Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

090 020-cs Quantum

Download as pdf or txt
Download as pdf or txt
You are on page 1of 140

Form 090.

020-CS (JUNE 2011)


COMUNICATIONS SETUP
File:
Replaces:
Dist:

SERVICE MANUAL - Section 90


090.020 CS (MAR 10)
3, 3a, 3b, 3c

COMMUNICATIONS SETUP

FRICK QUANTUM LX
COMPRESSOR
Version 7.0x

090.020-CS (JUNE 11)


Page 2

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

TABLE OF CONTENTS
SECTION 1

INTRODUCTION TO THE QUANTUM LX...............................................................................................................6


Quantum Description..............................................................................................................................................6
How To Use This Manual............................................................................................................................................6
ETHERNET AND NETWORKING...............................................................................................................................7
Description.................................................................................................................................................................7
Cabling........................................................................................................................................................................7
RJ-45 Connectors ......................................................................................................................................................8
The Hub......................................................................................................................................................................8
The Switch.................................................................................................................................................................8
Ethernet Setup..........................................................................................................................................................10
IP Data......................................................................................................................................................................10
Naming Data.............................................................................................................................................................11
E-Mail Data...............................................................................................................................................................11
Protocols..................................................................................................................................................................11

SECTION 2

SERIAL COMMUNICATIONS..................................................................................................................................13
RS-232 Description...................................................................................................................................................13
RS-422/RS-485 Description......................................................................................................................................13
Serial Communications Setup....................................................................................................................................14
Using The Map File...................................................................................................................................................15
Serial Communication Setup Table............................................................................................................................17
SERIAL PROTOCOL...............................................................................................................................................18
Description................................................................................................................................................................18
Quantum LX Communications Protocol List...........................................................................................................18
Checklist For Setting Up Communication...................................................................................................................18
Frick Protocol........................................................................................................................................................19
Description........................................................................................................................................................19
Frick # Protocol Specifications........................................................................................................................19
Quantum $ Protocol Specifications.................................................................................................................26
Data Packet................................................................................................................................................26

SECTION 3

QUANTUM LX ALLEN-BRADLEY COMMUNICATION............................................................................................35


Overview Of Half And Full Duplex Theory.................................................................................................................35
SLC-500 - Suggested Setup......................................................................................................................................36
Channel Configuration.......................................................................................................................................36
Read Message Setup Example............................................................................................................................36
Write Message Setup Example...........................................................................................................................36
ALLEN-BRADLEY PROGRAMMING OVERVIEW........................................................................................................37
Channel Configuration...............................................................................................................................................37
General Configuration...............................................................................................................................................37
System Configuration................................................................................................................................................38
Message Sequence Logic..........................................................................................................................................38
Message Read Logic.................................................................................................................................................39
Message Read Setup Screen.....................................................................................................................................40
Message Write Logic.................................................................................................................................................41
Message Write Setup Screen.....................................................................................................................................43
Allen-Bradley Data Access.........................................................................................................................................43
Ethernet / IP...............................................................................................................................................................43

SECTION 4

MODBUS PROTOCOL.........................................................................................................................................45
General Description..................................................................................................................................................45
Modbus TCP/IP (Ethernet)......................................................................................................................................45
Modbus ASCII (Serial Communications)...................................................................................................................46
Modbus RTU (Serial Communications)....................................................................................................................46
Serial Port Configuration Of The Master......................................................................................................................46

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 3

Data Packet...............................................................................................................................................................46
The Query.................................................................................................................................................................47
The Response...........................................................................................................................................................47
Data Field..................................................................................................................................................................47
Error Checking..........................................................................................................................................................47
ASCII..................................................................................................................................................................47
RTU...................................................................................................................................................................47
Framing.....................................................................................................................................................................48
ASCII..................................................................................................................................................................48
RTU...................................................................................................................................................................48
ASCII Query (Read) Example......................................................................................................................................49
ASCII Write Example.................................................................................................................................................50
ASCII Response Example...........................................................................................................................................52
RTU Query (Read) Example.......................................................................................................................................53
RTU Response Example.............................................................................................................................................53
Modbus Notes........................................................................................................................................................54
Modbus Data Access.............................................................................................................................................54

SECTION 5

HYPERTERMINAL..................................................................................................................................................55
Description................................................................................................................................................................55
Setting up Hyperterminal..........................................................................................................................................55
Testing Communications...........................................................................................................................................57
General Notes...........................................................................................................................................................58
Conversion Chart For Decimal / Hexadecimal / ASCII................................................................................................59

SECTION 6

QUANTUM LX DATA TABLES..............................................................................................................................61


Digital Board Values..................................................................................................................................................62
Analog Board Values.................................................................................................................................................64
Calculated Values......................................................................................................................................................66
Mode Values..............................................................................................................................................................67
Timer Values.............................................................................................................................................................75
Setpoint Values.........................................................................................................................................................76
Commands................................................................................................................................................................97
DBS Setpoint Values..................................................................................................................................................98
General Setpoint Values............................................................................................................................................99
VSD (Vyper) Setpoint Values.......................................................................................................................................99

SECTION 7

WARNING/SHUTDOWN MESSAGE CODES............................................................................................................103

SECTION 8

Q5 CONTROLLER.................................................................................................................................................110
Main Board History And Identification......................................................................................................................110
Communications Connector Locations.....................................................................................................................110
SERIAL COMMUNICATIONS HARDWARE..............................................................................................................111
General Description.................................................................................................................................................111
COM-1 and COM-2 Description................................................................................................................................111
COM-3 Description..................................................................................................................................................111
COM-4 Description..................................................................................................................................................111
SERIAL COMMUNICATIONS PORT WIRING...........................................................................................................112
General Note...........................................................................................................................................................112
RS-232 Wiring And Jumpers....................................................................................................................................112
RS-422/485 Wiring And Jumpers..............................................................................................................................112
RS-422 Signal Wiring........................................................................................................................................112
RS-485 Signal Wiring........................................................................................................................................112
SERIAL COMMUNICATIONS TROUBLESHOOTING.................................................................................................113
Troubleshooting RS-232..........................................................................................................................................113
Troubleshooting RS-422.........................................................................................................................................113
Troubleshooting RS-484.........................................................................................................................................113
COMMUNICATIONS DATA LOGGING SCREENS......................................................................................................115

090.020-CS (JUNE 11)


Page 4

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

Communications Log...............................................................................................................................................115
Modbus TCP Log......................................................................................................................................................115

SECTION 9

QUANTUM 4 CONTROLLER..................................................................................................................................118
Main Board History And Identification......................................................................................................................118
QUANTUM 4 SERIAL COMMUNICATIONS HARDWARE.........................................................................................119
General Description.................................................................................................................................................119
COM-1 and COM-2 Description................................................................................................................................119
COM-3 Description..................................................................................................................................................119
SERIAL COMMUNICATIONS PORT WIRING...........................................................................................................120
RS-232 Wiring And Jumpers...................................................................................................................................120
RS-422/485 Wiring And Jumpers.............................................................................................................................21
RS-422 Signal Wiring........................................................................................................................................121
RS-485 Signal Wiring........................................................................................................................................122
SERIAL COMMUNICATIONS TROUBLESHOOTING.................................................................................................123
Troubleshooting RS-232..........................................................................................................................................123
Troubleshooting RS-422........................................................................................................................................123
Troubleshooting RS-484........................................................................................................................................124
COMMUNICATIONS DATA LOGGING SCREENS......................................................................................................125
Communications Log...............................................................................................................................................125
Modbus TCP Log.....................................................................................................................................................125
COMMUNICATIONS LOOPBACK TEST..................................................................................................................126
Description..............................................................................................................................................................126
Hardware Setup For Testing
RS-232.............................................................................................................................................................126
RS-422.............................................................................................................................................................126
RS-485.............................................................................................................................................................127
SOFTWARE SETUP FOR THE COMMUNICATIONS LOOPBACK TEST.....................................................................127
Performing The Communications Loopback Test....................................................................................................128

SECTION 10

APPENDIX A.......................................................................................................................................................130
Frick Serial Communications Converter Module...................................................................................................130
Description......................................................................................................................................................130
Setting The Dipswitch......................................................................................................................................130
Mounting The Module.......................................................................................................................................130
Wiring The Module..........................................................................................................................................131
RS-232 Connections..................................................................................................................................131
RS-422 Connections..................................................................................................................................131
RS-485 Connections..................................................................................................................................131
APPENDIX B.......................................................................................................................................................132
Quantum LX Ethernet Communications Wiring....................................................................................................132
APPENDIX C.......................................................................................................................................................133
Quantum LX Local Ethernet Configurations..........................................................................................................133
APPENDIX D.......................................................................................................................................................134
Quantum LX Ethernet Network Configurations.....................................................................................................134
APPENDIX E.......................................................................................................................................................135
Quantum LX Serial Communications Wiring.........................................................................................................135
Serial Communications Wiring Diagrams.................................................................................................................138
To Customer Remote Computer/DCS...............................................................................................................138
RS-485 Communications...........................................................................................................................138
RS-422 Communications...........................................................................................................................138

The Quantum has the capability of being modified by the user/owner in order to obtain different performance characteristics. Any modification to the standard default settings may have a severe negative impact on the operation and performance of the equipment. Any modification to these control settings is the sole responsibility of the user/owner and Johnson
Controls disclaims any liability for the consequences of these modifications. It is possible that the modification of these
settings may cause improper operation and performance that result in property damage, personal injury or death. It is the
responsibility of the user/owner to evaluate and assess the consequences of their actions prior to modifying the controls
for this unit.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 5

SECTION 1
INTRODUCTION TO THE QUANTUM CONTROL SYSTEM

090.020-CS (JUNE 11)


Page 6

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

INTRODUCTION TO THE QUANTUM LX


QUANTUM DESCRIPTION
The Quantum LX control panel currently utilizes two versions of microprocessor hardware, the
Quantum 4 and Q5 boards. The LX portion of
the Quantum name actually refers to the operating system (software), and the operator interface (physical display and keypad). When you
see the name Quantum 4 or Q5, the physical
hardware of the controller is being referred to
(microprocessor), whereas Quantum LX refers
to the software, and how the operator interacts
with the software (through the display/keypad).
As an example, the Quantum 4 and Q5 con-

trollers contain the physical Ethernet and Serial


connections that the user connects to, while the
Quantum LX software determines how those
connections are used. These connections are
known as PROTOCOLS.
The Quantum LX software is based on a Web
Browser format, and has the capability of communication through both Ethernet and Serial
Ethernet protocols.
The following screen is representative of what
the operator will see after the unit has been
powered up. This is called the Home screen. Be
aware that the content of this screen may differ
from situation to situation, based upon the actual
configuration and installed options.

The Operating (or Home) screen

HOW TO USE THIS MANUAL


The purpose of this manual is provide the necessary information (protocols, data registers, wiring, etc.) to allow the end user to reliably communicate with the Quantum LX via various
communications methods (to be described later)
for the purpose of obtaining and sending data
and/or for compressor control.
The Quantum LX does NOT begin any communications conversations on its own, it only
responds to queries (requests) from external devices.
For Ethernet communications, refer to the sec-

tion entitled Ethernet and Networking. Ethernet


does not require any jumpers to be installed.
For serial communications connections, refer to
the section entitled Quantum Serial Communication for the correct wiring and jumper settings
of RS-232, RS-422, or RS-485. Also, refer to the
drawing of the Quantum 4 Main Board section
to identify wiring configurations for Com-2.
For information on software protocols, refer to
the section entitled Protocol Description.
To access specific data within the Quantum LX,
refer to the Data Tables.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

ETHERNET AND NETWORKING


DESCRIPTION
Frick Controls uses Ethernet as the primary
method of connecting one or multiple Quantum LX panels to a common computer network. In the past, this interconnection would
have been done by serial protocol wiring, such
as RS-232/422/485. But with the capabilities of
todays technology, Ethernet is the quickest and
most efficient way of providing this connectivity.
Whereas the old serial communications methods (RS232, etc.) were slow by todays standards
(kilobits per second transmission speed), Ethernet is available in two speeds: 10 Mbps and 100
Mbps.
NOTE: For connection examples, refer to
the section of this manual entitled Quantum LX Local Ethernet Configurations and
Quantum LX Ethernet Network Configurations.
Ethernet is a data and information sharing system. It is a method of connecting one computer
to many others on a common network. This network can consist of both hardwired connections,
and wireless devices, hence the name ETHERNET.
Any Windows or Linux based computer is capable of accessing this network. All that is needed
is either a modem, USB port, or an Ethernet port.
These devices provide the necessary point of
connection for one end (branch) of the connection (a home computer for instance). The other
point that completes the connection is usually
provided by an Internet Service Provider (or ISP).
The Internet Service Provider usually has a very
large network router, or means of bring in many
individual connections. The router then assigns a
discrete and individual address to each connection (much like a street address). This address is
known as an Internet Protocol address (IP). The
IP address consists of a series of 4 to 12 digits,
and is normally transparent to the end user.
For individuals familiar with using the internet,
they are familiar that every time they activate
their web browser (the software that allows your
computer to connect), there is an address bar
that appears near the top of the screen. This address bar is where you would enter the IP address of the computer or network that you would
like to communicate with. To make this simpler,
these numeric IP addresses are also coded to
allow alpha-numeric names to be masked over
them, so that rather than having to enter an address of 216.27.61.137, you can simply enter in
www.jci.com, as an example. Although the actual process is more detailed and complicated than
this basic explanation, the end result is that most
of the work is being done invisibly.

090.020-CS (JUNE 11)


Page 7

The following write up describes how to set up


the Quantum LX to do this behind the scenes
work, so that it can communicate both at the
Internet level, and at a local Ethernet level.
CABLING
Each Quantum LX Ethernet connection must be
individually cabled (known as a homerun) direct
from a switch or computer. Unlike RS422/485
communications which allowed for cable daisychaining, Ethernet connections do not allow this.
This type of cabling is designed to handle the
100-Mbps speed needed by Ethernet. Both ends
of each cable must have an RJ-45 connector attached. The RJ-45 connector looks similar to the
RJ-11 connector on the end of a telephone cord
but is slightly larger (and not compatible). You
can buy Cat 5 cables in predetermined lengths
with the connectors already attached (for short
runs), or you can buy the cable in rolls, cut it to
length and install the RJ-45 connectors to the
ends (up to 100 meters per each cable run).
Although Frick Controls recommends the use
of shielded, twisted pair Cat 5 cable, if the cable
is not properly constructed and tested, it can actually be more detrimental to the network than
unshielded cable. As long as all of the cables that
are used have been properly constructed AND
tested, either shielded or unshielded are acceptable. This is mostly due to the excellent (electrical) noise immunity that is inherent with Ethernet componentry.
NOTE: Follow standard networking procedures for the interconnections of all components. For individual cable runs in excess of
300 feet (~100 meters), a Switch/Hub must
be used for each additional run.
Cabling Dos and Donts Frick Controls recommends the following guidelines when installing and using CAT 5 Ethernet cable:
Do:

Run all cables in a star (homerun)


configuration.
Keep all individual cable lengths
under 300 feet. If greater distances
are needed, use a switch/hub every
300 feet.
Ensure that the twists of the wire
pairs within the cable are maintained from end to end.
Make gradual bends in the cable.
Keep each bend radius over one
inch.
Keep all cables tie wrapped neatly.
Try to maintain parallel cable runs
where possible.
Keep the cable as far away as possible from EMI sources (motors,

090.020-CS (JUNE 11)


Page 8

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

transformers, solenoids, lighting,


etc.)
Label the ends of each cable, to facility troubleshooting and identifying in the future.
Test each individual cable run with
an approved CAT5 E cable tester. A
TONING alone test is NOT acceptable.
Use rubber grommets anywhere
that the cable enters through a
hole in a metal panel.
ALWAYS obey local, national and
fire building codes.

Dont:

Dont install cable taut, cables


must always have some play or
slack in them.
Dont over-tighten cable ties.
Dont splice a cable. If a break
occurs, or the length is not long
enough (under 300 feet), replace
the entire run with an intact length.
Dont tie cables to electrical conduits.
Dont strip more than one inch
from the end of each cable when
installing end connectors.
Dont sharply bend or kink the cable.
Dont mix 568A and 568B wiring at
the same installation. 568B is the
most common wiring.
Dont use excessive force when
pulling cable.

RJ-45 CONNECTORS
Ethernet network cables require the use of
industry standard RJ-45 plugs as shown below, for the termination of all cables:

hubs, but a switch generally contains more


intelligence than a hub. Unlike hubs, network switches are capable of inspecting
the data packets as they are received, determining the source and destination device
of a packet, and forwarding that packet appropriately. By delivering messages only to
the connected device that it was intended
for, network switches conserve network
bandwidth and offer generally better performance than hubs.
The Switch takes the signal from each computer/Quantum LX and sends it to all of
the other computers/LX panels in your plant
or office. Switches come in several sizes,
noted by the number of ports available -- a
four-port Switch can connect four computers, an eight-port Switch can connect up to
eight computers and so on. So, if you start
with a four-port Switch but eventually add
more panels, you can buy another Switch
and connect it to the one you already have,
increasing the potential number of panels
on your network.

Typical Switch
Note: If you want to connect one computer to
one Quantum LX, you can avoid the switch and
use a crossover Cat 5 cable. With a crossover
cable, you directly connect one Ethernet device
to the other without a Switch. To connect more
than two you need a Switch.
Refer to the following pictorial to construct a
crossover cable:

Typical RJ-45 Connector


THE HUB
A Hub is a common connection point for devices in a network. Hubs are commonly used
to connect segments of a LAN (Local Area
Network). They also contain multiple ports.
When a data packet arrives at one port, it
is copied to the other ports so that all segments of the LAN can see all packets.

1 2 3 4 5 6 7 8

3 6 1 4 5 2 7 8

Left (Not
Crossed)

Right (Crossed)

THE SWITCH
Network Switches look nearly identical to

Both Ends of a crossover-cable

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
CAT-5 Ethernet cable color codes
1 White w/orange stripe
2 Orange w/white stripe
3 White w/green stripe
4 Blue w/white stripe

5 White w/blue stripe


6 Green w/white stripe
7 White w/brown stripe
8 Brown w/white stripe

090.020-CS (JUNE 11)


Page 9

Because of the large number of possible configurations


in an Ethernet network, you most likely will not have any
type of automated installation software. This means that
you will need to manually configure all the options. To
configure these options for the Quantum LX, please refer to the next section in this manual entitled Ethernet
Setup.

ETHERNET COMPONENT RECOMMENDATIONS


Component

Description
Shielded solid 4-pair* (1000 Ft)

Part Number
BOXCAT5E-DSSO
E-PLG-SOLID-SH
Shielded solid 4-pair*
CR45-100S
9504 CS
9504 F
Un-shielded solid 4-pair**
E-PLG-SOLID
345U5-1000BLK
Un-shielded solid 4-pair** (1000 Ft)
0-5EPCS-BK
HT-210C
P-15027
RJ-45 Crimp tool
S2307692
10-RJ1145
RJ-45 For Shielded 4-pair solid wire cable
P-15007
5-554169-3
RJ-45 For Un-shielded 4-pair solid wire cable 1-5E45-010
P-15029
TST-5150
Ethernet Cable Tester Continuity only
TS075A-R2
Complete Cable I/O Qualification Tester
N/A
5 RJ-45 port
SFN-5TX
7 RJ-45 Port and 1 ST Fiber Optic Port
SFN-7TX/FX ST
8 RJ-45 port
SFN-8TX

Cable

Crimp Tool

Connectors

Cable Tester

Switches

Manufacturer
Cablesforless.com
VPI
Cables Direct
Alpha Wire Co.
VPI
Ram Electronics
Computercablestore.com
Cablesforless.com
Stonewall Cable, Inc.
Computers4sure.com
Computercablestore.com
Stonewall Cable, Inc.
Tyco Electronics
Computercablestore.com
Stonewall Cable, Inc.
Cablesforless.com
Black Box
Fluke
Phoenix

* STP = Shielded Twisted Pair


** UTP = Unshielded Twisted Pair

TYPICAL SERIAL WIRING SCENARIO INCLUDING OPTIONAL DBS MOTOR STARTER


After the serial communications wiring has been connected, and jumpers correctly set, the LX software needs to be setup
to match that of the device(s) that it is to communicate with. The following screen is where this information can be found:

External HMI communications

DBS Motor
Communications

DBS Motor
Communications

DBS Motor
Communications

DBS Motor
Communications

DBS Motor
Communications

090.020-CS (JUNE 11)


Page 10

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

ETHERNET SETUP

The following section describes the suggested panel


setup for connecting the Quantum LX panel to an
existing Ethernet connection:

Once all of the cabling has been run and all connections have been made, it is now necessary to setup
the Quantum LX software to recognize and handle
the Ethernet connection.

ACCESSING:

Configuration

Ethernet

DESCRIPTION: This screen is used to allow the user to assign and setup Ethernet and Email communications parameters.

IP DATA
Address Type - The following drop-down menu is
provided:

Fixed (Static) A fixed address is usually


assigned by the network (LAN) administrator, and is normally always the same.
DHCP (Dynamic) Dynamic Host Configuration Protocol permits auto-assignment
of temporary IP addresses for new devices
connecting to the network.

IP Address (Internet Protocol) Four setpoint boxes


are provided here. Every device on an Internet or
Ethernet network must be assigned a unique identifying number, called an IP Address (this is similar in
concept to the Quantum LX panel ID number). The
IP address is how the network identifies each device
that is attached. A typical IP address would look like
this:

216.27.61.137

Gateway Address Four setpoint boxes are provided


here. This is the IP address for the computer or device
onto which your local network is connected to. This

gateway device is how all of the devices attached to


your local network are routed to other gateways and
networks. A router is a Gateway device that routes
packets between different physical networks. A gateway is a network point that acts as an entrance to
another network.
Subnet Mask - A TCP/IP number used to determine
to which TCP/IP subnet a device belongs. Devices in
the same subnet can be communicated with locally
without going through a router When a TCP/IP device
tries to communicate with another device the bits of
the TCP/IP destination address are "ANDed" with the
subnet mask to determine whether the address is
a local address (broadcastable) or must be reached
through a router. A subnet mask of 255.255.255.0 used
by a computer with a TCP/IP address of 10.10.10.1
would include the addresses 10.10.10.0 through
10.10.10.255 in the local network basically telling the
computer to try a router if it's transmitting to any
other IP address. This is all part of the TCP/IP protocol
Web Server Port This is the port, or channel, that
a web server uses to communicate through. Just as
a computer sends data to a printer through a printer
port, a web server sends and receives data through
the Web Server Port. By default, the port number for

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
a Web server is 80.
NAMING DATA
NOTE: The IP Address Type must be set to DHCP (Dynamic) for this section to work.
Host Name Enter a distinct name that you wish to
be able to identify this particular compressor by (for
example; Unit1). The Host Name must be fifteen characters or less in length, use no spaces and use only
upper and lower case letters. It is similar in concept
to the function of the Panel ID, and basically allows
the network router to interpret the actual IP address
of a particular unit as this host name. When using a
web browser within the system network, this name
can be entered as the web location that you wish
to visit (instead of having to type in the IP address).
After modifying a Host Name, you will be required
to cycle power. The network router could take up to
fifteen minutes to recognize the change.
Work Group All of the Quantum LX units within
a network may be grouped into different categories.
These categories could be unit locations, or perhaps categorized by unit function. For instance, if
you wanted to group the units by function, and had
10 units, and three of them were Evaporators (located on the roof), then Evap1 could be the name of
a work group. Another three units may be High Stage
compressors, this work group could be named HighStage1, and the remaining four units could be standard compressors, and they could be named Comp1.
So name each unit by these functional Work Group
names. The Work Group name must be fifteen characters or less in length, and can use numerals and
upper and lower case letters. When using the network neighborhood feature of Windows Explorer,
by looking at your Network Neighborhood, you would
see the name of the Work Group, and within that
work group you would see the individual Host Names
of each unit within that work group. After modifying
a Work Group name, you will be required to cycle
power. The network router could take up to fifteen
minutes to recognize the change.
Server String This is a comment area that can be
used in conjunction with the Host Name. For example, if the Host Name is Booster1, you could set the
Server String to print something like DockBooster, or
some other additional information about the unit. The
Server String has no control function; it is strictly an
informational area.
E-MAIL DATA
The purpose of the E-Mail data feature is to allow the
controller to send a Warning or Shutdown message

090.020-CS (JUNE 11)


Page 11

to defined listing of recipients.


Email Notification On Warning Or Shutdown For the
E-mail notification feature to work, it must be enabled (it is disabled as a default). The following dropdown menu is provided:

Disabled
Enabled

Local Email Address - Use this setpoint box to enter


a valid E-mail address that has been assigned to the
internet account.
Alias Name For Local Email Address Enter here a
custom name to identify more clearly the local Email
address. When a message is sent to all recipients,
this is the name that will appear in the Email FROM
column.
Subject - Enter a custom subject that you would like
to appear when a message failure is sent. When a
message is sent to all recipients, this is the wording
that will appear in the Email SUBJECT column.
SMTP Server Name OR IP Address - SMTP stands
for Simple Mail Transfer Protocol. SMTP servers
handle outgoing email, and accept email from other domains. When you set up an email client, you
must specify an outgoing server (sometimes called
an SMTP server). Often, this server is designated in
the form of smtp.domain.com. But this can vary, so
be sure to check with your email service provider or
LAN administrator to find out their outgoing server.
SMTP Server Port Number - This value is in almost
all cases going to be 25. This should be set by the
network or LAN administrator.
Comma-Delimited List Of Email Recipients - This is
simply the list of the Email addresses that you would
like to have any messages sent to. Separate each email address with a comma.
PROTOCOLS
The purpose of this section is to enable or disable the
Modbus TCP and Ethernet/IP parameters.
Modbus TCP:

Disabled
Enabled

Ethernet/IP:

Disabled
Enabled

090.020-CS (JUNE 11)


Page 12

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 13

SECTION 2
SERIAL COMMUNICATIONS

SERIAL COMMUNICATIONS DESCRIPTION


RS-232 DESCRIPTION
Almost all laptop and desktop computers have
at least one RS-232 serial communications
port available. It was initially developed for the
emerging computer industry in the 1960s. Originally, it was a method of sending data from a
mini or main frame computer, to devices such as
printers, punch card readers, teletypes, magnetic
tape units and modems. In those early days, the
maximum speed at which RS-232 was capable
of transmitting (about 9600 bits per second),
was quite satisfactory, as most of the receiving
devices were mechanical in nature (except for
modems), and barely able to keep up with these
speeds.
RS-232 uses single ended TX (transmit data) and
RX (receive data). This means a common ground
wire is shared between TX and RX, so only 3
wires are needed for a data only serial channel:
TX, RX, and GND.
Disadvantages of single ended signaling is that
it is more susceptible to noise than differential
signaling (RS-422/485), effective cable distances
are shorter (typically about 50 Ft. total, due to
low noise immunity) and data rates are slower.
Additionally, there is the limitation that only two
devices can communicate together (master and
slave).
RS-422/RS-485 DESCRIPTION
When serial communications started moving
into the industrial environment, it was quickly
noted that because of the high electrical noise

potential from electric motors, valves, solenoids,


fluorescent lighting, etc., that the noise immunity
characteristics of RS-232 protocol was grossly
lacking. Additionally, the distances between the
communicating equipment on the factory floor
was much greater than that within the typical office environment. For these reasons, RS-422 and
RS-485 was developed.

RS-422 is a full duplex communications


hardware protocol. This means that it data
can be sent and received simultaneously.
Frick Controls uses a 4-wire system for
RS-422 (two transmit wires and two receive
wires). Advantages of RS-422 over RS-232
is that up to 30 Quantum controllers may
be simultaneously connected using a daisychain wiring scheme (to be explained later),
and that the distances involved can be much
greater (typically up to 2000 ft. for the total cable run), much greater noise immunity
than RS-232.

RS-485 is a half duplex bus. This means that


it can only send data, or receive data at any
given time. It cannot do both at the same
time. Frick Controls uses a 2-wire system
for RS-485 one positive transmit/receive
wire and one negative transmit/receive
wire). Up to 30 Quantum controllers may
be simultaneously connected up to a total
distance of 2000 ft. using a daisy-chain wiring scheme (to be explained later). One advantage to using RS-485 as opposed to RS422 is that only a single twisted pair cable
need to be run to all devices (while RS-422
requires a double twisted pair cable), much
greater noise immunity than RS-232.

090.020-CS (JUNE 11)


Page 14

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SERIAL COMMUNICATIONS SETUP


After the serial communications wiring has been connected, and jumpers correctly set, the LX software needs
to be setup to match that of the device(s) that it is to

ACCESSING:

Configuration

communicate with. The following screen is where this information can be found:

Communication

DESCRIPTION: The purpose of this screen is to allow the user to assign and setup serial communications parameters.
NOTE: This screen has no affect on Ethernet communications.
The following setpoints are provided:
Compressor ID - A number that is used by an external communications application, to converse to individual compressors. On interconnected systems, this
number must be unique. Valid values are from 1 99.
Comm1 - (Setup parameter definitions for Com-1
and Com-2 are identical) Communications related information for the communications ports:
Status - Shows the current communications
status of the port. The possible messages are:

Off - No communications are currently


taking place. NOTE: A delay of 15 seconds or more of inactive communications (time between valid responses)
will cause this message to display.

Active - Valid communications are actively occurring.

Failed - An invalid command was received by the port. This could be due
to a bad checksum value, a wiring issue, or hardware problem at either the

transmitting (host) or receiving (Quantum LX) end.


Baud Rate - The baud rate defines the speed at
which external communications can occur. The
higher the baud rate, the faster the communications. It is best to start out using a lower baud
rate, and increasing the value only after verifying that communications errors do not occur. If
errors start to occur, drop the baud rate back
down. A pull down menu is provided to select
from the following:

1200
2400
4800
9600
19200
38400
57600
115200

Data Bits - Determines the number of bits in a


transmitted data package. A pull down menu is
provided to select from the following:

7
8

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
Stop Bits - A bit(s) which signals the end of a
unit of transmission on a serial line. A pull down
menu is provided to select from the following:

1
2

Parity - In communications, parity checking refers to the use of parity bits to check that data
has been transmitted accurately. The parity bit is
added to every data unit (typically seven or eight
data bits) that are transmitted. The parity bit for
each unit is set so that all bytes have either an
odd number or an even number of set bits. Parity checking is the most basic form of error detection in communications. A pull down menu is
provided to select from the following:

None
Even
Odd

Protocol - A protocol is the special set of rules


that each end of a communications connection
use when they communicate. A pull down menu
is provided to select from the following Frick
recognized protocols:

None
Frick
ModBus ASCII
ModBus RTU
AB DF1 Full Duplex
AB DF1 Half Duplex
DBS Motor Starter
Vyper

Map File - Because the addressing scheme between


the Quantum version 5.0x and earlier software and
the Quantum LX version 6.0x and later software is
not the same, this file was created. The map file is a
conversion utility that can be used to allow a communications application that was previously written
by the user under the Quantum version 5.0x and
earlier to function properly with the Quantum LX by
redirecting the old addresses to the new addresses
(see the section entitled Using the MAP file for additional information). A pull down menu is provided
to select from the following:

No - Do not use map file. The user is either


not going to be using external communications, or they will be writing the communication application based upon Quantum
LX addresses.

Yes - The user has an application that was


previously written for the Quantum version 5.0x or earlier, and they want to utilize
the same code for the Quantum LX.

I/O Comms - A status indicator is provided to show


the current state of the internal communications of
the I/O boards. The possible displayed states are:

Off - Loss of or intermittent communica-

090.020-CS (JUNE 11)


Page 15

tions failures to the internal Quantum LX


I/O boards.

Active - Indicates that normal I/O communications are occurring.

Failed - Loss of communications, a shutdown message will be generated.

Redetect IO Comms - Select this key to detect all


connected Analog and Digital boards. If a board has
been removed, a communication error shutdown will
be issued until this key is selected. Reference the
About screen to view what has been detected.
Two keys are located at the bottom right hand side of the
screen. The following describes there function:
Download MapFile.txt from Quantum LX With
a USB memory stick installed on the LX, pressing this
key will cause the MapFile.txt file to be downloaded
from the Quantum LX into the USB memory.
Upload MapFile.txt to Quantum LX After the
user has modified the MapFile.txt file to suit their
needs, pressing this key will cause the file to be uploaded from the USB memory back into the Quantum LX.
USING THE MAP FILE
The MAP file is simply a text file (map.txt), which can
be downloaded from the Quantum panel. The file
can be used in its original format, which contains a
limited number of addresses, or may be modified by
the user, to incorporate additional addresses.
Downloading The Map File From The Quantum
LX Through a Web Browser:
To download the map file from the Quantum
LX controller, click the Download button. A new
box will appear with a link labeled MapFile.txt.
Right click on the link, and select Save Link Target As from the menu. The web browser will
then present a dialog box allowing the user select a location on their computer for the map file
to be stored. (NOTE: This operation is not intended to be performed from the Operator Interface Panel. Instead, a desktop computer should
be used to access the Evaporator controller via
a web browser).
Downloading the MAP File From the Panel Using a
USB Memory Stick:
Two keys are located at the bottom right side of
the screen. The following describes there function:
Download MapFile.txt from Quantum
LX With a USB memory stick installed
on the LX, pressing this key will cause the
MapFile.txt file to be downloaded from the

090.020-CS (JUNE 11)


Page 16

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

Quantum LX into the USB memory.

memory back into the Quantum LX.

Upload MapFile.txt to Quantum LX


After the user has modified the MapFile.txt
file to suit their needs, pressing this key will
cause the file to be uploaded from the USB

A sample of the original file appears in the following example:

;Quantum to Quantum LX MAP Addresses


;Q,

LX ,

LX Description

0,

1026

;Compressor Motor Start Signal

1,

1027

;Compressor Motor Starter-Feedback/Compressor Interlock

2,

1028

;Oil Pump Start Signal

3,

1029

;Oil Pump Feedback

4,

1003

;Capacity Increase

5,

1002

;Capacity Decrease

6,

1005

;Volume Increase

7,

1004

;Volume Decrease

Quantum Version 5.0


and earlier addresses

Quantum LX
addresses

Quantum LX
Address Description
MapFile.txt Example

USB Memory Stick location

Quantum 4

Q5

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 17

SERIAL COMMUNICATION SETUP TABLE


Use the following form to record all settings:
Compressor ID

_______ (0 - 255)
Com 1

Baud Rate

Data Bits
Stop Bits

Parity

Protocol

Map File

Com 2

Com 3

1200

1200

1200

2400

2400

2400

4800

4800

4800

9600

9600

9600

19200

19200

19200

38400

38400

38400

57600

57600

57600

115200

115200

115200

None

None

None

Even

Even

Even

Odd

Odd

Odd

None

None

None

Frick

Frick

Frick

Modbus ASCII

Modbus ASCII

Modbus ASCII

Modbus RTU

Modbus RTU

Modbus RTU

AB DF1 Full Duplex

AB DF1 Full Duplex

AB DF1 Full Duplex

AB DF1 Half Duplex

AB DF1 Half Duplex

AB DF1 Half Duplex

DBS Motor Starter

DBS Motor Starter

DBS Motor Starter

Vyper

Vyper

Vyper

None

None

None

No

No

No

Yes

Yes

Yes

090.020-CS (JUNE 11)


Page 18

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SERIAL PROTOCOL

5.

DESCRIPTION
The use of serial communication protocols permits data transmission between devices. Protocol determines how contact is established and
how the query (question) and response (answer)
takes place. The information in a message command requires:

6.

The identity of the intended receiver (ID


#)
What the receiver is to do (read or
write to a setpoint, etc.)
Data needed to perform an action (the
value of a setpoint to be changed)
A means of checking for errors (checksum).

When using any of the communications ports,


check what communication protocol has been
selected from the Communications screen. The
baud rate, data bits, stop bits, parity and connection type of all comm. ports, as well as the
panel ID number are also changed from this
screen, and should coincide with the setup of
the other device.
Note: The data communication protocols are continuously being expanded and
improved. Therefore, you should consult
Frick Controls for the exact details on your
particular unit(s) before developing system
software to interface with the panel.

munication port.
Enter the Quantum LX ID. This will be
used to identify commands that are sent to
it.
Wire to the first panel via RS-232 (Quantum 4), RS-422, or RS-485 to the Quantum LX Comm Port.

7.
8.
9.

Send a single command to read data from


this Quantum LX using its ID.
Check if you received a data response at
your device.
Troubleshooting when you dont receive a
data response:

QUANTUM LX COMMUNICATIONS PROTOCOL LIST

The Quantum LX controller has the capability


of communicating to the outside world through
the following software protocols:

Frick
Allen-Bradley DF-1 Full Duplex
Allen-Bradley DF-1 Half Duplex
Modbus ASCII
Modbus RTU
Modbus TCP
Ethernet/IP

CHECKLIST FOR SETTING UP COMMUNICATION


1.
2.
3.
4.

Decide which Quantum protocol you can


communicate with and want to use.
Setup your devices communication port
with the proper parameters and select a
baud rate.
Next, setup the Quantum LX for the desired communication protocol. Select the
protocol from the Communications screen.
Set the baud rate of the Comm Port to coincide with the setup of your devices com-

If you are communicating to more


than one panel, then you will not
be able to use RS-232. You can
however, convert RS-232 to either
RS-422 or RS-485 with an adapter
card. Reference the Converting
an RS-232 Serial Port to RS-422
or RS-485 section for information
about an adapter card.
Refer to the drawing of the Quantum LX Main Board in this manual to identify wiring and jumper
locations for the Comm Ports.
Refer to the Main Board Communications section in this manual for
the correct jumpering of RS-232
(Quantum 4), RS-422, or RS-485.

Check to see if the status of the


Comm Port on the Communications screen is showing ACTIVE or
OFF.
ACTIVE is shown only when the
Quantum LX understands it is
receiving a properly composed
message.
Check that the RX I/O communication activity lamp on the Quantum LX Main Processor Board is
blinking as it receives the instruction from your device.
A steady lit RX LED or one that
isnt lighting, are signs of improper
wiring.
If the RX LED is properly blinking,
then check if the TX LED is blinking
in response.
If the TX is not blinking then check
the communication protocol setup
at the panel, the panels ID and the
Comm Port baud rate setting.
If the TX is blinking, then check
that the Comm Port communication jumpers are correct.

Note: A useful tool for troubleshooting is Windows HyperTerminal. Refer to the HyperTerminal
Setup section in this manual for more information.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
If you properly receive data and need to communicate to more than one panel, then setup
and wire to another panel. Reference the wiring diagram drawings in the back of this manual.
Send a single command to read data from this
Quantum LX using its ID and troubleshoot as
above, if necessary. To prevent noise feedback
which is possible when communicating over a
long distance, only the last panel should have the
termination jumpers installed.

FRICK PROTOCOL

The following is a complete list of available Frick Protocol # commands:


COMMAND CODE and DESCRIPTION
I

= Returns compressor status (I)nformation

= Compressor sta(R)t control

= Compressor (S)top control

= Return full load (A)mps information

= Slide (V)alve/Slide stop control

MC

= Change (M)ode of (C)ompressor

MV = Change (M)ode of Slide (V)alve

DESCRIPTION
All commands for Frick protocols must
be in ASCII to be recognized (see the Conversion Chart For Decimal / Hexadecimal
/ ASCII, located later in this manual). The
commands can be in upper or lower case
letters. A compressor with an ID code of
[00] is considered disabled. ID codes from
[01] through [99] are valid and recognized
by the Quantum.
FRICK # PROTOCOL SPECIFICATIONS
Frick # protocol consists of commands that
are available for most other existing models of Frick compressor control panels. The
Frick # protocol does not utilize a checksum.
It is better to use Frick Quantum ($) protocol when only communicating to Quantum 4A or Quantum LX panels.
When there is more than one panel, a Quantum LX can be wired from its communications ports to another panels ports, or can
be wired to Port 1 of a RWB, RDB, RXB or
RXF Micro Plus panel.
Frick RWB, RDB, RXB, or RXF Panel Frick #
Communications Port #1 RS-422 Pinout
9
8
5
4

090.020-CS (JUNE 11)


Page 19

- TX (Transmit)
+ TX (Transmit)
- RX (Receive)
+ RX (Receive)

= Return (P)ressures information

= Return (T)emperatures information

= (Q)uery setpoints data

= Enter (C)hange setpoints mode

= Return (F)ailures

KF

= (K)Clear (F)ailures

KR

= (K)Clear remaining (R)ecycle delay time

All data is returned as integer values. If decimal positions


are assumed, then divide the data by the proper multiple
of 10 to get the actual value.
Temperature data, except for Suction Temperature, is
returned in the current temperature units as 3 characters with no decimal position (i.e. 032 would represent
32 degrees Fahrenheit if the panel temperature units are
in Fahrenheit, or it would represent 32 degrees Celsius, if
the panel temperature units are in Celsius). Suction Temperature is returned as 4 characters with a + or as the
leading character (i.e. 010 would represent 10 degree).
Pressure data is usually returned in the current pressure
units. However, the Filter differential reading is always returned in PSIA. When in PSIG or in PSIA, the pressure
data is returned as 3 characters with no decimal position.
However; in order to show the full transducer range, the
#IDPS command returns 4 characters with one decimal
position assumed. The #IDI, and #IDPA commands return
3 characters that assume one decimal position; therefore,
99.9 is the highest value that can be returned. When in
PSIG, suction pressure is returned in PSIA. When in Bar
and BarA, the pressure data is returned as 4 characters
with two decimal positions assumed. When in KpaA, the
pressure data is returned as 4 characters with no decimal
position.

