Grounding Equipment: Catalog 3000 March 2013

G rou n d i n g Eq u i p m ent 3 0 00
Grounding
Equipment
Catalog 3000 March 2013
Phone: 573-682-5521 Email: hpsliterature@hubbell.com Web: hubbellpowersystems.com

March 2013
Page 3001
Temporary Grounding Equipment

Safe Working Practices
There are many reasons for temporary grounding to

protect personnel working on de-energized circuits,
including:
1. Induced voltage from adjacent energized lines
2. Fault-current feedover from adjacent lines
3. Lightning strikes anywhere on the circuit
4. Switching-equipment malfunction or human error
5. Accident-initiated contact with adjacent lines
Since any one of the above could result in re-energizing
the circuit, most utilities treat these potential dangers
as ever-present and impose strict temporary-grounding
work rules. Their crews experience often voices these
watchwords for the wise to heed:
If you cant see both ends, its hot and If it isn't
grounded, it isnt dead.
Vital Procedure Recommendations

Step One: Testing
With a test instrument, confirm the circuit to be worked
has been de-energized intentionally before ground sets
are applied
Step Two: Cleaning

For a good connection, scrub oxides and contaminants
from conductor, buswork or lattice contact points
Chance universal wire brushes make this easy
Serrated-jaw clamps also aid by penetrating surface
contaminants
Step Three: Connecting
Chance insulated Grip-All clampsticks are the proper

tools to apply grounding clamps
Various clampstick lengths and styles are available in
Catalog Section 2100, Insulated Hand Tools
To indicate energized conditions on overhead lines, (from left) Chance Auto Ranging Voltage Indicator, Digital
Voltage Detector and Multi-Range Voltage Detector. At far right, Energized Cable Sensor performs the same function
on URD cable with an exposed concentric neutral and elbows without test points.
See Catalog Section 2450, Instruments and Meters, for details and ordering information.
General Practices
On de-energized distribution lines, Chance recommends Double-Point grounding

This grounding is at both structures adjacent to worksite: Connect all three phases via ground set, then connect to
ground rod.
Plus a personal ground at the worksite, from any one phase to a cluster bar well below the workers feet
On a system without a neutral, Chance recommends connecting down leads to screw ground rods installed at least
20 feet from all structures and barricaded
Only for maintenance tasks during which grounds need not be replaced does Chance find acceptable the SinglePoint grounding method (at only the worksite: Connect all phases together and grounding plus personal ground,
as above)
Where adequate phase-to-phase clearances permit, Chance accepts the practice of grounding only the phase being
worked (in the same manner as personal ground, above)
Grounding Set Ratings
Reference:
Derived from
ASTM F 855,
Standard
Specifications
for Temporary
Protective
Grounds to be
Used on Deenergized Electric
Power Lines and
Equipment
Copyright ASTM
Reprinted with
permission.
Short Circuit PropertiesA

Withstand Rating,
Ultimate Rating/Capacity,B
Minimum
Symmetrical kA RMS, 60 Hz
Symmetrical kA RMS, 60 Hz
30
Continuous
Cable Size
15
30
6
15
cycles
Current
with Ferrule
cycles
cycles
cycles
cycles
(500
60
Rating, A
Installed
(250
(500
Copper Cable
(100
(250
MS)
cycles
RMS,
Equal or
MS)
MS)
Size
MS)
MS)
(1 S)
60 Hz
Larger Than
Grade
1
14
10
#2
29
18
13
9
200
#2
2
21
15
1/0
48
30
21
15
250
1/0
3
27
20
2/0
61
38
27
19
300
2/0
4
34
25
3/0
76
48
34
24
350
3/0
5
43
30
4/0
96
60
43
30
400
4/0
250 kcmil or
250 kcmil
6
54
39
two 2/0
114
72
51
36
450
or two 2/0
350 kcmil or
350 kcmil
7
74
54
two 4/0
159
101
71
50
550
or two 4/0
A Withstand and ultimate short circuit properties are based on performance with surges not exceeding 20% asymmetry factor
(see Appendices X3 and X4, ASTM F 855).
B Ultimate rating represents a symmetrical current which the clamp shall carry for the specified time.

Page 3002
March 2013
Temporary grounding practices should be reviewed on

a regular basis
As part of a total maintenance program, routine
reviews should be scheduled apart from sessions to set
new practices for system upgrades and additions
These basics should be included on a review checklist:
1. Clamp designs specific to each application,
2. Cable sized for fault-current potential (see table on
page 3002) and minimum-slack lengths
3. How construction affects placement of grounds
4. Work procedures outlined above
5. Inspect and test each grounding set
Chance Grounding-Set Tester
Ideal for performing function
#5 above
Checks the resistance in a
protective ground set
Can help locate problems
often remedied by simple
repairs
How-to video is included with
the tester
See Catalog Section 2450, Instruments and Meters,
for details and ordering information
Selecting grounding clamps and cable

The Chance grounding line comprises both ready-made sets and separate components for your specific needs.
Among the options and criteria to consider:
Functional fitSizes of the clamp types in this section
fault-current magnitude and full-time duration.
appear in ascending order of maximum-main-line size.
Certified test reports are available on request
By design, many clamps serve a wide size range for
Coordinated connectorsTerminal (either pressuretheir conductor type (cable, bus or tower)
type or threaded-type) selected for clamps dictates the
Adequate capacityPublished ratings for both clamps
and cable must withstand maximum-potential system
How to order a Grounding Set
cable ferrule type (either plain or threaded) to match
On-site handlingApplication clearances and fit (for

overhead conductors and ground wires, transmission
tower shapes, URD apparatus or substation buswork)
affect clamp and cable dimensions
In addition to the specifying criteria above, each part of a grounding set requires certain choices:
1. Clamps
ASTM designations for Type, Class and Grade given
for clamps shown in this section
2. Ferrules
Copper or aluminum
1. Clamps
Plain or threaded
3. Cable
Length required to reach application distances
2. Ferrules
ASTM Type I with black or yellow elastomer jackets
for temperatures from -40F (-40C) through +194F
(+90C)
ASTM Type III with clear thermoplastic jacket for
temperatures from +14F (-10C) through +140F
(+60) should be used only in well-ventilated areas
4. Support Stud
This option recommended on only one clamp to help
control lifting the set to the first clamp attachment
point
5. Shrink Tubing
This translucent option recommended for stress
relief and inspection of cable strands between
3. Cable
ferrule and jacket.
4. Support Stud
5. Shrink Tubing
Installation information
Several training aids available on request

Chance videos and technical manuals provide details on proper installation
Consult your Chance representative for any additional assistance

March 2013
Page 3003
Safety Reviews
C-Type Grounding Clamps
T6000465
Bronze body,
Smooth jaws,
Bronze eyescrew
with fine threads,
Tapped for 58-11 UNC threaded ferrule
or T6000466,
Drilled for 58-11 UNC threaded ferrule
C6001754
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads,
Tapped for 58-11 UNC
threaded ferrule
C6002275
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads,
Bronze pressure-type
terminals
Catalog Number
ELECTRICAL RATINGS
Continuous Current (AMPS)
Fault Current - 15 Cycles (AMPS)
MECHANICAL RATINGS
Recommended Torque (in.-lb.)
Main Line Range - Max.
Main Line Range - Min.

Jumper Range - Max.
Jumper Range - Min.
Weight Each
ASTM Designation
T6000790
Bronze body,
Smooth jaws,
Bronze T-handle/eyescrew
with fine threads,
threaded ferrule
C6002271
Bronze body,
Smooth jaws,
Bronze eyescrew
with fine threads,
threaded ferrule
C6002276
Aluminum body,
Serrated jaws,
Bronze eyescrew
with Acme threads,
Bronze pressure-type
terminals
T6002708
Aluminum body,
Serrated jaws,
Bronze eyescrew
with Acme threads,
threaded ferrule
C6001959
Bronze body,
Smooth jaws,
Bronze T-handle/eyescrew
with fine threads,
threaded ferrule
C6001743
Aluminum body,
Smooth jaws,
Bronze eyescrew
with fine threads,
threaded ferrule
C6001959
T6000465
T6000466
T6000790
C6002271
C6001754
C6002275
C6002276
T6002708
C6001743
250
21,000
15,000
400
43,000
30,000
350
27,000
20,000
400
43,000
30,000
400
43,000
30,000
400
43,000
30,000
400
43,000
30,000
200
477 kcmil
ACSR
(0.814)
#6 Sol. Cu.
(0.162)
1/0 Grd. Cable
w/Threaded
Stud
#2 Grd. Cable
w/Threaded
Stud
1 1/2 lb./0.7kg.
Type I
Class A
Grade 2
250
250
250
1033 kcmil
ACSR
(1.25)
250
250
250
750 kcmil
1033 kcmil
1033 kcmil
Str. Cu.
ACSR
ACSR
636 kcmil ACSR
(1.25)
(1.25)
(0.998)
#6 Sol. Cu.
#8 Sol. Cu.
#8 Sol. Cu.
#8 Sol. Cu.
(0.162)
(0.128)
(0.128)
(0.128)
4/0 Grd. Cable 2/0 Grd. Cable 4/0 Grd. Cable 4/0 Grd. Cable
w/Threaded
w/Threaded
w/Plain
w/Plain
Stud
Stud
Plug
Plug
#2 Grd. Cable #2 Grd. Cable #2 Grd. Cable #2 Grd. Cable
w/Threaded
w/Threaded
w/Plain
w/Plain
Stud
Stud
Plug
Plug
2 lb./0.9kg.
1 lb./0.5kg.
1 1/4 lb./0.6 kg. 1 1/4 lb./0.6kg.
Type I
Type I
Type I
Type I
Class A
Class A
Class A
Class B
Grade 5
Grade 3
Grade 5
Grade 5
1033 kcmil
ACSR
(1.25)
1000 kcmil Cu.

