Product Sample & Technical Tools & Support &

Folder Buy Documents Software Community

LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

LM35 Precision Centigrade Temperature Sensors

1 Features 3 Description
•
1 Calibrated Directly in Celsius (Centigrade) The LM35 series are precision integrated-circuit
temperature devices with an output voltage linearly-
• Linear + 10-mV/°C Scale Factor proportional to the Centigrade temperature. The
• 0.5°C Ensured Accuracy (at 25°C) LM35 device has an advantage over linear
• Rated for Full −55°C to 150°C Range temperature sensors calibrated in Kelvin, as the user
• Suitable for Remote Applications is not required to subtract a large constant voltage
from the output to obtain convenient Centigrade
• Low-Cost Due to Wafer-Level Trimming scaling. The LM35 device does not require any
• Operates from 4 V to 30 V external calibration or trimming to provide typical
• Less than 60-μA Current Drain accuracies of ±¼°C at room temperature and ±¾°C
over a full −55°C to 150°C temperature range. Lower
• Low Self-Heating, 0.08°C in Still Air cost is assured by trimming and calibration at the
• Non-Linearity Only ±¼°C Typical wafer level. The low-output impedance, linear output,
• Low-Impedance Output, 0.1 Ω for 1-mA Load and precise inherent calibration of the LM35 device
makes interfacing to readout or control circuitry
2 Applications especially easy. The device is used with single power
supplies, or with plus and minus supplies. As the
• Power Supplies LM35 device draws only 60 μA from the supply, it has
• Battery Management very low self-heating of less than 0.1°C in still air. The
• HVAC LM35 device is rated to operate over a −55°C to
150°C temperature range, while the LM35C device is
• Appliances rated for a −40°C to 110°C range (−10° with
improved accuracy). The LM35-series devices are
available packaged in hermetic TO transistor
packages, while the LM35C, LM35CA, and LM35D
devices are available in the plastic TO-92 transistor
package. The LM35D device is available in an 8-lead
surface-mount small-outline package and a plastic
TO-220 package.

Device Information(1)
PART NUMBER PACKAGE BODY SIZE (NOM)
TO-CAN (3) 4.699 mm × 4.699 mm
TO-92 (3) 4.30 mm × 4.30 mm
LM35
SOIC (8) 4.90 mm × 3.91 mm
TO-220 (3) 14.986 mm × 10.16 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.

Basic Centigrade Temperature Sensor

(2°C to 150°C) Full-Range Centigrade Temperature Sensor
+VS +VS
(4 V to 20 V)

LM35 VOUT
LM35 OUTPUT
0 mV + 10.0 mV/°C
R1

tVS
Choose R1 = –VS / 50 µA
VOUT = 1500 mV at 150°C
VOUT = 250 mV at 25°C
VOUT = –550 mV at –55°C
1

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016 www.ti.com

Table of Contents
1 Features .................................................................. 1 7.3 Feature Description................................................. 13
2 Applications ........................................................... 1 7.4 Device Functional Modes........................................ 13
3 Description ............................................................. 1 8 Application and Implementation ........................ 14
4 Revision History..................................................... 2 8.1 Application Information............................................ 14
8.2 Typical Application .................................................. 15
5 Pin Configuration and Functions ......................... 3
8.3 System Examples ................................................... 16
6 Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4 9 Power Supply Recommendations...................... 19
6.2 ESD Ratings.............................................................. 4 10 Layout................................................................... 19
6.3 Recommended Operating Conditions....................... 4 10.1 Layout Guidelines ................................................. 19
6.4 Thermal Information .................................................. 4 10.2 Layout Example .................................................... 20
6.5 Electrical Characteristics: LM35A, LM35CA Limits... 5 11 Device and Documentation Support ................. 21
6.6 Electrical Characteristics: LM35A, LM35CA ............. 6 11.1 Receiving Notification of Documentation Updates 21
6.7 Electrical Characteristics: LM35, LM35C, LM35D 11.2 Community Resources.......................................... 21
Limits.......................................................................... 8 11.3 Trademarks ........................................................... 21
6.8 Electrical Characteristics: LM35, LM35C, LM35D ... 9 11.4 Electrostatic Discharge Caution ............................ 21
6.9 Typical Characteristics ............................................ 11 11.5 Glossary ................................................................ 21
7 Detailed Description ............................................ 13 12 Mechanical, Packaging, and Orderable
7.1 Overview ................................................................. 13 Information ........................................................... 21
7.2 Functional Block Diagram ....................................... 13

4 Revision History
Changes from Revision F (January 2016) to Revision G Page

• Equation 1, changed From: 10 mV/°F To: 10mv/°C ............................................................................................................ 13

• Power Supply Recommendations, changed From: "4-V to 5.5-V power supply" To: "4-V to 30-V power supply: .............. 19

Changes from Revision E (January 2015) to Revision F Page

• Changed NDV Package (TO-CAN) pinout from Top View to Bottom View ........................................................................... 3

Changes from Revision D (October 2013) to Revision E Page

• Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1

Changes from Revision C (July 2013) to Revision D Page

• Changed W to Ω .................................................................................................................................................................... 1
• Changed W to Ω in Abs Max tablenote. ................................................................................................................................ 4

2 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated

Product Folder Links: LM35

 LM35
www.ti.com SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

5 Pin Configuration and Functions

NDV Package
3-Pin TO-CAN NEB Package
(Bottom View) 3-Pin TO-220
(Top View)

+VS VOUT
t
GND
LM
Case is connected to negative pin (GND) 35DT
D Package
8-PIN SOIC
(Top View)

VOUT 1 8 +VS
N.C. 2 7 N.C.
+VS VOUT
N.C. 3 6 N.C. GND
Tab is connected to the negative pin
GND 4 5 N.C. (GND).
N.C. = No connection NOTE: The LM35DT pinout is different than
the discontinued LM35DP

