RCX142
RCX142
MEMO
Introduction
Our sincere thanks for your purchase of this YAMAHA robot controller.
This manual explains how to install and operate the robot controller. Be sure to read this
manual carefully as well as related manuals and comply with their instructions for using
the YAMAHA robot controllers safely and correctly.
2
Refer to the "Programming Manual" for detailed information on robot programs.
1
Safety precautions (Be sure to read before using)
Before using the YAMAHA robot controller, be sure to read this manual and related manu-
als, and follow their instructions to use the robot controller safely and correctly.
Warning and caution items listed in this manual relate to YAMAHA robot controllers.
2 When this robot controller is used in a robot controller system, please take appropriate
safety measures as required by the user’s individual system.
This manual classifies safety caution items and operating points into the following levels,
along with symbols for signal words “WARNING”, “CAUTION” and “NOTE”.
w "WARNING"
WARNING
indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
c "CAUTION"
CAUTION
indicates a potentially hazardous situation which, if not avoided, could result in
minor or moderate injury or damage to the equipment or software.
n Explains
NOTE
key points in the operation in a simple and clear manner.
Note that the items classified into “CAUTION” might result in serious injury depending
on the situation or environmental conditions. So always comply with CAUTION and
WARNING instructions since these are essential to maintain safety.
Keep this manual carefully so that the operator can refer to it when needed. Also make
sure that this manual reaches the end user.
When installing the RCX142 robot controller, please take into account all the instructions
and precautions described in Chapter 3, "Installation".
2
[System design safety points]
w WARNING
• Refer to this manual for details on the operating status of the robot controller and
to related instruction manuals.
Design and configure the system including the robot controller so that it will
always work safely.
• The robot controller has an emergency stop terminal to trigger emergency stop.
Using this terminal, prepare a physical interlock circuit so that the system
2
including the robot controller will work safely.
c CAUTION
• Do not bundle control lines or communication cables together or in close contact with the
robot controller main circuit or power lines. As a general rule, separate them by at least
100mm. Noise in the main circuit or power lines may cause faulty operation or malfunctions.
• Data (programs, point data, etc.) stored in the robot controller is not guaranteed to be
unchanged, so be sure to back it up onto an external storage device.
c CAUTION
• Use the robot controller within the environment specifications listed in this manual.
Using the controller in an environment outside the specification range could lead to electrical
shocks, fires, malfunctions, product damage or lower performance.
• Tighten the screws on the robot controller firmly to make secure connections.
• Never directly touch the conductive sections or electronic components other than the rotary
switches and DIP switches on the outside panel of the robot controller.
• Securely attach each connector cable connector into the receptacles or sockets.
Poor connections will cause faulty operation or malfunctions.
c CAUTION
• Tighten the terminal screws within the specified torque ranges.
A loose terminal screw could lead to short-circuit, faulty operation or malfunctions.
However, if the terminal screw is too tight, short-circuit, faulty operation or malfunctions could
also occur due to screw damage.
• Make sure that no foreign matter such as cutting chips or wire scraps do not enter the robot
controller.
• Always store the cables connected to the robot controller in a conduit or clamp them securely
in place.
If the cables are not stored in a conduit or properly clamped, excessive play or movement or
mistakenly pulling on the cable might damage the connector or cables, and poor cable contact
may lead to faulty operation or malfunctions.
• When disconnecting the cable, detach by gripping the connector itself and not by tugging on
the cable. Loosen the screws on the connector (if fastened with the screws), and then
disconnect the cable.
Detaching by pulling on the cable itself may damage the connector or cables, and poor cable
contact may lead to faulty operation or malfunctions.
3
[Start-up and maintenance safety points]
w WARNING
• Only personnel trained in safety and robot operation may operate it.
• Never allow anyone to enter the robot movement range when the robot controller
is turned on. Serious accidents including fatal injury or death might otherwise
result.
2 • This robot controller is not designed to be explosion-proof. Do not use it in
locations exposed to inflammable gases, gasoline or solvent that could cause
explosion or fire.
• Do not touch any electrical terminal while power is supplied to the robot
controller. This might cause electrical shocks, faulty operation or malfunctions.
• Always shut off all phases of the power supply externally before cleaning or
tightening the terminal screws.
Failure to shut off all phases could lead to electrical shocks, product damage or
malfunctions.
A loose screw could lead to parts dropping out, short circuits or malfunctions.
If the screw is too tight, short circuits or malfunctions could also occur due to
screw damage.
• Never disassemble or modify the robot controller.
This may lead to breakdowns, malfunctions, injury or fire.
• Always shut off all phases of the power supply externally before installing or
removing an option board.
Failure to shut off all phases could lead to breakdowns or malfunctions.
• When using ferrite cores for noise elimination, fit them to the power cable as close
to the robot controller as possible to prevent faulty operation or malfunctions due
to noise.
• When performing maintenance of the robot controller under instructions from the
YAMAHA or YAMAHA sales dealer, turn off the robot controller and wait for at least
30 minutes. Some components in the robot controller may be hot or still retain a
high voltage shortly after operation, so burns or electrical shocks may occur if
those parts are touched.
Revision record
Equivalent
Manual version Issue date Japanese Description
manual version
Ver. 1.00 Dec. 2004 Ver. 2.00 English manual Ver. 1.00 is based on Japanese
manual Ver. 2.00.
4
Before using the robot controller
(Be sure to read the following notes.)
Please be sure to perform the following tasks before using the robot controller.
Failing to perform these tasks will require absolute reset for setting the origin position
each time the power is turned on or may cause abnormal operation (vibration, noise). 2
[1] When connecting the power supply to the robot controller
Reference Always make a secure connection to the ground terminal on the robot controller to
Refer to “4. Connecting to the power”
in Chapter 3, “Installation”. ensure safety and prevent malfunctions due to noise.
Reference
[2] When connecting the battery cable to the robot controller
Absolute reset is always required when The absolute battery is fully charged when the robot controller is shipped to the
the robot controller power is first customer. However, it is left disconnected to prevent battery discharge. After installing
turned on after connecting the robot the controller, always be sure to connect the absolute battery while referring to “9.
cable to the robot controller. Perform
absolute reset while referring to “11.8
Connecting the absolute battery” in Chapter 3 before connecting the robot cables.
Absolute reset” in Chapter 4, An error (relating to absolute settings) is always issued if the robot controller power is
“Operation”. turned on without connecting the absolute batteries, so the origin position cannot be
Absolute reset is also required after the detected. This means the robot connected to this controller cannot be used with absolute
robot cable was disconnected from the
robot controller and then reconnected.
specifications.
5
Overview of the RCX series
The YAMAHA RCX series robot controllers were developed based on years of
YAMAHA experience and proven achievements in robotics and electronics. These
controllers are specifically designed to operate YAMAHA industrial robots efficiently
2 and accurately.
Despite their compact size, the RCX series controllers operate efficiently as multi-axis
controllers with a variety of functions.
1. Multi-task function
Up to 8 tasks* can be run simultaneously in a specified priority. (Low priority tasks
are halted while high priority tasks are run.)
I/O parallel processing and interrupt processing are also available, so that operational
efficiency of the total robot system including peripheral units is greatly improved.
(*: Refer to the Programming Manual for more details on multi-tasking.)
2. Robot language
The RCX series controller comes with a BASIC-like high-level robot language that
conforms to the industrial robot programming language SLIM*1. This robot language
allows easy programming even of complex movements such as multi-task operations
and uses a compiling method*2 for rapid execution of programs.
(*1: Standard Language for Industrial Manipulators)
(*2: This compiling method checks the syntax in a robot language program, converts
it into intermediate codes, and creates an execution file (object file) before actually
performing the program.)
3. Movement command
• Arch motion
Spatial movement during pick-and-place work can be freely set according to the
work environment. This is effective in reducing cycle time.
• Three-dimensional CP control
Allows three-dimensional interpolation control of linear and circular movements.
4. Maintenance
Software servo control provides unit standardization. This allows connection to most
YAMAHA robot models and simplifies maintenance.
5. CE marking*
As a YAMAHA robot series product, the RCX series robot controller is designed to
conform to machinery directives, low-voltage directives and EMC (Electromagnetic
compatibility) directives. In this case, the robot controller is set to operate under SAFE
mode. (* For CE marking compatibility, see the CE marking Supplement Manual.)
This manual explains how to handle and operate the YAMAHA robot controllers correctly
and effectively, as well as I/O interface connections.
Read this manual carefully before installing and using the robot controller. Also refer to
the separate “Programming Manual” and “Robot Owner’s Manual” as needed.
6
Contents
Chapter 1 Safety
1. Safety .........................................................................................1-1
1.1 Safety precautions during robot operation ........................................... 1-2
1.2 Safety precautions during maintenance ............................................... 1-2
1.3 Motor overload precautions ................................................................ 1-2
1.4 Warning labels .................................................................................... 1-3
1.5 Warning marks ................................................................................... 1-3
2. Warranty ...................................................................................1-4
3. Operating environment .............................................................1-5
Chapter 3 Installation
1. Unpacking .................................................................................3-1
1.1 Packing box ........................................................................................ 3-1
1.2 Unpacking .......................................................................................... 3-1
2. Installing the robot controller ....................................................3-2
2.1 Installation .......................................................................................... 3-2
2.2 Installation methods ............................................................................ 3-3
3. Connector names .......................................................................3-5
4. Connecting to the power ...........................................................3-6
4.1 AC200 to 230V single-phase specifications ......................................... 3-6
4.2 Power capacity ................................................................................... 3-6
4.3 Installing an external leakage breaker ................................................. 3-8
4.4 Installing a circuit protector ................................................................ 3-8
4.5 Installing a current control switch ....................................................... 3-8
5. Connecting the robot cables ......................................................3-9
6. Connecting the MPB programming unit ..................................3-10
7. I/O connections ....................................................................... 3-11
8. Connecting a host computer ....................................................3-12
i
9. Connecting the absolute battery ..............................................3-13
10. Replacing the absolute battery ................................................3-16
11. Connecting a regenerative unit ................................................3-17
12. Precautions for cable routing and installation .........................3-18
12.1 Wiring methods ................................................................................ 3-18
12.2 Precautions for installation ................................................................ 3-19
12.3 Methods of preventing malfunctions ................................................. 3-19
13. Checking the robot controller operation .................................3-20
13.1 Cable connection .............................................................................. 3-20
13.2 Emergency stop input signal connection ........................................... 3-21
13.3 Operation check ............................................................................... 3-21
Chapter 4 Operation
1. Operation overview ...................................................................4-1
2. The RCX robot controller ..........................................................4-2
2.1 Part names .......................................................................................... 4-2
2.2 Main functions .................................................................................... 4-2
3. MPB programming unit .............................................................4-3
3.1 Part names .......................................................................................... 4-3
3.2 Main functions .................................................................................... 4-4
3.3 Connection to the robot controller ...................................................... 4-5
4. Turning power on and off ..........................................................4-6
5. Operation keys ..........................................................................4-7
5.1 MPB screen ......................................................................................... 4-7
5.2 Operation key layout .......................................................................... 4-8
5.3 Basic key operation ............................................................................. 4-9
5.4 Function keys .................................................................................... 4-10
5.5 Control keys ...................................................................................... 4-12
5.6 Data keys .......................................................................................... 4-14
5.7 Other keys ........................................................................................ 4-14
6. Emergency stop .......................................................................4-15
6.1 Emergency stop reset ........................................................................ 4-16
7. Mode configuration .................................................................4-18
7.1 Basic operation modes ...................................................................... 4-18
7.2 Other operation modes ..................................................................... 4-19
7.3 Mode hierarchy ................................................................................. 4-20
8. “SERVICE” mode .....................................................................4-24
8.1 Operation device .............................................................................. 4-24
8.2 Prohibition of “AUTO” mode operation ............................................ 4-24
8.3 Hold-to-Run function ........................................................................ 4-24
8.4 Limitations on robot operating speed ................................................ 4-24
9. “AUTO” mode .........................................................................4-25
9.1 Automatic operation ......................................................................... 4-28
9.2 Stopping the program ........................................................................ 4-29
ii
9.3 Resetting the program ....................................................................... 4-30
9.4 Switching task display ....................................................................... 4-32
9.5 Switching the program ...................................................................... 4-33
9.6 Changing the automatic movement speed ......................................... 4-34
9.7 Executing the point trace ................................................................... 4-34
9.7.1 PTP motion mode ........................................................................................... 4-36
9.7.2 ARCH motion mode ....................................................................................... 4-38
9.7.3 Linear interpolation motion mode ................................................................... 4-40
9.8 Direct command execution ............................................................... 4-42
9.9 Break point ....................................................................................... 4-43
9.9.1 Setting break points ........................................................................................ 4-43
9.9.2 Deleting break points ...................................................................................... 4-44
9.10 Executing a step ................................................................................ 4-45
9.11 Skipping a step .................................................................................. 4-45
9.12 Executing the next step ..................................................................... 4-45
10. “PROGRAM” mode .................................................................4-46
10.1 Scrolling a program listing ................................................................ 4-47
10.2 Program editing ................................................................................ 4-48
10.2.1 Cursor movement ........................................................................................... 4-50
10.2.2 Insert/Overwrite mode switching .................................................................... 4-50
10.2.3 Inserting a line ................................................................................................ 4-51
10.2.4 Deleting a character ....................................................................................... 4-51
10.2.5 Deleting a line ................................................................................................ 4-52
10.2.6 User function key display ............................................................................... 4-52
10.2.7 Quitting program editing ................................................................................ 4-53
10.2.8 Specifying the copy/cut lines .......................................................................... 4-53
10.2.9 Copying the selected lines .............................................................................. 4-53
10.2.10 Cutting the selected lines ................................................................................ 4-54
10.2.11 Pasting the data ............................................................................................... 4-54
10.2.12 Backspace ...................................................................................................... 4-54
10.2.13 Line jump ....................................................................................................... 4-55
10.2.14 Searching a character string ............................................................................ 4-56
10.3 Directory .......................................................................................... 4-57
10.3.1 Cursor movement ........................................................................................... 4-58
10.3.2 Registering a new program name .................................................................... 4-58
10.3.3 Directory information display ......................................................................... 4-59
10.3.4 Copying a program ......................................................................................... 4-60
10.3.5 Erasing a program ........................................................................................... 4-61
10.3.6 Renaming a program ...................................................................................... 4-62
10.3.7 Changing the program attribute ...................................................................... 4-63
10.3.8 Displaying object program information ........................................................... 4-63
10.3.9 Creating a sample program automatically ....................................................... 4-64
10.4 Compiling ......................................................................................... 4-66
10.5 Line jump and character string search ............................................... 4-67
10.6 Registering user function keys ........................................................... 4-67
10.7 Resetting an error in the selected program ........................................ 4-70
11. “MANUAL” mode ...................................................................4-71
11.1 Manual movement ............................................................................ 4-74
11.2 Displaying and editing point data ..................................................... 4-77
11.2.1 Point data input and editing ............................................................................ 4-78
11.2.1.1 Restoring point data ........................................................................................ 4-79
11.2.2 Point data input by teaching ........................................................................... 4-80
11.2.3 Point data input by direct teaching .................................................................. 4-84
11.2.4 Point jump display .......................................................................................... 4-84
iii
11.2.5 Copying point data ......................................................................................... 4-85
11.2.6 Erasing point data ........................................................................................... 4-86
11.2.7 Point data trace ............................................................................................... 4-87
11.2.8 Point comment input and editing .................................................................... 4-88
11.2.8.1 Point comment input and editing ..................................................................... 4-89
11.2.8.2 Point data input by teaching ............................................................................ 4-89
11.2.8.3 Jump to a point comment ................................................................................ 4-90
11.2.8.4 Copying a point comment ............................................................................... 4-91
11.2.8.5 Erasing point comments ................................................................................... 4-92
11.2.8.6 Point comment search ..................................................................................... 4-93
11.2.9 Point data error reset ....................................................................................... 4-94
11.3 Displaying, editing and setting pallet definitions ............................... 4-95
11.3.1 Editing pallet definitions ................................................................................. 4-97
11.3.1.1 Point setting in pallet definition ....................................................................... 4-98
11.3.1.1.1 Editing the point in pallet definition ................................................................... 4-99
11.3.1.1.2 Setting the point in pallet definition by teaching ................................................ 4-99
11.3.2 Pallet definition by teaching .......................................................................... 4-100
11.3.3 Copying a pallet definition ............................................................................ 4-102
11.3.4 Deleting a pallet definition ........................................................................... 4-103
11.4 Changing the manual movement speed .......................................... 4-104
11.5 Displaying, editing and setting shift coordinates .............................. 4-105
11.5.1 Editing shift coordinates ................................................................................ 4-108
11.5.1.1 Restoring shift coordinates ............................................................................. 4-109
11.5.2 Editing the shift coordinate range .................................................................. 4-109
11.5.2.1 Restoring a shift coordinate range .................................................................. 4-111
11.5.3 Shift coordinate setting method 1 .................................................................. 4-111
11.5.4 Shift coordinate setting method 2 .................................................................. 4-113
11.6 Displaying, editing and setting hand definitions .............................. 4-115
11.6.1 Editing hand definitions ................................................................................ 4-121
11.6.1.1 Restoring hand definitions ............................................................................. 4-122
11.6.2 Hand definition setting method 1 .................................................................. 4-122
11.7 Changing the display units .............................................................. 4-124
11.8 Absolute reset ................................................................................. 4-125
11.8.1 Checking absolute reset ................................................................................ 4-126
11.8.2 Absolute reset on each axis ........................................................................... 4-127
11.8.3 Absolute reset on all axes ............................................................................. 4-132
11.9 Setting the standard coordinates ...................................................... 4-136
11.9.1 Setting the standard coordinates by 4-point teaching .................................... 4-139
11.9.2 Setting the standard coordinate by 3-point teaching ...................................... 4-141
11.9.3 Setting the standard coordinates by simple teaching ..................................... 4-143
11.10 Executing the user function keys ..................................................... 4-145
12. “SYSTEM” mode ....................................................................4-146
12.1 Parameters ...................................................................................... 4-148
12.1.1 Robot parameters .......................................................................................... 4-150
12.1.2 Axis parameters ............................................................................................ 4-155
12.1.3 Other parameters .......................................................................................... 4-171
12.1.4 Parameters for option boards ......................................................................... 4-177
12.1.4.1 Option DIO setting ........................................................................................ 4-178
12.1.4.2 Serial I/O setting ............................................................................................ 4-179
12.1.4.3 Setting the network parameters ...................................................................... 4-181
12.2 Communication parameters ............................................................ 4-183
12.3 OPTION parameters ....................................................................... 4-189
12.3.1 Setting the area check output ........................................................................ 4-190
12.3.2 Setting the “SERVICE” mode ......................................................................... 4-194
12.3.2.1 Saving the “SERVICE” mode parameters ........................................................ 4-199
12.3.2.2 Help display in “SERVICE” mode ................................................................... 4-199
12.3.3 SIO settings ................................................................................................... 4-200
12.4 Initialization .................................................................................... 4-203
iv
12.4.1 Initializing the parameters ............................................................................. 4-204
12.4.2 Initializing the memory ................................................................................. 4-205
12.4.3 Initializing the communication parameters ................................................... 4-206
12.4.4 Clock setting ................................................................................................. 4-207
12.4.5 System generation ......................................................................................... 4-208
12.5 Self diagnosis .................................................................................. 4-209
12.5.1 Controller check ........................................................................................... 4-209
12.5.2 Error history display ...................................................................................... 4-210
12.5.3 System error details display ........................................................................... 4-211
12.6 Backup processes ............................................................................ 4-212
12.6.1 Internal flash ROM ....................................................................................... 4-212
12.6.1.1 Loading files .................................................................................................. 4-213
12.6.1.2 Saving files .................................................................................................... 4-214
12.6.1.3 Initializing the files ........................................................................................ 4-214
v
2.3 Connector I/O signals ....................................................................... 5-18
2.4 Connector pin numbers .................................................................... 5-19
2.5 Typical input signal connection ........................................................ 5-20
2.6 Typical output signal connection ...................................................... 5-20
2.7 General-purpose I/O signals .............................................................. 5-20
2.7.1 General-purpose input signals ........................................................................ 5-20
2.7.2 General-purpose output signals ...................................................................... 5-20
2.7.3 General-purpose output signal reset (off) ......................................................... 5-21
3. Ratings .....................................................................................5-22
4. Caution items ..........................................................................5-23
Chapter 8 Specifications
1. Controller basic specifications ...................................................8-1
2. Controller basic functions..........................................................8-2
3. Robot controller external view ..................................................8-3
3.1 RXC142 external view ........................................................................ 8-3
4. MPB basic specifications and external view...............................8-4
Chapter 9 Troubleshooting
1. Error Messages ...........................................................................9-1
1.1 Robot controller error messages .......................................................... 9-1
[ 0] Warnings and messages ............................................................................................ 9-3
[ 1] Warnings (error history entry) .................................................................................... 9-5
[ 2] Robot operating area errors ....................................................................................... 9-5
[ 3] Program file operating errors ..................................................................................... 9-8
vi
[ 4] Data entry and edit errors ....................................................................................... 9-10
[ 5] Robot language syntax (compiling) errors ............................................................... 9-11
[ 6] Robot language execution errors ............................................................................ 9-18
[ 9] Memory errors ........................................................................................................ 9-22
[10] System setting or hardware errors ........................................................................... 9-24
[12] I/O and option board errors .................................................................................... 9-26
[13] MPB errors ............................................................................................................. 9-30
[14] RS-232C communication errors .............................................................................. 9-31
[15] Memory card errors ................................................................................................ 9-33
[17] Motor control errors ................................................................................................ 9-35
[21] Major software errors .............................................................................................. 9-42
[22] Major hardware errors ............................................................................................ 9-43
1.2 MPB Error Messages .......................................................................... 9-47
2. Troubleshooting .......................................................................9-49
2.1 When trouble occurs ........................................................................ 9-49
2.2 Acquiring error information .............................................................. 9-50
2.2.1 Acquiring information from the MPB .............................................................. 9-50
2.2.2 Acquiring information from the RS-232C ........................................................ 9-50
2.3 Troubleshooting checkpoints ............................................................. 9-51
vii
MEMO
viii
Chapter 1 Safety
Contents
1. Safety ............................................................................................... 1-1
1.1 Safety precautions during robot operation ............................................... 1-2
1.2 Safety precautions during maintenance ................................................... 1-2
1.3 Motor overload precautions .................................................................... 1-2
1.4 Warning labels ........................................................................................ 1-3
1.5 Warning marks ........................................................................................ 1-3
Please observe all safety rules and cautions to ensure safe and correct use of the YAMAHA robot.
Also, bear in mind that not all safety items can be listed in detail, so that accurate judgment by the
1
operator or service personnel is essential for operating the robot and controller safely.
Safety
Industrial robots are highly programmable, mechanical devices that provide a large degree
of freedom for performing various manipulative tasks. To ensure safe and correct of
YAMAHA industrial robots, carefully read this manual and FOLLOW THE WARNINGS,
CAUTIONS AND INSTRUCTIONS in this chapter. Failure to take necessary safety
measures or mishandling may result in trouble or damage to the robot and injury to
personnel (robot operator or service personnel) including fatal accidents.
Particularly important safety items and operation points are identified in this manual by
the following symbols and signal words.
w "WARNING"
WARNING
indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
c "CAUTION"
CAUTION
indicates a potentially hazardous situation which, if not avoided, could result in
minor or moderate injury or damage to the equipment or software.
n Explains
NOTE
key points in the operation in a simple and clear manner.
To install, operate or adjust the YAMAHA robot or controller safely and correctly, always
follow the instructions explained in this manual by using either of the following methods.
1. Install, operate or adjust the robot or controller while referring to the contents of this
manual.
2. Install, operate or adjust the robot or controller while viewing the contents of the CD-
ROM version manual on your computer screen.
3. Install, operate or adjust the robot or controller while referring to a printout of the
necessary pages from the CD-ROM version manual.
1-1
1. Safety
b. During operation of the robot, be sure to stay out of the work area of the robot
manipulator. Install a safeguard enclosure to keep others away from the work area or
provide a gate interlock using an area sensor that triggers emergency stop when someone
enters the work area.
c. This robot controller is not designed to be explosion-proof. Do not use the controller
and robot in locations exposed to inflammable gases, gasoline or solvent that could
cause explosion or fire.
1-2
1. Safety
Safety
labels.
! CAUTION
ELECTRIC HAZARD
■ This label warns you of possible electrical shock. Do not touch the terminal strip and
connectors to avoid electrical shock.
b. “Read Instruction Manual” label
READ INSTRUCTION
MANUAL
■ This label means that important information you must know is described in the manual.
When in particular connecting a power supply to the robot controller, read this manual
carefully and follow the instructions. Connectors have a particular orientation, so insert
each connector in the correct direction.
■ This mark warns you of possible electrical shock. Do not touch the terminal block and
connectors to avoid electrical shock.
b. “CAUTION” mark
!
■ This mark indicates that important information you must know is described in the
manual.
When in particular connecting a power supply to the robot controller, read this
manual carefully and follow its instructions. Connectors have a particular
orientation, so insert each connector in the correct direction.
1-3
2. Warranty
1 The YAMAHA robot and robot controller you purchased are warranted against malfunctions and defects
as described below.
Safety
Warranty description:
If any failure should arise in the YAMAHA genuine parts constituting the YAMAHA
robot or controller, due to defects in materials or workmanship, YAMAHA will repair or
replace those parts free of charge. (Hereafter called “warranty repair”.)
Warranty period:
This warranty is effective for a period of:
1) one and a half years (18 months) after shipment from Japan, or
2) one year after installation or
3) 2,400 hours of actual operation
whichever comes first.
Exceptions to warranty:
This warranty will not apply in the following cases:
1) Material fatigue arising due to age and wear through operation (natural fading of
painted or plated surfaces, deterioration of parts subject to wear)
2) Minor natural phenomena associated with sensory perceptions which have no bearing
on the quality and function of the robot or controller (signal sounds emitted from
computers, motor rotation sounds etc.).
3) Programs, point data and other internal data that were changed or created by the
user.
1-4
3. Operating environment
Operating temperature
The ambient temperature should be maintained within a range of 0 to 40°C during 1
operation. This is the range in which continuous operation of the robot controller is
guaranteed according to the initial specifications. If the robot controller is installed in a
Safety
narrow space, then heat generated from the controller itself and from peripheral equipment
may drive the temperature above the allowable operating temperature range. This may
result in thermal runaway or malfunctions and may lower component performance along
with shortening their useful service life. So be sure to install the controller in locations
with a vent having a natural air flow. If this proves insufficient, provide forced air-cooling.
Storage temperature
The controller should be stored in a location at an ambient temperature between -10 and
+65°C when not being used. If the robot controller is stored in a location at high
temperatures for extended periods, deterioration of the electronic components may occur
and the memory backup time may decrease.
Operating humidity
The ambient humidity of the robot controller should be 35% to 85% RH (no condensation)
in order to guarantee continuous operation within the initial specifications. Installing the
robot controller inside an air-conditioned or cooled housing is recommended when the
ambient humidity is higher than 85% or when condensation occurs.
Storage humidity
The controller should be stored in a location at an ambient humidity below 95% RH (no
condensation) when not being used. If the robot controller is stored in a location at high
humidity for an extended period of time, rust may form on the electronic components.
Installation location
Always install the robot controller indoors, at a height of less than 1000 meters above sea
level.
This robot controller is neither dust-proof nor water-proof. Do not install it in locations
exposed to oil mist, cutting fluids or cleaning agents.
1-5
MEMO
1-6
Chapter 2 System overview
Contents
1. System overview .............................................................................. 2-1
1.1 Main system configuration ...................................................................... 2-1
1.2 Axis definition for the RCX142 ................................................................ 2-3
The RCX series controllers are designed for use with a SCARA robot or Cartesian robot, mainly for
assembly and pick-and-place applications. Applications also include various inspection instruments,
sealers and spray equipment utilizing linear and circular interpolation functions.
System overview
Example : YK500X
All the axes on the robot controller are used as the main robot axes.
42
OP.1
OP.3 RCX1L.
MODE
NO.
SER. IN JAPAN
ED MADE
ACTUR ENT
MANUF EQUIPM
TION
Y AUTOMA
FACTOR 意
注TION
MPB
CAU
R
MOTO
照
書参
説明
PWR
取扱 TION
RUC
INST
READUAL
MAN
SRV
ERR
XM ROB
I/O
XY BATT
XY
YM
COM
ZR
RGEN
ROB
I/O OP.4
OP.2 P
ZR N
IO
STD.D
ACIN
ZM
TY
SAFE L
~
230V
RM 200--60Hz A
50 500V
.2
MAX
MPB
PLC
PC
YAMAHA robot
2-1
1. System overview
Example: SXYx+T9+T9
Axes 1 and 2 on the robot controller are used as the main robot axes and
axes 3 and 4 are used as the main auxiliary axes.
2 Fig. 2-1-2 System for controlling one robot and auxiliary axes
System overview
42
OP.1
OP.3 RCX1 L.
MODE
NO.
SER. IN JAPAN
ED MADE
ACTUR ENT
MANUF EQUIPM
TION
Y AUTOMA
FACTOR 意
注TION
MPB
CAU
R
MOTO
照
書参
説明
PWR
取扱 TION
RUC
INST
READUAL
MAN
SRV
ERR
XM ROB
I/O
XY BATT
XY
YM
COM
ZR
RGEN
ROB
I/O OP.4
OP.2 P
ZR N
IO
STD.D
ACIN
ZM
TY
SAFE L
~
230V
RM 200--60Hz A
50 500V
.2
MAX
MPB
PLC
PC YAMAHA robot
2-2
1. System overview
System overview
Sub robot auxiliary axis (s?)
Robot controller ................ Indicates the entire robot controller and controls a
maximum of 4 axes.
The letters “RC” are displayed on the MPB.
Main group ........................ Indicates the main robot and main auxiliary axes and has a
maximum of 4 axes.
The letters “MG” are displayed on the MPB.
Main robot ......................... Indicates the robot name specified as a main robot, and
includes all axes of the main robot.
The letters “MR” are displayed on the MPB.
Main robot axes ................. Indicate the axes composing the main robot.
These can be moved with the robot language MOVE
command.
The letters “M?” are displayed on the MPB. (?=1 to 4)
Main auxiliary axes ........... Are the single axes composing the main group.
These cannot be moved with the robot language MOVE
command. Use the DRIVE command to move these axes.
The letters “m?” are displayed on the MPB. (?=1 to 4)
Sub group .......................... Indicates the sub robot and sub auxiliary axes, and has a
maximum of 2 axes.
The letters “SG” are displayed on the MPB.
Sub robot ........................... Indicates the robot name specified as a sub robot, and
includes all axes of the sub robot.
The letters “SR” are displayed on the MPB.
Sub robot axes ................... Indicate the axes composing the sub robot.
These can be moved with the robot language MOVE2
command.
The letters “S?” are displayed on the MPB. (?=1 to 2)
Sub auxiliary axes ............. Are the single axes composing the sub group.
These cannot be moved with the robot language MOVE2
command. Use the DRIVE2 command to move these axes.
The letters “s?” are displayed on the MPB. (?=1 to 2)
Only the main robot axes are usually specified. Auxiliary axes and sub group settings are
for options made at the time of shipment.
2-3
2. Part names and functions
2
MOTOR
PWR MPB
OP.1 OP.3
RCX142
MODEL.
SRV SER. NO.
