E1102m PDF

Rolling Bearings
Rolling Bearings
CAT. No. E1102m 2013 C-11 Printed in Japan NSK Ltd. First edition published in MAR. 2005
2013/10/16
Page No.
Tech.
Technical Information A7 Info.
Deep Groove Ball Brgs. B4
Angular Contact Ball Brgs. B46
Self-Aligning Ball Brgs. B76
Cylindrical Roller Brgs. B84
Tapered Roller Brgs. B110
Spherical Roller Brgs. B182
Thrust
Thrust Brgs. B206 Brgs.
Needle Roller Brgs. B244
Ball Brg. Units B280
Plummer Blocks B304
Cylindrical Roller Brgs. for Sheaves B326 Sheaves
Roll-Neck Brgs. (4-Rows) Roll Neck

B334 Railway
Railway Rolling Stock Brgs.
Balls and Rollers B346
Sleeves
Accessories for Rolling Brgs. B356
NSK Products and Appendices C1 Appendices
mikaesiE.indd 1-2 11/20/13 4:48:42 PM

Rolling Bearings
CAT. No. E1102m
A001-005E.indd 1 11/20/13 4:49:05 PM

Introduction to Revised NSK Rolling Bearing Catalog
(CAT.No.E1102m)
We want to thank you for your interest in this edition of our Rolling Bearing Catalog.
It has been revised with our customers in mind, and we hope it fills your needs.
Recently, technology has been advancing at a remarkable pace, and with it has
come a host of new products in many fields including computers, office automation,
audio-visual equipment, medical equipment, and many others. Accordingly, rolling
bearings, which are highly important machine elements, must be designed to satisfy
increasingly stringent requirements for higher speeds, greater precision, higher
reliability, and other challenging demands.
We edited this Rolling Bearing Catalog to reflect the growing number of NSK
products, new developments, and technical progress. In it, you will find a wide range
of bearings that will satisfy almost any requirement.
This catalog was revised to reflect the growing number of NSK products and
certain revisions in JIS and ISO and to better serve our customers. The first part
contains general information about rolling bearings to facilitate selection of the most
appropriate type. Next supplementary technical information is provided regarding
bearing life, load ratings, limiting speeds, handling and mounting, lubrication, etc.
Finally, the catalog presents extensive tables containing most bearing numbers
and showing dimensions and pertinent design data listed in the order of increasing
bore size. Data in the table are given in both the international Unit System (SI) and
Engineering Unit System (Gravitational System of Units).
We hope this catalog will allow you to select the optimum bearing for your
application. However, if assistance is required, please contact NSK, and the
companys engineers and computer programs can quickly supply the information
you need.
NSK Web site A http://www.nsk.com
A001-005E.indd 2-3 11/20/13 4:49:06 PM

CONTENTS
TECHNICAL INFORMATION
Pages Pages Pages Pages
1 TYPES AND FEATURES OF ROLLING 5.4 Equivalent Load A30 10.3 Preload and Rigidity A96 14.6 Maintenance and Inspection A124
BEARINGS A 7 5.4.1 Calculation of Equivalent Loads A31 10.3.1 Position Preload and Rigidity A96 14.6.1 Detecting and Correcting
1.1 Design and Classification A 7 5.4.2 Axial Load Components in Angular 10.3.2 Constant-Pressure Preload and Irregularities A124
1.2 Characteristics of Rolling Bearings A 7 Contact Ball Bearings and Tapered Rigidity A97 14.6.2 Bearing Failures and
Roller Bearings A31 10.4 Selection of Preloading Method and Measures A124
2 BEARING SELECTION PROCEDURE A16 5.5 Static Load Ratings and Static Equivalent Amount of Preload A97
Loads A32 10.4.1 Comparison of Preloading 15 TECHNICAL DATA A126
3 SELECTION OF BEARING TYPE A18 5.5.1 Static Load Ratings A32 Methods A97 15.1 Axial Displacement of Bearings A128
3.1 Allowable Bearing Space A18 5.5.2 Static Equivalent Loads A32 10.4.2 Amount of Preload A98 15.2 Fits A130
3.2 Load Capacity and Bearing Types A18 5.5.3 Permissible Static Load Factor A32 15.3 Radial and Axial Internal Clearances A132
3.3 Permissible Speed and Bearing Types A18 5.6 Maximum Permissible Axial Loads for 11 DESIGN OF SHAFTS AND HOUSINGS A100 15.4 Preload and Starting Torque A134
3.4 Misalignment of Inner/Outer Rings and Cylindrical Roller Bearings A33 11.1 Accuracy and Surface Finish of Shafts 15.5 Coefficients of Dynamic Friction and
Bearing Types A18 5.7 Examples of Bearing Calculations A34 and Housings A100 Other Bearing Data A136
3.5 Rigidity and Bearing Types A19 11.2 Shoulder and Fillet Dimensions A100 15.6 Brands and Properties of Lubricating
3.6 Noise and Torque of Various Bearing 6 LIMITING SPEED A37 11.3 Bearing Seals A102 Greases A138
Types A19 6.1 Correction of Limiting Speed A37 11.3.1 Non-Contact Types Seals A102
3.7 Running Accuracy and Bearing Types A19 6.2 Limiting Speed for Rubber Contact Seals 11.3.2 Contact Type Seals A104
3.8 Mounting and Dismounting of Various for Ball Bearings A37
Bearing Types A19 12 LUBRICATION A105 BEARING TABLES
7 BOUNDARY DIMENSIONS AND IDENTIFYING 12.1 Purposes of Lubrication A105
4 SELECTION OF BEARING ARRANGEMENT A20 NUMBERS FOR BEARINGS A38 12.2 Lubricating Methods A105 CONTENTS B2
4.1 Fixed-End and Free-End Bearings A20 7.1 Boundary Dimensions and Dimensions of 12.2.1 Grease Lubrication A105
4.2 Examples of Bearing Arrangements A21 Snap Ring Grooves A38 12.2.2 Oil Lubrication A107
7.1.1 Boundary Dimensions A38 12.3 Lubricants A110
5 SELECTION OF BEARING SIZE A24 7.1.2 Dimensions of Snap Ring Grooves 12.3.1 Lubricating Grease A110 INTRODUCTION OF NSK
5.1 Bearing Life A24 and Locating Snap Rings A38 12.3.2 Lubricating Oil A112 PRODUCTS-APPENDICES
5.1.1 Rolling Fatigue Life and Basic Rating 7.2 Formulation of Bearing Numbers A54
Life A24 13 BEARING MATERIALS A114 CONTENTS C 1
5.2 Basic Load Rating and Fatigue Life A24 8 BEARING TOLERANCES A58 13.1 Materials for Bearing Rings and Rolling Photos of NSK Products C 2
5.2.1 Basic Load Rating A24 8.1 Bearing Tolerance Standards A58 Elements A114 Appendix 1 Conversion from SI (International
5.2.2 Machinery in which Bearings are 8.2 Selection of Accuracy Classes A81 13.2 Cage Materials A115 Units) System C 8
Used and Projected Life A24 Appendix 2 N-kgf Conversion Table C10
5.2.3 Selection of Bearing Size Based on 9 FITS AND INTERNAL CLEARANCES A82 14 BEARING HANDLING A116 Appendix 3 kg-lb Conversion Table C11
Basic Load Rating A25 9.1 Fits A82 14.1 Precautions for Proper Handling of Appendix 4 C-F Temperature Conversion
5.2.4 Temperature Correction for Basic Load 9.1.1 Importance of Proper Fits A82 Bearings A116 Table C12
Rating A26 9.1.2 Selection of Fit A82 14.2 Mounting A116 Appendix 5 Viscosity Conversion Table C13
5.2.5 Correction of Basic Rating Life A27 9.1.3 Recommended Fits A83 14.2.1 Mounting of Bearings with Appendix 6 Inch-mm Conversion Table C14
5.3 Calculation of Bearing Loads A28 9.2 Bearing Internal Clearances A88 Cylindrical Bores A116 Appendix 7 Hardness Conversion Table C16
5.3.1 Load Factor A28 9.2.1 Internal Clearances and Their 14.2.2 Mounting of Bearings with Tapered Appendix 8 Physical and Mechanical Properties
5.3.2 Bearing Loads in Belt or Chain Standards A88 Bores A118 of Materials C17
Transmission Applications A28 9.2.2 Selection of Bearing Internal 14.3 Operation Inspection A118 Appendix 9 Tolerances for Shaft Diameters C18
5.3.3 Bearing Loads in Gear Transmission Clearances A94 14.4 Dismounting A121 Appendix 10 Tolerances for Housing Bore
Applications A29 14.4.1 Dismounting of Outer Rings A121 Diameters C20
5.3.4 Load Distribution on Bearings A29 10 PRELOAD A96 14.4.2 Dismounting of Bearings with Appendix 11 Values of Standard Tolerance Grades
5.3.5 Average of Fluctuating load A29 10.1 Purpose of Preload A96 Cylindrical Bores A121 IT C22
10.2 Preloading Methods A96 14.4.3 Dismounting of Bearings with Appendix 12 Speed Factor fn C24
10.2.1 Position Preload A96 Tapered Bores A122 Appendix 13 Fatigue Life Factor fh and Fatigue
10.2.2 Constant-Pressure Preload A96 14.5 Inspection of Bearings A123 Life L-Lh C25
14.5.1 Bearing Cleaning A123 Appendix 14 Index of Inch Design Tapered Roller
14.5.2 Inspection and Evaluation of Bearings C26
Bearings A123
A4 A5
A001-005E.indd 4-5 11/20/13 4:49:06 PM

1.TYPES AND FEATURES OF ROLLING BEARINGS
1.1 Design and Classification (2) With the advancement of worldwide standardization,
Rolling bearings generally consist of two rings, rolling rolling bearings are internationally available and
elements, and a cage, and they are classified into radial interchangeable.
bearings or thrust bearings depending on the direction (3) Maintenance, replacement, and inspection are easy
of the main load. In addition, depending on the type of because the structure surrounding rolling bearings
rolling elements, they are classified into ball bearings is simple.
or roller bearings, and they are further segregated by (4) Many rolling bearings are capable of taking
differences in their design or specific purpose. both radial and axial loads simultaneously or
The most common bearing types and nomenclature independently.
of bearing parts are shown in Fig.1.1, and a general (5) Rolling bearings can be used under a wide range of
classification of rolling bearings is shown in Fig. 1.2. temperatures.
(6) Rolling bearings can be preloaded to produce a
1.2 Characteristics of Rolling Bearings negative clearance and achieve greater rigidity.
Compared with plain bearings, rolling bearings have Furthermore, different types of rolling bearings have
the following major advantages: their own individual advantages. The features of the
(1) Their starting torque or friction is low and the most common rolling bearings are described on Pages
difference between the starting torque and running A10 to A12 and in Table 1.1 (Pages A14 and A15).
torque is small.
Width Contact Angle
Snap Ring
Outer Ring Outer Ring Outer Ring
Cage Front Face Outer Ring Rib
Back Face Inner Ring
Rivet Inner Ring Inner Ring Inner Ring Rib L-Shaped
Pitch Diameter
Ball Back Face Front Face
Outside Dia.
Thrust Collar
Bore Dia.
Circle Dia.
Inscribed
Roller
Effective
Inner Ring Load Center
Raceway Side Face
Outer Ring Shield
Raceway Cylindrical
Roller
Chamfer Dimension
Cross-Face Width
Single-Row Deep Groove Ball Bearing Single-Row Angular Contact Ball Bearing Cylindrical Roller Bearing
at
s Se
Bearing Width
diu ing
Ra lign
Stand out
A
Aligning Seat
Cone Front Face Rib Lock Center Height Bore Dia.
Tapered Roller
Adapter
Washer Shaft Washer
Cone Back Nut
Face Rib Contact Tapered Bore Sleeve Ball
Angle Height
Effective Load Housing Washer
Center Housing
Washer
Cone Back Bore Dia. Aligning
Face Cone Front Face Inner Ring Seat
Cup Front Spherical Roller Outside Dia. Washer
Cup Back Face Aligning Seat
Face Outer Ring
Washer O.D.
Tapered Roller Bearing Spherical Roller Bearing Single-Direction Thrust Ball Bearing
Fig. 1.1 Nomenclature for Bearing Parts
A6 A7
A007-023E.indd 6-7 11/20/13 4:49:25 PM

TYPES AND FEATURES OF ROLLING BEARINGS
ROLLING BEARINGS
(Radial Bearings) (Thrust Bearings)
Single
Row Single
Direction Single-Direction Thrust Ball Bearing
Deep Groove
Ball Bearings Thrust Ball
Double Bearings
Row Double
Deep Groove Ball Direction
Ball Bearing Magneto Bearings
Bearings Angular Contact
Thrust Ball Thrust Cylindrical Roller Bearing
Single Bearings
Row
Angular Thrust Cylindrical
Double Ball Roller Bearings
Contact Ball Bearings
Angular Contact Row Bearings Thrust Tapered Roller Bearing
Ball Bearing
Matched Thrust Needle
Roller Bearings
Roller
Three- Point/Four-Point Bearings
Contact Ball Bearings Thrust Tapered
Roller Bearings
Self-Aligning
Self-Aligning Ball Bearings
Ball Bearing Thrust Spherical Thrust Spherical Roller Bearing
Ball Bearings Roller Bearings
for Bearing
Units
Single Automotive Clutch

Row Cylindrical Release Bearings
Cylindrical
Roller Roller
Bearing Double Bearings
Automotive Water Sealed Axle Bearing
Row
Pump Bearings
Long-Roller
Bearings
Needle Rolling Stock
Roller Axle Bearings
Needle Roller Roller
Bearing Bearings Bearings
Bearings for Specific Uses Crane-Sheave
Single Bearings
Row Cylindrical Roller Bearing for Sheaves
Tapered Chain Conveyor
Double Roller
Row Bearings
Tapered Bearings
Roller
Bearing Four
Row Others
Spherical
Roller
Bearings
Spherical
Roller Fig. 1.2 Classification of Rolling Bearings
Bearing
A8 A9
A007-023E.indd 8-9 11/20/13 4:49:26 PM

Single-Row Single-row deep groove ball bearings are the most common type of rolling bearings. Their use Double-Row Double-row angular contact ball bearings are basically two single-row angular contact ball bearings
Deep Groove is very widespread. The raceway grooves on both the inner and outer rings have circular arcs of Angular Contact mounted back-to-back except that they have only one inner ring and one outer ring, each having
Ball Bearings slightly larger radius than that of the balls. In addition to radial loads, axial loads can be imposed Ball Bearings raceways. They can take axial loads in either direction.
in either direction. Because of their low torque, they are highly suitable for applications where high
speeds and low power loss are required.
In addition to open type bearings, these bearings often have steel shields or rubber seals installed
on one or both sides and are prelubricated with grease. Also, snap rings are sometimes used on
the periphery. As to cages, pressed steel ones are the most common.
Magneto The inner groove of magneto bearings is a little shallower than that of deep groove bearings. Four-Point The inner and outer rings of four-point contact ball bearings are separable because the inner ring
Bearings Since the outer ring has a shoulder on only one side, the outer ring may be removed. This is often Contact is split in a radial plane. They can take axial loads from either direction. The balls have a contact
advantageous for mounting. In general, two such bearings are used in duplex pairs. Magneto Ball Bearings angle of 35 with each ring. Just one bearing of this type can replace a combination of face-to-face
bearings are small bearings with a bore diameter of 4 to 20 mm and are mainly used for small or back-to-back angular contact bearings.
magnetos, gyroscopes, instruments, etc. Pressed brass cages are generally used. Machined brass cages are generally used.
Single-Row Individual bearings of this type are capable of taking radial loads and also axial loads in one Self-Aligning The inner ring of this type of bearing has two raceways and the outer ring has a single spherical
Angular Contact direction. Four contact angles of 15, 25, 30, and 40 are available. The larger the contact angle, Ball Bearings raceway with its center of curvature coincident with the bearing axis. Therefore, the axis of the
Ball Bearings the higher the axial load capacity. For high speed operation, however, the smaller contact angles inner ring, balls, and cage can deflect to some extent around the bearing center. Consequently,
are preferred. Usually, two bearings are used in duplex pairs, and the clearance between them minor angular misalignment of the shaft and housing caused by machining or mounting error is
must be adjusted properly. automatically corrected.
Pressed-steel cages are commonly used, however, for high precision bearings with a contact angle This type of bearing often has a tapered bore for mounting using an adapter sleeve.
less than 30, polyamide resin cages are often used.
Duplex Bearings A combination of two radial bearings is called a duplex pair. Usually, they are formed using angular Cylindrical In bearings of this type, the cylindrical rollers are in linear contact with the raceways. They have a
contact ball bearings or tapered roller bearings. Possible combinations include face-to-face, which Roller Bearings high radial load capacity and are suitable for high speeds.
have the outer ring faces together (type DF), back-to-back (type DB), or both front faces in the There are different types designated NU, NJ, NUP, N, NF for single-row bearings, and NNU, NN for
same direction (type DT). DF and DB duplex bearings are capable of taking radial loads and axial double-row bearings depending on the design or absence of side ribs.
loads in either direction. Type DT is used when there is a strong axial load in one direction and it is The outer and inner rings of all types are separable.
necessary to impose the load equally on each bearing. Some cylindrical roller bearings have no ribs on either the inner or outer ring, so the rings can
move axially relative to each other. These can be used as free-end bearings. Cylindrical roller
bearings, in which either the inner or outer rings has two ribs and the other ring has one, are
capable of taking some axial load in one direction. Double-row cylindrical roller bearings have high
radial rigidity and are used primarily for precision machine tools.
Pressed steel or machined brass cages are generally used, but sometimes molded polyamide
cages are also used.
A 10 A 11
A007-023E.indd 10-11 11/20/13 4:49:29 PM

Needle Needle roller bearings contain many slender rollers with a length 3 to 10 times their diameter. As a Single-Direction
Roller Bearings result, the ratio of the bearing outside diameter to the inscribed circle diameter is small, and they Thrust Ball
have a rather high radial load capacity. Bearings
There are numerous types available, and many have no inner rings. The drawn-cup type has a
pressed steel outer ring and the solid type has a machined outer ring. There are also cage and
roller assemblies without rings. Most bearings have pressed steel cages, but some are without
cages. Single-direction thrust ball bearings are composed of washer-like bearing rings with raceway
grooves. The ring attached to the shaft is called the shaft washer (or inner ring) while that attached
to the housing is called the housing washer(or outer ring).
In double-direction thrust ball bearings, there are three rings with the middle one (center ring)
Double-Direction being fixed to the shaft.
Thrust Ball There are also thrust ball bearings with an aligning seat washer beneath the housing washer in
Bearings order to compensate for shaft misalignment or mounting error.
Pressed steel cages are usually used in the smaller bearings and machined cages in the larger
Tapered Bearings of this type use conical rollers guided by a back-face rib on the cone. These bearings are ones.
Roller Bearings capable of taking high radial loads and also axial loads in one direction. In the HR series, the rollers
are increased in both size and number giving it an even higher load capacity.
They are generally mounted in pairs in a manner similar to single-row angular contact ball
bearings. In this case, the proper internal clearance can be obtained by adjusting the axial distance
between the cones or cups of the two opposed bearings. Since they are separable, the cone
assemblies and cups can be mounted independently.
Depending upon the contact angle, tapered roller bearings are divided into three types called the
normal angle, medium angle, and steep angle. Double-row and four-row tapered roller bearings are
also available. Pressed steel cages are generally used.
Spherical Thrust These bearings have a spherical raceway in the housing washer and barrel-shaped rollers obliquely
Roller Bearings arranged around it. Since the raceway in the housing washer in spherical, these bearings are self-
Spherical These bearings have barrel-shaped rollers between the inner ring, which has two raceways, and the aligning. They have a very high axial load capacity and are capable of taking moderate radial loads
Roller Bearings outer ring which has one spherical raceway. Since the center of curvature of the outer ring raceway when an axial load is applied.
surface coincides with the bearing axis, they are self-aligning in a manner similar to that of self- Pressed steel cages or machined brass cages are usually used.
aligning ball bearings. Therefore, if there is deflection of the shaft or housing or misalignment of
their axes, it is automatically corrected so excessive force is not applied to the bearings.
Spherical roller bearings can take, not only heavy radial loads, but also some axial loads in either
direction. They have excellent radial load-carrying capacity and are suitable for use where there are
heavy or impact loads.
Some bearings have tapered bores and may be mounted directly on tapered shafts or cylindrical
shafts using adapters or withdrawal sleeves.
Pressed steel and machined brass cages are used.
A 12 A 13
A007-023E.indd 12-13 11/20/13 4:49:32 PM

Table 1. 1 Types and Characteristics of Rolling Bearings
Deep Magneto Angular Double-Row Duplex Four-Point Self- Cylindrical Double-Row Cylindrical Cylindrical Needle Tapered Double-and Spherical Thrust Thrust Ball Double- Thrust Thrust Thrust
Groove Bearings Contact Angular Angular Contact Aligning Roller Cylindrical Roller Roller Roller Roller Multiple-Row Roller Ball Bearings Direction Cylindrical Tapered Spherical
Bearing Ball Ball Contact Contact Ball Ball Bearings Roller Bearings Bearings Bearings Bearings Tapered Bearings Bearings with Angular Roller Roller Roller
Types Bearings Bearings Ball Ball Bearings Bearings Bearings with with Thrust Roller Aligning Contact Bearings Bearings Bearings
Bearings Bearings Single Rib Collars Bearings Seat Thrust
Ball Page No.
Bearings
Features
Radial Loads
Load Capacity
Axial Loads
Combined
Loads
A18
High Speeds A37
A19
High Accuracy A58
A81
Low Noise and A19

Torque
A19
Rigidity A96
A18
Angular Blue pages of
Misalignment each brg.
type
Self-Aligning i i i i A18
Capability
Ring i i i i i i i i i i i i i i i A19
Separability A20
Fixed-End i i i i i i i i A20~
Bearing ~A21
Free-End I I I I I i i i I I
A20~
Bearing ~A27
A800
Tapered Bore i i i A118
in Inner Ring A122
roller thrust bearings

Two bearings are usually
usually mounted in opposition.
DT pairs is possible, but

30 , and 40 . Two bearings are
Clearance adjustment is
Contact angle of 35o
mounted in opposition.
Combination of DF and
Including NNU type
Including NUP type

usually mounted in
To be used with oil

use on free-end is not
use on free-end is
Including NF type
Contact angles of 15o, 25o
also available but

Two bearings are
KH, KV types are
Including needle
Including N type
Clearance adjustment is
impossible.
opposition.
Remarks
lubrication
necessary.
o
possible.
necessary.
o
B5 B5 B47 B47 B85 B115 B207 B207

Page No. B31 B28 B47 B70 B47 B72 B77 B85 B110 B85 B85 B115 B176 B183 B207 B207 B235 B224 B228
B299
Excellent Good Fair One direction

Poor Impossible
Two directions
only
i Applicable I Applicable, but it is necessary to allow shaft contraction/elongation at fitting surfaces of bearings.
A 14 A 15
A007-023E.indd 14-15 11/20/13 4:49:34 PM

2. BEARING SELECTION PROCEDURE Examination of fitting
Evaluation of accuracy Page number
Page number
The number of applications for rolling bearings is Then the size of the bearing is chosen to satisfy the A19
A Operating conditions A82
A Running accuracy
almost countless and the operating conditions and desired life requirement. When doing this, in addition A Rotational stability A18, A37, A81
A Magnitude and character- A82, A83
environments also vary greatly. In addition, the diversity to fatigue life, it is necessary to consider grease life, A Torque fluctuation A19 istics of loads
of operating conditions and bearing requirements noise and vibration, wear, and other factors.
A Temperature range A83
A Materials, size, accuracies A84, A100
continue to grow with the rapid advancement of There is no fixed procedure for selecting bearings. It is
Selection of bearing of shaft and housing
technology. Therefore, it is necessary to study bearings good to investigate experience with similar applications
carefully from many angles to select the best one from and studies relevant to any special requirements for accuracy class
the thousands of types and sizes available. your specific application. When selecting bearings for Page number Determination of fitting
Usually, a bearing type is provisionally chosen new machines, unusual operating conditions, or harsh Examination of A Fitting
considering the operating conditions, mounting environments, please consult with NSK. internal clearance A Difference in temperature A95
arrangement, ease of mounting in the machine, The following diagram (Fig.2.1) shows an example of between inner and outer
allowable space, cost, availability, and other factors. the bearing selection procedure. rings
A Speed
A Misalignment of inner and A18

outer rings
A Amount of preload A98
Determination of
internal clearance
A Operating conditions and required Examination of special
performance specifications
Study of cage Page number
A Environmental conditions A Speed A Operating temperature A57
A Dimensions of shaft and housing A Noise
A Operating temperature
A Environment (seawater,
A External vibration and shock
vacuum, gases, chemicals,
Page number A Rapid acceleration and
etc.)
Evaluation of A Allowable space A18, A38 A Type of lubrication
bearing types Magnitude and direction of loads deceleration
A A18 A Moment load and misalignment
A Vibration and shock A18
A Operating speed, maximum speed A18, A37 Selection of special
A Misalignment of inner and outer A18 material, heat treatment
Selection of cage type
rings for dimensional stability
A Fixing in axial direction and mounting
and material
A20 to A23
arrangement
A Ease of bearing mounting and A19 Page number
dismounting Examination of A Operating temperature range A106, A107, A110, A112
A Sound and torque A19 lubricating A Speed A37
A Required rigidity A19, A96 methods A Lubricating methods A105
A Availability and cost A Type of seals A102
A Maintenance and inspection A123
intervals
Determination of bearing
type and mounting Selection of lubricating
arrangement method, lubricant, and
type of seals
Page number Page number
Determination of A Expected life of machine A24, A25 Examination of A Procedure for mounting and A116, A121
bearing size A Dynamic and static equivalent loads A30, A32 ease of mounting/ dismounting
A Speed -- dismounting A Necessary equipment A116, A121
A Permissible static load factor A32 A Dimensions affecting A100
A Permissible axial loads (in the case of A33 mounting
cylindrical roller bearings)
Determination of dimensions
affecting mounting and
Determination of bearing size
procedure for mounting/
dismounting
Fig. 2.1 Flow Chart for Selection of Rolling Bearings Final specifications for
bearing and surrounding
parts
A 16 A 17
A007-023E.indd 16-17 11/20/13 4:49:36 PM

3. SELECTION OF BEARING TYPES
3.1 Allowable Bearing Space 3.3 Permissible Speed and Bearing Types Permissible bearing misalignment is given at the 3.5 Rigidity and Bearing Types
The allowable space for a rolling bearing and its The maximum speed of rolling bearings varies beginning of the dimensional tables for each bearing When loads are imposed on a rolling bearing, some
adjacent parts is generally limited so the type and size depending, not only the type of bearing, but also its type. elastic deformation occurs in the contact areas between
of the bearing must be selected within such limits. size, type of cage, loads, lubricating method, heat the rolling elements and raceways. The rigidity of the
In most cases, the shaft diameter is fixed first by the dissipation, etc. Assuming the common oil bath bearing is determined by the ratio of bearing load to
machine design; therefore, the bearing is often selected lubrication method, the bearing types are roughly the amount of elastic deformation of the inner and
based on its bore size. For rolling bearings, there are ranked from higher speed to lower as shown in Fig. outer rings and rolling elements. For the main spindles
numerous standardized dimension series and types, 3.3. of machine tools, it is necessary to have high rigidity
and the selection of the optimum bearing from among of the bearings together with the rest of the spindle.
them is necessary. Fig. 3.1 shows the dimension series 3.4 Misalignment of Inner/Outer Rings and Consequently, since roller bearings are deformed
of radial bearings and corresponding bearing types. Bearing Types less by load, they are more often selected than ball
Because of deflection of a shaft caused by applied bearings. When extra high rigidity is required, bearings
3.2 Load Capacity and Bearing Types loads, dimensional error of the shaft and housing,
are given a preload, which means that they have a
The axial load carrying capacity of a bearing is closely and mounting errors, the inner and outer rings are negative clearance. Angular contact ball bearings and
related to the radial load capacity (see Page A24) slightly misaligned. The permissible misalignment tapered roller bearings are often preloaded.
in a manner that depends on the bearing design as varies depending on the bearing type and operating
shown in Fig. 3.2. This figure makes it clear that when conditions, but usually it is a small angle less than 3.6 Noise and Torque of Various Bearing
bearings of the same dimension series are compared, 0.0012 radian (4'). Types
roller bearings have a higher load capacity than ball When a large misalignment is expected, bearings Since rolling bearings are manufactured with very
bearings and are superior if shock loads exist. having a self-aligning capability, such as self-aligning Fig. 3.4 Permissible Misalignment of Spherical Roller
high precision, noise and torque are minimal. For
ball bearings, spherical roller bearings, and certain Bearings deep groove ball bearings and cylindrical roller
bearing units should be selected (Figs. 3.4 and 3.5). bearings particularly, the noise level is sometimes
specified depending on their purpose. For high
Width Series 0 1 2 3 4 5 6 precision miniature ball bearings, the starting torque is
4 specified. Deep groove ball bearings are recommended
3 for applications in which low noise and torque are
Diameter Series 2
01 required, such as motors and instruments.
89
3.7 Running Accuracy and Bearing Types
Dimension
08
09
00
01
02
03
04
18
19
10
29
20
22
23
39
30
31
32
33
48
49
40
41
59
50
69
Series For the main spindles of machine tools that require
high running accuracy or high speed applications like
Deep Groove Ball Bearings I I I III superchargers, high precision bearings of Class 5, 4 or
Angular Contact Ball Bearings I I II II 2 are usually used.
Self-Aligning Ball Bearings I I II The running accuracy of rolling bearings is specified
Cylindrical Roller Bearings I I I II I II II I in various ways, and the specified accuracy classes
Spherical Roller Bearings I II I II I II Fig. 3.5 Permissible Misalignment of Ball Bearing Units
vary depending on the bearing type. A comparison
Needle Roller Bearings II I I of the inner ring radial runout for the highest running
Tapered Roller Bearings I I III I II I
accuracy specified for each bearing type is shown in
Fig. 3.6.
Fig. 3.1 Dimension Series of Radial Bearings For applications requiring high running accuracy, deep
Highest Tolerance comparison of groove ball bearings, angular contact ball bearings, and
Bearing Types accuracy inner ring radial runout
specified cylindrical roller bearings are most suitable.
Radial load capacity Axial load capacity Relative permissible speed 1 2 3 4 5
Bearing Type Bearing Types
1 2 3 4 1 2 3 4 1 4 7 10 13 Deep Groove Ball
Deep Groove Bearings
Class 2 3.8 Mounting and Dismounting of Various
Single-Row Deep
Groove Ball Bearings Ball Bearings
Angular Contact
Bearing Types
Class 2
Angular Contact Ball Bearings Separable types of bearings like cylindrical roller
Single-Row Angular Ball Bearings
Contact Ball Bearings Cylindrical Roller bearings, needle roller bearings and tapered roller
Cylindrical Roller Class 2
Bearings Bearings bearings are convenient for mounting and dismounting.
Cylindrical Roller(1) For machines in which bearings are mounted and
Bearings Needle Roller Tapered Roller Class 4
Bearings Bearings dismounted rather often for periodic inspection, these
Tapered Roller Tapered Roller
Spherical Roller
types of bearings are recommended. Also, self-aligning
Bearings Bearings Normal
Bearings ball bearings and spherical roller bearings (small ones)
Spherical Roller
Spherical Roller Bearings with tapered bores can be mounted and dismounted
Bearings Thrust Ball Bearings Fig. 3.6 Relative Inner Ring Radial Runout of Highest relatively easily using sleeves.
Accuracy Class for Various Bearing Types
Note(1) The bearings with ribs can take some axial loads. Remarks Oil bath lubrication
With special measures to increase speed limit
Fig. 3.2 Relative Load Capacities of Various Bearing Types Fig. 3.3 Relative Permissible Speeds of
Various Bearing Types
A 18 A 19
A007-023E.indd 18-19 11/20/13 4:49:37 PM

4. SELECTION OF BEARING ARRANGEMENT
In general, shafts are supported by only two bearings. If measures to relieve a shafts thermal elongation and The distinction between free-end and fixed-end 4.2 Example of Bearing Arrangements
When considering the bearing mounting arrangement, contraction are insufficient, abnormal axial loads are bearings and some possible bearing mounting Some representative bearing mounting arrangements
the following items must be investigated: applied to the bearings, which can cause premature arrangements for various bearing types are shown in considering preload and rigidity of the entire assembly,
(1) Expansion and contraction of the shaft caused by failure. Fig. 4.1. shaft elongation and contraction, mounting error, etc.
temperature variations. For free-end bearings, cylindrical roller bearings are shown in Table 4.1.
(2) Ease of bearing mounting and dismounting. or needle roller bearings with separable inner and
(3) Misalignment of the inner and outer rings caused outer rings that are free to move axially (NU, N types,
by deflection of the shaft or mounting error. etc.) are recommended. When these types are used, Table 4. 1 Representative Bearing Mounting Arrangements
(4) Rigidity of the entire system including bearings and mounting and dismounting are also easier. and Application Examples
preloading method. When non-separable types are used as free-end
(5) Capability to sustain the loads at their proper bearings, usually the fit between the outer ring and Bearing Arrangements
positions and to transmit them. housing is loose to allow axial movement of the Remarks Application Examples
running shaft together with the bearing. Sometimes, Fixed-end Free-end
4.1 Fixed-End and Free-End Bearings such elongation is relieved by a loose fitting between
Among the bearings on a shaft, only one can be a the inner ring and shaft.
"fixed-end" bearing that is used to fix the shaft axially. When the distance between the bearings is short and
the influence of the shaft elongation and contraction is fThis is a common arrangement in which Medium size electric motors,
For this fixed-end bearing, a type which can carry both abnormal loads are not applied to bearings blowers
radial and axial loads must be selected. negligible, two opposed angular contact ball bearings
even if the shaft expands or contracts.
Bearings other than the fixed-end one must be "free- or tapered roller bearings are used. The axial clearance
(possible axial movement) after the mounting is fIf the mounting error is small, this is suitable
end" bearings that carry only radial loads to relieve the for high speeds.
shaft's thermal elongation and contraction. adjusted using nuts or shims.
fThis can withstand heavy loads and shock loads Traction motors for rolling
and can take some axial load. stock
fEvery type of cylindrical roller bearing is
A B BEARING A
Deep Groove Ball Bearing
BEARING B
Cylindrical Roller Bearing
separable. This is helpful when interference is
necessary for both the inner and outer rings.
Matched Angular Contact (NU, N types)
Ball Bearing Needle Roller Bearing (NA
Fixed-end Free-end (separable bearing) Double-Row Angular type, etc.)
Contact Ball Bearing
Self-Aligning Ball Bearing
Cylindrical Roller Bearing fThis is used when loads are relatively heavy. Table rollers for steel mills,
A C with Ribs (NH, NUP BEARING C(1)
fFor maximum rigidity of the fixed-end bearing,
main spindles of lathes
types) Deep Groove Ball Bearing
it is a back-to-back type.
Double-Row Tapered Matched Angular Contact
Ball Bearing (back-to- fBoth the shaft and housing must have high
Fixed-end Free-end (non-separable bearing) Roller Bearing accuracy and the mounting error must be small.
Spherical Roller Bearing back)
Double-Row Angular
Contact Ball Bearing
D D Self-Aligning Ball Bearing
BEARING D,E(2) Double-Row Tapered
Angular Contact Ball Roller Bearing (KBE type)
Bearing Spherical Roller Bearing fThis is also suitable when interference is Calender rolls of paper making
No distinction between fixed-end and free-end
Tapered Roller Bearing necessary for both the inner and outer rings. machines, axles of diesel
Magneto Bearing Heavy axial loads cannot be applied. locomotives
Cylindrical Roller Bearing
E E (NJ, NF types) BEARING F
Deep Groove Ball Bearing
Self-Aligning Ball Bearing
Spherical Roller Bearing
No distinction between fixed-end and free-end fThis is suitable for high speeds and heavy radial Reduction gears in diesel
loads. Moderate axial loads can also be applied. locomotives
Notes: (1) In the figure, shaft elongation and contraction are fIt is necessary to provide some clearance
F F relieved at the outside surface of the outer ring, but between the outer ring of the deep groove ball
sometimes it is done at the bore. bearing and the housing bore in order to avoid
(2) For each type, two bearings are used in opposition. subjecting it to radial loads.
No distinction between fixed-end and free-end
Fig. 4.1 Bearing Mounting Arrangements and Bearing Types Continued on next page
A 20 A 21
A007-023E.indd 20-21 11/20/13 4:49:38 PM

SELECTION OF BEARING ARRANGEMENT
Table 4. 1 Representative Bearing Mounting Arrangements

and Application Examples (cont'd)
Bearing Arrangements
When there is no distinction between
Remarks Application Examples Remarks Application Examples
fixed-end and free-end
Fixed-end Free-end
fThis can withstand heavy loads and shock Final reduction gears of
loads. construction machines
fThis is the most common arrangement. Double suction volute pumps, fIt can be used if interference is necessary for
automotive transmissions both the inner and outer rings.
fIt can sustain not only radial loads, but
moderate axial loads also. fCare must be taken so the axial clearance
doesn't become too small during running.
NJ + NJ mounting fNF type + NF type mounting is also possible.
fSometimes a spring is used at the side of the Small electric motors, small
fThis is the most suitable arrangement when Speed reducers, table rollers of outer ring of one bearing. speed reducers, small pumps
there is mounting error or shaft deflection. steel mills, wheels for overhead
fIt is often used for general and industrial travelling cranes
applications in which heavy loads are applied.
Vertical arrangements Remarks Application Examples

fThis is suitable when there are rather heavy Worm gear reducers
axial loads in both directions.
fDouble row angular contact bearings may be
used instead of a arrangement of two angular fMatched angular contact ball bearings are on Vertical electric motors
contact ball bearings. the fixed end.
fCylindrical roller bearing is on the free end.
When there is no distinction between
Remarks Application Examples
fixed-end and free-end
fThis arrangement is widely used since it can Pinion shafts of automotive

withstand heavy loads and shock loads. differential gears, automotive
fThe back-to-back arrangement is especially front and rear axles, worm gear
good when the distance between bearings is reducers
short and moment loads are applied.
Back-to-back mounting
fFace-to-face mounting makes mounting easier
when interference is necessary for the inner
ring. In general, this arrangement is good when
there is mounting error.
fThe spherical center of the self-aligning seat Vertical openers (spinning and
fTo use this arrangement with a preload, must coincide with that of the self-aligning ball weaving machines)
affection must be paid to the amount of preload bearing.
and clearance adjustment.
Face-to-face mounting fThe upper bearing is on the free end.
fThis is used at high speeds when radial loads Grinding wheel shafts
are not so heavy and axial loads are relatively
heavy.
fIt provides good rigidity of the shaft by
preloading.
Back-to-back mounting
fFor moment loads, back-to-back mounting is
better than face-to-face mounting.
Continued on next page
A 22 A 23
A007-023E.indd 22-23 11/20/13 4:49:39 PM

5. SELECTION OF BEARING SIZE
5.1 Bearing Life of grease-prelubricated bearings (refer to Section 12, Table 5. 1 Fatigue Life Factor f h for Various Bearing Applications
The various functions required of rolling bearings vary Lubrication, Page A107) can be estimated. Since noise
life and abrasion life are judged according to individual Fatigue Life Factor f h
according to the bearing application. These functions Operating Periods
must be performed for a prolonged period. Even if standards for different applications, specific values for ~3 2~4 3~5 4~7 6~
bearings are properly mounted and correctly operated, noise or abrasion life must be determined empirically. Small motors for Agricultural
they will eventually fail to perform satisfactorily due home appliances equipment
5.2 Basic Load Rating and Fatigue Life Infrequently used or only like vacuum
to an increase in noise and vibration, loss of running for short periods cleaners and
accuracy, deterioration of grease, or fatigue flaking of 5.2.1 Basic Load Rating washing machines
Hand power tools
the rolling surfaces. The basic load rating is defined as the constant load
Bearing life, in the broad sense of the term, is the
Motors for home Conveyors
applied on bearings with stationary outer rings that the Used only occasionally heaters and air Elevator cable
period during which bearings continue to operate and inner rings can endure for a rating life of one million but reliability is impor- conditioners sheaves
to satisfy their required functions. This bearing life revolutions (106 rev). The basic load rating of radial tant Construction
may be defined as noise life, abrasion life, grease life, equipment

bearings is defined as a central radial load of constant Rolling mill roll Small motors Factory motors Crane sheaves
or rolling fatigue life, depending on which one causes direction and magnitude, while the basic load rating of necks Deck cranes Machine tools Compressors
loss of bearing service. thrust bearings is defined as an axial load of constant Used intermittently for General cargo Transmissions Specialized
relatively long periods cranes Vibrating screens transmissions
Aside from the failure of bearings to function due magnitude in the same direction as the central axis. Pinion stands Crushers
to natural deterioration, bearings may fail when The load ratings are listed under C r for radial bearings Passenger cars
conditions such as heat-seizure, fracture, scoring of and C a for thrust bearings in the dimension tables. Escalators Centrifugal Mine hoists Paper making
the rings, damage of the seals or the cage, or other separators Press flywheels machines
Air conditioning Railway traction
damage occurs. 5.2.2 Machinery in which Bearings are Used and equipment motors
Conditions such as these should not be interpreted Projected Life Used intermittently for Blowers Locomotive axle
more than eight hours Woodworking boxes
as normal bearing failure since they often occur as a It is not advisable to select bearings with unnecessarily daily machines
result of errors in bearing selection, improper design high load ratings, for such bearings may be too large Large motors
or manufacture of the bearing surroundings, incorrect and uneconomical. In addition, the bearing life alone Axle boxes on
mounting, or insufficient maintenance. railway rolling stock

should not be the deciding factor in the selection of Waterworks pumps
bearings. The strength, rigidity, and design of the shaft Used continuously and Electric power
5.1.1 Rolling Fatigue Life and Basic Rating Life high reliability is impor- stations
tant Mine draining
When rolling bearings are operated under load, the pumps
raceways of their inner and outer rings and rolling
elements are subjected to repeated cyclic stress.
Because of metal fatigue of the rolling contact surfaces on which the bearings are to be mounted should also By designating the basic rating life as L h (h), bearing
of the raceways and rolling elements, scaly particles be considered. Bearings are used in a wide range of speed as n (min1), fatigue life factor as f h, and speed
may separate from the bearing material (Fig. 5.1). applications and the design life varies with specific factor as f n, the relations shown in Table 5.2 are
This phenomenon is called "flaking". Rolling fatigue applications and operating conditions. Table 5.1 gives obtained:
life is represented by the total number of revolutions an empirical fatigue life factor derived from customary
at which time the bearing surface will start flaking due operating experience for various machines. Also refer
to stress. This is called fatigue life. As shown in Fig. to Table 5.2.
5.2, even for seemingly identical bearings, which are Table 5. 2 Basic Rating Life, Fatigue Life
5.2.3 Selection of Bearing Size Based on Basic Load Factor and Speed Factor
of the same type, size, and material and receive the
same heat treatment and other processing, the rolling Rating Life
Parameters Ball Bearings Roller Bearings
fatigue life varies greatly even under identical operating The following relation exists between bearing load and
conditions. This is because the flaking of materials basic rating life: Basic
3
Fig. 5.1 Example of Flaking
( )
3 10 10
due to fatigue is subject to many other variables. For ball bearings L = C . . . . . . . . . . . . . . . . (5.1) 106 C =
() ( ) =500 f
6
Rating L h= 500 fh3 L h= 10 C 3
h
3
Consequently, "basic rating life", in which rolling fatigue P Life 60n P 60n P
10
life is treated as a statistical phenomenon, is used in C
preference to actual rolling fatigue life. ( )
For roller bearings L = P 3 . . . . . . . . . . . . . . (5.2) Fatigue C
Suppose a number of bearings of the same type are where L : Basic rating life (106 rev) Life f h = fn C fh = fn P
Rating Life
P
operated individually under the same conditions. After P : Bearing load (equivalent load) (N), {kgf} Factor
Failure Probability
a certain period of time, 10 % of them fail as a result of ..........(Refer to Page A30)

C : Basic load rating (N), {kgf}
Average Life
flaking caused by rolling fatigue. The total number of 1 3
( ) ( )
6 6
revolutions at this point is defined as the basic rating For radial bearings, C is written C r Speed fn = 50010
60n
3 fn = 50010
60n
10
life or, if the speed is constant, the basic rating life For thrust bearings, C is written C a Factor 1 3
is often expressed by the total number of operating = (0.03n)- 3 = (0.03n)- 10

hours completed when 10 % of the bearings become In the case of bearings that run at a constant speed,
inoperable due to flaking. it is convenient to express the fatigue life in terms of
hours. In general, the fatigue life of bearings used in n, f n......Fig. 5.3 (See Page A26), Appendix Table 12
In determining bearing life, basic rating life is often the Life automobiles and other vehicles is given in terms of (See Page C24)
only factor considered. However, other factors must mileage. L h, f h....Fig. 5.4 (See Page A26), Appendix Table 13
Fig. 5.2 Failure Probability and Bearing Life (See Page C25)
also be taken into account. For example, the grease life
A 24 A 25
A024-057E.indd 24-25 11/20/13 4:50:10 PM

SELECTION OF BEARING SIZE
n fn n fn Lh fh Lh fh If the bearing load P and speed n are 5.2.5 Correction of Basic Rating Life The life adjustment factor for operating conditions
(min1) (min1) (h) (h) known, determine a fatigue life factor f h As described previously, the basic equations for a 3 is used to adjust for various factors, particularly
60000 0.08 60000 0.105 appropriate for the projected life of the calculating the basic rating life are as follows: lubrication. If there is no misalignment between
5.5 80000
0.11 80000 4.5 machine and then calculate the basic the inner and outer rings and the thickness of the
C 3
40000
30000
0.09
0.1
40000
30000
0.12
0.13
60000 5.0 60000
4.0
load rating C by means of the following
equation.
( )
For ball bearings L 10 = P . . . . . . . . . . . . . . . . . (5.5) lubricating film in the contact zones of the bearing is
sufficient, it is possible for a 3 to be greater than one;
10
however, a 3 is less than one in the following cases:
20000 0.12
20000
0.14
0.15
40000
4.5
40000
C=
fh P
. . . . . . . . . . . . . . . . . . . . . . . (5.3)
C
( )
For roller bearings L 10 = P 3 . . . . . . . . . . . . . . . (5.6)
When the viscosity of the lubricant in the
15000 15000 0.16
30000
4.0
30000
3.5 fn The L 10 life is defined as the basic rating life with contact zones between the raceways and rolling
0.14 0.17
10000 0.18 A bearing which satisfies this value of a statistical reliability of 90%. Depending on the elements is low.
10000
8000 0.16 8000 0.19
20000
3.5 20000 3.0 C should then be selected from the bearing machines in which the bearings are used, sometimes a When the circumferential speed of the rolling
0.20
6000 6000 tables. reliability higher than 90% may be required. However, elements is very slow.
0.18 15000
15000
3.0
recent improvements in bearing material have greatly When the bearing temperature is high.
4000 0.20 4000
5.2.4 Temperature Adjustment for Basic extended the fatigue life. In addition, the developent of
0.25 2.5 When the lubricant is contaminated by water or
3000 3000 10000 10000
Load Rating the Elasto-Hydrodynamic Theory of Lubrication proves
that the thickness of the lubricating film in the contact foreign matter.
8000
2000
0.25 2000
0.30
8000 2.5 If rolling bearings are used at high zone between rings and rolling elements greatly When misalignment of the inner and outer rings
temperature, the hardness of the bearing influences bearing life. To reflect such improvements
1500 1500
6000 6000 is excessive.
0.3 2.0
steel decreases. Consequently, the basic in the calculation of fatigue life, the basic rating life is
0.35
1000 1000 load rating, which depends on the physical adjusted using the following adjustment factors:
1.9 It is difficult to determine the proper value for a 3 for
800 800 4000 2.0 4000 properties of the material, also decreases.
0.40 1.8 specific operating conditions because there are still
600 600
1.9 Therefore, the basic load rating should be L na = a 1 a 2 a 3 L 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.7)
0.4 3000 1.8
3000 1.7 many unknowns. Since the special bearing property
0.45 adjusted for the higher temperature using
1.7 1.6 where L na : Adjusted rating life in which reliability, factor a 2 is also influenced by the operating conditions,
400 400 the following equation:
0.5 1.6 2000 material improvements, lubricating there is a proposal to combine a 2 and a 3 into one
C t = f t C . . . . . . . . . . . . . . . . . . . . . . . (5.4)
300 300 2000 1.5
0.5
1.5 conditions, etc. are considered quantity(a 2 a 3), and not consider them independently.
1.4
200 200 1500 1500
where C t : Basic load rating after In this case, under normal lubricating and operating
0.6 1.4 L 10 : Basic rating life with a reliability of 90% conditions, the product (a 2 a 3) should be assumed
150 0.6 150 1.3 temperature correction
1000
1.3
1000 (N), {kgf} a 1 : Life adjustment factor for reliability equal to one. However, if the viscosity of the lubricant
0.7 1.2
100 0.7 100
a 2 : Life adjustment factor for special bearing is too low, the value drops to as low as 0.2.
80 80 800
1.2 800 f t : Temperature factor If there is no misalignment and a lubricant with high
0.8
1.1
1.1 (See Table 5.3.) properties
0.8
60 60 600 viscosity is used so sufficient fluid-film thickness is
50
0.9
50 0.9
600
500 1.0 C : Basic load rating before a 3 : Life adjustment factor for operating secured, the product of (a 2 a 3) may be about two.
500 1.0
40 40
temperature adjustment conditions
1.0 0.95 0.95
(N), {kgf}
1.0 400
30 30 400
0.90 0.90 The life adjustment factor for reliability, a 1, is listed in When selecting a bearing based on the basic load
1.1 1.1
300 0.85 300 0.85 If large bearings are used at higher Table 5.4 for reliabilities higher than 90%. rating, it is best to choose an a 1 reliability factor
20 20
1.2 1.2
0.80 0.80 than 120 oC, they must be given special The life adjustment factor for special bearing appropriate for the projected use and an empirically
15 1.3 15
1.3
0.75 dimensional stability heat treatment to properties, a 2, is used to reflect improvements in determined C/P or f h value derived from past results
1.4 200 200
10 1.5 10
1.4
0.75
prevent excessive dimensional changes. bearing steel. for lubrication, temperature, mounting conditions, etc.
The basic load rating of bearings given such NSK now uses vacuum degassed bearing steel, and in similar machines.
special dimensional stability heat treatment the results of tests by NSK show that life is greatly
Ball Roller Ball Roller improved when compared with earlier materials. The
may become lower than the basic load The basic rating life equations (5.1), (5.2), (5.5), and
Bearings Bearings Bearings Bearings basic load ratings C r and C a listed in the bearing tables
rating listed in the bearing tables. (5.6) give satisfactory results for a broad range of
were calculated considering the extended life achieved bearing loads. However, extra heavy loads may cause
Fig. 5.3 Bearing Speed and Fig. 5.4 Fatigue Life Factor by improvements in materials and manufacturing detrimental plastic deformation at ball/raceway contact
Speed Factor and Fatigue Life techniques. Consequently, when estimating life using points. When Pr exceeds C 0 r (Basic static load rating)
Equation (5.7), it is sufficient to assume that is greater or 0.5 C r, whichever is smaller, for radial bearings or
than one. Pa exceeds 0.5 C a for thrust bearings, please consult
NSK to establish the applicablity of the rating fatigue
life equations.
Table 5.3 Temperature Factor f t Table 5.4 Reliability Factor a 1