LP Package
3-Pin TO-92
(Bottom View)

+VS VOUT GND

Pin Functions
PIN
TYPE DESCRIPTION
NAME TO46 TO92 TO220 SO8
VOUT — — — 1 O Temperature Sensor Analog Output
— — — 2
N.C. — No Connection
— — — 3
Device ground pin, connect to power supply negative
GND — — — 4 GROUND
terminal
— — — 5
N.C. — — — 6 — No Connection
— — — 7
+VS — — — 8 POWER Positive power supply pin

Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 3

Product Folder Links: LM35
LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016 www.ti.com

6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN MAX UNIT
Supply voltage –0.2 35 V
Output voltage –1 6 V
Output current 10 mA
Maximum Junction Temperature, TJmax 150 °C
TO-CAN, TO-92 Package –60 150
Storage Temperature, Tstg °C
TO-220, SOIC Package –65 150

(1) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(2) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not
apply when operating the device beyond its rated operating conditions.

6.2 ESD Ratings

VALUE UNIT
V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) ±2500 V

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted)
MIN MAX UNIT
LM35, LM35A –55 150
Specified operating temperature: TMIN to
LM35C, LM35CA –40 110 °C
TMAX
LM35D 0 100
Supply Voltage (+VS) 4 30 V

6.4 Thermal Information

LM35
THERMAL METRIC (1) (2) NDV LP D NEB UNIT
3 PINS 8 PINS 3 PINS
RθJA Junction-to-ambient thermal resistance 400 180 220 90
°C/W
RθJC(top) Junction-to-case (top) thermal resistance 24 — — —

(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
(2) For additional thermal resistance information, see Typical Application.

4 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated

Product Folder Links: LM35

 LM35
www.ti.com SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

6.5 Electrical Characteristics: LM35A, LM35CA Limits

Unless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for the
LM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-Range
Centigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35A LM35CA
PARAMETER TEST CONDITIONS TYP TESTED DESIGN TYP TESTED DESIGN UNIT
LIMIT (1) LIMIT (2) LIMIT (1) LIMIT (2)
TA = 25°C ±0.2 ±0.5 ±0.2 ±0.5
TA = –10°C ±0.3 ±0.3 ±1
Accuracy (3) °C
TA = TMAX ±0.4 ±1 ±0.4 ±1
TA = TMIN ±0.4 ±1 ±0.4 ±1.5
TMIN ≤ TA ≤ TMAX,
Nonlinearity (4) ±0.18 ±0.35 ±0.15 ±0.3 °C
–40°C ≤ TJ ≤ 125°C
Sensor gain TMIN ≤ TA ≤ TMAX 10 9.9 10 9.9
mV/°C
(average slope) –40°C ≤ TJ ≤ 125°C 10 10.1 10 10.1
TA = 25°C ±0.4 ±1 ±0.4 ±1
Load regulation (5)
TMIN ≤ TA ≤ TMAX, mV/mA
0 ≤ IL ≤ 1 mA ±0.5 ±3 ±0.5 ±3
–40°C ≤ TJ ≤ 125°C
TA = 25°C ±0.01 ±0.05 ±0.01 ±0.05
Line regulation (5) 4 V ≤ VS ≤ 30 V, mV/V
±0.02 ±0.1 ±0.02 ±0.1
–40°C ≤ TJ ≤ 125°C
VS = 5 V, 25°C 56 67 56 67
VS = 5 V, –40°C ≤ TJ ≤ 125°C 105 131 91 114
Quiescent current (6) µA
VS = 30 V, 25°C 56.2 68 56.2 68
VS = 30 V, –40°C ≤ TJ ≤ 125°C 105.5 133 91.5 116
4 V ≤ VS ≤ 30 V, 25°C 0.2 1 0.2 1
Change of quiescent
4 V ≤ VS ≤ 30 V, µA
current (5) 0.5 2 0.5 2
–40°C ≤ TJ ≤ 125°C
Temperature
coefficient of –40°C ≤ TJ ≤ 125°C 0.39 0.5 0.39 0.5 µA/°C
quiescent current
Minimum temperature
In circuit of Figure 14, IL = 0 1.5 2 1.5 2 °C
for rate accuracy
Long term stability TJ = TMAX, for 1000 hours ±0.08 ±0.08 °C

(1) Tested Limits are ensured and 100% tested in production.

(2) Design Limits are ensured (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.
(3) Accuracy is defined as the error between the output voltage and 10 mv/°C times the case temperature of the device, at specified
conditions of voltage, current, and temperature (expressed in °C).
(4) Non-linearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the rated
temperature range of the device.
(5) Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.
(6) Quiescent current is defined in the circuit of Figure 14.

Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 5

Product Folder Links: LM35
LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016 www.ti.com

6.6 Electrical Characteristics: LM35A, LM35CA

Unless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for the
LM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-Range
Centigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35A LM35CA
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX TYP TYP MAX
±0.2 ±0.2
(2)
TA = 25°C Tested Limit ±0.5 ±0.5
Design Limit (3)
±0.3 ±0.3
(2)
TA = –10°C Tested Limit
Design Limit (3) ±1
Accuracy (1) °C
±0.4 ±0.4
TA = TMAX Tested Limit (2) ±1 ±1
(3)
Design Limit
±0.4 ±0.4
TA = TMIN Tested Limit (2) ±1
Design Limit (3) ±1.5
±0.18 ±0.15
TMIN ≤ TA ≤ TMAX,
Nonlinearity (4) Tested Limit (2) °C
–40°C ≤ TJ ≤ 125°C
(3)
Design Limit ±0.35 ±0.3
10 10
TMIN ≤ TA ≤ TMAX Tested Limit (2) 9.9
Sensor gain Design Limit (3) 9.9
mV/°C
(average slope) 10 10
–40°C ≤ TJ ≤ 125°C Tested Limit (2) 10.1
Design Limit (3) 10.1
±0.4 ±0.4
TA = 25°C Tested Limit (2) ±1 ±1
Load regulation (5) Design Limit (3)
mV/mA
0 ≤ IL ≤ 1 mA ±0.5 ±0.5
TMIN ≤ TA ≤ TMAX,
Tested Limit (2)
–40°C ≤ TJ ≤ 125°C
Design Limit (3) ±3 ±3
±0.01 ±0.01
TA = 25°C Tested Limit (2) ±0.05 ±0.05
Design Limit (3)
Line regulation (5) mV/V
±0.02 ±0.02
4 V ≤ VS ≤ 30 V,
Tested Limit (2)
–40°C ≤ TJ ≤ 125°C
Design Limit (3) ±0.1 ±0.1

