1049D CERABOND 2000 Rev (1409)

Sheet No.
: 1049D-K
Issued Date : Sep. 2014
CERABOND 2000
(CB 2000)
PRODUCT DESCRIPTION
CERABOND 2000 is a combination of heat resistant alloy and heat resistant silicate solution producing an
inorganic rust preventive coat mechanically adhered to the steel and giving an effective and long-term
protection against corrosion without suffering from blistering and loss of adhesion.
It is compatible with organic over coatings as well as with inorganic over coatings.
CERABOND 2000 is extremely resistant to heat (up to 800) and secondary surface preparation cost can be
decreased. It has excellent welding and cutting properties and presents no health hazard to the welder.
CERABOND 2000 has been approved by Lloyds Register of Shipping as a shop primer which is suitable for
welding.
PRODUCT INFORMATION
Type
Recommended Use
Type of binder
Mixing Ratio
Color
Flash Point
Solids by Volume
VOC
Coverage(Theoretical)
Wet Film Thickness
Dry Film Thickness
Drying Time
(at D.F.T. 15)
Painting Interval
(at D.F.T. 15)
Pot Life
Thinner
Method of Application
Condition of Application
Preferable Subsequent Coats

Packaging
Inorganic zinc silicate shop primer

As a shop primer for primary protection of blast-cleaned steel , as a
general purpose rust-preventing primer for organic and inorganic
over-coating, and also as a heat resistant paint.
Ethyl silicate
Paste : Base = 42 : 58 (by volume)
Green, Grey, Light Grey, Brown, Grey S
Paste : 22.5 , Base : 13.5
30 2 %
632 g/
20.00 / [0.050 /] at D.F.T 15
33 - 100
10 - 30
5
10
20
30
Temperature
Surface Dry
3 min.
3 min.
2 min.
2 min.
Hard Dry
6 min.
5 min.
4 min.
3 min.
Min. Organic
14 days.
10 days.
7 days.
7 days.
Inorganic
16 hrs.
8 hrs.
4 hrs.
4 hrs.
Maximum
180 days
180 days
180 days
180 days
36 hrs.
30 hrs.
24 hrs.
15 hrs.
INORGANIC SHOP PRIMER THINNER series
Airless spray, Brush, Roller
Temperature
: -5 ~ 40
Humidity
: Maximum 90 % R.H.
For Airless spray ;
Tip No.
: GRACO 617 - 923
Paint output pressure : 3.8 8.9 MPa
Viscosity
: 9 - 11 sec.(Ford Cup No.4)
Thinning
: 5 - 35 % by volume
Most our products or the equivalents.
However, when oleoresins or vinyl paints are applied, please consult us.
Two pack product
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Sheet No. : 1049D-K

Issued Date : Sep. 2014
TECHNICAL DATA (at 15)

Temp ()
-5
10
15
20
25
30
35
40
5m
4m
3m
3m
3m
2m
2m
2m
1m
1m
Min.(Organic)
14D
14D
14D
10D
8D
7D
7D
7D
6D
6D
Min.(Inorganic)
20H
18H
16H
8H
5H
4H
4H
4H
3H
3H
Max.
6M
6M
6M
6M
6M
6M
6M
6M
6M
6M
8m
7m
6m
5m
4.5m
4m
3.5m
3m
2.5m
2m
Body
Touch-up
Dry to Touch-up
20H
18H
16H
8H
5H
4H
4H
4H
3H
3H
Pot life
48H
42H
36H
30H
26H
24H
18H
15H
12H
8H
Shelf life (M)
6M
6M
6M
6M
6M
6M
6M
6M
6M
6M
Item
Set to touch
Dry to recoat
Dry to hard
Dry to immerse
Max. heat resistance
Continuous: 400
/ Non
-continuous:
800
Abbreviation ; Y : Year, M : Month, D : Day,

H : Hour, m : Minute
*Drying time (below 10degC) is used only as a guide with pre-heating and after-heating equipment.
RECOMMENDABLE SURFACE PREPARATION

All surfaces to be free from various contaminants (oil, grease, dust, spray dust and etc.) and keep surfaces dry.
Kindly consult CSP sales office for specific information.
SAFETY PRECAUTIONS
In order to ensure safe use of our product, please be sure to follow the safety precautions indicated on the SDS and the paint container. If
you need further explanation, do not hesitate to consult our personnel or our local distributors before buying, opening, using, or disposing
the product. Since product contains flammable materials, keep away from sparks and open flame. No smoking should be permitted in the
area on painting.
Wear an appropriate protector (eye and face protection, protective clothing, barrier creams, etc) when mixing, applying, or drying the
paint. If products come into contact with the skin, wash thoroughly with warm water and soap or suitable cleaner. If the eyes is
contaminated, irrigate with water and seek medical advice immediately.
DISCLAIMER
The information, including data, specifications, directions and recommendations, contained in this Data Sheet describes the experiment results under
controlled or specially defined conditions and we do not guarantee that the Products, when used under the actual conditions of any intended use, will
produce the same results. The performance of the Products in their actual use is affected by various factors, and the User must judge whether the Products
are suitable for specific uses. We do not guarantee the performance of the Products under any specific operation environment other than the performance of
the Products under the conditions described in this Data Sheet.
The content of this Data Sheet, which is intended for facilitation of the Users understanding and convenience of use of the Products, is subject to change at
any time without prior notice. We use our best efforts to reflect the latest and most accurate information in this Data Sheet, but we will not bear any liability
whatsoever relating thereto. The User must confirm that the Data Sheet is the latest version prior to using the Products.
We do not guarantee the performance or safety of the Products when used for a purpose or use other than what is described herein. Nor will we be liable for
any explanation or guarantee provided by any distributor or sales agent with respect to the Products, other than what is described in this Data Sheet.
Furthermore, each of the Products described herein is composed of various chemical substances, some of which may contain toxic and/or harmful
ingredients and may cause harmful results as a result of misuse or overuse of the Products. For specific causes of risk, conditions of use, harmfulness, etc.
of each of the Products, please carefully read, prior to use of the Products, the MSDS (Material Safety Data Sheet) inserted in each of the Products. We will
not be liable for any accident that may be caused in violation thereof.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.

1049D CERABOND 2000 Rev (1409)

Uploaded by

Copyright:

Available Formats

1049D CERABOND 2000 Rev (1409)

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1049D CERABOND 2000 Rev (1409)

Uploaded by

Copyright:

Available Formats

Sheet No.

Preferable Subsequent Coats

Inorganic zinc silicate shop primer

Sheet No. : 1049D-K

TECHNICAL DATA (at 15)

Shelf life (M)

Max. heat resistance

Abbreviation ; Y : Year, M : Month, D : Day,

RECOMMENDABLE SURFACE PREPARATION

You might also like