ATR CUSTOMER SERVICES

FUEL
SAVING
CONTRIBUTING
TO A SUSTAINABLE
AIR TRANSPORT
DEVELOPMENT
 Introduction

The very competitive and deregulated nature of the

aviation market together with concerns over fuel price

Introduction rises, means that more than ever before, airlines focus
on how they can keep their fuel consumption down.
Indeed, they seek out operational cost reductions on
every single business facet. Fuel conservation has
become a major preoccupation for all airlines and aircraft manufacturers. That is why one should consider using
whichever ways and means there are to reduce fuel consumption, barring affecting safety; that, of course, must
remain the number one priority, at any time and for any airline.
Already, ATR aircraft are recognised as the most fuel-efficient aircraft in their category, thanks to high-tech
engines and propeller efficiency. Compared with an equivalent jet aircraft on a 300Nm average trip, the ATR
72-500 boasts a 35% block fuel saving per passenger.

This document depicts the many factors which affect fuel consumption and the latent gains or losses to be made.
Its purpose is to examine the influence of flight operations on fuel conservation with a view to making
recommendations that will enhance the potential for fuel economy.
Most of these factors are directly controlled by the airlines own employees (flight crews, operations/despatch
and maintenance staff) during flight preparation and in-flight. Fuel and cost efficient airlines will consider the
following main features to be paramount:
QThorough flight planning from very accurate data;
QCorrect aircraft loading (fuel weight and Center of Gravity);
QAn aerodynamically clean aircraft;
QFlight procedures that set speeds and altitudes in relevance with the companys economic priorities;
QDuring flight planning, the use of performance factors derived from an ongoing aircraft performance
monitoring programme.

None of the information herein is intended to replace procedures or recommendations contained in the Flight
Crew Operating Manuals (FCOM) or any other approved ATR manual, but rather to highlight areas where
maintenance, operations and flight crews can significantly contribute to fuel savings.

Introduction 1
Fu e l saving Contents

INTRODUCTION 1

A. FLIGHT PREPARATION 3
A.1. FLIGHT PLANNING 4
A.1.1. COST INDEX 4
A.1.2. WIND FORECASTING 5
A.1.3. CENTRE OF GRAVITY POSITION 6
A.1.4. ETOPS (EXTENDED RANGE WITH
TWIN-ENGINES AIRCRAFT OPERATIONS ) 7
A.2. FUEL RESERVES 7
A.2.1. CONTINGENCY FUEL REDUCTION 8
A.2.2. TANKERING FUEL 9
A.3. CRUISE PERFORMANCE MONITORING 10

B. FLIGHT MANAGEMENT 11
B.1. HOTEL MODE 12
B.2. TAXIING 12
B.2.1. TAXI PROCEDURE AT TAKE-OFF 12
B.2.2. TAXI PROCEDURE AT LANDING 12
B.3. CLIMB 13
B.4. CRUISE 14
B.5. DESCENT 14
B.5.1. STEEP DESCENT 14
B.5.2. LOW-THRUST DESCENT 15
B.6. APPROACH 16
B.7. HOW TO PERFORM AN ECOLOGICAL TRIP 16

C. MAINTENANCE 18
C.1. IMPLICATIONS OF DISPATCHING
UNDER MEL AND CDL 19
C.2. AIRFRAME MAINTENANCE 20
C.2.1. FLIGHT CONTROLS 20
C.2.2. WING ROOT FAIRING PANEL SEALS 20
C.2.3. MOVING SURFACE SEALS 21
C.2.4. DOORS, LANDING GEAR DOORS, MAIN
LANDING GEAR FAIRING AND ENGINE COWLS 21
C.2.5. DOOR SEALS 21
C.2.6. PAINT CONDITION 22
C.2.7. AIRCRAFT EXTERIOR CLEANING 22
C.2.8. AIRFRAME REPAIR 22
C.3. ENGINE MAINTENANCE 23
C.4. SYSTEMS MAINTENANCE 26

CONCLUSION 27

Contents 2
 A. Flight
preparation

A. Flight preparation 3
Fu e l saving

1. Flight Planning
The fundamental requirement for achieving optimised fuel economy and reduction of operating costs is
a quality Flight Planning System.
A good flight planning system will produce an optimized route, in terms of track, speeds and altitudes, which
meets the operators economic criteria. This track and vertical profile should be achieved during normal opera-
tions, given the constraints of ATC, climb rates, descent rates, etc. It will be based on good quality data (tem-
perature, wind, aircraft weight, payload, etc).
The ATR Flight Operations Software (FOS) includes a Flight Plan computation module which meets the custom-
ers needs for accurate fuel calculations.

1.1. Cost index

A technique that reduces fuel burn often requires more trip time. The choice of fuel saving is hence offset
by its impact on time related cost (hourly maintenance costs, flight and cabin crew costs and marginal
depreciation or leasing costs). The cost index is the cost of time ($/min) compared with the cost of fuel ($/
kg) and is used to obtain the best economics.
The determination of the cost index, is specific to each airline, depending on its economic policy. If fuel costs were
the overriding priority, i.e. fuel costs are much more significant than the cost of time, then the cost index would be
low. The aircraft would then be chosen to fly at minimum fuel/ cruise at long-range speed.
However if the cost of fuel was very cheap compared to the cost of time, then speed would be important and the
cost index would be high. The aircraft would then be chosen to fly at minimum time / cruise at maximum speed.
Best economics would be between these two speeds and would depend on the operators cost structure and oper-
ating priorities. For ATR aircraft, the speed range between maximum and long-range speed is restricted. For instance,
for an ATR 72-500 cruising at FL200; max cruise speed is 204 kt and long-range speed is 176 kt. Operators generally
chose to cruise at max speed, long-range speed, or at given intermediate IAS.
The fuel saving between a minimum time and a minimum fuel policy is valuable and leads to important fuel con-
sumption reduction. Let us consider the example of an average 300Nm trip performed with an ATR 72-500, for
which the fuel consumption difference between a cruise at maximum speed and a cruise at long range speed was
calculated with the FOS software, selecting an optimized cruise altitude. The fuel consumption reduction between
those two policies is up to 8%.