090.020-CS (JUNE 11)


Page 20

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

The following is a detailed description of each command:


RETURN COMPRESSOR STATUS INFO:

#IDI

Command structure:
Command

COMPRESSOR START CONTROL:

Description

Start of command sequence

ID

Compressor (ID) code (01, 14, etc.)

1, 2, 3

Return Status (I)nformation command

7
8, 9, 10

Description of returned data

(R)emote

(A)uto

M =

(M)anual

(R)unning

(O)ff

(Slide Valve)

(S)lide Valve too high

(P)ermissive Start not energized

d(I)fferential Pressure too high

s(T)opping
Au(X) not energized

(U)nable to start

(R)emote

M =

(M)anual

(A)uto

(C)utout (Shutdown)

(A)larm

(N)ormal

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

Sta(R)t compressor command.

ID

(ID) code repeated for verification

Returned answer:

Description

Character
Position

Command

NOTE: The compressor must be in the remote Start


Mode for this command to be executed.

Slide Valve position.


R

#IDRID

Command structure:

Returned Answer, ie: 090RRRN340


Character
Position

Note: The following control commands are for remote


control of a compressor. A compressor should be in both
remote compressor mode and remote Slide Valve or capacity mode for remote control.

Description of returned data


(A)cknowledge

2, 3

(ID) code verified


CR, LF (Carriage return, line feed)

COMPRESSOR STOP CONTROL:

#IDSID

Command structure:
Command
(Compressor
mode)

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

(S)top compressor command.

ID

(ID) code repeated for verification

NOTE: The compressor must be in the remote


Start mode for this command to be executed.

Suction value in PSIA.


CR, LF (Carriage Return, Line Feed)

Description

Returned answer:
Character
Position
1
2, 3

Description of returned data


(A)cknowledge
(ID) code verified
CR, LF (Carriage return, line feed)

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
RETURN FULL LOAD AMPS COMMAND:

#IDA

RETURN SLIDE STOP POSITION COMMAND:

#IDVP

Command structure:

Command structure:
Command

090.020-CS (JUNE 11)


Page 21

Command

Description

Description

Start command sequence

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

ID

Compressor (ID) code (01, 14, etc.)

Return Full Load (A)mps command

Slide (V)alve / Slide Stop command

Return Slide Stop (P)osition value

Returned Answer:
When using the A command, the returned Full Load
Amps will be:
XXX = 3 characters followed by a CR, LF.

Returned Answer:
Character
Position

Description of returned data

1, 2
SLIDE VALVE CONTROL COMMANDS:

CR, LF (Carriage return, line feed)

#IDVS
#IDVUXX

Command structure:
Command

Slide Stop position, i.e. 25 = 2.5

#IDVLXX

Description

CHANGE COMPRESSOR MODE


COMMAND:

#IDMCmID

Command structure:

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

Slide (V)alve / Slide Stop command

Start command sequence

(L)oad Slide Valve command

ID

Compressor (ID) code (01, 14, etc.)

(U)nload Slide Valve command

MC

Change (M)ode of (C)ompressor

XX = 00
XX = 01 to
15
S

Turns selected output off


Turns selected output on for XX seconds
Return (S)lide Valve position value

If the command was #01VL00, then the load Slide Valve


output on compressor #1 would be turned off. If the
command was #01VL05, then the load Slide Valve output on compressor #1 would be turned on for 5 seconds,
and would then automatically turn off. NOTE: the Slide
Valve must be in the remote mode for this command
to be executed. Time is not accrued, each command
restarts timer.
Returned Answer (for L or U commands):
Character
Position
1
2, 3

Description of returned data


(A)cknowledge
(ID) code verified
(Carriage return, line feed.)

Returned Answer (for S command):


Character
Position
1, 2, 3

Command

Description of returned data


Slide Valve position.
CR, LF (Carriage return, line feed)

Description

(O)ff

(A)uto

(R)emote

ID

(ID) code repeated for verification

Returned Answer:
Character
Position
1
2, 3

Description
(A)cknowledge
(ID) code verified
(Carriage return, line feed)

090.020-CS (JUNE 11)


Page 22

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

CHANGE SLIDE VALVE MODE


COMMAND:

#IDMVmID

Command

Description

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

MV

(M)ode of Compressor Slide (V)alve

(O)ff

(A)uto

(R)emote

ID

(ID) code repeated for verification

Returned Answer:
Description

2, 3

Start command sequence


Compressor (ID) code (01, 14, etc.)

Return (T)emperature command


=

Return (S)uction Temperature

Return (D)ischarge Temperature

Return (O)il Temperature

Return Se(P)arator Temperature

Return (A)ll temps as a string of data

Returns the Suction Temperature

(A)cknowledge

#01TD

Returns the Discharge Temperature

(ID) code verified

#01TO

Returns the Oil Temperature

(Carriage return, line feed)

#01TP

Returns the Separator Temperature

#01TA

Returns All Temperatures

#IDPX

Command structure:
Description

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

Return (P)ressures command


=

#
ID

#01TS

RETURN PRESSURES COMMAND:

Command

Description

Command Examples: (Compressor #01 is used here)

Character
Position
1

#IDTX

Command structure:

Command structure:
Command

RETURN TEMPERATURES COMMAND:

Return (S)uction Pressure (PSIA)

Return (D)ischarge Pressure (g/hg)

Return (O)il Pressure (g)

Return (F)ilter differential Pressure

Return (A)ll pressures as a string of


data

Command Examples: (Compressor #01 is used here)


#01PS

Returns the Suction Pressure

#01PD

Returns the Discharge Pressure

#01PO

Returns the Oil Pressure

#01PF

Returns the Filter Differential Pressure

#01PA

Returns All pressures

Note: Dont send CR or LF


Returned Answer:
If using the S command the returned pressure will be:
XXXX = 4 characters followed by a CR, LF.
If using the D, O or F commands, the returned pressure
will be: XXX = 3 characters followed by a CR, LF.
If using the A command, the returned data would be:
XXXXXXXXXXXX = 12 characters followed by a CR, LF.

Note: Dont send CR or LF


Returned Answer:
If using the S command the returned temp. will be:
+/-XXX = The first character will be a + or -, followed
by 3 characters and ending with a CR, LF.
If using the D, O or P commands, the returned temp.
will be:
XXX = 3 characters followed by a CR, LF.
If using the A command, the returned data would be:
XXXXXXXXXXXX = 12 characters followed by a CR, LF.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
QUERY SETPOINTS DATA:

#IDQ1

Command structure:
Command

Description

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

Q1

(Q)uery Setpoints command

Returned Answer:

QUERY SETPOINTS DATA:

#IDQ2

Command structure:
Command

Description

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

Q2

(Q)uery Setpoints command

Returned Answer:

Character
Position

#
Byte(s)

Always 0

2, 3, 4, 5

Capacity Control Setpoint, 3


chars followed by g or h

14, 15

Prop band

16, 17

Dead band

18, 19

Cycle time

20, 21, 22, 23

Future

24, 25, 26, 27

Future

28, 29, 30, 31

Future

32, 33

Future

34, 35

Future

36, 37

Future

High Discharge Pressure


Shutdown

42, 43, 44, 45

High Discharge Pressure


Warning

46

ID (tenths position byte)

47

ID (ones position byte)

48

ID Checksum of all data (pos.


1 to 47)

49

CR code 13

50

LF code 10

51

0 null terminator char.

38, 39, 40, 41

090.020-CS (JUNE 11)


Page 23

Setpoint (Name/Comment)

Character
Position

# Byte(s)

Setpoint (Name/Comment)

1, 2, 3

Future

4, 5, 6

Future

7, 8, 9

MLC amps stop load

10, 11, 12

MLC amps force unload

13, 14, 15

CT factor

16, 17

Recycle delay (setpoint,


not time left)

18

Aux 1

0=
Warning
1=
Shutdown

19

Aux 1

0 = NO
1 = NC

20

Aux 2

0=
Warning
1=
Shutdown

21

Aux 2

0 = NO
1 = NC

22

Future

23, 24

Future

25

Future

26

Future

27, 28

Future

29

Future

30

ID (tenths position byte)

31

ID (ones position byte)

32

ID Checksum of all data


(pos. 1 to 47)

33

CR code 13

34

LF code 10

35

0 null terminator char.

090.020-CS (JUNE 11)


Page 24

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUERY SETPOINTS DATA:

#IDQ3

#IDC

Command structure:

Command structure:
Command

CHANGE SETPOINTS COMMAND:

Command

Description

Description

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

ID

Compressor (ID) code (01, 14, etc.)

Q3

(Q)uery Setpoints command

Returned Answer:
Character
Position

#
Byte(s)

Setpoint (Name/Comment)

1, 2, 3, 4

Spaces

5, 6, 7, 8

Future

Setback
active

10, 11, 12, 13

Auto. Cycling compressor Start

14, 15, 16, 17

Auto. Cycling compressor Stop

1 = Yes
0 = No

Start command sequence

(C)hange setpoint command

xx

Which setpoint

xxx

New value

g or h for gauge or inches

The following is the complete list of setpoints that may


be changed while in the change setpoints command:
01xxxy

Capacity Control Setpoint


(y deleted for KpaA & BarA ver.)

02xxxy

Change Low Suction Shutdown Setpoint


(y deleted for KpaA & BarA ver.)

03xxxy

Capacity Low Suction Alarm Setpoint


(y deleted for KpaA & BarA ver.)

04xxx

Change High Press. Shutdown Setpoint


(xxxx is used for KpaA & BarA ver.)

05xxx

Change High Press. Alarm Setpoint


(xxxx is used for KpaA & BarA ver.)

18, 19

Future

20, 21

Future

22, 23

Autocycle minimum Slide Valve

24

Autocycle
active

25, 26, 27, 28

Future

29, 30, 31, 32

Future

06xxx

Change MLC Stop Load Setpoint

33, 34

Future

07xxx

Change MLC Force Unload Setpoint

35, 36

Future

08xx

Change Recycle Delay Setpoint

37, 38

Future

09xxx

Change CTF Setpoint


Proportional Band

1 = Yes
0 = No

39

Future

10xx

40

ID (tenths position byte)

11xx

Dead Band

41

ID (ones position byte)

12xx

Cycle Time

42

ID Checksum of data (positons


1-47)

43

CR code 13

44

LF code 10

45

0 null terminator char.

01

Compressor ID code

Returned Answer:
Axxxx

The new setpoint which was sent


followed by a carriage return, line
feed. BAD followed by the ID, CR, LF if
unsuccessful.

Returned Example 1: If #01C01300g01 is sent:


The capacity control setpoint would be changed to
30.0g and the returned answer is A300g followed by a
CR, LF.
Returned Example 2: If #01C0711001 is sent:
The MLC force unload setpoint would be changed to
110% and the returned answer is A110 followed by a
CR, LF.
Returned Example 3: If #01C0520002 is sent:
The returned answer is BAD followed by the ID number and a CR, LF.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
RETURN FAILURE COMMAND:

#IDF

CLEAR FAILURE COMMAND:

#IDKFID

Command structure:

Command structure:
Command

090.020-CS (JUNE 11)


Page 25

Command

Description

Description

Start command sequence

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

ID

Compressor (ID) code (01, 14, etc.)

Return Discrete (F)ailures List

KF

(K)Clear (F)ailures

ID

(ID) code repeated for verification

Returned Answer:
Character
Alarm
Position
Description
1
2
3
4
5

High Discharge Pressure


Shutdown
High Discharge Pressure
Warning
Low Suction Pressure
Shutdown
Low Suction Pressure
Warning
Low Oil Pressure Shutdown and/or Differential
Oil Pressure Shutdown

Low Oil Pressure Warning

High Oil Temp. Shutdown

High Oil Temp. Warning

Low Oil Temp. Shutdown

10

Low Oil Temp. Warning

11
12
13
14

High Discharge Temp.


Shutdown
High Discharge Temp.
Warning
Compressor Aux. FailShutdown
Pump Aux. Fail- Shutdown

15

Oil Level Shutdown

16

Unused - 0

17

High Oil Filter Pressure


Warning

18

Unused - 0

19

Aux. 1 Alarm/Shutdown

20

Aux. 2 Alarm/Shutdown

21

Low Motor Current Shutdown

22

Sensor Fault

23

Unused - 0

24

Unused - 0

Returned Answer:
0 = Safe
1 = Shutdown
0 = Safe
1 = Warning
0 = Safe
1 = Shutdown
0 = Safe
1 = Warning

Character
Position
1
2, 3

Description
(A)cknowledge
(ID) code verified
(Carriage return, line feed)

0 = Safe
1 = Shutdown

CLEAR ANTIRECYCLE COMMAND:

0 = Safe
1 = Warning
0 = Safe
1 = Shutdown
0 = Safe
1 = Warning
0 = Safe
1 = Shutdown
0 = Safe
1 = Warning
0 = Safe
1 = Shutdown
0 = Safe
1 = Warning
0 = Safe
1 = Shutdown
0 = Safe
1 = Shutdown
0 = Safe
1 = Shutdown

Command structure:

0 = Safe
1 = Warning
0 = Safe
1 = Shutdown
0 = Safe
1 = Shutdown
0 = Safe
1 = Shutdown
0 = Safe
1 = Warning

NOTE: Returns a 24 char data string followed by ID, CR, LF.

Command

#IDKRID

Description

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

KR

(K)Clear (R)ecycle Delay

ID

(ID) code repeated for verification

Returned Answer:
Character
Position
1
2, 3

Description
(A)cknowledge
(ID) code verified
(Carriage return, line feed)

090.020-CS (JUNE 11)


Page 26

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUANTUM $ PROTOCOL SPECIFICATIONS


Quantum ($) protocol commands are used by both
the Quantum and the Quantum LX. This protocol has been modified slightly for the LX, in that the
D command has been eliminated, and the addressing structure has changed. Any previously configured
Quantum LX protocol applications that had been
written for Quantum panels, will still work for the
LX, by using the Map File on the Communications
Screen.
Unless otherwise shown, 9 characters are returned
from the Quantum for a data value. The data value
includes two decimal fields and the first character
position is either; - if the value is negative, or it is
+ if the value is positive. For example, if the datas
value is 25.5; then the value +00002550 is sent. All
temperatures are in degree C and all pressures are
in PSIA. A mode such as Slide Valve mode is returned as an integer value that represents the mode
that it is in. For example, a +00000000 is sent if it
is in manual, or a +00000100 is sent if it is in automatic, or a +00000200 is sent if it is in remote.
The value zero +00000000 is used to represent an
OFF status and a DISABLED option. The value one
+00000100, which is received as a 1, is used to represent an ON status and an ENABLED option. Setpoints are only changed if the value sent is within the
acceptable range. Reference the Frick Quantum
Control Panel Maintenance publication S90.020-M for
the setpoints default settings and ranges. The checksum is the 2 byte hexadecimal sum of each character
within the command or returned answer excluding
the command type identifier, $. If the commands
checksum is replaced with ??, the Quantum returns
a response without using checksum error checking
on the received command (refer to the Data Packet
section for more information). If the Quantum detects a checksum error, a N (Not Acknowledged), the
Compressor ID code, 02, Carriage return, and Linefeed are returned.
This document will demonstrate how to communicate to the Quantum panel using the tables that
appear on the following pages.
Data Packet
If you were interested in viewing the information that
is contained in any of the accessible Quantum addresses, you would want to refer to the table entitled
RETURN DATA VALUE FROM TABLE $IDT1 table later
in this section.
The quickest way to demonstrate this protocol is
through Hyperterminal (see the section entitled Hyperterminal later in this manual). After setting up Hyperterminal and ensuring that all wiring and jumper
configurations are correct, type a $ symbol. This is
the character that will alert all of the Quantum
panels on the communications line that data is on its
way. Following the $ symbol, type the ID code of the
Quantum that you wish to query (for instance 01 for

the first Quantum). After the ID number, type a T1.


The protocol code in the Quantum recognizes this
portion of the data packet as a request for the data
from a memory location (address).
Up to now you have typed the following information:
$01T1. Now you to need specify the address(s) that
you wish to query. Up to sixteen addresses may simultaneously be requested. The format for this entry
must be in the form of four digits, so if you want
to query the Frick address for Suction Pressure (address 2002), simply enter the value 2002. Your command line should now look like this: $01T12002. If
you would like to view additional addresses, simply
continue to append the address numbers to this command (up to sixteen total). For this example, we will
only use the one address (2002 for Suction Pressure).
The next thing that must be done is to enter a checksum value. You may elect to type in a ?? as a wildcard if you do not have the time to figure the correct
checksum, however, the information that is returned
may or may not always be reliable. The checksum will
ensure reliability.
To arrive at the checksum value for the command you
have just typed, you will need to convert each ASCII
digit into hexadecimal (do not include the $ symbol).
For this example, you will need to take the first digit
0, and referring to the Conversion Chart at the end
of this section, look down the ASCII column until you
find 0. You will notice that the Hexadecimal equivalent for ASCII 0 is 30 hex. Repeat the process of
looking up each digit in the ASCII column, and finding
its equivalent in the Hexadecimal column, and write
each value down. When all eight (minimum) digits
(01T12002) have been converted to hexadecimal, you
will need to add the eight values together. Remember, the values are in hexadecimal format, not decimal. If you are not familiar with hexadecimal math,
you may wish to utilize the calculator that comes with
Microsoft Windows. Look at the following chart:
ASCII Value of Data
Packet
0
1
T
1
2
0
0
2
Hex Total

Hexadecimal
Equivalent
30
31
54
31
32
30
30
32
1AA

The answer that is arrived at from the previous chart


is 1A8.
NOTE: For any calculation that results in an answer of more than two digits, use only the right
most two digits, and disregard all digits to the
left.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
This will become the checksum for the data packet,
and is appended to the end of the data that has so far
been typed in.
The result should look like this:
$01T12002A8
Press the [Enter] key. You should see an immediate
response. The format of this response should resemble something (but not necessarily exactly) like:
A01+00006166B6
Referring to the RETURN DATA VALUE FROM TABLE
$IDT1 table on the next page, we find that the first
line of the response, A01, indicates that an Acknowledgement (A) was received from device 01 (01). This
is followed by +00006166 (Suction Pressure). The
plus (+) symbol indicates a positive value, followed
by 00006166. Since there are two decimal positions
assumed, 0006166 equals 61.66 PSIA. Using the +/symbols as a delimiter in the above example, each
section of 8 digits can be interpreted as the actual
value being returned from each of the address queries. The B6 value at the very end of the response
is the checksum value that the Quantum returned,
not actual data.
The following is a complete list of available $ command types:
COMMAND CODE and DESCRIPTION

090.020-CS (JUNE 11)


Page 27

The following is a detailed description of each command:


CLEAR ALARMS COMMAND:

$IDCA

Command structure:
Command

Description

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

CA

(C)lear (A)larms

CS

Checksum

CR

Carriage Return

Returned Answer:
Character
Position
1
2, 3

Description of returned data


(A)cknowledge
(ID) code verified
Carriage Return, Line Feed

SLIDE VALVE CONTROL COMMANDS:

$IDCLXX

Command structure:
Command

Description

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

Slide Valve/Slide Stop (C)ommand

CA

Clear Alarms

(L)oad Slide Valve command

CL

Compressor load

(U)nload Slide Valve Command

CP

Compressor stop

CS

Change a setpoint in the Table

CT

Compressor Start

CU

Compressor unload

CS

Checksum

CR

Carriage Return

D1

Operating Status Display Page 1

D2

Operating Status Display Page 2

D3

Operating Status Display Page 3

D4

Operating Status Display Page 4

F1

Warnings/Shutdowns Annunciation Page 1

F2

Warnings/Shutdowns Annunciation Page 2

F3

Warnings/Shutdowns Annunciation Page 3

MA

Compressor mode Autocycle

MM

Compressor mode Manual

MR

Compressor mode Remote

S2

Compressor sequence activate

S3

Compressor sequence de-activate

T1

Read a value from the Table

VA

Slide Valve mode Automatic

VR

Slide Valve mode Remote

XX = 00
XX=01 to 15

Turns selected output off.


Turns selected output on for XX
seconds.

If the command is $01CL00, then the load Slide Valve


output on compressor #1 would be turned off. Time
is not accrued, each command restarts timer. NOTE:
the Slide Valve must be in the remote mode for this
command to be executed.
Returned Answer (for L or U commands):
Character
Position
1
2, 3

Description of returned data


(A)cknowledge
(ID) code verified
Carriage Return, Line Feed

090.020-CS (JUNE 11)


Page 28

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

COMPRESSOR STOP COMMAND:

$IDCP

Command structure:
Command

COMPRESSOR START COMMAND:

$IDCT

Command structure:

Description

Start command sequence

Command

Description

Start command sequence

ID

Compressor (ID) code (01, 14, etc.)

ID

Compressor (ID) code (01, 14, etc.)

CP

(C)ompressor (S)top

CT

(C)ompressor S(T)art

CS

Checksum

CS

Checksum

CR

Carriage Return

CR

Carriage Return

Returned Answer:

Returned Answer:

Character
Position

Description of returned data

(A)cknowledge

2, 3

Character
Position
1

(ID) code verified

2, 3

Carriage Return, Line Feed


CHANGE SETPOINT COMMAND:

(A)cknowledge
(ID) code verified
Carriage Return, Line Feed

$IDCS

Command structure:
Command

Description of returned data

Description

SLIDE VALVE CONTROL COMMANDS:

$IDCUXX

Command structure:
Command

Description

Start of command sequence

Start command sequence

ID

Compressor (ID) code

ID

Compressor (ID) code (01, 14, etc.)

CS

(C)hange (S)etpoint in Table address

Slide Valve/Slide Stop (C)ommand

Fricks Table address of the setpoint

(U)nload Slide Valve command

0000
+/-

Polarity indicator (for the new setpoint)

XX = 00

0000 0000

Value of the new setpoint. Decimal point


assumed to two places (0000 00.00)

XX=01 to 15

Turns selected output off


Turns selected output on for XX
seconds

CS

Checksum

CS

Checksum

CR

Carriage Return

CR

Carriage Return

Returned Answer:
Character
Position
1
2, 3

Description of returned data


(A)cknowledge
(ID) code verified

If the command is $01CU05, then the load Slide Valve


output on compressor #1 would be turned on for 5 seconds, and would then automatically turn off. Time is not
accrued, each command restarts timer. NOTE: the Slide
Valve must be in the remote mode for this command
to be executed.

Carriage Return, Line Feed


RETURNED ANSWER (for L or U commands): A01
Character
Position
1
2, 3

Description of returned data


(A)cknowledge
(ID) code verified
Carriage Return, Line Feed

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
RETURN OPERATING STATUS
Page 1 Data:

$IDD1

Command structure:

090.020-CS (JUNE 11)


Page 29

RETURN OPERATING STATUS


Page 2 Data:
Command structure:

Command

Description

Command

Description

Start of command sequence.

Start of command sequence.

ID

Compressor (ID) code (01, 14, etc.)

ID

Compressor (ID) code (01, 14, etc.)

D1

Operating Status (D)ata


Page (1) command.

D2

Operating Status (D)ata


Page (2) command.

CS

Checksum

CS

Checksum

CR

Carriage Return

CR

Carriage Return

RETURNED ANSWER,
Character
Position
1

$IDD2

Description of returned data


(A)cknowledge

RETURNED ANSWER,
Character
Position
1

Description of returned data


(A)cknowledge

2, 3

(ID) code verified

2, 3

(ID) code verified

4-12

Suction Pressure

4-12

Alarm Status

13-21

Suction Temperature

13-21

Shutdown Status

22-30

Discharge Pressure

22-30

Running Status

31-39

Discharge Temperature

31-39

Slide Valve Load

40-49

Oil Pressure

40-49

Slide Valve Unload

49-57

Oil Temperature

49-57

Slide Stop Increase

58-66

Filter Differential

58-66

Slide Stop Decrease

67-75

Motor Current

67-75

Stop Load/Force Unload Code

76-84

FLA%

76-84

Separator Temperature

85-93

Kilowatts

85-93

Balance Piston Pressure

94-102

Slide Valve

94-102

Process Variable

103-111

Slide Stop

103-111

Compressor Mode

112-120

Process Temperature

121, 122

Checksum, Carriage Return, Line Feed if


successful

112, 113

Checksum, Carriage Return, Line Feed if


successful

090.020-CS (JUNE 11)


Page 30

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

RETURN OPERATING STATUS


Page 3 Data:

$IDD3

RETURN Alarms & Shutdowns


Page 1 Data:

$IDF1

Command structure:
Command Description

Command structure:

Start of command sequence

ID

Compressor (ID) code (01, 14, etc.)

Start of command sequence

D3

Operating Status (D)ata


Page (3) command

ID

Compressor (ID) code (01, 14, etc.)

CS

Checksum

F1

(F)ailure Annunciation command Page (1)

CR

Carriage Return

CS

Checksum

CR

Carriage Return

Command Description

RETURNED ANSWER,
Character
Position
1

Description of returned data

RETURNED ANSWER,

(A)cknowledge

Character
Position

2, 3

(ID) code

4-12

Communication Port 1 Code

13-21

Communication Port 2 Code

22-30

I/O Communication Port Code

31-39

Capacity Control Mode

40-48

Process Control

49-57

Oil Pump Mode

23

58-66

Oil Pump Code

24-26

Description of returned data


(A)cknowledge

2, 3

(ID) code

4-6

Message Code 1

7-14

Date 1 as mm/dd/yy

15-22

Time 1 as hh:mm:ss
Space
Message Code 2

67-75

Oil Heater Code

27-34

Date 2 as mm/dd/yy

76-84

Process Setpoint

35-42

Time 2 as hh:mm:ss

85-93

Slide Valve Mode

43

94-102

Slide Stop Mode

44-46

Message Code 3

103-111

Runtime Hours
Checksum, Carriage Return, Line Feed if
successful

47-54

Date 3 as mm/dd/yy

55-62

Time 3 as hh:mm:ss

112, 113

RETURN OPERATING STATUS


Page 4 Data:

$IDD4

63

Space

64-66

Message Code 4

67-74

Date 4 as mm/dd/yy

75-82

Command structure:

Space

Time 4 as hh:mm:ss

Command

Description

83

$
ID

Start of command sequence


Compressor (ID) code (01, 14, etc.)
Operating Status (D)ata
Page (4) command

84-86

Message Code 5

87-94

Date 5 as mm/dd/yy

95-102

Time 5 as hh:mm:ss

CS

Checksum

CR

Carriage Return

RETURNED ANSWER,
Character
Position
1

Description of returned data


(A)cknowledge

2, 3

(ID) code.

4-12

Date as 00/00/00

13-22

Time as hh:mm:ss

23-29

Remaining Recycle time as mm:ss

30, 31

Checksum, Carriage Return, Line


Feed if successful

103

Space

Space

104-106

Message Code 6

107-114

Date 6 as mm/dd/yy

115-122

Time 6 as hh:mm:ss

123
124-125

Space
Checksum, Carriage Return, Line Feed if
successful

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
RETURN Alarms & Shutdowns
Page 2 Data:

$IDF2

Command structure:
Command Description
$

Start of command sequence

ID

Compressor (ID) code (01, 14, etc.)

F2

(F)ailure Annunciation command Page (2)

CS

Checksum

CR

Carriage Return

RETURNED ANSWER,
Character
Position
1

Description of returned data


(A)cknowledge

2, 3

(ID) code.

4-6

Message Code 7

7-14

Date 7 as mm/dd/yy

15-22

Time 7 as hh:mm:ss

23

Space

24-26

Message Code 8

27-34

Date 8 as mm/dd/yy

35-42

Time 8 as hh:mm:ss

43

Space

44-46

Message Code 9

47-54

Date 9 as mm/dd/yy

55-62

Time 9 as hh:mm:ss

63

Space

64-66

Message Code 10

67-74

Date 10 as mm/dd/yy

75-82

Time 10 as hh:mm:ss

83

Space

84-86

Message Code 11

87-94

Date 11 as mm/dd/yy

95-102

Time 11 as hh:mm:ss

103

Space

104-106

Message Code 12

107-114

Date 12 as mm/dd/yy

115-122

Time 12 as hh:mm:ss

123
124, 125

Space
Checksum, Carriage Return, Line Feed if
successful

090.020-CS (JUNE 11)


Page 31

RETURN Alarms & Shutdowns


Page 3 Data:

$IDF3

Command structure:
Command

Description

Start of command sequence.

ID

Compressor (ID) code (01, 14, etc.)

F3

(F)ailure Annunciation command Page (3)

CS

Checksum

CR

Carriage Return

RETURNED ANSWER,
Character
Position
1

Description of returned data


(A)cknowledge

2, 3

(ID) code.

4-6

Message Code 13

7-14

Date 13 as mm/dd/yy

15-22

Time 13 as hh:mm:ss

23

Space

24-26

Message Code 14

27-34

Date 14 as mm/dd/yy

35-42

Time 14 as hh:mm:ss

43

Space

44-46

Message Code 15

47-54

Date 15 as mm/dd/yy

55-62

Time 15 as hh:mm:ss

63

Space

64-66

Message Code 16

67-74

Date 16 as mm/dd/yy

75-82

Time 16 as hh:mm:ss

83

Space

84-86

Message Code 17

87-94

Date 17 as mm/dd/yy

95-102

Time 17 as hh:mm:ss

103

Space

104-106

Message Code 18

107-114

Date 18 as mm/dd/yy

115-122

Time 18 as hh:mm:ss

123
124, 125

Space
Checksum, Carriage Return, Line Feed if
successful

090.020-CS (JUNE 11)


Page 32

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

RETURN Data Value From Table:

$IDT1

Command structure:
Command

Description

Start of command sequence.

ID

Compressor (ID) code (01, 14, etc.)

T1

Return the value of a Table address.

0000
0000
0000
0000
0000
0000
0000
0000

Frick Address (s) of data value in Table.


Up to 16 different addresses can be re0000 quested.
0000
0000 Example # 1: if requesting Suction Tem0000 perature only, command would be (to
0000 compressor ID of 1); $01T10128CSCR.
0000
0000 Example # 2: If requesting address 128
0000 through 136, the command would be:
$01T10128012901300131013201330134
01350136CSCR.

NOTE: The following commands are for remote control


of a compressor. A compressor should be in both remote
compressor mode and remote Slide Valve or capacity
mode for remote control.
COMPRESSOR MODE
AUTOCYCLE COMMAND:
Command structure:
Command Description
$

Start of command sequence.

ID

Compressor (ID) code (01, 14, etc.)

MA

(M)ode (A)utocylce

CS

Checksum

CR

Carriage Return

RETURNED ANSWER,
Character
Description of returned data
Position
1

CS

Checksum

CR

Carriage Return

RETURNED ANSWER,
Character
Position
1
2, 3

Description of returned data

4-End

2, 3

(A)cknowledge
(ID) code.
Carriage Return, Line Feed if successful

COMPRESSOR MODE
MANUAL COMMAND:

(A)cknowledge

Command structure:

(ID) code.

Command Description

Value(s) of requested data.


CS (Checksum followed by CR, LF) if successful.
The response to example # 1 above would
look like: A01+000018731F, the plus symbol (+) indicates that the data value returned is positive.
The response to example # 2 above would
look like:
A01+00001873+00004901+00002949+0
0005652-0027249+00008211+00013354
+00000656+0000288109

$IDMA

Start of command sequence.

ID

Compressor (ID) code (01, 14, etc.)

MM

(M)annual (M)ode

CS

Checksum

CR

Carriage Return

$IDMM

RETURNED ANSWER,
Character
Position
1
2, 3

Description of returned data

(A)cknowledge
(ID) code.
Carriage Return, Line Feed if successful

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
COMPRESSOR MODE
REMOTE COMMAND:

$IDMR

090.020-CS (JUNE 11)


Page 33

SLIDE VALVE MODE


AUTOMATIC COMMAND:

$IDVA

Command structure:
Command

Description

Command structure:

Start of command sequence.

Command Description

ID

Compressor (ID) code (01, 14, etc.)

Start of command sequence.

MR

(M)ode (R)emote

ID

Compressor (ID) code (01, 14, etc.)

CS

Checksum

VA

Slide (V)alve Mode (A)utomatic

CR

Carriage Return

CS

Checksum

CR

Carriage Return

RETURNED ANSWER,
Character
Position
1
2, 3

Description of returned data

RETURNED ANSWER,

(A)cknowledge

Character
Position

(ID) code.
Carriage Return, Line Feed if successful

COMPRESSOR SEQUENCE
ACTIVATE COMMAND:

2, 3

(A)cknowledge
(ID) code.
Carriage Return, Line Feed if successful.

$IDS2

SLIDE VALVE MODE


REMOTE COMMAND:

Command structure:
Command

Description of returned data

Description

Start of command sequence.

ID

Compressor (ID) code (01, 14, etc.)

S2

(S)equence Activate (2)

CS

Checksum

Start of command sequence.

CR

Carriage Return

ID

Compressor (ID) code (01, 14, etc.)

VR

Slide (V)alve Mode (R)emote

CS

Checksum

CR

Carriage Return

Command structure:
Command Description

RETURNED ANSWER,
Character
Position
1
2, 3

Description of returned data


(A)cknowledge

RETURNED ANSWER,

(ID) code.
Carriage Return, Line Feed if successful
$IDS3

2, 3

Description of returned data


(A)cknowledge
(ID) code.
Carriage Return, Line Feed if successful.

Command structure:
Description

Start of command sequence.

ID

Compressor (ID) code (01, 14, etc.)

S3

(S)equence Activate (3)

CS

Checksum

CR

Carriage Return

RETURNED ANSWER,
Character
Position

Character
Position
1

COMPRESSOR SEQUENCE
DE-ACTIVATE COMMAND:
Command

$IDVR

Description of returned data

(A)cknowledge

2, 3

(ID) code.
Carriage Return, Line Feed if successful

090.020-CS (JUNE 11)


Page 34

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 35

SECTION 3
QUANTUM LX ALLEN-BRADLEY COMMUNICATION
QUANTUM LX ALLEN-BRADLEY COMMUNICATION
This section contains programming examples for
reading data from and writing data to the Frick Quantum control panel from an Allen Bradley (AB) SLC500
or PLC5 processor. Allen Bradley (AB) RSLogix500
programming software has been used for the following examples, however, these examples can also be
used for the AB RSLogix5 software.
Overview Of Half And Full Duplex Theory
To provide for the reading and writing of data
to Quantum LX panels using Allen-Bradley
communication, the Quantum LX has an AllenBradley DF1 communication driver that recognizes either half or full duplex SLC 500 protected
typed logical read and write commands (either
half or full duplex must be selected). Half-duplex
simply means that data can only be sent in one
direction at a time (the concept of how a walkie-talkie works). Using full-duplex, data can be
sent and received simultaneously (the concept of
how a telephone works). This is a Master / Slave
multi-drop communication method.
The Quantum LX talks Allen-Bradley SLC protocol and is programmed to resemble an AllenBradley SLC500 slave station. The customers
PLC or DCS must be setup to initiate the reading and writing of data to a Quantum LX. The
Quantum LX does not initiate any communications. The panel ID number is used as its station address and the target node. With the AB
PLC, the MSG (Message) instruction is used to
send read and write requests. A DCS (Distributed
Control System) will use a SLC 500 DF1 protocol
driver to send protected typed logical read with
3 address fields and protected typed logical write
requests with 3 address fields to a Quantum
LX. Fifty (50) data elements can be read with one
read.
Setpoints are changed by sending a write command to one element. Changing a setpoint
causes the Quantum LX to save the new setpoint to Flash memory (non-volatile memory).
Be careful not to continuously request a setpoint change. It is to be expected that communications may slow down during the process of writing setpoints or clearing alarms.
Both of these processes involve writing to either EEPROM or Flash Memory and does take
some time. If communication requests are

being sent faster than once every couple of


seconds, there will be temporary slowdowns
during these processes.
Additionally, keeping the Quantum LX busy
writing to Flash memory will interfere with the
communications to its I/O Boards. A communication failure to an I/O board will cause the compressor to shutdown. Control commands such
as starting the compressor are also sent with a
write command. For more detail and a list of the
data, reference the Quantum LX Data Table
section. For details about the actual protocol,
reference the AB publication 1770-6.5.16 DF1
Protocol and Command Set Reference Manual.
Because overrun can occur, the baud rate and
commands should be setup to produce the most
desired throughput. The master station should
have the Stop Bit and Parity set to match the
Quantum LX, Duplicate Detect disabled, and
Error Detect set for BCC or CRC.
When communication is between either your
programming software and a Quantum LX or
an Allen-Bradley PLC and a Quantum LX on
a multi-drop link, the devices depend on a DF1
Master to give each of them polling permission
to transmit in a timely manner. As the number
of Quantum LX slaves increase on the link, the
time between when each panel is polled also
increases. This increase in time may become
larger if you are using low baud rates. As these
time periods grow, the timeouts such as the
message timeout, poll timeout and reply timeout
may need to be changed to avoid loss of communication.
ACK Timeout - The amount of time in 20 milliseconds increments that you want the processor
to wait for an acknowledgment to the message
it has sent before the processor retries the message or the message errors out.
Reply Message Wait Time - Define the amount
of time in 20 millisecond increments that the
master station will wait after receiving an ACK
(to a master-initiate message) before polling the
remote station for a reply. Choose a time that
is, at minimum, equal to the longest time that a
remote station needs to format a reply packet.
Some remote stations can format reply packets
faster than others.
Message Timeout - Defines the amount of time
in seconds that the message will wait for a reply.

090.020-CS (JUNE 11)


Page 36

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

If this time elapses without a reply, the error bit


is set, indicating that the instruction timed out.
A timeout of 0 seconds means that there is no
timer and the message will wait indefinitely for a
reply. Valid range 0-255 seconds.
Note: Make sure the Allen-Bradley PLC and the
programming software is the most recent software revision. Some revisions have been made
that do not allow the SLC Typed Logical Read/
Write Message Command.

SLC-500 - Suggested Setup


The following are representations of the channel
configuration screens from the AB RSLogix500
programming software for the SLC500. Enter
values as shown in order to establish communications via AB Protocol.
CHANNEL CONFIGURATION
Configure the communication channel
Channel 0:
Current Communication Mode: System
Communication Driver: DF1 Half-Duplex
Master or DF1 Full-Duplex
Baud Rate: 19200 (suggested)
Stop Bits: 1 (suggested)
Duplicate Detect: Disabled
ACK Timeout (x20ms): 30
Message Retries: 3
Parity: None (suggested)
Station Address (Source ID): 5 (Masters DF1
selected ID#)
Error Detect: BCC / CRC
RTS off Delay (x20ms): 0
RTS Send Delay (x20ms): 0
Pre-Send Time Delay (x1 ms): 0
Control Line: No Handshaking
Polling Mode: Message Based (do not allow
slave to initiate messages)
Priority Polling Range - Low: 255, High: 0
Normal Polling Range - Low: 255, High: 0
Normal Poll Group Size: 0
Reply Message Wait Time (x20ms): 20
System Mode Driver: DF1 Half-Duplex Master or DF1 Full-Duplex
User Mode Driver: Generic ASCII
Write Protect: DISABLED
Mode Changes: DISABLED
Mode Attention Character: \0x1b (default)
System Mode Character: S (default)
User Mode Character: U (default)
Edit Resource/File Owner Timeout (Sec): 60
Passthru Link ID (decimal): 1
READ MESSAGE SETUP EXAMPLE
Read/Write Message
Type: Peer-To-Peer
Read/Write: Read
Target Device: 500 CPU
Local/Remote: Local

Control Block: N11:0


Control Block Length: 14
Channel: 0
Target Node: 2 (002) (this is the Quantum
Panel ID)
Local File Address: N12:0
Target File Address/Offset: N10:0
Message Length in Elements: 50
Message Time-out (seconds): 15
(Refer to the Allen-Bradley Programming
Overview Section for more information)
WRITE MESSAGE SETUP EXAMPLE
Read/Write Message
Type: Peer-To-Peer
Read/Write: Write
Target Device: 500 CPU
Local/Remote: Local
Control Block: N11:0
Control Block Length: 14
Channel: 0
Target Node: 2 (002) (this is the Quantum
LX Panel ID)
Local File Address: N12:0
Target File Address/Offset: N55:3
Message Length in Elements: 1
Message Time-out (seconds): 15
Enter 20 into N12:0 to send the command to
set the compressor in remote mode.
(Refer to the Allen-Bradley Programming
Overview Section for more information)

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

ALLEN-BRADLEY PROGRAMMING OVERVIEW


This section contains programming examples for
reading data from, and writing data to the Frick
Quantum LX control panel from an Allen Bradley
(AB) SLC500 processor. AB RSLogix500 programming
software has been used for the following examples,
however, these examples can also be used for the AB
RSLogix5 software.

