300 101

Copyright 2006-2011 Lead2pass.com , All Rights Reserved.
Vendor: Cisco
Exam Code: 300-101
Exam Name: Implementing Cisco IP Routing (ROUTE)
Version: 16.031
Important Notice
Product
Our Product Manager keeps an eye for Exam updates by Vendors. Free update is available within
150 days after your purchase.
You can login member center and download the latest product anytime. (Product downloaded
from member center is always the latest.)
PS: Ensure you can pass the exam, please check the latest product in 2-3 days before the exam
again.
Feedback
We devote to promote the product quality and the grade of service to ensure customers interest.
If you have any suggestions, please feel free to contact us at support@lead2pass.com
If you have any questions about our product, please provide Exam Number, Version, Page
Number, Question Number, and your Login Account to us, please contact us at
technology@lead2pass.com and our technical experts will provide support in 24 hours.
Copyright
The product of each order has its own encryption code, so you should use it independently.
If anyone who share the file we will disable the free update and account access.
Any unauthorized changes will be inflicted legal punishment. We reserve the right of final
explanation for this statement.
Order ID: ****************
PayPal ID: ****************
QUESTION 1
A network engineer has been asked to ensure that the PPPoE connection is established and
authenticated using an encrypted password.
Which technology, in combination with PPPoE, can be used for authentication in this manner?
A.
B.
C.
D.
E.
PAP
dot1x
IPsec
CHAP
ESP
Answer: D
Explanation:
With PPPoE, the two authentication options are PAP and CHAP. When CHAP is enabled on an
interface and a remote device attempts to connect to it, the access server sends a CHAP packet
to the remote device. The CHAP packet requests or "challenges" the remote device to respond.
The challenge packet consists of an ID, a random number, and the host name of the local router.
When the remote device receives the challenge packet, it concatenates the ID, the remote
device's password, and the random number, and then encrypts all of it using the remote device's
password. The remote device sends the results back to the access server, along with the name
associated with the password used in the encryption process. When the access server receives
the response, it uses the name it received to retrieve a password stored in its user database. The
retrieved password should be the same password the remote device used in its encryption
process. The access server then encrypts the concatenated information with the newly retrieved
password--if the result matches the result sent in the response packet, authentication succeeds.
The benefit of using CHAP authentication is that the remote device's password is never
transmitted in clear text (encrypted). This prevents other devices from stealing it and gaining
illegal access to the ISP's network.
http://www.cisco.com/c/en/us/td/docs/ios/12_2/security/configuration/guide/fsecur_c/scfathen.html
QUESTION 2
A corporate policy requires PPPoE to be enabled and to maintain a connection with the ISP, even
if no interesting traffic exists.
Which feature can be used to accomplish this task?
A.
B.
C.
D.
E.
TCP Adjust
Dialer Persistent
PPPoE Groups
half-bridging
Peer Neighbor Route
Answer: B
Explanation:
A new interface configuration command, dialer persistent, allows a dial-on-demand routing (DDR)
dialer profile connection to be brought up without being triggered by interesting traffic. When
configured, the dialer persistent command starts a timer when the dialer interface starts up and
starts the connection when the timer expires. If interesting traffic arrives before the timer expires,
the connection is still brought up and set as persistent. The command provides a default timer
interval, or you can set a custom timer interval.
QUESTION 3
Which encapsulation supports an interface that is configured for an EVN trunk?
Get Latest & Actual 300-101 Exam's Question and Answers from Lead2pass.
http://www.lead2pass.com
A.
B.
C.
D.
E.
F.
802.1Q
ISL
PPP
Frame Relay
MPLS
HDLC
Answer: A
Explanation:
Restrictions for EVN
An EVN trunk is allowed on any interface that supports 802.1q encapsulation, such as Fast
Ethernet, Gigabit Ethernet, and port channels.
A single IP infrastructure can be virtualized to provide up to 32 virtual networks end-to-end.
If an EVN trunk is configured on an interface, you cannot configure VRF-Lite on the same
interface.
OSPFv3 is not supported; OSPFv2 is supported.
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/evn/configuration/xe-3s/evn-xe-3s-book/evnoverview.pdf
QUESTION 4
Which three characteristics are shared by subinterfaces and associated EVNs? (Choose three.)
A.
B.
C.
D.
E.
IP address
routing table
forwarding table
access control lists
NetFlow configuration
Answer: ABC
Explanation:
runk interface can carry traffic for multiple EVNs. To simplify the configuration process, all the
subinterfaces and associated EVNs have the same IP address assigned. In other words, the
trunk interface is identified by the same IP address in different EVN contexts.
This is accomplished as a result of each EVN having a unique routing and forwarding table,
thereby enabling support for overlapping IP addresses across multiple EVNs.
http://www.cisco.com/en/US/docs/ios-xml/ios/evn/configuration/xe-3sg/evn-overview.pdf
QUESTION 5
Which traffic does the following configuration allow?
ipv6 access-list cisco
permit ipv6 host 2001:DB8:0:4::32 any eq ssh
line vty 0 4
ipv6 access-class cisco in
A.
B.
C.
D.
all traffic to vty 0 4 from source 2001:DB8:0:4::32

only ssh traffic to vty 0 4 from source all
only ssh traffic to vty 0 4 from source 2001:DB8:0:4::32
all traffic to vty 0 4 from source all
Answer: C
Explanation:
Here we see that the Ipv6 access list called "cisco" is being applied to incoming VTY connections
to the router. Ipv6 access list has just one entry, which allows only the single Ipv6 IP address of
2001:DB8:0:4::32 to connect using SSH only.
QUESTION 6
For troubleshooting purposes, which method can you use in combination with the debug ip packet
command to limit the amount of output data?
A.
B.
C.
D.
E.
You can disable the IP route cache globally.

You can use the KRON scheduler.
You can use an extended access list.
You can use an IOS parser.
You can use the RITE traffic exporter.
Answer: C
Explanation:
The "debug ip packet" command generates a substantial amount of output and uses a substantial
amount of system resources. This command should be used with caution in production networks.
Always use with the access-list command to apply an extended ACL to the debug output.
http://www.cisco.com/c/en/us/support/docs/security/dynamic-multipoint-vpn-dmvpn/111976dmvpn-troubleshoot-00.html
QUESTION 7
Refer to the following access list.
access-list 100 permit ip any any log
After applying the access list on a Cisco router, the network engineer notices that the router CPU
utilization has risen to 99 percent. What is the reason for this?
A.
B.
C.
D.
A packet that matches access-list with the "log" keyword is Cisco Express Forwarding switched.
A packet that matches access-list with the "log" keyword is fast switched.
A packet that matches access-list with the "log" keyword is process switched.
A large amount of IP traffic is being permitted on the router.
Answer: C
Explanation:
ging-enabled access control lists (ACLs) provide insight into traffic as it traverses the network or
is dropped by network devices. Unfortunately, ACL logging can be CPU intensive and can
negatively affect other functions of the network device. There are two primary factors that
contribute to the CPU load increase from ACL logging: process switching of packets that match
log-enabled access control entries (ACEs) and the generation and transmission of log messages.
http://www.cisco.com/web/about/security/intelligence/acl-logging.html#4
QUESTION 8
Which address is used by the Unicast Reverse Path Forwarding protocol to validate a packet
against the routing table?
A. source address
B. destination address
C. router interface
D. default gateway
Answer: A
Explanation:
The Unicast RPF feature helps to mitigate problems that are caused by the introduction of
malformed or forged (spoofed) IP source addresses into a network by discarding IP packets that
lack a verifiable IP source address. For example, a number of common types of denial-of-service
(DoS) attacks, including Smurf and Tribal Flood Network (TFN), can take advantage of forged or
rapidly changing source IP addresses to allow attackers to thwart efforts to locate or filter the
attacks. For Internet service providers (ISPs) that provide public access, Unicast RPF deflects
such attacks by forwarding only packets that have source addresses that are valid and consistent
with the IP routing table. This action protects the network of the ISP, its customer, and the rest of
the Internet.
http://www.cisco.com/en/US/docs/ios/12_2/security/configuration/guide/scfrpf.html
QUESTION 9
What are the three modes of Unicast Reverse Path Forwarding?
A.
B.
C.
D.
strict mode, loose mode, and VRF mode

strict mode, loose mode, and broadcast mode
strict mode, broadcast mode, and VRF mode
broadcast mode, loose mode, and VRF mode
Answer: A
Explanation:
Network administrators can use Unicast Reverse Path Forwarding (Unicast RPF) to help limit the
malicious traffic on an enterprise network. This security feature works by enabling a router to
verify the reachability of the source address in packets being forwarded. This capability can limit
the appearance of spoofed addresses on a network. If the source IP address is not valid, the
packet is discarded. Unicast RPF works in one of three different modes: strict mode, loose mode,
or VRF mode. Note that not all network devices support all three modes of operation. Unicast
RPF in VRF mode will not be covered in this document.
When administrators use Unicast RPF in strict mode, the packet must be received on the
interface that the router would use to forward the return packet. Unicast RPF configured in strict
mode may drop legitimate traffic that is received on an interface that was not the router's choice
for sending return traffic. Dropping this legitimate traffic could occur when asymmetric routing
paths are present in the network.
When administrators use Unicast RPF in loose mode, the source address must appear in the
routing table. Administrators can change this behavior using the allow-default option, which
allows the use of the default route in the source verification process. Additionally, a packet that
contains a source address for which the return route points to the Null 0 interface will be dropped.
An access list may also be specified that permits or denies certain source addresses in Unicast
RPF loose mode.
Care must be taken to ensure that the appropriate Unicast RPF mode (loose or strict) is
configured during the deployment of this feature because it can drop legitimate traffic. Although
asymmetric traffic flows may be of concern when deploying this feature, Unicast RPF loose mode
is a scalable option for networks that contain asymmetric routing paths.
http://www.cisco.com/web/about/security/intelligence/unicast-rpf.html
QUESTION 10
What does the following access list, which is applied on the external interface FastEthernet 1/0 of
the perimeter router, accomplish?
router(config)#access-list 101 deny ip 10.0.0.0 0.255.255.255 any log

router (config)#access-list 101 deny ip 192.168.0.0 0.0.255.255 any log
router (config)#access-list 101 deny ip 172.16.0.0 0.15.255.255 any log
router (config)#access-list 101 permit ip any any
router (config)#interface fastEthernet 1/0
router (config-if)#ip access-group 101 in
A. It prevents incoming traffic from IP address ranges 10.0.0.0-10.0.0.255, 172.16.0.0172.31.255.255, 192.168.0.0-192.168.255.255 and logs any intrusion attempts.
B. It prevents the internal network from being used in spoofed denial of service attacks and logs any
exit to the Internet.
C. It filters incoming traffic from private addresses in order to prevent spoofing and logs any intrusion
attempts.
D. It prevents private internal addresses to be accessed directly from outside.
Answer: C
Explanation:
The private IP address ranges defined in RFC 1918 are as follows:
10.0.0.0 -- 10.255.255.255
172.16.0.0 -- 172.31.255.255
192.168.0.0 -- 192.168.255.255
These IP addresses should never be allowed from external networks into a corporate network as
they would only be able to reach the network from the outside via routing problems or if the IP
addresses were spoofed. This ACL is used to prevent all packets with a spoofed reserved private
source IP address to enter the network. The log keyword also enables logging of this intrusion
attempt.
QUESTION 11
Refer to the following command:
router(config)# ip http secure-port 4433
Which statement is true?
A.
B.
C.
D.
The router will listen on port 4433 for HTTPS traffic.

The router will listen on port 4433 for HTTP traffic.
The router will never accept any HTTP and HTTPS traffic.
The router will listen to HTTP and HTTP traffic on port 4433.
Answer: A
Explanation:
To set the secure HTTP (HTTPS) server port number for listening, use the ip http secure-port
command in global configuration mode. To return the HTTPS server port number to the default,
use the no form of this command.
Ip http secure-port port-number
no ip http secure-port
Syntax Description
port-number
Integer in the range of 0 to 65535 is accepted, but the port number must be higher than 1024
unless the default is used. The default is 443.
http://www.cisco.com/en/US/docs/ios-xml/ios/https/command/nm-https-cr-clsh.html#wp3612805529
QUESTION 12
A network engineer is configuring SNMP on network devices to utilize one-way SNMP
notifications. However, the engineer is not concerned with authentication or encryption.
Which command satisfies the requirements of this scenario?
A.
B.
C.
D.
router(config)#snmp-server host 172.16.201.28 traps version 2c CISCORO

router(config)#snmp-server host 172.16.201.28 informs version 2c CISCORO
router(config)#snmp-server host 172.16.201.28 traps version 3 auth CISCORO
router(config)#snmp-server host 172.16.201.28 informs version 3 auth CISCORO
Answer: A
Explanation:
Most network admins and engineers are familiar with SNMPv2c which has become the dominant
SNMP version of the past decade. It's simple to configure on both the router/switch-side and just
as easy on the network monitoring server. The problem of course is that the SNMP statistical
payload is not encrypted and authentication is passed in cleartext. Most companies have decided
that the information being transmitted isn't valuable enough to be worth the extra effort in
upgrading to SNMPv3, but I would suggest otherwise.
Like IPv4 to Ipv6, there are some major changes under the hood. SNMP version 2 uses
community strings (think cleartext passwords, no encryption) to authenticate polling and trap
delivery. SNMP version 3 moves away from the community string approach in favor of userbased authentication and view-based access control. The users are not actual local user
accounts, rather they are simply a means to determine who can authenticate to the device. The
view is used to define what the user account may access on the IOS device. Finally, each user is
added to a group, which determines the access policy for its users. Users, groups, views.
http://www.ccnpguide.com/snmp-version-3/
QUESTION 13
When using SNMPv3 with NoAuthNoPriv, which string is matched for authentication?
A.
B.
C.
D.
username
password
community-string
encryption-key
Answer: A
Explanation:
The following security models exist: SNMPv1, SNMPv2, SNMPv3. The following security levels
exits: "noAuthNoPriv" (no authentiation and no encryption ?noauth keyword in CLI),
"AuthNoPriv109thernet109ationre authenticated but not encrypted ?auth keyword in CLI),
"AuthPriv" (messages are authenticated and encrypted ?priv keyword in CLI). SNMPv1 and
SNMPv2 models only support the "noAuthNoPriv" model since they use plain community string to
match the incoming packets. The SNMPv3 implementations could be configured to use either of
the models on per-group basis (in case if "noAuthNoPriv" is configured, username serves as a
replacement for community string).
http://blog.ine.com/2008/07/19/snmpv3-tutorial/
QUESTION 14
After a recent DoS attack on a network, senior management asks you to implement better logging
functionality on all IOS-based devices.
Which two actions can you take to provide enhanced logging results? (Choose two.)
A.
B.
C.
D.
E.
Use the msec option to enable service time stamps.