1590 kcmil
ACSR (1.50)
#8 Sol. Cu.
(0.128)
4/0 Grd. Cable
w/Threaded
Stud
#2 Grd. Cable
w/Threaded
Stud
1 1/4 lb./0.6kg.
Type I
Class B
Grade 5
#6 Sol. Cu.
(0.162)
4/0 Grd. Cable
w/Threaded
Stud
#2 Grd. Cable
w/Threaded
Stud
1 1/2 lb./0.7kg.
Type I
Class A
Grade 5

Page 3004
March 2013
C6002281
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads
Bronze pressure-type terminal
C6002255
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads,
Tapped for 58-11 UNC threaded
ferrule
G36051
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads,
C6000386
*Mounted Clamp
Aluminum body,
Serrated jaws,
Bronze eyescrew
with Acme threads,
Catalog Number
C6002281
C6002282
Aluminum body,
Serrated jaws,
Bronze eyescrew
with Acme threads
C6002255
C6002282
C6002256
C6002256
Aluminum body,
Serrated jaws,
Bronze eyescrew
with Acme threads,
Tapped for 58-11 UNC threaded
ferrule
T6003203
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads,
threaded ferrule
*C6000386
G36051
T6000658
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads,
Drilled for 58-11 UNC
threaded ferrule
T6003203
T6000658
ELECTRICAL RATINGS
400
400
400
400
400
400
400
400
Fault Current - 15 Cycles (amps)
Continuous Current (amps)
43,000
43,000
43,000
43,000
43,000
43,000
43,000
43,000
Fault Current - 30 Cycles (amps)
30,000
30,000
30,000
30,000
30,000
30,000
30,000
30,000
250
250
250
250
250
250
250
250
2" O.D. Bus
2" O.D. Bus
2" O.D. Bus
2" O.D. Bus
2" O.D. Bus
2" O.D. Bus
2" O.D. Bus
2" O.D. Bus
#6 Sol. Cu.
(0.162)
#6 Sol. Cu.
(0.162)
#6 Sol. Cu.
(0.162)
#6 Sol. Cu.
(0.162)
#6 Sol. Cu.
(0.162)
#6 Sol. Cu.
(0.162")
#6 Sol. Cu.
(0.162)
#6 Sol. Cu.
(0.162)
Jumper Range - Max.
4/0 Grd.
Cable
w/Plain Plug
4/0 Grd.
Cable
w/Threaded
Stud
4/0 Grd.
Cable
w/Plain Plug
4/0 Grd.
Cable
w/Threaded
Stud
4/0 Grd.
Cable
w/Plain Plug
4/0 Grd.
Cable
w/Plain Plug
4/0 Grd.
Cable
w/Threaded
Stud
4/0 Grd.
Cable
w/Threaded
Stud
Jumper Range - Min.
#2 Grd. Cable
#2 Grd. Cable
#2 Grd. Cable #2 Grd. Cable
#2 Grd. Cable
#2 Grd. Cable
#2 Grd. Cable #2 Grd. Cable
w/Threaded
w/Threaded
w/Threaded w/Threaded
w/Plain Plug
w/Plain Plug
w/Plain Plug w/Plain Plug
Stud
Stud
Stud
Stud
MECHANICAL RATINGS
Weight Each
ASTM Designation
2 lb./0.9kg.
134 lb./0.8kg.
2 lb./0.9kg.
134 lb./0.8kg.
Type I
Class A
Grade 5
Type I
Class A
Grade 5
Type I
Class B
Grade 5
Type I
Class B
Grade 5
Type II
Class B
Grade 5
134 lb./0.8kg. 134 lb./0.8kg. 134 lb./0.8kg.

Type I
Class A
Grade 5
Type I
Class A
Grade 5
Type I
Class A
Grade 5
*C6000386 has 1-1/4" x 6' Epoxiglas Pole and total weight of 334 lb. (1.7 kg.).

March 2013
Page 3005
G33672
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads,
Bronze pressure-type threads
C6001733
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads,
C6000375
Aluminum body,
Serrated jaws,
Bronze eyescrew
with Acme threads,
Dual drilled for 58-11 UNC threaded ferrule
Bus-Bar Grounding Clamps:
G3369
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads,
Catalog Number
C6000337
Aluminum body,
Smooth jaws,
Bronze eyescrew
with Acme threads,
G33672
C6001733
C6000375
G3369
C6000337
400
400
400
400
400
ELECTRICAL RATINGS
43,000
43,000
70,000
43,000
43,000
60,000
30,000
30,000
50,000
30,000
30,000
60,000
250
250
300
300
300
6-58 O.D. Bus
MECHANICAL RATINGS
2-12 O.D. Bus
2-12 O.D. Bus
3 O.D. Bus
4 x 4 Square
4.5 O.D. Bus
#4 Str. Cu.
(0.232)
#4 Str. Cu.
(0.232)
0.50 O.D.
Bus
4/0 Str. Cu.

(0.500)
3-12 O.D. Bus
Jumper Range - Max.
4/0 Grd. Cable

w/Plain Plug
4/0 Grd. Cable

w/Threaded Stud
4/0 Grd. Cable

w/Threaded Stud
4/0 Grd. Cable

w/Plain Plug
4/0 Grd. Cable

w/Plain Plug
Jumper Range - Min.
#2 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Threaded Stud
#2 Grd. Cable
w/Threaded Stud
#2 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Plain Plug
Weight Each
2-38 lb./1.1kg.
2-38 lb./1.1kg.
3 lb./1.4kg.
5-14 lb./2.4kg.
6 lb./2.7 kg.
Type I
Class A
Grade 5
Type I
Class A
Grade 5
Type I
Class B
Grade 7
Type I
Class A
Grade 5
Type I
Class A
Grade 6
ASTM Designation
Rating
with twin-grounding cables.

Page 3006
March 2013
G18102
Aluminum body,
Bronze upper jaw,
Smooth jaws,
Bronze eyescrew
with fine threads,
G36221
Aluminum body,
Smooth jaws,
Bronze eyescrew
with fine threads,
HG37061
*Mounted Clamp
Aluminum body,
Smooth jaws,
Bronze eyescrew
with fine threads,
Catalog Number
G18102
T6000806
Aluminum body,
Serrated jaws,
Bronze eyescrew
with fine threads,
G36221
*HG37061
T6000806
ELECTRICAL RATINGS
300
400
400
400
27,000
43,000
34,000
43,000
20,000
30,000
25,000
30,000
250
250
300
300
250 kcmil Str. Cu.

4/0 ACSR
(0.574)
566 kcmil Cu.

900 kcmil ACSR
(1.162)
566 kcmil Cu.

900 kcmil ACSR
(1.162)
1590 kcmil ACSR

(1.625)
#6 Sol. Cu.
(0.162)
#6 Sol. Cu.
(0.162)
#6 Sol. Cu.
(0.162)
0.5
Jumper Range - Max.
2/0 Grd. Cable

w/Plain Plug
4/0 Grd. Cable

w/Plain Plug
4/0 Grd. Cable

w/Plain Plug
4/0 Grd. Cable

w/Plain Plug
Jumper Range - Min.
#2 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Plain Plug
1-12 lb./0.6 kg.
1-12 lb./0.6 kg.
1-34 lb./0.8 kg.
Type I
Class A
Grade 3
Type I
Class A
Grade 5
Type II
Class A
Grade 4
Type I
Class B
Grade 5
MECHANICAL RATINGS
Weight Each
ASTM Designation
*HG37061 has 114" x 6' Epoxiglas Pole and total weight of 312 lb. (1.6 kg.).

March 2013
Page 3007
Snap-On (Duckbill-type) Grounding Clamps
Snap-On (Duckbill-type) Grounding Clamps
C6000198
*Mounted Clamp
Aluminum body,
Serrated jaws,
Bronze eyescrew
with Acme threads,
C6001734
Aluminum body,
Smooth jaws,
Bronze eyescrew
with fine threads,
C6000197
Aluminum body,
Serrated jaws,
Bronze eyescrew
with Acme threads,
Catalog Number
C6001757
Aluminum body,
Smooth jaws,
Bronze eyescrew
with fine threads,
C6000434
Aluminum body,
Serrated jaws,
Bronze eyescrew
with fine threads,
C6001734
*C6000198
C6000197
C6001757
C6000434
400
400
400
400
400
43,000
43,000
43,000
43,000
43,000
30,000
30,000
30,000
30,000
30,000
ELECTRICAL RATINGS
MECHANICAL RATINGS
250
250
250
250
250
566 kcmil Cu.

900 kcmil ACSR
(1.162)
950 kcmil Cu.

1510 kcmil ACSR
(1.506)
950 kcmil Cu.

1510 kcmil ACSR
(1.506)
2.5
950 kcmil Cu.

