Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 468 views

    Barnett Clutch

    Uploaded by

    thailan
    clutch

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Barnett Clutch

    Uploaded by

    thailan
    468 views2 pages
    clutch

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    clutch

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    468 views2 pages

    Barnett Clutch

    Uploaded by

    thailan
    clutch

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    BARNETT Scorpion

    Refer to Factory Service Manual for:


    All Safety Instructions

    Removal/ Installation Instructions

    Proper Tools and Pullers


    Installation Guide
    Torque and Lubrication Specifications
    608-30-10009
    2007-10 Big Twins & 2006-10 Dyna

    Removing The Existing Clutch


    Note:
    A hydraulic press is required to remove OEM clutch hub
    and install the Barnett Scorpion clutch hub!

    Barnett Tool and Engineering recommends changing primary


    lubricant after the first 500 miles and every 5,000 miles
    thereafter.

    1. To protect against accidental shock or start up. Disconnect


    both battery cables.
    Photo 1
    2. Remove primary drain plug at bottom of primary.

    3. Remove foot pegs (shifter lever) floorboard etc.


    Installing Your Scorpion Clutch
    1. Using a press install the Barnett Scorpion Clutch hub into
    4. Remove (5) five screws to remove inspection cover from
    the OEM clutch hub basket. Securely support the inner
    primary chain cover.
    bearing races during this process. Carefully bottom the
    Scorpion Clutch hub In the OEM basket. After pressing
    5. Remove (13) thirteen socket set screws with washers from
    the Barnett Scorpion hub, check the bearing for smooth
    primary cover. Remove primary cover.
    ness again! Refer to photo 2.
    6. Refer to your Factory Manual to remove clutch basket and
    associated components using proper safety Instructions,
    proper tools, and pullers.

    7. A hydraulic press is required to remove OEM clutch hub


    & install the Barnett Scorpion clutch hub.

    8. Using a hydraulic press remove the OEM clutch hub from


    the clutch basket. Firmly support the OEM basket as shown
    during this operation. After pressing the hub out; check the
    bearing for smoothness. If the bearing feels rough or
    binds, it must be replaced. Refer to photo 1.

    Photo 2
    (Continued on back)
    WARNING!

    Always wear proper eye protection when removing or


    installing snap rings. Slippage may propel the ring with
    enough force to cause eye injury. Use correct retaining
    ring pliers. Verify that the tips of the pliers are not
    excessively worn or damaged.

    Installing Your Scorpion Clutch Photo 4

    2. Install snap ring into rear of Barnett Scorpion hub; make 9. Using a new gasket, install clutch inspection cover as per
    sure the snap ring is correctly embedded in the snap ring factory instructions.
    groove.
    10. Re-install shifter lever, foot pegs, floorboards, etc.
    3. Re-install the clutch basket into the primary case (with
    chain and the associated components!) Using Red thread Clutch spring pressures
    lock on the transmission main shaft prior to installing the
    clutch hub nut. Tighten the hub nut using the factory
    torque specifications (50-60 foot lbs.) as instructed in Springs lbs. of Spring Pressure
    your factory manual. Refer to photo 3.
    MT-95-6 240 (40 lbs. each)

    MT-7-6 348 (58 lbs. each)

    MT-23-6 492 (82 lbs. each)

    MT-91-6 600 (100 lbs. each)

    Note:
    When using (3) & (3) combination, you must alternate
    every other spring.

    Photo 3

    4. Start by installing the "B" fiber plate (B plate has larger


    I.D.). Next, install the damper spring seat (flat steel band),
    then install the damper spring (curved steel band) with the
    white dot facing OUT. Follow with a steel plate, then
    fiber, steel, fiber, ending with a steel plate installed last.

    5. Install the pressure plate using (6) six MT-95 springs; (6)
    six spring cups; (6) six- 6mm SHCS.

    6. Torque 6mm screws to 5 ft. lbs.

    7. Adjust clutch and cable as per factory instructions.


    Refer to photo 4.

    8. Check and adjust primary chain as needed; re-install outer


    primary cover and pour proper amount and type of primary
    case lubricant through the clutch inspection opening. 805.642.9435 fax 805.642.9436
    2238 Palma Drive Ventura, CA 93003-5733
    www.barnettclutches.com

    You might also like