Increase the logging history.
Set the logging severity level to 1.
Specify a logging rate limit.
Disable event logging on all noncritical items.
Answer: AB
Explanation:
The optional msec keyword specifies the date/time format should include milliseconds. This can
aid in pinpointing the exact time of events, or to correlate the order that the events happened. To
limit syslog messages sent to the router's history table and to an SNMP network management
station based on severity, use the logging history command in global configuration mode. By
default, Cisco devices Log error messages of severity levels 0 through 4 (emergency, alert,
critical, error, and warning levels); in other words, "saving level warnings or higher." By increasing
the severity level, more granular monitoring can occur, and SNMP messages will be sent by the
less sever (5-7) messages.
QUESTION 15
A network engineer finds that a core router has crashed without warning. In this situation, which
feature can the engineer use to create a crash collection?
A.
B.
C.
D.
E.
secure copy protocol

core dumps
warm reloads
SNMP
NetFlow
Answer: B
Explanation:
When a router crashes, it is sometimes useful to obtain a full copy of the memory image (called a
core dump) to identify the cause of the crash. Core dumps are generally very useful to your
technical support representative.
Four basic ways exist for setting up the router to generate a core dump:
Using Trivial File Transfer Protocol (TFTP)
Using File Transfer Protocol (FTP)
Using remote copy protocol (rcp)
Using a Flash disk
http://www.cisco.com/en/US/docs/internetworking/troubleshooting/guide/tr19aa.html
QUESTION 16
A network engineer is trying to implement broadcast-based NTP in a network and executes the
ntp broadcast client command. Assuming that an NTP server is already set up, what is the result
of the command?
A.
B.
C.
D.
It enables receiving NTP broadcasts on the interface where the command was executed.
It enables receiving NTP broadcasts on all interfaces globally.
It enables a device to be an NTP peer to another device.
It enables a device to receive NTP broadcast and unicast packets.
Answer: A
Explanation:
The NTP service can be activated by entering any ntp command. When you use the ntp
broadcast client command, the NTP service is activated (if it has not already been activated) and
the device is configured to receive NTP broadcast packets on a specified interface
simultaneously.
Command
Description
ntp broadcast client
Allows the system to receive NTP broadcast packets on an interface.
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/bsm/command/bsm-xe-3se-3850-cr-book/bsmxe-3se-3850-cr-book_chapter_00.html
QUESTION 17
Which three TCP enhancements can be used with TCP selective acknowledgments? (Choose
three.)
A.
B.
C.
D.
E.
F.
header compression
explicit congestion notification
keepalive
time stamps
TCP path discovery
MTU window
Answer: BCD
Explanation:
TCP Selective Acknowledgment
The TCP Selective Acknowledgment feature improves performance if multiple packets are lost
from one TCP window of data.
Prior to this feature, because of limited information available from cumulative acknowledgments,
a TCP sender could learn about only one lost packet per-round-trip time. An aggressive sender
could choose to resend packets early, but such re-sent segments might have already been
successfully received.
The TCP selective acknowledgment mechanism helps improve performance. The receiving TCP
host returns selective acknowledgment packets to the sender, informing the sender of data that
has been received. In other words, the receiver can acknowledge packets received out of order.
The sender can then resend only missing data segments (instead of everything since the first
missing packet).
Prior to selective acknowledgment, if TCP lost packets 4 and 7 out of an 8-packet window, TCP
would receive acknowledgment of only packets 1, 2, and 3. Packets 4 through 8 would need to be
re-sent. With selective acknowledgment, TCP receives acknowledgment of packets 1, 2, 3, 5, 6,
and 8. Only packets 4 and 7 must be re-sent.
TCP selective acknowledgment is used only when multiple packets are dropped within one TCP
window. There is no performance impact when the feature is enabled but not used. Use the ip tcp
selective-ack command in global configuration mode to enable TCP selective acknowledgment.
Refer to RFC 2018 for more details about TCP selective acknowledgment.
TCP Time Stamp
The TCP time-stamp option provides improved TCP round-trip time measurements. Because the
time stamps are always sent and echoed in both directions and the time-stamp value in the
header is always changing, TCP header compression will not compress the outgoing packet. To
allow TCP header compression over a serial link, the TCP time-stamp option is disabled. Use the
ip tcp timestamp command to enable the TCP time-stamp option.
TCP Explicit Congestion Notification
The TCP Explicit Congestion Notification (ECN) feature allows an intermediate router to notify
end hosts of impending network congestion. It also provides enhanced support for TCP sessions
associated with applications, such as Telnet, web browsing, and transfer of audio and video data
that are sensitive to delay or packet loss. The benefit of this feature is the reduction of delay and
packet loss in data transmissions. Use the ip tcp ecn command in global configuration mode to
enable TCP ECN.
TCP Keepalive Timer
The TCP Keepalive Timer feature provides a mechanism to identify dead connections. When a
TCP connection on a routing device is idle for too long, the device sends a TCP keepalive packet
to the peer with only the Acknowledgment (ACK) flag turned on. If a response packet (a TCP
ACK packet) is not received after the device sends a specific number of probes, the connection is
considered dead and the device initiating the probes frees resources used by the TCP
connection.
QUESTION 18
A network administrator uses IP SLA to measure UDP performance and notices that packets on
one router have a higher one-way delay compared to the opposite direction.
Which UDP characteristic does this scenario describe?
A.
B.
C.
D.
E.
latency
starvation
connectionless communication
nonsequencing unordered packets
jitter
Answer: A
Explanation:
Cisco IOS IP SLAs provides a proactive notification feature with an SNMP trap. Each
measurement operation can monitor against a pre-set performance threshold. Cisco IOS IP SLAs
generates an SNMP trap to alert management applications if this threshold is crossed. Several
SNMP traps are available: round trip time, average jitter, one-way latency, jitter, packet loss,
MOS, and connectivity tests.
Here is a partial sample output from the IP SLA statistics that can be seen:
router#show ip sla statistics 1
Round Trip Time (RTT) for Index 55
Latest RTT: 1 ms
Latest operation start time: *23:43:31.845 UTC Thu Feb 3 2005 Latest operation return code: OK
RTT Values:
Number Of RTT: 10 RTT Min/Avg/Max: 1/1/1 milliseconds Latency one-way time:
Number of Latency one-way Samples: 0
Source to Destination Latency one way Min/Avg/Max: 0/0/0 milliseconds Destination to Source
Latency one way Min/Avg/Max: 0/0/0 milliseconds
http://www.cisco.com/en/US/technologies/tk648/tk362/tk920/technologies_white_paper09186a00
802d5efe.html
QUESTION 19
Under which condition does UDP dominance occur?
A.
B.
C.
D.
when TCP traffic is in the same class as UDP

when UDP flows are assigned a lower priority queue
when WRED is enabled
when ACLs are in place to block TCP traffic
Answer: A
10
Explanation:
Mixing TCP with UDP
It is a general best practice to not mix TCP-based traffic with UDP-based traffic (especially
Streaming-Video) within a single service-provider class because of the behaviors of these
protocols during periods of congestion. Specifically, TCP transmitters throttle back flows when
drops are detected. Although some UDP applications have application-level windowing, flow
control, and retransmission capabilities, most UDP transmitters are completely oblivious to drops
and, thus, never lower transmission rates because of dropping. When TCP flows are combined
with UDP flows within a single service-provider class and the class experiences congestion, TCP
flows continually lower their transmission rates, potentially giving up their bandwidth to UDP flows
that are oblivious to drops. This effect is called TCP starvation/UDP dominance.
TCP starvation/UDP dominance likely occurs if (TCP-based) Mission-Critical Data is assigned to
the same service-provider class as (UDP-based) Streaming-Video and the class experiences
sustained congestion. Even if WRED is enabled on the service-provider class, the same behavior
would be observed because WRED (for the most part) manages congestion only on TCP-based
flows.
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/WAN_and_MAN/QoS_SRND/QoSSRND-Book/VPNQoS.html
QUESTION 20
PPPoE is composed of which two phases?
A.
B.
C.
D.
Active Authentication Phase and PPP Session Phase

Passive Discovery Phase and PPP Session Phase
Active Authorization Phase and PPP Session Phase
Active Discovery Phase and PPP Session Phase
Answer: D
QUESTION 21
Which statement is true about the PPP Session Phase of PPPoE?
A. PPP options are negotiated and authentication is not performed.
Once the link setup is completed, PPPoE functions as a Layer 3 encapsulation method that
allows data to be transferred over the PPP link within PPPoE headers.
B. PPP options are not negotiated and authentication is performed.
C. PPP options are automatically enabled and authorization is performed.
allows data to be encrypted over the PPP link within PPPoE headers.
D. PPP options are negotiated and authentication is performed.
Answer: D
Explanation:
http://www.cisco.com/c/en/us/td/docs/security/asa/asa92/configuration/vpn/asa-vpn-cli/vpnpppoe.html
QUESTION 22
Which type of traffic does DHCP snooping drop?
11
A.
B.
C.
D.
discover messages
DHCP messages where the source MAC and client MAC do not match
traffic from a trusted DHCP server to client
DHCP messages where the destination MAC and client MAC do not match
Answer: B
Explanation:
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6500/ios/122SX/configuration/guide/book/snoodhcp.html
QUESTION 23
Refer to the exhibit. Which command only announces the 1.2.3.0/24 network out of FastEthernet
0/0?
A.
B.
C.
D.
distribute list 1 out

distribute list 1 out FastEthernet0/0
distribute list 2 out
distribute list 2 out FastEthernet0/0
Answer: D
Explanation:
Access list 2 is more specific, allowing only 1.2.3.0/24, whereas access list 1 permits all 1.0.0.0/8
networks. This question also asks us to apply this distribute list only to the outbound direction of
the fast Ethernet 0/0 interface, so the correct command is "distribute list 2 out FastEthernet0/0."
QUESTION 24
Which prefix is matched by the command ip prefix-list name permit 10.8.0.0/16 ge 24 le 24?
A.
B.
C.
D.
10.9.1.0/24
10.8.0.0/24
10.8.0.0/16
10.8.0.0/23
Answer: B
Explanation:
With prefix lists, the ge 24 term means greater than or equal to a /24 and the le 24 means less
than or equal to /24, so only a /24 is both greater than or equal to 24 and less than or equal to 24.
This translates to any prefix in the 10.8.x.0/24 network, where X is any value in the 0-255 range.
Only the choice of 10.8.0.0.24 matches this.
12
QUESTION 25
Router A and Router B are configured with IPv6 addressing and basic routing capabilities using
OSPFv3. The networks that are advertised from Router A do not show up in Router B's routing
table. After debugging IPv6 packets, the message "not a router" is found in the output.
Why is the routing information not being learned by Router B?
A. OSPFv3 timers were adjusted for fast convergence.
B. The networks were not advertised properly under the OSPFv3 process.
C. An IPv6 traffic filter is blocking the networks from being learned via the Router B interface that is
connected to Router A.
D. IPv6 unicast routing is not enabled on Router A or Router B.
Answer: D
Explanation:
http://www.cisco.com/c/en/us/td/docs/ios/ipv6/command/reference/ipv6_book/ipv6_16.html
QUESTION 26
After you review the output of the command show ipv6 interface brief, you see that several IPv6
addresses have the 16-bit hexadecimal value of "FFFE" inserted into the address.
Based on this information, what do you conclude about these IPv6 addresses?
A.
B.
C.
D.
E.
IEEE EUI-64 was implemented when assigning IPv6 addresses on the device.
The addresses were misconfigured and will not function as intended.
IPv6 addresses containing "FFFE" indicate that the address is reserved for multicast.
The IPv6 universal/local flag (bit 7) was flipped.
IPv6 unicast forwarding was enabled, but IPv6 Cisco Express Forwarding was disabled.
Answer: A
Explanation:
Extended Unique Identifier (EUI), as per RFC2373, allows a host to assign iteslf a unique 64-Bit
IP Version 6 interface identify them EUI-64). This feature is a key benefit over IPv4 as it
eliminates the need of manual configuration or DHCP as in the world of IPv4. The IPv6 EUI-64
format address is obtained through the 48-bit MAC address. The Mac address is first separated
into two 24-bits, with one being OUI (Organizationally Unique Identifier) and the other being NIC
specific. The 16-bit 0xFFFE is then inserted between these two 24-bits to for the 64-bit EUI
address. IEEE has chosen FFFE as a reserved value which can only appear in EUI-64 generated
from the EUI-48 MAC address.
https://supportforums.cisco.com/document/100566/understanding-ipv6-eui-64-bit-address
QUESTION 27
A packet capture log indicates that several router solicitation messages were sent from a local
host on the IPv6 segment. What is the expected acknowledgment and its usage?
A. Router acknowledgment messages will be forwarded upstream, where the DHCP server will
allocate addresses to the local host.
B. Routers on the IPv6 segment will respond with an advertisement that provides an external path
from the local subnet, as well as certain data, such as prefix discovery.
C. Duplicate Address Detection will determine if any other local host is using the same IPv6 address
for communication with the IPv6 routers on the segment.
D. All local host traffic will be redirected to the router with the lowest ICMPv6 signature, which is
statically defined by the network administrator.
13
Answer: B
Explanation:
Router Advertisements (RA) are sent in response to router solicitation messages. Router
solicitation messages, which have a value of 133 in the Type field of the ICMP packet header, are
sent by hosts at system startup so that the host can immediately autoconfigure without needing to
wait for the next scheduled RA message. Given that router solicitation messages are usually sent
by hosts at system startup (the host does not have a configured unicast address), the source
address in router solicitation messages is usually the unspecified Ipv6 address (0:0:0:0:0:0:0:0). If
the host has a configured unicast address, the unicast address of the interface sending the router
solicitation message is used as the source address in the message. The destination address in
router solicitation messages is the all-routers multicast address with a scope of the link. When an
RA is sent in response to a router solicitation, the destination address in the RA message is the
unicast address of the source of the router solicitation message. RA messages typically include
the following information:
One or more onlink Ipv6 prefixes that nodes on the local link can use to automatically configure
their Ipv6 addresses
Lifetime information for each prefix included in the advertisement
Sets of flags that indicate the type of autoconfiguration (stateless or stateful) that can be
completed
Default router information (whether the router sending the advertisement should be used as a
default router and, if so, the amount of time (in seconds) the router should be used as a default
router)
Additional information for hosts, such as the hop limit and MTU a host should use in packets that
it originates
http://www.cisco.com/c/en/us/td/docs/ios/ipv6/configuration/guide/12_4t/ipv6_12_4t_book/ip6addrg_bsc_con.html
QUESTION 28
A user is having issues accessing file shares on a network. The network engineer advises the
user to open a web browser, input a prescribed IP address, and follow the instructions.
After doing this, the user is able to access company shares.
Which type of remote access did the engineer enable?
A.
B.
C.
D.
EZVPN
IPsec VPN client access
VPDN client access
SSL VPN client access
Answer: D
Explanation:
The Cisco AnyConnect VPN Client provides secure SSL connections to the security appliance for
remote users. Without a previously installed client, remote users enter the IP address in their
browser of an interface configured to accept SSL VPN connections. Unless the security appliance
is configured to redirect http:// requests to https://, users must enter the URL in the form
https://<address>.
After entering the URL, the browser connects to that interface and displays the login screen. If the
user satisfies the login and authentication, and the security appliance identifies the user as
requiring the client, it downloads the client that matches the operating system of the remote
computer. After downloading, the client installs and configures itself, establishes a secure SSL
connection and either remains or uninstalls itself (depending on the security appliance
configuration) when the connection terminates.
http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generationfirewalls/100936-asa8x-split-tunnel-anyconnect-config.html
14
QUESTION 29
Which Cisco IOS VPN technology leverages IPsec, mGRE, dynamic routing protocol, NHRP, and
Cisco Express Forwarding?
A.
B.
C.
D.
FlexVPN
DMVPN
GETVPN
Cisco Easy VPN
Answer: B
Explanation:
Dynamic Multipoint Virtual Private Network (DMVPN) is a dynamic tunneling form of a virtual
private network (VPN) supported on Cisco IOS-based routers and Unix-like Operating Systems
based on the standard protocols, GRE, NHRP and Ipsec. This DMVPN provides the capability for
creating a dynamic-mesh VPN network without having to pre-configure (static) all possible tunnel
end-point peers, including Ipsec (Internet Protocol Security) and ISAKMP (Internet Security
Association and Key Management Protocol) peers. DMVPN is initially configured to build out a
hub-and-spoke network by statically configuring the hubs (VPN headends) on the spokes, no
change in the configuration on the hub is required to accept new spokes. Using this initial huband-spoke network, tunnels between spokes can be dynamically built on demand (dynamicmesh) without additional configuration on the hubs or spokes. This dynamic-mesh capability
alleviates the need for any load on the hub to route data between the spoke networks.
DMVPN is combination of the following technologies:
http://en.wikipedia.org/wiki/Dynamic_Multipoint_Virtual_Private_Network
QUESTION 30
A network engineer is configuring a solution to allow failover of HSRP nodes during maintenance
windows, as an alternative to powering down the active router and letting the network respond
accordingly. Which action will allow for manual switching of HSRP nodes?
A.
B.
C.
D.
Track the up/down state of a loopback interface and shut down this interface during maintenance.
Adjust the HSRP priority without the use of preemption.
Disable and enable all active interfaces on the active HSRP node.
Enable HSRPv2 under global configuration, which allows for maintenance mode.
Answer: A
Explanation:
The standby track command allows you to specify another interface on the router for the HSRP
process to monitor in order to alter the HSRP priority for a given group. If the line protocol of the
specified interface goes down, the HSRP priority is reduced. This means that another HSRP
router with higher priority can become the active router if that router has standby preempt
enabled. Loopback interfaces can be tracked, so when this interface is shut down the HSRP
priority for that router will be lowered and the other HSRP router will then become the active one.
http://www.cisco.com/c/en/us/support/docs/ip/hot-standby-router-protocol-hsrp/13780-6.html
QUESTION 31
A network engineer is notified that several employees are experiencing network performance
related issues, and bandwidth-intensive applications are identified as the root cause. In order to
identify which specific type of traffic is causing this slowness, information such as the
source/destination IP and Layer 4 port numbers is required.
Which feature should the engineer use to gather the required information?
15
A.
B.
C.
D.
E.
SNMP
Cisco IOS EEM
NetFlow
Syslog
WCCP
Answer: C
Explanation:
NetFlow Flows Key Fields
A network flow is identified as a unidirectional stream of packets between a given source and
destination--both are defined by a network-layer IP address and transport-layer source and des-nation port numbers. Specifically, a flow is identified as the combination of the following key
fields:
http://www.cisco.com/en/US/docs/ios-xml/ios/netflow/configuration/12-4t/cfg-nflow-data-expt.html
QUESTION 32
An organization decides to implement NetFlow on its network to monitor the fluctuation of traffic
that is disrupting core services. After reviewing the output of NetFlow, the network engineer is
unable to see OUT traffic on the interfaces. What can you determine based on this information?
A.
B.
C.
D.
Cisco Express Forwarding has not been configured globally.