MANUFACTURED
XM ERR FACTORY AUTOMATION EQUIPMENT MADE IN JAPAN
ROB 注意
I/O CAUTION
System overview
取扱説明書参照
READ INSTRUCTION
MANUAL
XY
YM
COM BATT
ROB XY
I/O
ZR
ZR
OP.2 OP.4
RGEN
ZM
STD.DIO
P
SAFETY N
RM ACIN
200-230V~
50-60Hz
MAX.2500VA
2-4
3. Controller system
The basic block diagram of the RCX robot controller system is shown below.
Fig. 2-3-1
ACIN
2
RGEN
BATT
ZR
XY
N
L
System overview
CN11
CN9
CN8
CN6
CN5 TB1
AC/DC 24V
CN1
CN1
D POWER BOARD ASSY
CN4
CN2
(FG)
TH1
CN3 CN10 CN7 CN2
HEATSINK
MOTOR
5V,±12V
AC/DC
YM CN4
DRIVER2 BOARD ASSY
ZM CN6
RM CN7
CN2 CN5 CN2
CN4
CN1
CN3 CN8
ROB I/O XY
CN11
CN12
ROB I/O ZR DRIVER1 BOARD ASSY
CN7
CN2
SAFETY CN10 CN9 CN5
CN3
CN3
CN1 CN1
OP.BOARD CN2
OP.BOARD CN2
CN3
CN3
CN1 CN1
OP.BOARD CN2
OP.BOARD CN2
2-5
4. Optional devices
2-6
5. Basic sequence from installation to operation
The basic sequence from installation to actual operation is shown below. Refer to this sequence to use the RCX142
safely, correctly and effectively. Before beginning the work, read this owner's manual thoroughly.
Basic procedure Refer to:
Installation, connection and wiring
Chapter 3 1. Unpacking
Install the controller.
2
~
12. Precautions for cable
routing and installation
• Make cable and connector connections.
• Ground the controller.
System overview
• Configure an emergency stop circuit. Chapter 5 Parallel I/O interface
Chapter 6 SAFETY I/O interface
When a serial I/O board is added: See the serial I/O instruction
Set the station number, communication speed, etc. (Setup manuals for detailed
depends on the serial I/O type.) information.
Power ON
Check that the wiring and supply voltage are correct and then turn power on. Chapter 4 4. Turning power on and off
Check that no alarm is issued after turning power on. Chapter 3 13. Checking the robot
controller operation
setting
• Soft limits (movement range) • - Soft limit
* Before determining soft limit positions by jog movement, • Axis tip weight
return-to-origin must first be complete.
* Always set this parameter when using the robot for the
first time. After that, change it as needed.
Perform absolute reset to teach the origin position to the 11.8 Absolute reset
Absolute reset
controller.
* Always perform absolute reset when using the robot for
the first time. After that, reperform it only when the origin
position becomes indefinite (return-to-origin incomplete).
For SCARA robots:
11.9 Setting the standard
Set the reference coordinates (XY coordinate system with the
X-axis rotation center set as the origin). coordinates
Parameter setting Set parameters according to the operation conditions. Chapter 4 12.1 Parameters
Point data editing Create or edit point data according to the robot operation. point data
11.3 Displaying, editing and
setting pallet definitions
Programming Create programs according to the robot operation. 10. "PROGRAM" mode
See the programming
* Programming is unnecessary if not using a program manual for information
such as in operation with I/O commands.
about the programming
language.
Trial operation
Check that the safety devices such as an emergency stop circuit function correctly.
Make a trial run using step operation and make adjustment as needed. Chapter 4 9.2 Stopping the program
~
2-7
MEMO
2-8
Chapter 3 Installation
Contents
1. Unpacking ........................................................................................ 3-1
1.1 Packing box .......................................................................................... 3-1
1.2 Unpacking ............................................................................................ 3-1
1.2 Unpacking
The robot controller is packed with accessories as shown below, according to the order
specifications. Take sufficient care not to apply shocks to the equipment when unpacking.
After unpacking, check the accessories to make sure that nothing is missing. 3
Fig. 3-1-1 Unpacking
Installation
Accessories
MPB
142
OP.1
OP.3 RCX
MODE
L.
NO. IN JAPAN
SER. ED MADE
NT
ACTUR EQUIPME
MANUF TION
Y AUTOMA 意
FACTOR N
注 TIO
CAU
MPB
照
書参
説明 ION
取扱 RUCT
TOR INST
READ AL
MO R MANU
PW
SRV
ERR
ROB
XM I/O
BATT
XY
XY
YM COM
ZR
RGEN
ROB OP.4
I/O P
OP.2
N
ZR
IO
STD.D ACIN
ZM TY L
SAFE
N
30V~
200-2 Hz
50-60 00VA
X.25
RM MA
c The
CAUTION
robot and controller are very
heavy. Take sufficient care not to drop
them during unpacking as this may
damage the equipment or cause
bodily injury.
Accessories
STD. DIO connector 1
MPB terminator 1
L-type bracket set for front and rear panels 1
Standard
SAFETY connector 1
Connector guard for COM connector 1
CD-ROM manual 1
MPB programming unit 1
L-type brackets for side panel 2
Option OPT. DIO connectors 4 Max.
Connector labels 4 Max.
RGU-2 connection cable 1
3-1
2. Installing the robot controller
When installing, choose a proper place for your robot controller, taking into account your system layout,
accessibility for maintenance, etc.
2.1 Installation
Fig. 3-2-1
3
c CAUTION
1. When carrying the robot 50mm or more
Installation
PWR MPB
OP.1 OP.3
RCX142
MODEL.
SRV
damage. XM ERR
SER. NO.
MANUFACTURED
FACTORY AUTOMATION EQUIPMENT MADE IN JAPAN
YM
bumped. Shocks received by the
connectors may damage the PC
COM BATT
boards in the controller. 50mm 50mm
3. Be sure to give the cables used to or more
ROB
I/O
XY
or more
connect the controller enough ZR
ZR
extra length to avoid strain and OP.2 OP.4
RGEN
pulling at the connectors. ZM
STD.DIO
P
4. Keep the controller away from oil SAFETY N
and water. If the controller is to
be used under such adverse RM ACIN
device.
5. Install the controller on a flat, 200-230V~
50-60Hz
MAX.2500VA
level surface. Do not stand the
controller on its side or end, and
do not install in an inverted
position.
Do not install in locations subject
to excessive vibrations.
6. Do not install the controller in When installing the robot controller, follow the precautions below.
locations where the ambient 1. Provide a clearance of at least 50mm from the top or side panel of the controller.
temperature may rise higher than
the rated temperature. 2. Do not block the heat-sink on the side panel.
7. Do not block the fan vents in the
rear panel. If blocked, 3. Do not block the fan on the rear panel of the controller.
temperature inside the controller
will rise leading to malfunctions, 4. Provide a clearance of at least 30mm from the rear panel of the controller.
breakdowns or deterioration of
electric components. Always
provide a clearance of at least
30mm from the rear panel so that
the fan works properly.
3-2
2. Installing the robot controller
Fig. 3-2-2-1
Installation
NKI
YODE
SAN
Fig. 3-2-2-2
c The
CAUTION
L-type brackets have mounting
holes in two different position. Use
the holes that best match the
equipment layout.
42
OP.1
OP.3 RCX1 EL.
MOD
NO.
SER. IN JAPAN
RED MADE
FACTU ENT
MANU EQUIPM
ATION
RY AUTOM
FACTO 意
注 ON
UTI
MPB
CA
R
MOTO
照
書参
説明
PWR
取扱 TION
RUC
D INST
REA UAL
MAN
SRV
ERR
XM ROB
I/O
XY BATT
XY
YM
COM
ZR
RGEN
ROB
I/O OP.4
OP.2 P
ZR N
DIO
STD.
ACIN
ZM
TY
SAFE L
~
230V
RM 200--60Hz A
50 500V
.2
MAX
3-3
2. Installing the robot controller
c CAUTION
• When attaching the L-type
3) Attaching the L-type brackets (supplied as standard accessories) to the rear
3 42
OP.1
OP.3 RCX1 EL.
MOD
NO.
SER. IN JAPAN
RED MADE
FACTU ENT
MANU EQUIPM
ATION
RY AUTOM
FACTO 意
注 ON
UTI
MPB
CA
Installation
R
MOTO
照
書参
説明
PWR
取扱 TION
RUC
D INST
REA UAL
MAN
SRV
ERR
XM ROB
I/O
XY BATT
XY
YM
COM
ZR
RGEN
ROB
I/O OP.4
OP.2 P
ZR N
DIO
STD.
ACIN
ZM
TY
SAFE L
~
230V
RM 200--60Hz A
50 500V
.2
MAX
Fig. 3-2-2-4
42
OP.1
OP.3 RCX1 EL.
MOD
NO.
SER. IN JAPAN
RED MADE
FACTU ENT
MANU EQUIPM
ATION
RY AUTOM
FACTO 意
注 ON
UTI
MPB
CA
R
MOTO
照
書参
説明
PWR
取扱 TION
RUC
D INST
REA UAL
MAN
SRV
ERR
XM ROB
I/O
XY BATT
XY
YM
COM
ZR
RGEN
ROB
I/O OP.4
OP.2 P
ZR N
DIO
STD.
ACIN
ZM
TY
SAFE L
~
230V
RM 200--60Hz A
50 500V
.2
MAX
3-4
3. Connector names
OP.1 OP.3
MOTOR
PWR MPB
OP.1 OP.3
RCX142
MODEL.
ROBI/O XY
ROB
I/O
XY
注意
CAUTION
取扱説明書参照
READ INSTRUCTION
MANUAL
MPB
3
YM
YM
Installation
COM BATT
ROB XY BATT
I/O
ROBI/O ZR COM
ZR
ZR
ZM OP.2 OP.4
RGEN
ZM
STD.DIO
P
SAFETY N
RGEN
RM RM ACIN
SAFETY N ACIN
200-230V~
50-60Hz
MAX.2500VA
OP.2 OP.4
STD.DIO
3-5
4. Connecting to the power
Connect ring-tongue terminals to the power cable and screw them to the terminal block on the front
panel of the controller as shown below.
3-6
4. Connecting to the power
Installation
20 20 20 2000
3-7
4. Connecting to the power
An inrush current, which might be from several to nearly 20 times higher than the rated
current, flows at the instant that the controller is turned on or the robot motors start to
operate. When installing an external circuit protector for the robot controller, select a
circuit protector that provides optimum operating characteristics.
To ensure proper operation, we recommend using a medium to slow response circuit
protector with an inertial delay function. (Refer to the circuit protector manufacturer’s
data sheets for making the selection.)
Example
AC IN
: Surge killer
L : Contactor
AC200V
N
FG
3-8
5. Connecting the robot cables
Connect the robot cables to the mating connectors on the front panel of the controller as shown below.
The “XM”, “YM” and “ROB I/O XY” connectors are for axes 1 and 2, while the “ZM”, “RM” and “ROB I/
O ZR” connectors are for axes 3 and 4.
The robot cable specifications depend on the robot model, so refer to the robot owner’s manual for
details.
3
n Check
NOTE
RCX1
42
Installation
OP.3
MANUF
FACTOR
L.
ACTUR
ED
Y AUTOMA
TION
EQUIPME
NT MADE
IN JAPAN
意
注TION
R
MOTO
照
書参
説明
PWR
取扱 ON
UCTI
INSTR
READ AL
MANU
SRV
ERR
connecting. XM ROB
I/O
XY BATT
XY
YM
COM
ZR
w WARNING
RGEN
ROB
I/O OP.4
OP.2 P
ZR N
ACIN
TY
SAFE
MA
30V~
Hz
50-6000VA
X.25
c Always
CAUTION
securely connect the robot
cables. If they are not securely
connected and fail to make good
contact, the robot may malfunction.
Before turning on the controller,
make sure again that the cables are
securely connected.
Also make sure that the robot is
properly grounded. For details on the
grounding method, refer to the Robot
Owner's Manual.
3-9
6. Connecting the MPB programming unit
As shown in the figure below, the MPB should be connected to the MPB connector on the front panel of
the robot controller. If not connecting the MPB, plug an MPB terminator (supplied as an accessory) into
the MPB connector.
3 OP.3 RCX1
42
OP.1 EL.
MOD
NO.
SER. IN JAPAN
RED MADE
FACTU ENT
MANU EQUIPM
ATION
RY AUTOM
FACTO 意
注 ION
UT
MPB
CA
Installation
R
MOTO
照
書参
説明
PWR
取扱 TION
RUC
D INST
REA UAL
MAN
SRV
ERR
XM ROB
I/O
XY BATT
XY
MPB programming unit
YM
COM
ZR
RGEN
ROB
I/O OP.4
OP.2 P
ZR N
c Use
DIO
STD.
CAUTION ZM
TY
ACIN
SAFE L
3-10
7. I/O connections
The various input/output (I/O) signals from peripheral equipment can be connected to the robot con-
troller. Each I/O is set with a number, and the I/O connector to be used depends on that number.
For more detailed information on inputs and outputs, see Chapter 5, "Parallel I/O interface" or see
Chapter 6, "SAFETY I/O interface".
a. NPN specifications
NPN specifications indicate that a DO (digital output) type NPN open-collector
transistor is used for the I/O port having a transistor and photocoupler, and a 3
corresponding DI (digital input) is also used. NPN specifications therefore make use
of a sink output and a source input (see drawing below).
Installation
DO output (sink type)
Current
NPN
N.COM
Current
b. PNP specifications
PNP specifications indicate that a DO (digital output) type PNP open-collector transistor
is used for the I/O port having a transistor and photocoupler, and a corresponding DI
(digital input) is also used. PNP specifications therefore make use of a source output
and a sink input (see drawing below).
Current
PNP
Current
N.COM
3-11
8. Connecting a host computer
As a standard feature, the robot controller has an RS-232C interface port for data communication with a
host computer. Most computer models having an RS-232C port can be interfaced to the robot controller,
by connecting between the COM connector on the front of the robot controller and the RS-232C port of
the computer.
For more detailed information on the RS-232C interface, see “RS-232C Interface” in Chapter 7.
3 RCX142
MOTOR OP.1 OP.3
PWR MPB
MODEL.
SRV SER. NO.
MANUFACTURED
XM ERR FACTORY AUTOMATION EQUIPMENT MADE IN JAPAN
ROB 注意
I/O CAUTION
取扱説明書参照
READ INSTRUCTION
MANUAL
XY
YM
COM connector
Installation
NOTE I/O
ZR
ZR
OP.2 OP.4
RGEN
ZM
STD.DIO
RM ACIN
200-230V~
50-60Hz
MAX.2500VA
COM connector
Host computer
3-12
9. Connecting the absolute battery
The absolute batteries are fully charged at factory prior to shipping. However, the battery connectors
are left disconnected to prevent discharge.
After installing the controller, always be sure to connect the absolute battery as shown in this manual,
before connecting the robot cable.
Installation
time.
● Standard connection
1) Connect the absolute battery connectors to the "BATT XY/ZR" connectors on the
front right of the controller as shown below.
Fig. 3-9-1
42
OP.1
OP.3 RCX1 L.
MODE
NO.
SER. IN JAPAN
RED MADE
FACTU ENT
MANU EQUIPM
ATION
Y AUTOM
FACTOR 意
注TION
MPB
CAU
R
MOTO
照
書参
説明
PWR
取扱 TION
RUC
D INST
REA UAL
MAN
SRV
ERR
XM ROB
I/O
NKI
YODE
SAN
XY BATT
XY
YM
COM
ZR
RGEN
ROB
I/O OP.4
OP.2 P
ZR N
DIO
STD.
ACIN
ZM
TY
SAFE L
~
230V
RM 200--60Hz A
50 500V
.2
MAX
BATT
3-13
9. Connecting the absolute battery
c When
CAUTION
connecting in parallel use the
● Parallel connection
1) Connect the absolute battery connectors to the "BATT XY/ZR" connectors on the
same batteries.
front right of the controller as shown below.
In this case, connect the two absolute batteries each to the "BATT XY" and/or "BATT
ZR" connectors, even if not using one of the common axes.
Fig. 3-9-2
3
42
OP.1
OP.3 RCX1L.
Installation
MODE
NO.
SER. IN JAPAN
RED MADE
FACTU ENT
MANU EQUIPM
ATION
Y AUTOM
FACTOR 意
注TION
MPB
CAU
R
MOTO
照
書参
説明
PWR
取扱 TION
RUC
D INST
REA UAL
MAN
SRV
ERR
XM ROB
I/O NKI
YODE
SAN
XY BATT
XY
YM
COM
ZR
RGEN
ROB
I/O OP.4
OP.2 P
ZR N
DIO
STD.
ACIN
ZM
TY
SAFE L
~
230V
RM 200--60Hz A
50 500V
.2
MAX
BATT
3-14
9. Connecting the absolute battery
w DoWARNING
not modify the wiring or
For controller equipped with regenerative unit:
1) Pass the absolute battery cords along the groove of the stay so that they come out of
attempt to extend it. This could
cause equipment malfunctions
the front of the controller.
and breakdowns.
Fig. 3-9-3
3
42
OP.3 RCX1
Installation
OP.1 L.
MODE
NO.
SER. IN JAPAN
RED MADE
FACTU ENT
MANU EQUIPM
ATION
Y AUTOM
FACTOR 意
注TION
MPB
CAU
R
MOTO
照
書参
説明
PWR
取扱 TION
RUC
D INST
REA UAL
MAN
SRV
ERR
XM ROB
I/O
XY BATT
XY
YM
COM
ZR
RGEN
ROB
I/O OP.4
OP.2 P
ZR N
DIO
STD.
ACIN
ZM
TY
SAFE L
~
230V
RM 200--60Hz A
50 500V
.2
MAX
n When
NOTE
connecting in parallel connect
2) Connect the absolute battery connectors to the "BATT XY/ZR" connectors on the
front right of the controller as shown below.
the two absolute batteries each to the
"BATT XY" and/or "BATT ZR" Fig. 3-9-4
connectors, even if not using one of the
common axes.
TT
BA
c When
CAUTION
connecting in parallel use the
XY
same batteries.
ZR
EN
RG
* Unplug the absolute battery connectors when you are going to store the controller for
a period of time that is much longer than the backup time.
3-15
10. Replacing the absolute battery
The absolute battery will wear down and must be replaced as needed. For example, replace the bat-
tery when its service life has expired or when problems with backing up data occur even when the
battery charge time was long enough.
Though battery wear depends on the number of charges and the ambient temperature, the battery
should generally be replaced one and a half years after being connected to the controller.
Always charge the new battery after it is installed.
The battery is automatically charged when power is supplied to the controller. Keep power supplied for
a time longer than necessary for charging by referring to the table below.
3 Battery name *1) Battery type Hours until full charge *2) Connection method Backup time *3)
c CAUTION
• This absolute battery replacement B3
3.6V / 2000mAh
48h
Standard connection 680h
Installation
2) Unplug the connector for the absolute battery to be replaced and then remove the
absolute battery by pulling it up and out.
Fig. 3-10-1
3-16
11. Connecting a regenerative unit
When a regenerative unit (RGU-2) is required, connect it between the RGEN connector on the front
panel of the controller and the RGEN connector on the RGU-2 regenerative unit, by using the cable that
comes with the regenerative unit.
Fig. 3-11
n Check
NOTE
the cable and connectors for
bent pins, kinks, and other damage
before connecting.
3
Installation
w WARNING
• The power to the controller
must be off when connecting
the regenerative unit to the
robot controller.
• To prevent electrical shocks,
never touch the RGEN
terminals when power is
supplied to the robot
controller.
c Always
CAUTION
securely connect the cable.
Poor connections or contact failure
may cause malfunctions.
Connector (RGEN)
3-17
12.Precautions for cable routing and installation
2) Keep the communication cable, robot cables and power cable separate from each other.
3 Never bundle them together.
Installation
3) Keep robot cables separate from the power cable. Never bundle them together.
4) Keep robot cables away from other equipment power lines. Never bundle them together.
6) Do not extend the ground wire longer than necessary. The ground wire should be as
short as possible.
I/O cable
MOTOR
PWR MPB
OP.1 OP.3
RCX142
MODEL.
SRV SER. NO.
MANUFACTURED
XM ERR FACTORY AUTOMATION EQUIPMENT MADE IN JAPAN
ROB
I/O CAUTION
READ INSTRUCTION
MANUAL
XY
YM
Communication cable
Robot cable
COM BATT
ROB XY
I/O
ZR
ZR
OP.2 OP.4
RGEN
ZM
STD.DIO
P
SAFETY N
RM ACIN
Power cable
200-230V~
50-60Hz
MAX.2500VA
I/O cable
3-18
12. Precautions for cable routing and installation
Installation
To prevent malfunctions due to noise, take into account the following points.
1) Place a noise filter and ferrite core at a point near the robot controller.
Do not bundle the primary wiring and secondary wiring of the noise filter together.
Bad example
Primary wiring Secondary wiring L
Robot
Noise filter N controller
Ground wire
• Primary wiring and secondary wiring of the noise filter are bundled together.
• Ground wire is bundled with primary wiring of the noise filter.
2) Always attach a surge absorber to the coil of inductive loads (inductive motor, sole-
noid valve, brake solenoid and relay) located near the robot controller.
Example of surge absorber
For inductive motor
Single-phase 3-phase
A
motor motor
B C
DC type AC type
3-19
13.Checking the robot controller operation
This section explains how to check the controller operation using a special connector that comes with
the controller and an applicable robot. Before beginning this check, finish making connections to the
following items.
• Power supply (Do not supply power until you actually begin the operation check.)
• Robot cable
• MPB programming unit
• Absolute battery
3 •
•
Regenerative unit (if needed)
SAFETY connector (supplied)
(Pin 3 is shorted to pin 13, and pin 4 is shorted to pin 14 in the SAFETY connector.)
Installation
42
OP.1
OP.3 RCX1 L.
MODE
NO.
SER. IN JAPAN
ED MADE
ACTUR ENT
MANUF EQUIPM
TION
Y AUTOMA
FACTOR 意
注TION
MPB
CAU
R
MOTO
照
書参
説明
PWR
取扱 TION
RUC
INST
READUAL
MAN
SRV
ERR
XM ROB
I/O
Hot
YM
XY
ROB
COM
XY
ZR
BATT
RGEN
Neutral
Earth
) Power cable
I/O OP.4
OP.2 P
ZR N
IO
STD.D
ACIN
ZM
TY
SAFE L
~
230V
RM 200--60Hz A
50 500V
.2
MAX
MPB
SAFETY connector
(supplied)
YAMAHA robot
3-20
13. Checking the robot controller operation
c External
Fig. 3-13-2
CAUTION
emergency stop and the RCX142
MPB emergency stop button are Emergency stop button
disabled when pin 13 and pin 14 are MPB connector
directly shorted to each other on the
13
SAFETY connector. Make
connections to ensure the system 14
including the robot controller will
always operate safely.
SAFETY SAFETY
MPB
3
connector connector (supplied)
Installation
3 EMG IN1
4 EMG IN2
24V
13 EMG 24V
14 EMG RDY
Motor power
supply
relay coil
GND
GND
Motor power
supply circuit
AC 200V
• The emergency stop button on the MPB is connected to the controller through the
SAFETY connector.
3-21
MEMO
3-22
Chapter 4 Operation
Contents
1. Operation overview ......................................................................... 4-1
Power input AC power input terminal • Used to supply power to the controller.
4
Operation
RS-232C interface • Used for communication through
Robot RS-232C.
Controller
This chapter mainly explains how to operate the MPB programming unit.
n NOTE
• Refer to Chapter 5 for Parallel I/O
interface.
• Refer to Chapter 6 for SAFETY
I/O interface.
• Refer to Chapter 7 for RS-232C
interface.
4-1
2. The RCX robot controller
4 MOTOR
PWR MPB
OP.1 OP.3
RCX142
MODEL.
SRV SER. NO.
MANUFACTURED
XM ERR FACTORY AUTOMATION EQUIPMENT MADE IN JAPAN
Operation
ROB
I/O CAUTION
5 MPB connector
READ INSTRUCTION
MANUAL
XY
YM
COM BATT
ROB XY
I/O
6 COM connector
ZR
ZR
OP.2 OP.4
RGEN
ZM
STD.DIO
P
SAFETY N
RM ACIN
N 1 AC IN terminal
200-230V~
50-60Hz
MAX.2500VA
e “SRV” LED: ......... Lights up when the robot servo is on and turns off when the servo
power is off.
y COM connector: .. Connects to an external device via the RS-232C interface. (D-
SUB 9P female connector)
4-2
3. MPB programming unit
The MPB is connected to the robot controller and allows you to edit or execute robot programs.
4
t UPPER button
Operation
y LOWER button
w Sheet key
r MPB connector
4-3
3. MPB programming unit
w Sheet keys
Use these keys to operate the robot or edit programs.
The sheet keys are grouped into 3 main types: function keys, control keys and data
keys.
r MPB connector
Operation
t UPPER button
This button has the same function as the UPPER sheet key.
y LOWER button
This button has the same function as the LOWER sheet key.
4-4
3. MPB programming unit
MOTOR
PWR
SRV
MPB
OP.1 OP.3
RCX142
MODEL.
SER. NO.
MANUFACTURED
4
XM ERR FACTORY AUTOMATION EQUIPMENT MADE IN JAPAN
ROB
I/O CAUTION
Operation
READ INSTRUCTION
XY
MANUAL
MPB connector
YM
COM BATT
ROB XY
I/O
ZR
ZR
OP.2 OP.4
RGEN
ZM
STD.DIO
P
SAFETY N
RM ACIN
n Emergency
200-230V~
NOTE 50-60Hz
MAX.2500VA
4-5
4. Turning power on and off
This section explains how to turn power on and off, assuming that the external emergency
stop circuit and other necessary units are connected according to the instructions in Chapter
3, "Installation", and also that the robot controller operates correctly.
1) Connect the MPB to the MPB connector on the front panel of the robot controller.
2) Supply the power to the AC IN terminal on the front panel of the robot controller.
The “PWR” LED lights up and the “MANUAL” mode screen appears. (After the
“PWR” LED is lit, it will take a maximum of 3 seconds for the controller to operate
normally.)
c When
CAUTION
connecting the MPB to the 3) When SAFE mode or serial I/O setting is enabled, the controller always starts with the
robot controller, always use the
robot servo turned off. To turn on the robot servo, refer to “14. "UTILITY" mode” in
dedicated cable and connector
this chapter.
4 attached to the MBP. Do not modify
this cable or extend it by using a relay
unit, etc.
4) If return-to-origin is incomplete, eliminate the problem and perform absolute reset.
Operation
n NOTE
• After turning off the robot
controller, wait at least 5 seconds
before turning the power back on
again. If power is turned on again
too quickly after the power was
turned off, the controller might not
start up correctly.
• Do not turn off the robot controller
during program execution. If
turned off, this causes errors in the
internal system data and the
program may not restart correctly
when the power is again turned
on. Always quit or stop the
program before turning off the
robot controller.
4-6
5. Operation keys
Dashed line
Solid line
Return-to-origin incomplete.
Return-to-origin complete.
4
Double-solid line Program is being executed.
Operation
Online command is being executed through RS-232C
“@ “ mark in 2nd column
interface. Changes to a dot ( . ) when the command ends.
...Guideline
4-7
5. Operation keys
Function key
4
Operation
Control key
Data key
4-8
5. Operation keys
Shift 1
#
,
@
Shift 2 Shift 3
Operation
#
UPPER + ,
@
1 “#”
#
,
@
2 “,”
Shift 2: Use a key without holding down the UPPER
#
LOWER + ,
@
3 “@”
4-9
5. Operation keys
F 6
F 1 F 11
(F 1) POINT
F 7
F 2 F 12
(F 2) PALLET
4 F 9
F 4 F 14 (F 4) VEL +
Operation
F 10
F 5 F 15 (F 5) VEL -
F 6
UPPER + F 1 F 11
(F 6) SHIFT
F 7
UPPER + F 2 F 12
(F 7) HAND
F 8
UPPER + F 3 F 13
(F 8) UNITCHG
F 9
UPPER + F 4 F 14
(F 9) VEL ++
F 10
UPPER + F 5 F 15
(F10) VEL --
F8
LOWER + F 3 F 13
(F13) ABS.RST
F 10
LOWER + F 5 F 15
(F15) COORDI
4-10
5. Operation keys
MANUAL 50%[MG][S0H0J]
Current position
M1= 0 *M2= 0 *M3= 0
*M4= 0
↓ ↓ ↓ ↓ ↓
[F1] [F2] [F3] [F4] [F5]
Operation
[F6] [F7] [F8] [F9] [F10] ...UPPER
n From
NOTE
hereon, when the F 6 to F 10 ∨ ABS.RST COORDI
keys are mentioned, it means to press
F6
F11
F10
the F 1 to F 5 keys while holding
F15
↓ ↓ ↓ ↓ ↓
down the UPPER key or UPPER button [F11] [F12] [F13] [F14] [F15] ...LOWER
on the side of the MPB.
Likewise, when the F 11 to F 15
keys are mentioned, it means to press
F10
the F 1 to F 5 keys while holding
F6
Function keys F 1 to F 5 (sheet keys on the MPB) correspond to the function key
F11 F15
down the LOWER key or LOWER button menus on the screen from the left.
on the side of the MPB. Pressing the UPPER key switches to function keys F 6 to F 10 , and pressing the
LOWER key switches to function keys F 11 to F 15 .
4-11
5. Operation keys
4
(2) Extended function keys
Operation
: Switches robots.
ROBOT
↓
: Moves the cursor down.
Moves the pointer (highlighted line number display) down when not editing
on the screen.
←
: Moves the cursor to the left. (Screen scrolls to the right when the cursor reaches
the left end.)
Scrolls the screen to the right when not edited.
→
: Moves the cursor to the right. (Screen scrolls to the left when the cursor reaches
the right end.)
Scrolls the screen to the left when not edited.
4-12
5. Operation keys
Operation
This key is valid only during “AUTO” mode or point trace.
n The
NOTE
to #6- keys are hereafter
#1+ : Moves axis 1 in the + direction or the robot in the +X direction on the XY
#1+
called the Jog keys. coordinates.
The Jog keys are enabled in
“MANUAL” mode.
#1- : Moves axis 1 in the – direction or the robot in the -X direction on the XY
coordinates.
#2+ : Moves axis 2 in the + direction or the robot in the +Y direction on the XY
coordinates.
#2- : Moves axis 2 in the - direction or the robot in the -Y direction on the XY
coordinates.
4-13
5. Operation keys
4 0 to 9 : Enters numbers.
A Z
Operation
: Pressing this key executes a direct command when in “AUTO > DIRECT”
mode.
When the cursor is displayed, pressing this key completes the data input on the
cursor line.
UPPER
: Selects shift 1 for key operation.
4-14
6. Emergency stop
If for some reason you want to stop the robot immediately during operation, press the emergency stop
button on the MPB. Pressing the emergency stop button cuts off power to the robot to stop operation.
A message as shown below appears on the MPB screen. The highlighted display for the mode name is
cancelled during emergency stop.
MANUAL 50%[MG][S0H0J]
———— 12.1:Emg.stop on —————————————————
Current position
*M1= 0 *M2= 0 *M3= 0
*M4= 0
Operation
MPB programming unit
n Besides the emergency stop button on
NOTE
4-15
6. Emergency stop
triggered by an emergency stop 1) Cancel the emergency stop button on the MPB.
input from the SAFETY I/O
interface. To cancel this Emergency stop is released by turning the emergency stop button clockwise.
emergency stop, refer to Chapter
6.
