AGMA Webinar Series

Analytical Gear Chart Interpretation:

Solving Manufacturing Problems
PART TWO

Dwight Smith
President, Cole Mfg. Systems, Inc.

June 7, 2012
Dwight Smith
Dwight Smith, President of Cole Mfg. Systems, Inc.,
has a wide range of experience in gear manufacturing,
workholding, metrology, analysis, and project
management.

He has been developing and presenting the Gear Basic

training sessions throughout North America since
1989. Smith serves as chairman of the AGMA
Nomenclature Committee and is an instructor for the
Basic Gear School for AGMA.

His company, Cole Mfg. Systems, Inc., represents

complementary gear-related equipment
manufacturers.

American Gear Manufacturers Association

 Chart Interpretation : Part 2

1. Some Things to Consider

2. Pitch Errors
3. Helix Errors
4. Profile Errors
5. Brief Overview of Several Gear
Standards
Things to Consider When Interpreting Gear
Inspection Charts

Errors occur outside of the analyzed area.

Errors can occur between the measured teeth.

Special Situations
Burrs
Improper Undercut
Short Involute
Broaching Tears
Special Situations: Burrs

A burr on the end of the tooth This end of the

may be outside the analyzed tooth does not
zone. have a burr.
 Special Situations: Improper Undercut

Proper undercut will appear Plus material below the

on the chart as minus SAP indicates improper
material. undercut, possibly a
damaged or worn hob.
 Special Situations: Short Involute

Proper involute length or minimum When the involute trace falls off prior to
chamfer diameter falls off beyond end the end of analysis, it indicates a tooth
of analysis. that is shorter than specified.
 Special
Situations:

Broaching
Special Situations:

Broaching
Understanding Pitch Errors
 Correcting
Radial
Runout

Relocate part on
inspection arbor

Correcting
Helix
Variation
(wobble)
Cumulative
Pitch

vs.

Single Pitch
Cumulative Pitch (index) with Radial Runout
Data Calculated From Pitch Data
Non-Hunting Tooth Pattern

Three start hob cutting a 30 tooth gear.

Understanding Helix Errors
 Helix
Variation
Helix Variation
 Helix Variation

It is impossible for the tool to cause helix

variation.

It is in all cases caused by axial wobble.

If you use helix average values for tolerances,

you need to consider variation as well.
Helix Angle Deviation and Form Deviation
Helix Form Deviation: Cause?
In Tolerance Helix Chart Hobbed Part
Helix Chart Variation and Form Deviation
Helix Chart Variation and Form Deviation
Helix Chart Taper
Helix Chart Variation and Form Deviation
Understanding Profile Errors
Profile Chart Overview
OD Variation
from Runout
Profile Form Deviation
Profile Chart
Profile Form Deviation Cause?
Profile Form Deviation Cause?
 Involute Error Patterns

Plus slope (balance) Very rough and irregular Form error

Both flanks surface similar pattern RF and
LF

Tears from broaching

 Involute Form Waviness

Problem:
Involute Waviness on right
flank

Potential Cause:
Loose/worn outboard
bearing assembly on hob
head

Fix:
Tighten/replace outboard
bearing
Involute Form Waviness
Involute Form Deviation

Problem:
Plus material near root

Cause:
Excessive wear on hob cutter
teeth after only 50 pieces.
Cutter probably not
completely sharpened.

Fix:
Resharpen or scrap hob cutter
Pitch, Helix and Profile Charts
Surface Finish
Measurement
 Factors Influencing Gear Quality

Common Variables that Influence all processes

Hob, shave, roll, broach, tool sharpening and measurement
Workpiece spindle tooling
Axial runout or wobble
Radial runout or eccentricity
Repeatability of mounting accuracy
Tool spindle and bearings
Radial and Axial Runout
Backlash
Tool maintenance and tool mounting
Contribution to Errors: Machine vs. Tool
Hobbing machine
Number of teeth
Root diameter
Tooth size or thickness
Index
Pitch
Helix angle (lead)
Wobble (lead variation)
Taper, crown
Profile form
Pitch diameter runout
Scallop pattern
depth and variation
Hobbing Tool
Profile angle
Profile modifications
Tip chamfer
Undercut
 Troubleshooting Gear Errors

Gear Characteristics Inspection Possible root Corrective

Element chart cause action
Category appearance

Hobbed/checked off Verify tooling

center (radial runout)

Runout Verify Master

Possible
Total Composite contamination

Tooth to Tooth
Profile error Check for involute
Nicks error

Mesh interference Check for plus tip

 Troubleshooting Gear Errors
Gear Characteristics Inspection Possible root Corrective
Element chart cause action
Category appearance

