D4B802B7E7F Electrical System

Service
Workshop Manual
Octavia III 2013
Octavia III 2014
Electrical system
Edition 12.2014
Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
unless authorised by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
with respect to the correctness of information in this document. Copyright by KODA AUTO A. S.
Service Department. Technical Information

Service
List of Workshop Manual Repair GroupsList of Workshop Manual
Repair GroupsList of Workshop Manual Repair Groups
Repair Group
27 - Starter, current supply, CCS
90 - Gauges, instruments
91 - Communication
92 - Windscreen wash/wipe system
94 - Lights, bulbs, switches - exterior
96 - Lights, bulbs, switches - interior
97 - Wiring
Technical information should always be available to the foremen and mechanics, because their
careful and constant adherence to the instructions is essential to ensure vehicle road-worthiness and
safety. In addition, the normal basic safety precautions for working on motor vehicles must, as a
matter of course, be observed.
All rights reserved.

No reproduction without prior agreement from publisher.
Copyright 2014 KODA AUTO a. s. D4B802B7E7F

Octavia III 2013 , Octavia III 2014
Electrical system - Edition 12.2014
Contents
27 - Starter, current supply, CCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1 Contact corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.1 Basics, battery types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2.2 Warning instructions and safety precautions when working on the battery . . . . . . . . . . . . 2
2.3 Work sequence when disconnecting and connecting the battery . . . . . . . . . . . . . . . . . . . . 2
2.4 Checking battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.5 Charging battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.6 Removing and installing battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.7 Removing and installing battery tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.8 Battery parameterisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1 Removing and installing starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4 Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Checking generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.2 Removing and installing alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.3 Fixing the B+ wire to the AC generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4.4 Checking the carbon brushes of the AC generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.5 Removing and installing the Bosch voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.6 Removing and installing the Valeo voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.7 Removing and installing the V-ribbed belt pulley on the AC generator . . . . . . . . . . . . . . . . 14
4.8 Removing and installing the V-ribbed belt pulley with free wheel . . . . . . . . . . . . . . . . . . . . 15
5 Start-stop system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Safety precautions for vehicles with start-stop system . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.3 Fault recognition and fault display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.4 Battery recharging or starting by external source on vehicles with battery monitoring control
unit J367 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.5 Replacing the battery on vehicles with battery monitoring control unit J367 . . . . . . . . . . . . 17
5.6 Battery monitoring control unit J367 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.7 Button for start-stop system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6 Cruise control system (CCS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7 Automatic distance control (adapted CC) and Front Assist . . . . . . . . . . . . . . . . . . . . . . . . 20
7.2 Overview of the fitting positions: Automatic distance control, Front Assist . . . . . . . . . . . . 20
7.3 Removing and installing the clearance control control unit J428 . . . . . . . . . . . . . . . . . . . . 22
7.4 Removing
unless authorised by KODAandAUTO
installing retaining
A. S. KODA AUTO A. S.plate forguarantee
does not clearance
or acceptcontrol control unit J428 . . . . . . . .
any liability 22
7.5 with respect
Calibrate automatic distance control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
to the correctness of information in this document. Copyright by KODA AUTO A. S.
23
90 - Gauges, instruments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1 Dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.2 Adjust/replace dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.3 Removing and installing dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.4 Warning lights in the dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.5 The self-diagnostic function of the dash panel insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
91 - Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1 Multimedia information system Infotainment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1.1 General points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
1.2 Installation Infotainment system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
1.3 Infotainment summary of components with radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Contents i
1.4 Infotainment summary of components with navigation . . . . . . . . . . . . . . . . . . . . . . . . . . 32

1.5 Electronic anti-theft coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
1.6 Removing and installing the Infotainment display/control unit . . . . . . . . . . . . . . . . . . . . . . 33
1.7 Infotainment self-diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2 Aerial systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2.1 Overview of the aerial systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2.2 Removing and installing the roof aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2.3 Removing and installing frequency filters for frequency modulation (FM) in the positive cable
R179 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.4 Removing and installing frequency filters for frequency modulation (FM) in the positive cable
R178 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
2.5 Removing and installing AM/FM, FM2/DAB aerial module (amplifier) . . . . . . . . . . . . . . . . 41
2.6 Replacing aerial cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3 Telephone system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.1 General Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.2 Summary of components telephone system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.3 Removing and installing the aerial signal reception amplifier (compensor) . . . . . . . . . . . . 44
3.4 Removing and installing induction plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.5 Check induction plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.6 Removing and installing the microphone for the telephone R38 . . . . . . . . . . . . . . . . . . . . 46
4 Multi-functional steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.2 Removing and installing the Infotainment switch units . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.3 Removing and installing switch units for gearbox operation in Tiptronic mode (gearbox 02E,
0AM DSG) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
4.4 Self-diagnosis of the multi-functional steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5 Canton sound system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.1 Fitting position overview sound system components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.2 Removing and installing the sound system control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
5.3 Self-diagnosis of the equipment Sound system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
6 Removing and installing loudspeakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.1 Removing and installing the front and rear mid-bass speaker . . . . . . . . . . . . . . . . . . . . . . 52
6.2 Removing and installing front treble loudspeakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.3 Removing and installing the rear treble speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.4 Removing and installing the central speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6.5 Removing and installing subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
7 Connections for audio/video signal MEDIA IN (multimedia socket) external source . . . . . . 54
7.1 Removing and installing connections for audio/video signal external source . . . . . . . . . . 54
8unless authorised
SmartGateby KODA system
AUTO A. S.. KODA
. . . . .AUTO
. . . A.. .S..does
. . .not. .guarantee
. . . . . or. .accept
. . . any
. . liability
........................... 56
8.1 General points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
8.2 SmartGate system - check the correct function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
8.3 Remove and install control unit for information electronics 2 J829 (SmartGate) . . . . . . . . 58
8.4 Set the parameters for the Wi-Fi connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
8.5 Update firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
92 - Windscreen wash/wipe system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

1 Windscreen and rear window wiper system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
1.1 Removing and installing the washer pump and washer fluid reservoir . . . . . . . . . . . . . . . . 62
1.2 Removing and installing the spray nozzles for windscreen washer system . . . . . . . . . . . . 63
1.3 Removing and installing the spray nozzle for rear window washer system . . . . . . . . . . . . 64
1.4 Repairing washer fluid level pipes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
2 Headlamp cleaning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
2.1 Removing and installing headlight cleaning system pump V11 . . . . . . . . . . . . . . . . . . . . 66
2.2 Removing and installing the lift cylinder for spray nozzles of headlight . . . . . . . . . . . . . . . . 66
2.3 Bleed the headlamp cleaning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
ii Contents
3 Windscreen wiper and washer system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

3.1 Fault recognition and fault display, coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
3.2 Removing and installing the wiper arms with wiper blades and setting their final setting . . 68
3.3 Removing and installing wiper motor with linkage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
3.4 Removing and installing Sensor for rain and light detection G397 . . . . . . . . . . . . . . . . . . 71
3.5 Repairing the rain and light detector sensor G397 , Valeo manufacturer . . . . . . . . . . . . . . 73
4 Rear window wiper system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
4.1 Removing and installing the wiper arm with wiper blade and setting its final setting . . . . . . 75
4.2 Removing and installing rear window wiper motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
94 - Lights, bulbs, switches - exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

1 Headlights halogen headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
1.1 Summary of components of headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
1.2 Removing and installing headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
1.3 Adjusting headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
1.4 Replacing light bulbs in headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
1.5 Replace headlight fixing brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
1.6 Change headlight for right-hand and/or left-hand traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
1.7 Removing and installing headlight range control motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
2 Headlights Bi-xenon headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
2.2 Assembly overview - Bi-xenon headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
2.3 Summary of components Bi-xenon headlights with LED module . . . . . . . . . . . . . . . . . . 90
2.4 Removing and installing headlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
2.5 Replacing light bulbs and gas discharge lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
2.6 Change headlight for right-hand / left-hand traffic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
2.8 Replace headlight fixing brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
2.9 Removing and installing control unit for gas discharge lamp J343 left or J344 right . . . . . . 94
2.10 Remove and install performance module for the headlight J667 left or J668 right . . . . . . 95
2.11 Removing and installing Control unit for daylight driving light and side light J860 (LED module)
left and J861 right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
2.12 Removing and installing the cornering light and headlight range control unit J745 . . . . . . 95
2.13 Vehicle level sensor G78 front left or G76 rear left . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
2.14 Removing and installing headlight range control motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
3 Lights in the exterior mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
3.1 Side turn signal lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
3.2 Door entry lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
4 Tail lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
4.1 Removing and installing tail light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
4.2 Replacing the light bulbs of the tail light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
5 Fog lights, fog lights with the Corner function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.1 General description, fault recognition and fault display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
5.2 Removing and installing fog light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
5.3 Adjusting fog lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
5.4 Replacing bulb for the fog light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
6 Additional brake light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
6.1 Removing and installing the high level brake light - Octavia . . . . . . . . . . . . . . . . . . . . . . . . 110
6.2 Removing and installing the high level brake light - Octavia Combi . . . . . . . . . . . . . . . . . . 111
6.3 Removing and installing the high level brake light - Octavia Combi GreenLine . . . . . . . . . . 112
7 Registration number lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
7.1 Removing and installing registration number lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
7.2 Replacing bulb for the number plate light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
8 Steering
unlesscolumn
authorised switch . . . .A..S.. KODA
. . . . .AUTO
. . . A.. .S.. does
. . .not
. .guarantee
. . . . . or. .accept
. . . any
. . .liability
by KODA AUTO ................. 117
Contents iii
8.1 Summary of components of steering column switch with mechanical ignition/starter switch
........................................................................ 117
8.2 Summary of components of steering column switch with control unit for electronic steering
column lock J764 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
8.3 Removing and installing switch unit on the steering column . . . . . . . . . . . . . . . . . . . . . . . . 119
8.4 Removing and installing steering column electronics control unit J527 . . . . . . . . . . . . . . 120
8.5 Setting the correct installation position of the restoring ring with coil spring . . . . . . . . . . . . 121
8.6 Contact assignment on the steering column electronics control unit J527 . . . . . . . . . . . . 122
8.7 Self-diagnosis and fault indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
9 Steering lock with ignition starter switch and lock cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . 123
9.1 Removing and installing lock cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
9.2 Removing and installing steering lock housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
9.3 Removing and installing the ELV J764 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
9.4 Removing and installing ignition/starter switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
9.5 Removing and installing ignition key anti-removal lock solenoid N376 . . . . . . . . . . . . . . . . 126
10 Keyless unlocking of the vehicle/the steering, keyless start/stop KESSY system . . . . . . 128
10.3 Overview of components of the KESSY system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
10.4 Access and start authorisation control unit J965 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
10.5 Aerials of the KESSY system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
10.6 Removing and installing start/stop button and immobiliser reader coil for emergency start
........................................................................ 132
10.7 Lock with control unit for ELV J764 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
11 Parking aid and park steering assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
11.1 Summary of components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
11.2 Remove and install parking aid control unit J446 or parking aid and park steering assistant
control unit J791 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 136
11.3 Remove and install the front parking aid warning buzzer H22 . . . . . . . . . . . . . . . . . . . . . . 136
11.4 Removing and installing the rear parking aid warning buzzer H15 . . . . . . . . . . . . . . . . . . 137
11.5 Removing and installing parking aid senders and park steering assistant . . . . . . . . . . . . . . 138
11.6 Parking aid sender holder making holes, assignment, fitting location, gluing procedure
........................................................................ 139
11.7 Self-diagnosis of the parking aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
12 Optical parking assistant (rear view camera) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
12.2 Summary of components: Rear view camera system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
12.3 Removing and installing rear view camera system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
96 - Lights, bulbs, switches - interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

1 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
1.1 Lights in the roof lining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
1.2 Removing and installing the rear interior light on the left and right, replace . . . . . . . . . . . . 147
1.3 Removing and installing glove box light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
1.4 Removing and installing glove compartment light in the front centre console . . . . . . . . . . 148
1.5 Removing and installing door warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
1.6 Remove and install the footwell lighting for the driver and front passenger . . . . . . . . . . . . 149
1.7 Removing and installing rear footwell lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
1.8 Removing and installing luggage compartment light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
2 Interior switches, in the dash panel, the centre console and the doors . . . . . . . . . . . . . . . . 152
2.1 Removing and installing light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
152
2.2 Removing
unless authorised by KODA andAUTOinstalling
A. S. KODA headlight range
AUTO A. S. does controlorregulator
not guarantee ........................
accept any liability 152
2.3 Removing and installing switches in centre console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
2.4 Removing and installing warning light switch and indicator light of the front passenger airbag
deactivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
2.5 Removing and installing the switch for the power window lifter . . . . . . . . . . . . . . . . . . . . . . 154
iv Contents
2.6 Removing and installing the passenger side glove box light switch . . . . . . . . . . . . . . . . . . 156
2.7 Removing and installing interior monitoring deactivation switch E 267 and deactivation button
for vehicle inclination sender E 360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
2.8 Removing and installing the rear seat heating switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
3 Components in the luggage compartment and tailgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
3.1 Removing and installing the switch for the luggage compartment lighting . . . . . . . . . . . . . . 158
3.2 Removing and installing the tailgate release switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
4 Front camera for diver assistance systems R242 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
4.1 Removing and installing front camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
4.2 Removing windscreen heating plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
5 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
5.1 Removing and installing horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
6 Anti-theft warning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
6.1 General points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
6.2 Removing and installing the horn H12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
6.3 Removing and installing interior monitoring sensor G273 and vehicle inclination sender G384
...................................................................... 163
6.4 Removing and installing interior monitoring deactivation switch E267 and deactivation button
for vehicle inclination sender E360 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
7 Sockets, cigarette lighter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
7.1 Removing and installing the 12 V power socket/cigarette lighter in the centre console . . . . 164
7.2 Removing and installing the luggage compartment 12 V power socket . . . . . . . . . . . . . . . . 164
7.3 Inverter with socket, 12 V / 230 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
8 Immobiliser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
8.1 Immobiliser control unit J362 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
8.2 Ignition key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
8.3 New identity when changing all the components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168
8.4 System test result (online connection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
97 - Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
1 Fuse holder and relay carrier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
1.1 Removing and installing relay
unless holder
authorised andAUTO
by KODA fuseA.holder
S. KODA behind
AUTO A. dash panel
S. does not . . or. accept
guarantee . . . . any
. . liability
..... 170
respect to the correctness of information in this document. Copyright by KODA AUTO A. S.
1.2 Removing and installingwith relays and fuse holder in the engine compartment and E-Box (relays
and fuse holder in the engine compartment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
2 Control units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
2.1 Vehicle voltage control unit J519 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
2.2 Data bus diagnostic interface Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
3 Vehicle diagnosis, measurement and information systems, diagnostic connection . . . . . . 181
4 Wiring loom and plug repair, contact surface cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
5 Vehicle diagnosis, testing and information systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
6 Wiring loom and plug repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
7 Use contact surface cleaning set VAS 6410 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Contents v
vi Contents
27 Starter, current supply, CCS

1 Contact corrosion
(SRL000764; Edition 12.2014)
The use of unsuitable connection elements (screws, nuts, wash
ers, ) causes contact corrosion.
This is why only connection elements with a special surface coat
ings are fitted.
Therefore, the rubber or plastic parts and the adhesives are made
from electrically non-conductive materials.
In case of doubt regarding the re-use of certain parts, the use of
new parts is recommended.
WARNING
It is recommended to use only original connection material

as well as spare parts which are tested and compatible
with aluminium, see Electronic Catalogue of Original
Parts .
It is recommended to use only koda accessories.
Any damage resulting from contact corrosion is not cov
ered by the terms of the warranty.
Note Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
It is possible to use the contact surface cleaning set -
VAS6410- for repair work on contact surfaces which show
traces of contact corrosion (oxidation).
Examples for application of the contact surface cleaning set -
VAS6410- can be found in the Workshop Manual Electrical
System General notes Electrical System General notes;
Rep. gr. 97 .
1. Contact corrosion 1
2 Battery
WARNING
When working on the battery, wear proper protection and ob

serve safety precautions (see Electrical System General
notes Electrical System General notes; Rep. gr. 27 ).
2.1 Basics, battery types, page 2

2.2 Warning instructions and safety precautions when working
on the battery, page 2
2.3 Work sequence when disconnecting and connecting the
battery, page 2
2.4 Checking battery, page 4
2.5 Charging battery, page 4
2.6 Removing and installing battery, page 5
2.7 Removing and installing battery tray, page 6
2.8 Battery parameterisation, page 7
2.1 Basics, battery types Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Batteries with a magic eye and plugs covered in adhesive tape of information in this document. Copyright by KODA AUTO A. S.
with respect to the correctness
are factory-installed in all vehicles (except vehicles with start-stop
system).
In vehicles with start/stop system, (depending on types of engines
see Electronic Catalogue of Original Parts ) a fleece battery
(AGM) or a battery with magic eye with EFB technology (En
hanced Flooded Battery) is mounted.
The AGM battery is also mounted in vehicles with auxiliary heat
ing and additional heating.
Description of the function, test and maintenance of the previous
batteries see Electrical System General notes Electrical
System General notes; Rep. gr. 27 .
2.2 Warning instructions and safety precau

tions when working on the battery
All the notes and comments to this chapter can be found in the
Workshop Manual Electrical System General notes Elec
trical System General notes; Rep. gr. 27 .
2.3 Work sequence when disconnecting

and connecting the battery
2.3.1 Disconnecting battery, page 2
2.3.2 Work sequence when connecting the battery,
page 3
2.3.1 Disconnecting battery

Switch off all electrical components and ignition, take out the
ignition key.
Open the cover of the heat protection sleeve.
2 Rep. gr.27 - Starter, current supply, CCS

Open cover -1-, loosen nut -3- and disconnect battery earth
strap -2- only.
Note
If both terminals are disconnected, only then disconnect pole ter

minal (-) from battery earth.
2.3.2 Work sequence when connecting the

battery
WARNING
Observe the following additional instructions after working on

the airbag system or on the electric belt tighteners or the safety
belts:
Switch on the ignition before connecting the battery.
Nobody should be in the vehicle when the battery is being
connected.
If the vehicle is equipped with the interface for entry and
start system (Kessy), the ignition should only be switched
on after connecting the battery using the Vehicle diag
nostic tester outside the vehicle cockpit (the valid ignition
key must be inside the vehicle) for safety reasons. This
procedure is part of the tests in the targeted fault finding.
Note
Neither grease nor oil the battery terminals.

The battery pole terminals must only be fitted by hand without
using any force in order to avoid damaging the battery hous
ing.
Install the battery pole terminals in such a way that the battery
poles are flush with the terminals or protrude.
If both terminals are disconnected, only then disconnect the
battery positive pole terminal (+).
The tightening torque is the same for all shapes of pole termi
nals (6 Nm).
After connecting the battery and switching on the ignition, the
warning light for the stability programme TCS/ESC and the
warning light for the power-assisted steering remain lit. The
warning lights go out automatically after driving a few metres
forward. Thereby the steering angle sender - G85- is activated
again.
Switch off all electrical components and take out the ignition
key.
2. Battery 3
Vehicles with battery monitoring control unit - J367- (with start/

stop system and auxiliary heating and additional heating)
Disconnect the plug -2- from the control unit -3- before con
necting to the battery.
Fit pole terminal (-) with control unit onto the - pole of the
battery, see fig., and tighten the fixing nut -1- (6 Nm).
Fit the plug -3- again onto the control unit.
Vehicles without battery monitoring control unit - J367-
Fit battery pole terminal of earth line -2- onto negative terminal
of battery and tighten the nut -3- arrow (6 Nm).
Continued for all vehicles:
When the battery is reconnected, perform the following opera
tions depending on the vehicle equipment:
Set clock.
Check the power windows Maintenance ; Booklet Octavia
III .
Connect the Vehicle diagnostic tester, interrogate the event
memory and delete any event entries.
2.4 Checking battery

All the notes and comments to the work sequence for checking
the battery can be found in the Workshop Manual Electrical Sys
tem General notes Electrical System General notes; Rep.
gr. 27 .
2.5 Charging battery

Open the cover -2- and connect the red charging terminal to
the battery plus (+) terminal. -1-.
On vehicles with a battery monitoring control unit - J367- ,
connect the black terminal of the charger to earthing point
-3-.
All other notes and comments to this chapter can be found in the
Workshop Manual Electrical system General notes Elec
trical system General notes; Rep. gr. 27.

2.6 Removing and installing battery
WARNING
Observe the battery handling instructions as well as the warn

ing instructions and safety precautions for lead acid batteries
2.2 Warning instructions and safety precautions when work
ing on the battery, page 2 .
Removing
Switch off all electrical components and ignition, take out the
ignition key.
Open cover -4-, loosen nut -6- and disconnect battery earth
strap -5-.
Open cover -3-, loosen nut -2- and connect positive cable to
the battery -1-.
Pull out heat protection sleeve -4-.

Unscrew the screw -2- (22 Nm) and remove securing bracket
for battery -1-.
Slide the battery out of the battery tray and remove it upwards.
Installing
Installation is carried out in the reverse order. When installing,
observe the following:
2. Battery 5
Insert battery into the battery tray -1- so that the battery base
is resting against the rear and the sides -arrows- up to the stop.
The nose -arrow- on the securing bracket -1- must enter the
recess in the battery base.
Tighten fixing screw -2- (15 Nm).
With the ignition and electrical components switched off, con
nect the positive terminal of the battery -3- and tighten the nut
-4- (6 Nm).
Note the work sequence when connecting the negative termi
nal and note the measures after reconnecting the battery
page 3 .
Caution
There are certain dangers if the battery is incorrectly mounted

or mounted loosely:
Shortened service life due to damage from vibration (dan
ger of explosion)
Damage of the grid plates of the battery.
Damage to battery housing by securing with
bracket
respect (possibil
ity of acid leaking, with high consequential costs)
Poor crash safety
2.7 Removing and installing battery tray

Removing
Remove air filter housing in front of the battery (does not apply
to 1.2 TSI; 1.4 TSI engine) Engine; Rep. gr. 23 diesel en
gines or Engine; Rep. gr. 24 petrol engines.
Remove the battery
2.6 Removing and installing battery, page 5 .
Screw out the screws -arrows- (9 Nm) and remove the battery
tray -1-.
Installing
Installation is carried out in the reverse sequence.