1510 kcmil ACSR
(1.506)
#6 Sol. Cu.
(0.162)
#6 Sol. Cu.
(0.162)
#6 Sol. Cu.
(0.162)
0.75
#6 Sol. Cu.
(0.162)
Jumper Range - Max.
4/0 Grd. Cable

w/Threaded Stud
4/0 Grd. Cable

w/Threaded Stud
4/0 Grd. Cable

w/Threaded Stud
4/0 Grd. Cable

w/Threaded Stud
4/0 Grd. Cable

w/Plain Plug
Jumper Range - Min.
#2 Grd. Cable
w/Threaded Stud
#2 Grd. Cable
w/Threaded Stud
#2 Grd. Cable
w/Threaded Stud
#2 Grd. Cable
w/Threaded Stud
#2 Grd. Cable
w/Plain Plug
1-12 lb./0.7 kg.
1-12 lb./0.7 kg.
2-14 lb./1.0 kg.
1-12 lb./0.7 kg.
Type I
Class A
Grade 5
Type II
Class B
Grade 5
Type I
Class B
Grade 5
Type I
Class A
Grade 5
Type I
Class B
Grade 5
Weight Each
ASTM Designation
*C6000198 has 114" x 6' Epoxiglas Pole and total weight of 312 lb. (1.6 kg.).

Page 3008
March 2013
G3405
3-Cluster Set
G3803
3-Cluster Set
with C-Type Aluminum-body clamps,
with Snap-On (Duckbill-type) Aluminum-body clamps,
Smooth jaws, Bronze eyescrews with Acme threads,

and 3-phase Aluminum cluster bar
with Bronze Pressure-type terminals
Smooth jaws, Bronze eyescrews with fine threads,

and 3-phase Aluminum cluster bar
with Bronze Pressure-type terminals
Important Note:
Cluster Sets are furnished as shown above. The center clamp is bolted to the cluster bar.
Typical fourth ground clamp
(not included in 3-Cluster Set,
must be ordered as separate item)
These drawings illustrate how Cluster Sets are to be connected, with grounding cable and a fourth clamp which
must be ordered separately.
For cable and ferrules, see page 3018-3019.
Catalog Number
G3405
G3803
ELECTRICAL RATINGS
350
400
27,000
34,000
20,000
25,000
MECHANICAL RATINGS
250
250
400 kcmil Str. Cu.

636 kcmil ACSR
(.998)
566 kcmil Cu.

900 kcmil AC
#8 Sol. Cu.
(0.12)
#6 Sol. Cu.
(0.162)
Jumper Range - Max.
2/0 Grd. Cable

w/Plain Plug
4/0 Grd. Cable

w/Plain Plug
Jumper Range - Min.
#2 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Plain Plug
Weight Each
4 12 lb./2 kg.
6 58 lb./3 kg.
Type I
Class A
Grade 3
Type I
Class A
Grade 4
ASTM Designation

March 2013
Page 3009
Cluster Grounding Clamps
Tower & Flat-Face Grounding Clamps
C6002232
Bronze body,
Serrated jaws,
Bronze eyescrew
with Acme threads,
or T6003196,
G33633SJ
Aluminum body,
Serrated jaws,
Bronze eyescrew
with fine threads,
C6001735
Aluminum body,
Serrated jaws,
Bronze eyescrew
with fine threads,
C6002231
Bronze body,
Serrated jaws,
Bronze T-handle
with Acme threads,
or T6003195,
G33634SJ
Aluminum body,
Serrated jaws,
Bronze T-handle
with fine threads,
T6001798
Aluminum body,
Serrated jaws,
Bronze T-handle
with Acme threads,
Catalog Number
C6002232
G33633SJ
C6001735
C6002231
G33634SJ
T6001798
ELECTRICAL RATINGS
400
400
400
400
400
400
43,000
27,000
27,000
43,000
27,000
27,000
30,000
20,000
20,000
30,000
20,000
20,000
MECHANICAL RATINGS
250
250
250
250
250
250
112 Angles
112 Flat
112 Angles
112 Flat
112 Angles
112 Flat
112 Angles
112 Flat
112 Angles
112 Flat
112 Angles
112 Flat
1
8
1
8
Jumper Range - Max.
4/0 Grd. Cable

w/Threaded Stud
2/0 Grd. Cable

w/Plain Plug
Jumper Range - Min.
#2 Grd. Cable
w/Threaded
Stud
#2 Grd. Cable
w/Plain
Plug
#2 Grd. Cable
w/Threaded
Stud
2 lb./0.9 kg.
158 lb./0.7 kg.
Type I
Class B
Grade 5
Type I
Class B
Grade 3
Weight Each
ASTM Designation
2/0 Grd. Cable

4/0 Grd. Cable
w/Threaded Stud w/Threaded Stud
1
8
2/0 Grd. Cable

w/Plain Plug
2/0 Grd. Cable

w/Threaded Stud
#2 Grd. Cable
w/Threaded
Stud
#2 Grd. Cable
w/Plain
Plug
#2 Grd. Cable
w/Threaded
Stud
112 lb./0.7 kg.
2 lb./0.9 kg.
158 lb./0.7 kg.
112 lb./0.7kg.
Type I
Class B
Grade 3
Type III
Class B
Grade 5
Type III
Class B
Grade 3
Type III
Class B
Grade 3

Page 3010
March 2013
G33631
Bronze body,
Serrated jaws,
Bronze eyescrew
with fine threads,
C6000085
Aluminum body and retainer,
Bronze scrubber-type contact pads,
Bronze T-handle
with fine threads,
G33632
Bronze body,
Serrated jaws,
Bronze T-handle
with fine threads,
Catalog Number
C6001783
Bronze body,
Serrated jaws and retainers,
G33631
G33632
C6000085
C6001783
ELECTRICAL RATINGS
400
400
400
400
27,000
27,000
43,000
43,000
20,000
20,000
30,000
30,000
MECHANICAL RATINGS
250
250
250
112 Angles
112 Flat
112 Angles
112 Flat
4 Structural
Angles
1
8
1
8
2 Structural
Angles
1
8
Jumper Range - Max.
2/0 Grd. Cable

w/Plain Plug
2/0 Grd. Cable

w/Plain Plug
4/0 Grd. Cable

w/Plain Plug
4/0 Grd. Cable

w/Threaded Stud
Jumper Range - Min.
#2 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Threaded Stud
Weight Each
212 lb./1.1 kg.
212 lb./1.1 kg.
334 lb./1.1 kg.
5 lb./2.25 kg.
Type I
Class B
Grade 3
Type III
Class B
Grade 3
Type III
Class B
Grade 5
Type III
Class B
Grade 5
ASTM Designation
300
3
4
x 5Angles or
Flats
5 Rod
8

March 2013
Page 3011
Tower & Flat-Face Grounding Clamps
All-Angle Grounding Clamps

Aluminum Bodies with Serrated Jaws
For installation ease, jaws pivot 75 left or right.
HG42296SJ
*Bronze Pressure Terminal
(Clamp same as G42291SJ)
G42291SJ
*Pressure Terminal
* For adapter to convert to threaded terminal, see Page 3019.
Catalog Number
G42291SJ
HG42296SJ
ELECTRICAL RATINGS
400
400
43,000
43,000
30,000
30,000
MECHANICAL RATINGS
Jumper Range - Max.
Jumper Range - Min.
Weight Each
ASTM Designation
250
250
954 kcmil ACSR

(1.196)
954 kcmil ACSR

(1.196)
#2 Cu. (.258)
#2 Cu. (.258)
4/0 Grd. Cable

w/Plain Plug
#2 Grd. Cable
w/Plain Plug
4/0 Grd. Cable

w/Plain Plug
#2 Grd. Cable
w/Plain Plug
2 lb./0.9 kg.
414 lb./2.0 kg.
Type I
Class B
Grade 5
Type II
Class B
Grade 5
Mounted Clamps supplied with 114" x 6' Epoxiglas Pole.
G422810SJ
HG422816SJ
(Clamp same as G4228-10SJ)
C6001732
T6001693
Tapped for 58-11 UNC threaded ferrule Tapped for 58-11 UNC
threaded ferrule
(Two single serrated jaws,
for pothead and bus applications)
* For adapter to convert to threaded terminal, see Page 3019.
Catalog Number
G422810SJ
HG422816SJ
T6001693
C6001732
ELECTRICAL RATINGS
400
400
400
400
43,000
43,000
43,000
43,000
30,000
30,000
30,000
30,000
MECHANICAL RATINGS
Jumper Range - Max.
Jumper Range - Min.
Weight Each
ASTM Designation
250
250
250
250
2.88
2.88
2.88
2.88
#2 Cu. (.258)
#2 Cu. (.258)
#2 Cu. (.258)
#2 Cu. (.258)
4/0 Grd. Cable

w/Plain Plug
#2 Grd. Cable
w/Plain Plug
4/0 Grd. Cable

w/Plain Plug
#2 Grd. Cable
w/Plain Plug
4/0 Grd. Cable

w/Threaded Stud
#2 Grd. Cable
w/Threaded Stud
4/0 Grd. Cable

w/Threaded Stud
#2 Grd. Cable
w/Threaded Stud
314 lb./1.5 kg.
514 lb./2.4 kg.
314 lb./1.5 kg.
314 lb./1.5 kg.
Type I
Class B
Grade 5
Type II
Class B
Grade 5
Type I
Class B
Grade 5
Type I
Class B
Grade 5
Mounted Clamps supplied with 114" x 6' Epoxiglas Pole.