Bearing
125 150 175 200 250 Reliability (%) 90 95 96 97 98 99
Temperature oC
Temperature
Factor f t
1.00 1.00 0.95 0.90 0.75 a1 1.00 0.62 0.53 0.44 0.33 0.21
A 26 A 27
A024-057E.indd 26-27 11/20/13 4:50:12 PM

5.3 Calculation of Bearing Loads 5.3.2 Bearing Loads in Belt or Chain Transmission 5.3.3 Bearing Loads in Gear Transmission 5.3.4 Load Distribution on Bearings
The loads applied on bearings generally include the Applications Applications In the simple examples shown in Figs. 5.5 and 5.6.
weight of the body to be supported by the bearings, The force acting on the pulley or sprocket wheel when The loads imposed on gears in gear transmissions vary The radial loads on bearings1 and 2 can be calculated
the weight of the revolving elements themselves, the power is transmitted by a belt or chain is calculated according to the type of gears used. In the simplest using the following equations:
transmission power of gears and belting, the load using the following equations. case of spur gears, the load is calculated as follows: b
produced by the operation of the machine in which the FC1 = c K ...............................................(5.16)
M = 9 550 000H / n ....( N m m ) M = 9 550 000H / n ....( N m m )
bearings are used, etc. These loads can be theoretically
calculated, but some of them are difficult to estimate. = 0 974 000H / n ....{kgf mm}
}
.............(5.9)
= 0 974 000H / n ....{kgf mm}
}
...........(5.12) a
FC2 = c K ..............................................(5.17)
Therefore, it becomes necessary to correct the
estimated using empirically derived data. Pk = M / r .............................................(5.10) Pk = M / r .............................................(5.13) where FC1 : Radial load applied on bearing1
Sk = Pk tan ...........................................(5.14) (N), {kgf}
5.3.1 Load Factor where M : Torque acting on pulley or sprocket
wheel (N mm), {kgf mm} Kc = P k2+ S k2 = Pk sec .........................(5.15) FC2 : Radial load applied on bearing 2
When a radial or axial load has been mathematically where M : Torque applied to gear (N), {kgf}
calculated, the actual load on the bearing may be Pk : Effective force transmitted by belt or
chain (N), {kgf} (N . mm),{kgf . mm} K : Shaft load (N), {kgf}
greater than the calculated load because of vibration
and shock present during operation of the machine. H : Power transmitted(kW) Pk : Tangential force on gear (N), {kgf}
The actual load may be calculated using the following When these loads are applied simultaneously, first the
n : Speed (min1) Sk : Radial force on gear (N), {kgf} radial load for each should be obtained, and then, the
equation:
Kc : Combined force imposed on gear sum of the vectors may be calculated according to the
r : Effective radius of pulley or sprocket load direction.
Fr = fw Frc
Fa = fw Fac
} . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.8) wheel (mm) (N), {kgf}
H : Power transmitted (kW)
When calculating the load on a pulley shaft, the belt
where Fr, Fa : Loads applied on bearing (N), {kgf} n : Speed (min1)
tension must be included. Thus, to calculate the actual c a
Frc, Fac : Theoretically calculated load (N), load Kb in the case of a belt transmission, the effective r : Pitch circle radius of drive gear (mm) a b c b
{kgf} transmitting power is multiplied by the belt factor f b,
which represents the belt tension. The values of the : Pressure angle
fw : Load factor belt factor f b for different types of belts are shown in FC1
The values given in Table 5.5 are usually used for the Table 5.6. In addition to the theoretical load calculated above, FC1 FC2
load factor fw. Kb = f b Pk .........................................(5.11) vibration and shock (which depend on how accurately
the gear is finished) should be included using the gear K
In the case of a chain transmission, the values factor f g by multiplying the theoretically calculated load Bearing1 K Bearing 2 Bearing1 FC2 Bearing 2
corresponding to f b should be 1.25 to 1.5. by this factor.
The values of f g should generally be those in Table 5.7. Fig. 5.5 Radial Load Fig. 5.6 Radial Load
When vibration from other sources accompanies gear Distribution (1) Distribution (2)
operation, the actual load is obtained by multiplying
the load factor by this gear factor.
5.3.5 Average of Fluctuating Load
Table 5. 5 Values of Load Factor fw Table 5. 6 Belt Factor f b When the load applied on bearings fluctuates, an
average load which will yield the same bearing life as
Operating Conditions Typical Applications fw Type of Belt fb Table 5. 7 Values of Gear Factor f g the fluctuating load should be calculated.
Smooth operation Electric motors, 1.0 to 1.2 Gear Finish Accuracy fg (1) When the relation between load and rotating speed
free from shocks Machine tools, Toothed belts 1.3 to 2.0 is divided into the following steps (Fig. 5.7)
Air conditioners
V belts 2.0 to 2.5 Precision ground gears 1.0~1.1 Load F1 : Speed n1 ; Operating time t1
Normal operation Air blowers, 1.2 to 1.5 Flat belts with tension pulley 2.5 to 3.0
Load F2 : Speed n2 ; Operating time t2

Compressors,
Elevators, Cranes, Flat belts 4.0 to 5.0 Ordinary machined gears 1.1~1.3 Load Fn : Speed nn ; Operating time tn
Paper making
machines Then, the average load Fm may be calculated using the
Operation Construction 1.5 to 3.0 following equation:
accompanied by equipment, Crushers,

F nn tt ++ Fn tn+t.........
p
shock and vibration Vibrating screens,
Fm = 1
p
1 1 + ... + F n t
2
p
2 2 n
p
n n
Rolling mills
1 1 2 2 +n t n n
..........................(5.18)
where Fm : Average fluctuating load (N), {kgf}

p = 3 for ball bearings
p = 10/3 for roller bearings
A 28 A 29
A024-057E.indd 28-29 11/20/13 4:50:13 PM

The average speed nm may be calculated as follows: 5.4 Equivalent Load 5.4.1 Calculation of Equivalent Loads center for each bearing is listed in the bearing tables.
n t +n t2 + ...+ nntn ........................(5.19) In some cases, the loads applied on bearings are The equivalent load on radial bearings may be When radial loads are applied to these types of
nm = 1 1 2 ......... bearings, a component of load is produced in the axial
t1 + t2 + + tn purely radial or axial loads; however, in most cases, calculated using the following equation:
direction. In order to balance this component load,
(2) When the load fluctuates almost linearly (Fig. 5.8), the loads are a combination of both. In addition, such P = XFr + YFa ........................................(5.25) bearings of the same type are used in pairs, placed
the average load may be calculated as follows: loads usually fluctuate in both magnitude and direction.
In such cases, the loads actually applied on bearings where P : Equivalent Load (N), {kgf} face to face or back to back. These axial loads can be
1 calculated using the following equation:
FmH (Fmin + 2Fmax) .........................(5.20) cannot be used for bearing life calculations; therefore, Fr : Radial load (N), {kgf}
3 a hypothetical load that has a constant magnitude and
passes through the center of the bearing, and will give
Fa : Axial load (N), {kgf} Fa i = 0.6 Fr ...................................(5.27)
where Fmin : Minimum value of fluctuating load Y
the same bearing life that the bearing would attain X : Radial load factor
(N), {kgf} where Fa i : Component load in the axial direction
under actual conditions of load and rotation should Y : Axial load factor
Fmax : Maximum value of fluctuating load be estimated. Such a hypothetical load is called the (N), {kgf}
(N), {kgf} The values of X and Y are listed in the bearing tables.
equivalent load. Fr : Radial load (N), {kgf}
The equivalent radial load for radial roller bearings with
(3) When the load fluctuation is similar to a sine wave = 0 is Y : Axial load factor
(Fig. 5.9), an approximate value for the average P = Fr
load F m may be calculated from the following Assume that radial loads F r1 and F r2 are applied
equation: In general, thrust ball bearings cannot take radial on bearings1and 2 (Fig. 5.12) respectively, and an
Fmax loads, but spherical thrust roller bearings can take external axial load Fae is applied as shown. If the axial
In the case of Fig. 5.9 (a) some radial loads. In this case, the equivalent load may load factors are Y1, Y2 and the radial load factor is X,
FmH0.65 Fmax ........................................(5.21) Fm be calculated using the following equation: then the equivalent loads P1 , P2 may be calculated as
In the case of Fig. 5.9 (b) P = Fa + 1.2Fr ..................................(5.26) follows:
F
FmH0.75 Fmax ........................................(5.22) Fr
0.6 0.6
where Fa 0.55 where Fae + F F
(4) When both a rotating load and a stationary load are Y2 r2 Y1 r1
applied (Fig. 5.10). 0 0.6
niti 5.4.2 Axial Load Components in Angular Contact P1 = XFr1 + Y1 Fae +
( F )
FR : Rotating load (N), {kgf} (a) Ball Bearings and Tapered Roller Bearings
P2 = Fr2
Y2 r2 } ..............(5.28)
FS : Stationary load (N), {kgf} The effective load center of both angular contact
An approximate value for the average load Fm may ball bearings and tapered roller bearings is at the 0.6 0.6
point of intersection of the shaft center line and a line where Fae + F < F
be calculated as follows: Y2 r2 Y1 r1
F max representing the load applied on the rolling element by
a) Where FRFS Fm the outer ring as shown in Fig. 5.11. This effective load P1 = Fr1
FS2
)}
...............(5.29)
FmHFR + 0.3FS + 0.2 F ..........................(5.23)
R
P2 = XFr2 + Y2 ( 0.6
Y 1
Fr1 Fae
b) Where FR<FS F
FR2
FmHFS + 0.3FR + 0.2 ..........................(5.24)
FS
0
niti
(b)
Fig. 5.9 Sinusoidal Load Variation Bearing I Bearing 2 Bearing I Bearing 2

F1
Fmax Fae
Fs Fr I Fr2 F ae F r2
F2 Fm Fm Fr I
F (a) (b)
F a a
Fig. 5.11 Effective Load Centers Fig. 5.12 Loads in Opposed Duplex Arrangement
Fn Fmin FR
0 n1 t1 n2 t2 nn tn 0
niti
Fig. 5.7 Incremental Load Variation Fig. 5.8 Simple Load Fluctuation Fig. 5.10 Rotating Load and
Stationary Load
A 30 A 31
A024-057E.indd 30-31 11/20/13 4:50:15 PM

5.5 Static Load Ratings and Static Equivalent where Po : Static equivalent load (N), {kgf} 5.6 Maximum Permissible Axial Loads for f : Load Factor k : Size Factor
Loads Fr : Radial load (N), {kgf} Cylindrical Roller Bearings
5.5.1 Static Load Ratings Fa : Axial load (N), {kgf} Cylindrical roller bearings having inner and outer Loading Interval Value of f Diameter series Value of k
Xo : Static radial load factor rings with ribs, loose ribs or thrust collars are capable
When subjected to an excessive load or a strong shock Yo : Static axial load factor Continuous 1 2 0.75
load, rolling bearings may incur a local permanent of sustaining radial loads and limited axial loads
(b)Static equivalent load on thrust bearings simultaneously. The maximum permissible axial load is Intermittent 2 3 1
deformation of the rolling elements and permanent
deformation of the rolling elements and raceway Po = Xo Fr + Fa =/ 90 .......................(5.32) limited by an abnormal temperature rise or heat seizure Short time only 3 4 1.2
surface if the elastic limit is exceeded. The nonelastic due to sliding friction between the end faces of rollers
deformation increases in area and depth as the load where Po : Static equivalent load (N), {kgf} and the rib face, or the rib strength. In the equations (5.34) and (5.35), the examination
increases, and when the load exceeds a certain limit, : Contact angle The maximum permissible axial load (the load for the rib strength is excluded. Concerning the rib
the smooth running of the bearing is impeded. considered the heat generation between the end face of strength, please consult with NSK.
When Fa<Xo Fr , this equation becomes less accurate. rollers and the rib face) for bearings of diameter series
The basic static load rating is defined as that static In addition, for cylindrical roller bearings to have
The values of Xo and Yo for Equations (5.30) and 3 that are continuously loaded and lubricated with
load which produces the following calculated contact a stable axial-load carrying capacity, the following
(5.32) are listed in the bearing tables. grease or oil is shown in Fig. 5.13.
stress at the center of the contact area between the precautions are required for the bearings and their
The static equivalent load for thrust roller bearings with
rolling element subjected to the maximum stress and surroundings:
the raceway surface. = 90 is Po = Fa Grease lubrication (Empirical equation) Radial load must be applied and the magnitude
900 (kd)2 of radial load should be larger than that of axial

For self-aligning ball bearings 4 600MPa CA = 9.8f n + 1 500 0.023 (kd)2.5 ...(N)
{ }
}
5.5.3 Permissible Static Load Factor load by 2.5 times or more.
{469kgf/mm2} .......(5.34)
The permissible static equivalent load on bearings 900 (kd)2 Sufficient lubricant must exist between the roller
For other ball bearings 4 200MPa varies depending on the basic static load rating and = f n + 1 500 0.023 (kd)2.5 .....{kgf}
{ } end faces and ribs.
{428kgf/mm2} also their application and operating conditions.
For roller bearings 4 000MPa The permissible static load factor fs is a safety factor Superior extreme-pressure grease must be used.
Oil lubrication (Empirical equation)
{408kgf/mm2} that is applied to the basic static load rating, and it is 490 (kd)2 Sufficient running-in should be done.
CA = 9.8f n + 1 000 0.000135 (kd)3.4 ...(N)
{ }
}
In this most heavily stressed contact area, the sum of defined by the ratio in Equation (5.33). The generally
recommended values of f s are listed in Table 5.8. ...(5.35) The mounting accuracy must be good.
the permanent deformation of the rolling element and 490 (kd)2
that of the raceway is nearly 0.0001 times the rolling Conforming to the modification of the static load rating, = f n + 1 000 0.000135 (kd)3.4 .....{kgf}
{ } The radial clearance should not be more than

element's diameter. The basic static load rating Co the values of fs were revised, especially for bearings for necessary.
is written Cor for radial bearings and Coa for thrust which the values of Co were increased, please keep this
in mind when selecting bearings. where CA : Permissible axial load (N), {kgf} In cases where the bearing speed is extremely slow, the
bearings in the bearing tables. speed exceeds the limiting speed by more than 50%, or
In addition, following the modification of the criteria Co
d : Bearing bore diameter (mm) the bore diameter is more than 200mm, careful study is
for basic static load rating by ISO, the new Co values fs = ...............................................(5.33) n : Speed (min1) necessary for each case regarding lubrication, cooling,
for NSK's ball bearings became about 0.8 to 1.3 times Po
etc. In such a case, please consult with NSK.
the past values and those for roller bearings about 1.5
to 1.9 times. Consequently, the values of permissible where Co : Basic static load rating (N), {kgf} kgf kgf
N N
static load factor fs have also changed, so please pay
attention to this. Po : Static equivalent load (N), {kgf} 5,000 50,000 5,000 50,000
4,000 40,000 d=1 4,000 40,000 d=1
For spherical thrust roller bearings, the values of fs 2
5.5.2 Static Equivalent Loads should be greater than 4.
3,000 30,000 2
100 0 3,000 30,000 100 0
The static equivalent load is a hypothetical load 2,000 20,000 80 2,000 20,000 80
that produces a contact stress equal to the above
maximum stress under actual conditions, while the 60 60
1,000 10,000 1,000 10,000
bearing is stationary (including very slow rotation or 800 8,000 50 800 8,000 50
oscillation), in the area of contact between the most CA 600 6,000 40 CA 600 6,000
heavily stressed rolling element and bearing raceway. 5,000 5,000 40
500 500
The static radial load passing through the bearing 400 4,000 400 4,000
center is taken as the static equivalent load for radial Table 5. 8 Values of Permissible Static Load Factor fs 300 3,000 300 3,000
bearings, while the static axial load in the direction
200 2,000 200 2,000
coinciding with the central axis is taken as the static Lower Limit of fs
equivalent load for thrust bearings. Operating Conditions
Ball Bearings Roller Bearings
(a) Static equivalent load on radial bearings 100 1,000 100 1,000
Low-noise applications 2.0 3.0 80 800 80 800
The greater of the two values calculated from the 600 600
Bearings subjected to vibration and 60 60
following equations should be adopted as the static 1.5 2.0 50 500 50 500
equivalent load on radial bearings. shock loads 200 300 400 600 1,000 2,000 4,000 6,000 10,000 200 300 400 600 1,000 2,000 4,000 6,000 10,000
Grease Lubrication n min1 Oil Lubrication n min1
Po = Xo Fr + Yo Fa ...................................(5.30) Standard operating conditions 1.0 1.5
Po = Fr ..................................................(5.31) Fig. 5.13 Permissible Axial Load for Cylindrical Roller Bearings
For Diameter Series 3 bearings (k=1.0) operating under a continuous load and lubricated with grease or oil.
A 32 A 33
A024-057E.indd 32-33 11/20/13 4:50:16 PM

5.7 Examples of Bearing Calculations (Example3) The dynamic equivalent load P of spherical roller
bearings is given by: 50
Obtain C r / P or fatigue life factor fh when an axial Bearing I Bearing II
load Fa=1 000N, {102kgf} is added to the conditions of HR30305DJ 40 10 HR30206J
(Example1) when Fa / Fre
Obtain the fatigue life factor f h of single-row deep (Example 1)
groove ball bearing 6208 when it is used under P = XFr + YXa = Fr + Y3 Fa
a radial load F r =2 500 N, {255kgf} and speed When the radial load Fr and axial load Fa are applied on
when Fa / Fr>e 59.9 23.9
n =900 min1. single-row deep groove ball bearing 6208, the dynamic
equivalent load P should be calculated in accordance P = XFr + YFa = 0.67 Fr + Y2 Fa 2000N, {204kgf} 83.8
with the following procedure.
The basic load rating C r of 6208 is 29 100N, {2 970kgf} Fa / Fr = 8 000/45 000 = 0.18
Obtain the radial load factor X, axial load factor Y and 5500N
(Bearing Table, Page B10). Since only a radial load constant e obtainable, depending on the magnitude We can see in the bearing table that the value of e is {561kgf}
is applied, the equivalent load P may be obtained as of fo Fa /C or, from the table above the single-row deep about 0.3 and that of Y3 is about 2.2 for bearings of
follows: groove ball bearing table. series 231: Fig. 5.14 Loads on Tapered Roller Bearings
P = Fr = 2 500N, {255kgf} The basic static load rating C or of ball bearing 6208 is Therefore, P = XFr + YFa = Fr + Y3 Fa
Since the speed is n = 900 min1, the speed factor fn 17 900N, {1 820kgf} (Page B10)
= 45 000 + 2.2 8 000
can be obtained from the equation in Table 5.2 (Page To distribute the radial load Fr on bearings1and 2, the
A25) or Fig. 5.3(Page A26). fo Fa /C or = 14.0 1 000/17 900 = 0.782 = 62 600N, {6 380kgf}
effective load centers must be located for tapered roller
fn = 0.333 eH0.26 bearings. Obtain the effective load center a for bearings
From the fatigue life factor fh, the basic load rating can 1and 2 from the bearing table, then obtain the relative
The fatigue life factor fh, under these conditions, can be and Fa / Fr = 1 000/2 500 = 0.4>e be obtained as follows:
calculated as follows: position of the radial load Fr and effective load centers.
X = 0.56 The result will be as shown in Fig. 5.14. Consequently,
fh = fn C r = 0.444 C r 3.45
fh = fn C r = 0.333 29 100 = 3.88 Y = 1.67 (the value of Y is obtained by linear P 62 600
the radial load applied on bearings1 (HR30305DJ) and
P 2 500 2 (HR30206J) can be obtained from the following
interpolation)
This value is suitable for industrial applications, air consequently, C r490 000N, {50 000kgf} equations:
conditioners being regularly used, etc., and according Therefore, the dynamic equivalent load P is
Among spherical roller bearings of series 231 satisfying
to the equation in Table 5.2 or Fig. 5.4 (Page A26), it P = XFr + YFa this value of C r, the smallest is 23126CE4 Fr1 = 5 500 23.9 = 1 569N, {160kgf}
corresponds approximately to 29 000 hours of service 83.8
= 0.56 2 500 + 1.67 1 000 (C r = 505 000N, {51 500kgf})
life. Once the bearing is determined, substitude the value of Fr2 = 5 500 59.9 = 3 931N, {401kgf}
= 3 070N, {313kgf} Y3 in the equation and obtain the value of P. 83.8
(Example 2) C r = 29 100 = 9.48 P = Fr + Y3 Fa = 45 000 + 2.4 8 000 From the data in the bearing table, the following values
Select a single-row deep groove ball bearing with a P 3 070 = 64 200N, {6 550kgf} are obtained;
bore diameter of 50 mm and outside diameter under
100 mm that satisfies the following conditions: fh = fn C r = 0.333 29 100 = 3.16 Cr
10
Radial load Fr = 3 000N, {306kgf} P 3 070 ( )

Lh = 500 fn P 3 Basic dynamic
load rating
Axial load
factor
Constant
10 Bearings
This value of fh corresponds approximately to 15 800 505 000 Cr Y1 e
Speed n =1 900 min1 = 500 (0.444 ) 3
(N) {kgf}
hours for ball bearings. 64 200
Basic rating life Lh10 000h 10
= 500 3.49 3 H32 000 h Bearing 1 (HR30305DJ) 38 000 {3 900} Y1 = 0.73 0.83
The fatigue life factor fh of ball bearings with a rating (Example 4) Bearing 2 (HR30206J) 43 000 {4 400} Y2 = 1.60 0.38
fatigue life longer than 10 000 hours is fh2.72. Select a spherical roller bearing of series 231
satisfying the following conditions: (Example 5)
Because fn = 0.26, P = Fr = 3 000N. {306kgf} Assume that tapered roller bearings HR30305DJ and
Radial load Fr = 45 000N, {4 950kgf} When radial loads are applied on tapered roller
Cr HR30206J are used in a back-to-back arrangement
fh = fn C r = 0.26 2.72 Axial load Fa = 8 000N, {816kgf} as shown in Fig. 5.14, and the distance between the
bearings, an axial load component is produced, which
P 3 000 must be considered to obtain the dynamic equivalent
Speed n = 500min1 cup back faces is 50 mm. radial load (Refer to Paragraph 5.4.2, Page A31).
Calculate the basic rating life of each bearing when
therefore, C r2.72 3 000 = 31 380N, {3 200kgf} Basic rating life Lh30 000h
0.26 beside the radial load Fr = 5 500N, {561kgf},
axial load Fae =2 000N, {204kgf} are applied to
Among the data listed in the bearing table on Page
HR30305DJ as shown in Fig. 5.14. The speed is
B12, 6210 should be selected as one that satisfies the The value of the fatigue life factor fh which makes 600 min1.
above conditions. Lh30 000h is bigger than 3.45 from Fig. 5.4 (Page
A26).
A 34 A 35
A024-057E.indd 34-35 11/20/13 4:50:17 PM

6. LIMITING SPEED
Fae + 0.6 Fr2 = 2 000 + 0.6 3 931 In this application, heavy loads, shocks, and shaft The speed of rolling bearings is subject to certain 6.2 Limiting Speed for Rubber Contact Seals
Y2 1.6 deflection are expected; therefore, spherical roller limits. When bearings are operating, the higher the for Ball Bearings
= 3 474N, {354kgf} bearings are appropriate. speed, the higher the bearing temperature due to The maximum permissible speed for contact rubber
The following spherical roller bearings satisfy the friction. The limiting speed is the empirically obtained sealed bearings (DDU type) is determined mainly by
0.6 F = 0.6 1 569 = 1 290N, above size limitation (refer to Page B196) value for the maximum speed at which bearings can be
Y1 r1 0.73
{132kgf} the sliding surface speed of the inner circumference of
continuously operated without failing from seizure or the seal. Values for the limiting speed are listed in the
Basic dynamic Constant Factor generation of excessive heat. Consequently, the limiting bearing tables.
Therefore, with this bearing arrangement, the axial load rating speed of bearings varies depending on such factors
0.6 d D B Bearing No.
Cr e Y3
load Fae + F is applied on bearing1but not on as bearing type and size, cage form and material,
Y2 r2 (N) {kgf} load, lubricating method, and heat dissipating method
bearing 2. 300 420 90 23960 CAE4 1 230 000 125 000 0.19 3.5 including the design of the bearing's surroundings. 1.0
For bearing1 460 118 23060 CAE4 1 920 000 196 000 0.24 2.8 The limiting speeds for bearings lubricated by grease
Fr1 = 1 569N, {160kgf} 460 160 24060 CAE4 2 310 000 235 000 0.32 2.1 and oil are listed in the bearing tables. The limiting 0.9
speeds in the tables are applicable to bearings of
Correction Factor
Fa1 = 3 474N, {354kgf} 500 160 23160 CAE4 2 670 000 273 000 0.31 2.2 standard design and subjected to normal loads, i. e. 0.8
500 200 24160 CAE4 3 100 000 315 000 0.38 1.8 C/P12 and Fa /Fr 0.2 approximately. The limiting
since Fa1 / Fr1 = 2.2>e = 0.83
speeds for oil lubrication listed in the bearing tables 0.7
the dynamic equivalent load P1 = XFr1 + Y1Fa1 since Fa / Fr = 0.20<e are for conventional oil bath lubrication.
= 0.4 1 569 + 0.73 3 474 the dynamic equivalent load P is Some types of lubricants are not suitable for high 0.6
speed, even though they may be markedly superior
= 3 164N, {323kgf}
P = Fr + Y3 Fa in other respects. When speeds are more than 70 4 5 7 6 8 9 10 11 12
The fatigue life factor f h = fn Cr percent of the listed limiting speed, it is necessary C/P
P1 Judging from the fatigue life factor f h in Table 5.1 and to select an oil or grease which has good high speed Fig. 6.1 Limiting Speed Correction Factor Variation with
= 0.42 38 000 = 5.04 examples of applications (refer to Page A25), a value characteristics. Load Ratio
3 164 of f h, between 3 and 5 seems appropriate.
10
(Refer to)
and the rating fatigue life L h = 500 5.04 3 = 109 f h = fn Cr = 0.444 Cr = 3 to 5 Angular Contact Ball Brgs.
750h P Fr + Y3 Fa Table 12.2 Grease Properties (Pages A110 and 111) 1.0
Table 12.5 Example of Selection of Lubricant for Bearing
Deep Groove Ball Brgs
For bearing 2 Assuming that Y3 = 2.1, then the necessary basic load Operating Conditions (Page A113) 0.9
Correction Factor
since Fr2 = 3 931N, {401kgf}, Fa2 = 0 rating C r can be obtained Table 15.8 Brands and Properties of Lubricating Grease
(Pages A138 to A141) 0.8
Cr = (Fr + Y3 Fa ) (3 to 5)
the dynamic equivalent load
Spherical Roller Brgs.
P2 = Fr2 = 3 931N, {401kgf} 0.444 6.1 Correction of Limiting Speed 0.7
Tapered Roller Brgs.
the fatigue life factor When the bearing load P exceeds 8 % of the basic load
= (245 000 + 2.1 49 000) (3 to 5)
0.6
rating C, or when the axial load Fa exceeds 20 % of
f h = fn C r = 0.42 43 000 = 4.59
0.444 the radial load Fr, the limiting speed must be corrected 0.5
P2 3 931 by multiplying the limiting speed found in the bearing 0 1.0 0.5 1.5 2.0
10 = 2 350 000 to 3 900 000 N, tables by the correction factor shown in Figs. 6.1 and Fa /F r
and the rating fatigue life Lh = 500 4.59 3 = 80 400h {240 000 to 400 000 kgf} 6.2. Fig. 6.2 Limiting Speed Correction Factor for Combined Radial
are obtained. When the required speed exceeds the limiting speed of and Axial Loads
The bearings which satisfy this range are 23160CAE4, the desired bearing; then the accuracy grade, internal
Remarks For face-to-face arrangements (DF type), and 24160CAE4. clearance, cage type and material, lubrication, etc.,
please contact NSK. Table 6.1 Limiting Speed Correction Factor for
must be carefully studied in order to select a bearing High-Speed Applications
capable of the required speed. In such a case, forced-
circulation oil lubrication, jet lubrication, oil mist Bearing Types
Correction
(Example 6) lubrication, or oil-air lubrication must be used. Factor
Select a bearing for a speed reducer under the If all these conditions are considered. The maximum
following conditions: permissible speed may be corrected by multiplying
Operating conditions Cylindrical Roller Brgs.(single row) 2
the limiting speed found in the bearing tables
Radial load Fr = 245 000N, {25 000kgf} by the correction factor shown in Table 6.1. It is Needle Roller Brgs.(except broad width) 2
Axial load Fa = 49 000N, {5 000kgf} recommended that NSK be consulted regarding high Tapered Roller Brgs. 2
speed applications.
Speed n = 500min1 Spherical Roller Brgs. 1.5
Size limitation Deep Grooove Ball Brgs. 2.5
Shaft diameter: 300mm
Bore of housing: Less than 500mm Angular Contact Ball Brgs.(except matched bearings) 1.5
A 36 A 37
A024-057E.indd 36-37 11/20/13 4:50:19 PM

7. BOUNDARY DIMENSIONS AND IDENTIFYING NUMBERS FOR BEARINGS
7.1 Boundary Dimensions and Dimensions of 7.1.2 Dimensions of Snap Ring Grooves and T
Snap Ring Grooves Locating Snap Rings Diameter
C Series
7.1.1 Boundary Dimensions The dimensions of Snap ring grooves in the outer r r1 Height
01 2 3 4 Series
The boundary dimensions of rolling bearings, which surfaces of bearings are specified by ISO 464. Also, Dimension series
are shown in Figs.7.1 through 7.5, are the dimensions the dimensions and accuracy of the locating snap rings r r1 70
that define their external geometry. They include bore themselves are specified by ISO 464. The dimensions 71
of snap ring grooves and locating snap ring for 72
diameter d, outside diameter D, width B, bearing r1 r 73 7
width(or height) T, chamfer dimension r, etc. It is bearings of diameter series 8, 9, 0, 2, 3, and 4, are
necessary to know all of these dimensions when shown in Table 7.4 (Pages A50 to A53). r1 r 74
jd jD
mounting a bearing on a shaft and in a housing. B 90
These boundary dimensions have been internationally 91
standardized (ISO15) and adopted by JIS B 1512 92 9
(Boundary Dimensions of Rolling Bearings). 93
The boundary dimensions and dimension series of B
radial bearings, tapered roller bearings, and thrust 94
r r Fig. 7.2 Tapered Roller Bearings
bearings are listed in Table 7.1 to 7.3 (Pages A40 to
10
A49). 11
In these boundary dimension tables, for each bore r r 1
12
number, which prescribes the bore diameter, other
boundary dimensions are listed for each diameter jd r 13
series and dimension series. A very large number r r
of series are possible; however, not all of them are r
14
commercially available so more can be added in the T
future. Across the top of each bearing table (7.1 to r r jd jD r
7.3), representative bearing types and series symbols
are shown (refer to Table 7.5, Bearing Series Symbols, r
Page A55). 2
jD
The relative cross-sectional dimensions of radial
bearings (except tapered roller bearings) and thrust Fig. 7.3 Single-Direction Thrust Ball Bearings 22
bearings for the various series classifications are
shown in Figs. 7.6 and 7.7 respectively. 23
r
Fig. 7.1 Boundary Dimensions of Radial Ball jd
and Roller Bearings r
r1 24
T2
r1
jd 2 B T1
r1
T2 Fig. 7.7 Comparison of Cross Sections of Thrust Bearings
r1 (except Diameter Series 5) for Various
r
Width Series 8 0 1 2 3 4 5 6 Dimension Series
4 r
jD
Diameter
3
Series
2
10 Fig. 7.4 Double-Direction Thrust Ball Bearings
9
8
21
12
11
Dimension
02
83
20
00
22
19 10
38
48
49
41
58
59
50
68
69
60
03
23
24
30
32
33
40
42
04
39
Series
31
13
r
01
29
jd
08 09
82
18
28
r
T
r
r
jD
Fig. 7.6 Comparison of Cross Sections of Radial Bearings (except Tapered Roller Bearings) for various Dimensional Series
Fig. 7.5 Spherical Thrust Roller Bearings
A 38 A 39
A024-057E.indd 38-39 11/20/13 4:50:20 PM

Table 7. 1 Boundary Dimensions of Radial Bearings (except Tapered Roller Bearings) 1
A 40
Units: mm
Single-Row 69 60
Ball Brgs. 68 79 160 70
Double-Row Ball
Brgs.
Cylindrical Roller
Brgs. N28 NN38 NN48 N19 N29 NN39 NN49 N10 N20 NN30 NN40
Needle Roller
A024-057E.indd 40-41
Brgs. NA48 NA49 NA59 NA69
Spherical Roller
Brgs. 239 230 240
Diameter Series 7 Diameter Series 8 Diameter Series 9 Diameter Series 0

Dimension Dimension
Dimension Series Dimension Series Series Dimension Series Dimension Series Dimension Series Series
d D 17 27 37 17~37 D 08 18 28 38 48 58 68 08 18~68 D 09 19 29 39 49 59 69 09 19~39 49~69 D 00 10 20 30 40 50 60 00 10~60
Bore Number
r
B (min.) B r (min.) B r (min.) B r (min.)
0.6 2 0.8 0.05 2.5 01 01.4 0.05
1 1 2.5 1 0.05 3 01 01.5 0.05 4 01.6 02.3 0.1
1.5 3 1 1.8 0.05 4 01.2 02 0.05 5 02 02.6 0.15 6 02.5 03 0.15
2 2 4 1.2 2 0.05 5 01.5 02.3 0.08 6 02.3 03 0.15 7 02.8 03.5 0.15
2.5 5 1.5 2.3 0.08 6 01.8 02.6 0.08 7 02.5 03.5 0.15 8 02.8 04 0.15
3 3 6 2 2.5 3 0.08 7 02 03 0.1 8 03 04 0.15 9 03 05 0.15
4 4 7 2 2.5 3 0.08 9 02.5 03.5 04 0.1 11 04 05 0.15 12 04 06 0.2
5 5 8 2 2.5 3 0.08 11 03 04 05 0.15 13 04 06 10 0.2 0.15 14 05 07 0.2
6 6 10 2.5 3 3.5 0.1 13 03.5 05 06 0.15 15 05 07 10 0.2 0.15 17 06 09 0.3
7 7 11 2.5 3 3.5 0.1 14 03.5 05 06 0.15 17 05 07 10 0.3 0.15 19 06 8 10 0.3
8 8 12 2.5 3.5 0.1 16 04 05 06 8 0.2 19 06 09 11 0.3 0.2 22 07 9 11 14 19 25 0.3
9 9 14 3 4.5 0.1 17 04 05 06 8 0.2 20 06 09 11 0.3 0.3 24 07 10 12 15 20 27 0.3
00 10 15 3 4.5 0.1 19 05 06 07 9 0.3 22 06 8 10 13 16 22 0.3 0.3 26 08 10 12 16 21 29 0.3
01 12 18 4 5 0.2 21 05 06 07 9 0.3 24 06 8 10 13 16 22 0.3 0.3 28 7 08 10 12 16 21 29 0.3 0.3
02 15 21 4 5 0.2 24 05 06 07 9 0.3 28 07 8.5 10 13 18 23 0.3 0.3 32 8 09 11 13 17 23 30 0.3 0.3
03 17 23 4 5 0.2 26 05 06 07 9 0.3 30 07 8.5 10 13 18 23 0.3 0.3 35 8 10 12 14 18 24 32 0.3 0.3
04 20 27 4 5 0.2 32 4 07 08 10 12 16 22 0.3 0.3 37 7 09 11 13 17 23 30 0.3 0.3 0.3 42 8 12 14 16 22 30 40 0.3 0.6
/22 22 34 4 07 10 16 22 0.3 0.3 39 7 09 11 13 17 23 30 0.3 0.3 0.3 44 8 12 14 16 22 30 40 0.3 0.6
05 25 32 4 5 0.2 37 4 07 08 10 12 16 22 0.3 0.3 42 7 09 11 13 17 23 30 0.3 0.3 0.3 47 8 12 14 16 22 30 40 0.3 0.6
/28 28 40 4 07 10 16 22 0.3 0.3 45 7 09 11 13 17 23 30 0.3 0.3 0.3 52 8 12 15 18 24 32 43 0.3 0.6
06 30 37 4 5 0.2 42 4 07 08 10 12 16 22 0.3 0.3 47 7 09 11 13 17 23 30 0.3 0.3 0.3 55 9 13 16 19 25 34 45 0.3 1
/32 32 44 4 07 10 16 22 0.3 0.3 52 7 10 13 15 20 27 36 0.3 0.6 0.6 58 9 13 16 20 26 35 47 0.3 1
07 35 47 4 07 08 10 12 16 22 0.3 0.3 55 7 10 13 15 20 27 36 0.3 0.6 0.6 62 9 14 17 20 27 36 48 0.3 1
08 40 52 4 07 08 10 12 16 22 0.3 0.3 62 8 12 14 16 22 30 40 0.3 0.6 0.6 68 9 15 18 21 28 38 50 0.3 1
BOUNDARY DIMENSIONS AND IDENTIFYING NUMBERS FOR BEARINGS
09 45 58 4 07 08 10 13 18 23 0.3 0.3 68 8 12 14 16 22 30 40 0.3 0.6 0.6 75 10 16 19 23 30 40 54 0.6 1

10 50 65 5 07 10 12 15 20 27 0.3 0.3 72 8 12 14 16 22 30 40 0.3 0.6 0.6 80 10 16 19 23 30 40 54 0.6 1
11 55 72 7 09 11 13 17 23 30 0.3 0.3 80 9 13 16 19 25 34 45 0.3 1 1 90 11 18 22 26 35 46 63 0.6 1.1
12 60 78 7 10 12 14 18 24 32 0.3 0.3 85 9 13 16 19 25 34 45 0.3 1 1 95 11 18 22 26 35 46 63 0.6 1.1
13 65 85 7 10 13 15 20 27 36 0.3 0.6 90 9 13 16 19 25 34 45 0.3 1 1 100 11 18 22 26 35 46 63 0.6 1.1
14 70 90 8 10 13 15 20 27 36 0.3 0.6 100 10 16 19 23 30 40 54 0.6 1 1 110 13 20 24 30 40 54 71 0.6 1.1
15 75 95 8 10 13 15 20 27 36 0.3 0.6 105 10 16 19 23 30 40 54 0.6 1 1 115 13 20 24 30 40 54 71 0.6 1.1
16 80 100 8 10 13 15 20 27 36 0.3 0.6 110 10 16 19 23 30 40 54 0.6 1 1 125 14 22 27 34 45 60 80 0.6 1.1
17 85 110 9 13 16 19 25 34 45 0.3 1 120 11 18 22 26 35 46 63 0.6 1.1 1.1 130 14 22 27 34 45 60 80 0.6 1.1
18 90 115 9 13 16 19 25 34 45 0.3 1 125 11 18 22 26 35 46 63 0.6 1.1 1.1 140 16 24 30 37 50 67 90 1 1.5
19 95 120 9 13 16 19 25 34 45 0.3 1 130 11 18 22 26 35 46 63 0.6 1.1 1.1 145 16 24 30 37 50 67 90 1 1.5
20 100 125 9 13 16 19 25 34 45 0.3 1 140 13 20 24 30 40 54 71 0.6 1.1 1.1 150 16 24 30 37 50 67 90 1 1.5
21 105 130 9 13 16 19 25 34 45 0.3 1 145 13 20 24 30 40 54 71 0.6 1.1 1.1 160 18 26 33 41 56 75 100 1 02

22 110 140 10 16 19 23 30 40 54 0.6 1 150 13 20 24 30 40 54 71 0.6 1.1 1.1 170 19 28 36 45 60 80 109 1 02
24 120 150 10 16 19 23 30 40 54 0.6 1 165 14 22 27 34 45 60 80 0.6 1.1 1.1 180 19 28 36 46 60 80 109 1 02
26 130 165 11 18 22 26 35 46 63 0.6 1.1 180 16 24 30 37 50 67 90 1 1.5 1.5 200 22 33 42 52 69 95 125 1.1 02
28 140 175 11 18 22 26 35 46 63 0.6 1.1 190 16 24 30 37 50 67 90 1 1.5 1.5 210 22 33 42 53 69 95 125 1.1 02
30 150 190 13 20 24 30 40 54 71 0.6 1.1 210 19 28 36 45 60 80 109 1 2 2 225 24 35 45 56 75 100 136 1.1 02.1
32 160 200 13 20 24 30 40 54 71 0.6 1.1 220 19 28 36 45 60 80 109 1 2 2 240 25 38 48 60 80 109 145 1.5 02.1
34 170 215 14 22 27 34 45 60 80 0.6 1.1 230 19 28 36 45 60 80 109 1 2 2 260 28 42 54 67 90 122 160 1.5 02.1
36 180 225 14 22 27 34 45 60 80 0.6 1.1 250 22 33 42 52 69 95 125 1.1 2 2 280 31 46 60 74 100 136 180 2 02.1
38 190 240 16 24 30 37 50 67 90 1 1.5 260 22 33 42 52 69 95 125 1.1 2 2 290 31 46 60 75 100 136 180 2 02.1
40 200 250 16 24 30 37 50 67 90 1 1.5 280 25 38 48 60 80 109 145 1.5 2.1 2.1 310 34 51 66 82 109 150 200 2 02.1
44 220 270 16 24 30 37 50 67 90 1 1.5 300 25 38 48 60 80 109 145 1.5 2.1 2.1 340 37 56 72 90 118 160 218 2.1 03
48 240 300 19 28 36 45 60 80 109 1 2 320 25 38 48 60 80 109 145 1.5 2.1 2.1 360 37 56 72 92 118 160 218 2.1 03
52 260 320 19 28 36 45 60 80 109 1 2 360 31 46 60 75 100 136 180 2 2.1 2.1 400 44 65 82 104 140 190 250 3 04
56 280 350 22 33 42 52 69 95 125 1.1 2 380 31 46 60 75 100 136 180 2 2.1 2.1 420 44 65 82 106 140 190 250 3 04
60 300 380 25 38 48 60 80 109 145 1.5 2.1 420 37 56 72 90 118 160 218 2.1 3 3 460 50 74 95 118 160 218 290 4 04
64 320 400 25 38 48 60 80 109 145 1.5 2.1 440 37 56 72 90 118 160 218 2.1 3 3 480 50 74 95 121 160 218 290 4 04
68 340 420 25 38 48 60 80 109 145 1.5 2.1 460 37 56 72 90 118 160 218 2.1 3 3 520 57 82 106 133 180 243 325 4 05
72 360 440 25 38 48 60 80 109 145 1.5 2.1 480 37 56 72 90 118 160 218 2.1 3 3 540 57 82 106 134 180 243 325 4 05
76 380 480 31 46 60 75 100 136 180 2 2.1 520 44 65 82 106 140 190 250 3 4 4 560 57 82 106 135 180 243 325 4 05
80 400 500 31 46 60 75 100 136 180 2 2.1 540 44 65 82 106 140 190 250 3 4 4 600 63 90 118 148 200 272 355 5 05
84 420 520 31 46 60 75 100 136 180 2 2.1 560 44 65 82 106 140 190 250 3 4 4 620 63 90 118 150 200 272 355 5 05
88 440 540 31 46 60 75 100 136 180 2 2.1 600 50 74 95 118 160 218 290 4 4 4 650 67 94 122 157 212 280 375 5 06
92 460 580 37 56 72 90 118 160 218 2.1 3 620 50 74 95 118 160 218 290 4 4 4 680 71 100 128 163 218 300 400 5 06
96 480 600 37 56 72 90 118 160 218 2.1 3 650 54 78 100 128 170 230 308 4 5 5 700 71 100 128 165 218 300 400 5 06
/500 500 620 37 56 72 90 118 160 218 2.1 3 670 54 78 100 128 170 230 308 4 5 5 720 71 100 128 167 218 300 400 5 06
/530 530 650 37 56 72 90 118 160 218 2.1 3 710 57 82 106 136 180 243 325 4 5 5 780 80 112 145 185 250 335 450 6 06
/560 560 680 37 56 72 90 118 160 218 2.1 3 750 60 85 112 140 190 258 345 5 5 5 820 82 115 150 195 258 355 462 6 06
/600 600 730 42 60 78 98 128 175 236 3 3 800 63 90 118 150 200 272 355 5 5 5 870 85 118 155 200 272 365 488 6 06
/630 630 780 48 69 88 112 150 200 272 3 4 850 71 100 128 165 218 300 400 5 6 6 920 92 128 170 212 290 388 515 6 07.5
/670 670 820 48 69 88 112 150 200 272 3 4 900 73 103 136 170 230 308 412 5 6 6 980 100 136 180 230 308 425 560 6 07.5
/710 710 870 50 74 95 118 160 218 290 4 4 950 78 106 140 180 243 325 438 5 6 6 1030 103 140 185 236 315 438 580 6 07.5
/750 750 920 54 78 100 128 170 230 308 4 5 1000 80 112 145 185 250 335 450 6 6 6 1090 109 150 195 250 335 462 615 7.5 07.5
/800 800 980 57 82 106 136 180 243 325 4 5 1060 82 115 150 195 258 355 462 6 6 6 1150 112 155 200 258 345 475 630 7.5 07.5
/850 850 1030 57 82 106 136 180 243 325 4 5 1120 85 118 155 200 272 365 488 6 6 6 1220 118 165 212 272 365 500 670 7.5 07.5
/900 900 1090 60 85 112 140 190 258 345 5 5 1180 88 122 165 206 280 375 500 6 6 6 1280 122 170 218 280 375 515 690 7.5 07.5
/950 950 1150 63 90 118 150 200 272 355 5 5 1250 95 132 175 224 300 400 545 6 7.5 7.5 1360 132 180 236 300 412 560 730 7.5 07.5
/1000 1000 1220 71 100 128 165 218 300 400 5 6 1320 103 140 185 236 315 438 580 6 7.5 7.5 1420 136 185 243 308 412 560 750 7.5 07.5
/1060 1060 1280 71 100 128 165 218 300 400 5 6 1400 109 150 195 250 335 462 615 7.5 7.5 7.5 1500 140 195 250 325 438 600 800 9.5 09.5
/1120 1120 1360 78 106 140 180 243 325 438 5 6 1460 109 150 195 250 335 462 615 7.5 7.5 7.5 1580 145 200 265 345 462 615 825 9.5 09.5
/1180 1180 1420 78 106 140 180 243 325 438 5 6 1540 115 160 206 272 355 488 650 7.5 7.5 7.5 1660 155 212 272 355 475 650 875 9.5 09.5
/1250 1250 1500 80 112 145 185 250 335 450 6 6 1630 122 170 218 280 375 515 690 7.5 7.5 7.5 1750 218 290 375 500 09.5
/1320 1320 1600 88 122 165 206 280 375 500 6 6 1720 128 175 230 300 400 545 710 7.5 7.5 7.5 1850 230 300 400 530 12
/1400 1400 1700 95 132 175 224 300 400 545 6 7.5 1820 185 243 315 425 9.5 9.5 1950 243 315 412 545 12
/1500 1500 1820 140 185 243 315 7.5 1950 195 258 335 450 9.5 9.5 2120 272 355 462 615 12
/1600 1600 1950 155 200 265 345 7.5 2060 200 265 345 462 9.5 9.5 2240 280 365 475 630 12
/1700 1700 2060 160 206 272 355 7.5 2180 212 280 355 475 9.5 9.5 2360 290 375 500 650 15
/1800 1800 2180 165 218 290 375 9.5 2300 218 290 375 500 12 12 2500 308 400 530 690 15
/1900 1900 2300 175 230 300 400 9.5 2430 230 308 400 530 12 12
/2000 2000 2430 190 250 325 425 9.5
Remarks The chamfer dimensions listed in this table do not necessarily apply to the following chamfers: (a) Chamfers of the grooves in outer rings that have snap ring grooves.
(b) For thin section cylindrical roller bearings, the chamfers on side without rib and bearing bore (in case of an inner ring) or outer surface (in case of an outer ring).
(c) For angular contact ball bearings, the chamfers between the front face and bore (in case of an inner ring) or outer surface (in case of an outer ring).
A 41
(d) Chamfers on inner rings of bearings with tapered bores.

