EML2322L Design & Manufacturing Laboratory

Fasteners

Table of Contents

I. Copyright Notice
II. Why Care?

1. Definitions
2. Common Fastener Types
3. Fastener Nomenclature
4. Fastener Thread Types
5. Rolled Threads vs. Cut Threads
6. Fastener Function
7. Over-tightening vs. Under-tightening
8. Calculating Proper Fastener Torque
9. Fastener Designations
10. Fastener Choices
11. Tap Drills / Holes
12. Clearance Drills / Holes
13. Fastener Joint Design
14. Application Examples

1
Copyright notice:

Much of the following material is taken from Carroll Smiths Nuts, Bolts,
Fasteners and Plumbing Handbook. This book contains a wealth of
knowledge concerning the proper selection and use of hardware used to join
components. It is available for ~ $20 and will save you thousands of dollars in
mistakes your first few years working industry. Translation: you would be
foolish to perform mechanical design without reading a copy of this book
from cover to cover! These notes attempt to establish a solid foundation and
provide references for further study.

Additional material and tables come from K. H. Moltrechts Machine Shop

Practice and Joseph E. Shigleys Mechanical Engineering Design textbooks.

Why you should care about these notes:

Fastener failures (due to improper design/selection or installation) are THE

NUMBER ONE cause of mechanical failures in industry. The topic is rarely
given the focus it deserves in the classroom for a variety of reasons, none of
which are acceptable. Consequently, this will likely be the most thorough
discussion of fasteners you will receive.

Virtually every mechanical assembly designed in industry makes use of

fasteners to attach components together to form systems.

2
1. Definitions

Fasteners are defined as hardware that can be easily installed and removed with hand
or power tools. Common fasteners include screws, bolts, nuts and rivets. The terms
bolts and screws do not refer to specific types of fasteners, but rather how they are
used (i.e. the application). Thus the same fastener may be termed a bolt or a screw.
Bolts are defined as headed fasteners having external threads that meet an exacting,
uniform thread specification such that they can accept a non-tapered nut. Screws are
defined as headed, externally-threaded fasteners that do not mate with a non-tapered
nut and are instead threaded into the material they will hold. As shown in figure 1, a
bolt joint can be defined as that which uses a bolt and nut assembly (inherently
requiring two tools to tighten or loosen) whereas a screw joint can be defined as one
in which a screw is mated into a matching female thread in a workpiece (therefore
only requiring one tool to tighten or loosen). As seen in figure 1, studs are a hybrid
between a bolt and a screw, since one end of the stud functions as a screw while the
other functions as a bolt.


Figure 1. Bolt, screw and stud applications.

2. Common Fastener Types

Figure 2 illustrates the variety of male fasteners used in industry; the most common
types are hex head, slotted head, flat (or countersunk) head, round head, socket (or
allen) head, button head and socket set screw. Figure 3 shows different female
fasteners (i.e. nuts) used in industry; the most common types are regular hexagonal
nuts and nylon ring elastic stop nuts (also known as lock nuts).

3
Figure 2. Male fasteners common in industry.

4
Figure 3. Female fasteners common in industry.

5
3. Fastener Nomenclature

Design engineers are frequently tasked with selecting and specifying fasteners used in
their designs. Consequently, understanding basic fastener nomenclature is important.
Figure 4 illustrates the different parts of a standard threaded fastener.

Figure 4. Important male fastener nomenclature.

A. major diameter the largest diameter of a fastener thread

B. minor diameter the smallest diameter of a fastener thread
C. pitch the linear distance from a point on the thread to a corresponding point on the next
thread measured parallel to the axis of the thread
D. lead the linear distance that a point on a fastener thread will advance axially in one
revolution (equal to the pitch of the fastener)
E. thread root the surface of the thread that joins the flanks of adjacent threads and is
immediately adjacent to the cylinder from which the thread projects; in other words, the
valley of the thread.
F. thread crest the surface of the thread that joins the flanks of the thread and is farthest
from the cylinder from which the thread projects; in other words, the peak of the thread.
G. head the enlarged shape that is formed on one end of the fastener to provide a bearing
surface and a method of turning (or holding) the fastener
H. bearing surface the supporting surface of a fastener with respect to the part it fastens