NetFlow output has been filtered by default.
Flow Export version 9 is in use.
The command ip flow-capture fragment-offset has been enabled.
Answer: A
Explanation:
https://blogs.manageengine.com/network-2/netflowanalyzer/2010/05/19/need-for-cef-in-netflowdata-export.html
QUESTION 33
A network engineer has left a NetFlow capture enabled over the weekend to gather information
regarding excessive bandwidth utilization. The following command is entered:
switch#show flow exporter Flow_Exporter-1
What is the expected output?
A.
B.
C.
D.
configuration of the specified flow exporter

current status of the specified flow exporter
status and statistics of the specified flow monitor
configuration of the specified flow monitor
Answer: B
Explanation:
show flow exporter exporter-name
Example:
Device# show flow exporter FLOW_EXPORTER-1
(Optional) Displays the current status of the specified flow exporter
16
http://www.cisco.com/en/US/docs/ios-xml/ios/fnetflow/configuration/15-mt/cfg-de-fnflowexprts.html
QUESTION 34
A company's corporate policy has been updated to require that stateless, 1-to-1, and IPv6 to IPv6
translations at the Internet edge are performed.
What is the best solution to ensure compliance with this new policy?
A.
B.
C.
D.
E.
NAT64
NAT44
NATv6
NPTv4
NPTv6
Answer: E
Explanation:
NPTv6 provides a mechanism to translate the private internal organization prefixes to public
globally reachable addresses. The translation mechanism is stateless and provides a 1:1
relationship between the internal addresses and external addresses. The use cases for NPTv6
outlined in the RFC include peering with partner networks, multi homing, and redundancy and
load sharing.
http://www.cisco.com/c/dam/en/us/td/docs/solutions/SBA/August2012/Cisco_SBA_BN_IPv6Addr
essingGuide-Aug2012.pdf
QUESTION 35
Which two functions are completely independent when implementing NAT64 over NAT-PT?
(Choose two.)
A.
B.
C.
D.
E.
DNS
NAT
port redirection
stateless translation
session handling
Answer: AB
Explanation:
Work Address Translation IPv6 to IPv4, or NAT64, technology facilitates communication between
IPv6-only and IPv4-only hosts and networks (whether in a transit, an access, or an edge
network). This solution allows both enterprises and ISPs to accelerate IPv6 adoption while
simultaneously handling IPv4 address depletion. The DnS64 and NAT64 functions are completely
separated, which is essential to the superiority of NAT64 over NAT-PT.
http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/enterprise-ipv6solution/white_paper_c11-676278.html
QUESTION 36
Which two methods of deployment can you use when implementing NAT64? (Choose two.)
A.
B.
C.
D.
stateless
stateful
manual
automatic
17
E. static
F. functional
G. dynamic
Answer: AB
Explanation:
While stateful and stateless NAT64 perform the task of translating IPv4 packets into IPv6 packets
and vice versa, there are important differences. The following table provides a high-level overview
of the most relevant differences.
http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/enterprise-ipv6solution/white_paper_c11-676277.html
QUESTION 37
Which NetFlow component is applied to an interface and collects information about flows?
A.
B.
C.
D.
flow monitor
flow exporter
flow sampler
flow collector
Answer: A
Explanation:
Flow monitors are the NetFlow component that is applied to interfaces to perform network traffic
monitoring. Flow monitors consist of a record and a cache. You add the record to the flow monitor
after you create the flow monitor. The flow monitor cache is automatically created at the time the
flow monitor is applied to the first interface. Flow data is collected from the network traffic during
the monitoring process based on the key and nonkey fields in the record, which is configured for
the flow monitor and stored in the flow monitor cache.
http://www.cisco.com/c/en/us/td/docs/ios/fnetflow/command/reference/fnf_book/fnf_01.html#wp13
14030
QUESTION 38
Refer to the exhibit. Which statement about the output of the show flow-sampler command is
true?
A. The sampler matched 10 packets, each packet randomly chosen from every group of 100
packets.
B. The sampler matched 10 packets, one packet every 100 packets.
C. The sampler matched 10 packets, each one randomly chosen from every 100-second interval.
D. The sampler matched 10 packets, one packet every 100 seconds.
Answer: A
Explanation:
The sampling mode determines the algorithm that selects a subset of traffic for NetFlow
processing. In the random sampling mode that Random Sampled NetFlow uses, incoming
packets are randomly selected so that one out of each n sequential packets is selected on
average for NetFlow processing.
18
http://www.cisco.com/c/en/us/td/docs/ios/12_0s/feature/guide/nfstatsa.html#wp1084291
QUESTION 39
What is the result of the command ip flow-export destination 10.10.10.1 5858?
A. It configures the router to export cache flow information to IP 10.10.10.1 on port UDP/5858.
B. It configures the router to export cache flow information about flows with destination IP 10.10.10.1
and port UDP/5858.
C. It configures the router to receive cache flow information from IP 10.10.10.1 on port UDP/5858.
D. It configures the router to receive cache flow information about flows with destination IP
10.10.10.1 and port UDP/5858.
Answer: A
Explanation:
http://www.cisco.com/c/en/us/td/docs/ios/12_0s/feature/guide/12s_mdnf.html#wp1023091
QUESTION 40
Lab Simulation 1 - OSPF
Route.com is a small IT corporation that is attempting to implement the network shown in the
exhibit. Currently the implementation is partially completed. OSPF has been configured on
routers Chicago and NewYork. The S0/0 interface on Chicago and the S0/1 interface on NewYork
are in Area 0. The loopback0 interface on NewYork is in Area 1.
However, they cannot ping from the serial interface of the Seattle router to the loopback interface
of the NewYork router.
You have been asked to complete the implementation to allow this ping.
ROUTE.com's corporate implementation guidelines require:
- The OSPF process ID for all routers must be 10.
- The routing protocol for each interface must be enabled under the
routing process.
- The routing protocol must be enabled for each interface using the
most specific wildcard mask possible.
- The serial link between Seattle and Chicago must be in OSPF area 21.
- OSPF area 21 must not receive any inter-area or external routes.
Network Information
Seattle
S0/0 192.168.16.5/30 - Link between Seattle and Chicago
Secret Password: cisco
Chicago
S0/0 192.168.54.9/30 - Link between Chicago and NewYork
S0/1 192.168.16.6/30 - Link between Seattle and Chicago Secre
Password: cisco
NewYork
S0/1 192.168.54.10/30 - Link between Chicago and NewYork
Loopback0 172.16.189.189
Secret Password: cisco
19
Answer:
Note: In actual exam, the IP addressing, OSPF areas and process ID, and router hostnames may
change, but the overall solution is the same.
Seattle's S0/0 IP Address is 192.168.16.5/30. So, we need to find the network address and
wildcard mask of 192.168.16.5/30 in order to configure the OSPF.
IP Address: 192.168.16.5 /30
Subnet Mask: 255.255.255.252
Here subtract 252 from 2565, 256-252 = 4, hence the subnets will increment by 4.
First, find the 4th octet of the Network Address:
The 4th octet of IP address (192.168.16.5) belongs to subnet 1 (4 to 7).

Network Address: 192.168.16.4
Broadcast Address: 192.168.16.7
Lets find the wildcard mask of /30.
Subnet Mask: (Network Bits 1's, Host Bits
Lets find the wildcard mask of /30.
0's)
20
Now we configure OSPF using process ID 10 (note the process ID may change to something else
in real exam).
Seattle> enable
Password:
Seattle# conf t
Seattle(config)# router ospf 10
Seattle(config-router)# network 192.168.16.4 0.0.0.3 area 21
One of the tasks states that area 21 should not receive any external or inter-area routes (except
the default route).
Seattle(config-router)# area 21 stub
Seattle(config-router)# end
Seattle# copy run start
Chicago Configuration:
Chicago> enable
Password: cisco
Chicago# conf t
Chicago(config)# router ospf 10
We need to add Chicago's S0/1 interface to Area 21
Chicago(config-router)# network 192.168.16.4 0.0.0.3 area 21
Again, area 21 should not receive any external or inter-area routes (except the default route).
In order to accomplish this, we must stop LSA Type 5 if we don't want to send external routes.
And if we don't want to send inter-area routes, we have to stop LSA Type 3 and Type 4.
Therefore we want to configure area 21 as a totally stubby area.
Chicago(config-router)# area 21 stub no-summary
Chicago(config-router)# end
Chicago# copy run start
21
The other interface on the Chicago router is already configured correctly in this scenario, as well
as the New York router so there is nothing that needs to be done on that router.
QUESTION 41
Lab Simulation 2 - EIGRP Stub
Answer:
First we have to figure out why R3 and R4 can not communicate with each other. Use the show
running-config command on router R3
22
Notice that R3 is configured as a stub receive-only router. The receive-only keyword will restrict
the router from sharing any of its routes with any other router in that EIGRP autonomous system.
This keyword will also prevent any type of route from being sent.
Therefore we will remove this command and replace it with the eigrp stub command:
R3# configure terminal
R3(config)# router eigrp 123
R3(config-router)# no eigrp stub receive-only
R3(config-router)# eigrp stub
R3(config-router)# end
Now R3 will send updates containing its connected and summary routes to other routers. Notice
that the eigrp stub command equals to the eigrp stub connected summary because the
connected and summary options are enabled by default.
Next we will configure router R3 so that it has only 2 subnets of 10.0.0.0 network. Use the show
ip route command on R3 to view its routing table
R3# show ip route
23
Because we want the routing table of R3 only have 2 subnets so we have to summary subnetworks at the interface which is connected with R3, the s0/0 interface of R4.
There is one interesting thing about the output of the show ip route shown above: the 10.2.3.0/24,
which is a directly connected network of R3. We cant get rid of it in the routing table no matter
what technique we use to summary the networks. Therefore, to make the routing table of R3 has
only 2 subnets we have to summary other subnets into one subnet.
In the output if we dont see the summary line (like 10.0.0.0/8 is a summary) then we should
use the command ip summary-address eigrp 123 10.2.0.0 255.255.0.0 so that all the ping can
work well.
In conclusion, we will use the ip summary-address eigrp 123 10.2.0.0 255.255.0.0 at the interface
s0/0 of R4 to summary.
R4> enable
R4(config)# interface s0/0
R4(config-if)# ip summary-address eigrp 123 10.2.0.0 255.255.0.0
Now we jump back to R3 and use the show ip route command to verify the effect, the output is
shown below:
(But please notice that the ip addresses and the subnet masks in your real exam might be
different so you might use different ones to solve this question) Just for your information, notice
that if you use another network than 10.0.0.0/8 to summary, for example, if you use the command
ip summary-address eigrp 123 10.2.0.0 255.255.0.0 you will leave a /16 network in the output of
the show ip route command.
24
But in your real exam, if you don't see the line "10.0.0.0/8 is a summary,....Null0" then you can
summary using the network 10.2.0.0/16. This summarization is better because all the pings can
work well.
Finally don't forget to use the copy running-config startup-config command on routers R3 and R4
to save the configurations.
R3(config-if)# end
R3# copy run start
R4(config-if)# end
R4# copy run start
QUESTION 42
Lab Simulation 3 - IPv6 OSPF Virtual Link
25
Answer:
To troubleshoot the problem, first issue the show running-config on all of 4 routers.
Pay more attention to the outputs of routers R2 and R3.
The output of the "show running-config" command of R2:
And
The output of the "show running-config" command of R3:
26
27
28
We knew that all areas in an Open Shortest Path First (OSPF) autonomous system must be
physically connected to the backbone area (Area 0). In some cases, where this is not possible,
we can use a virtual link to connect to the backbone through a non-backbone area. The area
through which you configure the virtual link is known as a transit area. In this case, the area 11
will become the transit area. Therefore, routers R2 and R3 must be configured with the area
<area id> virtual-link <neighbor router-id> command. + Configure virtual link on R2 (from the first
output above, we learned that the OSPF process ID of R2 is 1):
R2> enable
R2(config)# ipv6 router ospf 1
R2(config-rtr)# area 11 virtual-link 3.3.3.3
Save the configuration:
R2(config-rtr)# end
R2# copy running-config startup-config
(Notice that we have to use neighbor router-id 3.3.3.3, not R2's router-id 2.2.2.2) + Configure
virtual link on R3 (from the second output above, we learned that the OSPF process ID of R3 is 1
and we have to disable the wrong configuration of "area 54 virtual-link 4.4.4.4"):
R3> enable
R3(config-rtr)# no area 54 virtual-link 4.4.4.4
R3(config-rtr)# area 11 virtual-link 2.2.2.2
Save the configuration:
R3(config-rtr)# end
R3# copy running-config startup-config
You should check the configuration of R4, too.
R4(config-router)# no area 54 virtual-link 3.3.3.3
R4(config-router)# end
After finishing the configuration don't forget to ping between R1 and R4 to make sure they work
well!
Note: If you want to check the routing information, use the show ipv6 route command ,not "show
ip route".
QUESTION 43
Lab Simulation 4 - Policy Based Routing
You are a network engineer with ROUTE.com, a small IT company. ROUTE.com has two
connections to the Internet; one via a frame relay link and one via an EoMPLS link. IT policy
requires that all outbound HTTP traffic use the frame relay link when it is available. All other traffic
may use either link. No static or default routing is allowed.
Choose and configure the appropriate path selection feature to accomplish this task.
You may use the Test Workstation to generate HTTP traffic to validate your solution.
29
Answer:
(1) First create the access list that catches the HTTP traffic:
R1(config)# access-list 101 permit tcp any any eq www
(2) Configure the route map that sets the next hop address to be ISP1 and permits the rest of the
traffic:
R1(config)# route-map
R1(config-route-map)#
R1(config)# route-map
pbr permit 10
match ip address 101
set ip next-hop 10.1.100.2
exit
pbr permit 20
(3) Apply the route-map on the interface to the server in the EIGRP Network:
R1(config-route-map)# exit
R1(config)# int fa0/1
R1(config-if)# ip policy route-map pbr
R1(config-if)# exit
R1(config)# exit
QUESTION 44
Lab Simulation - EIGRP OSPF Redistribution
You are a network engineer with ROUTE.com, a small IT company. They have recently merged
two organizations and now need to merge their networks as shown in the topology exhibit. One
network is using OSPF as its IGP and the other is using EIGRP as its IGP. R4 has been added to
the existing OSPF network to provide the interconnect between the OSPF and EIGRP networks.
Two links have been added that will provide redundancy.
30
The network requirements state that you must be able to ping and telnet from loopback 101 on
R1 to the OPSF domain test address of 172.16.1.100. All traffic must use the shortest path that
provides the greatest bandwidth. The redundant paths from the OSPF network to the EIGRP
network must be available in case of a link failure. No static or default routing is allowed in either
network.
A previous network engineer has started the merger implementation and has successfully
assigned and verified all IP addressing and basic IGP routing. You have been tasked with
completing the implementation and ensuring that the network requirements are met. You may not
remove or change any of the configuration commands currently on any of the routers. You may
add new commands or change default values.
Answer:
R2# show interface s0/0/0
Write down these 5 parameters, notice that we have to divide the Delay by 10 because the metric
unit is in tens of microsecond.
For example, we get Bandwidth=1544 Kbit, Delay=20000 us, Reliability=255, Load=1, MTU=1500
bytes then we would redistribute as follows:
R2# config terminal
R2(config)# router ospf 1
R2(config-router)# redistribute eigrp 100 metric-type 1 subnets
R2(config-router)# exit
R2(config-router)# router eigrp 100
R2(config-router)# redistribute ospf 1 metric 1544 2000 255 1 1500
Note: In fact, these parameters are just used for reference and we can use other parameters with
no problem.
If the delay is 20000us then we need to divide it by 10, that is 20000 / 10 = 2000)
For R3 we use the show interface fa0/0 to get 5 parameters too
31
R3# show interface fa0/0