11/20/13 4:50:21 PM
Table 7. 1 Boundary Dimensions of Radial Bearings (except Tapered Roller Bearings) 2
A 42
Units: mm
Single-Row 62 63 64
Ball Brgs. 622 632 623 633
72 73 74
Double-Row 42 52 43 53
Ball Brgs. 12 13 104
22 53 23 33
Cylindrical
Roller Brgs. NN 31 N2 N 22 N 32 N3 N 23 N 33 N4
A024-057E.indd 42-43
Needle Roller
Brgs.
Spherical Roller
Brgs. 231 241 222 232 213 223
Diameter Series 1 Diameter Series 2 Diameter Series 3 Diameter Series 4

Dimension Dimension Dimension Dimension Dimension
Dimension Series Dimension Series Dimension Series Series
Series Series Series Series
d D 01 11 21 31 41 01 11~41 D 82 02 12 22 32 42 82 02~42 D 83 03 13 23 33 83 03~33 D 04 24 04~24
Bore Number
B r (min.) B r (min.) B r (min.) B r
(min.)
0.6
1 1
1.5
2 2
2.5
3 3 10 02.5 4 05 0.1 0.15 13 5 07 0.2
4 4 13 03 5 07 0.15 0.2 16 5 09 0.3
5 5 7 16 03.5 5 08 0.15 0.3 19 6 10 0.3
6 6 8 10 19 04 6 10 0.2 0.3 22 7 11 13 0.3
7 7 9 11 14 22 05 7 11 0.3 0.3 26 9 13 15 0.3
8 8 10 12 15 24 05 8 12 0.3 0.3 28 9 13 15 0.3 30 10 14 0.6
9 9 10 12 16 26 06 8 13 0.3 0.3 30 10 14 16 0.6 32 11 15 0.6
00 10 12 14 18 30 07 9 14 14.3 0.3 0.6 35 9 11 17 19 0.3 0.6 37 12 16 0.6
01 12 12 14 18 32 07 10 14 15.9 0.3 0.6 37 9 12 17 19 0.3 1 42 13 19 1
02 15 12 14 18 35 08 11 14 15.9 20 0.3 0.6 42 9 13 17 19 0.3 1 52 15 24 1.1
03 17 13 15 20 40 08 12 16 17.5 22 0.3 0.6 47 10 14 19 22.2 0.6 1 62 17 29 1.1
04 20 15 18 24 47 09 14 18 20.6 27 0.3 1 52 10 15 21 22.2 0.6 1.1 72 19 33 1.1
/22 22 16 19 25 50 09 14 18 20.6 27 0.3 1 56 11 16 21 25 0.6 1.1
05 25 16 19 25 52 10 15 18 20.6 27 0.3 1 62 12 17 24 25.4 0.6 1.1 80 21 36 1.5
/28 28 17 20 27 58 10 16 19 23 30 0.6 1 68 13 18 24 30 0.6 1.1
06 30 18 21 28 62 10 16 20 23.8 32 0.6 1 72 13 19 27 30.2 0.6 1.1 90 23 40 1.5
/32 32 19 23 30 65 11 17 21 25 33 0.6 1 75 14 20 28 32 0.6 1.1
07 35 21 25 33 72 12 17 23 27 37 0.6 1.1 80 14 21 31 34.9 0.6 1.5 100 25 43 1.5
08 40 22 26 35 80 13 18 23 30.2 40 0.6 1.1 90 16 23 33 36.5 1 1.5 110 27 46 2
09 45 22 26 35 85 13 19 23 30.2 40 0.6 1.1 100 17 25 36 39.7 1 1.5 120 29 50 2

10 50 22 26 35 90 13 20 23 30.2 40 0.6 1.1 110 19 27 40 44.4 1 2 130 31 53 2.1
11 55 24 30 40 100 14 21 25 33.3 45 0.6 1.5 120 21 29 43 49.2 1.1 2 140 33 57 2.1
12 60 24 30 40 110 16 22 28 36.5 50 1 1.5 130 22 31 46 54 1.1 2.1 150 35 60 2.1
13 65 27 34 45 120 18 23 31 38.1 56 1 1.5 140 24 33 48 58.7 1.1 2.1 160 37 64 2.1
14 70 27 34 45 125 18 24 31 39.7 56 1 1.5 150 25 35 51 63.5 1.5 2.1 180 42 74 3
15 75 30 37 50 130 18 25 31 41.3 56 1 1.5 160 27 37 55 68.3 1.5 2.1 190 45 77 3
16 80 30 37 50 140 19 26 33 44.4 60 1 2 170 28 39 58 68.3 1.5 2.1 200 48 80 3
17 85 31 41 56 150 21 28 36 49.2 65 1.1 2 180 30 41 60 73 2 3 210 52 86 4
18 90 150 33 45 60 2 160 22 30 40 52.4 69 1.1 2 190 30 43 64 73 2 3 225 54 90 4
19 95 160 39 52 65 2 170 24 32 43 55.6 75 1.1 2.1 200 33 45 67 77.8 2 3 240 55 95 4
20 100 165 21 30 39 52 65 1.1 2 180 25 34 46 60.3 80 1.5 2.1 215 36 47 51 73 82.6 2.1 3 250 58 98 4
21 105 175 22 33 42 56 69 01.1 02 190 27 36 50 065.1 85 1.5 02.1 225 37 49 53 77 087.3 2.1 03 260 60 100 04
22 110 180 22 33 42 56 69 01.1 02 200 28 38 53 069.8 90 1.5 02.1 240 42 50 57 80 092.1 3 03 280 65 108 04
24 120 200 25 38 48 62 80 01.5 02 215 40 42 58 076 95 02.1 260 44 55 62 86 106 3 03 310 72 118 05
26 130 210 25 38 48 64 80 01.5 02 230 40 46 64 080 100 03 280 48 58 66 93 112 3 04 340 78 128 05
28 140 225 27 40 50 68 85 01.5 02.1 250 42 50 68 088 109 03 300 50 62 70 102 118 4 04 360 82 132 05
30 150 250 31 46 60 80 100 02 02.1 270 45 54 73 096 118 03 320 65 75 108 128 04 380 85 138 05
32 160 270 34 51 66 86 109 02 02.1 290 48 58 80 104 128 03 340 68 79 114 136 04 400 88 142 05
34 170 280 34 51 66 88 109 02 02.1 310 52 62 86 110 140 04 360 72 84 120 140 04 420 92 145 05
36 180 300 37 56 72 96 118 02.1 03 320 52 62 86 112 140 04 380 75 88 126 150 04 440 95 150 06
38 190 320 42 60 78 104 128 03 03 340 55 65 92 120 150 04 400 78 92 132 155 05 460 98 155 06
40 200 340 44 65 82 112 140 03 03 360 58 70 98 128 160 04 420 80 97 138 165 05 480 102 160 06
44 220 370 48 69 88 120 150 03 04 400 65 78 108 144 180 04 460 88 106 145 180 05 540 115 180 06
48 240 400 50 74 95 128 160 04 04 440 72 85 120 160 200 04 500 95 114 155 195 05 580 122 190 06
52 260 440 57 82 106 144 180 04 04 480 80 90 130 174 218 05 540 102 123 165 206 06 620 132 206 07.5
56 280 460 57 82 106 146 180 04 05 500 80 90 130 176 218 05 580 108 132 175 224 06 670 140 224 07.5
60 300 500 63 90 118 160 200 05 05 540 85 98 140 192 243 05 620 109 140 185 236 07.5 710 150 236 07.5
64 320 540 71 100 128 176 218 05 05 580 92 105 150 208 258 05 670 112 155 200 258 07.5 750 155 250 09.5
68 340 580 78 106 140 190 243 05 05 620 92 118 165 224 280 06 710 118 165 212 272 07.5 800 165 265 09.5
72 360 600 78 106 140 192 243 05 05 650 95 122 170 232 290 06 750 125 170 224 290 07.5 850 180 280 09.5
76 380 620 78 106 140 194 243 05 05 680 95 132 175 240 300 06 780 128 175 230 300 07.5 900 190 300 09.5
80 400 650 80 112 145 200 250 06 06 720 103 140 185 256 315 06 820 136 185 243 308 07.5 950 200 315 12
84 420 700 88 122 165 224 280 06 06 760 109 150 195 272 335 07.5 850 136 190 250 315 09.5 980 206 325 12
88 440 720 88 122 165 226 280 06 06 790 112 155 200 280 345 07.5 900 145 200 265 345 09.5 1030 212 335 12
92 460 760 95 132 175 240 300 06 07.5 830 118 165 212 296 365 07.5 950 155 212 280 365 09.5 1060 218 345 12
96 480 790 100 136 180 248 308 06 07.5 870 125 170 224 310 388 07.5 980 160 218 290 375 09.5 1120 230 365 15
/500 500 830 106 145 190 264 325 07.5 07.5 920 136 185 243 336 412 07.5 1030 170 230 300 388 12 1150 236 375 15
/530 530 870 109 150 195 272 335 07.5 07.5 980 145 200 258 355 450 09.5 1090 180 243 325 412 12 1220 250 400 15
/560 560 920 115 160 206 280 355 07.5 07.5 1030 150 206 272 365 475 09.5 1150 190 258 335 438 12 1280 258 412 15
/600 600 980 122 170 218 300 375 07.5 07.5 1090 155 212 280 388 488 09.5 1220 200 272 355 462 15 1360 272 438 15
/630 630 1030 128 175 230 315 400 07.5 07.5 1150 165 230 300 412 515 12 1280 206 280 375 488 15 1420 280 450 15
/670 670 1090 136 185 243 336 412 07.5 07.5 1220 175 243 315 438 545 12 1360 218 300 400 515 15 1500 290 475 15
/710 710 1150 140 195 250 345 438 09.5 09.5 1280 180 250 325 450 560 12 1420 224 308 412 530 15
/750 750 1220 150 206 272 365 475 09.5 09.5 1360 195 265 345 475 615 15 1500 236 325 438 560 15
/800 800 1280 155 212 272 375 475 09.5 09.5 1420 200 272 355 488 615 15 1600 258 355 462 600 15
/850 850 1360 165 224 290 400 500 12 12 1500 206 280 375 515 650 15 1700 272 375 488 630 19
/900 900 1420 165 230 300 412 515 12 12 1580 218 300 388 515 670 15 1780 280 388 500 650 19
/950 950 1500 175 243 315 438 545 12 12 1660 230 315 412 530 710 15 1850 290 400 515 670 19
/1000 1000 1580 185 258 335 462 580 12 12 1750 243 330 425 560 750 15 1950 300 412 545 710 19
/1060 1060 1660 190 265 345 475 600 12 15
/1120 1120 1750 280 365 475 630 15
/1180 1180 1850 290 388 500 670 15
/1250 1250 1950 308 400 530 710 15
/1320 1320 2060 325 425 560 750 15
/1400 1400 2180 345 450 580 775 19
/1500 1500 2300 355 462 600 800 19
Remarks The chamfer dimensions listed in this table do not necessarily apply to the following chamfers: (a) Chamfers of the grooves in outer rings that have snap ring grooves.
(b) For thin section cylindrical roller bearings, the chamfers on side without rib and bearing bore (in case of an inner ring) or outer surface (in case of an outer ring).
(c) For angular contact ball bearings, the chamfers between the front face and bore (in case of an inner ring) or outer surface (in case of an outer ring).
(d) Chamfers on inner rings of bearings with tapered bores.
A 43
11/20/13 4:50:25 PM
Table 7. 2 Boundary Dimensions of Tapered Roller Bearings
Units: mm
Tapered Tapered
Roller 329 320 X 330 331 302 322 332 303 or 303D 313 323 Roller
Brgs. Brgs.
Diameter Series 9 Diameter Series 0 Diameter Series 1 Diameter Series 2 Diameter Series 3
Bore Number
Bore Number
Dimension Series 29 Chamfer Dimension Series Dimension Series Chamfer Dimension Series Chamfer Dimension Dimension Dimension Chamfer Dimension Series Dimension Dimension Chamfer
Dimension Dimension Dimension Dimension Dimension
d 1 2 Cone Cup 20 30 Cone Cup 31 Cone Cup Series 02 Series 22 Series 32 Cone Cup 03 Series 13 Series 23 Cone Cup d
D D D D D
B C T B C T r (min.) B C T B C T r (min.) B C T r (min.) B C T B C T B C T r (min.) B C C (1) T B C T B C T r (min.)
00 10 30 9 9.70 14 014.7 0.6 0.6 35 11 011.9 17 017.9 0.6 0.6 10 00

01 12 28 11 11 13 13 0.3 0.3 32 10 9 10.75 14 014.75 0.6 0.6 37 12 012.9 17 017.9 1 1 12 01
02 15 32 12 12 14 14 0.3 0.3 35 11 10 11.75 14 014.75 0.6 0.6 42 13 11 014.25 17 14 018.25 1 1 15 02
03 17 35 13 13 15 15 0.3 0.3 40 12 11 13.25 16 14 017.25 1 1 47 14 12 015.25 19 16 020.25 1 1 17 03

04 20 37 11 11.6 12 9 12 0.3 0.3 42 15 12 15 17 17 0.6 0.6 47 14 12 15.25 18 15 019.25 1 1 52 15 13 016.25 21 18 022.25 1.5 1.5 20 04
/22 22 40 12 9 12 0.3 0.3 44 15 11.5 15 0.6 0.6 50 14 12 15.25 18 15 019.25 1 1 56 16 14 017.25 21 18 022.25 1.5 1.5 22 /22
05 25 42 11 11.6 12 9 12 0.3 0.3 47 15 11.5 15 17 14 17 0.6 0.6 52 15 13 16.25 18 15 019.25 22 18 22 1 1 62 17 15 13 018.25 24 20 025.25 1.5 1.5 25 05
/28 28 45 12 9 12 0.3 0.3 52 16 12 16 1 1 58 16 14 17.25 19 16 020.25 24 19 24 1 1 68 18 15 14 019.75 24 20 025.75 1.5 1.5 28 /28
06 30 47 11 11.6 12 9 12 0.3 0.3 55 17 13 17 20 16 20 1 1 62 16 14 17.25 20 17 021.25 25 19.5 25 1 1 72 19 16 14 020.75 27 23 028.75 1.5 1.5 30 06
/32 32 52 15 10 14 0.6 0.6 58 17 13 17 1 1 65 17 15 18.25 21 18 022.25 26 20.5 26 1 1 75 20 17 15 021.75 28 24 029.75 1.5 1.5 32 /32
07 35 55 13 14 14 11.5 14 0.6 0.6 62 18 14 18 21 17 21 1 1 72 17 15 18.25 23 19 024.25 28 22 28 1.5 1.5 80 21 18 15 022.75 31 25 032.75 2 1.5 35 07
08 40 62 14 15 15 12 15 0.6 0.6 68 19 14.5 19 22 18 22 1 1 75 26 20.5 26 1.5 1.5 80 18 16 19.75 23 19 024.75 32 25 32 1.5 1.5 90 23 20 17 025.25 33 27 035.25 2 1.5 40 08
09 45 68 14 15 15 12 15 0.6 0.6 75 20 15.5 20 24 19 24 1 1 80 26 20.5 26 1.5 1.5 85 19 16 20.75 23 19 024.75 32 25 32 1.5 1.5 100 25 22 18 027.25 36 30 038.25 2 1.5 45 09
10 50 72 14 15 15 12 15 0.6 0.6 80 20 15.5 20 24 19 24 1 1 85 26 20 26 1.5 1.5 90 20 17 21.75 23 19 024.75 32 24.5 32 1.5 1.5 110 27 23 19 029.25 40 33 042.25 2.5 2 50 10
11 55 80 16 17 17 14 17 1 1 90 23 17.5 23 27 21 27 1.5 1.5 95 30 23 30 1.5 1.5 100 21 18 22.75 25 21 026.75 35 27 35 2 1.5 120 29 25 21 031.5 43 35 045.5 2.5 2 55 11
12 60 85 16 17 17 14 17 1 1 95 23 17.5 23 27 21 27 1.5 1.5 100 30 23 30 1.5 1.5 110 22 19 23.75 28 24 029.75 38 29 38 2 1.5 130 31 26 22 033.5 46 37 048.5 3 2.5 60 12
13 65 90 16 17 17 14 17 1 1 100 23 17.5 23 27 21 27 1.5 1.5 110 34 26.5 34 1.5 1.5 120 23 20 24.75 31 27 032.75 41 32 41 2 1.5 140 33 28 23 036 48 39 051 3 2.5 65 13
14 70 100 19 20 20 16 20 1 1 110 25 19 25 31 25.5 31 1.5 1.5 120 37 29 37 2 1.5 125 24 21 26.25 31 27 033.25 41 32 41 2 1.5 150 35 30 25 038 51 42 054 3 2.5 70 14
15 75 105 19 20 20 16 20 1 1 115 25 19 25 31 25.5 31 1.5 1.5 125 37 29 37 2 1.5 130 25 22 27.25 31 27 033.25 41 31 41 2 1.5 160 37 31 26 040 55 45 058 3 2.5 75 15
16 80 110 19 20 20 16 20 1 1 125 29 22 29 36 29.5 36 1.5 1.5 130 37 29 37 2 1.5 140 26 22 28.25 33 28 035.25 46 35 46 2.5 2 170 39 33 27 042.5 58 48 061.5 3 2.5 80 16
17 85 120 22 23 23 18 23 1.5 1.5 130 29 22 29 36 29.5 36 1.5 1.5 140 41 32 41 2.5 2 150 28 24 30.50 36 30 038.5 49 37 49 2.5 2 180 41 34 28 044.5 60 49 063.5 4 3 85 17
18 90 125 22 23 23 18 23 1.5 1.5 140 32 24 32 39 32.5 39 2 1.5 150 45 35 45 2.5 2 160 30 26 32.50 40 34 042.5 55 42 55 2.5 2 190 43 36 30 046.5 64 53 067.5 4 3 90 18
19 95 130 22 23 23 18 23 1.5 1.5 145 32 24 32 39 32.5 39 2 1.5 160 49 38 49 2.5 2 170 32 27 34.50 43 37 045.5 58 44 58 3 2.5 200 45 38 32 049.5 67 55 071.5 4 3 95 19
20 100 140 24 25 25 20 25 1.5 1.5 150 32 24 32 39 32.5 39 2 1.5 165 52 40 52 2.5 2 180 34 29 37.00 46 39 049 63 48 63 3 2.5 215 47 39 051.5 51 35 56.5 73 60 077.5 4 3 100 20
21 105 145 24 25 25 20 25 1.5 1.5 160 35 26 35 43 34 43 2.5 2 175 56 44 56 2.5 2 190 36 30 39.00 50 43 053 68 52 68 3 2.5 225 49 41 053.5 53 36 58.0 77 63 081.5 4 3 105 21
22 110 150 24 25 25 20 25 1.5 1.5 170 38 29 38 47 37 47 2.5 2 180 56 43 56 2.5 2 200 38 32 41.00 53 46 056 3 2.5 240 50 42 054.5 57 38 63.0 80 65 084.5 4 3 110 22
24 120 165 27 29 29 23 29 1.5 1.5 180 38 29 38 48 38 48 2.5 2 200 62 48 62 2.5 2 215 40 34 43.50 58 50 061.5 3 2.5 260 55 46 059.5 62 42 68.0 86 69 090.5 4 3 120 24
26 130 180 30 32 32 25 32 2 1.5 200 45 34 45 55 43 55 2.5 2 230 40 34 43.75 64 54 067.75 4 3 280 58 49 063.75 66 44 72.0 93 78 098.75 5 4 130 26
28 140 190 30 32 32 25 32 2 1.5 210 45 34 45 56 44 56 2.5 2 250 42 36 45.75 68 58 071.75 4 3 300 62 53 067.75 70 47 77.0 102 85 107.75 5 4 140 28
30 150 210 36 38 38 30 38 2.5 2 225 48 36 48 59 46 59 3 2.5 270 45 38 49.00 73 60 077 4 3 320 65 55 072 75 50 82.0 108 90 114 5 4 150 30
32 160 220 36 38 38 30 38 2.5 2 240 51 38 51 3 2.5 290 48 40 52.00 80 67 084 4 3 340 68 58 075 79 87.0 114 95 121 5 4 160 32
34 170 230 36 38 38 30 38 2.5 2 260 57 43 57 3 2.5 310 52 43 57.00 86 71 091 5 4 360 72 62 080 84 92.0 120 100 127 5 4 170 34
36 180 250 42 45 45 34 45 2.5 2 280 64 48 64 3 2.5 320 52 43 57.00 86 71 091 5 4 380 75 64 083 88 97.0 126 106 134 5 4 180 36
38 190 260 42 45 45 34 45 2.5 2 290 64 48 64 3 2.5 340 55 46 60.00 92 75 097 5 4 400 78 65 086 92 101.0 132 109 140 6 5 190 38
40 200 280 48 51 51 39 51 3 2.5 310 70 53 70 3 2.5 360 58 48 64.00 98 82 104 5 4 420 80 67 089 97 107.0 138 115 146 6 5 200 40
44 220 300 48 51 51 39 51 3 2.5 340 76 57 76 4 3 400 65 54 72.00 108 90 114 5 4 460 88 73 097 106 117.0 145 122 154 6 5 220 44
48 240 320 48 51 51 39 51 3 2.5 360 76 57 76 4 3 440 72 60 79.00 120 100 127 5 4 500 95 80 105 114 125.0 155 132 165 6 5 240 48
52 260 360 63.5 48 63.5 3 2.5 400 87 65 87 5 4 480 80 67 89.00 130 106 137 6 5 540 102 85 113 123 135.0 165 136 176 6 6 260 52
56 280 380 63.5 48 63.5 3 2.5 420 87 65 87 5 4 500 80 67 89.00 130 106 137 6 5 580 108 90 119 132 145.0 175 145 187 6 6 280 56
60 300 420 76 57 76 4 3 460 100 74 100 5 4 540 85 71 96.00 140 115 149 6 5 300 60
64 320 440 76 57 76 4 3 480 100 74 100 5 4 580 92 75 104.00 150 125 159 6 5 320 64
68 340 460 76 57 76 4 3 340 68
72 360 480 76 57 76 4 3 360 72
Remarks 1. Other series not conforming to this table are also specified by ISO. Note (1) Regarding steep-slope bearing 303D, in DIN, the one corresponding to 303D of JIS is numbered 313. For bearings with
Remarks 2. In the Dimension Series of Diameter Series 9, Classification1is those specified by the old standard, Classification 2 bore diameters larger than 100 mm, those of dimension series 13 are numbered 313.
is those specified by the ISO.
Remarks 2. Dimension Series not classified conform to dimensions (D, B, C, T) specified by ISO.
Remarks 3. The chamfer dimensions listed are the minimum permissible dimensions specified by ISO. They do not apply to
chamfers on the front face.
A 44 A 45
A024-057E.indd 44-45 11/20/13 4:50:29 PM

Table 7. 3 Boundary Dimensions of Thrust Bearings (Flat Seats) 1

Units: mm
Thrust Ball Brgs. 511 512 522 513 523 514 524 Thrust Ball
Brgs.
Spherical Thrust 292 293 294 Spherical Thrust
Roller Brgs. Roller Brgs.
Diameter Series 0 Diameter Series 1 Diameter Series 2 Diameter Series 3 Diameter Series 4 Diameter Series 5
Dimension
Dimension Series Dimension Series Dimension Series Dimension Series Dimension Series
Bore Number
Bore Number
Series
70 90 10 71 91 11 72 92 12 22 22 73 93 13 23 23 74 94 14 24 24 95
d
D r (min.) D r (min.) D r (min.) r1 (min.) D r (min.) r1 (min.) D r (min.) r1 (min.) D r (min.) d
Central Washer Central Washer Central Washer
T T T T T T
d2 B d2 B d2 B
4 4 12 4 6 0.3 16 6 8 0.3 20 7 11 0.6 4 4

6 6 16 5 7 0.3 20 6 9 0.3 24 8 12 0.6 6 6
8 8 18 5 7 0.3 22 6 9 0.3 26 8 12 0.6 8 8
00 10 20 5 7 0.3 24 6 9 0.3 26 7 11 0.6 30 9 14 0.6 10 00

01 12 22 5 7 0.3 26 6 9 0.3 28 7 11 0.6 32 9 14 0.6 12 01
02 15 26 5 7 0.3 28 6 9 0.3 32 8 12 22 10 5 0.6 0.3 37 10 15 0.6 15 02
03 17 28 5 7 0.3 30 6 9 0.3 35 8 12 0.6 40 10 16 0.6 52 21 1 17 03

04 20 32 6 8 0.3 35 7 10 0.3 40 9 14 26 15 6 0.6 0.3 47 12 18 1 60 24 1 20 04
05 25 37 6 8 0.3 42 8 11 0.6 47 10 15 28 20 7 0.6 0.3 52 12 18 34 20 8 1 0.3 60 16 21 24 45 15 11 1 0.6 73 29 1.1 25 05
06 30 42 6 8 0.3 47 8 11 0.6 52 10 16 29 25 7 0.6 0.3 60 14 21 38 25 9 1 0.3 70 18 24 28 52 20 12 1 0.6 85 34 1.1 30 06

07 35 47 6 8 0.3 52 8 12 0.6 62 12 18 34 30 8 1 0.3 68 15 24 44 30 10 1 0.3 80 20 27 32 59 25 14 1.1 0.6 100 39 1.1 35 07
08 40 52 6 9 0.3 60 9 13 0.6 68 13 19 36 30 9 1 0.6 78 17 22 26 49 30 12 1 0.6 90 23 30 36 65 30 15 1.1 0.6 110 42 1.5 40 08
09 45 60 7 10 0.3 65 9 14 0.6 73 13 20 37 35 9 1 0.6 85 18 24 28 52 35 12 1 0.6 100 25 34 39 72 35 17 1.1 0.6 120 45 2 45 09

10 50 65 7 10 0.3 70 9 14 0.6 78 13 22 39 40 9 1 0.6 95 20 27 31 58 40 14 1.1 0.6 110 27 36 43 78 40 18 1.5 0.6 135 51 2 50 10
11 55 70 7 10 0.3 78 10 16 0.6 90 16 21 25 45 45 10 1 0.6 105 23 30 35 64 45 15 1.1 0.6 120 29 39 48 87 45 20 1.5 0.6 150 58 2.1 55 11
12 60 75 7 10 0.3 85 11 17 1 95 16 21 26 46 50 10 1 0.6 110 23 30 35 64 50 15 1.1 0.6 130 32 42 51 93 50 21 1.5 0.6 160 60 2.1 60 12
13 65 80 7 10 0.3 90 11 18 1 100 16 21 27 47 55 10 1 0.6 115 23 30 36 65 55 15 1.1 0.6 140 34 45 56 101 50 23 2 1 170 63 2.1 65 13
14 70 85 7 10 0.3 95 11 18 1 105 16 21 27 47 55 10 1 1 125 25 34 40 72 55 16 1.1 1 150 36 48 60 107 55 24 2 1 180 67 3 70 14
15 75 90 7 10 0.3 100 11 19 1 110 16 21 27 47 60 10 1 1 135 27 36 44 79 60 18 1.5 1 160 38 51 65 115 60 26 2 1 190 69 3 75 15

16 80 95 7 10 0.3 105 11 19 1 115 16 21 28 48 65 10 1 1 140 27 36 44 79 65 18 1.5 1 170 41 54 68 120 65 27 2.1 1 200 73 3 80 16
17 85 100 7 10 0.3 110 11 19 1 125 18 24 31 55 70 12 1 1 150 29 39 49 87 70 19 1.5 1 180 42 58 72 128 65 29 2.1 1.1 215 78 4 85 17
18 90 105 7 10 0.3 120 14 22 1 135 20 27 35 62 75 14 1.1 1 155 29 39 50 88 75 19 1.5 1 190 45 60 77 135 70 30 2.1 1.1 225 82 4 90 18
20 100 120 9 14 0.6 135 16 21 25 1 150 23 30 38 67 85 15 1.1 1 170 32 42 55 97 85 21 1.5 1 210 50 67 85 150 80 33 3 1.1 250 90 4 100 20
22 110 130 9 14 0.6 145 16 21 25 1 160 23 30 38 67 95 15 1.1 1 190 36 48 63 110 95 24 2 1 230 54 73 95 166 90 37 3 1.1 270 95 5 110 22
24 120 140 9 14 0.6 155 16 21 25 1 170 23 30 39 68 100 15 1.1 1.1 210 41 54 70 123 100 27 2.1 1.1 250 58 78 102 177 95 40 4 1.5 300 109 5 120 24
26 130 150 9 14 0.6 170 18 24 30 1 190 27 36 45 80 110 18 1.5 1.1 225 42 58 75 130 110 30 2.1 1.1 270 63 85 110 192 100 42 4 2 320 115 5 130 26
28 140 160 9 14 0.6 180 18 24 31 1 200 27 36 46 81 120 18 1.5 1.1 240 45 60 80 140 120 31 2.1 1.1 280 63 85 112 196 110 44 4 2 340 122 5 140 28
30 150 170 9 14 0.6 190 18 24 31 1 215 29 39 50 89 130 20 1.5 1.1 250 45 60 80 140 130 31 2.1 1.1 300 67 90 120 209 120 46 4 2 360 125 6 150 30
32 160 180 9 14 0.6 200 18 24 31 1 225 29 39 51 90 140 20 1.5 1.1 270 50 67 87 153 140 33 3 1.1 320 73 95 130 226 130 50 5 2 380 132 6 160 32
34 170 190 9 14 0.6 215 20 27 34 1.1 240 32 42 55 97 150 21 1.5 1.1 280 50 67 87 153 150 33 3 1.1 340 78 103 135 236 135 50 5 2.1 400 140 6 170 34
36 180 200 9 14 0.6 225 20 27 34 1.1 250 32 42 56 98 150 21 1.5 2 300 54 73 95 165 150 37 3 2 360 82 109 140 245 140 52 5 3 420 145 6 180 36
38 190 215 11 17 1 240 23 30 37 1.1 270 36 48 62 109 160 24 2 2 320 58 78 105 183 160 40 4 2 380 85 115 150 5 440 150 6 190 38
40 200 225 11 17 1 250 23 30 37 1.1 280 36 48 62 109 170 24 2 2 340 63 85 110 192 170 42 4 2 400 90 122 155 5 460 155 7.5 200 40
44 220 250 14 22 1 270 23 30 37 1.1 300 36 48 63 110 190 24 2 2 360 63 85 112 4 420 90 122 160 6 500 170 7.5 220 44
48 240 270 14 22 1 300 27 36 45 1.5 340 45 60 78 2.1 380 63 85 112 4 440 90 122 160 6 540 180 7.5 240 48
52 260 290 14 22 1 320 27 36 45 1.5 360 45 60 79 2.1 420 73 95 130 5 480 100 132 175 6 580 190 9.5 260 52
56 280 310 14 22 1 350 32 42 53 1.5 380 45 60 80 2.1 440 73 95 130 5 520 109 145 190 6 620 206 9.5 280 56
60 300 340 18 24 30 1 380 36 48 62 2 420 54 73 95 3 480 82 109 140 5 540 109 145 190 6 670 224 9.5 300 60
64 320 360 18 24 30 1 400 36 48 63 2 440 54 73 95 3 500 82 109 140 5 580 118 155 205 7.5 710 236 9.5 320 64
Remarks 1. Dimension Series 22, 23, and 24 are double direction bearings.
Remarks 2. The maximum permissible outside diameter of shaft and central washers and minimum permissible bore diameter of
housing washers are omitted here. (Refer to the bearing tables for Thrust Bearings).
A 46 A 47
A024-057E.indd 46-47 11/20/13 4:50:31 PM

Table 7. 3 Boundary Dimensions of Thrust Bearings (Flat Seats) 2

Units: mm
Thrust Ball Brgs. 511 512 522 513 523 514 524 Thrust Ball
Brgs.
Spherical Thrust 292 293 294 Spherical Thrust
Roller Brgs. Roller Brgs.
Diameter Series 0 Diameter Series 1 Diameter Series 2 Diameter Series 3 Diameter Series 4 Diameter Series 5
Dimension
Dimension Series Dimension Series Dimension Series Dimension Series Dimension Series
Bore Number
Bore Number
Series
70 90 10 71 91 11 72 92 12 22 22 73 93 13 23 23 74 94 14 24 24 95
d d
D r (min.) D r (min.) D r (min.) r1 (min.) D r (min.) r1 (min.) D r (min.) r1 (min.) D r (min.)
Central Washer Central Washer Central Washer
T T T T T T
d2 B d2 B d2 B
68 340 380 18 24 30 1 420 36 48 64 2 460 54 073 96 3 540 90 122 160 5 620 125 170 220 7.5 750 243 12 340 68
72 360 400 18 24 30 1 440 36 48 65 2 500 63 085 110 4 560 90 122 160 5 640 125 170 220 7.5 780 250 12 360 72
76 380 420 18 24 30 1 460 36 48 65 2 520 63 085 112 4 600 100 132 175 6 670 132 175 224 7.5 820 265 12 380 76
80 400 440 18 24 30 1 480 36 48 65 2 540 63 085 112 4 620 100 132 175 6 710 140 185 243 7.5 850 272 12 400 80
84 420 460 18 24 30 1 500 36 48 65 2 580 73 095 130 5 650 103 140 180 6 730 140 185 243 7.5 900 290 15 420 84
88 440 480 18 24 30 1 540 45 60 80 2.1 600 73 095 130 5 680 109 145 190 6 780 155 206 265 9.5 950 308 15 440 88
92 460 500 18 24 30 1 560 45 60 80 2.1 620 73 095 130 5 710 112 150 195 6 800 155 206 265 9.5 980 315 15 460 92
96 480 520 18 24 30 1 580 45 60 80 2.1 650 78 103 135 5 730 112 150 195 6 850 165 224 290 9.5 1000 315 15 480 96
/500 500 540 18 24 30 1 600 45 60 80 2.1 670 78 103 135 5 750 112 150 195 6 870 165 224 290 9.5 1060 335 15 500 /500
/530 530 580 23 30 38 1.1 640 50 67 85 3 710 82 109 140 5 800 122 160 212 7.5 920 175 236 308 9.5 1090 335 15 530 /530
/560 560 610 23 30 38 1.1 670 50 67 85 3 750 85 115 150 5 850 132 175 224 7.5 980 190 250 335 12 1150 355 15 560 /560
/600 600 650 23 30 38 1.1 710 50 67 85 3 800 90 122 160 5 900 136 180 236 7.5 1030 195 258 335 12 1220 375 15 600 /600
/630 630 680 23 30 38 1.1 750 54 73 95 3 850 100 132 175 6 950 145 190 250 9.5 1090 206 280 365 12 1280 388 15 630 /630
/670 670 730 27 36 45 1.5 800 58 78 105 4 900 103 140 180 6 1000 150 200 258 9.5 1150 218 290 375 15 1320 388 15 670 /670
/710 710 780 32 42 53 1.5 850 63 85 112 4 950 109 145 190 6 1060 160 212 272 9.5 1220 230 308 400 15 1400 412 15 710 /710
/750 750 820 32 42 53 1.5 900 67 90 120 4 1000 112 150 195 6 1120 165 224 290 9.5 1280 236 315 412 15 750 /750
/800 800 870 32 42 53 1.5 950 67 90 120 4 1060 118 155 205 7.5 1180 170 230 300 9.5 1360 250 335 438 15 800 /800
/850 850 920 32 42 53 1.5 1000 67 90 120 4 1120 122 160 212 7.5 1250 180 243 315 12 1440 354 15 850 /850
/900 900 980 36 48 63 2 1060 73 95 130 5 1180 125 170 220 7.5 1320 190 250 335 12 1520 372 15 900 /900
/950 950 1030 36 48 63 2 1120 78 103 135 5 1250 136 180 236 7.5 1400 200 272 355 12 1600 390 15 950 /950
/1000 1000 1090 41 54 70 2.1 1180 82 109 140 5 1320 145 190 250 9.5 1460 276 12 1670 402 15 1000 /1000
/1060 1060 1150 41 54 70 2.1 1250 85 115 150 5 1400 155 206 265 9.5 1540 288 15 1770 426 15 1060 /1060
/1120 1120 1220 45 60 80 2.1 1320 90 122 160 5 1460 206 9.5 1630 306 15 1860 444 15 1120 /1120
/1180 1180 1280 45 60 80 2.1 1400 100 132 175 6 1520 206 9.5 1710 318 15 1950 462 19 1180 /1180
/1250 1250 1360 50 67 85 3 1460 175 6 1610 216 9.5 1800 330 19 2050 480 19 1250 /1250
/1320 1320 1440 95 3 1540 175 6 1700 228 9.5 1900 348 19 2160 505 19 1320 /1320
/1400 1400 1520 95 3 1630 180 6 1790 234 12 2000 360 19 2280 530 19 1400 /1400
/1500 1500 1630 105 4 1750 195 6 1920 252 12 2140 384 19 1500 /1500
/1600 1600 1730 105 4 1850 195 6 2040 264 15 2270 402 19 1600 /1600
/1700 1700 1840 112 4 1970 212 7.5 2160 276 15 1700 /1700
/1800 1800 1950 120 4 2080 220 7.5 2280 288 15 1800 /1800
/1900 1900 2060 130 5 2180 220 7.5 1900 /1900
/2000 2000 2160 130 5 2300 236 7.5 2000 /2000
/2120 2120 2300 140 5 2430 243 7.5 2120 /2120

/2240 2240 2430 150 5 2570 258 9.5 2240 /2240
/2360 2360 2550 150 5 2700 265 9.5 2360 /2360
/2500 2500 2700 160 5 2850 272 9.5 2500 /2500
Remarks 1. Dimension Series 22, 23, and 24 are double direction bearings.
Remarks 2. The maximum permissible outside diameter of shaft and central washers and minimum permissible bore diameter of
housing washers are omitted here. (Refer to the bearings tables for Thrust Bearings).
A 48 A 49
A024-057E.indd 48-49 11/20/13 4:50:33 PM

Table 7. 4 Dimensions of Snap Ring Grooves and Locating Snap Rings (1)
Bearings of Dimension Series 18 and 19
f
a b Side Cover Housing
r0 g (Geometry of locating snap ring fitted in groove)
rN
rN e
jD 2
jD 1 jD x
Units: mm
Applicable Bearings Snap Ring Groove Locating Snap Ring Side Cover
Snap Ring Groove Position Geometry of snap ring
Snap Ring Groove Snap Ring Groove Radius of Cross Sectional Thickness fitted in groove Stepped Bore
d a Bottom Locating Snap (Reference) Diameter
Diameter Width Height (Reference)
Bearing Dimension Series Corners Ring Number Slit Snap Ring
D Width Outside
Dimension Series
D1
18 19
b r0 e f DX
g Diameter D2
18 19 max. min. max. min. max. min. max. min. max. max. min. max. min. approx. max. min.
10 22 20.8 20.5 1.05 0.9 1.05 0.8 0.2 NR 1022 2.0 1.85 0.7 0.6 2 24.8 25.5
12 24 22.8 22.5 1.05 0.9 1.05 0.8 0.2 NR 1024 2.0 1.85 0.7 0.6 2 26.8 27.5
15 28 26.7 26.4 1.3 1.15 1.2 0.95 0.25 NR 1028 2.05 1.9 0.85 0.75 3 30.8 31.5
17 30 28.7 28.4 1.3 1.15 1.2 0.95 0.25 NR 1030 2.05 1.9 0.85 0.75 3 32.8 33.5
20 32 30.7 30.4 1.3 1.15 1.2 0.95 0.25 NR 1032 2.05 1.9 0.85 0.75 3 34.8 35.5
22 34 32.7 32.4 1.3 1.15 1.2 0.95 0.25 NR 1034 2.05 1.9 0.85 0.75 3 36.8 37.5
25 20 37 35.7 35.4 1.3 1.15 1.7 1.55 1.2 0.95 0.25 NR 1037 2.05 1.9 0.85 0.75 3 39.8 40.5
22 39 37.7 37.4 1.7 1.55 1.2 0.95 0.25 NR 1039 2.05 1.9 0.85 0.75 3 41.8 42.5
28 40 38.7 38.4 1.3 1.15 1.2 0.95 0.25 NR 1040 2.05 1.9 0.85 0.75 3 42.8 43.5
30 25 42 40.7 40.4 1.3 1.15 1.7 1.55 1.2 0.95 0.25 NR 1042 2.05 1.9 0.85 0.75 3 44.8 45.5
32 44 42.7 42.4 1.3 1.15 1.2 0.95 0.25 NR 1044 2.05 1.9 0.85 0.75 4 46.8 47.5
28 45 43.7 43.4 1.7 1.55 1.2 0.95 0.25 NR 1045 2.05 1.9 0.85 0.75 4 47.8 48.5
35 30 47 45.7 45.4 1.3 1.15 1.7 1.55 1.2 0.95 0.25 NR 1047 2.05 1.9 0.85 0.75 4 49.8 50.5
40 32 52 50.7 50.4 1.3 1.15 1.7 1.55 1.2 0.95 0.25 NR 1052 2.05 1.9 0.85 0.75 4 54.8 55.5
35 55 53.7 53.4 1.7 1.55 1.2 0.95 0.25 NR 1055 2.05 1.9 0.85 0.75 4 57.8 58.5
45 58 56.7 56.4 1.3 1.15 1.2 0.95 0.25 NR 1058 2.05 1.9 0.85 0.75 4 60.8 61.5
40 62 60.7 60.3 1.7 1.55 1.2 0.95 0.25 NR 1062 2.05 1.9 0.85 0.75 4 64.8 65.5
50 65 63.7 63.3 1.3 1.15 1.2 0.95 0.25 NR 1065 2.05 1.9 0.85 0.75 4 67.8 68.5
45 68 66.7 66.3 1.7 1.55 1.2 0.95 0.25 NR 1068 2.05 1.9 0.85 0.75 5 70.8 72
55 50 72 70.7 70.3 1.7 1.55 1.7 1.55 1.2 0.95 0.25 NR 1072 2.05 1.9 0.85 0.75 5 74.8 76
60 78 76.2 75.8 1.7 1.55 1.6 1.3 0.4 NR 1078 3.25 3.1 1.12 1.02 5 82.7 84
55 80 77.9 77.5 2.1 1.9 1.6 1.3 0.4 NR 1080 3.25 3.1 1.12 1.02 5 84.4 86
65 60 85 82.9 82.5 1.7 1.55 2.1 1.9 1.6 1.3 0.4 NR 1085 3.25 3.1 1.12 1.02 5 89.4 91
70 65 90 87.9 87.5 1.7 1.55 2.1 1.9 1.6 1.3 0.4 NR 1090 3.25 3.1 1.12 1.02 5 94.4 96
75 95 92.9 92.5 1.7 1.55 1.6 1.3 0.4 NR 1095 3.25 3.1 1.12 1.02 5 99.4 101
80 70 100 97.9 97.5 1.7 1.55 2.5 2.3 1.6 1.3 0.4 NR 1100 3.25 3.1 1.12 1.02 5 104.4 106
75 105 102.6 102.1 2.5 2.3 1.6 1.3 0.4 NR 1105 4.04 3.89 1.12 1.02 5 110.7 112
85 80 110 107.6 107.1 2.1 1.9 2.5 2.3 1.6 1.3 0.4 NR 1110 4.04 3.89 1.12 1.02 5 115.7 117
90 115 112.6 112.1 2.1 1.9 1.6 1.3 0.4 NR 1115 4.04 3.89 1.12 1.02 5 120.7 122
95 85 120 117.6 117.1 2.1 1.9 3.3 3.1 1.6 1.3 0.4 NR 1120 4.04 3.89 1.12 1.02 7 125.7 127
100 90 125 122.6 122.1 2.1 1.9 3.3 3.1 1.6 1.3 0.4 NR 1125 4.04 3.89 1.12 1.02 7 130.7 132
105 95 130 127.6 127.1 2.1 1.9 3.3 3.1 1.6 1.3 0.4 NR 1130 4.04 3.89 1.12 1.02 7 135.7 137
110 100 140 137.6 137.1 2.5 2.3 3.3 3.1 2.2 1.9 0.6 NR 1140 4.04 3.89 1.7 1.6 7 145.7 147
105 145 142.6 142.1 3.3 3.1 2.2 1.9 0.6 NR 1145 4.04 3.89 1.7 1.6 7 150.7 152
120 110 150 147.6 147.1 2.5 2.3 3.3 3.1 2.2 1.9 0.6 NR 1150 4.04 3.89 1.7 1.6 7 155.7 157
130 120 165 161.8 161.3 3.3 3.1 3.7 3.5 2.2 1.9 0.6 NR 1165 4.85 4.7 1.7 1.6 7 171.5 173
140 175 171.8 171.3 3.3 3.1 2.2 1.9 0.6 NR 1175 4.85 4.7 1.7 1.6 10 181.5 183
130 180 176.8 176.3 3.7 3.5 2.2 1.9 0.6 NR 1180 4.85 4.7 1.7 1.6 10 186.5 188
150 140 190 186.8 186.3 3.3 3.1 3.7 3.5 2.2 1.9 0.6 NR 1190 4.85 4.7 1.7 1.6 10 196.5 198
160 200 196.8 196.3 3.3 3.1 2.2 1.9 0.6 NR 1200 4.85 4.7 1.7 1.6 10 206.5 208
Remarks The minimum permissible chamfer dimensions rN on the snap-ring-groove side of the outer rings are as follows:
Dimension series 18 : For outside diameters of 78mm and less, use 0.3mm chamfer.
For all others exceeding 78mm, use 0.5mm chamfer.
Dimension series 19 : For outside diameters of 24mm and less, use 0.2mm chamfer.
For 47mm and less, use 0.3mm chamfer.
A 50 For all others exceeding 47mm, use 0.5mm chamfer (However, for an outside diameter of A 51
68 mm, use a 0.3 mm chamfer, which is not compliant with ISO 15).
A024-057E.indd 50-51 11/20/13 4:50:35 PM

