Contouch 204 TPI en 2014-02-06 PDF

GAMMA instabus
Technical Product-Information
February 2014
Room Controller Contouch UP 204 5WG1 204-2AB_1
Accessory:
Contouch Flash-Kit 5WG1 204-8AB01
Product and Function Description texts and symbols on the display in 4 different designs.
Text and alarm messages can also be displayed. Alarm
messages are specially highlighted by an acoustic signal
and the LED display. The touchscreen can be used to
select from up to 6 languages for the display of texts and
messages.
The room temperature controller integrated in Contouch

is specially designed for use in rooms which are heated
and / or cooled where the manner of room temperature
control depends on up to four room operating modes
(comfort mode, pre-comfort mode, energy-saving mode,
and protection mode). As required, a parameter can be
set so that the controller does not consider all four oper-
ating modes, but rather only three (comfort mode, ener-
gy-saving mode and protection mode) or only two (com-
fort mode and protection mode). The room temperature
controller can be used as a two-point controller (thermo-
stat) or a continuous controller (P or PI-controller).
The Contouch room controller, hereinafter referred to as
Contouch, combines the functions of a graphic display The current room operating modes, automatic or manual
with up to 18 room operating functions, an individual operation, the interior or exterior temperature, the
room temperature controller with setpoint indication and setpoint temperature, an open heating and cooling valve,
operating mode setting, a temperature sensor and a fan- melting point operation or open windows are clearly
coil unit control panel in one bus node. shown on the display in a self-explanatory manner.
Contouch is available in the following colours variations:
By means of a special display page, the room tempera-
titanium white: 5WG1 204-2AB11 ture control parameters can be set using the
carbon metallic 5WG1 204-2AB21 touchscreen. There the room operating mode can be se-
aluminium metallic 5WG1 204-2AB31 lected directly on site. The manual mode is activated in
piano black 5WG1 204-2AB51 this way. In manual mode, every room operating mode
can be permanently activated and not changed by a bus
telegram.
The following accessories are available for the Contouch
room controller: The controller offers the option of extending the duration
of the Comfort operating mode. For this purpose, the
Contouch Flash-Kit 5WG1 204-8AB01 "Comfort mode extension" button is pressed on this spe-
cial touchscreen operator page and the length of the
This flash kit consists of a removable data carrier, a mi- Comfort mode extension set by a rotary control.
cro SDHC card with two adapters, a micro SD Adapter
and a USB micro SD reader. The setpoint temperature is set directly in C/F on the
display page for room temperature control based on the
room operating mode Comfort mode or as a relative val-
ue, shifting from the base setpoint in K. The rotary control
The basis of the equipment is a high-quality 320 x 240 of the controller can be used to shift the specified setpoint
pixel colour display 2.8" with touchscreen and rotary to a higher or lower value, whereby the range of the offset
control. This is equipped with a rotary/push-button func- can be adjusted.
tion.
The automatic mode setting can also be selected directly
Contouch is operated by the touchscreen and the rotary on the Contouch. The the controller receives its operat-
control. The buttons shown on the display can be used ing mode directly by telegram from the bus or via the in-
for switching and dimming lights, for regulating sun pro- ternal time switch program.
tection or for the retrieval and storage of scenes. The
functions and conditions can be shown graphically with
Siemens AG Up 204, page 1 / 9 Technical Manual