Page 3012
March 2013
Apparatus Grounding Clamps

Ball-and-socket design for multiple uses
Fault Current Ratings

43,000 Amps 15 cycles

30,000 Amps 30 cycles
Recommended Installing Torques:

Eyescrew 250 inch-pounds *Ball Stud 300 inch-pounds
Long stud shank accepts
most types of grounding
clamps
Socket clamps provide
multi-angle attachment of
grounds
Clamp C6002100
Drilled for 58-11 UNC
threaded ferrule
or
Clamp C6002101
threaded
ferrule
______
Clamp T6002320
threaded
ferrule
______
Clamp C6002300 with

pressure
terminal
______
for plain-plug ferrule

for threaded stud ferrule on #2 to 4/0 groundon #2 to 4/0
ing cable
grounding cable
for threaded stud ferrule

Weight, each clamp on this page: 1 lb. / 0.45 kg.
on #2 to 4/0
grounding cable
414"
*Standard
Ball Stud C6002102
5 "
8
218"
(12-13UNC)
Weight, each:
lb. / 0.23 kg.
11316"
3.3"
112"
1
2
*Female-Thread
Ball Stud T6002867
5 "
8
1"
internal threads (12-13UNC)
dia. shank
dia. shank
Weight, each:
2 lb./0.23 kg.
*Long Ball Stud T6002364 3" nominal shank length

Weight, each: 34 lb./0.34 kg.
7"
5 " dia. shank
8
(1
234"
2-13UNC)
31516"
*Ball-studs do not interchange with system on page 3014.
Grounding Stud Cover fits onto 1" ball-studs of Apparatus Grounding Clamps above
Features & Applications
Flexible cover fits only C6002102 or T6002364 ball-studs

Made with same material as Chance line hose
Nonconductive cover may help prevent flashover on
ball studs installed in enclosed switchgear, switchyards
or substations
Cover is not intended for personnel protection and
should not be considered as insulative cover-up
equipment
Resilient ozone/corona-resistant thermo-plastic
elastomer does not absorb water
Special formulation resists aging/checking and retains
high-visibility orange color
Catalog No.
Description
Weight
C4060416
Grounding Stud Cover
1 oz. (28 g.)
Snap-fit keeps cover

in place
58"-I.D. loop at top
permits hot-line
tools to pop it on
and off
Chance silicone
lubricant C4002320
or C4170287 may
ease installation
and removal

March 2013
Page 3013
For restricted-space applications and as a truckgrounding system, this compact design delivers a highcurrent rating usually associated with only large clamps
Applies to a wide range of switching equipment,
including:
o Industrial metalclad gear
o Substations indoors and out
o Distribution overhead and underground
For trucks, a *ball stud permanently mounts on each
body
For three-phase livefront set, see page 3015
Two clamp styles and three ball-stud lengths adapt to
many applications
Clamp bodies, eyescrews and *ball-studs are bronze
alloy
Tin-plated ball-studs have nominal 1"-diameter ball
and stud to fit NEMA terminal pads
Lockwasher and nut are silicone bronze
ASTM Designation of Type I, Class A, Grade 5 for any of
these clamps is met if associated grounding-cable sets
are fitted with 58" copper ferrules as on page 3019
Three-Way Grounding Clamp for *ball-stud, conductors, busbars

Compact design delivers high-current rating associated
with large clamps
For grounding trucks or other equipment, *ball stud
permanently mounts on each body with furnished
lockwasher, flat washer and nut
Removable stud has recessed-hex end fitting for
through-mounting versatility
Clamp body is aluminum
Acme-threaded eyescrew and *ball-stud are bronze
alloy
Tin-plated ball-stud has 20mm (0.788") diameter ball,
78"-hex fitting and 1-12"-long 12"-13 threads to fit
NEMA terminal pads
ASTM Designation of Type I, Class A, Grade 5 is met if
associated grounding-cable sets are fitted with copper
ferrules as on page 3018
Clamp Main Line Range

By supporting other clamps in three-phase sets, ball
studs reduce installation labor
This can contribute to safety and minimize the number
of clamp connections per conductor in an overhead
grounding scheme
*Ball-studs mount without furnished washers in holes
of lower clamp boss
The tapped holes ship with plastic plugs
Clamp terminal is tapped for 58"-11 UNC threadedstud ferrules on grounding cable from #2 through 4/0
Versatile clamp serves such temporary-grounding uses as:
o A truck-grounding system
o On industrial metalclad switchgear
o Substation buswork, indoors and out
o Overhead, underground and substation switches
o Three-phase ground sets with special, multi-angle
*ball studs
Bare Conductors from #8 Sol. Cu. through 636 ACSR

Flat Busbar through 14" x 1-14" maximum
Ball-Stud 20mm (0.788") only
Fault current ratings:
43,000 amps 15 cycles

30,000 amps 30 cycles
Recommended Installing Torques:
Eyescrew 250 inch-pounds *Ball Stud 300 inch-pounds
Catalog No.
C6002316
C6002317
Description
Weight, each
Three-Way Clamp Body only
112 lb./0.68 kg.
*20mm (0.788") diameter Ball
Stud with flat washer, lockwasher 38 lb./0.2 kg.
and nut
*Ball-stud does not interchange with system on

page 3013.
Penetrator clamps, ground

sets for underground cable
C6001625
C6001626
T6002233
T6001922
For temporary grounding of underground distribution

Cable with jacket over concentric neutral, special
clamps help ensure contact with center conductor
Chisel-point clamp main-line capacity is 1-12"
C-Type clamp in Chisel Sets fits conductors from #6
(0.162") to 636 kcmil ACSR (0.998")
Spike-point clamp main-line capacity is 2-12"
C-type clamp in Spike Set fits conductors from #6
(0.162") to 2" O.D. bus
Screw-type copper-clad ground rod in sets indicated is
24" long for easy handling
Helix (spiral) and handle are bronze
Each set includes:
o 6-ft. of #2 copper clear-jacket ground cable and
ferrules
o A penetrator clamp (choice of hardened-steel 12"wide chisel or conical spike)
o C-type grounding clamp
Catalog No.
C6001626
P6001623P
T6002234
C6001625
T6001922
P6001969P
T6002233
Description
Chisel Clamp only
Replacement Chisel Point
Chisel Set with Ground Rod
Chisel Set without Ground Rod
Spiked Clamp only
Replacement Spike Point
Spiked Set with Ground Rod
Weight, each
134 lb./0.8 kg.
2 oz./0.09 kg.
934 lb./4.4 kg.
412 lb./2 kg.
134 lb./0.8 kg.
2 oz./0.09 kg.
8 lb./3.6 kg.

Page 3014
March 2013
Underground Distribution Grounding Sets

Grounded Parking Bushing Sets for Single- or Three-Phase Switches & Transformers
Set includes a loadbreak bushing and bronze ground clamp T6000466 connected by a 4 yellow 1/0 cable
Tin-plated copper connector joins cable to bushing
Threaded copper ferrule connects the cable to the clamp
Fault current rating for each set: 10,000 amps for 10 cycles
Catalog No.
T6003091
T6003092
*Application
15kV
25 & 35kV small interface
Weight, each
8 lb. / 3.6 kg.
9 lb. / 4.09 kg.
Grounding Elbow Sets for Single- or Three-Phase Switches & Transformers

Set includes:
o Yellow-jacketed elbow for the voltage-class indicated below
o Six feet of 1/0 copper grounding cable with yellow jacket
o Bronze ground clamp T6000466
15kV set
25 & 35kV small interface set
35 kV large interface set
4 lb./1.80 kg.
6 lb./2.7 kg.
8 lb./3.63 kg.
Three-Phase Grounding Elbow Sets for Switches & Transformers

Each of these sets consists of:
o A three-way terminal block assembly
o Three 6 lengths of 1/0 copper ground cable with yellow jacket
o A bronze ground clamp T6000466
o Three yellow elbows
C6003102
15kV set
C6003103
25 & 35kV small interface set
PSC6003103003 35kV large interface set
14.5 lb./6.5 kg.

15 lb./6.75 kg.
16 lb./7.25 kg.
Replacement Parts: Grounding Elbow ONLY

215GEHSG 15kV - elbow only
1.9 lb./0.88 kg.
225GEHSG 25 & 35kV small interface - elbow only 2.0 lb./0.9 kg.
235GEHSG 35kV large interface - elbow only
4.0 lb./1.8 kg.
All Copper Connector ONLY

200LUGC6
200LUGC7
for 1/0 Grounding Cable

for 2/0 Grounding Cable
1.8 oz./40 g.
1.8 oz./40 g.
Elbow Probes ONLY

215LBP
225LBP
235LBP
15 kV Probe
25 kV Probe
35 kV Probe
5.3 oz./150.3 g.
7.0 oz./198.4 g.
1.0 lb./0.45 kg.
Temporary Grounding Sets for Live-Front Switches and Transformers

C6000758
C-Clamp Set
15 lb./6.8 kg.
Fault current ratings: 21,000 amps for 15 cycles or15,000 amps for 30 cycles
C-clamps are Cat. No. T600-0466.
C6000758
Each C-Clamp set includes:
ASTM Type I,
o A three-way aluminum terminal block
Class A, Grade 2
o Four bronze ground clamps
o Three 6 lengths of 1/0 copper clear-jacket ground cable with threaded-stud ferrules
T6002246
Ball Socket Set
16.5 lb./7.4 kg.
Fault current ratings: 27,000 amps for 15 cycles or20,000 amps for 30 cycles
T6002246
Each Ball-Stud set includes:
ASTM Type I,
o A three-way copper terminal block
Class A, Grade 3
o Four bronze ground clamps
o Three 6 lengths of 2/0 copper clear-jacket ground cable with threaded-stud ferrules
T6002375
Flat-Face Clamp Set
15.5 lb./7 kg.
Fault current ratings: 21,000 amps for 15 cycles

or15,000 amps for 30 cycles
T6002375
Each set Includes:
ASTM Type III,
A four-way bronze terminal block
Class B, Grade 2
One 6 and three 4 lengths of 1/0 copper clear-jacket ground cable with
shrouded plain-plug copper ferrules
Three aluminum ground clamps with bronze eyescrews (G33633SJ)
One with bronze T-handle (G3363-4SJ)
*For storage bag T6000865, see page 3021.

