Reverse Circulation

Junk Baskets
Manual C315

CONTENTS

Logan Reverse Circulation Junk Baskets

Overview................................................................................ 2
Uses ...................................................................................... 2
Construction .......................................................................... 2
Operation............................................................................... 2
Tool Illustration....................................................................... 3
Recovering a Fish with a Junk Basket
Equipped with a Mill Shoe.................................................. 4
Recovering a Fish with a Junk Basket
Equipped with a Finger Shoe............................................. 4
Maintenance .......................................................................... 4
Disassembly .......................................................................... 5
Assembly ............................................................................... 5
Specifications and Parts Lists.......................................... 6 8
Junk Catcher Assemblies .............................................. 9 18
Rock Bit Cone Dimensions.................................................. 19

LEGAL NOTICE
All references to Bowen part numbers in this literature are
used to identify interchangeable tools and parts. Reference to
such tools and parts does not imply that Logan Oil Tools is a
licensee or is in any way affiliated with National Oilwell Varco.
Logan Oil Tools does not sell, or offer to sell, National Oilwell
Varco (Bowen) products.
Bowen is a registered trademark of National Oilwell Varco.

3rd Printing. Rev. 2 February 2013

Logan Reverse Circulation Junk Baskets 1

Manual C315 Logan Reverse Circulation Junk Baskets Page 1

OVERVIEW
The Logan Reverse Circulation Junk
Basket is designed to successfully
remove all types of small junk objects
from the hole by utilizing the principle
of reverse fluid circulation. Reverse fluid
circulation ensures a more complete
recovery of junk in the hole and eliminates misruns. Reverse fluid circulation
can be maintained even when the tool
is fitted with a fishing magnet.
The tools drain feature eliminates pulling a wet string even if the inner barrel
becomes plugged.
USES
The Logan Reverse Circulation Junk
Basket is used to retrieve all types of
junk that accumulate at the bottom of a
well: rock bit cones and bearings, tong
pins, broken slips, bits of wireline, small
hand tools, debris from twisted-off drill
strings, mill cuttings, and similar items.
CONSTRUCTION
The Logan Reverse Circulation Junk
Basket consists of a lifting sub (provided for ease of handling and for storage
of the steel drop ball), top sub, valve
assembly, barrel, Type A mill shoe, and
a single junk catcher. Assemblies with
two junk catchers are available upon
request. For the component breakdown
of the junk catcher assemblies, refer to
the Junk Catcher Assemblies tables on
pages 10 18.
Reverse circulation is obtained by the
unique construction of the barrel, which
is basically a two-bowl assembly.
When the steel ball is in place in the
valve seat, circulation fluid is directed
around the valve through the inner passages of the barrel, jetted outward and
downward against the full circumference of the hole, flows in a continuous
stream into the barrel, up through the
barrel, then out the return ports at the
upper end of the barrel.

Optional Accessories
The hard, rugged, and long-lasting
qualities of tungsten carbide faced
shoes will cut away any protruding
excess metal that may interfere with
the free entry and retention of the
debris into the junk basket.

Magnet Inserts
Logan Reverse Circulation Junk
Baskets can be easily converted to
an effective fishing magnet with the
advantages of reverse fluid circulation
by replacing the Junk Catcher Assembly
with a Logan Magnet Insert.

If the fish is embedded in a hard formation and a core must be cut, the Junk
Basket must be equipped with the
proper mill shoe. If the fish is laying
loosely on the bottom of the hole, the
Junk Basket may be equipped with
either a proper mill or finger shoe.

Logan Magnet Inserts are machined to

fit into the recess normally occupied by
the Junk Catcher Assembly. The Logan
Magnet Insert is generally used to thoroughly clean the hole prior to diamond
drilling and in hard-to-drill formations.

Mill Shoes
Logan Reverse Circulation Junk
Baskets are furnished with a standard
Type A mill shoe. It is constructed of
conventional hard metal and has side
wings.

The Logan Reverse Circulation Junk

Basket is made up to the bottom of the
fishing string and lowered to a point
within several feet from the bottom of
the hole. Begin circulation to wash the
hole. Stop circulation and drop the steel
ball.

The Type B mill shoe is similar to the

Type A design, but is dressed with sintered tungsten carbide. This extremely
tough, hard-faced material will rapidly
and effectively mill junk during fishing
operations.
The Type C Mill Shoe is a flat-bottomed
shoe. It is dressed with sintered tungsten carbide on the bottom and on the
inner and outer faces. It will effectively
mill junk and is especially effective for
cutting cores.
Finger Shoes
A finger shoe may be installed on the
bottom of the barrel in place of the mill
shoe when junk is too large to pass
through the catchers. Finger shoes will
normally retrieve larger objects than mill
shoes, provided the junk is lying loose
on the bottom of the well and a core
does need not to be taken.
After the Junk Basket has engaged the
fish, combined rotating and lowering will
cause the long fingers to close under
the fish and retain it in the barrel. Finger
replacements are easy and inexpensive
to replace on the finger shoe body.

2 Logan Reverse Circulation Junk Baskets

Page 2 Logan Reverse Circulation Junk Baskets Manual C315

OPERATION

When the steel ball is dropped into the

valve seat, circulation fluid travels outward and downward through the inner
passage of the barrel and out through
the vents in the lower end. The fluid is
then deflected to the center of the tool
and up through the return holes in the
upper end of the barrel. This reverse
fluid circulation directs and carries the
debris into the hollow barrel above the
junk catcher assembly.

CAUTION: Make sure the inside

diameters of the tool joints in the
string are large enough to pass the
steel ball. Be sure to retain the steel
ball at the surface while the Junk
Basket is being lowered into the
hole.
Circulation is resumed and the tool is
lowered with slow right-hand rotation
until a 10-inch core has been cut. Stop
rotation and circulation and pull the tool
from the hole.

Top Sub

Valve Cup

Valve Seat
and Steel Ball

Barrel

Junk Catcher
Assembly

Mill Shoe

Logan Reverse Circulation Junk Basket

Logan Oil Tools reserves the right to change or discontinue designs without notice.

Logan Reverse Circulation Junk Baskets 3

Manual C315 Logan Reverse Circulation Junk Baskets Page 3

Recovering a Fish with a Junk

Basket Equipped with a Mill Shoe
First, determine that the Junk Basket is
properly assembled and that all of the
parts are in good working condition.
When the Junk Basket is approximately
ten feet off the bottom of the hole, turn
on the circulating pumps to force circulation through the Junk Basket for a few
minutes before dropping the steel ball.
Maintain circulation for a few minutes
to condition the mud and flush out any
mud that may have accumulated in the
barrel during the run in. Turn off the
circulating pumps.
Unscrew the kelly from the string. Drop
the steel ball down the drill pipe and
reconnect the kelly. If a window sub
is available, remove the plug from the
window sub and drop the steel ball
down the drill pipe. Replace the plug
in the window sub.
After the steel ball has dropped down
the drill pipe, its downward progress will
be halted when it encounters the valve
seat in the Junk Basket. When circulation is resumed, the fluid is forced in
a continuous stream that creates the
reverse circulation action to the center of the Junk Basket, up through the
inner passages of the barrel, jetted out
of the return ports in the upper barrel
and down against the full circumference
of the hole, and deflected to flush all
objects and debris towards the center.
Turn on the circulating pumps. While
maintaining high pressure circulation,
rotate the string slowly to the right and
lower the Junk Basket to the bottom of
the hole. Continue right-hand rotation
and lower until a 10-inch-long core has
been cut.

NOTE: When using hard-faced mill

shoes, maintain one ton of weight
on the shoe and rotate the basket 50
150 rpm to ensure proper milling.