Infrastructure & Cities Sector, Building Technologies
Control Products and Systems Siemens AG 2014 Update: http://www.siemens.com/gamma
P. O. Box 10 09 53, D-93009 Regensburg Subject to change without further notice
2.12.1.14
GAMMA instabus
Technical Product - Information
February 2014
Accessory:
In rooms which are heated and / or cooled by a fan coil The bus coupler contained in the scope of supply make
unit, the Contouch can be used as a control panel for the it possible to connect the Contouch to the bus line by
ventilator control. means of its user interface.
The current fan speed is shown on the display. The telegrams received through the bus line are
In manual operation, the speed level of the fan can be processed by the bus coupler and forwarded to
set by the rotary control on the Contouch. Contouch. In the opposite direction, signals coming from
At speed level "0", the fan switches off and a possibly Contouch are converted into telegrams and sent through
open valve closes, i.e. the room is then neither heated the bus.
nor cooled. If the setpoint for heat protection is then ex- The bus coupler is connected directly to the bus, where
ceeded or the setpoint for frost protection fallen short of, it monitors this constantly and is therefore always in-
automatic mode becomes active in the case of a contin- formed as to whether the bus line is free or busy with
uous controller and the fan is switched to the highest fan telegrams. If an event occurs and the bus line is free, the
speed if a two-point controller is used. The controller bus coupler begins sending immediately. Otherwise the
heats or cools until reaching the setpoint of the previous- sending request is stored until the bus line is free.
ly set operating mode.
With option "A", the Contouch rotary control is used to Note: Contouch can only be used together with the sup-
set the fan control to automatic mode. Then the speed is plied bus coupler.
specified by the control system.
The display lighting switches on when Contouch is oper- Bus Coupler Technical Data
ated. The lighting switches off after a certain time period,
which must be configured. The device is in standby Power supply
mode. Input voltage
Bus: DC 24V (DC 21...30 V), 10 mA
Time programs with weekly switching plans can be con- Booster voltage: DC 24 V (DC 1230 V), 50 mA, from
figured for the 18 room operating functions and for set- external SELV power supply
ting the room operating mode of the controller. Up to 16 Recommended power supplies:
switching points can be set for each time switch pro-
gram. The time switch programs for setting the room op- LOGO! Power 24 V / 1,3 A, (class 2),
erating mode are activated in automatic mode. Rated input voltage AC 100240 V wide range,
Input voltage range AC 85264 V,
Contouch offers a cleaning function. If this has been ac- Constant current supply DC 24 V / 1,3 A,
tivated by the touchscreen, then the device is blocked for Rated output voltage: DC 24 V,
servicing for a specific time period, which must be con- Width: 3 SU
figured. The device, in particular the touchscreen, can be
cleaned without triggering unwanted functions. LOGO! Power 24 V / 2,5 A,
Rated input voltage AC 100240 V wide range,
The internal Contouch signal generator provides the Input voltage range AC 85264 V,
acoustic display of alarm messages and can be used as Constant current supply DC 24 V / 2,5 A,
a response when a button is activated. Rated output voltage: DC 24 V,
Width: 4 SU
You use the ETS3 (Version 3 and higher) to select the
application program, to allocate specific parameters and LOGO! Power 24 V / 4 A,
addresses and to transfer these into the Contouch UP Rated input voltage AC 100240 V wide range,
204 room controller. Input voltage range AC 85264 V,
Constant current supply DC 24 V / 4 A,
Rated output voltage: DC 24 V,
Width: 5 SU
Application program
Output voltage and current on Contouch
Contouch room controller: DC 3.3 V, > 150 mA
0705 Contouch room controller 970001
Technical Manual UP 204, page 2 / 9 Siemens AG

Update: http://www.siemens.com/gamma Siemens AG 2014 Control Products and Systems
Subject to change without further notice P. O. Box 10 09 53, D-93009 Regensburg
2.12.1.14
GAMMA instabus
February 2014
Accessories:
Operating elements Construction, location and functioning of the

1 learning key: display and operating elements of the bus cou-
To switch between normal and addressing modes pler
Indicating elements
1 red LED:
To display normal and addressing modes A2
A3
A1
Connections
Bus line: Bus terminal (black/red) , screwless A4 A4
0.6 ... 0.8 mm solid
Power supply: Bus terminal (yellow-white), screwless A6 A5
0.6...0.8 mm , solid A7
6-pole socket (AST) for connecting the Contouch
Mechanical specifications Figure 1: Location of the display and operating Elements

Casing plastic Bus couplers
Dimensions:
- Hole pitch: 72 x 72 mm A1 Red LED for indicating normal mode (LED Off) or
- mounting depth: 21 mm addressing mode (LED On); it goes out automati-
Weight: 58 g (with hanger) cally after transferring the physical address
Fire resistance: approx. 610 kJ A2 Key for switching between normal mode and ad-
Assembly: is fastened to the flush-mounting box dressing mode for transferring the physical ad-
dress
Electrical safety A3 Nameplate for entering the physical address
Degree of contamination (acording to IEC 60664-1): 2 A4 Holes for the centring spikes for fastening the
Degree of protection (according to EN 60529): IP 20 Contouch to the bus coupler
Protection class (according to IEC 61140): III A5 6-pin user interface (AST) for connecting the
Overvoltage category class (according to IEC 60664- Contouch
1): II A6 Slots for fastening the bus coupler to the installa-
Bus: Secure low voltage SELV 24V DC tion mounting box
A7 Threads for the fixing screw (for the additional
Auxiliary supply voltage SELV 24V DC
fastening of the Contouch, e.g. theft protection)
Device complies with EN 50491-3, EN 61558-2-6 and
EN 61558-2-16
Reliability
Failure rate: 136 fit at 40C
EMC criteria
fulfills EN 50491-5-1, EN 50491-5-2, EN 50491-5-3
Environmental specifications
Resistance to climate EN 50090-2-2
Ambient temperature in operation: - 5 ... + 45 C
Storage temperature: - 25 ... + 70 C
Relative humidity (non-condensing): 5% to 93%
Approval mark
KNX EIB
EC marking
to EMC directive (residential and functional building), low
voltage guideline
Siemens AG UP 204, page 3 / 9 Technical Manual

