Chlorobenzene - Methods 2520of 2520production PDF

MANUFACTURING PROCESS
The basic principle behind the manufacture of Chlorobenzene is the

chlorination of benzene with or without the presence of a catalyst (Friedel-Craft
reaction). The products of such a reaction would be Chlorobenzene,
dichlorobenzene, trichlorobenzene and the higher chlorinated benzenes. In
actual practice in the industry, only Chlorobenzene and small amounts of
dichlorobenzene are formed. The amounts of dichlorobenzene and higher
substituted Chlorobenzene formed can be reduced greatly by using selective
catalysts and modifying reaction conditions. Thus essentially chlorination of
benzene can be considered as taking place in three pairs of two stages each:
(1) Chlorination of benzene to monochlorobenzene and dichlorobenzene.
(2) Chlorination of dichlorobenzene to trichlorobenzene and tetrachlorobenzenes.
(3) Chlorination of tetrachlorobenzenes to pentachlorobenzenes and
hexachlorobenzene.
Chlorination can be carried out either batch wise or continuously. When
minimum formation of dichlorobenzenes is required then the latter procedure is
followed. In the batch process, benzene is contained in a deep, iron or steel
vessel, fitted with lead cooling coils. The chlorine feed-pipe enters at the bottom
of the chlorinator and the catalyst is ferric chloride. The temperature is
maintained at less than 45C. HCl produced in the reaction can be recovered
after separation from benzene by washing with a refrigerated solvent. At
temperatures below 40C, the rate of formation of dichlorobenzene is very low
and this fact is used to suppress formation of dichlorobenzene in the continuous
process. A typical continuous process plant consists of a series of small,
externally cooled steel vessels containing the catalyst. Chlorine is supplied to
each vessel through suitably placed inlets and the temperature of the reaction is
maintained between 20 - 40C.
As the Chlorobenzene is formed, it leaves the chlorination zone at a speed

that allows no further chlorination to take place. Unreacted benzene and
Chlorobenzene are continuously separated by fractional distillation, returning
the benzene to the chlorination stage and the efficiency of this process can be as
high as 95%.
There are different ways in which the chlorination of benzene can be
brought about and these form the different processes for the manufacture of
Chlorobenzene. The first is called the Raschig Process. In this process, benzene is
chlorinated by chlorine that has been produced in situ in the reactor by the
catalytic oxidation of hydrogen chloride. A pre-heated mixture of benzene
vapour, air, steam, and HCl, at ordinary pressure, is brought into contact at 220
- 260C with a catalyst of copper oxide. 2% of the total benzene combusts, giving
rise to about one quarter of the total heat output of the process. The disadvantage
of this process is that the high temperature greatly favours high combustion rates
of benzene and the reaction may become uncontrollable. Moreover the high costs
of this vapour phase chlorination process in comparison with other available
processes, allows it to be highly uneconomical for Chlorobenzene manufacture
and thus renders it obsolete. In another process, chlorination of benzene is
carried out in a quartz tube at 400 - 500C. Here the principal product obtained is
Chlorobenzene along with minor amounts of dichlorobenzene. Benzene has also
been chlorinated in the gaseous phase at 425C by means of nitrosylchloride. The
process of Loeser and Schmidt, in which a mixture of benzene vapour, HCl, and
air is reacted at 150 300C in contact with a copper hydroxide-alumina catalyst
(in the form of a fluidised mass), may be regarded as a variant of Raschigs
Process. The disadvantages of all these processes are low efficiency and high
temperature, which may make the reaction uncontrollable leading to formation
of higher Chlorobenzene. Based on all the above considerations, the continuous
liquid phase chlorination of benzene at a temperature of about 40C is best suited
for production of large amounts of monochlorobenzene in the industry.
The process is economically viable too making it the most popular process
being used in the industry for the manufacture of monochlorobenzene all over
the world.
As already known, industrial chlorination of benzene is carried out in the
liquid phase at moderate temperature with the help of a catalyst to produce
monochlorobenzene and minor amounts of dichlorobenzene. Chlorobenzene and
the o- and p-dichlorobenzene are the principal products. The reaction is a
consecutive, competitive reaction. Liquid benzene is fed to a chlorinator
operating at 2.4 bars. The feed enters at 25C, at atmospheric pressure and also
contains some water. Gaseous chlorine is fed to this tank, also at atmospheric
pressure and at 25C and is considered fully pure. There may be several
chlorinators operating in series or parallel depending upon the degree of
chlorination of benzene required. Ferric chloride is usually the catalyst. This can
be added as a solution in benzene, or as iron turnings, or scrap that provides the
ferric chloride in the chlorinator. Since the reaction is exothermic cooling is
required to maintain the temperature at about 40C. The HCl gas (90% of the HCl
formed) leaving the reactor is first cooled to condense the impurities (benzene
and chlorinated products) and then it is scrubbed in a scrubber using refrigerated
Chlorobenzene. The crude chlorobenzene stream leaving the reactor is washed
with NaOH solution (20 wt%; maintained slightly alkaline to protect
downstream equipment from corrosion) in a pre-neutralizer. The product stream
is free of HCl. The product is fed to a Benzene Recovery Column, which is a
distillation column. Here the bottoms are almost 100 % pure chlorobenzene. The
tops contain 98 % by weight of benzene and 2% chlorobenzene and all of the
benzene is recycled to the benzene storage via a purifier. From the purifier the
monochlorobenzene is sent to the refrigeration system. The bottoms from the
Benzene column contain monochlorobenzene and dichlorobenzene. This is fed to
the chlorobenzene column, which is again a distillation column. This may
contain 12 to 20 trays and is operated at a pressure ranging from 37 lb/in.2 abs.
The temperature in the chlorobenzene column may be between 100 - 120C.
Monochlorobenzene is the overhead distillate product of a purity of 99%.
Dichlorobenzene is the bottom residue product of a purity of 97%.
The reactions involved in the process are as follows:

1. C6 H6 + Cl2 D &6H5Cl + HCl
2. C6H5Cl + Cl2 D &6H4Cl2 + HCl
Dichlorobenzene is assumed to be a para-isomer. Formation of trichloro

isomers is neglected. When concentrations of dissolved chlorine remains
essentially constant then reactions are first order.
rb = -k1xb
rm = k1 xb k2 xm k1 = 1 x 10-4 s-1 at 55C
rd = k2 xm k2 = 0.15 x 10-4 s-1 at 55C
Where b = benzene, m = monochlorobenzene, d = dichlorobenzene

Chlorobenzene - Methods 2520of 2520production PDF

Uploaded by

Copyright:

Available Formats

Chlorobenzene - Methods 2520of 2520production PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chlorobenzene - Methods 2520of 2520production PDF

Uploaded by

Copyright:

Available Formats

MANUFACTURING PROCESS

The basic principle behind the manufacture of Chlorobenzene is the

As the Chlorobenzene is formed, it leaves the chlorination zone at a speed

The reactions involved in the process are as follows:

Dichlorobenzene is assumed to be a para-isomer. Formation of trichloro

Where b = benzene, m = monochlorobenzene, d = dichlorobenzene

You might also like