The Ultra-Aire 70H is the first compact, high-efficiency, whole-house ventilating
dehumidifier designed to fit in tight, low-clearance applications. The unit removes up to 70 pints per day, is ENERGY-STAR rated and provides effective air filtration (MERV 11). The UA 70H is designed to handle up to 1800 sq. ft, which makes it ideal for a small home, condo or apartment application. The unit can be tied into a forced air duct system, ducted with separate ducting or used in a freestanding application and can be installed in mechanical rooms, closets, attics, basements and crawlspaces. The UA70H has an innovative cabinet design that easily converts to either vertical or horizontal airflow discharge which allows for easier installation in tight spaces. Flexible airflow configurations allow the UA70H to be installed in locations where other 4033730 dehumidifiers dont fit due to duct issues and size constraints.
ULTRA-AIRE 70H SPECIFICATIONS
One of the best Limited Warranties Part Number: 4033730 in the industry today Blower: 150 CFM @ 0.0" WG 1 YEAR 100% All Parts and Labor 140 CFM @ 0.2" WG 5 YEARS 100% Condenser, 130 CFM @ 0.4" WG WARRANTY Evaporator, and Compressor only (with certain limitations) Power: 580 Watts @ 80F and 60% RH Supply Voltage: 115 VAC 1phase 60 Hz OPTIONAL ACCESSORIES Current Draw: 5.1 Amps 4028539 DEH 3000 Control 4028407 DEH 3000R Control (with remote) Energy Factor: 2.4 L/kWh 4030671 MERV 11 Filter (9"x11"x1") Operating Range: Between 49F and 95F Max (Inlet Air Temperature) 4030734 MERV 11 Filters 4-Pack Sized for: Up to 1,800 Sq. Ft. - Typical 4030733 MERV 11 Filters 12-Pack 4030113 Pump Kit Minimum Performance at 80F and 60% RH 4029908 Hang Kit Water Removal: 70 pints/day 4025287 MERV 14 Filter Housing Efficiency: 5.0 Pints/kWh 4024370 MERV 14 Filter (20"x24"x4") Duct Connections: 8" Round Inlet; 8" Round Outlet 4029087 MERV 14 Filters 3-Pack Air Filter: MERV-11, Mini Pleat 4023672 6" Motorized Damper Efficiency: 65% ASHRAE Dust Spot 4026859 6" Flex Duct 25' Size: 9" x 11" x 1" 4020128 6" Flex Insulated Duct 25' 4020656 6" Inlet/Exhaust Hood Optional Air Filter: MERV-14, Embossed Pleat (will need filter housing) 4023647 8" Gravity Damper Efficiency: 95% ASHRAE Dust Spot 4020646 8" Butterfly Damper Size: 20" x 24" x 4" 4027415 8" Flex Duct 25' Power Cord: 9', 115 VAC, Ground 4020177 8" Flex Insulated Duct 25' Drain Connection: 3/4"Threaded Female NPT Drain Hose: 8' Direct Gravity Drain Hose (5/8" ID x 7/8" OD) Refrigerant Type: R410A (Refer to manufacturers label for more information) Refrigerant Amount: 15 oz. Dimensions: Unit With Collars Unit Without Collars Shipping Width: 12" 12" 15 5/8" Height: 12" 12" 16" Length: 28" 22" 31 5/8" Weight: 55 lbs. 54 lbs. 65 lbs. ID ID#51102120 #510XXX
Questions? 1-800-533-7533 1-800-533-7533 | www.thermastor.com | www.Ultra-Aire.com Ultra-Aire 70H Installation Options Optional ULTRA-AIRE 70H ATTIC INSTALLATION Heating & A/C Unit Fresh Air 1. The indoor air return should come from an open area on the first Intake Ultra-Aire floor or main level of the home / building. Air Supply 2. The Ultra-Aire supply can be ducted into the forced air system past the air conditioning coil. The duct connection should be Backdraft perpendicular to the air flow. You may also run an independent Damper supply directly from the dehumidifier into a large open room. Indoor Air Return Depending on the application, multiple returns and or supplies may be needed. 3. The optional six inch fresh air intake should be located at least six feet away from any exhaust ports, such as, dryer, range hood, or Motorized combustion device exhaust. Intake location should be consistent Damper with local codes. 4. A section of flex duct or vibration absorbing duct should be located Ultra-Aire between the connections of the Ultra-Aire ductwork and the forced Indoor Air Return air system ductwork. (When ducting into the forced air systems) Indoor Air Supply 5. A back draft damper should be installed when ducting into the forced air system. This prevents counter-flow of the A/C supply air through DEH 3000 the UA 70H. A back draft damper is not needed when ducted control independently. 6. If placed over a finished area, a secondary drip pan is recommended
Ultra-Aire ULTRA-AIRE 70H BASEMENT
Indoor Air OR CRAWLSPACE INSTALLATION Return Heating/AC Return Air 1. Indoor air return should come from an open area of the first or DEH 3000 second floor. control 2. The Ultra-Aire supply should be ducted into the forced air system supply beyond the air conditioning coil. The duct connection should be Backdraft perpendicular to the air flow. Damper 3. An optional eight inch tee fitting with an adjustable blade damper on the straight run may be attached at the Ultra-Aire supply. This allows for increased air flow to the basement/crawlspace during the summer Dry Air to months. Motorized Basement 4. The optional six inch fresh air intake should be located at least six Damper feet away from any exhaust ports, such as, dryer, range hood, or Optional combustion device exhaust. Intake location must be consistent with Fresh Air local codes. Intake Damper 5. A section of flex duct or vibration absorbing duct should be located between the connections of the Ultra-Aire ductwork and the forced air system ductwork. 6. The backdraft damper prevents counter-flow of the A/C supply air through the Ultra-Aire 70H.
Please Note: Therma-Stor does not recommend drawing air from the return ducting system and discharging into the supply, because it could reduce the capacity and may cause potential counterflow through the unit. Preferred installation is to draw air from a separate intake duct located in the central part of the home. Duct the outlet air into the supply duct for distribution throughout the home. A backdraft damper prevents air from the supply duct from being pushed backward through the Ultra-Aire 70Hwhen central (A/C) fan is on and the Ultra-Aire fan is off.