6
 I. point the extreme end of the threaded portion of a fastener
J. shank the cylindrical part of a fastener that extends from the underside of the head to
the starting thread
K. length the axial distance between the bearing surface of the head and the extreme point
L. grip length the length of the unthreaded portion of the fastener (i.e. shank) measured
axially from the underside of the bearing surface to the starting thread
M. thread length the length of the threaded portion of the fastener; NOTE: with all
commercial and aerospace fasteners, threaded length is a function of fastener diameter

4. Fastener Thread Types

In the most general sense, there are two classes of fastener threads: English and
metric. For each class, regardless of country of origin, there are two types of threads:
fine thread and coarse thread. The drill and tap chart summarizes this information in
one convenient location and will be referenced later in these notes.

One of the most common fastener mistakes is using the wrong type of thread in the
wrong type of material. The basic rule for fastener selection is: fine threads are
stronger when the female thread is strong relative to the male thread, and coarse
threads are stronger when the female thread is weak relative to the male thread.
The reason for this statement is that a smaller minor diameter increases the thread
area, resulting in higher static strength and fatigue resistance in female threads.
Conversely, a larger minor diameter increases the stress area, resulting in a higher
static strength and fatigue resistance in male threads. It is instructive to select a
fastener size off the tap chart and prove this statement; when performing the analysis,
assume stresses are distributed over only the first five engaged threads.
Figure 5 depicts a -20 fastener. Due to the elasticity of the fastener, only the first
five threads are engaged during loading regardless of the thread type (coarse / fine).
Female threads typically fail due to shear along the major diameter and male threads
typically fail due to tensile loading along the thread root.

7
 Figure 5. Thread engagement and fastener failure.

Since five threads carry the entire load regardless of thread type, a decrease in the
minor diameter increases the shear area and gives an advantage to the female threads
while reducing the load carrying capability of the male fastener. Conversely, an
increase in the minor diameter increases the male fasteners cross-sectional area and
gives an advantage to the male fastener, however, this reduces the shear area and
weakens the female threads. Therefore, if the female fastener material is weak
compared to the male fastener material, the female fastener should be given the
advantage and coarse threads should be chosen. If the female fastener material is
strong compared to the male fastener material, the male fastener will always fail first
and should consequently be given the advantage by selecting fine threads.

For this reason steel bolts and studs that thread into relatively weak aluminum or cast
iron castings such as engine blocks, cylinder heads and gearboxes are always coarse
threaded on the end that goes into the casting. Also invariably, the end of the stud that
receives the nut is provided with a fine thread. In this way the designer ends up with
the best of both worlds.

Because coarse threads are faster to assemble, they are often used in applications
where strength and weight are not of utmost concern. Conversely, virtually all
aerospace bolted assemblies feature fine threads. Generally, unless threading into a
relatively weak material, avoid coarse threaded fasteners.

8
5. Rolled Threads Versus Cut Threads
All quality fasteners have rolled threads produced via rolling or sliding dies as seen in
figure 6 or in this video on fastener manufacturing. Rolled threads (as opposed to
threads cut on a lathe, with a cutting die or tap) produce superior surface finish (thus
lower stress risers) and improved material properties from cold working the material,
resulting in much higher fatigue resistance. Rolled threads increase thread strength by
a minimum of 30% over well-cut threads.1


Figure 6. Rolled threads.
As illustrated in figure 7, when a thread is cut into a specimen, the grain flow of the
material is severed. When a thread is rolled into a specimen, however, the grain flow
of the material remains continuous and follows the contour of the thread. For this
reason, rolled threads better resist stripping because shear failures must take place
across the material grain rather than with it.


Figure 7. Cut vs. rolled thread grain flow.

1
EBC Industries
9
As seen in figure 8, another benefit of thread rolling is it produces a much better
surface finish than thread cutting. The surface factor plot presented in figure 9
illustrates the relationship between stress concentrations and surface finish, which
clearly shows that on high strength fasteners, rolled threads possess up to twice the
fatigue resistance compared to cut threads.


Figure 8. Cut vs. rolled thread surface finish and thread profile.


Figure 9. Surface finish modification factor as a function of fastener strength
for rolled (polished) and cut (machined) threads.