2.8 Battery parameterisation

This is performed only on vehicles with a battery monitoring con
trol unit - J367- when replacing the battery with a new one of
another type or with higher capacity.
After a new start battery is installed and the battery has been par
ameterised, the technical data of the new battery are sent to the
battery monitoring control unit - J367- .
Vehicle diagnostic tester connect and select the operating
mode Targeted fault-finding.
Select the Selected Functions/Components and subse
quently the following menu points using the button Skip:
Body
Electrical system
Diagnostic capable systems
Checking battery
Battery monitoring function
unless
Adaption
authorisedbattery
by KODAparameterisation
AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
2. Battery 7
3 Starter
3.1 Removing and installing starter, page 8
3.1 Removing and installing starter

Removing
Disconnect battery earth strap
2.3.1 Disconnecting battery, page 2 .
Remove air filter housing in front of the battery (does not apply
to 1.2 TSI; 1.4 TSI engine) Engine; Rep. gr. 23 diesel en
gines or Engine; Rep. gr. 24 petrol engines.
Move the protective cover -arrow-.
Unscrew nut -3- and disconnect positive cable.

Release and pull off connector -2-.
When earth strap is connected, unscrew nut -1- and loosen
earth strap.
Then screw out top fixing screw for starter -arrow-.

M12 80 Nm
M10 40 Nm
Vehicles fitted with a manual gearbox:
Remove the sound dampening system Body Protected
Work; by Rep.
copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
gr. 50 . unless authorised by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability

Unscrew nut -1- (23 Nm) and lay aside line holder -2- together
with line.
All vehicles:
Screw out bottom fixing screw -arrow- and remove the starter.
M12 80 Nm
M10 40 Nm
Installing
Caution
The line to terminal B+ must be laid and attached so that it does

not come into contact with rotating or moving parts of the as
sembly (e.g. with the shift mechanism, with rotating parts of the
assembly etc.)!
If the line is laid/attached incorrectly to terminal B+, there is a
risk of damage to the line and of a short circuit or fire.
Note
Use new self-locking nuts -1- and -3- for attaching the earth strap
and the positive cable, see Electronic Catalogue of Original
Parts .
Tightening torques for positive cable and earth strap:

Battery earth strap, Pos. -1- 20 Nm
Positive cable, Pos. -3-:
Starter with copper screw 16 Nm
Starter with steel screw 20 Nm
Pay attention to the work sequence when connecting the bat
tery
page 3 .
3. Starter 9
4 Generator
4.1 Checking generator, page 10
4.2 Removing and installing alternator, page 10
4.3 Fixing the B+ wire to the AC generator, page 12
4.4 Checking the carbon brushes of the AC generator,
page 13
4.5 Removing and installing the Bosch voltage regulator, page
13
4.6 Removing and installing the Valeo voltage regulator, page
14
4.7 Removing and installing the V-ribbed belt pulley on the AC
generator, page 14
4.8 Removing and installing the V-ribbed belt pulley with free
wheel, page 15
4.1 Checking generator

The AC generator can be inspected with the Vehicle diagnostic
tester in the function Targeted fault finding point body / elec
trical system / 27-starter, voltage supply / electrical components /
AC generator - C- .
4.2 Removing and installing alternator

Removing
Disconnect battery
Protected by copyright.earth
Copyingstrap
for private or commercial purposes, in part or in whole, is not permitted
2.3 Work
unless sequence
authorised by KODAwhenAUTO A. disconnecting
S. KODA AUTO A.and connecting
S. does not guarantee or accept any liability
the battery, page 2 .
Remove the V-ribbed belt engine; Rep. gr. 13 .

Vehicles with TDI engine
Remove the fuel filter Engine; Rep. gr. 20 and lay it to the
side (do not detach hoses).
Vehicles with TDI and 1.2/1.4/1.8 TSI engines:
Remove the sound dampening system Body Work; Rep.
gr. 50 .
Remove fan shroud with cooling fans Engine; Rep. gr. 19 .
Remove AC compressor (do not open the refrigerant circuit)
and secure to the side so that the intake hoses are not exces
sively strained Heating, Air Conditioning; Rep. gr. 87 .

1.8 TSI engine Loosen hose clamps -2-, unscrew screws

-arrows- and remove air flow hose.
Note
Close open lines with clean plug for example from the blanking
plug set -VAS 6122- .
For 1.2 TSI engine remove guide roller, and for 1.4 TSI remove
deflection roller Engine; Rep. gr. 13 .
All vehicles:
Remove the screen cap from the fixing nut of the B+ cable
-1- and unscrew the nut.
Unplug connector -2-.
Unscrew the securing nut (3.2 Nm) for line holder -3- or unclip
the line (engine-dependent), and lay the line to the side.
Vehicles with AC generator secured from the front side screw

out screws -arrows- (23 Nm).
If the AC generator is jammed in the holder, screw the screws
back in, then loosen them in two turns.
Tap the screw heads gently with the flat side of the hammer.
This will loosen the bushings that are used for securing the AC
generator.
4. Generator 11
Vehicles with AC generator secured from the side screw out

screws -arrows- (23 Nm).
Remove AC generator downwards.
Installing
Caution
Follow the mounting sequence for the V-ribbed belt Engine;

Rep. gr. 13
Fix the B+ wire correctly to the AC generator
4.3 Fixing the B+ wire to the AC generator, page 12 .
Vehicles with AC generator secured from the front side for

easier mounting move the threaded bushes -A- approx. 3 mm
-arrows-.
Observe the tightening torque for fastening the B+ wire see
4.3 Fixing the B+ wire to the AC generator, page 12 .
tery
2.3 Work sequence when disconnecting and connecting
After work has been carried out, always start the engine and
check that the belt is running correctly.
4.3 Fixing the B+ wire to the AC generator
Caution
The screw connection for the B+ cable at the generator is iden
tified with B1+!
If the B+ cable is not tightened to the specified tightening tor

que, this may result in the following risks:
The battery will not charge fully.
Complete failure of vehicle electronics
Spark formation may cause a fire
Damage resulting from overvoltage on electronic compo
nents and control units
The line to terminal B+ must be laid and attached so that it does
not come into contact with rotating or moving parts of the as
sembly (e.g. with the shift mechanism, with rotating parts of the
assembly etc.)!
If the line is laid/attached incorrectly to terminal B+, there is a
risk of damage to the line and of a short circuit or fire.

Note
Always use a new self-locking nut for attaching the B+ cable

-arrow-, see Electronic Catalogue of Original Parts .
The tightening torque for the self-locking nut of the B+ cable

-arrow- is 20 Nm.
4.4 Checking the carbon brushes of the AC

generator
Length of carbon brushes when new = 12 mm
Wear limit = 5 mm
Tolerance of carbon brushes to each other = +1 mm
4.5 Removing and installing the Bosch volt

age regulator
Careully prise off the protective cover -1- from the generator.
Screw out fixing screws -arrows- (2 Nm) of the voltage regu

lator and remove voltage regulator.
Installation is carried out in the reverse order.
4. Generator 13
4.6 Removing and installing the Valeo volt

age regulator
Press off screen cap on the rear side of the generator
-arrows-.
Unscrew screws -1- and nut -2-.

Remove voltage regulator.
4.7 Removing and installing the V-ribbed

belt pulley on the AC generator
Special tools and workshop equipment required
Socket - T30032-
Remove ribbed V-belt and/or generator
4.2 Removing and installing alternator, page 10 .
Remove the V-ribbed belt pulley using the socket insert -
T30032- .
Removal - turn the alternator shaft to the right.
Installation - turn the alternator shaft to the left.
Tightening torque: 65 Nm

4.8 Removing and installing the V-ribbed

belt pulley with free wheel
Polygon-head adapter - MP 1-309-
Remove ribbed V-belt and/or generator
4.2 Removing and installing alternator, page 10 .
Remove the V-ribbed belt pulley using the polygon-head
adapter - MP 1-309- .
Removal - turn the alternator shaft to the right.
Installation - turn the alternator shaft to the left.
Tightening torque: 80 Nm
Clip the protective cap onto the belt pulley with free wheel.
4. Generator 15
5 Start-stop system
5.1 Safety precautions for vehicles with start-stop system,
page 16
5.2 General description, page 16
5.3 Fault recognition and fault display, page 17
5.4 Battery recharging or starting by external source on vehi
cles with battery monitoring control unit J367 , page 17
5.5 Replacing the battery on vehicles with battery monitoring
control unit J367 , page 17
5.6 Battery monitoring control unit J367 , page 17
5.7 Button for start-stop system, page 18
5.1 Safety precautions for vehicles with

start-stop system
Caution
Risk of injury from automatic engine start.

On vehicles with activated start-stop system (recogniza
ble by a message in the dash panel insert) there is a risk
that the engine can start automatically.
It is therefore necessary to ensure that the start-stop sys
tem is deactivated when carrying out work on the vehicle
(switch ignition off, if required switch ignition on again).
5.2 General description

The start-stop system is designed to reduce fuel consumption and
thus contributes to the reduction of pollutant emissions.
For this purpose the engine automatically switches off during
standstill phases of the vehicle and restarts automatically or when
operating the clutch pedal.
The system is always automatically activated when the ignition is
switched on and can be deactivated with the start-stop button in
the centre console.
Detailed description of the function as well as conditions for the
operation of the start-stop system see:
Self-study programme No. 86 ; Start-stop system in koda
vehicles
Owner's manual Octavia III
Connection diagram of the start-stop system Current flow dia
grams, Electrical fault finding and Fitting locations.
Note
The components adapted for the start-stop system are not

specifically designated and differ only slightly from the usual
components (e.g. starter, generator).
When carryingProtected
out repairs, pay
by copyright. attention
Copying toorthe
for private correct
commercial desig
purposes, in part or in whole, is not permitted
nation of the spare parts see Electronic Catalogue of
Original Parts .

5.3 Fault recognition and fault display

For fault finding use the Vehicle diagnostic tester in the function
Targeted fault finding.
5.4 Battery recharging or starting by exter

nal source on vehicles with battery mon
itoring control unit - J367-
When recharging or starting by external source, pay attention to
the following points:
Do not disconnect the earth strap of the battery when recharging.
First of all connect to the positive terminals using the charge or
jump leads; then connect to the body mass (do not connect to the
negative terminal of the battery).
Note
The direct charging (starting aid) of the battery at the negative

terminal results in the bypass of the battery monitoring control
unit - J367- (then the current flow isbynot monitored by thisAUTO con
unless authorised KODA AUTO A. S. KODA A. S. does not guarantee or accept any liability
trol unit). with respect to the correctness of information in this document. Copyright by KODA AUTO A. S.
The values regarding the battery state, which are stored in the
data bus diagnostic interface - J 533- (Gateway), would then
no longer correspond to the values of the charged battery.
This can lead to the failure of the start-stop system or the aux
iliary heating and additional heating.
Testing and charging the battery Electrical System General
notes Electrical System General notes; Rep. gr. 27 .
5.5 Replacing the battery on vehicles with

battery monitoring control unit - J367-
Owing to their greater cycle stability during cold starting, a fleece
battery (AGM) or a battery with magic eyes with EFB technology
(Enhanced Flooded Battery) is used as a start battery in place of
the usual lead-acid batteries.
Description see Electrical System General notes Electrical
System General notes; Rep. gr. 27 .
Note
When replacing the battery, only install a fleece battery (AGM)

again or a battery with EFB technology with the same capacity.
5.6 Battery monitoring control unit - J367-

The control unit is located directly at the negative connection ter
minal of the battery earth strap.
It transmits information on whether the battery has enough elec
tric power for the operation of the start-stop system or auxiliary/
additional heating.
It is connected to the data bus diagnostic interface - J533- (Gate
way) via the LIN data bus.
In the event of a failure, an entry is made in the event memory.
The start/stop system/auxiliary heating and additional heating is
switched off.
5. Start-stop system 17
Note
After replacing, adapt (code) the new battery monitoring control

unit - J367- with Vehicle diagnostic tester.
5.7 Button for start-stop system

Removing and installing the button for the start-stop system
2.3 Removing and installing switches in centre console, page
153 .

6 Cruise control system (CCS)

The engine control unit controls the function of the CC on vehicles
which have a cruise control.
Fault recognition and fault display
Faults of the CC are transmitted via the engine control unit.
Detailed description of the function Owner's manual Octavia
III .
For fault finding use:
Vehicle diagnostic tester in the function Targeted fault find
ing.
Current flow diagrams, Electrical fault finding and Fitting lo
cations.
6. Cruise control system (CCS) 19

7 Automatic distance control (adapted

CC) and Front Assist
7.2 Overview of the fitting positions: Automatic distance con
trol, Front Assist, page 20
7.3 Removing and installing the clearance control control unit
J428 , page 22
7.4 Removing and installing retaining plate for clearance con
trol control unit J428 , page 22
7.5 Calibrate automatic distance control, page 23

Adaptive CC (ACC) regulates the distance from the vehicle in
front based on the pre-set speed and distance.
Front Assist identifies the critical situations in the distance to
the obstacle and helps lower the braking distance (also avail
able as a stand-alone device without ACC)
Front Assist works independently, even ACC is switched off.
Detailed description of the function of Automatic distance control
and Front Assist Owner's manual Octavia III .
7.2 Overview of the fitting positions: Automatic distance control, Front Assist

1 - Dash panel insert

with control unit in dash
panel insert - J285-
2 - Switch unit on the steering
column
Equipment variant with
adaptive CCS
Removing and installing
8.3 Removing and in
stalling switch unit on
the steering column,
page 119
3 - Adaptive CCS switch - E45-
only for vehicles with
adaptive CCS
Component part of the
switch unit on the steer
ing column
8.3 Removing and in
stalling switch unit on
the steering column,
page 119
4 - Cover
5 - Connector
6 - Clearance control control
unit - J428-
7.3 Removing and in
stalling the clearance
control control unit J428
, page 22
Calibration
7.5 Calibrate auto
matic distance control,
page 23
7 - Holder for clearance control control unit - J428-
On the new part, the pin bolts -Pos. 8- are pre-configured in the base position
8 - Pin bolt
Adjustment bolts for clearance control control unit - J428-
2 pieces
9 - Retaining plate
Removing and installing Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
7.4 Removing and installing
unlessretaining
authorised byplate
KODAfor clearance
AUTO A. S. KODAcontrol
AUTO A. S.control
does not unit J428
guarantee , page
or accept 22
any liability
10 - Quick-release fitting
3 pieces
Replace after disassembly
11 - Screw
2 pieces
8 Nm
7. Automatic distance control (adapted CC) and Front Assist 21

7.3 Removing and installing the clearance

control control unit - J428-
Note
When replacing the Clearance control control unit - J428- , con

nect Vehicle diagnostic tester and, in the operating mode
Targeted fault finding or Targeted functions ,select the function
Replace relevant control unit.
Removing
Switch off the ignition and all electrical components.
Remove front bumper Body Work; Rep. gr. 63 .
Unscrew screws -3- (8 Nm) and remove control unit -1- with
retaining plate.
Where necessary, remove locking lugs -arrows A-, tilt out con
trol unit -1- -arrow B- and push out from the holder -3-.
Separate plug connection -2-.
Install
Installation is performed in the reverse order, pay attention to the
following points:
Calibrate automatic distance control
7.5 Calibrate automatic distance control, page 23 .
7.4 Removing and installing retaining plate

for clearance control control unit - J428-
Removing
Removing steering column electronics control unit - J428-
7.3 Removing and installing the clearance control control
unit J428 , page 22 .

Unlock quick-release fittings -2- by rotating it -arrow-.

Remove quick-release fittings -2- from the pin bolts -1-.
Remove retaining plate -3- from the control unit -4-.
Install
following points:
Replace quick-release fittings -2-.
Press pin bolts -1- until they lock into the quick-release fittings.
Calibrate automatic distance control
7.5 Calibrate automatic distance control, page 23 .
7.5 Calibrate automatic distance control

Work procedure to calibrate automatic distance control Chas
sis; Rep. gr. 44 .
7. Automatic distance control (adapted CC) and Front Assist 23

90 Gauges, instruments
1 Dash panel insert
1.2 Adjust/replace dash panel insert, page 24
1.3 Removing and installing dash panel insert, page 24
1.4 Warning lights in the dash panel insert, page 26
1.5 The self-diagnostic function of the dash panel insert, page
27

Technology of the dash panel insert
The dash panel insert is supplied in three versions.
1 - Basic version with segment display Basic
Without multi-function display
With multi-function display
2 - Dash panel insert with information display (TFT) Medium
3 - Dash panel insert with colour information display (TFT) Col
our
All panel operations are visually identical.
Description of the function and control:
Self-study programme No. 97 ; koda Octavia III Vehicle
presentation
Contact assignment of plug connection on the dash panel insert
Current flow diagrams, Electrical fault finding and Fitting loca
tions.
1.2 Adjust/replace dash panel insert

Vehicle diagnostic tester connect online.
If the dash panel insert is replaced, the Vehicle diagnostic tester
must be connected before the removal of the original dash panel
insert and must be confirmed in the replace control unit Guided
Functions. Thereby, the required values are read into the diag
nostic unit from the original dash panel insert. If the original dash
panel insert is not available or does notwithcommunicate with the
diagnostic unit, then proceed according to the information in the
Vehicle diagnostic tester
After fitting the new dash panel insert, adapt all ignition keys.
1.3 Removing and installing dash panel in

sert
Note
After reading in the information stored in the control unit, the work
sequence adjust/replace dash panel insert must be carried out
before replacing the dash panel insert
1.2 Adjust/replace dash panel insert, page 24 .
24 Rep. gr.90 - Gauges, instruments

Removing
Pull steering wheel out fully and lock it in its lowest position.
Take hold of the bottom cover of the control panel -1- and un
clip it from the catches.
Unscrew screws -2- and push out the dash panel insert -1-
-arrow-.
Press the catch -1- and disconnect the plug connection by tilt
ing out the clamp -arrow-.
Installing
Attach the plug connection and insert the dash panel insert
until it locks into the assembly opening -Detail-.
Screw in screws -2- (1.5 Nm) and install the lower cover.
Note
For fault finding perform self-diagnosis

1.5 The self-diagnostic function of the dash panel insert,
page 27 .
Contact assignment of plug connection Current flow dia
1. Dash panel insert 25

1.4 Warning lights in the dash panel insert
Note
Detailed description of the function of warning lights Owner's manual Octavia III .
The arrangement and number of warning lights depends on the equipment level and type of dash panel
insert.
1 - Attach the front seatbelt

2 - Tyre pressure
3 - Power-assisted steering
4 - Microelectronics check
(petrol engine)
Diesel engines - glow
period
26 Rep. gr.90 - Gauges, instruments

5 - Exhaust gas control system

6 - Trailer indicator light
7 - Warning light for stability
(ESC)
8 - Antilock braking system
(ABS)
9 - Main beam assist
10 - Warning signal black ice
11 - Start/stop system
12 - Attach the rear seatbelt
13 - Washer fluid level
14 - Engine oil
15 - Generator
16 - Fog lights
17 - Rear fog light
18 - Selector lever lock
19 - Pad thickness
20 - Fuel reserve
21 - not activated
22 - Follow Lane Assist
23 - Coolant temperature, coolant amount
24 - Cruise control system
25 - Warning/hazard (orange/red)
26 - Light failure
27 - Handbrake
28 - not activated
29 - Diesel particle filter (diesel engine)
30 - Brake system
31 - Main beam
32 - Switch off control for traction
33 - Safety system
1.5 The self-diagnostic function of the dash

panel insert
Initiating self-diagnosis of the dash panel insert
The dash panel insert is controlled by a microprocessor
unless authorised byand
KODAfeaAUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
tures a comprehensive self-diagnosis. If faults occur in the system
components, fault codes are stored in the event memory of the
dash panel insert.
Perform self diagnosis with the vehicle diagnosis, measurement
and information system - VAS 5051- in the fault finding function.
1. Dash panel insert 27

91 Communication
1 Multimedia information system In
fotainment
1.1 General points, page 28
1.2 Installation Infotainment system, page 29
1.3 Infotainment summary of components with radio,
page 31
1.4 Infotainment summary of components with navigation,
page 32
1.5 Electronic anti-theft coding, page 33
1.6 Removing and installing the Infotainment display/control
unit, page 33
1.7 Infotainment self-diagnosis, page 36
1.1 General points

Infotainment system = Multimedia information system (MIB
modular infotainment kit).
It enables the driver to access the vehicle setting, assistance
systems and comfort functions via a single system.
Even the basic version can fully cover the entertainment, com
munication and vehicle interaction needs of the vehicle occu
pants.
Further information and description of function:
Self-study programme No. 97 ; koda Octavia III Vehicle pre
sentation
tions
28 Rep. gr.91 - Communication

1.2 Installation Infotainment system

1.2.1 Basic Infotainment features (entry), page 29
1.2.2 Medium Infotainment features (standard), page 30
1.2.3 High Infotainment features (high), page 30
1.2.1 Basic Infotainment features (entry)

Construction Blues, Swing
Blues
Monochrome display
Media inputs AUX-IN points; USB/MEDIA IN (Mitsumi)
AM/FM radio
Vehicle comfort functions displays and settings
Optional expansions for:
4x speakers rear
Swing
Function such as Blues, in addition:
CD drive
SD card slot
Bluetooth
Phonebox
1. Multimedia information system Infotainment 29

1.2.2 Medium Infotainment features (stand

ard)
Bolero, Amundsen installation
1- Display unit
2- Control unit
Bolero
Capacitive colour touch display
CD drive; SD card slot
AM/FM radio
DAB (digital receiver)
CANTON sound system
Voice control
Apple connectivity
Bluetooth
Phonebox
Amundsen
Functions such as Bolero, plus:
2 x SD card slot
Navigation with 2D and 2.5D display (bird's eye view)
Bluetooth in basic configuration
1.2.3 High Infotainment features (high)
Columbus
1- Display unit
2- Control unit
Capacitive colour touch display
DVD drive; 2 x SD card slot
AM/FM radio
Navigation with 2D, 2.5D display (bird's eye view); 3D
Bluetooth
Dual DAB tuner (digital receiver)
CANTON sound system
Phonebox
Traffic sign recognition

1.3 Infotainment summary of components with radio

The number and the design of the components depend on the
vehicle equipment.
1 - Front treble speaker

6.2 Removing and in
stalling front treble loud
speakers, page 52
2 - Multi-functional steering
wheel
Description and body
work
4 Multi-functional
steering wheel,
page 47
3 - Rear treble speaker
6.3 Removing and in
stalling the rear treble
speaker, page 52
4 - Infotainment display unit
(Bolero)/display and control
unit (Blues, Swing)
1.6 Removing and in
stalling the Infotainment
display/control unit,
page 33
5 - Infotainment control unit
(Bolero)
1.6.3 Infotainment
control unit Bolero,
Amundsen and Colum
bus , page 35
6 - Rear window aerial
Combi type - aerials fit
ted into the rear side
window
Additional information and aerial overview 2 Aerial systems, page 37
7 - Connections for external audio/video sources
7 Connections for audio/video signal MEDIA IN (multimedia socket) external source, page 54
8 - Mid-bass speaker rear
6.1 Removing and installing the front and rear mid-bass speaker, page 52
9 - Mid-bass speaker front
31
1. Multimedia information system Infotainment
1.4 Infotainment summary of components with navigation

The number and the design of the components depend on the
vehicle equipment.