(1) Accuracy is defined as the error between the output voltage and 10 mv/°C times the case temperature of the device, at specified
conditions of voltage, current, and temperature (expressed in °C).
(2) Tested Limits are ensured and 100% tested in production.
(3) Design Limits are ensured (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.
(4) Non-linearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the rated
temperature range of the device.
(5) Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.
6 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated

Product Folder Links: LM35

 LM35
www.ti.com SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

Electrical Characteristics: LM35A, LM35CA (continued)

Unless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for the
LM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-Range
Centigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35A LM35CA
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX TYP TYP MAX
56 56
(2)
VS = 5 V, 25°C Tested Limit 67 67
Design Limit (3)
105 91
VS = 5 V, (2)
Tested Limit
–40°C ≤ TJ ≤ 125°C
Quiescent Design Limit (3) 131 114
µA
current (6) 56.2 56.2
VS = 30 V, 25°C Tested Limit (2) 68 68
Design Limit (3)
105.5 91.5
VS = 30 V,
Tested Limit (2)
–40°C ≤ TJ ≤ 125°C
Design Limit (3) 133 116
0.2 0.2
4 V ≤ VS ≤ 30 V, 25°C Tested Limit (2) 1 1
Change of Design Limit (3)
quiescent µA
current (5) 0.5 0.5
4 V ≤ VS ≤ 30 V,
Tested Limit (2)
–40°C ≤ TJ ≤ 125°C
Design Limit (3) 2 2
0.39 0.39
Temperature
coefficient of –40°C ≤ TJ ≤ 125°C Tested Limit (2) µA/°C
quiescent current
Design Limit (3) 0.5 0.5
1.5 1.5
Minimum
In circuit of Figure 14, IL =
temperature for Tested Limit (2) °C
0
rate accuracy
Design Limit (3) 2 2
Long term ±0.08 ±0.08
TJ = TMAX, for 1000 hours °C
stability

(6) Quiescent current is defined in the circuit of Figure 14.

Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 7

Product Folder Links: LM35
LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016 www.ti.com

6.7 Electrical Characteristics: LM35, LM35C, LM35D Limits

Unless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for the
LM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-Range
Centigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35 LM35C, LM35D
PARAMETER TEST CONDITIONS TYP TESTED DESIGN TYP TESTED DESIGN UNIT
LIMIT (1) LIMIT (2) LIMIT (1) LIMIT (2)
TA = 25°C ±0.4 ±1 ±0.4 ±1
Accuracy, LM35, TA = –10°C ±0.5 ±0.5 ±1.5
°C
LM35C (3) TA = TMAX ±0.8 ±1.5 ±0.8 ±1.5
TA = TMIN ±0.8 ±1.5 ±0.8 ±2
TA = 25°C ±0.6 ±1.5
Accuracy, LM35D (3) TA = TMAX ±0.9 ±2 °C
TA = TMIN ±0.9 ±2
TMIN ≤ TA ≤ TMAX,
Nonlinearity (4) ±0.3 ±0.5 ±0.2 ±0.5 °C
–40°C ≤ TJ ≤ 125°C
TMIN ≤ TA ≤ TMAX,
Sensor gain 10 9.8 10 9.8
–40°C ≤ TJ ≤ 125°C mV/°C
(average slope)
10 10.2 10 10.2
TA = 25°C ±0.4 ±2 ±0.4 ±2
Load regulation (5)
TMIN ≤ TA ≤ TMAX, mV/mA
0 ≤ IL ≤ 1 mA ±0.5 ±5 ±0.5 ±5
–40°C ≤ TJ ≤ 125°C
TA = 25°C ±0.01 ±0.1 ±0.01 ±0.1
Line regulation (5) 4 V ≤ VS ≤ 30 V, mV/V
±0.02 ±0.2 ±0.02 ±0.2
–40°C ≤ TJ ≤ 125°C
VS = 5 V, 25°C 56 80 56 80
VS = 5 V, –40°C ≤ TJ ≤ 125°C 105 158 91 138
Quiescent current (6) µA
VS = 30 V, 25°C 56.2 82 56.2 82
VS = 30 V, –40°C ≤ TJ ≤ 125°C 105.5 161 91.5 141
4 V ≤ VS ≤ 30 V, 25°C 0.2 2 0.2 2
Change of quiescent
4 V ≤ VS ≤ 30 V, µA
current (5) 0.5 3 0.5 3
–40°C ≤ TJ ≤ 125°C
Temperature
coefficient of –40°C ≤ TJ ≤ 125°C 0.39 0.7 0.39 0.7 µA/°C
quiescent current
Minimum temperature
In circuit of Figure 14, IL = 0 1.5 2 1.5 2 °C
for rate accuracy
Long term stability TJ = TMAX, for 1000 hours ±0.08 ±0.08 °C

(1) Tested Limits are ensured and 100% tested in production.

(2) Design Limits are ensured (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.
(3) Accuracy is defined as the error between the output voltage and 10 mv/°C times the case temperature of the device, at specified
conditions of voltage, current, and temperature (expressed in °C).
(4) Non-linearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the rated
temperature range of the device.
(5) Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.
(6) Quiescent current is defined in the circuit of Figure 14.