The piece of cut core allows the fish to

ride past the junk catcher. The fingers
on the junk catcher fold back while the
core and fish enter. Pulling up the Junk
Basket will cause the junk catcher's fingers to dig in and cut off a section of the
core, thereby holding the fish and core
securely in the Junk Basket barrel.
Stop rotation and circulation and pull
the Logan Reverse Circulation Junk
Basket from the hole.
Recovering a Fish with a Junk
Basket Equipped with a Finger Shoe
First, determine that the Junk Basket is
properly assembled and that all of the
parts are in good working condition.
Remove the lifting sub and keep it and
the steel ball at the derrick floor.
Using the top sub, connect the Junk
Basket to the string and run it in the
hole. If small junk particles are prevalent in the hole, a Junk Sub should
be installed on top of the top sub. If a
window sub is available, install the junk
sub on the top joint of drill pipe before
connecting the kelly.
When the Junk Basket is approximately
ten feet off the bottom of the hole, turn
on the circulating pumps to force circulation through the Junk Basket for a few
minutes before dropping the steel ball.
Maintain circulation for a few minutes
to condition the mud and flush out any
mud that may have accumulated in the
barrel during the run in. Turn off the
circulating pumps.
Unscrew the kelly from the string. Drop
the steel ball down the drill pipe and
reconnect the kelly. If a window sub
is available, remove the plug from the
window sub and drop the steel ball
down the drill pipe. Replace the plug in
the window sub.

4 Logan Reverse Circulation Junk Baskets

Page 4 Logan Reverse Circulation Junk Baskets Manual C315

After the steel ball has dropped down

the drill pipe, its downward progress will
be halted when it encounters the valve
seat in the Junk Basket. When circulation is resumed, the fluid is forced in
a continuous stream that creates the
reverse circulation action to the center of the Junk Basket, up through the
inner passages of the barrel, jetted out
of the return ports in the upper barrel
and down against the full circumference
of the hole, and deflected to flush all
objects and debris towards the center.
Turn on the circulating pumps. While
maintaining high pressure circulation,
rotate the string slowly to the right and
lower it until approximately two tons of
weight rest against the bottom of the
hole. This will cause the fingers of the
finger shoe to close under the fish. Stop
rotation and circulation and pull the
Junk Basket from the hole.
Fish or Core Removal
Unscrew the mill or finger shoe from the
Junk Basket and thoroughly wash out
the barrel.

NOTE: The Logan Reverse Circulation Junk Basket should be washed

as soon as possible after use. Pay
particular attention to the space between the inner and outer barrels.
MAINTENANCE
Good maintenance will ensure the best
performance and maximum life of the
Logan Reverse Circulation Junk Basket.
Disassemble and thoroughly clean the
Logan Reverse Circulation Junk Basket
after each job. Worn or damaged parts
should be replaced during disassembly/
assembly procedures.

NOTE: If using a Logan Magnet

Insert, thoroughly clean it after each
use and make sure the circulation
hole is clean. Always store the magnet insert with the keeper in place
to preserve magnetism.

DISASSEMBLY

ASSEMBLY

All disassembly and repairs should be

conducted in a clean, well-equipped
shop.

The Logan Reverse Circulation Junk

Basket is easily assembled using standard shop tools. No special tools are
required.

The following disassembly instructions

are for a Logan Reverse Circulation
Junk Basket with a mill or finger shoe:
1. Unscrew the top sub.
2. Unscrew the valve assembly with
the wrench provided.
3. Remove the steel ball and valve
seat.
If the tool is equipped with a finger
shoe, skip to step 5.
4. Unscrew the mill shoe. Remove
the junk catcher from the shoe.
5. Remove the finger shoe:
(a) Unscrew the finger shoe from
the barrel.
(b) Unscrew the finger shoe
replacement from the finger
shoe body.
6. Wash out both the inside and the
inner passages in the barrel.
7. Carefully inspect all parts. Replace
damaged parts with new ones.

Make sure all parts have been thoroughly cleaned, inspected, and lubricated prior to assembly. Replace any
collapsed springs or those that have
a weak recoil. Replace any blades that
are chipped or severely worn. Have
high quality thread compound and a
good grade of lightweight grease on
hand.
1. Carefully inspect all parts. Replace
worn or damaged parts with new
parts.
2. Be sure the inside and inner passages of the barrel are clean.

6. Install the valve assembly with the

wrench provided.
7. Install the top sub.
8. Store the steel ball in the lifting
sub.
9. Paint or coat with grease to
prevent rust.
The Logan Reverse Circulation Junk
Basket is now ready for use.
Magnet Insert Installation
1. Remove the shoe from the barrel
of the Junk Basket.
2. Remove the junk catcher from the
shoe.
3. Install the Magnet Insert into the
junk catcher recess.
4. Reassemble the Junk Basket.

If installing a mill shoe, skip to step 4.

3. Install the finger shoe:
(a) Screw the finger shoe onto
the barrel.
(b) Screw the finger shoe replacement onto the finger shoe body.
4. Install the mill shoe. Install the junk
catcher in the shoe.
5. Install the steel ball and valve seat.

Logan Reverse Circulation Junk Baskets 5

Manual C315 Logan Reverse Circulation Junk Baskets Page 5

LOGAN REVERSE CIRCULATION JUNK BASKET

HOLE SIZE

3-3/4 to 4

BARREL O.D.
MAXIMUM DIAMETER OF FISH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.
TOP SUB

Logan Part No.

Bowen No.
BARREL
Logan Part No.
Bowen No.
VALVE CUP
Logan Part No.
Bowen No.
STEEL BALL
Logan Part No.
Bowen No.
VALVE SEAT
Logan Part No.
Bowen No.
LIFTING SUB
Logan Part No.
Bowen No.
JUNK CATCHER
Logan Part No.
ASSEMBLY (See Note 1) Bowen No.
TYPE A MILL SHOE
Logan Part No.
(Hard Faced Mill Teeth)
Bowen No.

3-5/8
2-11/32
302-363
6635

4-1/8
to 4-1/2
4
2-17/32
302-400
7295

D1000
6636
D2000
6637
D3000
6638
D4000
6640
D5000
6639
D6000
4568
600-015
21795W
D8000-A
6642A

4-5/8 to 5
4-1/2
3-1/16
302-450
4448

5-1/8
to 5-1/2
4-7/8
3-9/16
302-487
4572

D1001
7296
D2001
7297
D3000
6638
D4000
6640
D5000
6639
D6000
4568
600-016
21855W
D8001-A
7299A

D1002
4449
D2002
4450
D3002
4451
D4002
4453
D5002
4452
D6002
424
600-017
21780W
D8002-A
4455A

D8000-B
6642B

D8001-B
7299B

D8000-C
6642C
600-100
6643
3-1/4
D7000
6643-2
D10000
6643-1
600-045
61836
600-068
61810
E4028
61837

D8001-C
7299C
600-101
7300
3-3/4
D7001
7300-2
D10001
7300-1
600-046
61848
600-069
61812
E4029
61849

5-11/16 to 6
5-1/8
3-3/4
302-513
2618

6-1/8
to 6-1/2
5-3/4
4-13/32
302-575
2670

6-5/8
to 7-3/8
6-1/4
4-3/4
302-625
2677

D1003
4573
D2003
4574
D3002
4451
D4002
4453
D5002
4452
D6002
424
600-018
21790W
D8003-A
4576A

D1004
2619
D2004
2620
D3004
2621
D4004
2623
D5004
2622
D6004
425
600-019
21735W
D8004-A
2625A

D1005
2671
D2005
2672
D3004
2621
D4004
2623
D5004
2622
D6004
425
600-020
28349W
D8005-A
2676A

D1006
2678
D2006
2679
D3004
2621
D4004
2623
D5004
2622
D6006
1849
600-021
21750W
D8006-A
2683A

D8002-B
4455B

D8003-B
4576B

D8004-B
2625B

D8005-B
2676B

D8006-B
2683B

D8002-C
4455C
600-102
4456
4-1/16
D7002
4456-2
D10002
4456-1
600-047
61840
600-069
61812
E4016
61841

D8003-C
4576C
600-103
4577
4-1/2
D7003
4577-2
D10003
4577-1
600-048
61850
600-070
61814
E4030
61851

D8004-C
2625C
600-104
22208
4-3/4
D7004
22208-2
D10004
22208-1
600-049
61852
600-070
61814
E4003
61853

D8005-C
2676C
600-105
22218
5-17/32
D7005
22218-2
D10005
22218-1
600-050
61866
600-071
61816
E4018
61867

D8006-C
2683C
600-106
2739
5-29/32
D7006
2739-2
D10006
2739-1
600-051
61872
600-072
61818
E4019
61873

OPTIONAL COMPONENTS
TYPE B MILL SHOE
(Tungsten Carbide
Mill Teeth)
TYPE C MILL SHOE
(Tungsten Carbide Faced)
FINGER SHOES
(Complete Assembly)

Logan Part No.