These standard cases, minimum fuel at FL 230 and minimum time at FL 180 serve as the reference for all examples
given in the following paragraphs.

Specific
Trip
Flight Airline Delta Delta Trip Delta Mean IAS consump- TOW
fuel FL
conditions Policy (kg) (%) time (min) (kts) tion (kg/ (tons)
(kg)
Nm)

Mini time 899 1h15 180 210 2.6 21

Standard (*)
Mini fuel 826 73 8.1 1h20 +5 230 175 2.2 21

Table A1: Fuel saving for a 300Nm trip with ATR72-500 depending on the airline policy (reference cases for
the fuel consumption).

(*) The standard flight conditions correspond to Climb 170kts / Descent 240 kts with 3 gradient, CG 25% and no wind at cruise level.

A. Flight preparation 4
 Flight preparation

To understand the trip fuel difference that can be attributed to the cruise flight level or to the cruise speed changes
between the two reference cases, the following Figure shows the fuel consumption versus cruise speed at different
flight level.

900
890
880
870
Trip fuel (kg)

860
850
840
830
820 Max Cruise
810
800 Long Range
FL 180 FL 200 FL 230

Figure A1: Fuel consumption for a 300Nm trip with ATR 72-500 versus cruise FL and speed

In addition to the fuel saving benefit, cruising at long-range speed reduces the temperature of the engine (ITT) and
improves consequently the lifetime of the components of the engine. This thus leads to engine maintenance costs
saving. Cruising at high flight levels has however an impact on the airframe structural fatigue. The airframe is more
pressurized at higher level, and its structure is stressed by the higher difference in pressure between the cabin and the
outside air. This may lead to more frequent maintenance inspections on the airframe, and may limit the total number
of aircraft cycles.

1.2. Wind forecasting

Winds have a significant influence on fuel consumption and it is valuable to consider this meteorological effect in
a fuel saving policy. The wind speed can vary with altitudes. For a given weight, when cruise altitude is lower than
optimum altitude, the specific range (distance covered versus fuel burnt) decreases. Nevertheless, it is possible
that, at a lower altitude with a favourable wind, the ground specific range improves. When the favourable wind
difference between the optimum altitude and a lower one reaches a certain value, the ground-specific range at
lower altitude is higher than the ground-specific range at optimum altitude. As a result, in such conditions, it is
more economical to cruise at the lower altitude.
For instance, let us assume that the headwind at FL180 is 20 kts and 50kts at FL230, the wind gradient is thus
+6kts/1000ft. In this case, in long-range speed, the specific range, is 0.39Nm/kg at FL 180 and 0.37 Nm/kg at
FL230, it is thus more valuable to fly at lower altitude. At long-range speed, the transition wind gradient from
which it is fuel economical to cruise at a lower flight level is about +4kts / 1000ft
However in max cruise speed, the specific range is 0.35Nm/kg for both FL 180 and FL230. It is thus equivalent
to fly at any of those FL. The transition wind gradient is higher in case of max cruise speed, around +6kts/1000ft
in average.

0,500
Specific range (Nm/kg)

FL 230
0,450 FL 220
FL 200
0,400
FL 180
0,350
0,300 Long-range
mean transition
wind gradient
0,250 + 4 kts /1000ft

0,200
0 20 40 60 80 100
Headwind (kts)

Figure A2: Wind altitude trade for optimised specific range at long-range speed

A. Flight preparation 5
Fu e l saving

0,500

Specific range (Nm/kg)

FL 230
0,450 FL 220
FL 200
0,400
FL 180
0,350
Max-cruise
0,300 mean transition
wind gradient
0,250 + 6 kts /1000ft

0,200
0 20 40 60 80 100
Headwind (kts)

Figure A3: Wind altitude trade for optimised specific range at max cruise speed

The wind effect really depends on the days weather conditions and the flight crew can optimize the specific range by
monitoring their specific fuel consumption.

FuelFlow
SFC =
GS

1.3. Centre of gravity position

The gross weight is the sum of the dry operating weight, payload and fuel and acts as one force through the
centre of gravity (CG) of the aircraft. The load and trim chart allows the determination of the overall centre of
gravity of the airplane taking into account the centre of gravity of the empty aircraft, the fuel and the payload
distribution. It must be ensured that the centre of gravity is within the allowable range referred to as the centre of gravity
operational envelope.
A more forward centre of gravity requires a nose up pitching moment obtained through reduced tail plane lift, which
is compensated for by more wing lift. This creates more induced drag and leads to an increase in fuel consumption.
It is better to have the centre of gravity as far aft as possible. As a rearward shift in CG position reduces the dynamic
stability of the aircraft, the CG envelope defines the aft limit.
The position of the centre of gravity has a limited impact on the ATRs fuel saving. Nevertheless, choosing an aft rather
than a forward balance leads to a slight gain in fuel consumption.
Let us consider the example of the reference 300Nm trip performed with an ATR 72-500.
The fuel consumption reduction with an aft balance of 34% is at the utmost 0.6% when comparing to the same flight
in 25% CG conditions.
The aft balance conditions of flight are: standard procedures, CG 34% and no wind at cruise level.