8 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated

Product Folder Links: LM35

 LM35
www.ti.com SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

6.8 Electrical Characteristics: LM35, LM35C, LM35D

Unless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for the
LM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-Range
Centigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35 LM35C, LM35D
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
±0.4 ±0.4
(2)
TA = 25°C Tested Limit ±1 ±1
Design Limit (3)
±0.5 ±0.5
(2)
TA = –10°C Tested Limit
Accuracy, LM35, Design Limit (3) ±1.5
°C
LM35C (1) ±0.8 ±0.8
TA = TMAX Tested Limit (2) ±1.5
(3)
Design Limit ±1.5
±0.8 ±0.8
TA = TMIN Tested Limit (2)
Design Limit (3) ±1.5 ±2
±0.6
TA = 25°C Tested Limit (2) ±1.5
(3)
Design Limit
±0.9
Accuracy,
TA = TMAX Tested Limit (2) °C
LM35D (1)
Design Limit (3) ±2
±0.9
TA = TMIN Tested Limit (2)
Design Limit (3) ±2
±0.3 ±0.2
TMIN ≤ TA ≤ TMAX,
Nonlinearity (4) Tested Limit (2) °C
–40°C ≤ TJ ≤ 125°C
Design Limit (3) ±0.5 ±0.5
10 10
TMIN ≤ TA ≤ TMAX,
Tested Limit (2) 9.8
–40°C ≤ TJ ≤ 125°C
Sensor gain Design Limit (3) 9.8
mV/°C
(average slope) 10 10
Tested Limit (2) 10.2
Design Limit (3) 10.2
±0.4 ±0.4
TA = 25°C Tested Limit (2) ±2 ±2
Load regulation (5) Design Limit (3)
mV/mA
0 ≤ IL ≤ 1 mA ±0.5 ±0.5
TMIN ≤ TA ≤ TMAX,
Tested Limit (2)
–40°C ≤ TJ ≤ 125°C
Design Limit (3) ±5 ±5

(1) Accuracy is defined as the error between the output voltage and 10 mv/°C times the case temperature of the device, at specified
conditions of voltage, current, and temperature (expressed in °C).
(2) Tested Limits are ensured and 100% tested in production.
(3) Design Limits are ensured (but not 100% production tested) over the indicated temperature and supply voltage ranges. These limits are
not used to calculate outgoing quality levels.
(4) Non-linearity is defined as the deviation of the output-voltage-versus-temperature curve from the best-fit straight line, over the rated
temperature range of the device.
(5) Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output due to heating
effects can be computed by multiplying the internal dissipation by the thermal resistance.
Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM35
LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016 www.ti.com

Electrical Characteristics: LM35, LM35C, LM35D (continued)

Unless otherwise noted, these specifications apply: −55°C ≤ TJ ≤ 150°C for the LM35 and LM35A; −40°C ≤ TJ ≤ 110°C for the
LM35C and LM35CA; and 0°C ≤ TJ ≤ 100°C for the LM35D. VS = 5 Vdc and ILOAD = 50 μA, in the circuit of Full-Range
Centigrade Temperature Sensor. These specifications also apply from 2°C to TMAX in the circuit of Figure 14.
LM35 LM35C, LM35D
PARAMETER TEST CONDITIONS UNIT
MIN TYP MAX MIN TYP MAX
±0.01 ±0.01
(2)
TA = 25°C Tested Limit ±0.1
Design Limit (3) ±0.1
Line regulation (5) mV/V
±0.02 ±0.02
4 V ≤ VS ≤ 30 V,
Tested Limit (2)
–40°C ≤ TJ ≤ 125°C
Design Limit (3) ±0.2 ±0.2
56 56
VS = 5 V, 25°C Tested Limit (2) 80 80
Design Limit (3)
105 91
VS = 5 V, –40°C ≤ TJ ≤
Tested Limit (2)
125°C
Quiescent Design Limit (3) 158 138
µA
current (6) 56.2 56.2
VS = 30 V, 25°C Tested Limit (2) 82 82
(3)
Design Limit
105.5 91.5
VS = 30 V,
Tested Limit (2)
–40°C ≤ TJ ≤ 125°C
Design Limit (3) 161 141
0.2 0.2
4 V ≤ VS ≤ 30 V, 25°C Tested Limit (2) 2
Change of Design Limit (3) 2
quiescent µA
current (5) 0.5 0.5
4 V ≤ VS ≤ 30 V,
Tested Limit (2)
–40°C ≤ TJ ≤ 125°C
Design Limit (3) 3 3
0.39 0.39
Temperature
coefficient of –40°C ≤ TJ ≤ 125°C Tested Limit (2) µA/°C
quiescent current
Design Limit (3) 0.7 0.7
1.5 1.5
Minimum
temperature for In circuit of Figure 14, IL = 0 Tested Limit (2) °C
rate accuracy
Design Limit (3) 2 2
Long term ±0.08 ±0.08
TJ = TMAX, for 1000 hours °C
stability

(6) Quiescent current is defined in the circuit of Figure 14.