Helix Input correction Input correction

needed on machine
Slope (Angle)
error
Chips on fixture or Verify axial runout
Variation workholding of fixture
(wobble) misaligned (axial wear
runout)
Form or Inspect cutter
waviness Chips on cutter edge Verify
Cutting force to high workholding
rigidity
 Troubleshooting Gear Errors
Gear Characteristics Inspection Possible root Corrective
Element chart cause action
Category appearance

Involute Hob rake angle error Check hob

sharpening
(profile)
Angle (slope)
error Check workpiece
Radial runout of gear and fixture runout

Variation Cutter mounting error Check hob

(runout) mounting and
quality
Form or Excessive finish stock Check stock
waviness Worn tool removal amount
 Troubleshooting Gear Errors

Gear Characteristics Inspection Possible root Corrective

Element chart cause action
Category appearance

Runout of production Verify

fixture or inspection workholding
arbor
Pitch
(symbol fp)
Pitch Inspect hob for
Thread error on hob thread error
(index) Index (total
accumulated
pitch error-
symbol Fp) Wear or chips on Clean chips off
broach bar broach
 Troubleshooting Gear Errors
Gear Characteristics Inspection Possible root Corrective
Element chart cause action
Category appearance

Tooth Tapered hob Check hob for

proper quality
thickness
Heat causing
Size over pins
machine growth
or balls Monitor cutting oil
temperature
Hob swivel angle
error
Relative tooth
thickness Adjust hob swivel
angle for correct
size over pins
(DOB or DOP)
Gear Analysis Standards

AGMA 2000-A88 (Q)

AGMA 2015 (A)

ISO 1328

DIN 3960
Gear Analysis Standards

JIS

JGMA

France, Australia, Italy, UK

CAT

GM, Ford, Eaton, Honda, etc.

 Gear Analysis Standards
AGMA 2000-A88 AGMA 2015 DIN ISO

Allows use of "Design Profile" X X

Allows use of "Design Helix" X X

Total Deviation X X X
Angle Deviation X X X
Form Deviation X X X

Smooth Tolerance Curve X X

Optional Band Fit Analysis X

Bands Straight or Curved X

Steppped Tolerance Curves X X

Requires Band Fit Analysis X

Gear Analysis Standards - AGMA 2000-A88

AGMA 2000-A88
Gear Analysis Standards
DIN, ISO, AGMA 2015
Gear Analysis Standards - AGMA 2015

AGMA 2015-1-A01
 Comparing Gear Analysis Standards
DIN, ISO, AGMA 2015

Description ISO DIN AGMA 2015

Cumulative Pitch Deviation Fp Fp Fp

Difference Between Adjacent
Pitch Measurements fu
Single Pitch Deviation fpt fp fpt
 Comparing Gear Analysis Standards
DIN, ISO, AGMA 2015

Description ISO DIN AGMA 2015

Helix Deviation, Total F F F

Helix Slope Deviation fH fH fH
Helix Form Deviation ff ff ff
(DIN calls it Tooth Trace)
Helix Crown Cb
 Comparing Gear Analysis Standards
DIN, ISO, AGMA 2015

Description ISO DIN AGMA 2015

Profile Deviation, Total F F F

Profile Slope Deviation fH fH fH
(DIN calls it Profile Angle)
Profile Form Deviation ff ff ff
 Thank You!
Dwight Smith
Cole Mfg. Systems, Inc.

dsmith@colemfgsystems.com

Office: 248-601-8145 Mobile: 734-516-1365

If You Missed an AGMA Webinar
Visit AGMA Webinar Series Archive at www.agma.org

These are just a few of the archived programs available

Charting the Course Through Profound Demographic Change

Kenneth W. Gronbach

Design and Development Procedure for High-Precision Molded Plastic Gear

Transmissions
Dave Sheridan

Introduction to Gear Rating Suite 3.0

John Rinaldo

Analytical Gear Chart Interpretation: Reading Between the Lines

Dwight Smith

American Gear Manufacturers Association

AGMA 2012 - Education Calendar

January 24-26 Gearbox CSI: Forensic Analysis of Gear & Bearing Failures, Concordville, PA

April 16-20 Basic Training for Gear Manufacturing, Chicago, IL

May 15-17 Gear Materials - Selection, Metallurgy, Heat Treatment, and Quality Control, Milwaukee, WI

June 11-13 Gear Failure Analysis, Big Sky, MT

June 19-21 Gearbox System Design: The Rest of The StoryEverything But The Gears and Bearings,
Clearwater Beach, FL

Sept 17-19 Gear Failure Analysis, Big Sky, MT

Oct 1-5 Basic Training for Gear Manufacturing, Chicago, IL

Nov 13-15 Gear Manufacturing & Inspection Methods, Practices, Application & Interpretation for the
Design Engineer, Las Vegas, NV - MM

Dec 4-6 Detailed Gear Design Beyond Simple Service Factors (Not for the Faint-Hearted! Alexandria, VA

Visit www.agma.org for full details and registration.

American Gear Manufacturers Association