March 2013
Page 3015
C6000729
T6002131
C6001927
Overhead Distribution Grounding Sets

with Pressure-Type Terminals
These complete sets of ground clamps, cable and

accessories
All equipment needed for many types of distribution
structures in easy-to-use kits Ferrules are factory
crimped to the grounding cable
Each kit comes with C6002276 clamps
Can be used on conductors ranging from #8 to 1033
kcmil ACSR
These kits were designed for use on the following types of

structures:

7.2/12.5 kV.........................A1 through C24

14.4/24.9 kV.......................VA1 through VC9-3

46 kV ...........................TP1 through TP5

69 kV ...........................TS1 through TS3-2
The tables below list the components completely assembled in
each of the Distribution Grounding Sets.
#2 Grounding Cable Set* (44 lb./20 kg.)

Catalog No. T6000641 consists of:
Item
A
B
C
Chance grounding clamps, ferrules and cable meet ASTM F 855.
D
E
F
Description
Serrated jaw, "C" Clamp
Cat. No. C6002276
Ground Cluster Support
#2 Copper Ground Cable
Cat. No. S6449
#2 Plain Plug Ferrules
Clamp Support Stud
Screw Ground Rod
Quantity
10
1
60 ft.
10
3
1
Information
For Plain Plug ferrules
Cat. No. T6001549
3 Cables 6 ft. long
1 Cable 12 ft. long
1 Cable 30 ft. long
Cat. No. C6002626
Cat. No. G3626
Cat. No. G3370
1/0 Grounding Cable Set* (58 lb./26 kg.)

G3370
Item
A
B
C
G3626
D
E
F
Description
Cat. No. C6002276
1/0 Copper Ground Cable
Cat. No. S7568
1/0 Plain Plug Ferrules
Clamp Support Stud
Screw Ground Rod
Quantity
10
1
60 ft.
10
3
1
Information
Cat. No. T6001549
3 Cables 6 ft. long
1 Cable 12 ft. long
1 Cable 30 ft. long
Cat. No. C6002627
Cat. No. G3626
Cat. No. G3370

C6002276
Main Line Range
Maximum 1033 kcmil ACSR (1.25")
Minimum #8 Solid Copper (0.128")
Item
A
B
C
D
E
F
Description
Cat. No. C6002276
Cat. No. S6450
Clamp Support Stud
Screw Ground Rod
Quantity
10
1
60 ft.
10
3
1
Information
Cat. No. T6001549
3 Cables 6 ft. long
1 Cable 12 ft. long
1 Cable 30 ft. long
Cat. No. C6002628
Cat. No. G3626
Cat. No. G3370

Item
A
B
C
D
E
F
T6001549
Description
Cat. No. C6002276
Cat. No. S6451
Clamp Support Stud
Screw Ground Rod
Quantity
10
1
60 ft.
10
3
1
Information
Cat. No. T6001549
3 Cables 6 ft. long
1 Cable 12 ft. long
1 Cable 30 ft. long
Cat. No. C6002629
Cat. No. G3626
Cat. No. G3370
*For storage bag T600-0865, see page 3021.

Page 3016
March 2013
Cutout Grounding Clamps

Bronze clamp used to ground bottom hinge contact
on cutouts used on distribution riser poles or where
grounding is required
Fits these cutouts:
o Chance F2, F3, and C Cutouts
o Westinghouse LDX, Southern States B-80
o Southern States Series 63
o Joslyn; S&C Type SX
o McGraw-Edison LMO, and GE Durabute
Clamp can be installed with or without grounding
cable
Serves as a warning and helps avoid accidental closing
of cutout
Clamps drilled terminal accepts threaded-stud cable
ferrules
Also accepts threaded L-Stud and T-Stud Terminals (34"
diameter bronze) for use with conventional groundclamp cable sets
Fault Current rating: 20,000 amps for 30 cycles
C6000785
C600-0785
with T-Stud
T6002408
T-Stud Terminal
C6000862
Switch Blade Grounding Clamps

Attaches temporary ground to open switch during deenergized maintenance
Helps keep ground lead away from energized switch
jaw
Shaped to fit blades of Chance Type M3 Disconnect
switches
Drilled terminal accepts threaded-stud ferrules on
grounding cable from #2 through 4/0
Also accepts threaded L-Stud Terminal (34" diameter
bronze) for use with conventional ground-clamp cable
sets
C6000841
L-Stud Terminal
ASTM Designation:
Type I, Class A, Grade 5
Fault Current ratings: 30,000 amps for 30 cycles

43,000 amps for 15 cycles
with L-Stud Terminal: 20,000 amps for 30 cycles
Recommended torque: 250 inch pounds
3 x 1 " flat through 21 " x 1 " flat
Main Line Range:
4"
8
2
4
Catalog No.
Description
Weight, each
C6002145
Plain eyescrew Switch

Clamp
312 lb./1.7 kg.
C6002146
T-handle/eyescrew Clamp
312 lb./1.7 kg.
C6000841
L-Stud Terminal only
1 lb./0.5 kg.
C6002145
Plain Eyescrew
C6002146
T-handle/eyescrew

March 2013
Page 3017
Substation Grounding Sets

with Pressure-Type Terminals
For grounding substation bus when de-energized for

maintenance
Makes workmens job safer and easier
Large capacity bus clamps are available in mounted
versions
Reaches any manageable height
Increases workers lifting capabilities
Plastisol coated, Shepherd Hook Lift Stick, with block
and rope assembly
Reduces capacity clamps on overhead bus
Two sizes of mounted clamps are available:
o C6000618 has 6-58" bus capacity, utilizing a
C6000337 ground clamp mounted on 1-14" x 9 ft.
Epoxiglas Pole
o C6000619 has 4" bus capacity, utilizing a G3369
ground clamp mounted on 1-14" x 8'10" Epoxiglas
Pole
Cables, ferrules and small grounding clamps should be
ordered separately
C6000619
C6000618
Accessories
C6000617 Lift Hook Assembly, 114" x 8'8" Epoxiglas
pole, includes block and rope assembly.
C6000620 114" x 12' Extension Pole (middle section).
C6000621 114" x 8' Bottom Pole.
Catalog Number
C6000618
C6000619
ELECTRICAL RATINGS
400
400
43,000
43,000
30,000
30,000
MECHANICAL RATINGS
Jumper Range - Max.
Jumper Range - Min.
Weight Each
ASTM Designation
250
250
658 Angles
412 Angles
412 Round
Bus
4/0 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Plain Plug
1/0 Str. Copper

(0.368)
4/0 Grd. Cable
w/Plain Plug
#2 Grd. Cable
w/Plain Plug
10 lb./4.5 kg.
914 lb./4.2 kg.
Type II
Class A
Grade 5
Type II
Class A
Grade 5
C6000617
C6000621
Bottom Pole
C6000620
Extension Pole
T6000891
Electro-Static Precipitator
Grounding Tool Set
Simple Safety Procedures
Drains off static charges that remain on collector
plates after electrostatic-precipitator pollution-control
equipment is de-energized
When electrical system of precipitator is de-energized:
o First, secure the tools grounding clamp to a known
ground
o Next, use insulated handle to bring the Copper hook
in contact with the precipitator collector plates
o Contact hook hangs from collector plates (with the
grounding clamp still attached to ground) while
service is performed on precipitator
o When maintenance is completed, use insulated
handle to remove contact hook from collector plates
o Finally, remove the ground clamp before reenergizing the precipitator
Epoxiglas handle (42" x 1-14") meets OSHA electrical

requirements
Gives operator sufficient added reach needed to make
contacts
Contact hook of 98%-conductive Copper is doublebolted to handle
T-handle aluminum grounding clamp with serrated
flat-face jaw ensures proper bonding
Jaws open to 1-12" for attachment to grounded
structural angles, flats or rods
Extra-flexible (1638 strands) Copper grounding cable,
7 ft., with clear jacket fitted with copper terminal at
each end gives high current-carrying capability
Catalog No.
T6000891
Description
Electrostatic Grounding Set
Weight, each
7 lb./3.2 kg.

