Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 135 views

    Preparation and Requirement

    Uploaded by

    Ady Fardy
    The document provides instructions for conducting an offline compressor water wash of a gas turbine. Key steps include: 1. Ensuring various systems are in normal condition and valves are properly positioned before starting the wash. 2. Preparing the water wash skid with a minimum 2/3 full water tank heated to 80°C, along with detergent in the proper proportion. 3. Performing the offline water wash procedure which involves manually starting fans, selecting the offline wash mode, starting the turbine in crank mode, and spraying clean water for 15 minutes followed by a detergent solution for 5-9 minutes while shutting down the turbine.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Preparation and Requirement

    Uploaded by

    Ady Fardy
    135 views2 pages
    The document provides instructions for conducting an offline compressor water wash of a gas turbine. Key steps include: 1. Ensuring various systems are in normal condition and valves are properly positioned before starting the wash. 2. Preparing the water wash skid with a minimum 2/3 full water tank heated to 80°C, along with detergent in the proper proportion. 3. Performing the offline water wash procedure which involves manually starting fans, selecting the offline wash mode, starting the turbine in crank mode, and spraying clean water for 15 minutes followed by a detergent solution for 5-9 minutes while shutting down the turbine.

    Original Description:

    h

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for conducting an offline compressor water wash of a gas turbine. Key steps include: 1. Ensuring various systems are in normal condition and valves are properly positioned before starting the wash. 2. Preparing the water wash skid with a minimum 2/3 full water tank heated to 80°C, along with detergent in the proper proportion. 3. Performing the offline water wash procedure which involves manually starting fans, selecting the offline wash mode, starting the turbine in crank mode, and spraying clean water for 15 minutes followed by a detergent solution for 5-9 minutes while shutting down the turbine.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    135 views2 pages

    Preparation and Requirement

    Uploaded by

    Ady Fardy
    The document provides instructions for conducting an offline compressor water wash of a gas turbine. Key steps include: 1. Ensuring various systems are in normal condition and valves are properly positioned before starting the wash. 2. Preparing the water wash skid with a minimum 2/3 full water tank heated to 80°C, along with detergent in the proper proportion. 3. Performing the offline water wash procedure which involves manually starting fans, selecting the offline wash mode, starting the turbine in crank mode, and spraying clean water for 15 minutes followed by a detergent solution for 5-9 minutes while shutting down the turbine.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 2

    Preparation and Requirement

    Gas Turbine
    1. Cooling water system, lube oil system and auxiliary system are normal condition.
    2. The maximum temperature between turbine wheels is required to be lower than 100C.
    3. After gas turbine is shut down, the difference of the maximum temperature between
    turbine wheels and the washing temperature should be less than 67C, and should be
    recorded.
    Valves Line Up
    1. Physical check of the inlet air to ensure no large deposits on the bellmouth. Remove if
    any.
    2. Close AD-1, AD-2, AD-3 and AD-4 isolation valves.
    3. Close the atomizing air system exhaust isolation valves
    4. Close the shaft sealing and cooling exhaust AE-5 and AE-11 isolation valve.
    5. Close the stage 13 exhaust isolation AE-13.
    6. Open the air vent valve, CA1.
    7. Open the compressor inlet pipe 20TW motor valve.
    8. Open the drain valve at the bottom of the compressor.
    9. Open the 6 units of drain valves under the turbine.
    10. Open the drain valve of AD-3 to APU.
    11. Open the water wash discharging valve at the bottom of exhaust compartment.
    GT Compressor Wash Skid
    1. Power supply of the water wash skid is energized.
    2. Water tank of the water-wash module is min 2/3 and the liquid level of the detergent is
    full with 6 pails of chemical detergent 20 Litre each.
    3. Pre-heating of the Water tank in the GT Water Wash Skid to approximately 80C.
    4. Feed detergent prepared proportionally in the detergent tank. The proportion of water and
    detergent should be 1:4.
    5. Open the main outlet valve at Water Wash Skid.
    6. Demin water pump, 88TW, capacity is 50 m3/h and for the requirement water flow for
    Offline water wash is only 9.5 m3/h. so, throttle the Demin pump outlet valve 20% to
    achieve the required flow.
    7. Open the Water Wash Primary, Secondary, and dosing valves.
    8. Start the washing pump to totally discharge cold water in the pipeline between the waterwash module and the gas turbine.
    Offline Compressor Water Wash Procedure

    1. Manually start 88TK-1 and 88TK-2 fans. They should be started at an of interval at least
    10s.
    2. Selection of off-line water wash mode: enter WW-offline menu in AUX interface on the
    control computer, select ON under OFF LINE WATER WASH.
    3. Select the mode of Crank in the main menu (it is forbidden to select Fire or Auto), and
    start the gas turbine as the normal start steps.
    4. Make sure that Inlet Guide Vane, IGV, is at totally opened position of 86.
    5. Make sure water temperature is within the regulated scope and the water inlet valve of
    the gas compressor is opened.
    6. Start the clean water pump to continuously spray to the gas compressor for 15 minutes,
    and check the water outlet condition of each drain valve.
    7. Start the detergent pump, 88DM, and the outlet valve throttle 100% to observe the water
    drainage condition of each drain valve to ensure detergent enter the units.
    8. Continue the detergent-water spraying for 5-9 minutes.
    9. Shut down the gas turbine, always spray water to the unit during shutdown till

    You might also like