6.2 Removing and in
speakers, page 52
2 - Multi-functional steering
wheel
Description and body
work
4 Multi-functional
steering wheel,
page 47
6.3 Removing and in
stalling the rear treble
speaker, page 52
1.6 Removing and in
page 33
1.6.3 Infotainment
Amundsen and Colum
bus , page 35
6 - Roof aerial
for GPS signal receipt
Additional information,
removing and installing
2 Aerial systems,
page 37
7 - Rear window aerial
Combi type - aerials fitted into the rear side window
Additional information and aerial overview 2 Aerial systems, page 37
8 - Connections for external audio/video sources
7 Connections for audio/video signal MEDIA IN (multimedia socket) external source, page 54

1.5 Electronic anti-theft coding

The Infotainment display/control unit is equipped with an elec
tronic comfort anti-theft coding, which operates in combination
with the dash panel insert.
The Infotainment display/control unit must be paired with an ap
propriate vehicle using the Vehicle diagnostic tester. The se
curity code is no longer entered.
The Infotainment display/control unit, which is assembled at the
factory, is paired only when it is used for the first time with the
corresponding vehicle. If the battery is disconnected and then re
connected or if the Infotainment display/control unit is removed
from a vehicle and then re-installed in the same vehicle, pairing
with the corresponding vehicle is no longer valid.
If the dash panel insert is replaced, the Infotainment display/con
trol unit must be paired with the relevant vehicle once again.
The user must have a valid authorisation to use a programme for
pairing the Infotainment display/control unit.
Additional information Infotainment operating manual .
1.6 Removing and installing the Infotain

ment display/control unit
1.6.1 Infotainment display/control unit Blues and Swing , page
33
1.6.2 Infotainment display unit Bolero, Amundsen and Colum
bus , page 34
1.6.3 Infotainment control unit Bolero, Amundsen and Colum
bus , page 35
1.6.1 Infotainment display/control unit Blues

and Swing
Release tool - T10057-
The Infotainment display and control forms a single unit.
Removing
Remove the data storage device that is still in the unit.
Insert unlocking tools into the openings in the display unit
-see fig.- until there is an audible click.
Remove the display/control unit by pulling on the unlocking
tools -arrows-.

Compress plug catch -arrows-.
Open catch clamp -arrow- and disconnect plug.

Release and pull off other plug connections.
Press back catches from the side and remove the unlocking
tools.
Installing
Note
When inserting the display and control unit, on no account press

on the display or on the operating buttons, otherwise they will be
damaged.
When replacing the pairing andunless

the authorised
coding by ofKODA
the Infotainment
AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
display and control unit, see with respect to the correctness of information in this document. Copyright by KODA AUTO A. S.
1.5 Electronic anti-theft coding, page 33 .
1.6.2 Infotainment display unit Bolero,

Amundsen and Columbus
Release tool - T10057-
Removing
Insert unlocking tools into the openings in the display unit

Remove the display unit by pulling on the unlocking tools

-arrows-.
Release and disconnect the plug connections.
Press back catches from the side and remove the unlocking
tools.
Installing
Note
When inserting the display unit ,on no account press on the dis
play or on the operating buttons, otherwise they will be damaged.
When replacing the Infotainment display unit pairing see

1.5 Electronic anti-theft coding, page 33 .
1.6.3 Infotainment control unit Bolero,

Amundsen and Columbus
Removing
RemoveProtected
the data storage
by copyright. device
Copying thatoriscommercial
for private still in the Infotainment
control unless
unit Infotainment operating manual .
authorised by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability

Vehicles manufactured up to CW 13/2013:
Remove the glove compartment Body Work; Rep. gr. 70 .
Put your hand behind the control unit and loosen the cable ties
from the fin on the heating and air conditioning unit.
All vehicles:
Insert unlocking tools into the openings in the control unit
Note
Mask the lower edge of the assembly opening with commercially

available tape that will not scratch the lining when the connectors
are removed.
Remove the display unit by pulling on the unlocking tools

-arrows-.

Compress plug catch -arrows-.
Open catch clamp -arrow- and disconnect plug.

Release and pull off other plug connections.
Installing
Vehicles manufactured up to CW 13/2013:
Caution
After inserting the unit into the assembly opening it is essential

to once again secure the wiring loom to the fin on the heating
and air conditioning unit.
If the wiring loom is installed incorrectly, there is a risk that the
wiring loom will collide with the recirculating air flap for the
heating and air conditioning unit.
Following installation, perform a visual inspection of recircu

lating air flap operation.
All vehicles:
When replacing the pairing and the coding of the Infotainment
control unit, see 1.5 Electronic anti-theft coding, page 33 .
1.7 Infotainment self-diagnosis

Carry out self-diagnosis with the Vehicle diagnostic tester in
the function Targeted fault finding.

2 Aerial systems
2.1 Overview of the aerial systems, page 37
2.2 Removing and installing the roof aerial, page 39
2.3 Removing and installing frequency filters for frequency
modulation (FM) in the positive cable R179 , page 40
2.4 Removing and installing frequency filters for frequency
modulation (FM) in the positive cable R178 , page 40
2.5 Removing and installing AM/FM, FM2/DAB aerial module
(amplifier), page 41
2.6 Replacing aerial cables, page 42
2.1 Overview of the aerial systems
Note
The number of components of the aerial system depends on

the vehicle equipment.
When equipped with Infotainment Blues and Swing, the
display unit -Pos. 3- and the control unit -Pos. 4- form a single
unit.
Further information and description of functions Self-study
programme No. 97 ; koda Octavia III Vehicle presentation .
2.1.1 Octavia, page 37

2.1.2 Octavia Combi, page 39
2.1.1 Octavia
2. Aerial systems 37
1 - Induction plate
Forms the GSM signal
induction field
3.4 Removing and in
stalling induction plate,
page 45
2 - Signal amplifier for mobile
phones
3.3 Removing and in
stalling the aerial signal
reception amplifier
(compensor),
page 44
5 - Frequency filter for the fre
quency modulation (FM) in the
negative cable - R178-
Prevents the aerial sig
nals from being short-
circuited to earth
2.3 Removing and
installing frequency fil
ters for frequency mod
ulation (FM) in the posi
tive cable R179 ,
page 40
6 - Aerial module (amplifier)
AM/FM reception
2.5 Removing and in
stalling AM/FM, FM2/
DAB aerial module (amplifier), page 41
7 - Rear window aerial -R130-
FM2/DAB reception
2.5 Removing and installing AM/FM, FM2/DAB aerial module (amplifier), page 41
9 - Frequency filter for the frequency modulation (FM) in the positive cable - R179-
Prevents the aerial signals from being short-circuited to earth
2.3 Removing and installing frequency filters for frequency modulation (FM) in the positive cable R179
, page 40
10 - Roof aerial
Removing and installing 2.2 Removing and installing the roof aerial, page 39
11 - Auxiliary heating radio controlled receiver - R64-
removing and installing Heating, Air Conditioning; Rep. gr. 82

2.1.2 Octavia Combi
1 - Induction plate
induction field
3.4 Removing and in
page 45
2 - Signal amplifier for mobile
phones
3.3 Removing and in
stalling the aerial signal
reception amplifier
(compensor),
page 44
5 - Rear right side window aer
ial
Body Work; Rep. gr.
64
AM/FM reception
2.5 Removing and in
DAB aerial module (am
plifier), page 41
FM2/DAB reception
2.5 Removing and in
DAB aerial module (amplifier), page 41
8 - Rear left side window aerial
Removing and installing Body Work; Rep.by gr.
Protected 64 Copying for private or commercial purposes, in part or in whole, is not permitted
copyright.
9 - Auxiliary heating radio controlled receiver with
- R64-
removing and installing Heating, Air Conditioning; Rep. gr. 82

10 - Roof aerial
Removing and installing 2.2 Removing and installing the roof aerial, page 39
2.2 Removing and installing the roof aerial

Removing
For vehicles without panoramic roof:
Undo the top B pillar trim and top C and D pillar trim (combi)
Body Work; Rep. gr. 70 .
Loosen headlining Body Work; Rep. gr. 70 and carefully
hang the rear part downward.
For vehicles with panoramic roof:

Unhook headlining Body Work ; Rep. gr. 70 .
Continued for all vehicles:
Release and disconnect plug connections -1- to the aerial ca
bles.
Unscrew screw -3-.
Open holding clamp -2- and remove the aerial.
Installing
Put aerial in position and press down the holding clamp -2-
until it clicks into place.
Tighten the fixing screw (6 Nm).
Further installation occurs in reverse order.
2.3 Removing and installing frequency fil

ters for frequency modulation (FM) in
the positive cable - R179-
Remove tailgate inner lining Body Work; Rep. gr. 70 .
Disconnect plug -1- and aerial cable -3-.
Unscrew screw -arrow A-, move filter -2- -arrow B- and take
out.
2.4 Removing and installing frequency fil

ters for frequency modulation (FM) in AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
unless authorised by KODA
the positive cable - R178-
Disconnect plug -1- and aerial cable -3-.
Use a screwdriver to disconnect filter -2- from the catch and
remove.

2.5 Removing and installing AM/FM, FM2/

DAB aerial module (amplifier)
Note
The work sequence for removing and installing is similar for

the two amplifiers.
Arrangement of the amplifier
2.1 Overview of the aerial systems, page 37 .
Removing
Octavia:
Octavia Combi:
Remove top C pillar trim on the side where the aerial module
is removed Body Work; Rep. gr. 70
All vehicles:
Unplug -arrows- connector.
Unscrew -arrow- screw (2 Nm).

Move aerial module -arrow- and unhook from the bracket.

Installing
2.6 Replacing aerial cables
Note
Aerial cables must not be repaired, but replaced with a new

original part see Electronic Catalogue of Original Parts ;
Accessories; Part group 35.
Do not crimp aerial cable or bend excessively! The minimum
bending radius must not be less than 50 mm.
Cut off aerial connection from the defective cable.

The remainder of the defective cable remains in the vehicle.
Lay new aerial cable close to the original cable and attach.
Perform a functional test.

3 Telephone system
3.1 General Instructions, page 43
3.2 Summary of components telephone system, page 43
3.3 Removing and installing the aerial signal reception ampli
fier (compensor), page 44
3.4 Removing and installing induction plate, page 45
3.5 Check induction plate, page 45
3.6 Removing and installing the microphone for the telephone
R38 , page 46
3.1 General Instructions

Vehicles with a mobile phone pre-installation have an integrated
Bluetooth unit in their Infotainment control unit which meets the
functions of a mobile phone pre-installation.
The mobile phone is connected via Bluetooth.
Infotainment operating manual
presentation
3.2 Summary of components telephone system
Note
The number of components for the telephone system depends on the vehicle equipment.
3. Telephone system 43
1 - Telephone microphone -
R38-
in the front interior light
3.6 Removing and in
stalling the microphone
for the telephone R38 ,
page 46
With integrated Blue
tooth module
1.6.3 Infotainment
Amundsen and Colum
bus , page 35
4 - Induction plate
induction field
3.4 Removing and in
page 45
check
3.5 Check induction
plate, page 45
5 - Roof aerial
2.2 Removing and in
stalling the roof aerial,
page 39
6 - Aerial signal reception am
plifier (compensor)
3.3 Removing and installing the aerial signal reception amplifier (compensor), page 44
3.3 Removing and installing the aerial signal

reception amplifier (compensor)
The compensor is located under the luggage compartment trim,
right side.
Remove right luggage compartment trim panel Body Work;
Rep. gr. 70 .
Release screws -arrows- (5 Nm).

Octavia
Octavia Combi
Disconnect plug and remove amplifier -1-.
3.4 Removing and installing induction plate

Remove storage compartment in the front centre console
Loosen induction plate -1- from the catches -arrows- and re
move it from the storage compartment -2-.
3.5 Check induction plate

Open the storage compartment in the central console and re
move the rubber layer onto which the mobile phone is fitted.
Switch on ignition.
3. Telephone system 45
Measure the resistance between the contacts -arrows- under

neath the washer with multimeter.
Measured values:
10 k - induction plate OK.
20 k - short circuit in the aerial
30 k - wire break
40 k - compensor fault
50 k - terminal 30, 15 on the compensor missing
3.6 Removing and installing the microphone

for the telephone - R38-
Removing
Remove front interior light
1.1.1 Removing and installing the front interior light, page
144 .
Loosen the microphone out of the retaining lugs -arrows- and
remove.
Disconnect plug.
Installing

4 Multi-functional steering wheel

4.2 Removing and installing the Infotainment switch units,
page 47
4.3 Removing and installing switch units for gearbox operation
in Tiptronic mode (gearbox 02E, 0AM DSG), page 48
4.4 Self-diagnosis of the multi-functional steering wheel, page
49

The multi-functional steering wheel contains (depending upon
equipment) the following components:
Multifunction buttons in the steering wheel on the left - E440-
and right -E441- for the operation of the Infotainment
Tiptronic switch in the steering wheel up - E438- and down -
E439- for the operation of the double clutch gearbox in Tip
tronic mode
Multifunctional steering wheel control unit - J453- , integrated
in the left front switch unit.
Note
When handling a fault, it is unless

absolutely essential
Protected by copyright. Copyingtoforknow the
private or func purposes, in part or in whole, is not permitted
commercial
tion and operation of the multi-functional steering wheel. Addi
tional information and description of function Owner's manual
Octavia III .
4.2 Removing and installing the Infotain

ment switch units
The assembly work is identical for both switch units.
Removing
Remove the airbag unit in the steering wheel Body Work;
Rep. gr. 69 .
Prise out the plate with switch units -2- evenly and carefully
out of the steering wheel -1- using the disassembly wedge
-arrows-.
Disconnect plug.
4. Multi-functional steering wheel 47

Remove bolts -3- (0.4 Nm).

When removing modules -1- and -2-, carefully loosen the con
nection cable from the bracket -arrows-.
Vehicles with automatic transmission with column gear shift
separate plug connections from switch units.
Installing
Note
Install connection cable for modules correctly in the line in the

plate -arrows-.
Before the airbag is installed, it must be checked if all the wiring
is properly pressed back into the guiding grooves in the steer
ing wheel foam. Wiring which protrudes can be damaged by
the backside parts of the airbag.
tery
Perform coding with Vehicle diagnostic tester when replac

ing the switch units.
4.3 Removing and installingProtected

switch unitsCopying
by copyright. for for private or commercial purposes, in part or in whole, is not permitted
gearbox operation in Tiptronic mode
(gearbox 02E, 0AM DSG)
The mounting sequence is identical for both switch units.
Removing
Remove the airbag unit in the steering wheel Body Work;
Rep. gr. 69 .
Prise out the plate with switch units -2- evenly and carefully
out of the steering wheel -1- using the disassembly wedge
-arrows-.
Disconnect plug.

Unscrew screw -arrow A- (1.7 Nm), swivel out switch unit for
gearbox operation -1- -arrow B- and remove.
Installing
Note
Before the airbag is installed, it must be checked if all the wiring

is properly pressed back into the guiding grooves in the steer
ing wheel foam. Wiring which protrudes can be damaged by
the backside parts of the airbag.
When tightening the screw -A- keep the button -1- in the right
position (edge of the button -1- on a line with the edge of the
steering wheel).
tery
4.4 Self-diagnosis of the multi-functional

steering wheel
The multi-functional steering wheel is capable of conducting a
self-diagnosis. Carry out self-diagnosis with the Vehicle diag
nostic tester in the function Targeted fault finding.
4. Multi-functional steering wheel 49

5 Canton sound system

5.1 Fitting position overview sound system components,
page 50
5.2 Removing and installing the sound system control unit,
page 51
5.3 Self-diagnosis of the equipment Sound system,
page 51
Further information and description of functions Self-study pro
gramme No. 97 ; koda Octavia III Vehicle presentation .
5.1 Fitting position overview sound system components

6.2 Removing and in
speakers, page 52
2 - Central speaker
In the dash panel, cen
tre
6.4 Removing and in
stalling the central
speaker, page 52
unless
6.3authorised
Removing andAUTO
in A. S. KODA AUTO A. S. does not guarantee or accept any liability
by KODA
stalling the torear
with respect treble of information in this document. Copyright by KODA AUTO A. S.
the correctness
speaker, page 52
4 - Subwoofer
6.5 Removing and in
stalling subwoofer,
page 53
6.1 Removing and in
stalling the front and
rear mid-bass speaker,
page 52
6 - Sound system control unit
5.2 Removing and in
stalling the sound sys
tem control unit,
page 51

5.2 Removing and installing the sound sys

tem control unit
Removing
key.
Push the left front seat completely towards the rear and the
highest point.
Remove expanding rivets -2- and remove cover -1- towards
the front.
Unscrew screws -4- (1.5 Nm).

Gently swivel out the control unit -1- and pull it out of the hold
er.
Loosen by tilting out the clamp and separate the plug connec
tion -3-.
Disconnect "MOST bus" data bus -2-.
Protect socket for MOST-Bus Databus -2- with cover -1-. You
can also use another suitable way (e.g. wrap around a clean
film and tape up).
Installing
When replacing, code the new control unit with the Vehicle
diagnostic tester.
If the MOST-Bus data bus is damaged, replace databus with
end pieces.
5.3 Self-diagnosis of the equipment Sound

system
Carry out self-diagnosis with the Vehicle diagnostic tester in
the function Targeted fault finding.
5. Canton sound system 51

6 Removing and installing loudspeak

ers
6.1 Removing and installing the front and rear mid-bass speak
er, page 52
6.2 Removing and installing front treble loudspeakers,
page 52
6.3 Removing and installing the rear treble speaker,
page 52
6.4 Removing and installing the central speaker, page 52
6.5 Removing and installing subwoofer, page 53
Loudspeaker types to be installed Self-study programme No.
97 ; koda Octavia III vehicle positioning .
6.1 Removing and installing the front and

rear mid-bass speaker
Removing
Remove the door trim panel from which the loudspeaker is
removed Body Work; Rep. gr. 70 .
Disconnect socket connector at the loudspeaker.
Disconnect expanding rivets -arrows- and remove loudspeak
er.
Installing
6.2 Removing and installing front treble

loudspeakers
The loudspeakers are built into the inside of the exterior mirror
cover.
In the case of a fault, replace the mirror cover with loudspeaker.
6.3 Removing and installing the rear treble

speaker
The treble speakers are firmly connected with the rear inner door
trim panel.
In the case of a fault, replace the rear inner door trim panel
6.4 Removing and installing the central

speaker
Only on vehicles with the equipment Soundsystem
Removing the dash panel Body Work; Rep. gr. 70 .