2.12.1.14
GAMMA instabus
February 2014
Accessory:
Technical data for the Room Controller Overvoltage category class (according to IEC 60664-
Contouch 1): II
Bus: Secure low voltage SELV 24V DC
Power supply Device complies with EN 50491-3, EN 61558-2-6 and
Input voltage from the bus coupler via 6-pin plug con- EN 61558-2-16
nector
3.3 V DC Reliability
Failure rate: 1198,7 fit at 40C
Operating elements
Rotary control with rotary / push-button function EMC criteria
Touch display with touch function fulfills EN EN 50491-5-1, EN 50491-5-2, EN 50491-5-3
Indicating elements Environmental specifications

320 x 240 Pixel colour display 2.8" with touchscreen, Resistance to climate EN 50090-2-2
18 bit colour depth, effectively used 16 bit colour depth Ambient temperature in operation: - 5 ... + 45 C
RGB LED under the colourless, transparent ring No direction sunlight
around the rotary control/push-button; serves as orien- Storage temperature: - 25 ... + 70 C
tation light to signal alarms and describe the start be- Relative humidity (non-condensing): 5% to 93%
haviour
Approval mark
Temperature measurement KNX EIB
Measuring range: 0 ... + 40 C
Resolution: 0.1 K EC marking
Accuracy in relation to the sensor temperature: according to EMC directive (residential and functional
1,5 K under reference conditions building), low voltage guideline
2.0 K under environmental condition and in the
measuring range
Connections
6-pin plug connector for attaching and connecting with
the bus coupler
Mechanical specifications
Casing plastic
Dimensions:
- (L x W x D): 116 x 86 x 14 mm (without rotary/push-
button and without plug connector guidance ),
- (L x W x D): 116 x 86 x 24 mm (with rotary/push-
- (L x W x D): 116 x 86 x 30 mm (with rotary/push-
Weight: 88 g
Fire resistance: approx. 2320 KJ
Mounting: The Contouch is attached to the bus cou-
pler and screwed to its support frame with a Phillips
screw M 2.5 x 5 (theft protection)
Electrical safety
Degree of contamination (according to IEC 60664-1):
2
Degree of protection (according to EN 60529): IP 20
Protection class (according to IEC 61140): III

2.12.1.14
GAMMA instabus
February 2014
Accessories:
Construction, location and functioning of the

display and operating elements of the
Contouch
B1 C1
C1 C2
C3
B2 C4
C5
B3
Figure 3: Rear view of the Contouch unit
C1 Spikes for centring the Contouch on the

Bus coupler
Figure 2: Location of the display and operating elements C2 6-pin plug connector as user interface to the
Front view of the Contouch unit Bus coupler
C3 Screw for fastening the Contouch to the support
frame of the bus coupler
B1 Touch display
B2 RGB LED C4 Insert for the micro SD card
B3 Rotary control with push-button function C5 Temperature sensor
Assembly, wiring and commissioning
Connection example
Bus coupler
6 Room controller:
Contouch
AST