For example we get Bandwidth=10000 Kbit, Delay=1000 us, Reliability=255, Load=1, MTU=1500
bytes
R3# config terminal
R3(config)# router ospf 1
R3(config-router)# redistribute eigrp 100 metric-type 1 subnets
R3(config)# exit
R3(config-router)# router eigrp 100
R3(config-router)# redistribute ospf 1 metric 10000 100 255 1 1500
Finally you should try to "show ip route" to see the 172.16.100.1 network (the network behind
R4) in the routing table of R1 and make a ping from R1 to this network.
Note: If the link between R2 and R3 is FastEthernet link, we must put the command below under
EIGRP process to make traffic from R1 to go through R3 (R1 -> R2 -> R3 -> R4), which is better
than R1 -> R2 -> R4.
R2(config-router)# distance eigrp 90 105
This command sets the Administrative Distance of all EIGRP internal routes to 90 and all EIGRP
external routes to 105, which is smaller than the Administrative Distance of OSPF (110) -> the
link between R2 & R3 will be preferred to the serial link between R2 & R4.
Note: The actual OPSF and EIGRP process numbers may change in the actual exam so be sure
to use the actual correct values, but the overall solution is the same.
QUESTION 45
You have been asked to evaluate how EIGRP is functioning in a customer network.
32
Traffic from R1 to R6s Loopback address is load shared between R1-R2-R4-R6 and R1-R3-R5R6 paths. What is the ratio of traffic over each path?
A.
B.
C.
D.
1:1
1:5
6:8
19:80
Answer: D
Explanation:
First, find the IP address of the loopback0 interface on R6:
We see that it is 150.1.6.6, so we issue the "show ip route 150.1.6.6" command from R1 and see
33
this:
Notice the "traffic share count" shows 19 for the first path, and 80 for the second path.
QUESTION 46
34
What type of route filtering is occurring on R6

A.
B.
C.
D.
Distribute-list using an ACL

Distribute-list using a prefix-list
Distribute-list using a route-map
An ACL using a distance of 255
Answer: A
Explanation:
The configuration on R6 is as follows:
This is a standard distribute list using access list number 1.
QUESTION 47
35
Which key chain is being used for authentication of EIGRP adjacency between R4 and R2?
A.
B.
C.
D.
CISCO
EIGRP
key
MD5
Answer: A
Explanation:
R4 and R2 configs are as shown below:
36
Clearly we see the actual key chain is named CISCO.
QUESTION 48
37
What is the advertised distance for the 192.168.46.0 network on R1?

A.
B.
C.
D.
333056
1938688
1810944
307456
Answer: C
Explanation:
R1's routing table is as follows
The numbers after the route specify the administrative distance of the route (90 for EIGRP) and
the distance metric of that particular route, which is shows as 1810944 for the 192.168.46.0 route.
QUESTION 49
38
What percent of R1's interfaces bandwidth is EIGRP allowed to use?

A.
B.
C.
D.
10
20
30
40
Answer: B
Explanation:
The relevant configuration of R1 is shown below:
39
ip bandwidth-percent eigrp 1 20
1 = the EIGRP AS
20 = 20% of the bandwidth
QUESTION 50
Scenario:
You have been asked to evaluate an OSPF network setup in a test lab and to answer questions a
customer has about its operation. The customer has disabled your access to the show runningconfig command.
40
How old is the Type 4 LSA from Router 3 for area 1 on the router R5 based on the output you
have examined?
A.
B.
C.
D.
1858
1601
600
1569
Answer: A
Explanation:
Part of the "show ip ospf topology" command on R5 shows this:
41
The Link ID of R3 (3.3.3.3) shows the age is 1858.
QUESTION 51
Scenario:
Which of the following statements is true about the serial links that terminate in R3
A.
B.
C.
D.
The R1-R3 link needs the neighbor command for the adjacency to stay up
The R2-R3 link OSPF timer values are 30, 120, 120
The R1-R3 link OSPF timer values should be 10,40,40
R3 is responsible for flooding LSUs to all the routers on the network.
Answer: B
Explanation:
We can see the configured timers using the following command:
42
QUESTION 52
Scenario:
43
How many times was SPF algorithm executed on R4 for Area 1?

A.
B.
C.
D.
E.
F.
1
5
9
20
54
224
Answer: C
Explanation:
This can be found using the "show ip ospf" command on R4.
Look for the Area 1 stats which shows this:
QUESTION 53
Scenario:
44
Areas of Router 5 and 6 are not normal areas, inspect their routing tables and determine which
statement is true?
A.
B.
C.
D.
E.
R5's Loopback and R6's Loopback are both present in R5's Routing table
R5's Loopback and R6's Loopback are both present in R6's Routing table
Only R5's loopback is present in R5's Routing table
Answer: A
Explanation:
Here are the routing tables of R5 and R6:
45
46
QUESTION 54
Drag and Drop Question
Answer:
47
QUESTION 55
Answer:
48
QUESTION 56
Refer to the exhibit. Based on this FIB table, which statement is correct?
A.
B.
C.
D.
There is no default gateway.

The IP address of the router on FastEthernet is 209.168.201.1.
The gateway of last resort is 192.168.201.1.
The router will listen for all multicast traffic.
Answer: C
Explanation:
The 0.0.0.0/0 route is the default route and is listed as the first CEF entry. Here we see the next
hop for this default route lists 192.168.201.1 as the default router (gateway of last resort).
QUESTION 57
Refer to the exhibit. A network administrator checks this adjacency table on a router.
What is a possible cause for the incomplete marking?
A.
B.
C.
D.
incomplete ARP information

incorrect ACL
dynamic routing protocol failure
serial link congestion
Answer: A
Explanation:
To display information about the Cisco Express Forwarding adjacency table or the hardware
Layer 3-switching adjacency table, use the show adjacency command.
Reasons for Incomplete Adjacencies
There are two known reasons for an incomplete adjacency:
The router cannot use ARP successfully for the next-hop interface.
After a clear ip arp or a clear adjacency command, the router marks the adjacency as incomplete.
Then it fails to clear the entry.
49
In an MPLS environment, IP CEF should be enabeled for Label Switching. Interface level
command ip route-cache cef
No ARP Entry
When CEF cannot locate a valid adjacency for a destination prefix, it punts the packets to the
CPU for ARP resolution and, in turn, for completion of the adjacency.
http://www.cisco.com/c/en/us/support/docs/ip/express-forwarding-cef/17812-cef-incomp.html#t4
QUESTION 58
A network engineer notices that transmission rates of senders of TCP traffic sharply increase and
decrease simultaneously during periods of congestion. Which condition causes this?
A.
B.
C.
D.
global synchronization
tail drop
random early detection
queue management algorithm
Answer: A
Explanation:
TCP global synchronization in computer networks can happen to TCP/IP flows during periods of
congestion because each sender will reduce their transmission rate at the same time when
packet loss occurs.
Routers on the Internet normally have packet queues, to allow them to hold packets when the
network is busy, rather than discarding them.
Because routers have limited resources, the size of these queues is also limited. The simplest
technique to limit queue size is known as tail drop. The queue is allowed to fill to its maximum
size, and then any new packets are simply discarded, until there is space in the queue again.
This causes problems when used on TCP/IP routers handling multiple TCP streams, especially
when bursty traffic is present. While the network is stable, the queue is constantly full, and there
are no problems except that the full queue results in high latency. However, the introduction of a
sudden burst of traffic may cause large numbers of established, steady streams to lose packets
simultaneously.
http://en.wikipedia.org/wiki/TCP_global_synchronization
QUESTION 59
Which three problems result from application mixing of UDP and TCP streams within a network
with no QoS? (Choose three.)
A.
B.
C.
D.
E.
starvation
jitter
latency
windowing
lower throughput
Answer: ACE
Explanation:
It is a general best practice not to mix TCP-based traffic with UDP-based traffic (especially
streaming video) within a single service provider class due to the behaviors of these protocols
during periods of congestion. Specifically, TCP transmitters will throttle-back flows when drops
have been detected. Although some UDP applications have application-level windowing, flow
control, and retransmission capabilities, most UDP transmitters are completely oblivious to drops
and thus never lower transmission rates due to dropping. When TCP flows are combined with
UDP flows in a single service provider class and the class experiences congestion, then TCP
50
flows will continually lower their rates, potentially giving up their bandwidth to drop-oblivious UDP
flows. This effect is called TCP-starvation/UDP-dominance. This can increase latency and lower
the overall throughput.
TCP-starvation/UDP-dominance likely occurs if (TCP-based) mission-critical data is assigned to
the same service provider class as (UDP-based) streaming video and the class experiences
sustained congestion. Even if WRED is enabled on the service provider class, the same behavior
would be observed, as WRED (for the most part) only affects TCP-based flows.
Granted, it is not always possible to separate TCP-based flows from UDP-based flows, but it is
beneficial to be aware of this behavior when making such application-mixing decisions.
http://www.cisco.com/warp/public/cc/so/neso/vpn/vpnsp/spqsd_wp.htm
QUESTION 60
Which method allows IPv4 and IPv6 to work together without requiring both to be used for a
single connection during the migration process?
A.
B.
C.
D.
dual-stack method
6to4 tunneling
GRE tunneling
NAT-PT
Answer: A
Explanation:
Dual stack means that devices are able to run IPv4 and IPv6 in parallel. It allows hosts to
simultaneously reach IPv4 and IPv6 content, so it offers a very flexible coexistence strategy. For
sessions that support IPv6, IPv6 is used on a dual stack endpoint. If both endpoints support Ipv4
only, then IPv4 is used.
Benefits:
Native dual stack does not require any tunneling mechanisms on internal networks ?Both IPv4
and IPv6 run independent of each other
Dual stack supports gradual migration of endpoints, networks, and applications.
http://www.cisco.com/web/strategy/docs/gov/IPV6at_a_glance_c45-625859.pdf
QUESTION 61
Which statement about the use of tunneling to migrate to IPv6 is true?
A. Tunneling is less secure than dual stack or translation.
B. Tunneling is more difficult to configure than dual stack or translation.
C. Tunneling does not enable users of the new protocol to communicate with users of the old
protocol without dual-stack hosts.
D. Tunneling destinations are manually determined by the IPv4 address in the low-order 32 bits of
IPv4-compatible IPv6 addresses.
Answer: C
Explanation:
Using the tunneling option, organizations build an overlay network that tunnels one protocol over
the other by encapsulating IPv6 packets within IPv4 packets and IPv4 packets within IPv6
packets. The advantage of this approach is that the new protocol can work without disturbing the
old protocol, thus providing connectivity between users of the new protocol. Tunneling has two
disadvantages, as discussed in RFC 6144:
Users of the new architecture cannot use the services of the underlying infrastructure.
Tunneling does not enable users of the new protocol to communicate with users of the old
protocol without dual-stack hosts, which negates interoperability.
http://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/enterprise-ipv6-
51
solution/white_paper_c11-676278.html
QUESTION 62
Refer to the exhibit. Which one statement is true?
A. Traffic from the 172.16.0.0/16 network will be blocked by the ACL.