10
Rolling also leaves the surface of the threads, particularly in the roots, stressed in
compression. These compressive stresses must be overcome before the tensile
stresses can reach a level that will cause fatigue failures. Compressive surface stresses
also increase root hardness, further adding to the part's fatigue resistance.

Improved fatigue strength resulting from the above factors is reported to be on the
order of 50% - 75%. On heat-treated bolts from Rockwell C36 to 40 hardness that
have threads rolled after heat-treatment, tests show increased fatigue strength of 5 to
10 times that of cut threads.
Now consider the effect of heat-treatment on the final thread profile. All quality
fasteners must be heat-treated to achieve the desired strength and toughness. The
heat-treatment process inevitably results in some physical distortion of the fastener
blank. Rolling the thread onto the (already) heat treated blank ensures the thread will
be coaxial with the bolt and normal to the bearing surface of the fastener head, which
is critical for proper function. Finally, due to the speed at which fastener threads can
be rolled onto a blank with the proper equipment, rolled threads can actually be more
economical to manufacture in larger quantities.

11
6. Fastener Function
Fasteners have only ONE intended function: to clamp parts together. Fasteners
are not meant to position parts relative to one another; that is the function of dowel
pins (figure 10), locating shoulders and piloting diameters. Additionally, fasteners are
not meant to function as pivots, axles and fulcrums; pins appropriately serve this
function. (Note: students often get away with using fasteners to locate parts on the
designs in this course because of the light duty, short-term use of the project and
convenience of doing so; in use these bolted connections will loosen, causing the
assembly to fail. This problem is avoided by regularly checking for loose fasteners
prior to testing.)

Figure 10. Proper use of dowel pins to position parts and resist shear forces.

More importantly, the threaded portion of a fastener should NEVER be loaded in

shear for at least three reasons. First, the threaded portion of the fastener is of slightly
smaller diameter than the unthreaded shank, allowing the fastener to quickly loosen if
transverse loading is applied (and dowel pins are not appropriately used to resist the
shear stresses). Second, the threaded portion of the bolt has much less surface area
than the shank (figure 11), which means it offers significantly less bearing area to the
joint; this reduces the load carrying capacity and fatigue resistance of the assembly.
Third, when (not if!) the relative motion between the hole and the loose fitting
threaded portion of the bolt occurs, the thread will act as a low speed file, removing
material from the inside of the hole, exacerbating the problem. So good design
engineers NEVER load fastener threads in shear.

12
 Figure 11. Never place fastener threads in shear; use dowel pins when possible
and place the shank in shear when necessary.

7. Over-tightening vs. Under-tightening

As design engineers, each of us is ultimately responsible for the success or failure of
the components and systems we design. When it comes to fasteners, it is important to
understand the consequence of over-tightening versus under-tightening fastener joints.
Un-intuitively, it is actually better to over-tighten a bolted joint than to under-tighten
it! To explain this statement, it is helpful to review a common stress-strain curve for a
typical fastener material, as shown in figure 12.

For those who have not taken a materials course, stress is a measure of how much
tensile load is placed on the fastener and strain is a measure of the fasteners change
in length (i.e. stretch). As seen in figure 12, there is a linear (elastic) region in
which the fastener will return to its original length when the load is relaxed. The yield
strength denotes the point (or magnitude) above which the material yields or
permanently deforms. As additional load is placed on the fastener beyond the onset of
yield, the strength actually increases as the material undergoes strain hardening, to the
maximum (or ultimate) stress point. Beyond the ultimate tensile strength, the
material begins to neck (which is a local reduction of cross sectional diameter) and
finally fails at the point of fracture.

13
 Figure 12. Stress versus strain plot for alloy steel.

The following example is taken from Carroll Smiths Nuts, Bolts, Fasteners and
Plumbing Handbook. A 3/8" diameter bolt with an ultimate tensile strength (UTS) of
180,000 psi is torqued to 40% of its UTS (72,000 psi) and subjected to a cyclic
tension load of 12,000 lbf using an Instron testing machine (figure 13). The 3/8" bolt
will endure 4,900 force application cycles before failure. Next, an IDENTICAL bolt
is torqued to 60% of its UTS (108,000 psi) and subjected to THE SAME cyclic
tension load of 12,000 lbf. This identical bolt will endure 6,000,000 force application
cycles before failure, or roughly 1000 TIMES more stress cycles (or service life).