Bowen No.

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Max. Dia. of Fish
BODY
Logan Part No.
Bowen No.
REPLACEMENT
Logan Part No.
Bowen No.
MAGNET INSERTS
Logan Part No.
(Complete Assembly)
Bowen No.
MAGNETIC ASSEMBLY Logan Part No.
Bowen No.
ADAPTER
Logan Part No.
Bowen No.

Logan Oil Tools reserves the right to change or discontinue designs without notice.
Special Notes:
(1) For the component breakdown of the junk catcher assemblies, refer to the Junk Catcher Assemblies tables on pages 1018.
(2) For type A, B, or C shoes: unless specified, shoes will be furnished with the same O.D. as minimum hole size shown.
(3) Finger shoe replacements are furnished with the same O.D. as the standard shoe unless otherwise specified.
When ordering, please specify:
(1) Complete assembly or part number
(2) Top Sub connection
(3) O.D. and type of shoe

Recommended Spare Parts:

(1) 2 Upper Catchers
(2) 2 Lower Catchers
(3) 2 Mill Shoes
(4) 2 Finger Shoes
(5) 4 Finger Shoe Replacements

6 Logan Reverse Circulation Junk Baskets

Page 6 Logan Reverse Circulation Junk Baskets Manual C315

LEGAL NOTICE
All references to Bowen part numbers in this literature are
used to identify interchangeable tools and parts. Reference to
such tools and parts does not imply that Logan Oil Tools is a
licensee or is in any way affiliated with National Oilwell Varco.
Logan Oil Tools does not sell, or offer to sell, National Oilwell
Varco (Bowen) products.
Bowen is a registered trademark of National Oilwell Varco.

LOGAN REVERSE CIRCULATION JUNK BASKET

HOLE SIZE
BARREL O.D.
MAXIMUM DIAMETER OF FISH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.
TOP SUB

Logan Part No.

Bowen No.
BARREL
Logan Part No.
Bowen No.
VALVE CUP
Logan Part No.
Bowen No.
STEEL BALL
Logan Part No.
Bowen No.
VALVE SEAT
Logan Part No.
Bowen No.
LIFTING SUB
Logan Part No.
Bowen No.
JUNK CATCHER
Logan Part No.
ASSEMBLY (See Note 1) Bowen No.
TYPE A MILL SHOE
Logan Part No.
(Hard faced Mill Teeth)
Bowen No.

7-1/2
to 8-1/4
7
5-3/16
302-700
2554

8-3/8
to 9-1/2
7-7/8
6-1/16
302-787
2567

9-5/8
to 10-5/8
9-1/8
7-1/16
302-913
2659

10-3/4
to 11-5/8
10-1/8
7-11/16
302-1013
2684

11-3/4
to 12-1/2
11
8-5/16
302-1100
2690

12-5/8
to 13-5/8
11-7/8
8-11/16
302-1187
2696

13-3/4
to 16
13
9-7/8
302-1300
2702

D1007
2493
D2007
2555
D3007
2570
D4007
2572
D5007
2571
D6006
1849
600-022
21725W
D8007-A
2556A

D1008
2568
D2008
2569
D3007
2570
D4007
2572
D5007
2571
D6008
426
600-023
18725W
D8008-A
2574A

D1009
2660
D2009
2661
D3009
2662
D4009
2665
D5009
2663
D6009
427
600-024
14633W
D8009-A
2668A

D1010
2685
D2010
2686
D3009
2662
D4009
2665
D5009
2663
D6009
427
500-019
18945W
D8010-A
2689A

D1011
2691
D2011
2692
D3009
2662
D4009
2665
D5009
2663
D6009
427
600-026
21760W
D8011-A
2695A

D1012
2697
D2012
2698
D3009
2662
D4009
2665
D5009
2663
D6009
427
600-027
21840W
D8012-A
2701A

D1013
2703
D2013
2704
D3009
2662
D4009
2665
D5009
2663
D6009
427
600-028
21770W
D8013-A
2707A

D8007-B
2556B

D8008-B
2574B

D8009-B
2668B

D8010-B
2689B

D8011-B
2695B

D8012-B
2701B

D8013-B
2707B

D8007-C
2556C
600-107
2740
6-3/4
D7007
2740-2
D10007
2740-1
600-052
61947
600-073
61820
E4020
61948

D8008-C
2574C
600-108
2741
7-23/32
D7008
2741-2
D10008
2741-1
600-053
61953
600-074
61822
E4021
61954

D8009-C
2668C
600-109
2742
9
D7009
2742-2
D10009
2742-1
600-054
61965
600-075
61826
E4022
61966

D8010-C
2689C
600-110
2743
9-15/16
D7010
2743-2
D10010
2743-1
600-055
61963
600-075
61826
E4023
61968

D8011-C
2695C
600-111
2744
11
D7011
2744-2
D10011
2744-1
600-056
61973
600-076
61828
E4024
61974

D8012-C
2701C
600-112
2745
11-7/8
D7012
2745-2
D10012
2745-1
600-057
61975
600-076
61828
E4025
61976

D8013-C
2707C
600-113
2746
13
D7013
2746-2
D10013
2746-1
600-058
61983
600-077
61830
E4026
61982

OPTIONAL COMPONENTS
TYPE B MILL SHOE
(Tungsten Carbide
Mill Teeth)
TYPE C MILL SHOE
(Tungsten Carbide Faced)
FINGER SHOES
(Complete Assembly)

Logan Part No.

Bowen No.

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Max. Dia. of Fish
BODY
Logan Part No.
Bowen No.
REPLACEMENT
Logan Part No.
Bowen No.
MAGNET INSERTS
Logan Part No.
(Complete Assembly)
Bowen No.
MAGNETIC ASSEMBLY Logan Part No.
Bowen No.
ADAPTER
Logan Part No.
Bowen No.

Logan Oil Tools reserves the right to change or discontinue designs without notice.
Special Notes:
(1) For the component breakdown of the junk catcher assemblies, refer to the Junk Catcher Assemblies tables on pages 1018.
(2) For type A, B, or C shoes: unless specified, shoes will be furnished with the same O.D. as minimum hole size shown.
(3) Finger shoe replacements are furnished with the same O.D. as the standard shoe unless otherwise specified.
When ordering, please specify:
(1) Complete assembly or part number
(2) Top Sub connection
(3) O.D. and type of shoe

Recommended Spare Parts:

(1) 2 Upper Catchers
(2) 2 Lower Catchers
(3) 2 Mill Shoes
(4) 2 Finger Shoes
(5) 4 Finger Shoe Replacements

LEGAL NOTICE
All references to Bowen part numbers in this literature are
used to identify interchangeable tools and parts. Reference to
such tools and parts does not imply that Logan Oil Tools is a
licensee or is in any way affiliated with National Oilwell Varco.
Logan Oil Tools does not sell, or offer to sell, National Oilwell
Varco (Bowen) products.
Bowen is a registered trademark of National Oilwell Varco.

Logan Reverse Circulation Junk Baskets 7

Manual C315 Logan Reverse Circulation Junk Baskets Page 7

LOGAN REVERSE CIRCULATION JUNK BASKET

HOLE SIZE
BARREL O.D.
MAXIMUM DIAMETER OF FISH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.
TOP SUB

Logan Part No.

Bowen No.
BARREL
Logan Part No.
Bowen No.
VALVE CUP
Logan Part No.
Bowen No.
STEEL BALL
Logan Part No.
Bowen No.
VALVE SEAT
Logan Part No.
Bowen No.
LIFTING SUB
Logan Part No.
Bowen No.
JUNK CATCHER
Logan Part No.
ASSEMBLY (See Note 1) Bowen No.
TYPE A MILL SHOE
Logan Part No.
(Hard faced Mill Teeth)
Bowen No.

