2. Design Response Spectrum

CA08104001E

Reference Data
April 2016
1.5-23
Sheet 01 117
Testing to accommodate the low end

of the spectra using this acceleration
component can result in testing to a
factor 2 to 3 times greater than that
realistically required.
Through testing experience and data
analysis, the seismic acceleration at
1.0 Hz is taken equal to 0.7 g, which
will ensure that the seismic levels are
achieved well below 3.2 Hz. This yields
a more vigorous test over a wider
range of seismic intensities.
In developing the seismic requirements
above, it is important to recognize
the following:
This completes the ground motion

design response spectrum. The
spectral accelerations are equal to
0.76 g at ZPA, or 33 Hz, and increases
linearly to a peak acceleration of 1.90 g
at 0.09 seconds (or 11.49 Hz) and stays
constant to 0.653 seconds (1.53 Hz),
then gradually decreases to 1.24 g at
1 second (or 1.0 Hz). This curve is
shown in Figure 1.5-3.
It can be seen that Eaton has elected to

develop generic seismic requirements
that envelop two criteria:
The highest possible spectral peak

accelerations and ZPA
The maximum frequency range
required for many different sites
Acceleration (g peak)
Testing has demonstrated that the

lowest dominant natural frequency of
Eatons electrical equipment is above
3.2 Hz. This indicates that testing at
1.24g at 1 Hz is not necessary. In
addition, having the low end of the
spectra higher than realistically
required forces the shake table to
move at extremely high displacements
to meet the spectral acceleration at
the low frequencies.
10
9
8
7
T0 = 0.2 SD1/(SDS x 1.5) = 0.2 x 1.24/(1.90

x 1.5) = 0.087 seconds (11.49 Hz)
Eaton ensures maximum certification
by requiring peak acceleration during
testing to extend to 12 Hz.
ii
1
2
3
Test Response Spectrum

(TRS)
Zero Period
Acceleration = Maximum
Table Test Motion
4
3
Spectrum Dip Not Important

Because Frequency is Not an
Equipment Natural Frequency
1.0
.9
.8
.7
.6
Required Response Spectrum

(RRS)
.5
Zero Period
Acceleration = Maximum
Floor Motion
.4
.3
T0 and TS are dependent on SMS and

SD1. If SD1 is small relative to SMS then
T0 and TS will be smaller and the
associated frequencies will shift
higher. The opposite is also true.
This must be realized in developing
the complete required response
spectrum (RRS). Therefore, it is not
adequate to stop the peak spectral
acceleration at 7.63 Hz. There are other
contour line combinations that will
produce higher T0. To account for this
variation it is almost impossible to
consider all combinations. However,
a study of the spectral acceleration
maps indicates that all variations with
high magnitude of contour lines could
very well be enveloped by a factor
of 1.5. Therefore, T0 is recomputed
as follows:
.2
9
.1
1
4 5 6 78
9 10
20
30
40
60
80
100
Frequency Hz
Figure 1.5-3. Design Response Spectrum
ASCE 7 Section 13.3Seismic

Demands on Non-Structural
Components
ASCE 7 Paragraph 13.3.1 (IBC Section
1621.1.4) provides a formula for
computing the seismic requirements
of electrical and mechanical equipment
inside a building or a structure. The
formula is designed for evaluating the
equipment attachment to the equipment foundations. The seismic loads
are defined as:
Fp = 0.4 ap SDS Wp (1 + 2 Z/h)/(Rp/Ip)
Where:
Fp = Seismic design force imposed
at the components center of gravity
(C.G.) and distributed relative to
component mass distribution.
ap = Component amplification factor
that varies from 1.00 to 2.50.
SDS = Ground level spectral
acceleration, short period.
Wp = Component operating weight.
10
11
Rp = Component response modification factor that for electrical equipment

varies from 2.5 to 6.0.
Ip = Component importance factor that
is either 1.0 or 1.5.
Z = Highest point of equipment in a
building relative to grade elevation.
h = Average roof height of building
relative to grade elevation.
The following parameters produce the
maximum required force:
Z is taken equal to h (equipment

on roof)
Ip is taken equal to 1.5
ap is taken equal to 2.5
Rp is taken equal to 2.5
SDS is equal to 1.90 g as indicated
in the previous section
The acceleration (Fp/Wp) at the C.G.

