Chemistry, Manufacturing and Controls Requirements: Exhibit 1: CMC Requirements For A New Pharmaceutical

Chemistry,
manufacturing and
controls requirements
The chemistry, manufacturing and controls (CMC) section is a very important part of any clinical trial or marketing
application. Drugs can be denied marketing approval if the quality of the product and the manufacturing process
cannot be shown to be of a sufficiently high standard to satisfy regulators.
The following outlines the key parts of the CMC portion of a file, as per the International Conference on
Harmonisation (ICH) requirements.
Exhibit 1: CMC requirements for a new pharmaceutical
Drug substance
Section
Inclusions
General information
Recommended international non-proprietary name (INN),

compendial name (if relevant), chemical name, company
or lab code, other non-proprietary names, chemical
abstracts service (CAS) registry number, structure, general
physicochemical and other relevant properties.
Manufacture
Name, address and responsibility of each manufacturer

involved in process, description of manufacturing process
and controls, control of materials, controls of critical steps
and intermediates, process validation and/or evaluation,
manufacturing process development.
Characterisation
Elucidation of structure and other characteristics,

impurities.
Control of drug substance
Specification, analytical procedures, validation of analytical

procedures, batch analyses, justification of specification.
Reference standards or materials
Drug product
Container closure system
Description, identity and specifications.
Stability
Stability summary and conclusions, post-approval stability

protocol and stability commitment, stability data.
Description and composition
Description, composition, type of container closure system.
Pharmaceutical development
Components of the drug product (drug substance,

excipients), formulation development, overage,
physicochemical and biological properties, manufacturing
process development, container closure system,
microbiological attributes, compatability.
Manufacture
Manufacturers name, batch formula, description of

manufacturing process and process controls, controls of
critical steps and intermediates, process validation and/or
evaluation.
MaRS Copyright 2010
Control of excipients
Specifications, analytical procedures, validation of

analytical procedures, justification of specifications,
excipients of animal or human origin, novel excipients.
Control of drug product
Specifications, analytical procedures, validation of

analytical procedures, batch analyses, characterization of
impurities, justification of specifications.
Reference standards or materials

Container closure system
Stability
Stability summary and conclusion, post-approval stability

protocol and stability commitment, stability data.
Source: International Conference on Harmonisation, Common Technical Document for the Registration of
Pharmaceuticals for Human Use [Guideline M4Q(R1)], http://www.ich.org/LOB/media/MEDIA556.pdf
The ICH guideline Q1A(R2) (Stability Testing of New Drug Substances and Products) defines the stability data
package required for new drug substances and products submitted for approval in each of the major regions that
accept the ICH guidelines (i.e., US, Japan and EU).
Stability testing
The purpose of stability testing is to determine how the drug substance or product performs under different
environmental conditions such as temperature, humidity and light. It also establishes a re-test period for the drug
substance or a shelf-life for the drug product, as well as recommended storage conditions.
Drug substance stability testing

At least three batches of a drug substance should be tested. The ICH guideline Q1A(R2) states that, Batches must
be manufactured at least to pilot scale by the same synthetic route as production batches and using a method of
manufacture and procedure that simulates the final process to be used for production batches. The stability testing
should be conducted on products that have been stored in the same type of container that is intended for market
use (e.g., bottles, blister packages).
For drug substances with a proposed twelve-month re-test period, ideally batches should be tested every three
months over the first year and every six months over the second year, and annually thereafter.
Under accelerated storage conditions, in a six-month study, batches should be tested at the zero-, three- and sixmonth mark.
Drug product stability testing

Stability testing should be conducted from three primary batches of the same formulation and packaged in the
same container closure system as intended for market use. The manufacturing process should simulate the one
used for production batches and should provide a product of the same quality and that meets the same release
specifications as the batches intended for the market. Two of the three batches should be pilot scale batches; the
third one can be smaller, if justified. Where possible, the three batches should be made using different batches of
drug substances.
Note that additional stability and compatibility studies may be required if a product is to be combined with either
another product or diluted in a vehicle for administration.
Exhibits 2, 3 and 4 below detail the general stability data required for drug substances and drug products, as well as
the stability requirements when they are refrigerated or frozen.
MaRS Copyright 2010
Exhibit 2: General stability data required for drug substance or drug product
Study
Storage condition
Minimum time period covered by

data at time of submission
Long-term**
25C+2C/60% RH +5% RH
or
30C+2C/65% RH +5% RH
12 months
Intermediate*
30C+2C/65% RH +5% RH
6 months
Accelerated
40C+2C/75% RH +5% RH
6 months
** It is up to the applicant to decide whether long-term stability studies are performed at which of the two conditions.
* If 30C+2C/65% RH+5% RH is the long-term condition, there is no intermediate condition.
Source: International Conference on Harmonisation, Stability Testing of New Drug Substances and Products
[Guideline Q1A(R2)], http://www.ich.org/LOB/media/MEDIA419.pdf
Exhibit 3: Stability requirements for refrigerated drug substance or drug product

Study
Storage condition

Long-term
5C+3C
12 months
Intermediate
25C+2C/60% RH +5% RH
6 months
Exhibit 4: Stability requirements for frozen drug substance or drug product

Study
Storage condition

Long-term
-20C+5C
12 months
MaRS Copyright 2010

Chemistry, Manufacturing and Controls Requirements: Exhibit 1: CMC Requirements For A New Pharmaceutical

Uploaded by

Copyright:

Available Formats

Chemistry, Manufacturing and Controls Requirements: Exhibit 1: CMC Requirements For A New Pharmaceutical

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chemistry, Manufacturing and Controls Requirements: Exhibit 1: CMC Requirements For A New Pharmaceutical

Uploaded by

Copyright:

Available Formats

What are the key parts of the CMC portion of a file as per ICH requirements?

What are the key parts of the CMC portion of a file as per ICH requirements?

What is the purpose of stability testing?

What is the purpose of stability testing?

Chemistry,

Exhibit 1: CMC requirements for a new pharmaceutical

Recommended international non-proprietary name (INN),

Name, address and responsibility of each manufacturer

Elucidation of structure and other characteristics,

Control of drug substance

Specification, analytical procedures, validation of analytical

Reference standards or materials

Container closure system

Description, identity and specifications.

Stability summary and conclusions, post-approval stability

Description and composition

Description, composition, type of container closure system.

Components of the drug product (drug substance,

Manufacturers name, batch formula, description of

MaRS Copyright 2010

Specifications, analytical procedures, validation of

Control of drug product

Specifications, analytical procedures, validation of

Reference standards or materials

Stability summary and conclusion, post-approval stability

Drug substance stability testing

Drug product stability testing

MaRS Copyright 2010

Minimum time period covered by

Exhibit 3: Stability requirements for refrigerated drug substance or drug product

Minimum time period covered by

Exhibit 4: Stability requirements for frozen drug substance or drug product

Minimum time period covered by

MaRS Copyright 2010

You might also like