• Origin positions are retained even 2) Press the LOWER key while holding down the UTILITY key.
when emergency stop is triggered,
so the robot can be operated the The screen switches to “UTILITY” mode and the message “Cancel emergency
same as before emergency stop flag?” appears.
just by canceling emergency stop
without absolute reset. Fig. 4-6-2 Emergency stop reset (1)
UTILITY
At this time, pressing the ESC key returns to the previous mode with the motor
power still turned off. To turn on the motor power, continue the following operations.
UTILITY>MOTOR
4-16
6. Emergency stop
5) Press the F 1 (ON) key to turn on the motor power. At the same time, the servomotor
sets to HOLD status.
The mode name “UTILITY” on the system line (1st line) is highlighted.
n IfNOTE
the motor power is turned off due to Fig. 4-6-5 “UTILITY>MOTOR” mode (2)
a serious error, the motor power will
not turn on with “UTILITY >
MOTOR” mode. In this case, the robot UTILITY>MOTOR
controller must be turned back on
again.
Motor power: On
D1=M1: Servo D5=M5: no axis
D2=M2: Servo D6=M6: no axis
D3=M3: Servo
D4=M4: Servo
ON OFF
4
6) Press the ESC key to return to the previous mode.
Operation
4-17
7. Mode configuration
“SERVICE” mode
4-18
7. Mode configuration
n NOTE
• Absolute reset can be performed
(4) “MANUAL” mode
Select this mode to move the robot manually or perform point teaching. Return-to-
only in “MANUAL” mode.
• ”AUTO” mode may be selected
origin and manual movement can be executed only in this mode.
depending on the execution level Operable tasks in this mode differ depending on the parameter settings in “SERVICE”
when the robot controller is turned mode.
on.
(5) “SYSTEM” mode
Select this mode to perform maintenance and adjustment of the YAMAHA robots
such as robot parameter and axis parameter settings.
Operation
(1) “DI/DO Monitor” mode
(2) “UTILITY” mode
These modes can be selected with the control keys.
4-19
7. Mode configuration
Current position
*M1= 0 *M2= 0 *M3= 0
4 *M4= 0
Operation
These are basic modes at the highest hierarchy on the menu. The display position for each
mode name corresponds to each function key of F 1 , F 2 , F 3 and F 4
from the left.
For example, when the F 1 (AUTO) key is pressed, “AUTO” mode is entered.
When “AUTO” mode is entered, the submenu for the “AUTO” mode operation appears
on the guideline.
The submenu also corresponds to the function keys from F 1 to F 15 . (See Fig. 4-
7-4.)
4-20
7. Mode configuration
Functions are switched with the UPPER and LOWER shift keys. The menu display changes
while this shift key is pressed.
Fig. 4-7-3 Shift keys
UPPER LOWER
n NOTE
• When the data is being edited such
Fig. 4-7-4 Function switching
Operation
Second hierarchy > [F6] [F7] [F8] [F9] [F10] ...when UPPER key is
Third hierarchy > pressed.
Fourth hierarchy
∨ STEP SKIP NEXT
Example: PROGRAM > DIR >
ERASE ↓ ↓ ↓
[F11] [F12] [F13] ...when LOWER key is pressed.
The above example shows that the
current mode is entered by
selecting F 2 (PROGRAM) from
>
The “ ” mark at the left end on the guideline shows that the UPPER key is pressed,
the first hierarchy menu, F 3
>
(DIR) from the second hierarchy while the “ ” mark shows that the LOWER key is pressed.
menu and F 7 (ERASE) from
the third hierarchy menu.
Some submenus have other menus for accessing the next hierarchical mode.
For example, pressing the F 8 key in “AUTO” mode while holding down the UPPER
key, switches to “BREAK” mode. Submenus relating to “BREAK” mode then appear.
As explained above, operation can proceed through each hierarchy by selecting the menu
items with the function keys. To return to the previous mode hierarchy, press the ESC
key.
Pressing the MODE key directly returns to the highest modes. The basic 4 modes are
displayed on the guideline, so select the desired basic mode by pressing the corresponding
function key.
Refer to “Mode hierarchy diagram” on the next page for the entire mode hierarchy.
4-21
7. Mode configuration
4 F2 COPY
F3 CUT
F4 PASTE
F5 BS
F6 JUMP
Operation
F7 FIND
F8 FIND+
F9 FIND-
F3 DIR F1 NEW
F5 INFO
F5 COMPILE F6 COPY
F6 JUMP F7 ERASE
F7 FIND F8 RENAME
F8 FIND+ F10 ATTRBT
F9 FIND- F11 OBJECT
F13 ERR.RST F15 EXAMPLE
F3 MANUAL F1 POINT F1 EDIT F1 UNDO
F2 TEACH F3 JUMP
F3 JUMP
F4 VEL+ F1 EDIT
F5 VEL- F2 TEACH
F6 COPY F3 JUMP
F7 ERASE F4 VEL+
F8 UNITCHG F5 VEL-
F9 VEL++ F6 COPY
F10 VEL-- F7 ERASE
F11 TRACE F8 UNITCHG
F12 COMMENT F9 VEL++
F13 ERR.RST F10 VEL--
F14 AXIS← F11 FIND
F15 AXIS→ F12 FIND+
F13 FIND-
F2 PALLET F1 EDIT F1 POINT F1 EDIT
F4 VEL+ F2 METHOD F2 TEACH
F5 VEL- F4 VEL+ F4 VEL+
F5 VEL- F5 VEL-
F6 COPY F8 UNITCHG
F7 ERASE F9 VEL++
F9 VEL++ F10 VEL--
F10 VEL--
F15 PASSWD
F6 SHIFT F1 EDIT
F2 RANGE F4 VEL+
F4 VEL+ F5 VEL-
F5 VEL- F8 UNITCHG
F6 METHOD1 F9 VEL++
F10 VEL--
F4 VEL+
F7 METHOD2 F5 VEL-
F9 VEL++ F8 UNITCHG
F10 VEL-- F9 VEL++
F7 HAND F1 EDIT F10 VEL--
F8 UNITCHG F4 VEL+
F9 VEL++ F5 VEL-
F10 VEL-- F6 METHOD1 F4 VEL+
F8 UNITCHG F5 VEL-
F9 VEL++ F8 UNITCHG
F10 VEL-- F9 VEL++
F13 RST.ABS F1 M1 F10 VEL--
F2 M2 F1 ADJ. +
F3 M3 F2 ADJ. -
F4 M4 F4 VEL+
F11 ALL F5 VEL-
F15 COORDI F1 4POINTS F9 VEL++
F2 3POINTS F10 VEL--
F5 SIMPLE
4-22
7. Mode configuration
F4 INIT F1 PARAM
F2 MEMORY
F1 PROGRAM
F2 POINT
4
F3 SHIFT
F4 HAND
Operation
F5 ALL
F3 CMU F6 PALETTE
F7 COMMENT
F4 CLOCK F1 DATE
F2 TIME
F6 GENERAT F1 ROBOT
F10 PASSWRD F2 AXIS
F5 DIAGNOS F1 CHECK F4 CLEAR
F2 HISTORY F5 HELP
F6 AUX
F9 BACKUP F4 RAMCARD F7 DUAL
F15 DRV.UP F5 FROM F15 LAYOUT
UTILITY 1 F1 MOTOR
F2 SEQUENC
F3 ARMTYPE
F5 RST.DO
F9 DSW.HLP
UTILITY 2 F1 EXECUTE
F2 ACCESS
F5 RST.DO
F9 DSW.HLP
DISPLAY
4-23
8. “SERVICE” mode
c CAUTION
• Use “SYSTEM” mode to select
8.1 Operation device
the functions in “SERVICE” If operation from a device other than the MPB is permitted, the operator using the MPB
mode. (Refer to “12.3.2 Setting
may be exposed to hazardous situations. For example:
the “SERVICE” mode” in this
chapter.) 1. When a dedicated DI start signal is turned ON without the MPB operator knowing
• Basically, MPB operation is only about it.
allowed in “SERVICE” mode, so
application software (VIP/WIN,
2. When an external device runs a robot operation command through the RS232C interface
etc.) that executes on-line without the MPB operator knowing about it.
commands through the RS232C
4 interface cannot be used, except
for cases where other operating
To prevent this kind of accident in “SERVICE” mode, only the MPB can be used to
operate the robot and other operation devices are disabled. However, you may add other
devices are enabled by on-line operation devices provided you take responsibility for your own safety.
commands made via the RS232C.
Operation
4-24
9. “AUTO” mode
The initial “AUTO” mode screens are shown in Fig. 4-9-1 and Fig. 4-9-2.
Fig. 4-9-1 “AUTO” mode (one-robot setting)
Operation
Fig. 4-9-2 “AUTO” mode (two-robot setting)
q Mode hierarchy
Shows the current mode hierarchy. When the highest mode (“AUTO” in this case) is
not highlighted, it means the servomotor power is off. When highlighted, it means the
servomotor power is on.
w Task display
Shows the task number for the program listing being displayed.
e Automatic movement speed
Robot movement speed is displayed during automatic operation.
When two robots are specified, two speeds are displayed for “ main group / sub group ”,
with the currently selected group highlighted.
r Program name
Shows the program name currently selected.
t Message line
If an error occurs, the error message appears here. A dashed line means return-to-
origin is incomplete. A solid line means return-to-origin return is complete. A double-
solid line means automatic operation is in progress.
4-25
9. “AUTO” mode
4 return-to-origin must be
completed before starting "AUTO"
mode. If return-to-origin is not
do next also appears here in some operation steps.
complete, the message "Origin Upon entering “AUTO” mode, the specified program is compiled and an object file is
Operation
4-26
9. “AUTO” mode
Valid keys and submenu descriptions in “AUTO” mode are shown below.
Page key
Switches to other screens.
( / )
F6
VEL-
POINT
steps.(100→50→20→5→1 %)
Operation
F8 BREAK Sets a break point.
ROBOT
( LOWER Switches the selected robot group.
+ MODE )
4-27
9. “AUTO” mode
w WARNING
• Upon pressing the key,
Fig. 4-9-3 Automatic operation in progress
Operation
START
the robot starts to move. To AUTO [T1] 100% <TEST1 >
avoid danger, do not enter
the robot movement range. 0.2:Running
• When changing the
automatic movement speed
during automatic operation,
check safety for surrounding
areas.
n When
NOTE
automatic movement speed was
The following keys are enabled during automatic operation.
F10 VEL- - Decreases automatic movement speed for the selected robot group in 5% decrements.
ROBOT
( LOWER Switches the selected robot group.
+ MODE )
4-28
9. “AUTO” mode
c DoCAUTION
not turn off the robot controller RESET TASK DIR VEL+ VEL- 4
during program execution. If turned
off, an error may occur in the internal
Operation
system data and the program might
not restart normally when the power 2) Press the ESC key to display the program listing.
is again turned on. Always be sure to
terminate or stop the program before The pointer indicates the next command line number to be executed in the program.
turning the power off.
4-29
9. “AUTO” mode
1 *ST:
2 MOVE P, P0
3 MOVE P, P1
4 MOVE P, P2
5 GOTO *ST
Reset program OK? YES NO
4-30
9. “AUTO” mode
1 *ST:
2
3
MOVE P, P0
MOVE P, P1 4
4 MOVE P, P2
5 GOTO *ST
Operation
Change to _SELECT OK? YES NO
2) When the F 5 (NO) key is pressed in Step 1), the following message then
appears on the guideline.
Press the F 4 (YES) key to reset the current program, or press the F 5 (NO)
key to cancel the reset.
n The
NOTE
output is also reset when the
AUTO [T1] 50% <TEST1 >
4-31
9. “AUTO” mode
5 MOVE P,P0
Operation
6 *L1:
7 MOVE P,P1
8 MOVE P,P2
9 GOTO *L1
RESET TASK DIR VEL+ VEL-
11 WAIT DI2(0)=1
12 DO2(1)=1
13 DELAY 1000
14 DO2(1)=0
15 WAIT DI2(0)=0
RESET TASK DIR VEL+ VEL-
4-32
9. “AUTO” mode
Operation
No. NAME LINE BYTE RW/RO
1 TEST1 13 125 RW
2 TEST2 50 608 RW
3 PARTS100 38 411 RW
4 TEST3 7 78 RW
4-33
9. “AUTO” mode
n When
NOTE
two robots are specified, two
9.6 Changing the automatic movement speed
speeds are displayed for “ main group / Automatic movement speed for the selected robot group can be set within the range of 1
sub group ”. The speed shown
to 100%.
highlighted can be set. To switch the
robot group, use the ROBOT key [Procedure]
( LOWER + MODE ).
1) Press the F 4 (VEL+) or F 5 (VEL-) key in “AUTO” mode to change the
speed in steps.
n Automatic
NOTE
movement speeds once set Each time the F 4 (VEL+) or F 5 (VEL-) key is pressed, the speed changes
here are stored in the internal memory
even when the power is turned off.
in steps of 1← →5← →20← →50← →100%.
If the speed is set with the program The maximum motor speed is set at 100%.
command statement (SPEED
statement), the actual robot operating
speed will be the product of that speed 2) Press the F 9 (VEL++) or F 10 (VEL--) key to change the speed gradually.
4 and the automatic movement speed.
For example, if the automatic
movement speed is 80% and the speed
Each time the F 9 (VEL++) or F 10 (VEL--) key is pressed, the speed
specified by the SPEED statement is changes in units of 1%.
Holding down the key changes the speed continuously.
Operation
* The “[RIGHTY]” message on the first line appears only when a SCARA robot is
selected.
* The “[LEFTY]” message on the sixth line appears only when a SCARA robot is
selected, and a hand system flag is set for the point data.
4-34
9. “AUTO” mode
Valid keys and submenu descriptions in “AUTO > POINT” mode are shown below.
Valid keys Menu Function
Cursor key
Switches the point number and scrolls the screen.
(↑/↓)
Page key
Switches to other screens.
( / )
PTP/ARCH/
F1 Switches the trace movement mode.
LINEAR
F2 A.POS Specifies the arch position during ARCH motion mode.
F3 JUMP Displays the specified point data.
F5 VEL-
Decreases automatic movement speed for the selected robot group in
steps.(100→50→20→5→1 %)
4
F6 A.AXIS+ Moves the arch axis to the right during ARCH motion mode.
Operation
F7 A.AXIS- Moves the arch axis to the left during ARCH motion mode.
F8 UNITCHG Switches the units for indicating the current position to “mm/pulse”.
Increases automatic movement speed for the selected robot group in 1%
F9 VEL++
increments.
F11 MODIFY Switches to the point data editing screen in “MANUAL” mode.
F14 AXIS← Moves the cursor to the left to select another axis.
F15 AXIS→ Moves the cursor to the right to select another axis.
ROBOT
( LOWER Switches the selected robot group.
+ MODE )
F 11 (MODIFY) key
Pressing the F 11 (MODIFY) key switches to the point data edit screen and allows you
to correct the point data while checking the point trace position.
To return to the trace mode, press the F 11 (TRACE) key again.
4-35
9. “AUTO” mode
Fig. 4-9-13 Point trace screen in PTP motion mode (with no auxiliary axis)
4 P5
COMNT :
= -63432 19735 6243
[LEFTY]
22642
[POS] 0 0 0 0
Operation
2) Use the cursor (↑/↓) keys to select the point number to be checked.
Fig. 4-9-14 Point trace screen in PTP motion mode (with no auxiliary axis)
w Upon
WARNING
pressing the key, the
3) Press the START key, and the robot moves by PTP motion to the specified point position.
The trace speed is one tenth of the automatic movement speed. If the SCARA robot is
START
robot starts to move. To avoid selected and the hand system flag is set for the point data, then this hand system will
danger, do not enter the robot
movement range. have priority. To stop the trace, press the STOP key.
4-36
9. “AUTO” mode
Fig. 4-9-15 Point trace screen in PTP motion mode (with auxiliary axis)
Operation
2) Use the cursor (↑/↓) keys and F 14 (AXIS←) or F 15 (AXIS→) key so that the
point value of the robot axis to be checked is highlighted.
To perform trace for the robot main axes:
Fig. 4-9-16 Point trace screen in PTP motion mode (with auxiliary axis)
n IfNOTE
the SCARA robot is selected and the
AUTO>POINT [RIGHTY] 50/100% [MG][S0H0J]
hand system flag is set for the point .
————————————x———————y———————z———————r———
data, then this hand system will have P3 = 150.50 64.53 21.78 -45.14
priority over the current arm type.
P4 = 96.65 -224.89 43.31 28.79
P5 = -63432 19735 6243 22642
COMNT : [LEFTY]
[POS] 0 0 0 0
PTP JUMP VEL+ VEL-
w Upon
WARNING
pressing the key, the
3) Press the START key, and the robot moves by PTP motion to the specified point position.
START The trace speed is one tenth of the automatic movement speed. If the SCARA robot is
robot starts to move. To avoid selected and the hand system flag is set for the point data, then this hand system will
danger, do not enter the robot
movement range. have priority. To stop the trace, press the STOP key.
4-37
9. “AUTO” mode
Fig. 4-9-18 Point trace screen in ARCH motion mode (with no auxiliary axis)
4 P5
COMNT :
= -63432 19735 6243
[LEFTY]
22642
[POS] 0 0 0 0
Operation
Fig. 4-9-19 Point trace screen in ARCH motion mode (with no auxiliary axis)
3) Press the F 2 (A.POS) key and set the arch motion position.
n IfNOTE
Fig. 4-9-20 Point trace screen in ARCH motion mode (with no auxiliary axis)
the SCARA robot is selected and the
hand system flag is set for the point AUTO >POINT [RIGHTY] 50/100% [MG][S0H0J]
data, then this hand system will have ————————————x———————y——ARCH(z)——————r———
priority over the current arm type.
P3 = 150.50 64.53 21.78 -45.14
P4 = 96.65 -224.89 43.31 28.79
P5 = -63432 19735 6243 22642
COMNT : [LEFTY]
[POS] 0 0 0 0
Enter ARCH data> 20000
4) Use the cursor (↑/↓) keys to select the point number to be checked.
w Upon
WARNING
pressing the key, the
5) Press the START key to move the robot by arch motion to the specified point position.
START The trace speed is one tenth of the automatic movement speed. If the SCARA robot is
robot starts to move. To avoid selected and the hand system flag is set for the point data, then this hand system will
danger, do not enter the robot
movement range. have priority. To stop the trace, press the STOP key.
4-38
9. “AUTO” mode
Fig. 4-9-21 Point trace screen in ARCH motion mode (with auxiliary axis)
Operation
2) Press the F 6 (A.AXIS+) or F 7 (A.AXIS -) to select the axis to move by arch
motion.
The selected axis is indicated on the message line, for example “ARCH(z)” as shown
below.
Fig. 4-9-22 Point trace screen in ARCH motion mode (with auxiliary axis)
3) Press the F 2 (A.POS) key and set the arch motion position.
Fig. 4-9-23 Point trace screen in ARCH motion mode (with auxiliary axis)
n IfNOTE
the SCARA robot is selected and the
AUTO>POINT [RIGHTY] 50/100% [MG][S0H0J]
4) Use the cursor (↑/↓) keys and F 14 (AXIS←) or F 15 (AXIS→) key so that the
point value of the robot axis to be checked is highlighted.
w Upon
WARNING
pressing the key, the
5) Press the START key to move the robot by arch motion to the specified point position.
START (The auxiliary axis moves by PTP.) The trace speed is one tenth of the automatic
robot starts to move. To avoid movement speed. If the SCARA robot is selected and the hand system flag is set for
danger, do not enter the robot
movement range. the point data, then this hand system will have priority. To stop the trace, press the
STOP key.
4-39
9. “AUTO” mode
Fig. 4-9-24 Point trace screen in linear interpolation motion mode (with no auxiliary axis)
4 P5
COMNT :
= -63432 19735 6243
[LEFTY]
22642
[POS] 0 0 0 0
Operation
2) Use the cursor (↑/↓) keys to select the point number to be checked.
n IfNOTE
Fig. 4-9-25 Point trace screen in linear interpolation motion mode (with no auxiliary axis)
the SCARA robot is selected and the
hand system flag is set for the point AUTO >POINT [RIGHTY] 50/100% [MG][S0H0J]
data, then this hand system will have ————————————x———————y———————z———————r———
priority over the current arm type.
The sub robot cannot perform linear P3 = 150.50 64.53 21.78 -45.14
interpolation movement. P4 = 96.65 -224.89 43.31 28.79
P5 = -63432 19735 6243 22642
COMNT : [LEFTY]
[POS] 0 0 0 0
LINEAR JUMP VEL+ VEL-
w Upon
WARNING
pressing the key, the
3) Press the START key to move the robot by linear interpolation motion to the specified
START
robot starts to move. To avoid
point position. The trace speed is one tenth of the automatic movement speed. If the
danger, do not enter the robot SCARA robot is selected and the hand system flag is set for the point data, then this
movement range. hand system will have priority. To stop the trace, press the key.
STOP
4-40
9. “AUTO” mode
Fig. 4-9-26 Point trace screen in linear interpolation motion mode (with auxiliary axis)
Operation
2) Use the cursor (↑/↓) keys and F 14 (AXIS←) or F 15 (AXIS→) key so that the
point value of the robot axis to be checked is highlighted.
To perform trace for the robot main axes:
Fig. 4-9-27 Point trace screen in linear interpolation motion mode (with auxiliary axis)
n IfNOTE
the SCARA robot is selected and the AUTO>POINT [RIGHTY] 50/100% [MG][S0H0J]
hand system flag is set for the point ————————————x———————y———————z———————r———
data, then this hand system will have P3 = 150.50
. 64.53 21.78 -45.14
priority over the current arm type.
The sub robot cannot perform linear P4 = 96.65 -224.89 43.31 28.79
interpolation movement. P5 = -63432 19735 6243 22642
COMNT : [LEFTY]
[POS] 0 0 0 0
LINEAR JUMP VEL+ VEL-
w Upon
WARNING
pressing the key, the
3) Press the START key to move the robot by linear interpolation motion to the specified
START
point position. (The auxiliary axis moves by PTP.) The trace speed is one tenth of the
robot starts to move. To avoid
automatic movement speed. If the SCARA robot is selected and the hand system flag
danger, do not enter the robot
movement range. is set for the point data, then this hand system will have priority. To stop the trace,
press the STOP key.
4-41
9. “AUTO” mode
5 MOVE P,P0
n The
NOTE
following command statements
>DO(25)=1_
4-42
9. “AUTO” mode
Page key
Switches the page display.
( / )
F1 SET Sets the break point. 4
F2 CANCEL Deletes the break point.
Searches for the line set with the break point.
Operation
F3 SEARCH
F6 JUMP Shows the program listing from specified line.
F7 FIND Specifies the character string to be found.
Finds the specified character string searching backwards from the cursor
F8 FIND+
position.
Finds the specified character string searching forwards from the cursor
F9 FIND-
position.
2) Use the cursor keys to select the line number on which a break point is to be set.
4-43
9. “AUTO” mode
n NOTE
• Up to 4 break points can be set in
3) To find the line number on which another break point was set, press the F 3
one program. These 4 break points (SEARCH) key.
4 cannot set in different programs.
However, when there is
“COMMON” program, 4 break
This function makes it easier to find a break point that you want to delete.
4-44
9. “AUTO” mode
Operation
3 DO2(0)=0
4 WAIT DI3(4,3,2)=3
5 MOVE P,P0
STEP SKIP NEXT
>
2) The program moves (skips) to the next line each time this key is pressed without
executing the command statement of the line number where the pointer is displayed.
w The
WARNING
robot may begin to move
2) Each time this key is pressed, the command statement of the highlighted line
number is executed. After execution, the pointer moves to the next line.
when NEXT is executed. To avoid
danger, do not enter the robot
If the command statement is a sub-routine or sub-procedure, it is executed at once.
movement range.
4-45
10. “PROGRAM” mode
Robot language programs can be edited, deleted and managed in “PROGRAM” mode.
y Guideline
q Mode hierarchy
Shows the current mode hierarchy. When the highest mode (“PROGRAM” in this
case) is highlighted it means the servomotor power is on. When not highlighted, it
means the servomotor power is off.
w Program name
Shows the program name currently selected.
e Message line
This line shows the number of digits of the program. If an error occurs, the error
message also appears here.
r Online command execution mark
When an online command is being executed, an “@” mark is displayed in the second
column on the second line. This mark changes to a dot ( . ) when the online command
ends.
t Selected line display
In the program listing, the line number to be edited is highlighted.
y Guideline
The contents assigned to function keys are shown highlighted. A message on what to
do next also appears here in some operation steps.
4-46
10. “PROGRAM” mode
Valid keys and submenu descriptions in “PROGRAM” mode are shown below.
Cursor key
Selects the program and scrolls the screen.
(↑/↓)
Page key
Switches the page display.
( / )
F1 EDIT Edits the program.
F3 DIR Displays the program data.
F5 COMPILE Compiles the program.
F6 JUMP Displays the program listing from a specified line.
F7 FIND Specifies the character string to be found.
n Refer
NOTE
F8 FIND+
Finds the specified character string searching backwards from the cursor
to the separate “Programming
Manual” for details on the
programming language.
position.
Finds the specified character string searching forwards from the cursor
4
F9 FIND-
position.
Operation
F13 ERR.RST Allows editing if the selected program is destroyed.
>>
2) Pressing the page ( << , >> , , ) key scrolls one page screen at a
time.
4-47
10. “PROGRAM” mode
2) Use the cursor keys to move the cursor to the position to be edited and enter a
program command with the MPB.
A maximum of 75 characters can be entered on one line.
n Program
NOTE
editing is finished when any
Fig. 4-10-2 “PROGRAM>EDIT” mode
<<
———————————————————————————————————————————
keys, or ESC key is pressed during 1 ’***** TEST2 PROGRAM *****
program editing.
Operation
2 GOSUB *SUBPROG
A maximum of 9999 lines can be
written in one program as long as the 3 DO2(0)=0
program size is within about 98 4 WAIT DI3(4,3,2)=3
Kbytes.
5 MOVE P,P0 ’ORIGIN
SELECT COPY CUT PASTE BS
Pressing the key finishes the program input for one line and moves the cursor to
the beginning of the next line.
4-48
10. “PROGRAM” mode
Valid keys and submenu descriptions in “PROGRAM > EDIT” mode are shown below.
Cursor key
Moves the cursor and scrolls the screen.
(↑/↓)
Page key
Switches the page display.
( / )
INS Switches between Insert and Overtype modes.
L.INS Inserts one blank line.
DEL Deletes one character.
L.DEL Deletes one line.
USER Displays the user function key.
ESC Ends program editing.
key
Finishes the program input for one line and moves the cursor to the beginning
of the next line.
4
F1 SELECT Selects the starting line for copy or cut.
Operation
F2 COPY Copies the selected line and temporarily stores it in a buffer.
F3 CUT Cuts the selected lines and temporarily stores it in a buffer.
F4 PASTE Inserts the buffer data directly prior to the cursor line.
F5 BS Backs the cursor and deletes the preceding character.
F6 JUMP Displays the program listing from the specified line.
F7 FIND Specifies the character string to be found.
Finds the specified character string searching backwards from the cursor
F8 FIND+
position.
Finds the specified character string searching forwards from the cursor
F9 FIND-
position.
4-49
10. “PROGRAM” mode
<<
>>
2) Pressing the page ( << , >> , , ) key moves the cursor one page
screen at a time.
6 MOVE P,P1
7 DO2(1)=1
SELECT COPY CUT PASTE BS
4-50
10. “PROGRAM” mode
Operation
10.2.3 Inserting a line
[Procedure]
Pressing the L.INS (= LOWER + INS ) key in “PROGRAM > EDIT” mode inserts a
blank line at the line previous to the cursor position.
Fig. 4-10-6 Inserting a line
4-51
10. “PROGRAM” mode
4 5 MOVE P,P1
6 DO2(1)=1
7 DELAY 1000
Operation
For example, when the F 2 (GOTO *) key is pressed in Fig. 4-10-8, the character
string for “GOTO *” is entered at the cursor position.
4-52
10. “PROGRAM” mode
Operation
Fig. 4-10-9 Specifying the copy/cut lines
4-53
10. “PROGRAM” mode
4 4 DO(20)=1
5 DELAY 1000
SELECT COPY CUT PASTE BS
Operation
10.2.12 Backspace
[Procedure]
Pressing the F 5 (BS) key in “PROGRAM>EDIT” mode backs the cursor and deletes
the preceding character.
When the cursor is at the beginning of a line, it connects to the end of the previous line.
However, nothing is changed if the number of characters on the connected line exceeds
75 characters.
4-54
10. “PROGRAM” mode
Operation
2) Enter the line number to jump to and press the key.
The program is then displayed from the specified line.
4-55
10. “PROGRAM” mode
2) Enter the character string you want to search for and press the key.
A maximum of 20 characters can be used.
4 1 2 3
———————————————————————————————————————————
1 ’***** TEST2 PROGRAM *****
2 GOTO *_’
Operation
3 DO2(0)=0
4 WAIT DI3(4,3,2)=3
5 MOVE P,P0 ’ORIGIN
Character string >MOV_
Search starts from the cursor position towards the end of the program and stops at the
first matching character string.
4-56
10. “PROGRAM” mode
10.3 Directory
n ANOTE
maximum of 100 programs can be
When the F 3 (DIR) key is pressed in “PROGRAM” mode, information on each
program appears as shown below.
stored.
Fig. 4-10-17 Program information (1)
Operation
data.
(Press the →
key to return to the previous display.)
n The
NOTE
date and time are updated when
PROGRAM >DIR <TEST1 >
Item Description
Indicates the serial number of the program. The number of the program which is
No.
currently selected is highlighted (reversed background).
DATE Shows the date when the program was made or edited.
TIME Shows the time when the program was made or edited.
4-57
10. “PROGRAM” mode
Valid keys and submenu descriptions in “PROGRAM >DIR” mode are shown below.
Cursor key
Switches between the program information display and the date/time display.
(← / →)
Page key
Switches to other screens.
( / )
4 F8
F10
RENAME
ATTRBT
Renames the program.
Changes the program attribute.
F11 OBJECT Shows the object program information.
Operation
4-58
10. “PROGRAM” mode
n The
NOTE
following program names have
Fig. 4-10-19 Registering a new program
n Program
NOTE
10.3.3 Directory information display
4
names can be up to 8 [Procedure]
characters consisting of a combination
Operation
of alphanumeric characters (0 to 9, A In “PROGRAM>DIR” mode, press the F 5 (INFO) key to enter
to Z) and underscores ( _ ).
“PROGRAM>DIR>INFO” mode. The following information on the selected program
appears.
Fig. 4-10-20 Program information
Item Description
Source (use/sum) Displays a count of used bytes and bytes available for source program and point data.
Object (use/sum) Displays a count of used bytes and bytes available for object program.
Sequence Displays a count of used bytes and bytes available for sequence object program. (8
(use/sum) bytes are used for one circuit of sequence program.)
Number of program Displays the number of programs.
Number of points Displays the number of points that have been set. (28 bytes are used for one point.)
4-59
10. “PROGRAM” mode
n Program
NOTE
names can be up to 8
3 PARTS100 38 843 RW
4 TEST100 100 1968 RW
characters and consist of a
Enter program name >TEST3
combination of alphanumeric
characters (0 to 9, A to Z) and
underscores ( _ ).
4) Press the key to make a copy.