16
to 17-1/2
15
11-1/8
302-1500
2708
D1014
2709
D2014
2710
D3009
2662
D4009
2665
D5009
2663
D6009
427
600-029
21775W
D8014-A
2713A

OPTIONAL COMPONENTS
TYPE B MILL SHOE
(Tungsten Carbide
Mill Teeth)
TYPE C MILL SHOE
(Tungsten Carbide Faced)
FINGER SHOES
(Complete Assembly)

Logan Part No.

Bowen No.

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Max. Dia. of Fish
BODY
Logan Part No.
Bowen No.
REPLACEMENT
Logan Part No.
Bowen No.
MAGNET INSERTS
Logan Part No.
(Complete Assembly)
Bowen No.
MAGNETIC ASSEMBLY Logan Part No.
Bowen No.
ADAPTER
Logan Part No.
Bowen No.

D8014-B
2713B
D8014-C
2713C
600-114
2747
15-1/4
D7014
2747-2
D10014
2747-1
600-059
61985
600-078
61832
E4027
61986

Logan Oil Tools reserves the right to change or discontinue designs without notice.
Special Notes:
(1) For the component breakdown of the junk catcher assemblies, refer to the Junk Catcher Assemblies tables on pages 1018.
(2) For type A, B, or C shoes: unless specified, shoes will be furnished with the same O.D. as minimum hole size shown.
(3) Finger shoe replacements are furnished with the same O.D. as the standard shoe unless otherwise specified.
When ordering, please specify:
(1) Complete assembly or part number
(2) Top Sub connection
(3) O.D. and type of shoe

Recommended Spare Parts:

(1) 2 Upper Catchers
(2) 2 Lower Catchers
(3) 2 Mill Shoes
(4) 2 Finger Shoes
(5) 4 Finger Shoe Replacements

LEGAL NOTICE
All references to Bowen part numbers in this literature are
used to identify interchangeable tools and parts. Reference to
such tools and parts does not imply that Logan Oil Tools is a
licensee or is in any way affiliated with National Oilwell Varco.
Logan Oil Tools does not sell, or offer to sell, National Oilwell
Varco (Bowen) products.
Bowen is a registered trademark of National Oilwell Varco.

8 Logan Reverse Circulation Junk Baskets

Page 8 Logan Reverse Circulation Junk Baskets Manual C315

Overview
The alternately long and short fingers of the
junk catcher assembly extend almost to the
center of the basket to form a close-fitting
receptacle that will retain small pieces of junk
that may impede drilling progress or hold a core
sample.

LOGAN JUNK CATCHER ASSEMBLIES

Long Finger with Spring

Short Finger with Spring

Construction
The steel body design provides greater strength
and durability. The retainer ring, retainer screws
and springs are made of stainless steel to eliminate rust and corrosion problems. Fingers are
inexpensive and can be easily replaced.
Assembly
After redressing a junk catcher assembly, care
must be taken to ensure that alternate long
and short fingers are assembled in proper
sequence.

Catcher Body

When ordering, please specify:

(1) Name and number of assembly or part
(2) Finger number and code, when ordering
fingers
Recommended Spare Parts:
(1) 2 Sets of Fingers
(2) 4 Sets of Torsion Springs
(3) 1 Set of Pivot Pins
(4) 4 Retainer Screws

Retainer Ring Screw

Stainless Steel
Retainer Ring

LEGAL NOTICE
All references to Bowen part numbers in this
literature are used to identify interchangeable tools
and parts. Reference to such tools and parts does
not imply that Logan Oil Tools is a licensee or is in
any way affiliated with National Oilwell Varco. Logan Oil Tools does not sell, or offer to sell, National
Oilwell Varco (Bowen) products.
Bowen is a registered trademark of National
Oilwell Varco.

Special Notes:
(1) Code: Each finger is stenciled with a letter or letter-number code. These codes are used
in lieu of the part number because of space limitation. See the Finger Code Chart below
to cross-reference the code with the part number.
Finger Code Chart
Code
A
B
C
D
E
F
G
H

Part No.
E11006
E9005
E11005

E9001
E11000
E9013
E9004

Code
I
J
K
L
M
N
O
P

Part No.
E11003
E11014
E9014
E10003
E9010
E11010

Code
P-1
P-2
W-1
W-2
W-3
W-4
X-1
X-2

Part No.
E9007
E11008
E9012
E11013
E9002
E11001
E9019
E11020

Code
21778-W
21779-W
362-W
363-W
690-W
691-W
666-W
667-W

Part No.
E9015
E11016
E9006
E11007
E90015
E11015
E9009
E11011

Logan Reverse Circulation Junk Baskets 9

Manual C315 Logan Reverse Circulation Junk Baskets Page 9

LOGAN JUNK CATCHER ASSEMBLIES

INSIDE DIAMETER
OUTSIDE DIAMETER
LENGTH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.

2-11/32
3-3/32
1-7/8
600-015
21795W

2-39/64
3-15/64
1-7/8
600-031
21810W

2-23/32
3-1/4
1-7/8
500-023
14593-W

2-17/32
3-11/32
1-7/8
14000-008
22070-W

2-17/32
3-11/32
1-7/8
600-016
21855W

2-31/32
3-11/16
2-1/4
500-024
14589-W

3-1/16
3-13/16
2-1/2
14000-009
22075-W

BODY

D11000
56357
D12000
56358
E9011
68368

E11012
68369

4
E12001
45583
8
E13009
45571
8
E14000
42257
2
600-015RK
21795K

D11021
45542
D12019
45538
E9001
45539
E
5

E11000
45540
F
5
E12000
45535
10
E13006
45567
10
E14000
42257
2
600-031RK
21810K

E7000
45541
E8000
45543
E9001
45539
E
5

E11000
45540
F
5
E12000
45535
10
E13006
45567
10
E14000
42257
2
500-023RK
14593K

D11001
68366
D12001
68367
E9011
68368
AD
8

E12001
45583
8
E13009
45571
8
E14000
42257
2
14000-008RK
22070K

D11001
68366
D12001
68367
E9011
68368

E11012
68369

4
E12001
45583
8
E13009
45571
8
E14000
42257
2
600-016RK
21855K

E7001
45590
E8001
45562
E9002
45574
W-3
5

E11001
45575
W-4
5
E12001
45583
10
E13007
55958
10
E14000
42257
2
500-024RK
14589K

D11002
45591
D12002
45592
E9002
45574
R
10

E12001
45583
10
E13009
45571
10
E14000
42257
2
14000-009RK
22075K

FINGER RETAINER
(stainless steel)

SHORT FINGER *

MEDIUM FINGER *

LONG FINGER *

PIVOT PIN *

TORSION SPRING *
(stainless steel)

RETAINER SCREW *
(stainless steel)

REPAIR KITS
* Indicates parts included in kit

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.

Logan Oil Tools reserves the right to change or discontinue designs without notice.
When ordering, please specify:
(1) Name and number of assembly or part
(2) Finger number and code, when ordering fingers
Recommended Spare Parts:
(1) 2 Sets of Fingers
(2) 4 Sets of Torsion Springs
(3) 1 Set of Pivot Pins
(4) 4 Retainer Screws

LEGAL NOTICE
All references to Bowen part numbers in this
literature are used to identify interchangeable tools
and parts. Reference to such tools and parts does
not imply that Logan Oil Tools is a licensee or is in
any way affiliated with National Oilwell Varco. Logan Oil Tools does not sell, or offer to sell, National
Oilwell Varco (Bowen) products.

Special Notes:
(1) Code: Each finger is stenciled with a letter or letter-number code. These codes are used
in lieu of the part number because of space limitation. See the Finger Code Chart below
to cross-reference the code with the part number.
Finger Code Chart
Code
A
B
C
D
E
F
G
H

Part No.
E11006
E9005
E11005

E9001
E11000
E9013
E9004

Bowen is a registered trademark of National

Oilwell Varco.