Table 7. 4 Dimensions of Snap Ring Grooves and Locating Snap Rings (2)
Bearing of Diameter Series 0, 2, 3, and 4 f
Side Cover Housing
g (Geometry of locating snap ring fitted in groove)
a b
r0
rN e
rN
jD 2
jD x
jD 1
Units: mm
Applicable Bearings Snap Ring Groove Locating Snap Ring Side Cover
Snap Ring Groove Position Geometry of snap ring
Snap Ring Groove Snap Ring Groove Radius Cross Sectional Thickness fitted in groove Stepped Bore
d a of Locating Snap (Reference) Diameter
Diameter Width Bottom Height (Reference)
Bearing Diameter Series Ring Number Slit Snap Ring
Corners Width Outside
Diameter Series
D D1
0 2, 3, 4
b r0 e f DX
g Diameter D2
0 2 3 4 max. min. max. min. max. min. max. min. max. max. min. max. min. approx. max. min.
10 26 24.5 24.25 1.35 1.19 1.17 0.87 0.2 NR 026 (1) 2.06 1.91 0.84 0.74 03 28.7 29.4
12 28 26.5 26.25 1.35 1.19 1.17 0.87 0.2 NR 028 (1) 2.06 1.91 0.84 0.74 03 30.7 31.4
10 9 8 30 28.17 27.91 2.06 1.9 1.65 1.35 0.4 NR 030 3.25 3.1 1.12 1.02 03 34.7 35.5
15 12 9 32 30.15 29.9 2.06 1.9 2.06 1.9 1.65 1.35 0.4 NR 032 3.25 3.1 1.12 1.02 03 36.7 37.5
17 15 10 35 33.17 32.92 2.06 1.9 2.06 1.9 1.65 1.35 0.4 NR 035 3.25 3.1 1.12 1.02 03 39.7 40.5
12 10 37 34.77 34.52 2.06 1.9 1.65 1.35 0.4 NR 037 3.25 3.1 1.12 1.02 03 41.3 42
17 40 38.1 37.85 2.06 1.9 1.65 1.35 0.4 NR 040 3.25 3.1 1.12 1.02 03 44.6 45.5
20 15 12 42 39.75 39.5 2.06 1.9 2.06 1.9 1.65 1.35 0.4 NR 042 3.25 3.1 1.12 1.02 03 46.3 47
22 44 41.75 41.5 2.06 1.9 1.65 1.35 0.4 NR 044 3.25 3.1 1.12 1.02 03 48.3 49
25 20 17 47 44.6 44.35 2.06 1.9 2.46 2.31 1.65 1.35 0.4 NR 047 4.04 3.89 1.12 1.02 04 52.7 53.5
22 50 47.6 47.35 2.46 2.31 1.65 1.35 0.4 NR 050 4.04 3.89 1.12 1.02 04 55.7 56.5
28 25 20 15 52 49.73 49.48 2.06 1.9 2.46 2.31 1.65 1.35 0.4 NR 052 4.04 3.89 1.12 1.02 04 57.9 58.5
30 55 52.6 52.35 2.08 1.88 1.65 1.35 0.4 NR 055 4.04 3.89 1.12 1.02 04 60.7 61.5
22 56 53.6 53.35 2.46 2.31 1.65 1.35 0.4 NR 056 4.04 3.89 1.12 1.02 04 61.7 62.5
32 28 58 55.6 55.35 2.08 1.88 2.46 2.31 1.65 1.35 0.4 NR 058 4.04 3.89 1.12 1.02 04 63.7 64.5
35 30 25 17 62 59.61 59.11 2.08 1.88 3.28 3.07 2.2 1.9 0.6 NR 062 4.04 3.89 1.7 1.6 04 67.7 68.5
32 65 62.6 62.1 3.28 3.07 2.2 1.9 0.6 NR 065 4.04 3.89 1.7 1.6 04 70.7 71.5
40 28 68 64.82 64.31 2.49 2.29 3.28 3.07 2.2 1.9 0.6 NR 068 4.85 4.7 1.7 1.6 05 74.6 76
35 30 20 72 68.81 68.3 3.28 3.07 2.2 1.9 0.6 NR 072 4.85 4.7 1.7 1.6 05 78.6 80
45 32 75 71.83 71.32 2.49 2.29 3.28 3.07 2.2 1.9 0.6 NR 075 4.85 4.7 1.7 1.6 05 81.6 83
50 40 35 25 80 76.81 76.3 2.49 2.29 3.28 3.07 2.2 1.9 0.6 NR 080 4.85 4.7 1.7 1.6 05 86.6 88
45 85 81.81 81.31 3.28 3.07 2.2 1.9 0.6 NR 085 4.85 4.7 1.7 1.6 05 91.6 93
55 50 40 30 90 86.79 86.28 2.87 2.67 3.28 3.07 3 2.7 0.6 NR 090 4.85 4.7 2.46 2.36 05 96.5 98
60 95 91.82 91.31 2.87 2.67 3 2.7 0.6 NR 095 4.85 4.7 2.46 2.36 05 101.6 103
65 55 45 35 100 96.8 96.29 2.87 2.67 3.28 3.07 3 2.7 0.6 NR 100 4.85 4.7 2.46 2.36 05 106.5 108
70 60 50 40 110 106.81 106.3 2.87 2.67 3.28 3.07 3 2.7 0.6 NR 110 4.85 4.7 2.46 2.36 05 116.6 118
75 115 111.81 111.3 2.87 2.67 3 2.7 0.6 NR 115 4.85 4.7 2.46 2.36 05 121.6 123
65 55 45 120 115.21 114.71 4.06 3.86 3.4 3.1 0.6 NR 120 7.21 7.06 2.82 2.72 07 129.7 131.5
80 70 125 120.22 119.71 2.87 2.67 4.06 3.86 3.4 3.1 0.6 NR 125 7.21 7.06 2.82 2.72 07 134.7 136.5
85 75 60 50 130 125.22 124.71 2.87 2.67 4.06 3.86 3.4 3.1 0.6 NR 130 7.21 7.06 2.82 2.72 07 139.7 141.5
90 80 65 55 140 135.23 134.72 3.71 3.45 4.9 4.65 3.4 3.1 0.6 NR 140 7.21 7.06 2.82 2.72 07 149.7 152
95 145 140.23 139.73 3.71 3.45 3.4 3.1 0.6 NR 145 7.21 7.06 2.82 2.72 07 154.7 157
100 85 70 60 150 145.24 144.73 3.71 3.45 4.9 4.65 3.4 3.1 0.6 NR 150 7.21 7.06 2.82 2.72 07 159.7 162
105 90 75 65 160 155.22 154.71 3.71 3.45 4.9 4.65 3.4 3.1 0.6 NR 160 7.21 7.06 2.82 2.72 07 169.7 172
110 95 80 170 163.65 163.14 3.71 3.45 5.69 5.44 3.8 3.5 0.6 NR 170 9.6 9.45 3.1 3 10 182.9 185
120 100 85 70 180 173.66 173.15 3.71 3.45 5.69 5.44 3.8 3.5 0.6 NR 180 9.6 9.45 3.1 3 10 192.9 195
105 90 75 190 183.64 183.13 5.69 5.44 3.8 3.5 0.6 NR 190 9.6 9.45 3.1 3 10 202.9 205
130 110 95 80 200 193.65 193.14 5.69 5.44 5.69 5.44 3.8 3.5 0.6 NR 200 9.6 9.45 3.1 3 10 212.9 215
Note (1) The locating snap rings and snap ring grooves of these bearings are not specified by ISO.
Remarks 1. The dimensions of these snap ring grooves are not applicable to bearings of dimension series 00, 82, and 83.
2. The minimum permissible chamfer dimension rN on the snap-ring side of outer rings is 0.5mm. However, for
bearings of diameter series 0 having outside diameters 35mm and below, it is 0.3mm.
A 52 A 53
A024-057E.indd 52-53 11/20/13 4:50:36 PM

7.2 Formulation of Bearing Numbers (Example 4) NU 3 1 8 M CM Table 7. 5 Bearing Series Symbols

Bearing numbers are alphanumeric combinations Radial Clearance for Dimension Symbols Dimension Symbols
that indicate the bearing type, boundary dimensions, Electric-Motor Bearings CM
dimensional and running accuracies, internal clearance, Machined Brass Cage Bearing Bearing
Type Type Width
and other related specifications. They consist of Bearing Type Series Bearing Type Series Symbols Diameter
basic numbers and supplementary symbols. The Bearing Bore 90mm Symbols Width Diameter Symbols
Symbols Symbols or
boundary dimensions of commonly used bearings Diameter Series 3 Symbols Symbols Height Symbols
mostly conform to the organizational concept of ISO, Symbols
and the bearing numbers of these standard bearings NU Type Cylindrical
Roller Bearing 68 6 (1) 8 Double-Row
are specified by JIS B 1513 (Bearing Numbers for NNU49 NNU 4 9
Rolling Bearings). Due to a need for more detailed Single-Row 69 6 (1) 9 Cylindrical
(Example 5) NN 3 0 1 7 K CC1 P4 NN30U NNU 3 0
classification, NSK uses auxiliary symbols other than Deep Groove 60 6 (1) 0 Roller Bearings
those specified by JIS. Accuracy of ISO Class 4 Ball Bearings 62 6 (0) 2
Bearing numbers consist of a basic number and Radial Clearance in Non- 63 6 (0) 3
NA48 NA 4 8
supplementary symbols. The basic number indicates Interchangeable Cylindrical Needle Roller NA49 NA 4 9
the bearing series(type) and the width and diameter Roller Bearings CC1
79 7 (1) 9 Bearings NA59 NA 5 9
series as shown in Table 7.5. Basic numbers, Tapered Bore (Taper 1:12) Single-Row
70 7 (1) 0 NA69 NA 6 9
supplementary symbols, and the meanings of common Bearing Bore 85mm Angular Contact
numbers and symbols are listed in Table 7.6 (Pages 72 7 (0) 2
Diameter Series 0 Ball Bearings
A56 and A57). The contact angle symbols and other 73 7 (0) 3 329 3 2 9
supplementary designations are shown in successive Width Series 3 320 3 2 0
columns from left to right in Table 7.6. For reference, 12 1 (0) 2
NN Type Cylindrical 330 3 3 0
some examples of bearing designations are shown Roller Bearing Self-Aligning 13 1 (0) 3
here: 331 3 3 1
Ball Bearings 22 (1) 2 2
(Example 6) HR 3 0 2 0 7 J Tapered Roller 302 3 0 2
23 (1) 2 3
Small Diameter of Cup Bearings 322 3 2 2
Raceway and Contact Angle NU10 NU 1 0
Conform to ISO NU20 NU (0) 2
332 3 3 2
(Example 1) 6 3 0 8 ZZ C3
Bearing Bore 35mm NU22 NU 2 2
Radial Clearance C3 Diameter Series 2
303 3 0 3
(Internal Clearance Symbol) NU30 NU (0) 3 323 3 2 3
Shields on Both Sides Width Series 0 NU23 NU 2 3
(Shield Symbol) Tapered Roller Bearing NU40 NU (0) 4 230 2 3 0
Bearing Bore 40mm
(Bore Number) High Capacity Bearing NJ20 NJ (0) 2
231 2 3 1
Spherical 222 2 2 2
}
Diameter Series 3 Bearing NJ22 NJ 2 2
(Example 7) 2 4 0 /1000 M K30 E4 C3 Roller
Single-Row Deep Series NJ30 NJ (0) 3 232 2 3 2
Groove Ball Bearing Symbol Bearings
Radial Clearance C3 NJ23 NJ 2 3 213 (1) 2 0 3
(Example 2) 7 2 2 0 A DB C3 Outer Ring with Oil Groove NJ40 NJ (0) 4
Single-Row 223 2 2 3
and Oil Holes
Axial Clearance C3 Cylindrical (0)
Tapered Bore (Taper 1:30) NUP20 NUP 2
Back-to-Back Arrangement Roller NUP22 NUP 2 2 511 5 1 1
Machined Brass Cage Bearings NUP30 NUP (0) 3 512 5 1 2
Contact Angle 30 o
Bearing Bore 1000mm NUP23 NUP 2 3 Thrust Ball

513 5 1 3
Bearing Bore 100mm
Diameter Series 0 514 5 1 4
Diameter Series 2 NUP40 NUP (0) 4 Bearings with
Width Series 4 Flat Seats 522 5 2 2
Single-Row Angular Contact Ball N10 N 1 0
Bearing Spherical Roller Bearing N20 N (0) 2 523 5 2 3
(Example 3) 1 2 0 6 K +H206X N30 N (0) 3 524 5 2 4
Adapter with 25mm Bore (Example 8) 5 1 2 1 5 N40 N (0) 4

Spherical 292 2 9 2
Tapered Bore (Taper 1:12) Bearing Bore 75mm NF2 NF (0) 2
Thrust Roller 293 2 9 3
Bearing Bore 30mm Diameter Series 2 NF3 NF (0) 3
Bearings 294 2 9 4
Diameter Series 2 NF4 NF (0) 4
Height Series 1
Self-Aligning Ball Bearing Note (1) Bearing Series Symbol 213 should logically be 203, but customarily it is numbered 213.
Thrust Ball Bearing Remarks Numbers in ( ) in the column of width symbols are usually omitted from the bearing number.
A 54 A 55
A024-057E.indd 54-55 11/20/13 4:50:37 PM

Table 7. 6 Formulation of Bearing Numbers
Basic Numbers Auxiliary Symbols
External Features Symbol Special

Bearing Series Contact Angle Arrangement Internal Clearance Symbol Tolerance Class Spacer or Sleeve
Bore Number Internal Design Symbol Material Symbol Cage Symbol Symbol Preload Symbol Symbol Specification Grease Symbol
Symbols (1) Symbol Seals, Shields Symbol for Design Symbol Symbol
Symbol of Rings
Symbol Meaning Symbol Meaning Symbol Meaning Symbol Meaning Symbol Meaning Symbol Meaning Symbol Meaning Symbol Meaning Symbol Meaning Symbol Meaning (radial clearance) Symbol Meaning Symbol Meaning Symbol Meaning Symbol Meaning
68
69
Single-
Row Deep
1 Bearing 1mm
Bore
(
Angular
Contact Ball ) A Internal Design
Differs from
g Case-Hardened
Steel Used in
M Machined
Brass Cage
Z
ZS } Shield
on One
K Tapered
Bore of
DB Back-to-Back
Arrangement
C1 Clearance Less
than C2
Omitted ISO Normal
(
Bearings
treated for
)
+K Bearings
with Outer
AS2 SHELL
ALVANIA
For All Radial Brgs.

Groove Ball 2 2 Bearings Standard One Rings, Rolling Side Inner Ring C2 Clearance Less Ring GREASE S2
60 Bearings A Standard Elements than CN Dimensional Spacers
Only (Taper 1:12)
3 3 Contact Angle J Smaller Diameter P6 ISO Class 6 Stabilization ENS ENS GREASE
: Omitted CN Clearance
of 30 of Outer Ring DF Face-to- +L Bearings
70 Single-Row Raceway, Contact Face Clearance Greater
Angular ZZ Shields C3 X26 Working with Inner
72
73
Contact Ball
Bearings 9 9
A5 Standard
Contact Angle
Angle, and Outer
Ring Width of W Pressed ZZS } on Both
Sides
K30 Tapered
Arrangement
C4
than CN
Clearance Greater P6X ISO Class 6X Temperature
Lower than
Ring
Spacers NS7 NS HI-LUBE
Tapered Roller Stainless Steel Steel Cage Bore of than C3
of 25 Bearings Conform h Inner Ring 150 C
: 00 100 Used in Rings, Clearance Greater
to ISO 355 Rolling Elements (Taper 1:30) DT Tandem C5 +KL Bearings
12 Self- Arrangement than C4 with Both
01 120 P5 ISO Class 5 X28 Working PS2 MULTEMP PS
13 Aligning Ball B Standard Temperature Inner and
Bearings Contact Angle DU Contact Clearance Less No. 2
02 150 CC1 Lower than Outer Ring
22 of 40 Rubber Seal than CC2
For Non-Interchangeable
Spacers
Cylindrical Roller Brgs.

on One Side 200 C
: 03 170 E Notch or Clearance Less
T Synthetic Only CC2 than CC P4 ISO Class 4
Resin Cage Lubricating
NU10 Cylindrical
Groove in X29 Working H Adapter
NJ 2 Roller
Bearings /22 220
C Standard
Contact Angle
(For High Capacity
Bearings ) Ring CC Normal Clearance Temperature
Lower than
Designation
N 3 of 15 DDU Contact Clearance Greater P2 ISO Class 2 250 C
/28 280 CC3 than CC
NN 30 Rubber AH Withdrawal
Seals on Clearance Greater Sleeve
: /32 320 C V Without Both Sides CC4 than CC3
( )
Cage E4 Lubricating ABMA( )7 Designation
NA48 Needle Groove in Clearance Greater Tapered
CC5
( )
Roller CA Outside than CC4 Spherical HJ Thrust
NA49
NA69
Bearings 04(3)
05
200
250 (Tapered
Roller
Bearings
) CD
Spherical Roller
Bearings
V Non-
Contact
Surface and
Holes in MC1
Clearance Less than
MC2
roller bearing
Roller
Bearings
Collar
Designation
and Miniature Ball Brgs.

: Rubber Seal Outer Ring Omitted Class 4
Omitted Contact Angle on One Side Clearance Less than S11 Dimensional
320 Tapered 06 300 Less than 17 MC2
For Extra-Small
EA Only MC3 Stabilizing
322 Roller N Snap Ring Treatment
Bearings MC3 Normal Clearance
323 ( 2) Groove in PN2 Class 2 Working
VV Non- Outer Ring Clearance Greater Temperature
: C Contact Angle MC4 Lower than
88 4400 about 20 E Cylindrical Roller Contact than MC3
Rubber 200C
230 Spherical Bearings Clearance Greater
92 4600 Seals on MC5 PN3 Class 3
222 Roller Both Sides NR Snap Ring than MC4
Bearings 96 4800 Groove with Clearance Greater
223 D Contact Angle E Spherical Thrust Snap Ring MC6 than MC5
: /500 5000 about 28 Roller Bearings in Outer
Ring PN0 Class 0
511 Thrust Ball /530 5300 Clearance in Deep Groove
Bearing with CM Ball Bearings for Electric
512 Flat Seats /560 5600 Motors
513 PN00 Class 00

: CT Clearance in Cylindrical
Roller Bearings for Electric
292 Thrust CM Motors
Spherical /2 360 2 360 00
293 Roller
/2 500 2 500 00
294
:
Bearings
(Preload of Angular Contact
Ball Bearing )
EL Extra light Preload
HR(4) High Capacity L Light Preload
Tapered Roller
Bearings, and others M Medium Preload
H Heavy Preload
Partially the Partially the
Same as
Symbols and Numbers Conform to JIS(5) NSK Symbol NSK Symbol same as
JIS(5)
NSK Symbol same as JIS(5)/ Same as JIS(5) NSK Symbol, Partially the same as JIS(5)
JIS(5) BAS(6)
Marked on Bearings Not Marked In Principle, Marked on Bearings Not Marked on Bearings
on Bearings
Notes ( ) Bearing Series Symbols conform to Table 7.5.
1 Notes ( ) JIS : Japanese Industrial Standards.
5
(2) For basic numbers of tapered roller bearings in ISO's new series, refer to Page B111. (6) BAS : The Japan Bearing Industrial Association Standard.
(3) For Bearing Bore Numbers 04 through 96, five times the bore number gives the bore size (mm) (except double- (7) ABMA : The American Bearing Manufacturers Association.
direction thrust ball bearings).
(4) HR is prefix to bearing series symbols and it is NSK's original prefix.
A 56 A 57
A024-057E.indd 56-57 11/20/13 4:50:38 PM

8. BEARING TOLERANCES
8.1 Bearing Tolerance Standards Regarding bearing accuracy classes, besides ISO (Reference) Rough definitions of the items listed for Supplementary Table
The tolerances for the boundary dimensions and normal accuracy, as the accuracy improves there Running Accuracy and their measuring methods are Running Inner Outer Dial
running accuracy of rolling bearings are specified by are Class 6X (for tapered roller bearings), Class 6, shown in Fig. 8.1, and they are described in detail in Accuracy Ring Ring Gauge
ISO 492/199/582 (Accuracies of Rolling Bearings). Class 5, Class 4, and Class 2, with Class 2 being the ISO 5593 (Rolling Bearings-Vocabulary) and JIS B K ia Rotating Stationary A
Tolerances are specified for the following items: highest in ISO. The applicable accuracy classes for 1515 (Rolling Bearings-Tolerances) and elsewhere.
K ea Stationary Rotating A
each bearing type and the correspondence of these
classes are shown in Table 8.1. S ia Rotating Stationary B1
S ea Stationary Rotating B2
Tolerances for bore and outside diameters, ring width
Tolerances for Dimensions and bearing width A
( ) Measuring Sd Rotating Stationary C

Items necessary to mount Tolerances for inscribed and circumscribed circle B2
Weight SD Rotating D
bearings on shafts or in diameters of rollers
housings Tolerances for chamfer dimensions Only the shaft or housing
C
Tolerances for width variation Si , Se or central washer is to be E
Tolerances for tapered bore diameters rotated.
Accuracy of Rolling Bearings A
Permissible radial runout of inner and outer rings
Running Accuracy Permissible face runout with raceway inner and outer
( Items necessary to
specify the runout of
rotating machine parts
) rings
Permissible inner ring face runout with bore
Permissible outer ring variation of outside surface
generatrix inclination with face
C
E
Permissible raceway to back face thickness variation of Measuring
B1 r (max.)1.2
thrust bearings Weight D
Table 8. 1 Bearing Types and Tolerance Classes

Supporting pins
r (max.)1.2 Stops at two points for at three points around
Applicable Reference Stops (at two points) inside or outside surface circumference
Bearing Types Applicable Tolerance Classes Tables Pages
Fig. 8.1 Measuring Methods for Running Accuracy (summarized)
Deep Groove Ball Bearings Normal Class 6 Class 5 Class 4 Class 2
Angular Contact Ball Bearings Normal Class 6 Class 5 Class 4 Class 2

Class 6 Class 5
Symbols for Boundary Dimensions and Running Accuracy
Self-Aligning Ball Bearings Normal equivalent equivalent Table A60
8.2 to A63 d Brg bore dia., nominal D Brg outside dia., nominal
Cylindrical Roller Bearings Normal Class 6 Class 5 Class 4 Class 2 & ds Deviation of a single bore dia. & Ds Deviation of a single outside dia.
Needle Roller Bearings & dmp Single plane mean bore dia. deviation & Dmp Single plane mean outside dia. Deviation
Normal Class 6 Class 5 Class 4
(solid type) Vdp Bore dia. Variation in a single radial plane VDp Outside dia. Variation in a single radial
Spherical Roller Bearings Normal Class 6 Class 5 Vdmp Mean bore dia. Variation plane
VDmp Mean outside dia. Variation
Metric Normal Table A64
Tapered Design Class 6X Class 5 Class 4 8.3 to A67 B Inner ring width, nominal
Roller & Bs Deviation of a single inner ring width C Outer ring width, nominal
Bearings ANSI/ABMA ANSI/ABMA ANSI/ABMA ANSI/ABMA ANSI/ABMA Table A68
Inch Design CLASS 4 CLASS 2 CLASS 3 CLASS 0 CLASS 00 8.4 and A69 VBs Inner ring width variation & Cs Deviation of a single outer ring width
Magneto Bearings Normal Class 6 Class 5 Table A70 VCs Outer ring width variation
8.5 and A71 Kia Radial runout of assembles brg inner ring
Table A72
Thrust Ball Bearings Normal Class 6 Class 5 Class 4 8.4 to A74 Sd inner ring reference face (backface, where Kea Radial runout of assembled brg outer ring
Table applicable) runout with bore SD Variation of brg outside surface generatrix
Thrust Spherical Roller Bearings Normal 8.7 A75 Sia Assembled brg inner ring face (back face) inclination with outer ring reference face
JIS(1) Class 0 Class 6 Class 5 Class 4 Class 2
runout with raceway (backface)
Si, Se Raceway to backface thickness variation Sea Assembled brg outer ring face (backface)
Equivalent standards
DIN(2) P0 P6 P5 P4 P2 of thrust brg runout with raceway

(Reference)
Ball ABEC 5 ABEC 7 ABEC 9 Table A60

Bearings ABEC 1 ABEC 3 (CLASS 5P) (CLASS 7P) (CLASS 9P) T Brg width, nominal C T
8.2 to A63
(A76 Deviation of the actual brg width
ANSI/
ABMA(3)
Roller
Bearings RBEC 1 RBEC 3 RBEC 5 [ Table
8.8 ] and A77)
& Ts
Tapered Roller
Bearings CLASS 4 CLASS 2 CLASS 3 CLASS 0 CLASS 00 [ Table
8.4 ] (A68
and A69)
Notes (1) JIS : Japanese Industrial Standards (2) DIN : Deutsch Industrie Norm B
jd jD
(3) ANSI/ABMA : The American Bearing Manufacturers Association
Remarks The permissible limit of chamfer dimensions shall conform to Table 8.9 (Page A78), and the tolerances and permissible
tapered bore diameters shall conform to Table 8.10 (Page A80).
A 58 A 59
A058-081E.indd 58-59 11/20/13 4:51:06 PM

BEARING TOLERANCES
BEARING TOLERANCE
Table 8. 2 Tolerances for Radial Bearings (excluding Tapered Roller Bearings)

Table 8. 2. 1 Tolerances for Inner Rings and Widths of Outer Rings
& dmp (2) & ds (2) V dp (2) V dmp (2)

Nominal Bore Diameter
d Class 4 Normal Class 6 Class 5 Class 4 Class 2
(mm) Normal Class 6 Class 5 Class 4 Class 2 Diameter Class 2 Diameter Series Diameter Series Diameter Diameter Diameter Normal Class Class Class Class
Series Series Series Series 6 5 4 2
0, 1, 2, 3, 4 9 0, 1 2, 3, 4 9 0, 1 2, 3, 4 9 0,1,2,3,4 9 0,1,2,3,4 0,1,2,3,4
over incl. high low high low high low high low high low high low high low max. max. max. max. max. max. max. max. max. max.
0.6(1) 2.5 0 - 8 0 - 7 0 - 5 0 - 4 0 -2.5 0 - 4 0 -2.5 10 8 6 9 7 5 5 4 4 3 2.5 6 5 3 2 1.5
2.5 10 0 - 8 0 - 7 0 - 5 0 - 4 0 -2.5 0 - 4 0 -2.5 10 8 6 9 7 5 5 4 4 3 2.5 6 5 3 2 1.5
10 18 0 - 8 0 - 7 0 - 5 0 - 4 0 -2.5 0 - 4 0 -2.5 10 8 6 9 7 5 5 4 4 3 2.5 6 5 3 2 1.5
18 30 0 - 10 0 - 8 0 - 6 0 - 5 0 -2.5 0 - 5 0 -2.5 13 10 8 10 8 6 6 5 5 4 2.5 8 6 3 2.5 1.5
30 50 0 - 12 0 -10 0 - 8 0 - 6 0 -2.5 0 - 6 0 -2.5 15 12 9 13 10 8 8 6 6 5 2.5 9 8 4 3 1.5
50 80 0 - 15 0 -12 0 - 9 0 - 7 0 -4 0 - 7 0 -4 19 19 11 15 15 9 9 7 7 5 4 11 9 5 3.5 2
80 120 0 - 20 0 -15 0 -10 0 - 8 0 -5 0 - 8 0 -5 25 25 15 19 19 11 10 8 8 6 5 15 11 5 4 2.5
120 150 0 - 25 0 -18 0 -13 0 -10 0 -7 0 -10 0 -7 31 31 19 23 23 14 13 10 10 8 7 19 14 7 5 3.5
150 180 0 - 25 0 -18 0 -13 0 -10 0 -7 0 -10 0 -7 31 31 19 23 23 14 13 10 10 8 7 19 14 7 5 3.5
180 250 0 - 30 0 -22 0 -15 0 -12 0 -8 0 -12 0 -8 38 38 23 28 28 17 15 12 12 9 8 23 17 8 6 4
250 315 0 - 35 0 -25 0 -18 - - - - - - - - 44 44 26 31 31 19 18 14 - - - 26 19 9 - -
315 400 0 - 40 0 -30 0 -23 - - - - - - - - 50 50 30 38 38 23 23 18 - - - 30 23 12 - -
400 500 0 - 45 0 -35 - - - - - - - - - - 56 56 34 44 44 26 - - - - - 34 26 - - -
500 630 0 - 50 0 -40 - - - - - - - - - - 63 63 38 50 50 30 - - - - - 38 30 - - -
630 800 0 - 75 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
800 1 000 0 -100 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 000 1 250 0 -125 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 250 1 600 0 -160 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 600 2 000 0 -200 - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Units : m
& Bs (or & Cs )(

3 ) V B s (or V C s ) K ia Sd S ia (5)
Single Bearing Combined Bearings (4) Inner Ring (or Inner Ring d
Outer Ring) (3)
Normal Class 6 Class 5 Class 4 Class 2 Class 5 Class 4 Class 2 Class 5 Class 4 Class 2 (mm)
Normal Class 5 Normal Class 5
Normal Class
Class Class Class
Class 6 Class 4 Class 2 Class 6 Class 4 Class 2 6 5 4 2
high low high low high low high low high low high low max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. over incl.
0 - 40 0 - 40 0 - 40 0 -250 0 -250 12 12 5 2.5 1.5 10 5 4 2.5 1.5 7 3 1.5 7 3 1.5 0.6(1) 2.5
0 - 120 0 - 40 0 - 40 0 -250 0 -250 0 -250 15 15 5 2.5 1.5 10 6 4 2.5 1.5 7 3 1.5 7 3 1.5 2.5 10
0 - 120 0 - 80 0 - 80 0 -250 0 -250 0 -250 20 20 5 2.5 1.5 10 7 4 2.5 1.5 7 3 1.5 7 3 1.5 10 18
0 - 120 0 -120 0 -120 0 -250 0 -250 0 -250 20 20 5 2.5 1.5 13 8 4 3 2.5 8 4 1.5 8 4 2.5 18 30
0 - 120 0 -120 0 -120 0 -250 0 -250 0 -250 20 20 5 3 1.5 15 10 5 4 2.5 8 4 1.5 8 4 2.5 30 50
0 - 150 0 -150 0 -150 0 -380 0 -250 0 -250 25 25 6 4 1.5 20 10 5 4 2.5 8 5 1.5 8 5 2.5 50 80
0 - 200 0 -200 0 -200 0 -380 0 -380 0 -380 25 25 7 4 2.5 25 13 6 5 2.5 9 5 2.5 9 5 2.5 80 120
0 - 250 0 -250 0 -250 0 -500 0 -380 0 -380 30 30 8 5 2.5 30 18 8 6 2.5 10 6 2.5 10 7 2.5 120 150
0 - 250 0 -250 0 -250 0 -500 0 -380 0 -380 30 30 8 5 4 30 18 8 6 5 10 6 4 10 7 5 150 180
0 - 300 0 -300 0 -300 0 -500 0 -500 0 -500 30 30 10 6 5 40 20 10 8 5 11 7 5 13 8 5 180 250
0 - 350 0 -350 - - 0 -500 0 -500 - - 35 35 13 - - 50 25 13 - - 13 - - 15 - - 250 315
0 - 400 0 -400 - - 0 -630 0 -630 - - 40 40 15 - - 60 30 15 - - 15 - - 20 - - 315 400
0 - 450 - - - - - - - - - - 50 45 - - - 65 35 - - - - - - - - - 400 500
0 - 500 - - - - - - - - - - 60 50 - - - 70 40 - - - - - - - - - 500 630
0 - 750 - - - - - - - - - - 70 - - - - 80 - - - - - - - - - - 630 800
0 -1 000 - - - - - - - - - - 80 - - - - 90 - - - - - - - - - - 800 1 000
0 -1 250 - - - - - - - - - - 100 - - - - 100 - - - - - - - - - - 1 000 1 250
0 -1 600 - - - - - - - - - - 120 - - - - 120 - - - - - - - - - - 1 250 1 600
0 -2 000 - - - - - - - - - - 140 - - - - 140 - - - - - - - - - - 1 600 2 000
Notes (1) 0.6mm is included in the group. Remarks 1. The cylindrical bore diameter "no-go side" tolerance limit (high) specified in this table does not necessarily apply
(2) Applicable to bearings with cylindrical bores. within a distance of 1.2 times the chamfer dimension r (max.) from the ring face.
(3) Tolerance for width deviation and tolerance limits for the width variation of the outer ring should be the same bearing. 2. ABMA Std 20-1996: ABEC1RBEC1, ABEC3RBEC3, ABEC5RBEC5, ABEC7RBEC7, and ABEC9RBEC9
Tolerances for the width variation of the outer ring of Class 5, 4, and 2 are shown in Table 8.2.2. are equivalent to Classes Normal, 6, 5, 4, and 2 respectively.
(4) Applicable to individual rings manufactured for combined bearings.
(5) Applicable to ball bearings such as deep groove ball bearings, angular contact ball bearings, etc.
A 60 A 61
A058-081E.indd 60-61 11/20/13 4:51:07 PM

BEARING TOLERANCES
BEARING TOLERANCE
Table 8. 2 Tolerances for Radial Bearings (excluding Tapered Roller Bearings)

Table 8. 2. 2 Tolerances for Outer Rings
& Dmp & Ds V Dp (2) V Dmp (2)

Nominal Outside
Diameter Normal Class 6 Class 5 Class 4 Class 2
Class 4
D Open Type Shielded Open Type Shielded Open Type Open Type Open Type
(mm) Normal Class 6 Class 5 Class 4 Class 2 Class 2 Sealed Sealed
Normal Class
6
Class Class
5 4
Class
2
Diameter Diameter Series Diameter Series Diameter Diameter Diameter
Series Series Series Series
0, 1, 2, 3, 4 9 0, 1 2, 3, 4 2, 3, 4 9 0, 1 2, 3, 4 0,1,2,3,4 9 0,1,2,3,4 9 0,1,2,3,4 0,1,2,3,4
over incl. high low high low high low high low high low high low high low max. max. max. max. max. max. max. max. max. max.
2.5(1) 6 0 - 8 0 -7 0 -5 0 - 4 0 - 2.5 0 - 4 0 - 2.5 10 8 6 10 9 7 5 9 5 4 4 3 2.5 6 5 3 2 1.5
6 18 0 - 8 0 - 7 0 -5 0 - 4 0 - 2.5 0 - 4 0 - 2.5 10 8 6 10 9 7 5 9 5 4 4 3 2.5 6 5 3 2 1.5
18 30 0 - 9 0 - 8 0 -6 0 - 5 0 - 4 0 - 5 0 - 4 12 9 7 12 10 8 6 10 6 5 5 4 4 7 6 3 2.5 2
30 50 0 - 11 0 - 9 0 -7 0 - 6 0 - 4 0 - 6 0 - 4 14 11 8 16 11 9 7 13 7 5 6 5 4 8 7 4 3 2
50 80 0 - 13 0 -11 0 -9 0 - 7 0 - 4 0 - 7 0 - 4 16 13 10 20 14 11 8 16 9 7 7 5 4 10 8 5 3.5 2
80 120 0 - 15 0 -13 0 -10 0 - 8 0 - 5 0 - 8 0 - 5 19 19 11 26 16 16 10 20 10 8 8 6 5 11 10 5 4 2.5
120 150 0 - 18 0 -15 0 -11 0 - 9 0 - 5 0 - 9 0 - 5 23 23 14 30 19 19 11 25 11 8 9 7 5 14 11 6 5 2.5
150 180 0 - 25 0 -18 0 -13 0 -10 0 -7 0 -10 0 -7 31 31 19 38 23 23 14 30 13 10 10 8 7 19 14 7 5 3.5
180 250 0 - 30 0 -20 0 -15 0 -11 0 - 8 0 -11 0 -8 38 38 23 - 25 25 15 - 15 11 11 8 8 23 15 8 6 4
250 315 0 - 35 0 -25 0 -18 0 -13 0 - 8 0 -13 0 - 8 44 44 26 - 31 31 19 - 18 14 13 10 8 26 19 9 7 4
315 400 0 - 40 0 -28 0 -20 0 -15 0 -10 0 -15 0 -10 50 50 30 - 35 35 21 - 20 15 15 11 10 30 21 10 8 5
400 500 0 - 45 0 -33 0 -23 - - - - - - - - 56 56 34 - 41 41 25 - 23 17 - - - 34 25 12 - -
500 630 0 - 50 0 -38 0 -28 - - - - - - - - 63 63 38 - 48 48 29 - 28 21 - - - 38 29 14 - -
630 800 0 - 75 0 -45 0 -35 - - - - - - - - 94 94 55 - 56 56 34 - 35 26 - - - 55 34 18 - -
800 1 000 0 -100 0 -60 - - - - - - - - - - 125 125 75 - 75 75 45 - - - - - - 75 45 - - -
1 000 1 250 0 -125 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 250 1 600 0 -160 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
1 600 2 000 0 -200 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
2 000 2 500 0 -250 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Notes (1) 2.5mm is included in the group.
(2) Applicable only when a locating snap ring is not used.
(3) Applicable to ball bearings such as deep groove ball bearings and angular contact ball bearings. Units : m
(4) The tolerances for outer ring width variation of bearings of Classes Normal and 6 are shown in Table 8.2.1.
Remarks 1. The outside diameter "no-go side" tolerances (low) specified in this table do not necessarily apply within a distance K ea SD S ea (3) V Cs (4)
of 1.2 times the chamfer dimension r (max.) from the ring face. Nominal Outside
2. ABMA Std 20-1996: ABEC1RBEC1, ABEC3RBEC3, ABEC5RBEC5, ABEC7RBEC7, and ABEC9 RBEC9
Diameter
are equivalent to Classes Normal, 6, 5, 4, and 2 respectively.
D
Normal Class
6
Class Class
5 4
Class
2
Class Class
5 4
Class
2
Class Class
5 4
Class
2
Class
5
Class
4
Class
2 (mm)
max. max. max. max. max. max. max. max. max. max. max. max. max. max. over incl.
15 8 5 3 1.5 8 4 1.5 8 5 1.5 5 2.5 1.5 2.5 (1) 6
15 8 5 3 1.5 8 4 1.5 8 5 1.5 5 2.5 1.5 6 18
15 9 6 4 2.5 8 4 1.5 8 5 2.5 5 2.5 1.5 18 30
20 10 7 5 2.5 8 4 1.5 8 5 2.5 5 2.5 1.5 30 50
25 13 8 5 4 8 4 1.5 10 5 4 6 3 1.5 50 80
35 18 10 6 5 9 5 2.5 11 6 5 8 4 2.5 80 120
40 20 11 7 5 10 5 2.5 13 7 5 8 5 2.5 120 150
45 23 13 8 5 10 5 2.5 14 8 5 8 5 2.5 150 180
50 25 15 10 7 11 7 4 15 10 7 10 7 4 180 250
60 30 18 11 7 13 8 5 18 10 7 11 7 5 250 315
70 35 20 13 8 13 10 7 20 13 8 13 8 7 315 400
80 40 23 - - 15 - - 23 - - 15 - - 400 500
100 50 25 - - 18 - - 25 - - 18 - - 500 630
120 60 30 - - 20 - - 30 - - 20 - - 630 800
140 75 - - - - - - - - - - - - 800 1 000
160 - - - - - - - - - - - - - 1 000 1 250
190 - - - - - - - - - - - - - 1 250 1 600
220 - - - - - - - - - - - - - 1 600 2 000
250 - - - - - - - - - - - - - 2 000 2 500
A 62 A 63
A058-081E.indd 62-63 11/20/13 4:51:08 PM

BEARING TOLERANCES
BEARING TOLERANCE
Table 8. 3 Tolerances for Metric Design Tapered Roller Bearings

Table 8. 3. 1 Tolerances for Inner Ring Bore Diameter and Running Accuracy
Units : m
Nominal Bore & dmp & ds V dp V dmp K ia Sd S ia

Diameter T
d Normal Class 6 Normal Class Class Class Normal Class Class Class Normal Class Class Class Class Class Class
C
(mm) Class 4 Class 4
Class 6X Class 5 Class 6X 6 5 4 Class 6X 6 5 4 Class 6X 6 5 4 5 4 4
over incl. high low high low high low high low max. max. max. max. max. max. max. max. max. max. max. max. max. max. max.
B
10 18 0 - 8 0 - 7 0 - 5 0 - 5 8 7 5 4 6 5 5 4 15 7 3.5 2.5 7 3 3 jd jD
18 30 0 -10 0 - 8 0 - 6 0 - 6 10 8 6 5 8 6 5 4 18 8 4 3 8 4 4
30 50 0 -12 0 -10 0 - 8 0 - 8 12 10 8 6 9 8 5 5 20 10 5 4 8 4 4
50 80 0 -15 0 -12 0 - 9 0 - 9 15 12 9 7 11 9 6 5 25 10 5 4 8 5 4
80 120 0 -20 0 -15 0 -10 0 -10 20 15 11 8 15 11 8 5 30 13 6 5 9 5 5
120 180 0 -25 0 -18 0 -13 0 -13 25 18 14 10 19 14 9 7 35 18 8 6 10 6 7
180 250 0 -30 0 -22 0 -15 0 -15 30 22 17 11 23 16 11 8 50 20 10 8 11 7 8
250 315 0 -35 0 -25 0 -18 0 -18 35 - - - 26 - - - 60 25 13 10 13 8 10
315 400 0 -40 0 -30 0 -23 0 -23 40 - - - 30 - - - 70 30 15 12 15 10 14
400 500 0 -45 0 -35 0 -27 0 -27 - - - - - - - - 70 35 18 14 19 13 17
500 630 0 -50 0 -40 - - - - - - - - - - - - 85 40 20 - 22 - - B2
630 800 0 -75 0 -60 - - - - - - - - - - - - 100 45 22 - 27 - - C
Remarks 1. The bore diameter "no-go side" tolerances (high) specified in this table do not necessarily apply within a distance
of 1.2 times the chamfer dimension r (max.) from the ring face.
2. Some of these tolerances conform to the NSK Standard.
jd jD
Table 8. 3. 2 Tolerances for Outer Ring Outside Diameter and Running Accuracy
Units : m
Nominal Outside & Dmp & Ds V Dp V Dmp K ea SD S ea

Diameter
D Normal Class 6 Normal Class Class Class Normal Class Class Class Normal Class Class Class Class Class Class
(mm) Class 4 Class 4
Class 6X Class 5 Class 6X 6 5 4 Class 6X 6 5 4 Class 6X 6 5 4 5 4 4
over incl. high low high low high low high low max. max. max. max. max. max. max. max. max. max. max. max. max. max. max.
C4
18 30 0 - 9 0 - 8 0 - 6 0 - 6 9 8 6 5 7 6 5 4 18 9 6 4 8 4 5
30 50 0 - 11 0 - 9 0 - 7 0 - 7 11 9 7 5 8 7 5 5 20 10 7 5 8 4 5
50 80 0 - 13 0 -11 0 - 9 0 - 9 13 11 8 7 10 8 6 5 25 13 8 5 8 4 5
80 120 0 - 15 0 -13 0 -10 0 -10 15 13 10 8 11 10 7 5 35 18 10 6 9 5 6 B4
120 150 0 - 18 0 -15 0 -11 0 -11 18 15 11 8 14 11 8 6 40 20 11 7 10 5 7 jd jD
150 180 0 - 25 0 -18 0 -13 0 -13 25 18 14 10 19 14 9 7 45 23 13 8 10 5 8
180 250 0 - 30 0 -20 0 -15 0 -15 30 20 15 11 23 15 10 8 50 25 15 10 11 7 10
250 315 0 - 35 0 -25 0 -18 0 -18 35 25 19 14 26 19 13 9 60 30 18 11 13 8 10
315 400 0 - 40 0 -28 0 -20 0 -20 40 28 22 15 30 21 14 10 70 35 20 13 13 10 13
400 500 0 - 45 0 -33 0 -23 0 -23 45 - - - 34 - - - 80 40 23 15 15 11 15
500 630 0 - 50 0 -38 0 -28 0 -28 50 - - - 38 - - - 100 50 25 18 18 13 18
630 800 0 - 75 0 -45 - - - - - - - - - - - - 120 60 30 - 20 - -
800 1 000 0 -100 0 -60 - - - - - - - - - - - - 120 75 35 - 23 - -
Remarks 1. The outside diameter "no-go side" tolerances (low) specified in this table do not necessarily apply within a distance
of 1.2 times the chamfer dimension r (max.) from the ring face.
2. Some of these tolerances conform to the NSK Standard.
A 64 A 65
A058-081E.indd 64-65 11/20/13 4:51:09 PM

BEARING TOLERANCES
BEARING TOLERANCE
Table 8. 3 Tolerances for Metric Design Tapered Roller Bearings

Table 8. 3. 3 Tolerances for Width, Overall Bearing Width, and Combined Bearing Width
Units : m
Ring Width with Rollers Outer Ring Effective Width Deviation Overall Combined Bearing Width Deviation
Nominal Bore & Bs & Cs & Ts Nominal Bore
& T 1s & T 2s & B 2s & B 4s , & C 4s
Diameter Diameter
d Normal Class 5 Normal Class 5 Normal Class 5 All classes of double- All classes of four-row
d
(mm) Class 6X Class 6X Class 6X Normal Class 6X Normal Class 6X (mm)
Class 6 Class 4 Class 6 Class 4 Class 6 Class 4 row bearings bearings
over incl. high low high low high low high low high low high low high low high low high low high low high low high low high low high low high low over incl.
10 18 0 -120 0 -50 0 -200 0 -120 0 -100 0 -200 +200 -200 +100 0 +200 -200 +100 -100 + 50 0 +100 -100 + 50 0 + 200 - 200 - - 10 18
18 30 0 -120 0 -50 0 -200 0 -120 0 -100 0 -200 +200 -200 +100 0 +200 -200 +100 -100 + 50 0 +100 -100 + 50 0 + 200 - 200 - - 18 30
30 50 0 -120 0 -50 0 -240 0 -120 0 -100 0 -240 +200 -200 +100 0 +200 -200 +100 -100 + 50 0 +100 -100 + 50 0 + 200 - 200 - - 30 50
50 80 0 -150 0 -50 0 -300 0 -150 0 -100 0 -300 +200 -200 +100 0 +200 -200 +100 -100 + 50 0 +100 -100 + 50 0 + 300 - 300 + 300 - 300 50 80
80 120 0 -200 0 -50 0 -400 0 -200 0 -100 0 -400 +200 -200 +100 0 +200 -200 +100 -100 + 50 0 +100 -100 + 50 0 + 300 - 300 + 400 - 400 80 120
120 180 0 -250 0 -50 0 -500 0 -250 0 -100 0 -500 +350 -250 +150 0 +350 -250 +150 -150 + 50 0 +200 -100 +100 0 + 400 - 400 + 500 - 500 120 180
180 250 0 -300 0 -50 0 -600 0 -300 0 -100 0 -600 +350 -250 +150 0 +350 -250 +150 -150 + 50 0 +200 -100 +100 0 + 450 - 450 + 600 - 600 180 250
250 315 0 -350 0 -50 0 -700 0 -350 0 -100 0 -700 +350 -250 +200 0 +350 -250 +150 -150 +100 0 +200 -100 +100 0 + 550 - 550 + 700 - 700 250 315
315 400 0 -400 0 -50 0 -800 0 -400 0 -100 0 -800 +400 -400 +200 0 +400 -400 +200 -200 +100 0 +200 -200 +100 0 + 600 - 600 + 800 - 800 315 400
400 500 0 -450 - - 0 -800 0 -450 - - 0 -800 +400 -400 - - +400 -400 - - - - - - - - + 700 - 700 + 900 - 900 400 500
500 630 0 -500 - - 0 -800 0 -500 - - 0 -800 +500 -500 - - +500 -500 - - - - - - - - + 800 - 800 +1 000 -1 000 500 630
630 800 0 -750 - - 0 -800 0 -750 - - 0 -800 +600 -600 - - +600 -600 - - - - - - - - +1 200 -1 200 +1 500 -1 500 630 800
Remarks The effective width of an inner ring with rollers T1 is defined as the overall bearing width of an inner ring with rollers
combined with a master outer ring.
Remarks The effective width of an outer ring T2 is defined as the overall bearing width of an outer ring combined with a master
inner ring with rollers.
T B2
C C C4 T1 T2
Master Master Inner Ring with Rollers
Outer Ring
B B4
jd jD jd jD jd jD jd jd
A 66 A 67
A058-081E.indd 66-67 11/20/13 4:51:10 PM

BEARING TOLERANCES
BEARING TOLERANCE
Table 8. 4 Tolerances for Inch Design Tapered Roller Bearings

(Refer to page A58 Table 8. 1 for the tolerance class "CLASS ** " that is the tolerance classes of ANSI/ABMA.)
Table 8. 4. 1 Tolerances for Inner Ring Bore Diameter
Units : m
T B2
Nominal Bore Diameter C C C4
& ds
d
over incl. CLASS 4, 2 CLASS 3, 0 CLASS 00
B B4
(mm) 1/25.4 (mm) 1/25.4 high low high low high low
jd jD jd jD jd jD
- - 76.200 3.0000 + 13 0 +13 0 +8 0
76.200 3.0000 266.700 10.5000 + 25 0 +13 0 +8 0
266.700 10.5000 304.800 12.0000 + 25 0 +13 0 - -
304.800 12.0000 609.600 24.0000 + 51 0 +25 0 - -

609.600 24.0000 914.400 36.0000 + 76 0 +38 0 - - KBE KV
914.400 36.0000 1 219.200 48.0000 +102 0 +51 0 - -
1 219.200 48.0000 - - +127 0 +76 0 - -
Table 8. 4. 2 Tolerances for Outer Ring Outside Diameter and Radial Runout of Inner and Outer Rings
Units : m
Nominal Outside Diameter

& Ds K ia , K ea
D
over incl. CLASS 4, 2 CLASS 3, 0 CLASS 00 CLASS 4 CLASS 2 CLASS 3 CLASS 0 CLASS 00
(mm) 1/25.4 (mm) 1/25.4 high low high low high low max. max. max. max. max.
- - 266.700 10.5000 + 25 0 +13 0 +8 0 51 38 8 4 2

266.700 10.5000 304.800 12.0000 + 25 0 +13 0 +8 0 51 38 8 4 2
304.800 12.0000 609.600 24.0000 + 51 0 +25 0 - - 51 38 18 - -
609.600 24.0000 914.400 36.0000 + 76 0 +38 0 - - 76 51 51 - -

914.400 36.0000 1 219.200 48.0000 +102 0 +51 0 - - 76 - 76 - -
1 219.200 48.0000 - - +127 0 +76 0 - - 76 - 76 - -
Table 8. 4. 3 Tolerances for Overall Width and Combined Width

Units : m
Nominal Bore Diameter Double-Row Bearings (KBE Type) Four-Row Bearings

d & Ts (KV Type)
& B 2s & B 4s , & C 4s
CLASS 3 CLASS 3
over incl. CLASS 4 CLASS 2 CLASS 0, 00 CLASS 4 CLASS 2 CLASS 0,00 CLASS 4, 3
D508.000 (mm) D>508.000 (mm) D508.000 (mm) D>508.000 (mm)
(mm) 1/25.4 (mm) 1/25.4 high low high low high low high low high low high low high low high low high low high low high low
- - 101.600 4.0000 +203 0 +203 0 +203 -203 +203 -203 +203 -203 +406 0 +406 0 +406 -406 +406 -406 +406 -406 +1 524 -1 524
101.600 4.0000 304.800 12.0000 +356 -254 +203 0 +203 -203 +203 -203 +203 -203 +711 -508 +406 -203 +406 -406 +406 -406 +406 -406 +1 524 -1 524
304.800 12.0000 609.600 24.0000 +381 -381 +381 -381 +203 -203 +381 -381 - - +762 -762 +762 -762 +406 -406 +762 -762 - - +1 524 -1 524
609.600 24.0000 - - +381 -381 - - +381 -381 +381 -381 - - +762 -762 - - +762 -762 +762 -762 - - +1 524 -1 524
A 68 A 69
A058-081E.indd 68-69 11/20/13 4:51:11 PM