The previous example demonstrates the necessity for engineers to specify the
correct installation torques of all fasteners used in critical assemblies. At the end
of the day, PROPER INSTALLATION TORQUE (I.E. FASTENER TENSILE
PRELOAD) IS WHAT KEEPS A PROPERLY DESIGNED FASTENER
ASSEMBLY TIGHT. Contrary to popular misbelief, so called lock washers
do not keep fastener joints tight; anaerobic adhesives (such as Loctite) do not
keep fastener joints tight; safety wire does not keep fastener joints tight, elastic
stop nuts will not keep fastener joints tight, nor will castellated nuts and cotter
pins. Several of these will help prevent a loosened fastener from falling off
completely for a limited time, but NONE are a replacement for a properly
designed and torqued (i.e. preloaded) fastener joint.

14
 
Figure 13. Tensile testing to measure number of cycles before fastener failure.

8. Calculating Proper Fastener Torque

The previous section illustrates the importance of specifying the tightening torque for
mission critical fasteners; this section explains how to do so and is therefore one of the
most useful pieces of information you can take away from this course, so please
review it carefully. Equation 1 relates desired fastener preload (or tension) to the
installed (or measured) fastener torque:

T 0.2 Fi d (Eq. 1)

where T is the measured installation torque (measured with a torque wrench)

Fi is the desired preload (installed tensile force in the bolt)
d is the nominal bolt (shank) diameter

Equation 1 assumes a coefficient of friction () of 0.15, which is average and varies

based on lubricant and fastener plating. This simple equation results in approximately
80% accuracy, which is within the tolerance of most fastener specifications. On
critical fastener installations, the desired preload (tensile stress) for optimum
performance is equal to the yield (or proof) strength. To allow for a conservative
margin for error, aim for an installed tensile stress (t) equal to approximately 90% of
the ultimate yield strength (y):

t 0.9 y (Eq. 2)
15
Example 1: calculate the proper tightening torque (lbf-ft) of a grade 5, 3/8-16 bolt:

from Table 7-5: y = 85,000 psi

from equation 2 we desire: t 0.9 y = 76,500 psi

since the installed tensile stress is equal to the bolt preload (Fi) divided by the
tensile stress area (At), we can write:
t = Fi / At
for a 3/8-16 fastener thread, Table 7-1 gives At = 0.0775 in2
therefore Fi = t At = 76,500 psi 0.0775 in2 = 5929 lbf
now calculate the tightening torque, T using equation 1:
T 0.2 Fi d = 0.2 5929 lbf 0.375 in = 444 lbf-in = 37 lbf-ft (answer)

For a real design a first approximation of bolt size would be obtained by defining the
factor of safety as:

n = Fi / P
Then the bolt size is determined such that its preload is larger than the external tensile
load by the amount of the factor of safety.

16
17
18
Once the required torque is calculated, the final step is ensuring it is achieved, which
is performed by either measuring the torque on the fastener during installation (figure
14) or by measuring how much the fastener stretches after installation (figure 15).

Figure 14. Types of wrenches used to measure fastener installation torque/preload.

Figure 15. Measuring bolt strain (stretch) to verify proper preload.

19
9. Fastener Choices
The only fastener choices available off the shelf (OTS) are those listed on the drill
and tap chart. These are THE ONLY options available to design engineers when
selecting fasteners, as anything else would require prohibitively expensive custom
tooling and fasteners. So ALWAYS reference a tap chart when selecting fasteners.

10. Fastener Designations

In general, fasteners are referred to by their shank size (i.e. a " or a 12mm fastener).
Standard (inch) fasteners are referred to by their shank size and the number of threads
per inch they possessfor example 3/8"-16 or "-20, and are pronounced three-
eighths sixteen or one-half twenty. Standard (inch) fasteners which are " and
larger are referred to by their nominal shank size. Fasteners smaller than " are
referred to by screw size designations, such as number 10 or number 6. Metric
fasteners are referred to by their shank size and thread pitchfor example M6x1.0 or
M10x1.5, and are pronounced metric six by one or M ten by one point five.