10 Logan Reverse Circulation Junk Baskets

Page 10 Logan Reverse Circulation Junk Baskets Manual C315

Code
I
J
K
L
M
N
O
P

Part No.
E11003
E11014
E9014
E10003
E9010
E11010

Code
P-1
P-2
W-1
W-2
W-3
W-4
X-1
X-2

Part No.
E9007
E11008
E9012
E11013
E9002
E11001
E9019
E11020

Code
21778-W
21779-W
362-W
363-W
690-W
691-W
666-W
667-W

Part No.
E9015
E11016
E9006
E11007
E90015
E11015
E9009
E11011

LOGAN JUNK CATCHER ASSEMBLIES

INSIDE DIAMETER
OUTSIDE DIAMETER
LENGTH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.

3-1/16
3-13/16
2-1/2
600-017
21780W

3-13/32
3-31/32
1-63/64
600-032
21880W

3-13/32
3-31/32
1-63/64
600-033
21805W

3-9/32
4
2-3/8
500-050
14598-W

3-13/32
4-1/16
2-3/8
500-025
19377-W

3-21/32
4-9/32
2-1/4
600-018
21790W

3-3/4
4-15/32
2-9/16
600-019
21735W

BODY

D11002
45591
D12002
45592
E9002
45574
W-3
5

E11001
45575
W-4
5
E12001
45583
10
E13009
45571
10
E14000
42257
2
600-017RK
21780K

D11022
45565
D12020
45566
E9002
45574
R
12

E12001
45583
12
E13009
45571
12
E14000
42257
2
600-032RK
21880K

D11022
45565
D12020
45566
E9002
45574
R
6

E11001
45575
W-4
6
E12001
45583
12
E13009
45571
12
E14000
42257
2
600-033RK
21805K

E70015
45568
E80015
45569
E90015
55962
690-W
5

E11015
55963
691-W
5
E12002
55957
10
E13007
55958
10
E14000
42257
2
500-050RK
14598K

E7002
45563
E8002
45564
E90015
55962
690-W
5

E11015
55963
691-W
5
E12002
55957
10
E13007
55958
10
E14000
42257
2
500-025RK
19377K

D11003
45579
D12003
45580
E9012
45581
W-1
6

E11013
45582
W-2
6
E12001
45583
12
E13009
45571
12
E14000
42257
2
600-018RK
21790K

E7003
45559
E8003
45560
E9004
45558
H
5

E11003
45561
I
5

E13000
45520
10
E14000
42257
2
600-019RK
21735K

FINGER RETAINER
(stainless steel)

SHORT FINGER *

MEDIUM FINGER *

LONG FINGER *

PIVOT PIN *

TORSION SPRING *
(stainless steel)

RETAINER SCREW *
(stainless steel)

REPAIR KITS
* Indicates parts included in kit

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.

Logan Oil Tools reserves the right to change or discontinue designs without notice.
When ordering, please specify:
(1) Name and number of assembly or part
(2) Finger number and code, when ordering fingers
Recommended Spare Parts:
(1) 2 Sets of Fingers
(2) 4 Sets of Torsion Springs
(3) 1 Set of Pivot Pins
(4) 4 Retainer Screws

LEGAL NOTICE
All references to Bowen part numbers in this
literature are used to identify interchangeable tools
and parts. Reference to such tools and parts does
not imply that Logan Oil Tools is a licensee or is in
any way affiliated with National Oilwell Varco. Logan Oil Tools does not sell, or offer to sell, National
Oilwell Varco (Bowen) products.

Special Notes:
(1) Code: Each finger is stenciled with a letter or letter-number code. These codes are used
in lieu of the part number because of space limitation. See the Finger Code Chart below
to cross-reference the code with the part number.
Finger Code Chart
Code
A
B
C
D
E
F
G
H

Part No.
E11006
E9005
E11005

E9001
E11000
E9013
E9004

Code
I
J
K
L
M
N
O
P

Part No.
E11003
E11014
E9014
E10003
E9010
E11010

Code
P-1
P-2
W-1
W-2
W-3
W-4
X-1
X-2

Part No.
E9007
E11008
E9012
E11013
E9002
E11001
E9019
E11020

Code
21778-W
21779-W
362-W
363-W
690-W
691-W
666-W
667-W

Part No.
E9015
E11016
E9006
E11007
E90015
E11015
E9009
E11011

Bowen is a registered trademark of National

Oilwell Varco.

Logan Reverse Circulation Junk Baskets 11

Manual C315 Logan Reverse Circulation Junk Baskets Page 11

LOGAN JUNK CATCHER ASSEMBLIES

INSIDE DIAMETER
OUTSIDE DIAMETER
LENGTH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.

3-3/4
4-15/32
2-9/16
600-083
14747-W

3-3/4
4-15/32
2-9/16
500-026
14603-W

4-3/32
4-3/4
2-1/2
600-062
21820W

4-1/16
4-7/8
2-25/32
500-014
14607-W

4-1/16
4-7/8
2-25/32
500-027
14608-W

4-13/32
5-5/32
2-13/16
600-020
28349W

4-13/32
5-5/32
1-13/32
600-067
25250-W

BODY

E7003
45559
E8003
45560
E9004
45558
H
10

E13000
45520
10
E14000
42257
2
600-083RK
14747K

E7003
45559
E8003
45560
E9004
45558
H
5

E11003
45561
I
5

E13000
45520
10
E14000
42257
2
500-026RK
14603K

D11015
45595
D12015
45596
E9019
45597
X-1
6

E11020
45598
X-2
6
E12010
45599
12
E13009
45571
12
E14000
42257
2
600-062RK
21820K

E7004
45555
E8004
45556
E9004
45558
H
12

E13000
45520
12
E14000
42257
2
500-014RK
14607K

E7004
45555
E8004
45556
E9004
45558
H
6

E9013
45557
G
6

E13000
45520
12
E14000
42257
2
500-027RK
14608K

D11004
45511
D12004
45519
E9005
45517
B
8

E11006
45516
A
4

E13000
45520
12
E14000
42257
2
600-020RK
28349K

D11019
68375
D12004
45519
E9018
68376

FINGER RETAINER
(stainless steel)

SHORT FINGER *

MEDIUM FINGER *

LONG FINGER *

PIVOT PIN *

TORSION SPRING *
(stainless steel)

RETAINER SCREW *
(stainless steel)

REPAIR KITS
* Indicates parts included in kit

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.

12

E13000
45520
12
E14000
42257
2
600-067RK
25250K

Logan Oil Tools reserves the right to change or discontinue designs without notice.
When ordering, please specify:
(1) Name and number of assembly or part
(2) Finger number and code, when ordering fingers
Recommended Spare Parts:
(1) 2 Sets of Fingers
(2) 4 Sets of Torsion Springs
(3) 1 Set of Pivot Pins
(4) 4 Retainer Screws

LEGAL NOTICE
All references to Bowen part numbers in this
literature are used to identify interchangeable tools
and parts. Reference to such tools and parts does
not imply that Logan Oil Tools is a licensee or is in
any way affiliated with National Oilwell Varco. Logan Oil Tools does not sell, or offer to sell, National
Oilwell Varco (Bowen) products.

Special Notes:
(1) Code: Each finger is stenciled with a letter or letter-number code. These codes are used
in lieu of the part number because of space limitation. See the Finger Code Chart below
to cross-reference the code with the part number.
Finger Code Chart
Code
A
B
C
D
E
F
G
H

Part No.
E11006
E9005
E11005

E9001
E11000
E9013
E9004

Bowen is a registered trademark of National

Oilwell Varco.

12 Logan Reverse Circulation Junk Baskets

Page 12 Logan Reverse Circulation Junk Baskets Manual C315

Code
I
J
K
L
M
N
O
P

Part No.
E11003
E11014
E9014
E10003
E9010
E11010

Code
P-1
P-2
W-1
W-2
W-3
W-4
X-1
X-2

Part No.
E9007
E11008
E9012
E11013
E9002
E11001
E9019
E11020

Code
21778-W
21779-W
362-W
363-W
690-W
691-W
666-W
667-W

Part No.
E9015
E11016
E9006
E11007
E90015
E11015
E9009
E11011

LOGAN JUNK CATCHER ASSEMBLIES

INSIDE DIAMETER
OUTSIDE DIAMETER
LENGTH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.