4-60
10. “PROGRAM” mode
Operation
2 *TEST2 50 907 RW
3 PARTS100 38 843 RW
4 TEST100 100 1968 RW
Erase program OK? YES NO
c CAUTION
• Programs with an “RO (read No. NAME LINE BYTE RW/RO
only) attribute cannot be erased. 1 *TEST2 50 907 RW
When these programs must be
erased, change the attribute. 2 PARTS100 38 843 RW
• To change the program attribute, 3 TEST100 100 1968 RW
refer to “10.3.7 Changing the 4 TEST200 80 1525 RW
program attribute”.
NEW INFO
4-61
10. “PROGRAM” mode
1 TEST1 55 952 RW
2 *TEST2 50 907 RW
3 PARTS100 38 843 RW
4 TEST100 100 31968 RW
Enter program name >TEST_
4-62
10. “PROGRAM” mode
1. RW (read or write)
Program contents can be edited and erased.
This is automatically specified as a default when a program name is registered.
2. RO (read only)
Program contents cannot be edited or erased.
[Procedure]
1) In “PROGRAM>DIR” mode, use the cursor (↑/↓) keys to select the program with the
4
attribute to be changed.
Operation
2) Press the F 10 (ATTRBT) key to enter “PROGRAM>DIR>ATTRBT” mode.
A confirmation message appears on the guideline.
4-63
10. “PROGRAM” mode
n Refer
NOTE No. NAME LINE BYTE RW/RO
4-64
10. “PROGRAM” mode
Operation
*M_F6:'DO(25)MOMENTARY
DO(25)=1
DO(25)=0
*M_F7:'DO(26)MOMENTARY
DO(26)=1
DO(26)=0
*M_F8:'DO(27)MOMENTARY
DO(27)=1
DO(27)=0
*M_F9:'DO2()ON
DO2()=255
*M_F10:'DO2()OFF
DO2()=0
*M_F11:'OPEN
DO3(0)=&B1
*M_F12:'CLOSE
DO3(0)=O
*M_F13:'AND
DO3(1)=1 & DO3(0)
*M_F14:'DI4 –> DO4
DO4()=DI4()
*M_F15:'DO5INC
DO5()=DO5()+1
'**********************************
*PF 1 : 'MOVE P,P
*PF 2 : 'MOVE L,P
*PF 3 : 'GOTO *
*PF 4 : 'DELAY
*PF 5 : 'WAIT
*PF 6 : 'GOSUB *
*PF 7 : 'RETURN
*PF 8 : 'PRINT
*PF 9 : 'SPEED
*PF10:'HALT
*PF11:'IF THEN
*PF12:'ELSE
*PF13:'ENDIF
*PF14:'FOR = TO
*PF15:'NEXT
4-65
10. “PROGRAM” mode
10.4 Compiling
To compile the program and create an executable object program, follow the procedure
below. The object program allows you to check input errors or bugs after program editing.
[Procedure]
1) In “PROGRAM>DIR” mode, select the program to compile with cursor (↑/↓) keys
and press the ESC key.
If an error is found in the command statements, the program listing for that line appears
along with an error message, and the compiling stops. When the compiling ends
normally, an object program has been made. The previous object program was deleted.
n Even
NOTE
if the specified program is yet not
PROGRAM
2
<TEST1
3
>
5.1:Syntax error
———————————————————————————————————————————
compiled, it is compiled automatically
when you move to “AUTO” mode. 5 MOVE P,1P1
6 DO2(1)=1
7 DELAY 1000
8 DO2(1)=0
9 HALT
EDIT DIR COMPILE
4-66
10. “PROGRAM” mode
Operation
mode.
3) When the message “Enter program name >“ appears on the guideline, enter
“FUNCTION” following this message and press the key.
4-67
10. “PROGRAM” mode
“MANUAL” mode.
*P_F<n>:’<character string>
Example)
*P_F2:’MOVE, P ......... Character string “MOVE, P” is assigned to the F 2
key.
*P_F8:’DELAY............ Character string “DELAY” is assigned to the F 8 key.
4-68
10. “PROGRAM” mode
*M_F<n>:’<character string>
<I/O statement 1>
<I/O statement 2>
Example) 4
n <I/O statement 2> may be omitted. If
NOTE *M_F2:’MOMENT ...... Character string “MOMENT” is assigned to the F 2
key.
Operation
omitted the <I/O statement 1>will be
executed when the key is pressed, but
nothing will be executed when
DO (20) =1 ................... DO (20) is turned ON when the F 2 key is pressed.
released.
DO (20) =0 ................... DO (20) is turned OFF when the F 2 key is released.
*M F14:’ALTER .......... Character string “ALTER” is assigned to the F 14 key.
DO (20) =~DO (20) ..... DO (20) is highlighted when the F 14 key is pressed.
In the above example, “ALTER” defines an “alternate” type function, and “MOMENT” a
“momentary” type function.
A <character string> of up to 65 characters can entered. However, up to 7 characters
following the colon ( : ) are displayed on the function key menu.
n NOTE
• In one “FUNCTION” program,
Fig. 4-10-32 Registering user functions
4-69
10. “PROGRAM” mode
Fig. 4-10-33
n NOTE
• This function is enabled for each
2) Press the F 4 (YES) key to reset the error.
The program can be edited after resetting the error.
program.
• This reset function does not work Press the F 5 (NO) key if you want to cancel the error reset.
if an error “9.3 Memory
destroyed” occurs. In this case,
initialize the memory.
4-70
11. “MANUAL” mode
Point data and shift data coordinates can be defined and edited in “MANUAL” mode.
The initial “MANUAL” mode screens are shown in Fig. 4-11-1, Fig. 4-11-2 and Fig. 4-
11-3.
Fig. 4-11-1 “MANUAL” mode (one-robot setting)
r SHIFT/HAND
q Mode hierarchy w Manual movement /coordinate units
speed
e Robot group t Message
y Online line
command
execution mark MANUAL 50%[MG][S0H0X]
u Sequence s@ —————————————————————————————————————
program Current position
execution mark
i Current
*Mx=
*Mr=
0.00 *My=
0.00
0.00 *Mz= 0.00
4
position
Operation
POINT PALLET VEL+ VEL-
o Guideline
r SHIFT/HAND
q Mode hierarchy w Manual movement /coordinate units
speed
e Robot group t Message
y Online line
command
execution mark MANUAL 50/50%[MG][S0H0X]
u Sequence s@ —————————————————————————————————————
program Current position
execution mark
*Mx= 0.00 *My= 0.00
i Current
*Sx= 0.00 *Sy= 0.00
position
r SHIFT/HAND
q Mode hierarchy w Manual movement /coordinate units
speed
e Robot group t Message
y Online line
command
execution mark MANUAL 50%[MG][S0H0X]
u Sequence s@ —————————————————————————————————————
program Current position
execution mark
*Mx= 0.00 *My= 0.00 *Mz= 0.00
*mr= 0.00
i Current
position
4-71
11. “MANUAL” mode
q Mode hierarchy
Shows the current mode hierarchy. When the highest mode (“MANUAL” in this case)
is highlighted it means the servomotor power is on. When not highlighted it means the
servomotor power is off.
w Manual movement speed
Shows the robot movement speed selected for manual operation.
When two robots (main and sub robots) are specified, two speeds are displayed for
“ main group / sub group ”, with the currently selected group highlighted.
e Robot group
This shows the robot group currently selected for manual movement.
When one robot is specified, only “[MG]” (main group) appears.
When two robots are specified, the “[MG]” (main group) or “[SG]” (sub group) appears,
4 which can be switched with the ROBOT ( LOWER + MODE ) key.
r SHIFT/HAND/coordinate units
Operation
Shows the shift coordinate number, hand definition number and coordinate units. When
two robots are specified, the main group or sub group number and coordinate units
appear, which can be switched with the ROBOT ( LOWER + MODE ) key.
t Message line
If an error occurs, the error message appears here. A dashed line means return-to-
origin is incomplete. A solid line means return-to-origin return is complete.
y Online command execution mark
When an online command is being executed, a “@” mark is displayed in the second
column on the second line. This mark changes to a dot ( . ) when the online command
ends.
u Sequence program execution mark
When a sequence program is being executed, an “s” mark is displayed in the first
column on the second line.
i Current position
This shows the current position of the robot. When an "M" or "S" letter is followed by
a number it indicates the position in "pulse" units (integer display) and when an "x" to
"a" letter follows, it indicates "mm" units (decimal point display). When an asterisk
(*) appears at the left of the "M" and "S" letters, it indicates the origin sensor is on. An
asterisk also appears when no origin sensor is used.
An “M” letter means the main robot axis, and an “S” letter means the sub robot axis.
When auxiliary axes are specified, the lower-case letters “m” and “s” appear instead
of upper-case letters.
o Guideline
The contents assigned to function keys are shown highlighted. A message on what to
do next also appears here in some operation steps.
4-72
11. “MANUAL” mode
Valid keys and submenu descriptions in “MANUAL” mode are shown below.
F9 VEL++
Increases manual movement speed for the selected robot group in 1%
increments.
4
Decreases manual movement speed for the selected robot group in 1%
Operation
F10 VEL--
decrements.
ROBOT
( LOWER Switches the robot group.
+ MODE )
4-73
11. “MANUAL” mode
w The
WARNING
robot starts to move when a
11.1 Manual movement
Jog key is pressed. To avoid In “MANUAL” mode, you can manually move the robot with the Jog keys as explained
danger, do not enter the robot
movement range.
below.
1. Manual movement when return-to-origin has been completed
(1) When the current position is displayed in “pulse” units:
n •NOTE
When two robots (main and sub
A letter "J" is displayed on the upper right of the MPB screen.
robots) are specified, check the Fig. 4-11-4 Display shown in "pulse" units (J)
currently selected robot group on the
MPB before performing manual
movement. If the selected robot group MANUAL 50%[MG][S0H0J]
is wrong, press the ROBOT ( LOWER ————————————————————————————————————————
+ MODE ) key to change the robot
group. Current position
• For details on the soft limits, refer to *M1= 12521 *M2= -52204 *M3= 3021
4 •
"12.1.2 Axis parameters" in this
chapter.
When the current position is
displayed in “pulse” units, the robot
Operation
MANUAL 50%[MG][S0H0X]
————————————————————————————————————————
Current position
*Mx= 151.05 *My= -35.27 *Mz= 49.23
MANUAL 50%[MG][S0H1T]
————————————————————————————————————————
Current position
*Mx= 204.73 *My= 81.40 *Mz= 25.37
*Mr= 32.51
4-74
11. “MANUAL” mode
When the other Jog keys are pressed, the robot moves the same way as when "X" is
displayed. 4
Fig. 4-11-7 Robot movement in "Tool coordinate" mode (example)
Operation
Y
MANUAL>HAND 50% [MG][S0H1T]
————————————1———————2———————3———————4———
H0 = 0.00 150.00 0.00 R
X H1 = -90.00 100.00 0.00 R
H2 = 0 0.00 0.00
-90.00 degrees
H3 = 0 0.00 0.00
100.00mm
HAND 1
If the above hand is defined, the robot moves with Jog keys as illustrated below.
Robot movement with #1+ to #2- keys Robot movement with #4+ and #4- keys
Y Y
#2+ #1+
#4-
#4+
#1- #2-
X X
Each time a Jog key is pressed, the robot moves a specified distance (inching
movement). When the Jog key is held down, the robot keeps moving. The robot stops
when the Jog key is released or either of the soft limit or shift coordinate range is
reached.
The robot stops when the Jog key is released or the soft limit is reached.
The movement distance (inching distance) is equal to the manual movement speed
setting (%) multiplied by 0.01mm or 0.01 deg.
[Example] When manual movement speed is 20%:
Inching distance in "mm" units = 0.20mm
4-75
11. “MANUAL” mode
If robot movement beyond the +/- soft limits is attempted with the Jog keys, the error
message “2.1: Over soft limit” appears and the robot does not move. Likewise, if
robot movement beyond the shift coordinate range is attempted, the error message
“2.11: Exceeded shift coord. range” appears and the robot does not move.
If the current position is outside the soft limits, the error message “2.1: Over soft
limit” also appears and the robot does not move.
4
n IfNOTE
return-to-origin is incomplete, the
(2) When the current position is displayed in “mm” units:
The robot does not move with the Jog keys. The current position display
Operation
4-76
11. “MANUAL” mode
c InCAUTION
the case of SCARA robots, it
The axis data for three points is displayed on the screen along with a point comment on
the selected point number. To see the other data, scroll the screen with the cursor keys or
cannot be guaranteed that the robots page keys.
will move to the same position if a
different hand system is used to move
to a point data on the Cartesian
coordinates (millimeter units).
↑
→
↓
→
Scrolls up or down one line at a time.
Scrolls right or left one character at a time.
4
>>
<<
Operation
<< >> Scrolls right or left one page at a time.
The 5-digit area on the left side shows the point numbers, with the point number for
editing shown highlighted.
The hand system will appear in the sixth line when the SCARA robot is selected and a
hand system flag of the extended setting is set.
Fig. 4-11-8 Point data
4-77
11. “MANUAL” mode
Valid keys and submenu descriptions in “MANUAL>POINT” mode are shown below.
Page key
Switches to other screens.
<<
>>
( / )
F1 EDIT Enters point data with keys.
F2 TEACH Enters point data by teaching.
F3 JUMP Shows the specified point data.
Increases manual movement speed for the selected robot group in steps.
F4 VEL+
(1→5→20→50→100 %)
Moves the cursor to the right to select another axis. (Enabled only when
F15 AXIS→
auxiliary axis is added.)
ROBOT
( LOWER Switches the robot group.
+ MODE )
4-78
11. “MANUAL” mode
n NOTE
• Enter all point data for the X-axis
• To enter the data in Cartesian coordinates (“mm” units)
Enter a number consisting of an integer portion of up to 5 digits and having 2 or less
to b-axis. If omitted, “0” will be
automatically entered for that
places below the decimal point. 4
axis. (Even if the input data is less than 8 digits, it will be displayed in 8 digits when the
• The error message “Digit number number of display digits is set to 8 in “SYSTEM>PARAM” mode.)
Operation
error” appears when the data
format is wrong. Enter it in the : ±###.##,±####.#,±#####.
correct format. (±#####.##,±#####.#,±#######.)
To set the SCARA robot and set a hand system flag of the extended setting, set 1 or 2
at the end of the b axis data. If a value other than 1 or 2 is set, or if no value is
n ToNOTE
set the SCARA robot and set the
designated, then 0 will be set to indicate that no hand system flag was set.
hand system flag in the point data, set 1: Indicates that point has been set with RIGHTY (right-handed system).
1 (RIGHTY: right-handed system) or 2 2: Indicates that point has been set with LEFTY (left-handed system).
(LEFTY: left-handed system) at the end
of the b axis data setting.
>>
<<
4) Press the key, cursor up/down (↑/↓) keys or page up/down ( , )
keys to finish the point data input.
Press the ESC key if you want to cancel the point data input.
Page key
Switches to other screen.
<<
>>
( / )
INS Toggles between Insert mode and Overwrite mode.
DEL Deletes one character on the cursor position.
F1 UNDO Restores the point data.
F3 JUMP Jumps to the specified point number.
[Procedure]
During point data editing, pressing the F 1 (UNDO) key reverses the last data input
and restores the preceding data.
This function is enabled only on lines that are not yet complete.
4-79
11. “MANUAL” mode
n Point
NOTE
data teaching cannot be
11.2.2 Point data input by teaching
performed when return-to-origin is The current position of the robot can be obtained as point data by teaching.
incomplete. Perform point teaching
after performing absolute reset.
When no auxiliary axis is used:
[Procedure]
1) In “MANUAL> POINT” mode, use the cursor (↑/↓) keys to select the point number
to obtain point data.
w The
WARNING
robot starts to move when a
2) Use the Jog keys to move the robot arm.
As the arm moves, the current position data on the 7th line on the screen changes.
Jog key is pressed. To avoid
danger, do not enter the robot
movement range. 3) When the arm arrives at the target point, press the F 2 (TEACH) key.
Teaching is performed so that the current robot position data is allotted to the
currently selected point number.
c ToCAUTION
perform teaching at a point on the
After teaching, the pointer cursor moves down to the next line automatically.
The format for point data input by teaching is set to the currently selected coordi-
Cartesian coordinates (millimeter
units) with a SCARA robot, always
nate system.
use the correct hand system that
should actually be moved. Fig. 4-11-11 Point data teaching (with no auxiliary axis [2])
The robot cannot be guaranteed to
move to the same position if moving MANUAL>POINT 50% [MG][S0H0X]
with a hand system different from that
used for teaching. ————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 = 50.00 100.00 5.00 10.00
P9 = 122.62 -24.54 12.35 -23.11
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
EDIT TEACH JUMP VEL+ VEL-
4-80
11. “MANUAL” mode
4) When point data is already allotted to the currently selected point number, a
confirmation message appears on the guideline when the F 2 (TEACH) key is
pressed.
MANUAL>POINT>TEACH 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 = 50.00 100.00 5.00 10.00
P9 = 122.62 -24.54 12.35 -23.11
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
Overwrite point OK? YES NO
Press the F 4 (YES) key to perform the teaching. The specified point number
4
data is rewritten.
Operation
Press the F 5 (NO) key if you want to cancel the teaching input.
When teaching at P8
MANUAL>POINT 100%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 = 220.00 150.00 115.00 90.00
P9 = 400.00 200.00 15.00 -30.00
COMNT: [ ]
[POS] -100.00 400.00 50.15 111.23
EDIT TEACH JUMP VEL+ VEL-
4-81
11. “MANUAL” mode
2) Use the cursor (↑/↓) keys, F 14 (AXIS ←) or F 15 (AXIS →) key to select the
axes to perform point teaching.
As shown below, the point number at the left end should be highlighted when
teaching on all axes. When teaching on the standard axes, their point data values
should be highlighted. When teaching on the auxiliary its point data value should be
highlighted.
Note that an undefined point cannot be specified except for point numbers.
MANUAL>POINT 100%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 = 220.00 150.00 115.00 90.00
P9 = 400.00 200.00 15.00 -30.00
COMNT: [ ]
[POS] -100.00 400.00 50.15 111.23
EDIT TEACH JUMP VEL+ VEL-
MANUAL>POINT 100%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 = 220.00 150.00 115.00 90.00
P9 = 400.00 200.00 15.00 -30.00
COMNT: [ ]
[POS] -100.00 400.00 50.15 111.23
EDIT TEACH JUMP VEL+ VEL-
w The
WARNING
robot starts to move when a 3) Use the Jog keys to move the robot axis for teaching.
Jog key is pressed. To avoid As the arm moves, the current position data on the 7th line on the screen changes.
danger, do not enter the robot
movement range.
4-82
11. “MANUAL” mode
c ToCAUTION
perform teaching at a point on the
4) When the axis arrives at the target point, press the F 2 (TEACH) key.
Cartesian coordinates (millimeter Teaching is performed so that the current robot position data is allotted to the
units) with a SCARA robot, always currently selected point. The format for point data input by teaching is set to the
use the correct hand system that currently selected coordinate system. However, when teaching is performed on
should actually be moved. different axes, they must use the same coordinates as the teach points. Therefore, if
The robot cannot be guaranteed to
move to the same position if moving the point data is in “mm” units, then the current position must also be in “mm”
with a hand system different from that units.
used for teaching. When point data is already allotted to the currently selected point, a confirmation
message “Overwrite point OK?” appears on the guideline when the F 2
(TEACH) key is pressed.
Press the F 4 (YES) key to perform the teaching.
Press the F 5 (NO) key if you want to cancel the teaching,
Operation
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 = 220.00 150.00 115.00 90.00
P9 = 400.00 200.00 15.00 -30.00
COMNT: [ ]
[POS] 212.43 152.31 100.26 86.86
Overwrite point OK? YES NO
After teaching, the specified point number moves to the next line automatically.
MANUAL>POINT 100%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 = 212.43 152.31 100.26 86.86
P9 = 400.00 200.00 15.00 -30.00
COMNT: [ ]
[POS] 212.43 152.31 100.26 86.86
EDIT TEACH JUMP VEL+ VEL-
MANUAL>POINT 100%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 = 212.43 152.31 100.26 90.00
P9 = 400.00 200.00 15.00 -30.00
COMNT: [ ]
[POS] 212.43 152.31 100.26 86.86
EDIT TEACH JUMP VEL+ VEL-
4-83
11. “MANUAL” mode
MANUAL>POINT 100%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 = 220.00 150.00 115.00 86.86
P9 = 400.00 200.00 15.00 -30.00
n Point
NOTE
data teaching cannot be
COMNT: [ ]
performed if return-to-origin is [POS] 212.43 152.31 100.26 86.86
incomplete. EDIT TEACH JUMP VEL+ VEL-
2) Move the robot by hand to the target point and perform point teaching in
“MANUAL>POINT” mode.
For point data teaching methods, refer to the previous section “11.2.2 Point data
n When
NOTE
the robot servo is off, automatic input by teaching”. (In this procedure you move the robot by hand since the Jog
and manual operation cannot be keys cannot be used.)
performed. There are two methods for
turning on the robot servo: One is to
use the MPB and the other is to use the 11.2.4 Point jump display
dedicated input.
Refer to "14. "UTILITY" mode" in this
chapter, or refer to "1. Standard I/O
[Procedure]
interface overview" in Chapter 5.
1) Press the F 3 (JUMP) key in “MANUAL>POINT” mode.
The message “Enter point no.>“ appears on the guideline.
MANUAL>POINT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 = 50.00 100.00 5.00 10.00
P9 = 122.62 -24.54 12.35 -23.11
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
Enter point no.>100_
4-84
11. “MANUAL” mode
n Valid
NOTE
point numbers are from 0 to
2) Enter the point number to jump to, and press the key.
9999. A jump is made so that the point data is displayed from the designated point
number.
MANUAL>POINT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P100 = 0.00 0.00 0.00 0.00
P101 =
P102 = 10000 20000 10000 0
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
EDIT TEACH JUMP VEL+ VEL-
4
11.2.5 Copying point data
Operation
Point data can be copied under another point number.
[Procedure]
n IfNOTE
a hand system flag is set in the point
1) Press the F 6 (COPY) key in “MANUAL>POINT” mode.
The message “Copy(####-####,####)>“ appears on the guideline.
data, the hand system flag will also be
copied.
Fig. 4-11-23 Copying point data (1)
4-85
11. “MANUAL” mode
n Valid
NOTE
point numbers are from 0 to
2) Use the 0 to 9 , – and , keys to enter the point number range
9999. for the copy source and the point number for the copy destination in the following
format and press the key.
“(copy start number) – (copy end number), (copy destination number)”
For example, to copy the data between P30 and P34 onto the lines after P50, enter
“30 - 34, 50” and press the key.
A confirmation message appears on the guideline.
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
(30-34,50)Copy OK? YES NO
4-86
11. “MANUAL” mode
n Valid
NOTE
point numbers are from 0 to
2) Use the 0 to 9 and – keys to specify the point number range in the
9999. following format and press the key.
“(erase start number) - (erase end number)”
For example, to erase the data between P30 and P34, enter “30-34” and press the
key.
A confirmation message appears on the guideline.
Operation
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
(30-34)Erase OK? YES NO
3) Press the F 4 (YES) key to erase the data. The point data in the specified range
is erased.
Press the F 5 (NO) key if you want to cancel erasure.
4-87
11. “MANUAL” mode
n NOTE
• Point comments can be entered for
Press the F 12 (COMMENT) key in “MANUAL>POINT” mode.
point numbers having no data. The data display on the screen does not change (same as “MANUAL>POINT” mode).
• A point comment can be up to 15 The 5-digit area on the left shows point numbers, with the currently selected point num-
characters. ber highlighted.
Fig. 4-11-27
MANUAL>POINT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 =
P9 = 122.62 -24.54 12.35 -23.11
4 COMNT:
[POS] 50.00 100.00
[
5.00
]
10.00
EDIT TEACH JUMP VEL+ VEL-
Operation
Valid keys and submenu descriptions in “MANUAL > POINT” comment mode are shown
below.
Page key
Switches to other screens.
<<
>>
( / )
F1 EDIT Edits point comments.
F2 TEACH Enters point data by teaching.
F3 JUMP Displays the specified (jumped) data.
Increases manual movement speed for the selected robot group in steps.
F4 VEL+
(1→5→20→50→100 %)
Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
(100→50→20→5→1 %)
ROBOT
( LOWER Switches the robot group.
+ MODE )
4-88
11. “MANUAL” mode
n NOTE
• For point comments, it is advisable
[Procedure]
to enter a character string that is 1) In “MANUAL>POINT>COMMENT” mode, use the cursor (↑/↓) keys to select the
easy to understand. point to edit or enter a comment.
• A point comment can be up to 15
characters.
2) Press the F 1 (EDIT) key in “MANUAL>POINT>COMMENT” mode.
An edit cursor appears on the guidline.
Fig. 4-11-28
MANUAL>POINT>COMMENT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P7
P8
= 100.00
=
250.00 15.00 30.00
4
P9 = 122.62 -24.54 12.35 -23.11
Operation
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
Comment>_
4) Press the enter key to finish the point comment input and display it.
Press the ESC key if you want to cancel the comment input.
4-89
11. “MANUAL” mode
[Procedure]
n Valid
NOTE
point numbers are from 0 to
1) Press the F 3 (JUMP) key in “MANUAL>POINT>COMMENT” mode.
The message “Enter point no. >” appears on the guideline.
9999.
Fig. 4-11-29
MANUAL>POINT>COMMENT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 =
P9 = 122.62 -24.54 12.35 -23.11
4 COMNT:
[POS] 50.00 100.00
[
5.00
]
10.00
Enter point no.>107_
Operation
2) Enter the point comment to jump to, and press the key.
A jump is made to the designated point and its comment is then displayed.
Fig. 4-11-30
MANUAL>POINT>COMMENT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P107 = 340.05 250.03 115.00 34.54
P108 = 340.05 200.05 115.00 34.54
P109 = 122.62 -24.54 12.35 -23.11
COMNT:WAIT_POS 08 [ ]
[POS] 50.00 100.00 5.00 10.00
EDIT TEACH JUMP VEL+ VEL-
4-90
11. “MANUAL” mode
For example, to copy the point comments between P7 and P16 onto the lines after 4
P107, enter “7 - 16, 107” and press the key.
Operation
Fig. 4-11-31
MANUAL>POINT>COMMENT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 =
P9 = 122.62 -24.54 12.35 -23.11
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
Copy(####-####,####)>7-16,107_
Fig. 4-11-32
MANUAL>POINT>COMMENT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 =
P9 = 122.62 -24.54 12.35 -23.11
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
(7-16,107)Copy OK? YES NO
4-91
11. “MANUAL” mode
For example, to erase the data between P7 and P16, enter “7-16” and press the
4 key.
Fig. 4-11-33
Operation
MANUAL>POINT>COMMENT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 =
P9 = 122.62 -24.54 12.35 -23.11
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
Erase(####-####)>7-16_
Fig. 4-11-34
MANUAL>POINT>COMMENT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
P8 =
P9 = 122.62 -24.54 12.35 -23.11
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
(7-16)Erase OK? YES NO
4-92
11. “MANUAL” mode
2) Enter the character string you want to search for, and press the key.
A maximum of 15 characters can be used.
Fig. 4-11-35
MANUAL>POINT>COMMENT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P7 = 100.00 250.00 15.00 30.00
4
P8 =
Operation
P9 = 122.62 -24.54 12.35 -23.11
COMNT: [ ]
[POS] 50.00 100.00 5.00 10.00
Character string >WAIT_
3) Search starts from the cursor position towards the end of the program and stops at
the first matching character string.
Fig. 4-11-36
MANUAL>POINT>COMMENT 50%[MG][S0H0X]
————————————x———————y———————z———————r———
P334 = 100.00 250.00 15.00 30.00
P335 =
P336 = 122.62 -24.54 12.35 -23.11
COMNT:WAIT_PICKUP [ ]
[POS] 50.00 100.00 5.00 10.00
EDIT TEACH JUMP VEL+ VEL-
4-93
11. “MANUAL” mode
Fig. 4-11-37
c This
CAUTION
function resets an error, but does MANUAL>POINT 50% [MG][S0H0X]
not restore the point data. A problem ————— 9.2:Point data destroyed—————————
is probably occurring in the point
P30 = 100.00 250.00 15.00 30.00
data, so check and correct the point
data in “MANUAL>POINT>EDIT” P31 = 50.00 100.00 15.00 10.00
4 mode. P32
COMNT:
= 122.62 -24.54 12.35
[ ]
-23.11
n This
NOTE
reset function does not work if an
2) Press the F 4 (YES) key to reset the error.
error “9.3 Memory destroyed” occurs. Point data can be edited after resetting the error.
In this case, initialize the memory. Press the F 5 (NO) key if you want to cancel the error reset.
4-94
11. “MANUAL” mode
n NOTE
• A total of 20 pallets can be
A total of 20 pallets (definition numbers 0 to 19) can be defined to assign a point data area
defined.
to each pallet. Each pallet is generated (outlined) by using 5 points (P[1] to P[5] as shown
• The maximum number of points below). The maximum number of points that can be defined in one pallet is 32767
that can be defined in one pallet is (=NX*NY*NZ).
32767.
• Data in the point data area is used Fig. 4-11-38
for pallet definition.
P[5]
P[3]
4
P[4]
Operation
NZ
NY
P[1] P[2]
NX
Pallet number Point number used Pallet number Point number used
PL0 P3996 to P4000 PL10 P3946 to P3950
n When
PL1 P3991 to P3995 PL11 P3941 to P3945
NOTE
two robots (main and sub PL2 P3986 to P3990 PL12 P3936 to P3940
robots) are specified, pallet definitions PL3 P3981 to P3985 PL13 P3931 to P3935
can be shared between them. Pallet
definitions cannot be used with MULTI PL4 P3976 to P3980 PL14 P3926 to P3930
type robots. PL5 P3971 to P3975 PL15 P3921 to P3925
PL6 P3966 to P3970 PL16 P3916 to P3920
PL7 P3961 to P3965 PL17 P3911 to P3915
PL8 P3956 to P3960 PL18 P3906 to P3910
PL9 P3951 to P3955 PL19 P3901 to P3905
Fig. 4-11-39
PL0 =SET
PL1 =
PL2 =SET
PL3 =
[POS] 400.00 0.00 0.00 0.00
EDIT METHOD VEL+ VEL-
Pallet definition numbers marked “SET” mean that they have already been defined.
4-95
11. “MANUAL” mode
Valid keys and submenu descriptions in “MANUAL>PALLET” mode are shown below.
Page key
Switches to other screens.
<<
>>
( / )
F1 EDIT Edits pallet definitions.
F2 METHOD Sets the pallet definition point by teaching.
Increases manual movement speed for the selected robot group in steps.
F4 VEL+
(1→5→20→50→100 %)
Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
(100→50→20→5→1 %)
4 F6
F7
COPY
ERASE
Copies pallet definitions.
Deletes pallet definitions.
F9 VEL++
increments.
F15 PASSWD
ROBOT
( LOWER Switches the robot group.
+ MODE )
4-96
11. “MANUAL” mode
3) Use the cursor (↑/↓) keys to move the cursor to the position you want edit.
n The
NOTE
maximum number of points per
4) Use the 0 to 9 keys to enter the desired value.
pallet is 32767 (=NX*NY*NZ).
The maximum number of points per pallet must be within 32767 (=NX*NY*NZ).