B. The 10.0.0.0/8 network will not be advertised by Router B because the network statement for the
10.0.0.0/8 network is missing from Router B.
C. The 10.0.0.0/8 network will not be in the routing table on Router B.
D. Users on the 10.0.0.0/8 network can successfully ping users on the 192.168.5.0/24 network, but
users on the 192.168.5.0/24 cannot successfully ping users on the 10.0.0.0/8 network.
E. Router B will not advertise the 10.0.0.0/8 network because it is blocked by the ACL.
Answer: E
Explanation:
You can filter what individual routes are sent (out) or received (in) to any interface within your
EIGRP configuration.
One example is noted above. If you filter outbound, the next neighbor(s) will not know about
anything except the 172.16.0.0/16 route and therefore won't send it to anyone else downstream.
If you filter inbound, YOU won't know about the route and therefore won't send it to anyone else
downstream.
QUESTION 63
Prior to enabling PPPoE in a virtual private dialup network group, which task must be completed?
A.
B.
C.
D.
Disable CDP on the interface.

Execute the vpdn enable command.
Execute the no switchport command.
Enable QoS FIFO for PPPoE support.
Answer: B
52
QUESTION 64
A network engineer is configuring a routed interface to forward broadcasts of UDP 69, 53, and 49
to 172.20.14.225. Which command should be applied to the configuration to allow this?
A.
B.
C.
D.
router(config-if)#ip helper-address 172.20.14.225

router(config-if)#udp helper-address 172.20.14.225
router(config-if)#ip udp helper-address 172.20.14.225
router(config-if)#ip helper-address 172.20.14.225 69 53 49
Answer: A
Explanation:
To let a router forward broadcast packet the command ip helper-address can be used.
The broadcasts will be forwarded to the unicast address which is specified with the ip helper
command.
ip helper-address {ip address}
When configuring the ip helper-address command, the following broadcast packets will be
forwarded by the router by default:
TFTP -- UDP port 69
Domain Name System (DNS) ?UDP port 53
Time service -- port 37
NetBIOS Name Server -- port 137
NetBIOS Datagram Server -- port 138
Bootstrap Protocol (BOOTP) -- port 67
TACACS UDP port 49
http://www.cisco-faq.com/163/forward_udp_broadcas.html
QUESTION 65
What is a function of NPTv6?
A.
B.
C.
D.
It interferes with encryption of the full IP payload.

It maintains a per-node state.
It is checksum-neutral.
It rewrites transport layer headers.
Answer: C
Explanation:
RFC 6296 describes a stateless Ipv6-to-Ipv6 Network Prefix Translation (NPTv6) function,
designed to provide address independence to the edge network. It is transport-agnostic with
respect to transports that do not checksum the IP header, such as SCTP, and to transports that
use the TCP/UDP/DCCP (Datagram Congestion Control Protocol) pseudo-header and checksum
NPTv6 provides a simple and compelling solution to meet the address-independence requirement
in Ipv6. The address-independence benefit stems directly from the translation function of the
network prefix translator. To avoid as many of the issues associated with NAPT44 as possible,
NPTv6 is defined to include a two-way, checksum-neutral, algorithmic translation function, and
nothing else.
http://tools.ietf.org/html/rfc6296
QUESTION 66
IPv6 has just been deployed to all of the hosts within a network, but not to the servers. Which
feature allows IPv6 devices to communicate with IPv4 servers?
A. NAT
53
B.
C.
D.
E.
NATng
NAT64
dual-stack NAT
DNS64
Answer: C
Explanation:
NAT64 is a mechanism to allow Ipv6 hosts to communicate with Ipv4 servers. The NAT64 server
is the endpoint for at least one Ipv4 address and an Ipv6 network segment of 32-bits (for instance
64:ff9b::/96, see RFC 6052, RFC 6146). The Ipv6 client embeds the Ipv4 address it wishes to
communicate with using these bits, and sends its packets to the resulting address. The NAT64
server then creates a NAT-mapping between the Ipv6 and the Ipv4 address, allowing them to
communicate.
http://en.wikipedia.org/wiki/NAT64
QUESTION 67
A network engineer initiates the ip sla responder tcp-connect command in order to gather
statistics for performance gauging. Which type of statistics does the engineer see?
A.
B.
C.
D.
connectionless-oriented
service-oriented
connection-oriented
application-oriented
Answer: C
Explanation:
Configuration Examples for IP SLAs TCP Connect Operations The following example shows how
to configure a TCP Connection-oriented operation from Device B to the Telnet port (TCP port 23)
of IP Host 1 (IP address 10.0.0.1), as shown in the "TCP Connect Operation" figure in the
"Information About the IP SLAs TCP Connect Operation" section. The operation is scheduled to
start immediately. In this example, the control protocol is disabled on the source (Device B). IP
SLAs uses the control protocol to notify the IP SLAs responder to enable the target port
temporarily. This action allows the responder to reply to the TCP Connect operation. In this
example, because the target is not a Cisco device and a well-known TCP port is used, there is no
need to send the control message.
Device A (target device) Configuration
configure terminal
ip sla responder tcp-connect ipaddress 10.0.0.1 port 23
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipsla/configuration/15-mt/sla-15-mtbook/sla_tcp_conn.html
QUESTION 68
A network engineer executes the ipv6 flowset command. What is the result?
A.
B.
C.
D.
Flow-label marking in 1280-byte or larger packets is enabled.

Flow-set marking in 1280-byte or larger packets is enabled.
IPv6 PMTU is enabled on the router.
IPv6 flow control is enabled on the router.
Answer: A
Explanation:
Enabling Flow-Label Marking in Packets that Originate from the Device This feature allows the
54
device to track destinations to which the device has sent packets that are 1280 bytes or larger.
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipv6_basic/configuration/15-mt/ip6b-15-mtbook/ip6-mtu-path-disc.html
QUESTION 69
A network engineer executes the show ip flow export command. Which line in the output indicates
that the send queue is full and export packets are not being sent?
A.
B.
C.
D.
output drops
enqueuing for the RP
fragmentation failures
adjacency issues
Answer: A
Explanation:
http://www.cisco.com/c/en/us/td/docs/ios/12_0s/feature/guide/oaggnf.html
QUESTION 70
A network engineer is asked to configure a "site-to-site" IPsec VPN tunnel. One of the last things
that the engineer does is to configure an access list (access-list 1 permit any) along with the
command ip nat inside source list 1 int s0/0 overload. Which functions do the two commands
serve in this scenario?
A. The command access-list 1 defines interesting traffic that is allowed through the tunnel.
B. The command ip nat inside source list 1 int s0/0 overload disables "many-to-one" access for all
devices on a defined segment to share a single IP address upon exiting the external interface.
C. The command access-list 1 permit any defines only one machine that is allowed through the
tunnel.
D. The command ip nat inside source list 1 int s0/0 overload provides "many-to-one" access for all
devices on a defined segment to share a single IP address upon exiting the external interface.
Answer: D
Explanation:
http://www.cisco.com/en/US/tech/tk648/tk361/technologies_tech_note09186a0080094e77.shtml
QUESTION 71
A network administrator executes the command clear ip route. Which two tables does this
command clear and rebuild? (Choose two.)
A.
B.
C.
D.
E.
F.
IP routing
FIB
ARP cache
MAC address table
Cisco Express Forwarding table
topology table
Answer: AB
QUESTION 72
Which switching method is used when entries are present in the output of the command show ip
55
cache?
A.
B.
C.
D.
fast switching
process switching
Cisco Express Forwarding switching
cut-through packet switching
Answer: A
Explanation:
Fast switching allows higher throughput by switching a packet using a cache created by the initial
packet sent to a particular destination. Destination addresses are stored in the high-speed cache
to expedite forwarding. Routers offer better packet-transfer performance when fast switching is
enabled. Fast switching is enabled by default on all interfaces that support fast switching. To
display the routing table cache used to fast switch IP traffic, use the "show ip cache" EXEC
command.
http://www.cisco.com/c/en/us/td/docs/ios/12_2/switch/command/reference/fswtch_r/xrfscmd5.html
#wp1038133
QUESTION 73
Which two actions must you perform to enable and use window scaling on a router? (Choose
two.)
A.
B.
C.
D.
E.
Execute the command ip tcp window-size 65536.

Set window scaling to be used on the remote host.
Execute the command ip tcp queuemax.
Set TCP options to "enabled" on the remote host.
Execute the command ip tcp adjust-mss.
Answer: AB
Explanation:
The TCP Window Scaling feature adds support for the Window Scaling option in RFC 1323, TCP
Extensions for High Performance. A larger window size is recommended to improve TCP
performance in network paths with large bandwidth-delay product characteristics that are called
Long Fat Networks (LFNs). The TCP Window Scaling enhancement provides that support. The
window scaling extension in Cisco IOS software expands the definition of the TCP window to 32
bits and then uses a scale factor to carry this 32-bit value in the 16-bit window field of the TCP
header. The window size can increase to a scale factor of 14. Typical applications use a scale
factor of 3 when deployed in LFNs.
The TCP Window Scaling feature complies with RFC 1323. The larger scalable window size will
allow TCP to perform better over LFNs. Use the ip tcp window-size command in global
configuration mode to configure the TCP window size. In order for this to work, the remote host
must also support this feature and its window size must be increased.
http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/ipapp/configuration/12-4t/iap-12-4t-book/iaptcp.html#GUID-BD998AC6-F128-47DD-B5F7-B226546D4B08
QUESTION 74
Which PPP authentication method sends authentication information in cleartext?
A.
B.
C.
D.
MS CHAP
CDPCP
CHAP
PAP
56
Answer: D
Explanation:
PAP authentication involves a two-way handshake where the username and password are sent
across the link in clear text; hence, PAP authentication does not provide any protection against
playback and line sniffing.
CHAP authentication, on the other hand, periodically verifies the identity of the remote node using
a three-way handshake. After the PPP link is established, the host sends a "challenge" message
to the remote node. The remote node responds with a value calc"lated usi"g a one-way hash
function. The host checks the response against its own calculation of the expected hash value. If
the values match, the authentication is acknowledged; otherwise, the connection is terminated.
http://www.cisco.com/c/en/us/support/docs/wan/point-to-point-protocol-ppp/10241-ppp-callinhostname.html
QUESTION 75
Which protocol uses dynamic address mapping to request the next-hop protocol address for a
specific connection?
A.
B.
C.
D.
Frame Relay inverse ARP

static DLCI mapping
Frame Relay broadcast queue
dynamic DLCI mapping
Answer: A
Explanation:
Dynamic address mapping uses Frame Relay Inverse ARP to request the next-hop protocol
address for a specific connection, given its known DLCI. Responses to Inverse ARP requests are
entered in an address-to-DLCI mapping table on the router or access server; the table is then
used to supply the next-hop protocol address or the DLCI for outgoing traffic.
http://www.cisco.com/c/en/us/td/docs/ios/12_2/wan/configuration/guide/fwan_c/wcffrely.html
QUESTION 76
What is the default OSPF hello interval on a Frame Relay point-to-point network?
A.
B.
C.
D.
10
20
30
40
Answer: A
Explanation:
Before you troubleshoot any OSPF neighbor-related issues on an NBMA network, it is important
to remember that an NBMA network can be configured in these modes of operation with the ip
ospf network command:
The Hello and Dead Intervals of each mode are described in this table:
Network Type
Hello Interval (secs)
Dead Interval (secs)
Point-to-Point
Point-to-Multipoint
Broadcast
Non-Broadcast
57
http://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/13693-22.html
QUESTION 77
A router with an interface that is configured with ipv6 address autoconfig also has a link- local
address assigned. Which message is required to obtain a global unicast address when a router is
present?
A.
B.
C.
D.
DHCPv6 request
router-advertisement
neighbor-solicitation
redirect
Answer: B
Explanation:
Autoconfiguration is performed on multicast-enabled links only and begins when a multicastenabled interface is enabled (during system startup or manually). Nodes (both, hosts and routers)
begin the process by generating a link-local address for the interface. It is formed by appending
the interface identifier to well-known link-local prefix FE80::0. The interface identifier replaces the
right-most zeroes of the link-local prefix.Before the link-local address can be assigned to the
interface, the node performs the Duplicate Address Detection mechanism to see if any other node
is using the same link-local address on the link. It does this by sending a Neighbor Solicitation
message with target address as the "tentative" address and destination address as the solicitednode multicast address corresponding to this tentative address. If a node responds with a
Neighbor Advertisement message with tentative address as the target address, the address is a
duplicate address and must not be used. Hence, manual configuration is required. Once the node
verifies that its tentative address is unique on the link, it assigns that link-local address to the
interface. At this stage, it has IP-connectivity to other neighbors on this link. The autoconfiguration
on the routers stop at this stage, further tasks are performed only by the hosts. The routers will
need manual configuration (or stateful configuration) to receive site-local or global addresses.
The next phase involves obtaining Router Advertisements from routers if any routers are present
on the link. If no routers are present, a stateful configuration is required. If routers are present, the
Router Advertisements notify what sort of configurations the hosts need to do and the hosts
receive a global unicast IPv6 address.
https://sites.google.com/site/amitsciscozone/home/important-tips/ipv6/ipv6-statelessautoconfiguration
QUESTION 78
An engineer has configured a router to use EUI-64, and was asked to document the IPv6 address
of the router. The router has the following interface parameters:
mac address C601.420F.0007
subnet 2001:DB8:0:1::/64
Which IPv6 addresses should the engineer add to the documentation?
A.
B.
C.
D.
2001:DB8:0:1:C601:42FF:FE0F:7
2001:DB8:0:1:FFFF:C601:420F:7
2001:DB8:0:1:FE80:C601:420F:7
2001:DB8:0:1:C601:42FE:800F:7
Answer: A
Explanation:
58
Extended Unique Identifier (EUI), as per RFC2373, allows a host to assign iteslf a unique 64-Bit
IP Version 6 interface identifier (EUI-64). This feature is a key benefit over IPv4 as it eliminates
the need of manual configuration or DHCP as in the world of IPv4. The IPv6 EUI-64 format
address is obtained through the 48-bit MAC address. The Mac address is first separated into two
24-bits, with one being OUI (Organizationally Unique Identifier) and the other being NIC specific.
The 16-bit 0xFFFE is then inserted between these two 24-bits to for the 64-bit EUI address. IEEE
has chosen FFFE as a reserved value which can only appear in EUI-64 generated from the EUI48 MAC address.
QUESTION 79
For security purposes, an IPv6 traffic filter was configured under various interfaces on the local
router. However, shortly after implementing the traffic filter, OSPFv3 neighbor adjacencies were
lost. What caused this issue?
A. The traffic filter is blocking all ICMPv6 traffic.
B. The global anycast address must be added to the traffic filter to allow OSPFv3 to work properly.
C. The link-local addresses that were used by OSPFv3 were explicitly denied, which caused the
neighbor relationships to fail.
D. IPv6 traffic filtering can be implemented only on SVIs.
Answer: C
Explanation:
OSPFv3 uses link-local Ipv6 addresses for neighbor discovery and other features, so if any Ipv6
traffic filters are implemented be sure to include the link local address so that it is permitted in the
filter list.
http://www.cisco.com/c/en/us/td/docs/switches/datacenter/sw/5_x/nxos/unicast/configuration/guide/l3_cli_nxos/l3_ospfv3.html
QUESTION 80
What is the purpose of the autonomous-system {autonomous-system-number} command?
A.
B.
C.
D.
It sets the EIGRP autonomous system number in a VRF.