090.020-CS (JUNE 11)


Page 37

CHANNEL CONFIGURATION
The following are representations of the channel
configuration screens from the AB RSLogix500
programming software for the SLC500. Enter
values as shown in order to establish communications via AB Protocol.

General Configuration

090.020-CS (JUNE 11)


Page 38

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

System Configuration

Message Sequence Logic


Use the following logic to sequence read and write

message to the Quantum LX panel. This logic prevents hang up due to lost communications or message errors.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
Message Read Logic
Use the following logic to read data from the Quantum LX panel. To read more data or to read data
from several compressors, copy / paste these rungs
as needed then modify the control block and setup
screen parameters accordingly. The following message read instruction will be executed whenever
counter 5:0 (logic shown above) is equal to 0.

090.020-CS (JUNE 11)


Page 39

Delay Between Messages


The delay timer on rung 3 must be used when communicating to the Quantum LX with the 100ms
preset as shown. This time delay may be decreased
when communicating to more than one compressor
provided the messages are alternated between compressors. This time delay is not required for Quantum V. 5.0x or earlier.

090.020-CS (JUNE 11)


Page 40

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
LX (ID#1) N10:1 register and place them into the
SLC500s N10:1 through N10:28 register. The target
address must be changed to for the Quantum LX.

MESSAGE READ SETUP SCREEN


The following setup screen is programmed to obtain 28 consecutive data files from the Quantum

This Controller: SLC500

Target Device: Quantum Panel

Data Table Address: Data file location in the


SLC500

Data Table Address: Data file location in the


Quantum LX controller.

Size in Elements: # of data file to read

Local Node: Quantum LX ID# (Octal)

Channel: Port location on the SLC processor


(Channel 0 is the RS-232 port)

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
Message Write Logic
Use the following logic to write data from the Quantum LX panel. To write more data or to write data
to several compressors, copy / paste these rungs
as needed then modify the control block and setup

090.020-CS (JUNE 11)


Page 41

screen parameters accordingly. The following write


message instruction will be executed when counter 5:0 (logic shown above) is equal to 1 and when
called upon by the change compressor mode bit B3/2.
When B3/2 is off, the counter will be incremented to
execute the next message in the sequence.

- Continued on next page -

090.020-CS (JUNE 11)


Page 42

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
- Continued from previous page -

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

MESSAGE WRITE SETUP SCREEN


The following setup screen is programmed to write
the compressor mode to the Quantum LX (ID#1)

This Controller: SLC500

Data Table Address: Data file location in the


SLC500
Size in Elements: # of data file to read
Channel: Port location on the SLC processor
(Channel 0 is the RS232 port)

Target Device: Quantum Panel

Data Table Address: Data file location in the


Quantum controller.
Local Node: Quantum ID# (Octal)

Allen-Bradley Data Access


Data passed to and from the Quantum are integer
values with one decimal field assumed unless shown
otherwise or the command is sent to select two decimal fields. For example, if the datas value is 25.5 then
the value 255 is sent. All temperatures are in degree
C and all pressures are in PSIA unless the command
is sent to select the units of the panel. A mode such
as Slide Valve mode is sent as an integer value that
represents the mode it is in. For example, a 0 is sent
if it is in manual, or a 10 is sent if it is in automatic, or
a 20 is sent if it is in Remote Communications.

090.020-CS (JUNE 11)


Page 43

N55:3 data file from the SLC500s N55:3 data file. The
target address must be changed to for the Quantum LX.

The value zero (0) is used to represent an OFF status


and a DISABLED option. The value one (1), which is
received as a 10, is used to represent an ON status
and an ENABLED option. Only data values that are
designated as setpoints are modifiable. Read Only is
used to help identify what data is not modifiable. The
setpoint range is checked to see if it is an allowed
setting. If it is not allowed, the setting is not changed.
Reference the Quantum Data Tables in this manual
for the address listing and description of data.
A command has been provided that selects whether
data to and from the Quantum will be returned in
the units that are the default (pressure in PSIA and
temperature in Degree C) or in the units that are selected to display at the panel.

EtherNet/IP
Frick Controls supports the use of EtherNet/IP (as
described on the ab.com website, under the EtherNet/IP heading) with LX software 6.06 and later. Address mapping follows the Allen-Bradley N: format,
as shown in the Data Tables under the heading of AB
Address. Although this protocol is basically self-configuring, if you do have additional questions, please
contact Frick Controls.

090.020-CS (JUNE 11)


Page 44

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 45

SECTION 4
MODBUS PROTOCOL
MODBUS Protocol
General Description
MODBUS Protocol is a messaging structure developed by Modicon in 1979, used to establish
master-slave/client-server communication between intelligent devices. It is a standard, truly
open and the most widely used network protocol
in the industrial manufacturing environment. The
MODBUS protocol provides an industry standard method that MODBUS devices use for
parsing messages.
Since MODBUS protocol is a messaging structure, it is independent of the underlying physical
layer. It is traditionally implemented using RS232, RS-422, or RS-485 communications hardware. With the Quantum LX, MODBUS TCP
can also be utilized as it applies to Ethernet networks.
The Quantum controller is setup to communicate on standard MODBUS networks using
either ASCII (American Standard Code for Information Interchange), RTU or TCP/IP.
The Quantum provides the capability to interface with other devices that support serial data
communications using the MODBUS protocol.
This is a Master / Slave multi-drop communication method whereby the Quantum is setup to
be a MODBUS Slave. The customers PLC (Programmable Logic Controller) or DCS (Data Communications System, such as a desktop or laptop
computer) must be setup as a MODBUS Master.
The Master initiates the reading and writing of
data (queries) to a Quantum. The Quantum
does not generate its own data, it will only reply
to a request by the Master.
The Quantum ID number is used as the MODBUS Slave address (for ASCII and RTU). The
Master uses Function Code 3 (Read Holding
Registers) to send a request to read data from
the Quantum. The Master uses Function Code
6 (Load Register) to request to change a setpoint or to send a command such as starting the
compressor. Up to one hundred and twenty-five
(125) data elements can be read with one read
request.
The address references are numbered relative to the Frick addresses in the Quantum
Data Table (see MODBUS Addressing Note in the
Quantum Data Table section of this manual for
additional information). The Quantum only accepts one value with a Load Register request.

Changing a setpoint causes the Quantum to


save the new setpoint to nonvolatile memory.
Be careful not to continuously request a setpoint
change. Keeping the Quantum busy writing to
memory will interfere with the Quantum communicating to its I/O boards. A communication
failure to an I/O board will cause the compressor to shutdown. For more detail and a list of
the data, reference the Quantum Data Table
section of this manual. For details about the actual protocol, reference the Modicon website at
http://www.modbus.com.

MODBUS TCP/IP (Ethernet)


TCP/IP is the common transport protocol of the
Internet and is actually a set of layered protocols, providing a reliable data transport highway
between Quantum LX panels and an Ethernet
network. Ethernet has become the standard for
factory networking, replacing many of the databus systems used in the past.
MODBUS TCP/IP simply takes the MODBUS
instruction set and transparently wraps TCP/
IP around it. Unlike MODBUS ASCII and RTU,
there no parameters that need to be set (such as
baud rate, data bits, etc.).
NOTE: When using Modicon Setup Software, ensure that:

Head number = Rack Position (position


of Ethernet card in its rack)
Socket # = 502

Frick Controls utilizes function codes 3 (Read),


6 (Write) and 16 (Multiple Write) of the TCP/IP
protocol. Use port 502 for Modbus TCP/IP communications. The value used for the Modbus ID
must be greater than zero.

MODBUS TCP LOG

090.020-CS (JUNE 11)


Page 46

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

The following user selectable button is provided:

This screen allows the technician to view the


ModBus TCP data communications information
that the Quantum LX is receiving and transmitting.

The top line of data is the most recent activity.


At the left of each line, you should see whether
the data is IN or OUT (Response or Command),
and the actual data (in Hexadecimal format). This
information can be used to compare against the
data being sent and received at the other end of
the communications link, to verify proper operation.

Each time a new command is sent or received,


the screen will need to be refreshed by selecting
the [Refresh] button.

Refer to the following table for an example of


how the data packets are created, using the data
that has been shown on the above screen.

[Refresh]

Byte Count in data returned


Data in register 2000
Data in register 2001
Response 01 Out:

00 00

00 00

00 07

01

03

04 00 20 00

Command 00 In:

00 . 00

00 . 00

00 . 06

01

03

07 . D0 00 . 02

16

# of registers to read
Address of first register (2000)
Read Holding register
Modbus ID
# of bytes in command
Always 0 for Modbus TCP
Transaction Identifer

MODBUS ASCII (Serial Communications)


In the ASCII Transmission Mode (American Standard Code for Information Interchange), each
character byte in a message is sent as 2 ASCII
characters. This mode allows time intervals of
up to a second between characters during transmission without generating errors. Some particulars about MODBUS ASCII:

The device address field of the message


frame contains two characters (16 bits).
The function code field of the message
frame will contain two characters (16
bits).
Word size is selectable.
Error checking is accomplished using
LRC (Longitudinal Redundancy Check).
Hyperterminal can be used to test communications.

MODBUS RTU (Serial Communications)


In RTU (Remote Terminal Unit) Mode, each 8-bit
message byte contains two 4-bit hexadecimal
characters, and the message is transmitted in a
continuous stream. The greater effective char-

acter density increases throughput over ASCII


mode at the same baud rate. Some particulars
about MODBUS RTU:

The device address field of the message


frame contains 8 binary bits.
The function code field of the message
frame will contain 8 binary bits
Word size is selectable.
Error checking is accomplished using
CRC (Cyclical Redundancy Check).
Hyperterminal cannot be used to test
communications.

Serial Port Configuration Of The Master


7 or 8 Bits per Character (Data Bits)
Odd, Even or No Parity
1 or 2 Stop Bits
No Handshake

Data Packet
The MODBUS protocol establishes the format
for the Master's query by creating a message
(data packet) as follows:

Assign the device address (Quantum

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

panel ID #). The address field of a message frame contains two characters for
ASCII, or 8 bits for RTU. Valid Quantum device addresses are in the range
of 01 99 decimal. A master addresses
a Quantum by placing the Quantum
address in the address field of the message. When the Quantum sends its
response, it places its own address in
this address field of the response to let
the Master know which Quantum is
responding.
An 8-bit function code defining the requested action (Query):
Function Code 3 - to read holding registers (sends a request to read data from
the Quantum).
Function Code 6 to load a register (to
request to change a setpoint or to send
a command such as starting the compressor), or a function code 16 (RTU
only) to load multiple registers.
Any data to be sent (Response). The
data field is constructed using sets of
two hexadecimal digits, in the range of
00 to FF hexadecimal. These are to be
made from a pair of ASCII characters
(ASCII), or one 8-bit for RTU. The data
field of messages sent from a Master to
the Quantum devices contains additional information which the Quantum
must use to take the action defined
by the function code. This can include
items like discrete and register addresses, the quantity of items to be handled,
and the count of actual data bytes in the
field. If no error occurs, the data field
of a response from a Quantum to a
Master contains the data requested. If
an error occurs, the field contains an
exception code that the Master application can use to determine the next action to be taken.
An error-checking field.

The Query
The function code in the query tells the addressed Quantum what kind of action to perform. The data bytes contain any additional information that the Quantum will need to perform
the function. For example, function code 03 will
query the Quantum to read holding registers
and respond with their contents. The data field
must contain the information telling the Quantum which register to start at and how many
registers to read. The error check field provides a
method for the Quantum to validate the integrity of the message contents.

The Response
If the Quantum makes a normal response, the
function code in the response is an echo of the

090.020-CS (JUNE 11)


Page 47

function code in the query. The data bytes contain the data collected by the Quantum, such
as register values or status. If an error occurs,
the function code is modified to indicate that the
response is an error response, and the data bytes
contain a code that describes the error. The error check field allows the master to confirm that
the message contents are valid.

Data Field
The data field is constructed using sets of two
hexadecimal digits, in the range of 00 to FF
hexadecimal. For ASCII, these can be made from
a pair of ASCII characters. For RTU, this is one
8-bit number.
The data field of messages sent from a master
to the Quantum devices contains additional information which the Quantum must use to take
the action defined by the function code. This can
include items like discrete and register addresses, the quantity of items to be handled, and the
count of actual data bytes in the field.
For example, if the master requests a Quantum to read a group of holding registers (function code 03), the data field specifies the starting
register and how many registers are to be read.
If no error occurs, the data field of a response
from a Quantum to a Master contains the data
requested. If an error occurs, the field contains
an exception code that the Master application
can use to determine the next action to be taken.

Error Checking
ASCII
In ASCII mode, when data is transmitted to
and from the Quantum Controller, each
message has an Error Checking value appended to the end of the message. Longitudinal Redundancy Check, or LRC, is used as
the method for verifying that the ASCII message sent from the transmitting device was
properly received by the receiving device.
The Longitudinal Redundancy Check (LRC)
field is one byte, containing an eight-bit binary value. The LRC value is calculated by
the transmitting device, by adding together
successive eight-bit bytes of the message,
discarding any carries, and then two's complementing the result. It is performed on the
ASCII message field contents excluding the
colon character that begins the message,
and excluding the CRLF pair at the end of the
message. The LRC is then appended to the
message as the last field preceding the CRLF
(Carriage Line Feed) characters. Each new
addition of a character that would result in
a value higher than 255 decimal simply rolls

090.020-CS (JUNE 11)


Page 48

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

Framing

over the field's value through zero. Because


there is no ninth bit, the carry is discarded
automatically.

A message frame is used to mark the beginning


and ending point of a message allowing the receiving device to determine which device is being addressed and to know when the message is
completed. It also allows partial messages to be
detected and errors flagged as a result.

The receiving device recalculates an LRC


during receipt of the message, and compares the calculated value to the actual
value it received in the LRC field. If the two
values are not equal, an error results.

ASCII

RTU

In ASCII mode, messages start with a


colon ( : ) character (3A hex), and end
with a carriage return-line feed (CRLF)
pair (0D and 0A hex).

In RTU mode, messages include an error


checking field that is based on a Cyclical
Redundancy Check (CRC) method. The CRC
field checks the contents of the entire message. It is applied regardless of any parity
check method used for the individual characters of the message.

The allowable characters transmitted


for all other fields are hexadecimal 0 9, A - F.
All Quantum panels connected to the
network monitor the network bus continuously for the colon character. When
one is received, each Quantum decodes the next field (the address field)
to find out if it is the addressed device.

The CRC field is two bytes, containing a 16


bit binary value. The CRC value is calculated
by the transmitting device, which appends
the CRC to the message. The receiving device recalculates a CRC during receipt of
the message, and compares the calculated
value to the actual value it received in the
CRC field. If the two values are not equal an
error results.

A MODBUS message is placed by


the transmitting device into a frame
that has a known beginning and ending point. This allows receiving devices
to begin at the start of the message,
read the address portion and determine
which device is addressed, and to know
when the message is completed. Partial
messages can be detected and errors
can be set as a result.

The CRC is started by first preloading a 16


bit register to all 1s. Then a process begins of applying successive 8bit bytes of
the message to the current contents of the
register. Only the eight bits of data in each
character are used for generating the CRC.
Start and stop bits, and the parity bit, do not
apply to the CRC.
During generation of the CRC, each 8bit
character is exclusive ORed with the register contents. Then the result is shifted in the
direction of the least significant bit (LSB),
with a zero filled into the most significant
bit (MSB) position. The LSB is extracted and
examined. If the LSB was a 1, the register
is then exclusive ORed with a preset, fixed
value. If the LSB was a 0, no exclusive OR
takes place.
This process is repeated until eight shifts
have been performed. After the last (eighth)
shift, the next 8bit byte is exclusive ORed
with the registers current value, and the
process repeats for eight more shifts as described above. The final contents of the register, after all the bytes of the message have
been applied, is the CRC value.
When the CRC is appended to the message,
the low-order byte is appended first, followed by the high-order byte.

A typical message frame as sent by the


Master is shown below:
START

ADDRESS

FUNCTION

DATA

LRC
CHECK

END

01

03

00870001

74

CRLF

1
CHAR

2
CHAR

2
CHAR

8
CHAR

2
CHAR

2
CHAR

Start of
message

Quantum Function
ID

CRC Error
Correction
Code

End of
message

00 = H. O. Address
87 = L. O. Address
00 = H. O. # of data registers
01 = L. O. # of data registers

RTU
In RTU mode, messages start with a
silent interval of at least 3.5 character
times. This is most easily implemented
as a multiple of character times at the
baud rate that is being used on the network (shown as T1T2T3T4 in the
figure below). The first field then transmitted is the device address.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

START

ADDRESS FUNCTION

T1-T2-T3-T4

8 Bits

Start of Quantum
message
ID

8 Bits

DATA

LRC
CHECK

END

Nx8
Bits

16 Bits

T1-T2-T3-T4

Function

CRC Error
Correction
Code

End of
message

00 = H. O. Address
87 = L. O. Address
00 = H. O. # of data registers
01 = L. O. # of data registers

ASCII Query (Read) Example


To demonstrate how an address within the
Quantum may be read, the following test can
be performed using Windows HyperTerminal
(NOTE: Hyperterminal cannot be used to test
RTU or TCP/IP):
As an example, a MODBUS command will be
created and sent to obtain the actual Discharge
Pressure value of a compressor. Using the address tables found later in this manual, locate the
address for Discharge Pressure. In this case, it is
Frick Address 2003 (decimal). Since this is the
only address we are interested in obtaining the

01 03 07 D3 00 01 21 CRLF

Where:
Message Start:
Quantum ID #:
Read Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Registers:
L. O. # of Data Registers:
Error Correction Code:
Carriage Return - Line Feed:

Look at this message on a more basic level, to


understand how the address that we are requesting is arrived at. We want to know the actual value of the Discharge Pressure, Frick Address 2003 (decimal).
The first part of the message will be a Colon
(:). This represents a heads up alert that data is
coming:

Following the last transmitted character, a similar interval of at least 3.5


character times marks the end of the
message. A new message can begin
after this interval. The entire message
frame must be transmitted as a continuous stream. If a silent interval of more
than 1.5 character times occurs before
completion of the frame, the receiving
device flushes the incomplete message
and assumes that the next byte will be
the address field of a new message.
Similarly, if a new message begins earlier than 3.5 character times following a previous message, the receiving
device will consider it a continuation
of the previous message. This will set
an error, as the value in the final CRC
field will not be valid for the combined
messages. A typical message frame is
shown below:

value of, send the following message:

01 06 1B EE 03 E8 05 CRLF

Where:
Message Start:
Quantum ID #:
Write Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Value:
L. O. # of Data Value:
Error Correction Code:
Carriage Return - Line Feed:

Any time that a message is sent, all of the Quantum panels on the MODBUS network will
become active, communications-wise, once the
Colon appears. Next, the panels will look at the
first byte following the Colon ( : ). If this byte
equals the Panel ID # of the particular Quantum
being queried, it will immediately finish reading
the remainder of the message. If the byte does
not equal its ID #, the message will be ignored.

The allowable characters transmitted for all fields are hexadecimal 09,
AF. Networked devices monitor the
network bus continuously, including
during the silent intervals. When the
first field (the address field) is received,
each device decodes it to find out if it is
the addressed device.

090.020-CS (JUNE 11)


Page 49

01 06 1B EE 03 E8 05 CRLF

Where:
Message Start:
Quantum ID #:
Write Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Value:
L. O. # of Data Value:
Error Correction Code:
Carriage Return - Line Feed:

090.020-CS (JUNE 11)


Page 50

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

In this particular example, we are strictly looking


to request to view a data value, so we will be
performing a read function (03):
:

01 03 07 D3 00 01 21 CRLF

Where:
Message Start:
Quantum ID #:
Read Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Registers:
L. O. # of Data Registers:
Error Correction Code:
Carriage Return - Line Feed:

01 + 03 + 07 + D3 + 00 + 01 = DF hex
Next, subtract DF (hex) from 100 (hex):

100 (hex) - DF (hex) = 21 (hex)


:

22003 decimal equals 07D3 hex. Looking at our


example, we see that we need a H.O. (High Order) address and a L.O. (Low Order) address.
Since all data sent and received is in ASCII Hex
Byte format, we need to look at D3 Hex as the
Low Order portion of the address. The High Order portion is 07. Now our decimal 2003 is formatted as 07D3 Hex.
:

01 03 07 D3 00 01 21 CRLF

01 03 07 D3 00 01 21 CRLF

Where:
Message Start:
Quantum ID #:
Read Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Registers:
L. O. # of Data Registers:
Error Correction Code:
Carriage Return - Line Feed:

After the entire data packet has been created,


simply press the [Enter] key, a Line Feed will automatically be sent also.

Where:
Message Start:
Quantum ID #:
Read Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Registers:
L. O. # of Data Registers:
Error Correction Code:
Carriage Return - Line Feed:

Since we are only looking for this one address,


and no other, we can say that we are only looking for one Data Address. Our Data Address part
of the data packet is also looking for a High and a
Low Order value. Fortunately, the number one (1)
is the same in decimal as it is in Hex, therefore,
the Low Order Address is 01 (hex). The High Order Address is 00 (hex), so our decimal 1 is formatted as 0001 (hex).
:

In order to ensure that the Quantum in question receives the data request accurately, we
must append an Error Check byte to the end of
the message. This is accomplished by adding
each of the byte pairs (hex) that we have generated thus far:

01 03 07 D3 00 01 21 CRLF

Where:
Message Start:
Quantum ID #:
Read Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Registers:
L. O. # of Data Registers:
Error Correction Code:
Carriage Return - Line Feed:

ASCII Write Example


To demonstrate how an address within the
Quantum LX may be written to, the following
test can be performed using Windows HyperTerminal (NOTE: Hyperterminal cannot be used to
test RTU or TCP/IP communications).

01 03 07 D3 00 01 21 CRLF

Where:
Message Start:
Quantum ID #:
Read Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Registers:
L. O. # of Data Registers:
Error Correction Code:
Carriage Return - Line Feed:

As an example, a MODBUS command will be


created and sent to the Quantum to set Regulation Mode 1 Setpoint to 100.0 PSIA. First, be
aware that data sent to and received by the
Quantum has one decimal place assumed. This
means that to send the value of 100.0, you actually need to send 1000. Using the address tables
found later in this manual, locate the address for
the Regulation Mode 1 Setpoint. In this case, it
would be Frick Address 7150 (decimal).

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

01 06 1B EE 03 E8 05 CRLF

Where:
Message Start:
Quantum ID #:
Write Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Value:
L. O. # of Data Value:
Error Correction Code:
Carriage Return - Line Feed:

Look at this message on a more basic level, to


understand how the address that we are writing
to is arrived at. We want to send the value of
1000 (100.0) to the Regulation Mode 1 Setpoint,
Frick Address 7150 (decimal).

01 06 1B EE 03 E8 05 CRLF

Where:
Message Start:
Quantum ID #:
Write Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Value:
L. O. # of Data Value:
Error Correction Code:
Carriage Return - Line Feed:

7150 decimal equals 1BEE hex. Looking at our


example we see that we need a H.O. (High Order) address and a L.O. (Low Order) address.
Since all data sent and received is in ASCII Hex
Byte format, we need to look at EE Hex as the
Low Order portion of the address. The High Order portion is 1B. Now our decimal 7150 is formatted as 1BEE Hex.

01 06 1B EE 03 E8 05 CRLF

Where:
Message Start:
Quantum ID #:
Write Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Value:
L. O. # of Data Value:
Error Correction Code:
Carriage Return - Line Feed:

Any time that a message is sent, all of the Quantum panels that are on the MODBUS network
will become active, communications wise, once
the Colon appears. Next, all panels will look at
the first byte following the Colon (:). If this byte
equals the Panel ID # of the particular Quantum
being queried, it will immediately finish reading
the remainder of the message. If the byte does
not equal its ID #, the message will be ignored.
:

01 06 1B EE 03 E8 05 CRLF

Where:
Message Start:
Quantum ID #:
Write Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Value:
L. O. # of Data Value:
Error Correction Code:
Carriage Return - Line Feed:

01 06 1B EE 03 E8 05 CRLF

Where:
Message Start:
Quantum ID #:
Write Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Value:
L. O. # of Data Value:
Error Correction Code:
Carriage Return - Line Feed:

The value that we wish to send is 100.0 (1000).


The Data Value part of the data packet is looking
for a High and a Low Order value. The number
1000 (dec) must be converted to hexadecimal.
This conversion results in a value of 03E8 (hex).
Separating 03E8 into two bytes results in the
Low Order Value of E8 (hex) and the High Order
Value of 03 (hex):

The first part of the message will be a Colon


(:). This represents a heads up alert that data is
coming down the line.

In this particular example, we are strictly looking


to write a data value, so we will be performing a
write function (06):

Since this is the only address we are interested


in writing to, send the following message:

090.020-CS (JUNE 11)


Page 51

01 06 1B EE 03 E8 05 CRLF

Where:
Message Start:
Quantum ID #:
Write Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Value:
L. O. # of Data Value:
Error Correction Code:
Carriage Return - Line Feed:

In order to ensure that the Quantum in question receives the data request accurately, we
must append an Error Check byte to the end of

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

01 + 06 + 1B + EE + 03 + E8 = 1FB hex
Normally, we would subtract 1FB (hex) from 100
(hex), as in the previous read example. However,
in this case we see that 1FB hex is greater than
100 hex. Since the math in this particular example would yield a negative number (FFFF FFFF
FFFF FF05), we need to modify the value of 1FB
in order to provide a positive result. This is accomplished quite simply by dropping the most
left hand digit (1FB becomes FB), and then subtracting FB hex from 100 hex:

100 (hex) - FB (hex) = 05 (hex)


01 06 1B EE 03 E8 05 CRLF

Where:
Message Start:
Quantum ID #:
Write Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Value:
L. O. # of Data Value:
Error Correction Code:
Carriage Return - Line Feed:

01 03 02 05 D0 25

Where:
Message Start:
Quantum ID #:
Read Function:
# of Bytes Returned:
Data:
Error Correction Code:

Once again, the first part of the message will be


a Colon (:). This represents a heads up alert that
data is coming down the line, but since the data
is coming from the Quantum to the Master this
time, the Master will accept it.

}
01 03 02 05 D0 25

Where:
Message Start:
Quantum ID #:
Read Function:
# of Bytes Returned:
Data:
Error Correction Code:

Now that the Master knows which panel is responding, it needs to known which function the
panel is responding to. In this case, it sees that it
is a read function, and the Quantum is merely
returning a value that was previously requested.
:

01 03 02 05 D0 25

}
01 06 1B EE 03 E8 05 CRLF

Where:
Message Start:
Quantum ID #:
Write Function:
H. O. address (hex):
L. O. address (hex):
H. O. # of Data Value:
L. O. # of Data Value:
Error Correction Code:
Carriage Return - Line Feed:

After having received the Colon (:), the Master


will look at the two bytes that follows it, so that it
may determine from which Quantum the message is coming from.

After the entire data packet has been created,


simply press the [Enter] key, a Line Feed will automatically be sent also.
:

If the packet was properly received by the Quantum, you should see an immediate response
in HyperTerminal. In the Query Response (read
function) example used earlier, a response of
:01030205D025 (hex) was received.

ASCII Response Example

the message. This is accomplished by adding


each of the byte pairs (hex) that we have generated thus far:

090.020-CS (JUNE 11)


Page 52

Where:
Message Start:
Quantum ID #:
Read Function:
# of Bytes Returned:
Data:
Error Correction Code:

The next byte tells the Master how many bytes

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

01 03 02 05 D0 25

Where:
Message Start:
Quantum ID #:
Read Function:
# of Bytes Returned:
Data:
Error Correction Code:

} }

The next two bytes (in this case) are the actual
data in response to our original request.
:

(NOTE: Hyperterminal cannot be used to test


RTU):

RTU Query (Read) Example

of information are being returned as a response.


In this case, there are two (2) bytes of valid data.

01 03 02 05 D0 25

Where:
Message Start:
Quantum ID #:
Read Function:
# of Bytes Returned:
Data:
Error Correction Code:

We need to know what this value means. To


break it down, we must convert the pair of bytes
from Hex to Decimal:

In the following example, a MODBUS command


is sent to obtain the actual Discharge Pressure
value of a compressor. Refer to the following example to see what this message packet would
look like:
START

ADD.

FUNC.

T1-T2-T3-T4

01

03

From the previous paragraph, we can assume


that there is one decimal place to be applied to
the data value that was returned. Therefore:
1488 (decimal) = 148.8 (decimal)
All temperatures are in degrees C and all pressures are in PSIA unless the command is sent to
select the units of the panel. Therefore:
148.8 (decimal) = 148.8 PSIA

# OF
STARTING
CRC
REGISTERS
ADDRESS
CHECK
TO LOAD
07

D3

00

01

END

* T1-T2-T3-T4

End of
CRC Error message
Correction
Code

Start of Quantum
message
ID Function
03 = Read
07 = H. O. Address
D3 = L.O. Address

00 = H.O. # of Data Registers


01 = L.O. # of Data Registers

* The CRC value is calculated by the transmitting device, which appends the CRC to
the message.

RTU Response Example


Using the RTU Read example just shown, a typical response would look like:

05DO (hex) = 1488 (decimal)


Data to and from the Quantum are integer
values with one decimal field assumed unless
shown otherwise or the command is sent to select two decimal fields.

090.020-CS (JUNE 11)


Page 53

START

ADD.

T1-T2-T3-T4

01

BYTE
CRC
FUNC. COUNT TO ANSWER
CHECK
FOLLOW
03

02

04

Start of Quantum
message
ID Function
03 = Read
02 = 2 Bytes

23

END

* T1-T2-T3-T4

End of
CRC Error message
Correction
Code

04 = H.O. Value
23 = L.O. Value

The returned value in the above example is 0423


hex. Converting this to decimal equates to 1059,
and assuming a decimal point gives an answer of
105.9 (PSIA or Panel units, depending on which
has been selected).

Notes:

090.020-CS (JUNE 11)


Page 54

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

MODBUS NOTES
This has been an example of how the Quantum
Controller uses the MODBUS Protocol. It is hoped
that the information provided here will assist the end
user in writing applications that will allow the Quantum to be implemented into networks that the customer may already have in use.
This information is subject to change at any time, and
is provided as a reference only. Not all areas of the
MODBUS Protocol can be handled in this document.
Some additional information regarding MODBUS
Protocol that the end user should be aware of:

There are many versions of MODBUS Protocol


that are available, and an application that works
properly on one system, may not function identically on another.

Some versions of MODBUS Protocol may require the user to increment any referenced addresses by 1 (one). For instance, if you wanted
to look at Frick Address 2003, you may need
to actually look at address 2004. The Quantum
addressing begins at 0 (zero), whereas some
MODBUS Protocols begin at 1 (one), therefore,
you may need to compensate.

7 or 8 bits selectable.

1 or 2 Stop bits selectable.

Parity can be set to None, Odd or Even

When using MODBUS protocol (other than the


Hyperterminal example shown earlier), it is necessary to use the MODBUS Address column as
shown in the Quantum Data Tables. These addresses should work for most applications.

Follow the Frick specifications for data communications requirements.


Hyperterminal can be used to test ASCII, but not

RTU or TCP/IP communications.


NOTE: Be careful not to continuously request a setpoint change. It is to be expected that communications may slow down during the process of writing
setpoints or clearing alarms. Both of these processes
involve writing to either EEPROM or Flash Memory
and does take some time. If communication requests
are being sent faster than once every couple of seconds, there will be temporary slowdowns during
these processes.
MODBUS Data Access
Data passed to and from the Quantum are integer
values with one decimal field assumed unless shown
otherwise or the command is sent to select two decimal fields. For example, if the datas value is 25.5 then
the value 255 is sent. All temperatures are in degree C
and all pressures are in PSIA unless the command is
sent to select the units of the panel. A mode such as
Slide Valve mode is sent as an integer value that represents the mode it is in. For example, a 0 is sent if it
is in manual, or a 10 is sent if it is in automatic, or a
20 is sent if it is in remote. The value zero (0) is used
to represent an OFF status and a DISABLED option.
The value one (1), which is received as a 10, is used
to represent an ON status and an ENABLED option.
Only data values that are designated as setpoints are
modifiable. Read Only is used to help identify what
data is not modifiable. The setpoint range is checked
to see if it is an allowed setting. If it is not allowed,
the setting is not changed. Reference the Quantum
Data Tables in this manual for the address listing and
description of data.
A command has been provided that selects whether
data to and from the Quantum will be returned in
the units that are the default (pressure in PSIA and
temperature in Degree C) or in the units that are selected to display at the panel.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 55

SECTION 5
HYPERTERMINAL
perterminal program. (Hyperterminal is usually
found in the Accessories folder). If Hyperterminal
can't be found there, try using the Find File command, and search the entire hard drive.

DESCRIPTION
HyperTerminal is a terminal emulation program which
resides in the Microsoft Windows environment, and
as such, will normally be found on any computer that
is running Microsoft Windows. HyperTerminal provides a method by which the end user may verify
conclusively that their Quantum controller is functioning properly, and as designed, with respect to external communications to remote devices.

Be aware that the screens that are actually


shown on the test computer may or may not appear exactly as shown here. Various versions of
Windows can affect the appearance, as well as
whether or not the screen has been maximized,
or if it has been scaled to a smaller size. Regardless of how the screen work appears, the
function of the screen work is what is important,
and that function is not affected by the way the
screen looks.

Once Hyperterminal has been located, execute


it. A dialog box will appear. You will be prompted
to enter a name for the New Connection. Type
in whatever name you would like to use, Frick
was used in this example. This name will also
create a file once you are finished, saving all of
the setup parameters for future use. It is recommended that a name be chosen to reflect the
type of Protocol that you will be using as you
may wish to setup for various protocols. Once
you have entered a name, click [OK].

NOTE: Hyperterminal can only be used to test


MODBUS ASCII. It CANNOT be used to test Allen-Bradley or MODBUS RTU or TCP/IP.
Many times, the Quantum controller will be installed into an environment whereby the end user
wishes to communicate to it, either through a PLC
(Programmable Logic Controller), a desktop computer for the purpose of monitoring/controlling plant
operations through HMI (Human Machine Interface),
or any number of other communications applications.
The purpose of this desired communications typically
involves viewing and changing setpoints, starting and
stopping a compressor, viewing alarm and shutdown
information, and viewing current operating conditions.
When first connecting a Quantum panel to a communications network, it would be highly desirable to
determine that all necessary parameters (jumper settings, panel setup, and cabling) are properly met so
that communications may be established quickly with
the Quantum, so that time is not lost in trying to
troubleshoot a potentially simple problem.
A connection from a Comm port of a computer running Microsoft Windows can be used to connect to a
serial port of the Quantum.
SETTING UP HYPERTERMINAL

You will need to locate either a lap top or desktop computer that has Hyperterminal installed.

Turn on the power for the lap top.

After the laptop has fully booted, locate the Hy-

A new dialog box will be shown asking to select a


Com port (choose the Com port that your communications cable is attached to, this will normally be
Com-1). The phone number box should be blank.
Click on [OK].

090.020-CS (JUNE 11)


Page 56

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

The Com-1 properties dialog box will now appear.


The parameters in this box must match the requirements of the protocol that you are wishing to use.
The one box that normally would need to be changed
from one protocol to the next is the Data Bits box.

A pull down menu will appear. From this menu, locate


and click on [Properties]. You will once again see the
following screen. This time, click on the [Settings]
tab.

For the purpose of this document, Frick # protocol


will be used. Refer to the MODBUS ASCII section of
this manual for information on MODBUS.
Set the five boxes as follows, then click [OK].

Bits per second:


Quantum)

Data bits:

Parity:

Stop Bits:

Flow Control:

9600 (must match the


8
None
1
None

The following screen will appear. This is the screen


whereby all communications (out of the computer,
and into it) will be shown. When valid data is typed in
here, then sent, the connected device recognizes and
responds to that data, and a response will be shown
below the sent data. Click on [File].

The computer will need to be set up to match the


documentation as presented here, for everything to
look and work as shown later. To do this, click on the
[ASCII Setup] button.

On the ASCII Setup screen, for best results, check the


boxes according to the following chart:

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 57

For MODBUS ASCII:

Send line ends with line feeds


Echo typed characters locally
Append line feeds to incoming line ends
Wrap lines that exceed terminal width

For Frick protocols (# and $):

Echo typed characters locally


Append line feeds to incoming line ends
Wrap lines that exceed terminal width

Leave everything else on this dialog box unchanged,


then click on [OK].
TESTING COMMUNICATIONS
Set the keyboard for CAPS (so that all capital letters
will be typed). Type in the following command: #01I,
then press [ENTER]. (This command will request the
Quantum with ID 01 to send a packet of Information.)

The Properties screen will once again be shown. Click


on the [OK] button to proceed.

If the communications is working properly, there


should be an immediate response from the first
Quantum. The response should look something
(but not necessarily exactly) like #01I000AOMN609.
If this portion of the test has passed, you can try
to communicate to the next (or any Quantum), by
changing the value that you type into the HyperTerminal screen as follows:
You will now be back to the main Hyperterminal
communications screen. This screen will be blank. All
communications, both from the computer, and to the
computer (from the Quantum), will appear on this
screen. Proceed to the Testing Communications section.

Instead of [#01], replace the 01 portion with the


ID that you would like to access. For instance,
if you wanted to talk to a fourth Quantum (ID
4), type in [#04]. This should return a message
from that Quantum.
This has been just a brief description of how to check
your communications and verify that it is working.
Greater detail can be found by consulting tables for
each of the protocols in this manual.

090.020-CS (JUNE 11)


Page 58

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

General Notes
Ensure that the Quantum communications parameters are correct. This setup can be found on the Communications screen. This info must match that of the
device that you are trying to talk to at the other end.
There are two red LEDs associated with the Comm
port on the Quantum (TX & RX). Ensure that neither of these LEDs are on continuously. If one or
the other (or both) are on constantly, disconnect the
Com cable. If the status of the LEDs does not change,
check the wiring connections to the comm port. Ensure that the wiring is not backwards. If the wiring is
correct, power the Quantum down, then back up. If
either or both of the LEDs is still on, a bad driver chip
may be suspected on the Quantum, and the board
should be replaced.
Once everything has been inspected (cables, jumpers, and setup), try to develop communications from
the master. You should see the LEDs on the Comm
port flickering as the Quantum talks to the master.
If nothing happens, it would be best to consult the
HyperTerminal section of this manual for more detailed troubleshooting.
If no data appears, or if the data does not match the
specific protocol requirements that you are using,
then check the following:

Verify that the communications wiring


matches that shown in the drawings at the
end of this manual.
Access the Communications screen and

verify that the Quantum ID is set to the


same value that you are trying to access.
Also, check that the baud rate matches that
of the setup in the properties section of the
Hyperterminal example.

Verify the position of the jumpers by comparing them with the section entitled Quantum Communications Jumpers.

Ensure that the data that you have entered


in Hyperterminal, exactly matches the example.

Go back through the Setting up Hyperterminal section, and ensure that it has been
followed exactly. Repeat the process if necessary.

If you are using a converter card (to convert


the RS-232 signal from the computer to RS422 or RS-485), then either verify that the
converter card is working properly with a
different piece of known functioning equipment, or eliminate it completely by tying
into the Quantum directly through RS-232
(Quantum 4 only).