of the equipment is then computed
equal to:
Acceleration = Fp/Wp = 0.4 x 2.5 x
1.90 g (1 + 2) / (2.5/1.5) = 3.42 g
12
13
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
Sheet 01 118
ii
Acceleration = Fp/Wp = 0.4 x 2.5 x

1.90 g (1 + 0) / (2.5 /1.5) = 1.14 g
It is impractical to attempt to measure

the actual acceleration of the C.G. of a
piece of equipment under seismic test.
The seismic response at the middle of
base mounted equipment close to its
C.G. is at least 50% higher than the
floor input at the equipment natural
frequency. The base accelerations
associated with the accelerations of
FP/WP at the C.G. of the equipment
could then be computed as 3.42 /1.5
= 2.28 g. It is the equipment base input
acceleration that is measured and
documented during seismic testing
and is the acceleration value shown
on Eatons seismic certificates.
2
3
4
5
6
Final Combined Requirements
7
8
9
10
11
12
13
14
To better compare all seismic levels

and determine the final envelope
seismic requirements, the 2010 CBC,
2009 IBC for California, and 2009 IBC
for New Madrid area seismic requirements are plotted in Figure 1.5-4. All
curves are plotted at 5% damping. An
envelopment of the seismic levels in
the frequency range of 3.2 Hz to 100 Hz
is also shown. This level is taken as
Eatons generic seismic test requirements for all certifications. Eaton
performed additional seismic test runs
on the equipment at approximately
120% of the generic enveloping seismic
requirements (see Figure 1.5-5). Eaton
has established this methodology to
provide additional margin to accommodate potential changes with the
spectral maps, thus eliminating the
need for additional testing.
10
IBC 2009/CBC 2010
Acceleration (g)
For equipment on (or below) grade,

the acceleration at the equipment C.G.
is then computed equal to:
IBC 2009 New Madrid
1
Eaton Seismic
0.1
1
10
100
Frequency (Hz)
Figure 1.5-4. Required Response Spectrum Curve

10
Eaton 120% Seismic Envelope
Acceleration (g)
Eaton 100% Seismic Envelope

1
0.1
10
100
Frequency (Hz)
15
Figure 1.5-5. Eaton Test Required Response Spectrum Curve
16
17
18
19
20
21
CA08104001E
April 2016

Reference Data
1.5-25
Sheet 01 119
Product Specific Test Summaries
Table 1.5-26. Distribution Equipment

Tested and Seismically Proven Against
Requirements within IBC 2009
ii
Eaton Equipment
Low voltage metal-enclosed switchgear
DS II
Magnum DS
High resistance ground
Panelboards
Pow-R-Line C 1a, 1a-LX, 2a, 2a-LX, 3a, 3E, 4,
5P, F-16 and Pow-R-Command
Switchboards
Instant
Pow-R-Line 5P
Integrated facilities
Pow-R-Line C
Multimeter
Pow-R-Line i
MCC
IT.
Advantage
Series 2100
FlashGard
Freedom 2100
Low voltage busway
Pow-R-Way and associated fittings
Pow-R-Way III and associated fittings
Dry type transformers
Mini powercenters
EP, EPT, DS-3, DT-3
Transfer switches
Automatic transfer switch equipment
Uninterruptible power supplies (UPS)
Battery modules
UPSs
Enclosed control safety switches
General-duty
Heavy-duty
Elevator control module
Medium voltage switchgear
Type VacClad-W
Type MMVS
MEF
Type MVS/MEB
MV bus
Metal-enclosed non-segregated phase bus
Network protectors
Type CM-22
Type CMD
Medium voltage control
AMPGARD
SC9000 drives
Substation transformers
Dry-type
Liquid type
Unitized dry-type power centers
1
2
3
4
5
6
7
8
9
10
11
12
13
Figure 1.5-6. Sample Seismic Certificate
Note: See www.eaton.com/seismic for