Flight Delta Delta Trip Delta Cruise

Airline Policy Trip fuel (kg)
conditions (kg) (%) time (min) FL

Aft Mini time 897 2 0.2 1h15 +0 180

balance
34% Mini fuel 821 5 0.6 1h20 +0 230

Table A2: Fuel saving for a 300Nm trip with ATR72-500 with aft balance

In the opposite, a forward balance of 17% leads to an extra fuel burn of 0.6% when comparing to the same flight in
25% CG conditions.

A. Flight preparation 6
 Flight preparation

Flight Delta Delta Trip Delta Cruise

Airline Policy Trip fuel (kg)
conditions (kg) (%) time (min) FL

Forward Mini time 901 +2 +0.2 1h15 +0 180

balance
17% Mini fuel 831 +5 +0.6 1h20 +0 230

Table A3: Extra fuel consumption for a 300Nm trip with ATR72-500 with forward balance

Globally, from the most forward to the most aft CG position, the fuel economy is only 1.2% in case of mini fuel, and
0.4% in case of mini time policy.

1. 4. ETOPS (Extended range with Twin-engines aircraft

Operations)
The ETOPS concept aims to settle and support the operations of twin-engine aircraft on long distances.
It allows operating twins on routes containing points further than 60 minutes flying time from an adequate landing
airport. When required to fly over water or deserted areas, ETOPS allows more direct routes and thus leads to
fuel saving.
The ATR 42-500 and 72 aircraft are certified with an ETOPS capability of 120 minutes.

2. Fuel Reserves
Fuel is loaded onto the aircraft as follows:
QTaxi fuel QTrip fuel QContingency fuel
QAlternate fuel QFinal reserve fuel QAdditional fuel
QExtra fuel QTankering fuel
In order to avoid unnecessary fuel weight, the flight must be planned very precisely to calculate the exact fuel
quantity to be embarked. Flight preparation should be based on aircraft performance monitoring by taking into
account performance factors derived from specific range variations.
The fuel reserves will be based on a policy that aims at obtaining the minimum values required within the regula-
tions, a fuel saving can be especially achieved on the contingency fuel reserve.
To minimize the alternate fuel, the alternate airports should be chosen as near as possible to the destination.
Both the JAA and FAA do not require the alternate fuel reserve in certain cases, depending on meteorological
conditions and the suitability of the airport, but be aware than in that case an additional fuel of 15min is required.
Another part of the reserves is the extra fuel, which is at the Captains discretion. There are many reasons why
this extra fuel is necessary. It could be due to uncertain weather conditions or availability of alternate and destina-
tion airfields, leading to a probability of re-routing. It may also be due to lack of confidence in the flight planning
and the natural desire to increase reserves. This is the one area where a significant impact can be made through
accurate flight preparation.

A. Flight preparation 7
Fu e l saving

2.1. Contingency fuel reduction

Within JAR OPS, there are several definitions of contingency fuel, depending on diversion airfields, fuel con-
sumption monitoring, etc. but briefly the fuel is the greater of two quantities:
Q5 minutes hold fuel at 1500 feet above destination at ISA
QO ne of the following quantities:
5% of trip fuel,
3% of trip fuel with an available en-route alternate aerodrome,
an amount of fuel which ensures an appropriate statistical coverage
of the deviation from the planned to the actual trip fuel,
20 minutes trip fuel, based upon trip fuel consumption.
The last 3 options require Authority approval and the last 2 options require fuel consumption monitoring program.
One further method of reducing the contingency fuel is by using a decision point or redispatch procedure. This involves
the selection of a decision point where the aircraft can either continue to the destination, as the remaining fuel is suf-
ficient, or it can reach a suitable proximate diversion airport.

a) En-route alternate airport

The contingency fuel can be reduced from 5% to 3% providing an en-route alternate is available. Appendix 2 to
OPS 1.255 defines the en-route alternate as an aerodrome which shall be located within a circle having a radius
equal to 20% of the total flight distance, the centre of which lies on the planned route at a distance from the des-
tination aerodrome of 25% of the total flight plan distance, or at least 20% of the total flight plan distance plus
50 Nm, whichever is greater.

$UULYDO

3BEJVTFRVBMUP 1P
PGUIFUPUBM
EJTUBODF 1P

$JSDMFDFOUFSFEPOUIF
QMBOOFESPVUFBUBEJTUBODF
GSPNUIFEFTUJOBUJPOFRVBM
UPPGUIFUPUBMEJTUBODF
'HSDUWXUH PS/N XIJDIFWFS
JTHSFBUFS
5DQJH1P

Figure A4: En-route alternate aerodrome location

The reduction of the contingency fuel from 5% to 3% has a limited impact on the ATRs fuel saving. Indeed, this aircraft
operates on short trip distance and furthermore its transport coefficient (refer to B. 2. 2.Tankering fuel) is very low.
For the reference 300Nm trip, taking 3% contingency fuel instead of 5% allows to transport around 20kg less fuel. But
this fuel is almost entirely recoverable at destination as the ATR transport coefficient is low.
The longer the trip distance is, the more valuable is this contingency fuel reduction.

b) Decision point procedure

This procedure permits aircraft to carry less contingency fuel than in the standard case.
Operators select a point called the decision point along the planned route (Figure 2). At this point, the pilot has two
possibilities:
QReach a suitable proximate diversion airport, taking into account the maximum landing weight limitation,
QContinue the flight to the destination airport, when the remaining fuel is sufficient.

