Def Defogger X Trail 2015
Def Defogger X Trail 2015
Def Defogger X Trail 2015
SECTION
DEF
DEFOGGER
CONTENTS
PRECAUTION ............................................... 3
PRECAUTIONS ................................................... 3
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" ................................................................... 3
Handling for Adhesive and Primer ............................ 3
Precaution for Work .................................................. 3
PREPARATION ............................................ 5
SYSTEM .............................................................. 8
Description ...............................................................26
Component Function Check ....................................26
Diagnosis Procedure ...............................................26
Component Inspection .............................................27
PREPARATION ................................................... 5
Description ...............................................................28
Component Function Check ....................................28
DEF-1
DEF
CONDENSER .................................................... 43
DEF-2
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011277714
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
INFOID:0000000011277715
Do not use an adhesive which is past its usable date. Shelf life of this product is limited to six months after
the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the box.
Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
K
Open the seal of the primer and adhesive just before application. Discard the remainder.
Before application, be sure to shake the primer container to stir the contents. If any floating material is found,
do not use it.
If any primer or adhesive contacts the skin, wipe it off with gasoline or equivalent and wash the skin with DEF
soap.
When using primer and adhesive, always observe the precautions in the instruction manual.
M
INFOID:0000000011377301
When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
Protect the removed parts with a shop cloth and prevent them from being dropped.
Replace a deformed or damaged clip.
If a part is specified as a non-reusable part, always replace it with a new one.
Be sure to tighten bolts and nuts securely to the specified torque.
After installation is complete, be sure to check that each part works properly.
Follow the steps below to clean components:
- Water soluble dirt:
Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
Then rub with a soft, dry cloth.
- Oily dirt:
Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
Revision: August 2014
DEF-3
PRECAUTIONS
< PRECAUTION >
Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
DEF-4
PREPARATION
< PREPARATION >
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000011377300
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
(J-46534)
Trim Tool Set
E
AWJIA0483ZZ
DEF
DEF-5
COMPONENT PARTS
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000011277716
ALLIA1538ZZ
A.
No.
1.
B.
Component
Description
3.
Removes the noise that is generated when rear window defogger turns ON/OFF.
4.
Displays the rear window defogger ON to the display when detecting the operation of the
rear window defogger.
5.
BCM
Operates the rear window defogger with the operation of rear window defogger switch.
Performs the timer control of rear window defogger.
6.
Operates the rear window defogger and the door mirror defogger with the control signal
from BCM.
2.
DEF-6
COMPONENT PARTS
< SYSTEM DESCRIPTION >
No.
Description
7.
8.
9.
1:
Component
defogger switch)
2: With
manual A/C
3: With
heated mirrors
INFOID:0000000011277717
Heats the heating wire with the power supply from the rear window
defogger relay to prevent the rear window from fogging up.
JMLIA2595GB
INFOID:0000000011277718
Heats the heating wire with the power supply from the rear window
defogger relay to prevent the door mirror from fogging up.
JMLIA2596GB
DEF
DEF-7
SYSTEM
< SYSTEM DESCRIPTION >
SYSTEM
System Description
INFOID:0000000011277719
SYSTEM DIAGRAM
ALLIA1379GB
OPERATION DESCRIPTION
When rear window defogger switch is turned ON while ignition switch is ON, the rear window defogger
switch transmits rear window defogger switch signal to BCM.
BCM turns rear window defogger relay ON when rear window defogger switch signal is received.
Rear window defogger and door mirror defogger (with door mirror defogger) are supplied with power and
operate when rear window defogger relay turns ON.
Rear window defogger ON is displayed when front air control (manual A/C) or A/C switch (auto A/C)
receives signals.
TIMER FUNCTION
BCM turns rear window defogger relay ON for approximately 15 minutes when rear window defogger switch
is turned ON while ignition switch is ON. It makes rear window defogger and door mirror defogger (with door
mirror defogger) operate.
Timer is canceled after pressing rear window defogger switch again during timer operation. Then BCM turns
rear window defogger relay OFF. The same reaction also occurs during timer operation, if the ignition switch
is turned OFF.
BCM function
Actuator
DEF-8
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000011375876
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
Direct Diagnostic Mode
Description
Ecu Identification
Data Monitor
Active Test
Work support
Configuration
SYSTEM APPLICATION
Work support
REAR DEFOGGER
Warning chime
BUZZER
INT LAMP
Exterior lamp
HEADLAMP
WIPER
FLASHER
INTELLIGENT KEY
Combination switch
COMB SW
BCM
BCM
Immobilizer
IMMU
Door lock
DOOR LOCK
Active Test
Sub System
Configuration
Data Monitor
System
Ecu Identification
BATTERY SAVER
TRUNK
THEFT ALM
RAP system
RETAINED PWR
SIGNAL BUFFER
Air conditioner
AIR CONDITIONER
DEF
DEF-9
REAR DEFOGGER
INFOID:0000000011375875
DATA MONITOR
Monitor Item [Unit]
Description
PUSH SW [On/Off]
ACTIVE TEST
Test Item
REAR DEFOGGER
Description
This test is able to check rear window defogger operation [Off/On].