Fig. 4-11-40 4
MANUAL>PALLET>EDIT 50%[MG][S0H0X]
Operation
PALLET NO. =PL0 [XY]
Used point =P3996-P4000
NX = 3
NY = 4
NZ = 5_
POINT
7) Press the ESC key to quit editing and return to “MANUAL>PALLET” mode.
4-97
11. “MANUAL” mode
n NOTE
• Each pallet is generated with 5
11.3.1.1 Point setting in pallet definition
points for pallet definition. In “MANUAL>PALLET>EDIT” mode, a screen like that shown below is displayed.
• These 5 points should be defined
in order from P[1] to P[5]. See Fig. 4-11-41
“11.3 Displaying, editing and
setting pallet definitions”. MANUAL>PALLET>EDIT 50%[MG][S0H0X]
POINT=P3996(P[1])-P4000(P[5])
P[1] = 98.87 -24.54 12.35 -23.11
P[2] = 122.62 -24.54 12.35 -23.11
P[3] = 98.62 -94.54 12.35 -23.11
[POS] 0.00 0.00 0.00 0.00
EDIT TEACH VEL+ VEL-
4 The 3rd line shows the point numbers and point data in the pallet definition.
Valid keys and submenu descriptions in this mode are shown below.
Operation
Increases manual movement speed for the selected robot group in steps.
F4 VEL+
(1→5→20→50→100 %)
Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
(100→50→20→5→1 %)
ROBOT
( LOWER Switches the robot group.
+ MODE )
4-98
11. “MANUAL” mode
n NOTE
• Each pallet is generated (outlined)
11.3.1.1.1 Editing the point in pallet definition
POINT=P3996(P[1])-P4000(P[5])
P[1] = _98.87 -24.54 12.35 -23.11
P[2] = 122.62 -24.54 12.35 -23.11
P[3] = 98.62 -94.54 12.35 -23.11
[POS] 0.00 0.00 0.00 0.00
UNDO 4
2) Use the cursor (←/→/↑/↓) keys to move the cursor to the position you want edit.
Operation
3) Use the 0 to 9 , + , – , . and SPACE keys to enter the
point data.
4) Press the key or cursor up/down (↑/↓) keys to finish the point data input.
Press the ESC key if you want to cancel the point data input.
Valid keys and submenu descriptions in this mode are shown below.
F1 undo Reverses the last data input and restores the preceding data.
4-99
11. “MANUAL” mode
n Pallets
NOTE
cannot be defined by teaching if
[Procedure]
1) Select the pallet number in “MANUAL>PALLET” mode with the cursor (↑/↓)
return-to-origin is incomplete. Perform
teaching after performing absolute keys.
reset.
3) Select the dimension of the pallet to be defined from “2-D” (plane) or “3-D” (solid).
Fig. 4-11-43
4 MANUAL>PALLET>METHOD 50%[MG][S0H0X]
2-D 3-D
w ToWARNING
avoid hazardous situations do
4) Move the robot work point to P[1] used in the pallet definition, and perform teach-
not enter the robot movement ing by pressing the key.
range when manipulating the
robot. Fig. 4-11-44
n NOTE
• Each pallet is generated (outlined) PALLET NO.=PL0 [XY]
with 5 points for pallet definition. Move arm to P[1] and press ENTER key
• Point data in the pallet definition
must be entered in “mm” units.
• The 5 points should be defined in
order from P[1] to P[5]. See [POS] 0.00 0.00 0.00 0.00
“11.3 Displaying, editing and
setting pallet definitions”. VEL+ VEL–
5) Perform teaching at P[2], P[3], P[4] and P[5] (only when “3-D” is selected) as in
step 4).
6) Enter the number of points NX between P[1] and P[2] on the pallet with a positive
integer.
Fig. 4-11-45
MANUAL>PALLET>METHOD 50%[MG][S0H0X]
4-100
11. “MANUAL” mode
7) Enter the number of points NY and NZ (only when “3-D” is selected) as in step 6).
Fig. 4-11-46
Operation
Valid keys and submenu descriptions in “MANUAL>PALLET>METHOD” mode are
shown below.
n NOTE
Valid keys Menu Function
• Each pallet is generated with 5 Increases manual movement speed for the selected robot group in steps.
points for pallet definition. F4 VEL+
(1→5→20→50→100 %)
• The 5 points should be defined in
order from P[1] to P[5]. See Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
“11.3 Displaying, editing and (100→50→20→5→1 %)
setting pallet definitions”.
F8 UNITCHG Switches between the current display units (mm or pulses).
Increases manual movement speed for the selected robot group in 1%
F9 VEL++
increments.
4-101
11. “MANUAL” mode
2) Press the F 6 (COPY) key and then enter the pallet number where you want to
copy the currently selected pallet definition.
Fig. 4-11-47
n NOTE
• Valid pallet numbers are from 0 to MANUAL >PALLET 50%[MG][S0H0X]
19.
• Pallet definition cannot be copied PL0 =SET
if the currently selected pallet is
PL1 =SET
4 undefined.
PL2 =SET
PL3 =
[POS] 0.00 0.00 0.00 0.00
Operation
Copy(PL NO.)>3_
Fig. 4-11-48
MANUAL>PALLET 50%[MG][S0H0X]
PL0 =SET
PL1 =SET
PL2 =SET
PL3 =
[POS] 0.00 0.00 0.00 0.00
PL1 -> PL3 Copy OK? YES NO
4-102
11. “MANUAL” mode
n Pallet
NOTE
definition cannot be deleted if
2) Press the F 7 (ERASE) key.
A confirmation message then appears asking if the currently selected pallet
the currently selected pallet is definition is to be deleted.
undefined.
Press the F 4 (YES) key to delete it.
Press the F 5 (NO) key if you want to cancel.
Fig. 4-11-49
MANUAL>PALLET 50%[MG][S0H0X]
4
Operation
PL0 =SET
PL1 =SET
PL2 =SET
PL3 =SET
[POS] 0.00 0.00 0.00 0.00
Erase OK? YES NO
4-103
11. “MANUAL” mode
4-104
11. “MANUAL” mode
By setting shift coordinates, the point data on the Cartesian coordinates (“mm” units) can
be shifted to any desired position within the robot work area. The work area can also be
n NOTE
• When two robots (main and sub
restricted in each direction.
robots) are specified, the shift data Up to 10 shift coordinates (shift coordinate numbers 0 to 9) can be set to shift the standard
can be shared between them. Shift
coordinate numbers can be set for
coordinates in the X, Y, Z and R (XY plane rotation) directions. Each shift coordinate can
each robot separately.
• A maximum of 10 shift coordinates
specify the robot operating area.
4
can be set per robot.
• Shift coordinate data format
Operation
Sn= ±###.## ±###.## ±###.## ±###.##
dX (mm) dY (mm) dZ (mm) dR (degrees)
(n=0 to 9)
When the shift amount is dX=0.00, dY=0.00, dZ=0.00, dR=0.00, the shift coordinates
equal the standard coordinates.
Fig. 4-11-50 Standard coordinates and shift coordinates
Standard coordinate
X
dR
–
dY Z-axis origin
in ate
ord dZ
co +
ift dX
n Shift
NOTE
coordinates cannot be used with
Sh
4-105
11. “MANUAL” mode
Upon entering “MANUAL>SHIFT” mode, a screen like that shown in Fig. 4-11-51, Fig.
4-11-52 or Fig. 4-11-53 appears.
The currently selected shift coordinate number is highlighted.
Fig. 4-11-51 “MANUAL>SHIFT” mode (one-robot setting)
4-106
11. “MANUAL” mode
Valid keys and submenu descriptions in “MANUAL>SHIFT” mode are shown below.
Page key
Switches to other screens.
<<
>>
( / )
F1 EDIT Edits the shift coordinates.
F2 RANGE Sets the shift coordinates range.
Increases manual movement speed for the selected robot group in steps.
F4 VEL+
(1→5→20→50→100 %)
Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
(100→50→20→5→1 %)
F6
F7
METHOD1 Makes setting 1 for shift coordinates.
METHOD2 Makes setting 2 for shift coordinates.
4
Increases manual movement speed for the selected robot group in 1%
Operation
F9 VEL++
increments.
ROBOT
( LOWER Switches the robot group.
+ MODE )
4-107
11. “MANUAL” mode
3) Use the cursor (←/→) key to move the cursor to the position you want to change.
n The
NOTE
shift coordinate data on which the
UNDO
<<
5) Press the key, cursor up/down (↑/↓) keys or page up/down ( , )
to “MANUAL>SHIFT” mode is used
as the shift coordinates for the keys to finish the data input.
currently selected robot group.
Press the ESC key if you want to cancel the data input.
7) Press the ESC key to quit editing and return to “MANUAL>SHIFT” mode.
4-108
11. “MANUAL” mode
[Procedure]
During shift coordinate data editing, pressing the F 1 (UNDO) key reverses the last
data input and restores the preceding data.
This function is enabled only on lines that are not yet complete.
Operation
• Minus side
n NOTE
• ”n” is a shift coordinate number. SMn= ±###.## ±###.## ±###.## ±###.##
[Example] dMX (mm) dMY (mm) dMZ (mm) dMR (degrees)
SP1 ...... Plus side work area of
shift coordinate S1 (n=0 to 9)
SM 2 .... Minus side work area of
shift coordinate S2 Fig. 4-11-55 Shift coordinate range
• When the plus and minus sides on
an axis (x, y, z, r) are both at 0.00,
the work area on that axis is not
be restricted.
X
Y
dM
Y
dP
X
dM
– dMZ
Z'
dPZ
dPX +
dPR
X' dMR Y Y'
4-109
11. “MANUAL” mode
4 3) Use the cursor (←/→) keys to move the cursor to the position you want to change.
Operation
n Enter
NOTE
all shift range data for x, y, z
4) Use the 0 to 9 , + , – ,
point data.
. and SPACE keys to enter the
<<
n The
NOTE
shift coordinate number selected
Press the ESC key if you want to cancel the data input.
when returning to
“MANUAL>SHIFT” mode is used as 6) To continue editing the shift coordinate range on the minus side, repeat steps 3) to
the shift coordinates for the currently
5).
selected robot group.
7) Press the ESC key to quit editing and return to “MANUAL>SHIFT” mode.
Valid keys and submenu descriptions for editing shift coordinates range are shown below.
4-110
11. “MANUAL” mode
[Procedure]
During editing of shift coordinate range data, pressing the F 1 (UNDO) key reverses
the last data input and restores the preceding data.
This function is enabled only on lines that are not yet complete.
Operation
n When
NOTE
two robots (main and sub X
robots) are specified, check the
currently selected robot group on the
MPB screen.
“[MG]” indicates the main robot
group is selected, and “[SG]” Point 1
indicates the sub robot group is (1st P)
selected. To change the robot group,
use the ROBOT ( LOWER + MODE ) key.
Point 2
(2nd P)
X' Y Y'
[Procedure]
1) In “MANUAL>SHIFT” mode, select the shift coordinate number with the cursor
(↑/↓) key.
4-111
11. “MANUAL” mode
w The
WARNING
robot starts to move when a
3) Use the Jog keys to move the robot arm tip to teach point 1. (Position it accurately.)
5) Determine teach point 2 with the same procedure as for teach point 1.
Operation
6) Select the plus/minus direction of teach point 1 towards point 2 by using the F 1
+X -X +Y -Y
n The
NOTE
Z-direction shift value is
7) When the coordinate direction is selected, the shift coordinate values (dX, dY, dZ,
dR) are automatically calculated and stored.
automatically obtained when teach The screen then returns to “MANUAL>SHIFT” mode.
point 1 is determined. The Z-axis data
at teach point 2 is therefore ignored.
Valid keys and submenu descriptions in “MANUAL>SHIFT>METHOD1” mode are
shown below.
Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
(100→50→20→5→1 %)
4-112
11. “MANUAL” mode
Point 1
(1st P)
n When
NOTE
two robots (main and sub
robots) are specified, check the
currently selected robot group on the
MPB screen.
4
“[MG]” indicates the main robot
Operation
group is selected, and “[SG]”
indicates the sub robot group is
selected. To change the robot group,
use the ROBOT ( LOWER + MODE ) key.
Point 2
(2nd P)
X' Y Y'
[Procedure]
1) In “MANUAL>SHIFT” mode, select the shift coordinate number with the cursor
(↑/↓) key.
n Perform
NOTE
teaching carefully to obtain
accurate teach points. Precise shift
coordinates cannot be set if the teach
point is inaccurate.
4-113
11. “MANUAL” mode
7) When the teach point 2 has been entered, the shift coordinates (dX, dY, dZ and dR)
n NOTE
The Z-direction shift value is automati-
are automatically calculated and stored.
cally obtained when teach point 1 is
The screen then returns to “MANUAL>SHIFT” mode.
determined, so the Z-axis data at teach
point 2 is ignored. Valid keys and submenu descriptions in “MANUAL>SHIFT>METHOD2” mode are
shown below.
Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
(100→50→20→5→1 %)
4-114
11. “MANUAL” mode
Operation
1st parameter ................ ±aaaaaa
Enter a number consisting of an integer portion of up to
5 digits and having 2 or less places below the decimal
point, or an integer of up to 7 digits (depending on the
robot type setting and hand definition type).
2nd to 3rd parameters .. ±bbbbbb, ±cccccc
Enter a number consisting of an integer portion of up to
5 digits and having 2 or less places below the decimal
point.
4th parameter ............... R
Enter one character (depending on the hand definition
type).
When all values for a hand definition are “0”, this means the hand definition is not set.
n Hand
NOTE
definition data cannot be used On entering “MANUAL>HAND” mode, a screen like that shown in Fig. 4-11-65, Fig. 4-
with MULTI type robots since the 11-66 or Fig. 4-11-67 appears.
SHIFT/HAND selection display on the
1st line on the MPB screen appears The currently selected hand definition number is highlighted.
blank.
Fig. 4-11-65 Hand definition screen (one-robot setting)
4-115
11. “MANUAL” mode
————————————1———————2———————3———————4———
H4 = 0 0.00 0.00
H5 = 0.00 100.00 0.00 R
H6 = 90.00 100.00 100.00 R
H7 = 8000 100.00 100.00
[POS] 600.00 0.00 0.00 0.00
EDIT VEL+ VEL-
Valid keys and submenu descriptions in “MANUAL>HAND” mode are shown below.
Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
(100→50→20→5→1 %)
ROBOT
( LOWER Switches the robot group.
+ MODE )
4-116
11. “MANUAL” mode
Movement of each robot type and the parameter contents are shown below.
Operation
arm length. (unit: mm)
<3rd parameter>: Specify the Z-axis offset amount of hand “n” with a real number.
(unit: mm)
<4th parameter>: No setting for “R”.
Fig. 4-11-68
HAND 1
HAND 0
20.00mm
-5000 pulse
m
0m
0.0
15
rm
da
2n
ard
nd
Sta
4-117
11. “MANUAL” mode
b. Parameter descriptions
<1st parameter>: When the current R-axis position is 0.00, specify with a real
number the angle between the +X direction of Cartesian
coordinates and hand “n”. If counterclockwise, enter a “+” value.
(unit: degrees)
<2nd parameter>: Specify the length of hand “n” with a positive real number. (unit:
mm)
<3rd parameter>: Specify the Z-axis offset amount of hand “n” with a real number.
4 (unit: mm)
<4th parameter>: Specify “R”.
Operation
Fig. 4-11-70
HAND 0
-90.00 degrees
100.00mm
HAND 1
4-118
11. “MANUAL” mode
Fig. 4-11-72 4
Operation
X
HAND 1
-100.00mm
HAND 0
-100.00mm
4-119
11. “MANUAL” mode
b. Parameter descriptions
<1st parameter>: When the current R-axis position is 0.00, specify with a real
number the angle between the +X direction of Cartesian
coordinates and hand “n”. If counterclockwise, enter a “+” value.
(unit: degrees)
<2nd parameter>: Specify the length of hand “n” with a positive real number. (unit:
mm)
<3rd parameter>: Specify the Z-axis offset amount of hand “n” with a real number.
4 (unit: mm)
<4th parameter>: Specify “R”.
Operation
Fig. 4-11-74
HAND 1
HAND 0
100.00mm
4-120
11. “MANUAL” mode
2) Use the cursor (↑/↓) keys to select the hand definition you want to edit.
An edit cursor appears at the left end of the selected hand definition line.
Operation
UNDO
3) Use the cursor (←/→) key to move the cursor to the position you want to edit.
5) Pressing the key or cursor up/down (↑/↓) keys completes the hand definition
settings.
Press the ESC key if you want to cancel the settings.
n The
NOTE
hand definition data with which
6) To continue editing, repeat steps 2) to 4).
4-121
11. “MANUAL” mode
[Procedure]
1) During hand definition editing, pressing the F 1 (UNDO) key reverses the last
data input and restores the preceding data.
This function is enabled only on lines that are not yet complete.
4-122
11. “MANUAL” mode
w The
WARNING
robot starts to move when a
3) Use the Jog keys to move the robot working point to point 1.
(Position it accurately.)
Jog key is pressed. To avoid
danger, do not enter the robot
movement range.
4) Press the key to enter the teaching value.
Operation
n NOTE
• When teach point 1 is obtained,
(Position it accurately.)
Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
(100→50→20→5→1 %)
4-123
11. “MANUAL” mode
2) Each time the key is pressed, the units displayed on the upper right of the MPB
screen are switched to “X” or “J” or "T". However, "T" (Tool coordinate mode) can
be selected only when hand data for the R-axis is selected (hand definition is made),
Robot manual movement with Jog keys differs depending on the currently selected display
units. For more details, refer to "11.1 Manual movement" in this chapter.
4-124
11. “MANUAL” mode
c Emergency
CAUTION
stop may occur if absolute
a. An absolute-related error occurred on the axis.
17.73:D?.Resolver wire breakage
reset at the stroke end is performed 17.91:D?.Cannot perform ABS.reset
for two or more axes simultaneously. etc.
In this case, perform return-to-origin
separately for each axis separately b. Absolute battery wire breakage or voltage drop was detected by the controller.
instead of simultaneously. c. Cable connecting to the robot unit from the robot Controller was disconnected. (This
is the status when shipped from the factory.)
d. Robot generation was changed. 4
n NOTE
• Basically, use the MPB (teaching
e. Parameters were initialized.
Operation
pendant) to perform absolute f. Axis-related parameters such as “Origin shift”, “Origin detection method” and “Origin
reset. return direction” and “Axis polarity” were changed. (This occurs when some parameters
• Absolute reset can also be
performed by dedicated input.
were changed.)
However, this technique is limited g. Motor was replaced.
to axes using the stroke end
method or sensor method for h. All data files (data file with extension “ALL”) or parameter files (data files with
detecting the origin. This extension “PRM”) were written into the robot controller.
dedicated input technique will also
not work if origin incomplete
occurs on axes set by the mark Origin incomplete errors are listed below. These errors occur during startup of the robot
method. controller.
4-125
11. “MANUAL” mode
Fig. 4-11-81
4 M2 = NG / Sensor
M3 = NG / TORQUE
M6= no axis
M4 = OK / Sensor
M1 M2 M3 M4 M5
Operation
No axis hereafter
The above MPB screen shows the return-to-origin is incomplete on axis 1, axis 2 and axis
3 but complete on axis 4. The robot controller is in origin incomplete status, since not all
axes performed return-to-origin.
* Valid key menus differ depending on the sub robot or auxiliary axis settings.
4-126
11. “MANUAL” mode
n When
NOTE
the mark method is used as the
11.8.2 Absolute reset on each axis
origin detection method, absolute reset This section explains how to perform absolute reset of each axis using the robot controller.
is impossible unless the machine The absolute reset method differs depending on the following settings for the “Origin
reference is between 44 to 56%. detection method” parameter.
1. Mark method
2. Stroke end or sensor method
1. When the mark method is used as the origin detection method
w The robot starts to move when a
WARNING Return-to-origin is not performed on an axis using the mark method. So use the
movement keys while in servo-on, or direct movement while in servo-off, to move to
movement key is pressed. To
avoid danger, do not enter the a position where absolute reset can be performed.
robot movement range.
Valid keys Menu Function
Moves the selected axis in the plus direction to the first position
F1 ADJ+
where absolute reset is possible. 4
Moves the selected axis in the minus direction to the first position
F2 ADJ-
where absolute reset is possible.
Operation
Increases manual movement speed for the selected robot group in steps.
F4 VEL+
(1→5→20→50→100 %)
Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
(100→50→20→5→1 %)
Fig. 4-11-82
0 25 50 75 0 25 50 75 0
4-127
11. “MANUAL” mode
w The
WARNING
robot starts to move slightly
Absolute reset position and "0" pulse position
when absolute reset is When absolute reset is performed at position A, position B (machine reference 38%) is
performed while the servo is on. reset as the "0" pulse position. This means that the robot will move to the "0" pulse
To avoid danger, do not enter the position after performing absolute reset with the servo turned on.
robot movement range.
Fig. 4-11-83
0 25 50 75 0
4 [Procedure]
: Range in which absolute reset can be made (44 to 56%).
Operation
Fig. 4-11-84
Fig. 4-11-85
4-128
11. “MANUAL” mode
w The
WARNING
robot starts to move when a
2) In Servo-ON
Jog key or movement key is Use the Jog keys or F 1 (ADJ.+) and F 2 (ADJ.-) keys to move the selected
pressed. To avoid danger, do not axis to a position where absolute reset is possible. Set so that the machine reference
enter the robot movement range. is within a range of 44 to 56%.
Fig. 4-11-86
Operation
w When
WARNING
you perform direct
In Servo-OFF
Check that the emergency stop button on the MPB is on, and move the selected axis
teaching, make sure that the
emergency stop button is by direct movement to a position for absolute reset. Set so that the machine reference
pressed so that the servo will is within a range of 44 to 56%.
not turn on.
Fig. 4-11-87
c AnCAUTION
error message, "17.91:D?.Cannot
3) Press the key and a confirmation message appears on the guideline.
perform ABS.reset" appears if the Press the F 4 (YES) key to perform absolute reset of the selected axis.
machine reference is not within a
range of 44 to 56%. The absolute Press the F 5 (NO) key to cancel absolute reset of the selected axis.
reset operation then terminates as an
error. Fig. 4-11-88
If the robot controller is in origin
incomplete due to some kind of
MANUAL >RST.ABS>M1 50% [MG] [SOHOJ]
problem perform absolute reset on the
axis which was unable to return to ––––––––––––––––––––––––––––––––––––––––
origin. After absolute reset, always Align axes with MARK,& Press ENTER
check if the axis can move to the same
position as before origin incomplete. M1 = NG / 50% M5= no axis
M2 = NG / 49% M6= no axis
M3 = NG / TORQUE
M4 = OK / 72%
Reset ABS OK? YES NO
4-129
11. “MANUAL” mode
w The
WARNING
robot starts to move slightly
4) If the servo is on when performing absolute reset, the robot will move to the "0" pulse
position after reset.
when absolute reset is
performed while the servo is on.
To avoid danger, do not enter the 5) When all axes have returned to origin, the dashed line (- - - -) on the message line
robot movement range. changes to a solid line (——), and return-to-origin is now complete. Next, press an
axis movement key and the MPB screen will display the current position of each axis.
6) When origin incomplete status cannot be canceled, this means an axis has still not
returned to origin. So repeat the absolute reset operation.
4
Operation
4-130
11. “MANUAL” mode
2. When the stroke end or sensor method is used as the origin detection
method
When the selected axis uses the stroke end or sensor method, the servo must be turned
on to perform return-to-origin.
[Procedure]
1) In “MANUAL>RST. ABS” mode, press the F 1 (M1) to F 4 (M4) keys to
w The
WARNING
robot starts to move when
enter “MANUAL>RST.ABS” mode on each axis. A confirmation message appears
on the guideline.
absolute reset is performed. To
avoid danger, do not enter the Press the F 4 (YES) key to perform absolute reset of the selected axis.
robot movement range.
Press the F 5 (NO) key to cancel absolute reset of the selected axis.
Fig. 4-11-89
4
MANUAL >RST.ABS>M3 50% [MG] [SOHOJ]
––––––––––––––––––––––––––––––––––––––––
Operation
n When
NOTE
the "Origin detection method"
Starting origin search
M1 M2 M3 M4 M5
3) When all axes have returned to origin, the dashed line (- - - -) on the message line
changes to a solid line (——), and return-to-origin is now complete. Then, press an
axis movement key and the MPB screen displays the current position of each axis.
4) To cancel the return-to-origin operation, press the STOP key. In this case, the
message “Origin Incomplete” then appears on the message line.
4-131
11. “MANUAL” mode
Moves the selected axis in the plus direction to the first position
F1 ADJ.+
where absolute reset is possible.
4 F2 ADJ.-
Moves the selected axis in the minus direction to the first position
where absolute reset is possible.
Operation
Increases manual movement speed for the selected robot group in steps.
F4 VEL+
(1→5→20→50→100 %)
Decreases manual movement speed for the selected robot group in steps.
F5 VEL-
(100→50→20→5→1 %)
Fig. 4-11-91
e q w
0 25 50 75 0 25 50 75 0
4-132
11. “MANUAL” mode
w The
WARNING
robot starts to move when
Absolute reset position and "0" pulse position
absolute reset is performed. To When absolute reset is performed at position A, the position B (machine reference 38%)
avoid danger, do not enter the is reset as the "0" pulse position. This means that the robot will move to the "0" pulse
robot movement range. position after performing absolute reset with the servo turned on.
Fig. 4-11-92
0 25 50 75 0
[Procedure]
: Range in which absolute reset can be made (44 to 56%).
4
Operation
Fig. 4-11-93
Fig. 4-11-94
n When
NOTE
the mark method is used as the
Axis 1 Origin incomplete 6
Axis 2 Origin incomplete 49
origin detection method, absolute reset
is impossible unless the machine Axis 3 Origin incomplete Stroke end method
reference is between 44 to 56%.
Axis 4 Return to origin complete 72
No axis hereafter
4-133
11. “MANUAL” mode
w The
WARNING
robot starts to move when a
2) The axis using the mark method appears highlighted on the LCD screen.
Use the cursor (↑/↓) keys to select the axis.
Jog key or movement key is
pressed. To avoid danger, do not Use the Jog keys or the F 1 (ADJ.+) and F 2 (ADJ.-) keys to move the
enter the robot movement range.
selected axis to a position for performing absolute reset. Set at this time so that the
machine reference is between 44 to 56%.
Fig. 4-11-95
w The
WARNING
robot starts to move when
3) Press the key and a confirmation message appears on the guideline.
Fig. 4-11-96
n AnNOTE
error message, "17.91:D?.Cannot
MANUAL >RST.ABS>ALL 50% [MG] [SOHOJ]
perform ABS.reset" appears if the ––––––––––––––––––––––––––––––––––––––––
machine reference is not within a Align axes with MARK,& Press ENTER
range of 44 to 56%. Absolute reset
M1 = NG / 50% M5= no axis
operation then terminates as an error.
If the robot controller is in origin M2 = NG / 49% M6= no axis
incomplete due to some kind of M3 = NG / TORQUE
problems, perform absolute reset on
the axis which was unable to return to M4 = OK / 72%
origin. After absolute reset, always Reset ABS OK? YES NO
check if the axis can move to the same
position as before origin incomplete. 4) If the servo is on when performing absolute reset on all axes that use the mark
method, the robot will move to the "0" pulse position after reset.
4-134
11. “MANUAL” mode
5) When absolute reset ends correctly on all axes using the mark method, a
confirmation message appears on the guideline if axes using the stroke end or
sensor methods are present.
Press the F 4 (YES) key to perform absolute reset on axes using the stroke end
or sensor method.
Press the F 5 (NO) key to cancel absolute reset on axes using the stroke end or
sensor method.
Fig. 4-11-97
Operation
Reset ABS OK? YES NO
6) After return-to-origin is complete, the machine reference for axes using the stroke
end or sensor method is displayed.
Fig. 4-11-98
c IfCAUTION
the robot controller is in origin
MANUAL >RST.ABS 50% [MG] [SOHOJ]
––––––––––––––––––––––––––––––––––––––––
incomplete due to some kind of
problems, perform absolute reset on Machine Reference (%)
the axis which was unable to return to M3 = 49
origin. After absolute reset, always
check if the axis can move to the same
position as before origin incomplete.
M1 M2 M3 M4 M5
7) When absolute reset of all axes ends correctly, the dashed line (- - - -)on the
message line changes to a solid line (––––), and return-to-origin is now complete.
Next press an axis movement key and the MPB screen will display the current
c IfCAUTION
absolute reset does not end
position of each axis.
correctly after performing absolute
reset on all axes, check the return-to-
origin status on each axis. Then try 8) To cancel return-to-origin operation, press the STOP key. In this case, the message
absolute reset on all axes once again "Origin Incomplete" then appears on the message line.
or try absolute reset on each
individual axis until you can
successfully set the return-to-origin.
4-135
11. “MANUAL” mode
This method sets the standard coordinates by using 3 teach points (equally spaced) on
a straight line. The direction and length from the first teach point to the last teach point
must be entered.
• Simple teaching
This method sets the standard coordinates by moving the X and Y arms so as to set
them in a straight line and then entering the length of the X and Y arms.
Fig. 4-11-99
L L
P[3] P[4]
P[1] P[2]
4-136
11. “MANUAL” mode
c When
CAUTION
setting the standard
The following parameters are automatically set when the standard coordinates are entered.
Operation
When two robots (main and sub robots) are specified, the following parameters are also
entered automatically for the sub robot.
2) “Offset pulse”
S1= ###### ....... X-axis offset pulse (angle formed by the X-axis when the robot is at
the origin (0 pulse) position and the X-axis on the standard coordinate
plane)
S2= ###### ....... Y-axis offset pulse (angle formed by the X-axis and Y-axis when the
robot is at the origin (0 pulse) position)
S4= ###### ....... R-axis offset pulse (angle formed by the R-axis when the robot is at
the origin (0 pulse) position and the X-axis on the standard coordinate
plane)
4-137
11. “MANUAL” mode
Fig. 4-11-100
4
c When
CAUTION
Y
Operation
n NOTE
• Approximate standard coordinate MANUAL>COORDI 50% [MG][ J]
settings are made prior to
————————————x———————y———————z———————r———
shipment.
• The number of offset pulses equals How many points method are used?
the number of pulses used by the F1:4 points teach method
X, Y and R axes when they moved
F2:3 points teach method
towards the X-axis on the standard
coordinates.
F5:Simple method
Valid keys and submenu descriptions in “MANUAL” mode are as shown below.
4-138
11. “MANUAL” mode
Fig. 4-11-102
n NOTE
P[3] P[4]
• Separate the teach points from
each other as much as possible.
• Setting might be impossible if one
side is less than 50mm.
P[1] P[2]
Operation
4-point teaching
Precondition: Coordinate values made for P[2], P[3], P[4] must be accurate when P[1] is
set as the origin position.
[Procedure]
1) In “MANUAL>COORDI” mode, press the F 1 (4POINTS) key to enter the mode
for setting standard coordinates by 4-point teaching.
Fig. 4-11-103
4-139
11. “MANUAL” mode
n Standard
NOTE
coordinates are calculated
2) Use the Jog keys to move the robot arm tip to teach point P[1] and press the key.
based on the teach points and input
point data, so perform teaching and
point data input as accurately as 3) Perform teaching at point P[2] as in step 2).
possible.
4) Enter the position of teach point P[2] in millimeters, relative to P[1] set as the origin.
Fig. 4-11-104
4 P[4]=
[POS] 0 0 0 0
VEL+ VEL-
Operation
6) A message for checking the length and offset pulse value appears on the guideline.
(If the calculation failed, an error message appears.)