Screw out the screw -arrows- (0.3 Nm) and remove the loud
speaker.
6.5 Removing and installing subwoofer

Remove right side trim panel in luggage compartment Body
Work; Rep. gr. 70 .
Screw out fixing screws -see fig.- (3 Nm) and remove sub
woofer.
Disconnect plug.
6. Removing and installing loudspeakers 53

7 Connections for audio/video signal

MEDIA IN (multimedia socket) exter
nal source
7.1 Removing and installing connections for audio/video signal
external source, page 54
7.1 Removing and installing connections for

audio/video signal external source
Connections for the audio/video signal external source are loca
ted below the heating/air conditioning control.
Infotainment operating manual
presentation
Removing
Remove the Infotainment display unit
1.6 Removing and installing the Infotainment display/con
trol unit, page 33 .
Remove heating/air conditioning system heating, air con
ditioning system; Rep. gr. 87 .
Press out retaining clips -arrows A- one after each other, fold
out the bracket -1- -arrow B- and push out the connected cable
lengths to each other.
Connection MEDIA IN (Mitsumi):
Engage a small screwdriver into the middle of the plug at an

angle from below, unlock by pressing together, and remove
the plugs -3- one after the other.
Completely release sensors -2- from the catches -arrows- and
take out.
USB and AUX connections: Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted

Unlock the plugs from the USB connection -3- from the top and
remove.
Insert a small screwdriver into the middle of the plug at an
angle from below, unlock by pressing together, and remove
the plugs from the connection for external audio sources Pos.
-4-.
Release from catches -arrows- and remove USB connection
-2- and external audio sources connection -5-.
Installing
7. Connections for audio/video signal MEDIA IN (multimedia socket) external source 55

8 SmartGate system
8.2 SmartGate system - check the correct function,
page 57
8.3 Remove and install control unit for information electronics
2 J829 (SmartGate), page 58
8.4 Set the parameters for the Wi-Fi connection, page 59
8.5 Update firmware, page 60
8.1 General points

SmartGate system
The SmartGate system offers the possibility to access the
driving data via the wireless Wi-Fi connection.
This is one-way communication of the connected communi
cations of the customer's equipment (e.g., cell phone, tablet,
laptop) with the control unit for the SmartGate system.
The driving data received can then be processed (depending
on the application used and installed on the communications
equipment).
The Wi-Fi range is limited to the interior of the vehicle.
One part of the system is the control unit for information elec
tronics 2 - J829- located under the driver's seat.
For a detailed description of the functions, operations and
connection see the Octavia III Owner's Manual .
Caution
Correct communication within the scope of the SmartGate sys
tem relies on the customer's communications equipment (e.g.,
cell phone/tablet) functioning correctly, and on the software
applications being installed.
Not every cell phone/tablet is compatible within the scope of
the SmartGate system.
For details of mobile phone/tablet compatibility, and the avail
able applications, visit the KODA website (www.skoda-
auto.com).
KODA AUTO a.s. assumes no responsibility for any problems
due to incompatibility or improper function of cell phones/tab
lets or the applications installed on them

8.2 SmartGate system - check the correct

function
Caution

tem relies on the customer's communications equipment (e.g.,
cell phone/tablet) functioning correctly, and on the software
applications being installed.
auto.com).
KODA AUTO a.s. assumes no responsibility for any problems
due to incompatibility or improper function of cell phones/tab
lets or the applications installed on them
For a detailed description of the functions, operations and con

nection see the Octavia III Owner's Manual .
The correct function of the SmartGate system is verified by the
device itself.
For example, the following can be used to verify the correct func
tion: Vehicle diagnostic tester, mobile phone, tablet, laptop,
referred to as "communication devices" below.
For the connection, ask the customer for the PIN code (password)
for the SmartGate system.
Connecting with a Wi-Fi device
Preconditions:
Switch on Wi-Fi on the connected communications equipment
Switch on the ignition
Open a connection to SmartGate (login to a Wi-Fi network)
Search for available Wi-Fi connections on the connected com
munications equipment SmartGate identifies the connected
communications device as SmartGate_...
The last six symbols of the vehicle identification number (VIN
code) are displayed at the position....
Enter the password supplied by the customer, for the initial
connection, enter the 17 digits of the vehicle identification
number (VIN) (in uppercase).
Note
If no PIN code (password) is available, then switch off the ig

nition and, if necessary, disconnect the battery earth strap or
the connector on the SmartGate unit for approx. 30 seconds.
After re-connecting the battery earth strap, switch on the igni
tion and enter
Protected theCopying
by copyright. vehicle identification
for private or commercialnumber (inpartuppercase)
purposes, in or in whole, is not permitted
asunless
the PIN code.
Up to four communications devices can be connected to the
SmartGate system at the same time.
8. SmartGate system 57
Connection problems
If the connection fails, then check the following points.
Are the conditions for a successful connection fulfilled?
Does SmartGate show up in the list of available Wi-Fi net
works?
Was password required for validating the connection entered
correctly?
Is the communications equipment to be connected possibly
still connected to another Wi-Fi network?
If the above points are okay, and the connection still fails, then
check the state of the LED display on the control unit for informa
tion electronics 2 - J829- (SmartGate) located under the driver's
seat.
If the LED display -arrow- on the control unit:
is unlit or lit red, the device is not OK, check the electrical wiring
as per Current flow diagrams, Electrical fault finding and
Fitting locations; if needed, replace the SmartGate control unit
red flashing - this is a self-test, wait for the test to complete (on
initial activation)
lit green the device is OK, no user is connected
green flashing - the device is OK, at least one user is connec
ted and the SmartGate application is active on the connected
communication device (if you connect without an active appli
cation - the LED display is lit green)
flashing red and green - the device is OK; and still in production
mode (indicates production mode, for example in Production,
where multiple vehicles with SmartGate exist at one location)
orange (red and green at the same time) the device is in
upgrade mode, wait for this mode to complete
Disconnecting
The connection to SmartGate can be disconnected in one of the
following ways:
by disconnecting the connection to SmartGate on the connec
ted communications device
by disabling Wi-Fi on the connected communications device
by switching off the ignition and removing the ignition key for
more than 5 s (for vehicles with an ignition starter switch, by
switching off the ignition and opening the driver door)
8.3 Remove and install control unit for infor

mation electronics 2 - J829- (Smart
Gate)
Removing Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
The control unit for information electronics 2 - J829- (SmartGate)
is fastened under the driver's seat on the floor covering by means

of a Velcro fastener.
Move the driver's seat as far back and up as possible.

Remove the perforated floor covering and the control unit -1-
from the Velcro fastener and, taking the lengths of the con
nected cables into consideration, remove the unit.
To pull off the connector, press the latch -1-, and release the
connector by tilting out the bar -arrow-.
Install
following points:
Installation position of the control unit, see figure.
Do the following when replacing the control unit:
Update firmware 8.5 Update firmware, page 60
Check functionality
8.2 SmartGate system - check the correct function,
page 57
8.4 Set the parameters for the Wi-Fi con

nection
Some properties of the Wi-Fi connection can be changed and
configured using the connected communications device (e.g.,
Vehicle diagnostic tester, cell phone, tablet, laptop).
After fulfilling the conditions for a successful connection, enter the
address "HTTP://192.168.123.1/index.html" in the web browser
of the connected communications device. You will see a menu for
setting the parameters for the SmartGate Wi-Fi connection.
Configuration options:
SSID
Channel (1 to 10) manual setting of the connection channel
Security setting the security level for the connection
Open unencrypted connection, no password entry required
on the device to be connected; the connection is set up auto
matically
WPA or WPA2 encrypted connection
WPA/WPA2 key - password input
Transmitting power in % - sets the signal strength in percent
DHCP (lease time) - time for which the IP address remains
valid
Web interface: port - web interface
If you change the connection encryption from unsecured (open)
to secured WPA or WPA2, you must enter a password on the
communications equipment to be connected.
If no PIN code (password) is available, then switch off the ignition
and, if necessary, disconnect the battery earth strap or the con
nector on the SmartGate unit for approx. 30 seconds. The Smart
Gate is reset to the factory default settings and transmission

encryption is set to WPA2.
After re-connecting the battery earth strap, switch on the ignition
and enter the vehicle identification number (in uppercase) as the
PIN code.
8.5 Update firmware

To update the SmartGate firmware, you can use, e.g., Vehicle
diagnostic tester cell phones, tablets, laptops, mobile phones; re
ferred to as communications devices in the following.
Caution

tem relies on the communications device functioning correctly,
and on the software applications being installed.
auto.com).
The firmware update function is not available in the Internet
Explorer web browser version 9 and older.
Update data from the KODA website are needed for the firm
ware update.
During the entire upgrade process, make sure that the ignition is
on, or the engine is running (avoid starting the engine during the
upgrade procedure).
Update procedure:
Download the update data for SmartGate from the KODA
website; save them on the communications device (one file).
Switch on Wi-Fi on the communications device.
Switch on the ignition and start the engine.
Connect the communications device with SmartGate.
Open the web browser on the communications device, and
enter the address "HTTP://192.168.123.1/index.html".
At the bottom of the SmartGate menu that appears, select the
firmware upgrade menu item.
Select the update data stored on the communications device.
Pressing "start update" copies the update data to SmartGate
(copying takes about 5 min).
After downloading the data and confirming "perform update",
the update starts (the update process takes approx. 2 min).
After completing firmware update, the SmartGate is restarted.

Note
During the update process, the LED display on the control unit
for information electronics 2 - -J829-- lights up orange (red and
green at the same time).
After completing the update, and restarting the SmartGate, the
LED display lights up green, see page 58 .
92 Windscreen wash/wipe system

1 Windscreen and rear window wiper
system
1.1 Removing and installing the washer pump and washer fluid
reservoir, page 62
1.2 Removing and installing the spray nozzles for windscreen
washer system, page 63
1.3 Removing and installing the spray nozzle for rear window
washer system, page 64
1.4 Repairing washer fluid level pipes, page 65
1.1 Removing and installing the washer

pump and washer fluid reservoir
The function of the windscreen washer system can be checked
with the Vehicle diagnostic tester via the final control diagnosis
of the vehicle voltage control unit - J519- .
Removing
Note
Depending on the version, the positions ofcopyright.

Protected by the individual
Copying for compo
private or commercial purposes, in part or in whole, is not permitted
nents and the hose connection can differ
unless slightly
authorised fromAUTO
by KODA the version
A. S. KODA AUTO A. S. does not guarantee or accept any liability
in the illustrations. The removal occurs in the same way.

Remove the front left wheelhouse liner Body Work; Rep.
gr. 66 .
Release plug from the washer fluid pumps for windscreen
-5-, for headlight -2- and from sensor for washer fluid level
-4-.
Expose wiring loom -3-.
To unlock turn the locking clip on the hose connections -7-
(black marking front windscreen washer) and -6- (white
marking rear windscreen washer) and disconnect the con
nections from the washer fluid pump. Collect the flowing out
washer fluid in a suitable vessel.
Release washer hose for headlight -1- by pressing the locking
clip and detach.
If necessary, push the washer fluid pumps out of the washer
fluid vessel upwards out of the rubber bracket.
Remove front left headlight
1.2 Removing and installing headlight, page 80 .
62 Rep. gr.92 - Windscreen wash/wipe system

Remove expansion clip -1- and push filler neck -3- with filler
pipe -4- out of the bracket -2-.
Screw out nut -arrow- (8 Nm).
Screw out nuts -1- and -3- (8 Nm)

Screw out the vessel -2- from the stud bolt -arrow A- and lower
-arrow B-.
Installing
Hoses with angled pieces must click audibly into the connec
tions on the washer fluid pumps.
After completing the assembly work bleed the headlamp
cleaning system
2.3 Bleed the headlamp cleaning system, page 67 .
1.2 Removing and installing the spray noz

zles for windscreen washer system
Removing
Remove windscreen wiper arms
3.2 Removing and installing the wiper arms with wiper
blades and setting their final setting, page 68 .
1. Windscreen and rear window wiper system 63

Remove the cooling water tank cover Body Work; Rep. gr.
66 .
Carefully lever the angled pieces off the spray nozzles from
below and disconnect the plug connections (of the heated
nozzles).
Unclip the nozzles from the cooling water tank cover.
Installing
Perform a functional check or adjust nozzles Maintenance ;
Booklet Octavia III .
1.3 Removing and installing the spray noz

zle for rear window washer system
1.3.1 Octavia, page 64
1.3.2 Octavia Combi, page 64
1.3.3 Octavia Combi GreenLine, page 65
1.3.1 Octavia
Remove nozzle
Run wiper until it is in park position.
Fold down cover cap of rear window wiper -1-.
Carefully pull out spray nozzle -2- -arrow-.
Installing
Run wiper until it is in park position, insert the spray nozzle in
the correct position in the wiper motor shaft.
Perform a functional check or adjust nozzles Maintenance ;
1.3.2 Octavia Combi unless authorised by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
Remove nozzle
Remove lamp for high level brake light
6.2 Removing and installing the high level brake light - Oc
tavia Combi, page 111 .
Unlock the latches -arrows- and remove the spray nozzle -1-
out of the light towards the rear.
Install
After installation, test function and adjust nozzles Maintenance ;

1.3.3 Octavia Combi GreenLine

The nozzle is protected against dirt and is part of the spoiler. The
nozzle cannot be used separately.
1.4 Repairing washer fluid level pipes

Workshop Manual Electrical System General notes Elec
trical System General notes; Rep. gr. 92 .
1. Windscreen and rear window wiper system 65

2 Headlamp cleaning system

2.1 Removing and installing headlight cleaning system pump
V11 , page 66
2.2 Removing and installing the lift cylinder for spray nozzles
of headlight, page 66
2.3 Bleed the headlamp cleaning system, page 67
Summary of components Components of the headlight washing
system Electronic Catalogue of Original Parts .
2.1 Removing and installing headlight

cleaning system pump - V11-
Removing and installing the pump is described in
1.1 Removing and installing the washer pump and washer fluid
reservoir, page 62 .
After installing the pump bleed the headlamp cleaning system
2.2 Removing and installing the lift cylinder

for spray nozzles of headlight
Press out the spray nozzles with the cover from the bumper
from the inside so that the cover can be grabbed.
Remove the cover a little, then grab the spray nozzles and pull
out as far as the stop.
Unclip the cover -1- from the bearing -arrows-.
Press off the catches -arrows A- using a small screwdriver and

push the lift cylinder -1- out of the bumper -arrow B-.
Installing
Push the lift cylinder into the brackets in the bumper until it
clicks audibly into place.
Hoses with angled pieces must click audibly into the connec
tions on the lift cylinders for spray nozzles.
Install bumper.
After completing the assembly work bleed the headlamp
cleaning system

2.3 Bleed the headlamp cleaning system

After installation or when it is first put into service the headlamp
cleaning system must be bled, in order to guarantee a perfect
operation.
Top up windscreen and headlight washer reservoir.
Start engine.
Switch on headlight.
Operate headlamp cleaning system several times (3 5 pul
ses for an operating duration of each 3 s).
If necessary repeat this bleeding procedure until a perfect
functioning of the lift cylinders for headlamp cleaning system
and for spray nozzles is achieved.
2. Headlamp cleaning system 67

3 Windscreen wiper and washer sys

tem
3.1 Fault recognition and fault display, coding, page 68
3.2 Removing and installing the wiper arms with wiper blades
and setting their final setting, page 68
3.3 Removing and installing wiper motor with linkage,
page 70
3.4 Removing and installing Sensor for rain and light detection
G397 , page 71
3.5 Repairing the rain and light detector sensor G397 , Valeo
manufacturer, page 73
3.1 Fault recognition and fault display, cod

ing
The wiper motor control unit - J400- and the windscreen wiper
motor - V- are installed as one component and cannot be re
placed separately.
The vehicle voltage control unit - J519- , which regulates the
functions of the windscreen wiper and washer system, is equip
ped with self-diagnosis which facilitates the fault finding.
Use the Vehicle diagnostic tester for troubleshooting and cod
ing.
3.2 Removing and installing the wiper arms

with wiper blades and setting their final
setting
Notewith respect to the correctness of information in this document. Copyright by KODA AUTO A. S.
If the wiper motor is switched on during work, the front flap must
be closed and the ignition must be switched on, otherwise the
voltage supply of the wiper motor is interrupted.

Extractor for wiper arms - T10369/1-
Removing
Lever off caps -3- using screwdriver.

Unscrew the nuts -2- by a few turns.
Push the extractor for wiper arms -T10369/1- , as shown, onto

the arm.
Note
To release the wiper arm, always use the thrust piece -2- in order
to avoid damage to the thread of the wiper motor shaft.
Release the wiper arm -1- from the shaft by turning the pres
sure screw -3-.
Unscrew nuts and remove arms.
Installing
Note
When switching off for the second time, the wiper motor over
runs in the offset final setting so that the wiper blade lip is
controlled in the other direction.
The wiper motor runs downwards and then again a little up
wards. This offset final setting cannot be used to compensate
for the windscreen wiper crank.
The final setting must be used in which the wiper motor runs
directly and without overrun in the lower final setting. If the
wiper motor runs in the offset final setting, wiping must be
switched on again.
Function of the offset final setting is active only after 100 wiper
cycles as of coding or installation of a new wiper motor. If this
function is already activated, it can be determined by switching
on and off the wiper motor repeatedly.
Switch wiper motor on and off and run until it is in park position
for setting the windscreen wiper arms.
3. Windscreen wiper and washer system 69

Insert windscreen wiper arms with wiper blades and align wip
er blades to the markings in the windscreen -1-.
Slightly tighten fixing nuts.
Operate the flick wipe and check again or correct the setting
of the wiper arms.
Tighten securing nuts (21 Nm).
Note
The tolerance between wiper blade and marking -1- is 2 mm.
3.3 Removing and installing wiper motor

with linkage
Removing
Remove wiper arms with wiper blades
3.2 Removing and installing the wiper arms with wiper
blades and setting their final setting, page 68 .
66 .
Unscrew screws -1-, -3- and -5-.
Insert wiper motor with linkage -2-into the plenum chamber.
Installing
First, slightly tighten screws by hand in the -1 -, -2- and -3-

order.
Then tighten in the same order to 8 Nm.

3.4 Removing and installing Sensor for rain

and light detection - G397-
Caution
If the sensor for rain and light detection - G397- is removed

from the retaining plate on the windscreen (e.g. when changing
the windscreen), it can be subsequently installed again. Store
the removed sensor dust-free until it is installed again and
make sure that the silicone coupling cushion does not get dirty.
Removing
Note
To facilitate removal, turn the mirror as necessary.

Remove covers from the Sensor for rain and light detection -
G397- Body Work; Rep. gr. 68 .
Release retaining clip -1- -arrow-.
Note
Observe a waiting time of at least 1 minute after releasing the

retaining clip. This allows the silicone layer to expand so that it
will not be damaged while it is being removed.

Carefully lever the sensor for rain and light detection - G397-
Pos. -2- out of the retaining frame from above starting from the
front windscreen.
Release connector -1- and pull off.
Installing
Caution
Thoroughly clean the windscreen inside the retaining plate

with e.g. isopropyl (technical alcohol).
The surface (coupling cushion) of the sensor must not get
dirty or damaged when installing. A sensor with a dam
aged coupling cushion must be replaced.
There are several variants of sensors (depending on
equipment). Ensure that the correct component is used for
replacement, see Electronic Catalogue of Original
Parts .
Note
If the surface (coupling cushion) of the sensor is dirty, it can be

cleaned, if necessary, by sticking on one or several adhesive
tapes and then pulling them off again.
If a new sensor is installed, press the grips in

-direction ofProtected
arrowbyA- and remove the protective cap -1- in
-direction ofunless
arrow B-. by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
authorised
Mount plug.
Insert the sensor into the retaining frame on the windscreen.
Press retaining clip -1- on until the catches -arrow- audibly

click into place.
Note
Even after correct installation of the sensor, smaller air bub

bles can be present initially between the windscreen and the
coupling cushion. After approx. 10 min, the contact surface
must be free of bubbles.
If the contact surface is not free of bubbles after 10 minutes,
the rain sensor must be removed and re-installed.
Air bubbles between the windscreen and the coupling cushion
cause sensor malfunctions.
When replacing, the new sensor must be coded with the Ve

hicle diagnostic tester.

3.5 Repairing the rain and light detector

sensor - G397- , Valeo manufacturer
Note
There are various bushings for the Rain and light detector
sensor - G397- from different manufacturers.
Sensor bushing with optical unit is also supplied with retaining
clips as a spare part. These must be removed for vehicles that
do not require retaining clips.
Work procedure
Remove the sensor
3.4 Removing and installing Sensor for rain and light de
tection G397 , page 71 .
Carefully remove the silicone cushion -2- or the residues from
the sensor -1-.
Caution
The surface of the sensor must be completely free of foil resi

dues.
Clean the sensor surface with cleaning solution.
Remove the silicone paper -3- from the cushion -2-.

Transparent protective foil -1- stays on the cushion -2- to begin
with as assembly film.
Attach the cushion -2- with the protective foil -1- to the sensor
-3-.

Press the cushion onto the sensor -2- through the transparent
foil -1-, so that there are no bubbles between the foil and sen
sor.
Carefully pull the transparent protective foil -1- off the cushion
-2-.
Install the Rain and light detector sensor - G397-
3.4 Removing and installing Sensor for rain and light de
tection G397 , page 71 .

4 Rear window wiper system

4.1 Removing and installing the wiper arm with wiper blade
and setting its final setting, page 75
4.2 Removing and installing rear window wiper motor,
page 76
4.1 Removing and installing the wiper arm

with wiper blade and setting its final set
ting
Removing
Move wiper to park position.
Unclip the cap -1- from the catch pegs and fold down.
Carefully slide out the nozzle -2- -arrow- (does not apply to
Octavia Combi).
Screw out the nuts -arrow- a few turns so that it is in a line with
the upper edge of the shaft.
Using a standard commercially available small two-arm ex

tractor -1-, undo the wiper arm from the shaft.
Remove nut -2- and remove the wiper arm -3-.
Installing
When the ignition is switched on, switch wiper motor on and
off and run until it is in park position.
Position wiper arm and loosely secure with nut.
4. Rear window wiper system 75
Set final position of wiper arm in accordance with the figure.

The value -a- is:
Octavia - 522 mm
Octavia Combi - 452
Tighten fixing nut (12 Nm).
Install nozzle (not valid for Octavia Combi).
Perform a functional and setting check.
4.2 Removing and installing rear window

wiper motor
Remove wiper arm with wiper blade
4.1 Removing and installing the wiper arm with wiper blade
and setting its final setting, page 75 .
Remove the bottom tailgate trim panel Body Work; Rep. gr.
70 .
To unlock turn the locking clip on the hose connections and
pull off the hose -2-.
Unscrew nuts -arrows- (7 Nm) and remove wiper motor -1-.
Take fitting position of implementation into account:
Octavia:
Recess in the rear window implementation -arrow- is located

at the bottom, from the inside, see Fig.
Octavia Combi:

Recess in the rear window implementation -arrow- is located

at the top, from the outside, see Fig.
4. Rear window wiper system 77

94 Lights, bulbs, switches - exterior

1 Headlights halogen headlights
1.1 Summary of components of headlight, page 78
1.2 Removing and installing headlight, page 80
1.3 Adjusting headlights, page 80
1.4 Replacing light bulbs in headlights, page 81
1.5 Replace headlight fixing brackets, page 83
1.6 Change headlight for right-hand and/or left-hand traffic,
page 84
1.7 Removing and installing headlight range control motor,
page 85
1.1 Summary of components of headlight

Description of function and types of headlights to be fitted:
sentation
tions
78 Rep. gr.94 - Lights, bulbs, switches - exterior

1 - Headlight housing
1.2 Removing and in
stalling headlight,
page 80
adjust
1.3 Adjusting head
lights, page 80
2 - Bulb for main beam light,
daytime running light and side
light
12 V, 55 W (H15)
Renew
1.4 Replacing light
bulbs in headlights,
page 81 .
3 - Cover
4 - Headlight range control mo
tor
1.7 Removing and in
stalling headlight range
control motor,
page 85
5 - Bulb for low beam light
12 V, 55 W (H7)
Renew
1.4 Replacing light
bulbs in headlights,
page 81 .
6 - Cover
7 - Bolts
1.5 Nm
8 - Cover
9 - O-ring
10 - Light bulb for the turn signal light
PWY24W
Renew 1.4.3 Replacing bulb PYW24Y for the turn signal light, page 82 .
Note
The headlight wiring loom spare part is only used as a source for
spare parts (e.g. connector, fitting etc.). It therefore cannot be re
placed completely in the headlight.
1. Headlights halogen headlights 79


Removing
Note
The removal and installation will be demonstrated using the ex

ample of the left-hand headlight. The removal and installation of
the right headlight follows the same principle.