2.12.1.14
GAMMA instabus
February 2014
Accessory:
Installation notes The bus terminal and supply terminal (terminal block)
(E1) consist of two parts (E1.1, E1.2), each with four
The system is used for fixed installation in dry internal terminal contacts. You must take care that both test
areas for the installation of flush-mounting boxes. sockets (E1.3) are not damaged, either with the bus
lead (accidental attempt to plug in) or with the screw-
driver (when trying to remove the terminal)..
V WARNING Insert the screwdriver carefully into the wire insertion
slot of the red/black or yellow/white part of the terminal
The system may only be installed and commissioned and remove the terminal from the bus coupler (Figure
by a licensed electrician. 5).
The device may not be inserted together in the same
socket with 230V equipment and/or 230V cables. Note
The relevant safety and accident prevention rules are Do not lever the terminals outwards from below! Risk of
to be obeyed. short-circuit
The system must not be opened.
When planning and installing electrical systems, the Attach bus terminal and supply terminal
relevant national directives, rules and regulations of
the country in question are to be obeyed. Plug the terminals into the guide grooves of the bus
coupler and push the terminals downwards to the end
stop.
Connecting the bus and supply terminals
The terminals (E1) are suitable for solid leads

D1 with a diameter of 0.6 ... 0.8 mm.
Remove insulation on the ends of the leads
(E1.4) and plug them into the terminal (E1) (red
D2 = +, black = -) or (yellow = +, white = -) (Fig. 6).
E1 E 1.4 E1
Figure 4: Connection of the bus and supply terminals

5 mm E 1.4
The connection to the bus line (D1) and to the booster Figure 6: Connection and disconnection of leads
voltage (D2) is achieved using screwless plug-in termi-
nals. If the bus line is connected with reverse polarity, then the
bus coupler is switched off by a protective device (re-
Remove bus terminal and supply terminal verse polarity protection). This also applies for the re-
quired booster voltage.
The bus terminal (D1) and the supply terminal (D2) are
located on the rear side of the bus coupler (Figure 4). Disconnection of the bus and supply lines
E1 Remove the terminal (E1) and pull out its lead

(E1.4) by turning it alternately backwards and
E1.3 forwards (Figure 6).
E1.1 E1.2
Figure 5: Terminals

2.12.1.14
GAMMA instabus
February 2014
Accessories:
Mounting
G1
A screw connection is used to install the bus coupler in
60 mm mounting boxes (see Fig. 7).
G2
F1 G3
F2
Figure 8: Mounting of the Contouch
F3 Starting up
- Fasten the bus coupler (F2) to the flash-mounting box

Figure 7: Assembly of the bus coupler (F1) and connect it to the bus line and the booster
voltage.
F1 Mounting box (60 mm in accordance with - Press the start-up button (A2): Start-up LED (A1) illu-
DIN 49073) minates
F2 Bus coupler - Use the ETS to load the physical address and the con-
F3 Bus coupler fixing screws figured application program
- Use the two centring spikes (C1) and the 6-pin plug
connector (C2) to attach Contouch to the bus coupler
and screw this onto the support frame (G1) with the
Note: fixing screw (G2) (Theft protection)
- Attach rotary/push-button (G3) to the Contouch
The bus coupler must be mounted in such a way that
the user interface (AST) is located at the bottom (see Along with the user interface, Contouch is equipped with
Fig. 1 or 7). Please ensure thereby that the Contouch to a removable data carrier (micro SDHS card). This flash
be attached to the AST is mounted in the correct posi- card contains various files (Firmware and defined con-
tion for operation. For a permanently secure contact figuration settings) for the start-up of Contouch, which
connection to the AST, it is urgently recommended to have been stored or generated by ETS plug-in. Thus,
lock the Contouch into place with the fixing screw. the removable data carrier is to be connected with the
commissioning PC for every start-up. The Contouch
flash kit, which is available as an accessory for the
Contouch room controller, offers both adapters (micro
SD Adapter and USB microSD reader) along with the
micro SDHC card. The two adapters can be used to in-
stall the removable data carrier into the SD card slot or
in the USB port of the commissioning PC. During start-
up with the Contouch plug-in, the "generate" command
is used to store the following files on the removable data
carrier:
RC-Programming-card.info
rc.bin (Firmware Contouch)
rcconfig.bin (Configuration Contouch)