Page 3018
March 2013
Chance grounding ferrules and cable meet

requirements of ASTM F 855; see table, page 3002.
Grounding Ferrules
See ordering tables for crimping-die sizes applicable.
Selection Criteria
Unshrouded ferrules
Shrouded ferrules overlap onto the grounding cable

jacket for stress relief to the terminal. Two crimps
secure the ferrule against the bare strands and one
crimp applies on the jacket
Unshrouded ferrules are available with shrink tubing
that overlaps the bare cable conductor and jacket for
stress relief
Available either factory-installed in pairs on any cable
length specified or as separate individual units, the
ferrules install simply with a hydraulic crimping tool.
Complete illustrated installation instructions come with
the ferrules and include a table for the crimping die
sizes to use
Two crimps
Cable
Shrouded ferrules
Section A
Sect. B
Cable
Copper ferrules
Shrouded plain copper ferrules

Burndy Die No.
1 unit each,
or equivalent
not installed
Catalog No.
Sect. A
Sect. B
C6002630
U165
U166
C6002631
U165
U168
C6002632
U165
U-L
C6002633
U166
U-L
Cable
Size,
AWG
#2
1/0
2/0
4/0
Unshrouded plain copper ferrules

1 unit each,
Burndy Die No.
not installed
or equivalent
Catalog No.
C6002614
U165
C6002615
U165
C6002616
U165
C6002617
U166
Shrouded threaded copper ferrules

C6002622
U165
U166
C6002623
U165
U168
C6002624
U165
U-L
C6002625
U166
U-L
#2
1/0
2/0
4/0
Unshrouded threaded copper ferrules

C6002606
U165
C6002607
U165
C6002608
U165
C6002609
U166
Cable
Size,
AWG
#2
1/0
2/0
4/0
Threaded-stud type for tapped or drilled grounding-clamp terminals

#2
1/0
2/0
4/0
Tin-Plated Copper ferrules
Plain-plug type for pressure-type grounding-clamp terminals

Shrouded plain tin-plated copper ferrules
C6003119
U165
U166
C6003120
U165
U168
C6003121
U165
U-L
C6003122
U166
U-L
#2
1/0
2/0
4/0
Unshrouded plain tin-plated copper ferrules

C6003111
U165
#2
C6003112
U165
1/0
C6003113
U165
2/0
C6003114
U166
4/0

Shrouded threaded tin-plated copper ferrules
C6003115
U165
U166
C6003116
U165
U168
C6003117
U165
U-L
C6003118
U166
U-L
Anderson
#2
1/0
2/0
4/0
Unshrouded threaded tin-plated copper ferrules

C6003107
U165
#2
C6003108
U165
1/0
C6003109
U165
2/0
C6003110
U166
4/0
die-less VERSA-CRIMP compression tools require no dies and are capable of making these crimped connections. If using
another crimp tool brand, contact that manufacturer for Burndy die equivalents.
Copper Grounding Cable
Extra-flexible for handling ease yet strong and tough

for long wear
Jacketing is smooth, abrasion, weather and oil resistant
In accordance with applicable ASTM Specifications,
marked with AWG size approximately every 4 feet
Yellow and black jackets are T-prene rubber compound
with -20F recommended low temperature
Clear jackets (which allow visual inspection of strand
conditions) are ultraviolet-inhibited Poly Vinyl Chloride
(PVC)
Recommended low temperature for PVC-jacketed cable
is 0F
Extra-flexible cables, because of their extra-fine strands
Require termination ferrules when used with ground
clamps
Either aluminum or copper ferrules may be used with copper

cable.
Catalog
Size
Diameter Approx. O.D. Approx. Wt.
Strands*
Number
AWG
(Inches)
(Inches)
(lb./1,000 ft.)
Yellow-Jacket Copper Cable
S6116
#2
665
0.32
0.55
280
S6117
1/0
1045
0.41
0.66
425
S6118
2/0
1330
0.47
0.73
520
S6119
4/0
2109
0.59
0.87
760
Clear-Jacket Copper Cable
S6449
#2
665
0.344
0.53
289
S7568
1/0
1050
0.445
0.63
520
S6450
2/0
1323
0.487
0.70
546
S6451
4/0
2107
0.616
0.84
841
Black-Jacket Copper Cable
S3713
#2
665
0.32
0.55
280
S3715
1/0
1045
0.41
0.66
425
S3712
2/0
1330
0.47
0.73
510
S3714
4/0
2109
0.59
0.87
760
*Varies with manufacturer.

March 2013
Page 3019
Aluminum ferrules
Shrouded plain aluminum ferrules
1 unit each,
not installed
Catalog No.
C6002626
C6002627
C6002628
C6002629
Burndy Die No.

or equivalent
Sect. A Sect. B
U165
U166
U165
U168
U165
U-L
U249
U-L
Cable
Size,
AWG
#2
1/0
2/0
4/0

Visual inspection of
cable condition through
clear heat-shrink tube
determines breakage or
corrosion that otherwise
requires continuity test
Factory-assembled units
expose 12" of cable
strands at junction point
Factory-crimped, above
Unshrouded plain aluminum ferrules

1 unit each,
not installed
Catalog No.
C6002610
C6002611
C6002612
C6002613
Burndy Die No.

or equivalent
U165
U165
U165
U249
Cable
Size,
AWG
#2
1/0
2/0
4/0
Shrink tubing for plain ferrules

Clear heat-shrink tubes limit corrosion
Excludes moisture
Stress-relief for cable jacket and ferrule-to-stranding
connection
Lengths
Part No.
5"
P6001593P
7"
P6001982P
9"
P6002069P
Anderson die-less VERSA-CRIMP compression tools require no dies and are capable of making these crimped
connections. If using another crimp tool brand, contact that manufacturer for Burndy die equivalents.

Shrouded threaded aluminum ferrules
1 unit each,
not installed
Catalog No.
C6002618
C6002619
C6002620
C6002621
Burndy Die No.

or equivalent
Sect. A Sect. B
U165
U166
U165
U168
U165
U-L
U249
U-L
Cable
Size,
AWG
#2
1/0
2/0
4/0
Visual inspection of cable

condition through clear
heat-shrink tube allows
inspection for breakage or
corrosion that otherwise
requires continuity test
Factory-assembled units
expose 12" of cable strands
at junction point
Factory-crimped, above
Unshrouded threaded aluminum ferrules

1 unit each,
not installed
Catalog No.
C6002602
C6002603
C6002604
C6002605
Burndy Die No.

or equivalent
U165
U165
U165
U249
Cable
Size,
AWG
#2
1/0
2/0
4/0
Shrink tubing for threaded ferrules

Clear heat-shrink tubes limit corrosion
Excludes moisture
Stress-relief for cable jacket and ferrule-to-stranding
connection
Part No.
P6001593P
P6001982P
P6002069P
Lengths
5"
7"
9"
Anderson die-less VERSA-CRIMP compression tools require no dies and are capable of making these crimped connections.
If using another crimp tool brand, contact that manufacturer for Burndy die equivalents.

Page 3020
March 2013
Typical Application
Threaded-terminal adapters for pressure-type

grounding-clamp terminals
Simply retrofit bolt-on adapters to convert clamps with
pressure-type terminals to accept 58-11 UNC threaded
ferrules
Typical Application
Catalog Number
C6001584
eyebolt style,
includes shakeproof washer
and nut
C6001700
includes steel retainer
straps for cable
C6001584
C6001700
Clamp Applications
C Type, Snap-On Flat-Face
All-Angle Clamps
Storage Bag for Temporary Grounding Clamps-and-Cable Sets

Easy-to-see, bright-yellow protective bag
Made of double vinyl-laminated open-weave nylon
cloth
Lightweight and durable with nylon stitching
throughout
Full-separating closure constructed with heavy-duty
snaps
Heavy webbing handles
18" L x 12" W x 15" D
Catalog No.
T6000865
Description
Grounding Storage Bag
Weight
3 lb.
Support Studs
G3626
G3627

Can be installed on most Ground Clamps
Replaces restraining strap immediately below terminal
Serves as a mechanical parking stand for a second
clamp
Helps prevent "parked" clamp from making contact
with conductor or ground
Particularly beneficial in three-phase grounding
applications
Catalog No.
G3626
G3627
Description
Stud for Rear Mount
Stud for Side Mount
Size of Stud
716" x 212"
716" x 3"
Weight
lb./.2 kg.
34 lb./.3 kg.
12
Dielectric Compound No. 7

Dielectric Compound No. 7, a silicone base material, is
made for use with load break disconnects and other
electrical connecting and terminating devices.
Cat. No. C4170287..................................... 2 oz. Tube

March 2013
Page 3021
Conversion Terminals
Cable Splice
for cables with plain-plug ferrules
Use for splicing grounding cable when extensions are
required
Thumb screw makes attachment easy
T6000252
Splice fits #2 through 4/0 grounding

cable with plain ferrules
Catalog No.
T6000252
Description
Grounding Cable Splice
Weight
112 lb./0.7 kg.
Terminal Blocks, 4-Way

G47541
for four
plain plug ferrules
for cables with plain-plug ferrules

and threaded ferrules
Attach ground leads from grounding clamps to a
common ground
Accommodates 4/0 grounding cables
Catalog No.
Weight
Description
G47541
4-Way Terminal Blocks for Plain Plug Ferrules 2 lb./0.9 kg.
T6001964 4-Way Terminal Blocks for Threaded Ferrules 1 lb./0.45 kg.
T6001964
for four 58-11 UNC
threaded ferrules
Cluster Support, 1-terminal type

Hangs grounding sets on the pole to facilitate lifting
clampsone at a time to the conductors
Accepts plain ferrules on #2 to 4/0 grounding cable
Copper bar length is 11"
Catalog No.
C6000152
Description
C6000152
Weight
912 lb./4.3 kg.
T6001549
for poles only
Cluster Bars
for wood, steel and concrete poles and
tower angles
Compact 5" aluminum-alloy bar (58" dia.) accepts
C-type or duckbill clamps
For phase-to-phase grounding technique
Adjustable wheel binder and 36" chain for pole
applications
Hook style for attachment to tower angles
Catalog No.
T6001549
T6001737
Description
Pole-Mount Grounding Cluster Bar
Tower-Mount Grounding Cluster Bar
Weight
712 lb./4.09 kg.
9 lb./4.09 kg.
T6001549
T6001737
(For tower angles only)