Remove bolts -arrows-.
Carefully push the headlight -1- towards the front, for this step
disconnect the plug.
Installing
Align the headlight according to the contours of the vehicle
body (maintain the gap size Body Repairs; Rep. gr. 00 ) and
loosely tighten with screws.
Install bumper.
By turning -arrow- the setting elements -4-, the headlight is

moved and thereby fitted to the surrounding body parts.
Then tighten securing bolts in sequence -1-, -2- and -3- (3.5
Nm).
Note
The setting element is aligned automatically when tightening the

screw -1-.
Set up the headlight 1.3 Adjusting headlights, page 80 .
1.3 Adjusting headlights

Use a headlight beam setting device for setting the headlight
beam. Specified values, setting elements, conditions and meas
urement Maintenance ; Booklet Octavia III .

1.4 Replacing light bulbs in headlights

1.4.1 Replacing H7 bulb for low beam light, page 81
1.4.2 Replacing the multifunctional bulb H15 (for main beam
light, daytime running light, side light), page 82
1.4.3 Replacing bulb PYW24Y for the turn signal light,
page 82
1.4.1 Replacing H7 bulb for low beam light
WARNING
The H7 light bulb is pressurized and can burst when changing

the bulb. It is recommended to wear gloves and safety glasses
when changing bulbs.
Note
Do not touch the glass when installing the light bulb. Your fin
gers will leave traces of grease on the glass which then
evaporate when the bulb is switched on causing it to cloud.
Pay attention to the correct fitting and undamaged seals on
the plastic covers. Water ingress will
Protected by destroy
copyright. theforheadlight.
Copying private or commercial purposes, in part or in whole, is not permitted
Remove cover -1-.
Release and remove the bulb -2- from the catches by pendular
movement and pulling force -arrows-.

1.4.2 Replacing the multifunctional bulb H15

(for main beam light, daytime running
light, side light)
WARNING
The H15 light bulb is pressurized and can burst when changing
the bulb. It is recommended to wear gloves and safety glasses
when changing bulbs.
Note
the plastic covers. Water ingress will destroy the headlight.

Remove cover -2-.
Turn the bulb -1- to the left -arrow- and remove from the head
light housing.
1.4.3 Replacing bulb PYW24Y for the turn sig

nal light
Note
For changing the bulb of the turn signal light, a repair kit is
supplied light bulb, O-ring, cap and fixing screws.


Remove the headlight with the defective light bulb
Lever off lens for signal bulb -1- using a screwdriver. Proceed
carefully so that the remainders of the cover do not grip into
the headlight housing.
Turn bulb socket -arrow- and remove from the headlight.
Disconnect the plug -2- and replace the defective light bulb.
After installing the new light bulb -4- attach the cap -2- with the
O-ring -3- with screws -1- (1.5 Nm).
1.5 Replace headlight fixing brackets

If the headlight fixing brackets are broken or damaged, they can
be replaced by installing the repair kit. The complete headlight
must not be replaced.
Note
Before repairs check if the headlight has no other damage, as

the repair would be senseless.
The replacement brackets can be ordered separately see
Electronic Catalogue of Original parts . There are no fixing
screws in the repair kit.
Before repairs the headlight must be removed
After installing the headlight, adjust the headlight
1.3 Adjusting headlights, page 80 .
Detach the remainder of theto the
with respect original bracket.
correctness of information in this document. Copyright by KODA AUTO A. S.
Change the contact surface (grind off, remove by file) to allow

a new bracket to be inserted properly.

Insert a new bracket true to form -arrows-.
Note
The attachment brackets as spare parts do not have openings for

fixing screws.
Insert the fixing screws directly into the bracket and tighten
(1.5 Nm). The screws cut a new thread into the bracket.
1.6 Change headlight for right-hand and/or

left-hand traffic
The halogen headlights should have self-adhesive foil glued over
them when driving in countries which drive on the right or the left
thereby preventing blinding of the drivers travelling in the opposite
direction.
Note
The change of the headlights is not suitable for the permanent

mode, rather only as a brief touristic solution during a tem
porary journey abroad.
Both headlights must always be changed.
The lenses must be cleared of dirt and de-greased, e.g. with
degreased white spirit solution, before sticking the foil.
When cleaning and gluing foils, the lens must remain cold for
safety reasons.
The instructions right and/or left on the protective foils al
ways refer to the front visibility towards the outside.
Ensure that the correct protective foil is chosen, see Elec
tronic Catalogue of Original Parts.
Remove the rear protective foil.

Place the foil on the headlight in such a way that the lower and
outer vertical edge of the auxiliary part of the foil is offset with
the bottom edge of the lens and the vertical auxiliary contour
on the headlight panes, see Fig.
1- The headlight on the right
2- The headlight on the left
Left-hand drive:

Right-hand drive:
Forcefully press on the middle area of the foil -B-.
Carefully pull off the auxiliary part of the foil -A- from the head
light.
Only a part of the protective foil remains on the lens -B-.
Note
Inform the customer about the corresponding notes for removing

the residual glue after pulling off the protective foil, e.g. textiles
soaked in isopropyl alcohol (do not use any aggressive solvent,
which can damage the polycarbonate lenses).
1.7 Removing and installing headlight range

control motor
Removing
Remove the headlight from which the control motor is removed
Remove cover -2-.
The headlight on the left:
Carefully knock out and remove the plug -2-.

Release securing bolts underneath the plugs.
Note
The bolts beneath the plugs are not exactly in the opening axle -
for this reason, the control motor -1- needs to be swivelled out a
little -arrow-.
The headlight on the right:
Carefully knock out and remove the plug -3-.

Undo the screw underneath the plug and the bolt -2-.
Note
The bolt beneath the plug are not exactly in the opening axle - for
this reason, the control motor -1- needs to be swivelled out a little
-arrow-. To release the bolt -2- use a flexible approach, using a
smaller Torx where necessary.
Both headlights:

Move the control motor -1- in the direction of arrow -A-, undo
the pressure element from the groove, and remove in the di
rection of arrow -B-.
Install
following points:
Broken-out plugs -2- must be replaced by new plugs, see

Electronic Catalogue of Original Parts .
After installing the control motor, check the function is correct.

2 Headlights Bi-xenon headlights

2.2 Assembly overview - Bi-xenon headlights, page 88
2.3 Summary of components Bi-xenon headlights with LED
module, page 90
2.4 Removing and installing headlight, page 91
2.5 Replacing light bulbs and gas discharge lamps,
page 91
2.6 Change headlight for right-hand / left-hand traffic,
page 94
2.8 Replace headlight fixing brackets, page 94
2.9 Removing and installing control unit for gas discharge lamp
J343 left or J344 right, page 94
2.10 Remove and install performance module for the headlight
J667 left or J668 right, page 95
2.11 Removing and installing Control unit for daylight driving
light and side light J860 (LED module) left and J861 right,
page 95
2.12 Removing and installing the cornering light and headlight
range control unit J745 , page 95
2.13 Vehicle level sensor G78 front left or G76 rear left , page
97
2.14 Removing and installing headlight range control motor,
page 97
WARNING
Mortal high voltage, risk of injury and risk of pollution.

Observe the use and safety instructions for the gas discharge
lamps in the Workshop Manual Electrical System - general
notes Electrical System - general notes; Rep. gr. 94 .
Note
When handling a fault it is absolutely essential to know the func

tion and operation of the headlights.
The headlights with Xenon discharge lamps are Bi-Xenon lamps

(AFS Adaptive Frontlighting System)
Protected by copyright. and
Copying for have
private automatic
or commercial head
light range control.
The cornering light and headlight range control unit - J745- eval
uates the following entry information:
Steering wheel angle and direction
Vehicle speed
Reversing lights on
Switching on the headlight (low beam light or main beam light)
2. Headlights Bi-xenon headlights 87

Signals of vehicle level sensors on front and rear axle

individual wheel speeds
Position of the light switch
On the basis of this information, it controls the rotary and inclina
tion movement of the headlights.
2.12 Removing and installing the cornering light and head
light range control unit J745 , page 95 .
2.13 Vehicle level sensor G78 front left or G76 rear left ,
page 97 .
Further information, description of function and types of head
lights to be fitted:
sentation
tions
2.2 Assembly overview - Bi-xenon headlights
1 - Control unit for gas dis

charge lamp - J343- left or -
J344- right
2.9 Removing and in
stalling control unit for
gas discharge lamp
J343 left or J344 right,
page 94
is the same as for the
halogen headlight
1.2 Removing and in
stalling headlight,
page 80
adjust
1.3 Adjusting head
lights, page 80
3 - Bulb for side light and day
time running light
12 V, 21/5 W (P21/5W)
Renew
2.5.2 Replacing
bulbs for side light and
daytime running light
P21/5W, page 92 .
4 - Cover
tor
2.14 Removing and
installing headlight Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
range control motor, unless authorised by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
page 97

6 - Gas discharge lamp with integrated ignition coil

42V, 35 W (type D3S)
Renew 2.5.4 Replacing the gas discharge lamp , page 93 .
7 - Cover
8 - Bolts
1.5 Nm
9 - Lens for signal bulb
10 - O-ring
PWY24W
12 - Performance module for the headlight - J667- left or -J668- right
2.10 Remove and install performance module for the headlight J667 left or J668 right, page 95

2.3 Summary of components Bi-xenon headlights with LED module
Note
LED module is defined for side light and daytime running light.
The LED module is integrated into the headlight housing and cannot be changed separately.
1 - Control unit for gas dis

charge lamp - J343- left or -
J344- right
2.9 Removing and in
stalling control unit for
gas discharge lamp
J343 left or J344 right,
page 94
is the same as for the
halogen headlight
1.2 Removing and in
stalling headlight,
page 80
adjust
1.3 Adjusting head
lights, page 80
3 - Light bulb for additional side
light
12V, 5W (W5W BL)
Renew
2.5.1 Replacing light
bulb for additional side
light, page 91 .
4 - Cover
tor
Removing and installing Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
2.14 Removing and unless authorised by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
installing headlight
range control motor,
page 97
6 - Gas discharge lamp with in
tegrated ignition coil
42V, 35 W (type D3S)
Renew 2.5.4 Replacing the gas discharge lamp , page 93 .
7 - Cover
8 - Bolts
1.5 Nm
9 - Lens for signal bulb
10 - O-ring
PWY24W

12 - Control unit for daylight driving light and side light - J860- (LED module) left or -J861- right
2.11 Removing and installing Control unit for daylight driving light and side light J860 (LED module)
left and J861 right, page 95
13 - Performance module for the headlight - J667- left or -J668- right
2.10 Remove and install performance module for the headlight J667 left or J668 right, page 95

Removal and installation is done in the same was as for the hal
ogen headlight, see
2.5 Replacing light bulbs and gas discharge

lamps
2.5.1 Replacing light bulb for additional side light, page 91
2.5.2 Replacing bulbs for side light and daytime running light
P21/5W, page 92
page 93
2.5.4 Replacing the gas discharge lamp , page 93
The LED module is integrated into the headlight housing and
cannot be changed separately. Replace headlight if there is a
module fault.
2.5.1 Replacing light bulb for additional side

light
Note with respect to the correctness of information in this document. Copyright by KODA AUTO A. S.
the plastic covers as well as the correct positioning of the cov
er. Water ingress will destroy the headlight.
Headlights with LED module.

Remove cover -2-.

Take hold of bulb socket -1- and remove it while observing the
connected cable lengths -arrow-.
Remove bulb -2- from holder -1-.

After replacing the bulb, press socket and bulb fully into the
headlight and install cover.
2.5.2 Replacing bulbs for side light and day

time running light P21/5W
Headlights without LED module.

Remove cover -2-.

Turn socket with bulb -1- -arrow- and remove.

Replace defective light bulb.
2.5.3 Replacing bulb PYW24Y for the turn sig

nal light
The work sequence is the same as when changing the halogen
headlight
page 82 .
2.5.4 Replacing the gas discharge lamp
WARNING
Mortal high voltage, risk of injury and risk of pollution.

Observe the use and safety instructions for the gas discharge
lamps in the Workshop Manual Electrical System - general
notes Electrical System - general notes; Rep. gr. 94 .
Note
Do not touch the glass bulb when installing. Your fingers will
leave traces of grease on the glass bulb, which then evaporate
when the gas discharge lamp is switched on causing the glass
bulb to cloud.
Switch off thewith
ignition
respect toand all electrical
the correctness components.
of information in this document. Copyright by KODA AUTO A. S.
Unplug the connector from the headlight.

Remove cover -1-.

Press the peg at the plug for unlocking and remove the plug
-2- towards the bottom.
Turn gas discharge lamp by approx. 45 -arrow- and remove
from the headlight housing.
Installing
Inspecting the headlight beam setting Maintenance ; Book
let Octavia III .
Undertake the basic setting for beam range regulation Ve
2.6 Change headlight for right-hand / left-

hand traffic
The position of the ray of light should be adjusted when driving in
countries which drive on the right or the left thereby preventing
blinding of the drivers travelling in the opposite direction.
Headlights with Xenon discharge lamps are repositioned in the
information display selection list, see Infotainment operating
manual , Chapter Setting vehicle systems (CAR button).

The automatic headlight range control, cornering light and the
onboard supply control unit are equipped with the self-diagnosis
that facilitates the fault finding of the headlights.
2.8 Replace headlight fixing brackets

The work sequence is the same as when changing the halogen
headlight 1.5 Replace headlight fixing brackets, page 83 .
2.9 Removing and installing control unit for

gas discharge lamp - J343- left or -J344-
right
Removing
Remove headlight
Screw out the screws -arrows- (1.4 Nm) and remove the con
trol unit -1-.
Release and disconnect the plug connections.
Install
Installation is performed in the reverse order, pay by
Protected attention to thefor private or commercial purposes, in part or in whole, is not permitted
copyright. Copying
following points: unless authorised by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
Note
Correctly install the seal when installing the unit. Water ingress
will destroy the headlight.

2.10 Remove and install performance mod

ule for the headlight - J667- left or -J668-
right
Removing
Remove headlight
Unscrew screws -2- (1.4 Nm) and remove the control unit
-1-.
Release connector and pull it off.
Installing
Note
If the performance module was replaced, then the coding must

be carried out with Vehicle diagnostic tester and the head
lights need adjusting page 80 .
2.11 Removing and installing Control unit for

daylight driving light and side light -
J860- (LED module) left and -J861- right
Removing
Left side- remove headlight
Right side- remove the front right wheelhouse liner Body
Work; Rep. gr. 66 .
Unscrew screws -3- (1.4 Nm) and remove the control unit
-4-. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Installing with respect to the correctness of information in this document. Copyright by KODA AUTO A. S.

Note
2.12 Removing and installing the cornering

light and headlight range control unit -
J745-
2.12.1 Left-hand drive, page 95
2.12.2 Right-hand drive, page 96
2.12.1 Left-hand drive

The control unit is located above the brake pedal.

Note
If the control unit is replaced, Vehicle diagnostic tester connect

and, in the operating mode Targeted fault finding, select the
Replace control unit function of the relevant control unit.
Removing
Remove the knee airbag Body Work; Rep. gr. 69 .
Removing the left footwell vent on the driver side Heating,
Air Conditioning; Rep. gr. 80 .
Remove the bearing bracket for the brake pedal Suspen
sion; Rep. gr. 46 .
Push out bolt and remove expansion clips -3-.
Lower unit -1-, unlock and disconnect plug connection -2-.
Installing
2.12.2 Right-hand drive

The control unit is located above the brake pedal.
Note
If the control unit is replaced, Vehicle diagnostic tester connect

and, in the operating mode Targeted fault finding, select the
Replace control unit function of the relevant control unit.
Removing
Remove the storage compartment in the dash panel on the
front passenger side Body Work; Rep. gr. 70 .


Remove expanding rivets -2- and remove unit -1-.
Install
2.13 Vehicle level sensor - G78- front left or -

G76- rear left
The vehicle level senders are an integral part of the headlight
range.
The assembly work is described in the Workshop Manual
Chassis .
Install front left vehicle level sensor - G78- Chassis; Rep.
gr. 40
Install rear left vehicle level sensor - G76- Chassis; Rep.
gr. 42

control motor
Removing
Remove the headlight from which the control motor is removed
Remove cover -1-.

To access the fixing screw, carefully knock out and remove

the plug -arrow-.
To be able to see the headlight range control motor better,
remove the Control unit for daylight driving light and side light
- J860- (LED module -1-
2.11 Removing and installing Control unit for daylight driv
ing light and side light J860 (LED module) left and J861 right,
page 95 .
Remove the gas discharge lamp
2.5.4 Replacing the gas discharge lamp , page 93 .
Unscrew fixing screws -1-.

Unhook the control of the control motor out of the bearing
-arrow-.
Take out the control motor -2- taking connected wiring lengths
into consideration and disconnect the connector.
Install
following points:
The knocked-out plug -arrow- must be replaced by a new plug,

see Electronic Catalogue of Original Parts .
After installing
unless the control
authorised motor,
by KODA AUTOcheck the function
A. S. KODA AUTO A. S. is
doescorrect.
not guarantee or accept any liability

3 Lights in the exterior mirror

3.1 Side turn signal lights, page 99
3.2 Door entry lighting, page 100
3.1 Side turn signal lights

Removing
Remove mirror glass Body Work; Rep. gr. 66 .
Press off the catches -arrows A- and push out the cover -1-
-arrow B-.
Unscrew screws -arrows A-.

Press off the catches -arrow B- and remove cover -1-.
Remove socket with
unlessbulb -1-.by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
authorised
3. Lights in the exterior mirror 99

Press off the catches -arrow A- and slightly lower the cover
-1-.
Loosen bottom cover -1- by pushing it out of the catch
-arrow B-.
Disconnect plug.
Press off the catch -arrow- and loosen the side turn signal
lights -1- from the bottom cover -2-.
Installing
Performing functional tests of all functions.
3.2 Door entry lighting

Remove light bulb and housing of the door entry lighting
Remove mirror glass Body Work; Rep. gr. 66 .
Press off the catches -arrows A- and push out the cover -1-
-arrow B-.

Unscrew screws -arrows A-.

Press off the catches -arrow B- and remove cover -1-.
Remove socket with bulb -1-.

Replace defective light bulb (W5W) if necessary.
Press off the catches -arrow A- and slightly lower the cover
-1-.
Loosen bottom cover -1- by pushing it out of the catch
-arrow B-.
Disconnect plug.
Screw out screw -arrow- (0.5 Nm) and remove the lighting
housing -1-.
Installing
3. Lights in the exterior mirror 101

4 Tail lights
4.1 Removing and installing tail light, page 102
4.2 Replacing the light bulbs of the tail light, page 103
4.1 Removing and installing tail light

Assembly tool - T10389-
sentation
Removing
Insert the mounting tools or a hook into the opening of the
cover -1- in order to remove the wheel trim caps (tool kit) -
T10389- , unclip the cover -arrow- from the catches -2- in
sequence and remove.

Take hold of the light -1- and release it carefully from the as
sembly opening in the installed axle by moving it laterally
-arrow-.
Installing
Installation is carried
with respect out in the
to the correctness reversein this
of information order. When
document. installing,
Copyright by KODA AUTO A. S.
Note
Pay attention to the correct fitting and undamaged seals.
Caution
When inserting the tail lights into the assembly opening, ensure
that the connection wiring loom is inserted into the vehicle
cockpit.
Crushed cables between the body and lights causes significant
leakage of rainwater and tail light malfunctions.

4.2 Replacing the light bulbs of the tail light

4.2.1 Tail light - Octavia, page 103
4.2.2 Tail light with LED diodes - Octavia, page 103
4.2.3 Tail light - Octavia Combi, page 104
4.2.4 Tail light with LED diodes - Octavia Combi, page 105
Note
Bulbs for fog light on driver side only.
4.2.1 Tail light - Octavia

Remove tail light
4.1 Removing and installing tail light, page 102 .
Note
The bulb holder is not removed when the side light (-Pos.4-) bulbs
are being replaced. To remove the bulb socket, turn to the left and
remove.

Disconnect plug -1- and removeProtected
bulb holder.
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Summary of components of light bulbs:

1- Light bulb for the reversing light P21W (12V, 21W)
2- Light bulb for the brake light and side light P21W (12 V, 21
W)
3- Light bulb for the turn signal light PY21W (12 V, 21 W)
4- Light bulbs for the side light W5W (12V, 5W)
5- Light bulb for the fog light and side light H21W (12V, 21W)
Note
Check that the bulb holder seals are undamaged.
4.2.2 Tail light with LED diodes - Octavia

Remove tail light
4. Tail lights 103

Note
The LED module is integrated into the lamp and cannot be

changed separately.

Remove bulb carrier.

1- Light bulb for the reversing light P21W (12 V, 21 W)
3- Light bulb for the fog light H21W (12V, 21W)
Module with LED diodes brake light and side light.
Note
Check seal for damage.