WORK SUPPORT
Support Item
Setting
Description
MODE3
MODE2
MODE1*
* : Initial setting
DEF-10
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000011375877
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
Direct Diagnostic Mode
Description
Ecu Identification
Data Monitor
Active Test
Work support
Configuration
SYSTEM APPLICATION
Work support
DOOR LOCK
REAR DEFOGGER
Warning chime
BUZZER
INT LAMP
Exterior lamp
HEADLAMP
WIPER
FLASHER
Combination switch
COMB SW
BCM
BCM
Immobilizer
IMMU
BATTERY SAVER
TRUNK
THEFT ALM
RAP system
RETAINED PWR
TPMS
Active Test
Door lock
Configuration
Data Monitor
Sub System
System
Ecu Identification
INFOID:0000000011375878
DATA MONITOR
DEF-11
REAR DEFOGGER
DEF
Description
Indicates condition of rear window defogger switch.
ACTIVE TEST
Test Item
REAR DEFOGGER
Description
This test is able to check rear window defogger operation [Off/On].
WORK SUPPORT
Support Item
Setting
Description
MODE3
MODE2
MODE1*
* : Initial setting
DEF-12
INFOID:0000000011277724
ECU
Reference
DEF
DEF-13
WIRING DIAGRAM
REAR WINDOW DEFOGGER SYSTEM
Wiring Diagram
INFOID:0000000011277725
AALWA1040GB
DEF-14
DEF
O
AALIA2107GB
DEF-15
AALIA2108GB
DEF-16
DEF
O
AALIA2948GB
DEF-17
AALIA2110GB
DEF-18
DEF
O
AALIA2111GB
DEF-19
AALIA2238GB
DEF-20
BASIC INSPECTION
INFOID:0000000011277726
OVERALL SEQUENCE
C
DEF
JMKIA0101GB
DETAILED FLOW
Revision: August 2014
DEF-21
2. CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is displayed.
Record DTC and freeze frame data (Print them out with CONSULT.)
Erase DTC.
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
DEF-22
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 8.
YES (Symptom remains)>>GO TO 6.
NO
>> Inspection End.
DEF
DEF-23
DTC/CIRCUIT DIAGNOSIS
REAR WINDOW DEFOGGER SWITCH
WITH MANUAL A/C
WITH MANUAL A/C : Description
INFOID:0000000011277727
The rear window defogger is operated by pressing the rear window defogger switch ON.
The indicator lamp in the rear window defogger switch illuminates while the rear window defogger is ON.
INFOID:0000000011277728
INFOID:0000000011277729
With CONSULT
Select REAR DEFOGGER of BCM.
Select REAR DEF SW in Data Monitor.
Check REAR DEF SW indication under the following conditions.
Monitor item
REAR DEF SW
Condition
Rear window defogger switch
Status
Pressed
On
Not Pressed
Off
INFOID:0000000011277730
The rear window defogger is operated by pressing the rear window defogger switch ON.
The indicator lamp in the rear window defogger switch illuminates while the rear window defogger is ON.
INFOID:0000000011277731
DEF-24
INFOID:0000000011277732
With CONSULT
1. Select REAR DEFOGGER of BCM.
2. Select REAR DEF SW in Data Monitor.
3. Check REAR DEF SW indication under the following conditions.
Monitor item
REAR DEF SW
Condition
Rear window defogger switch
C
Status
Pressed
On
Not Pressed
Off
DEF
DEF-25
INFOID:0000000011277733
INFOID:0000000011277734
Diagnosis Procedure
INFOID:0000000011277735
()
Connector
Terminal
M18
24
Ground
Voltage (V)
(Approx.)
Condition
ON
OFF
Battery voltage
1.
2.
3.
Connector
Terminal
Connector
Terminal
M18
24
M44
6P
Continuity
Yes
DEF-26
Component Inspection
INFOID:0000000011277736
Terminal
Condition
Rear window
defogger relay
3
Continuity
Yes
No current supply
No
SEF497Y
DEF
DEF-27
INFOID:0000000011277737
Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window
from fogging up.
INFOID:0000000011277738
Diagnosis Procedure
INFOID:0000000011277739
1. CHECK FUSES
Check if any of the following fuses in fuse block (J/B) are blown.
COMPONENT PARTS
Fuse block (J/B)
AMPERE
FUSE NO.
15A
23
15A
24
1.
2.
()
Connector
Terminal
B29
3T, 5T
Ground
Voltage (V)
(Approx.)