BEARING TOLERANCES
Table 8. 5 Tolerances for Magneto Bearings

Table 8. 5. 1 Tolerances for Inner Rings and Width of Outer Rings
Units : m
Nominal Bore & dmp V dp V d mp & B s (or & Cs ) (1) V Bs (or V Cs ) (1) & Ts K ia Sd S ia
Diameter
d
(mm) Class Class Class Class Normal Normal Normal Class 6
Normal Class 6 Class 5 Normal Normal Class 5 Class 5 Normal Class 6 Class 5 Class 5 Class 5
6 5 6 5 Class 6 Class 6 Class 5
over incl. high low high low high low max. max. max. max. max. max. high low high low max. max. high low max. max. max. max. max.
2.5 10 0 - 8 0 -7 0 -5 6 5 4 6 5 3 0 -120 0 - 40 15 5 +120 -120 10 6 4 7 7
10 18 0 - 8 0 -7 0 -5 6 5 4 6 5 3 0 -120 0 - 80 20 5 +120 -120 10 7 4 7 7
18 30 0 -10 0 -8 0 -6 8 6 5 8 6 3 0 -120 0 -120 20 5 +120 -120 13 8 4 8 8
Note (1) The width deviation and width variation of an outer ring is determined according to the inner ring of the same
bearing.
Remarks The bore diameter "no-go side" tolerances (high) specified in this table do not necessarily apply within a distance of
1.2 times the chamfer dimension r (max.) from the ring face.
Table 8. 5. 2 Tolerances for Outer Rings

Units : m
& Dmp
Nominal Outside V Dp V Dmp K ea S ea SD
Diameter
Bearing Series E Bearing Series EN
D
(mm) Normal Class 6 Class 5 Normal Class 6 Class 5 Normal Class Class
Normal
Class Class
Normal
Class Class Class Class
6 5 6 5 6 5 5 5
over incl. high low high low high low high low high low high low max. max. max. max. max. max. max. max. max. max. max.
6 18 + 8 0 +7 0 +5 0 0 - 8 0 -7 0 -5 6 5 4 6 5 3 15 8 5 8 8
18 30 + 9 0 +8 0 +6 0 0 - 9 0 -8 0 -6 7 6 5 7 6 3 15 9 6 8 8
30 50 +11 0 +9 0 +7 0 0 -11 0 -9 0 -7 8 7 5 8 7 4 20 10 7 8 8
Remarks The outside diameter "no-go side" tolerances (low) do not necessarily apply within a distance of 1.2 times the
chamfer dimension r (max.) from the ring face.
A 70 A 71
A058-081E.indd 70-71 11/20/13 4:51:12 PM

BEARING TOLERANCES
Table 8. 6 Tolerances for Thrust Ball Bearings

Table 8. 6. 1 Tolerances for Shaft Washer Bore Diameter and Running Accuracy Table 8. 6. 2 Tolerances for Outside Diameter of Housing Washers and Aligning Seat Washers
Units : m Units : m
Aligning Seat Washer
Nominal Outside Diameter of & Dmp Outside Diameter
Nominal Bore & d mp or & d 2 mp V d p or V d 2 p S i or S e (1) V Dp
Bearing or Aligning Deviation
Diameter Aligning Seat
Seat Washer Flat Seat Type Washer Type & D 3s
d or d2
Normal Normal D or D3 Normal Normal
(mm) Class Class Class Class Normal Normal
Class 6 Class 4 Class 6 Normal (mm) Class 6 Class 4 Class 6 Class 4
Class 5 Class 5 4 6 5 4 Class 6 Class 6
Class 5 Class 5
over incl. high low high low max. max. max. max. max. max. over incl. high low high low high low max. max. high low
- 18 0 - 8 0 -7 6 5 10 5 3 2 10 18 0 - 11 0 - 7 0 - 17 8 5 0 - 25
18 30 0 - 10 0 - 8 8 6 10 5 3 2 18 30 0 - 13 0 - 8 0 - 20 10 6 0 - 30
30 50 0 - 12 0 -10 9 8 10 6 3 2 30 50 0 - 16 0 - 9 0 - 24 12 7 0 - 35
50 80 0 - 15 0 -12 11 9 10 7 4 3 50 80 0 - 19 0 -11 0 - 29 14 8 0 - 45
80 120 0 - 20 0 -15 15 11 15 8 4 3 80 120 0 - 22 0 -13 0 - 33 17 10 0 - 60
120 180 0 - 25 0 -18 19 14 15 9 5 4 120 180 0 - 25 0 -15 0 - 38 19 11 0 - 75
180 250 0 - 30 0 -22 23 17 20 10 5 4 180 250 0 - 30 0 -20 0 - 45 23 15 0 - 90

250 315 0 - 35 0 -25 26 19 25 13 7 5 250 315 0 - 35 0 -25 0 - 53 26 19 0 -105
315 400 0 - 40 0 -30 30 23 30 15 7 5 315 400 0 - 40 0 -28 0 - 60 30 21 0 -120
400 500 0 - 45 0 -35 34 26 30 18 9 6 400 500 0 - 45 0 -33 0 - 68 34 25 0 -135
500 630 0 - 50 0 -40 38 30 35 21 11 7 500 630 0 - 50 0 -38 0 - 75 38 29 0 -180
630 800 0 - 75 0 -50 - - 40 25 13 8 630 800 0 - 75 0 -45 0 -113 55 34 0 -225
800 1 000 0 -100 - - - - 45 30 15 - 800 1 000 0 -100 - - - - 75 - - -
1 000 1 250 0 -125 - - - - 50 35 18 - 1 000 1 250 0 -125 - - - - - - - -
1 250 1 600 0 -160 - - - - - - - -
Note (1) For double-direction bearings, the thickness variation doesn't depend on the bore diameter d2 , but on d for single-
direction bearings with the same D in the same diameter series.
The thickness variation of housing washers, Se, applies only to flat-seat thrust bearings.
jd jd jD
jd
T T3 T4 T6
B jd2 T1 T5 B jd 2 T7
jD T2 jD T8
jD3
jD jD 3
A 72 A 73
A058-081E.indd 72-73 11/20/13 4:51:13 PM

BEARING TOLERANCES
Table 8. 6. 3 Tolerances for Thrust Ball Bearing Height and Central Washer Height Table 8. 7 Tolerances for Thrust Spherical Roller Bearings
Units : m
Table 8. 7. 1 Tolerances for Bore Diameters of Shaft Rings and Height (Class Normal)
Nominal Bore Flat Seat Type Aligning Seat Washer Type With Aligning Seat Washer Height Deviation
of Central Washer Units : m
Diameter & Ts or & T 2 s & T1s & T 3 s or & T 6 s & T5s & T 4 s or & T 8 s & T7s & Bs
Nominal Bore Reference
d (1) Normal, Class 6 Normal, Class 6 Normal Normal Normal Normal Normal, Class 6 Diameter
(mm) & dmp V dp
Class 5, Class 4 Class 5, Class 4 Class 6 Class 6 Class 6 Class 6 Class 5, Class 4 d Sd & Ts
(mm)
over incl. high low high low high low high low high low high low high low
over incl. high low max. max. high low
- 30 0 - 75 + 50 -150 0 - 75 + 50 -150 + 50 - 75 +150 -150 0 - 50
30 50 0 -100 + 75 -200 0 -100 + 75 -200 + 50 -100 +175 -200 0 - 75 50 80 0 -15 11 25 +150 -150
50 80 0 -125 +100 -250 0 -125 +100 -250 + 75 -125 +250 -250 0 -100 80 120 0 -20 15 25 +200 -200
120 180 0 -25 19 30 +250 -250
80 120 0 -150 +125 -300 0 -150 +125 -300 + 75 -150 +275 -300 0 -125
120 180 0 -175 +150 -350 0 -175 +150 -350 +100 -175 +350 -350 0 -150 180 250 0 -30 23 30 +300 -300
180 250 0 -200 +175 -400 0 -200 +175 -400 +100 -200 +375 -400 0 -175 250 315 0 -35 26 35 +350 -350
315 400 0 -40 30 40 +400 -400
250 315 0 -225 +200 -450 0 -225 +200 -450 +125 -225 +450 -450 0 -200
315 400 0 -300 +250 -600 0 -300 +250 -600 +150 -275 +550 -550 0 -250 400 500 0 -45 34 45 +450 -450
Note (1) For double-direction bearings, its classification depends on d for single-direction bearings with the same D in the Remarks The bore diameter "no-go side" tolerances (high) specified in this table do not
same diameter series. necessarily apply within a distance of 1.2 times the chamfer dimension r (max.)
Remarks & Ts in the table is the deviation in the respective heights T in figures below. from the ring face.
Table 8. 7. 2 Tolerances for Housing Ring

Diameter (Class Normal)
Units : m
Nominal Outside Diameter
D & Dmp
(mm)
over incl. high low
jd -
jd 120 180 0 25
180 250 0 - 30
T 250 315 0 - 35
T3 T4
jD 315 400 0 - 40
jD 400 500 0 - 45
jD3 500 630 0 - 50
630 800 0 - 75
800 1 000 0 -100
jd
Remarks The outside diameter "no-go side"
jD tolerances (low) specified in this
B jd2 T1 table do not necessarily apply
T2 within a distance of 1.2 times the
T6 chamfer dimension r (max.) from
T5 B jd 2 T7
jD T8 the ring face.
jD 3
jd
jD
A 74 A 75
A058-081E.indd 74-75 11/20/13 4:51:14 PM

BEARING TOLERANCES
Table 8. 8 Tolerances of Instrument Ball Bearings (Inch design)
CLASS 5P, CLASS 7P, and CLASS 9P (ANSI/ABMA Equivalent)
(1) Tolerances for Inner Rings and Width of Outer Rings

Units : m
Nominal & d mp & ds V dp V d mp & Bs (or & Cs ) V Bs K ia S ia Sd

Bore
Diameter Single Brgs Combined Brgs (1)
d CLASS 5P
CLASS 9P
CLASS 5P
CLASS 9P CLASS 5P CLASS 5P CLASS CLASS CLASS CLASS CLASS CLASS CLASS CLASS CLASS CLASS CLASS CLASS
CLASS 7P CLASS 7P CLASS 7P CLASS 9P CLASS 7P CLASS 9P CLASS 5P CLASS 5P 5P 7P 9P 5P 7P 9P 5P 7P 9P 5P 7P 9P
(mm) CLASS 7P CLASS 7P
CLASS 9P CLASS 9P
over incl. high low high low high low high low max. max. max. max. high low high low max. max. max. max. max. max. max. max. max. max. max. max.
- 10 0 -5.1 0 -2.5 0 -5.1 0 -2.5 2.5 1.3 2.5 1.3 0 -25.4 0 -400 5.1 2.5 1.3 3.8 2.5 1.3 7.6 2.5 1.3 7.6 2.5 1.3
10 18 0 -5.1 0 -2.5 0 -5.1 0 -2.5 2.5 1.3 2.5 1.3 0 -25.4 0 -400 5.1 2.5 1.3 3.8 2.5 1.3 7.6 2.5 1.3 7.6 2.5 1.3
18 30 0 -5.1 0 -2.5 0 -5.1 0 -2.5 2.5 1.3 2.5 1.3 0 -25.4 0 -400 5.1 2.5 1.3 3.8 3.8 2.5 7.6 3.8 1.3 7.6 3.8 1.3
Note ( ) Applicable to bearings for which the axial clearance (preload) is to be adjusted by combining two selected bearings.
1
Remarks For the CLASS 3P and the tolerances of Metric design Instrument Ball Bearings, it is advisable to consult NSK.
(2) Tolerances for Outer Rings

Units : m
Flange
& D mp & Ds V Dp V D mp V Cs ( ) 1 SD K ea S ea Deviation of Backface
Nominal Deviation of
Flange Outside Runout
Outside Flange Width with
Diameter
Diameter CLASS 5P CLASS 5P CLASS CLASS 5P CLASS & C 1s Raceway
CLASS 7P CLASS 9P CLASS 7P 9P CLASS 7P 9P & D 1s
D (2) S ea 1
CLASS 5P CLASS CLASS CLASS CLASS CLASS CLASS CLASS CLASS CLASS CLASS CLASS CLASS
CLASS 9P 5P 7P 9P 5P 7P 9P 5P 7P 9P 5P 7P 9P
(mm) CLASS 7P Shielded
Open Open Open Shielded Open Open Shielded Open CLASS 5P CLASS 5P CLASS 5P
Sealed Sealed Sealed CLASS 7P CLASS 7P CLASS 7P
over incl. high low high low high low high low high low max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. high low high low max.
- 18 0 -5.1 0 -2.5 0 -5.1 +1 -6.1 0 -2.5 2.5 5.1 1.3 2.5 5.1 1.3 5.1 2.5 1.3 7.6 3.8 1.3 5.1 3.8 1.3 7.6 5.1 1.3 0 -25.4 0 -50.8 7.6
18 30 0 -5.1 0 -3.8 0 -5.1 +1 -6.1 0 -3.8 2.5 5.1 2 2.5 5.1 2 5.1 2.5 1.3 7.6 3.8 1.3 5.1 3.8 2.5 7.6 5.1 2.5 0 -25.4 0 -50.8 7.6
30 50 0 -5.1 0 -3.8 0 -5.1 +1 -6.1 0 -3.8 2.5 5.1 2 2.5 5.1 2 5.1 2.5 1.3 7.6 3.8 1.3 5.1 5.1 2.5 7.6 5.1 2.5 0 -25.4 0 -50.8 7.6
Notes ( ) Applicable to flange width variation for flanged bearings.

1
(2) Applicable to flange back face.
A 76 A 77
A058-081E.indd 76-77 11/20/13 4:51:15 PM

BEARING TOLERANCES
r (max.) or r1 (max.) Table 8. 9 Chamfer Dimension Limits (for Metric Design Bearings)
r (min.) or
Table 8. 9. 1 Chamfer Dimension Limits for Radial Table 8. 9. 2 Chamfer Dimension Limits for Table 8. 9. 3 Chamfer Dimension Limits for Thrust Bearings
r1 (min.)
(Axial Direction)
r (min.) or Bore Surface or Bearings (excluding Tapered Tapered Roller Bearings
r1 (min.) Outside Surface Roller Bearings) Units : mm Units : mm Units : mm
r (max.) or r1 (max.)
(Radial Direction)
Permissible Reference Permissible Reference Permissible Chamfer Reference

Permissible Chamfer Nominal Bore or Permissible Chamfer Permissible Chamfer Dimension for Shaft
Chamfer Nominal Bore Corner Chamfer Corner
r (min.) or Dimension Dimension for Dimension Nominal Outside Dimension for Inner/ Dimension for Shaft (or Central)/Housing Corner Radius of
Diameter Radius of Radius of
Inner/Outer Rings Diameter (1) Outer Rings
r1 (min.) for Inner/ d r (max.) or r1 (max.) Shaft or
for Inner/
d or D r (max.) Shaft or
(or Central)/Housing Washers Shaft or Housing
Outer Rings
Housing ra
Outer
Housing ra
Washers r (max.) or r1 (max.) ra
r (min.) or Rings r (min.) or r1 (min.)
r1 (min.) over incl. Radial Axial max. r (min.) over incl. Radial Axial max. Radial or Axial Direction max.
Direction Direction Direction Direction
Ring
Side Face of Inner/
0.05 - - 0.1 0.2 0.05 0.15 - - 0.3 0.6 0.15 0.05 0.1 0.05
Central Washer
0.08 - - 0.16 0.3 0.08

Outer Ring or
0.1 - - 0.2 0.4 0.1 0.08 0.16 0.08

- 40 0.7 1.4
0.3 0.3
0.15 - - 0.3 0.6 0.15 40 - 0.9 1.6 0.1 0.2 0.1
0.2 - - 0.5 0.8 0.2
- 40 1.1 1.7
0.6 0.6 0.15 0.3 0.15
- 40 0.6 1 40 - 1.3 2
0.3 0.3
40 - 0.8 1 0.2 0.5 0.2
- 50 1.6 2.5
1 1 0.3 0.8 0.3
- 40 1 2 50 - 1.9 3
r : Chamfer Dimension of Inner/Outer Ring 0.6
40 - 1.3 2
0.6
r1 : Chamfer Dimension of Inner/Outer Ring (Front Side) - 120 2.3 3 0.6 1.5 0.6
or of Central Washer of Thrust Ball Bearings - 50 1.5 3
1 1 1.5 120 250 2.8 3.5 1.5
50 - 1.9 3 250 - 3.5 4 1 2.2 1
Remarks The precise shape of chamfer surfaces has not - 120 2 3.5 1.1 2.7 1
been specified but its profile in the axial plane shall 1.1 1 - 120 2.8 4
not intersect an arc of radius r (min.) or r1 (min.)
120 - 2.5 4 2 120 250 3.5 4.5 2
touching the side face of an inner ring or central washer and 250 - 4 5 1.5 3.5 1.5
bore surface, or the side face of an outer ring and outside
- 120 2.3 4
1.5 1.5
surface. 120 - 3 5
- 120 3.5 5
2 4 2
- 80 3 4.5 2.5 120 250 4 5.5 2 2.1 4.5 2

2 80 220 3.5 5 2 250 - 4.5 6
220 - 3.8 6 3 5.5 2.5
- 120 4 5.5
- 280 4 6.5 120 250 4.5 6.5 4 6.5 3
2.1 2 3 2.5
280 - 4.5 7 250 400 5 7
5 8 4
400 - 5.5 7.5
- 100 3.8 6
2.5 100 280 4.5 6 2 - 120 5 7 6 10 5
280 - 5 7 120 250 5.5 7.5
4 3 7.5 12.5 6
250 400 6 8
- 280 5 8
3
280 - 5.5 8
2.5 400 - 6.5 8.5 9.5 15 8
4 - - 6.5 9 3 - 180 6.5 8

5 4 12 18 10
5 - - 8 10 4 180 - 7.5 9
15 21 12
6 - - 10 13 5 - 180 7.5 10
6 5 19 25 15
7.5 - - 12.5 17 6 180 - 9 11
9.5 - - 15 19 8
Note (1) Inner Rings are classified by d and Outer Rings
12 - - 18 24 10 by D.
15 - - 21 30 12
19 - - 25 38 15
Remarks For bearings with nominal widths less than
2mm, the value of r (max.) in the axial
direction is the same as that in the radial
direction.
A 78 A 79
A058-081E.indd 78-79 11/20/13 4:51:15 PM

BEARING TOLERANCES
Table 8.10 Tolerances for Tapered Bores (Class Normal)
Nominal Tapered Bore Tapered Bore with Deviation in Single Plane

Taper 1 : 30
Mean Bore Diameter Units : m
& d 1mp jd mp
2
d & dmp & d 1 mp - & dmp Vdp (1) (2)
(mm)
over incl. high low high low max.
80 120 +20 0 +35 0 22
120 180 +25 0 +40 0 40
180 250 +30 0 +46 0 46
j(d1 + & d 1mp )

j(d + & dmp )
250 315 +35 0 +52 0 52
+40 +57
jd1
jd
315 400 0 0 57
400 500 +45 0 +63 0 63
500 630 +50 0 +70 0 70

Notes (1) Applicable to all radial planes of tapered bores.
(2) Not applicable to diameter series 7 and 8.
Remarks For a value exceeding 630 mm, please contact NSK.
B B
8.2 Selection of Accuracy Classes
For general applications, Class Normal tolerances are
d : Nominal Bore Diameter adequate in nearly all cases for satisfactory
d 1 : Theoretical Diameter of Larger End of Tapered Bore performance, but for the following applications,
Taper 1:12 d1 = d + 1/12 B Taper 1:30 d1 = d + /30 B bearings having an accuracy class of 5,4 or higher
& dmp : Single Plane Mean Bore Diameter Deviation in Theoretical Diameter of Smaller End of Bore
are more suitable.
& d1mp : Single Plane Mean Bore Diameter Deviation in Theoretical Diameter of Larger End of Bore
For reference, in Table 8.11, examples of applications
V d p : Bore diameter variation in a single radial plane and appropriate tolerance classes are listed for various
B : Nominal Inner Ring width bearing requirements and operating conditions.
: Half of Taper Angle of Tapered Bore
Taper 1:12 Taper 1:30
=2239.4 =5717.4 Table 8. 11 Typical Tolerance Classes for Specific Applications (Reference)
=2.38594 =0.95484 Bearing Requirement,
=0.041643 rad =0.016665 rad Operating Conditions Examples of Applications Tolerance Classes
VTR Drum Spindles P5

Taper 1 : 12
Units : m
Magnetic Disk Spindles for
Computers } P5, P4, P2
Machine-Tool Main Spindles P5, P4, P2
Nominal Bore Diameter High running accuracy Rotary Printing Presses P5
d & dmp & d 1 mp - & dmp Vdp (1) (2)
(mm)
is required Rotary Tables of Vertical
Presses, etc. } P5, P4
over
18
incl.
30
high
+33
low
0
high
+21
low
0
max.
13
Roll Necks of Cold Rolling
Mill Backup Rolls } Higher than P4
30
50
50
80
+39
+46
0
0
+25
+30
0
0
16
19
Slewing Bearings for Parabolic
Antennas } Higher than P4
80 120 +54 0 +35 0 22

Dental Drills CLASS 7P, CLASS 5P
120 180 +63 0 +40 0 40
180 250 +72 0 +46 0 46 Gyroscopes CLASS 7P, P4
250 315 +81 0 +52 0 52 Extra high speed is High Frequency Spindles CLASS 7P, P4
315 400 +89 0 +57 0 57
400 500 +97 0 +63 0 63 required Superchargers P5, P4
500 630 +110 0 +70 0 70 Centrifugal Separators P5, P4
630 800 +125 0 +80 0 - Main Shafts of Jet Engines Higher than P4
800 1 000 +140 0 +90 0 -
1 000 1 250 +165 0 +105 0 - Low torque and low Gyroscope Gimbals CLASS 7P, P4
1 250 1 600 +195 0 +125 0 -
torque variation are Servomechanisms CLASS 7P, CLASS 5P
Notes ( ) Applicable to all radial planes of tapered bores.
1
required
(2) Not applicable to diameter series 7 and 8. Potentiometric Controllers CLASS 7P
A 80 A 81
A058-081E.indd 80-81 11/20/13 4:51:16 PM

9. FITS AND INTERNAL CLEARANCES
9.1 Fits 9.1.2 Selection of Fit Therefore, the effective interference & d should be roughness of the surfaces and may be estimated using
9.1.1 Importance of Proper Fits (1) Load Conditions and Fit larger than the interference given by Equation (9.1). the following equations:
The proper fit may be selected from Table 9.1 based on However, in the case of heavy loads where the radial
In the case of a rolling bearing with the inner ring fitted load exceeds 20% of the basic static load rating C 0 r, d
to the shaft with only slight interference, a harmful the load and operating conditions. & d= & da . . . . . . . . . . . . (9.4)
under the operating condition, interference often For ground shafts d+2
circumferential slipping may occur between the inner becomes shortage. Therefore, interference should be
ring and shaft. This slipping of the inner ring, which is (2) Magnitude of Load and Interference d
estimated using Equation (9.2):
called creep, results in a circumferential displacement The interference of the inner ring is slightly reduced For machined shafts & d= d + 3 & da . . . . . . . . . . . . (9.5)
of the ring relative to the shaft if the interference by the bearing load; therefore, the loss of interference
fit is not sufficiently tight. When creep occurs, the should be estimated using the following equations: Fr 3
& d0.02 10 . . . . . . . . . . (N)
fitted surfaces become abraded, causing wear and B where & d : Effective interference (mm)
d
considerable damage to the shaft. Abnormal heating & dF =0.08
B r

F 10 3 . . . . . . . . (N)
Fr 3
. . . . . . . (9.2) & d a : Apparent interference (mm)
and vibration may also occur due to abrasive metallic & d0.2 10 . . . . . . . . . {kgf} d : Bearing nominal bore diameter (mm)
particles entering the interior of the bearing. . . . (9.1) B
d
It is important to prevent creep by having sufficient & dF =0.25 F 10 3 . . . . . {kgf} According to Equations (9.4) and (9.5), the effective
B r interference of bearings with a bore diameter of 30 to
interference to firmly secure that ring which rotates where & d : Effective interference (mm)
to either the shaft or housing. Creep cannot always 150 mm is about 95% of the apparent interference.
where & d F : Interference decrease of inner ring Fr : Radial load applied on bearing
be eliminated using only axial tightening through (N), {kgf}
the bearing ring faces. Generally, it is not necessary, (mm) (5) Fitting Stress and Ring Expansion and
d : Bearing bore diameter (mm) B : Nominal inner ring width (mm)
however, to provide interference for rings subjected Contraction
only to stationary loads. Fits are sometimes made B : Nominal inner ring width (mm) When bearings are mounted with interference on
Fr : Radial load applied on bearing (3) Interference Variation Caused by Temperature
without any interference for either the inner or outer a shaft or in a housing, the rings either expand or
(N), {kgf} Difference between Bearing and Shaft or
ring, to accommodate certain operating conditions, or contract and stress is produced. Excessive interference
Housing
to facilitate mounting and dismounting. In this case, may damage the bearings; therefore, as a general
The effective interference decreases due to the
to prevent damage to the fitting surfaces due to creep, guide, the maximum interference should be kept under
increasing bearing temperature during operation. If
lubrication of other applicable methods should be approximately 7/10 000 of the shaft diameter.
the temperature difference between the bearing and
considered. The pressure between fitted surfaces, expansion or
housing is & T (C), then the temperature difference
contraction of the rings, and circumferential stress
between the fitted surfaces of the shaft and inner ring
may be calculated using the equations in Section 15.2,
is estimated to be about (0.1~0.15) & T in case that
Fitting(1) (Pages A130 and A131).
the shaft is cooled. The decrease in the interference of
Table 9.1 Loading Conditions and Fits the inner ring due to this temperature difference & d T
9.1.3 Recommended Fits
may be calculated using Equation (9.3):
Load Application
Bearing Operation Load Fitting As described previously, many factors, such as
Inner Ring Outer Ring Conditions Inner Ring Outer Ring & d T = (0.10 to 0.15) & Td the characteristics and magnitude of bearing load,
H0.0015& Td 10 3 ...................(9.3) temperature differences, means of bearing mounting
and dismounting, must be considered when selecting
Rotating Stationary where & d T : Decrease in interference of inner ring the proper fit.
Rotating If the housing is thin or the bearing is mounted on a
Load Inner Ring due to temperature difference (mm)
Stationary Load & T : Temperature difference between bearing
hollow shaft, a tighter than usual fit is necessary. A
Tight Fit Loose Fit split housing often deforms the bearing into an oval
Load Rotating interior and surrounding parts (C)
Stationary shape; therefore, a split housing should be avoided
Outer Ring : Coefficient of linear expansion of when a tight fit with the outer ring is required.
Stationary Rotating Load bearing steel=12.510 6 (1/C) The fits of both the inner and outer rings should be
d : Bearing nominal bore diameter (mm) tight in applications where the shaft is subjected to
considerable vibration.
In addition, depending on the temperature difference The recommended fits for some common applications
between the outer ring and housing, or difference in are shown in Table 9.2 to 9.7. In the case of unusual
their coefficients of linear expansion, the interference operating conditions, it is advisable to consult NSK.
may increase. For the accuracy and surface finish of shafts and
Stationary Rotating Rotating housings, please refer to Section 11.1 (Page A100).
Outer Ring
Load (4) Effective Interference and Finish of Shaft and
Load Stationary Loose Fit Tight Fit Housing
Stationary Since the roughness of fitted surfaces is reduced
Inner Ring during fitting, the effective interference becomes
Load
less than the apparent interference. The amount of
Rotating Stationary
this interference decrease varies depending on the
Load
Rotating
Direction of load indeterminate due to Rotating or Rotating or Direction of Load

Tight Fit Tight Fit
variation of direction or unbalanced load Stationary Stationary Indeterminate
A 82 A 83
A082-099E.indd 82-83 11/20/13 4:51:45 PM

FITS AND INTERNAL CLEARANCES
Table 9.2 Fits of Radial Bearings with Shafts Table 9.4 Fits of Radial Bearings with Housings
Shaft Diameter (mm) Tolerances for Axial Displacement

Load Conditions Examples Remarks
Cylindrical Roller Spherical Roller Tolerance Housing Bores of Outer Ring
Load Conditions Examples Remarks
Ball Brgs Brgs, Tapered of Shaft Heavy Loads on Bearing in Automotive Wheel Hubs
Roller Brgs Brgs Thin-Walled Housing or (Roller Bearings) P7
Heavy Shock Loads Crane Travelling Wheels
Radial Bearings with Cylindrical Bores Rotating Normal or Heavy Automotive Wheel Hubs
(Ball Bearings) N7
Easy axial Wheels on Use g5 and h5 where Outer Ring Loads Vibrating Screens
displacement of Load Impossible
inner ring on shaft Stationary g6 accuracy is required. Conveyor Rollers
Rotating desirable. Axles Light or Variable
In case of large Solid Rope Sheaves
Outer All Shaft Diameters Loads M7
Easy axial bearings, f6 can be Housings Tension Pulleys
Ring Load displacement of Tension Pulleys
h6 used to allow easy axial
inner ring on shaft Rope Sheaves Heavy Shock Loads Traction Motors
unnecessary movement.
Electrical Home <18 js5 If axial displacement of
Normal or Heavy Pumps Generally
Light Loads Appliances Pumps, Direction of Loads K7 the outer ring is not
18 to 100 js6(j6) Crankshaft Main Impossible
or Variable Blowers, Transport <40 Load required.
Indeterminate Bearings
Loads Vehicles, Precision 100 to 200 40 to 140 k6 Medium and Large Axial displacement of
(<0.06Cr(1)) Machinery, Normal or Light
Machine Tools 140 to 200 m6 Motors(1) JS7 (J7) Possible outer ring is
Loads
necessary.
<18 js5 or js6 (j5 or j6)
General Bearing
General Bearing Solid or Loads of All kinds Applications, H7
18 to 100 <40 <40 k5 or k6 Split Railway Axleboxes
Applications, k6 and m6 can be
Medium and 100 to 140 40 to 100 40 to 65 m5 or m6 used for single-row Housings Normal or Light Easily
Rotating Inner Plummer Blocks H8
Large Motors(3), tapered roller Loads possible
Ring Load or 140 to 200 100 to 140 65 to 100 m6
Normal Loads Turbines, Pumps, bearings and single- Rotating High Temperature Rise
Direction of Paper Dryers G7
(0.06 to 0.13Cr(1)) Engine Main 200 to 280 140 to 200 100 to 140 n6 row angular contact Inner Ring of Inner Ring Through
Load Shaft
Bearings, ball bearings Load
Indeterminate 200 to 400 140 to 280 p6 Grinding Spindle Rear
Gears, instead of k5 and
Woodworking m5. Ball Bearings
280 to 500 r6 High Speed Centrifugal JS6 (J6) Possible
Machines
Accurate Running Compessor Free
over 500 r7 Bearings
Desirable under
Railway Axleboxes, 50 to 140 50 to 100 n6 Normal or Light Grinding Spindle Front
Industrial Vehicles, More than CN Direction of Loads Ball Bearings For heavy loads,
Heavy Loads 140 to 200 100 to 140 p6 Generally interference fit tighter
Traction Motors, bearing internal Load High Speed Centrifugal K6
or Shock Loads Compressor Fixed Impossible than K is used.
Construction over 200 140 to 200 r6 clearance is Indeterminate
(>0.13Cr(1)) Solid Housing Bearings When high accuracy is
Equipment, necessary.
Crushers 200 to 500 r7 required, very strict
Accurate Running and Cylindrical Roller
tolerances should be
High Rigidity Desirable Bearings for Machine M6 or N6 Impossible
Axial Loads Only All Shaft Diameters js6 (j6) used for fitting.
Rotating under Variable Loads Tool Main Spindle
Inner Ring
Radial Bearings with Tapered Bores and Sleeves Load Minimum noise is Electrical Home Easily
General bearing IT5 and IT7 mean that H6
required. Appliances Possible
Applications, h9/IT5(2) the deviation of the shaft
Railway Axleboxes from its true geometric
All Types of Loading All Shaft Diameters form, e. g. roundness and
Transmission Shafts, cylindricity should be Note (1) Refer to Tables 9.13.1 and 9.13.2 for the recommended fits of housing bores of deep groove ball bearings and
Woodworking h10/IT7(2) within the tolerances of cylindrical roller bearings for electric motors.
Spindles IT5 and IT7 respectively.
Remarks 1. This table is applicable to cast iron and steel housings. For housings made of light alloys, the interference should
Notes (1) Cr represents the basic load rating of the bearing. be tighter than those in this table.
(2) Refer to Appendix Table 11 on page C22 for the values of standard tolerance grades IT. 2. Refer to the introductory section of the bearing dimension tables (blue pages) for special fits such as drawn cup
(3) Refer to Tables 9.13.1 and 9.13.2 for the recommended fits of shafts used in electric motors for deep groove ball needle roller bearings.
bearings with bore diameters ranging from 10 mm to 160 mm, and for cylindrical roller bearings with bore diameters
ranging from 24 mm to 200 mm. Table 9.5 Fits of Thrust Bearings with Housings
Remarks This table is applicable only to solid steel shafts.
Tolerances for
Load Conditions Bearing Types Remarks
Table 9.3 Fits of Thrust Bearings with Shafts Housing Bores
Thrust Ball Clearance over 0.25mm For General Applications
Tolerance Bearings H8 When precision is required
Load Conditions Examples Shaft Diameter (mm) Remarks
of Shaft
Spherical Thrust
Axial Loads Only Roller Bearings
Main Shafts h6 or Outer ring has radial When radial loads are sustained by
Central Axial Load Only All Shaft Diameters Steep Angle
of Lathes js6 (j6) clearance. other bearings.
Tapered Roller
Stationary Inner Bearings
Combined Ring Load Cone Crushers All Shaft Diameters js6 (j6)
Radial and Combined
Axial Loads Rotating Inner Ring Paper Pulp <200 k6 Stationary Outer Ring Loads H7 or JS7 (J7)
Load or Direction Refiners, Radial Spherical Thrust
(Spherical 200 to 400 m6 and Axial Roller Bearings
of Load Plastic Rotating Outer Ring Loads or K7 Normal Loads
Thrust Roller Loads
Bearings) Indeterminate Extruders over 400 n6 Direction of Load Indeterminate M7 Relatively Heavy Radial Loads
A 84 A 85
A082-099E.indd 84-85 11/20/13 4:51:46 PM

Table 9.6 Fits of Inch Design Tapered Roller Bearings with Shafts Table 9.7 Fits of Inch Design Tapered Roller Bearings with Housings
(1) Bearings of Precision Classes 4 and 2 Units : m (1) Bearings of Precision Classes 4 and 2 Units : m
Bore Diameter Shaft Diameter Outside Diameter Housing Bore
Nominal Bore Diameters d Tolerances
Tolerances
Nominal Outside Diameters D Tolerances Diameter
& ds & Ds Tolerances
Operating Conditions Remarks Operating Conditions Remarks
over incl. over incl.
(mm) 1/25.4 (mm) 1/25.4 high low high low (mm) 1/25.4 (mm) 1/25.4 high low high low
76.200 3.0000 +13 0 + 38 + 25 76.200 3.0000 +25 0 + 76 + 51
Normal Loads
76.200 3.0000 304.800 12.0000 +25 0 + 64 + 38 For bearings with d152.4 mm, Used either 76.200 3.0000 127.000 5.0000 +25 0 + 76 + 51 The outer ring can be easily
Rotating Inner
304.800 12.0000 609.600 24.0000 +51 0 +127 + 76 clearance is usually larger than CN. on free-end or 127.000 5.0000 304.800 12.0000 +25 0 + 76 + 51 displaced axially.
Ring Loads
609.600 24.0000 914.400 36.0000 +76 0 +190 +114 fixed-end 304.800 12.0000 609.600 24.0000 +51 0 +152 +102
Rotating Inner Ring Loads

76.200 3.0000 +13 0 + 64 + 38 In general, bearings with a clear- 609.600 24.0000 914.400 36.0000 +76 0 +229 +152
Heavy Loads
Shock Loads
76.200 3.0000 304.800 12.0000 +25 0 g ance larger than CN are used. 76.200 3.0000 +25 0 + 25 0
High Speeds
304.800 12.0000 609.600 24.0000 +51 0 g g means that the average The outer ring 76.200 3.0000 127.000 5.0000 +25 0 + 25 0
The outer ring can be displaced
609.600 24.0000 914.400 36.0000 +76 0 +381 +305 interference is about 0.0005 d. position can be 127.000 5.0000 304.800 12.0000 +25 0 + 51 0 axially.
76.200 3.0000 +13 0 + 13 0 The inner ring cannot be displaced axially. adjusted axially. 304.800 12.0000 609.600 24.0000 +51 0 + 76 + 25
76.200 3.0000 304.800 12.0000 +25 0 + 25 0 When heavy or shock loads exist, the 609.600 24.0000 914.400 36.0000 +76 0 +127 + 51
Rotating Outer
304.800 12.0000 609.600 24.0000 +51 0 + 51 0 figures in the above (Rotating inner ring 76.200 3.0000 +25 0 13 38
Ring Loads
The outer ring 51

Normal Loads 609.600 24.0000 914.400 36.0000 +76 0 + 76 0 loads, heavy or shock loads) apply. 76.200 3.0000 127.000 5.0000 +25 0 25
position cannot Generally, the outer ring is fixed
without Shocks 76.200 3.0000 +13 0 0 13 127.000 5.0000 304.800 12.0000 +25 0 25 51
be adjusted axially.
76.200 3.0000 304.800 12.0000 +25 0 0 25 The inner ring can be displaced axially. 304.800 12.0000 609.600 24.0000 +51 0 25 76
304.800 12.0000 609.600 24.0000 +51 0 0 51 axially. 609.600 24.0000 914.400 36.0000 +76 0 25 102
76 38
Rotating Outer
609.600 24.0000 914.400 36.0000 +76 0 0 Normal Loads 76.200 3.0000 +25 0 13
+25 51
Ring Loads
The outer ring 76.200 3.0000 127.000 5.0000 0 25
position cannot 127.000 5.0000 304.800 12.0000 +25 0 25 51 The outer ring is fixed axially.
be adjusted 304.800 12.0000 609.600 24.0000 +51 0 25 76
axially. 609.600 24.0000 914.400 36.0000 +76 0 25 102
(2) Bearings of Precision Classes 3 and 0 (1) Units : m (2) Bearings of Precision Classes 3 and 0 (1) Units : m
Bore Diameter Outside Diameter Housing Bore
Shaft Diameter
Nominal Bore Diameters d Tolerances
Tolerances
Nominal Outside Diameters D Tolerances Diameter
& ds & Ds Tolerances
Operating Conditions Remarks Operating Conditions Remarks
over incl. over incl.
(mm) 1/25.4 (mm) 1/25.4 high low high low (mm) 1/25.4 (mm) 1/25.4 high low high low
76.200 3.0000 +13 0 + 30 +18 152.400 6.0000 +13 0 +38 +25
Precision
Machine-Tool
76.200 3.0000 304.800 12.0000 +13 0 + 30 +18
Used on free- 152.400 6.0000 304.800 12.0000 +13 0 +38 +25 The outer ring can be easily
Rotating Inner
Main Spindles
304.800 12.0000 609.600 24.0000 +25 0 + 64 +38 end 304.800 12.0000 609.600 24.0000 +25 0 +64 +38 displaced axially.
Ring Loads
609.600 24.0000 914.400 36.0000 +38 0 +102 +64 609.600 24.0000 914.400 36.0000 +38 0 +89 +51
Rotating Inner Ring Loads

76.200 3.0000 +13 0 152.400 6.0000 +13 0 +25 +13
Heavy Loads
Shock Loads
76.200 3.0000 304.800 12.0000 +13 0 A minimum interference of about Used on fixed- 152.400 6.0000 304.800 12.0000 +13 0 +25 +13 The outer ring can be displaced
304.800 12.0000 609.600 24.0000 +25 0 0.00025 d is used. end 304.800 12.0000 609.600 24.0000 +25 0 +51 +25 axially.
High Speeds
609.600 24.0000 914.400 36.0000 +38 0 609.600 24.0000 914.400 36.0000 +38 0 +76 +38

Rotating Outer
Precision
76.200 3.0000 +13 0 + 30 +18 The outer ring 152.400
152.400 6.0000 +13 0 +13 0
Ring Loads
Machine-Tool
76.200 3.0000 304.800 12.0000 +13 0 + 30 +18 position can be
6.0000 304.800 12.0000 +13 0 +25 0 Generally, the outer ring is fixed
Main Spindles
304.800 12.0000 609.600 24.0000 +25 0 + 64 +38 adjusted axially.
304.800 12.0000 609.600 24.0000 +25 0 +25 0 axially.
609.600 24.0000 914.400 36.0000 +38 0 +102 +64 609.600 24.0000 914.400 36.0000 +38 0 +38 0
Note (1) For bearings with d greater than 304.8 mm, Class 0 does not exist. The outer ring 152.400 6.0000 +13 0 0 13
position cannot 152.400 6.0000 304.800 12.0000 +13 0 0 25
The outer ring is fixed axially.
be adjusted 304.800 12.0000 609.600 24.0000 +25 0 0 25
axially. 609.600 24.0000 914.400 36.0000 +38 0 0 38
13 25
Rotating Outer
Normal Loads 76.200 3.0000 +13 0

+13 13 25
Ring Loads
The outer ring 76.200 3.0000 152.400 6.0000 0

position cannot 152.400 6.0000 304.800 12.0000 +13 0 13 38 The outer ring is fixed axially.
be adjusted 304.800 12.0000 609.600 24.0000 +25 0 13 38
axially. 609.600 24.0000 914.400 36.0000 +38 0 13 51
Note (1) For bearings with D greater than 304.8 mm, Class 0 does not exist.
A 86 A 87
A082-099E.indd 86-87 11/20/13 4:51:48 PM

9.2 Bearing Internal Clearances To obtain accurate measurements, the clearance is Table 9.9 Radial Internal Clearances in Table 9.10 Radial Internal Clearances in Extra
generally measured by applying a specified measuring Deep Groove Ball Bearings Small and Miniature Ball Bearings
9.2.1 Internal Clearances and Their Standards
load on the bearing; therefore, the measured clearance Units : m Units : m
The internal clearance in rolling bearings in operation (sometimes called measured clearance to make a
greatly influences bearing performance including Clear-
distinction) is always slightly larger than the theoretical Nominal Bore Clearance ance MC1 MC2 MC3 MC4 MC5 MC6
fatigue life, vibration, noise, heat-generation, etc. internal clearance (called geometrical clearance for Diameter Symbol
Consequently, the selection of the proper internal radial bearings) by the amount of elastic deformation d (mm) C2 CN C3 C4 C5 min. max. min. max. min. max. min. max. min. max. min. max.
clearance is one of the most important tasks when caused by the measuring load. Clear-
choosing a bearing after the type and size have been Therefore, the theoretical internal clearance may be over incl. min. max. min. max. min. max. min. max. min. max. ance 0 5 3 8 5 10 8 13 13 20 20 28
determined. obtained by correcting the measured clearance by the
This bearing internal clearance is the combined amount of elastic deformation. However, in the case 10 only 0 7 2 13 8 23 14 29 20 37
10 18 0 9 3 18 11 25 18 33 25 45 Remarks 1. The standard clearance is MC3.
clearances between the inner/outer rings and rolling of roller bearings this elastic deformation is negligibly Remarks 2. To obtain the measured value, add
18 24 0 10 5 20 13 28 20 36 28 48
elements. The radial and axial clearances are defined small. correction amount in the table below.
as the total amount that one ring can be displaced Usually the clearance before mounting is the one 24 30 1 11 5 20 13 28 23 41 30 53
relative to the other in the radial and axial directions specified as the theoretical internal clearance. 30 40 1 11 6 20 15 33 28 46 40 64
respectively (Fig. 9.1). 40 50 1 11 6 23 18 36 30 51 45 73 Units : m
In Table 9.8, reference table and page numbers are
listed by bearing types. 50 65 1 15 8 28 23 43 38 61 55 90 Clearance
MC1 MC2 MC3 MC4 MC5 MC6
65 80 1 15 10 30 25 51 46 71 65 105 Symbol
80 100 1 18 12 36 30 58 53 84 75 120
Clearance
Correction 1 1 1 1 2 2
100 120 2 20 15 41 36 66 61 97 90 140
Value
120 140 2 23 18 48 41 81 71 114 105 160
Table 9.8 Index for Radial Internal Clearances 140 160 2 23 18 53 46 91 81 130 120 180 The measuring loads are as
follows :
by Bearing Types 160 180 2 25 20 61 53 102 91 147 135 200 For miniature ball bearings*
Table Page 180 200 2 30 25 71 63 117 107 163 150 230 2.5N {0.25kgf}
Bearing Types 200 225 2 35 25 85 75 140 125 195 175 265 For extra small ball bearings*
Number Number
4.4N {0.45kgf}
Deep Groove Ball Bearings 9.9 A89 225 250 2 40 30 95 85 160 145 225 205 300
250 280 2 45 35 105 90 170 155 245 225 340 *For their classification, refer to
280 315 2 55 40 115 100 190 175 270 245 370 Table 1 on Page B 31.
Extra Small and Miniature Ball Bearings 9.10 A89
315 355 3 60 45 125 110 210 195 300 275 410
Magneto Bearings 9.11 A89 355 400 3 70 55 145 130 240 225 340 315 460
400 450 3 80 60 170 150 270 250 380 350 510 Table 9.11 Radial Internal Clearances in
Magneto Bearings
Self-Aligning Ball Bearings 9.12 A90 Units : m
450 500 3 90 70 190 170 300 280 420 390 570
Deep Groove 500 560 10 100 80 210 190 330 310 470 440 630 Nominal Bore
9.13.1 A90 560 630 10 110 90 230 210 360 340 520 490 690 Diameter Clearance
Ball Bearings Bearing
For Motors d (mm)
Cylindrical 630 710 20 130 110 260 240 400 380 570 540 760 Series
Radial Clearance Axial Clearance 9.13.2 A90 over incl. min. max.
Roller Bearings 710 800 20 140 120 290 270 450 430 630 600 840
With Cylindrical Bores EN 10 50
Remarks To obtain the measured values, use the clearance correction for 2.5 30
Table 9.8 Bearing Internal Clearance Cylindrical
With Cylindrical Bores radial clearance increase caused by the measuring load in the E 30 60
(Matched) 9.14 A91 table below.
Roller Bearings
With Tapered Bores Remarks For the C2 clearance class, the smaller value should be used
(Matched) for bearings with minimum clearance and the larger value for
bearings near the maximum clearance range.
Spherical With Cylindrical Bores
9.15 A92
Roller Bearings With Tapered Bores Units : m
Nominal Bore Radial Clearance Correction
Double-Row and Combined Tapered Measuring
9.15 A93 Dia. d (mm) Amount
Roller Bearings Load
Combined Angular Contact Ball over incl. (N) {kgf} C2 CN C3 C4 C5
9.17 A94
Bearings (1)
10 (incl) 18 24.5 {2.5} 3 to 4 4 4 4 4
Four-Point Contact Ball Bearings (1) 9.18 A94 18 50 49 {5} 4 to 5 5 6 6 6
50 280 147 {15} 6 to 8 8 9 9 9
Note (1) Values given are axial clearances.
Remarks For values exceeding 280 mm, please contact NSK.
A 88 A 89
A082-099E.indd 88-89 11/20/13 4:51:49 PM

