Honeywell V4043H Motorised Zone Valve

I N S TA L L AT I O N
INSTRUCTIONS V4043H Motorised Zone Valve
Application
The V4043H valve has been designed to control the flow of
water in iron and copper pipe systems. Although specifically
designed for small bore central heating systems, the valve
can be used in commercial and industrial applications.
Specifications
Voltage: 220-240V ~ 50Hz
Power consumption: 6W
Lead supplied: 1 metre, 5 core
Operating temperature range: +5 to +88°C
Maximum ambient temperature: +52°C
Pipe fitting sizes:
22mm & 28mm compression fitting, 3/4" & 1" BSP
Dimensions and KV values: See diagrams
Spares available
Powerhead Part No. 40003916-001
Motor Part No. 40002737-003
Ball & ‘O’ Ring Kit Part No. 272742A CARD
Installation
V4043H incorporates a
manual lever, the lever
should normally be in
‘AUTO’ position, but can be
moved to ‘MAN OPEN’ AUTO MAN
OPEN
Flow
position for system
draindown and filling Characteristics
purposes only.
Before fitting the valve, read
through the plumbing and
wiring instructions.
This product MUST be
installed by a competent person. The installation MUST
conform to I.E.E. Regulations and with The Electricity at
Work Regulations.
A Class ‘A’ switch (having contact separation of at least
3mm in all poles) must be incorporated in the fixed wiring
as a means of disconnecting the supply. The system must
be appropriately fused.
Plumbing
AUTO
OPEN
MAN
The valve may be plumbed in at any angle but must not

be mounted so that the valve head is below the
horizontal level of the pipework. In the unlikely event of a
leak a safety hazard could result.
Do not grip the valve head while making and tightening
up plumbing connections. Attach a spanner (32mm or
11/4" AF) onto the valve body at each port, whilst
tightening up the nuts. Tighten compression nuts enough
to make a watertight seal.
TAKE CARE NOT TO OVERTIGHTEN.
NOTE:
1. If using the V4043H1080 (1" BSP) or V4043H1106 (28mm), the white wire must be electrically isolated. (‘S’ Plan only.)
Wiring
The wiring diagram above shows relevant connections to a Honeywell junction box (Part No. 42002116-001).
Ensure that each numbered, lettered or coloured wire is connected to the correct terminal in the junction box.
Make sure all connections are good and all terminal screws are firmly tightened.
Notes:
a Wiring diagram shows connections to a programmer with separate control of heating and hot water.
b If single channel time clock is used, connect switched live from time clock to terminal 4 or 6 at junction box,
then link terminal 4 to terminal 6 with a link wire.
Checkout procedure 3 Confirm correct heating functions as follows:

To ensure the valve is plumbed and wired correctly, carry a Turn cylinder thermostat to minimum or switch off
out the following checks after filling the system and at programmer.
switching on the power. b Set room thermostat to maximum and programmer to
1 a Check manual lever is in ‘AUTO’ position. ‘CENTRAL HEATING ON’.
b Check programmer has power. c Boiler should fire and pump should run. Feel pipe
approximately 12" from pump (C Plan), or valve (S
c Check boiler is switched on and its thermostat set to Plan) it should get hot.
maximum.
2 Confirm correct hot water functions as follows: Completion
a Turn room thermostat to minimum setting or switch off Reset both thermostats to temperature required, normally
at programmer. 60°C for cylinder thermostat and 20°C for room thermostat.
Return programmer to ‘Auto’ or mode selected by
b Set cylinder thermostat to maximum and programmer to
householder. Full installation wiring and operating
‘HOT WATER ON’.
instructions for SUNDIAL products are included in every
c Pump should run (S Plan ONLY) and boiler should fire product pack. For special wiring diagrams or applications,
(S and C Plan). Feel pipe approximately 12" from valve contact Honeywell. ENSURE THAT VALVE HEADS HAVE
port it should get hot. FREE AIR MOVEMENT AROUND THEM.
Whilst Honeywell takes all practicable steps to design and manufacture its products to comply with the requirements of the Health and Safety at Work Act 1974, all products
must be properly used and Purchasers are reminded that their obligations under the Act are to ensure that the installation and operation of such products at a place of work
should be safe and without risk to them.
Honeywell reserve the right at any time and without notice to change any product or information contained in this publication.
The wiring diagrams and installation instructions in this publication are provided for guidance purposes when installing recognised standard systems only. Any application of
this product not shown here, or any deviation from these instructions, is neither recommended nor advised. Any such application or deviation should be referred to
Honeywell for technical assistance.
Arlington Business Park Form No. 95C-10819-1

Bracknell Rev. 5/97 KT
Berkshire RG12 1EB
Telephone: 01344 826000 Printed In Canada

Honeywell V4043H Motorised Zone Valve

Uploaded by

Copyright:

Available Formats

Honeywell V4043H Motorised Zone Valve

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Honeywell V4043H Motorised Zone Valve

Uploaded by

Copyright:

Available Formats

I N S TA L L AT I O N

INSTRUCTIONS V4043H Motorised Zone Valve

The valve may be plumbed in at any angle but must not

Checkout procedure 3 Confirm correct heating functions as follows:

Arlington Business Park Form No. 95C-10819-1

You might also like