A. Flight preparation 8
 Flight preparation

A B C

Departure Decision Destination

airport point airport

E Destination 2 D Alternate
airport airport

Figure A5: Decision point procedure

Comparing the standard fuel planning and the decision point procedure fuel planning, the maximum contingency fuel
reduction is 5% of the trip fuel between departure airport A and decision point B.

Destination
airport
Decision
point

Fuel saving
quired
ency fuel re
Conting
ency
Conting uired
fuel re q

Distance

2.2. Tankering fuel

The normal message regarding fuel burn is that it is more economical to carry the minimum amount required
for the sector. However there are occasions when it is economic to carry more fuel. This is when the price of fuel at
the destination airfield is significantly higher than the price at the departure airfield.
However, since the extra fuel on board leads to an increase in fuel consumption the breakeven point must be
carefully determined.

TOW
K is the transport coefficient: K =
LW

The addition of one ton to the landing weight, means an addition of K tons to the take-off weight. For instance, if K=1.1
and 550 kg fuel is added at the departure, 500 kg of this fuel amount will remain at the destination. So carrying half a
ton of fuel costs 50 kg fuel more.

Let us consider the example of the reference 300Nm trip performed with an ATR 72-500.

Flight
Airline Policy TOW (tons) LW (tons) K
conditions

20 19.21
Mini time 1.018
16 15.28
Standard
20 19.12
Mini fuel 1.005
16 15.14

Table A4: Transport coefficient for a 300Nm trip with an ATR72-500

On ATR aircraft, the transport coefficient is actually very low, and even lower in case of a mini fuel policy. That means
that almost all of the extra fuel carried will be recoverable at destination.

A. Flight preparation 9
Fu e l saving

Tankering fuel may be valuable when a fuel price differential exists between two airports.
QThe extra-cost of the loaded fuel at departure is:
Extra fuel weight departure fuel price: TOW Pdeparture=K LW Pdeparture
QThe cost saving of the transported fuel is:
Transported fuel arrival fuel price: LW Parrival
QThe cost due to a possible increase in flight time is:
Flight time increase cost per hour: T Ch
It is thus profitable to carry extra fuel if the cost saving exceeds the extra fuel loaded cost plus the extra time cost.
That is to say: LW P > K LW P+ T C
LW (P K P) - T C > 0
Therefore, if T = 0, it is profitable to carry extra fuel if the arrival fuel price to departure fuel price ratio is higher than
the transport coefficient K.
Parrival
>K
Pdeparture

3. Cruise performance monitoring

In order to avoid unnecessary fuel weight, the flight must be planned very precisely to calculate the exact fuel
quantity to be embarked. Flight planning should be based on aircraft performance monitoring by taking into account
performance factors derived from specific range variations.
In case of excessive fuel flow, or drag increment detected through the monitoring of the performance, an investigation
can be carried out to determine their causes. Then the appropriate maintenance corrective action (surface clean up,
engine wash) can be done to improve the aircraft performance.
The Module 5 of the FOS, Cruise Performance Monitoring (CPM), is a valuable tool to assess the possible deviation in
aircraft performance and to monitor the drag trend. It brings better insight to the airline analysts to identify engine per-
formance degradation or fuselage drag. The CPM module enables comparison of aircraft cruise performance, mainly
torque, fuel flow and IAS, measured in flight with theoretical data computed by the FOS.
For aircraft fitted with the Multi Purpose Computer (MPC), the parameters are recorded automatically during the stabi-
lised cruise phase and stored in the PCMCIA card of the MPC. The downloading of the Cruise report files into FOS
is then easily achieved by inserting the card in a laptop. A manual mode for data entry is available for other aircraft
where the measurements are to be performed by the crew.

A. Flight preparation 10
 B. Flight
management

B. Flight management 11
Fu e l saving

The following paragraphs describe some applicable procedures that lead to fuel economy. Though, be care-
ful that before applying those procedures, the changes induced to the flight management have to be studied
and the SOP updated accordingly.

1. Hotel mode
When the aircraft stands at the ramp, in hotel mode, the fuel consumption is 110kg/hour for the PW127 engine.
When the airport facilities allow it, the use of the GPU to deliver the required power supply on ground is fuel
economical.

2. Taxiing
Good estimate of taxi times are required. Actual times need to be monitored and standard estimates changed as
necessary. Engine performance is optimised for flight conditions, but all aircraft spend considerable time on the ground
taxiing from the terminal out to the runway and back. This leads to a waste of precious time and fuel.
To optimise the taxiing distances, the flight crew shall choose to reach and leave the runway from intermedi-
ate taxiways when the entire runway length is not necessary according to the take-off and landing performance
calculations.

2.1. Taxi procedure at take-off

The standard procedure recommended by ATR requires two-engines taxiing. Indeed, even if fuel economical,
taxiing with one engine has the following disadvantages:
g this procedure is not recommended for uphill slopes or slippery runways
g no fire protection from ground staff is available when starting engine away from the ramp
g mechanical problems can occur during start up of the other engine, requiring a gate return
for maintenance and delaying departure time.