4-13/32
5-5/32
2-13/16
500-051
15130-W

4-5/16
5-5/16
2-7/8
600-065
14612-W

4-5/16
5-5/16
2-7/8
600-066
14613-W

4-17/32
5-13/32
2-7/8
500-015
19382-W

4-17/32
5-13/32
2-7/8
500-028
19383-W

4-3/4
5-5/8
2-5/8
600-021
21750W

4-13/16
5-23/32
3-1/16
500-016
14617-W

BODY

D11004
45511
D12004
45519
E9005
45517
B
12

E13000
45520
12
E14000
42257
2
500-051RK
15130K

D11018
45572
D12017
45573
E9005
45517
B
12

E13000
45520
12
E14000
42257
2
600-065RK
14612K

D11018
45572
D12017
45573
E9005
45517
B
6
E9013
45557
G
3
E11006
45516
A
3

E13000
45520
12
E14000
42257
2
600-066RK
14613K

E7005
45553
E8005
45554
E9005
45517
B
12

E13000
45520
12
E14000
42257
2
500-015RK
19382K

E7005
45553
E8005
45554
E9005
45517
B
6

E11006
45516
A
6

E13000
45520
12
E14000
42257
2
500-028RK
19383K

D11005
45584
D12005
45585
E9005
45517
B
6

E11006
45516
A
6

E13000
45520
12
E14000
42257
2
600-021RK
21750K

E7006
45512
E8006
45552
E9005
45517
B
12

E13000
45520
12
E14000
42257
2
500-016RK
14617K

FINGER RETAINER
(stainless steel)

SHORT FINGER *

MEDIUM FINGER *

LONG FINGER *

PIVOT PIN *

TORSION SPRING *
(stainless steel)

RETAINER SCREW *
(stainless steel)

REPAIR KITS
* Indicates parts included in kit

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.

Logan Oil Tools reserves the right to change or discontinue designs without notice.
When ordering, please specify:
(1) Name and number of assembly or part
(2) Finger number and code, when ordering fingers
Recommended Spare Parts:
(1) 2 Sets of Fingers
(2) 4 Sets of Torsion Springs
(3) 1 Set of Pivot Pins
(4) 4 Retainer Screws

LEGAL NOTICE
All references to Bowen part numbers in this
literature are used to identify interchangeable tools
and parts. Reference to such tools and parts does
not imply that Logan Oil Tools is a licensee or is in
any way affiliated with National Oilwell Varco. Logan Oil Tools does not sell, or offer to sell, National
Oilwell Varco (Bowen) products.

Special Notes:
(1) Code: Each finger is stenciled with a letter or letter-number code. These codes are used
in lieu of the part number because of space limitation. See the Finger Code Chart below
to cross-reference the code with the part number.
Finger Code Chart
Code
A
B
C
D
E
F
G
H

Part No.
E11006
E9005
E11005

E9001
E11000
E9013
E9004

Code
I
J
K
L
M
N
O
P

Part No.
E11003
E11014
E9014
E10003
E9010
E11010

Code
P-1
P-2
W-1
W-2
W-3
W-4
X-1
X-2

Part No.
E9007
E11008
E9012
E11013
E9002
E11001
E9019
E11020

Code
21778-W
21779-W
362-W
363-W
690-W
691-W
666-W
667-W

Part No.
E9015
E11016
E9006
E11007
E90015
E11015
E9009
E11011

Bowen is a registered trademark of National

Oilwell Varco.

Logan Reverse Circulation Junk Baskets 13

Manual C315 Logan Reverse Circulation Junk Baskets Page 13

LOGAN JUNK CATCHER ASSEMBLIES

INSIDE DIAMETER
OUTSIDE DIAMETER
LENGTH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.

4-13/16
5-23/32
3-1/16
500-029
14618-W

5-1/4
6-1/8
3-5/16
600-063
18935-W

5-3/16
6-1/4
3-5/16
14000-011
22050-W

5-3/16
6-1/4
3-5/16
600-022
21725W

5-7/16
6-3/8
3
500-017
14622-W

5-7/16
6-3/8
3-5/16
500-030
14623-W

5-5/8
6-19/32
2-7/8
600-060
21865W

BODY

E7006
45512
E8006
45552
E9005
45517
B
6

E11006
45516
A
6

E13000
45520
12
E14000
42257
2
500-029RK
14618K

D11016
45513
D12016
45527
E9005
45517
B
6
E11006
45516
A
3
E11005
45518
C
3

E13000
45520
12
E14000
42257
2
600-063RK
18935K

D11006
45550
D12006
45551
E9013
45557
G
12

E13000
45520
12
E14000
42257
2
14000-011RK
22050K

D11006
45550
D12006
45551
E9013
45557
G
6

E11005
45518
C
6

E13000
45520
12
E14000
42257
2
600-022RK
21725K

E7007
45545
E8007
45546
E9005
45517
B
14

E13000
45520
14
E14000
42257
2
500-017RK
14622K

E7007
45545
E8007
45546
E9005
45517
B
7

E11005
45518
C
7

E13000
45520
14
E14000
42257
2
500-030RK
14623K

D11013
45602
D12014
45528
E9005
45517
B
12

E13000
45520
12
E14000
42257
2
600-060RK
21865K

FINGER RETAINER
(stainless steel)

SHORT FINGER *

MEDIUM FINGER *

LONG FINGER *

PIVOT PIN *

TORSION SPRING *
(stainless steel)

* RETAINER SCREW
(stainless steel)

REPAIR KITS
* Indicates parts included in kit

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.

Logan Oil Tools reserves the right to change or discontinue designs without notice.
When ordering, please specify:
(1) Name and number of assembly or part
(2) Finger number and code, when ordering fingers
Recommended Spare Parts:
(1) 2 Sets of Fingers
(2) 4 Sets of Torsion Springs
(3) 1 Set of Pivot Pins
(4) 4 Retainer Screws

LEGAL NOTICE
All references to Bowen part numbers in this
literature are used to identify interchangeable tools
and parts. Reference to such tools and parts does
not imply that Logan Oil Tools is a licensee or is in
any way affiliated with National Oilwell Varco. Logan Oil Tools does not sell, or offer to sell, National
Oilwell Varco (Bowen) products.

Special Notes:
(1) Code: Each finger is stenciled with a letter or letter-number code. These codes are used
in lieu of the part number because of space limitation. See the Finger Code Chart below
to cross-reference the code with the part number.
Finger Code Chart
Code
A
B
C
D
E
F
G
H

Part No.
E11006
E9005
E11005

E9001
E11000
E9013
E9004

Bowen is a registered trademark of National

Oilwell Varco.

14 Logan Reverse Circulation Junk Baskets

Page 14 Logan Reverse Circulation Junk Baskets Manual C315

Code
I
J
K
L
M
N
O
P

Part No.
E11003
E11014
E9014
E10003
E9010
E11010

Code
P-1
P-2
W-1
W-2
W-3
W-4
X-1
X-2

Part No.
E9007
E11008
E9012
E11013
E9002
E11001
E9019
E11020

Code
21778-W
21779-W
362-W
363-W
690-W
691-W
666-W
667-W

Part No.
E9015
E11016
E9006
E11007
E90015
E11015
E9009
E11011

LOGAN JUNK CATCHER ASSEMBLIES

INSIDE DIAMETER
OUTSIDE DIAMETER
LENGTH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.