The Communications port on the computer


is bad. Try to verify this by communicating
to a different piece of known good equipment.

The Communications port on the Quantum is bad.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 59

CONVERSION CHART FOR DECIMAL / HEXADECIMAL / ASCII


Decimal
(DEC)

Hexadecimal
(HEX)

ASCII

Decimal
(DEC)

Hexadecimal
(HEX)

ASCII

Decimal
(DEC)

Hexadecimal
(HEX)

ASCII

ctrl @ NUL

43

2B

86

56

ctrl A SOH

44

2C

87

57

ctrl B STX

45

2D

88

58

ctrl C ETX

46

2E

89

59

ctrl D EOT

47

2F

90

5A

ctrl E ENQ

48

30

91

5B

ctrl F ACK

49

31

92

5C

ctrl G BEL

50

32

93

5D

ctrl H BS

51

33

94

5E

^
_

ctrl I HT

52

34

95

5F

10

ctrl J LF

53

35

96

60

'

11

ctrl K VT

54

36

97

61

12

ctrl L FF

55

37

98

62

13

ctrl M CR

56

38

99

63

14

ctrl N SO

57

39

100

64

15

ctrl O SI

58

3A

101

65

16

10

ctrl P DLE

59

3B

102

66

17

11

ctrl Q DC1

60

3C

<

103

67

18

12

ctrl R DC2

61

3D

104

68

19

13

ctrl S DC3

62

3E

>

105

69

20

14

ctrl T DC4

63

3F

106

6A

21

15

ctrl U NAK

64

40

107

6B

22

16

ctrl V SYN

65

41

108

6C

23

17

ctrl W ETB

66

42

109

6D

24

18

ctrl X CAN

67

43

110

6E

n
o

25

19

ctrl Y EM

68

44

111

6F

26

1A

ctrl Z SUB

69

45

112

70

27

1B

ctrl [ ESC

70

46

113

71

28

1C

ctrl \ FS

71

47

114

72

29

1D

ctrl ] GS

72

48

115

73

30

1E

ctrl ^ RS

73

49

116

74

31

1F

ctrl _ US

74

4A

117

75

32

20

SPACE

75

4B

118

76

33

21

76

4C

119

77

34

22

"

77

4D

120

78

35

23

78

4E

121

79

36

24

79

4F

122

7A

37

25

80

50

123

7B

38

26

&

81

51

124

7C

39

27

'

82

52

125

7D

40

28

83

53

126

7E

127

7F

41

29

84

54

42

2A

85

55

DEL

090.020-CS (JUNE 11)


Page 60

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 61

SECTION 6
QUANTUM LX DATA TABLES

The following table shows the three protocol Address


ranges that may be utilized for reading/writing data to and
from the Quantum LX controller; Frick Addresses, Al-

len-Bradley (AB) Addresses, and Modbus Addresses. This


table also shows the Data Table names, as well as the
page numbers within this manual that the pertinent Data
Tables may be found:

Frick Address Range

AB Address

Modbus Address

Data Table

Pages

1001 - 1061

N10:1 - N10:61

41002 - 41062

Digital Board Values

62 - 63

2000 - 2081

N20:0 - N20:81

42001-43001

Analog Board Values

64 - 65

3000 - 3081

N30:0 - N30:81

43001 - 43082

Calculated Values

66 67

4000 - 4566

N40:0 N45:66

44001 - 44567

Mode Values

68 74

6000 - 6046

N60:00 - N60:46

46001 - 46047

Timer Values

75

7060 - 8558

N100:60 - N115:58

47061 - 48559

Setpoint Values

8910 - 8924

N119:10 - N119:24

48911 - 48925

Commands

8950 - 9007

N119:50 - N120:07

48951 - 49008

DBS Setpoint Values

9100 - 9101

N121:00 N121:01

49101 - 49102

General Setpoint Values

9200 - 9314

N122:00 - N123:14

49201 - 49315

VSD (Vyper) Setpoint Values

76 - 96
97
98 - 99
99
99 - 101

090.020-CS (JUNE 11)


Page 62

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

DIGITAL BOARD VALUES: (Read Only)


Frick
Address

AB
Address

Modbus
Address

Read/Write

Digital
Board #

Channel
#

Module
Type

1001
1002
1003
1004
1005

N10:1
N10:2
N10:3
N10:4
N10:5

41002
41003
41004
41005
41006

R
R
R
R
R

Oil Level/Oil Switch


Capacity Decrease
Capacity Increase
Volume Decrease
Volume Increase

1
1
1
1
1

13
6
5
8
7

Input

1014

N10:14

41015

1015

N10:15

41016

Economizer

11

Liquid Injection

1020

N10:20

41021

Oil Heater

21

Output

1024

N10:24

41025

Hot Gas Bypass

16

Output

1026
1027

N10:26
N10:27

41027
41028

R
R

Compressor Motor Start Signal


Compressor Motor Starter Feed-back

1
1

1
2

Output
Input

1028
1029

N10:28
N10:29

41029
41030

R
R

Oil Pump Start Signal


Oil Pump Feed-back

1
1

3
4

Output
Input

1030

N10:30

41031

Full Flow Pump/Start Signal

None

Description of Data

Output

Output

Output
1032

N10:32

41033

Oil Pump #2 Start Signal

15

1033

N10:33

41034

Oil Pump #2 Feed-back

16

1036
1037
1038
1042
1043
1044
1045

N10:36
N10:37
N10:38
N10:42
N10:43
N10:44
N10:45

41037
41038
41039
41043
41044
41045
41046

R
R
R
R
R
R
R

High Liquid Level Shutdown


Regulator Mode A
Regulator Mode B
Shutdown
Warning
Balance Piston
Panel Heater

1
1
1
1
1
1
1

14
19
20
23
22
12
15

1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062

N10:49
N10:50
N10:51
N10:52
N10:53
N10:54
N10:55
N10:56
N10:57
N10:58
N10:59
N10:60
N10:61
N10:62

41050
41051
41052
41053
41054
41055
41056
41057
41058
41059
41060
41061
41062
41063

R
R
R
R
R
R
R
R
R
R
R
R
R
R

Permissive Start
Ready to Run
Remote Enabled
Recycle Delay
Remote Start/Stop
Remote Load
Remote Unload
Condenser Control Step 1
Condenser Control Step 2
Condenser Control Step 3
Condenser Control Step 4
Power Assist
Dx Circuit #1
Dx Circuit #2

2
2
2
2
2
2
2
2
2
2
2
1
2
2

17
1
2
6
3
4
5
21
22
23
24
24
19
20

Input
Input

Output

Input
Output

Input

Output

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 63

DIGITAL BOARD VALUES: (Read Only, Continued)


1063

N10:63

41064

User Defined Digital Input #1

17

1064
1065
1066
1067
1068
1069
1070

N10:64
N10:65
N10:66
N10:67
N10:68
N10:69
N10:70

41065
41066
41067
41068
41069
41070
41071

R
R
R
R
R
R
R

User Defined Digital Input #2


User Defined Digital Input #3
User Defined Digital Input #4
User Defined Digital Input #5
User Defined Digital Input #6
User Defined Digital Input #7
User Defined Digital Input #8

1
2
2
2
2
2
2

18
9
10
11
12
13
14

1083

N10:83

41084

User Defined Digital Output #1

1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097

N10:84
N10:85
N10:86
N10:87
N10:88
N10:89
N10:90
N10:91
N10:92
N10:93
N10:94
N10:95
N10:96
N10:97

41085
41086
41087
41088
41089
41090
41091
41092
41093
41094
41095
41096
41097
41098

R
R
R
R
R
R
R
R
R
R
R
R
R
R

User Defined Digital Output #2


User Defined Digital Output #3
User Defined Digital Output #4
User Defined Digital Output #5
User Defined Digital Output #6
User Defined Digital Output #7
User Defined Digital Output #8
User Defined Digital Output #9
User Defined Digital Output #10
Main Oil Injection
Liquid Level Increase
Liquid Level Decrease
PLC Interlock
High VI Liquid Injection

2
2
None
None
None
None
None
None
None
None
None
None
None
1

8
18
0
0
0
0
0
0
0
0
0
0
0
10

Input
Input

Output

090.020-CS (JUNE 11)


Page 64

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

ANALOG BOARD VALUES:


Frick
Address

AB
Address

Modbus
Address

Read/Write

Analog
Board #

Channel
#

Module
Type

2001
2002
2003
2004
2005

N20:1
N20:2
N20:3
N20:4
N20:5

42002
42003
42004
42005
42006

R
R
R
R
R

Volume Slide Position


Suction Pressure
Discharge Pressure
Oil Pressure (Compressor)
Main Oil Injection Pressure

1
1
1
1
2

15
9
8
6
15

Input

2007

N20:7

42008

Filter Pressure

Input

2009
2010
2011
2012
2013
2014

N20:9
N20:10
N20:11
N20:12
N20:13
N20:14

42010
42011
42012
42013
42014
42015

R
R
R
R
R
R

Balance Piston Pressure


System Discharge Pressure
Suction Temperature
Discharge Temperature
Oil Temperature (Compressor)
Oil Separator Temperature

1
1
1
1
1
1

10
11
1
2
3
4

Input

2016
2017

N20:16
N20:17

42017
42018

R
R

Process/Brine Temperature Leaving


Process/Brine Temperature Entering

1
2

5
4

Input

2026
2027

N20:26
N20:27

42027
42028

R
R

Remote Control Setpoint


Motor Current

1
1

12
16

2028

N20:28

42029

RPM (NOTE: RPM values are NOT multiplied by 10 in Allen-Bradley and MODBUS
protocols)

16

2029

N20:29

42030

KW Monitoring

None

2031
2032
2033
2034
2035
2036
2037
2038
2039
2040
2041
2051
2052
2053
2054
2055
2056
2057

N20:31
N20:32
N20:33
N20:34
N20:35
N20:36
N20:37
N20:38
N20:39
N20:40
N20:41
N20:51
N20:52
N20:53
N20:54
N20:55
N20:56
N20:57

42032
42033
42034
42035
42036
42037
42038
42039
42040
42041
42042
42052
42053
42054
42055
42056
42057
42058

R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R

User Defined Analog Input #1


User Defined Analog Input #2
User Defined Analog Input #3
User Defined Analog Input #4
User Defined Analog Input #5
User Defined Analog Input #6
User Defined Analog Input #7
User Defined Analog Input #8
User Defined Analog Input #9
User Defined Analog Input #10
User Defined Analog Input #11
PID #1
PID #2
PID #3
PID #4
PID #5
PID #6
PID #7

2
2
2
2
2
2
2
2
2
2
1
1
1
None
None
None
None
None

5
6
7
8
9
10
11
12
13
14
24
1
2
0
0
0
0
0

2058

N20:58

42059

PID #8

None

Description of Data

Input

Input

Output

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 65

ANALOG BOARD VALUES: (Continued)


Frick
Address

AB
Address

Modbus
Address

Read/Write

Description of Data

Analog
Board #

Channel
#

2059
2060
2061
2062
2063
2064
2065
2066
2067
2068
2069
2070
2071
2072
2073
2074
2075
2076
2077
2078
2079
2080
2081
2082
2083
2084
2085
2086
2087
2088
2089
2090
2091
2092

N20:59
N20:60
N20:61
N20:62
N20:63
N20:64
N20:65
N20:66
N20:67
N20:68
N20:69
N20:70
N20:71
N20:72
N20:73
N20:74
N20:75
N20:76
N20:77
N20:78
N20:79
N20:80
N20:81
N20:82
N20:83
N20:84
N20:85
N20:86
N20:87
N20:88
N20:89
N20:90
N20:91
N20:91

42060
42061
42062
42063
42064
42065
42066
42067
42068
42069
42070
42071
42072
42073
42074
42075
42076
42077
42078
42079
42080
42081
42082
42083
42084
42085
42086
42087
42088
42089
42090
42091
42092
42093

R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R

Analog Output #1
Analog Output #2
Analog Output #3
Analog Output #4
Analog Output #5
Analog Output #6
Analog Output #7
Analog Output #8
Manifold Pressure
Remote Capacity Position
Compressor VFD
Liquid Level
Compressor Vibration - Suction
Compressor Vibration - Discharge
Motor Vibration - Shaft Side
Motor Vibration - Opposite Shaft Side
Condenser Analog Step #1
Condenser Analog Step #2
Motor Temperature - Shaft Side
Motor Temperature Opposite Shaft Side
Motor Stator #1 Temperature
Motor Stator #2 Temperature
Motor Stator #3 Temperature
Superheat Output #1
Superheat Output #2
Superheat Output #3
Analog output #10
Analog output #10
Analog output #11
Analog output #12
Analog output #13
Analog output #14
Analog output #15
Analog output #16

1
None
None
None
None
None
None
None
2
1
2
None
1
1
1
1
1
1
None
None
1
1
1
None
None
None
None
None
None
None
None
None
None
None

3
0
0
0
0
0
0
0
3
13
3
0
17
18
19
20
5
6
0
0
21
22
23
0
0
0
0
0
0
0
0
0
0
0

Module
Type

Output

Input
Output

Input

Output

Input

Output

090.020-CS (JUNE 11)


Page 66

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

CALCULATED VALUES:
Frick
Address

AB
Address

Modbus
Address

Read/Write

Analog
Board #

3000
3006

N30:0
N30:6

43001
43007

R
R

Calculated Capacity
Filter Differential Pressure

Percent (%)
Pressure (Magnitude)

3008

N30:8

43009

System Compression Ratio

Percent (%)

3018

N30:18

43019

Current Runtime

3019

N30:19

43020

Suction Superheat

3020

N30:20

43021

Discharge Superheat

3021

N30:21

43022

Percent of Full Load Amps

Description of Data

Channel
#

Module
Type

Hours
Temperature (Magnitude)
Percent (%)

3033

N30:33

43034

Volume High End

3034

N30:34

43035

Volume Current Value

3035

N30:35

43036

Volume Low End

3036

N30:36

43037

Capacity High End

3037

N30:37

43038

Capacity Current Value

3038

N30:38

43039

Capacity Low End

3039

N30:39

43040

Calculated Volume Ratio

3058

N30:58

43059

Calculated Volume Ratio (Suction)

3059

N30:59

43060

Calculated Volume Ration (Economizer)

3060

N30:60

43061

Current Regulation Value

3061

N30:61

43062

Current Regulation Setpoint

Volts

Real

Real
Pressure

3062

N30:62

43063

Estimated Kilowatts

kW

3063

N30:63

43064

Panel Temperature

Temperature

3070

N30:70

43071

Safety #1 Message (Most Recent)

3071

N30:71

43072

Safety #2 Message

3072

N30:72

43073

Safety #3 Message

3073

N30:73

43074

Safety #4 Message

3074

N30:74

43075

Safety #5 Message

3075

N30:75

43076

Safety #6 Message

3076

N30:76

43077

Safety #7 Message

3077

N30:77

43078

Safety #8 Message

3078

N30:78

43079

Safety #9 Message

3079

N30:79

43080

Safety #10 Message

3080

N30:80

43081

Total Run Time (Thousands)

3081

N30:81

43082

Total Run Time (Units)

3102

N31:02

43103

Coalescer Filter Differential

Note
1

Integer

Note
2

Real

Pressure (Magnitude)

Note 1: Refer to the chart of WARNING/SHUTDOWN MESSAGE CODES on pages 116-121 to determine which message
is being displayed.
Note 2: To calculate the Total Run Time, use the following equation:
Total Run Time (Thousands) x 1000 + Total Run Time (Units) = Total Run Time

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 67

MODE VALUES:
Frick
Address

4000

AB
Address

N40:0

Modbus
Address

44001

Read/
Write

Description of Data

Value Code

Compressor Status

0 = Off
1 = Running
20 = Starting
30 = Stopping
31 = Stopping - High Capacity
32 = Stopping Pumpdown
33 = Stopping Cool Down Period

4001

N40:1

44002

Pump Type

0 = No Pump
1 = Full Time
2 = Cycling
3 = Demand
4 = Shaft Auxiliary
5 = Shaft

4002

N40:2

44003

Prelube

0 = Not in Prelube
1 = In Prelube

4003

N40:3

44004

Postlube

0 = Not in Postlube
1 = In Postlube

4004

N40:4

44005

Shutdown

0 = No Shutdowns
1 = Shutdown

4005

N40:5

44006

Warning

0 = No Warning
1 = Warning

4006

N40:6

44007

Recycle Delay Time

0 = Not In Recycle Delay


1 = In Recycle Delay

Compressor mode

0 = Manual
1 = Automatic
2 = Remote -- Communications
3 = Remote -- IO
5 = Remote Sequencing
6 = Manual -- Browser

4007

N40:7

44008

4008

N40:8

44009

Capacity Mode

0 = Manual
1 = Automatic
2 = Remote -- Communications
3 = Remote -- IO
4 = Remote -- 4-20 Input
5 = Remote Sequencing
6 = Manual -- Browser

4009

N40:9

44010

Volume Mode

0 = Manual
1 = Automatic

090.020-CS (JUNE 11)


Page 68

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

MODE VALUES: (Continued)


Frick
Address

4010

4014

AB
Address

N40:10

Modbus
Address

44011

Read/
Write

Description of Data

Compressor Type

0 = RWF
1 = RWBII
2 = RXB
3 = RXF 12-50
4 = RXF 58-101
5 = RDB 4-step
6 = RDB 3-step
7 = GSV II
8 = GST
9 = GSB 3-step
10 = YLC
11 = SC
12 = York S7
13 = York S5
14 = Other Manuf.
15 = Other Manuf (Mycom)
16 = Other Manuf (Kobe)
17 = Recip-0
18 = Recip-1
19 = Recip-2
20 = Recip-3
0 = Regulation 1
1 = Regulation 2
2 = Regulation 3
3 = Regulation 4

N40:14

44015

Regulation Mode

4015

N40:15

44016

Regulation Mode 1 Direction

4016

N40:16

44017

Regulation Mode 2 Direction

4017

N40:17

44018

Regulation Mode 3 Direction

4018

N40:18

44019

Regulation Mode 4 Direction

4019

N40:19

44020

Value Code

Compressor/Drive Type

0 = Forward
1 = Backward
0 = Screw Comp. with Constant Electric Drive
1 = Screw Compressor with VFD Drive
2 = Screw Compressor with Engine Drive
3 = Screw Compressor with Turbine Drive
4 = Screw Compressor with DBS
5 = Screw Compressor with Vyper
6 =Screw Compressor with Vyper (4-20mA)

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 69

MODE VALUES: (Continued)


Frick
Address

4022

AB
Modbus
Address Address

N40:22

44023

Read/
Write

Description of Data

Load Inhibit / Force Unload

Value Code
0 = None
1 = Inhibit-Motor Current
2 = Inhibit-Low Suction Regulation 1
3 = Inhibit-Low Suction Regulation 2
4 = Inhibit-Low Suction Regulation 3
5 = Inhibit-Low Suction Regulation 4
6 = Inhibit-High Discharge Temperature
7 = Inhibit-High Discharge Pressure Mode 1
8 = Inhibit-High Discharge Pressure Mode 2
9 = Inhibit-High Suction Pressure
10 = Inhibit-Low Oil Flow
11 = Inhibit-Separator Velocity
12 = Inhibit-Low RPMs
13 = Inhibit-High Manifold Pressure
14 = Inhibit-Regulation Mode 1
15 = Inhibit-Regulation Mode 2
16 = Inhibit-Regulation Mode 3
17 = Inhibit-Regulation Mode 4
18 = Inhibit-Starting
19 = Inhibit-Capacity Pulldown
20 = Inhibit-At Maximum Load
21 = Inhibit-Vyper Converter Heatsink Temperature
22 = Inhibit-Vyper Ambient Temperature
23 = Inhibit-Harmonic Filter Baseplate Temperature
24 = Inhibit-Vyper Baseplate Temperature
25 = Inhibit-Vyper Phase A Baseplate Temperature
26 = Inhibit-Vyper Phase B Baseplate Temperature
27 = Inhibit-Vyper Phase C Baseplate Temperature
28 = Inhibit - Low Proc. Leaving Temp.
29 = Inhibit Low Engine JW Temperature
30 = Inhibit Maximum Capacity Position
31 = Inhibit Minimum Capacity Position
50 = Force Unload-Volume Increase
51 = Force Unload-Motor Current
52 = Force Unload-Low Suction Regulation 1
53 = Force Unload-Low Suction Regulation 2
54 = Force Unload-Low Suction Regulation 3
55 = Force Unload-Low Suction Regulation 4
56 = Force Unload-Regulation Mode 1
57 = Force Unload-Regulation Mode 2
58 = Force Unload-Regulation Mode 3
59 = Force Unload-Regulation Mode 4
60 = Force Unload-High Discharge Temperature
61 = Force Unload-High Discharge Pressure Mode 1
62 = Force Unload-High Discharge Pressure Mode 2
63 = Force Unload-High Suction Pressure
64 = Force Unload-Low Oil Flow
65 = Force Unload-Separator Velocity
66 = Force Unload-Low RPMs
67 = Force Unload-High Manifold Pressure
68 = Force Unload-Stopping
69 = Force Unload-Vyper Converter Heatsink Temp.
70 = Force Unload-Vyper Ambient Temp.
71 = Force Unload-Harmonic Filter Baseplate Temp.
72 = Force Unload-Vyper Baseplate Temp.
73 = Force Unload-Vyper Phase A Baseplate Temp.
74 = Force Unload-Vyper Phase B Baseplate Temp.
75 = Force Unload-Vyper Phase C Baseplate Temp.
76 = Unload - Low Proc. Leaving Temp.
77 = Force Unload Maximum Capacity Position
78 Force Unload Minimum Capacity Position

090.020-CS (JUNE 11)


Page 70

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

MODE VALUES: (Continued)


Frick
Address
4027

AB
Modbus
Address Address
N40:27

44028

Read/
Write
R

Description of Data

Value Code

Condenser Enabled

0 = Disabled
1 = Running
2 = Always

4070

N40:70

44071

Compressor Start Status

0 = Ready
1 = Start Inhibit In Shutdown
2 = Start Inhibit In Recycle Delay
3 = Start Inhibit High Discharge Temperature
4 = Start Inhibit High Oil Temperature
5 = Start Inhibit Low Separator Temperature
6 = Start Inhibit Slide Valve Too High
7 = Start Inhibit Still In Prelube
8 = Start Inhibit High Suction Pressure
9 = Start Inhibit High Suction/Discharge Differential
10 = Start Inhibit Permissive Start
11 = Start Inhibit Digital Auxiliaries
12 = Power Fail Restart
13 = Start Inhibit Low Oil Pressure
14 = Running
15 = Start Inhibit In Discharge Pressure Blowdown

4071

N40:71

44072

Capacity Status

0 = Idle
1 = Load
2 = Unload

4072

N40:72

44073

Volume Status

0 = Idle
1 = Increase
2 = Decrease

(Local

0 = English
1 = French
2 = Chinese
3 = Portuguese
Display
4 = Polish
5 = Chinese
6 = Spanish
7 = Russian
8 = Italian

4073

N40:73

44074

Language
Only)

4074

N40:74

44075

Temperature Units (Local 0 = Celsius


Display Only)
1 = Fahrenheit

4075

N40:75

44076

0 = Kpaa
1 = Bar
Pressure Units (Local Dis- 2 = BarA
play Only)
3 = PSIA
4 = PSIG/hg
5 = kpaG

4077

N40:77

44078

Regulation Mode 1

4078

N40:78

44079

Regulation Mode 2

4079

N40:79

44080

Regulation Mode 3

4080

N40:80

44081

Regulation Mode 4

4081

N40:81

44082

Sequencing Control Enable

4199

N41:99

44200

0 = Idle
Manual Capacity Load/Un1 = Load
load
2 = Unload

0 = Disabled
1 = Enabled

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 71

MODE VALUES: (Continued)


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

Value Code

4200

N42:00

44201

Alarm Silence

0 = Off
1 = On

4201

N42:01

44202

Manual Compressor Action

-1 = Idle
0 = Stop
1 = Run

4234

N42:34

44235

Refrigerant

1 = R11
2 = R113
3 = R114
4 = R1150
5 = R12
6 = R1270
7 = R13
8 = R134a
9 = R13b1
10 = R14
11 = R142b
12 = R170
13 = R218
14 = R22
15 = R23
16 = R290
17 = R401a
18 = R402a

4237

N42:37

44238

Oil Pump Status

0 = Off
1 = Running

4239

N42:39

44240

PID 1 Control

0 = Disabled
1 = Running
2 = Always

4242

N42:42

44243

PID 2 Control

0 = Disabled
1 = Running
2 = Always

4245

N42:45

44246

PID 3 Control

0 = Disabled
1 = Running
2 = Always

4248

N42:48

44249

PID 4 Control

0 = Disabled
1 = Running
2 = Always

4251

N42:51

44252

PID 5 Control

0 = Disabled
1 = Running
2 = Always

4254

N42:54

44255

PID 6 Control

0 = Disabled
1 = Running
2 = Always

19 = R404a
20 = R410a
21 = R50
22 = R500
23 = R502
24 = R503
25 = R507
26 = R508
27 = R508b
28 = R600
29 = R600a
30 = R717
31 = R718
32 = R728
33 = R729
34 = R744
35 = R771
50 = User Defined

090.020-CS (JUNE 11)


Page 72

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

MODE VALUES: (Continued)


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

Value Code

4257

N42:57

44258

PID 7 Control

0 = Disabled
1 = Running
2 = Always

4260

N42:60

44261

PID 8 Control

0 = Disabled
1 = Running
2 = Always

4383

N43:83

44384

Sequencing Sys. 1 Comp 1 Comp Mode

4384

N43:84

44385

Sequencing Sys. 1 Comp 2 Comp Mode

4385

N43:85

44386

Sequencing Sys. 1 Comp 3 Comp Mode

4386

N43:86

44387

Sequencing Sys. 1 Comp 4 Comp Mode

4387

N43:87

44388

Sequencing Sys. 1 Comp 5 Comp Mode

4388

N43:88

44389

Sequencing Sys. 1 Comp 6 Comp Mode

4389

N43:89

44390

Sequencing Sys. 1 Comp 7 Comp Mode

4390

N43:90

44391

Sequencing Sys. 1 Comp 8 Comp Mode

4391

N43:91

44392

Sequencing Sys. 1 Comp 1 Capacity Mode

4392

N43:92

44393

Sequencing Sys. 1 Comp 2 Capacity Mode

4393

N43:93

44394

Sequencing Sys. 1 Comp 3 Capacity Mode

4394

N43:94

44395

Sequencing Sys. 1 Comp 4 Capacity Mode

4395

N43:95

44396

Sequencing Sys. 1 Comp 5 Capacity Mode

4396

N43:96

44397

Sequencing Sys. 1 Comp 6 Capacity Mode

4397

N43:97

44398

Sequencing Sys. 1 Comp 7 Capacity Mode

4398

N43:98

44399

Sequencing Sys. 1 Comp 8 Capacity Mode

4407

N44:07

44408

Sequencing Enable - System 1

4417

N44:17

44418

Sequencing - Sys 1 Comp 1 Comp Status

4418

N44:18

44419

Sequencing - Sys 1 Comp 2 Comp Status

4419

N44:19

44420

Sequencing - Sys 1 Comp 3 Comp Status

4420

N44:20

44421

Sequencing - Sys 1 Comp 4 Comp Status

4421

N44:21

44422

Sequencing - Sys 1 Comp 5 Comp Status

4422

N44:22

44423

Sequencing - Sys 1 Comp 6 Comp Status

4423

N44:23

44424

Sequencing - Sys 1 Comp 7 Comp Status

4424

N44:24

44425

Sequencing - Sys 1 Comp 8 Comp Status

4433

N44:33

44434

Sequencing Sys. 2 Comp 1 Comp Mode

4434

N44:34

44435

Sequencing Sys. 2 Comp 2 Comp Mode

4435

N44:35

44436

Sequencing Sys. 2 Comp 3 Comp Mode

4436

N44:36

44437

Sequencing Sys. 2 Comp 4 Comp Mode

4437

N44:37

44438

Sequencing Sys. 2 Comp 5 Comp Mode

4438

N44:38

44439

Sequencing Sys. 2 Comp 6 Comp Mode

4439

N44:39

44440

Sequencing Sys. 2 Comp 7 Comp Mode

4440

N44:40

44441

Sequencing Sys. 2 Comp 8 Comp Mode

0 = Manual
1 = Automatic
2 = Remote -- Communications
3 = Remote -- IO
5 = Remote -- Sequencing

0 = Manual
1 = Automatic
2 = Remote -- Communications
3 = Remote -- IO
4 = Remote -- 4-20 Input
5 = Remote -- Sequencing

0 = Disabled
1 = Enabled

0 = Off
1 = Running
20 = Starting
30 = Stopping
31 = Stopping - High Capacity
32 = Stopping - Pumpdown

0 = Manual
1 = Automatic
2 = Remote -- Communications
3 = Remote -- IO
5 = Remote -- Sequencing

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 73

MODE VALUES: (Continued)


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

4441

N44:41

44442

Sequencing Sys. 2 Comp 1 Capacity Mode

4442

N44:42

44443

Sequencing Sys. 2 Comp 2 Capacity Mode

4443

N44:43

44444

Sequencing Sys. 2 Comp 3 Capacity Mode

4444

N44:44

44445

Sequencing Sys. 2 Comp 4 Capacity Mode

4445

N44:45

44446

Sequencing Sys. 2 Comp 5 Capacity Mode

4446

N44:46

44447

Sequencing Sys. 2 Comp 6 Capacity Mode

4447

N44:47

44448

Sequencing Sys. 2 Comp 7 Capacity Mode

4448

N44:48

44449

Sequencing Sys. 2 Comp 8 Capacity Mode

4457

N44:57

44458

Sequencing Enable - System 2

4467

N44:67

44468

Sequencing Sys. 2 Comp 1 Comp Status

4468

N44:68

44469

Sequencing Sys. 2 Comp 2 Comp Status

4469

N44:69

44470

Sequencing Sys. 2 Comp 3 Comp Status

4470

N44:70

44471

Sequencing Sys. 2 Comp 4 Comp Status

4471

N44:71

44472

Sequencing Sys. 2 Comp 5 Comp Status

4472

N44:72

44473

Sequencing Sys. 2 Comp 6 Comp Status

4473

N44:73

44474

Sequencing Sys. 2 Comp 7 Comp Status

4474

N44:74

44475

Sequencing - Sys 2 Comp 8 Comp Status

4483

N44:83

44484

Sequencing Sys. 3 Comp 1 Comp Mode

4484

N44:84

44485

Sequencing Sys. 3 Comp 2 Comp Mode

4485

N44:85

44486

Sequencing Sys. 3 Comp 3 Comp Mode

4486

N44:86

44487

Sequencing Sys. 3 Comp 4 Comp Mode

4487

N44:87

44488

Sequencing Sys. 3 Comp 5 Comp Mode

4488

N44:88

44489

Sequencing Sys. 3 Comp 6 Comp Mode

4489

N44:89

44490

Sequencing Sys. 3 Comp 7 Comp Mode

4490

N44:90

44491

Sequencing Sys. 3 Comp 8 Comp Mode

4491

N44:91

44492

Sequencing Sys. 3 Comp 1 Capacity Mode

4492

N44:92

44493

Sequencing Sys. 3 Comp 2 Capacity Mode

4493

N44:93

44494

Sequencing Sys. 3 Comp 3 Capacity Mode

4494

N44:94

44495

Sequencing Sys. 3 Comp 4 Capacity Mode

4495

N44:95

44496

Sequencing Sys. 3 Comp 5 Capacity Mode

4496

N44:96

44497

Sequencing Sys. 3 Comp 6 Capacity Mode

4497

N44:97

44498

Sequencing Sys. 3 Comp 7 Capacity Mode

4498

N44:98

44499

Sequencing Sys. 3 Comp 8 Capacity Mode

4507

N45:07

44508

Sequencing Enable - System 3

Value Code

0 = Manual
1 = Automatic
2 = Remote - Communications
3 = Remote - IO
4 = Remote - 4-20 Input
5 = Remote Sequencing

0 = Disabled
1 = Enabled

0 = Off
1 = Running
20 = Starting
30 = Stopping
31 = Stopping - High Capacity
32 = Stopping - Pumpdown

0 = Manual
1 = Automatic
2 = Remote - Communications
3 = Remote - IO
5 = Remote Sequencing

0 = Manual
1 = Automatic
2 = Remote - Communications
3 = Remote - IO
4 = Remote - 4-20 Input
5 = Remote Sequencing

0 = Disabled
1 = Enabled

090.020-CS (JUNE 11)


Page 74

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

MODE VALUES: (Continued)


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

4517

N45:17

44518

Sequencing Sys. 3 Comp 1 Comp Status

4518

N45:18

44519

Sequencing Sys. 3 Comp 2 Comp Status

4519

N45:19

44520

Sequencing Sys. 3 Comp 3 Comp Status

4520

N45:20

44521

Sequencing Sys. 3 Comp 4 Comp Status

Value Code

0 = Off
1 = Running
20 = Starting
30 = Stopping
31 = Stopping - High Capacity
32 = Stopping - Pumpdown

4521

N45:21

44522

Sequencing Sys. 3 Comp 5 Comp Status

4522

N45:22

44523

Sequencing Sys. 3 Comp 6 Comp Status

4523

N45:23

44524

Sequencing Sys. 3 Comp 7 Comp Status

4524

N45:24

44525

Sequencing Sys. 3 Comp 8 Comp Status

4533

N45:33

44534

Oil Pump Mode

0 = Manual
1 = Automatic

4534

N45:34

44535

Screen Saver

0 = Disabled
1 = Enabled

4539

N45:39

44540

Starter Alarms

4540

N45:40

44541

Starter Trips

4547

N45:47

44548

Input Module Capacity Mode Selection

0 = Disabled
1 = Enabled

4548

N45:48

44549

Permissive Start Enable

0 = Disabled
1 = Starting
2 = Always

4549

N45:49

44550

PLC Interlock Enable

0 = Disabled
1 = Enabled

4550

N45:50

44551

Remote Enable Output

0 = Disabled
1 = Compressor Mode: Remote I/O
2 = Compressor Mode: Remote I/O
and Capacity Mode: Remote I/O
3 = Compressor Mode: Remote I/O
and Capacity Mode: Remote 4-20

4551

N45:51

44552

Oil Log Mode

0 = Disabled
1 = Enabled

4566

N45:66

44567

Communications Unit Flag

0 = Celsius / PSIA
1 = Panel Units

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

TIMER VALUES: (Read Only)


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

6000

N60:00

46001

Pre-Lube Timer

6001

N60:01

46002

Post-lube Timer

6002

N60:02

46003

Stopping Unload Timer

6003

N60:03

46004

Volume Control Timer

6004

N60:04

46005

Capacity Control Timer

6006

N60:06

46007

Capacity Load Time

6007

N60:07

46008

Capacity Unload Time

6008

N60:08

46009

General 10 Second Timer

6009

N60:09

46010

Step Load Inhibit Time

6010

N60:10

46011

Step Unload Delay Time

6011

N60:11

46012

Drive Output Timer

6012

N60:12

46013

Autocycle Start Timer

6013

N60:13

46014

Autocycle Stop Timer

6014

N60:14

46015

Condenser Step Timer

6015

N60:15

46016

Balance Piston Ignore

6016

N60:16

46017

Stopping Pumpdown Timer

6017

N60:17

46018

Liquid Injection Timer

6018

N60:18

46019

Liquid Level Timer

6019

N60:19

46020

Oil Injection Timer

6020

N60:20

46021

Starting Load Inhibit Timer

6021

N60:21

46022

Capacity Pulldown Timer

6022

N60:22

46023

General 60 Second Timer

6023

N60:23

46024

Recycle Delay Timer

6024

N60:24

46025

Oil Charging Timer

6025

N60:25

46026

Differential Pressure OK Timer

6026

N60:26

46027

Slide to Zero Timer

6027

N60:27

46028

General 1 Second Timer

6028

N60:28

46029

Capacity/Volume Calibration Timer

6029

N60:29

46030

Dual Pump Transition Timer

6030

N60:30

46031

Power Assist Timer

6031

N60:31

46032

Power Fail Restart Timer

6032

N60:32

46033

PLC Interlock Timer

6036

N60:36

46037

Motor Amps Ignore

6037

N60:37

46038

Remote I/O Start Stop

6038

N60:38

46039

Vyper Standby Timer

6039

N60:39

46040

Drive Force Unload Timer

6040

N60:40

46041

Vyper Clear Standby Timer

6041

N60:41

46042

Min Slide Valve Timer

6042

N60:42

46043

Force Unload Step Timer

6043

N60:43

46044

Safety Unload Delay Timer

6044

N60:44

46045

Step Volume Timer

6045

N60:45

46046

Sequencing Disable Timer

6046

N60:46

46047

Shutdown Unload Timer

090.020-CS (JUNE 11)


Page 75

090.020-CS (JUNE 11)


Page 76

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES:
Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

7060

N100:60

47061

R/W

Screen Saver Delay Setpoint

7061

N100:61

47062

R/W

Atmospheric Pressure

7100

N101:00

47101

R/W

K Factor

7102

N101:02

47103

R/W

Unload Delay When Stopping

Units
Minutes
Pressure (Magnitude)
Real
Seconds

7103

N101:03

47104

R/W

Hot Gas On When Below

7104

N101:04

47105

R/W

False Running Compressor Input Delay

Seconds

7120

N101:20

47121

R/W

Power Assist

Seconds

7121

N101:21

47122

R/W

Power Failure Restart Delay

Minutes

7123

N101:23

47124

R/W

Panel Heater On Value

7124

N101:24

47125

R/W

Panel Heater Off Value

7125

N101:25

47126

R/W

Permissive Start Shutdown Delay

7126

N101:26

47127

R/W

PLC Interlock Delay

7150

N101:50

47151

R/W

Regulation Mode 1 Setpoint


Regulation Mode 1 High Dead Band

7152

N101:52

47153

R/W

7153

N101:53

47154

R/W

Regulation Mode 1 Low Dead Band

7154

N101:54

47155

R/W

Regulation Mode 1 High Proportional Band

Percent (%)

Temperature
Seconds
Pressure

Pressure (Magnitude)

7155

N101:55

47156

R/W

Regulation Mode 1 Low Proportional Band

7156

N101:56

47157

R/W

Regulation Mode 1 High Cycle Time

7157

N101:57

47158

R/W

Regulation Mode 1 Low Cycle Time

7158

N101:58

47159

R/W

Regulation Mode 1 Auto Cycle Start

7159

N101:59

47160

R/W

Regulation Mode 1 Auto Cycle Start Delay

Minutes

7160

N101:60

47161

R/W

Regulation Mode 1 Auto Cycle Stop

Pressure
Minutes

7161

N101:61

47162

R/W

Regulation Mode 1 Auto Cycle Stop Delay

7162

N101:62

47163

R/W

Regulation Mode 1 Load Inhibit

7163

N101:63

47164

R/W

Regulation Mode 1 Force Unload

7164

N101:64

47165

R/W

Regulation Mode 1 Shutdown

Seconds
Pressure

Pressure

7165

N101:65

47166

R/W

Regulation Mode 1 Warning

7166

N101:66

47167

R/W

Regulation Mode 1 Shutdown Delay

7167

N101:67

47168

R/W

Regulation Mode 1 Warning Delay

7168

N101:68

47169

R/W

Low Suction Pressure Shutdown Mode 1

7169

N101:69

47170

R/W

Low Suction Pressure Shutdown Mode 1 Delay

Seconds

7170

N101:70

47171

R/W

Low Suction Pressure Warning Mode 1

Pressure
Seconds

Seconds
Pressure

7171

N101:71

47172

R/W

Low Suction Pressure Warning Mode 1 Delay

7172

N101:72

47173

R/W

Low Suction Pressure Mode 1 Load Inhibit

7173

N101:73

47174

R/W

Low Suction Pressure Mode 1 Force Unload

7176

N101:76

47177

R/W

Mode 1 Prop Band

Pressure

7177

N101:77

47178

R/W

Mode 1 Integration Time

Seconds

7200

N102:00

47201

R/W

Regulation Mode 2 Setpoint

7202

N102:02

47203

R/W

Regulation Mode 2 High Dead Band

7203

N102:03

47204

R/W

Regulation Mode 2 Low Dead Band

Pressure

Temperature
Temperature (Magnitude)