It sets the BGP autonomous system number in a VRF.
It sets the global EIGRP autonomous system number.
It sets the global BGP autonomous system number.
Answer: A
Explanation:
To configure the autonomous-system number for an Enhanced Interior Gateway Routing Protocol
(EIGRP) routing process to run within a VPN routing and forwarding (VRF) instance, use the
autonomous-system command in address-family configuration mode. To remove the
autonomous-system for an EIGRP routing process from within a VPN VRF instance, use the no
form of this command.
Autonomous-system autonomous-system-number
no autonomous-system autonomous-system-number
http://www.cisco.com/c/en/us/td/docs/ios/iproute_eigrp/command/reference/ire_book/ire_a1.html#
wp1062796
QUESTION 81
A company has just opened two remote branch offices that need to be connected to the corporate
network. Which interface configuration output can be applied to the corporate router to allow
communication to the remote sites?
59
A. interface Tunnel0
bandwidth 1536
ip address 209.165.200.230 255.255.255.224
tunnel source Serial0/0
tunnel mode gre multipoint
B. interface fa0/0
bandwidth 1536
ip address 209.165.200.230 255.255.255.224
C. interface Tunnel0
bandwidth 1536
ip address 209.165.200.231 255.255.255.224
tunnel source 209.165.201.1
tunnel-mode dynamic
D. interface fa 0/0
bandwidth 1536
ip address 209.165.200.231 255.255.255.224
tunnel source 192.168.161.2
tunnel destination 209.165.201.1
tunnel-mode dynamic
Answer: A
Explanation:
The configuration of mGRE allows a tunnel to have multiple destinations. The configuration of
mGRE on one side of a tunnel does not have any relation to the tunnel properties that might exist
at the exit points. This means that an mGRE tunnel on the hub may connect to a p2p tunnel on
the branch. Conversely, a p2p GRE tunnel may connect to an mGRE tunnel. The distinguishing
feature between an mGRE interface and a p2p GRE interface is the tunnel destination. An mGRE
interface does not have a configured destination. Instead the GRE tunnel is configured with the
command tunnel mode gre multipoint. This command is used instead of the tunnel destination
x.x.x.x found with p2p GRE tunnels. Besides allowing for multiple destinations, an mGRE tunnel
requires NHRP to resolve the tunnel endpoints. Note, tunnel interfaces by default are point-topoint (p-p) using GRE encapsulation, effectively they have the tunnel mode gre command, which
is not seen in the configuration because it is the default.
The mGRE configuration is as follows:
!
interface Tunnel0
bandwidth 1536
ip address 10.62.1.10 255.255.255.0
tunnel source Serial0/0
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/WAN_and_MAN/DMVPDG/DMVPN_2
_ Phase2.html
QUESTION 82
A network engineer executes the show crypto ipsec sa command. Which three pieces of
information are displayed in the output? (Choose three.)
A.
B.
C.
D.
inbound crypto map

remaining key lifetime
path MTU
tagged packets
60
E. untagged packets
F. invalid identity packets
Answer: ABC
Explanation:
show crypto ipsec sa
This command shows IPsec SAs built between peers. The encrypted tunnel is built between
12.1.1.1 and 12.1.1.2 for traffic that goes between networks 20.1.1.0 and 10.1.1.0. You can see
the two Encapsulating Security Payload (ESP) SAs built inbound and outbound. Authentication
Header (AH) is not used since there are no AH SAs.
This output shows an example of the show crypto ipsec sa command (bolded ones found in
answers for this question).
interface: FastEthernet0
Crypto map tag: test, local addr. 12.1.1.1
local ident (addr/mask/prot/port): (20.1.1.0/255.255.255.0/0/0) remote ident (addr/mask/prot/port):
(10.1.1.0/255.255.255.0/0/0) current_peer: 12.1.1.2
PERMIT, flags={origin_is_acl,}
#pkts encaps: 7767918, #pkts encrypt: 7767918, #pkts digest 7767918 #pkts decaps: 7760382,
#pkts decrypt: 7760382, #pkts verify 7760382 #pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0,
#pkts decompress failed: 0, #send errors 1, #Recv errors 0 local crypto endpt.: 12.1.1.1, remote
crypto endpt.: 12.1.1.2 path mtu 1500, media mtu 1500
current outbound spi: 3D3
inbound esp sas:
spi: 0x136A010F(325714191)
transform: esp-3des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 3442, flow_id: 1443, crypto map: test sa timing: remaining key lifetime (k/sec):
(4608000/52) IV size: 8 bytes
replay detection support: Y
inbound ah sas:
inbound pcp sas:
inbound pcp sas:
outbound esp sas:
spi: 0x3D3(979)
transform: esp-3des esp-md5-hmac ,
in use settings ={Tunnel, }
slot: 0, conn id: 3443, flow_id: 1444, crypto map: test sa timing: remaining key lifetime (k/sec):
(4608000/52) IV size: 8 bytes
replay detection support: Y
outbound ah sas:
outbound pcp sas:
http://www.cisco.com/c/en/us/support/docs/security-vpn/ipsec-negotiation-ike-protocols/5409ipsec-debug-00.html
QUESTION 83
Refer to the following output:
Router#show ip nhrp detail
10.1.1.2/8 via 10.2.1.2, Tunnel1 created 00:00:12, expire 01:59:47
TypE. dynamic, Flags: authoritative unique nat registered used
NBMA address: 10.12.1.2
What does the authoritative flag mean in regards to the NHRP information?
61
A.
B.
C.
D.
E.
It was obtained directly from the next-hop server.

Data packets are process switches for this mapping entry.
NHRP mapping is for networks that are local to this router.
The mapping entry was created in response to an NHRP registration request.
The NHRP mapping entry cannot be overwritten.
Answer: A
Explanation:
http://www.cisco.com/c/en/us/td/docs/ios/12_4/ip_addr/configuration/guide/hadnhrp.html
QUESTION 84
Which common issue causes intermittent DMVPN tunnel flaps?
A.
B.
C.
D.
a routing neighbor reachability issue

a suboptimal routing table
interface bandwidth congestion
that the GRE tunnel to hub router is not encrypted
Answer: A
Explanation:
DMVPN Tunnel Flaps Intermittently
Problem
DMVPN tunnel flaps intermittently.
Solution
When DMVPN tunnels flap, check the neighborship between the routers as issues with
neighborship formation between routers may cause the DMVPN tunnel to flap. In order to resolve
this problem, make sure the neighborship between the routers is always up.
http://www.cisco.com/c/en/us/support/docs/security-vpn/ipsec-negotiation-ike-protocols/29240dcmvpn.html#Prblm1
QUESTION 85
Answer:
62
QUESTION 86
Answer:
QUESTION 87
Answer:
63
QUESTION 88
Answer:
QUESTION 89
64
Answer:
QUESTION 90
Place the BGP commands to the proper locations
Answer:
65
QUESTION 91
Answer:
66
QUESTION 92
Answer:
QUESTION 93
What is the purpose of configuring the router as a PPPoE client? Select the best response.
A. to provide VPN access over L2TP
B. to enable PPP session from the router to the termination device at the headend for metro Ethernet
connectivity
C. for DSL connectivity and removing the need for the end-user PC to run the PPPoE client software
D. for connecting the router to a cable modem, which bridges the Ethernet frames from the router to
the cable modem termination system
Answer: C
QUESTION 94
Which three are characteristics of IPv6? (Choose three.) Select 3 response(s).
A.
B.
C.
D.
E.
An IPv6 address is 128 bits long.

An IPv6 header is 20 bits long.
An IPv6 header contains the next header field.
An IPv6 header contains the protocol field.
IPv6 routers send RA messages.
67
F. An IPv6 header contains the header checksum field.

Answer: ACE
QUESTION 95
When an IPv6 enabled host boots, it sends a router solicitation (RS) message. An IPv6 router
responds with a router advertisement (RA). Which two items are contained in the RA? (Choose
two.) Select 2 response(s).
A.
B.
C.
D.
E.
F.
IPv6 address for the host

lifetime of the prefix
prefixes for the link
keepalive timers
request for the local host IP address
any route advertisements it has received
Answer: BC
QUESTION 96
Which statement is true about IPv6? Select the best response.
A.
B.
C.
D.
Only one IPv6 address is assigned per node.

Only one IPv6 address can be assigned to each interface.
Each host can autoconfigure its address without the aid of a DHCP server.
IPv6 hosts use anycast addresses to assign IP addresses to interfaces.
Answer: C
QUESTION 97
What is the IPv6 address FF02::2 used for? Select the best response.
A.
B.
C.
D.
all hosts in a local segment

all routers in a local segment
all hosts in a particular multicast group
all routers in an autonomous system
Answer: B
QUESTION 98
What does the command clear ipv6 ospf process accomplish? Select the best response.
A.
B.
C.
D.
The OSPF adjacencies are cleared and initiated again.

The route table is cleared. Then the OSPF neighbors are reformed.
The shortest path first (SPF) algorithm is performed on the LSA database.
The OSPF database is repopulated. Then the shortest path first (SPF) algorithm is performed.
Answer: D
68
QUESTION 99
When implementing OSPFv3, which statement describes the configuration of OSPF areas?
Select the best response.
A. In interface configuration mode, the OSPFv3 area ID combination assigns interfaces to OSPFv3
areas.
B. In router configuration mode, the network wildcard area ID combination assigns networks to OSPFv3
areas.
C. In interface configuration mode, the IPv6 OSPF process area ID combination assigns interfaces to
OSPFv3 areas.
D. In router configuration mode, the IPv6 OSPF interface area ID combination assigns interfaces to
OSPFv3 areas.
Answer: C
QUESTION 100
The following exhibit shows ipv6 route output. What would the metric be for a summary route that
summarizes all three OSPFv3 routes displayed?
A.
B.
C.
D.
160
140
120
100
Answer: D
QUESTION 101
How is authentication handled with OSPFv3? Select the best response.
A.
B.
C.
D.
OSPFv3 for IPv6 authentication is supported by SHA-1 authentication.

OSPFv3 for IPv6 authentication is supported by MD5 authentication.
OSPFv3 for IPv6 authentication is supported by IPv6 IPsec.
OSPFv3 for IPv6 authentication is supported by IPv4 IPsec.
69
Answer: C
QUESTION 102
Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional
configuration statement should be included on router R4 to advertise a default route to its
neighbors?

A.
B.
C.
D.
R4(config)# ip default-network 10.0.0.0

R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
R4(config)# ip route 10.0.0.0 255.0.0.0 10.1.1.1
R4(config-router)# default-information originate
Answer: A
QUESTION 103
You have implemented mutual route redistribution between OSPF and EIGRP on a border router.
When checking the routing table on one of the OSPF routers within the OSPF routing domain,
you are seeing some, but not all of the expected routes. Which two things should you verify to
troubleshoot this problem? (Choose two.) Select 2 response(s).
A.
B.
C.
D.
E.
The border router is using a proper seed metric for OSPF.

The border router is using a proper seed metric for EIGRP.
The administrative distance is set for OSPF and EIGRP.
The missing EIGRP routes are present in the routing table of the border router.
The subnet keyword on the border router in the redistribute EIGRP command.
Answer: DE
QUESTION 104
Refer to the exhibit. EIGRP is configured on all routers in the network. On a basis of the show ip
eigrp topology output provided, what conclusion can be derived? Select the best response.
70
A. Router R1 can send traffic destined for network 10.6.1.0/24 out of interface FastEthernet0/0.
B. Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out before it
declares the neighbor unreachable.
C. Router R1 is waiting for a reply from the neighbor 10.1.2.1 to the hello message sent out inquiring
for a second successor to network 10.6.1.0/24.
D. Router R1 is waiting for a reply from the neighbor 10.1.2.1 in response to the query sent out about
network 10.6.1.0/24.
Answer: D
QUESTION 105
Using the rules for IPv6 addressing, how can the address
2031:0000:240F:0000:0000:09C0:123A:121B be rewritten? Select the best response.
A.
B.
C.
D.
2031:0:240F::09C0:123A:121B
2031::240F::09C0:123A:121B
2031::240F:9C0::123A:121B
2031::240F:::09C0:123A:121B
Answer: A
QUESTION 106
What is the difference between the IPv6 addresses ::/0 and ::/128? Select the best response.
A.
B.
C.
D.
E.
F.
::/0 is the unspecified address, and ::/128 is the multicast address.

::/0 is the unicast address, and ::/128 is the anycast address.
::/0 is the unicast address, and ::/128 is the multicast address.
::/0 is the anycast address, and ::/128 is the multicast address.
::/0 is the default route, and ::/128 is the unspecified address.
::/0 is the anycast address, and ::/128 is the default address.
Answer: E
QUESTION 107
Which three restrictions apply to OSPF stub areas? (Choose three.) Select 3 response(s).
A. No virtual links are allowed.
B. The area cannot be a backbone area.
C. Redistribution is not allowed unless the packet is changed to a type 7 packet.
71
D. The area has no more than 10 routers.

E. No autonomous system border routers are allowed.
F. Interarea routes are suppressed.
Answer: ABE
QUESTION 108
Refer to the exhibit. Which three statements accurately describe the result of applying the
exhibited route map? Select 3 response(s).
A. The map prohibits the redistribution of all type 2 external OSPF routes with tag 6 set.
B. The map prohibits the redistribution of all type 2 external OSPF routes.
C. The map redistributes into EIGRP all routes that match the pfx prefix list and the five metric values
40000, 1000, 255, 1, and 1500.
D. The map prohibits the redistribution of all external OSPF routes with tag 6 set.
E. All routes that do no match clauses 10 and 20 of the route map are redistributed with their tags set
to 8.
F. The map permits the redistribution of all type 1 external OSPF routes.
Answer: AEF
QUESTION 109
Which two statements are true about 6to4 tunnels? (Choose two.)
A. In a 6to4 tunnel, the first two bytes of the IPv6 address will be 0?002 and the next four bytes will
be the hexadecimal equivalent of the IPv4 address.
B. In a 6to4 tunnel, the first two bytes of the IPv6 address will be locally derived and the next two bytes
will be the hexadecimal equivalent of the IPv4 address.
C. In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the 2002:c0a8:6301::/48
IPv6 address.
72
D. In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the 2002:c0a8:6301::/16
IPv6 address.
E. In a 6to4 tunnel, the IPv4 address 192.168.99.1 would be converted to the 2002:1315:4463:1::/64
IPv6 address.
Answer: AC
QUESTION 110
Which IPv4-mapped IPv6 address is equivalent to IPv6 address ::ffff:AC11:AC11? Select the best
response.
A.
B.
C.
D.
E.
F.
::ffff:10.12.10.12
::ffff:10.14.10.14
::ffff44.49.44.49
::ffff161.193.161.193
::ffff 172.17.172.17
::ffff193.11.193.11
Answer: E
QUESTION 111
The Dev-1 and Dev-3 routers are OSPF neighbors over the Ethernet 0/0 connection. Based on
the show ip ospf neighbor output from the Dev-1 and Dev-3 routers, which statement is true?
A.
B.
C.
D.
E.
Dev-1 is the DR because it has a higher OSPF router priority.