5-5/8
6-19/32
3-5/8
600-061
18936W

6
7
1-23/32
14000-012
21640-W

6
7
3-7/16
600-023
18725W

6-3/16
7-1/8
3-13/16
500-018
14627-W

6-3/16
7-1/8
3-13/16
500-031
14628-W

6-1/2
7-7/16
3-1/2
600-030
18720-W

7-1/16
7-7/8
4-5/16
600-034
9800W

BODY

D11014
45514
D12014
45528
E9005
45517
B
6

E11005
45518
C
6

E13000
45520
12
E14000
42257
2
600-061RK
18936K

E7014
68382
D12007
45506
E9016
68383
AH
12

E13002
45549
12
E14000
42257
2
14000-012RK
21640K

D11007
45505
D12007
45506
E9014
45508
K
6

E11014
45507
J
6

E13004
45509
12
E14000
42257
2
600-023RK
18725K

E7008
45547
E8008
45548
E9006
47670
362-W
12

E12008
45536
12
E13001
45537
12
E14000
42257
2
500-018RK
14627K

E7008
45547
E8008
45548
E9006
47670
362-W
6

E11007
47669
363-W
6
E12008
45536
12
E13001
45537
12
E14000
42257
2
500-031RK
14628K

D11020
45515
D12018
45529
E9014
45508
K
6

E11014
45507
J
6

E13004
45509
12
E14000
42257
2
600-030RK
18720K

D11023
68396
D12021
68397
E9010
45525
M
6

E10003
45510
L
6

E13002
45549
12
E14000
42257
2
600-034RK
9800K

FINGER RETAINER
(stainless steel)

SHORT FINGER *

MEDIUM FINGER *

LONG FINGER *

PIVOT PIN *

TORSION SPRING *
(stainless steel)

RETAINER SCREW *
(stainless steel)

REPAIR KITS
* Indicates parts included in kit

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.

Logan Oil Tools reserves the right to change or discontinue designs without notice.
When ordering, please specify:
(1) Name and number of assembly or part
(2) Finger number and code, when ordering fingers
Recommended Spare Parts:
(1) 2 Sets of Fingers
(2) 4 Sets of Torsion Springs
(3) 1 Set of Pivot Pins
(4) 4 Retainer Screws

LEGAL NOTICE
All references to Bowen part numbers in this
literature are used to identify interchangeable tools
and parts. Reference to such tools and parts does
not imply that Logan Oil Tools is a licensee or is in
any way affiliated with National Oilwell Varco. Logan Oil Tools does not sell, or offer to sell, National
Oilwell Varco (Bowen) products.

Special Notes:
(1) Code: Each finger is stenciled with a letter or letter-number code. These codes are used
in lieu of the part number because of space limitation. See the Finger Code Chart below
to cross-reference the code with the part number.
Finger Code Chart
Code
A
B
C
D
E
F
G
H

Part No.
E11006
E9005
E11005

E9001
E11000
E9013
E9004

Code
I
J
K
L
M
N
O
P

Part No.
E11003
E11014
E9014
E10003
E9010
E11010

Code
P-1
P-2
W-1
W-2
W-3
W-4
X-1
X-2

Part No.
E9007
E11008
E9012
E11013
E9002
E11001
E9019
E11020

Code
21778-W
21779-W
362-W
363-W
690-W
691-W
666-W
667-W

Part No.
E9015
E11016
E9006
E11007
E90015
E11015
E9009
E11011

Bowen is a registered trademark of National

Oilwell Varco.

Logan Reverse Circulation Junk Baskets 15

Manual C315 Logan Reverse Circulation Junk Baskets Page 15

LOGAN JUNK CATCHER ASSEMBLIES

INSIDE DIAMETER
OUTSIDE DIAMETER
LENGTH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.

7-3/16
8-1/8
4-5/16
14000-013
14632-W

7-3/16
8-1/8
4-5/16
600-024
14633W

7-11/16
9
4-5/8
600-025
21755W

7-13/16
9-1/32
2-5/16
14000-014
25235-W

7-13/16
9-1/32
4-5/8
500-019
18945-W

8-1/16
9-5/16
5
500-054
14637-W

8-1/16
9-5/16
5
500-032
14638-W

BODY

E7009
45521
D12008
45530
E9007
45588
N
12

E13002
45549
12
E14000
42257
2
14000-013RK
14632K

E7009
45521
D12008
45530
E9007
45588
P-1
6

E11008
45589
P-2
6

E13002
45549
12
E14000
42257
2
600-024RK
14633K

D11008
68116
D12009
68117
E11014
45507
J
6

E11018
70277
J
6

E13004
45509
12
E14000
42257
2
600-025RK
21755K

E7016
68388
E8010
45531
E9016
68383
S
12

E13004
45509
12
E14000
42257
2
14000-014RK
25235K

E7010
45522
E8010
45531
E11014
45507
J
6

E11018
70277
J
6

E13004
45509
12
E14000
42257
2
500-019RK
18945K

E7013
45523
E8013
45532
E9010
45525
M
16

E13004
45509
16
E14000
42257
2
500-054RK
154611K

E7013
45523
E8013
45532
E9010
45525
M
8
E11014
45507
J
4
E11017
68295
N
4

E13004
45509
16
E14000
42257
2
500-032RK
14638K

FINGER RETAINER
(stainless steel)

SHORT FINGER *

MEDIUM FINGER *

LONG FINGER *

PIVOT PIN *

TORSION SPRING *
(stainless steel)

RETAINER SCREW *
(stainless steel)

REPAIR KITS
* Indicates parts included in kit

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.

Logan Oil Tools reserves the right to change or discontinue designs without notice.
When ordering, please specify:
(1) Name and number of assembly or part
(2) Finger number and code, when ordering fingers
Recommended Spare Parts:
(1) 2 Sets of Fingers
(2) 4 Sets of Torsion Springs
(3) 1 Set of Pivot Pins
(4) 4 Retainer Screws

LEGAL NOTICE
All references to Bowen part numbers in this
literature are used to identify interchangeable tools
and parts. Reference to such tools and parts does
not imply that Logan Oil Tools is a licensee or is in
any way affiliated with National Oilwell Varco. Logan Oil Tools does not sell, or offer to sell, National
Oilwell Varco (Bowen) products.

Special Notes:
(1) Code: Each finger is stenciled with a letter or letter-number code. These codes are used
in lieu of the part number because of space limitation. See the Finger Code Chart below
to cross-reference the code with the part number.
Finger Code Chart
Code
A
B
C
D
E
F
G
H

Part No.
E11006
E9005
E11005

E9001
E11000
E9013
E9004

Bowen is a registered trademark of National

Oilwell Varco.

16 Logan Reverse Circulation Junk Baskets

Page 16 Logan Reverse Circulation Junk Baskets Manual C315

Code
I
J
K
L
M
N
O
P

Part No.
E11003
E11014
E9014
E10003
E9010
E11010

Code
P-1
P-2
W-1
W-2
W-3
W-4
X-1
X-2

Part No.
E9007
E11008
E9012
E11013
E9002
E11001
E9019
E11020

Code
21778-W
21779-W
362-W
363-W
690-W
691-W
666-W
667-W

Part No.
E9015
E11016
E9006
E11007
E90015
E11015
E9009
E11011

LOGAN JUNK CATCHER ASSEMBLIES

INSIDE DIAMETER
OUTSIDE DIAMETER
LENGTH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.

8-5/16
9-3/4
5
14000-015
31046-W

8-5/16
9-3/4
5
600-026
21760W

8-5/16
9-3/4
4-1/2
600-064
22000-W

8-11/16
10-3/32
5-3/32
600-027
21840W

9-1/8
10-7/16
5-3/16
500-020
14642-W

9-1/8
10-7/16
5-3/16
500-033
14643-W

10-1/8
11-3/8
6
500-021
14647-W

BODY

D11009
45576
D12010
45578
E9010
45525
M
16

E13004
45509
16
E14000
42257
2
14000-015RK
31046K

D11009
45576
D12010
45578
E9010
45525
M
8
E10003
45510
L
4
E11010
45526
N
4

E13004
45509
16
E14000
42257
2
600-026RK
21760K

D11017
45577
D12010
45578
E9010
45525
M
16

E13004
45509
16
E14000
42257
2
600-064RK
22000K

D11010
45593
D12011
45594
E11014
45507
J
8
E10003
45510
L
4
E11010
45526
N
4

E13004
45509
16
E14000
42257
2
600-027RK
21840K

E7011
45524
E8011
45533
E11014
45507
J
16

E13004
45509
16
E14000
42257
2
500-020RK
14642K

E7011
45524
E8011
45533
E11014
45507
J
8
E10003
45510
L
4
E11010
45526
N
4

E13004
45509
16
E14000
42257
2
500-033RK
14643K

E7012
45586
E8012
45587
E9009
666
666-W
16

E12012
45603
16
E13005
45604
16
E14000
42257
2
500-021RK
1464K

FINGER RETAINER
(stainless steel)

SHORT FINGER *

MEDIUM FINGER *

LONG FINGER *

PIVOT PIN *

TORSION SPRING *
(stainless steel)

RETAINER SCREW *
(stainless steel)

REPAIR KITS
* Indicates parts included in kit

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.