10 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated

Product Folder Links: LM35

 LM35
www.ti.com SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

6.9 Typical Characteristics

400 45

40
THERMAL RESISTANCE (ƒC/W)

35

TIME CONSTANT (SEC)

300
30

25
200 T0-46
20

15 T0-46
100
10
T0-92
5
T0-92
0 0
0 400 800 1200 1600 2000 0 400 800 1200 1600 2000
AIR VELOCITY (FPM) C001 AIR VELOCITY (FPM) C002

Figure 1. Thermal Resistance Junction To Air Figure 2. Thermal Time Constant

120 120
PERCENT OF FINAL VALUE (%)

PERCENT OF FINAL VALUE (%)

100 100

80 80 T0-46

60 60
T0-92
40 40

20 20

0 0

±20 ±20
0 2 4 6 8 0 2 4 6 8
TIME (MINUTES) C003 TIME (SEC) C004

Figure 3. Thermal Response In Still Air Figure 4. Thermal Response In Stirred Oil Bath
4.4 160
4.2 TYPICAL 140
QUIESCENT CURRENT ( A)

4.0 IOUT = 2.0 mA

SUPPLY VOLTAGE (V)

120
3.8
3.6 100

3.4 80
TYPICAL
3.2 IOUT = 1.0 mA 60
3.0
40
2.8 TYPICAL
IOUT = 0 A or 50 A
2.6 20

2.4 0
±75 ±25 25 75 125 175 ±75 ±25 25 75 125 175
TEMPERATURE (ƒC) C005 TEMPERATURE (ƒC) C006

Figure 5. Minimum Supply Voltage vs Temperature Figure 6. Quiescent Current vs Temperature (in Circuit of
Figure 14)

Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 11

Product Folder Links: LM35
LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016 www.ti.com

Typical Characteristics (continued)

200 2.0

180 1.5 LM35

TEMPERATURE ERROR (ƒC)

QUIESCENT CURRENT ( A)

160 1.0

140 0.5 LM35A

TYPICAL
120 0.0

100 ±0.5 LM35A

80 ±1.0

60 ±1.5
LM35
40 ±2.0
±75 ±25 25 75 125 175 ±75 ±25 25 75 125 175
TEMPERATURE (ƒC) C007 TEMPERATURE (ƒC) C008

Figure 7. Quiescent Current vs Temperature (in Circuit of Figure 8. Accuracy vs Temperature (Ensured)
Full-Range Centigrade Temperature Sensor)
2.5 1600

2.0 LM35D
1400
TEMPERATURE ERROR (ƒC)

1.5 LM35C
1200
1.0

Noise (nV/—Hz)
LM35CA 1000
0.5
TYPICAL
0.0 800

±0.5 600
LM35CA
±1.0
400
±1.5 LM35C
200
±2.0
±2.5 0
±75 ±25 25 75 125 175 10 100 1k 10k 100k
TEMPERATURE (ƒC) C009
FREQUENCY (Hz) C010

Figure 9. Accuracy vs Temperature (Ensured) Figure 10. Noise Voltage

6
VIN (V)

0.6

0.4
VOUT (V)

0.2

-0.2
-20 -10 0 10 20 30 40 50 60
TIME ( SEC) C011

Figure 11. Start-Up Response

12 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated

Product Folder Links: LM35

 LM35
www.ti.com SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

7 Detailed Description

7.1 Overview
The LM35-series devices are precision integrated-circuit temperature sensors, with an output voltage linearly
proportional to the Centigrade temperature. The LM35 device has an advantage over linear temperature sensors
calibrated in Kelvin, as the user is not required to subtract a large constant voltage from the output to obtain
convenient Centigrade scaling. The LM35 device does not require any external calibration or trimming to provide
typical accuracies of ± ¼ °C at room temperature and ± ¾ °C over a full −55°C to 150°C temperature range.
Lower cost is assured by trimming and calibration at the wafer level. The low output impedance, linear output,
and precise inherent calibration of the LM35 device makes interfacing to readout or control circuitry especially
easy. The device is used with single power supplies, or with plus and minus supplies. As the LM35 device draws
only 60 μA from the supply, it has very low self-heating of less than 0.1°C in still air. The LM35 device is rated to
operate over a −55°C to 150°C temperature range, while the LM35C device is rated for a −40°C to 110°C range
(−10° with improved accuracy). The temperature-sensing element is comprised of a delta-V BE architecture.
The temperature-sensing element is then buffered by an amplifier and provided to the VOUT pin. The amplifier
has a simple class A output stage with typical 0.5-Ω output impedance as shown in the Functional Block
Diagram. Therefore the LM35 can only source current and it's sinking capability is limited to 1 μA.

7.2 Functional Block Diagram

A1

1.38 VPTAT

+VS
nR1
Q1 Q2 +
A2
10E E
VOUT = 10 mV/°C
V0
.125 R2
nR1
8.8 mV/°C
i R2

7.3 Feature Description

7.3.1 LM35 Transfer Function
The accuracy specifications of the LM35 are given with respect to a simple linear transfer function:
VOUT = 10 mv/°C × T
where
• VOUT is the LM35 output voltage
• T is the temperature in °C (1)

7.4 Device Functional Modes

The only functional mode of the LM35 is that it has an analog output directly proportional to temperature.

Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 13

Product Folder Links: LM35
LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016 www.ti.com

8 Application and Implementation

NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.

8.1 Application Information

The features of the LM35 make it suitable for many general temperature sensing applications. Multiple package
options expand on it's flexibility.

8.1.1 Capacitive Drive Capability

Like most micropower circuits, the LM35 device has a limited ability to drive heavy capacitive loads. Alone, the
LM35 device is able to drive 50 pF without special precautions. If heavier loads are anticipated, isolating or
decoupling the load with a resistor is easy (see Figure 12). The tolerance of capacitance can be improved with a
series R-C damper from output to ground (see Figure 13).
When the LM35 device is applied with a 200-Ω load resistor as shown in Figure 16, Figure 17, or Figure 19, the
device is relatively immune to wiring capacitance because the capacitance forms a bypass from ground to input
and not on the output. However, as with any linear circuit connected to wires in a hostile environment,
performance is affected adversely by intense electromagnetic sources (such as relays, radio transmitters, motors
with arcing brushes, and SCR transients), because the wiring acts as a receiving antenna and the internal
junctions act as rectifiers. For best results in such cases, a bypass capacitor from VIN to ground and a series R-C
damper, such as 75 Ω in series with 0.2 or 1 μF from output to ground, are often useful. Examples are shown in
Figure 13, Figure 24, and Figure 25.

+ HEAVY CAPACITIVE LOAD, WIRING, ETC.