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 77

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

7204

N102:04

47205

R/W

Regulation Mode 2 High Proportional Band

7205

N102:05

47206

R/W

Regulation Mode 2 Low Proportional Band

7206

N102:06

47207

R/W

Regulation Mode 2 High Cycle Time

7207

N102:07

47208

R/W

Regulation Mode 2 Low Cycle Time

7208

N102:08

47209

R/W

Regulation Mode 2 Auto Cycle Start

7209

N102:09

47210

R/W

Regulation Mode 2 Auto Cycle Start Delay

7210

N102:10

47211

R/W

Regulation Mode 2 Auto Cycle Stop

7211

N102:11

47212

R/W

Regulation Mode 2 Auto Cycle Stop Delay

7212

N102:12

47213

R/W

Regulation Mode 2 Load Inhibit

7213

N102:13

47214

R/W

Regulation Mode 2 Force Unload

7214

N102:14

47215

R/W

Regulation Mode 2 Shutdown

Units
Temperature (Magnitude)
Seconds
Temperature
Minutes
Temperature
Minutes

Temperature

7215

N102:15

47216

R/W

Regulation Mode 2 Warning

7216

N102:16

47217

R/W

Regulation Mode 2 Shutdown Delay

7217

N102:17

47218

R/W

Regulation Mode 2 Warning Delay

7218

N102:18

47219

R/W

Low Suction Pressure Shutdown Mode 2

7219

N102:19

47220

R/W

Low Suction Pressure Shutdown Mode 2 Delay

Seconds

7220

N102:20

47221

R/W

Low Suction Pressure Warning Mode 2

Pressure
Seconds

Seconds
Pressure

7221

N102:21

47222

R/W

Low Suction Pressure Warning Mode 2 Delay

7222

N102:22

47223

R/W

Low Suction Pressure Mode 2 Load Inhibit

7223

N102:23

47224

R/W

Low Suction Pressure Mode 2 Force Unload

7226

N102:26

47227

R/W

Mode 2 Prop Band

Pressure

7227

N102:27

47228

R/W

Mode 2 Integration Time

Seconds

7250

N102:50

47251

R/W

Regulation Mode 3 Setpoint

Pressure

7252

N102:52

47253

R/W

Regulation Mode 3 High Dead Band

7253

N102:53

47254

R/W

Regulation Mode 3 Low Dead Band

7254

N102:54

47255

R/W

Regulation Mode 3 High Proportional Band

Pressure

Pressure (Magnitude)

7255

N102:55

47256

R/W

Regulation Mode 3 Low Proportional Band

7256

N102:56

47257

R/W

Regulation Mode 3 High Cycle Time

7257

N102:57

47258

R/W

Regulation Mode 3 Low Cycle Time

7258

N102:58

47259

R/W

Regulation Mode 3 Auto Cycle Start

7259

N102:59

47260

R/W

Regulation Mode 3 Auto Cycle Start Delay

Minutes

7260

N102:60

47261

R/W

Regulation Mode 3 Auto Cycle Stop

Pressure
Minutes

7261

N102:61

47262

R/W

Regulation Mode 3 Auto Cycle Stop Delay

7262

N102:62

47263

R/W

Regulation Mode 3 Load Inhibit

7263

N102:63

47264

R/W

Regulation Mode 3 Force Unload

7264

N102:64

47265

R/W

Regulation Mode 3 Shutdown

Seconds
Pressure

Pressure

7265

N102:65

47266

R/W

Regulation Mode 3 Warning

7266

N102:66

47267

R/W

Regulation Mode 3 Shutdown Delay

7267

N102:67

47268

R/W

Regulation Mode 3 Warning Delay

7268

N102:68

47269

R/W

Low Suction Pressure Shutdown Mode 3

Pressure

7269

N102:69

47270

R/W

Low Suction Pressure Shutdown Mode 3 Delay

Seconds

7270

N102:70

47271

R/W

Low Suction Pressure Warning Mode 3

Pressure

7271

N102:71

47272

R/W

Low Suction Pressure Warning Mode 3 Delay

Seconds

Seconds

090.020-CS (JUNE 11)


Page 78

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

Units

7272

N102:72

47273

R/W

Low Suction Pressure Mode 3 Load Inhibit

7273

N102:73

47274

R/W

Low Suction Pressure Mode 3 Force Unload

7276

N102:76

47277

R/W

Mode 3 Prop Band

Pressure

7277

N102:77

47278

R/W

Mode 3 Integration Time

Seconds

7300

N103:00

47301

R/W

Regulation Mode 4 Setpoint

Pressure

7302

N103:02

47303

R/W

Regulation Mode 4 High Dead Band

7303

N103:03

47304

R/W

Regulation Mode 4 Low Dead Band

7304

N103:04

47305

R/W

Regulation Mode 4 High Proportional Band

Pressure

Pressure (Magnitude)

7305

N103:05

47306

R/W

Regulation Mode 4 Low Proportional Band

7306

N103:06

47307

R/W

Regulation Mode 4 High Cycle Time

7307

N103:07

47308

R/W

Regulation Mode 4 Low Cycle Time

7308

N103:08

47309

R/W

Regulation Mode 4 Auto Cycle Start

7309

N103:09

47310

R/W

Regulation Mode 4 Auto Cycle Start Delay

Minutes

7310

N103:10

47311

R/W

Regulation Mode 4 Auto Cycle Stop

Pressure
Minutes

7311

N103:11

47312

R/W

Regulation Mode 4 Auto Cycle Stop Delay

7312

N103:12

47313

R/W

Regulation Mode 4 Load Inhibit

7313

N103:13

47314

R/W

Regulation Mode 4 Force Unload

7314

N103:14

47315

R/W

Regulation Mode 4 Shutdown

Seconds
Pressure

Pressure

7315

N103:15

47316

R/W

Regulation Mode 4 Warning

7316

N103:16

47317

R/W

Regulation Mode 4 Shutdown Delay

7317

N103:17

47318

R/W

Regulation Mode 4 Warning Delay

7318

N103:18

47319

R/W

Low Suction Pressure Shutdown Mode 4

7319

N103:19

47320

R/W

Low Suction Pressure Shutdown Mode 4 Delay

Seconds

7320

N103:20

47321

R/W

Low Suction Pressure Warning Mode 4

Pressure
Seconds

Seconds
Pressure

7321

N103:21

47322

R/W

Low Suction Pressure Warning Mode 4 Delay

7322

N103:22

47323

R/W

Low Suction Pressure Mode 4 Load Inhibit

7323

N103:23

47324

R/W

Low Suction Pressure Mode 4 Force Unload

7326

N103:26

47327

R/W

Mode 4 Prop Band

Pressure

7327

N103:27

47328

R/W

Mode 4 Integration Time

Seconds

7350

N103:50

47351

R/W

High Motor Current Load Inhibit

7351

N103:51

47352

R/W

High Motor Current Force Unload

7352

N103:52

47353

R/W

High Motor Current Shutdown

7353

N103:53

47354

R/W

High Motor Current Warning

7354

N103:54

47355

R/W

High Motor Current Shutdown Delay

7355

N103:55

47356

R/W

High Motor Current Warning Delay

7356

N103:56

47357

R/W

Low Motor Current Shutdown

7357

N103:57

47358

R/W

Low Motor Current Shutdown Delay

7358

N103:58

47359

R/W

Motor Current Confirmed Running

7359

N103:59

47360

R/W

False Running Motor Amps Delay

7360

N103:60

47361

R/W

Starting Motor Amps Ignore Period

7361

N103:61

47362

R/W

Name Plate Motor Amps

7362

N103:62

47363

R/W

Volts

7363

N103:63

47364

R/W

Service Factor

Pressure

Amps

Seconds
Amps
Seconds
Amps
Seconds
Amps
Integer
Real

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 79

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

Units

7364

N103:64

47365

R/W

Horsepower

Integer

7365

N103:65

47366

R/W

Recycle Delay

Minutes

7366

N103:66

47367

R/W

CT Factor

7373

N103:73

47374

R/W

Drive Increase Cycle Time

None
Seconds

7374

N103:74

47375

R/W

Drive Increase Rate Of Change

7375

N103:75

47376

R/W

Drive Idle

7376

N103:76

47377

R/W

Drive Minimum

7377

N103:77

47378

R/W

Drive Maximum

7378

N103:78

47379

R/W

Drive Decrease Cycle Time

7379

N103:79

47380

R/W

Drive Decrease Rate Of Change

7380

N103:80

47381

R/W

Proportional Drive Speed Maximum

Percent (%)

Seconds

7381

N103:81

47382

R/W

Proportional Slide Valve Maximum

7382

N103:82

47383

R/W

Low RPMs Shutdown

7383

N103:83

47384

R/W

Low RPMs Warning

7384

N103:84

47385

R/W

Low RPMs Load Inhibit

7385

N103:85

47386

R/W

Low RPMs Force Unload

7386

N103:86

47387

R/W

Low RPMs Shutdown Delay

7387

N103:87

47388

R/W

Low RPMs Warning Delay

7388

N103:88

47389

R/W

High RPMs Shutdown

7389

N103:89

47390

R/W

High RPMs Warning

7390

N103:90

47391

R/W

High RPMs Shutdown Delay

(NOTE: RPM values are NOT


multiplied by 10 in Allen-Bradley and MODBUS protocols)

Percent (%)

RPM

Seconds
(NOTE: RPM values are NOT
multiplied by 10 in Allen-Bradley and MODBUS protocols)

7391

N103:91

47392

R/W

High RPMs Warning Delay

7392

N103:92

47393

R/W

High Manifold Pressure Load Inhibit

7393

N103:93

47394

R/W

High Manifold Pressure Force Unload

7394

N103:94

47395

R/W

High Manifold Pressure Shutdown

RPM
Seconds

7395

N103:95

47396

R/W

High Manifold Pressure Warning

7396

N103:96

47397

R/W

High Manifold Pressure Shutdown Delay

7397

N103:97

47398

R/W

High Manifold Pressure Warning Delay

7398

N103:98

47399

R/W

RPM Confirmed Running Shutdown Delay


(NOTE: RPM values are NOT
multiplied by 10 in AllenBradley and MODBUS protocols)

7399

N103:99

47400

R/W

RPM Confirmed Running

7400

N104:00

47401

R/W

Highest Capacity Position For Starting

7401

N104:01

47402

R/W

Capacity Slide Stroke

7402

N104:02

47403

R/W

Capacity Decrease Assist Rate

7403

N104:03

47404

R/W

Remote Capacity 4_20 Deadband

7404

N104:04

47405

R/W

Automatic Capacity Mode Minimum Slide Valve Position

7405

N104:05

47406

R/W

Minimum Capacity Pulse Time

7406

N104:06

47407

R/W

Step Force Unload Load Inhibit Period

7407

N104:07

47408

R/W

Starting Load Inhibit Period

7408

N104:08

47409

R/W

Capacity Position For Volume Increase Force Unload

7409

N104:09

47410

R/W

Recip Step Count

7410

N104:10

47411

R/W

Capacity Top End (Calibration)

7411

N104:11

47312

R/W

Capacity Bottom End (Calibration)

7413

N104:13

47414

R/W

Volume Top End

7414

N104:14

47415

R/W

Volume Bottom End

Pressure

Seconds
Minutes
RPM
Percent (%)
Real
Percent (%)

Seconds
Percent (%)
Integer

Real

090.020-CS (JUNE 11)


Page 80

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

7415

N104:15

47416

R/W

Volume Middle

7416

N104:16

47417

R/W

Volume Deadband

7417

N104:17

47418

R/W

Volume Pulse Time

7418

N104:18

47419

R/W

Volume Top End (Calibration)

7419

N104:19

47420

R/W

Volume Bottom End (Calibration)

7423

N104:23

47424

R/W

Drive Proportional Band

7424

N104:24

47425

R/W

Drive Integration Time

7425

N104:25

47426

R/W

Time Schedule Sunday 1st Mode Hour 1

7426

N104:26

47427

R/W

Time Schedule Sunday 1st Mode Minute 1

7427

N104:27

47428

R/W

Time Schedule Sunday 2nd Mode Hour 2

7428

N104:28

47429

R/W

Time Schedule Sunday 2nd Mode Minute 2

7429

N104:29

47430

R/W

Time Schedule Sunday 3rd Mode Hour 1

7430

N104:30

47431

R/W

Time Schedule Sunday 3rd Mode Minute 1

7431

N104:31

47432

R/W

Time Schedule Sunday 4th Mode Hour 2

7432

N104:32

47433

R/W

Time Schedule Sunday 4th Mode Minute 2

7433

N104:33

47434

R/W

Time Schedule Monday 1st Mode Hour 1

7434

N104:34

47435

R/W

Time Schedule Monday 1st Mode Minute 1

7435

N104:35

47436

R/W

Time Schedule Monday 2nd Mode Hour 2

7436

N104:36

47437

R/W

Time Schedule Monday 2nd Mode Minute 2

7437

N104:37

47438

R/W

Time Schedule Monday 3rd Mode Hour 1

7438

N104:38

47439

R/W

Time Schedule Monday 3rd Mode Minute 1

7439

N104:39

47440

R/W

Time Schedule Monday 4th Mode Hour 2

7440

N104:40

47441

R/W

Time Schedule Monday 4th Mode Minute 2

7441

N104:41

47442

R/W

Time Schedule Tuesday 1st Mode Hour 1

7442

N104:42

47443

R/W

Time Schedule Tuesday 1st Mode Minute 1

7443

N104:43

47444

R/W

Time Schedule Tuesday 2nd Mode Hour 2

7444

N104:44

47445

R/W

Time Schedule Tuesday 2nd Mode Minute 2

7445

N104:45

47446

R/W

Time Schedule Tuesday 3rd Mode Hour 1

7446

N104:46

47447

R/W

Time Schedule Tuesday 3rd Mode Minute 1

7447

N104:47

47448

R/W

Time Schedule Tuesday 4th Mode Hour 2

7448

N104:48

47449

R/W

Time Schedule Tuesday 4th Mode Minute 2

7449

N104:49

47450

R/W

Time Schedule Wednesday 1st Mode Hour 1

7450

N104:50

47451

R/W

Time Schedule Wednesday 1st Mode Minute 1

7451

N104:51

47452

R/W

Time Schedule Wednesday 2nd Mode Hour 2

7452

N104:52

47453

R/W

Time Schedule Wednesday 2nd Mode Minute 2

7453

N104:53

47454

R/W

Time Schedule Wednesday 3rd Mode Hour 1

7454

N104:54

47455

R/W

Time Schedule Wednesday 3rd Mode Minute 1


Time Schedule Wednesday 4th Mode Hour 2

7455

N104:55

47456

R/W

7456

N104:56

47457

R/W

Time Schedule Wednesday 4th Mode Minute 2

7457

N104:57

47458

R/W

Time Schedule Thursday 1st Mode Hour 1

7458

N104:58

47459

R/W

Time Schedule Thursday 1st Mode Minute 1

7459

N104:59

47460

R/W

Time Schedule Thursday 2nd Mode Hour 2

7460

N104:60

47461

R/W

Time Schedule Thursday 2nd Mode Minute 2

7461

N104:61

47462

R/W

Time Schedule Thursday 3rd Mode Hour 1

7462

N104:62

47463

R/W

Time Schedule Thursday 3rd Mode Minute 1

7463

N104:63

47464

R/W

Time Schedule Thursday 4th Mode Hour 2

Units

Real

Integer
Seconds

Integer

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 81

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

7464

N104:64

47465

R/W

Time Schedule Thursday 4th Mode Minute 2

7465

N104:65

47466

R/W

Time Schedule Friday 1st Mode Hour 1

7466

N104:66

47467

R/W

Time Schedule Friday 1st Mode Minute 1

7467

N104:67

47468

R/W

Time Schedule Friday 2nd Mode Hour 2

7468

N104:68

47469

R/W

Time Schedule Friday 2nd Mode Minute 2

7469

N104:69

47470

R/W

Time Schedule Friday 3rd Mode Hour 1

7470

N104:70

47471

R/W

Time Schedule Friday 3rd Mode Minute 1

7471

N104:71

47472

R/W

Time Schedule Friday 4th Mode Hour 2

7472

N104:72

47473

R/W

Time Schedule Friday 4th Mode Minute 2

7473

N104:73

47474

R/W

Time Schedule Saturday 1st Mode Hour 1

7474

N104:74

47475

R/W

Time Schedule Saturday 1st Mode Minute 1

7475

N104:75

47476

R/W

Time Schedule Saturday 2nd Mode Hour 2

7476

N104:76

47477

R/W

Time Schedule Saturday 2nd Mode Minute 2

7477

N104:77

47478

R/W

Time Schedule Saturday 3rd Mode Hour 1

7478

N104:78

47479

R/W

Time Schedule Saturday 3rd Mode Minute 1

7479

N104:79

47480

R/W

Time Schedule Saturday 4th Mode Hour 2

7480

N104:80

47481

R/W

Time Schedule Saturday 4th Mode Minute 2

7486

N104:86

47487

R/W

Skip Frequency 1 Bottom

7487

N104:87

47488

R/W

Skip Frequency 1 Top

7488

N104:88

47489

R/W

Skip Frequency 2 Bottom

7489

N104:89

47490

R/W

Skip Frequency 2 Top

7490

N104:90

47491

R/W

Skip Frequency 3 Bottom

7491

N104:91

47492

R/W

Skip Frequency 3 Top

Units

Integer

Percent (%)

7492

N104:92

47493

R/W

Skip Frequency 4 Bottom

7493

N104:93

47494

R/W

Skip Frequency 4 Top

7494

N104:94

47495

R/W

Skip Frequency 5 Bottom

7495

N104:95

47496

R/W

Skip Frequency 5 Top

7500

N105:00

47501

R/W

Demand/Cycling On

7501

N105:01

47502

R/W

Demand/Cycling Off

7502

N105:02

47503

R/W

Lube Time When Starting

Seconds

7503

N105:03

47504

R/W

Post Lube When Stopping

Minutes

7510

N105:10

47511

R/W

High Suction Pressure Load Inhibit

7511

N105:11

47512

R/W

High Suction Pressure Force Unload

7512

N105:12

47513

R/W

High Suction Pressure Shutdown

7513

N105:13

47514

R/W

High Suction Pressure Warning

7514

N105:14

47515

R/W

High Suction Pressure Shutdown Delay

7515

N105:15

47516

R/W

High Suction Pressure Warning Delay

7520

N105:20

47521

R/W

High Discharge Temperature Shutdown

7521

N105:21

47522

R/W

High Discharge Temperature Warning

7522

N105:22

47523

R/W

High Discharge Temperature Shutdown Delay

7523

N105:23

47524

R/W

High Discharge Temperature Warning Delay

7524

N105:24

47525

R/W

High Discharge Temperature Load Inhibit

7525

N105:25

47526

R/W

High Discharge Temperature Force Unload

7526

N105:26

47527

R/W

High Discharge Pressure Inhibit Load Mode 1

7527

N105:27

47528

R/W

High Discharge Pressure Force Unload Mode 1

7528

N105:28

47529

R/W

High Discharge Pressure Warning Mode 1

Pressure (Magnitude)

Pressure

Seconds
Temperature
Seconds
Temperature

Pressure (Positive)

090.020-CS (JUNE 11)


Page 82

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

7529

N105:29

47530

R/W

High Discharge Pressure Shutdown Mode 1

7530

N105:30

47531

R/W

High Discharge Pressure Warning Mode 1 Delay

7531

N105:31

47532

R/W

High Discharge Pressure Shutdown Mode 1 Delay

7532

N105:32

47533

R/W

High Discharge Pressure Inhibit Load Mode 2

7533

N105:33

47534

R/W

High Discharge Pressure Force Unload Mode 2

7534

N105:34

47535

R/W

High Discharge Pressure Warning Mode 2

7535

N105:35

47536

R/W

High Discharge Pressure Shutdown Mode 2

7536

N105:36

47537

R/W

High Discharge Pressure Warning Mode 2 Delay

7537

N105:37

47538

R/W

High Discharge Pressure Shutdown Mode 2 Delay

7538

N105:38

47539

R/W

Starting Differential Pressure

7550

N105:50

47551

R/W

Oil Heater Off When Above

7551

N105:51

47552

R/W

Oil Injection On When Above

Units
Pressure (Positive)
Seconds
Pressure (Positive)

Seconds
Pressure (Magnitude)

Temperature

7552

N105:52

47553

R/W

Oil Injection On Delay

7553

N105:53

47554

R/W

Missing Oil Pressure Warning Offset

Pressure (Magnitude)

7554

N105:54

47555

R/W

Missing Oil Pressure Warning Delay

Seconds

7555

N105:55

47556

R/W

Missing Oil Pressure Shutdown Offset

7556

N105:56

47557

R/W

Missing Oil Pressure Shutdown Delay A

7557

N105:57

47558

R/W

Missing Oil Pressure Shutdown Delay B

7558

N105:58

47559

R/W

Insufficient Oil Pressure Safety Offset

7559

N105:59

47560

R/W

Insufficient Oil Pressure Shutdown Capacity Value

7560

N105:60

47561

R/W

Insufficient Oil Pressure Shutdown Delay

7561

N105:61

47562

R/W

Insufficient Oil Pressure Load Inhibit Capacity Value

7562

N105:62

47563

R/W

Insufficient Oil Pressure Force Unload Capacity Value

7563

N105:63

47564

R/W

High Oil Temperature Shutdown

7564

N105:64

47565

R/W

High Oil Temperature Warning

7565

N105:65

47566

R/W

High Oil Temperature Shutdown Delay

7566

N105:66

47567

R/W

High Oil Temperature Warning Delay

7567

N105:67

47568

R/W

Low Oil Temperature Shutdown

7568

N105:68

47569

R/W

Low Oil Temperature Warning

7569

N105:69

47570

R/W

Low Oil Temperature Shutdown Delay

7570

N105:70

47571

R/W

Low Oil Temperature Warning Delay

7571

N105:71

47572

R/W

Low Oil Injection Pressure Shutdown

7572

N105:72

47573

R/W

Low Oil Injection Pressure Shutdown Delay

7573

N105:73

47574

R/W

Low Oil Level Shutdown Delay

7574

N105:74

47575

R/W

Low Oil Pressure Shutdown

7575

N105:75

47576

R/W

Low Oil Pressure Warning

7576

N105:76

47577

R/W

Low Oil Pressure Shutdown Delay

7577

N105:77

47578

R/W

Low Oil Pressure Warning Delay

7578

N105:78

47579

R/W

Low Oil Pressure Shutdown 2

7579

N105:79

47580

R/W

Low Oil Pressure Shutdown Delay 2

7580

N105:80

47581

R/W

Low Separator Temperature Shutdown

7581

N105:81

47582

R/W

Low Separator Temperature Warning

Seconds

Pressure (Magnitude)
Seconds
Pressure (Magnitude)
Percent (%)
Seconds
Percent (%)
Temperature
Seconds
Temperature
Seconds
Pressure (Magnitude)
Seconds
Pressure (Magnitude)
Seconds
Pressure (Magnitude)
Seconds
Temperature

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 83

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

Units

7582

N105:82

47583

R/W

Low Separator Temperature Shutdown Delay

7583

N105:83

47584

R/W

Low Separator Temperature Warning Delay

7584

N105:84

47585

R/W

Dual Pump Transition Time

7585

N105:85

47586

R/W

Oil Log Shutdown Delay

7586

N105:86

47587

R/W

Dual Pump Transition Time Due To Low Oil Pressure

7587

N105:87

47588

R/W

Separator Velocity Reference

7588

N105:88

47589

R/W

Separator Velocity Ratio

7600

N106:00

47601

R/W

High Filter Shutdown

7601

N106:01

47602

R/W

High Filter Shutdown Delay

7602

N106:02

47603

R/W

High Filter Warning

7603

N106:03

47604

R/W

High Filter Warning Delay

Minutes

7604

N106:04

47605

R/W

Condenser High Pressure Override

Pressure

7605

N106:05

47606

R/W

Condenser High Pressure Override Delay

7606

N106:06

47607

R/W

Condenser Proportional Band

7607

N106:07

47608

R/W

Condenser Integration Time

7608

N106:08

47609

R/W

Condenser High Limit

7609

N106:09

47610

R/W

Condenser Low Limit

7610

N106:10

47611

R/W

Condenser Control Setpoint

7611

N106:11

47612

R/W

Condenser High Dead Band

7612

N106:12

47613

R/W

Condenser Low Dead Band

7613

N106:13

47614

R/W

Condenser High Step Delay

7614

N106:14

47615

R/W

Condenser Low Step Delay

7615

N106:15

47616

R/W

Condenser Order Step 1

7616

N106:16

47617

R/W

Condenser Order Step 2

7617

N106:17

47618

R/W

Condenser Order Step 3

7618

N106:18

47619

R/W

Condenser Order Step 4

7620

N106:20

47621

R/W

Balance Piston On

7621

N106:21

47622

R/W

Balance Piston Off

7622

N106:22

47623

R/W

Balance Piston Ignore Period

7623

N106:23

47624

R/W

Balance Piston Safety Delay

7635

N106:35

47636

R/W

Liquid Slug Warning Setpoint

7636

N106:36

47637

R/W

Liquid Slug Shutdown Setpoint

7640

N106:40

47641

R/W

Liquid Level Setpoint

7641

N106:41

47642

R/W

Liquid Level Deadband

7642

N106:42

47643

R/W

Liquid Level Proportional Band

7643

N106:43

47644

R/W

High Liquid Level Delay

7650

N106:50

47651

R/W

Liquid Injection On When Above

7651

N106:51

47652

R/W

Liquid Injection On Delay

7660

N106:60

47661

R/W

Dx Circuit 1 OnWhenAbove

Seconds

Real

Pressure (Magnitude)
Minutes
Pressure (Magnitude)

Seconds
Pressure (Magnitude)
Seconds
Percent (%)
Pressure
Pressure (Magnitude)
Seconds

Integer

Percent (%)
Minutes

Temp. (Magnitude)

None
Seconds
Temperature
Seconds
Percent (%)

090.020-CS (JUNE 11)


Page 84

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

Units

7661

N106:61

47662

R/W

Dx Circuit 1Off When Below

7662

N106:62

47663

R/W

Dx Circuit 2 On When Above

7663

N106:63

47664

R/W

Dx Circuit 2 Off When Below

7664

N106:64

47665

7670

N106:70

47671

R/W

Economizer On When Above

7671

N106:71

47672

R/W

Economizer Off When Below

7672

N106:72

47673

R/W

Economizer Over Ride

Pressure (Magnitude)

7673

N106:73

47674

R/W

Economizer Port Value

Real

7674

N106:74

47675

R/W

Economizer Fixed Pressure

7680

N106:80

47681

R/W

Pump Down Setpoint

Pressure

7681

N106:81

47682

R/W

Pump Down Time When Stopping

Minutes

7690

N106:90

47691

R/W

Capacity Pulldown Step

7691

N106:91

47692

R/W

Capacity Pulldown Step Time

7700

N107:00

47701

R/W

Auxiliary Input 1 Delay

7701

N107:01

47702

R/W

Auxiliary Input 2 Delay

7702

N107:02

47703

R/W

Auxiliary Input 3 Delay

Dewpoint Temperature of Discharge

7703

N107:03

47704

R/W

Auxiliary Input 4 Delay

7704

N107:04

47705

R/W

Auxiliary Input 5 Delay

7705

N107:05

47706

R/W

Auxiliary Input 6 Delay

7706

N107:06

47707

R/W

Auxiliary Input 7 Delay

7707

N107:07

47708

R/W

Auxiliary Input 8 Delay

7708

N107:08

47709

R/W

Auxiliary Input 9 Delay

7709

N107:09

47710

R/W

Auxiliary Input 10 Delay

7710

N107:10

47711

R/W

Auxiliary Input 11 Delay

7711

N107:11

47712

R/W

Auxiliary Input 12 Delay

7712

N107:12

47713

R/W

Auxiliary Input 13 Delay

7713

N107:13

47714

R/W

Auxiliary Input 14 Delay

7714

N107:14

47715

R/W

Auxiliary Input 15 Delay

7715

N107:15

47716

R/W

Auxiliary Input 16 Delay

7716

N107:16

47717

R/W

Auxiliary Input 17 Delay

7717

N107:17

47718

R/W

Auxiliary Input 18 Delay

7718

N107:18

47719

R/W

Auxiliary Input 19 Delay

Percent (%)
Temperature

Percent (%)

Pressure (Positive)

Percent (%)
Seconds

Seconds

7719

N107:19

47720

R/W

Auxiliary Input 20 Delay

7730

N107:30

47731

R/W

Auxiliary Analog 1 High Shutdown

Pressure

7731

N107:31

47732

R/W

Auxiliary Analog 1 High Shutdown Delay

Seconds

7732

N107:32

47733

R/W

Auxiliary Analog 1 High Warning

Pressure

7733

N107:33

47734

R/W

Auxiliary Analog 1 High Warning Delay

Seconds

7734

N107:34

47735

R/W

Auxiliary Analog 1 Low Shutdown

Pressure

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 85

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

Units

7735

N107:35

47736

R/W

Auxiliary Analog 1 Low Shutdown Delay

Seconds

7736

N107:36

47737

R/W

Auxiliary Analog 1 Low Warning

Pressure

7737

N107:37

47738

R/W

Auxiliary Analog 1 Low Warning Delay

Seconds

7740

N107:40

47741

R/W

Auxiliary Analog 2 High Shutdown

Pressure

7741

N107:41

47742

R/W

Auxiliary Analog 2 High Shutdown Delay

Seconds

7742

N107:42

47743

R/W

Auxiliary Analog 2 High Warning

Pressure

7743

N107:43

47744

R/W

Auxiliary Analog 2 High Warning Delay

Seconds

7744

N107:44

47745

R/W

Auxiliary Analog 2 Low Shutdown

Pressure

7745

N107:45

47746

R/W

Auxiliary Analog 2 Low Shutdown Delay

Seconds

7746

N107:46

47747

R/W

Auxiliary Analog 2 Low Warning

Pressure

7747

N107:47

47748

R/W

Auxiliary Analog 2 Low Warning Delay

Seconds

7750

N107:50

47751

R/W

Auxiliary Analog 3 High Shutdown

Pressure

7751

N107:51

47752

R/W

Auxiliary Analog 3 High Shutdown Delay

Seconds

7752

N107:52

47753

R/W

Auxiliary Analog 3 High Warning

Pressure

7753

N107:53

47754

R/W

Auxiliary Analog 3 High Warning Delay

Seconds

7754

N107:54

47755

R/W

Auxiliary Analog 3 Low Shutdown

Pressure

7755

N107:55

47756

R/W

Auxiliary Analog 3 Low Shutdown Delay

Seconds

7756

N107:56

47757

R/W

Auxiliary Analog 3 Low Warning

Pressure

7757

N107:57

47758

R/W

Auxiliary Analog 3 Low Warning Delay

Seconds

7760

N107:60

47761

R/W

Auxiliary Analog 4 High Shutdown

Pressure

7761

N107:61

47762

R/W

Auxiliary Analog 4 High Shutdown Delay

Seconds

7762

N107:62

47763

R/W

Auxiliary Analog 4 High Warning

Pressure

7763

N107:63

47764

R/W

Auxiliary Analog 4 High Warning Delay

Seconds

7764

N107:64

47765

R/W

Auxiliary Analog 4 Low Shutdown

Pressure

7765

N107:65

47766

R/W

Auxiliary Analog 4 Low Shutdown Delay

Seconds

7766

N107:66

47767

R/W

Auxiliary Analog 4 Low Warning

Pressure

7767

N107:67

47768

R/W

Auxiliary Analog 4 Low Warning Delay

Seconds

7770

N107:70

47771

R/W

Auxiliary Analog 5 High Shutdown

Pressure

7771

N107:71

47772

R/W

Auxiliary Analog 5 High Shutdown Delay

Seconds

7772

N107:72

47773

R/W

Auxiliary Analog 5 High Warning

Pressure

7773

N107:73

47774

R/W

Auxiliary Analog 5 High Warning Delay

Seconds

7774

N107:74

47775

R/W

Auxiliary Analog 5 Low Shutdown

Pressure

7775

N107:75

47776

R/W

Auxiliary Analog 5 Low Shutdown Delay

Seconds

7776

N107:76

47777

R/W

Auxiliary Analog 5 Low Warning

Pressure

7777

N107:77

47778

R/W

Auxiliary Analog 5 Low Warning Delay

Seconds

7780

N107:80

47781

R/W

Auxiliary Analog 6 High Shutdown

Pressure

7781

N107:81

47782

R/W

Auxiliary Analog 6 High Shutdown Delay

Seconds

7782

N107:82

47783

R/W

Auxiliary Analog 6 High Warning

Pressure

090.020-CS (JUNE 11)


Page 86

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

Units

7783

N107:83

47784

R/W

Auxiliary Analog 6 High Warning Delay

Seconds

7784

N107:84

47785

R/W

Auxiliary Analog 6 Low Shutdown

Pressure

7785

N107:85

47776

R/W

Auxiliary Analog 6 Low Shutdown Delay

Seconds

7786

N107:86

47787

R/W

Auxiliary Analog 6 Low Warning

Pressure

7787

N107:87

47788

R/W

Auxiliary Analog 6 Low Warning Delay

Seconds

7790

N107:90

47791

R/W

Auxiliary Analog 7 High Shutdown

Pressure

7791

N107:91

47792

R/W

Auxiliary Analog 7 High Shutdown Delay

Seconds

7792

N107:92

47793

R/W

Auxiliary Analog 7 High Warning

Pressure

7793

N107:93

47794

R/W

Auxiliary Analog 7 High Warning Delay

Seconds

7794

N107:94

47795

R/W

Auxiliary Analog 7 Low Shutdown

Pressure

7795

N107:95

47796

R/W

Auxiliary Analog 7 Low Shutdown Delay

Seconds

7796

N107:96

47797

R/W

Auxiliary Analog 7 Low Warning

Pressure

7797

N107:97

47798

R/W

Auxiliary Analog 7 Low Warning Delay

Seconds

7800

N108:00

47801

R/W

Auxiliary Analog 8 High Shutdown

Pressure

7801

N108:01

47802

R/W

Auxiliary Analog 8 High Shutdown Delay

Seconds

7802

N108:02

47803

R/W

Auxiliary Analog 8 High Warning

Pressure

7803

N108:03

47804

R/W

Auxiliary Analog 8 High Warning Delay

Seconds

7804

N108:04

47805

R/W

Auxiliary Analog 8 Low Shutdown

Pressure

7805

N108:05

47806

R/W

Auxiliary Analog 8 Low Shutdown Delay

Seconds

7806

N108:06

47807

R/W

Auxiliary Analog 8 Low Warning

Pressure

7807

N108:07

47808

R/W

Auxiliary Analog 8 Low Warning Delay

Seconds

7810

N108:10

47811

R/W

Auxiliary Analog 9 High Shutdown

Pressure

7811

N108:11

47812

R/W

Auxiliary Analog 9 High Shutdown Delay

Seconds

7812

N108:12

47813

R/W

Auxiliary Analog 9 High Warning

Pressure

7813

N108:13

47814

R/W

Auxiliary Analog 9 High Warning Delay

Seconds

7814

N108:14

47815

R/W

Auxiliary Analog 9 Low Shutdown

Pressure

47816

R/W

7815

N108:15

Auxiliary Analog 9 Low Shutdown Delay

Seconds

7816

N108:16

47817

R/W

Auxiliary Analog 9 Low Warning

Pressure

7817

N108:17

47818

R/W

Auxiliary Analog 9 Low Warning Delay

Seconds

7820

N108:20

47821

R/W

Auxiliary Analog 10 High Shutdown

Pressure

7821

N108:21

47822

R/W

Auxiliary Analog 10 High Shutdown Delay

Seconds

7822

N108:22

47823

R/W

Auxiliary Analog 10 High Warning

Pressure

7823

N108:23

47824

R/W

Auxiliary Analog 10 High Warning Delay

Seconds

7824

N108:24

47825

R/W

Auxiliary Analog 10 Low Shutdown

Pressure

7825

N108:25

47826

R/W

Auxiliary Analog 10 Low Shutdown Delay

Seconds

7826

N108:26

47827

R/W

Auxiliary Analog 10 Low Warning

Pressure

7827

N108:27

47828

R/W

Auxiliary Analog 10 Low Warning Delay

Seconds

7830

N108:30

47831

R/W

Auxiliary Analog 11 High Shutdown

Pressure

7831

N108:31

47832

R/W

Auxiliary Analog 11 High Shutdown Delay

Seconds

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 87

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

Units

7832

N108:32

47833

R/W

Auxiliary Analog 11 High Warning

Pressure

7833

N108:33

47834

R/W

Auxiliary Analog 11 High Warning Delay

Seconds

7834

N108:34

47835

R/W

Auxiliary Analog 11 Low Shutdown

Pressure

7835

N108:35

47836

R/W

Auxiliary Analog 11 Low Shutdown Delay

Seconds

7836

N108:36

47837

R/W

Auxiliary Analog 11 Low Warning

Pressure

7837

N108:37

47838

R/W

Auxiliary Analog 11 Low Warning Delay

Seconds

7840

N108:40

47841

R/W

Auxiliary Analog 12 High Shutdown

Pressure

7841

N108:41

47842

R/W

Auxiliary Analog 12 High Shutdown Delay

Seconds

7842

N108:42

47843

R/W

Auxiliary Analog 12 High Warning

Pressure

7843

N108:43

47844

R/W

Auxiliary Analog 12 High Warning Delay

Seconds

7844

N108:44

47845

R/W

Auxiliary Analog 12 Low Shutdown

Pressure

7845

N108:45

47846

R/W

Auxiliary Analog 12 Low Shutdown Delay

Seconds

7846

N108:46

47847

R/W

Auxiliary Analog 12 Low Warning

Pressure

7847

N108:47

47848

R/W

Auxiliary Analog 12 Low Warning Delay

Seconds

7850

N108:50

47851

R/W

Auxiliary Analog 13 High Shutdown

Pressure

7851

N108:51

47852

R/W

Auxiliary Analog 13 High Shutdown Delay

Seconds

7852

N108:52

47853

R/W

Auxiliary Analog 13 High Warning

Pressure

7853

N108:53

47854

R/W

Auxiliary Analog 13 High Warning Delay

Seconds

7854

N108:54

47855

R/W

Auxiliary Analog 13 Low Shutdown

Pressure

7855

N108:55

47856

R/W

Auxiliary Analog 13 Low Shutdown Delay

Seconds

7856

N108:56

47857

R/W

Auxiliary Analog 13 Low Warning

Pressure

7857

N108:57

47858

R/W

Auxiliary Analog 13 Low Warning Delay

Seconds

7860

N108:60

47861

R/W

Auxiliary Analog 14 High Shutdown

Pressure

7861

N108:61

47862

R/W

Auxiliary Analog 14 High Shutdown Delay

Seconds

7862

N108:62

47863

R/W

Auxiliary Analog 14 High Warning

Pressure

7863

N108:63

47864

R/W

Auxiliary Analog 14 High Warning Delay

Seconds

7864

N108:64

47865

R/W

Auxiliary Analog 14 Low Shutdown

Pressure

7865

N108:65

47866

R/W

Auxiliary Analog 14 Low Shutdown Delay

Seconds

7866

N108:66

47867

R/W

Auxiliary Analog 14 Low Warning

Pressure

7867

N108:67

47868

R/W

Auxiliary Analog 14 Low Warning Delay

Seconds

7870

N108:70

47871

R/W

Auxiliary Analog 15 High Shutdown

Pressure

7871

N108:71

47872

R/W

Auxiliary Analog 15 High Shutdown Delay

Seconds

7872

N108:72

47873

R/W

Auxiliary Analog 15 High Warning

Pressure

7873

N108:73

47874

R/W

Auxiliary Analog 15 High Warning Delay

Seconds

7874

N108:74

47875

R/W

Auxiliary Analog 15 Low Shutdown

Pressure

7875

N108:75

47876

R/W

Auxiliary Analog 15 Low Shutdown Delay

Seconds

7876

N108:76

47877

R/W

Auxiliary Analog 15 Low Warning

Pressure

7877

N108:77

47878

R/W

Auxiliary Analog 15 Low Warning Delay

Seconds

7880

N108:80

47881

R/W

Auxiliary Analog 16 High Shutdown

Pressure

7881

N108:81

47882

R/W

Auxiliary Analog 16 High Shutdown Delay

Seconds

090.020-CS (JUNE 11)


