Principles of Communications Lecture 7: Analog Modulation Techniques

Principles of Communications
Lecture 7: Analog Modulation

Techniques (5)
Chih-Wei Liu
National Chiao Tung University
cwliu@twins.ee.nctu.edu.tw
Outlines
Linear Modulation
Angle Modulation
Interference
Feedback Demodulators
Analog Pulse Modulation
Delta Modulation and PCM
Multiplexing
Commun.-Lec7 cwliu@twins.ee.nctu.edu.tw 2
Analog Pulse Modulation
Message waveform is represented by regularly spaced

sample values (sample signals) discrete in time.
Historically, these methods are the early attempts to
achieve modern communications. They are in the twilight
zone between analog and digital modulations.
Today, their basic forms can still be found in some
electronic components such as ADC.
Analog/Digital Pulse-coded
Analog pulse modulation: A pulse train is used as the
carrier wave. Some characteristic feature of each pulse (e.g.,
amplitude, duration, or position) is used to represent message
samples.
PAM pulse amplitude
PDM pulse duration
PPM pulse position
Digital Pulse Modulation: Messages are discrete-amplitude
(finite levels) samples.
DM delta modulation
PCM pulse-code modulation
Pulse-Amplitude Modulation (PAM)
The amplitude of each pulse corresponds to the value of the
message signal m(t) (at the leading edge of the pulse).

t ( nTS + 0.5 )
mc ( t ) = m ( nTS )
n =
t 1, t < W 2
where =
W 0, otherwise
The pulse generator can be considered as a filter.
t 0.5
c
m ( t ) = m ( t ) h ( t ), h ( t ) =

M ( f ) = M ( f ) H ( f ), H ( f ) = sincf e j f
c
m ( t ) = n = m ( nTs ) ( t nTs ) sampled message

PAM Signals
Demodulation
Recover M(f) m(t) samples Mc( f )

M ( f ) =
Recover M(f) m(t) message H( f )
m c(t) 1/H(f) m (t) m(t)

LPF
equalizer
Equalizer: Recover distorted signals particularly when
the distortion method is known or estimated.
Pulse-Width Modulation (PWM)
Pulse width the values of message
Spectrum: complicated (Fourier-Bessel spectra)
PWM/PPM Generation
Mod: <Carlson,
Fig.6-3-2>
Demod: area of
pulse.
Low-pass filtering
(integration)
Pulse-Position Modulation (PPM)
Pulse position the values of message

x (t ) = g (t t )
n =
n
Spectrum: complicated
Demodulation: (1) LPF & integration
(2) convert PPM to PWM LPF
Conversion of PPM or PWM to PAM: a ramp generator
(re)starts at kTs and stops at tk. (next page)
Conversion Between PWM & PPM
<Carlson, Fig.6-3.3> (integration)
Delta Modulation
m(t) samples (analog amplitude) difference binary
or m(t) difference binary samples
Operations:
(1) d (t ) = m(t ) m s (t )
0 , d(t) 0
(2) (t ) = threshold (d (t )) =
0 , d (t ) < 0

(3) xc (t ) = samples of (t ) = (t ) (t - nTs ) = (nT ) (t nT )
s s
n =- n =

(nT ) ( nT )d
t
(4) ms (t ) = S S
n =-
DM Signal
Generation
Slope Overload
The message signal m(t) has a slope greater than can be
followed by the stair-step approximation ms(t).
Assume step-size = 0 slope (max) = 0/Ts
Solution to Overload
Adaptive delta modulation -- adjust the step-size 0

based on xc(t).
Idea: If m(t) constant, xc(t) alternates in sign
make 0 .
If m(t) ( or ) rapidly, xc(t) has the same polarity
make 0.
Method: Detect the trend of signal
Adaptive DM
ADM Receiver
Transmit step-size or regenerate the step-size at the
receiver according to pre-decided rules.
Pulse-Code Modulation (PCM)
m(t) samples (analog amplitude) quantized
samples binary representation binary modulated
waveform (ASK (AM), PSK (PM), FSK (FM) to be
discussed in Commun.II )
Main advantages of digital communication

more reliable communication
Main disadvantages of digital communication
wide BW (reduced by compression)
complicated circuits ( cost reduced by VLSI)
PCM Signal Generation
BW of PCM
Assume the number of quantization levels=q=2n
Message BW = W
Sampling rate = 2W
2nW binary pulses/second
1
Assume maximum width of pulse, =
2nW
transmission BW knW, k=constant
Hence, B k2Wlog2q
Recovered message error is due to mainly quantization
error. Thus, q error B
Multiplexing
A number of data sources share the same

communication channel.
z Frequency-Division Multiplexing (FDM)
z Quadrature Multiplexing (QM)
z Time-Division Multiplexing (TDM)
hmhang, EE/NCTU Nov 2009

FDM
Several
message
signals are
translated,
using
modulation,
to different
spectral
locations
and added
to form a
baseband
signal.
Example:
Stereophonic
FM
Quadrature Multiplexing (QM)
Quadrature-carrier multiplexing: transmit two signals on
the same carrier frequency. (not exactly FDM)
Note that cos and sin are orthogonal.
QM Quadrature Amplitude Modulation (QAM)
<Modulation>
xc (t ) = AC [m1 (t ) cos ct + m2 (t )sin ct ].
<Coherent Demodulation>
If the receiver has a carrier phase error, i.e.,
LO(t ) = 2cos(ct + ).
xr (t ) 2cos(ct + )
= AC [m1 (t )cos m2 (t )sin ]
+AC [m1 (t )cos(2ct + ) + m2 (t )sin(2ct + )].
yDD (t ) = AC [m1 (t )cos m2 (t )sin ]. (ideal : 0 )
Time-Division Multiplexing (TDM)
Each message signal occupies a small time slot in every
Ts second.
BW of TDM
A rough estimate of BW
Baseband message BW = Wi . There are N channels.
Samples per T second = 2WiT .
N
Total samples per T second: ns = 2WiT . Or,
i =1
N
Total samples per second = 2W .
i =1
i
N
Total baseband BW to accommodate all sources = B W .
i =1
i
Example:
Digital
telephony
system
Comparison of MUX
FDM: simple to implement,

inter-modulation distortion (crosstalk) due to nonlinear
channels
TDM: less crosstalk (in memoryless channels),
difficult to keep synchronization (frame structure, header),
digital (sampled) signals
QM: efficient use of channel, crosstalk between I & Q
channels (needs coherent demodulation)

Principles of Communications Lecture 7: Analog Modulation Techniques

Uploaded by

Copyright:

Available Formats

Principles of Communications Lecture 7: Analog Modulation Techniques

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Principles of Communications Lecture 7: Analog Modulation Techniques

Uploaded by

Copyright:

Available Formats

Principles of Communications

Lecture 7: Analog Modulation

Message waveform is represented by regularly spaced

m ( t ) = n = m ( nTs ) ( t nTs ) sampled message

Recover M(f) m(t) samples Mc( f )

m c(t) 1/H(f) m (t) m(t)

Pulse position the values of message

<Carlson, Fig.6-3.3> (integration)

Adaptive delta modulation -- adjust the step-size 0

Main advantages of digital communication

A number of data sources share the same

hmhang, EE/NCTU Nov 2009

FDM: simple to implement,

You might also like