Condition
ON
Battery voltage
OFF
1.
2.
DEF-28
(+)
Rear window defogger
Connector
()
Voltage (V)
(Approx.)
Condition
Terminal
D510
Ground
ON
Battery voltage
OFF
Terminal
D525
Continuity
Ground
Yes
Connector
Terminal
B6
Continuity
Yes
DEF
6. CHECK FILAMENT
Check filament.
Refer to DEF-29, "Component Inspection".
Is the inspection result normal?
YES >> Refer to GI-44, "Intermittent Incident".
NO
>> Repair filament. Refer to DEF-41, "Inspection and Repair".
Component Inspection
N
INFOID:0000000011277740
1. CHECK FILAMENT
Check the filament for damage or open circuits.
Refer to DEF-41, "Inspection and Repair".
Is the inspection result normal?
YES >> Inspection End.
NO
>> Repair filament. Refer to DEF-41, "Inspection and Repair".
DEF-29
INFOID:0000000011277741
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
INFOID:0000000011277742
Diagnosis Procedure
INFOID:0000000011277743
()
Connector
Terminal
D14
Voltage (V)
(Approx.)
Condition
Ground
ON
Battery voltage
OFF
1.
2.
Terminal
D14
10
Ground
Continuity
Yes
DEF-30
Component Inspection
C
INFOID:0000000011277744
Continuity
10
Yes
DEF
DEF-31
INFOID:0000000011277745
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
INFOID:0000000011277746
Diagnosis Procedure
INFOID:0000000011277747
()
Connector
Terminal
D107
Voltage (V)
(Approx.)
Condition
Ground
ON
Battery voltage
OFF
1.
2.
Terminal
D107
10
Ground
Continuity
Yes
DEF-32
Component Inspection
INFOID:0000000011277748
Continuity
10
Yes
DEF
DEF-33
SYMPTOM DIAGNOSIS
DEFOGGER SYSTEM SYMPTOMS
Symptom Table
INFOID:0000000011277749
Symptom
Reference page
Rear window defoggers do not operate but both of the door mirror defoggers* operate.
Both door mirror defoggers* dont operate but rear window defoggers operate.
Rear window defogger switch does not light, but rear window defogger operates.
*:if equipped
DEF-34
INFOID:0000000011277750
(+)
Fuse block (J/B)
()
Connector
Terminal
M44
4P, 5P
Ground
Voltage (V)
(Approx.)
Condition
ON
Battery voltage
OFF
DEF
DEF-35
REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR MIRROR DEFOGGER OPERATE.
< SYMPTOM DIAGNOSIS >
INFOID:0000000011277751
DEF-36
BOTH DOORS MIRROR DEFOGGER DONT OPERATE BUT REAR WINDOW DEFOGGER OPERATES
Diagnosis Procedure
INFOID:0000000011277752
AMPERE
FUSE NO.
10A
22
(+)
Fuse block (J/B)
Connector
M44
()
Voltage (V)
(Approx.)
Condition
Terminal
4P, 5P
Ground
ON
Battery voltage
OFF
DEF
DEF-37
INFOID:0000000011277753
DEF-38
INFOID:0000000011277754
DEF
DEF-39
REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WINDOW
DEFOGGER OPERATES
< SYMPTOM DIAGNOSIS >
REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WINDOW DEFOGGER OPERATES
Diagnosis Procedure
INFOID:0000000011277755
DEF-40
FILAMENT
< REMOVAL AND INSTALLATION >
FILAMENT
Inspection and Repair
INFOID:0000000011277756
INSPECTION
1.
When measuring voltage, wrap tin foil around the top of the negative probe. Then press the foil against the wire with your finger.
SEL122R
2.
I
SEL263
3.
4.
DEF
SEL265
REPAIR
REPAIR EQUIPMENT
Conductive silver composition (Dupont No. 4817 or equivalent)
DEF-41
FILAMENT
< REMOVAL AND INSTALLATION >
Ruler 30 cm (11.8 in) long
Drawing pen
Heat gun
Alcohol
Cloth
REPAIRING PROCEDURE
1.
2.
3.
Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol.
Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use.
Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
PIIA0215E
4.
After repair has been completed, check repaired wire for continuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
SEL012D
5.
SEL013D
DEF-42
CONDENSER
< REMOVAL AND INSTALLATION >
CONDENSER
INFOID:0000000011277757
REMOVAL
1.
2.
Remove luggage side upper finisher (LH/RH). Refer to INT-36, "LUGGAGE SIDE UPPER FINISHER :
Removal and Installation".
Remove headlining clips (A) using suitable tool (B) and partially
lower headlining (rear).
ALLIA1604ZZ
3.
4.
ALLIA1370ZZ
INSTALLATION
Installation is in the reverse order of removal.
DEF
DEF-43