2.2. Taxi procedure at landing

FCOM procedures require not less than a defined time before shutting down the engine after landing. The
cool-down time after reverse operation, prior to shut down has a significant effect on engine life.
It is thus recommended that once the runway is cleared, engine 1 is feathered, and that once the appropriate
cooling time has expired, it is shut down, even if the parking stand has not been reached.

When taxiing with one engine shut down, the electrical supply of the hydraulic system is done by one engine only.
Some precautions have thus to be taken to check that the whole hydraulic system, notably in charge of the braking
and the steering, remains correctly supplied by the remaining engine. The SOPs have to be changed accordingly.
Besides, those procedures are absolutely not recommended in case of uphill slopes or slippery runways.

B. Flight management 12
 Flight management

3. Climb
Depending on speed laws, the climb profiles change. The higher the speed, the lower the climb path, the more time
spent at low flight level, the longer the climb distance and the more fuel burnt.

Cruise level

Low speed

High speed

Figure B1: Climb profiles

In the FCOM, two climb speeds are proposed: 170kts and 190kts. The difference in fuel consumption between a low-
speed and a high-speed climb to a fixed cruise level is valuable.
The fuel economy for a climb to FL180 between a 170kts-climb and a 190kts-climb is up to 58kg with an ATR 72-500
which represents an economy of 26% of the fuel used during the climb phase.

58kg fuel saved for

a climb at low-speed

Table B1: Fuel consumption for different climb profiles for an ATR72-500

B. Flight management 13
Fu e l saving

4. Cruise
In cruise, the torque set automatically by the power management corresponds to the maximum cruise rate. The use of
a derated cruise torque, which corresponds to a long-range torque, is advisable in order to save fuel. The fuel economy
done between a long-range and a max cruise is estimated in Table 3: Reference cases for the fuel consumption.
The condition to use a derated cruise power is that the corresponding cruise tables for IAS, TAS, TQ, FF are provided
to the flight crew and that the operational procedures warn the fact the power lever is set out of the notch and that
the torque management is no longer automatic.
The Module 2 of the FOS, In-flight performance, enables to compute twin or single-engine cruise performance charts,
with the desired optimum cruise speed. The charts edited are similar to the ones published in the FCOM.
Another means to save fuel is to shorten the cruise routes. This can be achieved by asking Air Traffic Control for direct
routings whenever possible in cruise.

5. Descent
There are two main parameters to act on when willing to lower the fuel burnt for the descent: the speed and the
descent gradient whose combination determines the thrust required. The influence of both parameters is developed in
the following paragraphs, and some recommendations are done to optimize at most the fuel consumption.
Whatever the type of descent chosen, a decisive point to consider during the flight management is to optimize the Top
Of Descent (TOD) in order to reach the approach altitude as close as possible to the initial approach point to avoid
leveling off far before this point, which is an important waste of fuel.

5.1. Steep descent

The normal procedure for a descent is to select 3 descent slope and to maintain the IAS by adjusting the
thrust. Descending at a higher slope enables to save fuel, as less thrust is required for the descent. The TOD occurs
later and the flight at cruise flight level is longer.

/DWHU72'
6WHHSHUGHVFHQW

*"4LUT
TMPQF

*"4LUT
TMPQF

Figure B2: Descent profiles at given IAS

Besides, at a given gradient of descent, the slower the IAS selected, the less fuel is burnt during the descent, as less
thrust is required.

B. Flight management 14
 Flight management

51kg fuel less

for a descent
at a steeper
gradient

TOD reached
17Nm later

23kg fuel
saved for a
slower descent

The steeper descent means remaining in cruise

power longer until the TOD is reached, thus increas-
ing the cruise fuel consumption. However, the fuel
saved during the descent, as shown in Table 8,
is more important than the fuel required to cruise
longer, and on the whole, there is a noticeable fuel
reduction.

Table B2: Fuel consumption for different descent profiles for an ATR72-500

Descent Delta
Flight Airline Trip fuel Delta Delta Trip Delta Cruise
IAS TOD
conditions Policy (kg) (kg) (%) time (min) FL
(kts) (Nrm)

Steep Mini time 894 5 0.6 1h16 +0 240 +13 180

descent
4 slope Mini fuel 813 13 1.3 1h21 +1 240 +17 230

Table B3: Fuel saving for a 300Nm trip with ATR72-500 with a steeper descent profile

5.2. Low-thrust descent

To optimize at most the fuel consumption during the descent, the torque should theoretically be reduced until
the thrust is nil. In this case the propeller is said to be transparent, i.e. the propeller drag is reduced to the
minimum achievable with a rotating propeller.
The associated operating procedure is to select a speed and a gradient for descent that requires low thrust to maintain
them, which means a lower descent torque than the one for standard procedure.
Let us take the example of the reference 300Nm trip performed with an ATR 72-500.
A descent performed at 4descent slope and IAS 200kts selected requires low TQ and allows important fuel saving
compared to the same descent in standard conditions.
The low thrust descent is even more fuel economical than the steep descent when comparing the following values
with the one from Table 9. However it can lead to operational limitation, as the speed selected for descent is too low
to fit in with the local airport traffic.

B. Flight management 15
Fu e l saving

Descent Delta
Flight Airline Trip fuel Delta Delta Trip Delta Cruise
IAS TOD
conditions Policy (kg) (kg) (%) time (min) FL
(kts) (Nrm)
Low-trust
Mini time 880 19 2.1 1h16 +1 200 +13.1 180
descent

4 slope Mini fuel 793 33 4.0 1h23 +3 200 +17.3 230

Table B4: Fuel saving for a 300Nm trip with ATR72-500 with a low thrust descent profile

6. Approach
At landing, providing that the particular countrys regulations permit, and when wind conditions allow it,
the flight crew can request to the Air Traffic Control to change the QFU to shorten the approach procedure.
Besides, visual approaches are generally shorter than instrument ones. The former have thus to be chosen in priority.