2k
LM35 TO A HIGH-IMPEDANCE LOAD
OUT
v

Figure 12. LM35 with Decoupling from Capacitive Load

+ HEAVY CAPACITIVE LOAD, WIRING, ETC.

OUT
LM35 TO A HIGH-IMPEDANCE LOAD
0.01 PF BYPASS
OPTONAL v 75

1 PF

Figure 13. LM35 with R-C Damper

14 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated

Product Folder Links: LM35

 LM35
www.ti.com SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

8.2 Typical Application

8.2.1 Basic Centigrade Temperature Sensor
+VS
(4 V to 20 V)

LM35 OUTPUT
0 mV + 10.0 mV/°C

Figure 14. Basic Centigrade Temperature Sensor (2 °C to 150 °C)

8.2.1.1 Design Requirements

Table 1. Design Parameters

PARAMETER VALUE
Accuracy at 25°C ±0.5°C
Accuracy from –55 °C to 150°C ±1°C
Temperature Slope 10 mV/°C

8.2.1.2 Detailed Design Procedure

Because the LM35 device is a simple temperature sensor that provides an analog output, design requirements
related to layout are more important than electrical requirements. For a detailed description, refer to the Layout.

8.2.1.3 Application Curve

2.0

1.5 LM35
TEMPERATURE ERROR (ƒC)

1.0

0.5 LM35A
TYPICAL
0.0

±0.5 LM35A

±1.0

±1.5
LM35
±2.0
±75 ±25 25 75 125 175
TEMPERATURE (ƒC) C008

Figure 15. Accuracy vs Temperature (Ensured)

Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 15

Product Folder Links: LM35
LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016 www.ti.com

8.3 System Examples

5V 5V
+
+
OUT
HEAT LM35
VOUT = 10 mV/°C (TAMBIENT = 1 °C) FINS TWISTED PAIR
6.8 k 200 FROM + 2 °C TO + 40 °C v 200
5% 1% 1%
v VOUT = 10 mV/°C (TAMBIENT = 1 °C)
FROM + 2 °C TO + 40 °C
+
6.8 k
OUT 5% 200
HEAT LM35
FINS OR 10K RHEOSTAT 1%
TWISTED PAIR
v 200 FOR GAIN ADJUST
1%

Figure 16. Two-Wire Remote Temperature Sensor Figure 17. Two-Wire Remote Temperature Sensor
(Grounded Sensor) (Output Referred to Ground)
+VS +
5V

OUT
0.01 PF LM35
BYPASS TWISTED PAIR
OPTIONAL
2k 200
LM35 + 1% 1%
VOUT = 10 mV/°C (TAMBIENT = 10 °C)
VOUT FROM t 5 °C TO + 40 °C
2k 200
v 1% 1%

1N914
18 k
10%

Figure 18. Temperature Sensor, Single Supply Figure 19. Two-Wire Remote Temperature Sensor
(−55° to +150°C) (Output Referred to Ground)

16 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated

Product Folder Links: LM35

 LM35
www.ti.com SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

System Examples (continued)

+ 5 V TO + 30 V +VS
(6 V to 20 V)
4.7 k

2N2907 LM35
+ IN
45.5 kO
OUT OUT
LM35 LM317 1%

v 402 ADJ
1%
62.5 10 kO
0.5% OFFSET 1%
ADJUST 50 VOUT = +1 mV/°F
26.4 kO
1%

LM385-1.2 18 kO

1 MO
1%

Figure 20. 4-To-20 mA Current Source Figure 21. Fahrenheit Thermometer

(0°C to 100°C)
5V 9V

1k
LM35 LM35
100 A,
60 mV
FULL-
SCALE

LM385- 25.5 k
2.5

Figure 22. Centigrade Thermometer Figure 23. Fahrenheit Thermometer, Expanded

(Analog Meter) Scale Thermometer
(50°F to 80°F, for Example Shown)

Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 17

Product Folder Links: LM35
LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016 www.ti.com

System Examples (continued)

5V 5V

+ 3.9 k + 16 k
PARALLEL
OUT IN OUT IN 8
LM35 SERIAL LM35 DATA
REF ADC08031 OUTPUT
DATA OUTPUT
1.28 V
GND GND ADC0804
75 100k 75 INTR
+
CLOCK 1k + VREF
FB LM385 0.64 V
+ ENABLE CS
1 PF 10 k +
1 PF 2k RD
GND WR
GND

Figure 24. Temperature to Digital Converter Figure 25. Temperature to Digital Converter
(Serial Output) (Parallel TRI-STATE Outputs for Standard Data Bus
(128°C Full Scale) to μP Interface)
(128°C Full Scale)
°F 6V

20 k 6.8 k 1k
67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86
7V
+
20 PF
fOUT
20 LEDs 4N28
18 10 18 10 +
100 k 8
LM3914 LM3914
LM35 7 5
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 LM131
NC GND 6 3
7V 7V
1.2 k*
+ VA 1 2 4
OUT 0.01 PF 12 k 0.01 PF
HEAT LM35 100 k 1 PF FULL
FINS VC VB SCALE
200* 499* 499* ADJ

1.5 k* 1 k*
5k LOW TEMPCO
47
+ RB
1 PF 1.5 k* RC
1k 1k

RA
1k

*=1% or 2% film resistor

Trim RB for VB = 3.075 V
Trim RC for VC = 1.955 V
Trim RA for VA = 0.075 V + 100 mV/°C ×Tambient
Example, VA = 2.275 V at 22°C
Figure 26. Bar-Graph Temperature Display Figure 27. LM35 With Voltage-To-Frequency
(Dot Mode) Converter and Isolated Output
(2°C to 150°C; 20 to 1500 Hz)

18 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated

Product Folder Links: LM35

 LM35
www.ti.com SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

9 Power Supply Recommendations

The LM35 device has a very wide 4-V to 30-V power supply voltage range, which makes it ideal for many
applications. In noisy environments, TI recommends adding a 0.1 μF from V+ to GND to bypass the power
supply voltage. Larger capacitances maybe required and are dependent on the power-supply noise.