When installing the bulb carrier, insert the cable into the mod
ule with LED diodes so that it does not become crushed
between the bulb carrier and the lamp housing.
The module with LED diodes is integrated into the lamp and
cannot be changed separately.
4.2.3 Tail light - Octavia Combi

Remove tail light
To remove, turn to the left and remove the carrier with light
bulb.
1- Light bulb for the brake light and side light P21W (12 V, 21
W)
2- Light bulbs for the side light W5W (12V, 5W)
4- Light bulb for the fog light and side light P21W (12V, 21W)
5- Light bulb for the reversing light P21W (12V, 21W)

4.2.4 Tail light with LED diodes - Octavia

Combi
Remove tail light
Note
The LED module is integrated into the lamp and cannot be

changed separately.
To remove, turn to the left and remove the carrier with light
bulb.
2- Light bulb for the fog light H21W (12V, 21W)
3- Light bulb for the reversing light P21W (12 V, 21 W)
4. Tail lights 105

5 Fog lights, fog lights with the Corner

function
5.1 General description, fault recognition and fault display,
page 106
5.2 Removing and installing fog light, page 107
5.3 Adjusting fog lights, page 108
5.4 Replacing bulb for the fog light, page 108
5.1 General description, fault recognition

and fault display
General description
Two fog light variants are installed (except for Octavia RS) with
functions:
Fog lights
the fog lights with the static cornering light (Corner function)
in two design variants (black or silver frame)
Octavia RS - with functions:
Fog light - both bulbs are lit
Fog lights and cornering light - only the bulb on the outer side
of the headlight lights up to form the cornering light
Fog lights with the Corner function ensure that the surrounding
area of the vehicle is better illuminated when turning, parking etc.
and are controlled by the onboard supply control unit - J519- .
Further information and description of function
sentation
tions
The onboard supply control unit - J 519- features self-diagnosis
to facilitate fault finding.
Use the Vehicle diagnostic tester in the function Targeted fault
finding for checking and fault finding of the fog lights with the
Corner function.

5.2 Removing and installing fog light

Removing (except for Octavia RS and Scout)
Octavia - For example, insert a hook into the opening in the
grid -top arrow- in order to remove the wheel trim cap (tool kit)
and unclip the grid -1- from the catches in sequence and take
out.
Caution
When using the lever tool, mask points where the lever tool is
applied using commercially available adhesive tape.
Loosen the catch -arrow A- with a screwdriver and remove the

headlight -arrow B-.
Disconnect plug.
Remove - Octavia RS
Remove headlight left - front
unless authorised bumper
AUTO A. S. Body
KODA Work; Rep.
AUTO A. S. gr.guarantee or accept any liability
by KODA does not
63 . with respect to the correctness of information in this document. Copyright by KODA AUTO A. S.
Remove headlight right - vehicles with auxiliary heating - front

bumper Body Work; Rep. gr. 63 , without auxiliary heating
- remove front right wheelhouse liner Body Work; Rep. gr.
66 .
Release screws -arrows-.

Disconnect connectors -2- and remove headlamp -1-.
Removing - Octavia Scout
5. Fog lights, fog lights with the Corner function 107

Unclip the cover -1- over the fog light.

Screw out the screws -arrows- (1.5 Nm) and remove the fog
light -2-.
Disconnect plug.
Install
5.3 Adjusting fog lights
Note
Use a headlight beam setting device for setting the headlight

beam. The nominal values and the adjustment procedure can be
found in the Manual Maintenance ; Booklet Octavia III .
5.4 Replacing bulb for the fog light
WARNING
H8 and H16 bulbs are pressurised and can burst when chang
ing the bulb - risk of injury! Wear gloves and safety spectacles
when changing the lamps.
Note
Do not touch the glass when installing the light bulb. Your fingers
will leave traces of grease on the glass which then evaporate
when the bulb is switched on causing it to cloud.

All vehicles except for Octavia RS:
Remove the fog light with the defective light bulb
5.2 Removing and installing fog light, page 107 .
Octavia RS:
Remove headlight left - front bumper Body Work; Rep. gr.
63 .
Right headlight- remove the front right wheelhouse liner

Using a small screwdriver, carefully unlock the catch

-arrow A- and remove the lens -1- -arrow B-.
All vehicles:
Turn socket with lamp in -direction of arrow- and remove.

Replace defective light bulb:
All vehicles except for Octavia RS - H8 light bulb
Octavia RS - with H16 light bulb:
5. Fog lights, fog lights with the Corner function 109

6 Additional brake light

6.1 Removing and installing the high level brake light - Octa
via, page 110
6.2 Removing and installing the high level brake light - Octavia
Combi, page 111
6.3 Removing and installing the high level brake light - Octavia
Combi GreenLine, page 112
6.1 Removing and installing the high level

brake light - Octavia
Removing
Remove the tailgate trim panel Body Work; Rep. gr. 70 .
Release pre-assembly latches -arrows-.
Note unless authorised by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
To facilitate releasing the latches, a welding wire 4 mm must

be used, which is reworked and used as shown.
a = 8 mm
b = 115 mm
c = 120 mm
Remove high level brake light.
Installing
Note
The high level brake light is fitted with LEDs which cannot be re
placed individually.

6.2 Removing and installing the high level

brake light - Octavia Combi
Note
The high level brake light is fitted with LEDs which cannot be re
placed individually.
Removing
Move strips -1- in direction of arrow -A- and take out of the
brake light in direction of arrow -B-.
Prise out the clips -1- with a screwdriver -arrows- and remove.
Note
Surrounding light seal is attached to the body (for a perfect

seal).
Press out the light with force from the edge, and slowly and
carefully remove it from the assembly opening.
Press the brake

Protected light -3-
by copyright. out of
Copying for the assembly
private or commercialopening
purposes, infrom
part or the
in whole, is not permitted
rear -arrows-.
Separate plug connection -1-.
Unlock and remove the connection of the windscreen washer
system -2- by rotating the retaining clip.
Install
If the original light is installed, remove the gasket, clean the
contact surface and glue a new gasket onto the light Elec
tronic Catalogue of Original Parts .
Note
The new gasket must be glued before inserting the metal claps
Pos. -2-.
6. Additional brake light 111

Connect the metal clamps -2- back onto the brake light.
Note
The metal clamps -2- must be fitted in such a way that the pegs
grip on the ends of the clamps below the edge of the glass of the
brake light (if the clamps are correctly fitted, they bounce when
pressed together in direction of arrow -C-).
Position the locking strips -1- on the light in direction of arrow

-A- secure by sliding up to the stop in direction of arrow -B-.
Note
Do not forget to remove the protective film before installing the

new seal.
The assembly opening must be clean and free of all adhesive
residues.
Fit the connector -1- and connection of the windscreen washer

system -2-.
Clip in the assembled brake light -3- back into the assembly
opening in the tailgate -arrows-.
Perform a functional and tightness test on the brake light.
6.3unless Removing
Protected by copyright. andorinstalling
Copying for private thein part
commercial purposes, high level
or in whole, is not permitted
with respectbrake lightof information
to the correctness - Octavia Combi
in this document. GreenLine
Summary of components

1 - Cover caps
2 - Bolts
2.5 0.5 Nm
3 - Spoiler
4 - Connector with foam rubber
cap
5 - Rubber grommet
6 - Brake lights
Removing

Note
Three seal variants are possible.

Self-adhesive foil or a plastic cap -2- is used in some vehicles
instead of the plastic caps -3-.
By seal type:
Variant 1:
Remove caps -3- and pierce them if necessary.
Variant 2:
Pierce foil (the foil is perforated at the point where it is to be
pierced).
Variants 1 and 2:
Insert key -1- (Torx key 20, key length 160-180 mm) through
the guide tube -4-.
Unscrew screws -6- for securing the light -7- in the spoiler
-5-.
Note
The screws remain in the guide tube after they are unscrewed
-4-.
Variant 3 (installed as of CW 41/14):
Remove the plugby-2-

Protected from Copying
copyright. the cap -1-. or commercial purposes, in part or in whole, is not permitted
for private
Insert key (Torx key to20,
with respect the key length
correctness 160-180
of information mm)
in this through
document. theby KODA AUTO A. S.
Copyright
guide tube -3-.
Screw out the fixing screws -5- of the light -6- in the spoiler
-4-.
Note
The screws remain in the guide tube after they are unscrewed
-3-.
All variants:

Tilt out the brake light -2- slightly in the direction of arrow -A-
and remove from the spoiler in direction of arrow -B-, taking
connected wiring lengths into consideration.
Note
After removing the light, the wiring must be cut (if there is no con
nector directly on the light) and the wiring must be reconnected
with the auxiliary measuring set when the original/new light is
installed.
Install
Install in the reverse order of removal. When doing this, note the
following:
Check gasket for light for damage.
If the wiring was cut when the light was removed, reconnect
the wiring using the auxiliary measuring set.
Observe the tightening torque of the screws (see
page 112 ).
Variant 2 - Seal the pierced foil/caps with a piece of standard
impermeable adhesive tape.

7 Registration number lighting

7.1 Removing and installing registration number lighting, page
116
7.2 Replacing bulb for the number plate light, page 116
7.1 Removing and installing registration

number lighting
Removing
Use a suitable screwdriver -arrow- to lever the light -1- out of
the tailgate.
Disconnect the plug -1- from the light -2-.

Installing
The plug -1- is located on the right vehicle side.
7.2 Replacing bulb for the number plate light

Remove number plate light
7.1 Removing and installing registration number lighting,
page 116 .
Replace the defective light bulb -1- (W5W).
After installing, perform functional test.

8 Steering column switch

8.1 Summary of components of steering column switch with
mechanical ignition/starter switch, page 117
8.2 Summary of components of steering column switch with
control unit for electronic steering column lock J764 ,
page 118
8.3 Removing and installing switch unit on the steering col
umn, page 119
8.4 Removing and installing steering column electronics con
trol unit J527 , page 120
8.5 Setting the correct installation position of the restoring ring
with coil spring, page 121
8.6 Contact assignment on the steering column electronics
control unit J527 , page 122
8.7 Self-diagnosis and fault indication, page 122
8.1 Summary of components of steering column switch with mechanical igni

tion/starter switch
1 - Steering column
2 - Shear bolt
2 pieces
3 - Lock cylinder
9.1 Removing and in
stalling lock cylinder,
page 123
4 - Ignition key
5 - Steering column electronics
control unit - J527-
with coil spring for air
bag and restoring ring
with collector ring -
F138-
8.4 Removing and in
stalling steering column
electronics control unit
J527 , page 120
Caution
Risk of damaging the re
storing ring.
The restoring ring and
slip ring must not be ro
tated against each
with respect other of information in this document. Copyright by KODA AUTO A. S.
to the correctness
while they are disman
tled.
6 - Transport security
7 - Screw
1.1 Nm
8. Steering column switch 117

8 - Switch unit on the steering column

with turn signal light switch - E2- and wiper switch for intermittent operation - E22-
Equipment variant with cruise control system: with CCS switch - E45-
Removing and installing 8.3 Removing and installing switch unit on the steering column, page 119
9 - Steering lock housing
Removing and installing 9.2 Removing and installing steering lock housing, page 124
10 - Screw
1.1 Nm
11 - Ignition/starter switch - D-
Removing and installing 9.4 Removing and installing ignition/starter switch, page 126
12 - Magnet for ignition key anti-removal lock - N376-
9.5 Removing and installing ignition key anti-removal lock solenoid N376 , page 126
8.2 Summary of components of steering column switch with control unit for
electronic steering column lock - J764-
1 - Steering column
2 - Shear bolt
2 pieces
3 - Immobilizer reading coil -
D2-
4 - Ignition key
5 - Access and start authorisa
tion button - E408-
10.6 Removing and
installing start/stop but
ton and immobiliser
reader coil for emergen
cy start, page 132
6 - Steering column electronics
control unit - J527-
with coil spring for air
bag and restoring ring
with collector ring -
F138-
8.4 Removing and in
stalling steering column
electronics control unit
J527 , page 120
Caution
Risk of damaging the re
storing ring.
The restoringwithring
respectand
slip ring must not be ro
tated against each other
while they are disman
tled.

7 - Transport security
8 - Screw
1.1 Nm
9 - Switch unit on the steering column
with turn signal light switch - E2- and wiper switch for intermittent operation - E22-
Equipment variant with cruise control system: with CCS switch - E45-
Removing and installing 8.3 Removing and installing switch unit on the steering column, page 119
10 - Screw
1.1 Nm
11 - Lock with control unit for ELV - J764-
Removing and installing 9.3 Removing and installing the ELV J764 , page 125
8.3 Removing and installing switch unit on

the steering column
Removing
Remove steering wheel Body Work; Rep. gr. 69 . Before
the steering wheel is removed from the steering column, the
wheels must be in the straight ahead position.
Removing top and bottom steering column trim Body Work;
Rep. gr. 70 .
Pull out plug fuse -4-, push unlocking down and disconnect
plug connection -3-.
WARNING
Risk of destruction of electronic components by static dis

charge.
Prior to disconnecting theunless
electrical
authorised plug connection the me
by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
chanic must discharge electrostatic,
with respect to thefor example
correctness by briefly
of information in this document. Copyright by KODA AUTO A. S.
touching the door closure strut.
Pull fuse -1- out downwards and press down and disconnect
Disconnect plug connection with wires to the ignition/starter
switch.

Screw out the screw -2- (1.1 Nm) and push the switch unit
-1- out of the bracket on the steering lock.
Installing
Before pushing the switch unit onto the steering column the
correct installation position of the ring rotor must be checked:
The arrows -1- must be facing each other
The coil spring -2- must be visible in the window between the
arrows -4-
Set the correct position if necessary
with coil spring, page 121 .
Make sure that all the retaining lugs and plug connections lock
in place correctly.
8.4 Removing and installing steering col

umn electronics control unit - J527-
The airbag coil spring and restoring ring with slip ring - F138-
are integrated into the steering column electronics unit -
J527- .
If the control unit is replaced, select the replace control unit
function of the respective control unit Vehicle diagnostic test
er.
Removing
Remove steering wheel Body Work; Rep. gr. 69 . Before
the steering wheel is removed from the steering column, the
wheels must be in the straight ahead position.
Rep. gr. 70 .

Pull out plug fuse -4-, push unlocking down and disconnect
WARNING
Risk of destruction of electronic components by static dis

charge.
Prior to disconnecting the electrical plug connection the me
chanic must discharge electrostatic, for example by briefly
touching the door closure strut.
Pull fuse -1- out downwards and press down and disconnect
Unlock and disconnect plug connections -1, 3, 4 and 8-, as

shown in the illustration. Use a screwdriver -6- to loosen the
plug connections -8- carefully out of the catch -7-.
Unscrew screw -5-.
Unlock retention clutches -2- -arrow- and steering column
electronics control unit - J527- from the switch unit on the
steering column.
Installing
Before pushing out the control unit on the switch unit the indi
cator lever must be in the 0 position and the ring rotor -3- must
be inserted in the correct installation position:
The arrows -1- must be facing each other
arrows -4-
Set the correct position if necessary
with coil spring, page 121 .
Make sure that all the retaining lugs and plug connections lock
in place correctly.
8.5 Setting the correct installation position

of the restoring ring with coil spring
It is only carried out if there is a doubt about the correct setting of
the installation position for the restoring ring rotor.
Work procedure
Put the front wheels in straight ahead position.

Slowly turn the ring rotor -3- manually to the left up to the stop.
Turn ring rotor clockwise manually by approximately 3.5 rev
olutions so that:
The arrows -1- are facing each other
arrows -4-
Install steering wheel Body Work; Rep. gr. 69 , if necessary
lock ring rotor with transport security or adhesive tape.
8.6 Contact assignment on the steering col

umn electronics control unit - J527-
You can find the exact contact assignment in Current flow dia
8.7 Self-diagnosis and fault indication

The steering column electronics control unit - J527- is equipped
with self-diagnosis, which facilitates the fault finding.

9 Steering lock with ignition starter

switch and lock cylinder
9.1 Removing and installing lock cylinder, page 123
9.2 Removing and installing steering lock housing,
page 124
9.3 Removing and installing the ELV J764 , page 125
9.4 Removing and installing ignition/starter switch,
page 126
9.5 Removing and installing ignition key anti-removal lock sol
enoid N376 , page 126
9.1 Removing and installing lock cylinder
WARNING
The steering lock must not be moved without the lock cylinder,
otherwise it would block completely. The blocked steering lock
must be replaced
Removing
Note
The steering wheel must not be removed. For installing the fixing
screws of the bottom trim panel for steering column, turn the
steering wheel to the left by 90 and subsequently turn it to the
right.

Rep. gr. 70 .
Place the ignition key in the lock cylinder and turn to position
Ignition on. The recess in the opening -arrow- of the drilled
hole in the ignition lock acts as a cover .
9. Steering lock with ignition starter switch and lock cylinder 123
Lead steel cable -2- (about 1.2 mm in diameter) through the

hole in the ignition key -arrow-.
This unlocks the fuse -3- and the lock cylinder -1- can be pulled
out of the steering lock.
When pulling out the lock cylinder, carefully loosen the immo
biliser reader coil cable.
Separate plug connection for immobiliser -1-.
Note
The reading coil for the vehicle immobiliser is fixed to the lock
cylinder and cannot be replaced separately.
Installing
Place the ignition key in the lock cylinder and turn to position
Ignition on.
Put unlocking wire -2- into the front drilled hole -arrow-.
Push lock cylinder with reader coil into the steering lock hous
ing.
Pull out the wire and lock cylinder until there is an audible click.
Fit the plug connection together
Protected by on theforreading
copyright. Copying coil. purposes, in part or in whole, is not permitted
private or commercial
Note
Pay attention to the correct position of the cable to the reading

coil of the vehicle immobiliser when inserting the lock cylinder.
9.2 Removing and installing steering lock

housing
Removing
Remove steering wheel Body Work; Rep. gr. 69 , bottom
and top steering column trim panel Body Work; Rep. gr.
70 .
Remove the switch unit on the steering column
umn, page 119 .
Disconnect plug connections -1- and -3-.
Drill off screws -arrows- with angle drill with a drill bit of 8.5
mm.
Remove steering lock housing -2- with ignition/starter switch
and lock cylinder.
Remove lock cylinder
9.1 Removing and installing lock cylinder, page 123 and
ignition/starter switch if necessary
9.4 Removing and installing ignition/starter switch,
page 126 .
Installing

Tighten new screws -arrows- until the screw heads have been
broken off.
9.3 Removing and installing the ELV - J764-
Note
If the control unit is replaced, select the replace control unit

function of the respective control unit Vehicle diagnostic tester.
Removing
Remove steering wheel Body Work; Rep. gr. 69 , bottom
and top steering column trim panel Body Work; Rep. gr.
70 .
Remove the switch unit on the steering column
umn, page 119 .
Unlock and disconnect plug connection -1-.
Drill off screws -arrows- with angle drill with a drill bit of 8.5
mm.
Remove control unit -2-.
Installing
Tighten new screws -arrows- until the screw heads have been
broken off.
9.4 Removing and installing ignition/starter

switch
Removing
Note
right.

Rep. gr. 70 .
Separate electrical plug connection -1-.
On the cavities -arrows- in the steering lock housing -4-, unlock
the holding clamps -2- and -3- by inserting watchmaker's
screwdriver.
If this method is not possible for space reasons, make the auxili
ary tool from 2 wire hooks as described below.
At one end of a 1 mm welding wire, bend a loop and cut off

a length -a-.
Dimension -a- = approx. 50 mm
File the end of the wire hook into a point.
Dimension -b- = 5 mm.
Pull the ignition/starter switch out of the steering lock housing
the watchmaker's screwdriver/wire hook must remain inser
ted while the housing is being removed.
Installing
Slide the ignition/starter switch
with respect to the intoof information
correctness the steering lock housing
in this document. Copyright by KODA AUTO A. S.
until there is an audible click.
9.5 Removing and installing ignition key an

ti-removal lock solenoid - N376-
Only on vehicles equipped with automatic gearbox.

Removing
Note
right.

Rep. gr. 70 .
Unlock locking device -arrow A- and pull off magnet for ignition
key anti-removal lock -2- -arrow B-.
To do so unplug the connector simultaneously.
Installing
10 Keyless unlocking of the vehicle/the

steering, keyless start/stop KESSY
system
10.3 Overview of components of the KESSY system,
page 128
10.4 Access and start authorisation control unit J965 ,
page 130
10.5 Aerials of the KESSY system, page 130
10.6 Removing and installing start/stop button and immobiliser
reader coil for emergency start, page 132
10.7 Lock with control unit for ELV J764 , page 133

The KESSY system (Keyless Entry, Start and Exit System a
keyless access and start authorisation system) enables the key
less unlocking and locking of the vehicle, as well as a keyless
engine start and switch-off. It is sufficient to carry the key with you.
The lock with the control unit for ELV - J764- , which is a compo
nent of this system, replaces the mechanical steering lock.
The lock withunless
the
withcontrol unit
respect to the for ELV
correctness - J764- ingenerates
of information this document.the com
mands for switching on/off the S-contact, switching on/off the
ignition (terminal 15) and the engine start/stop. These commands
are transferred as signals to other vehicle components by the on
board supply control unit - J519- .
Overview of components
10.3 Overview of components of the KESSY system,
page 128 .
When handling a fault, it is essential to know the functions and
the operation of the complete KESSY system.
Detailed description of the function and operation of the KESSY
system:

The KESSY system is equipped with self-diagnosis.
For fault recognition and fault finding use the Vehicle diagnostic
tester in the function Targeted fault finding.
10.3 Overview of components of the KESSY system

1 - Aerial
under the rear bumper
10.5.5 Removing and
installing the rear aerial
in the middle,
page 132
2 - Aerial
under the left side trim
panel in luggage com
partment
10.5.4 Removing and
installing rear right aer
ial, page 131
3 - Aerial and sensors
in the outer door handle
on the driver's side
not replaceable individ
ually
in the case of a fault, re
place the complete door
handle Body Work;
Rep. gr. 57
4 - Lock with control unit for
ELV - J764-
10.7 Lock with con
trol unit for ELV J764 ,
page 133
5 - Access and start authorisa
tion control unit - J965-
below the glove com
partment/front passeng
er's side
Removing and installing 10.4 Access and start authorisation control unit J965 , page 130
6 - Start/stop button
10.6 Removing and installing start/stop button and immobiliser reader coil for emergency start, page
132
7 - Immobiliser reader coil for emergency start
10.6Copying
Protected by copyright. Removing
for privateand installing
or commercial start/stop
purposes, in part or button
in whole, isand immobiliser reader coil for emergency start, page
not permitted
132by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
unless authorised
8 - Aerial
under the centre console in the centre
10.5.1 Removing and installing the aerial under the centre console, page 130
9 - Aerial and sensors
in the outer door handle on the front passenger side
not replaceable individually
in the case of a fault, replace the complete outer door handle Body Work; Rep. gr. 57
10 - Aerial
under the right side trim panel in luggage compartment
Removing and installing 10.5.3 Removing and installing rear left aerial, page 131
10. Keyless unlocking of the vehicle/the steering, keyless start/stop KESSY system 129
Other components with which the KESSY system communicates

via the CAN bus
Vehicle voltage control unit - J519-
Data bus diagnostic interface Gateway - J533-
Dash panel insert
Selector lever of the automatic gearbox (vehicles with auto
matic gearbox)
Engine control unit
Control unit for ABS/ESC
10.4 Access and start authorisation control

unit - J965-
On vehicles with left-hand and right hand drive, the control unit is
located in the driver side heating and air conditioning unit.
Removing
Remove dash panel insert
1.3 Removing and installing dash panel insert, page 24 .
Press off the catch peg -arrow A- and push out the diagnostic
interface -1- from the bracket -2- -arrows B-.
Disconnectunless
theauthorised
plug connections
by KODA AUTO-3- byKODA
A. S. unlocking and
AUTO A. S. doestilting
not guarantee or accept any liability
out the clamp.
Installing
If the control unit was replaced, it must be coded with the
Vehicle diagnostic tester. The Vehicle diagnostic tester
must be connected on-line.
Test the complete system for proper operation.
10.5 Aerials of the KESSY system

10.5.1 Removing and installing the aerial under the centre
console, page 130
10.5.2 Removing and installing aerials and sensors in the front
outer door handles, page 131
10.5.3 Removing and installing rear left aerial, page 131
10.5.4 Removing and installing rear right aerial, page 131
10.5.5 Removing and installing the rear aerial in the middle,
page 132
10.5.1 Removing and installing the aerial under

the centre console
The aerial is located in the holder in front of the control lever.
Removing

Remove the centre console Body Work; Rep. gr. 68 .