Page 3022
March 2013
Storage Reel for Grounding Cable
Catalog No.
C4176086
Description
Portable Cable Reel
Reel Capacity
225 ft.
185 ft.
145 ft.
100 ft.
Weight
18 lb./8 kg.
Temporary Ground Rod

Hole in outer flange for cable to feed through
Rewind handle has galvanized-pipe extension for
temporarily parking clamps
Portable reel quickly pays-out/takes-up,
Helps keep ground sets clean and neat, ready for use
Handles are comfortable, turned aluminum
Lightweight unit can be carried to remote sites
Tubular-steel frame can be U-bolted to deck of truck
Galvanized drum has ribbed flanges to resist flexing
and beaded rims to eliminate sharp edges
Reel is for storage only
Cable and clamps should be removed completely from
reel before use
Failure to do so could result in a dangerous voltage
drop and violent mechanical reactions
A label on the unit gives this warning

Screw Ground Rod provides a temporary ground
For when a system ground is not available
When installed, 6' spiraled ground rod develops less
resistance than straight ground rods
Actual effectiveness depends upon soil properties
Reusable Ground Rod is copper-clad steel
Helix (spiral) and handle are bronze
For truck-grounding applications, see kit below
Catalog No.
G3370
Description
Screw Ground Rod
Weight
734 lb./3.5 kg.
Truck Grounding Set

Provides means to drain off capacitance or static
charges
For winch trucks and aerial devices
Flat -face clamp is for secure attachment to the truck
bed at an area cleaned for electrical contact
C-type clamp is for secure attachment to ground rod
This grounding method should not be considered
adequate protection to personnel against conductor
contact
For truck-grounding with ball/socket-clamp, see page
3103
Truck Grounding Set
Catalog No. T6001971
(total weight 35 lb./15.75 kg.)
consists of:
Component
Qty.
Screw Ground Rod
1
Flat Face Ground Clamp
1
C-Type Ground Clamp
1
#2 Copper Grounding Cable 50 ft.
*Shrouded Alum. Ferrules
2
Storage Reel
1
Description
Cat. No. G3370, see above
Cat. No. T6001798, see page 3010
Cat. No. C6001754, see page 3004
Cat. No. S6116, see page 3018
Cat. No. C6002618, see page 3019
Cat. No. C4176086, see above
*Threaded ferrules are factory-installed on ends of cable.

March 2013
Page 3023
Cable Size
#2
1/0
2/0
4/0
Truck Safety Barricade
T3060006
Catalog No.
T3060006
Description
Truck Safety Barricade
Weight
21 lb./9.5 kg.
Grounding Simulator Kit

Keeps workers and onlookers away from truck when it

is being used in proximity to energized conductors
Six rods, made of bright orange Epoxirod, provide
a 6-foot air space around the entire perimeter of the
truck
Safety barricade also includes six pieces of 3-inch long
steel tubing (to be welded to truck by the customer)
Tubing holds barricade rods, 150 feet of yellow rope
and a canvas storage bag
Entire kit requires less storage than traffic cones and
can be quickly installed and removed at each job site
Demonstrates principles for temporary grounding

practices
Portable instructional aid provides working model of
three-phase system circuit
Powered by a step-down transformer
Plugs into a 110-volt 60-cycle household source
Special light/buzzer unit simulates lineworker in
maintenance on de-energized line
Insulated wires with alligator clip at each end serve as
grounding cable and clamp sets (10 included)
Miniature grounding cluster bar is included for pole
mounting
Modular design quickly sets up and takes down for

storage in rugged transport case.
Operation
Durable & Accurate
Durable, aluminum pipe poles
Wood crossarms
Electrically correct, aluminum poles effect the
conductivity which should be assumed for actual poles
Leads from the poles and neutral connect to ground
side on source (transformer)
To quickly test any proposed configuration, depress

transformer foot switch to energize a fault on the
system
If the light glows and the buzzer sounds on the
worker, this indicates the grounding system in place
fails to provide protection
If no such signals occur, the scheme of grounding
connections does create a protective zone of equalized
potential at the worksite
Ordering Information
Catalog No.
C6001950
Description
Weight
Grounding Simulator Kit 23 lb. / 10.5 kg.

Page 3024
March 2013
Standard (Orange) Equi-Mat

Personal Protective Ground Grid
Complies with OSHA 1910.269 for equipotential requirements near vehicles,
underground gear, overhead switches and in substations
Meets ASTM F2715 Standard
Portable, lightweight, high performance
An easy way to help establish an equipotential zone for a lineworker

For standing on during various energized and de-energized work practices
Properly applied, it accomplishes compliance with Occupational Safety and
Health Administration (OSHA) 1910.269:
o Equipotential Zone. Temporary protective grounds SHALL be placed
at such locations and arranged in such a manner as to prevent each
employee from being exposed to hazardous differences in electrical
potential.
Can be taken anywhere needed, is simple to use, maintain and store
Consists of a high-ampacity tinned-copper-braid cable sewn in a grid pattern
onto a vinyl/polyester fabric
Cable terminals permit connecting mat's grid in series with an electrical
ground and subject system component or vehicle
Simply rinsing with water comprises all the care the mat requires
Mat may be folded and stored in a tool bag to help keep it clean and
protected
Complete instructions are included with each unit
...continued on the next page...
Basic Equi-Mat Personal Protective Ground Grid

Each Basic Unit includes a Long Ball Stud and illustrated
instructions.
Size
Catalog No.
Single 14" Perimeter Braid
24" x 24"
PSC6003080* (Bucket)
58" x 58"
C6002850
58" x 120"
C6002851
120" x 120"
C6002852
Weight
5 lb. / 2.3 kg.

8 lb. / 3.6 kg.
13 lb. / 5.9 kg.
20 lb. / 9.1 kg.
*For use in bottom of personnel bucket of lift truck.
Pre-Packaged Kits
Each Pre-Packaged Kit includes Ground Grid (size below
with Long Ball Stud and illustrated instructions) plus
Ground Set T6002841 and Storage Bag C4170147.
Kit
Catalog No.
C6002989
C6002990
C6002991
Equi-Mat Personal Protective Ground Grid

Size
58" x 58"
58" x 120"
120" x 120"
Weight
per Kit
19 lb. / 8.6 kg.
27 lb. / 12.2 kg.
30 lb. / 13.6 kg.
Accessory Items
Long Ball Stud T6002364

included with each Basic Equi-Mat Personal
Protective Ground Grid (Catalog page 3013)
Ground Set T6002841 included with Kits only
Consists of 6 ft. long #2 cable with ferrules applied,
Ball Socket clamp (C6002100)
and C-Type clamp (T6000465)
Storage Bag
C4170147
included with Kits only
Catalog pages 2512-13

March 2013
Page 3025
Standard (Orange) Equi-Mat

Complies with OSHA 1910.269
For equipotential requirements near vehicles,
underground gear, overhead switches and in substations
Applications
Padmounted Transformers and Switches

Protects workers operating and maintaining padmounted
transformers and switchgear
Proper use of EQUI-MAT Personal Protective Ground Grid
in these applications creates an equipotential zone
This is the same as a cluster bar (chain binder) does in

overhead grounding practices
Bottom of Personnel Bucket on Lift Truck

Use only 24" x 24" Catalog No. PSC6003080
Mechanical Equipment (Vehicles, etc.) Grounding
Provides compliance with OSHA 1910.269

Protects workers around mechanical equipment which
could become energized, such as utility vehicles and
portable generators
For proper application, EQUI-MAT Personal Protective
Ground Grids are attached to the vehicle (for example)
at locations where workers could contact the vehicle
This extends the equipotential area around the vehicle
Simple to join multiples for larger areas
Cascading (or joining together) two or more mats is

easy
Connecting tab and hardware furnished with each mat
Overhead Distribution and Transmission Switches
EQUI-MAT Personal Protective Ground Grid can help

eliminate step and touch potential
Connect it to the handle of an overhead switch and stand
on it when opening or closing the switch
Line Apparatus Work
Similar uses for installing, maintaining or operating

regulators, reclosers, capacitor banks
Suspect Substation Grids
If station ground mat integrity is questionable, apply the

EQUI-MAT Personal Protective Ground Grid
Connected in series, the conductive grids become one
For larger area, place lug connector tabs of two
adjacent mats on the supplied bolt or threaded shank
of a ball stud and secure with supplied washer and nut
(Left) To join mats, conductive

grids simply connect at tabs
with bolt, washer and nut
included with each mat. Tabs
have shrink tube for stress
relief. (Right) Ball stud can
join mats and connect to
ground set clamps.
Long ball stud accepts various grounding clamps as shown
below and at right: Ball/Socket, C Type and Duckbill.