11. Tap Drills / Holes

The term tap drill refers to the final drill size used to make a properly sized hole prior
to using a tap (internal threading tool) to cut threads into the hole. Note every tap drill
is a standard drill, but not every standard drill is a tap drill. The size of the tap drilled
hole is critical for each fastener and must be obtained from a tap chart like the one
provided in this course or found in the Machinery Handbook. If this hole size is too
small the tap will break when trying to create the threads; if the hole size is too large,
the threads will be weak and fail (shear) in service. Note the tap drill size listed on the
tap chart for a particular thread depends on the material type (weak or strong).

12. Clearance Drills / Holes

Clearance drills are used to create exactly what the name implies: clearance holes for
fasteners, shafts or pins. Industry standards for clearance holes are listed in the last
column of the drill and tap chart. Note there are only two options for each size
fastener: a close fit or free fit. Close fit clearance holes are used when you want a
more accurate bolt pattern (i.e. when using the DRO on the milling machine) and free
fit clearance holes are used when you want to save time and make the clearance holes
more quickly (i.e. when using a drill press). Clearance hole sizes listed on the tap
chart are industry standards every manufacturing facility will stock and should always
be used unless you have a very good reason to deviate.
20
13. Fastener Joint Design
When designing fastener joints, always design the most stable joint that provides
the greatest bearing area. As an example, consider the common shear joint design
shown below in figure 16. The joint design is said to be in single shear if the fastener
would only need to shear in one plane for the joint to fail; whereas the joint design is
said to be in double shear if the fastener would need to shear in two planes for the
joint to fail. Obviously the double shear mount is stronger and more stable than the
single shear mount, and should be used at every available opportunity when joint
strength and reliability are of concern. In fact, in the great words of the late Carroll
Smith: [when it comes to weight conscious, mission critical designs] the single shear
mount in a crime against nature and a perversion of the bad engineer!

Figure 16. Single shear versus double shear joint design.

Another important rule for fastener joint stability is to never place fastener holes
closer than one major diameter to a workpiece edge, as doing so does not leave
adequate material to resist the bearing stress. As shown in Figure 16 above, the hole
locations in each workpiece provide the minimum amount of required material for the
fastener joint, resulting in the lightest design which does not compromise strength.

21
14. Application Examples

Example 1: You are tasked with designing a motor mount that will attach via -20
fasteners to 80/20 aluminum extrusion. The tolerances are loose (0.125"), the loads
are light, and assembly time is important. What hole callout should you use to specify
the two thru clearance holes for the -20 fasteners?

Answer 1: Since assembly time is of concern, tolerances are loose, and loads are
light, free fit clearance holes are the correct design choice.
The hole callout format is:
free fit drill diameter + depth;
quantity of holes desired (not included if only one hole is specified)
From the drill and tap chart, the hole specification is:

0.266" THRU;
2 PLACES

Example 2: You are tasked with designing a motor mount that will attach via 10-32
fasteners to a motor with a four hole bolt pattern. Assembly time is at a premium but
accuracy is necessary for part function. What hole callout should you use to specify
the thru clearance holes for the 10-32 fasteners?

Answer 2: Since the motor mount will be mating with an existing bolt pattern (which
will be precise), a close fit hole specification should be used. However, a free fit hole
would be best for reducing assembly time. Since the part requires high accuracy,
regardless of the additional time it takes to create a close fit hole pattern, a close
fit hole pattern is required.
The clearance hole callout format is:
close fit drill diameter + depth;
quantity of holes desired (not included if only one hole is specified)
From the drill and tap chart, the hole specification is:

0.196" THRU;
4 PLACES

22
Example 3: You need to specify the hole callout for three threaded (i.e. tapped)
holes through an aluminum part. 6mm metric screws will mate with the part. How
should you specify the hole callout?
Answer 3: Since the material is aluminum (which is relatively soft and weak
compared to high strength steel fasteners), coarse threads should be specified.
The tapped hole callout format is:

tap drill diameter + depth;

thread specification + depth;
quantity of holes desired (not included if only one hole is specified)
From the drill and tap chart, the hole specification is:

5.00 THRU;
M6x1.0 THRU;
3 PLACES

Example 4: You need to specify the hole callout for four tapped holes through a steel
bracket. Five metric fasteners of size 4mm will mate with these holes. How should
you specify this hole?
Answer 4: Knowing the workpiece is steel (which is relatively strong), fine threads
should be specified for maximum joint strength.
The tapped hole callout format is:

tap drill diameter + depth;

thread specification + depth;
quantity of holes desired (not included if only one hole is specified)
From the drill and tap chart, the hole specification is:

3.50 THRU;
M4x0.70 THRU;
4 PLACES

23
Example 5: You are asked to specify the hole callout for a single tapped hole through
a steel wheel hub. A standard size 10 fastener will mate with this hole. How should
you specify the hole callout?
Answer 5: Knowing the workpiece is steel (which is relatively strong), fine threads
should be specified for maximum joint strength.
The tapped hole callout format is:

tap drill diameter + depth;

thread specification + depth;
quantity of holes desired (not included if only one hole is specified)
From the drill and tap chart, the hole specification is:

0.170 THRU;
10-32 UNF THRU

Example 6: You are asked to specify the hole callout for six screw holes through an
aluminum part. Six standard fasteners of size 3/8" will mate with these holes. How
should you specify the hole callout?
Answer 6: Since the material is aluminum (which is relatively soft and weak
compared to high strength steel fasteners), coarse threads should be specified.
The tapped hole callout format is:
tap drill diameter + depth;
thread specification + depth;
quantity of holes desired (not included if only one hole is specified)

From the drill and tap chart, the hole specification is:

0.313 THRU;
3/8-16 UNC THRU;
6 PLACES

24
Example 7: Specify seven holes tapped half way through a 1" part for use with 10-24
screws.

Answer 7: Although the material is not specified, you should be able to recognize the
part is a weak material (such as aluminum or a casting) OR emphasis is placed on
reducing assembly time at the expense of joint strength and / or weight.
The tapped hole callout format is:

tap drill diameter + depth;

thread specification + depth;
quantity of holes desired (not included if only one hole is specified)
Notice that when working with blind threads (i.e. not thru) you must drill an
additional screw diameter ( 0.190") beyond the desired thread depth. From the drill
and tap chart, the hole specification is:

0.157 0.7 DEEP;

10-24 UNC 0.50 DEEP;
7 PLACES

Example 8: Specify the hole callout for one 5/8" screw thread through an aluminum
bracket and calculate the minimum part thickness to ensure proper thread strength.
Answer 8: Since the material is aluminum, coarse threads should be specified.

The tapped hole callout format is:

tap drill diameter + depth;
thread specification + depth;
quantity of holes desired (not included if only one hole is specified)

From the drill and tap chart, the hole specification is:

0.531 THRU;
5/8-11 UNC THRU

( problem is continued on next page >> )

25
Since a MININUM of five threads must be engaged for a fastener joint to achieve full
strength, the required workpiece thickness can be determined using the thread pitch
(11 TPI in this case) and basic unit analysis:
5 threads (11 threads/in) -1 = 5/11 in

Therefore, the workpiece must be greater than 0.455" thick for proper strength.

Example 9: If you have two 16GA (gauge) steel sheetmetal parts that must be
fastened together how would you design the fastener joint and what hole callouts
should you specify for the mating pieces?
Answer 9: 16GA steel sheetmetal has a thickness of ~0.060". Five full threads of
engagement are needed if the sheetmetal is going to be tapped. By unit analysis:
5 threads / 0.060 in = 83 threads/in

Since no fastener on the drill and tap chart has 83 threads per inch or more, threading
the sheetmetal is NOT a viable option. Therefore, thru holes should be specified in
both parts for use in a bolted assembly (i.e. fasteners that mate with nuts). The size of
the fastener is not specified and is a free design parameter. We choose a 10-32 UNF
arbitrarily (no other design information is given). Note the fine thread option is
selected to maximize the strength of the bolted assembly.

The clearance hole callout format is:

clearance drill diameter + depth;
quantity of holes desired (not included if only one hole is specified)

Depending on whether the design calls for close or free fit clearance holes (not enough
information is given), find the required hole size using the drill and tap chart:

0.196" THRU OR 0.201" THRU_

Alternatively, rivets could be used to semi-permanently join the two parts; however
more work would be required to remove the rivets if the components required
disassembly in the future.

26