10 Layout

10.1 Layout Guidelines

The LM35 is easily applied in the same way as other integrated-circuit temperature sensors. Glue or cement the
device to a surface and the temperature should be within about 0.01°C of the surface temperature.
The 0.01°C proximity presumes that the ambient air temperature is almost the same as the surface temperature.
If the air temperature were much higher or lower than the surface temperature, the actual temperature of the
LM35 die would be at an intermediate temperature between the surface temperature and the air temperature;
this is especially true for the TO-92 plastic package. The copper leads in the TO-92 package are the principal
thermal path to carry heat into the device, so its temperature might be closer to the air temperature than to the
surface temperature.
Ensure that the wiring leaving the LM35 device is held at the same temperature as the surface of interest to
minimize the temperature problem. The easiest fix is to cover up these wires with a bead of epoxy. The epoxy
bead will ensure that the leads and wires are all at the same temperature as the surface, and that the
temperature of the LM35 die is not affected by the air temperature.
The TO-46 metal package can also be soldered to a metal surface or pipe without damage. Of course, in that
case the V− terminal of the circuit will be grounded to that metal. Alternatively, mount the LM35 inside a sealed-
end metal tube, and then dip into a bath or screw into a threaded hole in a tank. As with any IC, the LM35 device
and accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is
especially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuit
coatings and varnishes such as a conformal coating and epoxy paints or dips are often used to insure that
moisture cannot corrode the LM35 device or its connections.
These devices are sometimes soldered to a small light-weight heat fin to decrease the thermal time constant and
speed up the response in slowly-moving air. On the other hand, a small thermal mass may be added to the
sensor, to give the steadiest reading despite small deviations in the air temperature.

Table 2. Temperature Rise of LM35 Due To Self-heating (Thermal Resistance, RθJA)

SOIC-8 (2),
TO, no heat TO (1), small TO-92, no heat TO-92 (2), small SOIC-8, no TO-220, no
small heat
sink heat fin sink heat fin heat sink heat sink
fin
Still air 400°C/W 100°C/W 180°C/W 140°C/W 220°C/W 110°C/W 90°C/W
Moving air 100°C/W 40°C/W 90°C/W 70°C/W 105°C/W 90°C/W 26°C/W
Still oil 100°C/W 40°C/W 90°C/W 70°C/W — — —
Stirred oil 50°C/W 30°C/W 45°C/W 40°C/W — — —
(Clamped to
metal, Infinite (24°C/W) — — (55°C/W) —
heat sink)

(1) Wakefield type 201, or 1-in disc of 0.02-in sheet brass, soldered to case, or similar.
(2) TO-92 and SOIC-8 packages glued and leads soldered to 1-in square of 1/16-in printed circuit board with 2-oz foil or similar.

Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 19

Product Folder Links: LM35
LM35
SNIS159G – AUGUST 1999 – REVISED AUGUST 2016 www.ti.com

10.2 Layout Example

VIA to ground plane

VIA to power plane

VOUT +VS

N.C. N.C. 0.01 µF

N.C. N.C.

GND N.C.

Figure 28. Layout Example

20 Submit Documentation Feedback Copyright © 1999–2016, Texas Instruments Incorporated

Product Folder Links: LM35

 LM35
www.ti.com SNIS159G – AUGUST 1999 – REVISED AUGUST 2016

11 Device and Documentation Support

11.1 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document

11.2 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.

11.3 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.

11.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.

12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

Copyright © 1999–2016, Texas Instruments Incorporated Submit Documentation Feedback 21

Product Folder Links: LM35
 PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)

LM35AH ACTIVE TO NDV 3 500 TBD Call TI Call TI -55 to 150 ( LM35AH ~ LM35AH)

LM35AH/NOPB ACTIVE TO NDV 3 500 Green (RoHS Call TI Level-1-NA-UNLIM -55 to 150 ( LM35AH ~ LM35AH)
& no Sb/Br)
LM35CAH ACTIVE TO NDV 3 500 TBD Call TI Call TI -40 to 110 ( LM35CAH ~
LM35CAH)
LM35CAH/NOPB ACTIVE TO NDV 3 500 Green (RoHS Call TI Level-1-NA-UNLIM -40 to 110 ( LM35CAH ~
& no Sb/Br) LM35CAH)
LM35CAZ/LFT4 ACTIVE TO-92 LP 3 2000 Green (RoHS CU SN N / A for Pkg Type LM35
& no Sb/Br) CAZ
LM35CAZ/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS CU SN N / A for Pkg Type -40 to 110 LM35
& no Sb/Br) CAZ
LM35CH ACTIVE TO NDV 3 500 TBD Call TI Call TI -40 to 110 ( LM35CH ~ LM35CH)

LM35CH/NOPB ACTIVE TO NDV 3 500 Green (RoHS Call TI Level-1-NA-UNLIM -40 to 110 ( LM35CH ~ LM35CH)
& no Sb/Br)
LM35CZ/LFT1 ACTIVE TO-92 LP 3 2000 Green (RoHS CU SN N / A for Pkg Type LM35
& no Sb/Br) CZ
LM35CZ/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS CU SN N / A for Pkg Type -40 to 110 LM35
& no Sb/Br) CZ
LM35DH ACTIVE TO NDV 3 1000 TBD Call TI Call TI 0 to 70 ( LM35DH ~ LM35DH)