Using the disassembly tool (e.g. -MP8-602/1- ) lever the aerial
-1- out of the holder -2- and disconnect the plug connection.
Installing
Connect plug connection and press the aerial into the holder.
10.5.2 Removing and installing aerials and

sensors in the front outer door handles
Not replaceable individually.
In the case of a fault, replace the complete outer door handle
10.5.3 Removing and installing rear left aerial

Removing
Remove left side trim panel in luggage compartment Body
Work; Rep. gr. 70 .
Remove the noise insulation from the wheelhouse to reach the
aerial -2-.
Take off aerial -2- from wheelhouse and disconnect plug -1-.
Installing
observe
Protected the Copying
by copyright. following:
for private or commercial purposes, in part or in whole, is not permitted
respect
with If the aerial
to the which
correctness was taken
of information in thisoff is reused,
document. a by
Copyright new double-sided
KODA AUTO A. S.
adhesive tape must be used and the aerial must be fixed again
according to the fig.
10.5.4 Removing and installing rear right aerial

Removing
Remove right side trim panel in luggage compartment Body
Work; Rep. gr. 70 .
Remove the noise insulation from the wheelhouse to reach the

aerial -1-.
Take off aerial -1- from wheelhouse and disconnect plug -2-.
Installing
If the aerial which was taken off is reused, a new double-sided
adhesive tape must be used and the aerial must be fixed again
according to the fig.
10.5.5 Removing and installing the rear aerial

in the middle
Removing
Remove rear bumper Body Work; Rep. gr. 63 .
Press off catch pegs -arrows-, tilt aerial -1- up and push it out.
Disconnect plug.
Installing
10.6 Removing and installing start/stop but
ton and immobiliser reader coil for emer
gency start
Removing
Note
right.
First of all remove the top and then the bottom steering column
trim panel Body Work; Rep. gr. 70 .

Disconnect the plug from the button -1- and from the reader
coil -2-.
Insert two small cross-head screwdrivers (e.g. watch-and-
clock screwdrivers) into the openings -arrows- and press the
sheet pegs.
Grip the bottom part of the button -1- and press it towards the
outside from the bottom trim panel for steering column.
When removing the reader coil -2- first of all remove the button,
then carefully unclip the reader coil using the disassembly
wedge - 3409- .
Installing
If removed, first of all insert the immobiliser reader coil -2- and
lock in place.
Then insert the button -1- into the bottom trim panel and press
until the interlocking lugs lock into place.
Mount plug and install the bottom and top steering column trim
panel.
10.7 Lock with control unit for ELV - J764-

10.7.1 Fault recognition and fault display, page 133
9.3 Removing and installing the ELV J764 , page 125 .
10.7.1 Fault recognition and fault display

The lock with the control unit for ELV - J764- is equipped with self-
diagnosis, which facilitates the fault finding.
11 Parking aid and park steering assis

tant
11.1 Summary of components, page 134
11.2 Remove and install parking aid control unit J446 or park
ing aid and park steering assistant control unit J791 ,
page 136
11.3 Remove and install the front parking aid warning buzzer
H22 , page 136
11.4 Removing and installing the rear parking aid warning
buzzer H15 , page 137
11.5 Removing and installing parking aid senders and park
steering assistant, page 138
11.6 Parking aid sender holder making holes, assignment,
fitting location, gluing procedure, page 139
11.7 Self-diagnosis of the parking aid, page 140
11.1 Summary of components
Note
When handling a fault it is absolutely essential to know the

function of the parking aid.
Description of system and function Owner's manual Octavia
III .
Contact assignment on the control unit as well as connection
of components of parking aid can be found in the Current
flow diagrams, Electrical fault finding and Fitting locations.
Summary of details for the components Electronic Cata
logue of Original Parts .

1 - Front right sender for park

steering assistant
11.5 Removing and
installing parking aid
senders and park steer
ing assistant,
page 138
2 - Front parking aid sender
11.5 Removing and
ing assistant,
page 138
3 - Front left sender for park
steering assistant
11.5 Removing and
ing assistant,
page 138
4 - Parking aid control unit -
J446- or parking aid and park
steering assistant control unit -
J791-
Left-hand drive - on the
relay and fuse holder
Right-hand drive - on
the bearing bracket/
brake pedal right
11.2 Remove and in
stall parking aid control
unit J446 or parking aid
and park steering assis
tant control unit J791 , page 136
5 - The warning buzzer for the front parking aid - H22-
11.3 Remove and install the front parking aid warning buzzer H22 , page 136
6 - Park steering assistant button - E581-
Removing and installing 2.3 Removing and installing switches in centre console, page 153
7 - Button for parking aid - E266-
Removing and installing 2.3 Removing and installing switches in centre console, page 153
8 - Front left sender for park steering assistant
11.5 Removing and installing parking aid senders and park steering assistant, page 138
9 - Rear parking aid sender
Octavia RS has attached
unless the
authorised by senders
KODA AUTO A. inS.the painted
KODA AUTO A.surfaces of the bumper
S. does not guarantee or accept any liability
10 - Rear right sender for park steering assistant
11. Parking aid and park steering assistant 135

11 - Rear parking aid warning buzzer - H15-

11.4 Removing and installing the rear parking aid warning buzzer H15 , page 137
11.2 Remove and install parking aid control

unit - J446- or parking aid and park
steering assistant control unit - J791-
Removing
Remove any protective cladding below the driver side dash
panel.
Left-hand drive- the control unit is found on the relay and fuse
holder:
Unlock the connectors -1- and -2- and remove by tilting out the
clamp.
Press of catch peg -arrow- and pull the control unit -3- out of
the holder.
Right-hand drive - the control unit is at the bearing bracket/brake
pedal right:

Remove expanding rivets -2- and remove unit -1-.
Unlock the connectors -3- and -4- and remove by tilting out the
clamp.
Installing
If the control unit for the parking aid - J446- is replaced:
Code the control unit Vehicle diagnostic tester
11.3 Remove and install the front parking aid

warning buzzer - H22-
Left-hand drive:
The warning buzzer -1- is located to the side of the fuse holder.
Remove knee airbag Body Work; Rep. gr. 68 .

Use a small screwdriver to push the warning buzzer -1- out of

the support -2-.
Disconnect plug.
Right-hand drive:
Warning buzzer -1- is located above the fuse holder.
Remove the glovebox and glovebox frame from the dash pan
el on the front passenger side Body Work; Rep. gr. 70 .
Using a small screwdriver, press out the warning buzzer -1-

from the bearing bracket at the fuse holder -arrow A-.
Disconnect plug.
Install
11.4 Removing and installing the rear parking

aid warning buzzer - H15-
Removing
key.
Undo the top B pillar trim panels and remove the top C and D
pillar trim panels (Combi) Body Work; Rep. gr. 70 .

Loosen headlining Body Work; Rep. gr. 70 and carefully

hang the rear part downward.
Loosen and remove expanding rivets -arrows-.
Disconnect plug -1- and remove warning buzzer -2-.
Installing
11.5 Removing and installing parking aid

senders and park steering assistant
Note
Senders fitted in painted areas the visible area of a new

sender must be painted in the colour of the bumper before
installing.
The parking aid senders must only be painted with a max. 100
m thick layer of paint. Before painting the sender, the rear
part of the sender (terminal connection) must be affixed.
Only the upper part (visible part) of the sender membrane is
painted.
To make it easier to remove the catches -arrow A- you can use
a larger Seeger pliers with bent jaws.

Removing front sender
Remove parking aid front bumper sender Body Work;
Rep. gr. 63 .
Remove parking aid wheelhouse liner front sender Body
Work; Rep. gr. 66 .
Remove the mounting lugs -arrows A-.
Press out the sender -1- on the outer side of the shock ab
sorber inwards.
Remove rear sender
Loosen sender for parking aid bumper bottom part and lever
it downwards slightly Body Work; Rep. gr. 63 .
Remove Octavia RS parking aid rear bumper sender Body
Work; Rep. gr. 63 .
Remove parking aid wheelhouse liner rear sender Body
Work; Rep. gr. 66 .

Remove the mounting lugs -arrows A-.

Press out the sender -1- on the outer side of the shock ab
sorber inwards.
Installing
11.6 Parking aid sender holder making

holes, assignment, fitting location, glu
ing procedure
If the bumper is replaced, new sender holders must be affixed to
the new bumper.
Make holes in the new bumper see Body Work; Rep. gr. 63 .
11.6.1 Assignment of the sender holder, page 139
11.6.2 Fitting position of the sender holders, page 139
11.6.3 Gluing procedure of the sender holders, page 140
11.6.1 Assignment of the sender holder

The sender holders are different in shape and must be assigned
to the relevant
Protected fittingCopying
by copyright. location. Assignment
for private or commercialof the sender
purposes, in part or holder
in whole, isnot permitted
Electronic Catalogue of Original Parts .
11.6.2 Fitting position of the sender holders

The fitting position is determined by the peg on the holder -2- and
the contour of the holder on the bumper -1-.

11.6.3 Gluing procedure of the sender holders
Note
Park steering assistant sender holders have a countersink

collar. Its visible area -1- must be painted the same colour as
the bumper.
The parking aid sender holder does not have a countersink
collar -1-. Therefore a centring pin must be used for precisely
centring the holder in the bumper or gluing the holder with in
serted parking aid sender on which the decoupling ring (black
silicone ring) is placed.
The temperature of the bumper and the sender holder must
be between 15 C and 30 during the glueing procedure.
Clean and thoroughly degrease the marked adhesive area

-1- with isopropyl (technical alcohol).
Evenly apply activator 3MPlastprimer 4298UV, or, if neces
sary, Glass/paint primer K 520 in the marked adhesive area
-1-.
Let the activator dry off for approx. 5 min.
Note
Pay attention to the fitting position

11.6.2 Fitting position of the sender holders, page 139 and
the assignment of the sender holders
11.6.1 Assignment of the sender holder, page 139 .
The application force and the application time determine the
durability of the bonding!
Remove the protective foils from both sides of the adhesive

tape and press the sender holder -2- into the front bumper for
approx. 10 seconds while applying high force.
11.7 Self-diagnosis of the parking aid
The parking aid system is equipped with self-diagnosis. Carry out
self-diagnosis with the Vehicle diagnostic tester in the function

12 Optical parking assistant (rear view

camera)
12.2 Summary of components: Rear view camera system,
page 141
12.3 Removing and installing rear view camera system, page
142

The rear view camera helps the driver during the rear view driving.
This works by showing the driver an image of the traffic situation
behind the vehicle in the radio navigation system monitor.
When the ignition is switched on or the engine is running, the
system will switch on by putting the gear into reverse when the
radio navigation system is switched off.
Note
When handling a fault it is absolutely essential to know the

function and operation of the rear view camera.
Additional information and description of function Owner's
manual Octavia III .
Calibration of the rear view camera is not necessary.
The rear view camera image does not appear on the radio
navigation system until after a full system start. Like a com
puter, the radio navigation system needs a few seconds for
the system to start after being switched on.
The rear view camera consists of the following parts:

the rear view camera - R189-
the control unit with display for radio and navigation - J503-
The rear
Protected view camera
by copyright. Copying forisprivate
equipped withpurposes,
or commercial self-diagnosis.
in part or in whole, is not permitted
Usewith the toVehicle
respect diagnostic
the correctness of informationtester for troubleshooting.
in this document. Copyright by KODA AUTO A. S.
12.2 Summary of components: Rear view camera system
12. Optical parking assistant (rear view camera) 141

1 - Control unit with display for

radio and navigation - J503-
1.6 Removing and in
page 33
2 - Rear view camera system -
R189-
firmly connected with
the grip strip
12.3 Removing and
installing rear view cam
era system, page 142
12.3 Removing and installing rear view cam

era system
Rear view camera - R189- is installed in the grip strip of the lug
gage compartment and firmly connected with the grip strip.
The grip strip must be replaced when replacing the rear view
camera.
Removing
Remove the bottom tailgate trim panel Body Work; Rep. gr.
70 .
Disconnect the connectors on the tailgate and release the ca
bles leading to the rear view camera.

Release the grip with the camera -1- from the catches
-arrows- step by step and remove.
Unlock and disconnect the connector of the rear view camera.
Install
following points:
Press the grip with the camera on the concealed frame step
by step (starting from the left side and left rear tab) into the
assembly opening until the catch pegs click audibly into place.
12. Optical parking assistant (rear view camera) 143

96 Lights, bulbs, switches - interior

1 Interior Lights
1.1 Lights in the roof lining, page 144
1.2 Removing and installing the rear interior light on the left
and right, replace, page 147
1.3 Removing and installing glove box light , page 147
1.4 Removing and installing glove compartment light in the
front centre console, page 148
1.5 Removing and installing door warning lamp, page 148
1.6 Remove and install the footwell lighting for the driver and
front passenger, page 149
1.7 Removing and installing rear footwell lighting, page 150
1.8 Removing and installing luggage compartment light, page
151
1.1 Lights in the roof lining

1.1.1 Removing and installing the front interior light,
page 144
1.1.2 Replace light bulbs for front interior light, page 145
1.1.3 Removing and installing the sliding roof switch,
page 145
1.1.4 Removing and installing the rear interior light in the mid
dle, replace, page 146
1.1.1 Removing and installing the front interior

light
Caution with respect to the correctness of information in this document. Copyright by KODA AUTO A. S.
Note
The shape and control of the lighting can be designed differently

(depending upon equipment), the assembly work is identical.
144 Rep. gr.96 - Lights, bulbs, switches - interior

Loosen the cover -2- out of the catches using the removal
wedge - 3409- and tilt out towards the bottom.
Unscrew screws -arrows- (2 Nm) and tilt out the interior light
-1- and suspend it from the installation frame -3-.
Disconnect plug.
1.1.2 Replace light bulbs for front interior light

Remove front interior light (it is not necessary to disconnect
the plug connection)
144 .
Turn the socket with the light bulb -arrow- and remove.
Carefully remove the light bulb from the socket and replace
(W5W).
1.1.3 Removing and installing the sliding roof

switch
Remove front interior light
144 .
Unlock plug connection and remove from the switch in the
light.
1. Interior Lights 145

Unlock the catches -arrows- and remove the sliding roof switch
from the trim panel.
1.1.4 Removing and installing the rear interior

light in the middle, replace
Removal wedge - 3409-
Loosen the cover with the lens out of the interior light using the
removal wedge-arrows- and remove.
Unlock the stops -arrows- and take the interior light out of the
roof cover.
Disconnect plug.
Pull the defective light bulb (W5W) out of the socket and re
place.

1.2 Removing and installing the rear interior

light on the left and right, replace
Removing
Carefully release the catch -arrow- with a small cross-head
screwdriver, tilt out the interior light and remove.
Disconnect plug.
Push out lens -arrow- and replace bulb (C5W).

Install
Note
For vehicles with panoramic roof and head airbags: Fitting posi
tion of the interior light - the light connector points to the tail end
of the vehicle.
1.3 Removing and
with respect to the installing
correctness of informationglove boxCopyright
in this document. light by KODA AUTO A. S.
Caution
Removing
Place a cross-head screwdriver under the lens and carefully
lever out the light.

Push out the defective light bulb (W5W) and replace it.
If necessary disconnect the plug and remove the light.
Installing
1.4 Removing and installing glove compart

ment light in the front centre console
Removing
Remove storage compartment in the front centre console
Loosen lights -1- and plug connection -2- from the catch pegs
-arrows-.
Install
Note
Ensure the electric installation is fitted correctly to avoid damage.
1.5 Removing and installing door warning

lamp
Caution
Removing
Use a cross-head screwdriver to grasp behind the lens and
carefully lever out lamp.

Tilt out the cover of the light -arrow-.
Carefully pull the light bulb (W5W) out of the socket and mount
a new one.
Installing
1.6 Remove and install the footwell lighting

for the driver and front passenger
Note
When removing and installing the footwell lighting on the front

passenger side, the work procedure is identical to the one on the
driver side.
Place a cross-head screwdriver under the cover on the side of

the cover recess -arrow- and carefully lever out the light.
Disconnect the plug connection.
Replace light bulb

a new one.
1.7 Removing and installing rear footwell

lighting
key.
Place a cross-head screwdriver under the cover -arrow- and
carefully lever out the lamp.
Disconnect the plug connection.
Replace light bulb

a new one.
1.8 Removing and installing luggage com

partment light
key.
Lever out the light at the recess point using the removal wedge
- 3409- or a small screwdriver and remove it from the trim
panel.
Push out the defective light bulb (W5W) and replace it.
If necessary disconnect the plug and remove the light.

2 Interior switches, in the dash panel,

the centre console and the doors
2.1 Removing and installing light switch, page 152
2.2 Removing and installing headlight range control regulator,
page 152
2.3 Removing and installing switches in centre console, page
153
2.4 Removing and installing warning light switch and indicator
light of the front passenger airbag deactivation, page 153
2.5 Removing and installing the switch for the power window
lifter, page 154
2.6 Removing and installing the passenger side glove box light
switch, page 156
2.7 Removing and installing interior monitoring deactivation
switch E 267 and deactivation button for vehicle inclination sender
E 360 , page 157
2.8 Removing and installing the rear seat heating switch, page
157
2.1 Removing and installing light switch

Removing
Turn the turning handle of the light switch to position 0.
Press in the turning handle of the light switch firmly -arrow 1-
and slightly turn it to the right -arrow 2-.
Hold the turning handle in this position and pull the light switch
housing out to the -front arrow 3-.
Disconnect plug connection at switch.
Installing
Mount plug. unless authorised by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
Carefully push the light switch into the opening until the switch
audibly locks into place.

control regulator
Removing
Remove dash panel insert
1.3 Removing and installing dash panel insert, page 24 .

Press together the lateral securing tabs on the adjuster for the
headlamp range control -arrows-.
Pull the adjuster for headlamp range control -A- to the rear out
of the mounting frame in the dash panel casing.
Note
The adjuster for headlamp range control and instrument lighting

rheostat form a single unit.
Installing
Insert the adjuster for headlamp range control into the mount
ing frame and press in place.
Push the securing tabs outwards until they interlock with the
catch pegs.
2.3 Removing and installing switches in

centre console
Removing
Unclip gearshift cover -2- Transmission; Rep. gr. 34 .
Push switch -1- from below -arrow- out of the cover -2-.
Disconnect the plug connections.
Use a small screwdriver to push off the catch pegs

-arrows A-.
Disconnect switch units -1- and -2- from each other
-arrows B-.
Install
following points:
Carefully push the connected
with respect switch
to the correctness unitsin into
of information the assembly
this document. Copyright by KODA AUTO A. S.
opening until the catches click into place audibly.
2.4 Removing and installing warning light

switch and indicator light of the front
passenger airbag deactivation
Removing
2. Interior switches, in the dash panel, the centre console and the doors 153
Remove the display unit for Infotainment, do not disconnect

the cables
1.6 Removing and installing the Infotainment display/con
trol unit, page 33 .
Push switch and indicator light -1- out of the central air outlets
from the rear -arrow-.
Disconnect plug.
Install
2.5 Removing and installing the switch for

the power window lifter
2.5.1 Switch on driver side, page 154
2.5.2 Switch on passenger side and rear, page 155
2.5.3 Removing and installing mirror adjuster switch,
page 156
2.5.1 Switch on driver side
Note
The work sequence of assembly work is identical for all types of

switches for power windows.
Caution

Use the removal wedge - 3409- to lever out the switch -1-
-arrow A-, tilt out -arrow B- and remove.
Disconnect plug.

Slacken the control element out of the catch pegs -arrows- and
remove.
2.5.2 Switch on passenger side and rear

Removing
Remove top cover of the tightening handle -1- -arrow-.
Unclip switch -1- -arrows- and take it out of the cover -2-.
Release and pull off connector -1-.
Installing
Installation is carried out in the reverseunless
order. When
authorised installing,
by KODA AUTO A. S. KODA AUTO A. S. does not guarantee or accept any liability
observe the following: with respect to the correctness of information in this document. Copyright by KODA AUTO A. S.
Note
While pressing the switch in, hold the trim panel -2- in which the
switch is located firmly from above.
Press the switch into the trim panel until the catches click au
dibly.
2.5.3 Removing and installing mirror adjuster

switch
Removing
Remove top cover of the tightening handle -1- -arrow-.
Unclip switch -21- -arrows- and take it out of the cover -1-.
Disconnect plug.
Installing
Note
While pressing the switch in, hold the trim panel -1- in which the
switch is located firmly from above.
Press the switch into the trim panel until the catches click au
dibly.
2.6 Removing
unless authorisedand
by KODAinstalling theAUTO
AUTO A. S. KODA passenger
A. S. does not guarantee or accept any liability
side glove box light switch
Removing
Note
The switch on right-hand drive vehicles is found on a different

side, the work flow for removing and installing is the identical.