Press the F 4 (YES) key to store the setting.
Press the F 5 (NO) key if you want to cancel the setting.
Fig. 4-11-105
4-140
11. “MANUAL” mode
n Separate
NOTE
the teach points from each
11.9.2 Setting the standard coordinate by 3-point teaching
other as much as possible.
Fig. 4-11-106
L L
Operation
Precondition: All 3 points P[1], P[2] and P[3] must be on a straight line, with P[2] set at
the midpoint between P[1] and P[3].
[Procedure]
1) In “MANUAL>COORDI” mode, press the F 2 (3POINTS) key to enter the
mode for setting standard coordinates with 3-point teaching.
Fig. 4-11-107
2) Use the Jog keys to move the robot arm tip to teach point P[1] and press the
n Standard
NOTE
coordinates are calculated key.
based on the teach points and input
point data, so perform teaching and Fig. 4-11-108
point data input as accurately as
possible.
MANUAL>COORDI>3POINTS 50% [MG][ J]
————————————x———————y———————z———————r———
Move arm to P[2] and press ENTER key
P[1]= -43202 47158
P[2]=
P[3]=
[POS] -43202 47158 0 0
VEL+ VEL-
4-141
11. “MANUAL” mode
4) Use the F 1 (+X) to F 4 (-Y) keys to set the direction from P[1] to P[3].
Fig. 4-11-109
4 +X -X +Y -Y
5) Use the 0 to 9 , . keys to enter the length between P[1] and P[3],
Operation
Fig. 4-11-110
6) A message for checking the arm length and offset pulse value appears on the
guideline. (If the calculation failed, an error message appears.)
Press the F 4 (YES) key to store the setting.
Press the F 5 (NO) key if you want to cancel the setting.
Fig. 4-11-111
Arm length[mm]
M1= 199.96 M2= 199.98
Offset pulse
M1= -12421 M2= 2001
4-142
11. “MANUAL” mode
n Position
NOTE
the XY arms as accurately as
11.9.3 Setting the standard coordinates by simple teaching
possible, so that they are exactly set in
Fig. 4-11-112
a straight line including the rotation
center of the R-axis. +Y direction
+X direction
[Procedure]
1) In “MANUAL>COODI” mode, press the F 5 (SIMPLE) key to enter the mode for
simple standard coordinate setting.
Fig. 4-11-113 4
MANUAL >COORDI>SIMPLE 50% [MG][ J]
Operation
————————————x———————y———————z———————r———
Please Move X & Y arms straight
before press Enter key.
X Arm Y Arm
0=======0======[ —> +X
[POS] 24349 -1029 0 0
VEL+ VEL-
2) Use the Jog keys or your hands (if the servo is off) to move the robot arm so that the
X and Y arms are set in a straight line, then press the key.
At this point, the +X direction is set as shown in Fig. 4-11-103.
Fig. 4-11-114
4-143
11. “MANUAL” mode
Fig. 4-11-115
5) A message for checking the arm length and offset pulse value appears on the
4 guideline.
Press the F 4 (YES) key if you want to store the setting.
Operation
Fig. 4-11-116
4-144
11. “MANUAL” mode
n NOTE
• When using the user function keys,
11.10 Executing the user function keys
it is necessary to make a program User function keys allow you to perform various tasks easily when needed. For example,
named “FUNCTION” and then
write command statements for
assigning operation of an air-driven unit connected to an output port to a function key will
storing functions. prove useful when performing point teaching in “MANUAL” mode.
• When registering the function
keys, refer to "10.3.9 Creating a
[Procedure]
sample program automatically” 1) Press the USER key in “MANUAL” mode and the menus (character strings shown
and "10.6 Registering user
function keys” earlier in this highlighted) from F 1 to F 15 or F 16 to F 30 appear when assigned in
chapter.
advance.
Each character string is displayed in up to 7 characters from the beginning.
w WARNING
• The robot starts to move 2) Press the desired function key and the preassigned task will be executed just as if
when some commands are using online commands.
executed. To avoid danger,
do not enter the robot
Fig. 4-11-117
4
movement range.
• Robot movement commands
Operation
are executed at “AUTO” MANUAL>POINT 50%[MG][S0H0X]
mode speed rather than ————————————x———————y———————z———————r———
“MANUAL” mode speed.
P7 = 100.00 250.00 15.00 30.00
P8 =
P9 = 122.62 -24.54 12.35 -23.11
COMNT: [ ]
[POS] 0.00 0.00 0.00 0.00
1 DO(20)A DO(21)A DO(22)A DO(23)A DO(24)A
4-145
12. “SYSTEM” mode
The “SYSTEM” mode controls all kinds of operating conditions for the overall robot system.
e Message line
q Mode hierarchy
r Online command w Version display
execution mark
4 i Other
expanded
Opt-i/f = DIO_N(1/2)
configurations
PARAM CMU OPTION INIT DIAGNOS
Operation
o Guideline
q Mode hierarchy
Shows the current mode hierarchy. When the highest mode (in this case “SYSTEM”)
is highlighted it means the servomotor power is on. When not highlighted it means the
servomotor power is off.
w Version display
Shows the version number of software currently installed in the robot controller.
e Message line
If an error occurs, the error message appears here.
r Online command execution mark
When an online command is being executed, a “@” mark appears in the second col-
umn on the second line. This mark changes to a dot ( . ) when the online command
ends.
t Robot model name
Shows the robot model name specified by the controller.
When two robots (main robot and sub robot) are specified, their model names appear
separated by a slash ( / ).
y Axis configuration
Shows the axis configuration of the robot connected to the controller.
When two robots (main robot and sub robot) are specified, their axis configurations
appear separated by a slash ( / ). If an auxiliary axis is added, it also appears preceded
by a plus mark (+).
u Standard system configuration
c CAUTION
• See "7. I/O connections" in Shows the memory type and size and standard DIO type.
Chapter 3 for a definition of NPN
and PNP specifications.
• For detailed information about Display Meaning
serial I/O units such as CC-Link
units, refer to descriptions in DIO_N Standard DIO works on NPN specifications.
their OWNER'S MANUAL. DIO_P Standard DIO works on PNP specifications.
4-146
12. “SYSTEM” mode
Display Meaning
An optional DIO with NPN specifications is installed. The number in
DIO_N(m/n..)
parentheses is an ID number.
An optional DIO with PNP specifications is installed. The number in
DIO_P(i/j..)
parentheses is an ID number.
A CC-Link unit is installed. The number in parentheses indicates a
CCLNK(n/m)
station number "n" and a communication speed "m".
A DeviceNet unit is installed. The number in parentheses indicates a
D_Net(n/m)
MAC ID number "n" and a communication speed "m".
A ProfiBUS unit is installed. Letters in parentheses indicate a Station
Profi(n/m) address "n" and communication speed "m".
c For
CAUTION
details on service mode setting,
E_Net An Ethernet unit is installed. 4
refer to "12.3.2 Setting the
“SERVICE” mode". When set to SAFE mode, the following display appears.
Operation
Display Meaning
safemode Operation mode is set to SAFE mode that enables service mode.
o Guideline
The contents assigned to function keys are shown highlighted. A message on what to
do next also appears here in some operation steps.
Valid keys and submenu descriptions in “SYSTEM” mode are shown below.
4-147
12. “SYSTEM” mode
12.1 Parameters
This section explains various parameters relating to the controller setting and robot op-
eration.
There are 4 types of parameters: robot parameters and axis parameters for robot operation,
controller setting parameters and option board parameters.
[Procedure]
1) Press the F 1 (PARAM) key in “SYSTEM” mode to enter “SYSTEM>PARAM”
mode.
SYSTEM>PARAM V8.35
Robot = TXYx-A
M1= aTx-T6-12 M5= no axis
M2= aTy-T6-12 M6= no axis
M3= aZF-F10-10V
M4= aRF
ROBOT AXIS OTHERS OP.BRD
1.Tip weight[kg]
2.Origin sequence
3.R axis orientation
4.Armtype at PGM reset
EDIT JUMP
4-148
12. “SYSTEM” mode
Valid keys and submenu descriptions in “SUSTEM>PARAM” mode are shown below.
Operation
4-149
12. “SYSTEM” mode
SYSTEM>PARAM>ROBOT V8.35
1.Tip weight[kg]
4 MR= 5
Operation
[0-200] Enter>5
_
SYSTEM>PARAM>ROBOT V8.35
1.Tip weight[kg]
MR= 5
SR= 4
5
[0-200] Enter>_
Valid keys and submenu descriptions for editing robot parameters are shown below.
( / )
F1 EDIT Edits the parameter.
F2 JUMP Moves the cursor to the designated parameter.
4-150
12. “SYSTEM” mode
Operation
axis parameters. SYSTEM>PARAM>ROBOT V8.35
1.Tip weight[kg]
MR= 5
c Factors
CAUTION
such as optimal speed are set
5
[0-200] Enter>_
4-151
12. “SYSTEM” mode
2.Origin sequence
MG= 312456
c IfCAUTION
stroke-end return-to-origin is
simultaneously performed on two or
more axes, then emergency stop might
312456
[0-654321] Enter>_
be triggered and an error message
issued. This may harm the robot body
so do not perform stroke end return- 4) Enter the value with the 0 to 9 keys and then press the key.
to-origin simultaneously on more
than 1 axis.
4-152
12. “SYSTEM” mode
n This
NOTE
parameter is valid only on SCARA
[Procedure]
1) Select “3.R axis orientation” in “SYSTEM>PARAM>ROBOT” mode.
robots.
Operation
SYSTEM>PARAM>ROBOT V8.35
KEEP FREE
n This
NOTE
function is invalid if there is no R-
4) Press the F 1 (KEEP) key or the F 2 (FREE) key.
4-153
12. “SYSTEM” mode
SYSTEM>PARAM>ROBOT V8.35
RIGHTY LEFTY
4) Press the F 1 (RIGHTY) key or the F 2 (LEFTY) key to select the hand sys-
tem.
4-154
12. “SYSTEM” mode
SYSTEM>PARAM>AXIS V8.35
1.Accel coefficient[%]
M1= 100 M2= 100 M3= 100
m4= 100
4
Operation
100
[1-100] Enter>_
SYSTEM>PARAM>AXIS V8.35
n ANOTE
description and method for setting
1.Accel coefficient[%]
M1= 100 M2= 100
axis parameters No. 1 through No. 16 .
are listed in this manual.
Changing of parameters from No. 17 S1= 100 S2= 100
onward is basically prohibited. Please
consult with us beforehand if these
(parameter No. 17 onward) must be [1-100] Enter>_
100
changed.
Valid keys and submenu descriptions for editing robot parameters are shown below.
( / )
F1 EDIT Edits the parameter.
F2 JUMP Moves the cursor to the designated parameter.
4-155
12. “SYSTEM” mode
SYSTEM>PARAM>AXIS V8.35
1.Accel coefficient[%]
M1= 100 M2= 100 M3= 100
n IfNOTE
the robot arm tip shakes or sways
m4= 100
c Lowering
CAUTION
the acceleration coefficient
4) Enter the value with the 0 to 9 keys and then press the key.
4-156
12. “SYSTEM” mode
n This
NOTE
parameter value is a ratio to the
This parameter sets the deceleration rate in a range from 1 to 100% during movement
by robot movement command. This parameter value is a ratio to the acceleration. A
acceleration. deceleration rate inherent to each axis is automatically set when the parameters are
initialized.
[Procedure]
1) Select “2. Decel. rate [%]” in “SYSTEM>PARAM>AXIS” mode.
Operation
2.Decel. rate[%]
n IfNOTE
the robot arm tip shakes or sways
M1=
m4=
100
100
M2= 100 M3= 90
100
[1-100] Enter >_
c Lowering
CAUTION
the deceleration ratio
4) Enter the value with the 0 to 9 keys and then press the key.
4-157
12. “SYSTEM” mode
SYSTEM>PARAM>AXIS V8.35
c CAUTION
• This is a critical parameter for [+/-6144000] Enter >_
100000
establishing the robot operating
range so set it to a correct value.
• On SCARA robots, make sure that 4) Enter the value with 0 to 9 , and . , – keys and then press the
the total movement range of the
“+” and “-” software limits for X- key. If the value you input was a real number (number containing a decimal point),
axis and Y-axis does not exceed
then the soft limit setting is converted into “pulse” units.
360 degrees. If the setting exceeds
360 degrees, then errors might
occur in the coordinate conversion
results.
5) Repeat the above steps 3) and 4) if necessary.
• Software limits are disabled when
origin return is incomplete.
Use caution during jog movement. 6) Press the ESC key to quit the edit mode.
4-158
12. “SYSTEM” mode
Fig. 4-12-15
Tolerance range 4
Operation
[Procedure]
1) Select “5. Tolerance [pulse]” in “SYSTEM>PARAM>AXIS” mode.
SYSTEM>PARAM>AXIS V8.35
4.Tolerance[pulse] ( 0. 09mm)
M1= 80 M2= 80 M3= 80
m4= 80
c CAUTION
• This is a critical parameter for
determining the robot movement [1- 80
] Enter >_
neat the target position so set it to
a correct value.
• If the tolerance range was 4) Enter the value with the 0 to 9 , and . keys and then press the
reduced to a drastically small key. If the value you input was a real number (number containing a decimal point),
value then return-to-origin might
then the tolerance range is converted into “pulse” units.
not end correctly. The time
needed for robot positioning
might also be irregular.
• The maximum tolerance value is
5) Repeat the above steps 3) and 4) if necessary.
determined by the motor.
4-159
12. “SYSTEM” mode
Out position
Operation
range
Tolerance range
[Procedure]
1) Select “6. Out position [pulse]” in “SYSTEM>PARAM>AXIS” mode.
SYSTEM>PARAM>AXIS V8.35
2000
[1-6144000] Enter >_
c When
CAUTION
the tolerance range is larger
4) Enter the value with the 0 to 9 , and . keys and then press the
key. If the value you input was a real number (number containing a decimal point),
than the Out position range, the PTP
then it is converted into pulse units.
operation is performed until the robot
is within the Out position range.
5) Repeat the above steps 3) and 4) if necessary.
4-160
12. “SYSTEM” mode
Operation
of other axes
Movement of other axes
[Procedure]
1) Select “7. Arch position [pulse]” in “SYSTEM>PARAM>AXIS” mode.
SYSTEM>PARAM>AXIS V8.35
2000
[1-6144000] Enter >_
c CAUTION
• The arch-specified axis may 4) Enter the value with the 0 to 9 , and . keys and then press the
sometimes reach the target key. If the value you input was a real number (number containing a decimal point),
position faster than the other
axes if the arch position is large. then it is converted into pulse units.
So set an accurate value for the
arch position.
• Movement may be along different 5) Repeat the above steps 3) and 4) if necessary.
paths during arch operation due
to the movement speed. Check the
arch motion at a speed at which 6) Press the ESC key to quit the edit mode.
the robot actually moves.
4-161
12. “SYSTEM” mode
4 SYSTEM>PARAM>AXIS V8.35
8.Origin speed[pulse/ms]
Operation
20
[1- ] Enter >_
4) Enter the value with the 0 to 9 keys and then press the key.
c The
CAUTION
maximum return-to-origin speed 5) Repeat the above steps 3) and 4) if necessary.
is determined by the motor.
4-162
12. “SYSTEM” mode
Operation
SYSTEM>PARAM>AXIS V8.35
n IfNOTE
the robot arm tip shakes or sways 9.Manual accel[%]
during manual movement acceleration, M1= 100 M2= 100 M3= 100
lower this value to suppress the
shaking. 100m4= 100
100
[1-100] Enter >_
4) Input the value with the to keys and then press the key.
c Lowering
0 9
CAUTION
the acceleration coefficient
lengthens the time needed to stop,
when the STOP key was pressed or an 5) Repeat the above steps 3) and 4) if necessary.
interlock was triggered. Do not use a
drastically lowered acceleration
coefficient. 6) Press the ESC key to quit the edit mode.
4-163
12. “SYSTEM” mode
SYSTEM>PARAM>AXIS V8.35
10.Origin shift[pulse]
M1= 0 M2= 0 M3= 0
m4= 0
c CAUTION
• Origin shift is a critical 4) Enter the value with the 0 to 9 , – keys and then press the key.
parameter for determining the
robot position so set it to a correct
value. Change this parameter
only when necessary.
5) Repeat the above steps 3) and 4) if necessary.
• Origin return will be incomplete
if this parameter is changed.
• This parameter is enabled after 6) Press the ESC key to quit the edit mode.
absolute reset.
4-164
12. “SYSTEM” mode
Operation
SYSTEM>PARAM>AXIS V8.35
11.Arm length[mm]
M1= 200.00 M2= 200.00 M3= 0.00
m4= 0.00
200.00
[0-10000] Enter >_
c OnCAUTION
SCARA robots, the arm length
4) Enter the value with the 0 to 9 , and . keys and then press the
key.
and offset pulses are used to change
coordinates to the Cartesian
coordinate system. Make sure the arm 5) Repeat the above steps 3) and 4) if necessary.
length setting is accurate so the
Cartesian coordinates can be used
effectively and with high precision.
6) Press the ESC key to quit the edit mode.
4-165
12. “SYSTEM” mode
SYSTEM>PARAM>AXIS V8.35
11.Offset pulse
M1= 10000 M2= 20000 M3= 0
c CAUTION
• On SCARA robots, the arm m4= 1000
length and offset pulses are used
to change coordinates to the
Cartesian coordinate system.
Make sure the arm length setting 10000
[+/-6144000] Enter >_
is accurate so the Cartesian
coordinates can be used
4) Enter the value with the 0 to 9 keys and then press the key.
effectively and with high
precision.
• When some value (including 0)
has been entered for this 5) Repeat the above steps 3) and 4) if necessary.
parameter, it means the settings
are in standard coordinates.
6) Press the ESC key to quit the edit mode.
4-166
12. “SYSTEM” mode
Operation
n NOTE
• This parameter can be entered
SYSTEM>PARAM>AXIS V8.35
0
[0-200] Enter >_
c Optimal
CAUTION
acceleration and other items 4) Enter the value with the 0 to 9 keys and then press the key.
are automatically set according to this
parameter value. The robot body may
therefore be adversely affected if set
to a lower value than the actual axis
5) Repeat the above steps 3) and 4) if necessary.
tip weight, so be sure to enter a
correct value.
6) Press the ESC key to quit the edit mode.
4-167
12. “SYSTEM” mode
SYSTEM>PARAM>AXIS V8.35
14.Origin method
M1=SENSOR M2=SENSOR M3=TORQUE
M4=MARK
c CAUTION
• YAMAHA can accept no liability
from problems arising due to SENSOR TORQUE MARK
changing the return-to-origin
method without consulting 4) Press one of the F 1 (SENSOR), F 2 (TORQUE) or F 3 (MARK) keys.
YAMAHA beforehand.
• Return-to-origin will be
incomplete if this parameter is
changed. 5) Repeat the above steps 3) and 4) if necessary.
• Use the “sensor” method or
“mark” method for performing
return-to-origin on rotating axes. 6) Press the ESC key to quit the edit mode.
4-168
12. “SYSTEM” mode
Operation
15.Origin direction
M1=––– M2=––– M3=+++
m4=–––
––– +++
c CAUTION
• YAMAHA can accept no liability 4) Press the F 1 (---) or F 2 (+++) key.
from problems arising due to
changing the return-to-origin
direction without consulting 5) Repeat the above steps 3) and 4) if necessary.
YAMAHA beforehand.
• Return-to-origin will be
incomplete if this parameter is
6) Press the ESC key to quit the edit mode.
changed.
4-169
12. “SYSTEM” mode
n This
NOTE
parameter cannot be changed
“---” ............. : Motor minus (-) direction is set as the - direction.
“+++” ........... : Motor plus (+) direction is set as the + direction.
while servo is on.
This parameter cannot be changed while the servo is on. To change the parameter,
make sure the servo is off.
[Procedure]
1) Select “16. Motor direction” in “SYSTEM>PARAM>AXIS” mode.
4 c CAUTION
• YAMAHA can accept no liability
3) Select the axis with the cursor (↑/↓) keys.
from problems arising due to
Fig. 4-12-29 Setting the “Motor direction”
Operation
––– +++
4-170
12. “SYSTEM” mode
SYSTEM>PARAM>OTHER V8.35
Valid keys and submenu descriptions for editing other parameters are shown below.
4
Valid keys Menu Function
Operation
Cursor key
Moves the cursor up and down.
(↑/↓)
Page key
Switches to other screens.
<<
>>
( / )
F1 EDIT Edits the parameter.
F2 JUMP Moves the cursor to the designated parameter.
1. Display language
This parameter sets the language for displaying messages on the MPB.
[Procedure]
1) Select “1. Display language (JPN/ENG)” in “SYSTEM>PARAM>OTHERS” mode.
SYSTEM>PARAM>OTHER V8.35
4-171
12. “SYSTEM” mode
SYSTEM>PARAM>OTHER V8.35
SYSTEM>PARAM>OTHER V8.35
4-172
12. “SYSTEM” mode
SYSTEM>PARAM>OTHER V8.35
4
1.Display language(JPN/ENG) ENGLISH
2.Data display length 6char
Operation
3.Parameter display unit PULSE
4.DO cond. on EMG HOLD
5.Watch on STD.DIO DC24V VALID
RESET HOLD
SYSTEM>PARAM>OTHER V8.35
n When
NOTE
DC 24V is supplied, the STD.
DIO becomes valid regardless of the 1.Display language(JPN/ENG) ENGLISH
setting. 2.Data display length 6char
3.Parameter display unit PULSE
4.DO cond. on EMG HOLD
n NOTE
5.Watch on STD.DIO DC24V VALID
• Make sure this setting is enabled INVALID VALID
(valid) when the robot will be in
normal operation. 3) Press the (INVALID) or (VALID) key.
F 1 F 2
• The interlock signal sends a stop
command such as for stopping
robot operation. If the interlock
setting is off (disabled) use 4) Press the ESC key to quit the edit mode.
caution during robot operation.
4-173
12. “SYSTEM” mode
n NOTE
4 • When this parameter is valid
(enabled), return-to-origin will
always be incomplete each time
SYSTEM>PARAM>OTHER V8.35
n •NOTE
Command functions using DI05 of
This parameter sets whether to enable or disable the command function that uses DI05
of the STD.DIO connector. This is automatically set to "INVALID" when the parameters
the STD.DIO connector utilize part are initialized.
of the general-purpose input and
output. When you are utilizing a [Procedure]
general-purpose input and output,
the value may change so use caution 1) Select “7. IO cmd (DI05) on STD.DIO" in "SYSTEM>PARAM>OTHERS" mode.
when using such commands.
• For detailed information on I/O 2) Press the F 1 (EDIT) key.
commands, refer to the programming The function key menu changes.
manual.
Fig. 4-12-37
SYSTEM>PARAM>OTHER V8.35
4-174
12. “SYSTEM” mode
8. DI noise filter/SCANMD
This parameter sets whether to cancel external input signals (dedicated input signals,
general-purpose input signals) that might appear like noise in the form of short pulses.
When this parameter is set to "VALID", the on and off periods of input signals must be
longer than 25msec since the controller does not respond to any signal input shorter
than 25msec. This prevents the controller from responding to noise inputs.
[Procedure]
1) Select “8. DI noise filter” in “SYSTEM>PARAM>OTHERS” mode.
Operation
4.DO cond. on EMG HOLD
5.Watch on STD.DIO DC24V VALID
6.Incremental Mode control INVALID
7.IO cmd (DI05) on STD.DIO INVALID
8.DI noise filter VALID
INVALID VALID
4-175
12. “SYSTEM” mode
c IfCAUTION
this parameter is set to "VALID",
9. Skip undefined parameters
SYSTEM>PARAM>OTHER V8.35
4-176
12. “SYSTEM” mode
c For
CAUTION
detailed information on Ethernet
This section explains how to set parameters for option boards.
Option boards are roughly divided into three types: option DIO boards, serial I/O boards
and serial I/O units such as CC-link, and network board.
refer to their respective manuals.
For option DIO boards, you set a parameter to enable or disable monitoring of the DC
24V supply input. For serial I/O boards, you set three parameters including the parameter
to enable or disable the boards (CC_Link/DeviceNet/ProfiBUS). When using a network
board (Ethernet), you set four parameters including the parameter to enable or disable the
board.
[Procedure]
1) Press the F 5 (OP. BRD) key in "SYSTEM>PARAM” mode to enter the option
board parameter setting mode.
The option boards installed in the controller are displayed in order on the MPB
screen. 4
Fig. 4-12-40
Operation
SYSTEM>PARAM>OP.BRD V8.35
1.D_Net(M4/500K) VALID
2.DIO_N(1) VALID
3. ---
4. ---
SELECT
Option boards installed into the option slots are displayed on the MPB screen.
When editing the parameters for option boards, the following keys and submenu are valid.
4-177
12. “SYSTEM” mode
n Setting
NOTE
to "VALID" is recommended so
12.1.4.1 Option DIO setting
that the 24V supply for the option The following parameter for option DIO (NPN or PNP specifications) boards is used to
board is monitored during operation. enable or disable monitoring of the DC 24V supply input.
Set to "INVALID" only when option
boards that are not to be used are Parameter Meaning
installed.
1. Board condition Enables or disables monitoring of the 24V supply input. When set
to "VALID", an error message will be issued as a warning and
recorded in the error history if the DC 24V supply is shut off.
When set to "INVALID", no error message will be issued and
recorded in the error history even if the DC 24V supply is shut off.
c The
CAUTION
robot controller itself operates
[Procedure]
Fig. 4-12-41
even if DC 24V is not supplied to the
option board. However, an option
4 board not supplied with DC 24V will
not perform input/output operations
SYSTEM>PARAM>OP.BRD V8.35
3. ---
4. ---
SELECT
1) In “SYSTEM>PARAM>OP. BRD” mode, select the option DIO board with the
cursor keys and press the F 1 (SELECT) key.
Fig. 4-12-42
SYSTEM>PARAM>OP.BRD>SELECT V8.35
EDIT JUMP
Fig. 4-12-43
SYSTEM>PARAM>OP.BRD>SELECT V8.35
INVALID VALID
4-178
12. “SYSTEM” mode
n NOTE
• Set the Board status parameter to
12.1.4.2 Serial I/O setting
"INVALID" when not using serial For serial I/O boards, you can set the following 3 parameters including the parameter
I/O boards. used to enable or disable the serial I/O boards (CC_Link/DeviceNet/ProfiBUS).
• When the Board status parameter
is set to "INVALID", the dedicated Parameter Meaning
input/output of the STD.DIO
connector is enabled. When the 1. Board condition Enables or disables the serial I/O board. When set to "VALID" the
Board status parameter is set to serial I/O can be used. When set to "INVALID" the serial I/O
"VALID", the dedicated input cannot be used.
(except DI1) of the STD.DIO
connector is disabled. 2. Remote cmd / IO cmd Enables or disables the functions of remote commands and I/O
• For remote commands and I/O (SI05) commands using word information and bit information. When set
commands, refer to the command to "VALID" the remote commands and I/O commands can be used.
reference manual. When set to "INVALID" the remote commands and I/O commands
• For a description of codes issued cannot be used.
from the message output function This parameter cannot be set to "VALID" simultaneously with
for SOW(1), refer to "1. Error parameter 3.
Messages" in chapter 9.
• When the Remote command & I/O 3. Output MSG to SOW(1) Enables or disables the function that sends a message number,
4
command parameter is set to which is displayed on the MPB, to word information SOW(1).
"VALID", the Output MSG to When set to "VALID" the message number to be displayed on the
Operation
SOW(1) parameter cannot be set MPB will be output. When set to "INVALID" the message number
to "VALID". Likewise, when the to be displayed on the MPB will not be output. This parameter
Output MSG to SOW(1) parameter cannot be set to "VALID" simultaneously with parameter 2.
is set to "VALID", the Remote
command & I/O command
parameter cannot be set to [Procedure]
"VALID".
Fig. 4-12-44
SYSTEM>PARAM>OP.BRD V8.35
1.D_Net VALID
2.DIO_N(1) VALID
3. ---
4. ---
SELECT
1) In “SYSTEM>PARAM>OP. BRD” mode, select the serial I/O board with the cursor
keys and press the F 1 (SELECT) key.
Fig. 4-12-45
SYSTEM>PARAM>OP.BRD>SELECT V8.35
EDIT JUMP
4-179
12. “SYSTEM” mode
Fig. 4-12-46
SYSTEM>PARAM>OP.BRD>SELECT V8.35
EDIT JUMP
4 Fig. 4-12-47
SYSTEM>PARAM>OP.BRD>SELECT V8.35
Operation
INVALID VALID
4-180
12. “SYSTEM” mode
c When
CAUTION
making the Ethernet settings to
12.1.4.3 Setting the network parameters
use TELNET, you will need to set any When using Ethernet, you set four parameters including the parameter to enable or disable
other parameters than those shown the Ethernet board.
on the right. For more details, see the
Ethernet manual. Parameter Meaning
[Procedure]
Fig. 4-12-48
4
Operation
SYSTEM>PARAM>OP.BRD V8.35
1.E_Net VALID
2.
3.
4.
SELECT
1) In “SYSTEM>PARAM>OP. BRD” mode, select "E_Net" with the cursor keys and
press the F 1 (SELECT) key.
Fig. 4-12-49
SYSTEM>PARAM>OP.BRD>SELECT V8.35
Fig. 4-12-50
SYSTEM>PARAM>OP.BRD>SELECT V8.35
4-181
12. “SYSTEM” mode
c Changes
CAUTION
you made to the IP address
3) The currently set parameters are displayed.
When changing the "Board condition" parameter, press F 1 (INVALID) to
and subnet mask are enabled after
restarting the robot controller. When disable the Ethernet unit or press F 2 (VALID) to enable the Ethernet unit.
connecting the robot controller to an
existing network, always consult with When changing other parameters, use the 0 to 9 and . keys to
the network administrator for the IP
address, subnet mask and gateway make the setting and press the key.
settings.
4
Operation
4-182
12. “SYSTEM” mode
Operation
[Procedure]
1) Press the F 2 (CMU) key in “SYSTEM” mode.
The communication parameter screen appears.
SYSTEM>CMU V8.35
<<
5) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
4-183
12. “SYSTEM” mode
Valid keys and submenu descriptions in “SYSTEM>CMU” mode are shown below.
Page key
Switches to other screens.
<<
>>
( / )
F1 EDIT Edits the parameter.
F2 JUMP Moves the cursor to the designated parameter.
n NOTE
• Online commands can be executed
3) Select the communication mode with the F 1 (OFFLINE) or F 2 (ONLINE)
only in “ONLINE” mode. key.
• The CMU (communication) mode
can be changed with either
ONLINE or OFFLINE statements
4) Press the ESC key to quit the setting. To continue selecting other items, use the
in robot language.
cursor (↑/↓) keys.
4-184
12. “SYSTEM” mode
2. Data bits
This parameter sets the data bit length.
[Procedure]
1) Select “2. Data bits” in “SYSTEM>CMU” mode.
n Katakana
NOTE
letters (Japanese phonetic)
cannot be sent if data bit length was
set to 7 bits. 2) Press the F 1 (EDIT) key.
The function key menu changes.
SYSTEM>CMU V8.35
1.CMU mode
2.Data bits
ONLINE
8 4
3.Baud rate 9600
Operation
4.Stop bit 1
5.Parity ODD
7 8
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
3. Baud rate
This parameter sets the communication speed.