Table 9.12 Radial Internal Clearances in Table 9.14 Radial Internal Clearances in Cylindrical
Self-Aligning Ball Bearings Roller Bearings and Solid-Type Needle Roller Bearings
Units : m Units : m
Nominal Bore Clearance in Bearings with Cylindrical Bores Clearance in Bearings with Tapered Bores Nominal Clearances in Bearings Clearances in Non-Interchangeable Bearings
Dia. d (mm) Bore Dia. with Cylindrical Bores with Cylindrical Bores
C2 CN C3 C4 C5 C2 CN C3 C4 C5
d (mm) C2 CN C3 C4 C5 CC1 CC2 CC (1) CC3 CC4 CC5
over incl. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.
over incl. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.
2.5 6 1 8 5 15 10 20 15 25 21 33
6 10 2 9 6 17 12 25 19 33 27 42 10 0 25 20 45 35 60 50 75
10 14 2 10 6 19 13 26 21 35 30 48 10 24 0 25 20 45 35 60 50 75 65 90 5 15 10 20 20 30 35 45 45 55 65 75
24 30 0 25 20 45 35 60 50 75 70 95 5 15 10 25 25 35 40 50 50 60 70 80
14 18 3 12 8 21 15 28 23 37 32 50
18 24 4 14 10 23 17 30 25 39 34 52 7 17 13 26 20 33 28 42 37 55 30 40 5 30 25 50 45 70 60 85 80 105 5 15 12 25 25 40 45 55 55 70 80 95
24 30 5 16 11 24 19 35 29 46 40 58 9 20 15 28 23 39 33 50 44 62 40 50 5 35 30 60 50 80 70 100 95 125 5 18 15 30 30 45 50 65 65 80 95 110
50 65 10 40 40 70 60 90 80 110 110 140 5 20 15 35 35 50 55 75 75 90 110 130
30 40 6 18 13 29 23 40 34 53 46 66 12 24 19 35 29 46 40 59 52 72
40 50 6 19 14 31 25 44 37 57 50 71 14 27 22 39 33 52 45 65 58 79 65 80 10 45 40 75 65 100 90 125 130 165 10 25 20 40 40 60 70 90 90 110 130 150
50 65 7 21 16 36 30 50 45 69 62 88 18 32 27 47 41 61 56 80 73 99 80 100 15 50 50 85 75 110 105 140 155 190 10 30 25 45 45 70 80 105 105 125 155 180
100 120 15 55 50 90 85 125 125 165 180 220 10 30 25 50 50 80 95 120 120 145 180 205
65 80 8 24 18 40 35 60 54 83 76 108 23 39 35 57 50 75 69 98 91 123
80 100 9 27 22 48 42 70 64 96 89 124 29 47 42 68 62 90 84 116 109 144 120 140 15 60 60 105 100 145 145 190 200 245 10 35 30 60 60 90 105 135 135 160 200 230
100 120 10 31 25 56 50 83 75 114 105 145 35 56 50 81 75 108 100 139 130 170 140 160 20 70 70 120 115 165 165 215 225 275 10 35 35 65 65 100 115 150 150 180 225 260
160 180 25 75 75 125 120 170 170 220 250 300 10 40 35 75 75 110 125 165 165 200 250 285
120 140 10 38 30 68 60 100 90 135 125 175 40 68 60 98 90 130 120 165 155 205
140 160 15 44 35 80 70 120 110 161 150 210 45 74 65 110 100 150 140 191 180 240 180 200 35 90 90 145 140 195 195 250 275 330 15 45 40 80 80 120 140 180 180 220 275 315
200 225 45 105 105 165 160 220 220 280 305 365 15 50 45 90 90 135 155 200 200 240 305 350
225 250 45 110 110 175 170 235 235 300 330 395 15 50 50 100 100 150 170 215 215 265 330 380
250 280 55 125 125 195 190 260 260 330 370 440 20 55 55 110 110 165 185 240 240 295 370 420
280 315 55 130 130 205 200 275 275 350 410 485 20 60 60 120 120 180 205 265 265 325 410 470
Table 9.13 Radial Internal Clearances in 315 355 65 145 145 225 225 305 305 385 455 535 20 65 65 135 135 200 225 295 295 360 455 520
Bearings for Electric Motors
355 400 100 190 190 280 280 370 370 460 510 600 25 75 75 150 150 225 255 330 330 405 510 585
Table 9.13. 1 Deep Groove Ball Bearings Table 9.13.2 Cylindrical Roller Bearings 400 450 110 210 210 310 310 410 410 510 565 665 25 85 85 170 170 255 285 370 370 455 565 650
for Electric Motors for Electric Motors 450 500 110 220 220 330 330 440 440 550 625 735 25 95 95 190 190 285 315 410 410 505 625 720
Units : m Units : m
Note (1) CC denotes normal clearance for non-Interchangeable cylindrical roller bearings and solid-type needle roller bearings.
Nominal Bore Clearance Remarks Nominal Bore Clearance Remarks
Dia. d (mm) CM Recommended fit Dia. d (mm) Interchangeable CT Non-Interchangeable CM Recommended Fit
over incl. min. max. Shaft Housing Bore over incl. min. max. min. max. Shaft Housing Bore
Units : m
10 (incl) 18 4 11 js5 (j5) 24 40 15 35 15 30 k5
Nominal Clearances in Non-Interchangeable Bearings with Tapered Bores
18 30 5 12 40 50 20 40 20 35 Bore Dia.
d (mm) CC9 (1) CC0 CC1 CC2 CC (2) CC3 CC4 CC5
30 50 9 17 50 65 25 45 25 40 over incl. min. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max.
H6, H7(1)
k5 10 24 5 10 10 20 20 30 35 45 45 55 55 65 75 85
or
50 80 12 22 65 80 30 50 30 45 24 30 5 10 8 15 10 25 25 35 40 50 50 60 60 70 80 95
JS6, JS7 30 40 5 12 8 15 12 25 25 40 45 55 55 70 70 80 95 110
80 100 18 30 JS6, JS7
(J6, J7)(2) 80 100 35 60 35 55 m5
(J6, J7)(1) 40 50 5 15 10 20 15 30 30 45 50 65 65 80 80 95 110 125
100 120 35 65 35 60 50 65 5 15 10 20 15 35 35 50 55 75 75 90 90 110 130 150
or 65 80 10 20 15 30 20 40 40 60 70 90 90 110 110 130 150 170
100 120 18 30
m5 K6, K7(2)
80 100 10 25 20 35 25 45 45 70 80 105 105 125 125 150 180 205
120 160 24 38 120 140 40 70 40 65 100 120 10 25 20 35 25 50 50 80 95 120 120 145 145 170 205 230
120 140 15 30 25 40 30 60 60 90 105 135 135 160 160 190 230 260
Notes (1) Applicable to outer rings that require movement in 140 160 50 85 50 80
the axial direction. 140 160 15 35 30 50 35 65 65 100 115 150 150 180 180 215 260 295
(2) Applicable to outer rings that do not require 160 180 15 35 30 50 35 75 75 110 125 165 165 200 200 240 285 320
160 180 60 95 60 90 180 200 20 40 30 50 40 80 80 120 140 180 180 220 220 260 315 355
movement in the axial direction. n6
Remarks The radial clearance increase caused by the 200 225 20 45 35 60 45 90 90 135 155 200 200 240 240 285 350 395
180 200 65 105 65 100 225 250 25 50 40 65 50 100 100 150 170 215 215 265 265 315 380 430
measuring load is equal to the correction amount
250 280 25 55 40 70 55 110 110 165 185 240 240 295 295 350 420 475
for CN clearance in the remarks under Table 9.9. Notes (1) Applicable to outer rings that require movement in
the axial direction. 280 315 30 60 60 120 120 180 205 265 265 325 325 385 470 530
(2) Applicable to outer rings that do not require 315 355 30 65 65 135 135 200 225 295 295 360 360 430 520 585
355 400 35 75 75 150 150 225 255 330 330 405 405 480 585 660
movement in the axial direction.
400 450 40 85 85 170 170 255 285 370 370 455 455 540 650 735
450 500 45 95 95 190 190 285 315 410 410 505 505 600 720 815
Notes (1) Clearance CC9 is applicable to cylindrical roller bearings with tapered bores in ISO Tolerance Classes 5 and 4.
Notes (2) CC denotes normal clearance for non-Interchangeable cylindrical roller bearings and solid-type needle roller
bearings.
A 90 A 91
A082-099E.indd 90-91 11/20/13 4:51:50 PM

Table 9.15 Radial Internal Clearances in Table 9.16 Radial Internal Clearances in Double-Row and
Spherical Roller Bearings Combined Tapered Roller Bearings
Units : m Units : m
Nominal Clearance in Bearings with Cylindrical Bores Clearance in Bearings with Tapered Bores Cylindrical Clearance
Bore Dia. Bore
d (mm) C2 CN C3 C4 C5 C2 CN C3 C4 C5 Tapered Bore C1 C2 CN C3 C4 C5
Nominal Bore
over incl. min.max. min.max. min. max. min. max. min. max. min.max. min. max. min. max. min. max. min. max. C1 C2 CN C3 C4
Dia. d (mm)
24 30 15 25 25 40 40 55 55 75 75 95 20 30 30 40 40 55 55 75 75 95 over incl. min. max. min. max. min. max. min. max. min. max. min. max.
30 40 15 30 30 45 45 60 60 80 80 100 25 35 35 50 50 65 65 85 85 105
40 50 20 35 35 55 55 75 75 100 100 125 30 45 45 60 60 80 80 100 100 130 18 0 10 10 20 20 30 35 45 50 60 65 75
18 24 0 10 10 20 20 30 35 45 50 60 65 75
24 30 0 10 10 20 20 30 40 50 50 60 70 80
50 65 20 40 40 65 65 90 90 120 120 150 40 55 55 75 75 95 95 120 120 160
65 80 30 50 50 80 80 110 110 145 145 180 50 70 70 95 95 120 120 150 150 200
80 100 35 60 60 100 100 135 135 180 180 225 55 80 80 110 110 140 140 180 180 230 30 40 0 12 12 25 25 40 45 60 60 75 80 95
40 50 0 15 15 30 30 45 50 65 65 80 95 110
50 65 0 15 15 35 35 55 60 80 80 100 110 130
100 120 40 75 75 120 120 160 160 210 210 260 65 100 100 135 135 170 170 220 220 280
120 140 50 95 95 145 145 190 190 240 240 300 80 120 120 160 160 200 200 260 260 330
140 160 60 110 110 170 170 220 220 280 280 350 90 130 130 180 180 230 230 300 300 380 65 80 0 20 20 40 40 60 70 90 90 110 130 150
80 100 0 25 25 50 50 75 80 105 105 130 155 180
100 120 5 30 30 55 55 80 90 115 120 145 180 210
160 180 65 120 120 180 180 240 240 310 310 390 100 140 140 200 200 260 260 340 340 430
180 200 70 130 130 200 200 260 260 340 340 430 110 160 160 220 220 290 290 370 370 470
200 225 80 140 140 220 220 290 290 380 380 470 120 180 180 250 250 320 320 410 410 520 120 140 5 35 35 65 65 95 100 130 135 165 200 230
140 160 10 40 40 70 70 100 110 140 150 180 220 260
160 180 10 45 45 80 80 115 125 160 165 200 250 290
225 250 90 150 150 240 240 320 320 420 420 520 140 200 200 270 270 350 350 450 450 570
250 280 100 170 170 260 260 350 350 460 460 570 150 220 220 300 300 390 390 490 490 620
280 315 110 190 190 280 280 370 370 500 500 630 170 240 240 330 330 430 430 540 540 680 180 200 10 50 50 90 90 130 140 180 180 220 280 320
200 225 20 60 60 100 100 140 150 190 200 240 300 340
225 250 20 65 65 110 110 155 165 210 220 270 330 380
315 355 120 200 200 310 310 410 410 550 550 690 190 270 270 360 360 470 470 590 590 740
355 400 130 220 220 340 340 450 450 600 600 750 210 300 300 400 400 520 520 650 650 820
400 450 140 240 240 370 370 500 500 660 660 820 230 330 330 440 440 570 570 720 720 910 250 280 20 70 70 120 120 170 180 230 240 290 370 420
280 315 30 80 80 130 130 180 190 240 260 310 410 460
315 355 30 80 80 130 140 190 210 260 290 350 450 510
450 500 140 260 260 410 410 550 550 720 720 900 260 370 370 490 490 630 630 790 790 1 000
500 560 150 280 280 440 440 600 600 780 780 1 000 290 410 410 540 540 680 680 870 870 1 100
560 630 170 310 310 480 480 650 650 850 850 1 100 320 460 460 600 600 760 760 980 980 1 230 355 400 40 90 90 140 150 200 220 280 330 390 510 570
400 450 45 95 95 145 170 220 250 310 370 430 560 620
450 500 50 100 100 150 190 240 280 340 410 470 620 680
630 710 190 350 350 530 530 700 700 920 920 1 190 350 510 510 670 670 850 850 1 090 1 090 1 360
710 800 210 390 390 580 580 770 770 1 010 1 010 1 300 390 570 570 750 750 960 960 1 220 1 220 1 500
800 900 230 430 430 650 650 860 860 1 120 1 120 1 440 440 640 640 840 840 1 070 1 070 1 370 1 370 1 690 500 560 60 110 110 160 210 260 310 380 450 520 700 770
560 630 70 120 120 170 230 290 350 420 500 570 780 850
630 710 80 130 130 180 260 310 390 470 560 640 870 950
900 1 000 260 480 480 710 710 930 930 1 220 1 220 1 570 490 710 710 930 930 1 190 1 190 1 520 1 520 1 860
1 000 1 120 290 530 530 780 780 1 020 1 020 1 330 530 770 770 1 030 1 030 1 300 1 300 1 670
1 120 1 250 320 580 580 860 860 1 120 1 120 1 460 570 830 830 1 120 1 120 1 420 1 420 1 830 710 800 90 140 150 200 290 340 430 510 630 710 980 1 060
1 250 1 400 350 640 640 950 950 1 240 1 240 1 620 620 910 910 1 230 1 230 1 560 1 560 2 000 800 900 100 150 160 210 320 370 480 570 700 790 1 100 1 200
900 1 000 120 170 180 230 360 410 540 630 780 870 1 200 1 300
1 000 1 120 130 190 200 260 400 460 600 700
1 120 1 250 150 210 220 280 450 510 670 770
1 250 1 400 170 240 250 320 500 570 750 870
1.5
Remarks Axial internal clearance & a = & r cot H e & r
Remarks where & r : Radial internal clearance
: Contact angle
e : Constant (Listed in bearing tables)
A 92 A 93
A082-099E.indd 92-93 11/20/13 4:51:51 PM

Table 9.17 Axial Internal Clearances in Combined Angular Contact (2) Decrease in Radial Internal Clearance Caused
Ball Bearings (Measured Clearance) by Temperature Differences between Inner and
Units : m
Outer Rings and Effective Clearance & : Effective Clearance
Axial Internal Clearance
Nominal Bore The frictional heat generated during operation &= &f t
Diameter. Contact Angle 30 Contact Angle 40 is conducted away through the shaft and housing. fe : Decrease in clearance due
d (mm) Since housings generally conduct heat better than
Outer ring to fit between outer ring
CN C3 C4 CN C3 C4 and housing bore
over incl. min. max. min. max. min. max. min. max. min. max. min. max.
shafts, the temperature of the inner ring and the rolling (=&De)
elements is usually higher than that of the outer ring &
10 9 29 29 49 49 69 6 26 26 46 46 66 &f & &
by 5 to 10C. If the shaft is heated or the housing 0 0 : Theoretical internal
10 18 10 30 30 50 50 70 7 27 27 47 47 67
18 24 19 39 39 59 59 79 13 33 33 53 53 73
is cooled, the difference in temperature between the clearance
inner and outer rings is greater. The radial clearance (Geometrical
24 30 20 40 40 60 60 80 14 34 34 54 54 74 clearance)
30 40 26 46 46 66 66 86 19 39 39 59 59 79
decreases due to the thermal expansion caused by the
Roller
40 50 29 49 49 69 69 89 21 41 41 61 61 81 temperature difference between the inner and outer & f :Residual clearance
rings. The amount of this decrease can be calculated & f = & 0 fi fe
50 65 35 60 60 85 85 110 25 50 50 75 75 100
65 80 38 63 63 88 88 115 27 52 52 77 77 100
using the following equations: fi : Decrease in clearance
80 100 49 74 74 99 99 125 35 60 60 85 85 110 due to fit between
100 120 72 97 97 120 120 145 52 77 77 100 100 125
tH & t De..................................... (9.6) inner ring and shaft (=&Di )
120 140 85 115 115 145 145 175 63 93 93 125 125 155 t : Decrease in clearance due
140 160 90 120 120 150 150 180 66 96 96 125 125 155 where t : Decrease in radial clearance due to to temperature difference
between inner and outer rings
160 180 95 125 125 155 155 185 68 98 98 130 130 160
temperature difference between inner and
180 200 110 140 140 170 170 200 80 110 110 140 140 170 outer rings (mm)
: Coefficient of linear expansion of bearing
Remarks This table is applicable to bearings in Tolerance Classes Normal and 6. For internal axial clearances in bearings in steelH12.5 106 (1/C)
tolerance classes better than 5 and contact angles of 15 and 25, it is advisable to consult NSK.
& t : Temperature difference between inner and
outer rings (C)
Table 9.18 Axial Internal Clearance in Four-Point Standard operating conditions are defined as those De : Outer ring raceway diameter (mm)
Contact Ball Bearings where the inner ring speed is less than approximately
(Measured Clearances) 50% of the limiting speed listed in the bearing tables, For ball bearings Fig. 9.2 Changes in Radial Internal Clearance of Bearings
Units : m the load is less than normal (PH 0.1C r), and the
Axial Internal Clearance
bearing is tight-fitted on the shaft. DeH 1 (4D + d) ..................... (9.7)
Nominal Bore As a measure to reduce bearing noise for electric 5
Dia. d (mm) C2 CN C3 C4 motors, the radial clearance range is narrower than For roller bearings Table 9. 19 Examples of Clearances for Specific
over incl. min. max. min. max. min. max. min. max. the normal class and the values are somewhat smaller
Applications
10 18 15 55 45 85 75 125 115 165 for deep groove ball bearings and cylindrical roller DeH 1 (3D + d) ..................... (9.8)
bearings for electric motors. (Refer to Table 9.13.1 and 4
18 40 26 66 56 106 96 146 136 186 Internal
40 60 36 86 76 126 116 166 156 206 9.13.2) The clearance after substracting this t from the Operating Conditions Examples
Clearance
Internal clearance varies with the fit and temperature residual clearance, & f is called the effective clearance,
60 80 46 96 86 136 126 176 166 226 differences in operation. The changes in radial When shaft deflection Semi-floating rear
& . Theoretically, the longest life of a bearing can is large. wheels of automobiles C5 or equivalent
80 100 56 106 96 156 136 196 186 246
100 140 66 126 116 176 156 216 206 266 clearance in a roller bearing are shown in Fig. 9.2. be expected when the effective clearance is slightly
negative. However, it is difficult to achieve such an Dryers in paper making
C3, C4
When steam passes machines
140 180 76 156 136 196 176 246 226 296 (1) Decrease in Radial Clearance Caused by Fitting ideal condition, and an excessive negative clearance through hollow shafts or
180 220 96 176 156 226 206 276 256 326 and Residual Clearance will greatly shorten the bearing life. Therefore, a roller shafts are heated. Table rollers for rolling C3
220 260 115 196 175 245 225 305 285 365 mills
When the inner ring or the outer ring is tight-fitted on clearance of zero or a slightly positive amount, instead
260 300 135 215 195 275 255 335 315 395 a shaft or in a housing, a decrease in the radial internal of a negative one, should be selected. When single-row Traction motors for C4
300 350 155 235 215 305 275 365 345 425 clearance is caused by the expansion or contraction angular contact ball bearings or tapered roller bearings When impact loads and railways
350 400 175 265 245 335 315 405 385 475
of the bearing rings. The decrease varies according to are used facing each other, there should be a small vibration are severe or Vibrating screens C3, C4
400 500 205 305 285 385 355 455 435 525 effective clearance, unless a preload is required. When when both the inner and
the bearing type and size and design of the shaft and outer rings are tight- Fluid couplings C4
housing. The amount of this decrease is approximately two cylindrical roller bearings with a rib on one side fitted.
Final reduction gears for
9.2.2 Selection of Bearing Internal Clearances 70 to 90% of the interference (refer to Section 15.2, are used facing each other, it is necessary to provide tractors C4
Fits (1), Pages A130 to A133). The internal clearance adequate axial clearance to allow for shaft elongation
Among the bearing internal clearances listed in the during operation. When both the inner and
tables, the CN Clearance is adequate for standard after subtracting this decrease from the theoretical outer rings are loose- Rolling mill roll necks C2 or equivalent
internal clearance & 0 is called the residual clearance, The radial clearances used in some specific fitted
operating conditions. The clearance becomes applications are given in Table9.19. Under special
progressively smaller from C2 to C1 and larger from & f. When noise and vibration Small motors with
operating conditions, it is advisable to consult NSK. restrictions are severe special specifications C1, C2, CM
C3 to C5.
When clearance is
adjusted after mounting
to prevent shaft Main shafts of lathes CC9, CC1
deflection, etc.
A 94 A 95
A082-099E.indd 94-95 11/20/13 4:51:52 PM

10. PRELOAD
Rolling bearings usually retain some internal clearance 10.2.2 Constant-Pressure Preload 10.3.2 Constant-Pressure Preload and Rigidity In the case of a constant-pressure preload, it
while in operation. In some cases, however, it is A constant pressure preload is achieved using a coil A preload diagram for duplex bearings under a is possible to minimize any change in the preload
desirable to provide a negative clearance to keep or leaf spring to impose a constant preload. Even if constant-pressure preload is shown in Fig. 10.5. The because the variation of the spring load with shaft
them internally stressed. This is called preloading . the relative position of the bearings changes during deflection curve of the spring is nearly parallel to the expansion and contraction is negligible. From the
A preload is usually applied to bearings in which the operation, the magnitude of the preload remains horizontal axis because the rigidity of springs is lower foregoing explanation, it is seen that position preloads
clearance can be adjusted during mounting, such as relatively constant (refer to Fig. 10.2) than that of the bearing. As a result, the rigidity under are generally preferred for increasing rigidity and
angular contact ball bearings or tapered roller bearings. a constant-pressure preload is approximately equal to constant-pressure preloads are more suitable for high
Usually, two bearings are mounted face-to-face or that for a single bearing with a preload Fa 0 applied speed applications, for prevention of axial vibration, for
back-to-back to form a duplex set with a preload. to it. Fig. 10.6 presents a comparison of the rigidity use with thrust bearings on horizontal shafts, etc.
of a bearing with a position preload and one with a
10.1 Purpose of Preload constant-pressure preload.
The main purposes and some typical applications of
preloaded bearings are as follows: 10.4 Selection of Preloading Method and
Amount of Preload
(1) To maintain the bearings in exact position both Fig. 10.1 Position Preload
10.4.1 Comparison of Preloading Methods
radially and axially and to maintain the running
accuracy of the shaft. A comparison of the rigidity using both preloading
...Main shafts of machine tools, precision methods is shown in Fig. 10.6. The position preload
instruments, etc. and constant-pressure preload may be compared as
(2) To increase bearing rigidity follows: Bearing A
a
Axial Load
...Main shafts of machine tools, pinion shafts of
final drive gears of automobiles, etc. (1) When both of the preloads are equal, the position
(3) To minimize noise due to axial vibration and preload provides greater bearing rigidity, in other
resonance Fig. 10.2 Constant-Pressure Preload words, the deflection due to external loads is less
...Small electric motors, etc. for bearings with a position preload. Fa
(4) To prevent sliding between the rolling elements and (2) In the case of a position preload, the preload
raceways due to gyroscopic moments 10.3 Preload and Rigidity varies depending on such factors as a difference
...High speed or high acceleration applications in axial expansion due to a temperature difference
10.3.1 Position Preload and Rigidity
of angular contact ball bearings, and thrust ball between the shaft and housing, a difference in Fa0
bearings When the inner rings of the duplex bearings shown radial expansion due to a temperature difference
(5) To maintain the rolling elements in their proper in Fig.10.3 are fixed axially, bearings A and B are between the inner and outer rings, deflection due to Axial Displacement
position with the bearing rings displaced a 0 and axial space 2 a 0 between the inner load, etc. a0
...Thrust ball bearings and spherical thrust roller rings is eliminated. With this condition, a preload Fa 0 is
aA
bearings mounted on a horizontal shaft imposed on each bearing. A preload diagram showing
bearing rigidity, that is the relation between load and Fig. 10.5 Axial Displacement with Constant-Pressure Preload
10.2 Preloading Methods displacement with a given axial load Fa imposed on a
Axial Load
duplex set, is shown in Fig. 10.4.
10.2.1 Position Preload Bearing B Bearing A
a
A position preload is achieved by fixing two axially
opposed bearings in such a way that a preload is
load
imposed on them. Their position, once fixed, remain Bearing Bearing
ad
relo
Pre
ad
unchanged while in operation. A B
Prelo
Pos ing with
tP
ure
In practice, the following three methods are generally Fa
hou
Fa Fa0 Fa0
Bea -Press
used to obtain a position preload. FaA
stan th
ition
wit
Con ing wi
r
Fa0
Bea
ring
t
Axial Load
(1) By installing a duplex bearing set with previously FaB
r
Bea
adjusted stand-out dimensions (see Page A7, Fig. a0 a0 a
1.1) and axial clearance. Axial Displacement
aA aB
(2) By using a spacer or shim of proper size to obtain Fig. 10.3 Back-to-Back Duplex Bearing Preload a
a0 a0
the required spacing and preload. (Refer to Fig.
a : Displacement of duplex Fa
10.1) Fa : Axial load applied from outside
(3) By utilizing bolts or nuts to allow adjustment of Fa A: Axial load imposed on Bearing A bearing set a
the axial preload. In this case, the starting torque FaB: Axial load imposed on Bearing B a A : Displacement of Bearing A
aB : Displacement of Bearing B Axial Displacement
should be measured to verify the proper preload.
Fig. 10.4 Axial Displacement with Position Preload Fig. 10.6 Comparison of Rigidities and Preloading Methods
A 96 A 97
A082-099E.indd 96-97 11/20/13 4:51:53 PM

PRELOAD
10.4.2 Amount of Preload (2) Preload of Thrust Ball Bearings (3) Preload of Spherical Thrust Roller Bearings
If the preload is larger than necessary, abnormal heart When the balls in thrust ball bearings rotate at relatively When spherical thrust roller bearings are used, damage
generation, increased frictional torque, reduced fatigue Table 10. 1 Recommended Fitting for
high speeds, sliding due to gyroscopic moments on the such as scoring may occur due to sliding between the
life, etc. may occur. The amount of the preload should High Accuracy Duplex
balls may occur. The larger of the two values obtained rollers and outer ring raceway. The minimum axial load
be carefully determined considering the operating Angular Contact Ball
from Equations(10.1) and (10.2) below should be Fa min necessary to prevent such sliding is obtained
conditions and the purpose of the preload. Bearings with Preload
adopted as the minimum axial load in order to prevent from the following equation:
such sliding
(1) Preloading of Duplex Angular Contact Ball Units : m
C 0a
Bearings Nominal Outside Fa min = ................................(10.3)
Nominal Bore C 0a n 2 1000
Average preloads for duplex angular contact ball Dia. d (mm) Target Shaft Dia.
D (mm)
Target
Housing
Fa min =
100
( Nmax ) ........................(10.1)
Interference
bearings (contact angle of 15) with precision better over incl. over incl.
Clearance
than P5 class, which are used on the main shafts of Fa min = C 0a ................................(10.2)
machine tools, are listed in Table 10.2. 18 0 to 2.5 18 1000
The recommended fitting between the shaft and inner 18 30 0 to 2.5 18 30 2 to 6
ring and between the housing and outer ring are listed
30 50 0 to 2.5 30 50 2 to 6 where Fa min : Minimum axial load (N), {kgf}
in Table 10.1. In the case of fits with housings, the n : Speed (min1)
50 80 0 to 3.5 50 80 3 to 8
lower limit of the fitting range should be selected for 80 120 0 to 4.5 80 120 3 to 9
C 0a : Basic static load rating (N), {kgf}
fixed-end bearings and the upper limit for free-end 120 150 120 150 4 to 12 Nmax : Limiting speed (oil lubrication) (min1)
bearings. 150 180 150 180 4 to 12
As a general rule, an extra light or light preload should 180 250 180 250 5 to 15
be selected for grinding spindles and the main shafts
of machining centers, while a medium preload should
be adopted for the main shafts of lathes requiring
rigidity.
When speeds result in a value of Dpw n (dmn value)
higher than 500000, the preload should be very
carefully studied and selected. In such a case, please Table 10. 2 Preloads for Duplex Angular Contact Ball Bearings
consult with NSK beforehand.
Table 10. 2. 1 Duplex Bearings of Series 79 Table 10. 2. 2 Duplex Bearings of Series 70 Table 10. 2. 3 Duplex Bearings of Series 72
Units : N Units : N Units : N
Preloads Preloads Preloads
Bearing Bearing Bearing
No. Extra light Light Medium Heavy No. Extra light Light Medium Heavy No. Extra light Light Medium Heavy
Preload EL Preload L Preload M Preload H Preload EL Preload L Preload M Preload H Preload EL Preload L Preload M Preload H
7900 C 7 15 29 59 7000 C 12 25 49 100 7200 C 14 29 69 150

7901 C 8.6 15 39 78 7001 C 12 25 59 120 7201 C 19 39 100 200
7902 C 12 25 49 100 7002 C 14 29 69 150 7202 C 19 39 100 200
7903 C 12 25 59 120 7003 C 14 29 69 150 7203 C 24 49 150 290

7904 C 19 39 78 150 7004 C 24 49 120 250 7204 C 34 69 200 390
7905 C 19 39 100 200 7005 C 29 59 150 290 7205 C 39 78 200 390
7906 C 24 49 100 200 7006 C 39 78 200 390 7206 C 60 120 290 590
7907 C 34 69 150 290 7007 C 60 120 250 490 7207 C 75 150 390 780
7908 C 39 78 200 390 7008 C 60 120 290 590 7208 C 100 200 490 980
7909 C 50 100 200 390 7009 C 75 150 340 690 7209 C 125 250 540 1 080
7910 C 50 100 250 490 7010 C 75 150 390 780 7210 C 125 250 590 1 180
7911 C 60 120 290 590 7011 C 100 200 490 980 7211 C 145 290 780 1 570
7912 C 60 120 290 590 7012 C 100 200 540 1 080 7212 C 195 390 930 1 860
7913 C 75 150 340 690 7013 C 125 250 540 1 080 7213 C 220 440 1 080 2 160
7914 C 100 200 490 980 7014 C 145 290 740 1 470 7214 C 245 490 1 180 2 350
7915 C 100 200 490 980 7015 C 145 290 780 1 570 7215 C 270 540 1 230 2 450
7916 C 100 200 490 980 7016 C 195 390 930 1 860 7216 C 295 590 1 370 2 750
7917 C 145 290 640 1 270 7017 C 195 390 980 1 960 7217 C 345 690 1 670 3 330
7918 C 145 290 740 1 470 7018 C 245 490 1 180 2 350 7218 C 390 780 1 860 3 730
7919 C 145 290 780 1 570 7019 C 270 540 1 180 2 350 7219 C 440 880 2 060 4 120
7920 C 195 390 880 1 770 7020 C 270 540 1 270 2 550 7220 C 490 980 2 350 4 710
A 98 A 99
A082-099E.indd 98-99 11/20/13 4:51:54 PM

11. DESIGN OF SHAFTS AND HOUSINGS
11.1 Accuracy and Surface Finish of Shafts 11.2 Shoulder and Fillet Dimensions Table 11. 2 Recommended Minimum Shoulder Heights for
and Housings Use with Metric Series Radial Bearings
The shoulders of the shaft or housing in contact with
Units : mm
If the accuracy of a shaft or housing does not meet the the face of a bearing must be perpendicular to the
specification, the performance of the bearings will be shaft center line. (Refer to Table 11.1) The front face Shaft or Housing
Nominal
affected and they will not provide their full capability. side shoulder bore of the housing for a tapered roller Chamfer Minimun Shoulder Heights
For example, inaccuracy in the squareness of the shaft bearing should be parallel with the bearing axis in Dimensions Fillet h (min.)
h r ra h r rg
shoulder may cause misalignment of the bearing inner order to avoid interference with the cage. Radius
Deep Groove Ball
and outer rings, which may reduce the bearing fatigue The fillets of the shaft and housing should not come in Bearings,
life by adding an edge load in addition to the normal contact with the bearing chamfer; therefore, the fillet Angular Contact (min.) (min.) t
Self-Aligning Ball r r
Ball Bearings,
load. Cage fracture and seizure sometimes occur for radius ra must be smaller than the minimum bearing r (min.) Bearings,
Tapered Roller (min.) (min.)
this same reason. Housings should be rigid in order chamfer dimension r or r1 . Cylindrical Roller b
or ra (max.) Bearings,
Bearings, Spherical
to provide firm bearing support. High rigidity housings Roller Bearings (a) (b)
r1 (min.) Solid Needle Roller
are advantageous also from he standpoint of noise, Housing Bearings
load distribution, etc. Fig. 11. 2 Chamfer Dimensions, Fillet Radius, and
For normal operating conditions, a turned finish or r(min.) or r1(min.) r(min.) or r1(min.) 0.05 0.05 0.2 Fig.11. 2 Shoulder Height
0.08 0.08 0.3
smooth bored finish is sufficient for the fitting surface; 0.1 0.1 0.4
however, a ground finish is necessary for applications
where vibration and noise must be low or where heavy ra h 0.15 0.15 0.6
0.2 0.2 0.8
loads are applied. 0.3 0.3 1 1.25
In cases where two or more bearings are mounted in Bearing
one single-piece housing, the fitting surfaces of the 0.6 0.6 2 2.5
housing bore should be designed so both bearing seats 1 1 2.5 3 Table 11. 3 Shaft Undercut
may be finished together with one operation such as in ra 1.1 1 3.25 3.5 Units : mm
h
-line boring. In the case of split housings, care must 1.5 1.5 4 4.5 Chamfer Dimensions
be taken in the fabrication of the housing so the outer r(min.) r(min.) 2 2 4.5 5 Undercut Dimensions
of Inner and
ring will not become deformed during installation. The or r1(min.) or r1(min.) 2.1 2 5.5 6 Outer Rings
accuracy and surface finish of shafts and housings are 2.5 2 6 r (min.) or r1 (min.) t rg b
listed in Table 11.1 for normal operating conditions. 3 2.5 6.5 7
Shaft 4 3 8 9 1 0.2 1.3 2
1.1 0.3 1.5 2.4
5 4 10 11
Table 11. 1 Accuracy and Roughness of Shaft and 6 5 13 14
1.5 0.4 2 3.2
Housing 7.5 6 16 18 2 0.5 2.5 4
Class of Fig. 11.1 Chamfer Dimensions, Fillet Radius of 2.1 0.5 2.5 4
Item Shaft Housing Bore 9.5 8 20 22 2.5 0.5 2.5 4
Bearings Fig.11.1 Shaft and Housing, and Shoulder Height 12 10 24 27
15 12 29 32
Normal, Class 6 I T3 to I T4 I T4 to I T5
19 15 38 42
3 0.5 3 4.7
Tolerance for 2 2 2 2 4 0.5 4 5.9
The shoulder heights for both shafts and housings for 5 0.6 5 7.4
Out-of-roundness radial bearings should be sufficient to provide good Remarks 1. When heavy axial loads are applied, the shoulder
Class 5, Class 4 I T2 to I T3 I T2 to I T3
height must be sufficiently higher than the
2 2 2 2 support over the face of the bearings, but enough 6 0.6 6 8.6
face should extend beyond the shoulder to permit values listed. 7.5 0.6 7 10
Normal, Class 6 I T3 to I T4 I T4 to I T5
use of special dismounting tools. The recommended
Remarks 2. The fillet radius of the corner is also applicable
Tolerance for 2 2 2 2 to thrust bearings.
Cylindricality minimum shoulder heights for metric series radial Remarks 3. The shoulder diameter is listed instead of
Class 5, Class 4 I T2 to I T3 I T2 to I T3 bearings are listed in Table 11.2 shoulder height in the bearing tables.
2 2 2 2
Nominal dimensions associated with bearing mounting
Tolerance for Normal, Class 6 I T3 I T3 to I T4 are listed in the bearing tables including the proper
Shoulder Runout Class 5, Class 4 I T3 I T3 shoulder diameters. Sufficient shoulder height is
particularly important for supporting the side ribs of
Roughness of Small Bearings 0.8 1.6 tapered roller bearings and cylindrical roller bearings
Fitting Surfaces subjected to high axial loads.
Ra Large Bearings 1.6 3.2
The values of h and ra in Table 11.2 should be adopted
Remarks This table is for general recommendation using in those cases where the fillet radius of the shaft or
radius measuring method, the basic tolerance (I T) housing is as shown in Fig. 11.2 (a), while the values
class should be selected in accordance with the in Table 11.3 are generally used with an undercut fillet
bearing precision class. Regarding the figures of I T, radius produced when grinding the shaft as shown in
please refer to the Appendix Table 11 (page C22). Fig. 11.2 (b).
Remarks In cases that the outer ring is mounted in the
housing bore with interference or that a thin cross-
section bearing is mounted on a shaft and housing,
the accuracy of the shaft and housing should
be higher since this affects the bearing raceway
directly.
A 100 A 101
A100-125E.indd 100-101 11/20/13 4:52:18 PM

DESIGN OF SHAFTS AND HOUSINGS
For thrust bearings, the squareness and contact area 11.3 Bearing Seals (2) Flinger (Slinger) Type Seals (3) Labyrinth Seals
of the supporting face for the bearing rings must To insure the longest possible life of a bearing, it may A flinger is designed to force water and dust away Labyrinth seals are formed by interdigitated segments
be adequate. In the case of thrust ball bearings, the be necessary to provide seals to prevent leakage of by means of the centrifugal force acting on any attached to the shaft and housing that are separated
housing shoulder diameter Da should be less than lubricant and entry of dust, water and other harmful contaminants on the shaft. Sealing mechanisms with by a very small gap. They are particularly suitable for
the pitch circle diameter of the balls, and the shaft material like metallic particles. The seals must be free flingers inside the housing as shown in Fig. 11.6 (a), preventing oil leakage from the shaft at high speeds.
shoulder diameter da should be greater than the pitch from excessive running friction and the probability of (b) are mainly intended to prevent oil leakage, and The type shown in Fig. 11.7 (a) is widely used because
circle diameter of the balls (Fig. 11.3). seizure. They should also be easy to assemble and are used in environments with relatively little dust. of its ease of assembly, but those shown in Fig. 11.7
For thrust roller bearings, it is advisable for the disassemble. It is necessary to select a suitable seal for Dust and moisture are prevented from entering by the (b), (c) have better seal effectiveness.
full contact length between rollers and rings to be each application considering the lubricating method. centrifugal force of flingers shown in Figs 11.6 (c), (d).
supported by the shaft and housing shoulder (Fig.
11.4). 11.3.1 Non-Contact Type Seals
These diameters da and Da are listed in the bearing
tables. Various sealing devices that do not contact the
shaft, such as oil grooves, flingers, and labyrinths,
are available. Satisfactory sealing can usually Table 11. 4 Gaps between Shafts and
Housings for Table 11. 5 Labyrinth Seal Gaps
be obtained with such seals because of their close Oil-Groove Type Seals
running clearance. Centrifugal force may also assist in Units : mm
Units : mm
jd a preventing internal contamination and leakage of the
lubricant. Labyrinth Gaps
Nominal Shaft Diameter Radial Gap
Nominal Shaft Diameter
(1) Oil Groove Seals Radial Gap Axiall Gap
Under 50 0.25 to 0.4
The effectiveness of oil groove seals is obtained by
means of the small gap between the shaft and housing Under 50 0.25 to 0.4 1 to 2
bore and by multiple grooves on either or both of the 50-200 0.5 to 1.5
housing bore and shaft surface (Fig. 11.5 (a), (b)). 50-200 0.5 to 1.5 2 to 5
jDa Since the use of oil grooves alone is not completely
Fig. 11.3 Face Supporting Diameters effective, except at low speeds, a flinger or labyrinth
Fig. 11. 3 for Thrust Ball Bearings type seal is often combined with an oil groove seal
(Fig. 11.5 (c)). The entry of dust is impeded by packing
grease with a consistency of about 200 into the
grooves.
The smaller the gap between the shaft and housing,
jda the greater the sealing effect; however, the shaft and
housing must not come in contact while running. The
recommended gaps are given in Table 11.4.
The recommended groove width is approximately 3 to
5mm, with a depth of about 4 to 5mm. In the case of
sealing methods using grooves only, there should be
three or more grooves.
jDa (a) (b) (c) (d)
Fig. 11.4 Face Supporting Diameters
Fig. 11.4 for Thrust Roller Bearings Fig. 11.6 Examples of Flinger Configurations
(a) (b) (c)

(a) Axial Labyrinth (b) Radial Labyrinth (c) Labyrinth for Self-Aligning Shaft
Fig. 11.5 Examples of Oil Grooves
Fig. 11.7 Examples of Labyrinth Designs
A 102 A 103
A100-125E.indd 102-103 11/20/13 4:52:20 PM

DESIGN OF SHAFTS AND HOUSINGS
11.3.2 Contact Type Seals seals are installed. It is also desirable for the lubricant (2) Felt Seals for grease lubrication, primarily to prevent dust and
The effectiveness of contact seals is achieved by the inside the housing to spread a little between the sliding Felt seals are one of the simplest and most common other foreign matter from entering. Felt seals are not
physical contact between the shaft and seal, which surfaces. However, please be aware that ester-based seals being used for transmission shafts, etc. suitable for circumferential surface speeds exceeding
may be made of synthetic rubber, synthetic resin, grease will cause acrylic rubber material to swell. Also, However, since oil permeation and leakage are 4 m/sec; therefore, it is preferable to replace them with
felt, etc. Oil seals with synthetic rubber lips are most low aniline point mineral oil, silicone-based grease,and unavoidable if oil is used, this type of seal is used only synthetic rubber seals depending on the application.
frequently used. silicon-based oil will cause silicone-based material to
swell. Moreover, urea-based grease will cause fluorine-
based material to deteriorate.
(1) Oil Seals The permissible circumferential speed for oil seals 12. LUBRICATION
Many types of oil seals are used to prevent lubricant varies depending on the type, the finish of the shaft
from leaking out as well as to prevent dust, water, and surface, liquid to be sealed, temperature, shaft 12.1 Purposes of Lubrication 12.2 Lubricating Methods
other foreign matter from entering (Figs. 11.8 and eccentricity, etc. The temperature range for oil The main purposes of lubrication are to reduce friction The various lubricating methods are first divided
11.9) seals is restricted by the lip material. Approximate and wear inside the bearings that may cause premature into either grease or oil lubrication. Satisfactory
In Japan, such oil seals are standardized (Refer to JIS circumferential surface speeds and temperature failure. The effects of lubrication may be briefly bearing performance can be achieved by adopting
B 2402) on the basis of type and size. Since many permitted under favorable conditions are listed in Table explained as follows: the lubricating method which is most suitable for the
oil seals are equipped with circumferential springs to 11.6. particular application and operating condition.
maintain adequate contact force, oil seals can follow When oil seals are used at high circumferential surface (1) Reduction of Friction and Wear In general, oil offers superior lubrication; however,
the non-uniform rotational movement of a shaft to speed or under high internal pressure, the contact Direct metallic contact between the bearing rings, grease lubrication allows a simpler structure around the
some degree. surface of the shaft must be smoothly finished and the rolling elements and cage, which are the basic bearings. A comparison of grease and oil lubrication is
Seal lip materials are usually synthetic rubber including shaft eccentricity should be less than 0.02 to 0.05 mm. components of a bearing, is prevented by an oil film given in Table 12.1.
nitrile, acrylate, silicone, and fluorine. Tetrafluoride The hardness of the shaft's contact surface should be which reduces the friction and wear in the contact
ethylene is also used. The maximum allowable made higher than HRC40 by means of heat treatment areas. Table 12. 1 Comparison of Grease and Oil Lubrication
operating temperature for each material increases in or hard chrome plating in order to gain abrasion (2) Extension of Fatigue Life
this same order. resistance. If possible, a hardness of more than HRC The rolling fatigue life of bearings depends greatly upon Item Grease Lubrication Oil Lubrication
Synthetic rubber oil seals may cause trouble such as 55 is recommended. the viscosity and film thickness between the rolling Housing Structure and Simple May be complex, Careful
overheating, wear, and seizure, unless there is an oil The approximate level of contact surface finish required contact surfaces. A heavy film thickness prolongs the Sealing Method maintenance required.
film between the seal lip and shaft. Therefore, some for several shaft circumferential surface speeds is fatigue life, but it is shortened if the viscosity of the oil Speed Limiting speed is 65% Higher limiting speed.
lubricant should be applied to the seal lip when the given in Table 11.7. is too low so the film thickness is insufficient.
to 80% of that with oil
lubrication.
(3) Dissipation of Frictional Heat and Cooling Cooling Effect Poor Heat transter is possible
Circulation lubrication may be used to carry away using forced oil
circulation.
frictional heat or heat transferred from the outside to
Fluidity Poor Good
prevent the bearing from overheating and the oil from
Full Lubricant Sometimes difficult Easy
deteriorating. Replacement
Table 11. 6 Permissible Circumferential Surface Speeds (4) Others
and Temperature Range for Oil Seals Removal of Foreign Removal of particles Easy
Adequate lubrication also helps to prevent foreign Matter from grese is
Permissible Operating material from entering the bearings and guards against impossible.
Seal Materials Circumferential Temperature corrosion or rusting. External Surroundings seldom Often leaks without
Speeds(m/sec) Range( C)(1) Contamination due to contaminated by leakage. proper countermeasures.
Leakage Not suitable if external
Nitrile Rubber Under 16 25 to +100 contamination must be
avoided.
Synthetic Acrylic Rubber Under 25 15 to +130

Rubber
Silicone Rubber Under 32 70 to +200 12.2.1 Grease Lubrication
Fluorine- (1) Grease Quantity
Fig. 11.8 Example of Application containes Rubber Under 32 30 to +200 The quantity of grease to be packed in a housing
Fig. 11 .8 of Oil Seal (1)
Tetrafluoride Ethylene Resin Under 15 50 to +220 depends on the housing design and free space,
grease characteristics, and ambient temperature. For
Note (1) The upper limit of the temperature range may be example, the bearings for the main shafts of machine
raised about 20 C for operation for short intervais. tools, where the accuracy may be impaired by a small
temperature rise, require only a small amount of
Table 11. 7 Shaft Circumferential grease. The quantity of grease for ordinary bearings is
Surface Speeds and Finish determined as follows.
of Contact Surfaces Sufficient grease must be packed inside the bearing
including the cage guide face. The available space
Circumferential Surface Surface Finish
Speeds(m/s) Ra (m) inside the housing to be packed with grease depends
on the speed as follows:
Under 5 0.8 1/2 to 2/3 of the space When the speed is less than
5 to 10 0.4
50% of the limiting speed.
1/3 to 1/2 of the space When the speed is more than
Over 10 0.2 50% of the limiting speed.
Fig. 11.9 Example of Application
Fig. 1 1.9 of Oil Seal (2)
A 104 A 105
A100-125E.indd 104-105 11/20/13 4:52:21 PM

LUBRICATION
(2) Replacement of Grease the discharge side is made larger than the partitioned (4) Grease Life of Sealed Ball Bearings (b) Operating Temperature, T
Grease, once packed, usually need not be replenished side so it can retain the old grease, which is removed When grease is packed into single-row deep groove For general purpose grease (1)
for a long time; however, for severe operating periodically by removing the cover. ball bearings, the grease life may be estimated using 70 CT110 C
conditions, grease should be frequently replenished Equation (12.1) or (12.2) or Fig. 12.3:
or replaced. In such cases, the bearing housing should (3) Replenishing Interval (General purpose grease (1)) For wide-range grease (2)
be designed to facilitate grease replenishment and Even if high-quality grease is used, there is
n n
replacement.
When replenishment intervals are short, provide
deterioration of its properties with time; therefore,
periodic replenishment is required. Figs 12.2 (1) and
log t = 6.54 2.6
Nmax (
0.025 0.012
Nmax
T ) 70 CT130 C
replenishment and discharge ports at appropriate (2) show the replenishment time intervals for various (12.1) When T<70 C assume T = 70 C
positions so deteriorated grease is replaced by fresh bearing types running at different speeds. Figs.12.2 (1) (Wide-range grease (2))
grease. For example, the housing space on the grease and (2) apply for the condition of high-quality lithium (c) Bearing Loads
soap-mineral oil grease, bearing temperature of 70C, n n The bearing loads should be about 1/10 or less of the
supply side can be divided into several sections with
partitions. The grease on the partitioned side gradually and normal load (P/C=0.1).
log t = 6.12 1.4
Nmax (
0.018 0.006
Nmax
T ) basic load rating C r.
passes through the bearings and old grease forced Temperature (12.2)
from the bearing is discharged through a grease valve If the bearing temperature exceeds 70 C, the Notes (1) Mineral-oil base greases (e.g. lithium soap
(Fig. 12.1). If a grease valve is not used, the space on replenishment time interval must be reduced by half where t : Average grease life, (h) base grease) which are often used over a
for every 15C temperature rise of the bearings. n : Speed (min1) temperature range of around 10 to 110 C.
Grease Nmax : Limiting speed with grease lubrication Notes (2) Synthetic-oil base greases are usable over
A a wide temperature range of around 40
In case of ball bearings especially, the replenishing (min1)
time interval can be extended depending on used (values for ZZ and VV types listed in the to 130 C.
grease type. (For example, high-quality lithium soap- bearing tables)
synthetic oil grease may extend about two times of T : Operating temperature C 12.2.2 Oil Lubrication
replenishing time interval shown in Fig.12.2 (1). If Equations (12.1) and (12.2) and Fig. 12.3 apply under (1) Oil Bath Lubrication
the temperature of the bearings is less than 70C, the the following conditions: Oil bath lubrication is a widely used with low or
usage of lithium soap-mineral oil grease or lithium medium speeds. The oil level should be at the center
soap-synthetic oil grease is appropriate.) (a) Speed, n
of the lowest rolling element. It is desirable to provide
It is advisable to consult NSK. n a sight gauge so the proper oil level may be maintained
A Load 0.25 N 1 (Fig. 12.4)
A- A max
The replenishing time interval depends on the
Fig. 12.1 Combination of Partitioned Grease magnitude of the bearing load. n n (2) Drip-Feed Lubrication
Fig. 12. 1 Reservoir and Grease Valve Please refer to Fig.12.2 (3). when <0.25, assume = 0.25
Nmax Nmax
If P/C exceeds 0.16, it is advisable to consult NSK. Drip feed lubrication is widely used for small ball
bearings operated at relatively high speeds. As shown
Radial Ball Bearings in Fig. 12.5, oil is stored in a visible oiler. The oil drip
Cylindrical Roller Bearings rate is controlled with the screw in the top.
h h h
20 000 10 000 150 000
7 000 100 000 General purpose grease
Wide-range grease
20 000 10 000 5 000
4 000 50 000
Grease Replenishment Interval, tf
Grease Replenishment Interval, tf
8 000
6 000 3 000
10 000 5 000
d=
d=
Average grease life, t