current seismic certificates.
14
15
16
17
18
19
20
21
CA08104001E

Reference Data
April 2016
Sheet 01 120
i
ii
1
2
3
4
5
6
7
8
9
10
11
12
13
Additional Design and

Installation Considerations
When installing electrical distribution
and control equipment, consideration
must be given as to how the methods
employed will affect seismic forces
imposed on the equipment, equipment
mounting surface, and conduits
entering the equipment.
Eaton recommends that when specifying a brand of electrical distribution
and control equipment, the designer
references the installation manuals of
that manufacturer to ascertain that the
requirements can be met through the
design and construction process.
For Eaton electrical distribution and
control products, the seismic installation guides for essentially all product
lines can be found at our Web site:
http://www.eaton.com/seismic.
Electrical designers must work closely
with the structural or civil engineers
for a seismic qualified installation.
Consideration must be given to the
type of material providing anchorage
for the electrical equipment.
If steel, factors such as thickness or

gauge, attachment via bolts or welding,
and the size and type of hardware
must be considered.
If concrete, the depth, the PSI, the type
of re-enforcing bars used, as well as
the diameter and embedment of
anchorage all must be considered.
The designer must also give consideration if the equipment will be secured
to the wall, versus stand-alone or freestanding, which requires the equipment to withstand the highest level of
seismic forces. Top cable entry should
be avoided for large enclosures, as
accommodation for cable/conduit
flexibility will need to be designed
into the system.
For a manufacturer to simply state
Seismic Certified or Seismic
Qualified does not tell the designer
if the equipment is appropriate for
the intended installation.
Note: Eaton recommends that designers
confirm with the manufacturer if the
seismic certification supplied with the
equipment is based on:
1. ACTUAL shaker table test as

required by the IBC and CBC.
2. The seismic certificate and test
data clearly state if the equipment
was tested as free-standing
anchored at the bottom of the
equipment to the shaker table.
3. Structure attached, that is,
anchored at the center of gravity
(C.G.) or at the TOP of the equipment to a simulated wall on the
shaker table.
Stand-Alone or Free-Standing Equipment

If stand-alone or free-standing, then
this may require that additional width
space be allowed at each end of the
equipment for additional seismic
bracing supplied by the manufacturer.
Additional thought must be given to
the clearances around the equipment
to rigid structural edifices. Space must
be allowed for the differing motions of
the equipment and the structure, so
that they do not collide during a seismic event and damage one another.
Note: If the equipment is installed as standalone or free-standing, with additional
seismic bracing at each end and not
attached to the structure as tested, and yet,
it is fitted tightly against a structural wall,
then this would be an incorrect installation
for the application of the seismic certificate.
Furthermore, if conduits are to be

installed overhead into the equipment,
does the design call for flexible conduits
of sufficient length to allow for the
conflicting motion of the equipment
and the structure during a seismic event
so as to not damage the conductors
contained therein, and the terminations
points within the equipment.
Structure Attached Equipment

The designer must work closely
with the structural engineer if the
equipment is to be attached to the
structure to ascertain that the internal
wall re-enforcement of the structure,
type of anchor, and depth of embedment is sufficient to secure the
equipment so that the equipment,
conduits and structure move at or
near the same frequency.
14
15
16
17
18
19
20
21
CA08104001E

Power Distribution System

Uploaded by

Copyright:

Available Formats

Power Distribution System

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Power Distribution System

Uploaded by

Copyright:

Available Formats

Power Distribution Systems

Designing a Distribution System

For more information, visit: www.eaton.com/consultants