[Procedure]
1) Select “3. Baud rate” in “SYSTEM>CMU” mode.
n Communication
NOTE
errors are more prone
to occur at high communication 2) Press the F 1 (EDIT) key.
speeds. If communication errors The function key menu changes.
frequently occur, set a lower
communication speed.
Fig. 4-12-54 Setting the “Baud rate”
SYSTEM>CMU V8.35
3) Select the baud rate with the F 1 (4800) through F 5 (57600) keys.
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
4-185
12. “SYSTEM” mode
4. Stop bit
This parameter sets the stop bit length.
[Procedure]
n SetNOTE
to 2 bits if communication errors
1) Select “4. Stop bit” in “SYSTEM>CMU” mode.
frequently occur.
2) Press the F 1 (EDIT) key.
The function key menu changes.
SYSTEM>CMU V8.35
4 1.CMU mode
2.Data bits
ONLINE
8
3.Baud rate 9600
Operation
4.Stop bit 1
5.Parity ODD
1 2
3) Select the stop bit length with the F 1 (1) or F 2 (2) key.
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
5. Parity
This parameter sets the parity check.
[Procedure]
1) Select “5. Parity” in “SYSTEM>CMU” mode.
n Use the parity check as often as
NOTE
possible.
2) Press the F 1 (EDIT) key.
The function key menu changes.
SYSTEM>CMU V8.35
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
4-186
12. “SYSTEM” mode
6. Termination code
This parameter sets the line feed code.
[Procedure]
1) Select “6. Termination code” in “SYSTEM>CMU” mode.
SYSTEM>CMU V8.35
3.Baud rate
4.Stop bit
9600
1
4
5.Parity ODD
Operation
6.Termination code CR
7.XON/XOFF control YES
CR CRLF
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
7. XON/XOFF control
This parameter sets whether to control the data flow using XON/XOFF control.
[Procedure]
n Data
NOTE
omissions may occur if data flow
1) Select “7. XON/XOFF control” in “SYSTEM>CMU” mode.
SYSTEM>CMU V8.35
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
4-187
12. “SYSTEM” mode
8. RTS/CTS control
This parameter sets whether to control the data flow using RTS/CTS signal.
[Procedure]
n Data
NOTE
omissions may occur if data flow
1) Select “8. RTS/CTS CONTROL> in “SYSTEM>CMU “ mode.
control is not performed. Make use of
data flow control as much as possible.
2) Press the F 1 (EDIT) key.
The function key menu changes.
SYSTEM>CMU V8.35
4 4.Stop bit
5.Parity
1
ODD
6.Termination code CRLF
Operation
4-188
12. “SYSTEM” mode
SYSTEM>OPTION V8.35
4
Operation
POS.OUT SERVICE SIO
Parameters can be edited by entering data with the number keys or by selecting the
function keys. Refer to each parameter item for detailed information.
4-189
12. “SYSTEM” mode
• Always provide a margin when If the R axis is set, always make sure that the comparison point's R axis data is set.
setting the comparison point data.
When the comparison points are set as shown below, and the robot axis tip is moved
between the marks, the output is off at and the output is on at .
Fig. 4-12-61 When points are designated in Cartesian coordinates ("mm" unit system)
Comparison point 2
+Z
Comparison point 1 +Y
+X
4-190
12. “SYSTEM” mode
[Procedure]
1) Press F 1 (POS.OUT) in “SYSTEM>OPTION” mode to enter the area check
output mode.
SYSTEM>OPTION>POS.OUT V8.35
1.Output of area 1 NO
2.Output of area 2 NO
3.Output of area 3 NO
4.Output of area 4 NO
SELECT
4
2) Select an area check output number with the cursor (↑/↓) keys and press the F 1
Operation
(SELECT) key.
SYSTEM>OPTION>POS.OUT>SELECT V8.35
1.Output of area 1 NO
2.Port number of output 1 DO (20)
3.Compare point number 11 PO
4.Compare point number 12 PO
EDIT JUMP
Valid keys and submenu descriptions in this mode are shown below.
4-191
12. “SYSTEM” mode
n NOTE
• Select the robot for the area
1) Select “1. Output of area n” in “SYSTEM>OPTION>POS.OUT>SELECT” mode.
check.
• “SUB” cannot be selected if there 2) Press the F 1 (EDIT) key.
is no sub robot.
The function key menu changes.
SYSTEM>OPTION>POS.OUT>SELECT V8.35
4 1.Output of area 1
2.Port number of output 1
NO
DO (20)
3.Compare point number 11 PO
Operation
NO MAIN SUB
3) Select the robot for the area check with the F 1 (NO), F 2 (MAIN) or
F 3 (SUB) key.
Robot Details
MAIN The area check output is executed for the main robot.
SUB The area check output is executed for the sub robot.
4) Press the ESC key to quit the setting. To continue selecting other items, use the
n NOTE
• Output data might sometimes be
cursor (↑/↓) keys.
SYSTEM>OPTION>POS.OUT>SELECT V8.35
4-192
12. “SYSTEM” mode
3) Select the output port with the F 1 (DO(20)) through F 8 (DO(27)) keys.
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
n The
NOTE
units of comparison points 1 and
Set the point numbers for determining the area to perform area check.
4
2) Press the F 1 (edit) key.
The function key menu changes.
Operation
n NOTE
Fig. 4-12-66 Entering the comparison point numbers for area check output
• The area check is carried out on
all set axes. Take care when setting SYSTEM>OPTION>POS.OUT>SELECT V8.35
the R axis point if using the system
with four axes.
• Always provide a margin when 1.Output of area 1 MAIN
setting the comparison point data. 2.Port number of output 1 DO (20)
3.Compare point number 11 PO
4.Compare point number 12 PO
3) Enter the point number with the 0 to 9 keys and press the key.
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
Example: When the comparison points are set as shown below, and the robot axis tip
n Area
NOTE
check output is on when the is moved between the marks, the output is off at and the output is on at
current position is within the specified .
area, and off when outside the area.
Fig. 4-12-61 When points are designated in Cartesian coordinates ("mm" unit system)
Comparison point 2
+Z
Comparison point 1 +Y
+X
4-193
12. “SYSTEM” mode
w InWARNING
“SERVICE” mode, changing
There are 3 parameters for “SERVICE” mode.
* The Hold to Run function indicates that the robot operation (including program
execution) is executed only when the keys are held down on the MPB.
Description
ALL Allows MPB, dedicated input and online command operation devices.
4-194
12. “SYSTEM” mode
[Procedure]
1) Press F 2 (SERVICE) in “SYSTEM>OPTION” mode.
The message, “Enter password” appears on the guideline.
Enter “SAF” here and press the key.
SYSTEM>OPTION V8.35
Operation
2) The following screen appears when the correct password is entered.
SYSTEM>OPTION>SERVICE V8.35
Valid keys and submenu descriptions in this mode are shown below.
4-195
12. “SYSTEM” mode
Description
n The
NOTE
settings made here are only valid
Level 0 Disabled Allowed
[Procedure]
1) Select “1. Service level” in “SYSTEM>OPTION>SERVICE” mode.
4 w Settings may be changed but the
WARNING
SYSTEM>OPTION>SERVICE V8.35
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
4-196
12. “SYSTEM” mode
Description
Operation
responsibility for them. The
customer should keep safety in 1.Service level LEVEL 3
mind when making changes.
2.Movement Vel <3%
3.Operating device MPB
<100% <3%
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
4-197
12. “SYSTEM” mode
Description
n The
NOTE
settings made here are only valid
MPB Only MPB operation is allowed.
until the controller power is turned MPB/DI Allows MPB and dedicated input.
off. Save these settings if you want to
use them again after power is turned MPB/COM Allows MPB and online commands.
off.
ALL Allows operation by all devices.
[Procedure]
w Settings may be changed but the
WARNING 1) Select “3. Operating device” in “SYSTEM>OPTION>SERVICE” mode.
customer must bear
4 responsibility for them. The
customer should keep safety in 2) Press the F 1 (EDIT) key.
mind when making changes.
Fig. 4-12-71 Editing the "SERVICE" mode devices
Operation
SYSTEM>OPTION>SERVICE V8.35
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
4-198
12. “SYSTEM” mode
w InWARNING
“SERVICE” mode, changing
12.3.2.1 Saving the “SERVICE” mode parameters
the settings from their default To save the parameter settings for “SERVICE” mode, follow the procedure below.
values is likely to increase The parameter settings made here are only valid until the controller power is turned off,
hazards to the robot operator unless you save those settings.
during maintenance or
operation. Customers can [Procedure]
change these settings based on
their own responsibility, but 1) Press the F 4 (SAVE) key in “SYSTEM>OPTION>SERVICE” mode.
adequate consideration should
When you have made changes to the parameters, a message appears on the
first be given to safety.
guideline asking if you want to save the setting.
SYSTEM>OPTION>SERVICE V8.35
1.Service level
2.Movement Vel
LEVEL 3
<3%
4
3.Operating device MPB
Operation
Change OK? YES NO
SYSTEM>OPTION>SERVICE>HELP V8.35
2) Press the F 1 (NEXT P.) key to display the next message page.
Press the F 2 (PREV. P.) key to display the previous message page.
4-199
12. “SYSTEM” mode
n NOTE
• Output results might be incorrect
12.3.3 SIO settings
if the SIO specified port is the The serial I/O unit allows the master station sequencer (PLC) to send and receive parallel
same as the port used by the port ON/OFF data in the robot controller I/O unit, regardless of the robot program. This
program. function allows using I/O devices such as sensors and relays as serial-connected devices.
• These settings are only valid when
the serial I/O unit is connected. Fig. 4-12-74 SIO overview
Master station
PLC I/O device
(sensors, relays. etc.)
CC-Link
4 The relation between parallel and serial ports that can be set are shown below.
Parallel I/O connection
Operation
[Procedure]
1) Press the F 3 (SIO) key in "SYSTEM>OPTION” mode.
SYSTEM>OPTION>SIO V8.35
1.Direct SI2()->DO2() NO
2.Direct SI3()->DO3() NO
3.Direct SI4()->DO4() NO
4.Direct SI5()->DO5() NO
5.Direct SO2()<-DI2() NO
EDIT JUMP
Valid keys and submenu descriptions in this mode are shown below.
4-200
12. “SYSTEM” mode
n Output
NOTE
results might be incorrect if the
1. Direct connection from SI n ( ) to DO n ( )
SIO specified port is the same as the The serial port input can be directly connected to parallel port output. The relation
port used by the program. between parallel and serial ports that can be set is as follows.
[Procedure]
1) Select from 1 to 4 in "SYSTEM>OPTION>SIO" mode.
4
2) Press the F 1 (EDIT) key.
Operation
Fig. 4-12-76 Editing the SIO settings (1)
SYSTEM>OPTION>SIO V8.35
1.Direct SI2()->DO2() NO
2.Direct SI3()->DO3() NO
3.Direct SI4()->DO4() NO
4.Direct SI5()->DO5() NO
5.Direct SO2()<-DI2() NO
EDIT JUMP
3) Press the F 1 (SET) key to set the direct connection or press the F 2 (NO)
key not to set it.
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
4-201
12. “SYSTEM” mode
n Output
NOTE
results might be incorrect if the
2. Direct connection from DI n ( ) to SO n ( )
SIO specified port is the same as the Parallel port input can be directly connected to serial port output. The relation between
port used by the program. serial and parallel ports that can be set is as follows.
[Procedure]
1) Select from 5 to 8 in "SYSTEM>OPTION>SIO" mode.
4
2) Press the F 1 (EDIT) key.
Operation
SYSTEM>OPTION>SIO V8.35
4.Direct SI5()->DO5() NO
5.Direct SO2()<-DI2() NO
6.Direct SO3()<-DI3() NO
7.Direct SO4()<-DI4() NO
8.Direct SO5()<-DI5() NO
SET NO
3) Press the F 1 (SET) key to set the direct connection or press the F 2 (NO)
key not to set it.
4) Press the ESC key to quit the setting. To continue selecting other items, use the
cursor (↑/↓) keys.
4-202
12. “SYSTEM” mode
12.4 Initialization
When initializing the parameter data you entered, follow the descriptions in this section.
[Procedure]
1) Press the F 4 (INIT) key in “SYSTEM” mode.
The initialization screen appears.
SYSTEM>INIT V8.35
Operation
PARAM MEMORY CMU CLOCK
Valid keys and submenu descriptions in “SYSTEM>INT” mode are shown below.
4-203
12. “SYSTEM” mode
4 SYSTEM>INIT V8.35
Operation
Enter password>_
2) When the correct password was entered, a confirmation message appears on the
guideline.
SYSTEM>INIT>PARAM V8.35
ROBOT = YK400X
D1=M1: aYK400X D5=M5: no axis
D2=M2: aYK400X D6=M6: no axis
D3=M3: aYK400X
D4=M4: aYK400X
Initialize OK? YES NO
4-204
12. “SYSTEM” mode
n NOTE
• External data must be input to
SYSTEM>INIT>MEMORY V8.35
Operation
PROGRAM POINT SHIFT HAND ALL
SYSTEM>INIT>MEMORY>PROGRAM V8.35
4-205
12. “SYSTEM” mode
[Procedure]
1) Press the F 3 (CMU) key in “SYSTEM>INIT” mode.
A confirmation message appears on the guideline
SYSTEM>INIT>CMU V8.35
MODE ,DATA,RATE,STOP,PARI,TERM,XON,RTS
ONLINE, 8,9600, 1 ,ODD ,CRLF,YES,NO
4-206
12. “SYSTEM” mode
c The
CAUTION
clock used in the controller might
[Procedure]
differ from the correct time. 1) Press the F 4 (CLOCK) key in “SYSTEM>INIT” mode.
If this happens, set the correct time. The present date and time are displayed.
SYSTEM>INIT>CLOCK V8.35
DATE,TIME :04/08/21,10:13:35
4
DATE TIME
Operation
2) Select the item with the F 1 (DATE) or F 2 (TIME) key.
A confirmation message appears on the guideline.
3) Enter the date or time in the specified format and then press the key.
Enter this data using the 0 to 9 , / and : keys.
4-207
12. “SYSTEM” mode
c CAUTION
• If you change the system
Should the memory for the system generation be destroyed by some serious problem the
user must make the correct system generation settings. To protect the equipment against
generation by mistake, this may such accidents, save the initial parameter data when shipped from YAMAHA and the
adversely effect robot operation
or create operator hazards.
parameter data from system upgrades onto an external PC storage device by way of the
Always consult YAMAHA if RS232C.
changes have been made.
• Please note that YAMAHA cannot Refer to the maintenance manual for system generation operating methods.
be held liable for problems
resulting from changing the
4-208
12. “SYSTEM” mode
SYSTEM>DIAGNOS V8.35
Operation
CHECK HISTRY
Valid keys and submenu descriptions in “SYSTEM>DIAGNOS” mode are shown below.
SYSTEM>DIAGNOS>CHECK V8.35
n NOTE
• An error message will always System check OK !!
appear if DC 24V is not supplied
to STD.DIO.
• An error message will always
appear if DC 24V is not supplied
to the option DIO.
NEXT P. PREV.P.
4-209
12. “SYSTEM” mode
SYSTEM>DIAGNOS>HISTRY V8.35
1:04/08/01,10:15:00 12.1:Emg.stop on
2:04/08/01,10:14:54 22.1:AC power low
3:04/08/01,09:59:34 17.4:D1,Over load
4 4:04/07/28,14:00:02 12.1:Emg.stop on
5:04/06/30,08:40:10 22.1:AC power low
NEXT P. PREV.P. CLEAR
Operation
One screen displays the past 5 errors in order from the most recent error.
Error information is displayed in the following format.
<Date>, <Time> <Error No.>:<Error message>
* The hour, minute and second are displayed for the time.
c CAUTION
• Errors are not recorded when
2) Check the error history.
identical to a preceding error that Pressing the cursor (↑/↓) keys changes the display one line at a time.
just occurred. Pressing the F 1 (NEXT P.) or F 2 (PREV. P.) key changes the display one
• The error category “0” is not
recorded. screen at a time.
• The error history is initialized
when the F 5 (CLEAR) key is
used. Do not initialize if you want 3) Press the F 5 key if you want to clear the error history.
to retain the error history.
4-210
12. “SYSTEM” mode
SYSTEM>DIAGNOS>SYS.CHK V8.35
Operation
"No system error code" will appear if no error has occurred.
4-211
12. “SYSTEM” mode
SYSTEM>BACKUP V8.35
4
Operation
F5 FROM Saves and recovers data with the internal flash ROM.
n IfNOTE
the data in the internal memory is
1) Press the F 5 (FROM) key in the "SYSTEM" mode.
4-212
12. “SYSTEM” mode
SYSTEM>BACKUP>FROM>LOAD V8.35
Operation
c CAUTION
• When reading data with ALL files .ALL .PGM .PNT .SFT .HND
or as parameter files, the servo
must be off. After the files are Valid keys and submenu descriptions in "SYSTEM>BACKUP>FROM>LOAD"
read in, the return-to-origin mode are shown below.
incomplete state will be set.
• Data saved in the internal flash
ROM cannot be loaded back if Valid keys Menu Function
any hardware trouble occurs.
Always save the data onto an F1 .ALL Files are loaded as ALL files.
external PC storage device.
F2 .PGM Only program files are loaded.
• If an abnormal process occurs,
such as if the power is turned F3 .PNT Only point files are loaded.
OFF while saving data, the data
cannot be guaranteed. F4 .SFT Only shift files are loaded.
SYSTEM>BACKUP>FROM>LOAD>.PGM V8.35
4-213
12. “SYSTEM” mode
n IfNOTE
the data in the internal memory is
12.6.1.2 Saving files
destroyed for any reason, it can be The data in the controller's internal memory are saved as ALL files on the flash ROM. The
restored by loading the backup data data cannot be saved separately. If data is already saved, the new data cannot be saved
from the internal flash ROM. We until the files are initialized.
recommend backing up the data in the
internal flash ROM before starting the [Procedure]
robot system.
1) Press the F 2 (SAVE) key in the "SYSTEM>BACKUP>FROM" mode.
c CAUTION
• If data has already been written
Press F 4 (YES) to save the data.
c CAUTION
• If data is already written in, the Fig. 4-12-94 Check of FROM initialization
data must be saved after the
initialization process. SYSTEM>BACKUP>FROM>INIT V8.35
• The data saved on the internal
flash ROM cannot be restored if
any hardware trouble occurs. No File Ext Size Data Time
Always save the data onto an 1 FROM .ALL 311800 04/07/22 17:32
external PC storage device.
• If an abnormal process occurs,
such as if the power is turned
OFF while initializing the data,
then the data cannot be
guaranteed. Initialize OK? YES NO
4-214
13. “MONITOR” mode
The “MONITOR” mode displays the I/O status regardless of the current mode and level.
The “MONITOR” mode display is overlapped onto the screen during normal operation.
So the robot controller can still be operated even with the monitor screen displayed.
[Procedure]
1) Press the DISPLAY key.
Input status is displayed in the data area (3rd to 7th lines) as shown below.
Operation
EDIT TEACH JUMP VEL+ VEL-
Display format:
<Port No.> = &B<bit 7><bit 6> to <bit 0>
DI monitor
DI10()=&B00000101 DI14()=&B00000000
DI11()=&B00000010 DI15()=&B00000000
DI12()=&B00000000 DI16()=&B00000000
DI13()=&B00000000 DI17()=&B00000000
EDIT TEACH JUMP VEL+ VEL-
4-215
13. “MONITOR” mode
n The
NOTE
screen display is updated at
periodic intervals.
4) To view the previous screen, press the LOWER + DISPLAY key.
Pressing the LOWER + DISPLAY key changes the screen in the reverse of the sequence
shown in 3).
DI monitor
DI0()=&B00000101 DI4()=&B00000000
DI1()=&B00000001 DI5()=&B00000000
DI2()=&B00000000 DI6()=&B00000000
DI3()=&B00000000 DI7()=&B00000000
EDIT TEACH JUMP VEL+ VEL-
SIW monitor
SIW(0)=&H0000 SIW(4)=&H0000
SIW(1)=&H0000 SIW(5)=&H0000
SIW(2)=&H0000 SIW(6)=&H0000
SIW(3)=&H0000 SIW(7)=&H0000
EDIT TEACH JUMP VEL+ VEL-
Task monitor:Line(Status),Pri
T1 = 6(RUN),32 T5 =
T2 = 10(SUS),32 T6 =
T3 = T7 =
T4 = T8 = 12(RUN),35
EDIT TEACH JUMP VEL+ VEL-
4-216
13. “MONITOR” mode
Operation
4-217
14.“UTILITY” mode
The “UTILITY” mode can be entered from any other mode regardless of the mode level.
[Procedure]
1) Press the UTILITY ( LOWER + ESC ) key.
n The
NOTE
current internal controller The “UTILITY” mode screen is displayed.
temperature is displayed on the right
end of the 3rd line. Fig. 4-14-1 “UTILITY” mode
UTILITY
UTILITY
Valid keys and submenu descriptions in “UTILITY” mode are shown below.
4-218
14. “UTILITY” mode
(1) When the emergency stop button was released after pressing the emergency stop
button.
(2) When the switch contact was closed after triggering emergency stop by opening
the emergency stop input contact.
[Procedure]
1) Press the UTILITY ( LOWER + ESC ) key to enter “UTILITY” mode.
(You can switch to “UTILITY” mode from any other mode.)
4
The “UTILITY” mode screen appears with a confirmation message shown on the
Operation
guideline.
UTILITY
2) Press the F 4 (YES) key to cancel the internal emergency stop flag.
The internal emergency stop flag is cancelled. You can then move on to the next
operation explained in 14.1.2, "Motor power and servo on/off”.
If not canceling the internal emergency stop flag, press the F 5 (NO) key.
4-219
14. “UTILITY” mode
2) Press the F 1 (ON) key to turn on the motor power supply and servo.
Press the F 2 (OFF) key to turn off the motor power supply and servo.
Press the F 6 (POWER) key to turn on the motor power supply only.
UTILITY>MOTOR
Operation
3) Press the ESC key to return to the mode selected just previous to “UTILITY”
mode.
4) To set the servo of each axis to “ON”, “OFF” or “FREE”, select the axis with the
cursor (↑/↓) keys.
When setting the servo to “ON”, the servo power for the axis must be turned on
beforehand by the operation in step 2.
UTILITY>MOTOR
Motor power: ON
D1=M1: Free D5=M5: no axis
D2=M2: Servo D6=M6: no axis
D3=M3: Servo
D4=M4: Servo
4-220
14. “UTILITY” mode
Operation
for sequence execution.
Scan Time : 10msec
2. Sequence execution must be
enabled. Sequence : ENABLE
3. DI10 contact point must be closed.
4. Operation must be in “AUTO”
mode or “MANUAL” mode.
ENABLE DISABLE
4-221
14. “UTILITY” mode
UTILITY>ARMTYPE
4 Arm type
at Present
:
:Main robot : RIGHTY
Sub robot : LEFTY
Operation
RIGHTY LEFTY
4-222
14. “UTILITY” mode
UTILITY >REST.DO
Operation
Reset output ports OK? YES NO
4-223
14. “UTILITY” mode
Description
Level Program When power is turned on Program reset Return-to-origin
execution at at program start signal in AUTO
origin incomplete Mode Program reset mode
LEVEL0 Disabled MANUAL mode NO NO Invalid
LEVEL1 Enabled MANUAL mode NO NO Invalid
4 LEVEL2 Enabled MANUAL mode YES NO Invalid
LEVEL3 Enabled AUTO mode NO NO Invalid
Operation
Note 1: When the absolute reset input (DI17) is valid in “AUTO” mode, the "Robot
program-in-progress" (DO13) signal turns on during processing by the absolute
reset input (DI17).
4-224
14. “UTILITY” mode
Fig.4-14-9
UTILITY
Operation
EXECUTE ACCESS RST.DO
Fig.4-14-10
UTILITY>EXECUTE
4-225
14. “UTILITY” mode
Fig.4-14-11
UTILITY>EXECUTE>HELP
NEXT P. PREV. P.
Fig.4-14-12
UTILITY>EXECUTE>HELP
NEXT P. PREV. P.
4-226
14. “UTILITY” mode
Operation
6. When hand data was destroyed
(when “9.7: Hand data destroyed” 14.6.1 Entering the password
message was displayed)
7. When a parameter was destroyed The password must be entered in order to change the access level.
(when “9.4: Parameter destroyed”
message was displayed) [Procedure]
8. When generation data was 1) Press the F 2 (ACCESS) key in “UTILITY” mode.
destroyed (when “9.33: Sys.
generation destroyed” message A message “Enter password” appears on the guideline. Enter with "LVL" here and
was displayed)
press the key.
UTILITY
Enter password>LVL_
UTILITY>ACCESS
4-227
14. “UTILITY” mode
UTILITY>ACCESS
4
LEVEL0 LEVEL1 LEVEL2 LEVEL3 HELP
Operation
UTILITY>ACCESS>HELP
NEXT P. PREV. P.
UTILITY>
>ACCESS>HELP
4-228
Chapter 5
Parallel I/O interface
Contents
1. Standard I/O interface overview ...................................................... 5-1
1.1 Power supply ........................................................................................ 5-1
1.2 Connector I/O signals ........................................................................... 5-2
1.3 Connector pin numbers ........................................................................ 5-3
1.4 Typical input signal connection ............................................................ 5-4
1.5 Typical output signal connection .......................................................... 5-5
1.5.1 Dedicated outputs .................................................................................. 5-5
1.5.2 General-purpose outputs ........................................................................ 5-6
1.6 Dedicated input signal description ........................................................ 5-7
1.7 Dedicated output signal description ...................................................... 5-9
1.8 Dedicated I/O signal timing chart ....................................................... 5-11
1.8.1 Controller power ON, servo ON and emergency stop .......................... 5-11
1.8.2 Absolute reset ...................................................................................... 5-12
1.8.3 Switching to AUTO mode, program reset and execution ...................... 5-13
1.8.4 Stopping due to program interlocks ...................................................... 5-14
1.9 General-purpose I/O signals ................................................................ 5-15
1.9.1 General-purpose input signals .............................................................. 5-15
1.9.2 General-purpose output signals ............................................................ 5-15
1.9.3 General-purpose output signal reset (off) .............................................. 5-15
n OnNOTE
General-purpose : 8
the robot controller with “SAFE”
mode enabled, dedicated inputs may
not be used in “SERVICE” mode
depending on the operating device
1.1 Power supply
setting in “SERVICE” mode.
The standard I/O interface uses an external 24V power supply. Connect the 24V and
ground terminals of the external power supply to pins 47 to 50 of the STD. DIO connector
on the controller.
5
n NOTE
5-1
1. Standard I/O interface overview
5-2
1. Standard I/O interface overview
33 19 1
32
50 18
Connection side
32
18 50
5-3
1. Standard I/O interface overview
DI 01
DI 10
DI 11
DI 12
to
DI 17
DI 20
DI 21
5 Protective
circuit
DI 22 NPN
DI 23
Parallel I/O interface
to
DI 36 External
power
supply
DI 37
Controller side
PNP specifications
Protective
circuit
DI 01
DI 10
DI 11
DI 12
to
DI 36
DI 37 PNP
External
power
supply
Controller side
5-4
1. Standard I/O interface overview
DO 01a
DO 01b
DO 02a
DO 02b
DO 03a
DO 03b
DO 10
5
to
Controller side
PNP specifications
COMMON
DO 01a
DO 01b
DO 02a
DO 02b
DO 03a
DO 03b
DO 10
to
DO 14
Controller side
5-5
1. Standard I/O interface overview
Controller side
PNP specifications
5 DC24V
External power
Parallel I/O interface
supply DC 24V
DO 20 to DO27
Controller side
5-6
1. Standard I/O interface overview
c CAUTION
• If a rise of the DI05 signal is
2. DI05 I/O command execution trigger input
DI05 is used to execute an I/O command.
recognized, the robot might begin
to move. In this case, the output When the command code to be executed is assigned to DI2() and command data to
signals of DO(26) and DO(27) DI3() and DI4(), and the DI05 contact is closed (ON), the I/O command will be executed
will also change. at the rise of the signal. Upon receiving the I/O command, the controller executes the
• When no I/O commands are used,
set the "IO cmd (DI5) on
required task. The progress information during the command execution and decision
STD.DIO/STDPRM" parameter results after the command execution are output.
to "INVALID" by referring to • Input signal pulse width: 100ms minimum
"12.1.3 Other parameters" in
Chapter 4.
• For detailed information on I/O
3. DI10 Sequence control input
5
commands, refer to the DI10 is used to execute a sequence program.
n The
NOTE
rise of DI12 has the same function
5. DI12 Program start input
DI12 is used to start the program.
as the START key.
When the DI12 contact is closed (ON) in “AUTO” mode, the robot program starts at
the rising edge of the signal pulse. DO13 (Robot program-in-progress) is issued when
c When
CAUTION
the program execution is
the robot program is executed.
stopped by a signal such as DI11 • Input signal pulse width: 100ms minimum
(Interlock input), the program re-
executes the command that has
stopped. 6. DI13 AUTO mode input
DI13 is used to switch to “AUTO” mode.
When the DI13 contact is closed (ON), operation switches to “AUTO” mode at the
rising edge of the signal pulse.
• Input signal pulse width: 100ms minimum
c Signal
CAUTION
input to DI14 is prohibited. Do
not connect any signal to DI14.
5-7
1. Standard I/O interface overview
n The
NOTE 9. DI17 Absolute reset input
c DI01,
CAUTION
DI12, DI13, DI15, DI16 and
start at the rising edge of the signal pulse.
Absolute reset can only be performed on axes using the stroke-end or sensor method
DI17 are inoperative while the for return-to-origin.
program is being executed. Input
these signals only after the program Absolute reset is not performed on axes which use the mark method for return-to-
is halted. origin. Absolute reset cannot be performed by dedicated input when return-to-origin is
incomplete.
• Input signal pulse width: 100ms minimum
5-8
1. Standard I/O interface overview
The ALARM LED on the controller monitor panel lights up simultaneously when an
alarm is triggered.
The alarm can be turned under the following conditions for each of the above cases.
In case (1)
After the emergency stop switch contacts have been closed, alarm turns off when
the emergency stop flag is canceled in “UTILITY” mode or the servo ON input
(DI01) of the I/O interface is turned on.
(This alarm can also be cancelled after the power is turned on again.)
In case (2)
Alarm turns off when the emergency stop flag is cancelled in “UTILITY” mode.
However, the alarm condition is maintained while the driver unit still has power so
the power must be turned off and then on again in order to turn on the servos and
restart the program.
5-9
1. Standard I/O interface overview
In case (3)
Since the CPU has stopped, the alarm cannot be turned off and operation cannot be
reset unless the power supply is turned on again.
In case (4)
When a battery abnormality is detected, the alarm cannot turn off until the power
supply is turned on again.
If the alarm is still on even after the power has been turned on again, then the battery
connections must be checked or the battery replaced.
5-10
1. Standard I/O interface overview
on
Servo ON input: DI(01)
off
a) b) c) d) e) f) g) h) i)
* If the emergency stop input contacts are open or a major error (malfunction) occurs
when the controller power is turned on, the servo remains off. Likewise, if SAFE
mode or serial I/O setting is enabled, the controller starts up with the servo turned off.
* When processing with dedicated inputs, use I/O signals to perform handshake
processing. If handshake processing is impossible, hold the signal for a minimum of
100ms.