Page 88

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

Units

7882

N108:82

47883

R/W

Auxiliary Analog 16 High Warning

Pressure

7883

N108:83

47884

R/W

Auxiliary Analog 16 High Warning Delay

Seconds

7884

N108:84

47885

R/W

Auxiliary Analog 16 Low Shutdown

Pressure

7885

N108:85

47886

R/W

Auxiliary Analog 16 Low Shutdown Delay

Seconds

7886

N108:86

47887

R/W

Auxiliary Analog 16 Low Warning

Pressure

7887

N108:87

47888

R/W

Auxiliary Analog 16 Low Warning Delay

Seconds

7890

N108:90

47891

R/W

Auxiliary Analog 17 High Shutdown

Pressure

7891

N108:91

47892

R/W

Auxiliary Analog 17 High Shutdown Delay

Seconds

7892

N108:92

47893

R/W

Auxiliary Analog 17 High Warning

Pressure

7893

N108:93

47894

R/W

Auxiliary Analog 17 High Warning Delay

Seconds

7894

N108:94

47895

R/W

Auxiliary Analog 17 Low Shutdown

Pressure

7895

N108:95

47896

R/W

Auxiliary Analog 17 Low Shutdown Delay

Seconds

7896

N108:96

47897

R/W

Auxiliary Analog 17 Low Warning

Pressure

7897

N108:97

47898

R/W

Auxiliary Analog 17 Low Warning Delay

Seconds

7900

N109:00

47901

R/W

Auxiliary Analog 18 High Shutdown

Pressure

7901

N109:01

47902

R/W

Auxiliary Analog 18 High Shutdown Delay

Seconds

7902

N109:02

47903

R/W

Auxiliary Analog 18 High Warning

Pressure

7903

N109:03

47904

R/W

Auxiliary Analog 18 High Warning Delay

Seconds

7904

N109:04

47905

R/W

Auxiliary Analog 18 Low Shutdown

Pressure

7905

N109:05

47906

R/W

Auxiliary Analog 18 Low Shutdown Delay

Seconds

7906

N109:06

47907

R/W

Auxiliary Analog 18 Low Warning

Pressure

7907

N109:07

47908

R/W

Auxiliary Analog 18 Low Warning Delay

Seconds

7910

N109:10

47911

R/W

Auxiliary Analog 19 High Shutdown

Pressure

7911

N109:11

47912

R/W

Auxiliary Analog 19 High Shutdown Delay

Seconds

7912

N109:12

47913

R/W

Auxiliary Analog 19 High Warning

Pressure

7913

N109:13

47914

R/W

Auxiliary Analog 19 High Warning Delay

Seconds

7914

N109:14

47915

R/W

Auxiliary Analog 19 Low Shutdown

Pressure

7915

N109:15

47916

R/W

Auxiliary Analog 19 Low Shutdown Delay

Seconds

7916

N109:16

47917

R/W

Auxiliary Analog 19 Low Warning

Pressure

7917

N109:17

47918

R/W

Auxiliary Analog 19 Low Warning Delay

Seconds

7920

N109:20

47921

R/W

Auxiliary Analog 20 High Shutdown

Pressure

7921

N109:21

47922

R/W

Auxiliary Analog 20 High Shutdown Delay

Seconds

7922

N109:22

47923

R/W

Auxiliary Analog 20 High Warning

Pressure

7923

N109:23

47924

R/W

Auxiliary Analog 20 High Warning Delay

Seconds

7924

N109:24

47925

R/W

Auxiliary Analog 20 Low Shutdown

Pressure

7925

N109:25

47926

R/W

Auxiliary Analog 20 Low Shutdown Delay

Seconds

7926

N109:26

47927

R/W

Auxiliary Analog 20 Low Warning

Pressure

7927

N109:27

47928

R/W

Auxiliary Analog 20 Low Warning Delay

Seconds

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 89

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

7930

N109:30

47931

R/W

High Entering Process Temperature Shutdown

7931

N109:31

47932

R/W

High Entering Process Temperature Warning

7932

N109:32

47933

R/W

High Entering Process Temperature Shutdown Delay

7933

N109:33

47934

R/W

High Entering Process Temperature Warning Delay

7934

N109:34

47935

R/W

Low Entering Process Temperature Shutdown

7935

N109:35

47936

R/W

Low Entering Process Temperature Warning

7936

N109:36

47937

R/W

Low Entering Process Temperature Shutdown Delay

7937

N109:37

47938

R/W

Low Entering Process Temperature Warning Delay

8000

N110:00

48001

R/W

PID 1 Setpoint

8001

N110:01

48002

R/W

PID 1 Deadband

8002

N110:02

48003

R/W

PID 1 Proportional Band

8003

N110:03

48004

R/W

PID 1 Integral Gain

8004

N110:04

48005

R/W

PID 1 Derivative Gain

8005

N110:05

48006

R/W

PID 1 High Limit

8006

N110:06

48007

R/W

PID 1 Low Limit

8007

N110:07

48008

R/W

PID 1 When Running Off Value

8008

N110:08

48009

R/W

PID 2 Setpoint

8009

N110:09

48010

R/W

PID 2 Deadband

8010

N110:10

48011

R/W

PID 2 Proportional Band

8011

N110:11

48012

R/W

PID 2 Integral Gain

8012

N110:12

48013

R/W

PID 2 Derivative Gain

8013

N110:13

48014

R/W

PID 2 High Limit

8014

N110:14

48015

R/W

PID 2 Low Limit

8015

N110:15

48016

R/W

PID 2 When Running Off Value

8016

N110:16

48017

R/W

PID 3 Setpoint

8017

N110:17

48018

R/W

PID 3 Deadband

8018

N110:18

48019

R/W

PID 3 Proportional Band

8019

N110:19

48020

R/W

PID 3 Integral Gain

8020

N110:20

48021

R/W

PID 3 Derivative Gain

8021

N110:21

48022

R/W

PID 3 High Limit

8022

N110:22

48023

R/W

PID 3 Low Limit

8023

N110:23

48024

R/W

PID 3 When Running Off Value

8024

N110:24

48025

R/W

PID 4 Setpoint

8025

N110:25

48026

R/W

PID 4 Deadband

8026

N110:26

48027

R/W

PID 4 Proportional Band

8027

N110:27

48028

R/W

PID 4 Integral Gain

8028

N110:28

48029

R/W

PID 4 Derivative Gain

8029

N110:29

48030

R/W

PID 4 High Limit

8030

N110:30

48031

R/W

PID 4 Low Limit

8031

N110:31

48032

R/W

PID 4 When Running Off Value

Units
Temperature
Seconds
Temperature
Seconds

Temperature
None
Temp. (Magnitude)
Real

Percent (%)

None

Real

Percent (%)

None

Real

Percent (%)

None

Real

Percent (%)

090.020-CS (JUNE 11)


Page 90

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

8032

N110:32

48033

R/W

PID 5 Setpoint

8033

N110:33

48034

R/W

PID 5 Deadband

8034

N110:34

48035

R/W

PID 5 Proportional Band

8035

N110:35

48036

R/W

PID 5 Integral Gain

8036

N110:36

48037

R/W

PID 5 Derivative Gain

8037

N110:37

48038

R/W

PID 5 High Limit

8038

N110:38

48039

R/W

PID 5 Low Limit

8039

N110:39

48040

R/W

PID 5 When Running Off Value

8040

N110:40

48041

R/W

PID 6 Setpoint

8041

N110:41

48042

R/W

PID 6 Deadband

8042

N110:42

48043

R/W

PID 6 Proportional Band

8043

N110:43

48044

R/W

PID 6 Integral Gain

8044

N110:44

48045

R/W

PID 6 Derivative Gain

8045

N110:45

48046

R/W

PID 6 High Limit

8046

N110:46

48047

R/W

PID 6 Low Limit

8047

N110:47

48048

R/W

PID 6 When Running Off Value

8048

N110:48

48049

R/W

PID 7 Setpoint

8049

N110:49

48050

R/W

PID 7 Deadband

8050

N110:50

48051

R/W

PID 7 Proportional Band

8051

N110:51

48052

R/W

PID 7 Integral Gain

8052

N110:52

48053

R/W

PID 7 Derivative Gain

8053

N110:53

48054

R/W

PID 7 High Limit

8054

N110:54

48055

R/W

PID 7 Low Limit

8055

N110:55

48056

R/W

PID 7 When Running Off Value

8056

N110:56

48057

R/W

PID 8 Setpoint

8057

N110:57

48058

R/W

PID 8 Deadband

8058

N110:58

48059

R/W

PID 8 Proportional Band

8059

N110:59

48060

R/W

PID 8 Integral Gain

8060

N110:60

48061

R/W

PID 8 Derivative Gain

8061

N110:61

48062

R/W

PID 8 High Limit

8062

N110:62

48063

R/W

PID 8 Low Limit

8063

N110:63

48064

R/W

PID 8 When Running Off Value

8070

N110:70

48071

R/W

High Compressor Vibration Warning - Suction

8071

N110:71

48072

R/W

High Compressor Vibration Warning Delay - Suction

8072

N110:72

48073

R/W

High Compressor Vibration Warning - Discharge

8073

N110:73

48074

R/W

High Compressor Vibration Warning Delay - Discharge

8074

N110:74

48075

R/W

High Compressor Vibration Shutdown - Suction

8075

N110:75

48076

R/W

High Compressor Vibration Shutdown Delay - Suction

8076

N110:76

48077

R/W

High Compressor Vibration Shutdown - Discharge

8077

N110:77

48078

R/W

High Compressor Vibration Shutdown Delay - Discharge

8078

N110:78

48079

R/W

High Motor Vibration Warning - Shaft Side

8079

N110:79

48080

R/W

High Motor Vibration Warning Delay - Shaft Side

Units

None

Real
Percent (%)
Percent (%)

None

Real

Percent (%)

None

Real

Percent (%)

None

Real

Percent (%)

Vibration (Fg)
Seconds
Vibration (Fg)
Seconds
Vibration (Fg)
Seconds
Vibration (Fg)
Seconds
Vibration (Fg)
Seconds

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 91

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

8080

N110:80

48081

R/W

High Motor Vibration Warning - Opposite Shaft Side

8081

N110:81

48082

R/W

High Motor Vibration Warning Delay - Opposite Shaft Side

8082

N110:82

48083

R/W

High Motor Vibration Shutdown - Shaft Side

8083

N110:83

48084

R/W

High Motor Vibration Shutdown Delay - Shaft Side

8084

N110:84

48085

R/W

High Motor Vibration Shutdown - Opposite Shaft Side

8085

N110:85

48086

R/W

High Motor Vibration Shutdown Delay - Opposite Shaft Side

8086

N110:86

48087

R/W

High Motor Temp. Warning - Shaft Side

8087

N110:87

48088

R/W

High Motor Temp. Warning Delay - Shaft Side

8088

N110:88

48089

R/W

High Motor Temp. Warning - Opposite Shaft Side

8089

N110:89

48090

R/W

High Motor Temp. Warning Delay - Opposite Shaft Side

8090

N110:90

48091

R/W

High Motor Temp. Shutdown - Shaft Side

8091

N110:91

48092

R/W

High Motor Temp. Shutdown Delay - Shaft Side

8092

N110:92

48093

R/W

High Motor Temp. Shutdown Opposite Shaft Side

8093

N110:93

48094

R/W

High Motor Temp. Shutdown Delay Opposite Shaft Side

8140

N111:40

48141

R/W

High Motor Stator #1 Temperature Warning

8141

N111:41

48142

R/W

High Motor Stator #1 Temperature Warning Delay

8142

N111:42

48143

R/W

High Motor Stator #1 Temperature Shutdown

8143

N111:43

48144

R/W

High Motor Stator #1 Temperature Shutdown Delay

8144

N111:44

48145

R/W

High Motor Stator #2 Temperature Warning

8145

N111:45

48146

R/W

High Motor Stator #2 Temperature Warning Delay

8146

N111:46

48147

R/W

High Motor Stator #2 Temperature Shutdown

8147

N111:47

48148

R/W

High Motor Stator #2 Temperature Shutdown Delay

8148

N111:48

48149

R/W

High Motor Stator #3 Temperature Warning

8149

N111:49

48150

R/W

High Motor Stator #3 Temperature Warning Delay

8150

N111:50

48151

R/W

High Motor Stator #3 Temperature Shutdown

8151

N111:51

48152

R/W

High Motor Stator #3 Temperature Shutdown Delay

8201

N112:01

48202

R/W

Oil Analysis Service Interval

8202

N112:02

48203

R/W

Change Filters Service Interval

8203

N112:03

48204

R/W

Clean Oil Strainers Service Interval

8204

N112:04

48205

R/W

Clean Liquid Strainers Service Interval

8205

N112:05

48206

R/W

Clean Coalescers Service Interval

8206

N112:06

48207

R/W

Clean Suction Screen Service Interval

8207

N112:07

48208

R/W

Vibration Analysis Service Interval

8208

N112:08

48209

R/W

Check Coupling Service Interval

8209

N112:09

48210

R/W

Grease Motor Service Interval

8210

N112:10

48211

R/W

User Defined #1 Service Interval

8211

N112:11

48212

R/W

User Defined #2 Service Interval

8212

N112:12

48213

R/W

User Defined #3 Service Interval

8213

N112:13

48214

R/W

User Defined #4 Service Interval

8214

N112:14

48215

R/W

User Defined #5 Service Interval

8215

N112:15

48216

R/W

User Defined #6 Service Interval

8216

N112:16

48217

R/W

User Defined #7 Service Interval

Units
Vibration (Fg)
Seconds
Vibration (Fg)
Seconds
Vibration (Fg)
Seconds
Temperature
Seconds
Temperature
Seconds
Temperature
Seconds
Temperature
Seconds
Temperature
Seconds
Temperature
Seconds
Temperature
Seconds
Temperature
Seconds
Temperature
Seconds
Temperature
Seconds

Hours

090.020-CS (JUNE 11)


Page 92

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

8217

N112:17

48218

R/W

User Defined #8 Service Interval

8218

N112:18

48219

R/W

Oil Analysis - Next Service

8219

N112:19

48220

R/W

Change Filters - Next Service

8220

N112:20

48221

R/W

Clean Oil Stainers - Next Service

8221

N112:21

48222

R/W

Clean Liquid Strainers - Next Service

8222

N112:22

48223

R/W

Clean Coalescers - Next Service

8223

N112:23

48224

R/W

Clean Suction Screen - Next Service

8224

N112:24

48225

R/W

Vibration Analysis - Next Service

8225

N112:25

48226

R/W

Check Coupling - Next Service

8226

N112:26

48227

R/W

Grease Motor - Next Service

8227

N112:27

48228

R/W

User Defined #1 - Next Service

8228

N112:28

48229

R/W

User Defined #2 - Next Service

8229

N112:29

48230

R/W

User Defined #3 - Next Service

8230

N112:30

48231

R/W

User Defined #4 - Next Service

8231

N112:31

48232

R/W

User Defined #5 - Next Service

8232

N112:32

48233

R/W

User Defined #6 - Next Service

8233

N112:33

48234

R/W

User Defined #7 - Next Service

8234

N112:34

48235

R/W

User Defined #8 - Next Service

8300

N113:00

48301

R/W

Sequencing - System 1 Compressor 1 ID

8301

N113:01

48302

R/W

Sequencing - System 1 Compressor 2 ID

8302

N113:02

48303

R/W

Sequencing - System 1 Compressor 3 ID

8303

N113:03

48304

R/W

Sequencing - System 1 Compressor 4 ID

8304

N113:04

48305

R/W

Sequencing - System 1 Compressor 5 ID

8305

N113:05

48306

R/W

Sequencing - System 1 Compressor 6 ID

8306

N113:06

48307

R/W

Sequencing - System 1 Compressor 7 ID

8307

N113:07

48308

R/W

Sequencing - System 1 Compressor 8 ID

8308

N113:08

48309

R/W

Sequencing - System 1 Compressor 1 Start #

8309

N113:09

48310

R/W

Sequencing - System 1 Compressor 2 Start #

8310

N113:10

48311

R/W

Sequencing - System 1 Compressor 3 Start #

8311

N113:11

48312

R/W

Sequencing - System 1 Compressor 4 Start #

8312

N113:12

48313

R/W

Sequencing - System 1 Compressor 5 Start #

8313

N113:13

48314

R/W

Sequencing - System 1 Compressor 6 Start #

8314

N113:14

48315

R/W

Sequencing - System 1 Compressor 7 Start #

8315

N113:15

48316

R/W

Sequencing - System 1 Compressor 8 Start #

8316

N113:16

48317

R/W

Sequencing - System 1 Capacity Control Setpoint

8317

N113:17

48318

R/W

Sequencing - System 1 Control Point

8318

N113:18

48319

R/W

Sequencing - System 1 Minimum Run Time

8319

N113:19

48320

R/W

Sequencing - System 1 Compressor 1 Capacity

8320

N113:20

48321

R/W

Sequencing - System 1 Compressor 2 Capacity

8321

N113:21

48322

R/W

Sequencing - System 1 Compressor 3 Capacity

8322

N113:22

48323

R/W

Sequencing - System 1 Compressor 4 Capacity

8323

N113:23

48324

R/W

Sequencing - System 1 Compressor 5 Capacity

Units

Hours

None

Temperature
Minutes

Real

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 93

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

8324

N113:24

48325

R/W

Sequencing - System 1 Compressor 6 Capacity

8325

N113:25

48326

R/W

Sequencing - System 1 Compressor 7 Capacity

8326

N113:26

48327

R/W

Sequencing - System 1 Compressor 8 Capacity

8327

N113:27

48328

R/W

Sequencing - System 1 Compressor 1 Run Time

8328

N113:28

48329

R/W

Sequencing - System 1 Compressor 2 Run Time

8329

N113:29

48330

R/W

Sequencing - System 1 Compressor 3 Run Time

8330

N113:30

48331

R/W

Sequencing - System 1 Compressor 4 Run Time

8331

N113:31

48332

R/W

Sequencing - System 1 Compressor 5 Run Time

8332

N113:32

48333

R/W

Sequencing - System 1 Compressor 6 Run Time

8333

N113:33

48334

R/W

Sequencing - System 1 Compressor 7 Run Time

8334

N113:34

48335

R/W

Sequencing - System 1 Compressor 8 Run Time

8335

N113:35

48336

R/W

Sequencing - System 1 Compressor 1 Minimum Capacity

8336

N113:36

48337

R/W

Sequencing - System 1 Compressor 2 Minimum Capacity

8337

N113:37

48338

R/W

Sequencing - System 1 Compressor 3 Minimum Capacity

8338

N113:38

48339

R/W

Sequencing - System 1 Compressor 4 Minimum Capacity

8339

N113:39

48340

R/W

Sequencing - System 1 Compressor 5 Minimum Capacity

8340

N113:40

48341

R/W

Sequencing - System 1 Compressor 6 Minimum Capacity

8341

N113:41

48342

R/W

Sequencing - System 1 Compressor 7 Minimum Capacity

8342

N113:42

48343

R/W

Sequencing - System 1 Compressor 8 Minimum Capacity

8343

N113:43

48344

R/W

Sequencing - System 1 Compressor 1 Slave Command

8344

N113:44

48345

R/W

Sequencing - System 1 Compressor 2 Slave Command

8345

N113:45

48346

R/W

Sequencing - System 1 Compressor 3 Slave Command

8346

N113:46

48347

R/W

Sequencing - System 1 Compressor 4 Slave Command

8347

N113:47

48348

R/W

Sequencing - System 1 Compressor 5 Slave Command

8348

N113:48

48349

R/W

Sequencing - System 1 Compressor 6 Slave Command

8349

N113:49

48350

R/W

Sequencing - System 1 Compressor 7 Slave Command

8350

N113:50

48351

R/W

Sequencing - System 1 Compressor 8 Slave Command

8351

N113:51

48352

R/W

Sequencing - System 1 Compressor 1 Start Inhibits

8352

N113:52

48353

R/W

Sequencing - System 1 Compressor 2 Start Inhibits

8353

N113:53

48354

R/W

Sequencing - System 1 Compressor 3 Start Inhibits

8354

N113:54

48355

R/W

Sequencing - System 1 Compressor 4 Start Inhibits

8355

N113:55

48356

R/W

Sequencing - System 1 Compressor 5 Start Inhibits

8356

N113:56

48357

R/W

Sequencing - System 1 Compressor 6 Start Inhibits

8357

N113:57

48358

R/W

Sequencing - System 1 Compressor 7 Start Inhibits

8358

N113:58

48359

R/W

Sequencing - System 1 Compressor 8 Start Inhibits

8400

N114:00

48401

R/W

Sequencing System 2 Compressor 1 ID

8401

N114:01

48402

R/W

Sequencing System 2 Compressor 2 ID

8402

N114:02

48403

R/W

Sequencing System 2 Compressor 3 ID

8403

N114:03

48404

R/W

Sequencing System 2 Compressor 4 ID

8404

N114:04

48405

R/W

Sequencing System 2 Compressor 5 ID

8405

N114:05

48406

R/W

Sequencing System 2 Compressor 6 ID

8406

N114:06

48407

R/W

Sequencing System 2 Compressor 7 ID

Units

Real

Integer

Percent (%)

None

None

090.020-CS (JUNE 11)


Page 94

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

8407

N114:07

48408

R/W

Sequencing - System 2 Compressor 8 ID

8408

N114:08

48409

R/W

Sequencing - System 2 Compressor 1 Start #

8409

N114:09

48410

R/W

Sequencing - System 2 Compressor 2 Start #

8410

N114:10

48411

R/W

Sequencing - System 2 Compressor 3 Start #

8411

N114:11

48412

R/W

Sequencing - System 2 Compressor 4 Start #

8412

N114:12

48413

R/W

Sequencing - System 2 Compressor 5 Start #

8413

N114:13

48414

R/W

Sequencing - System 2 Compressor 6 Start #

8414

N114:14

48415

R/W

Sequencing - System 2 Compressor 7 Start #

8415

N114:15

48416

R/W

Sequencing - System 2 Compressor 8 Start #

8416

N114:16

48417

R/W

Sequencing - System 2 Capacity Control Setpoint

8417

N114:17

48418

R/W

Sequencing - System 2 Control Point

8418

N114:18

48419

R/W

Sequencing - System 2 Minimum Run Time

8419

N114:19

48420

R/W

Sequencing - System 2 Compressor 1 Capacity

8420

N114:20

48421

R/W

Sequencing - System 2 Compressor 2 Capacity

8421

N114:21

48422

R/W

Sequencing - System 2 Compressor 3 Capacity

8422

N114:22

48423

R/W

Sequencing - System 2 Compressor 4 Capacity

8423

N114:23

48424

R/W

Sequencing - System 2 Compressor 5 Capacity

8424

N114:24

48425

R/W

Sequencing - System 2 Compressor 6 Capacity

8425

N114:25

48426

R/W

Sequencing - System 2 Compressor 7 Capacity

8426

N114:26

48427

R/W

Sequencing - System 2 Compressor 8 Capacity

8427

N114:27

48428

R/W

Sequencing - System 2 Compressor 1 Run Time

8428

N114:28

48429

R/W

Sequencing - System 2 Compressor 2 Run Time

8429

N114:29

48430

R/W

Sequencing - System 2 Compressor 3 Run Time

8430

N114:30

48431

R/W

Sequencing - System 2 Compressor 4 Run Time

8431

N114:31

48432

R/W

Sequencing - System 2 Compressor 5 Run Time

8432

N114:32

48433

R/W

Sequencing - System 2 Compressor 6 Run Time

8433

N114:33

48434

R/W

Sequencing - System 2 Compressor 7 Run Time

8434

N114:34

48435

R/W

Sequencing - System 2 Compressor 8 Run Time

8435

N114:35

48436

R/W

Sequencing - System 2 Compressor 1 Minimum Capacity

8436

N114:36

48437

R/W

Sequencing - System 2 Compressor 2 Minimum Capacity

8437

N114:37

48438

R/W

Sequencing - System 2 Compressor 3 Minimum Capacity

8438

N114:38

48439

R/W

Sequencing - System 2 Compressor 4 Minimum Capacity

8439

N114:39

48440

R/W

Sequencing - System 2 Compressor 5 Minimum Capacity

8440

N114:40

48441

R/W

Sequencing - System 2 Compressor 6 Minimum Capacity

8441

N114:41

48442

R/W

Sequencing - System 2 Compressor 7 Minimum Capacity

8442

N114:42

48443

R/W

Sequencing - System 2 Compressor 8 Minimum Capacity

8443

N114:43

48444

R/W

Sequencing - System 2 Compressor 1 Slave Command

8444

N114:44

48445

R/W

Sequencing - System 2 Compressor 2 Slave Command

8445

N114:45

48446

R/W

Sequencing - System 2 Compressor 3 Slave Command

8446

N114:46

48447

R/W

Sequencing - System 2 Compressor 4 Slave Command

8447

N114:47

48448

R/W

Sequencing - System 2 Compressor 5 Slave Command

8448

N114:48

48449

R/W

Sequencing - System 2 Compressor 6 Slave Command

8449

N114:49

48450

R/W

Sequencing - System 2 Compressor 7 Slave Command

Units

None

Temperature
Minutes

Real

Integer

Percent (%)

None

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 95

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

8450

N114:50

48451

R/W

Sequencing - System 2 Compressor 8 Slave Command

8451

N114:51

48452

R/W

Sequencing - System 2 Compressor 1 Start Inhibits

8452

N114:52

48453

R/W

Sequencing - System 2 Compressor 2 Start Inhibits

8453

N114:53

48454

R/W

Sequencing - System 2 Compressor 3 Start Inhibits

8454

N114:54

48455

R/W

Sequencing - System 2 Compressor 4 Start Inhibits

8455

N114:55

48456

R/W

Sequencing - System 2 Compressor 5 Start Inhibits

8456

N114:56

48457

R/W

Sequencing - System 2 Compressor 6 Start Inhibits

8457

N114:57

48458

R/W

Sequencing - System 2 Compressor 7 Start Inhibits

8458

N114:58

48459

R/W

Sequencing - System 2 Compressor 8 Start Inhibits

8500

N115:00

48501

R/W

Sequencing - System 3 Compressor 1 ID

8501

N115:01

48502

R/W

Sequencing - System 3 Compressor 2 ID

8502

N115:02

48503

R/W

Sequencing - System 3 Compressor 3 ID

8503

N115:03

48504

R/W

Sequencing - System 3 Compressor 4 ID

8504

N115:04

48505

R/W

Sequencing - System 3 Compressor 5 ID

8505

N115:05

48506

R/W

Sequencing - System 3 Compressor 6 ID

8506

N115:06

48507

R/W

Sequencing - System 3 Compressor 7 ID

8507

N115:07

48508

R/W

Sequencing - System 3 Compressor 8 ID

8508

N115:08

48509

R/W

Sequencing - System 3 Compressor 1 Start #

8509

N115:09

48510

R/W

Sequencing - System 3 Compressor 2 Start #

8510

N115:10

48511

R/W

Sequencing - System 3 Compressor 3 Start #

8511

N115:11

48512

R/W

Sequencing - System 3 Compressor 4 Start #

8512

N115:12

48513

R/W

Sequencing - System 3 Compressor 5 Start #

8513

N115:13

48514

R/W

Sequencing - System 3 Compressor 6 Start #

8514

N115:14

48515

R/W

Sequencing - System 3 Compressor 7 Start #

8515

N115:15

48516

R/W

Sequencing - System 3 Compressor 8 Start #

8516

N115:16

48517

R/W

Sequencing - System 3 Capacity Control Setpoint

8517

N115:17

48518

R/W

Sequencing - System 3 Control Point

8518

N115:18

48519

R/W

Sequencing - System 3 Minimum Run Time

8519

N115:19

48520

R/W

Sequencing - System 3 Compressor 1 Capacity

8520

N115:20

48521

R/W

Sequencing - System 3 Compressor 2 Capacity

8521

N115:21

48522

R/W

Sequencing - System 3 Compressor 3 Capacity

8522

N115:22

48523

R/W

Sequencing - System 3 Compressor 4 Capacity

8523

N115:23

48524

R/W

Sequencing - System 3 Compressor 5 Capacity

8524

N115:24

48525

R/W

Sequencing - System 3 Compressor 6 Capacity

8525

N115:25

48526

R/W

Sequencing - System 3 Compressor 7 Capacity

8526

N115:26

48527

R/W

Sequencing - System 3 Compressor 8 Capacity

8527

N115:27

48528

R/W

Sequencing - System 3 Compressor 1 Run Time

8528

N115:28

48529

R/W

Sequencing System 3 Compressor 2 Run Time

8529

N115:29

48530

R/W

Sequencing System 3 Compressor 3 Run Time

8530

N115:30

48531

R/W

Sequencing System 3 Compressor 4 Run Time

8531

N115:31

48532

R/W

Sequencing System 3 Compressor 5 Run Time

8532

N115:32

48533

R/W

Sequencing System 3 Compressor 6 Run Time

Units

None

None

Temperature
Minutes

Real

Integer

090.020-CS (JUNE 11)


Page 96

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address

Read/
Write

Description of Data

8533

N115:33

48534

R/W

Sequencing System 3 Compressor 7 Run Time

8534

N115:34

48535

R/W

Sequencing - System 3 Compressor 8 Run Time

8535

N115:35

48536

R/W

Sequencing - System 3 Compressor 1 Minimum Capacity

8536

N115:36

48537

R/W

Sequencing - System 3 Compressor 2 Minimum Capacity

8537

N115:37

48538

R/W

Sequencing - System 3 Compressor 3 Minimum Capacity

8538

N115:38

48539

R/W

Sequencing - System 3 Compressor 4 Minimum Capacity

8539

N115:39

48540

R/W

Sequencing - System 3 Compressor 5 Minimum Capacity

8540

N115:40

48541

R/W

Sequencing - System 3 Compressor 6 Minimum Capacity

8541

N115:41

48542

R/W

Sequencing - System 3 Compressor 7 Minimum Capacity

8542

N115:42

48543

R/W

Sequencing - System 3 Compressor 8 Minimum Capacity

8543

N115:43

48544

R/W

Sequencing - System 3 Compressor 1 Slave Command

8544

N115:44

48545

R/W

Sequencing - System 3 Compressor 2 Slave Command

8545

N115:45

48546

R/W

Sequencing - System 3 Compressor 3 Slave Command

8546

N115:46

48547

R/W

Sequencing - System 3 Compressor 4 Slave Command

8547

N115:47

48548

R/W

Sequencing - System 3 Compressor 5 Slave Command

8548

N115:48

48549

R/W

Sequencing - System 3 Compressor 6 Slave Command

8549

N115:49

48550

R/W

Sequencing - System 3 Compressor 7 Slave Command

8550

N115:50

48551

R/W

Sequencing - System 3 Compressor 8 Slave Command

8551

N115:51

48552

R/W

Sequencing - System 3 Compressor 1 Start Inhibits

8552

N115:52

48553

R/W

Sequencing - System 3 Compressor 2 Start Inhibits

8553

N115:53

48554

R/W

Sequencing - System 3 Compressor 3 Start Inhibits

8554

N115:54

48555

R/W

Sequencing - System 3 Compressor 4 Start Inhibits

8555

N115:55

48556

R/W

Sequencing - System 3 Compressor 5 Start Inhibits

8556

N115:56

48557

R/W

Sequencing - System 3 Compressor 6 Start Inhibits

8557

N115:57

48558

R/W

Sequencing - System 3 Compressor 7 Start Inhibits

8558

N115:58

48559

R/W

Sequencing - System 3 Compressor 8 Start Inhibits

Units
Integer

Percent (%)

None

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 97

COMMANDS:
Frick
AB
Modbus
Address Address Address
8910
N119:10
48911
8911
N119:11
48912

Read/
Write
W
W

Description of Data

Value Codes

Remote Start
Remote Stop

8912

N119:12

48913

Remote - Load Slide Valve

8913

N119:13

48914

Remote - Unload Slide Valve

8914

N119:14

48915

Remote - RDB Capacity

8915

N119:15

48916

Remote - Compressor Mode

8916

N119:16

48917

Remote - Capacity Mode

8917
8918

N119:17
N119:18

48918
48919

W
W

Remote - Clear Alarms


Remote - Clear Recycle Delay

8919

N119:19

48920

Remote - Sequencing Mode

8920

N119:20

48921

Remote - Communication Units

8921

N119:21

48922

Remote - Regulation Mode

8922
8923
8924

N119:22
N119:23
N119:24

48923
48924
48925

W
W
W

Remote Set Slide Valve Position


Remote Set Drive Speed
Remote Set Total Capacity

GENERAL NOTES:
Command Values need tenths field added. For example, to
start the compressor, the table above states that 1 = Start.
However, being that one decimal place is assumed, a value of
10 actually needs to be sent.
SPECIFIC NOTES:
Note 1: The compressor must be in remote communications
to accept the start and stop commands that are sent through
serial communications, and the Capacity Mode must be in remote communications to accept load and unload commands
that are sent.
Note 2: To read the proper Temperature/Pressure units, use
Frick address 4566. To change (write to) the Temperature/
Pressure units, use Frick address 8920.
Note 3: Mode must already be enabled.
Note 4: The value passed with this command is the position
(percentage) to which the control will attempt to set the Slide
Valve. The control will automatically load and/or unload the
Slide Valve until it is within a deadband (+/- 0.5%) of the target.
Conditions:

the compressor must be running

1 = Start
1 = Stop
0 = Turn off
See Note 1
1 15 = Load x seconds
0 = Turn off
1 15 = Unload x seconds
25, 50, 75, 100 (represents capacity %)
0 = Manual
1 = Auto
2 = Remote -- Communications
3 = Remote -- I/O
5 = Remote -- Sequencing
6 = Manual -- Browser
1 = Auto
2 = Remote -- Communications
3 = Remote -- I/O
4 = Remote -- 4-20ma
5 = Remote Sequencing
6 = Manual -- Browser
1 = Clear Alarms
1 = Clear Recycle Delay
0 = Disable
1 = Enable
0 = C / PSIA
See Note 2
1 = Panel Units
0 = Regulation Mode 1
1 = Regulation Mode 2
See Note 3
2 = Regulation Mode 3
3 = Regulation Mode 4
0 100%
See Note 4
0 100%
See Note 5
0 - 200
See Note 6

the Capacity Mode must be Remote Comms


if the compressor is Variable Speed, the Slide
Valve will not go below the Variable Speed Minimum Slide Valve setpoint

This command is reset by a Remote Load or Remote Unload


command
Note 5: The value passed with this command is the speed
(percentage) to which the control will attempt to set the Drive.
Conditions:

the compressor must be Variable Speed

the compressor must be running

the Capacity Mode must be Remote Comms

the Drive will not go below the Drive Speed Minimum setpoint
This command is reset by a Remote Load or Remote Unload
command
Note 6: This command is actually a combination the previous two (Remote Set Slide Valve Position and Remote Set
Drive Speed), and is for the convenience of the PLC programmer. A value of X from 0 to 100 will set the Slide Valve Position
to X% and the Drive Speed to 0% (or the allowable minimum).
A value of X from 100 to 200 will set the Slide Valve to 100%
and the Drive Speed to (X 100)%.