2.12.1.14
GAMMA instabus
February 2014
Accessory:
The storage card is subsequently inserted into the care must be taken to ensure a low-vibration installa-
Contouch micro SD card slot. For this purpose, the tion site
Contouch is removed from the bus coupler, Fig. 8. This
occurs by removing the rotary/push-button (G3) and by Drafts from windows and doors must be avoided!
loosening the safety screw (G2). After insertion of the
micro SD card into the shaft (C4) on the Contouch (con-
tacts point toward the front of the Contouch) and its at-
tachment to the bus coupler, the Contouch is booted. In
the process, the current Firmware and the configuration
data are automatically loaded into the Contouch. The
storage card should be removed again after restarting
the Contouch (the main menu is displayed). This will
considerably shorten the start behaviour of the
Contouch. All changes have now been accepted and are
now permanently stored in the memory. After completion
of start-up, relock the Contouch to the bus coupler with
the fixing screw and plug the rotary/push-button (G3)
back into the Contouch.
Figure 9: Installation instructions for sensors and
Note: temperature controllers
If the micro SD card is changed without removing the
Contouch from the bus coupler, then the device must The device-side end of the installation tube must be
be restarted for the data transfer. sealed so that no drafts form in the tube which negative-
ly affect the measurements, see Fig. 10.
Micro SD and micro SDHC cards can be used as stor-
age media.
Dismounting
- Remove rotary/push-button (G3)

- Unscrew the fixing screw (G2).
- Remove Contouch from the bus coupler
- Remove the bus coupler from the flush-mounting box
Mounting site (see Fig. 9)
Observe the following notes when mounting the Figure 10: Sealing of the installation tube
Contouch room controller:
Controller mounting on the interior wall of the room to be

air-conditioned, opposite the heating source:
at a height of around 1.5 m in the occupied zone and
at least 50 cm away from the nearest wall.
not on exterior walls
not in niches or behind curtains
not above or near heat sources or shelves
not on walls, behind which heat sources such as a
fireplace are located
not in the radiation range of heat sources and lights
such as spot lamps
not in areas with direct sunlight

2.12.1.14
GAMMA instabus
February 2014
Accessories:
Dimensional drawing of the bus coupler
Dimensions in mm
72
23.5
72 21
Dimensional drawing of Contouch

14 10
Dimensions in mm 44
86
56,4
72
42
116
642 General notes
The operating manual is to be handed over to the
customer.
A defective device is to be sent back to the responsi-
ble sales office with a return shipping note.
If you have further questions concerning the product,
please contact our Technical Support:
' +49 (911) 895-7222
7 +49 (911) 895-7223
* support.automation@siemens.com
www.siemens.de/automation/support-request

2.12.1.14

Contouch 204 TPI en 2014-02-06 PDF

Uploaded by

Copyright:

Available Formats

Contouch 204 TPI en 2014-02-06 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Contouch 204 TPI en 2014-02-06 PDF

Uploaded by

Copyright:

Available Formats

GAMMA instabus

Room Controller Contouch UP 204 5WG1 204-2AB_1

The room temperature controller integrated in Contouch

Siemens AG Up 204, page 1 / 9 Technical Manual

Room Controller Contouch UP 204 5WG1 204-2AB_1

Technical Manual UP 204, page 2 / 9 Siemens AG

Room Controller Contouch UP 204 5WG1 204-2AB_1

Operating elements Construction, location and functioning of the

Mechanical specifications Figure 1: Location of the display and operating Elements

Siemens AG UP 204, page 3 / 9 Technical Manual

Room Controller Contouch UP 204 5WG1 204-2AB_1

Indicating elements Environmental specifications

Technical Manual UP 204, page 4 / 9 Siemens AG

Room Controller Contouch UP 204 5WG1 204-2AB_1

Construction, location and functioning of the

C1 Spikes for centring the Contouch on the

Assembly, wiring and commissioning

Siemens AG UP 204, page 5 / 9 Technical Manual

Room Controller Contouch UP 204 5WG1 204-2AB_1

Connecting the bus and supply terminals

The terminals (E1) are suitable for solid leads

Figure 4: Connection of the bus and supply terminals

E1 Remove the terminal (E1) and pull out its lead

Technical Manual UP 204, page 6 / 9 Siemens AG

Room Controller Contouch UP 204 5WG1 204-2AB_1

- Fasten the bus coupler (F2) to the flash-mounting box

Siemens AG UP 204, page 7 / 9 Technical Manual

Room Controller Contouch UP 204 5WG1 204-2AB_1

- Remove rotary/push-button (G3)

Mounting site (see Fig. 9)

Controller mounting on the interior wall of the room to be

Technical Manual UP 204, page 8 / 9 Siemens AG

Room Controller Contouch UP 204 5WG1 204-2AB_1

Dimensional drawing of the bus coupler

Dimensional drawing of Contouch

Siemens AG UP 204, page 9 / 9 Technical Manual

You might also like