5-11
1. Standard I/O interface overview
5-12
1. Standard I/O interface overview
on
AUTO mode output: DO(10)
off
on
Return-to-origin complete
output: DO(11) off
on
Robot program-in-progress
output: DO(13) off
on
Program reset status
output: DO(14) off
on
Interlock input: DI(11)
off
Program start input: DI(12) on
off
AUTO mode input: DI(13) on
off
Program reset input: DI(15) on
5
off
Program reset
d) Program reset input turns on.
e) Program reset status output turns on.
f) Program reset input turns off after checking program reset status output is turned on.
Program execution
g) Program start input turns on.
h) Program reset status input turns off, and robot program-in-progress output turns on.
i) Program start input turns off after checking robot program-in-progress output is turned
on.
* Program cannot be executed when the emergency stop input and interlock input are
off.
* If the return-to-origin complete output is off, the program might not be executed,
depending on the execution level setting.
5-13
1. Standard I/O interface overview
on
AUTO mode output: DO(10)
off
on
Return-to-origin complete
output: DO(11) off
on
Robot program-in-progress
output: DO(13) off
on
Interlock input: DI(11)
off
on
Program start input: DI(12)
off
a) b) c) d)e) f) g) h) i)
100ms or more
5 Program execution
a) Program start input turns on.
b) Robot program-in-progress output turns on.
Parallel I/O interface
c) Program start input turns off after checking robot program-in-progress output is turned
on.
* Program will stop if switching to emergency stop. An alarm is output at this time and
the servo-ON output turns off. The servo must be turned on to execute the program
again.
5-14
1. Standard I/O interface overview
All output signals are initialized when the controller power is turned on.
5-15
2. Option I/O interface overview
The option I/O interface of the controller is expandable to a maximum of 4 units for compatibility with
customer systems. A description of each I/O terminal and its connection is given here. Connect these
I/O terminals correctly and efficiently.
This option I/O interface contains 24 general-purpose inputs and 16 outputs. The type of
c See
CAUTION
"7. I/O connections" in Chapter
option I/O interface (NPN or PNP specifications) is set prior to shipment.
Inputs are referred to here as DI (Digital Inputs) and outputs as DO (Digital Outputs).
3 for a definition of NPN and PNP
specifications. Specifications
Connector Connector type Conductor wire
ID Number of I/O points name No.
General-purpose input : 24
1
General-purpose output : 16
5 4
General-purpose input : 24
General-purpose output : 16
Parallel I/O interface
The ID in the above table are set by the DIP switch on the option I/O interface unit.
5-16
2. Option I/O interface overview
2.1 ID settings
Use the DIP switch on the option I/O interface unit (adjacent to OPT. DIO connector) to
set the ID.
Fig. 5-2-1
DIP switch
The DI/DO ports are assigned based on these ID. ( ■ : switch lever)
1 2
2 DI100 to DI107
DI110 to DI117
DO60 to DO67
5
c Always
CAUTION DI120 to DI127 DO70 to DO77
5-17
2. Option I/O interface overview
5 15
16
DI54
DI55
DI104
DI105
DI134
DI135
DI164
DI165
Input 54 Input 104 Input 134 Input 164 Photocoupler input
Input 55 Input 105 Input 135 Input 165 NPN specifications: source type
17 DI56 DI106 DI136 DI166 Input 56 Input 106 Input 136 Input 166 PNP specifications: sink type
Parallel I/O interface
18 DI57 DI107 DI137 DI167 Input 57 Input 107 Input 137 Input 167
19 DI60 DI110 DI140 DI170 Input 60 Input 110 Input 140 Input 170
20 DI61 DI111 DI141 DI171 Input 61 Input 111 Input 141 Input 171
21 DI62 DI112 DI142 DI172 Input 62 Input 112 Input 142 Input 172
22 DI63 DI113 DI143 DI173 Input 63 Input 113 Input 143 Input 173
23 DI64 DI114 DI144 DI174 Input 64 Input 114 Input 144 Input 174
24 DI65 DI115 DI145 DI175 Input 65 Input 115 Input 145 Input 175
25 DI66 DI116 DI146 DI176 Input 66 Input 116 Input 146 Input 176
26 DI67 DI117 DI147 DI177 Input 67 Input 117 Input 147 Input 177
27 P.COM A P.COM A + common
28 DO30 DO50 DO70 DO110 Output 30 Output 50 Output 70 Output 110 Transistor output
29 DO31 DO51 DO71 DO111 Output 31 Output 51 Output 71 Output 111 NPN or PNP specifications
30 DO32 DO52 DO72 DO112 Output 32 Output 52 Output 72 Output 112 Maximum capacity of each
31 DO33 DO53 DO73 DO113 Output 33 Output 53 Output 73 Output 113 output terminal
32 DO34 DO54 DO74 DO114 Output 34 Output 54 Output 74 Output 114 (resistance load): 100mA
33 DO35 DO55 DO75 DO115 Output 35 Output 55 Output 75 Output 115 Common terminals:
34 DO36 DO56 DO76 DO116 Output 36 Output 56 Output 76 Output 116 + common terminal: P. COM A
35 DO37 DO57 DO77 DO117 Output 37 Output 57 Output 77 Output 117 - common terminal: N. COM A
36 N.COM A N.COM A - common
37 P.COM B P.COM B +common
38 DO40 DO60 DO100 DO120 Output 40 Output 60 Output 100 Output 120 Transistor output
39 DO41 DO61 DO101 DO121 Output 41 Output 61 Output 101 Output 121 NPN or PNP specifications
40 DO42 DO62 DO102 DO122 Output 42 Output 62 Output 102 Output 122 Maximum capacity of each
41 DO43 DO63 DO103 DO123 Output 43 Output 63 Output 103 Output 123 output terminal
42 DO44 DO64 DO104 DO124 Output 44 Output 64 Output 104 Output 124 (resistance load): 100mA
43 DO45 DO65 DO105 DO125 Output 45 Output 65 Output 105 Output 125 Common terminals:
44 DO46 DO66 DO106 DO126 Output 46 Output 66 Output 106 Output 126 + common terminal: P. COM B
45 DO47 DO67 DO107 DO127 Output 47 Output 67 Output 107 Output 127 - common terminal: N. COM B
46 N.COM B N.COM B - common
47
NC Not used
48
49
NC Not used
50
5-18
2. Option I/O interface overview
33 19 1
32
50 18
Connection side
1 33
19 Connector type: MR-50LM
32
18 50
5-19
2. Option I/O interface overview
DI
External
power
DI supply
N.COM DI
External power
supply is used. P.COM A,B
DO YYY
to
5-20
2. Option I/O interface overview
5-21
3. Ratings
1. Input
NPN specifications
c See
CAUTION
"7. I/O connections" in Chapter DC input (positive common type)
Method
3 for a definition of NPN and PNP Photocoupler insulation method
specifications.
Input power DC 24V±10%, 10mA/point
PNP specifications
2. Output
(1) Transistor output
5 NPN specifications
PNP specifications
Contact service life Electrical open/close 100,000 times (DC 24V with resistance load)
5-22
4. Caution items
1. When using a dual-lead proximity sensor as an input signal, check whether
or not it is within input signal specifications.
If the sensor has a high residual voltage during on and off, this might cause
possible malfunctions.
3. If a short occurs in the load or an excessive current flows, the internal over-
current protective circuit shuts off the interface circuit. Once this protective
circuit is activated, it is not possible to restore the previous state.
Furthermore, heat generated inside might damage the internal circuits, so
always draw current only within the rated load.
4. As a noise prevention, keep the machine power cables separate and make
sure wires are well shielded.
5
5-23
MEMO
5-24
Chapter 6 SAFETY I/O interface
Contents
1. SAFETY I/O interface overview ........................................................ 6-1
1.1 Power ................................................................................................... 6-1
1.2 Connector I/O signals ........................................................................... 6-1
1.3 Connector terminal numbers ................................................................. 6-2
1.4 Emergency stop input signal connections .............................................. 6-3
1.5 Dedicated input signal connections ...................................................... 6-6
1.6 Input signal description ......................................................................... 6-7
MEMO
1. SAFETY I/O interface overview
The robot controller is provided with SAFETY I/O interfaces for compatibility with the
system used by the customer. A description of the I/O terminals and connection methods
are explained below.
Connect the I/O terminals correctly for effective operation.
The SAFETY I/O interface contains an emergency stop input and one dedicated input
point.
The input signal is from hereon referred to as DI and the output signal as DO.
SAFETY Emergency stop input : 1 point SAFETY D-SUB15 (male) 0.3mm2 or more
Dedicated input : 1 point
1.1 Power
The emergency stop input utilizes internal power for emergency stop.
The dedicated input utilizes external 24V power connected via the standard I/O interface.
6-1
1. SAFETY I/O interface overview
8 15
1 9
Connection side
6
SAFETY I/O interface
Solder side
15 8
9 1
6-2
1. SAFETY I/O interface overview
1 3 EMG 24V
14 EMG RDY
Motor power
relay coil
GND
GND
Motor power
supply circuit
AC 200V power supply
6
6-3
1. SAFETY I/O interface overview
Connections using the MPB-E2 (MPB compatible with an enable switch) with
external emergency stop circuit (PNP specifications)
Emergency Enable
stop switch switch
c External
CAUTION
emergency stop and the
MPB connector
13
MPB emergency stop button are
disabled when pin 13 and pin 14 are 14
directly shorted to each other on the 15
SAFETY connector. Make 16
connections to ensure the system 17
including the robot controller will
18
always operate safely.
19
20
MPB-E2
SAFETY Service key
connector switch
Emergency
3 EMGIN1 stop switch
4 EMGIN2
5 EMGIN3
6 EMGIN4
7 LCKIN1
8 LCKIN2
9 LCKIN3
24V
10 LCKIN4
6 13
14
EMG24V
EMGRDY
1 DI02
11
SAFETY I/O interface
P.COM
GND
Motor power
supply circuit
AC 200V power supply
Operation description:
• The MPB-E2 emergency stop switch and external emergency stop switch are connected
in series. The enable switch is also connected in series to the MPB-E2 emergency stop
switch, but can be bypassed with the service key switch.
c CAUTION
• EMG RDY requires at least
a. In normal operation, EMG 24V is connected to EMG RDY via the MPB-E2
emergency stop switch and SAFETY connector, and turns on the controller internal
100mA for the relay and motor power relay.
photocoupler drive current.
• Do not use EMG 24V for b. When emergency stop is triggered, power to EMG RDY of the SAFETY connector
anything other than emergency is cut off and the motor power supply turns off. Emergency stop is triggered if the
stop. MPB-E2 and SAFETY connector are removed.
6-4
1. SAFETY I/O interface overview
6-5
1. SAFETY I/O interface overview
c See
CAUTION
"7. I/O connections" in Chapter
1.5 Dedicated input signal connections
3 for a definition of NPN and PNP
specifications. NPN specifications
DI02
n Connect
NOTE
DC 24V and ground for STD.
Protective
circuit
DIO.
N.COM
PNP specifications
Protective
circuit
n Connect
NOTE
DC 24V and ground for STD.
DI02
DIO.
6-6
1. SAFETY I/O interface overview
c See
CAUTION
"7. I/O connections" in Chapter
1.6 Input signal description
3 for a definition of NPN and PNP
specifications.
1. DI02 SERVICE mode input
Service mode input can only be used on robot controllers with SAFE mode enabled.
When the DI02 contact is open (OFF), the robot controller service mode is set for
exclusive control for operating levels, operating speed limits and operating devices
conforming to the service mode parameter settings. Normal mode is enabled when the
n NOTE
• NPN and PNP specifications are DI02 contacts are closed (ON). When a serial I/O option board is installed, the service
determined by the STD. DIO mode is controlled by a logic AND circuit comprised of SI02 and DI02.
setting.
If the service mode input is changed, the program being executed will pause or ongoing
• Robot controllers with SAFE mode
enabled will always be in service robot jog movement will pause.
mode when an external 24V is not
supplied to STD. DIO. This can be
cancelled using a software 2. DI00 Emergency stop inputs 1, 2, 3, 4
parameter.
• A 10mA input current is required. Emergency stop signal inputs are used when making the interlock circuit to ensure the
system including the robot controller will operate safely. Contacts must be closed for
the system to function normally. Refer to the connection examples in this chapter
when making actual connections.
Closing the emergency stop contact points (ON) allows turning on the servo power
supply. The servo power supply cannot be turned on when the emergency stop contact
points are open (OFF).
Emergency stop signal inputs 3 and 4 are valid only when an MPB-E2 (MPB compatible
with an enable switch) is used. 6
6-7
MEMO
6-8
Chapter 7 RS-232C interface
Contents
1. Communication overview ................................................................ 7-1
The robot controller can communicate with external devices in the following 2 modes using the RS-
232C interface.
These modes can be used individually or jointly in a variety of applications.
(2) Various commands are transmitted directly through a communication port from the
external devices. These commands are called online commands.
If this function is used, some operations can be performed from an external device just
by turning on power to the robot controller.
Example: @AUTO
Switches to “AUTO” mode.
@RUN
Executes a program.
@READ PNT
7
All point data are read out.
RS-232C interface
@MOVE P,P123,SPEED=30
Moves to point 123 at 30% of maximum speed.
7-1
2. Communication function overview
There are 2 types of robot controller communication modes, “ONLINE” and “OFFLINE”.
7-2
3. Communication specifications
3.1 Connector
The RS-232C interface connector is located on the front panel of the robot controller as
shown below.
MOTOR
PWR MPB
OP.1 OP.3
RCX142
MODEL.
SRV SER. NO.
MANUFACTURED
XM ERR FACTORY AUTOMATION EQUIPMENT MADE IN JAPAN
ROB
I/O CAUTION
READ INSTRUCTION
MANUAL
XY
YM
COM BATT
ROB XY
I/O
ZR
ZR
5
9
OP.2 OP.4
RGEN
ZM
STD.DIO
P
SAFETY N
6
ACIN
1
RM
200-230V~
50-60Hz
MAX.2500VA
RS-232C interface
Pin No. Name Description Input/output
1 NC Not used
2 RXD Receive data Input
3 TXD Send data Output
4 NC Not used
5 GND Ground
6 NC Not used
7 RTS Request to send Output
8 CTS Permission to send Input
9 NC Not used
7-3
3. Communication specifications
n NOTE
1) Termination code
* For signal wire layout on the external device, refer to the instruction manual for that
device.
• CR (carriage return)
7 Robot transmission:
Adds a CR code (0DH) to the end
of a line. 3.2 Transmission mode and communication parameters
Robot receive:
RS-232C interface
7-4
3. Communication specifications
n The
NOTE
flow controls the functions
Transmits XOFF when available space
in receive buffer falls below a certain XON and XOFF are not transmitted.
separately. For instance, when all flow XON/XOFF capacity. XON and XOFF are ignored if received.
controls are set to “Yes” and the Transmits XON when receive buffer is
receive buffer capacity is low, an empty.
XOFF is transmitted, and RTS is
turned off. Later, when the receive Turns RTS off when available space in
buffer capacity is restored, an XON is receive buffer falls below a certain
transmitted, and RTS is turned on. RTS/CTS capacity.
Turns RTS on when receive buffer is
empty.
RTS is always on.
7
RS-232C interface
7-5
3. Communication specifications
1) The controller allows receiving data as long as the receive buffer has a free area.
The receive buffer is cleared in the following cases.
• When the power was turned off and turned back on.
• When the program was reset.
• When an ONLINE statement or OFFLINE statement was executed according to the
robot language.
• When the communication parameter was changed in “SYSTEM” mode or when
initialization was executed.
2) Turning on an external device might sent incorrect data to the robot controller which
is readying to receive data when the power is turned on. That incorrect data might
then be stored in the receive buffer if the controller is turned on prior to the external
device and cause communication errors.
In such a case,
• Reset the program before program execution.
• Clear the receive buffer by placing an ONLINE statement or OFFLINE statement at
the top of the program.
• Turn the external device on before turning the controller on.
3) When the external device does not support handshake protocols (BUSY control,
XON/XOFF control), the data processing speed becomes slower than the
communication speed, causing a communication error. In this case, take
countermeasures such as reducing the communication speed (baud rate).
7
4) When the communication speed is set at a high rate, communication errors might
occur due to external noise or other factors. In this case, take countermeasures such
RS-232C interface
7-6
3. Communication specifications
AC100 to 200V
FG
Connector metal parts
Potential
RS-232C interface
7-7
3. Communication specifications
HEX. 0- 1- 2- 3- 4- 5- 6- 7- 8- 9- A- B- C- D- E- F-
-0 SP 0 @ P p
-1 XON ! 1 A Q a q
-2 " 2 B R b r
-3 STO P XOFF # 3 C S c s
-4 $ 4 D T d t
-5 % 5 E U e u
-6 & 6 F V f v
-7 ' 7 G W g w
-8 BS ( 8 H X h x
-9 TAB ) 9 I Y i y
-A LF EOF * : J Z j z
-B + ; K [ k {
-C , < L \ l
7 -D CR - = M ] m }
-E . > N ^ n ~
RS-232C interface
-F / ? O o
7-8
Chapter 8 Specifications
Contents
1. Controller basic specifications ......................................................... 8-1
c CAUTION
• Specifications and appearance
Item Specifications
Memory size 364KB (Total of program and point data) (Available size for
program when maximum number of points is used: 84KB)
I/O input
Lithium battery (service life about 4 years at 0 to 40°C)
General-purpose 16 points, dedicated 9 points (NPN/PNP
8
STD. DIO specifications selectable)
I/O output General-purpose 8 points, dedicated 11 points
Specifications
Emergency stop input Relay contact
SAFETY 1 point (NPN/PNP specifications conform to STD.DIO
External I/O Service mode input setting.)
8-1
2. Controller basic functions
Function Description
AUTO mode (Major functions: program execution, step execution, etc.)
PROGRAM mode (Major functions: program creation and editing, etc.)
Operation modes MANUAL mode (Major functions: jog movement, point data teaching, etc.)
SYSTEM mode (Major functions: parameter editing, data initializing, etc.)
UTILITY mode (Major functions: motor power supply control, etc.)
Array declaration commands (DIM statement)
Assignment commands (Numeric assignment statement, character string
assignment statement, point definition, etc.)
Movement commands (MOVE, DRIVE, PMOVE statements, etc.)
Conditional branching commands (IF, FOR, WHILE statements, etc.)
Commands
External output commands (DO, MO, LO, TO, SO statements)
Parameter commands (ACCEL, OUTPOS, TOLE statements, etc.)
Condition wait command (WAIT statement)
Task related commands (START, SUSPEND, CUT statements, etc.)
etc.
Arithmetic functions (SIN, COS, TAN functions, etc.)
Character string functions (STR$, LEFT$, MID$, RIGHT$ functions, etc.)
Functions Point functions (WHERE, JTOXY, XYTOJ functions, etc.)
Parameter functions (ACCEL, OUTPOS, TOLE statements, etc.)
etc.
Simple variables (integer variables, real variables, character variables)
Array variables (integer variables, real variables, character variables)
Point variables
Variables Shift variables
Element variables (point element variables, shift element variables)
Input/output variables
etc.
Arithmetic operators (+, -, *, /, MOD)
Arithmetic operation Logic operators (AND, OR, XOR)
Relational operators (=, <, >, <>, <=, =>)
Monitor Input/output status monitor (200ms intervals)
8 Online commands
Key operation commands (AUTO, RUN, RESET, STEP, etc.)
Utility commands (COPY, ERA, INIT, etc.)
Data handling commands (READ, WRITE, ?VER, ?CONFIG, etc.)
Specifications
8-2
3. Robot controller external view
15.5
10.5
(204)
235
80.5
15.5
25 139.5 15.5
30
5.5 180 30 (20)
MOTOR
PWR MPB
OP.1 OP.3
RCX142
MODEL.
SRV SER. NO.
MANUFACTURED
XM ERR FACTORY AUTOMATION EQUIPMENT MADE IN JAPAN
ROB
I/O CAUTION
SANYODENKI
READ INSTRUCTION
MANUAL
XY
YM
COM BATT
265
290
ROB XY
I/O
250
ZR
ZR
OP.2 OP.4
RGEN
ZM
STD.DIO
P
SAFETY N
RM ACIN
200-230V~
50-60Hz
MAX.2500VA
10
5.5 5.5
44.8 100 27.6 180
(204)
235
8
15.5
Specifications
25 139.5 15.5
30
5.5 180 8 40 (20)
MOTOR
PWR MPB
OP.1 OP.3
RCX142 RGU-2
MODEL.
SRV SER. NO.
MANUFACTURED
XM ERR FACTORY AUTOMATION EQUIPMENT MADE IN JAPAN
ROB
I/O CAUTION SANYODENKI
CAUTION
READ INSTRUCTION
MANUAL
XY
ELECTRIC HAZARD
YM
RGEN
COM BATT
N
265
290
ROB XY P
I/O
250
ZR
ZR
OP.2 OP.4
RGEN
ZM
STD.DIO
P
SAFETY N
RM ACIN
200-230V~
50-60Hz
MAX.2500VA YAMAHA MOTOR CO.,LTD.
10
5.5 5.5
44.8 100 27.6 180
8-3
4. MPB basic specifications and external view
MPB basic specifications and external view
Model MPB
Power DC ±12V
Cable length 5m
F6 F7 F8 F9 F10
F 1 F 2 F 3 F 4 F 5
F11 F12 F13 F14 F15
DISPLAY
DISPLAY
<<
<<
<<<<
<< <<<<
<<
241
A
A B
B C
C D
D E
E
( ) % $ ! START
START STOP
STOP
FF G
G H
H II JJ
X #1-
K
K LL M
M N
N O
O
[ ] 7 8 9 #2+ Y #2-
P
P Q
Q R
R S
S TT
: ; 4 6
8
5 #3+ Z #3-
U
U V
V W
W X
X Y
Y
/ 1 2 3 #4+ R #4-
ZZ '' "" {{ ##
0 . , #5+ A #5-
?? }}
#6+
Specifications
UPPER
UPPER LOWER
LOWER SPACE
SPACE B #6-
28.6
101
189
8-4
Chapter 9 Troubleshooting
Contents
1. Error Messages ................................................................................. 9-1
1.1 Robot controller error messages ............................................................ 9-1
[ 0] Warnings and messages ............................................................................... 9-3
[ 1] Warnings (error history entry) ...................................................................... 9-5
[ 2] Robot operating area errors ......................................................................... 9-5
[ 3] Program file operating errors ....................................................................... 9-8
[ 4] Data entry and edit errors .......................................................................... 9-10
[ 5] Robot language syntax (compiling) errors .................................................. 9-11
[ 6] Robot language execution errors ............................................................... 9-18
[ 9] Memory errors ........................................................................................... 9-22
[10] System setting or hardware errors .............................................................. 9-24
[12] I/O and option board errors ....................................................................... 9-26
[13] MPB errors ................................................................................................ 9-30
[14] RS-232C communication errors ................................................................. 9-31
[15] Memory card errors ................................................................................... 9-33
[17] Motor control errors .................................................................................. 9-35
[21] Major software errors ................................................................................ 9-42
[22] Major hardware errors ............................................................................... 9-43
1.2 MPB Error Messages ............................................................................ 9-47
2. Troubleshooting.............................................................................. 9-49
2.1 When trouble occurs .......................................................................... 9-49
2.2 Acquiring error information ................................................................ 9-50
2.2.1 Acquiring information from the MPB ................................................... 9-50
2.2.2 Acquiring information from the RS-232C ............................................. 9-50
2.3 Troubleshooting checkpoints ............................................................... 9-51
MEMO
1. Error Messages
Message
Error classification No.
Error No.
Error group No.
n Messages
NOTE
for group No. 0 are not
[ 0] Warnings and messages
[ 7] (Not used)
[ 8] (Not used)
[ 9] Memory errors
[15]
[16]
Memory card errors
(Not used)
9
[17] Motor control errors Troubleshooting
[18] (Not used)
9-1
1. Error Messages
[Format]
Error No. : [<location where error occurred>,] error message
… Displays the error message on screen.
Code : … Displays the error code in hexadecimal numbers.
Meaning/Cause : … Displays the meaning and cause of the error.
Action : … Displays a message explaining action needed to eliminate
or avoid error status.
Dedicated output : … Refer to “(2) Dedicated output status”.
* The beginning of the error message may sometimes include information on the
location (axis, option unit, etc.) where the error occurred. An "M" in this
information indicates the main group axis No., an "S" indicates the sub group axis
No., a "D" indicates the driver axis No., and an "OP" indicates the option unit slot
No.
For example, a message "2.1:M1, Soft limit over" indicates that the preset soft limit
values have been exceeded on axis 1 of the main group robot. Likewise, the
message, "17.4:D2, Overload" indicates that an overload has occurred in axis 2 of
the driver unit. The axes viewed by the robot and the axes viewed by the driver are
normally a one-to-one match with each other, but when dual-drive axes are used,
one axis viewed by the robot may sometimes be treated as 2 axes by the driver.
(2) Dedicated output status
Dedicated output status items described below in *1 to *4 show the following contents.
*1 … CPU stop
• Turn the power ON again to reset.
DO 01a (CPU OK) = OFF
DO 02a (SERVO ON) = OFF
DO 03a (ALARM) = ON
*2 … Driver stop
• Turn the power ON again to reset.
DO 02a (SERVO ON) = OFF
DO 03a (ALARM) = ON
9 *3 … Servo stop
• Turn the power ON again in “UTILITY” mode to reset.
Troubleshooting
9-2
1. Error Messages
0.2 : Running
Code : &H0002
Meaning/Cause : Program or command is running.
Action : ---
0.4 : Compiling
Code : &H0004
Meaning/Cause : Robot language compiling (making an object program) is in
progress.
Action : ---
0.5 : Busy
Code : &H0005
Meaning/Cause : Data is being saved on a memory card or internal ROM.
Action : ---
9-3
1. Error Messages
9-4
1. Error Messages
9-5
1. Error Messages
9-6
1. Error Messages
9-7
1. Error Messages
9-8
1. Error Messages
9-9
1. Error Messages
Code : &H0401
Meaning/Cause : A point number was entered exceeding P9999.
Action : Input a correct point number.
9-10
1. Error Messages
9-11
1. Error Messages
9-12
1. Error Messages
9-13
1. Error Messages
9-14
1. Error Messages
9-15
1. Error Messages
9-16
1. Error Messages
9-17
1. Error Messages
9-18
1. Error Messages
6.3 : Division by 0
Code : &H0603
Meaning/Cause : A command to divide by 0 (÷ 0) was attempted.
Action : Change from the divide by 0 command.
9-19
1. Error Messages
9-20
1. Error Messages
9-21
1. Error Messages
[ 9] Memory errors
9-22
1. Error Messages
9-23
1. Error Messages
9-24
1. Error Messages
9-25
1. Error Messages
12.1 : Emg.stop on
Troubleshooting
Code : &H0C01
Meaning/Cause : a. Emergency stop button was pressed.
b. Emergency stop terminals on SAFETY connector are open
(emergency stop status).
c. MPB or terminator are not connected to MPB connector.
d. SAFETY connector is not connected.
Action : 1. Release the MPB emergency stop button.
2. Close the emergency stop terminals on SAFETY connector.
3. Connect MPB or terminator to MPB connector.
4. Attach the SAFETY connector.
Dedicated output : *3
9-26
1. Error Messages
12.2 : Interlock on
Code : &H0C02
Meaning/Cause : a. Program was executed or moving of axis attempted while
interlock signal was still input.
b. Interlock signal turned ON during execution of program or
axis movement.
c. DC 24V not supplied to STD.DIO connector.
d. STD.DIO connector is not connected.
Action : 1. Cancel the interlock signal, and execute program or move
axis.
2. Supply DC 24V to STD.DIO connector.
3. Connect the STD.DIO connector.
4. Disable the "DI (11) control" parameter when not using
STD.DIO.
9-27
1. Error Messages
Code : &H0C15
Meaning/Cause : a. Error in cable for PROFIBUS system.
b. The PROFIBUS system's station address setting is incorrect.
c. The master station PLC power is turned off, or the PLC has
stopped operating or is not operating correctly, or is broken.
d. Breakdown in PROFIBUS compatible unit.
Action : 1. Check for a break, misconnection or wiring error in
PROFIBUS cable, and check the specifications (cable length,
etc.)
2. Check the station address settings.
3. Check whether the master station PLC is operating correctly.
4. Check the hardware configuration settings.
5. Replace the PROFIBUS compatible unit.
9-28
1. Error Messages
9-29
1. Error Messages
9-30
1. Error Messages
9-31
1. Error Messages
9-32
1. Error Messages
9-33
1. Error Messages
Code : &H0F15
Meaning/Cause : Memory card not inserted correctly in slot.
Action : Insert the memory card correctly.
15.23 : Aborted
Code : &H0F17
Meaning/Cause : STOP key was pressed during reading/writing from or into
memory card, and the operation halted.
Action : ---
9-34
1. Error Messages
9-35
1. Error Messages
9-36
1. Error Messages
9-37
1. Error Messages
9-38
1. Error Messages
9-39
1. Error Messages
9-40
1. Error Messages
9-41
1. Error Messages
9-42
1. Error Messages
9-43
1. Error Messages
9-44
1. Error Messages
Action
3. Dual port RAM is defective.
: Replace the controller.
9
Dedicated output : *1 or *2 Troubleshooting
9-45
1. Error Messages
9
Troubleshooting
9-46
1. Error Messages
MPB TRAP!!
Contents : Undefined operation code was executed.
Cause : A hardware error occurred.
Action : Replace the MPB.
9-47
1. Error Messages
M P B Tr a n s m i t E r r o r ! ! ( T i m e O u t E r r o r )
Contents : Transmitting to controller is impossible.
Cause : a. The cable is broken or disconnected.
b. No response from controller due to problem in CPU unit.
Action : 1. Replace MPB cable.
2. Replace the MPB.
3. Replace the controller.
M P B R S - 4 2 2 E r r o r ! ! ( D ATA L I N E E r r o r )
Contents : Data communication with controllers is defective.
Cause : a. The cable is broken or disconnected.
b. The connector is not making contact.
Action : 1. Replace the MPB cable.
2. Replace the controller.
9 M P B M e m o r y E r r o r ! ! ( D ATA W r i t e E r r o r )
Contents : Internal memory is defective.
Troubleshooting
9-48
2. Troubleshooting
n When
NOTE
the MPB is connected, the error How often it happens
example: Always occurs when power is turned on.
Occurs at particular line during program operation.
message appearing on the screen is a
valuable source of information for
troubleshooting.
Only occurs once, then does not occur again.
9
Troubleshooting
9-49
2. Troubleshooting
3) Send “@READ LOG” from the PC to receive the internal error history in the robot
controller.
A maximum of 500 error histories can be checked.
9
Troubleshooting
9-50
2. Troubleshooting
9
Troubleshooting
9-51
2. Troubleshooting
2. Robot operation
9-52
2. Troubleshooting
3. I/O operation
• Problem in signal • Check wiring on standard I/O • Make the correct wiring on
connection. interface connector. standard I/O interface connector.
• Check wiring on option I/O • Make the correct wiring on
interface connector. option I/O interface connector.
• Error in option I/O • Check the option I/O interface • Make the correct option I/O
9
interface setting. setting on the DIP switch. interface setting. Troubleshooting
• Error has occurred. • Connect the MPB and check • Check the cause from the
the error information. error information.
• Check if “ERR” LED is lit on • Eliminate the cause of the
front of controller. error.
9-53
OPERATION MANUAL
Robot Controller
Dec. 2004
Ver. 1.00
This manual is based on Ver. 2.00 of the Japanese manual.