7. How to perform an ecological trip

When combining all the positive effects on fuel consumption detailed in the previous flight preparation and flight man-
agement parts, the resulting fuel saving is considerable. The following figure shows how the adoption of ecological
reflexes can lead to great fuel economy.

0D[&UXLVHWKUXVW
&UXLVH)/ 7ULSIXHONJ
6WDQGDUGGHVFHQWNWV 7ULSWLPHK
&*

oLH +LJKHUFUXLVH
LJKHUFUXLV
UF
NJO DOWLWXGH
&UXLVH)/
LVH)/

7ULSIXHONJ
7ULSWLPHK

&UXLVHDW
LV
oLH ORQJUDQJH
RQJUDQJ
NJO VSHHG

7ULSIXHONJ *OREDOHFRQRP\
oLH
7ULSWLPHK NJO

'HVFHQWDW
'HVFHQWDW
FH
oLH ORZWKUXVW
RZWKUXV
NJO NWV
NWV

7ULSIXHONJ
7ULSWLPHK

oLH $IW&*
IWW &
NJO 

/RQJ5DQJHWKUXVW
&UXLVH)/ 7ULSIXHONJ
/RZWKUXVWGHVFHQWNWV
7ULSWLPHK
&*

Figure B3: Fuel saving for a 300Nm ecological flight with an ATR 72-500

B. Flight management 16
 Flight management

The same calculations have been carried out for ATR 42-500 on the same route, with TOW=18t.

0D[&UXLVHWKUXVW
&UXLVH)/ 7ULSIXHONJ
6WDQGDUGGHVFHQWNWV 7ULSWLPHK
&*

oLH +LJKHUFUXLVH
LJKHUFUXLV
UF
NJO DOWLWXGH
&UXLVH)/
LVH)/

7ULSIXHONJ
7ULSWLPHK

&UXLVHDW
LV
oLH ORQJUDQJH
RQJUDQJ
NJO VSHHG

7ULSIXHONJ *OREDOHFRQRP\
oLH
7ULSWLPHK NJO

'HVFHQWDW
'HVFHQWDW
FH
oLH ORZWKUXVW
RZWKUXV
NJO NWV
NWV

7ULSIXHONJ
7ULSWLPHK

oLH $IW&*
IWW &
NJO 

/RQJ5DQJHWKUXVW
&UXLVH)/ 7ULSIXHONJ
/RZWKUXVWGHVFHQWNWV
7ULSWLPHK
&*

Figure B4: Fuel saving for a 300Nm ecological flight with an ATR 42-500

In addition to those actions, other economies can be done during the ground phase, when parked at the ramp or when
taxiing, especially at congested airports.

B. Flight management 17
C. Maintenance

C. Maintenance 18
 Maintenance

1. Implications of dispatching under

MEL and CDL
Operators are provided with a Master Minimum Equipment List (MMEL) that is the basis for their MEL
(Minimum Equipment List).
The MEL is a valuable tool for optimizing dispatch reliability because it defines the conditions under which the
aircraft may be dispatched with specified equipment inoperative. The conditions include the period during which
the aircraft can be operated with the system inoperative and, in some cases, requirements for additional fuel load.
The Configuration Deviation List (CDL) in chapter 7 of the Aircraft Flight Manual (AFM) also allows the aircraft to
be dispatched with specified components not fitted. All components must be re-installed at the earliest mainte-
nance opportunity (nominally within 1 week, subject to local airworthiness authority approval). For items whose
loss or failure will bring a fuel consumption penalty it is beneficial to make special efforts to replace them as soon
as possible.
The following table indicates the MMEL and CDL items that will have a noticeable negative impact on fuel cost.

System / Component MMEL Condition Remarks

21-23-1 Flight level is limited No flight level optimization for the trip fuel calculation
Overboard valve to FL 170
21-23-2 Flight level is limited No flight level optimization for the trip fuel calculation
Underfloor valve to FL 170
21-23-3 Flight level is limited No flight level optimization for the trip fuel calculation
Extract Fan to FL 170
21-30-1 Maximum operating High fuel consumption due to low flight altitude
Pressurization system altitude 10 000 ft
21-50-1 Flight level is limited An in-flight failure could imply total loss
Packs to FL 170 of pressurization; fuel consumption at FL100
must be taken into account to compute the trip fuel.
21-61-1 If pack is not used, an in-flight failure could imply
Pack Auto temperature total loss of pressurization, fuel consumption at
controls FL100 must be taken into account to compute
the trip fuel.
28-23-1 Alternate route study must be performed taking
X feed valve into account the lowest tank value only.
32-31-3 Flight with landing
Landing gear lever gear down
retraction system and
uplocking system
31-48-1 Flight level is limited No flight level optimization for the trip fuel calculation
MFC module 2A to FL 170
36-11-2 Flight level is limited An in-flight failure could imply total loss of
Bleed valves to FL 170 pressurization; fuel consumption at FL100 must be
taken into account to compute the trip fuel.