Page 3026
March 2013
Slip-Resistant (Black) Equi-Mat

Complies with OSHA 1910.269 for equipotential requirements near vehicles, underground gear, overhead switches
and in substations
Meets ASTM F2715 Standard
An easy way to help establish an equipotential zone
for a lineworker
For standing on during various energized and deenergized work practices
Properly applied, it accomplishes compliance with
Occupational Safety and Health Administration (OSHA)
1910.269:
o Equipotential Zone. Temporary protective grounds
SHALL be placed at such locations and arranged in
such a manner as to prevent each employee from
being exposed to hazardous differences in electrical
potential.
Can be taken anywhere needed, is simple to use,
maintain and store
Consists of a high-ampacity tinned-copper-braid cable
sewn in a grid pattern onto a vinyl/polyester fabric
Cable terminals permit connecting mat's grid in
series with an electrical ground and subject system
component or vehicle
Simply rinsing with water comprises all the care the
mat requires
Mat may be folded and stored in a tool bag to help
keep it clean and protected
Complete instructions are included with each unit
Slip-Resistant material
For rain, snow and ice conditions

Napped surface offers superior footing
For dry conditions, consider the Standard (Orange)
EQUI-MAT Personal Protective Ground Grid, available
in the same sizes and kits
...continued on the next page...
Slip-Resistant Equi-Mat Personal Protective Ground Grid

Each Unit includes Ground Grid, Long Ball Stud and
illustrated instructions
Catalog No.
Single 14" Perimeter Braid
PSC6003345
PSC6003346
PSC6003347
Size
58" x 58"
58" x 120"
120" x 120"
Weight
8 lb. / 3.6 kg.

13 lb. / 5.9 kg.
20 lb. / 9.1 kg.
Pre-Packaged Slip-Resistant Equi-Mat Kits

Each Kit includes Ground Grid (size below with Long Ball
Stud and illustrated instructions) plus
Ground Set T6002841 and Storage Bag C4170147
Kit
Catalog No.
PSC6003348
PSC6003349
PSC6003350
Equi-Mat Personal Protective Ground Grid

Weight
per Kit
Size
19 lb. / 8.6 kg.
58" x 58"
27 lb. / 12.2 kg.
58" x 120"
30 lb. / 13.6 kg.
120" x 120"
Accessories
Long Ball Stud T6002364
included with each Basic Equi-Mat Personal
Protective Ground Grid (Catalog page 3013)
Ground Set T6002841 included with Kits only
Consists of 6 ft. long #2 cable with ferrules applied,
Ball Socket clamp (C6002100)
and C-Type clamp (T6000465)
Storage Bag C4170147

included with Kits only
Catalog pages 2512-13

March 2013
Page 3027
Portable, lightweight, high performance
Slip-Resistant (Black) Equi-Mat

Complies with OSHA 1910.269 for equipotential requirements near vehicles, underground gear, overhead switches
and in substations
Padmounted Transformers and Switches

Protects workers operating and maintaining padmounted transformers and switchgear
Proper use of EQUI-MAT Personal Protective Ground
Grid in these applications creates an equipotential
zone
This is the same as a cluster bar (chain binder) does in
overhead grounding practices
Mechanical Equipment (Vehicles, etc.) Grounding
Provides compliance with OSHA 1910.269

Protects workers around mechanical equipment which
could become energized, such as utility vehicles and
portable generators
For proper application, EQUI-MAT Personal Protective
Ground Grids are attached to the vehicle (for example)
at locations where workers could contact the vehicle
This extends the equipotential area around the vehicle
Overhead Distribution and Transmission Switches

EQUI-MAT Personal Protective Ground Grid can help
eliminate step and touch potential
Connect it to the handle of an overhead switch and
stand on it when opening or closing the switch
Line Apparatus Work
Similar uses for installing, maintaining or operating

regulators, reclosers, capacitor banks
Suspect Substation Grids
If station ground mat integrity is questionable, apply

the EQUI-MAT Personal Protective Ground Grid
Simple to join multiples for larger areas
Cascading (or joining together) two or more mats is

easy
Connecting tab and hardware furnished with each mat
Connected in series, the conductive grids become one

For larger area, place lug connector tabs of two adjacent mats on the supplied bolt or threaded shank of a
ball stud and secure with supplied washer and nut
(Left) To join mats, conductive

grids simply connect at tabs
with bolt, washer and nut
included with each mat. Tabs
have shrink tube for stress
relief. (Right) Ball stud can
join mats and connect to
ground set clamps.
Long ball stud accepts various grounding clamps as shown
below and at right: Ball/Socket, C Type and Duckbill.

Page 3028
March 2013
Rotating Ground Adapters for Reels

Tested andMeets ASTM F 855 Standard
Applications
Provide system protection while conductor is pulled
from reels for stringing operations By design, the
system adds conductor grounding but does not replace
other grounding practices
This includes items such as Equi-Mat personal
protective ground grids (Chance Catalog Section 3000)
System serves as intended path to ground for static
discharge and accidental energizing from downed
lines, equipment contact, adjacent conductors and
lightning
Rotating Ground Adapter slides on reel mandrel and
three locking bolts secure it
Outer collar contact connects to the end of the
conductor from inside the reel
Adapters inner collar contact connects to a permanent
or screw-in ground rod (not included, see Chance
Catalog Section 3000)
< Bronze
Vise-type connectors
Ball-stud connectors>
PST6003438
Single Reel Grounding Set
GR253X
GR43BS2
Rotating Ground Adapters
Rotating Ground Adapters for Reels

Ordering Information
Catalog No.
Rotating Grounding Adapters
GR253X
GR43BS2
ASTM Grade:
Fault Rating
Pipe Dia.
Maximum
Connector
Range
Weight
ASTM Grade 1:
14kA @ 15 cycles
10kA @30 cycles
ASTM Grade 5:
43kA @15 cycles
30kA @30 cycles
3-3/16"
Bronze Vise Type
3 Sol. to 4/0 Str.
2-11/16"
Two 1"-diameter
Ball Studs
See Ball Stud

Clamp in Chance
Cat. Section 3000
Single Reel Grounding Set

PST6003438
Connector
Type
Assembled Bill of Materials

Grade 3:
27kA @15 cycles
20kA @30 cycles
(Ratings for this set are
limited to those for the
2/0 grounding cable.)
2-11/16"
4 ea. C6001754 C-type ground clamps,

2 ea. T6002320 ball stud ground clamps,
1 ea. GR43BS2 rotating ground adapter,
6 ea. Ferrules (aluminum),
6 ea. Shrink tubes,
63 ft. S6118 yellow neoprene 2/0 cable
(1 @ 50 ft., 1 @ 10 ft., 1 @ 3 ft.)
9.8 lb. (4.4 kg.)
12.75 lb.
(5.8 kg.)
53.75 lb.
(24.4 kg.)

March 2013
Page 3029
Installation
NOTES
Page 3030
March 2013
NOTES

March 2013
Page 3031
210 N. Allen St. Centralia, MO 65240 (573) 682-5521
NOTICE: For the latest revision of our Catalog and Literature, click here or visit our web site: www.hubbellpowersystems.com
NOTE: Hubbell has a policy of continuous product improvement. We reserve the right to change design and
specifications without notice. Copyright 2013 Hubbell Incorporated
NEVER COMPROMISE
www.hubbellpowersystems.com
Catalog
3000
March
2013
MARCH 2013
Page 3032

Grounding Equipment: Catalog 3000 March 2013

Uploaded by

Copyright:

Available Formats

Grounding Equipment: Catalog 3000 March 2013

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Grounding Equipment: Catalog 3000 March 2013

Uploaded by

Copyright:

Available Formats

What are the recommended grounding practices for de-energized distribution lines?

What are the recommended grounding practices for de-energized distribution lines?

What are some reasons for temporary grounding?

What are some reasons for temporary grounding?

G rou n d i n g Eq u i p m ent 3 0 00

Phone: 573-682-5521 Email: hpsliterature@hubbell.com Web: hubbellpowersystems.com

Temporary Grounding Equipment

There are many reasons for temporary grounding to

Vital Procedure Recommendations

Step Two: Cleaning

Step Three: Connecting

Chance insulated Grip-All clampsticks are the proper

On de-energized distribution lines, Chance recommends Double-Point grounding

Short Circuit PropertiesA

Phone: 573-682-5521 Email: hpsliterature@hubbell.com Web: hubbellpowersystems.com

Temporary grounding practices should be reviewed on

Selecting grounding clamps and cable

How to order a Grounding Set

cable ferrule type (either plain or threaded) to match

On-site handlingApplication clearances and fit (for

Several training aids available on request

Phone: 573-682-5521 Email: hpsliterature@hubbell.com Web: hubbellpowersystems.com

C-Type Grounding Clamps

Main Line Range - Min.

1000 kcmil Cu.

Phone: 573-682-5521 Email: hpsliterature@hubbell.com Web: hubbellpowersystems.com

Fault Current - 15 Cycles (amps)

Continuous Current (amps)

Fault Current - 30 Cycles (amps)

Main Line Range - Max.

2" O.D. Bus

2" O.D. Bus

2" O.D. Bus

2" O.D. Bus

2" O.D. Bus

2" O.D. Bus

2" O.D. Bus

2" O.D. Bus

Main Line Range - Min.

Jumper Range - Max.

Jumper Range - Min.

134 lb./0.8kg. 134 lb./0.8kg. 134 lb./0.8kg.

Phone: 573-682-5521 Email: hpsliterature@hubbell.com Web: hubbellpowersystems.com

C-Type Grounding Clamps

C-Type Grounding Clamps

Bus-Bar Grounding Clamps:

Fault Current - 30 Cycles (AMPS)

2-12 O.D. Bus

2-12 O.D. Bus

Main Line Range - Min.

4/0 Str. Cu.

3-12 O.D. Bus

Jumper Range - Max.

4/0 Grd. Cable

4/0 Grd. Cable

4/0 Grd. Cable

4/0 Grd. Cable

4/0 Grd. Cable

Jumper Range - Min.

Chance insulated Grip-All clampsticks are the proper

On de-energized distribution lines, Chance recommends Double-Point grounding

Temporary grounding practices should be reviewed on

Several training aids available on request