20
20 000
1
8 000 4 000 2 000

0
6 000 3 000 T=7

40 50
T=
30
0
3 0 40
20
5 000 7
60 7
10 000 0
80
80 100
4 000 2 000 80
120 14 0
1 000
50 60
90
160 2
70 8
90
10 1
3 000 800 100

240 280
140 1
5 000 100
0 20
340 420
180 220
110
0
600
0
500
260 300
2 000 1 000 500 3 000 120

60
110
800 400 130
2 000
600 300
1 000 500
800 400 200 1 000
600 300
500
400 200 100
200 300 400 600 800 1 000 2 000 4 000 6 000 10 000 20 000 100 200 300 400 600 1 000 2 000 4 000 6 000 10 000
Speed n min1 Speed n min1
200
0.25 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
(1) Radial Ball Bearings, Cylindrical Roller Bearings (2) Tapered Roller Bearings, Spherical Roller Bearings n/N max Fig. 12.5 Drip Feed
(3) Load factor P/C 0.06 0.1 0.13 0.16
Fig. 12.3 Grease Life of Sealed Ball Bearings Fig. 12.4 Oil Bath Lubrication Fig. 12.5 Lubrication
Load factor 1.5 1 0.65 0.45
A 106 Fig. 12.2 Grease Replenishment Intervals A 107
A100-125E.indd 106-107 11/20/13 4:52:22 PM

LUBRICATION
(3) Splash Lubrication (5) Jet Lubrication This lubricating method is used in bearings for the high
With this lubricating method, oil is splashed onto the Jet lubrication is often used for ultra high speed speed spindles of machine tools, high speed pumps,
roll necks of rolling mills, etc (Fig. 12.9). Oil
bearings by gears or a simple rotating disc installed bearings, such as the bearings in jet engines with a
near bearings without submerging the bearings in oil. dmn valve (dm: pitch diameter of rolling element set For oil mist lubrication of large bearings, it is advisable
Oil
It is commonly used in automobile transmissions in mm; n: rotational speed in min1) exceeding one to consult NSK.
and final drive gears. Fig. 12.6 shows this lubricating million. Lubricating oil is sprayed under pressure from
method used on a reduction gear. one or more nozzles directly into the bearing. (7) Oil/Air Lubricating Method
Fig. 12.8 shows an example of ordinary jet lubrication. Using the oil/air lubricating method, a very small
(4) Circulating Lubrication The lubricating oil is sprayed on the inner ring and amount of oil is discharged intermittently by a
Circulating lubrication is commonly used for high cage guide face. In the case of high speed operation, constant-quantity piston into a pipe carrying a constant
speed operation requiring bearing cooling and for the air surrounding the bearing rotates with it causing flow of compressed air. The oil flows along the wall of
bearings used at high temperatures. As shown in Fig. the oil jet to be deflected. The jetting speed of the the pipe and approaches a constant flow rate.
12.7 (a), oil is supplied by the pipe on the right side, oil from the nozzle should be more than 20 % of the The major advantages of oil/air lubrication are:
circumferential speed of the inner ring outer surface (a) Since the minimum necessary amount of oil is (a) (b)
it travels through the bearing, and drains out through
the pipe on the left. After being cooled in a reservoir, it (which is also the guide face for the cage). supplied, this method is suitable for high speeds
returns to the bearing through a pump and filter. More uniform cooling and a better temperature because less heat is generated.
distribution is achieved using more nozzles for a given (b) Since the minimum amount of oil is fed Fig. 12.8 Jet Lubrication
The oil discharge pipe should be larger than the supply
pipe so an excessive amount of oil will not back up in amount of oil. It is desirable for the oil to be forcibly continuously, bearing temperature remains stable.
the housing. discharged so the agitating resistance of the lubricant Also, because of the small amount of oil, there is
can be reduced and the oil can effectively carry away almost no atmospheric pollution.
the heat. (c) Since only fresh oil is fed to the bearings, oil
deterioration need not be considered.
(6) Oil Mist Lubrication (d) Since compressed air is always fed to the bearings,
Oil mist lubrication, also called oil fog lubrication, the internal pressure is high, so dust, cutting fluid, etc.
utilizes an oil mist sprayed into a bearing. This method cannot enter.
has the following advantages: For these reasons, this method is used in the main
(a) Because of the small quantity of oil required, the spindles of machine tools and other high speed
oil agitation resistance is small, and higher speeds are applications (Fig. 12.1O).
possible.
(b) Contamination of the vicinity around the bearing is
slight because the oil leakage is small.
(c) It is relatively easy to continuously supply fresh oil;
therefore, the bearing life is extended.
Fig. 12.9 Oil Mist Lubrication
Fig. 12.6 Splash Lubrication
Oil
Oil/air inlets 5 places
Oil
Oil
(a) (b) (c) Oil/air discharge ports 2 places

Fig. 12.7 Circulating Lubrication Fig. 12.10 Oil/Air Lubrication
A 108 A 109
A100-125E.indd 108-109 11/20/13 4:52:23 PM

LUBRICATION
12.3 Lubricants Table 12.2 Grease Properties

12.3.1 Lubricating Grease Name
Grease is a semi-solid lubricant consisting of base oil, (Popular Complex Base
name) Sodium Grease Calcium Grease Mixed Base Non-Soap Base Grease
Lithium Grease Grease
a thickener and additives. The main types and general (Fiber Grease) (Cup Grease) Grease
(Complex Grease)
(Non-Soap Grease)
properties of grease are shown in Table 12.2. It should
be remembered that different brands of the same type Thickener Ca Complex Soap,
of grease may have different properties. Na + Ca Soap, Urea, Bentonite, Carbon Black, Fluoric
Al Complex Soap,
Li Soap Na Soap Ca Soap Li + Ca Soap, Compounds, Heat Resistant Organic
Li Complex Soap, Compound, etc.
(1) Base Oil etc.
etc.
Mineral oils or synthetic oils such as silicone or diester Base
Synthetic Oil (Ester Oil,
oil are mainly used as the base oil for grease. The Oil Diester Oil, Polyatomic Ester Oil,
lubricating properties of grease depend mainly on the Mineral Oil Polyatomic Silicone Oil Mineral Oil Mineral Oil Mineral Oil Mineral Oil Mineral Oil Synthetic Hydrocarbon
Properties Ester Oil Oil, Silicone Oil, Fluoric
characteristics of its base oil. Therefore, the viscosity Based Oil)
of the base oil is just as important when selecting
Dropping
grease as when selecting an oil. Usually, grease made Point,C
170 to 195 170 to 195 200 to 210 170 to 210 70 to 90 160 to 190 180 to 300 > 230 > 230
with low viscosity base oils is more suitable for high Working
speeds and low temperatures, while greases made 20 to +110 50 to +130 50 to +160 20 to +130 20 to +60 20 to +80 20 to +130 10 to +130 < +220
Temperatures, C
with high viscosity base oils are more suited for high Working
temperatures and heavy loads. 70 100 60 70 40 70 70 70 40 to 100
Speed, %(1)
However, the thickener also influences the lubricating Mechanical
properties of grease; therefore, the selection criteria for Good Good Good Good Poor Good Good Good Good
Stability
grease is not the same as for lubricating oil. Moreover, Pressure Fair Fair Poor Fair Poor Fair to Good Fair to Good Fair Fair
please be aware that ester-based grease will cause Resistance
acrylic rubber material to swell, and that silicone-based Good Good Good Poor Good Poor for Na Good Good Good
Water Resistance
grease will cause silicone-based material to swell. Soap Grease
Rust Prevention Good Good Poor Poor to Good Good Fair to Good Fair to Good Fair to Good Fair to Good
(2) Thickener
As thickeners for lubricating grease, there are several General Good low Mainly for high Long and short Extreme pressure Often used for Suitable Mineral oil base grease is middle
purpose temperature temperature fiber types are grease containing roller bearings for extreme and high temperature purpose
types of metallic soaps, inorganic thickeners such as grease used and torque applications. available. Long high viscosity and large ball pressures lubricant. Synthetic oil base grease
silica gel and bentonite, and heat resisting organic for numerous characteristics. Unsuitable fiber grease is mineral oil and bearing. mechanically is recommended for low or high
thickeners such as polyurea and fluoric compounds. applications Often used for for bearings unsuitable for extreme pressure stable temperature. Some silicone and
The type of thickener is closely related to the grease small motors for high and high speeds. additive (Pb fluoric oil based grease have poor
dropping point ( 1); generally, grease with a high Remarks and instrument low speeds or Attention to soap, etc.) has rust prevention and noise.
bearings. Pay heavy loads or water and high high pressure
dropping point also has a high temperature capability attention to those having temperature is resistance.
during operation. However, this type of grease rust caused numerous requred.
does not have a high working temperature unless by insulation sliding-contact
the base oil is heat-resistant. The highest possible varnish. areas (roller
working temperature for grease should be determined bearings, etc.)
considering the heat resistance of the base oil.
Note (1) The values listed are percentages of the limiting Remarks The grease properties shown here can vary between brands.
The water resistance of grease depends upon the type speeds given in the bearing tables.
of thickener. Sodium soap grease or compound grease
containing sodium soap emulsifies when exposed
to water or high humidity, and therefore, cannot be Table 12.3 Consistency and Working Conditions
used where moisture is prevalent. Moreover, please be
aware that urea-based grease will cause fluorine-based (3) Additives Consistency 0 1 2 3 4
material to deteriorate. Number
Grease often contains various additives such
as antioxidants, corrosion inhibitors, and extreme Consistency(1)
355 to 385 310 to 340 265 to 295 220 to 250 175 to 205
pressure additives to give it special properties. It is 1/10 mm
Note (1) The grease dropping point is that temperature
at which a grease heated in a specified small recommended that extreme pressure additives be For centralized For centralized For general use For general use For high
container becomes sufficiently fluid to drip. used in heavy load applications. For long use without oiling oiling temperatures
Working
replenishment, an antioxidant should be added. Conditions
When fretting is When fretting is For sealed ball For sealed ball For grease seals
likely to occur likely to occur bearings bearings
(Application)
(4) Consistency For low For high
temperatures temperatures
Consistency indicates the softness of grease. Table
12.3 shows the relation between consistency and Note (1) Consistency: The depth to which a cone descends into grease when a specified weight is applied, indicated in units
working conditions. of 1/10mm. The larger the value, the softer the grease.
A 110 A 111
A100-125E.indd 110-111 11/20/13 4:52:24 PM

LUBRICATION
(5) Mixing Different Types of Grease with increasing bearing load and size. Oil Replacement Intervals If moisture may enter or if foreign matter may be
In general, different brands of grease must not be Table 12.4 gives generally recommended viscosities for Oil replacement intervals depend on the operating mixed in the oil, then the oil replacement interval must
mixed. Mixing grease with different types of bearings under normal operating conditions. conditions and oil quantity. be shortened.
thickneners may destroy its composition and physical For use when selecting the proper lubricating oil, Fig. In those cases where the operating temperature is Mixing different brands of oil must be prevented for
properties. Even if the thickeners are of the same 12.11 shows the relationship between oil temperature less than 50C, and the environmental conditions the same reason given previously for grease.
type, possible differences in the additive may cause and viscosity, and examples of selection are shown in are good with little dust, the oil should be replaced
detrimental effects. Table 12.5. approximately once a year. However, in cases where
the oil temperature is about 100C, the oil must be
changed at least once every three months.
12.3.2 Lubricating Oil Table 12. 4 Bearing Types and Proper
Viscosity of Lubricating Oils
The lubricating oils used for rolling bearings are
usually highly refined mineral oil or synthetic oil that Proper Viscosity
have a high oil film strength and superior oxidation and Bearing Type at Operating
Temperature
corrosion resistance. When selecting a lubricating oil, Table 12. 5 Examples of Selection Lubricating Oils
the viscosity at the operating conditions is important. Ball Bearings and Higher than 13mm2/s
If the viscosity is too low, a proper oil film is not Cylindrical Roller Bearings Operating Speed Light or normal Load Heavy or Shock Load
formed and abnormal wear and seizure may occur. On Tapered Roller Bearings and Higher than 20mm2/s Temperature
the other hand, if the viscosity is too high, excessive Spherical Roller Bearings 30 to 0 C Less than limiting speed ISO VG 15, 22, 32 (refrigerating
viscous resistance may cause heating or large power Spherical Thrust Roller Bearings Higher than 32mm2/s machine oil)
loss. In general, low viscosity oils should be used at
high speed; however, the viscosity should increase Remarks 1mm2/s=1cSt (centistokes) Less than 50% of limiting ISO VG 32, 46, 68 (bearing oil, ISO VG 46, 68, 100 (bearing oil,
speed turbine oil) turbine oil)
0 to 50 C 50 to 100% of limiting ISO VG 15, 22, 32 (bearing oil, ISO VG 22, 32, 46 (bearing oil,
speed turbine oil) turbine oil)
Redwood Saybolt More than limiting speed ISO VG 10, 15, 22 (bearing oil)
(Seconds) (Seconds) mm2/s
ISO Viscosity Grade
2 000 assumed V.I.80 Less than 50% of limiting ISO VG 100, 150, 220 (bearings oil) ISO VG 150, 220, 320 (bearing oil)
5 000 5 000 1 000 speed
A : VG 7 H : VG 100
2 000 2 000 500 B : VG 10 J : VG 150 50 to 100% of limiting ISO VG 46, 68, 100 (bearing oil, ISO VG 68, 100, 150 (bearing oil,
300 C : VG 15 K : VG 220 50 to 80 C
1 000 1 000 200 D : VG 22 L : VG 320 speed turbine oil) turbine oil)
500 E : VG 32 M : VG 460 More than limiting speed ISO VG 32, 46, 68 (bearing oil,
500 100 F : VG 46 N : VG 680
300 300 G : VG 68 turbine oil)
200 200 50
40
Viscosity
30
100 A B C D E F G H J K L M N Less than 50% of limiting ISO VG 320, 460 (bearing oil) ISO VG 460, 680 (bearing oil,
100 20
80 speed gear oil)
80
60 50 to 100% of limiting ISO VG 150, 220 (bearing oil) ISO VG 220, 320 (bearing oil)
60 10 80 to 110 C
50 speed
50 More than limiting speed ISO VG 68, 100 (bearing oil,
40 turbine oil)
5
40 4
-20 0 20 40 60 80 100 120 140 160 C Remarks 1. For the limiting speed, use the values listed in the bearing tables.
Remarks 2. Refer to Refrigerating Machine Oils (JIS K 2211), Bearing Oils (JIS K 2239), Turbine Oils (JIS K
-20 0 20 40 60 80 100 120 160 200 240 280 320 F 2213), Gear Oils (JIS K 2219).
Remarks 3. If the operating temperature is near the high end of the temperature range listed in the left column,
Temperature
select a high viscosity oil.
Remarks 4. If the operating temperature is lower than -30C or higher than 110C , it is advisable to consult
Fig. 12.11 Temperature-Viscosity Chart NSK.
A 112 A 113
A100-125E.indd 112-113 11/20/13 4:52:25 PM

13. BEARING MATERIALS
The bearing rings and rolling elements of rolling 13.1 Materials for Bearing Rings and Rolling NSK uses highly pure vacuum-degassed bearing 13.2 Cage Materials
bearings are subjected to repetitive high pressure with Elements steel containing a minimum of oxygen, nitrogen, and The low carbon steels shown in Table 13.5 are the main
a small amount of sliding. The cages are subjected to Primarily, high carbon chromium bearing steel hydrogen compound impurities. The rolling fatigue life ones for the pressed cages for bearings. Depending on
tension and compression and sliding contact with (Table 13.1) is used for the bearing rings and rolling of bearings has been remarkably improved using this the purpose, brass or stainless steel may be used. For
the rolling elements and either or both of the bearing elements. Most NSK bearings are made of SUJ2 material combined with the appropriate heat treatment. machined cages, high strength brass (Table 13.6) or
rings. among the JIS steel types listed in Table 13.1, while For special purpose bearings, high temperature bearing carbon steel (Table 13.5) is used. Sometimes synthetic
Therefore, the materials used for the rings, rolling the larger bearings generally use SUJ3. The chemical steel, which has superior heat resistance, and stainless resin is also used.
elements, and cages require the following composition of SUJ2 is approximately the same as steel having good corrosion resistance may be used.
characteristics: AISI 52100 specified in the USA, DIN 100 Cr6 in The chemical composition of these special materials
High rolling contact Germany, and BS 535A99 in England. are given in Tables 13.3 and 13.4.
fatigue strength For bearings that are subjected to very severe shock
Material High hardness loads, carburized low-carbon alloy steels such as
characteristics chrome steel, chrome molybdenum steel, nickel
High wear chrome molybdenum steel, etc. are often used. Such Table 13. 4 Chemical Composition of Stainless Steel for
required for
resistance steels, when they are carburized to the proper depth Rolling Bearing (Major Elements)
bearing rings Characteristics
and rolling High dimensional and have sufficient surface hardness, are more shock Chemical Composition (%)
stability required for resistant than normal, through-hardened bearing steels Standard Symbols
elements cage material C Si Mn P S Cr Mo
High mechanical because of the softer energy-absorbing core. The Less than Less than Less than Less than Less than
chemical composition of common carburized bearing JIS G 4303 SUS 440 C 0.95 to 1.20 1.00 1.00 0.040 0.030 16.00 to 18.00 0.75
strength
steels is listed in Table 13.2. SAE J 405 51440 C 0.95 to 1.20 Less than Less than Less than Less than
16.00 to 18.00 Less than
Other necessary characteristics, such as easy 1.00 1.00 0.040 0.030 0.75
production, shock and heat resistance, and corrosion
resistance, are required depending on individual
applications.
Table 13. 5 Chemical Composition of Steel sheet and Carbon Steel
for Cages (Major Elements)
Table 13. 1 Chemical Composition of High-Carbon Chromium Bearing Steel (Major Elements)
Chemical Composition (%)
Chemical Composition (%) Classification Standard Symbols
Standard Symbols C Si Mn P S
C Si Mn P S Cr Mo Less than Less than Less than Less than
JIS G 3141 SPCC 0.12 0.50 0.04 0.045
JIS G 4805 SUJ 2 0.95 to 1.10 0.15 to 0.35 Less than Less than Less than 1.30 to 1.60 Steel sheet and
0.50 0.025 0.025 Less than Less than Less than
Less than Less than
strip for pressed BAS 361 SPB 2 0.13 to 0.20 0.30 0.25 to 0.60 0.03 0.030
SUJ 3 0.95 to 1.10 0.40 to 0.70 0.90 to 1.15 0.025 0.025 0.90 to 1.20 cages Less than Less than
JIS G 3311 S 50 CM 0.47 to 0.53 0.15 to 0.35 0.60 to 0.90 0.03 0.035
SUJ 4 0.95 to 1.10 0.15 to 0.35 Less than Less than Less than 1.30 to 1.60 0.10 to 0.25
0.50 0.025 0.025
Carbon steel for JIS G 4051 S 25 C 0.22 to 0.28 0.15 to 0.35 0.30 to 0.60 Less than 0.03 Less than 0.035
ASTM A 295 52100 0.93 to 1.05 0.15 to 0.35 0.25 to 0.45 Less than Less than 1.35 to 1.60 Less than machined cages
0.025 0.015 0.10
Remarks BAS is Japanese Bearing Association Standard.
Table 13. 2 Chemical Composition of Carburizing Bearing Steels (Major Elements)
Standard Symbols Table 13. 6 Chemical Composition of High Strength Brass for Machined Cages
C Si Mn P S Ni Cr Mo
Less than Less than Less than Chemical Composition (%)
JIS G 4052 SCr 420 H 0.17 to 0.23 0.15 to 0.35 0.55 to 0.95 0.030 0.030 0.25 0.85 to 1.25
Standard Symbols Impurities
SCM 420 H 0.17 to 0.23 0.15 to 0.35 0.55 to 0.95 Less than Less than Less than 0.85 to 1.25 0.15 to 0.35
Cu Zn Mn Fe Al Sn Ni
0.030 0.030 0.25 Pb Si
SNCM 220 H 0.17 to 0.23 0.15 to 0.35 0.60 to 0.95 Less than Less than 0.35 to 0.75 0.35 to 0.65 0.15 to 0.30 CAC301 Less than Less than Less than Less than
0.030 0.030 JIS H 5120 (HBsC 1) 55.0 to 60.0 33.0 to 42.0 0.1 to 1.5 0.5 to 1.5 0.5 to 1.5 1.0 1.0 0.4 0.1
SNCM 420 H 0.17 to 0.23 0.15 to 0.35 0.40 to 0.70 Less than Less than 1.55 to 2.00 0.35 to 0.65 0.15 to 0.30 Less than
0.030 0.030 JIS H 3250 C 6782 56.0 to 60.5 Residual 0.5 to 2.5 0.1 to 1.0 0.2 to 2.0 0.5
JIS G 4053 SNCM 815 0.12 to 0.18 0.15 to 0.35 0.30 to 0.60 Less than Less than 4.00 to 4.50 0.70 to 1.00 0.15 to 0.30
0.030 0.030 Remarks Improved HBsC 1 is also used.
ASTM A 534 8620 H 0.17 to 0.23 0.15 to 0.35 0.60 to 0.95 Less than Less than 0.35 to 0.75 0.35 to 0.65 0.15 to 0.25
0.025 0.015
4320 H 0.17 to 0.23 0.15 to 0.35 0.40 to 0.70 Less than Less than 1.55 to 2.00 0.35 to 0.65 0.20 to 0.30
0.025 0.015
9310 H 0.07 to 0.13 0.15 to 0.35 0.40 to 0.70 Less than Less than 2.95 to 3.55 1.00 to 1.40 0.08 to 0.15
0.025 0.015
Table 13. 3 Chemical Composition of High Speed Steel for Bearings Used at High Temperatures
Standard Symbols
C Si Mn P S Cr Mo V Ni Cu Co W
AISI M50 0.77 to 0.85 Less
0.25
than Less than Less than
0.35 0.015
Less than 3.75 to 4.25 4.00 to 4.50 0.90 to 1.10 Less than Less than Less than Less than
0.015 0.10 0.10 0.25 0.25
A 114 A 115
A100-125E.indd 114-115 11/20/13 4:52:26 PM

14. BEARING HANDLING
14.1 Precautions for Proper Handling of After the bearings are cleaned with filtered oil, they (2) Shrink Fits
Bearings should be protected to prevent corrosion. Since press fitting large bearings requires a large force,
Since rolling bearings are high precision machine Prelubricated bearings must be used without cleaning. a shrink fit is widely used. The bearings are first heated
parts, they must be handled accordingly. Even if high Bearing mounting methods depend on the bearing type in oil to expand them before mounting.
quality bearings are used, their expected performance and type of fit. As bearings are usually used on rotating This method prevents an excessive force from being
cannot be achieved if they are not handled properly. shafts, the inner rings require a tight fit. imposed on the bearings and allows mounting them in
The main precautions to be observed are as follows: Bearings with cylindrical bores are usually mounted a short time.
by pressing them on the shafts (press fit) or heating The expansion of the inner ring for various temperature
(1) Keep Bearings and Surrounding Area Clean them to expand their diameter (shrink fit). Bearings differences and bearing sizes is shown in Fig. 14.3.
with tapered bores can be mounted directly on tapered The precautions to follow when making shrink fits are
Dust and dirt, even if invisible to the naked eye, have shafts or cylindrical shafts using tapered sleeves.
harmful effects on bearings. It is necessary to prevent as follows:
Bearings are usually mounted in housings with a loose
the entry of dust and dirt by keeping the bearings and fit. However, in cases where the outer ring has an
their environment as clean as possible. (a) Do not heat bearings to more than 120C.
interference fit, a press may be used. Bearings can be (b) Put the bearings on a wire net or suspend them in
interference-fitted by cooling them before mounting an oil tank in order to prevent them from touching
(2) Careful Handling using dry ice. In this case, a rust preventive treatment Fig. 14.1 Press Fitting Inner Ring the tank's bottom directly.
Heavy shocks during handling may cause bearings to must be applied to the bearing because moisture in the (c) Heat the bearings to a temperature 20 to 30C
be scratched or otherwise damaged possibly resulting air condenses on its surface. higher than the lowest temperature required for
in their failure. Excessively strong impacts may cause mounting without interference since the inner ring
brinelling, breaking, or cracking. 14.2.1 Mounting of Bearings with Cylindrical Bores will cool a little during mounting.
(1) Press Fits (d) After mounting, the bearings will shrink in the
(3) Use Proper Tools axial direction as well as the radial direction while
Fitting with a press is widely used for small bearings.
Always use the proper equipment when handling A mounting tool is placed on the inner ring as shown cooling. Therefore, press the bearing firmly against
bearings and avoid general purpose tools. in Fig. 14.1 and the bearing is slowly pressed on the shaft shoulder using locating methods to avoid
the shaft with a press until the side of the inner ring a clearance between the bearing and shoulder.
(4) Prevent Corrosion rests against the shoulder of the shaft. The mounting
Since perspiration on the hands and various other tool must not be placed on the outer ring for press NSK Bearing Induction Heaters
contaminants may cause corrosion, keep the hands mounting, since the bearing may be damaged. Before Besides heating in oil, NSK Bearing Heaters, which
clean when handling bearings. Wear gloves if possible. mounting, applying oil to the fitted shaft surface is use electromagnetic induction to heat bearings, are
Pay attention to rust of bearing caused by corrosive recommended for smooth insertion. The mounting widely used. (Refer to Page C7.)
gasses. method using a hammer should only be used for small In NSK Bearing Heaters, electricity (AC) in a coil
ball bearings with minimally tight fits and when a press produces a magnetic field that induces a current inside
14.2 Mounting is not available. In the case of tight interference fits or the bearing that generates heat. Consequently, without
The method of mounting rolling bearings strongly for medium and large bearings, this method should not Fig. 14.2 Simultaneous Press Fitting of Inner and Outer Rings using flames or oil uniform heating in a short time is
affects their accuracy, life, and performance, so be used. Any time a hammer is used, a mounting tool possible, making bearing shrink fitting efficient and
their mounting deserves careful attention. Their must be placed on the inner ring. clean.
characteristics should first be thoroughly studied, and When both the inner and outer rings of non-separable In the case of relatively frequent mounting and
then they should be mounted in the proper manner. bearings, such as deep groove ball bearings, require dismounting such as cylindrical roller bearings for roll
It is recommended that the handling procedures for tight-fit, a mounting tool is placed on both rings as necks of rolling mills and for railway journal boxes,
bearings be fully investigated by the design engineers shown in Fig. 14.2, and both rings are fitted at the induction heating should be used for mounting and
m
and that standards be established with respect to the same time using a screw or hydraulic press. Since the dismounting inner rings.
240
following items: outer ring of self-aligning ball bearings may deflect a
r6
7 0 C
= 8 ence
mounting tool such as that shown in Fig. 14.2 should 220
60 C
0
always be used for mounting them.
&T iffer
C
(1) Cleaning the bearings and related parts. 200
D
(2) Checking the dimensions and finish of related In the case of separable bearings, such as cylindrical C
ure
180
roller bearings and tapered roller bearings, the inner 50
rat
parts. 160 C p6
pe
and outer rings may be mounted separately. Assembly
Bore Expansion
(3) Mounting 40
(4) Inspection after mounting. of the inner and outer rings, which were previously 140 Tem C n6
mounted separately, should be done carefully to align 30
(5) Supply of lubricants. 120
the inner and outer rings correctly. Careless or forced
20
100 C m5
Bearings should not be unpacked until immediately assembly may cause scratches on the rolling contact
k5
before mounting. When using ordinary grease surfaces. 80
lubrication, the grease should be packed in the 60 j5

bearings without first cleaning them. Even in the case 40
of ordinary oil lubrication, cleaning the bearings is not 20
required. However, bearings for instruments or for 80 120 180 250 315 400 500
mm
high speed operation must first be cleaned with clean Bore Diameter
filtered oil in order to remove the anti-corrosion agent. Fig. 14.3 Temperature and Thermal Expansion of Inner Ring
A 116 A 117
A100-125E.indd 116-117 11/20/13 4:52:27 PM

BEARING HANDLING
14.2.2 Mounting of Bearings with Tapered Bores become too tight and the true residual clearance may Table 14.1 Mounting of Spherical Roller Bearings with Tapered Bores
Bearings with tapered bores are mounted on tapered become too small. In this case, as shown in Fig. 14.9. Units : mm
shafts directly or on cylindrical shafts with adapters one half of the total clearance at points and b (which
or withdrawal sleeves (Figs. 14.4 and 14.5). Large are on a horizontal line passing through the Bearing Bore Reduction in Radial Push-in amount in axial direction Minimum Permissible
bearing center) and c (which is at the lowest position Diameter Clearance Residual Clearance
spherical roller bearings are often mounted using
hydraulic pressure. Fig. 14.6 shows a bearing of the bearing) may be used as the residual clearance. d Taper 1 : 12 Taper 1 : 30
mounting utilizing a sleeve and hydraulic nut. Fig. 14.7 When a self-aligning ball bearing is mounted on a shaft over incl. min. max. min. max. min. max. CN C3
shows another mounting method. Holes are drilled in with an adapter, be sure that the residual clearance
does not become too small. Sufficient clearance for 30 40 0.025 0.030 0.40 0.45 0.010 0.025
the sleeve which are used to feed oil under pressure to 40 50 0.030 0.035 0.45 0.55 0.015 0.030
the bearing seat. As the bearing expands radially, the easy alignment of the outer ring must be allowed. 50 65 0.030 0.035 0.45 0.55 0.025 0.035
sleeve is inserted axially with adjusting bolts. 65 80 0.040 0.045 0.60 0.70 0.030 0.040
Spherical roller bearings should be mounted while 14.3 Operation Inspection
80 100 0.045 0.055 0.70 0.85 1.75 2.15 0.035 0.050
checking their radial-clearance reduction and referring After the mounting has been completed, a running 100 120 0.050 0.060 0.75 0.90 1.9 2.25 0.045 0.065
to the push-in amounts listed in Table 14.1. The radial test should be conducted to determine if the bearing 120 140 0.060 0.070 0.90 1.1 2.25 2.75 0.055 0.080
clearance must be measured using clearance gauges. has been mounted correctly. Small machines may be
140 160 0.065 0.080 1.0 1.3 2.5 3.25 0.060 0.100
In this measurement, as shown in Fig. 14.8, the manually operated to assure that they rotate smoothly. 160 180 0.070 0.090 1.1 1.4 2.75 3.5 0.070 0.110
clearance for both rows of rollers must be measured Items to be checked include sticking due to foreign 180 200 0.080 0.100 1.3 1.6 3.25 4.0 0.070 0.110
simultaneously, and these two values should be kept matter or visible flaws, uneven torque caused by
roughly the same by adjusting the relative position of improper mounting or an improper mounting surface, 200 225 0.090 0.110 1.4 1.7 3.5 4.25 0.080 0.130
225 250 0.100 0.120 1.6 1.9 4.0 4.75 0.090 0.140
the outer and inner rings. and excessive torque caused by an inadequate 250 280 0.110 0.140 1.7 2.2 4.25 5.5 0.100 0.150
When a large bearing is mounted on a shaft, the outer clearance, mounting error, or seal friction. If there are
ring may be deformed into an oval shape by its own no abnormalities, powered operation may be started. 280 315 0.120 0.150 1.9 2.4 4.75 6.0 0.110 0.160
weight. If the clearance is measured at the lowest part 315 355 0.140 0.170 2.2 2.7 5.5 6.75 0.120 0.180
355 400 0.150 0.190 2.4 3.0 6.0 7.5 0.130 0.200
of the deformed bearing, the measured value may be
bigger than the true value. If an incorrect radial internal 400 450 0.170 0.210 2.7 3.3 6.75 8.25 0.140 0.220
clearance is obtained in this manner and the values in 450 500 0.190 0.240 3.0 3.7 7.5 9.25 0.160 0.240
Table 14.1 are used, then the interference fit may 500 560 0.210 0.270 3.4 4.3 8.5 11.0 0.170 0.270
560 630 0.230 0.300 3.7 4.8 9.25 12.0 0.200 0.310
630 710 0.260 0.330 4.2 5.3 10.5 13.0 0.220 0.330
710 800 0.280 0.370 4.5 5.9 11.5 15.0 0.240 0.390
800 900 0.310 0.410 5.0 6.6 12.5 16.5 0.280 0.430
900 1 000 0.340 0.460 5.5 7.4 14.0 18.5 0.310 0.470
1 000 1 120 0.370 0.500 5.9 8.0 15.0 20.0 0.360 0.530
Remarks The values for reduction in radial internal clearance are for bearings with CN clearance.
For bearing with C3 Clearance,the maximum values listed should be used for the reduction
in radial internal clearance.
Fig. 14.4 Mounting with Adapter Fig. 14.5 Mounting with Withdrawal Sleeve
Oil
Large machines, which cannot be turned by hand,
can be started after examination with no load, and the
power immediately cutoff and the machine allowed to
coast to a stop. Confirm that there is no abnormality
such as vibration, noise, contact of rotating parts, etc.
Powered operation should be started slowly without
load and the operation should be observed carefully
until it is determined that no abnormalities exist, then
gradually increase the speed, load, etc. to their normal
levels. Items to be checked during the test operation
a b c include the existence of abnormal noise, excessive rise
C C c c
of bearing temperature, leakage and contamination of
lubricants, etc. If any abnormality is found during the
Fig. 14.6 Mounting with Fig. 14.7 Mounting with Special Sleeve Fig. 14.8 Clearance Measurement Fig. 14.9 Measuring Clearance in Large Spherical Roller test operation, it must be stopped immediately and the
Fig. 14.6 Hydraulic Nut Fig. 14.7 and Hydraulic Pressure Fig. 14.8 of Spherical Roller Bearing Fig. 14.9 Bearing machine should be inspected. If necessary, the bearing
should be dismounted for examination.
A 118 A 119
A100-125E.indd 118-119 11/20/13 4:52:28 PM

BEARING HANDLING
Although the bearing temperature can generally be mounting, or excessive friction of the seals. 14.4 Dismounting 14.4.2 Dismounting of Bearings with Cylindrical
estimated by the temperature of the outside surface of In the case of high speed operation, an incorrect A bearing may be removed for periodic inspection or Bores
the housing, it is more desirable to directly measure selection of bearing type or lubricating method may for other reasons. If the removed bearing is to be used If the mounting design allows space to press out the
the temperature of the outer ring using oil holes for also cause an abnormal temperature rise. again or it is removed only for inspection, it should be inner ring, this is an easy and fast method. In this
access. The sound of a bearing may be checked with a noise dismounted as carefully as when it was mounted. If the case, the withdrawal force should be imposed only on
The bearing temperature should rise gradually to locater or other instruments. Abnormal conditions are bearing has a tight fit, its removal may be difficult. The the inner ring (Fig. 14.12). Withdrawal tools like those
the steady state level within one to two hours after indicated by a loud metallic sound, or other irregular means for removal should be considered in the original shown in Figs. 14.13 and 14.14 are often used.
the operation starts. If the bearing or its mounting noise, and the possible cause may include incorrect design of the adjacent parts of the machine. When
is improper, the bearing temperature may increase lubrication, poor alignment of the shaft and housing, dismounting, the procedure and sequence of removal
rapidly and become abnormally high. The cause of this or the entry of foreign matter into the bearing. The should first be studied using the machine drawing Bolt
abnormal temperature may be an excessive amount possible causes and measures for irregularities are and considering the type of mounting fit in order to
of lubricant, insufficient bearing clearance, incorrect listed in Table 14.2. perform the operation properly.
Table 14. 2 Causes of and Measures for Operating Irregularities
14.4.1 Dismounting of Outer Rings
Irregularities Possible Causes Measures In order to remove an outer ring that is tightly fitted,
first place bolts in the push-out holes in the housing
Abnormal Load Improve the fit, internal clearance, preload, position of housing at several locations on its circumference as shown in
shoulder, etc. Fig. 14.10, and remove the outer ring by uniformly
Incorrect mounting Improve the machining accuracy and alignment of shaft and housing,
tightening the bolts. These bolt holes should always
Loud Metallic be fitted with blank plugs when not being used for Plug
accuracy of mounting method.
Sound (1)
dismounting. In the case of separable bearings, such
Insufficient or improper Lubricant Replenish the lubricant or select another lubricant. as tapered roller bearings, some notches should be Fig. 14.10 Removal of Outer Ring with Dismounting Bolts
Contact of rotating parts Modify the labyrinth seal, etc. made at several positions in the housing shoulder, as
shown in Fig. 14.11, so the outer ring may be pressed
Flaws,corrosion,or scratches on Replace or clean the bearing, improve the seals, and use clean out using a dismounting tool or by tapping it.
Noise raceways lubricant.
Loud Regular
Sound Brinelling Replace the bearing and use care when handling bearings.
Flaking on raceway Replace the bearing.
Excessive clearance Improve the fit, clearance and preload.
Irregular Penetration of foreign particles Replace or clean the bearing, improve the seals, and use clean
Sound lubricant.
Flaws or flaking on balls Replace the bearing.

Fig. 14.11 Removal Notches
Excessive amount of lubricant Reduce amount of lubricant, select stiffer grease.
Insufficient or improper lubricant Replenish lubricant or select a better one.
Abnormal load Improve the fit, internal clearance, preload, position of housing
Abnormal Temperature shoulder.
Rise
Incorrect mounting Improve the machining accuracy and alignment of shaft and housing,
accuracy of mounting, or mounting method.
Creep on fitted surface, excessive seal Correct the seals, replace the bearing, correct the fitting or mounting.
friction
Brinelling Replace the bearing and use care when handling bearings.
Flaking Replace the bearing.

Vibration
(Axial runout) Incorrect mounting Correct the squareness between the shaft and housing shoulder or side
of spacer.
Penetration of foreign particles Replace or clean the bearing, improve the seals.
Leakage or
Too much lubricant, Penetration by Reduce the amount of lubricant, select a stiffer grease. Replace the Fig. 14.12 Removal of Inner Fig. 14.13 Removal of Inner Ring Using Fig. 14.14 Removal of Inner Ring Using
Discoloration of
foreign matter or abrasion chips bearing or lubricant. Clean the housing and adjacent parts. Fig. 14.1 2 Ring Using a Press Fig. 14.13 Withdrawal Tool (1) Fig. 14.14 Withdrawal Tool (2)
Lubricant
Note (1) Intermittent squeal or high-pitch noise may be heard in medium- to large-sized cylindrical roller bearings or ball
bearings that are operating under grease lubrication in low-temperature environments. Under such low-temperature
conditions, bearing temperature will not rise resulting in fatigue nor is grease performance affected. Although
intermittent squeal or high-pitch noise may occur under these conditions, the bearing is fully functional and can
continue to be used. In the event that greater noise reduction or quieter running properties are needed, please contact
your nearest NSK branch office.
A 120 A 121
A100-125E.indd 120-121 11/20/13 4:52:29 PM

BEARING HANDLING
In both cases, the claws of the tools must substantially 14.4.3 Dismounting of Bearings with Tapered Bores 14.5 Inspection of Bearings 14.5.2 Inspection and Evaluation of Bearings
engage the face of the inner ring; therefore, it is When dismounting relatively small bearings with 14.5.1 Bearing Cleaning After being thoroughly cleaned, bearings should be
advisable to consider the size of the shaft shoulder adapters, the inner ring is held by a stop fastened to examined for the condition of their raceways and
or to cut grooves in the shoulder to accommodate the When bearings are inspected, the appearance of the
the shaft and the nut is loosened several turns. This is bearings should first be recorded and the amount and external surfaces, the amount of cage wear, the
withdrawal tools (Fig. 14.14). followed by hammering on the sleeve using a suitable increase in internal clearance, and degradation of
The oil injection method is usually used for the condition of the residual lubricant should be checked.
tool as shown in Fig. 14.18. Fig. 14.16 shows one After the lubricant has been sampled for examination, tolerances. These should be carefully checked, in
withdrawal of large bearings. The withdrawal procedure for dismounting a withdrawal sleeve by addition to examination for possible damage or other
is achieved easily by mean of oil pressure applied the bearings should be cleaned. In general, light oil or
tightening the removal nut. If this procedure is difficult, kerosene may be used as a cleaning solution. abnormalities, in order to determine the possibility for
through holes in the shaft. In the case of extra wide it may be possible to drill and tap bolt holes in the nut its reuse.
bearings, the oil injection method is used together with Dismounted bearings should first be given a
and withdraw the sleeve by tightening the bolts as preliminary cleaning followed by a finishing rinse. Each In the case of small non-separable ball bearings, hold
a withdrawal tool. shown in Fig. 14.17. the bearing horizontally in one hand, and then rotate
Induction heating is used to remove the inner rings bath should be provided with a metal net to support
Large bearings may be withdrawn easily using oil the bearings in the oil without touching the sides or the outer ring to confirm that it turns smoothly.
of NU and NJ types of cylindrical roller bearings. The pressure. Fig. 14.19 illustrates the removal of a Separable bearings such as tapered roller bearings
inner rings are expanded by brief local heating, and bottom of the tank. If the bearings are rotated with
bearing by forcing oil under pressure through a hole foreign matter in them during preliminary cleaning, the may be checked by individually examining their rolling
then withdrawn (Fig. 14.15). Induction heating is also and groove in a tapered shaft to expand the inner elements and the outer ring raceway.
used to mount several bearings of these types on a raceways may be damaged. The lubricant and other
ring. The bearing may suddenly move axially when the deposits should be removed in the oil bath during the Large bearings cannot be rotated manually; however,
shaft. interference is relieved during this procedure so a stop the rolling elements, raceway surfaces, cages,
initial rough cleaning with a brush or other means.
nut is recommended for protection. Fig. 14.20 shows a After the bearing is relatively clean, it is given the and contact surface of the ribs should be carefully
withdrawal using a hydraulic nut. finishing rinse. The finishing rinse should be done examined visually. The more important a bearing is,
carefully with the bearing being rotated while immersed the more carefully it should be inspected.
in the rinsing oil. It is necessary to always keep the The determination to reuse a bearing should be made
rinsing oil clean. only after considering the degree of bearing wear,
the function of the machine, the importance of the
bearings in the machine, operating conditions, and
the time until the next inspection. However, if any of
the following defects exist, reuse is impossible and
Oil
replacement is necessary.
Inner Ring
(a) When there are cracks in the inner or outer rings,
rolling elements, or cage.
(b) When there is flaking of the raceway or rolling
elements.
Withdrawal Claw (c) When there is significant smearing of the raceway
surfaces, ribs, or rolling elements.
Fig. 14.16 Removal of Withdrawal Fig. 14.17 Removal of Withdrawal (d) When the cage is significantly worn or rivets are
Fig. 14.15 Removal of Inner Ring Using Fig. 14 .16 Sleeve Using Withdrawal Nut (1) Fig. 14.17 Sleeve Using Withdrawal Nut (2) loose.
Fig. 14. 15 Induction Heater (e) When there is rust or scoring on the raceway
surfaces or rolling elements.
(f) When there are any significant impact or brinell
traces on the raceway surfaces or rolling elements.
(g) When there is significant evidence of creep on the
bore or the periphery of the outer ring.
(h) When discoloration by heat is evident.
( i ) When significant damage to the seals or shields of
Fig. 14.20 Removal Using Hydraulic Nut grease sealed bearings has occurred.
Fig. 14.18 Removal of Adapter with Stop and Axial Pressure Fig. 14.19 Removal Using Oil Injection Hydraulic Pump
A 122 A 123
A100-125E.indd 122-123 11/20/13 4:52:29 PM

BEARING HANDLING
14.6 Maintenance and Inspection 14.6.2 Bearing Failures and Measures

14.6.1 Detecting and Correcting Irregularities In general, if rolling bearings are used correctly they Type of Failure Probable Causes Measures
In order to maintain the original performance of a will survive to their predicted fatigue life. However, they
bearing for as long as possible, proper maintenance often fail prematurely due to avoidable mistakes. Scoring
and inspection should be performed. If proper In contrast to fatigue life, this premature failure is Scoring or smearing between raceway Inadequate initial lubrication, excessively Use a softer grease and avoid rapid
procedures are used, many bearing problems can be caused by improper mounting, handling, or lubrication, and rolling surfaces. hard grease and high acceleration when acceleration.
avoided and the reliability, productivity, and operating entry of foreign matter, or abnormal heat generation. starting.
costs of the equipment containing the bearings are all For instance, the causes of rib scoring, as one
example of premature failure, may include insufficient Spiral scoring or smearing of raceway Raceway rings are not parallel and Correct the mounting, apply a preload, or
improved. It is suggested that periodic maintenance surface of thrust ball bearing. excessive speed. select another bearing type.
be done following the procedure specified. This lubrication, use of improper lubricant, faulty lubrication
periodic maintenance encompasses the supervision system, entry of foreign matter, bearing mounting
Scoring or smearing between the end face Inadequate lubrication, incorrect mounting Select proper lubricant and modify the
of operating conditions, the supply or replacement of error, excessive deflection of the shaft, or any of the rollers and guide rib. and large axial load. mounting.
lubricants, and regular periodic inspection. Items that combination of these. Thus, it is difficult to determine
should be regularly checked during operation include the real cause of some premature failures. Cracks
bearing noise, vibration, temperature, and lubrication. If all the conditions at the time of failure and previous to Crack in outer or inner ring. Excessive shock load, excessive Examine the loading conditions, modify the
If an irregularity is found during operation, the cause the time of failure are known, including the application, interference in fitting, poor surface fit of bearing and sleeve. The fillet radius
should be determined and the proper corrective actions the operating conditions, and environment; then by cylindricality, improper sleeve taper, large must be smaller than the bearing chamfer.
studying the nature of the failure and its probable fillet radius, development of thermal
should be taken after referring to Table 14.2. cracks and advancement of flaking.
If necessary, the bearing should be dismounted causes, the possibility of similar future failures can be
and examined in detail. As for the procedure for reduced. The most frequent types of bearing failure,
Crack in rolling element. Advancement of flaking, shock applied to Be carefull in handling and mounting.
dismounting and inspection, refer to Section 14.5, along with their causes and corrective actions, are Broken rib. the rib during mounting or dropped during
Inspection of Bearings. listed in Table 14.3. handling.
Fractured cage. Abnormal loading of cage due to incorrect Reduce the mounting error and review the
NSK BEARING MONITOR (Bearing Abnormality mounting and improper lubrication. lubricating method and lubricant.
Detector)
It is important during operation to detect signs of Indentations
irregularities early before damage becomes severe. Indentations in raceway in same pattern Shock load during mounting or excessive Use care in handling.
The NSK Bearing Monitor (see Page C5) is an as rolling elements. load when not rotating.
instrument that checks the condition of bearings
and gives a warning of any abnormality, or it stops Indentations in raceway and rolling Foreign matter such as metallic chips Clean the housing, improve the seals, and
elements. or sand. use a clean lubricant.
a machine automatically in order to prevent serious
trouble. In addition, it helps to improve maintenance Abnormal Wear
and reduce its cost. False brinelling (phenomenon similar to Vibration of the bearing without rotation Secure the shaft and housing, use oil as a
brinelling) during shipment or rocking motion of lubricant and reduce vibration by applying
small amplitude. a preload.
Table 14.3 Causes and Measures for Bearing Failures
Fretting Slight wear of the fitting surface. Increase interference and apply oil.
Type of Failure Probable Causes Measures
Wearing of raceway, rolling elements, rib, Penentration by foreign matter, incorrect Improve the seals, clean the housing, and
Flaking and cage. lubrication, and rust. use a clean lubricant.
Flaking of one-side of the raceway of Abnomal axial load. A loose fit should be used when mounting
Creep Insufficient interference or insufficient Modify the fit or tighten the sleeve
radial bearing. the outer ring of free-end bearings to allow
tightening of sleeve.
axial expansion of the shaft.
Seizure
Flaking of the raceway in symmetrical Out-of-roundness of the housing bore. Correct the faulty housing.
patterm. Discoloration and melting of raceway, Insufficient clearance, incorrect Review the internal clearance and bearing
rolling elements, and ribs. lubrication, or improper mounting. fit, supply an adequate amount of the
proper lubricant and improve the mounting
Flaking pattern inclined relative to the Improper muonting, deflection of shaft, Use care in mounting and centering, select
method and related parts.
raceway in radial ball bearings. Flaking inadequate tolerances for shaft and a bearing with a large clearance, and
near the edge of the raceway and rolling housing. correct the shaft and housing shoulder.
Electric Burng
surfaces in roller bearings.
Fluting or corrugations. Melting due to electric arcing. Install a ground wire to stop the flow of
Flaking of raceway with same spacing as Large shock load during mounting, rusting Use care in mounting and apply a rust electricity or insulate the beaning.
rolling elements. while bearing is out of operation for preventive when machine operation is
prolonged period. suspended for a long time. Corrosion & Rust
Rust and corrosion of fitting surfaces and Condensation of water from the air, or Use care in storing and avoid high
Premature flaking of raceway and rolling Insufficient clearance, excessive load, Select proper fit, bearing clearance, and bearing interior. fretting. temperature and high humidity, treatment
elements. improper lubrication, rust, etc. lubricant. Penetration by corrosive for rust prevention is necessary when
substance(especially varnish-gas, etc). operation is stopped for long time.
Premature flaking of duplex bearings. Excessive preload. Adjust the preload. Selection of varnish and grease.
A 124 A 125
A100-125E.indd 124-125 11/20/13 4:52:30 PM