Unclip switch -2- from the catch pegs -arrows- and remove.
Installing
Press the switch into the installation location until there is an
audible click.
Check it is functioning correctly (to check, remove the side
cover on the dash panel).

2.7 Removing and installing interior moni

toring deactivation switch -E 267- and
deactivation button for vehicle inclina
tion sender -E 360-
Removing
Loosen the top part of the B-column trim panel at the bottom
-1- on the driver side Body Work; Rep. gr. 70 and tilt slightly.
Push switch -2- out of the trim panel -1-.
Disconnect plug.
Installing
2.8 Removing and installing the rear seat

heating switch
Caution

Lever off the cover -2- using the removal wedge - 3409-
-arrow-.
Unplug
unless authorised connector
by KODA AUTO -1-.
A. S. KODA AUTO A. S. does not guarantee or accept any liability
Push switch -1- from behind -arrow- out of the cover -2-.
3 Components in the luggage compart

ment and tailgate
3.1 Removing and installing the switch for the luggage com
partment lighting, page 158
3.2 Removing and installing the tailgate release switch, page
158
3.1 Removing and installing the switch for

the luggage compartment lighting
The switch for the luggage compartment lighting is located in the
tailgate lock and cannot be replaced individually.
Body Work; Rep. gr. 55
3.2 Removing and installing the tailgate re

lease switch
Body Work; Rep. gr. 55

4 Front camera for diver assistance

systems - R242-
4.1 Removing and installing front camera, page 159
4.2 Removing windscreen heating plate, page 160
sentation
4.1 Removing and installing front camera

Removing
Note
To facilitate removal, turn the mirror as necessary.

Put e.g. the unlocking tool - T30098- or the 0.8 mm feeler
gauge -Pos.
Protected 2- intoCopying
by copyright. the gap, seeorfig.,
for private and unlock
commercial purposes, the
in partcatch pegis not permitted
or in whole,
-arrow
unless A-.
Tilt the right side of the cover -1- downward slightly
-arrow B-.
Take hold of the cover -2- on the right side and pull it moder
ately -arrow- to make a space to insert the unlocking tool -1-
on the left side.
By inserting the unlocking tool into the gap -see fig.- unlock
the catch peg and the left side and remove the cover -2- down
wards.
4. Front camera for diver assistance systems R242 159

Push the cover -1- forward -arrow A- then downward

-arrow B-.
Unclip the front camera -2- from the holding clamps -1-
-arrow A-.
Pull front camera -2- out of the holder -arrow B- and disconnect
the plug connection -3-.
Installing
Calibrate front camera for driver assistance systems - R242-
Chassis; Rep. gr. 44 .
4.2 Removing windscreen heating plate

Removing
Remove front camera for driver assistance systems - R242-
4.1 Removing and installing front camera, page 159 .
Press out catch pegs -arrows A-, tilt out plate -1- -arrow B- and
remove.
Disconnect plug.
Installing

5 Horn
5.1 Removing and installing horn, page 161
5.1 Removing and installing horn
Caution
The tone pitch of the horn is set at the factory. It is prohibited

to change this setting or to adjust the control screw!
If it is noticed that a screw is adjusted, the guarantee is no
longer valid.
Removing
Screw out the fixing screws -1- (16 Nm).
Disconnect plug.
If necessary unscrew nut (12 Nm) and remove holder from
horn.
Installing
5. Horn 161
6 Anti-theft warning system

6.2 Removing and installing the horn H12 , page 162
6.3 Removing and installing interior monitoring sensor G273
and vehicle inclination sender G384 , page 163
switch E267 and deactivation button for vehicle inclination sender
E360 , page 163
6.1 General points

The functions of the anti-theft warning system are integrated in
the onboard supply control unit - J519- .
After replacing the Convenience system central control unit -
J393- or the vehicle voltage control unit - J519- , the anti-theft
warning system must be adapted with the Vehicle diagnostic
tester.
The anti-theft warning system is equipped with self-diagnosis,
which facilitates the troubleshooting.
Note
After triggering the anti-theft warning system, the alarm source

which is stored in the vehicle voltage control unit - J519- is
output.
For determining the alarm source, use the Vehicle diagnos
tic tester in the function Targeted functions measured
value blocks.
Before assembly, the vehicle must be unlocked with the re
lease button of the radio control receiver.
6.2 Removing and installing the horn - H12-
Note
The horn - H12- has an emergency battery which cannot be re

placed as a separate item.
Removing
Switch off the ignition and all electrical components. The ve
hicle must not be locked via the radio control receiver of the
central locking.
66 .

Unscrew nuts -2- and remove alarm horn with holder -1-.
Disconnect plug.
Installing

toring sensor - G273- and vehicle incli
nation sender - G384-
Note
The sensors for interior monitoring - G273- and the vehicle incli
nation sender - G384- form a building unit and cannot be replaced
separately.
Removing
Remove the interior light in the front roof cover
144 .
Release the sensors for interior monitoring -2- out of the bot
tom catches and release from the bracket by slightly tilting out
-arrows B-. Protected by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
Press off the catches -arrows
with respectA- and
to the remove
correctness the vehicle
of information incli Copyright by KODA AUTO A. S.
in this document.
nation sender -1- with sensors for interior monitoring -2- out of
the interior light.
Installing
following points:
After replacing the sender, you must carry out an online ad
justment (parameterisation) with Vehicle diagnostic tester.

toring deactivation switch -E267- and
deactivation button for vehicle inclina
tion sender -E360-
Removing and installing interior monitoring deactivation switch -
E267- and deactivation button for vehicle inclination sender -
E360-
switch E 267 and deactivation button for vehicle inclination sender
E 360 , page 157 .
6. Anti-theft warning system 163

7 Sockets, cigarette lighter

7.1 Removing and installing the 12 V power socket/cigarette
lighter in the centre console, page 164
7.2 Removing and installing the luggage compartment 12 V
power socket, page 164
7.3 Inverter with socket, 12 V / 230 V, page 164
7.1 Removing and installing the 12 V power

socket/cigarette lighter in the centre
console
Workshop Manual Electrical System - General notes Elec
trical System - General notes; Rep. gr. 96 .
7.2 Removing and installing the luggage

compartment 12 V power socket
Removing
Remove left side trim panel in luggage compartment Body
Work; Rep. gr. 70 .
Separate electrical plug connection -1-.
Remove nut -5-.
Pull power socket -2- with socket -3- out of the trim panel -4-.
Installing
7.3 Inverter with socket, 12 V / 230 V

Note
Before working on the power socket it is essential to be familiar

with the description of function, basic safety rules and potential
uses of the power socket Owner's manual Octavia III .
WARNING
There are capacitors in the inverter housing with 12 V /

230 V power socket that could still have a residual voltage
charge.
There is a risk of accidents caused by electric shock.
Inverter housing with 12 V / 230 V power socket must not
be opened in any circumstances.
The plug, cables and 230 V power socket must not be re
paired.
In the case of a fault on the plug, cable or power socket
the entire unit must be replaced.


presentation
Removal wedge - 3409-
Caution
Removing
With the disassembly wedge - 3409- remove the trim panel
-2- from the notches -arrow-.
If present, remove plug from seat heating switch -1-.
Unscrew screws -1- (1 Nm) and loosen the trim panel -2-
-arrow-.
Remove retaining spring -3-.

Press off the catch pegs -arrow A- and push out the socket
outlet -1- from the bracket -2- -arrow B-.
7. Sockets, cigarette lighter 165

If required, separate from the latching mechanism -arrow- and

remove socket outlet bracket -2- from the trim -1-.
Screw out screws -2-, slightly lift inverter with socket -1- and
push it out of the centre console.
Release connector and pull it off.
Installing
Before inserting the trim with the socket outlet into the centre
console, clip the wiring harness into the clip -arrow-.

8 Immobiliser
The model Octavia III features the immobiliser of the fifth gener
ation with on-line connection and Download. The main compo
nent of the fifth generation immobiliser is a central database, in
which all of the theft-relevant data from the participating control
units is stored. It is not possible to adapt the immobiliser control
units without online connection to this database.
A PIN code request of the immobiliser components by fax or
temporary activation of the components is not possible.
All the components of the immobiliser must be initialised on-
line.
All even re-ordered ignition keys are already precoded at
the factory for a specific vehicle and can only be initialised for
this vehicle.
When re-ordering ignition keys, the relevant vehicle identifi
cation number must be provided.
In koda vehicles it is not possible to adapt the components
of other corporate brands.
Immobiliser components:
8.1 Immobiliser control unit J362 , page 167
8.2 Ignition key, page 168
Engine control unit - J623- diesel engines Engine; Rep. gr.
23 , or petrol engines Engine; Rep. gr. 24
8.3 New identity when changing all the components,
page 168
8.4 System test result (online connection), page 169
Further information and description of the individual components
Self-study programme No. 87 ; Immobilisers in koda vehi
cles .
Immobiliser control unit functions - J362- :
Communication between all the immobiliser components
Encryption of data between the control units involved
The immobiliser is equipped with self-diagnosis, which makes
fault finding easier.
For fault finding, use the Vehicle diagnostic tester in the mode
8.1 Immobiliser control unit - J362-

The immobiliser control unit - J362- is integrated in the dash panel
insert. In the event of control unit failure, the complete dash panel
insert must be renewed.
Adapt immobiliser control unit - J362-
Connect Vehicle diagnostic tester.
Select the operating mode Targeted fault-finding in the Ve
Body
Electrical system
8. Immobiliser 167
01 Self-diagnosable systems
Immobiliser
Operation
Adjust dash panel insert
8.2 Ignition key

All even re-ordered ignition keys are already precoded at the
factory for a specific vehicle and can only be adapted to this ve
hicle. When re-ordering ignition keys, the relevant vehicle identi
fication number must be provided and subsequently the new keys
must be adapted to the immobiliser control unit - J362-
Note
Before replacing the lock set or the control units, the function
New identity when changing all the components must be re
trieved.
8.2.1 Adapting and checking the ignition key, page 168
8.2.1 Adapting and checking the ignition key
Noteunless
If new or additional ignition keys are required, they must be adap
ted to the immobiliser control unit.
Adapt the ignition key to the immobiliser control unit - J362- or

check:
Body
Electrical system
Immobiliser
Operation
Adapt and check the ignition key
8.3 New identity when changing all the com

ponents
All necessary steps required for the new installation of all the im
mobiliser components are carried out with this programme.
Body

Electrical system
Immobiliser
Operation
New identity
8.4 System test result (online connection)

The following processes are performed with this test program:
System test for the online connection
Check of user authorisation
Test of the correct cable connection to the koda database
The precondition for this is the online connection (network con
nection) of the tester.
Body
Electrical system
Immobiliser
Operation
Online system test
8. Immobiliser 169
97 Wiring
1 Fuse holder and relay carrier
1.1 Removing and installing relay holder and fuse holder be
hind dash panel, page 170
1.2 Removing and installing relays and fuse holder in the en
gine compartment and E-Box (relays and fuse holder in the
engine compartment), page 171
1.1 Removing and installing relay holder

and fuse holder behind dash panel
Note
You will find the exact assignment of electric cables and the ar
rangement of fuses and relays in Current flow diagrams, Elec
trical fault finding and Fitting locations.
Removing
Left-hand drive:
Loosen dash panel so that the bottom part can be tilted to
wards you slightly Body Work; Rep. gr. 70 .
Unlock catches -2- and -4- -arrows A-.
Push out fuse holder and relays -3- towards you -arrow B- and
hang them downward.
Expose electric cables.
170
Rep. gr.97 - Wiring
Upon removal of the central tube for the dashboard, remove

the relay and fuse holder -3- and then screw out screws -1-
and -2- (3 Nm).
Right-hand drive:
Press the catch -5- on both sides, and remove -arrow C-.
Remove connector -4- -arrow C-.
Unlatch the retainers -1, 2, 3- -arrows A, B, C-.
Push out relay and fuse holder from the mounting bracket
-arrow D-.
Expose electric cables.
Upon removal of the central tube for the dashboard, remove

the relay and fuse holder -3- and then screw out screws -1-
and -2- (3 Nm).
Installing
tery
1.2 Removing and installing relays and fuse

holder in the engine compartment and
E-Box (relays and fuse holder in the en
gine compartment)
Note
You will find the exact assignment of electric cables and the ar
rangement of fuses and relays in Current flow diagrams, Elec
trical fault finding and Fitting locations.
1. Fuse holder and relay carrier 171
Removing
Remove engine control unit and lay it to the side with connec
ted cables:
Diesel engine Engine; Rep. gr. 23
Petrol engine Engine; Rep. gr. 24
Press catches -arrows- and remove lid of E-box -1-.
Use a screwdriver to unlock the catch -2- and push out the
front cover -1- upwards -arrow-.
Loosen wiring loom to the E-Box.
Unlock catches -1-, -2- and -4- -arrow-.

Remove fuse holder and relay -3- and lay them aside.
172 Rep. gr.97 - Wiring

If the fuse holder and relay holder are fully removed, loosen
nuts -1, 2, 4, 5, 6- and screw out screw -3- and loosen electrical
cables -arrow-.
Note
Mark screw connections for re-installation of the electric cables.
Unscrew the nuts -arrows- (9 Nm) and remove control unit

holder -1-.
Loosen E-Box housing -2- from the catch -3- and remove it
upwards from the threaded bolts.
Installing
Tightening torques for connection cables:
M6 tightening torque 6 Nm
M5 tightening torque 4.5 Nm
tery
1. Fuse holder and relay carrier 173

2 Control units
2.1 Vehicle voltage control unit J519 , page 174
2.2 Data bus diagnostic interface Gateway, page 178
2.1 Vehicle voltage control unit - J519-

General description
The vehicle voltage control unit - J519- communicates with other
control units via the data buses CAN bus, its own data buses LIN
bus and data interface GATEWAY.
It controls the convenience functions of the vehicle.
If the vehicle voltage control unit - J519- is replaced, the new
control unit must be coded Vehicle diagnostic tester.
The onboard supply control unit - J519- features self-diagnosis to
facilitate fault finding.
2.1.1 Summary of components - Left-hand drive, page 174
2.1.2 Summary of components - Right-hand drive,
page 176
2.1.3 Removing and installing the vehicle voltage control unit
J519 , page 176
2.1.1 Summary of components -unless

Left-hand
Protected by copyright.drive
Copying for private or commercial purposes, in part or in whole, is not permitted

1 - Parking aid control unit -

J446- or parking aid and park
steering assistant control unit -
J791-
Equipment variants with
parking aid or parking
aid and park steering
assistant
11.2 Remove and in
stall parking aid control
unit J446 or parking aid
and park steering assis
tant control unit J791 ,
page 136
2 - Control unit holder Pos. 1.
3 - Vehicle voltage control unit
holder - J519-
- J519-
2.1.3 Removing and
installing the vehicle
voltage control unit J519
, page 176
5 - Guide for connection of
central electric plug
2. Control units 175

2.1.2 Summary of components - Right-hand drive

holder - J519-
- J519-
2.1.3 Removing and
installing the vehicle
voltage control unit J519
, page 176
3 - Guide for connection of
central electric plug
depending on the equip
ment
2.1.3 Removing and installing the vehicle volt

age control unit - J519-
Removing
Remove any protective cladding below the left dash panel-
where installed.
Remove A pillar trim, bottom left Body Work ; Rep. gr. 70 .
Right-hand drive:
All vehicles:

Disconnect plug connections -1, 2, and 3-.
Note
After unlocking from the guide -6- push the middle plug connec
tion downwards (if installed).
For unplugging the plugs, successively press together the

catches on the plug connections -1- and remove the plugs on
the control unit by swivelling out the clamp
Protected -arrow-.
by copyright. Copying for private or commercial purposes, in part or in whole, is not permitted
To make removal easier, grab the guide -2- (where installed)

with a pair of pliers, press the latches together -arrows A- and
by pulling it downwards -arrow B- slide the guide out of the
control unit -1-.

Unlock catches -arrow-, tilt control unit -4- out of the holder
-5- and remove downwards and towards you.
Installing
Note
If the vehicle voltage control unit - J519- is replaced, the new

control unit must be coded Vehicle diagnostic tester.
2.2 Data bus diagnostic interface Gateway

2.2.1 Summary of components, page 178
2.2.2 Remove and install data bus diagnostic interface Gate
way J533 ., page 179
2.2.1 Summary of components

1 - Connector
Exact contact
assignment Current
flow diagrams, Electri
cal fault finding and Fit
ting locations
2 - Data bus diagnostic inter
face Gateway - J533-
3 - Screw
20 Nm
4 - Crash bar
5 - Dash panel central pipe
2.2.2 Remove and install data bus diagnostic

interface Gateway - J533- .
Note
If the data bus diagnostic interface Gateway - J533- is re

placed, select the replace control unit function of the respec
tive control unit in operating mode Targeted fault finding or
Guided Functions Vehicle diagnostic tester.
The assembly work is identical on right-hand drive vehicles.
Removing
Remove the knee airbag Body Work; Rep. gr. 69 .
Removing the left footwell vent on the driver side Heating,
Air Conditioning; Rep. gr. 80 .

Press safety catch and disconnect plug connection -1-.

Press catches -arrows- and pull control unit downwards -3- out
of the holder-2-.
Installing

3 Vehicle diagnosis, measurement and

information systems, diagnostic con
nection
Following descriptions see Workshop Manual Electrical System
General notes Electrical System General notes; Rep. gr.
27 .
Use and safety instructions
Connect Vehicle diagnostic tester
Fitting location and removal of the diagnostic connection
To remove the diagnostic connection, press the catches
-arrows- together, and push out the diagnosis connection from
the assembly opening.
3. Vehicle diagnosis, measurement and information systems, diagnostic connection 181

4 Wiring loom and plug repair, contact

surface cleaning
All the notes and comments to the following chapters can be
found in the Workshop Manual Electrical System General
General instructions for the repair on the vehicle electrics
General instructions for wiring loom and plug repair
Repair of airbag and belt tensioner cables
Repair of CAN bus lines
Use contact surface cleaning set - VAS 6410-

5 Vehicle diagnosis, testing and infor

mation systems
The following descriptions can be found in the Workshop Manual
Electrical System General notes Electrical System Gen
eral notes; Rep. gr. 97 .
Use and safety instructions
Connect Vehicle diagnostic tester
5. Vehicle diagnosis, testing and information systems 183

6 Wiring loom and plug repair

General instructions for the repair on the vehicle electrics
General instructions for wiring loom and plug repair
Repair of airbag and belt tensioner cables
Repair of CAN bus lines

7 Use contact surface cleaning set -

VAS 6410-
Repairing the cable eyes
Repairing screwed connections
Cleaning the battery pole terminals and battery poles
Preserving
7. Use contact surface cleaning set VAS 6410 185

D4B802B7E7F Electrical System

Uploaded by

Copyright:

Available Formats

D4B802B7E7F Electrical System

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

D4B802B7E7F Electrical System

Uploaded by

Copyright:

Available Formats

Service

Service Department. Technical Information

All rights reserved.

Copyright 2014 KODA AUTO a. s. D4B802B7E7F

27 - Starter, current supply, CCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.4 Infotainment summary of components with navigation . . . . . . . . . . . . . . . . . . . . . . . . . . 32

92 - Windscreen wash/wipe system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

3 Windscreen wiper and washer system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

94 - Lights, bulbs, switches - exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

96 - Lights, bulbs, switches - interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

27 Starter, current supply, CCS

It is recommended to use only original connection material

When working on the battery, wear proper protection and ob

2.1 Basics, battery types, page 2

2.2 Warning instructions and safety precau

2.3 Work sequence when disconnecting

2.3.1 Disconnecting battery

2 Rep. gr.27 - Starter, current supply, CCS

If both terminals are disconnected, only then disconnect pole ter

2.3.2 Work sequence when connecting the

Observe the following additional instructions after working on

Neither grease nor oil the battery terminals.

Vehicles with battery monitoring control unit - J367- (with start/

2.4 Checking battery

2.5 Charging battery

4 Rep. gr.27 - Starter, current supply, CCS

2.6 Removing and installing battery

Observe the battery handling instructions as well as the warn

Pull out heat protection sleeve -4-.

There are certain dangers if the battery is incorrectly mounted

2.7 Removing and installing battery tray

6 Rep. gr.27 - Starter, current supply, CCS

2.8 Battery parameterisation

3.1 Removing and installing starter

Unscrew nut -3- and disconnect positive cable.

Then screw out top fixing screw for starter -arrow-.

8 Rep. gr.27 - Starter, current supply, CCS

The line to terminal B+ must be laid and attached so that it does

Tightening torques for positive cable and earth strap:

4.1 Checking generator

4.2 Removing and installing alternator

Remove the V-ribbed belt engine; Rep. gr. 13 .

10 Rep. gr.27 - Starter, current supply, CCS

1.8 TSI engine Loosen hose clamps -2-, unscrew screws

Vehicles with AC generator secured from the front side screw

Vehicles with AC generator secured from the side screw out

Follow the mounting sequence for the V-ribbed belt Engine;

Vehicles with AC generator secured from the front side for

4.3 Fixing the B+ wire to the AC generator

If the B+ cable is not tightened to the specified tightening tor

12 Rep. gr.27 - Starter, current supply, CCS

Always use a new self-locking nut for attaching the B+ cable

The tightening torque for the self-locking nut of the B+ cable

4.4 Checking the carbon brushes of the AC

4.5 Removing and installing the Bosch volt

Screw out fixing screws -arrows- (2 Nm) of the voltage regu

4.6 Removing and installing the Valeo volt

Unscrew screws -1- and nut -2-.

4.7 Removing and installing the V-ribbed

14 Rep. gr.27 - Starter, current supply, CCS