Logan Oil Tools reserves the right to change or discontinue designs without notice.
When ordering, please specify:
(1) Name and number of assembly or part
(2) Finger number and code, when ordering fingers
Recommended Spare Parts:
(1) 2 Sets of Fingers
(2) 4 Sets of Torsion Springs
(3) 1 Set of Pivot Pins
(4) 4 Retainer Screws

LEGAL NOTICE
All references to Bowen part numbers in this
literature are used to identify interchangeable tools
and parts. Reference to such tools and parts does
not imply that Logan Oil Tools is a licensee or is in
any way affiliated with National Oilwell Varco. Logan Oil Tools does not sell, or offer to sell, National
Oilwell Varco (Bowen) products.

Special Notes:
(1) Code: Each finger is stenciled with a letter or letter-number code. These codes are used
in lieu of the part number because of space limitation. See the Finger Code Chart below
to cross-reference the code with the part number.
Finger Code Chart
Code
A
B
C
D
E
F
G
H

Part No.
E11006
E9005
E11005

E9001
E11000
E9013
E9004

Code
I
J
K
L
M
N
O
P

Part No.
E11003
E11014
E9014
E10003
E9010
E11010

Code
P-1
P-2
W-1
W-2
W-3
W-4
X-1
X-2

Part No.
E9007
E11008
E9012
E11013
E9002
E11001
E9019
E11020

Code
21778-W
21779-W
362-W
363-W
690-W
691-W
666-W
667-W

Part No.
E9015
E11016
E9006
E11007
E90015
E11015
E9009
E11011

Bowen is a registered trademark of National

Oilwell Varco.

Logan Reverse Circulation Junk Baskets 17

Manual C315 Logan Reverse Circulation Junk Baskets Page 17

LOGAN JUNK CATCHER ASSEMBLIES

INSIDE DIAMETER
OUTSIDE DIAMETER
LENGTH
COMPLETE ASSEMBLY Logan Part No.
Bowen No.

10-1/8
11-3/8
6
500-034
14648-W

9-7/8
11-21/32
5-31/32
600-028
21770W

11-3/16
13-5/8
7-5/16
600-029
21775W

12-3/8
13-13/16
7-7/8
500-022
14652-W

12-3/8
13-13/16
7-7/8
500-035
14653-W

BODY

E7012
45586
E8012
45587
E9009
666
666-W
8

E11011
667
667-W
8
E12012
45603
16
E13005
45604
16
E14000
42257
2
500-034RK
14648K

D11011
64810
D12012
64811
E9009
666
666-W
8

E11011
667
667-W
8
E12012
45603
16
E13005
45604
16
E14000
42257
2
600-028RK
21770K

D11012
45605
D12013
45606
E9015
45607
21778-W
7

E11016
45608
21779-W
7
E12009
45609
14
E13010
45610
14
E14000
42257
2
600-029RK
21775K

E7015
68391
E8014
68392
E9017
68393

14

E12013
68394
14
E13004
45509
14
E14000
42257
2
500-022RK
14652K

E7015
68391
E8014
68392
E9017
68393

E11019
68395

7
E12013
68394
14
E13004
45509
14
E14000
42257
2
500-035RK
14653K

FINGER RETAINER
(stainless steel)

SHORT FINGER *

MEDIUM FINGER *

LONG FINGER *

PIVOT PIN *

TORSION SPRING *
(stainless steel)

RETAINER SCREW *
(stainless steel)

REPAIR KITS
* Indicates parts included in kit

Logan Part No.

Bowen No.
Logan Part No.
Bowen No.
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
Code
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.
No. Reqd
Logan Part No.
Bowen No.

Logan Oil Tools reserves the right to change or discontinue designs without notice.
When ordering, please specify:
(1) Name and number of assembly or part
(2) Finger number and code, when ordering fingers
Recommended Spare Parts:
(1) 2 Sets of Fingers
(2) 4 Sets of Torsion Springs
(3) 1 Set of Pivot Pins
(4) 4 Retainer Screws

LEGAL NOTICE
All references to Bowen part numbers in this
literature are used to identify interchangeable tools
and parts. Reference to such tools and parts does
not imply that Logan Oil Tools is a licensee or is in
any way affiliated with National Oilwell Varco. Logan Oil Tools does not sell, or offer to sell, National
Oilwell Varco (Bowen) products.

Special Notes:
(1) Code: Each finger is stenciled with a letter or letter-number code. These codes are used
in lieu of the part number because of space limitation. See the Finger Code Chart below
to cross-reference the code with the part number.
Finger Code Chart
Code
A
B
C
D
E
F
G
H

Part No.
E11006
E9005
E11005

E9001
E11000
E9013
E9004

Bowen is a registered trademark of National

Oilwell Varco.

18 Logan Reverse Circulation Junk Baskets

Page 18 Logan Reverse Circulation Junk Baskets Manual C315

Code
I
J
K
L
M
N
O
P

Part No.
E11003
E11014
E9014
E10003
E9010
E11010

Code
P-1
P-2
W-1
W-2
W-3
W-4
X-1
X-2

Part No.
E9007
E11008
E9012
E11013
E9002
E11001
E9019
E11020

Code
21778-W
21779-W
362-W
363-W
690-W
691-W
666-W
667-W

Part No.
E9015
E11016
E9006
E11007
E90015
E11015
E9009
E11011

LOGAN REVERSE CIRCULATION JUNK BASKETS

ROCK BIT CONE DIMENSIONS

MAX HEIGHT

The cone sizes shown below may be used as a guide in junk fishing operations.
Cone dimensions are the maximum for the size indicated in the middle column,
which are the nominal Hughes Christensen Company bit cone sizes.

MAX DIAMETER

2-CONE BITS
MAX DIA.
MAX HEIGHT

3-45/64
5-17/32
4-11/32
6-7/64
4-11/32
6-5/16

4-7/8
7
5-23/64
7-19/32
5-63/64
8-27/64

SIZE
3-3/4
4-1/4
4-5/8
5-1/8
5-5/8
6-1/8
6-5/8
7-1/8
7-5/8
8-1/8
8-5/8
9-1/8
9-5/8
10-1/2
11-3/4
12-5/8
13-1/2
14-1/2
16
17
18-1/2
20
22
24
26

to 4-1/8
to 4-1/2
to 5
to 5-1/2
to 6
to 6-1/2
to 7
to 7-1/2
to 8
to 8-1/2
to 9
to 9-1/2
to 9-7/8
to 11-1/2
to 12-1/2
to 13-1/8
to 14-1/4
to 15
to 17-1/2
to 18-7/8

3-CONE BITS
MAX DIA.
MAX HEIGHT
1-31/32
2-45/64
2-13/64
2-59/64
2-11/32
3-13/64
2-41/64
3-17/64
3-1/8
4-1/64
3-6/64
4-3/16
3-7/16
4-9/16
3-45/64
4-27/32
3-31/32
5-17/64
4-3/8
5-25/32
4-17/32
6-1/32
4-9/16
6-13/32
4-15/16
6-41/64
5-27/64
7-5/32
6-1/8
7-61/64
6-5/16
8-31/64
7-1/32
8-13/16
7-25/64
9-19/32
9-27/32
10-1/8
8-13/64
11-11/64
8-25/32
11-23/64
9-1/2
11-7/8
10-15/32
14-1/64
10-15/16
14-9/16
12-19/64
14-31/64

Logan Reverse Circulation Junk Baskets 19

Manual C315 Logan Reverse Circulation Junk Baskets Page 19

NOTES

20 Logan Reverse Circulation Junk Baskets

Page 20 Logan Reverse Circulation Junk Baskets Manual C315

Manual C315 Logan Reverse Circulation Junk Baskets Page 21