Obsolete Product(s) - Obsolete Product(s) : Hex Precision Limiter
Obsolete Product(s) - Obsolete Product(s) : Hex Precision Limiter
Obsolete Product(s) - Obsolete Product(s) : Hex Precision Limiter
.. VOLTAGE
FAST ACTIVE CLAMPING
d u
r o
e P
DESCRIPTION
The L9700 is a monolithic circuit which is suited for
l e t
MINIDIP SO8
c t
Very fast speed is achieved by internal feedback
and the application of a new vertical PNP-transistor
with isolated collector.
d u
BLOCK DIAGRAM r o
e P
l e t
s o
O b
September 2000 1
This is advanced information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
L9700
THERMAL DATA
( s ) C/W
u ct
PIN CONNECTION
o d
P r
e te
o l
b s
- O
(s )
c t
d u
r o
ELECTRICAL CHARACTERISTICS (VCC = 5V, TJ = 40 to 125C unless otherwise specified)
Symbol
e P
Parameter Test condition Min. Typ. Max. Unit
VCC
ICC
l e t
Supply Voltage
Supply Current
4.75
1.5
5.25
3
V
mA
s
Vcis
o
Static Input Clamping Voltage Negative IIN = 10mA 250 0 mV
(*) Design limits are guaranteed by statistical control on production samples over the indicated temperature and supply voltage
ranges. These limits are not used to calculate outgoing quality levels.
2/8
L9700
( s )
u ct
o d
P r
e t e
o l
Figure 2 : Dynamical Input Characteristics.
b s
2a
- O
(s )
c t
d u
r o
e P
l e t
s o
O b
3/8
L9700
( s )
u ct
o d
P r
e t e
o l
APPLICATION INFORMATION
b s
Most integrated circuits, both HNMOS and bipolar, O clamp and a low current leakage providing the opti-
c t
These transients occur in large numbers and with The high intervention speed, due to the pre-bias of
d u
different magnitudes in the automotive environment,
making adequate protection for devices ai-med at it
the limiter stage and internal feedback, limits the
voltage overshoot and avoid the use of external ca-
indispensible.
r o pacitors for the limitation of the transient rise times.
P
Overvoltages on the supply line are faced through
high voltage integration technologies or through ex-
e
Figure 3 illustrates a typical automotive application
l e t
ternal protection (transil, varistor).
Signal inputs are generally protected using clamp
scheme. The resistor RS limits the input current of
the device and is therefore dimensioned considering
o
diodes to the supply and ground, and a current limi-
s
the characteristics of the transients to be eliminated.
Consequently :
O b
ter resistor. However, such solutions do not always
completely satisfy the protection specifications in
terms of intervention speed, negative clamping and RS =
Vtransient Peak
current leakage high enough to change analog si- IIN MAX
gnals. The CIN capacitors must be used only on analog in-
The L9700 device combines a high intervention puts because they present a low impedance during
speed with a high precision positive and negative the sampling period.
4/8
L9700
( s )
u ct
o d
P r
e t e
o l
The minimum value for CIN is determined by the ac-
b
buts Q1 = CIN VIN
curacy required, the time taken to sample the input
-
and the input impedance during that time, while the Oand Q1 Q2 = ID TS
c t
Thus for a resistive input A/D connector where :
100
ID TS
TS = Sample time (Seconds)
d u and CIN (min) =
VIN k
Farad
o
RD = Device input resistance (Ohms)
r
VIN = Input voltage (Volts) so CIN (min) =
100 TS
k RD
Farad
e P
k = Required accuracy (%)
let
The calculation for a sample and hold type convertor
Q1 = Charge on capacitor before sampling is even simpler :
s o
Q2 = Charge on capacitor after sampling
ID = Device input current (Amps)
k = Required accuracy (%)
Ob
Thus :
k Q1
CH = Hold capacitor (Farad)
100 CH
Q1 Q2 = CIN (min) = Farad
100 k
5/8
L9700
mm inch
DIM. OUTLINE AND
MIN. TYP. MAX. MIN. TYP. MAX. MECHANICAL DATA
A 3.32 0.131
a1 0.51 0.020
D 10.92 0.430
( s )
ct
E 7.95 9.75 0.313 0.384
e 2.54 0.100
d u
e3 7.62 0.300
r o
e4 7.62 0.300
e P
F 6.6 0.260
l e t
I 5.08 0.200
so
L
Z
3.18 3.81
1.52
0.125 0.150
0.060
O b Minidip
) -
c t (s
d u
r o
e P
l e t
s o
O b
6/8
L9700
mm inch
DIM. OUTLINE AND
MIN. TYP. MAX. MIN. TYP. MAX.
MECHANICAL DATA
A 1.75 0.069
a1 0.1 0.25 0.004 0.010
a2 1.65 0.065
a3 0.65 0.85 0.026 0.033
b 0.35 0.48 0.014 0.019
b1 0.19 0.25 0.007 0.010
C 0.25 0.5 0.010 0.020
c1 45 (typ.)
( s )
ct
D (1) 4.8 5.0 0.189 0.197
E 5.8 6.2 0.228 0.244
d u
e 1.27 0.050
ro
P
e3 3.81 0.150
F (1)
L
3.8
0.4
4.0
1.27
0.15
0.016
0.157
0.050
e te
M 0.6 0.024
o l SO8
S 8 (max.)
b s
(1) D and F do not include mold flash or protrusions. Mold flash or
potrusions shall not exceed 0.15mm (.006inch).
- O
(s )
c t
d u
r o
e P
l e t
s o
O b
7/8
L9700
( s )
u ct
o d
P r
e t e
o l
b s
- O
(s )
c t
d u
r o
e P
l e t
s o
O b
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the conse-
quences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No
license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this
publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMi-
croelectronics products are not authorized for use as critical components in life support devices or systems without express written
approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
2000 STMicroelectronics Printed in Italy All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco -
Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A.
http://www.st.com
8/8