Table C1: MEL items impact on fuel consumption

C. Maintenance 19
Fu e l saving

System / Component CDL Items Remarks

32-1, 1bis, 3 & 4 Main gear door Increased drag
32-2 Nose gear forward door Refer to 32-31-3 in MEL
52-1 to 9 Doors Increased drag
61-1 Propeller spinner Decreased efficiency Increased drag
79-1 Engine oil cooler flap Refer to 32-31-3 in MEL

Table C2: CDL item impact on fuel consumption

2. Airframe maintenance
The airframe is a complex shape and includes many panels, doors and flight control surfaces.
In order for the aircraft to perform at its optimum efficiency (i.e. to create the lowest amount of drag), the airframe must
be free from any irregularities. This means that surfaces should be as smooth as possible, panels and doors should be
flush with surrounding structure and all control surfaces should be rigged to their specified positions.
Deterioration of the aircrafts external surface is a normal consequence of its use. One objective of the maintenance
schedule is to preserve aircrafts operational efficiency by the most economic means possible. This is achieved through
inspection, and subsequent repair as necessary, in specified areas at specified intervals. These intervals are the mini-
mum allowable and the industry is constantly seeking to extend all task intervals. Carrying out any maintenance task
more regularly will inevitably increase maintenance costs. However, in this section we consider tasks that can bring
considerable reductions in fuel consumption when the need for repair is discovered.
In terms of overall airframe condition (dents, panel gaps, under or over filled panel joints, etc) particular attention
should be paid to areas of the airframe that air impinges on first (e.g. forward portion of the fuselage, the nacelles, the
wings, the fin, etc).
The following sections highlight airframe problems that are both typical in-service and have a particularly negative
impact on aerodynamic performance.

2.1. Flight controls

Correct rigging of all flight control surfaces is important to aerodynamic efficiency. Specific caution should be
paid to the spoiler on upper surface indeed. These flight controls are only occasionally deployed during the flight, but
are fitted to areas of the wing that are particularly sensitive to imperfections. Such imperfections occur when a spoiler
is not flush with the wing profile. The effect on aircraft performance varies with the size of the gap.

Refer to: QAdjustment of aileron control JIC 27-10-00-ADJ-10000

QAdjustment of rudder control JIC 27-20-00 ADJ-10000
QAdjustment of elevator control JIC 27-30-00 ADJ-10000
QAdjustment of flap control JIC 27-51-00 ADJ-10000
QAdjustment of spoilers control JIC 27-61-00 ADJ-10000

2.2. Wing root fairing panel seals

The aircraft exterior transitions, between the wing root and the fuselage are performed via many fairing panels.
These panels are not part of the aircrafts primary structure but they perform an important role in managing the airflow
in this aerodynamically critical area. Flexible seals, which are sometimes referred to as Karman seals, cover gaps
between the panels and the adjacent wing or fuselage structure.

Refer to: QRemoval and installation of wing-to-fuselage fairing JIC 53-93-00 RAI 10000

C. Maintenance 20
 Maintenance

2.3. Moving surface seals

Gaps between the various sections of the aircrafts structure can disrupt local airflow and this will generate
unnecessary drag, and have a consequent impact on fuel consumption. Flexible seals are often used to fill exter-
nal gaps between moving surfaces and access panels and their surrounding structure.
The effect on fuel consumption of moving surface seals that are often found missing or damaged in-service, has a
particularly negative impact on aerodynamic performance.

2.4. Doors, landing gear doors,

main landing gear fairing and engine cowls
Mis-alignment or mis-rigging on any doors and main or nose landing gear door will lead to unnecessary drag
being generated.

Refer to: QPax/crew door adjustment JIC 52-11-00-ADJ-10000

QFlt compt ovhd hatch adjustment JIC 52-22-00-ADJ-10000
QPax compt emer exit adjustment JIC 52-21-00-ADJ-10000
QCargo door adjustment JIC 52-31-00-ADJ-10000
QService door adjustment JIC 52-42-00-ADJ-10000
QMLG doors adjustment JIC 52-81-00-ADJ-10000
QNLG doors adjustment JIC 52-82-00-ADJ-10000

Figure C1: Example of misrigged door

2.5. Door seal

The passenger, service and cargo doors seals serve a dual function.
These seals not only fill the gap between the door and its surrounding structure but they also render the door airtight.
This allows the aircraft to be pressurized efficiently. A damaged, leaking seal allows pressurized cabin air to escape in
a direction perpendicular to the fuselage skin. The effect on the local airflow can be quite significant.

C. Maintenance 21
Fu e l saving

2.6. Paint condition

Deterioration of the aircrafts exterior surface is to be expected on any aircraft in service.
The rate of deterioration can vary with the intensity of the utilization and environmental conditions. Although the thick-
ness of paint is typically around 1/3 millimeter its loss in critical areas of the airframe will upset the local airflow to an
extent that overall drag can be increased. Particular attention should be paid to the nose and cockpit area and the
wing upper and lower surfaces.

2.7. Aircraft exterior cleaning

The natural accumulation of dirt on the aircrafts external surface will introduce a slight roughness that, overall,
can induce significant additional drag.

Refer to: g Aircraft exterior cleaning JIC 12-21-11-CLN-10000

2.8. Airframe repair

Damage to the airframe, due to impact during handling or taxi, or following collision with birds, have to be
repaired. These repairs generate some additional drag, and add some extra load.