LM35DH/NOPB ACTIVE TO NDV 3 1000 Green (RoHS Call TI | POST-PLATE Level-1-NA-UNLIM 0 to 70 ( LM35DH ~ LM35DH)
& no Sb/Br)
LM35DM NRND SOIC D 8 95 TBD Call TI Call TI 0 to 100 LM35D
M
LM35DM/NOPB ACTIVE SOIC D 8 95 Green (RoHS CU SN Level-1-260C-UNLIM 0 to 100 LM35D
& no Sb/Br) M
LM35DMX NRND SOIC D 8 2500 TBD Call TI Call TI 0 to 100 LM35D
M
LM35DMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS CU SN Level-1-260C-UNLIM 0 to 100 LM35D
& no Sb/Br) M
LM35DT NRND TO-220 NEB 3 45 TBD Call TI Call TI 0 to 100 LM35DT
LM35DT/NOPB ACTIVE TO-220 NEB 3 45 Green (RoHS CU SN Level-1-NA-UNLIM 0 to 100 LM35DT
& no Sb/Br)

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)

LM35DZ/LFT1 ACTIVE TO-92 LP 3 2000 Green (RoHS CU SN N / A for Pkg Type LM35
& no Sb/Br) DZ
LM35DZ/LFT4 ACTIVE TO-92 LP 3 2000 Green (RoHS CU SN N / A for Pkg Type LM35
& no Sb/Br) DZ
LM35DZ/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS CU SN N / A for Pkg Type 0 to 100 LM35
& no Sb/Br) DZ
LM35H ACTIVE TO NDV 3 500 TBD Call TI Call TI -55 to 150 ( LM35H ~ LM35H)

LM35H/NOPB ACTIVE TO NDV 3 500 Green (RoHS Call TI Level-1-NA-UNLIM -55 to 150 ( LM35H ~ LM35H)
& no Sb/Br)

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)

(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.

(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.

Addendum-Page 2
 PACKAGE OPTION ADDENDUM

www.ti.com 17-Mar-2017

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

Addendum-Page 3
 PACKAGE MATERIALS INFORMATION

www.ti.com 15-Aug-2016

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM35DMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1
LM35DMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 15-Aug-2016

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM35DMX SOIC D 8 2500 367.0 367.0 35.0
LM35DMX/NOPB SOIC D 8 2500 367.0 367.0 35.0

Pack Materials-Page 2
 PACKAGE OUTLINE
NDV0003H SCALE 1.250
TO-CAN - 2.67 mm max height
TO-46

4.95
4.55

0.76 MAX 2.67 MAX

0.64 MAX
UNCONTROLLED
LEAD DIA

3X
12.7 MIN

0.483
3X
0.407

5.32-5.56
2

1 3

45
( 2.54)
1.16
0.92
1.22
0.72

4219876/A 01/2017

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Reference JEDEC registration TO-46.

www.ti.com
 EXAMPLE BOARD LAYOUT
NDV0003H TO-CAN - 2.67 mm max height
TO-46

(2.54)

0.07 MAX ( 1.2)

ALL AROUND METAL
3
3X ( 0.7) VIA

SOLDER MASK
OPENING
(1.27)
1
(R0.05) TYP

2X ( 1.2)
2 METAL
0.07 MAX
TYP 2X
SOLDER MASK
OPENING

LAND PATTERN EXAMPLE

NON-SOLDER MASK DEFINED
SCALE:12X

4219876/A 01/2017

www.ti.com
 PACKAGE OUTLINE
LP0003A SCALE 1.200 SCALE 1.200
TO-92 - 5.34 mm max height
TO-92

5.21
4.44

EJECTOR PIN
OPTIONAL
5.34
4.32

(1.5) TYP

(2.54) SEATING
2X NOTE 3 PLANE
4 MAX
(0.51) TYP
6X
0.076 MAX
SEATING
PLANE
3X
12.7 MIN

0.43
2X 0.55 3X
3X 0.35
2.6 0.2 0.38
2X 1.27 0.13
FORMED LEAD OPTION
OTHER DIMENSIONS IDENTICAL STRAIGHT LEAD OPTION
TO STRAIGHT LEAD OPTION

2.67
3X
2.03 4.19
3.17
3 2 1

3.43 MIN

4215214/B 04/2017

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Lead dimensions are not controlled within this area.
4. Reference JEDEC TO-226, variation AA.
5. Shipping method:
a. Straight lead option available in bulk pack only.
b. Formed lead option available in tape and reel or ammo pack.
c. Specific products can be offered in limited combinations of shipping medium and lead options.
d. Consult product folder for more information on available options.

www.ti.com
 EXAMPLE BOARD LAYOUT
LP0003A TO-92 - 5.34 mm max height
TO-92

FULL R
0.05 MAX (1.07) TYP
ALL AROUND METAL 3X ( 0.85) HOLE
TYP TYP

2X
METAL
(1.5) 2X (1.5)

2X
SOLDER MASK
OPENING
1 2 3
(R0.05) TYP 2X (1.07)
(1.27)
SOLDER MASK
(2.54)
OPENING

LAND PATTERN EXAMPLE

STRAIGHT LEAD OPTION
NON-SOLDER MASK DEFINED
SCALE:15X

0.05 MAX ( 1.4) 2X ( 1.4)

ALL AROUND METAL
TYP 3X ( 0.9) HOLE

METAL

2X
1 2 3 SOLDER MASK
(R0.05) TYP
(2.6) OPENING
SOLDER MASK
OPENING (5.2)

LAND PATTERN EXAMPLE

FORMED LEAD OPTION
NON-SOLDER MASK DEFINED
SCALE:15X

4215214/B 04/2017

www.ti.com
 TAPE SPECIFICATIONS
LP0003A TO-92 - 5.34 mm max height
TO-92

13.7
11.7

32
23

(2.5) TYP 0.5 MIN

16.5
15.5

11.0 9.75
8.5 8.50

19.0
17.5

2.9 6.75 3.7-4.3 TYP

TYP
2.4 5.95
13.0
12.4

FOR FORMED LEAD OPTION PACKAGE

4215214/B 04/2017

www.ti.com
 IMPORTANT NOTICE

Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2017, Texas Instruments Incorporated