Dev-1 is the DR because it has a lower OSPF router ID.
Dev-3 is the DR because it has a higher OSPF router priority.
Dev-3 is the DR because it has a lower OSPF router ID.
Both Dev-1 and Dev-3 are using the default OSPF router priority.
Answer: A
QUESTION 112
During a recent OSPF election among three routers, RTA was elected the DR and RTB was
elected the BDR, as seen in the graphic. Assume that RTA fails, and that RTB takes the place of
the DR while RTC becomes the new BDR. What will happen when RTA comes back online?
73

A.
B.
C.
D.
RTA will take the place of DR immediately upon establishing its adjacencies.
RTA will take the place of DR only if RTB fails.
RTA will take the place of DR only if both RTB and RTC fail.
A new election will take place establishing an all new DR and BDR based on configured priority
levels and MAC addresses.
Answer: C
QUESTION 113
By default, which statement is correct regarding the redistribution of routes from other routing
protocols into OSPF? Select the best response.
A.
B.
C.
D.
E.
They will appear in the OSPF routing table as type E1 routes.

They will appear in the OSPF routing table as type E2 routes.
Summarized routes are not accepted.
All imported routes will be automatically summarized when possible.
Only routes with lower administrative distances will be imported.
Answer: B
Explanation:
Type E1 external routes calculate the cost by adding the external cost to the internal cost of each
link that the packet crosses while the external cost of E2 packet routes is always the external cost
only. E2 is useful if you do not want internal routing to determine the path. E1 is useful when
internal routing should be included in path selection. E2 is the default external metric when
redistributing routes from other routing protocols into OSPF.
74
QUESTION 114
What are three key concepts that apply when configuring the EIGRP stub routing feature in a hub
and spoke network? (Choose three.)
A.
B.
C.
D.
E.
F.
A hub router prevents routes from being advertised to the remote router.
Only remote routers are configured as stubs.
Stub routers are not queried for routes.
Spoke routers connected to hub routers answer the route queries for the stub router.
A stub router should have only EIGRP hub routers as neighbors.
EIGRP stub routing should be used on hub routers only.
Answer: BCE
QUESTION 115
An administrator types in the command router ospf 1 and receives the error message:
"OSPF process 1 cannot start." (Output is omitted.)
What should be done to correctly set up OSPF? Select the best response.
A.
B.
C.
D.
Ensure that an interface has been configured with an IP address.

Ensure that an interface has been configured with an IP address and is up.
Ensure that IP classless is enabled.
Ensure that the interfaces can ping their directly connected neighbors.
Answer: B
QUESTION 116
Which three benefits does the Cisco Easy Virtual Network provide to an enterprise network?
(Choose three.)
A.
B.
C.
D.
E.
F.
simplified Layer 3 network virtualization

improved shared services support
enhanced management, troubleshooting, and usability
reduced configuration and deployment time for dot1q trunking
increased network performance and throughput
decreased BGP neighbor configurations
Answer: ABC
QUESTION 117
The enterprise network WAN link has been receiving several denial of service attacks from both
IPv4 and IPv6 sources. Which three elements can you use to identify an IPv6 packet via its
header, in order to filter future attacks? (Choose three.)
A.
B.
C.
D.
E.
Traffic Class
Source address
Flow Label
Hop Limit
Destination Address
75
F. Fragment Offset
Answer: ACD
QUESTION 118
Which traffic characteristic is the reason that UDP traffic that carries voice and video is assigned
to the queue only on a link that is at least 768 kbps?
A.
B.
C.
D.
typically is not fragmented

typically is fragmented
causes windowing
causes excessive delays for video traffic
Answer: A
QUESTION 119
Refer to the exhibit. Which statement about the configuration is true?
A.
B.
C.
D.
20 packets are being sent every 30 seconds.

The monitor starts at 12:05:00 a.m.
Jitter is being tested with TCP packets to port 65051.
The packets that are being sent use DSCP EF.
Answer: A
QUESTION 120
Refer to the exhibit. Which statement about the command output is true?
76
A.
B.
C.
D.
The router exports flow information to 10.10.10.1 on UDP port 5127.

The router receives flow information from 10.10.10.2 on UDP port 5127.
The router exports flow information to 10.10.10.1 on TCP port 5127.
The router receives flow information from 10.10.10.2 on TCP port 5127.
Answer: A
QUESTION 121
Which type of BGP AS number is 64591?
A.
B.
C.
D.
a private AS number
a public AS number
a private 4-byte AS number
a public 4-byte AS number
Answer: A
QUESTION 122
Refer to the exhibit. When summarizing these routes, which route is the summarized route?
77
A.
B.
C.
D.
OI 2001:DB8::/48 [110/100] via FE80::A8BB:CCFF:FE00:6F00, Ethernet0/0

Answer: A
QUESTION 123
Which Cisco VPN technology uses AAA to implement group policies and authorization and is also
used for the XAUTH authentication method?
A.
B.
C.
D.
DMVPN
Cisco Easy VPN
GETVPN
GREVPN
Answer: B
QUESTION 124
Which statement about dual stack is true?
A.
B.
C.
D.
Dual stack translates IPv6 addresses to IPv4 addresses.

Dual stack means that devices are able to run IPv4 and IPv6 in parallel.
Dual stack translates IPv4 addresses to IPv6 addresses.
Dual stack changes the IP addresses on hosts from IPv4 to IPv6 automatically.
Answer: B
QUESTION 125
Refer to the exhibit. The command is executed while configuring a point-to-multipoint Frame
Relay interface. Which type of IPv6 address is portrayed in the exhibit?
A.
B.
C.
D.
link-local
site-local
global
multicast
Answer: A
78
QUESTION 126
Which statement about the NPTv6 protocol is true?
A.
B.
C.
D.
It is used to translate IPv4 prefixes to IPv6 prefixes.

It is used to translate an IPv6 address prefix to another IPv6 prefix.
It is used to translate IPv6 prefixes to IPv4 subnets with appropriate masks.
It is used to translate IPv4 addresses to IPv6 link-local addresses.
Answer: B
QUESTION 127
Which parameter in an SNMPv3 configuration offers authentication and encryption?
A.
B.
C.
D.
auth
noauth
priv
secret
Answer: C
QUESTION 128
How does an IOS router process a packet that should be switched by Cisco Express Forwarding
without an FIB entry?
A.
B.
C.
D.
by forwarding the packet

by dropping the packet
by creating a new FIB entry for the packet
by looking in the routing table for an alternate FIB entry
Answer: B
QUESTION 129
A network administrator is troubleshooting a DMVPN setup between the hub and the spoke.
Which action should the administrator take before troubleshooting the IPsec configuration?
A.
B.
C.
D.
Verify the GRE tunnels.

Verify ISAKMP.
Verify NHRP.
Verify crypto maps.
Answer: A
QUESTION 130
Which IPv6 address type is seen as the next-hop address in the output of the show ipv6 rip
RIPng database command?
A. link-local
79
B.
C.
D.
E.
global
site-local
anycast
multicast
Answer: A
QUESTION 131
Refer to the exhibit. The network setup is running the RIP routing protocol.
Which two events will occur following link failure between R2 and R3? (Choose two.)
A.
B.
C.
D.
R2 will advertise network 192.168.2.0/27 with a hop count of 16 to R1.

R2 will not send any advertisements and will remove route 192.168.2.0/27 from its routing table.
R1 will reply to R2 with the advertisement for network 192.168.2.0/27 with a hop count of 16.
After communication fails and after the hold-down timer expires, R1 will remove the
192.168.2.0/27 route from its routing table.
E. R3 will not accept any further updates from R2, due to the split-horizon loop prevention
mechanism.
Answer: AC
QUESTION 132
A network engineer is trying to modify an existing active NAT configuration on an IOS router by
using the following command:
(config)# no ip nat pool dynamic-nat-pool 192.1.1.20 192.1.1.254
netmask 255.255.255.0
Upon entering the command on the IOS router, the following message is
seen on the console:
%Dynamic Mapping in Use, Cannot remove message or the %Pool outpool in
use, cannot destroy
What is the least impactful method that the engineer can use to modify the existing IP NAT
configuration?
A. Clear the IP NAT translations using the clear ip nat traffic * " command, then replace the NAT
configuration quickly, before any new NAT entries are populated into the translation table due to
active NAT traffic.
B. Clear the IP NAT translations using the clear ip nat translation * " command, then replace the
NAT configuration quickly, before any new NAT entries are populated into the translation table
due to active NAT traffic.
80
C. Clear the IP NAT translations using the reload command on the router, then replace the NAT
active NAT traffic.
D. Clear the IP NAT translations using the clear ip nat table * " command, then replace the NAT
active NAT traffic.
Answer: B
QUESTION 133
To configure SNMPv3 implementation, a network engineer is using the AuthNoPriv security level.
What effect does this action have on the SNMP messages?
A.
B.
C.
D.
They become unauthenticated and unencrypted.

They become authenticated and unencrypted.
They become authenticated and encrypted.
They become unauthenticated and encrypted.
Answer: B
QUESTION 134
Which three items can you track when you use two time stamps with IP SLAs? (Choose three.)
A.
B.
C.
D.
E.
F.
delay
jitter
packet loss
load
throughput
path
Answer: ABC
QUESTION 135
An engineer executes the ip flow ingress command in interface configuration mode. What is the
result of this action?
A.
B.
C.
D.
It enables the collection of IP flow samples arriving to the interface.

It enables the collection of IP flow samples leaving the interface.
It enables IP flow while disabling IP CEF on the interface.
It enables IP flow collection on the physical interface and its subinterfaces.
Answer: A
QUESTION 136
Two aspects of an IP SLA operation can be tracked: state and reachability. Which statement
about state tracking is true?
A. When tracking state, an OK return code means that the track's state is up; any other return code
means that the track's state is down.
81
B. When tracking state, an OK or over threshold return code means that the track's state is up; any
other return code means that the track's state is down.
C. When tracking state, an OK return code means that the track's state is down; any other return
code means that the track's state is up.
D. When tracking state, an OK or over threshold return code means that the track's state is down;
any other return code means that the track's state is up.
Answer: A
QUESTION 137
A network engineer has set up VRF-Lite on two routers where all the interfaces are in the same
VRF. At a later time, a new loopback is added to Router 1, but it cannot ping any of the existing
interfaces. Which two configurations enable the local or remote router to ping the loopback from
any existing interface? (Choose two.)
A.
B.
C.
D.
E.
F.
adding a static route for the VRF that points to the global route table
adding the loopback to the VRF
adding dynamic routing between the two routers and advertising the loopback
adding the IP address of the loopback to the export route targets for the VRF
adding a static route for the VRF that points to the loopback interface
adding all interfaces to the global and VRF routing tables
Answer: AB
QUESTION 138
Refer to the exhibit. After configuring GRE between two routers running OSPF that are connected
to each other via a WAN link, a network engineer notices that the two routers cannot establish the
GRE tunnel to begin the exchange of routing updates. What is the reason for this?
A. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number
47.
B. Either a firewall between the two routers or an ACL on the router is blocking UDP 57.
C. Either a firewall between the two routers or an ACL on the router is blocking TCP 47.
D. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number
57.
Answer: A
82
QUESTION 139
The following configuration is applied to a router at a branch site:
ipv6 dhcp pool dhcp-pool
dns-server 2001:DB8:1:B::1
dns-server 2001:DB8:3:307C::42
domain-name example.com
!
If IPv6 is configured with default settings on all interfaces on the router, which two dynamic IPv6
addressing mechanisms could you use on end hosts to provide end-to-end connectivity? (Choose
two.)
A.
B.
C.
D.
EUI-64
SLAAC
DHCPv6
BOOTP
Answer: AB
QUESTION 140
Which PPP authentication method sends authentication information in cleartext?
A.
B.
C.
D.
MS CHAP
CDPCP
CHAP
PAP
Answer: D
QUESTION 141
What is the primary service that is provided when you implement Cisco Easy Virtual Network?
A.
B.
C.
D.
It requires and enhances the use of VRF-Lite.

It reduces the need for common services separation.
It allows for traffic separation and improved network efficiency.
It introduces multi-VRF and label-prone network segmentation.
Answer: C
QUESTION 142
Refer to the following configuration command.
router (config-line)# ntp master 10
Which statement about this command is true?
A. The router acts as an authoritative NTP clock and allows only 10 NTP client connections.
B. The router acts as an authoritative NTP clock at stratum 10.
C. The router acts as an authoritative NTP clock with a priority number of 10.
83
D. The router acts as an authoritative NTP clock for 10 minutes only.

Answer: B
QUESTION 143
Which Cisco VPN technology can use multipoint tunnel, resulting in a single GRE tunnel interface
on the hub, to support multiple connections from multiple spoke devices?
A.
B.
C.
D.
DMVPN
GETVPN
Cisco Easy VPN
FlexVPN
Answer: A
QUESTION 144
A router receives a routing advertisement for the same prefix and subnet from four different
routing protocols. Which advertisement is installed in the routing table?
A.
B.
C.
D.
RIP
OSPF
iBGP
EIGRP
Answer: D
QUESTION 145
Refer to the exhibit. Which statement is true?
A. Traffic from the 172.16.0.0/16 network will be blocked by the ACL.

B. The 10.0.0.0/8 network will not be advertised by Router B because the network statement for the
10.0.0.0/8 network is missing from RouterB.
84
C. The 10.0.0.0/8 network will not be in the routing table on RouterB.

D. Users on the 10.0.0.0/8 network can successfully ping users on the 192.168.5.0/24 network, but
users on the 192.168.5.0/24 cannot successfully ping users on the 10.0.0.0/8 network.
E. Router B will not advertise the 10.0.0.0/8 network because it is blocked by the ACL.
Answer: E
QUESTION 146
Which technology was originally developed for routers to handle fragmentation in the path
between end points?
A.
B.
C.
D.
E.
PMTUD
MSS
windowing
TCP
global synchronization
Answer: A
QUESTION 147
A network engineer is investigating the cause of a service disruption on a network segment and
executes the debug condition interface fastethernet f0/0 command. In which situation is the
debugging output generated?
A.
B.
C.
D.
when packets on the interface are received and the interface is operational
when packets on the interface are received and logging buffered is enabled
when packets on the interface are received and forwarded to a configured syslog server
when packets on the interface are received and the interface is shut down
Answer: A
QUESTION 148
Which two commands would be used to troubleshoot high memory usage for a process? (Choose
two.)
A.
B.
C.
D.
E.
router#show memory allocating-process table

router#show memory summary
router#show memory dead
router#show memory events
router#show memory processor statistics
Answer: AB
QUESTION 149
Refer to the exhibit. The DHCP client is unable to receive a DHCP address from the DHCP
server. Consider the following output:
hostname RouterB
!
85
interface fastethernet 0/0

ip address 172.31.1.1 255.255.255.0
interface serial 0/0
ip address 10.1.1.1 255.255.255.252
!
ip route 172.16.1.0 255.255.255.0 10.1.1.2
Which configuration is required on the Router B fastethernet 0/0 port in order to allow the DHCP
client to successfully receive an IP address from the DHCP server?
A.
B.
C.
D.
RouterB(config-if)# ip helper-address 172.16.1.2

Answer: A
QUESTION 150
If the total bandwidth is 64 kbps and the RTT is 3 seconds, what is the bandwidth delay product?
A.
B.
C.
D.
E.
8,000 bytes
16,000 bytes
24,000 bytes
32,000 bytes
62,000 bytes
Answer: C
QUESTION 151
What are the default timers for RIPng?
A.
B.
C.
D.
Update: 30 seconds Expire: 180 seconds Flush: 240 seconds

86
Answer: A
QUESTION 152
What is the purpose of the route-target command?
A.
B.
C.
D.
It extends the IP address to identify which VRF instance it belongs to.