Figure C2: Steps and Gaps at skin joints

Figure C3: Example of repair on the airframe

C. Maintenance 22
 Maintenance

3. Engine maintenance
An enhanced relationship between pilots and maintenance crews can be very beneficial towards engine durability. The
proper engine handling behaviors will reduce the maximum or sustained engine temperatures towards increased hot
section life. Some airlines have implemented yearly meetings/training with pilots to enhance awareness and increase
collaboration.
During normal operations all engines will experience rubbing, thermal stress, mechanical stress, dirt accumulation,
foreign object ingestion and so on. These effects will eventually result in a measurable decrease in performance.

Figure C4: Example of engine degradations

Typical indicators of engine performance are:

g interturbine temperature (ITT) increases as engine efficiency decreases. More fuel is required to achieve a
given power. An increase in fuel required will typically produce an increase in ITT. Monitoring ITT margin at
take-off is a good indicator of engine deterioration. This can easily be done using data recorded during the
flight that is subsequently processed on the ground by engine condition trend monitoring software.
g Specific Fuel Consumption (SFC) also typically increases as engine efficiency declines (again, due to the
need for more fuel to achieve a given power). This SFC degradation has a direct impact on aircraft perfor-
mance in terms of Specific Range and thus on the fuel burnt for a given mission.
The degradation of parameters and the consequences for fuel consumption must be balanced against the significant
costs that will be incurred when the engine is eventually removed from the aircraft for overhaul. The moment of the
engines overhaul may be postponed through careful maintenance of the engine while it remains on wing.
When the time to remove the engine arrives, the extent and cost of the overhaul and refurbishment must be carefully
balanced against the improvements in ITT margin and fuel consumption it will bring. These aspects should be carefully
assessed and regularly reviewed with the engine manufacturer or using the services of one of the many third party
engine support companies.
Routine monitoring of engine and aircraft performance using the tool provided by the engine manufacturer and Cruise
Performance Monitoring software (see A. 3 Cruise performance monitoring) will not only allow long-term performance
degradation to be assessed but also permit detection of unexpected shifts in engine/aircraft performance. Timely
detection will allow appropriate maintenance actions to be launched and minimize any additional fuel consumption
associated with the problem.

C. Maintenance 23
Fu e l saving

ITT
Margin

Shop visit Shop visit

Hours of cycles

Figure C5: Recovery of the ITT margin, after shop visits

The Performance Recovery Wash is a valuable fuel saving method that should be considered for all operations.
This method uses cleaning agents to wash gas path components followed by a thorough rinse. The purpose is to
remove baked-on deposits in environments with severe air contaminants. The benefits are a small recovery of ITT
margin (typically 5 to 8C) but, more importantly, reducing the accumulation of baked-on deposits with proper wash
frequency i.e. continuously remove small build-ups. The frequency is a function of environment / mission and varies in
the field from bi-weekly to monthly or more.
Typically, operators in harsh environments will have a higher frequency and complement with other washing methods.
Operators in benign environments tend not to implement this wash method in their program. As a small recovery of
ITT margin is expected, some operators also perform this wash near the end of the hot section life to further extend
time-on-wing.
Engine washing is labor intensive and the washing method(s) and frequency need to be adjusted by trial and error to
optimize the investment in consideration of hot section life.

Performance
recovery at each
Unwashed engine washing
ITT
Margin

Cumulative
benefits

Cycles

Figure C6: Performance recovery after engine washing

C. Maintenance 24
 Maintenance

For further information on the engine wash, refer to the Pratt&Whitney Maintenance Manual chapter 72-00-00
Engine Cleaning/Painting.

Figure C7: Wash nozzle connection

C. Maintenance 25
Fu e l saving

4. Systems maintenance
Repair of the leaking on the pneumatic system and deicing systems, saves fuel.
Problems of leaks are identified with the aircraft performance monitoring software (FOS module 5).

Refer to: g Check of bleed duct tightness JIC 36-11-00-CHK-10000

Figure C8: leak inspection
of the pneumatic duct

Refer to: g Operational test of regulator and shut off valve

by using fire handle JIC 30-11-61-OPS-10000
Figure C9: Test port
on the deicing valve

C. Maintenance 26
 Conclusion

There are many factors that influence the fuel used by air-
craft, and this report highlights how a combined effort of the
different actors of the airline, flight dispatchers, pilots and

Conclusion maintenance engineer, can lead to considerable saving on

the fuel burnt each year by an airline, and thus minimizing the
environmental impact of their fleet.

ATR has made the choice of advanced technologies providing fuel-efficient aircraft to the airline which is consistent
with its willing to reinforce its contribution to ensure a sustainable future for the air transport.

Conclusion 27
Fu e l saving

Dear Reader,
All efforts have been made to ensure the quality of the present document.
However do not hesitate to inform ATR Flight Operations support of your com-
ments at the following address: flight-ops-support@atr.fr

The Flight Operations Support team

Printed on 100% recycled paper using vegetable inks

 ATC January 2011
All reasonable care has been taken by ATC to ensure the accuracy of the present document.
However this document does not constitute any contractual commitment from the part of ATC which will offer,
on request, any further information on the content of this brochure. Information in this brochure is the property of ATC
and will be treated as confidential. No use or reproduction or release to a third part may be made there
of other than as expressely authorized by ATC.
 Contact

For ordering manuals, please contact us at:

Phone: +33 (0)5 6221 6207
e-mail: atc@atr.fr
ATR Customer Services Portal: https://www.atractive.com

ATR Customer Services - January 2011

Avions de Transport Rgional. 1, alle Pierre-Nadot 31712 Blagnac Cedex - France
Phone: +33 (0)5 62 21 62 07 - Fax: +33 (0)5 62 21 63 67 - https://www.atractive.com