090.020-CS (JUNE 11)


Page 98

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

DBS SETPOINT VALUES:


Frick
AB
Modbus
Address Address Address
8950
N119:50
48951
8951
N119:51
48952
8952
N119:52
48953
8953
N119:53
48954
8954
N119:54
48955
8955
N119:55
48956
8956
N119:56
48957
8957
N119:57
48958
8958
N119:58
48959
8959
N119:59
48960
8960
N119:60
48961
8961
N119:61
48962
8962
N119:62
48963
8963
N119:63
48964
8964
N119:64
48965
8965
N119:65
48966
8966
N119:66
48967
8967
N119:67
48968
8968
N119:68
48969
8969
N119:69
48970
8970
N119:70
48971
8971
N119:71
48972
8972
N119:72
48973
8973
N119:73
48974
8974
N119:74
48975
8975
N119:75
48976
8976
N119:76
48977
8977
N119:77
48978
8978
N119:78
48979
8979
N119:79
48980
8980
N119:80
48981
8981
N119:81
48982
8982
N119:82
48983
8983
N119:83
48984
8984
N119:84
48985
8985
N119:85
48986
8986
N119:86
48987
8987
N119:87
48988
8988
N119:88
48989
8989
N119:89
48990
8990
N119:90
48991
8991
N119:91
48992
8992
N119:92
48993
8993
N119:93
48994
8994
N119:94
48995
8995
N119:95
48996
8997

N119:97

48998

Read/
Write
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R

Description of Data
Average Current
Elapsed Run Time Hours
Elapsed Run Time Minutes
Current Phase A
Current Phase B
Current Phase C
Heatsink Temperature
RTD Temperature
Thermal Capacity Used
Time until Start
Full Load Amps
Locked Rotor Current
Stall Time
Jam Current Level
Jam Run Delay
DBS Service Factor
Current Unbalance Alarm Level
Current Unbalance Alarm Run Delay
RTD Temperature Alarm Level
RTD Temperature Trip Level
Bypass Time
Constant Current Level
Ramp Time
DBS Version
Last Trip Current
Last Trip Heatsink Temp
Last Trip RTD Temp
Last Trip Thermal Capacity
Last Trip FLA
Last Trip Current Step
Last Trip Ramp Time
Last Trip Bypass Time
Last Run Time Hours
Last Run Time Minutes
Total Accumulated Run Time Hours
Total Accumulated Run Time Minutes
Total Number of Starts
Total Short Circuit Trips
Total Jam Trips
Total Phase Loss Trips
Total Phase Reversal Trips
Total Current Unbalance Trips
Total Heatsink Overtemp Trips
Total RTD Overtemp Trips
Total Thermal Overload Trips
Maximum RTD Temperature
Locked Rotor Current Setpoint

Units
Amps
Hours
Minutes
Amps

Temperature
Percent (%)
Minutes
Amps
Percent (%)
Seconds
Percent (%)
Seconds
Percent (%)
Seconds
Temperature
Seconds
Percent (%)
Seconds
Real
Amps
Temperature
Percent (%)
Amps
Percent (%)
Seconds
Hours
Minutes
Hours
Minutes

None

Temperature
Percent (%)

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 99

DBS SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address
8998
N119:98
48999
8999
N119:99
49000
9000
N120:00 49001
9001
N120:01 49002
9002
N120:02 49003
9003
N120:03 49004
9004
N120:04 49005
9005
N120:05 49006
9007

N120:07

49008

Read/
Write
R
R
R
R
R
R
R
R
R

Description of Data

Units

Stall Time Setpoint


Jam Current Level Setpoint
Jam Run Delay Setpoint
DBS Service Factor Setpoint
Current Unbalance Alarm Level Setpoint
Current Unbalance Alarm Run Delay Setpoint
RTD Temperature Alarm Level Setpoint
RTD Temperature Trip Level Setpoint

Seconds
Percent (%)
Seconds
Percent (%)

DBS Command Flags

Seconds
Temperature

None

GENERAL SETPOINT VALUES:


Frick
AB
Modbus
Address Address Address
9100
N121:00
49101
9101
N121:01
49102

Read/
Write
R/W
R/W

Frick
AB
Modbus
Address Address Address
9200
N122:00
49201

Read/
Write
R/W

Description of Data

Units

Real Time Trending Recording Interval


History Trending Recording Interval

Seconds
Minutes

VSD (VYPER) SETPOINT VALUES:


Description of Data
Vyper Drive Standby Time

Units
Minutes

(NOTE: RPM values are


NOT multiplied by 10
in Allen-Bradley and
MODBUS protocols)

9210

N122:10

49211

Vyper Drive Auto Speed Command

9211

N122:11

49212

Vyper Drive Run Command

None

9215
9216

N122:15
N122:16

49216
49217

R
R

Vyper Drive Current Fault


Vyper Drive Current Warning

None

(NOTE: RPM values are


NOT multiplied by 10
in Allen-Bradley and
MODBUS protocols)

9218

N122:18

49219

Vyper Drive Speed Command

9219

N122:19

49220

Vyper Drive Percent of Full Load Amps Percent (%)

9220

N122:20

49221

Vyper Drive Actual Speed

9223
9224
9225
9226

N122:23
N122:24
N122:25
N122:26

49224
49225
49226
49227

R
R
R
R

Vyper Drive Operating Mode


Vyper Drive Water Pump
Vyper Drive Precharge Relay
Vyper Drive Trigger SCRs

9228
9229
9230

N122:28
N122:29
N122:30

49229
49230
49231

R
R
R

Vyper Drive Output Frequency


Vyper Drive Output Voltage
Vyper Drive DC Bus Voltage

(NOTE: RPM values are


NOT multiplied by 10
in Allen-Bradley and
MODBUS protocols)

RPM

RPM

RPM

None

Real
Integer

090.020-CS (JUNE 11)


Page 100

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

VSD (VYPER) SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address
9231
N122:31
49232
9232
N122:32
49233
9233
N122:33
49234
9234
N122:34
49235
9235
N122:35
49236
9236
N122:36
49237
9237
N122:37
49238
9238
N122:38
49239
9239
N122:39
49240
9240
N122:40
49241

Read/
Write
R
R
R
R
R
R
R
R
R
R

Description of Data
Vyper Drive Job FLA
Vyper Drive DC Inverter Link Current
Vyper Drive Phase A Current
Vyper Drive Phase B Current
Vyper Drive Phase C Current
Vyper Drive Ambient Temperature
Vyper Drive Baseplate Temperature
Vyper Drive Converter Heatsink Temperature
Vyper Drive Motor Temperature
Vyper Drive Input Power

9242
9243

N122:42
N122:43

49243
49244

R
R

Vyper Drive Total Kilowatts per hour


Vyper Drive Model

9244
9245
9246
9247
9248
9249
9250
9251
9252
9253
9254
9255
9256
9257
9258
9259
9260
9261
9262
9263
9264
9265
9266
9267
9268
9269
9270
9271

N122:44
N122:45
N122:46
N122:47
N122:48
N122:49
N122:50
N122:51
N122:52
N122:53
N122:54
N122:55
N122:56
N122:57
N122:58
N122:59
N122:60
N122:61
N122:62
N122:63
N122:64
N122:65
N122:66
N122:67
N122:68
N122:69
N122:70
N122:71

49245
49246
49247
49248
4249
49250
49251
49252
49253
49254
49255
49256
49257
49258
49259
49260
49261
49262
49263
49264
49265
49266
49267
49268
49269
49270
49271
49272

R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R

9272

N122:72

49273

9273
9274
9275

N122:73
N122:74
N122:75

49274
49275
49276

R
R
R

Harmonic Filter Present


Harmonic Filter Operating Mode
Harmonic Filter Supply Contactor Energized
Harmonic Filter Precharge Contactor Energized
Harmonic Filter Phase Rotation Direction
Harmonic Filter DC Bus Voltage
Harmonic Filter L1-N Voltage
Harmonic Filter L2-N Voltage
Harmonic Filter L3-N Voltage
Harmonic Filter L1-L2 Voltage
Harmonic Filter L2-L3 Voltage
Harmonic Filter L3-L1 Voltage
Harmonic Filter L1 Total Harmonic Distortion
Harmonic Filter L2 Total Harmonic Distortion
Harmonic Filter L3 Total Harmonic Distortion
Harmonic Filter L1 Filter Current
Harmonic Filter L2 Filter Current
Harmonic Filter L3 Filter Current
Harmonic Filter L1 Supply Current
Harmonic Filter L2 Supply Current
Harmonic Filter L3 Supply Current
Harmonic Filter L1 Total Demand Distortion
Harmonic Filter L2 Total Demand Distortion
Harmonic Filter L3 Total Demand Distortion
Harmonic Filter Total Supply KVA
Harmonic Filter Total Power Factor
Harmonic Filter Baseplate Temperature
Vyper Drive Auto/Manual Switch Status
(NOTE: RPM values are
Vyper Drive Manual Mode Speed NOT multiplied by 10
Switch Status
in Allen-Bradley and
MODBUS protocols)
Vyper Drive Line Frequency Jumper Status
Vyper Drive Run Command Signal Status
Vyper Drive No Faults Present Signal Status

Units

Amps

Temperature

kW

Integer

None

Integer

Percent (%)

Amps

Percent (%)
Integer
Real
Temperature
None
RPM

None

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 101

VSD (VYPER) SETPOINT VALUES (Continued):


Frick
AB
Modbus
Address Address Address
9276
N122:76
49277
9277
N122:77
49278
9278
N122:78
49279
9279
N122:79
49280
9280
N122:80
49281
9281
N122:81
49282
9282
N122:82
49283
9283
N122:83
49284
9284
N122:84
49285
9285
N122:85
49286
9286
N122:86
49287
9287
N122:87
49288
9288
N122:88
49289
9289
N122:89
49290
9290
N122:90
49291
9291
N122:91
49292
9295
9296
9297
9298
9299
9300
9301
9302
9303
9304
9305
9306
9307
9308
9309
9310
9311
9312
9313
9314

N122:95
N122:96
N122:97
N122:98
N122:99
N123:00
N123:01
N123:02
N123:03
N123:04
N123:05
N123:06
N123:07
N123:08
N123:09
N123:10
N123:11
N123:12
N123:13
N123:14

49296
49297
49298
49299
49300
49301
49302
49303
49304
49305
49306
49307
49308
49309
49310
49311
49312
49313
49314
49315

Read/
Write
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R

Description of Data
Vyper Drive Run Acknowledge Relay Status
Vyper Drive Run Command Relay Status
Vyper Drive Interface Board Software Version
Vyper Drive Software Version
Vyper Drive Modbus Node ID
Vyper Drive IB Transmit Errors
Vyper Drive CP to IB Time Out Errors
Vyper Drive VD to IB Time Out Errors
Vyper Drive IB to VD Receive Errors
Vyper Drive VD to IB Checksum Errors
Vyper Drive HF to IB Time Out Errors
Vyper Drive VD to HF Receive Errors
Vyper Drive HF to IB Checksum Errors
Vyper Drive Software Reboots
Vyper Drive Phase B Baseplate Temperature
Vyper Drive Phase C Baseplate Temperature
Vyper Drive Fault #1
Vyper Drive Warning #1
Vyper Drive Fault #2
Vyper Drive Warning #2
Vyper Drive Fault #3
Vyper Drive Warning #3
Vyper Drive Fault #4
Vyper Drive Warning #4
Vyper Drive Fault #5
Vyper Drive Warning #5
Vyper Drive Fault #6
Vyper Drive Warning #6
Vyper Drive Fault #7
Vyper Drive Warning #7
Vyper Drive Fault #8
Vyper Drive Warning #8
Vyper Drive Fault #9
Vyper Drive Warning #9
Vyper Drive Fault #10
Vyper Drive Warning #10

Units

None

Temperature

090.020-CS (JUNE 11)


Page 102

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 103

SECTION 7
WARNING/SHUTDOWN MESSAGE CODES
The following list represents all of the current warning/
shutdown messages that are potentially displayable. The
numeric value to the left of each message corresponds to
the value that is read from the Safety Message addresses
(Frick address 3070 3079). As an example, if Frick address 3070 were being read, and it returned a value of
51, then referring to the chart on the following pages, it
would be found that the code of 51 represents Oil Level
Shutdown.
3

Balance Piston 1 Shutdown

Balance Piston 2 Shutdown

Balance Piston 3 Shutdown

Liquid Slugging Warning

Liquid Slugging Shutdown

High Oil Filter Pressure Warning

High Oil Filter Pressure Shutdown

10

Missing Comp. Oil Pressure Warning

11

Missing Comp. Oil Pressure Shutdown A

12

Missing Comp. Oil Pressure Shutdown B

13

Insufficient Main Oil Pressure Shutdown

14

High Motor Current Shutdown

15

High Motor Current Warning

16

Low Motor Current Shutdown

17

High Discharge Temperature Sensor Fault

18

High Discharge Temperature Shutdown

19

High Discharge Temperature Warning

20

High Suction Pressure Shutdown

21

High Suction Pressure Warning

22

Low Separator Temperature Shutdown

23

Low Separator Temperature Warning

24

High Comp. Oil Temperature Shutdown

25

High Comp. Oil Temperature Warning

26

Low Comp. Oil Temperature Shutdown

27

Low Comp. Oil Temperature Warning

28

Low Suction Shutdown - Regulation Mode 1

29

Low Suction Warning - Regulation Mode 1

30

Low Suction Shutdown - Regulation Mode 2

31

Low Suction Warning - Regulation Mode 2

32

Low Suction Shutdown - Regulation Mode 3

33

Low Suction Warning - Regulation Mode 3

34

Low Suction Shutdown - Regulation Mode 4

35

Low Suction Warning - Regulation Mode 4

36

Regulation Mode 1 Shutdown

37

Regulation Mode 1 Warning

38

Regulation Mode 2 Shutdown

39

Regulation Mode 2 Warning

40

Regulation Mode 3 Shutdown

41

Regulation Mode 3 Warning

42

Regulation Mode 4 Shutdown

43

Regulation Mode 4 Warning

44

Low RPM Shutdown

45

Low RPM Warning

46

High RPM Shutdown

47

High RPM Warning

48

High Manifold Pressure Shutdown

49

High Manifold Pressure Warning

50

Low Main Oil Injection Pressure Shutdown

51

Oil Level Shutdown

52

Compressor Capacity Unload Alarm

53

False Running Fail -- Motor Amps

54

False Running Fail -- Confirmed Running Inp

55

High Limit Disch Pres Shutdown

56

High Limit Disch Temp Shutdown

57

High Disch Pres Shutdown -- Mode 1

58

High Disch Pres Warning -- Mode 1

59

High Disch Pres Shutdown -- Mode 2

60

High Disch Pres Warning -- Mode 2

61

Start Failure Shutdown For Eng And Turb

62

High Liquid Level Shutdown

63

Auxiliary Input 1 Shutdown

64

Auxiliary Input 1 Warning

65

Auxiliary Input 2 Shutdown

66

Auxiliary Input 2 Warning

67

Auxiliary Input 3 Shutdown

68

Auxiliary Input 3 Warning

69

Auxiliary Input 4 Shutdown

70

Auxiliary Input 4 Warning

71

Auxiliary Input 5 Shutdown

72

Auxiliary Input 5 Warning

73

Auxiliary Input 6 Shutdown

74

Auxiliary Input 6 Warning

75

Auxiliary Input 7 Shutdown

090.020-CS (JUNE 11)


Page 104

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

WARNING/SHUTDOWN MESSAGE CODES (Continued)


76

Auxiliary Input 7 Warning

120

High Auxiliary Analog 10 Warning

77

Auxiliary Input 8 Shutdown

121

Low Auxiliary Analog 10 Shutdown

78

Auxiliary Input 8 Warning

122

Low Auxiliary Analog 10 Warning

79

Auxiliary Input 9 Shutdown

123

Low Suction Pressure Sensor Fault

80

Auxiliary Input 9 Warning

124

Low Discharge Pressure Sensor Fault

81

Auxiliary Input 10 Shutdown

125

High Discharge Pressure Sensor Fault

82

Auxiliary Input 10 Warning

126

Low Comp. Oil Pressure Sensor Fault

83

High Auxiliary Analog 1 Shutdown

127

High Comp. Oil Pressure Sensor Fault

84

High Auxiliary Analog 1 Warning

128

Low Discharge Temperature Sensor Fault

85

Low Auxiliary Analog 1 Shutdown

129

Low Comp. Oil Temperature Sensor Fault

86

Low Auxiliary Analog 1 Warning

130

Low Separator Temperature Sensor Fault

87

High Auxiliary Analog 2 Shutdown

131

Auxiliary Input 11 Shutdown

88

High Auxiliary Analog 2 Warning

132

Auxiliary Input 11 Warning

89

Low Auxiliary Analog 2 Shutdown

133

Auxiliary Input 12 Shutdown

90

Low Auxiliary Analog 2 Warning

134

Auxiliary Input 12 Warning

91

High Auxiliary Analog 3 Shutdown

134

Auxiliary Input 13 Shutdown

92

High Auxiliary Analog 3 Warning

136

Auxiliary Input 13 Warning

93

Low Auxiliary Analog 3 Shutdown

137

Auxiliary Input 14 Shutdown

94

Low Auxiliary Analog 3 Warning

138

Auxiliary Input 14 Warning

95

High Auxiliary Analog 4 Shutdown

139

Auxiliary Input 15 Shutdown

96

High Auxiliary Analog 4 Warning

140

Auxiliary Input 15 Warning

97

Low Auxiliary Analog 4 Shutdown

141

Auxiliary Input 16 Shutdown

98

Low Auxiliary Analog 4 Warning

142

Auxiliary Input 16 Warning

99

High Auxiliary Analog 5 Shutdown

143

Auxiliary Input 17 Shutdown

100

High Auxiliary Analog 5 Warning

144

Auxiliary Input 17 Warning

101

Low Auxiliary Analog 5 Shutdown

145

Auxiliary Input 18 Shutdown

102

Low Auxiliary Analog 5 Warning

146

Auxiliary Input 18 Warning

103

High Auxiliary Analog 6 Shutdown

147

Auxiliary Input 19 Shutdown

104

High Auxiliary Analog 6 Warning

148

Auxiliary Input 19 Warning

105

Low Auxiliary Analog 6 Shutdown

149

Auxiliary Input 20 Shutdown

106

Low Auxiliary Analog 6 Warning

150

Auxiliary Input 20 Warning

107

High Auxiliary Analog 7 Shutdown

151

High Auxiliary Analog 11 Shutdown

108

High Auxiliary Analog 7 Warning

152

High Auxiliary Analog 11 Warning

109

Low Auxiliary Analog 7 Shutdown

153

Low Auxiliary Analog 11 Shutdown

110

Low Auxiliary Analog 7 Warning

154

Low Auxiliary Analog 11 Warning

111

High Auxiliary Analog 8 Shutdown

155

High Auxiliary Analog 12 Shutdown

112

High Auxiliary Analog 8 Warning

156

High Auxiliary Analog 12 Warning

113

Low Auxiliary Analog 8 Shutdown

157

Low Auxiliary Analog 12 Shutdown

114

Low Auxiliary Analog 8 Warning

158

Low Auxiliary Analog 12 Warning

115

High Auxiliary Analog 9 Shutdown

159

High Auxiliary Analog 13 Shutdown

116

High Auxiliary Analog 9 Warning

160

High Auxiliary Analog 13 Warning

117

Low Auxiliary Analog 9 Shutdown

161

Low Auxiliary Analog 13 Shutdown

118

Low Auxiliary Analog 9 Warning

162

Low Auxiliary Analog 13 Warning

119

High Auxiliary Analog 10 Shutdown

163

High Auxiliary Analog 14 Shutdown

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 105

WARNING/SHUTDOWN MESSAGE CODES (Continued)


164

High Auxiliary Analog 14 Warning

208

Low Comp. Oil Pressure Shutdown

165

Low Auxiliary Analog 14 Shutdown

209

Low Oil Pressure Shutdown 2

166

Low Auxiliary Analog 14 Warning

210

High Compressor Vib Warning - Suction

167

High Auxiliary Analog 15 Shutdown

211

High Compressor Vib Warning - Discharge

168

High Auxiliary Analog 15 Warning

212

High Compressor Vib Shutdown - Suction

169

Low Auxiliary Analog 15 Shutdown

213

High Compressor Vib Shutdown - Discharge

170

Low Auxiliary Analog 15 Warning

214

High Motor Vib Warning - Shaft Side

171

High Auxiliary Analog 16 Shutdown

215

High Motor Vib Warning - Opp Shaft Side

172

High Auxiliary Analog 16 Warning

216

High Motor Vib Shutdown - Shaft Side

173

Low Auxiliary Analog 16 Shutdown

217

High Motor Vib Shutdown Opp Shaft Side

174

Low Auxiliary Analog 16 Warning

218

Compressor Auxiliary Shutdown

175

High Auxiliary Analog 17 Shutdown

220

Oil Log Shutdown

176

High Auxiliary Analog 17 Warning

221

DBS - Current Unbalance

177

Low Auxiliary Analog 17 Shutdown

222

DBS - RTD Temperature

178

Low Auxiliary Analog 17 Warning

223

DBS - Short Circuit

179

High Auxiliary Analog 18 Shutdown

224

DBS - Thermal Overload

180

High Auxiliary Analog 18 Warning

225

DBS - Shorted SCR

181

Low Auxiliary Analog 18 Shutdown

226

DBS - Phase Loss

182

Low Auxiliary Analog 18 Warning

227

DBS - Phase Reversal

183

High Auxiliary Analog 19 Shutdown

228

DBS - Jam

184

High Auxiliary Analog 19 Warning

229

DBS - HEATSINK Overtemperature

185

Low Auxiliary Analog 19 Shutdown

230

DBS - RTD Overtemperature

186

Low Auxiliary Analog 19 Warning

231

VSD Board Power Supply Fault

187

High Auxiliary Analog 20 Shutdown

233

VSD Board Motor Current > 15%

188

High Auxiliary Analog 20 Warning

234

VSD Board Run Signal Fault

189

Low Auxiliary Analog 20 Shutdown

235

VSD Board to Panel Comms Loss

190

Low Auxiliary Analog 20 Warning

237

VSD Initialization Fault

191

Analog Board 1 Communications Shutdown

238

VSD Stop Contacts Fault

192

Analog Board 2 Communications Shutdown

239

Harmonic Filter Logic Board Or Comms Fault

193

Digital Board 1 Communications Shutdown

240

Harmonic Filter High Total Demand Distortion

194

Digital Board 2 Communications Shutdown

241

VSD High Phase B Inverter Baseplate Temp

195

DBS Communication Failure Shutdown

242

VSD High Phase C Inverter Baseplate Temp

196

Digital Board 1 Reset

243

VSD Low Phase B Inverter Baseplate Temp

197

Digital Board 2 Reset

244

VSD Low Phase C Inverter Baseplate Temp

198

Starting Failure - No Compressor Auxiliary

247

VSD High Phase A Instantaneous Current

199

Starting Failure - Low Motor Amps

248

VSD High Phase B Instantaneous Current

200

VSD Communication Failure Warning

249

VSD High Phase C Instantaneous Current

201

Low Comp. Oil Pressure Shutdown

251

VSD Phase A Gate Driver Fault

202

Oil Pump Auxiliary Failure

252

VSD Phase B Gate Driver Fault

203

Oil Pump 1 Auxiliary Warning

253

VSD Phase C Gate Driver Fault

204

Oil Pump 1 Auxiliary Shutdown

254

VSD Single Phase Input Power Fault

205

Oil Pump 2 Auxiliary Warning

257

VSD 105% Motor Current Overload Fault

206

Oil Pump 2 Auxiliary Shutdown

258

VSD High DC Bus Voltage Fault

207

Low Comp. Oil Pressure Warning

259

VSD Logic Board Power Supply Fault

090.020-CS (JUNE 11)


Page 106

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

WARNING/SHUTDOWN MESSAGE CODES (Continued)


263

VSD Low DC Bus Voltage Fault

341

High Motor Temp Warning - Opp Shaft Side

264

VSD DC Bus Voltage Imbalance Fault

342

High Motor Temp Shutdown - Shaft Side

265

VSD High Internal Ambient Temp Fault

343

High Motor Temp Shutdown - Opp Shaft Side

266

VSD High Inverter Baseplate Temp Fault

344

High Motor Stator #1 Temp Warning

267

VSD Logic Board Processor Fault

345

High Motor Stator #1 Temp Shutdown

268

VSD Run Signal Fault

346

High Motor Stator #2 Temp Warning

269

VSD High Converter Heatsink Temp Fault

347

High Motor Stator #2 Temp Shutdown

270

VSD Invalid Current Scale Selection

348

High Motor Stator #3 Temp Warning

271

VSD Low Inverter Baseplate Temp Fault

349

High Motor Stator #3 Temp Shutdown

272

VSD Serial Communication Fault

350

Slide Valve Failure Shutdown

273

VSD Precharge Lockout Fault

351

DBS Communication Failure Warning

274

VSD Low Converter Heatsink Temp Fault

352

Low Oil Differential 1 (Kobe)

275

VSD Current Imbalance Fault

353

Low Oil Differential 2 (Kobe)

276

VSD Precharge - DC Bus Voltage Imbalance

354

High Oil Pressure (Kobe)

277

VSD Precharge - Low DC Bus Voltage 2

355

High Comp. Oil Pressure Shutdown

278

VSD Precharge - Low DC Bus Voltage 1

356

Coalescer Filter Differential Warning

280

Harmonic Filter High DC Bus Voltage Fault

357

Low Discharge Pressure Shutdown

281

Harmonic Filter High Phase C Current Fault

358

High Oil Temperature Sensor Fault

282

Harmonic Filter High Phase B Current Fault

359

High Separator Temperature Sensor Fault

283

Harmonic Filter High Phase A Current Fault

360

Low Main Oil Inj Pressure Sensor Warning

284

Harmonic Filter Phase Locked Loop Fault

361

High Main Oil Inj Pressure Sensor Warning

286

Harmonic Filter Logic Board Power Supply

362

Low Economizer Pressure Sensor Warning

295

Harmonic Filter Precharge - High DC Bus Volt

363

High Economizer Pressure Sensor Warning

296

Harmonic Filter Precharge - Low DC Bus Volt

364

Low Filter Pressure Sensor Warning

297

Harmonic Filter DC Current Transformer 1

365

High Filter Pressure Sensor Warning

298

Harmonic Filter DC Current Transformer 2

366

Low Intermediate Pressure Sensor Warning

299

Harmonic Filter High Baseplate Temp Fault

367

High Intermediate Pressure Sensor Warning

301

Harmonic Filter Low DC Bus Voltage

368

Low Bal Piston Pressure Sensor Warning

305

Harmonic Filter DC Bus Voltage Imbalance

369

High Bal Piston Pressure Sensor Warning

306

Harmonic Filter 110% Input Current Overload

370

Low System Disch Pressure Sensor Warning

307

Harmonic Filter Run Signal Fault

371

High System Disch Pressure Sensor Warning

311

VSD Board NovRAM Failure

372

Low Suction Temp Sensor Warning

313

Harmonic Filter Serial Communication

373

High Suction Temp Sensor Warning

314

Harmonic Filter Input Frequency Out of Range

374

Low Disch Temp Sensor Warning

331

VSD High Phase A Inverter Baseplate Temp

375

High Disch Temp Sensor Warning

332

VSD Low Phase A Inverter Baseplate Temp

376

Low Oil Temp Compressor Sensor Warning

333

High Discharge Pressure Shutdown

377

High Oil Temp Compressor Sensor Warning

334

High Discharge Pressure Warning

378

Low Oil Separator Temp Sensor Warning

335

Process Stopped See Event Log

379

High Oil Separator Temp Sensor Warning

336

High Process Entering Temp Shutdown

380

Low Intermediate Temp Sensor Warning

337

High Process Entering Temp Warning

381

High Intermediate Temp Sensor Warning

338

Low Process Entering Temp Shutdown

382

Low Process Leaving Temp Sensor Warning

339

Low Process Entering Temp Warning

383

High Process Leaving Temp Sensor Warning

340

High Motor Temp Warning - Shaft Side

384

Low Process Entering Temp Sensor Warning

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 107

WARNING/SHUTDOWN MESSAGE CODES (Continued)


385

High Process Entering Temp Sensor Warning

429

High Auxiliary Analog Input #9 Sensor Warning

386

Low External Temp Sensor Warning

430

Low Auxiliary Analog Input #10 Sensor Warning

387

High External Temp Sensor Warning

431

High Auxiliary Analog Input #10 Sensor Warning

388

Low Refrigerant Liquid Temp Sensor Warning

432

Low Auxiliary Analog Input #11 Sensor Warning

389

High Refrigerant Liquid Temp Sensor Warning

433

High Auxiliary Analog Input #11 Sensor Warning

390

Low Inlet Condenser Temp Sensor Warning

434

Low Auxiliary Analog Input #12 Sensor Warning

391

High Inlet Condenser Temp Sensor Warning

435

High Auxiliary Analog Input #12 Sensor Warning

392

Low Outlet Condenser Temp Sensor Warning

436

Low Auxiliary Analog Input #13 Sensor Warning

393

High Outlet Condenser Temp Sensor Warning

437

High Auxiliary Analog Input #13 Sensor Warning

394

Low Economizer Gas Temp Sensor Warning

438

Low Auxiliary Analog Input #14 Sensor Warning

395

High Economizer Gas Temp Sensor Warning

439

High Auxiliary Analog Input #14 Sensor Warning

396

Low Motor Cooling Media Temp Sensor Warning

440

Low Auxiliary Analog Input #15 Sensor Warning

397

High Motor Cooling Media Temp Sensor Warning

441

High Auxiliary Analog Input #15 Sensor Warning

398

Low Seq Temp Cont Feedback Sensor Warning

442

Low Auxiliary Analog Input #16 Sensor Warning

399

Low Seq Temp Cont Feedback Sensor Warning

443

High Auxiliary Analog Input #16 Sensor Warning

400

Low Thermistor In Motor Sensor Warning

444

Low Auxiliary Analog Input #17 Sensor Warning

401

High Thermistor In Motor Sensor Warning

445

High Auxiliary Analog Input #17 Sensor Warning

402

Low Ext Setpt/Ext Inp Sig Sensor Warning

446

Low Auxiliary Analog Input #18 Sensor Warning

403

High Ext Setpt/Ext Inp Sig Sensor Warning

447

High Auxiliary Analog Input #18 Sensor Warning

404

Low Motor Current Sensor Warning

448

Low Auxiliary Analog Input #19 Sensor Warning

405

High Motor Current Sensor Warning

449

High Auxiliary Analog Input #19 Sensor Warning

406

Low RPM Sensor Warning

450

Low Auxiliary Analog Input #20 Sensor Warning

407

High RPM Sensor Warning

451

High Auxiliary Analog Input #20 Sensor Warning

408

Low Kw Monitoring Sensor Warning

452

Low Manifold Pressure Sensor Warning

409

High Kw Monitoring Sensor Warning

453

High Manifold Pressure Sensor Warning

410

Low Condenser Valve Feedback Sensor Warning

454

Low Rem Capacity Position Sensor Warning

411

High Condenser Valve Feedback Sensor Warning

455

High Rem Capacity Position Sensor Warning

412

Low Auxiliary Analog Input #1 Sensor Warning

456

Low Liquid Level Sensor Warning

413

High Auxiliary Analog Input #1 Sensor Warning

457

High Liquid Level Sensor Warning

414

Low Auxiliary Analog Input #2 Sensor Warning

458

High Process Leaving Temp Shutdown

415

High Auxiliary Analog Input #2 Sensor Warning

459

High Process Leaving Temp Warning

416

Low Auxiliary Analog Input #3 Sensor Warning

460

Low Process Leaving Temp Shutdown

417

High Auxiliary Analog Input #3 Sensor Warning

461

Low Process Leaving Temp Warning

418

Low Auxiliary Analog Input #4 Sensor Warning

462

Coalescer Filter Differential Warning

419

High Auxiliary Analog Input #4 Sensor Warning

463

Condensing Water In Separator Warning (Off)

420

Low Auxiliary Analog Input #5 Sensor Warning

464

Condensing Water In Separator Warning (Run-

421

High Auxiliary Analog Input #5 Sensor Warning

422

Low Auxiliary Analog Input #6 Sensor Warning

465

Low Starting Oil Pressure Shutdown (for shaft

423

High Auxiliary Analog Input #6 Sensor Warning

424

Low Auxiliary Analog Input #7 Sensor Warning

466

425

High Auxiliary Analog Input #7 Sensor Warning

467

Remote Stop Shutdown (RCIS only)

426

Low Auxiliary Analog Input #8 Sensor Warning

468

Vyper Fault Limit Reached Shutdown

427

High Auxiliary Analog Input #8 Sensor Warning

428

Low Auxiliary Analog Input #9 Sensor Warning

ning)
aux. pump type)
Manual Stop Shutdown (RSCI only)

090.020-CS (JUNE 11)


Page 108

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SECTION 8
Q5 CONTROLLER

090.020-CS (JUNE 11)


Page 109

090.020-CS (JUNE 11)


Page 110

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

Q5 CONTROLLER
MAIN BOARD HISTORY AND IDENTIFICATION

ure the Quantum 5 for specific applications.

The processor board shown on this page is known as


the Q5 board, and it is based on the Pentium microprocessor platform. The operating software that this
board runs is known as Quantum LX software. This
software displays graphic information and data on the
LCD screen in a format that is similar to the way a
Windows desktop computer screen displays a Web
browser (the Internet).
The Q5 board can be identified by the presence of a
large aluminum heat sink located on the board. Adjacent to the processor board, is an Interface board
which allows the user to attach local communications
connections via the four orange connectors (RS-422
and RS-485 ports).
There are also a number of jumpers present on both
the Q5 and the Interface board. These jumpers MAY
need to be modified by qualified personnel to config-

The Q5 utilizes Flash Card technology. There is a Flash


Card socket located on the under side of this main
board. The Q5 board has the LX Operating System
pre-loaded at the factory, so this Flash Card feature
will primarily be utilized for future program updates.
The information that follows will primarily describe
the jumper configuration for communications settings, as well as wiring diagrams for the different
types of communications that are possible with the
Q5.

Q5 COMMUNICATIONS CONNECTOR LOCATIONS


The following pictorial shows the customer connection points for both serial communications and the
Ethernet connection. Note that COMM-4 is reserved
for communications to the installed I/O boards, and
cannot be used for customer applications.

Ethernet

COMM-4
(Reserved)

COMM-3
(RS-485)

COMM-2
(RS-422)

COMM-1
(RS-422)

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

Q5 SERIAL COMMUNICATIONS HARDWARE

COM-1 AND COM-2 DESCRIPTION

Q5 GENERAL DESCRIPTION
User connections for serial communications to
and from the Q5 are located on the Interface
board, and can use RS-422 and/or RS-485 hardware protocol. These hardware protocols can be
connected via Com-3 and Com-4 for RS-485,
and Com-1 and Com-2 for RS-422.
As mentioned in the previous paragraph, the
user connections for the serial communications
portion of the Q5 controller consists of an Interface board, mounted below and to the right of
the main controller. In addition to external forms
of serial communication (to be discussed shortly), the keypad also connects here:
COM-3
(RS-485)

COM-4
(RS-485)

COM-2
(RS-422)
COM-1
(RS-422)

Keypad

Communications Ports on the Q5 Interface


Board

090.020-CS (JUNE 11)


Page 111

The board pictured on this page has two RS-422 serial communications ports, labeled P10 (Com-1) and
P11 (Com-2). They can be used for external communications to the outside world.
COM-3 DESCRIPTION
Com-3 is labeled as P16 and is used for RS-485 hardware protocol, and can be used in addition to any of
the other communications ports that may be being
used.
COM-4 DESCRIPTION
Com-4 (RS-485) is dedicated to providing communications to the DIgital and Analog boards, and will be
explained in the section entitled Com-4 Description.

090.020-CS (JUNE 11)


Page 112

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

Q5 SERIAL COMMUNICATIONS PORT WIRING

served for I/O board communications. Refer to


the tables in this section for the specifics on the
jumper settings RS-422/485:

GENERAL NOTE
The information that is presented here and on
the following pages, refers to the Interface board
and not the Q5 board. The Interface board was
developed to make customer connections to the
processor easier, as the Q5 use connections that
are too small and delicate to easily utilize in the
field.

COMM-4
(P17)

COMM-3
(P16)

RS-485
(RESERVED)

RS-485

-TX/-RX
GND

+TX/+RX

COMM-2
(P11)

RS-232 WIRING AND JUMPERS

RS-422 RS-485
GND
N/C
-RX
N/C
+RX
GND
-TX
-TX/-RX
+TX
+TX/+RX

With the introduction of the Q5/Interface board,


customer connections to RS-232 have been
eliminated. If RS-232 communications IS required, these signals may be converted to RS422/485, and the appropriate available port(s)
utilized.
RS-422/485 WIRING AND JUMPERS
All four Interface board serial communications
ports are capable of RS-485, and COMM-1 (P10)
and COMM-2 (P11) can additionally be configred
as either RS-422 or RS-485.
The following table describes the Interface board
RS-422 connector pinouts and their associated
communications signals:

COMM-1
(P10)
RS-422/485 Connectors, Jumpers and LED Location

RS-422/485 (COMM-1, & COMM-2, P11) Board Jumpers

RS-422 Signal Wiring


Connector
Pin #

RS-422 RS-485
GND
N/C
-RX
N/C
+RX
GND
-TX
-TX/-RX
+TX
+TX/+RX

Jumper Title

Signal
COMM-1
(P10)

COMM-2
(P11)

GND

GND

TX+

TX+

TX-

TX-

RX+

RX+

RX-

RX-

RS-485 Signal Wiring


Signal
Connector COMM COMM COMM COMM
Pin #
1
2
3
4
(P10)
(P11)
(P17)
(P16)
3

GND

+TX/+RX

-TX/-RX

The following pictorial shows a cutaway view


of the Interface board, as well as the jumpers,
LEDs and signal pinouts to allow the end user
to communicate to COMM-1 (P10) and COMM2 (P11) using RS-422/485 protocol, and to use
COMM-3 (P16) to communicate via RS-485.
NOTE: COMM-3 and COMM-4 do not have any
associated jumpers, and COMM-4 (P17) is re-

COMM-1 COMM-2
(P10)
(P11)

J1

Function

Jumper Setting

RS-422
(4-Wire)
Default

3
2
1

1-2
Closed

RS-485
(2-Wire)

3
2
1

2-3
Closed

J7

J2

J13

Pull Down
Default

1 Pin
Only

J3

J16

Pull Up
Default

1 Pin
Only

J4

J17

RS-422
Default

1 Pin
Only

J5

J18

Pull Down
Default

1 Pin
Only

J6

J22

Pull Up
Default

1 Pin
Only

NOTE: The triangle symbol (


nectors.

) denotes Pin 1 on con-

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SERIAL COMMUNICATIONS TROUBLESHOOTING


WIRING NOTE: See the chapter entitled Serial Communications Port Wiring, for the pictorials and tables referred to in the following paragraphs. Always
ensure that the wiring matches these pictorials before proceeding.
JUMPER NOTE: Some of the jumpers in the previous tables may need to be modified for RS-422/485
to ensure optimum communications performance.
Typically, the termination jumper should be installed
in the last Quantum in the communications daisy
chain only.
TROUBLESHOOTING RS-232
The Q5 does not use RS-232.
TROUBLESHOOTING RS-422
COMM-1 (P10)
COMM-1 may be used for either RS-422 or
RS-485, depending on the setting of jumper
J1. If pins 1-2 are shorted (closed) on J1,
then RS-422 is selected.
Notice in the figure entitled RS-422/485
Connectors, Jumpers and LED Location, there are six jumpers associated with
COMM-1. Refer to the table entitled RS422/485 (COMM-1, P10 & COMM-2, P11)
Board Jumpers for the function of each of
the jumpers associated with COMM-1. Notice also the two LED indicators that are
pointed out. D8 LED will flash each time that
the Quantum transmits (TX) data. D9 LED
will flash each time that data is received
(RX).
If communications cannot be established using COMM-1, then note the status of these
two LEDs (D8 and D9). If D8 is constantly lit,
it may indicate an external wiring issue (TX
and RX possibly swapped). Also verify the
position of J1, and ensure that it is set for
pins 1-2 closed.
Also verify that the proper Panel ID, Baud
rate, data bits, and protocol has been setup
at the Quantum, and matches that of the
initiating device (see the section entitled
COMMUNICATIONS SETUP for further details).
COMM-2 (P11)
COMM-2 may be used for either RS-422 or
RS-485, depending on the setting of jumper
J7. If pins 1-2 are shorted (closed) on J7,
then RS-422 is selected.
Notice in the figure entitled RS-422/485

090.020-CS (JUNE 11)


Page 113

Connectors, Jumpers and LED Location, there are six jumpers associated with
COMM-2. Refer to the table entitled RS422/485 (COMM-1, P10 & COMM-2, P11)
Board Jumpers for the function of each of
the jumpers associated with COMM-2. Notice also the two LED indicators that are
pointed out. D26 LED will flash each time
that the Quantum transmits (TX) data. D25
LED will flash each time that data is received
(RX).
If communications cannot be established using COMM-2, then note the status of these
two LEDs (D25 and D26). If D25 is constantly
lit, it may indicate an external wiring issue
(TX and RX possibly swapped). Also verify
the position of J7, and ensure that it is set
for pins 1-2 closed.
Also verify that the proper Panel ID, Baud
rate, data bits, and protocol has been setup
at the Quantum, and matches that of the
initiating device (see the section entitled
COMMUNICATIONS SETUP for further details).
TROUBLESHOOTING RS-485
COMM-1 (P10)
COMM-1 may be used for either RS-422 or
RS-485, depending on the setting of jumper
J1. If pins 2-3 are shorted (closed) on J1,
then RS-485 is selected.
Notice in the figure entitled RS-422/485
Connectors, Jumpers and LED Location, there are six jumpers associated with
COMM-1. Refer to the table entitled RS422/485 (COMM-1, P10 & COMM-2, P11)
Board Jumpers for the function of each of
the jumpers associated with COMM-1. Notice also the two LED indicators that are
pointed out. D8 LED will flash each time that
the Quantum transmits (TX) data. D9 LED
will flash each time that data is received
(RX).
If communications cannot be established using COMM-1, then note the status of these
two LEDs (D8 and D9). If D8 is constantly lit,
it may indicate an external wiring issue (TX
and RX possibly swapped). Also verify the
position of J1, and ensure that it is set for
pins 1-2 closed.
Also verify that the proper Panel ID, Baud
rate, data bits, and protocol has been setup
at the Quantum, and matches that of the
initiating device (see the section entitled
COMMUNICATIONS SETUP for further details).

090.020-CS (JUNE 11)


Page 114

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

COMM-2 (P11)
COMM-2 may be used for either RS-422 or
RS-485, depending on the setting of jumper
J7. If pins 2-3 are shorted (closed) on J7,
then RS-485 is selected.
Notice in the figure entitled RS-422/485
Connectors, Jumpers and LED Location, there are six jumpers associated with
COMM-2. Refer to the table entitled RS422/485 (COMM-1, P10 & COMM-2, P11)
Board Jumpers for the function of each of
the jumpers associated with COMM-2. Notice also the two LED indicators that are
pointed out. D26 LED will flash each time
that the Quantum transmits (TX) data. D25
LED will flash each time that data is received
(RX).
If communications cannot be established using COMM-2, then note the status of these
two LEDs (D25 and D26). If D25 is constantly
lit, it may indicate an external wiring issue
(TX and RX possibly swapped). Also verify
the position of J7, and ensure that it is set
for pins 1-2 closed.
Also verify that the proper Panel ID, Baud
rate, data bits, and protocol has been setup
at the Quantum, and matches that of the
initiating device (see the section entitled
COMMUNICATIONS SETUP for further details).
COMM-3 (P16)
Notice that in the figure entitled RS-422/485
Connectors, Jumpers and LED Location, there are no jumpers associated with
COMM-3. Notice also the two LED indicators
that are pointed out in the figure. D42 LED
will flash each time that the Quantum 5
transmits (TX) data. D43 LED will flash each
time that data is received (RX).
If communications with the Quantum 5
cannot be established using COMM-2, then
note the status of these two LEDs (D42 and
D43). If D43 is constantly lit, it may indicate
an external wiring issue (TX and RX possibly
swapped). If D43 never flashes, then the LX
is not receiving any data. If D43 does flash
each time a data bit is received, but D42
never flashes, this may indicate that the LX
has received a data command, but that the
protocol package is not properly formatted,
and the LX cannot respond.
On the Communications Setup screen, verify that the proper Panel ID, Baud rate, data
bits, and protocol has been setup at the
Quantum LX, and matches that of the ini-

tiating device.
COMM-4 (P17)
NOTE: Although COMM-4 is used for RS485 communications, this port is reserved
for the purpose of communicating to the internal Digital and Analog boards. It can still
be diagnosed with the following procedure.
Notice that in the figure entitled RS-422/485
Connectors, Jumpers and LED Location, there are no jumpers associated with
COMM-4. Notice also the two LED indicators that are pointed out in the figure. D54
LED will flash each time that the Quantum
5 transmits (TX) data. D55 LED will flash
each time that data is received (RX).
If communications with the internal I/O logic boards of the Quantum 5 cannot be established using COMM-4, then note the status of these two LEDs (D54 and D55). If D54
is constantly lit, it may indicate an external
wiring issue (TX and RX possibly swapped).
If D55 never flashes, then the LX is not receiving any data from the I/O boards. If D54
does flash each time a data bit is received,
but D55 never flashes, this may indicate that
the LX has received a data command, but
that the protocol package is not properly
formatted, and the LX cannot respond.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

COMMUNICATIONS DATA LOGGING SCREENS

090.020-CS (JUNE 11)


Page 115

SERVICE ModBus TCP Log

SERVICE Communications Log

ACCESSING:
ACCESSING:

Service

Service

Communications Log

DESCRIPTION: This screen allows the technician to


view the status of all serial communications ports. or
the status of all Modbus TCP communications. Refer
to the section entitled Modbus TCP Log in the Modbus Protocol chapter.
The following user selectable buttons are provided:

[Show
[Show
[Show
[Show

Comm1]
Comm2]
Comm3]
Comm4]

This screen allows the technician to view all of the serial


communications information that the Quantum LX is receiving and transmitting, one port at a time. Simply select
the button at the upper right side of the screen that corresponds to the port that you wish to view. The selected
port name (in this case Comm4) will appear in the upper
left side of the screen.
Each time a new command is sent or received, the screen
will need to be refreshed by selecting the [Show CommX]
button (where X is replaced with the comm port number).
The top line of data is the most recent activity. At the left
of each line, you should see whether the data is IN or OUT
(Receive or Send), and the actual data (in Hexadecimal
format). This information can be used to compare against
the data being sent and received at the other end of the
communications link, to verify proper operation. Refer to
the section on Hyperterminal for some examples of how
this screen may be used.