It enables multicast distribution for VRF-Lite setups to enhance IGP routing protocol capabilities.
It manages the import and export of routes between two or more VRF instances.
It enables multicast distribution for VRF-Lite setups to enhance EGP routing protocol capabilities.
Answer: C
QUESTION 153
A network engineer has configured a tracking object to monitor the reachability of IP SLA 1. In
order to update the next hop for the interesting traffic, which feature must be used in conjunction
with the newly created tracking object to manipulate the traffic flow as required?
A.
B.
C.
D.
E.
F.
SNMP
PBR
IP SLA
SAA
ACLs
IGP
Answer: B
QUESTION 154
A route map uses an ACL, if the required matching is based on which criteria?
A.
B.
C.
D.
addressing information
route types
AS paths
metrics
Answer: A
QUESTION 155
Various employees in the same department report to the network engineer about slowness in the
network connectivity to the Internet. They are also having latency issues communicating to the
network drives of various departments. Upon monitoring, the engineer finds traffic flood in the
network. Which option is the problem?
A.
B.
C.
D.
network outage
network switching loop
router configuration issue
wrong proxy configured
Answer: B
87
QUESTION 156
Which type of handshake does CHAP authentication use to establish a PPP link?
A.
B.
C.
D.
one-way
two-way
three-way
four-way
Answer: C
QUESTION 157
Which two authentication protocols does PPP support? (Choose two.)
A.
B.
C.
D.
E.
WAP
PAP
CHAP
EAP
RADIUS
Answer: BC
QUESTION 158
Which statement is a restriction for PPPoE configuration?
A.
B.
C.
D.
Multiple PPPoE clients can use the same dialer interface.

Multiple PPPoE clients can use the same dialer pool.
A PPPoE session can be initiated only by the client.
A PPPoE session can be initiated only by the access concentrator.
Answer: C
QUESTION 159
Refer to the exhibit. Which statement about the configuration is true?
A. This configuration is incorrect because the MTU must match the ppp-max-payload that is defined.
B. This configuration is incorrect because the dialer interface number must be the same as the dialer
pool number.
C. This configuration is missing an IP address on the dialer interface.
D. This configuration represents a complete PPPoE client configuration on an Ethernet connection.
88
Answer: D
QUESTION 160
A company has their headquarters located in a large city with a T3 frame relay link that connects
30 remote locations that each have T1 frame relay connections. Which technology must be
configured to prevent remote sites from getting overwhelmed with traffic and prevent packet
drops from the headquarters?
A.
B.
C.
D.
traffic shaping
IPsec VPN
GRE VPN
MPLS
Answer: A
QUESTION 161
On which two types of interface is Frame Relay switching supported? (Choose two.)
A.
B.
C.
D.
E.
serial interfaces
Ethernet interfaces
fiber interfaces
ISDN interfaces
auxiliary interfaces
Answer: AD
QUESTION 162
In IPv6, SLAAC provides the ability to address a host based on a network prefix that is advertised
from a local network router. How is the prefix advertised?
A.
B.
C.
D.
routing table
router advertisements
routing protocol
routing type
Answer: B
QUESTION 163
Refer to the exhibit. Which option prevents routing updates from being sent to the access layer
switches?
89
A. DWS1(config-router)# passive-interface default

DWS2(config-router)# passive-interface default
B. ALS1(config-router)# passive-interface default
ALS2(config-router)# passive-interface default
C. DWS1(config-router)# passive-interface gi1/1
DWS1(config-router)# passive-interface gi1/2
D. ALS1(config-router)# passive-interface gi0/1
ALS1(config-router)# passive-interface gi0/2
Answer: C
QUESTION 164
Refer to the exhibit. Which option prevents routing updates from being sent to the DHCP router,
while still allowing routing update messages to flow to the Internet router and the distribution
switches?
90
A. DHCP(config-router)# passive-interface default

DHCP(config-router)# no passive-interface Gi1/0
Internet(config-router)# passive-interface Gi0/1
Internet (config-router)# passive-interface Gi0/2
B. Core(config-router)# passive-interface Gi0/0
Core(config-router)# passive-interface Gi3/1
Core(config-router)# passive-interface Gi3/2
DHCP(config-router)# no passive-interface Gi1/0
C. Core(config-router)# passive-interface default
Core(config-router)# no passive-interface Gi0/0
D. Internet(config-router)# passive-interface default
Core(config-router)# passive-interface default
DSW1(config-router)# passive-interface default
DSW2(config-router)# passive-interface default
Answer: C
QUESTION 165
A network engineer is considering enabling load balancing with EIGRP.
Which consideration should be analyzed?
A.
B.
C.
D.
EIGRP allows a maximum of four paths across for load balancing traffic.
By default, EIGRP uses a default variance of 2 for load balancing.
EIGRP unequal path load balancing can result in routing loops.
By default, EIGRP performs equal cost load balancing at least across four equal cost paths.
91
Answer: D
QUESTION 166
The OSPF database of a router shows LSA types 1, 2, 3, and 7 only.
Which type of area is this router connected to?
A.
B.
C.
D.
stub area
totally stubby area
backbone area
not-so-stubby area
Answer: D
QUESTION 167
An engineer is configuring a GRE tunnel interface in the default mode. The engineer has
assigned an IPv4 address on the tunnel and sourced the tunnel from an Ethernet interface. Which
option also is required on the tunnel interface before it is operational?
A.
B.
C.
D.
tunnel destination address

keepalives
IPv6 address
tunnel protection
Answer: A
QUESTION 168
Which protocol is used in a DMVPN network to map physical IP addresses to logical IP
addresses?
A.
B.
C.
D.
BGP
LLDP
EIGRP
NHRP
Answer: D
QUESTION 169
Which two routing protocols are supported by Easy Virtual Network? (Choose two.)
A.
B.
C.
D.
E.
RIPv2
OSPFv2
BGP
EIGRP
IS-IS
Answer: BD
QUESTION 170
92
Which statement is true?

A.
B.
C.
D.
RADIUS uses TCP, and TACACS+ uses UDP.

RADIUS encrypts the entire body of the packet.
TACACS+ encrypts only the password portion of a packet.
TACACS+ separates authentication and authorization.
Answer: D
QUESTION 171
Which two statements about AAA implementation in a Cisco router are true? (Choose two.)
A.
B.
C.
D.
E.
RADIUS is more flexible than TACACS+ in router management.

RADIUS and TACACS+ allow accounting of commands.
RADIUS and TACACS+ encrypt the entire body of the packet.
RADIUS and TACACS+ are client/server AAA protocols.
Neither RADIUS nor TACACS+ allow for accounting of commands.
Answer: BD
QUESTION 172
Which option is invalid when configuring Unicast Reverse Path Forwarding?
A.
B.
C.
D.
allow self ping to router

allow default route
allow based on ACL match
source reachable via both
Answer: D
QUESTION 173
Refer to the exhibit. Which option represents the minimal configuration that allows inbound traffic
from the 172.16.1.0/24 network to successfully enter router R, while also limiting spoofed
10.0.0.0/8 hosts that could enter router R?
A. (config)#ip cef
(config)#interface fa0/0
(config-if)#ip verify unicast source reachable-via rx allow-default
93
B. (config)#ip cef
(config-if)#ip verify unicast source reachable-via rx
C. (config)#no ip cef
(config-if)#ip verify unicast source reachable-via rx
D. (config)#interface fa0/0
(config-if)#ip verify unicast source reachable-via any
Answer: A
QUESTION 174
Which outbound access list, applied to the WAN interface of a router, permits all traffic except for
http traffic sourced from the workstation with IP address 10.10.10.1?
A. ip access-list extended 200
deny tcp host 10.10.10.1 eq 80 any
permit ip any any
B. ip access-list extended 10
deny tcp host 10.10.10.1 any eq 80
permit ip any any
C. ip access-list extended NO_HTTP
D. ip access-list extended 100
permit ip any any
Answer: D
QUESTION 175
Which two statements indicate a valid association mode for NTP synchronization? (Choose two.)
A.
B.
C.
D.
E.
The client polls NTP servers for time.

The client broadcasts NTP requests.
The client listens to NTP broadcasts.
The client creates a VPN tunnel to an NTP server.
The client multicasts NTP requests.
Answer: AC
QUESTION 176
Refer to the exhibit. Which command allows hosts that are connected to FastEthernet0/2 to
access the Internet?
94
A.
B.
C.
D.
ip nat inside source list 10 interface FastEthernet0/1 overload

ip nat outside source static 209.165.200.225 10.10.10.0 overload
ip nat inside source list 10 interface FastEthernet0/2 overload
ip nat outside source list 10 interface FastEthernet0/2 overload
Answer: A
QUESTION 177
Which statement describes what this command accomplishes when inside and outside interfaces
are correctly identified for NAT?
ip nat inside source static tcp 192.168.1.50 80 209.165.201.1 8080
extendable
A. It allows host 192.168.1.50 to access external websites using TCP port 8080.
B. It allows external clients coming from public IP 209.165.201.1 to connect to a web server at
192.168.1.50.
C. It allows external clients to connect to a web server hosted on 192.168.1.50.
D. It represents an incorrect NAT configuration because it uses standard TCP ports.
Answer: C
QUESTION 178
Refer to the exhibit. Which technology can be employed to automatically detect a WAN primary
link failure and failover to the secondary link?
95
A.
B.
C.
D.
HSRP
VRRP
IP SLA
multicast
Answer: C
QUESTION 179
In which two ways can NetFlow data be viewed? (Choose two.)
A.
B.
C.
D.
E.
CLI
NetFlow
built-in GUI
syslog server interface
web interface
Answer: AB
QUESTION 180
Drag and drop the Cisco Express Forwarding adjacency types from the left to the correct type of
processing on the right.
Answer:
96
QUESTION 181
Drag and drop the BGP states from the left to the matching definitions on the right.
Answer:
97
QUESTION 182
Drag and drop the IPv6 NAT characteristic from the left to the matching IPv6 NAT category on the
right.
Answer:
98
QUESTION 183
An engineer is asked to monitor the availability of the next-hop IP address of 172.16.201.25 every
3 seconds using an ICMP echo packet via an ICMP echo probe.
Which two commands accomplish this task? (Choose two.)
A.
B.
C.
D.
E.
F.
router(config-ip-sla)#icmp-echo 172.16.201.25 source-interface FastEthernet 0/0

router(config-ip-sla-echo)#timeout 3
router(config-ip-sla)#icmp-jitter 172.16.201.25 interval 100
router(config-ip-sla-echo)#frequency 3
router(config-ip-sla)#udp-echo 172.16.201.25 source-port 23
router(config-ip-sla-echo)#threshold 3
Answer: AD
99
About Lead2pass.com
Lead2pass.com was founded in 2006. We provide latest & high quality IT Certification Training
Exam Questions, Study Guides, Practice Tests. Lead the way to help you pass any IT Certification
exams, 100% Pass Guaranteed or Full Refund. Especially Cisco, CompTIA, Citrix, EMC, HP,
Oracle, VMware, Juniper, Check Point, LPI, Nortel, EXIN and so on.
Our Slogan: First Test, First Pass.

Help you to pass any IT Certification exams at the first try.
You can reach us at any of the email addresses listed below.

Sales: sales@lead2pass.com
Support: support@lead2pass.com
Technical Assistance Center: technology@lead2pass.com
Any problems about IT certification or our products, you could rely upon us, we will give you
satisfactory answers in 24 hours.
Our Official: http://www.lead2pass.com

300 101

Uploaded by

Copyright:

Available Formats

300 101

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

300 101

Uploaded by

Copyright:

Available Formats

What is the purpose of the document?

What is the purpose of the document?

What are the different ways to view NetFlow data?

What are the different ways to view NetFlow data?

Copyright 2006-2011 Lead2pass.com , All Rights Reserved.

all traffic to vty 0 4 from source 2001:DB8:0:4::32

You can disable the IP route cache globally.

strict mode, loose mode, and VRF mode

router(config)#access-list 101 deny ip 10.0.0.0 0.255.255.255 any log

The router will listen on port 4433 for HTTPS traffic.

router(config)#snmp-server host 172.16.201.28 traps version 2c CISCORO

Use the msec option to enable service time stamps.

secure copy protocol

when TCP traffic is in the same class as UDP

Active Authentication Phase and PPP Session Phase

distribute list 1 out

Cisco Express Forwarding has not been configured globally.

configuration of the specified flow exporter

The 4th octet of IP address (192.168.16.5) belongs to subnet 1 (4 to 7).

R3# show interface fa0/0

What type of route filtering is occurring on R6

Distribute-list using an ACL

This is a standard distribute list using access list number 1.

Clearly we see the actual key chain is named CISCO.

What is the advertised distance for the 192.168.46.0 network on R1?

What percent of R1's interfaces bandwidth is EIGRP allowed to use?

The Link ID of R3 (3.3.3.3) shows the age is 1858.

How many times was SPF algorithm executed on R4 for Area 1?

There is no default gateway.

incomplete ARP information

A. Traffic from the 172.16.0.0/16 network will be blocked by the ACL.

Disable CDP on the interface.

router(config-if)#ip helper-address 172.20.14.225

It interferes with encryption of the full IP payload.

Flow-label marking in 1280-byte or larger packets is enabled.

Execute the command ip tcp window-size 65536.

Frame Relay inverse ARP

It sets the EIGRP autonomous system number in a VRF.

inbound crypto map

It was obtained directly from the next-hop server.

a routing neighbor reachability issue

Drag and Drop Question

An IPv6 address is 128 bits long.

F. An IPv6 header contains the header checksum field.

IPv6 address for the host

Only one IPv6 address is assigned per node.

all hosts in a local segment

The OSPF adjacencies are cleared and initiated again.

OSPFv3 for IPv6 authentication is supported by SHA-1 authentication.

Select the best response.

R4(config)# ip default-network 10.0.0.0

The border router is using a proper seed metric for OSPF.

::/0 is the unspecified address, and ::/128 is the multicast address.

D. The area has no more than 10 routers.

Dev-1 is the DR because it has a higher OSPF router priority.

Select the best response.

They will appear in the OSPF routing table as type E1 routes.

Ensure that an interface has been configured with an IP address.

simplified Layer 3 network virtualization