ModBus TCP Log

DESCRIPTION: This screen allows the technician to


view the status of all Modbus TCP communications.
Refer to the section entitled Modbus TCP Log in the
Modbus Protocol chapter.
The following user selectable button is provided:

[Refresh]

This screen allows the technician to view all of the Modbus TCP communications information that the Quantum
LX is receiving and transmitting.
Each time a new command is sent or received, the screen
will need to be refreshed by selecting the [Refresh] button.
The top line of data is the most recent activity. At the left
of each line, you should see whether the data is IN or OUT
(Receive or Send), and the actual data (in Hexadecimal
format). This information can be used to compare against
the data being sent and received at the other end of the
communications link, to verify proper operation.
NOTE: Refer to the section entitled Modbus TCP Log in the
Modbus Protocol chapter for additional information.

090.020-CS (JUNE 11)


Page 116

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SECTION 9
Q4 CONTROLLER

090.020-CS (JUNE 11)


Page 117

090.020-CS (JUNE 11)


Page 118

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUANTUM 4 CONTROLLER
MAIN BOARD HISTORY AND IDENTIFICATION

need to be modified by qualified personnel to configure the Quantum 4 for specific applications.

The processor board shown on this page is known as


the Quantum 4 board, and it is based on the Pentium microprocessor platform. The operating software that this board runs is known as Quantum LX
software. This software displays graphic information
and data on the LCD screen in a format that is similar
to the way a Windows desktop computer screen
displays a Web browser (the Internet).

The Quantum 4 utilizes Flash Card technology, as


did the Quantum 3. There is a Flash Card socket
located on the under side of this main board. The
Quantum 4 board has the LX Operating System
pre-loaded at the factory, so this Flash Card feature
will primarily be utilized for future program updates.
When calling Frick Company for service or help, it
will greatly assist us if the type of board is known,
either Quantum 1, 2, 3 or 4. Additionally, Frick
will request the Sales Order number, and the Operating System version number (this can be found on
the About screen). The more information available
at the time of the call, the better able we will be to
assist you.

The Quantum 4 board can be identified by the presence of a daughter board mounted to the main board.
This daughter board is the communications portion
of the Quantum 4, and it can be identified by the
presence of an 8 position DIP switch. There are also
a number of jumpers (or links) present on this smaller
board, as well as three green connectors (RS-232,
RS-422 and RS-485 ports). The jumpers are used to
set up the communications parameters that are listed
on the next page.

The information that follows will primarily describe


the jumper configuration for communications settings, as well as wiring diagrams for the different
types of communications that are possible with the
Quantum 4.

The main board (larger of the two) has a number of


jumpers (or links) also. The links on this board MAY
USB Connector
(Depending on board version, USB could be
located in either of these two places).
PL
9

PL7

PL
12

PL
17

LK1

Com-3
RS-232
Connector

PL8

PL
19

PL
18

PL13

PL
24

LK2

PL1

PL2

COM-1
RS422

4
3
2
1
TB1

A
B

LK
7
LK LK
5 6

LK2
TB2

RS422

3
2
1

COM-2

PL4

RS-

0
1
2
3
4
5
6
7

POR
T
80H

COM1

D4 D5 D7 D8 D10 D1 D1 D13
1 2

(TX)

LK
10

D3

LK12

PW
R

LK11

FL
AS
H

PL16

LK10
LK9
LK8
ON

76
54
32
1

PL14

PL10

PL6

Com-1
(TB1)
RS-422/485
Connector

SW1

COM1

LK
9

D2

LK
8
LK
7

LK16
A

COM2
(TX)
D1

LK
6
LK
5

D6

LK11
B A

LK
4
RS- LK
LK1 3

LK16 selects
between
RS-422 and
RS-485 for
Com-1 (TB1).
LK11 Selects
between using
RS-422/485 on
Com-2 (TB2)
OR
RS-232 on
Com-2 (TB3)

PL2

COM2

SU
SP

LK17
PL4

KB

LK17 selects
between
RS-422 and
RS-485 for
Com-2 (TB2).

D8

PL3
TB3

Com-2
(TB2)
RS-422/485
Connector

COM-2

RS-232
3

Flash Card Socket


(Located under board)

LK4

A B
LK3

CAT-5 Ethernet
Connector

PL3
PL1

Com-2
(TB3)
RS-232
Connector
PL
11
PL1
5

PL5

Keypad

Quantum 4 Communications Jumpers, connectors and LED locations

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

QUANTUM 4 SERIAL COMMUNICATIONS


HARDWARE
QUANTUM 4 GENERAL DESCRIPTION
Serial communications to and from the Quantum 4 can use RS-232, RS-422 and/or RS-485
hardware protocol. These three hardware protocols can be connected via Com-1 and Com-2 for
RS-422/485, and Com-2 for RS-232. The reason
that Com-2 can be either RS-232 or RS-422/485
will be explained in the section entitled Com-1
and Com-2 Description.

090.020-CS (JUNE 11)


Page 119

COM-1 AND COM-2 DESCRIPTION


The board pictured in the previous column actually has three serial communications ports
(labeled as TB1, TB2 and TB3). TB1 is known as
Com-1, and is reserved solely for RS-422/485
communications. It can be used for external
communications to the outside world.
TB2 is known as Com-2. However, TB3 is also
known as Com-2. The difference here is that TB2
is for RS-422/485 whereas TB3 is for RS-232.
TB2 can be used in the same manner as TB1.

The Com-1 and Com-2 serial communications


portion of the Quantum 4 controller consists of
a daughter board, mounted to the main controller. In addition to external forms of serial communication (to be discussed shortly), the keypad
also connects here.

When TB2 (Com-2) is setup to be used for RS422/485, then TB3 cannot be used for RS-232,
and vice-versa. The reason for this is that there
is a jumper (LK11) that needs to be properly set
that will tell the controller which of the two ports
will be used (either TB2 as RS-422/285 OR TB3
as RS-232).

Com-3 is another serial port (RS-485) that is


dedicated to providing communications to the
DIgital and Analog boards. The location of Com3 is on the main processor board and will be explained in the section entitled Com-3 Description.

RS-422/RS-485 signals cannot be connected directly to an RS-232 device. These signals must
first be conditioned (converted). See the section
entitled Converting an RS-232 Signal to RS422/485 for details.

RS-232 signals cannot be connected directly to


either an RS-422 or RS-485 device. These signals must first be conditioned (converted). See
the section entitled Converting an RS-232 Signal to RS-422/485 for details.

PL6
Com-3
RS-485
TB1
Com-1
RS-422/485
TB2
Com-2
RS-422/485
TB3
Com-2
RS-232

Communications Ports on the Quantum 4


Daughter Board

COM-3 DESCRIPTION
Com-3 (PL6) is used for RS-232 hardware protocol only, and can be used in addition to any
of the other communications ports that may be
being used. So it is possible to have two RS-232
ports active (Com-2 AND Com-3) at the same
time, as well as Com-1 for RS-422/485.

090.020-CS (JUNE 11)


Page 120

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SERIAL COMMUNICATIONS PORT WIRING


RS-232 WIRING AND JUMPERS
COM-2 (TB3)

PORT
80H

The following pictorial shows the communications board, as well as the jumpers, LEDs and
signal pinouts to allow the end user to communicate to Com-3 (PL6) using RS-232 protocol.
Refer to the table entitled Com-3, PL6 Communications Signals for the specifics on the jumper settings and wiring convention for RS-232.
NOTE: There are NO jumper settings associated
with this connector (Com-3).
9

PC or PLC
9-Pin
D-Connector

6
1

COM

ON

TX

RX

SW1

D D D D D

D3

COM-1

The following pictorial shows the communications board, as well as the jumpers, LEDs
and signal pinouts to allow the end user to
communicate to Com-2 (TB3) using RS-232
protocol. Refer to the tables in this section
for the specifics on the jumper settings and
wiring convention for RS-232.

COM-3 (PL6)

12345678

LK10

PL2

D2
LK8

D6

LK16

TB1

LK11

LK7

LK2

TB2

B A

LK6

RS422

PL6

PL10

PL14

RS-422

PL1

A
B
LK5 LK6

PL3
COM-2

COM

RX

LK16

B A

2
1

PL4

TX

COM2 (TX)
D1

LK6

TB2

RS-232 TB3
3-Pin Connector

COM2 (RX)
D6
LK11

LK7

LK2
LK7

123456 78

A B

TB1

D8

SW1

PL2
D2

LK8

RS-232

PWR

SUSP

ON

LK9

LK3

TB3

LK11

D3

LK10

KB

LK1

PL16

LK10
LK9
LK8
0

COM-1
LK17

COM-2

PL19
LK12

FLASH

A B

LK5
LK4

PL18

LK2

PL1

Transmit Data (TX)


LED

PL24

PL13

PL8

Jumper

D1

4
3

Receive Data
(RX) LED

PL17

PL12

LK1

RS422

PL9

PL7

LK9

RS422
LK1

A B

LK5

LK17

LK4

TB3

PL4

KB

LK3

D8

PL3

RS-232

PL1
PL3

COM-2

RX

2
6

3
7

COM

TX

8 9

PC or PLC
9-Pin
D-Connector

RS-232 Com-2 (TB3) Communications Wiring

RS-232 Com-2, TB3 Communications Board


Jumpers
LINK POSITION

FUNCTION

RS-232 for COM2 (TB3)


A*
B
RS-422 for COM2 (TB2)
* Standard Setting
LK11

RS-232 Com-2, TB3 Communications Signals


TB3 Connector Pin #

Signal

1
2
3

Transmit Data (TX)


Received Data (RX)
Ground (COM)

LK4
LK3

A B

PL11
PL15

PL5

RS-232 Com-3 (PL6) Wiring To 9-Pin D-Connector

RS-232 Com-3, PL6 Communications Signals


PL6 Connector
Pin #

Signal

Received Data (RX)

Transmit Data (TX)

Ground (COM)

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
RS-422 WIRING AND JUMPERS

090.020-CS (JUNE 11)


Page 121

COM-2 (TB2)

The following table describes the RS-422 connector pinouts and their associated communications signals:

TB1 Connector Pin #

Signal

TX+

TX-

RX+

RX-

PORT
80H

4
LK9

PL2

D2

COM-1 (TB1)

LK8

D6

LK16

A B

TB1

The following pictorial shows the communications board, as well as the jumpers, LEDs
and signal pinouts to allow the end user to
communicate to Com-1 (TB1) using RS-422
protocol. Refer to the tables in this section
for the specifics on the jumper settings and
wiring convention for RS-422:

TB2

+TX
-TX
+RX
-RX

LK5
LK4

LK1

LK8

Com-1 (TB1)
RS-422
Connector

RS-

D2

LK16

A B

TB1
LK2

PL1
TB3

LINK POSITION

D1

Jumpers
A

LK5

LK17

COM-2

LK1

KB

LK3

RS-422

LK 3

In
Out*

Pull down COM2


No pull down

RS-422 (Rx-)

LK 4

In
Out*

Pull up COM2
No pull up

RS-422 (Rx+)

LK 5

In
Out*

Pull down COM2


No pull down

RS-422 (Tx-)

LK 6

In
Out*

Pull up COM2
No pull up

RS-422 (Tx+)

LK
11

A
B*

Select RS-232 for COM2 (TB3)


Select RS-422 for COM2 (TB2)

LK
17

A*

COM2 RS-422 (TB2)

PL1
TB3
PL3
3

RS-422 Com-1 (TB1) Connector, Jumpers and LED Location

RS-422 (TB1) Board Jumpers


LINK

POSITION

FUNCTION

LK2

In
Out*

Terminate COM1
No termination

RS-422

LK7

In
Out*

Pull down COM1


No pull down

RS-422
(-RX)

LK8

In
Out*

Pull up COM1
No pull up

RS-422
(+RX)

LK9

In
Out*

Pull down COM1


No pull down

RS-422
(-TX)

LK10

In
Out*

Pull up COM1
No pull up

RS-422
(+TX)

A*
COM1 RS-422 (TB1)
B
COM1 RS-485 (TB1)
* Standard Setting

LK16

FUNCTION
Terminate COM2
No termination

D8

COM-2

In
Out*

LK4

LK 1

4
3

RS-422 (TB2) Board Jumpers

PL2

B A

LK6

Jumpers
KB

LK3

RS-422 Com-2 (TB2) Connector, Jumpers and LED


Location

LK11

LK7

TB2

LK17

PL3

SW1

Transmit Data
(TX) LED
Receive Data
(RX)
LED
D6

LK9

A B

D8

Com-2 (TB2) RS422 Connector

1 2 34 5 6 78

LK10

Transmit Data (TX)


LED

RS-

COM-2

ON

D D D D D

D3

D1

Receive Data
(RX) LED

B A

LK6

COM-2

+TX
-TX
+RX
-RX

LK11

LK7

PORT
80H

SW1
1 2 34 5 6 78

LK10

COM-1

ON

D D D LK2 D

D3

COM-1

RS-422 (TB1) Signal Wiring

The following pictorial shows the communications board, as well as the jumpers, LEDs
and signal pinouts to allow the end user to
communicate to Com-2 (TB2) using RS-422
protocol. Refer to the tables in this section
for the specifics on the jumper settings and
wiring convention for RS-422:

B
COM2 RS-485 (TB2)
* Standard Setting

090.020-CS (JUNE 11)


Page 122

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

RS-485 WIRING AND JUMPERS

COM-2 (TB2)

RS-422 (TB1) Communications Signal Wiring


TB1 Connector Pin #

Signal

+TX / +RX

-TX / -RX

PORT
80H

COM-1 (TB1)

4
LK9

3
LK8

+TX/+RX
-TX/-RX
Com-1 (TB1) RS485 Connector

LK2

TB2

LK8

RS
RSTB1
485
LK2

D2
LK16

A B

TB2

LK5

RS
RS485
LK1

PL2

RS-485 (TB2) Communications Board Jumpers

LK4

KB

LK3

D8

LINK

POSITION

LK 1

In
Out*

Terminate COM2
No termination

RS-485

LK 3

In
Out*

Pull down COM2


No pull down

RS-485
(-TX /-RX)

LK 4

In
Out*

Pull up COM2
No pull up

RS-485
(+TX /+RX)

LK 11

A
B*

Select RS-232 for COM2 (TB3)

LK 17

A
B*

COM2 RS-422 (TB2)

PL1
TB3
PL3
3

PL3
COM-2

RS-485 Com-2 (TB2) Connector, Jumpers and LED Location

LK17

COM-2

Jumpers
KB

LK3

PL1

Jumpers
A

LK5

LK1

LK17

D1

COM-2

Transmit Data (TX)


LED

A B

LK4

Com-2 (TB2) RS485 Connector

D1

D8

B A

LK6

B A

LK6

+TX/+RX
-TX/-RX

Receive Data
(RX) LED

TB3

LK11

LK7

LK11

LK7

SW1

Transmit Data (TX)


LED
Receive Data
(RX)
LED
D6

LK9

A B

TB1

1 2 34 5 6 78

D6

LK16

ON

D D D D D

D3
LK10

PL2

D2

COM-2
PORT
80H

SW1
1 2 34 5 6 78

LK10

The following pictorial shows the communications board, as well as the jumpers, LEDs
and signal pinouts to allow the end user to
communicate to Com-1 (TB1) using RS-485
protocol. Refer to the tables on this page
for the specifics on the jumper settings and
wiring convention for RS-485:

COM-1

ON

D D D D D

D3

COM-1

The following pictorial shows the communications board, as well as the jumpers, LEDs
and signal pinouts to allow the end user to
communicate to Com-2 (TB2) using RS-485
protocol. Refer to the tables in this section
for the specifics on the jumper settings and
wiring convention for RS-485:
0

The following table describes the RS-485 connector


pinouts and their associated communications signals:

RS-485 Com-1 (TB1) Connector, Jumpers and LED Location

RS-485 (TB1) Communications Board Jumpers


LINK

POSITION

FUNCTION

LK2

In
Out*

Terminate COM1
No termination

RS-485

LK7

In
Out*

Pull down COM1


No pull down

RS-485
(-TX / -RX)

LK8

In
Out*

Pull up COM1
No pull up

RS-485
(+TX /
+RX)

LK16

A
B*
* Standard Setting

COM1 RS-422 (TB1)


COM1 RS-485 (TB1)

* Standard Setting

FUNCTION

Select RS-485 for COM2 (TB2)


COM2 RS-485 (TB2)

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SERIAL COMMUNICATIONS TROUBLESHOOTING


WIRING NOTE: See the chapter entitled Serial Communications Port Wiring, for the pictorials and tables referred to in the following paragraphs. Always
ensure that the wiring matches these pictorials before proceeding.
JUMPER NOTE: Some of the jumpers in the previous tables may need to be modified for RS-422/485
to ensure optimum communications performance.
Typically, the termination jumper should be installed
in the last Quantum in the communications daisy
chain only.
TROUBLESHOOTING RS-232
Com-2 (TB3)
Notice in the figure entitled RS-232 Com2 (TB3) Communications Wiring, the only
jumper associated with TB3 Com-2 is jumper LK11. LK11 must be set to the A position.
Notice the LED indicators that are pointed
out. D4 LED will flash each time that the
Quantum transmits (TX) data. D6 LED will
flash each time that data is received (RX).
If communications cannot be established
using TB3, then note the status of these
two LEDs (D4 and D6). If D6 is constantly
lit, it may indicate an external wiring issue
(TX and RX possibly swapped). Also verify
the position of LK11, and ensure that it is in
position A.
Also verify that the proper Panel ID, Baud
rate, data bits, and protocol matches that of
the initiating device (see the section entitled
COMMUNICATIONS SETUP for further details).
Com-3 (PL6)
Notice in the figure entitled RS-232 Com3 (PL6) Wiring to 9-Pin D-Connector, there
are no jumpers or LEDs associated with PL6
Com-3.
If communications cannot be established
using PL6, verify that the wiring is per the
figure when wired direct from a remote RS232 port.
Also verify that the proper Panel ID, Baud
rate, data bits, and protocol matches that of
the initiating device (see the section entitled
COMMUNICATIONS SETUP for further details).

090.020-CS (JUNE 11)


Page 123

TROUBLESHOOTING RS-422
Com-1 (TB1)
Notice that in the table entitled RS-422
Com-1 (TB1) Board Jumpers that there are
six jumpers associated with TB1. Note: LK11
must be set to position B, and LK17 must be
set to position A. Notice also the two LED
indicators that are in the figure. D3 LED will
flash each time that the Quantum 4 transmits (TX) data. D2 LED will flash each time
that data is received (RX).
If communications with the Quantum 4
cannot be established using TB1, then note
the status of these two LEDs (D2 and D3).
If D2 is constantly lit, it may indicate an
external wiring issue (TX and RX possibly
swapped). If D2 never flashes, then the LX
is not receiving any data. If D2 does flash
each time a data bit is received, but D3
never flashes, this may indicate that the LX
has received a data command, but that the
protocol package is not properly formatted,
and the LX cannot respond.
On the Communications Setup screen,
verify that the proper Panel ID, Baud rate,
data bits, and protocol matches that of the
initiating device.
Com-2 (TB2)
Notice that in the table entitled RS-422
Com-2 (TB2) Board Jumpers, there are
seven jumpers associated with TB2. Note:
LK11 must be set to position B, and LK17
must be set to position A. Notice also the
two LED indicators that are pointed out in
the figure. D1 LED will flash each time that
the Quantum 4 transmits (TX) data. D6
LED will flash each time that data is received
(RX).
If communications with the Quantum 4
cannot be established using TB2, then note
the status of these two LEDs (D1 and D6).
If D1 is constantly lit, it may indicate an
external wiring issue (TX and RX possibly
swapped). If D6 never flashes, then the LX
is not receiving any data. If D6 does flash
each time a data bit is received, but D1
never flashes, this may indicate that the LX
has received a data command, but that the
protocol package is not properly formatted,
and the LX cannot respond.
On the Communications Setup screen,
verify that the proper Panel ID, Baud rate,
data bits, and protocol has been setup, and
matches that of the initiating device.

090.020-CS (JUNE 11)


Page 124

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

TROUBLESHOOTING RS-485
Com-1 (TB1)
Notice that in the figure entitled RS-485 Com-1
(TB1) Connector, Jumpers & LED Location, there
are seven jumpers associated with TB1. Refer to
the table entitled RS-485 (TB1) Board Jumpers
for the function of each of these jumpers. Note:
LK11 must be set to position B, and LK17 must be
set to position A. Notice also the two LED indicators that are pointed out in the figure. D3 LED will
flash each time that the Quantum 4 transmits
(TX) data. D2 LED will flash each time that data
is received (RX).
If communications with the Quantum 4 cannot
be established using TB1, then note the status
of these two LEDs (D2 and D3). If D2 is constantly lit, it may indicate an external wiring issue (TX and RX possibly swapped). If D2 never
flashes, then the LX is not receiving any data. If
D2 flashes each time a data bit is received, but
D3 never flashes, this may indicate that the LX
has received a data command, but that the protocol package is not properly formatted, and the
LX cannot respond.
On the Communications Setup screen, verify that
the proper Panel ID, Baud rate, data bits, and
protocol matches that of the initiating device.

Com-2 (TB2)
Notice that in the figure entitled RS-485 Com-2
(TB2) Connector, Jumpers & LED Location, there
are seven jumpers associated with TB2. Refer to
table entitled RS-485 (TB2) Board Jumpers for
the function of each of these jumpers. Note: LK11
must be set to position B, and LK17 must be set
to position A. Notice also the two LED indicators
that are pointed out in the figure. D1 LED will
flash each time that the Quantum 4 transmits
(TX) data. D6 LED will flash each time that data
is received (RX).
If communications with the Quantum 4 cannot
be established using TB2, then note the status of
these two LEDs (D1 and D6). If D1 is constantly
lit, it may indicate an external wiring issue (TX
and RX possibly swapped). If D6 never flashes,
then the LX is not receiving any data. If D6 does
flash each time a data bit is received, but D1
never flashes, this may indicate that the LX has
received a data command, but that the protocol
package is not properly formatted, and the LX
cannot respond.
On the Communications Setup screen, verify that
the proper Panel ID, Baud rate, data bits, and
protocol matches that of the initiating device.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

COMMUNICATIONS DATA LOGGING SCREENS

090.020-CS (JUNE 11)


Page 125

SERVICE ModBus TCP Log

SERVICE Communications Log

ACCESSING:
ACCESSING:

Service

Service

Communications Log

DESCRIPTION: This screen allows the technician to


view the status of all serial communications ports. or
the status of all Modbus TCP communications. Refer
to the section entitled Modbus TCP Log in the Modbus Protocol chapter.
The following user selectable buttons are provided:

[Show
[Show
[Show
[Show

Comm1]
Comm2]
Comm3]
Comm4]

This screen allows the technician to view all of the serial


communications information that the Quantum LX is receiving and transmitting, one port at a time. Simply select
the button at the upper right side of the screen that corresponds to the port that you wish to view. The selected
port name (in this case Comm4) will appear in the upper
left side of the screen.
Each time a new command is sent or received, the screen
will need to be refreshed by selecting the [Show CommX]
button (where X is replaced with the comm port number).
The top line of data is the most recent activity. At the left
of each line, you should see whether the data is IN or OUT
(Receive or Send), and the actual data (in Hexadecimal
format). This information can be used to compare against
the data being sent and received at the other end of the
communications link, to verify proper operation. Refer to
the section on Hyperterminal for some examples of how
this screen may be used.

ModBus TCP Log

DESCRIPTION: This screen allows the technician to


view the status of all Modbus TCP communications.
Refer to the section entitled Modbus TCP Log in the
Modbus Protocol chapter.
The following user selectable button is provided:

[Refresh]

This screen allows the technician to view all of the Modbus TCP communications information that the Quantum
LX is receiving and transmitting.
Each time a new command is sent or received, the screen
will need to be refreshed by selecting the [Refresh] button.
The top line of data is the most recent activity. At the left
of each line, you should see whether the data is IN or OUT
(Receive or Send), and the actual data (in Hexadecimal
format). This information can be used to compare against
the data being sent and received at the other end of the
communications link, to verify proper operation.
NOTE: Refer to the section entitled Modbus TCP Log in the
Modbus Protocol chapter for additional information.

090.020-CS (JUNE 11)


Page 126

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

COMMUNICATIONS LOOPBACK TEST

HARDWARE SETUP FOR TESTING RS-422

DESCRIPTION
NOTE: Communications Loopback testing is not
yet available for the Q5.

To create the communications loopback harness


for RS-422 testing, use the following example(s):
4-Pin Connector
1

4-Pin Connector
4

-RX
+RX

The purpose of this section is to verify the proper operation of the following communications
ports:

+TX
-TX
+RX
-RX

-TX
+TX
4

Comms 1 (TB1) and 2 (TB2) - RS-422


Comms 1 (TB1) and 2 (TB2) - RS-485
Comms 2 (TB2) and 3 (PL6) RS-232

Quantum 4 RS-422 Test Harness

Set the communications jumpers as follows:

By utilizing a loopback test harness (as shown


on the following pages), the technician has the
ability to locally test the Quantum communications hardware and jumper configuration.

1.
2.
3.
4.

HARDWARE SETUP FOR TESTING RS-232

Set LK11 to position B


Set LK16 to position A
Set LK17 to position A
Plug the RS-422 test harness (as shown
above) into the com ports at TB1 and
TB2 as shown here:

To create the communications loopback harness


for RS-232 testing, use the following example(s):

SW1

10-Pin Connector
1
3
5
7
9

RX

TX
RX
COM

TX
COM

2
4
6
8
10

Quantum 4 RS-232 Test Harness

4
3
2
1
TB1

Set the communications jumpers as follows:


Set LK11 to position A
Plug the RS-232 test harness (as shown
above) into the Com ports at TB3 and
PL6.
PL17

PL12

LK1

PL24

PL13

PL8

PL18

PL19

LK2

PL1

PL6

PL10

PL14

LK12

PL16

LK10
LK9
LK8

LK11

PWR

SUSP

RS-422

LK16

LK5 LK6

COM2 (RX)
D6

A B

TB1

COM2 (TX)
D1

LK6

TB2

LK11

LK7

LK2
LK7

PL2
D2

LK8

A
B

B A

Verify that
LK11 is set to A
position.

4
3
2
1

PL4

RS422
LK1

A B

LK5

LK17

LK4

TB3

PL4

KB

LK3

D8

PL3

SW1

123456 78

LK9

3
2

ON

D3

LK10

FLASH

COM-1

RS-232

PL1
PL3

COM-2

LK4
LK3

A B

PL2
D2

LK8

A B
LK16

LK7

LK2

3
2
1

PL11
PL15

PL5

Com-2 (TB3) & Com-3 (PL6) RS-232 Connector


& Jumper Location

D6

B A
LK11

D1
LK6
LK5

Verify
the jumpers in
these locations

A B
LK17
LK4
LK3

LK1

D8

TB3

COM-2
PL9

PL7

LK9

TB2
4

COM-1
RS-422/RS-485

D3

LK10

COM-2
RS-422/RS-485

3-Pin Connector

Quantum 4 RS-422 Test Configuration

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
HARDWARE SETUP FOR TESTING RS-485
To create the communications loopback harness
for RS-422 testing, use the following example:
4-Pin Connector
1

4-Pin Connector
4
-RX/-TX
+RX/+TX

SOFTWARE SETUP FOR THE COMMUNICATIONS LOOPBACK TEST


On the Communications screen (shown below), ensure that the settings are as follows:

Compressor ID: 0 - 255 (does not matter)

Comm Baud Rate: Does not matter, but all


Comms to be tested must be set the same.

Data Bits: Does not matter, but all Comms to


be tested must be set the same.

Stop Bits: Does not matter, but all Comms to


be tested must be set the same.

Parity: Does not matter, but all Comms to be


tested must be set the same.

Protocol: Set all Comms to be tested to


Frick.

+RX/+TX
-RX/-TX
4

RS-485 Test Harness

Set the communications jumpers as follows:


1.
2.
3.
4.

Set LK11 to position B


Set LK16 to position B
Set LK17 to position B
Plug the RS-485 test harness (as shown
above) into the com ports at TB1 and
TB2 as shown here:
SW1
D3

4
3
2
1
TB1

COM-1
RS-422/RS-485

LK10

LK9

PL2
D2

LK8

A B
LK16

LK7

LK2

2
1

D1
LK6

COM-2
RS-422/RS-485

B A
LK11

TB2
4

D6

LK5

Verify
the jumpers in
these locations

A B
LK17
LK4
LK3

LK1

D8

TB3

COM-2

RS-485 Test Configuration

090.020-CS (JUNE 11)


Page 127

090.020-CS (JUNE 11)


Page 128
PERFORMING
TEST

THE

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
COMMUNICATIONS

LOOPBACK

Note: Session must be set to at least user level 2 to


access this feature.
Upon properly setting up the Communications
screen, press the [Submit Changes] key. Access the
Communications Loop Back Test Screen by pressing
the [Menu] key, then the [Service] key, and finally
the [Communications Loop Back Test] key.
Three buttons appear on this screen:
1.
2.
3.

Test Comm 1 Comm 2


Test Comm 1 Comm 3
Test Comm 2 Comm 3

Ensure that the proper test harness is installed and


the associated jumpers are in their correct positions
for the particular test to be performed.

Pressing the appropriate test key will initiate the test.


A dialog box will appear with one of the following
messages:
1.

Testing - This will appear as the test is running. NOTE: The test occurs so quickly that
It may be possible that the word Testing will
not appear if the test passes.

2.

Passed - If the test passes, the word Passed


will appear.

3.

Failed - If the test does not pass, this will


appear.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

SECTION 10
APPENDICES

090.020-CS (JUNE 11)


Page 129

090.020-CS (JUNE 11)


Page 130

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

APPENDIX A

FRICK SERIAL COMMUNICATIONS CONVERTER MODULE


(Part Number 639B0086H01)

DESCRIPTION
Frick Controls has developed a DIN-rail mountable
communications module for the purpose of converting typical RS-232 serial protocol to either RS-422 or
RS-485 serial protocols. The module will also work
converting RS-422 or RS-485 to RS-232 (bi-directional). Due to the tight mounting restrictions in many
existing control panels, this module provides the ultimate solution for field communications upgrades
or modifications. No drilling is required, and minimal
space is lost. The only requirement is an external
source of 24 volt DC power.

Press the tabs using the thumb and finger, and with
your other hand carefully slide the circuit board out of
the housing. Ensure that proper anti-static guidelines
are followed while handling the circuit board.
The following diagram shows the circuit board:

Module circuit board


For easy reference, the DIP switch position functions
are provided on the board. For the purpose of clarity
however, refer to the following table:
Frick Communications Converter Module
SETTING THE DIPSWITCH
Inside the module is a circuit board which contains a
DIP switch. This switch must be set according to the
necessary protocol parameters that you are trying to
achieve. It is recommended to set or verify the settings of this DIP switch before mounting and wiring
the module. The circuit board must be removed from
its housing in order to access this DIP switch. Each
end of the housing has a small tab, located just below
the bottom most terminal block of each end. Hold the
module as shown in the following pictorial:

MODULE DIP SWITCH SETTINGS


Switch
Position

ON Function

OFF Function

RS-485

RS-422

RS-422

RS-485

RS-422

RS-485

RS-422 Pull up

No pull up

RS-485 Pull up

No pull up

RS-422 Pull down

No pull down

RS-485 Pull down

No pull down

RS-485 termination

No termination

MOUNTING THE MODULE

Locking
Tabs

Disassembling the module

This module can be mounted on the standard din rail


that is available in most control panels.

Find an open area of the din rail (5/8 inch minimum, for the width of the module), and preferably as far away from any inductive loads (relays,
contactors, etc.) as possible.

Module orientation is not critical, however, try


to mount it so that all wiring connections can be
made neatly, and according to any applicable local codes.

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

Catch one end of the DIN rail latch (at the bottom
of the module, under one edge of the DIN rail,
then snap the other latch onto the opposite side
of the DIN rail, as shown below:

090.020-CS (JUNE 11)


Page 131

RS-232 CONNECTIONS (Quantum 4 and earlier only)


Refer to the following figure for the pin connections
showing how to wire a standard 9-Pin RS-232 connector directly to the Frick Communications Converter Module:
RS-232
9-Pin Connector

5
9
4

TX

TX

RX

RX

8
7
6

RS-232 Connections
Refer to the following figure for the pin connections
showing how to wire the Converter Module (converts
from RS-232 to RS-422/485) to the 10-pin Com-3
(PL6) connector on the Quantum:
Module mounted to DIN rail

RS-232 to RS-422/485
Frick Communications Converter
Module Connection
(
)

WIRING THE MODULE


There are twelve total wire terminal points on this
module. Refer to the following table for the pin-out:
Wire terminal connections
Terminal
Position

Module
Power

RS-232

RS-422

-RX

+RX

RS-485

-TX

-RX/-TX

+TX

+RX/+TX

6 (Not Used)
-24 VDC

8 (Not Used)
9

COM
TX
RX

RX
TX
COM

1
3
5
7
9

2
4
6
8
10

Com-3 (PL6) RS-232 Wiring To Frick Communications


Converter Module
RS-422 CONNECTIONS

3 (Not Used)

Quantum LX
RS-232 PL6
10-Pin Connector

Refer to the following figure for the pin connections


showing how to attach a 4-wire RS-422 cable directly
to the Frick Communications Converter Module:

-RX
-TX
+TX
+RX

+24 VDC

RS-422 Connections

10

GND

11

TX

12

RX

Locate a suitable source for the +24 volt DC


power. Using a minimum of 18 AWG stranded wire, connect the MINUS wire to terminal
# 7. Connect the PLUS wire to terminal # 8.

All remaining connections will be based


upon the particular protocols that you have
decided to use. Simply match the SIGNAL
NAME from the source device to match the
SIGANAL NAME of the module. All external
communications wiring must conform with
the Frick Proper Installation of Electronic
Equipment in an Industrial Environment
publication.

RS-485 CONNECTIONS
Although typical RS-485 communications requires a
control signal to change the state of the RX/TX driver
lines to establish handshaking, this board incorporates a smart feature that handles this handshaking
internally, without the user needing to provide it. It is
a true two-wire system. Refer to following figure for
the pin connections showing how to attach a 2-wire
RS-485 cable directly to the Frick Communications
Converter Module:
-RX/TX
+RX/TX

RS-485 Connections

090.020-CS (JUNE 11)


Page 132

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

APPENDIX B
QUANTUM LX ETHERNET COMMUNICATIONS WIRING

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 133

APPENDIX C
QUANTUM LX LOCAL ETHERNET CONFIGURATIONS
Switch

Computer

Quantum LX

Quantum LX

Typical Small Local Quantum LX Ethernet Configuration

Switch

Switch

Switch

Computer
Quantum LX

Quantum LX

Computer

Quantum LX

Quantum LX

Quantum LX

Quantum LX

Quantum LX

Typical Large Local Quantum LX Ethernet Configuration

090.020-CS (JUNE 11)


Page 134

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

APPENDIX D
QUANTUM LX ETHERNET NETWORK CONFIGURATIONS
Internet

Ethernet Network
Switch

Computer

Quantum LX

Quantum LX

Typical Small Quantum LX Ethernet Network Configuration


Internet

Ethernet Network

Switch

Switch

Switch

Computer
Quantum LX

Computer

Quantum LX

Quantum LX

Quantum LX

Quantum LX

Quantum LX

Quantum LX

Typical Large Quantum LX Ethernet Network

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

APPENDIX E

QUANTUM LX SERIAL COMMUNICATIONS WIRING

090.020-CS (JUNE 11)


Page 135

Modicon PLC with a


MODBUS
communications port

Typical MODBUS (ASCII) Setup

PLC
With serial interface
adapter card that
supports our MODBUS
and/or our AB SLC 500
DF1 protocol (SEE
ABOVE)

DCS (Distributed Control


System) OR

Generic DCS/PLC Setup

RS-232

RS-232

RS-232

RS-422

RS-232

Quantum

Quantum

RS-232 to 422/485
Converter

RS-422 / RS-485

RS-232 to 422/485
Converter

RS-422 / RS-485

RS-422 / RS-485

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

090.020-CS (JUNE 11)


Page 136
QUANTUM LX COMPRESSOR CONTROL PANEL
COMMUNICATIONS SETUP
SERIAL CONNECTIONS PICTORIAL

PLC-5

DCS (Distributed Control


System) with PLC-5
communication driver

RS-232

RS-232

DH+

RS-232

Panel View Operator


Interface

DH+

ASCII RS-232 Serial


Card Installed in the
DCS

AB Special Application Examples

SLC 504

PLC-5

Typical Allen-Bradley (DF1) Setup

SLC 5/04

KF2

Quantum

SLC 5/04

RS-232 to 422/485
Converter

DH+

RS-232 to 422/485
Converter

RS-422 /
RS-485

RS-422 / RS-485

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

Quantum

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP
090.020-CS (JUNE 11)
Page 137

SERIAL CONNECTIONS PICTORIAL (Continued)

090.020-CS (JUNE 11)


Page 138

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

COMMUNICATIONS WIRING DIAGRAMS


TO CUSTOMER REMOTE COMPUTER/DCS
RS-485 COMMUNICATIONS

To Customer
Remote Computer
/ DCS System

-RX/-TX

BLK

+RX/+TX

CLR

- Cable Belden #9841


#24 AWG or Equal

QUANTUM 3 / LX
COM-2 (TB2)

QUANTUM 1 / 2
COM-2 (P12)

BLK

CLR

QUANTUM 4 / LX
COM-2 (TB2)

BLK

BLK

BLK

1 -RX/-TX

CLR

CLR

CLR

2 +RX/+TX

3
4

3
4
5
6
7
8
COMPRESSOR #1

QUANTUM 5 / LX
COM-3 (P16)

3
4

COMPRESSOR #2

3
4

COMPRESSOR #3

COMPRESSOR #4

TO CUSTOMER REMOTE COMPUTER/DCS


RS-485 COMMUNICATIONS

To Customer
Remote Computer /
DCS System

QUANTUM 1 / 2
COM-2 (P12)

-TX

BLK

+TX

GRN

BLK

BLK

BLK

-RX

GRN

GRN

GRN

+RX

3
4

BLK

9
8

BLK

3
4

-TX

-RX

BLK

BLK

+RX

RED

RED

- Cable Belden #9829


#24 AWG or Equal

QUANTUM 5 / LX
COM-3 (P16)

QUANTUM 4 / LX
COM-2 (TB2)

QUANTUM 3 / LX
COM-2 (TB2)

3
4
5
6
7
8
COMPRESSOR #1

COMPRESSOR #2

RED

COMPRESSOR #3

RED

COMPRESSOR #4

+TX

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

090.020-CS (JUNE 11)


Page 139

090.020-CS (JUNE 11)


Page 140

QUANTUM LX COMPRESSOR CONTROL PANEL


COMMUNICATIONS SETUP

Form 090.020-CS (2011-06)


Supersedes: 090-020 CS (MAR 10)
Subject to change without notice
Printed In USA - GUI 1M .20

2011 Johnson Controls Inc. - ALL RIGHTS RESERVED

PRINTED ON LUSTRO OFFSET ENVIRONMENTAL


CONTAINS 30% POST-CONSUMER WASTE

JOHNSON CONTROLS
100 CV Avenue P.O. Box 997
Waynesboro, PA USA 17268-0997
Phone: 717-762-2121 FAX: 717-762-8624
www.johnsoncontrols.com

You might also like