15. TECHNICAL DATA
DEFINIONS OF SYMBOLS AND THEIR UNITS
Symbols Nomenclature Units Symbols Nomenclature Units
a Contact Ellipse Major Axis ( mm ) na Rotating Speed of Rolling Elements (min1)
b Contact Ellipse Major Axis ( mm ) nc Revolving Speed of Rolling Elements
Cr Basic Dynamic Load Rating of Radial (Cape Speed) (min1)
Bearings (N){kgf} ne Speed of Ouder Ring (min1)
C0r Basic Static Load Radial of Radial ni Speed of Inner Ring (min1)
Bearings (N){kgf}
Page
Ca Basic Dynamic Load Rating of Thrust pm Surface Pressure on Fitted Surface (MPa ){kgf/mm2}
15. 1 AXIAL DISPLACEMENT OF BEARINGS A 128 Bearings (N){kgf} P Bearing Load (N){kgf}
C0a Basic Static Load Rating of Thrust Q Rolling Element Load (N){kgf}
(1) Contact Angle and Axial Displacement of Bearings (N){kgf}
Deep Groove Ball Bearings and Angular Contact Ball Bearings A 128 re Groove Radius of Outer Ring ( mm )
d Shaft Diameter, Nominal Bearing Bore
(2) Axial Load and Axial Displacement of Tapered Roller Bearings A 128 Diameter ( mm ) ri Groove Radius of Inner Ring ( mm )
D Housing Bore Diameter, Nominal Bearing va Circumferential Speed of Rolling Element
Outside Diameter ( mm ) about Its Center (m/sec)
15. 2 FITS A 130 De Outer Ring Raceway Diameter ( mm ) vc Circumferential Speed of Rolling Element
about Beaing Center (m/sec)
Di Inner Ring Raceway Diameter ( mm )
(1) Surface Pressure, Maximum Stress on Fitted Surfaces
and Expansion or Contraction of Raceway Diameter A 130 D0 Housing Outside Diameter ( mm )
Z Number of Rolling Elements per Row
(2) Interferences or Clearances for Shafts and Inner Rings A 130 Dpw Rolling Element Pitch Diameter ( mm )
Contact Angle (when axial load is applied
on Radial Ball Bearning ( )
(3) Interferences or Clearances for Housing Bores and Dw Nominal Rolling Element Diameter ( mm )
Outer Rings A 130 0 Initial Confact Angle (Geometri) (when
e Contact Position of Tapered Roller End inner and outer rings of Angular Contact
Face with Rib ( mm ) Ball Bearings are pushed axially) ( )
15. 3 RADIAL AND AXIAL INTERNAL CLEARANCES A 132 E Modulus of Longitudinal Elasticity R Initial Contact Angle (Geometric) (when

(Bearing Steel) inner and outer rings Angular Contact
208 000 MPa{21 200 kgf/mm2 } Ball Bearing are pushed radially) ( )
(1) Radial and Axial Internal Clearances for
Single-Row Deep Groove Ball Bearings A 132 E(k) Complete elliptic integral of the 2nd kind 1/2 of Conical Angle of Roller ( )
for which the population parameter is a Relative Axial Displacement of Inner and
(2) Radial and Axial Internal Clearances for 2
( ) b
Double-Row Angular Contact Ball Bearings A 132 Outer Rings ( mm )
k= 1
a
&a Axial Internal Clearance ( mm )
f0 factor which depends on the geometry of
the bearing components and on the &d Effective Interference of Inner Ring and
15. 4 PRELOAD AND STARTING TORQUE A 134 applicable stress level Shaft ( mm )
&r Radial Internal Clearance ( mm )
(1) Axial Load and Starting Torque of f () Function of
Tapered Roller Bearings A 134 &D Effective Interference of Outer Ring and
Fa Axial Load, Preload (N){kgf}
(2) Preload and Starting Torque of Angular Contact Ball Housing ( mm )
Fr Radial Load (N){kgf}
Bearings and Double-Direction Angular Contact Thrust & De Contraction of Outer Ring Raceway
Ball Bearings A 134 h De/D
Diameter due to Fit ( mm )
& Di Expansion of Inner Ring Raceway
h0 D/D0 Diameter dus to Fit ( mm )
k d/Di
15. 5 COEFFICIENTS OF FRICTION AND OTHER BEARING DATA A 136

Load Factor
K Constant Determined by Internal Coefficient of Dynamic Friction of Rolling
(1) Bearing Types and Their Coefficients of Friction A 136 Design of Bearing Bearing
(2) Circumferential Speed of Rolling Elements L Fatigue Life when Effective Clearance is 0 e Coefficient of Friction between Roller End
about Their Centers and Bearing Center A 136 Lwe Effective Leng of Roller ( mm ) Face and Rib
(3) Radial Internal Clearance and Fatigue Life A 136 L Fatigue Life when Effective Clearance is s Coefficient of Sliding Friction
& t max Maximum Stress on Fitted Surfaces (MPa ){kgf/mm2}
m0 Distance between Centers of Curvature of
15. 6 BRANDS AND PROPERTIES OF LUBRICATING GREASES A 138 Inner and Outer Rings
ri + re Dw ( mm )
M Frictional Torque (Nmm){kgfmm}
Ms Spin Friction (Nmm){kgfmm}
A 126 A 127
A126-141E.indd 126-127 11/20/13 4:53:03 PM

TECHNICAL DATA
15. 1 Axial Displacement of Bearings 35

0=30
C
,22
mm
(1) Contact Angle and Axial Displacement a of
0C
06C
25
C,2
30 B
00
A
10C
00
Deep Groove Ball Bearing and Angular Contact 72
18
03B 04B
4C
A
02
72
Ball Bearings 20
720
08C
14C
25 0.015
Contact Angle
(Figs. 15.1 to 15.3) 15 A
06B
C
10 04
26
1
A
0.00044 Q 2 3 20 06 08B 10B
a = sin ( ) ................... (N) 5
08
A
Axial Displacement a
Dw 0 A
10 2A
1 (mm)
15
1 4 A ,20A,2 14B
0.010
0.002 Q 2 3 18A 20B
18B, B
a = sin ( Dw ) ..................... {kgf } 10
24A
26
Fa 5
Q= (N), {kgf}
Zsin 0.005
0 Digits: Bearing Bore Number
0 0.1 0.2 0.3 0.4 0.5 0.6 C 0 = 15
(2) Axial Load F a and Axial Displacement a of A 0 = 30
Fa /Cor
Tapered Roller Bearings B 0 = 40
(Fig. 15.4) Fig. 15.1 Fa /Cor and Contact Angle of
0
0 500 1000 1500 2000 2500 N
Fa0.9 ................. (N) Deep Groove and Angular
a = 0.000077 0 50 100 150 200 250 kgf
}
Contact Ball Bearings
(sin ) Z L we0.8
1.9 0.9
(mm) Axial Load Fa
0.0006 F 0.9 Fig. 15.3 Axial Load and Axial Displacement of

a = a .............. {kgf } Angular Contact Ball Bearings
(sin )1.9 Z 0.9 L we0.8
Remarks:
Actual axial displacement may vary depending on
the shaft/housing thickness, material, and fitting
interference with the bearing. Please contact NSK m
about such factors of axial displacement which are 20
not discussed in detail in this catalog.
06
s
rie
ies
m
Se
Ser
3J
es
32
03J
160
eri
HR
JS
H R3
= 0
04
2
32
0
06
08
HR
06
140 15
08
10
08
Serie
120
10 10
04
02J
0 12 14
0=
HR3
100
06
14 12
08
10 16
14
80 10 16
= 10 12 18
0 14
60 0 = 15 16 20
18 s
0= 1
0
20 DJ Serie
3
0 = 15 5 HR30 08D
40 10D
14D
20 6210
6310
0
0 500 1000 1500 2000 2500 3000 3500 N 0
0 1000 2000 3000 4000 N
0 50 100 150 200 250 300 350 0 100 200 300 400 kgf
kgf
Axial Load Fa
Axial Load Fa
Fig. 15.4 Axial Load and Axial Displacement of
Fig. 15.2 Axial Load and Axial Displacement of Tapered Roller Bearings
Deep Groove Ball Bearings
A 128 A 129
A126-141E.indd 128-129 11/20/13 4:53:04 PM

TECHNICAL DATA
15.2 Fits Table. 15. 1 Surface Pressure, Maximum Stress on Fitted

Surfaces and Expansion or Contraction
(1) Surface Pressure p m , Maximum Stress tmax kgf/mm2 MPa
MPa kgf/mm2
kgf/mm2 MPa
250 25 MPa kgf/mm2
on Fitted Surfaces and Expansion of Inner Ring Items Shaft & Inner Ring Housing & Bore & Outer Ring 5 50 10 100
400 40
200 20
Raceway Diameter & Di or Contraction of Outer 4 40
150 15 300 30
Ring Raceway Diameter & De 3 30 250 25
(Table 15.1, Figs. 15.5 and 15.6) In case of housing outside dia. D0 5 50
Surface p6 100 10 4 40 200 20
E & D (1 h2)(1 h02) 2 20
Maximum Stress t max
Maximum Stress t max

Pressure (In case of sold shaft) n6 p6 150 15
(2) Interferences or Clearances of Shafts and Inner pm = 3 30
m
pm 2 D 1 h2 h02 m5 n6
Rings (Table 15.2)
(1 k2 ) In case D0 =
E &d 50 5 100 10
Surface Pressure
Surface Pressure
k5 2 20 m5
(MPa ) pm = 1 10
40 4 k5
(3) Interferences or Clearances of Housing Bores {kgf/mm2} 2 2 E &D js5
and Outer Rings (Table 15.3) pm = (1 h2) 30 3
2 D js5
1 10 50 5
0.5 5 2 40 4
20
0.4 4
Maximum stress Maximum circumferential Maximum circumferential stress on 30 3
stress on fitted surface of 0.3 3
t max inner ring bore is
outer ring bore surface is
10 1
0.5 5
20 2
(MPa ) 2 0.4 4
1 + k2 0.2 2
{kgf/mm2} t max = pm t max = pm 0.3 3
1 k2 1 h2
5 0.5 10 1
0.1 1 0.2 2
Expansion of In case of solid shaft 20 30 50 70 100 200 300 500 mm 20 30 50 70 100 200 300 500 mm
inner ring In case D0 Nominal Bearing Bore Diameter d (Class Normal) Nominal Bearing Bore Diameter d (Class Normal)
raceway dia. 1 h02
& Di = &d . k & De = & D h
& Di (mm) 1 h2 h02 Fig. 15.5 Surface Pressure m and Maximum Stress Fig. 15.6 Surface Pressure m and Maximum Stress
Contraction of t max for Average Fitting Interference t max for Maximum Fitting Interference
outer ring In case D0 =
raceway dia. & De = & D h
& De (mm)
Remarks The modulus of longitudinal elasticity and Poisson's ratio for

the shaft and housing material are the same as those for inner
and outer rings.
Reference 1 MPa =1 N/ mm2= 0.102 kgf / mm2
Table 15. 2 Interferences or Clearances of Shafts and Inner Rings

Units : m
Single Plane Interferences or Clearances for Each Fitting Class
Size Mean Bore Size
Classification Dia. Deviation f6 g5 g6 h5 h6 js5 j5 js6 j6 k5 k6 m5 m6 n6 p6 r6 Classification
(mm) (Normal) (mm)
& d mp Clearance Inter- Clearance Inter- Clearance Inter- Clearance Inter- Clearance Inter- Clearance Inter-
Clearance ference Inter- Clearance Inter- Interference
Clearance ference Interference Interference Interference Interference Interference Interference
ference ference ference ference ference ference
over incl. high low max. min. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. min. max. min. max. min. max. min. max. min. max. min. max. min. max. over incl.
3 6 0 8 18 2 9 4 12 4 5 8 8 8 3 6
6 10 0 8 22 5 11 3 14 3 6 8 9 8 3 11 2 12 4.5 12.5 2 15 6 10
10 18 0 8 27 8 14 2 17 2 8 8 11 8 4 12 3 13 5.5 13.5 3 16 10 18
18 30 0 10 33 10 16 3 20 3 9 10 13 10 4.5 14.5 4 15 6.5 16.5 4 19 2 21 2 25 18 30

30 50 0 12 41 13 20 3 25 3 11 12 16 12 5.5 17.5 5 18 8 20 5 23 2 25 2 30 9 32 9 37 30 50
50 65 0 15 49 15 23 5 29 5 13 15 19 15 6.5 21.5 7 21 9.5 24.5 7 27 2 30 2 36 11 39 11 45 50 65
65 80 0 15 49 15 23 5 29 5 13 15 19 15 6.5 21.5 7 21 9.5 24.5 7 27 2 30 2 36 11 39 11 45 20 54 65 80

80 100 0 20 58 16 27 8 34 8 15 20 22 20 7.5 27.5 9 26 11 31 9 33 3 38 3 45 13 48 13 55 23 65 37 79 80 100
100 120 0 20 58 16 27 8 34 8 15 20 22 20 7.5 27.5 9 26 11 31 9 33 3 38 3 45 13 48 13 55 23 65 37 79 100 120
120 140 0 25 68 18 32 11 39 11 18 25 25 25 9 34 11 32 12.5 37.5 11 39 3 46 3 53 15 58 15 65 27 77 43 93 63 113 120 140

140 160 0 25 68 18 32 11 39 11 18 25 25 25 9 34 11 32 12.5 37.5 11 39 3 46 3 53 15 58 15 65 27 77 43 93 65 115 140 160
160 180 0 25 68 18 32 11 39 11 18 25 25 25 9 34 11 32 12.5 37.5 11 39 3 46 3 53 15 58 15 65 27 77 43 93 68 118 160 180
180 200 0 30 79 20 35 15 44 15 20 30 29 30 10 40 13 37 14.5 44.5 13 46 4 54 4 63 17 67 17 76 31 90 50 109 77 136 180 200

200 225 0 30 79 20 35 15 44 15 20 30 29 30 10 40 13 37 14.5 44.5 13 46 4 54 4 63 17 67 17 76 31 90 50 109 80 139 200 225
225 250 0 30 79 20 35 15 44 15 20 30 29 30 10 40 13 37 14.5 44.5 13 46 4 54 4 63 17 67 17 76 31 90 50 109 84 143 225 250
250 280 0 35 88 21 40 18 49 18 23 35 32 35 11.5 46.5 16 42 16 51 16 51 4 62 4 71 20 78 20 87 34 101 56 123 94 161 250 280

280 315 0 35 88 21 40 18 49 18 23 35 32 35 11.5 46.5 16 42 16 51 16 51 4 62 4 71 20 78 20 87 34 101 56 123 98 165 280 315
315 355 0 40 98 22 43 22 54 22 25 40 36 40 12.5 52.5 18 47 18 58 18 58 4 69 4 80 21 86 21 97 37 113 62 138 108 184 315 355
355 400 0 40 98 22 43 22 54 22 25 40 36 40 12.5 52.5 18 47 18 58 18 58 4 69 4 80 21 86 21 97 37 113 62 138 114 190 355 400
400 450 0 45 108 23 47 25 60 25 27 45 40 45 13.5 58.5 20 52 20 65 20 65 5 77 5 90 23 95 23 108 40 125 68 153 126 211 400 450
450 500 0 45 108 23 47 25 60 25 27 45 40 45 13.5 58.5 20 52 20 65 20 65 5 77 5 90 23 95 23 108 40 125 68 153 132 217 450 500
Remarks 1. The figures for tolerance classes where stress caused by the fitting of the shaft and inner ring becomes
excessive are omitted.
2. The tolerance range js is now recommended instead of j.
A 130 A 131
A126-141E.indd 130-131 11/20/13 4:53:06 PM

TECHNICAL DATA
Table 15. 3 Interferences or Clearances of Housing Bores and Outer Rings

Units : m
Single Plane Interferences or Clearances for Each Fitting Class
Size Mean O. D. Size
Classification Deviation G7 H6 H7 H8 J6 JS6 J7 JS7 K6 K7 M6 M7 N6 N7 P6 P7 Classification
(mm) (Normal) (mm)
& D mp Clearance Clearance Clearance Clearance Inter- Clearance Inter- Clearance Inter-
Clearance ference Inter- Clearance Inter- Clearance Inter- Clearance Inter- Clearance Inter- Clearance Inter- Clearance Inter- Interference
Clearance ference Interference
ference ference ference ference ference ference ference ference
over incl. high low max. min. max. min. max. min. max. min. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. max. min. max. over incl.
6 10 0 8 28 5 17 0 23 0 30 0 13 4 12.5 4.5 16 7 15 7 10 7 13 10 5 12 8 15 1 16 4 19 4 21 1 24 6 10
10 18 0 8 32 6 19 0 26 0 35 0 14 5 13.5 5.5 18 8 17 9 10 9 14 12 4 15 8 18 1 20 3 23 7 26 3 29 10 18
18 30 0 9 37 7 22 0 30 0 42 0 17 5 15.5 6.5 21 9 19 10 11 11 15 15 5 17 9 21 2 24 2 28 9 31 5 35 18 30
30 50 0 11 45 9 27 0 36 0 50 0 21 6 19 8 25 11 23 12 14 13 18 18 7 20 11 25 1 28 3 33 10 37 6 42 30 50
50 80 0 13 53 10 32 0 43 0 59 0 26 6 22.5 9.5 31 12 28 15 17 15 22 21 8 24 13 30 1 33 4 39 13 45 8 51 50 80
80 120 0 15 62 12 37 0 50 0 69 0 31 6 26 11 37 13 32 17 19 18 25 25 9 28 15 35 1 38 5 45 15 52 9 59 80 120
120 150 0 18 72 14 43 0 58 0 81 0 36 7 30.5 12.5 44 14 38 20 22 21 30 28 10 33 18 40 2 45 6 52 18 61 10 68 120 150

150 180 0 25 79 14 50 0 65 0 88 0 43 7 37.5 12.5 51 14 45 20 29 21 37 28 17 33 25 40 5 45 13 52 11 61 3 68 150 180
180 250 0 30 91 15 59 0 76 0 102 0 52 7 44.5 14.5 60 16 53 23 35 24 43 33 22 37 30 46 8 51 16 60 11 70 3 79 180 250
250 315 0 35 104 17 67 0 87 0 116 0 60 7 51 16 71 16 61 26 40 27 51 36 26 41 35 52 10 57 21 66 12 79 1 88 250 315

315 400 0 40 115 18 76 0 97 0 129 0 69 7 58 18 79 18 68 28 47 29 57 40 30 46 40 57 14 62 24 73 11 87 1 98 315 400
400 500 0 45 128 20 85 0 108 0 142 0 78 7 65 20 88 20 76 31 53 32 63 45 35 50 45 63 18 67 28 80 10 95 0 108 400 500
500 630 0 50 142 22 94 0 120 0 160 0 72 22 85 35 50 44 50 70 24 70 24 96 6 88 6 114 28 122 28 148 500 630
630 800 0 75 179 24 125 0 155 0 200 0 100 25 115 40 75 50 75 80 45 80 45 110 25 100 25 130 13 138 13 168 630 800
800 1 000 0 100 216 26 156 0 190 0 240 0 128 28 145 45 100 56 100 90 66 90 66 124 44 112 44 146 0 156 0 190 800 1 000
Note () Indicates the minimum interference

Remarks The tolerance range JS is now recommended instead of J.
15.3 Radial and Axial Internal Table 15. 4 Constant K

Clearances mm
(1) Radial Internal Clearance & r and Axial Values of K
1.00
Internal Clearance & a in Single-Row Bore No. 160XX 60XX 62XX 63XX 63Series
28, 30
Deep Groove Ball Bearings 00 0.93 1.14
62Series 22, 24
(Fig. 15.7) 01 0.80 0.80 0.93 1.06 0.50
24~30
21, 22
17~19
15, 16
1 02 0.80 0.93 0.93 1.06 16, 17 10, 11
13~15
& aHK & r 2 (mm)
Axial Internal Clearance & a

03 0.80 0.93 0.99 1.11 10~11 07
04 0.90 0.96 1.06 1.07 0.30 07 05, 06 m
04~06 01~04
where 05 0.90 0.96 1.06 1.20 00~02
Axial Internal Clearance & a

0.20 80

25
1 06 0.96 1.01 1.07 1.19
ot
K = 2 (re + r i Dw) 07 0.96 1.06 1.25 1.37
rc
2
&
08 0.96 1.06 1.29 1.45 5320
a=
60
&
09 1.01 1.11 1.29 1.57 0.10 5315
(2) Radial Internal Clearance & r and Axial 10 1.01 1.11 1.33 1.64 5310
Internal Clearance & a in Double-Row 11 1.06 1.20 1.40 1.70 160Series 60Series 5220 5305
22~28 40
Angular Contact Ball Bearings 12 1.06 1.20 1.50 2.09
0.05
26~30
21~24
21
16~17
5215
(Fig. 15.8) 13 1.06 1.20 1.54 1.82 5205 5210
16~17 11~13
14 1.16 1.29 1.57 1.88 0.04 11~13 07~10
5200
20
06~08 02~05

2 15 1.16 1.29 1.57 1.95 0.03
m 0 m 0 cos R r
&
&a = 2 2
( 2
) 16
17
1.20
1.20
1.37
1.37
1.64
1.70
2.01
2.06
01~03 01
0
0.02
2 m 0 sin R (mm) 18 1.29 1.44 1.76 2.11 0.001 0.003 0.005 0.01 0.02 0.03 0.05 0.1 0.2 0 10 20 30 40
m
50
19 1.29 1.44 1.82 2.16 Radial Internal Clearance & r mm Radial Internal Clearance & r
20 1.29 1.44 1.88 2.25
21 1.37 1.54 1.95 2.32 Fig. 15.7 & r and & a in Single-Row Deep Groove Ball Bearings Fig. 15.8 & r and & a in Double-Row Angular
22 1.40 1.64 2.01 2.40 Contact Ball Bearings (52, 53 Series)
24 1.40 1.64 2.06 2.40
26 1.54 1.70 2.11 2.49
28 1.54 1.70 2.11 2.59
30 1.57 1.76 2.11 2.59
A 132 A 133
A126-141E.indd 132-133 11/20/13 4:53:07 PM

TECHNICAL DATA
15. 4 Preload and Staring Torque (2) Preload Fa and Starting Torque M of Angular kgf . mm N . mm
(1) Axial Load Fa and Starting Torque M of Tapered Contact Ball Bearings and Double-Direction 30 300
Roller Bearings (Figs. 15.9 and 15.10) Angular Contact Thrust Ball Bearings (Figs. 15.11
and 15.12)
M = e e Fa cos (Nmm), {kgfmm}
M = Ms Z sin (Nmm), {kgfmm}
Starting Torque of Duplex Bearings

where
where Ms is spin friction 200
e : 0.20 3
20
When bearings with the same number are used in Ms = s Q a E(k) (Nmm), {kgfmm} 20
16 ,10
8 22
8 08
(for two bearings) 2M

opposition, the torque M caused by the preload 1 4
,1
becomes 2M. 12 06
where
04 02 00
Dw1 s = 0.15 10 100 Ser
ies
F When bearings with the same number are used in 72C
Qe 22 20 0
opposition, the torque M caused by the preload 14 1
L 00 ries
e Qf e becomes 2M. Se
Qf 70C
2 Qi 0
0
0 500 1000 1500 2000 N
0
0 50 100 150 200 kgf
Fig. 15.9 Relation between e and
Preload Fa
Fig. 15.11 Preload and Starting Torque for Back-to-Back or Face-to-Face Arrangements
of Angular Contact Ball Bearings ( =15)
kgfmm Nmm
5000
500
kgf . mm N . mm
4000 14 70 700
400 12
10 600
18 60 280TAC20
240TAC20
3000 08
200TAC20
Starting Torque M
300 ,16 500

14
D 14 150TAC20
06 50
Starting Torque M
12
16
100TAC20
D 10
14 12 80TAC20
04 400
2000 10
D 40 60TAC20
200 10 06 s
rie
Se 50TAC20
08 s 3J
rie 3 2 40TAC20
18 08D Se HR
300
06 2J 30 240TAC29
s 32
04 rie HR 170TAC29
14 Se
100 1000 ies DJ 140TAC29
08 s S er 30
3
20 200
rie 3J HR 120TAC29
Se 30
06 2J HR 100TAC29
R30
H 80TAC29
10 100
60TAC29
0 0
0 5000 10000 15000 N
0 0
0 500 1000 1500 kgf 0 1000 2000 3000 4000 5000 6000 7000 8000 9000 N
Axial Load Fa 0 100 200 300 400 500 600 700 800 900 kgf
Fig. 15.10 Relation between Axial Load and Starting Preload Fa
Torque of Tapered Roller Bearings
Fig. 15.12 Preload and Starting Torque of Double-Direction
Angular Contact Thrust Ball Bearings
A 134 A 135
A126-141E.indd 134-135 11/20/13 4:53:08 PM

TECHNICAL DATA
15.5 Coefficients of Dynamic Friction and (3) Radial Internal Clearance & r and Fatigue Life L Table 15. 7 and f ( ), L /L
Other Bearing Data (Fig. 15.13)
Deep Groove Ball Bearings Cylindrical Roller Bearings
(1) Bearing Types and Their Coefficients of Dynamic For the radial internal clearance & r and the function f

Friction () of the load factor, the following equations are valid: f ()
L
f ()
L

L L
For Deep Groove Ball Bearings
= M 0.1
0.2
33.713
10.221
0.294
0.546
51.315
14.500
0.220
0.469
P
d &r D
1
0.3 4.045 0.737 5.539 0.691
w 3
2 f ( ) = 2
....................................(N) 0.4 1.408 0.889 1.887 0.870
Table 15.5 Coefficients of Dynamic Friction

0.00044 Fr
Z ( ) 3 0.5
0.6
0
0.859
1.0
1.069
0
1.133
1.0
1.075
1
& r Dw 3 0.7 1.438 1.098 1.897 1.096
Bearing Types Approximate values of f ( ) = 2
....................................{kgf} 0.8 1.862 1.094 2.455 1.065
Deep Groove Ball Bearings
Angular Contact Ball Bearings
0.0013
0.0015
0.002 Fr
Z ( ) 3 0.9
1.0
2.195
2.489
1.041
0.948
2.929
3.453
0.968
0.805
1.25 3.207 0.605 4.934 0.378
Self-Aligning Ball Bearings 0.0010 1.5 3.877 0.371 6.387 0.196
Thrust Ball Bearings 0.0011 For Cylindrical Roller Bearings
1.67 4.283 0.276 7.335 0.133
& r L we0.8 4.596 8.082
Cylindrical Roller Bearings 0.0010 f ( ) = 0.9
..................................(N) 1.8
2.0 5.052
0.221
0.159 9.187
0.100
0.067
Tapered Roller Bearings
Spherical Roller Bearings
0.0022
0.0028
0.000077 ( FZ ) r
2.5
3
6.114
7.092
0.078
0.043
11.904
14.570
0.029
0.015
Needle Roller Bearings & r L we 0.8 4 8.874 0.017 19.721 0.005
with Cages 0.0015 f ( ) = 0.9 ..................................{kgf}
Full Complement Needle
Roller Bearings 0.0025
0.0006 Fr
Z ( ) 5
10
10.489
17.148
0.008
0.001
24.903
48.395
0.002
0.0002
Spherical Thrust Roller

0.0028 The relation between the load factor and f ( ) and
Bearings L / L , when the radial internal clearance is & r is as
shown in Table 15.7.
From the above equations, first obtain f ( ) and then
and L / L can be obtained.
(2) Circumferential Speeds of Rolling Elements

about Their Centers and Bearing Center
1.0
P=Cr/5 6208
Table 15.6 Circumferential Speeds of Rolling Elements about P=Cr/10 Cr=29 100 N
Their Centers and Bearing Center 0.8 P=Cr/15
L
L
Life Ratio
Items Rotating inner ring, fixed outer ring Rotating outer ring, fixed inner ring
0.6
cos2 n i cos2 n e
Ball rotating speed
na (min1)
(
Dpw
Dw

Dpw/Dw 2 ) + ( DD pw
w

Dpw/Dw 2 )
0.4
Cicumferential
cos2 n i cos2 n e
Dw + Dw

speed around
bearing ball's center 60 10
3
Dpw
(D w Dpw/Dw
)2 3
Dpw
60 10
(D w Dpw/Dw
)2 0.2 NU208 P=Cr/5
a (m/sec) Cr=43 500 N P=Cr/10
Revolving P=Cr/15
cos n i cos n e
speed around
bearing center
+ 1( Dpw/Dw 2 ) (
+ 1
Dpw/Dw 2 ) 60 40 20 0 20 40 60 80 100 120
nc (min1) m
Radial Internal Clearance & r
Cicumferential
cos cos n e
Dpw 1 + Dpw 1
ni
speed around
bearing center 60 10
3 ( Dpw/Dw
)2 60 10
3 ( Dpw/Dw
)2 Fig. 15.13 Radial Internal Clearance and Life Ratio
c (m/sec)
Remarks 1. + sign indicates CW rotation and sign CCW
Remarks 2. The revolving speed and circumferential speed of the rolling elements are the same as those of the
cage.
A 136 A 137
A126-141E.indd 136-137 11/20/13 4:53:09 PM

TECHNICAL DATA
15. 6 BRANDS AND PROPERTIES OF LUBRICATING GREASES

Table 15. 8 Brands of Lubricating Greases and Comparison of Properties
Working Usable Limit Compared

Brands Thickeners Base Oils Dropping Point (C) Consistency Temperature Pressure Resistance to Listed Limiting
Range(1)(C) Speed(2)(%)
ADLEX Lithium Mineral oil 198 300 0 to +110 Good 70
APOLOIL AUTOLEX A Lithium Mineral oil 198 280 10 to +110 Fair 60

ARAPEN RB 300 Lithium/Calcium Mineral oil 177 294 10 to + 80 Fair 70
EA2 GREASE Urea (3) Poly--olefin oil 260 243 40 to +150 Fair 100
EA5 GREASE Urea (3) Poly--olefin oil 260 251 40 to +160 Good 60
ENC GREASE Urea (3) Polyol ester oil + Mineral oil (4) 260 262 40 to +160 Fair 70
ENS GREASE Urea (3) Polyol ester oil (4) 260 264 40 to +160 Poor 100
ECE GREASE Lithium Poly--olefin oil 260 235 10 to +120 Fair 100
ISOFLEX NBU 15 Barium Complex Ester oil + Mineral oil (4) 260 280 30 to +120 Poor 100
ISOFLEX SUPER LDS 18 Lithium Ester oil (4) 195 280 50 to +110 Poor 100
ISOFLEX TOPAS NB 52 Barium Complex Poly--olefin oil 260 280 40 to +130 Poor 90
DOW CORNING SH 33 L GREASE Lithium Silicone oil (5) 210 310 60 to +120 Poor 60
DOW CORNING SH 44 M GREASE Lithium Silicone oil (5) 210 260 30 to +130 Poor 60
NS HI-LUBE Lithium Polyol ester oil + Diester oil (4) 192 250 40 to +130 Fair 100
NSC GREASE Lithium Alkyldiphenyl ether oil + Polyol ester oil (4) 192 235 30 to +140 Fair 70
NSK CLEAN GREASE LG2 Lithium Poly--olefin oil + Mineral oil 201 199 40 to +130 Poor 100
EMALUBE 8030 Urea (3) Mineral oil 260 280 0 to +130 Good 60
MA8 GREASE Urea (3) Alkyldiphenyl ether oil + Poly--olefin oil 260 283 30 to +160 Fair 70
KRYTOX GPL-524 PTFE Perfluoropolyether oil 260 265 0 to +200 Fair 70

KP1 GREASE PTFE Perfluoropolyether oil 260 280 30 to +200 Fair 60
COSMO WIDE GREASE WR No.3N Sodium Terephtalamate Polyol ester oil + Mineral oil (4) 230 227 40 to +130 Poor 100
G-40M Lithium Silicone oil (5) 223 252 30 to +130 Poor 60
SHELL GADUS S2 V220 2 Lithium Mineral oil 187 276 0 to + 80 Good 60

SHELL ALVANIA GREASE S1 Lithium Mineral oil 182 323 10 to +110 Fair 70
CASSIDA GREASE RLS 2 Aluminum Complex Poly--olefin oil 240 280 0 to +120 Fair 70
SHELL SUNLIGHT GREASE 2 Lithium Mineral oil 200 274 10 to +110 Fair 70
WPH GREASE Urea (3) Poly--olefin oil 259 240 40 to +150 Fair 70
DEMNUM GREASE L-200 PTFE Perfluoropolyether oil 260 280 30 to +200 Fair 60
NIGACE WR-S Urea (3) Synthetic oil 260 230 30 to +150 Poor 70
NIGLUBE RSH Sodium Complex Polyalkylene Glycol oil 260 270 20 to +120 Fair 60
Notes (1) If grease will be used at the upper or lower limit sufficient of the temperature range or in a special environment such (continued on next page)
as vacuum, it is advisable to consult NSK.
Notes (2) For short-term operation or when cooling is grease may be used at speeds exceeding the above limits provided the
supply of grease is appropriate.
Notes (3) Urea-based grease causes fluorine-based material to deteriorate.
Notes (4) Ester-based grease causes acrylic rubber material to swell.
Notes (5) Silicone-based grease causes silicone-based material to swell.
A 138 A 139
A126-141E.indd 138-139 11/20/13 4:53:10 PM

TECHNICAL DATA
Working Usable Limit Compared

Brands Thickeners Base Oils Dropping Point (C) Consistency Temperature Pressure Resistance to Listed Limiting
Range(1)(C) Speed(2)(%)
PALMAX RBG Lithium Complex Mineral oil 216 300 10 to +130 Good 70
BEACON 325 Lithium Diester oil (4) 190 274 50 to +100 Poor 100
MULTEMP PS No.2 Lithium Poly--olefin oil + Diester oil (4) 190 275 50 to +110 Poor 100
MOLYKOTE FS-3451 GREASE PTFE Fluorosilicone oil (5) 260 285 0 to +180 Fair 70
UME GREASE Urea Mineral oil 260 268 10 to +130 Fair 70

RAREMAX AF-1 Urea Mineral oil 260 300 10 to +130 Fair 70
Notes (1) If grease will be used at the upper or lower limit sufficient of the temperature range or in a special environment such
as vacuum, it is advisable to consult NSK.
Notes (2) For short-term operation or when cooling is grease may be used at speeds exceeding the above limits provided the
supply of grease is appropriate.
Notes (3) Urea-based grease causes fluorine-based material to deteriorate.
Notes (4) Ester-based grease causes acrylic rubber material to swell.
Notes (5) Silicone-based grease causes silicone-based material to swell.
A 140 A 141
A126-141E.indd 140-141 11/20/13 4:53:11 PM

BEARING TABLES
B001-029E.indd 1 11/20/13 4:53:34 PM

BEARING TABLE CONTENTS Page
BALL BEARING UNITS B280

Page SET SCREW TYPE
DEEP GROOVE BALL BEARINGS B4 Shaft Dia.
Bore Dia. Pillow blocks cast housing
SINGLE-ROW DEEP GROOVE BALL BEARINGS 10 800mm B8 UCP2 12 90mm B286
MAXIMUM TYPE BALL BEARINGS 25 110mm B26 Flanged units cast housing
MAGNETO BEARINGS 4 20mm B28 UCF2 12 90mm B292
EXTRA SMALL BALL BEARINGS AND UCFL2 12 90mm B298
MINIATURE BALL BEARINGS B30
Metric Design 1 9mm B34 PLUMMER BLOCKS B304
Inch Design 1.016 9.525mm B42 Shaft Dia.
STANDARD TYPE PLUMMER BLOCKS 20 140mm B306
ANGULAR CONTACT BALL BEARINGS B46 LARGE PLUMMER BLOCKS 150 450mm B312
Bore Dia. DUSTPROOF PLUMMER BLOCKS 50 180mm B316
SINGLE-ROW ANGULAR CONTACT BALL BEARINGS 10 200mm B50 STEPPED-SHAFT TYPE PLUMMER BLOCKS 25 320mm B318
MATCHED ANGULAR CONTACT BALL BEARINGS 10 200mm B50
DOUBLE-ROW ANGULAR CONTACT BALL BEARINGS 10 85mm B70 CYLINDRICAL ROLLER BEARINGS FOR SHEAVES B326
FOUR-POINT CONTACT BALL BEARINGS 30 200mm B72 Bore Dia.
Open Type 50 560mm B328
SELF-ALIGNING BALL BEARINGS B76 Prelubricated Type 40 400mm B332
Bore Dia.
SELF-ALIGNING BALL BEARINGS 5 110mm B78 ROLL-NECK BEARINGS B334
Bore Dia.
CYLINDRICAL ROLLER BEARINGS B84 FOUR-ROW TAPERED ROLLER BEARINGS 100 939.800mm B338
Bore Dia. FOUR-ROW CYLINDRICAL ROLLER BEARINGS 100 920mm B340
SINGLE-ROW CYLINDRICAL ROLLER BEARINGS 20 500mm B88
L-SHAPED THRUST COLLARS FOR CYLINDRICAL ROLLER RAILWAY ROLLING STOCK BEARINGS B344
BEARINGS 20 320mm B104
DOUBLE-ROW CYLINDRICAL ROLLER BEARINGS 25 360mm B106 ROLLING ELEMENTS B346
Basic Dia.
TAPERED ROLLER BEARINGS B110 STEEL BALLS FOR BALL BEARINGS 0.3 114.3mm B348
Bore Dia. CYLINDRICAL ROLLERS FOR ROLLER BEARINGS 3 80mm B350
METRIC DESIGN TAPERED ROLLER BEARINGS 15 440mm B116 LONG CYLINDRICAL ROLLERS FOR ROLLER BEARINGS 5.5 15mm B352
INCH DESIGN TAPERED ROLLER BEARINGS 12.000 206.375mm B136 NEEDLE ROLLERS FOR ROLLER BEARINGS 1 5mm B354
DOUBLE-ROW TAPERED ROLLER BEARINGS 80 260mm B172
ACCESSORIES FOR ROLLING BEARINGS B356
SPHERICAL ROLLER BEARINGS B182 Shaft Dia.
Bore Dia. ADAPTERS FOR ROLLING BEARINGS 17 470mm B358
SPHERICAL ROLLER BEARINGS 25 1400mm B184 WITHDRAWAL SLEEVES FOR ROLLING BEARINGS 35 480mm B366
NUTS FOR ROLLING BEARINGS B372
THRUST BEARINGS B206 STOPPERS FOR ROLLING BEARINGS B377
Bore Dia. LOCK-WASHERS FOR ROLLING BEARINGS B378
SINGLE-DIRECTION THRUST BALL BEARINGS 10 360mm B210
DOUBLE-DIRECTION THRUST BALL BEARINGS 10 190mm B218
CYLINDRICAL ROLLER THRUST BEARINGS 35 320mm B224
SPHERICAL THRUST ROLLER BEARINGS 60 500mm B228
ANGULAR CONTACT THRUST BALL BEARINGS B234
Double-Direction Angular Contact Thrust Ball Bearings 35 280mm B238
Angular Contact Thrust Ball Bearings for Ball Screws 15 60mm B242
Needle Roller Bearings B244

Bore Dia.
CAGE & NEEDLE ROLLER ASSEMBLIES 5 100mm B252
DRAWN CUP NEEDLE ROLLER BEARINGS 4 55mm B258
SOLID NEEDLE ROLLER BEARINGS 9 390mm B264
THRUST NEEDLE ROLLER BEARINGS 10 100mm B274
CAM FOLLOWERS 16 90mm B276
ROLLER FOLLOWERS 5 50mm B278
B2 B3
B001-029E.indd 2-3 11/20/13 4:53:35 PM

DEEP GROOVE BALL BEARINGS
SINGLE-ROW DEEP GROOVE BALL BEARINGS
Open Type, Shielded Type, Sealed Type Bore Diameter 10 240mm B8
Open Type Bore Diameter 260 800mm B20
MAXIMUM TYPE BALL BEARINGS Bore Diameter 25 11Omm B26
MAGNETO BEARINGS Bore Diameter 4 20mm B28
Extra Small and Miniature Ball Bearings are described on Pages B30 to B45.
DESIGN, TYPES, AND FEATURES

Single-Row Deep Groove Ball Bearings are classified into the types shown
below.
The proper amount of good quality grease is packed in shielded and sealed
ball bearings. A comparison of the features of each type is shown in Table 1.
Table 1 Features of Sealed Ball Bearings
Type Shielded Type Non-Contact Contact Rubber Sealed Type

(ZZ Type) Rubber Sealed Type (DDU Type)
(VV Type)
Torque Low Low Higher than ZZ, VV types

Open Type With Snap Ring due to contact seal
Speed Good Good Limited by contact seals

capability
Grease sealing Good Better than ZZ type A little better than VV type
effectiveness
Dust Good Better than ZZ type Best (usable even in very

resistance (usable in dusty environment)
Shielded Type Non-Contact
moderately dusty
(ZZ Type) Rubber Sealed environment)
Type (VV Type)
Water Not Not suitable Good (usable even if fluid is
resistance suitable splashed on bearing)
Operating 10 to 10 to +110C 10 to +100C

temperature (1) +110C
Note (1) The above temperature range applies to standard bearings. By using
Contact cold or heat resistant grease and changing the type of rubber, the
Rubber Sealed operating temperature range can be extended. For such applications,
Type (DDU Type) please contact NSK.
B4 B5
B001-029E.indd 4-5 11/20/13 4:53:36 PM

For deep groove ball bearings, pressed cages are usually used. For big TOLERANCES AND RUNNING ACCURACY
bearings, machined brass cages are used. (Refer to Table 2)
Machined cages are also used for high speed applications. SINGLE-ROW DEEP GROOVE BALL
BEARINGS Table 8.2 (Pages A60 to A63)
MAXIMUM TYPE BALL BEARINGS Table 8.2 (Pages A60 to A63)
Table 2 Standard Cages for Deep Groove Ball Bearings MAGNETO BEARINGS Table 8.5 (Pages A70 and A71)
Series Pressed Steel Cages Machined Brass Cages

RECOMMENDED FITS
68 6800 6838 6840 68/800
69 6900 6936 6938 69/800 SINGLE-ROW DEEP GROOVE BALL
160 16001 16026 16028 16064 BEARINGS Table 9.2 (Page A84)
60 6000 6040 6044 60/670 Table 9.4 (Page A85)
62 6200 6240 6244 6272 MAXIMUM TYPE BALL BEARINGS Table 9.2 (Page A84)
63 6300 6332 6334 6356 Table 9.4 (Page A85)
MAGNETO BEARINGS Table 9.2 (Page A84)
Table 9.4 (Page A85)
MAXIMUM TYPE BALL BEARINGS INTERNAL CLEARANCES

Maximum Type Ball Bearings contain a larger number of balls than normal deep
groove ball bearings because of filling slots in the inner and outer rings. Because SINGLE-ROW DEEP GROOVE BALL
of their filling slots, they are not suitable for applications with high axial loads. BEARINGS Table 9.9 (Page A89)
BL2 and BL3 types of bearings have boundary dimensions equal to those of
MAXIMUM TYPE BALL BEARINGS Table 9.9 (Page A89)
single-row deep groove ball bearings of Series 62 and 63 respectively. Besides the
open type, ZZ type shielded bearings are also available. MAGNETO BEARINGS Table 9.11 (Page A89)
When using these bearings, it is important for the filling slot in the outer ring to
be outside of the loaded zone as much as possible.
Their cages are pressed steel. LIMITING SPEEDS
The limiting speeds listed in the bearing tables should be adjusted depending
MAGNETO BEARINGS on the bearing load conditions. Also, higher speeds are attainable by making
The groove in the inner ring is a little shallower than that of deep groove ball changes in the lubrication method, cage design, etc. Refer to Page A37 for
bearings and one side of the outer ring is relieved. Consequently, the outer ring is detailed information.
separable, which makes it convenient for mounting.
Pressed cages are standard, but for high speed applications, machined
synthetic resin cages are used.
PRECAUTIONS FOR USE OF DEEP GROOVE BALL BEARINGS

For deep groove ball bearings, if the bearing load is too small during operation,
slippage occurs between the balls and raceways, which may result in smearing.
The higher the weight of balls and cage, the higher this tendency becomes,
especially for large bearings. If very small bearing loads are expected, please
contact NSK for selection of an appropriate bearing.
B6 B7
B001-029E.indd 6-7 11/20/13 4:53:36 PM

Dynamic Equivalent Load
Bore Diameter 10 22 mm P =X Fr +Y Fa
Fa Fa
f f 0 Fa e >e
B e Fr Fr
C 0r
rN a b r0
X Y X Y
r ra
0.172 0.19 1 0 0.56 2.30
0.345 0.22 1 0 0.56 1.99
r ra ra 0.689 0.26 1 0 0.56 1.71
1.03 0.28 1 0 0.56 1.55
jD 2 1.38 0.30 1 0 0.56 1.45
jD jd jDa jda jD X 2.07 0.34 1 0 0.56 1.31
3.45 0.38 1 0 0.56 1.15
5.17 0.42 1 0 0.56 1.04
jD 1 6.89 0.44 1 0 0.56 1.00
Static Equivalent Load
Fa
>0.8, P0 =0.6Fr +0.5Fa
Fr
Open Type Shielded Type Non-Contact Contact With Snap With CY
Fa
ZZ Sealed Type Sealed Type Ring Groove Snap Ring 0.8, P0 =Fr
VV DD DDU N NR Fr
Boundary Dimensions Basic Load Ratings Factor Limiting Speeds (min 1) Snap Ring Groove Dimensions (1) Snap Ring (1) Abutment and Fillet Dimensions Mass
Bearing Numbers
(mm) (N) {kgf} With With (mm) Dimensions (mm) (kg)
Grease Oil Snap Snap (mm)
d D B r Cr C 0r Cr C 0r f0 Open
Z ZZ DU Open Open Shielded Sealed Ring Ring a b D1 r0 rN D2 f d a(2) D a(2) ra Dx CY
min. V VV DDU Z Groove max. min. max. max. min. max. max. min. max. max. max. min. max. approx.
10 19 5 0.3 1 720 840 175 86 14.8 34 000 24 000 40 000 6800 ZZ VV DD 12 12 17 0.3 0.005
22 6 0.3 2 700 1 270 275 129 14.0 32 000 22 000 38 000 6900 ZZ VV DD N( 3) NR( 3) 1.05 0.80 20.80 0.20 0.2 24.8 0.70 12 12.5 20 0.3 25.5 1.5 0.009
26 8 0.3 4 550 1 970 465 201 12.4 30 000 22 000 36 000 6000 ZZ VV DDU N( 4) NR( 4) 1.35 0.87 24.50 0.20 0.3 28.7 0.84 12 13 24 0.3 29.4 1.9 0.018
30 9 0.6 5 100 2 390 520 244 13.2 24 000 18 000 30 000 6200 ZZ VV DDU N NR 2.06 1.35 28.17 0.40 0.5 34.7 1.12 14 16 26 0.6 35.5 2.9 0.032
35 11 0.6 8 100 3 450 825 350 11.2 22 000 17 000 26 000 6300 ZZ VV DDU N NR 2.06 1.35 33.17 0.40 0.5 39.7 1.12 14 16.5 31 0.6 40.5 2.9 0.052
12 21 5 0.3 1 920 1 040 195 106 15.3 32 000 20 000 38 000 6801 ZZ VV DD 14 14 19 0.3 0.006
24 6 0.3 2 890 1 460 295 149 14.5 30 000 20 000 36 000 6901 ZZ VV DD N( 3) NR( 3) 1.05 0.80 22.80 0.20 0.2 26.8 0.70 14 14.5 22 0.3 27.5 1.5 0.010
28 7 0.3 5 100 2 370 520 241 13.0 28 000 32 000 16001 14 26 0.3 0.019
28 8 0.3 5 100 2 370 520 241 13.0 28 000 18 000 32 000 6001 ZZ VV DDU N( 4) NR( 4) 1.35 0.87 26.50 0.20 0.3 30.7 0.84 14 15.5 26 0.3 31.4 1.9 0.022
32 10 0.6 6 800 3 050 695 310 12.3 22 000 17 000 28 000 6201 ZZ VV DDU N NR 2.06 1.35 30.15 0.40 0.5 36.7 1.12 16 17 28 0.6 37.5 2.9 0.037
37 12 1 9 700 4 200 990 425 11.1 20 000 16 000 24 000 6301 ZZ VV DDU N NR 2.06 1.35 34.77 0.40 0.5 41.3 1.12 17 18 32 1 42 2.9 0.060
15 24 5 0.3 2 070 1 260 212 128 15.8 28 000 17 000 34 000 6802 ZZ VV DD 17 17 22 0.3 0.007
28 7 0.3 4 350 2 260 440 230 14.3 26 000 17 000 30 000 6902 ZZ VV DD N( 3) NR( 3) 1.30 0.95 26.70 0.25 0.3 30.8 0.85 17 17 26 0.3 31.5 1.8 0.015
32 8 0.3 5 600 2 830 570 289 13.9 24 000 28 000 16002 17 30 0.3 0.027
32 9 0.3 5 600 2 830 570 289 13.9 24 000 15 000 28 000 6002 ZZ VV DDU N NR 2.06 1.35 30.15 0.40 0.3 36.7 1.12 17 19 30 0.3 37.5 2.9 0.031
35 11 0.6 7 650 3 750 780 380 13.2 20 000 14 000 24 000 6202 ZZ VV DDU N NR 2.06 1.35 33.17 0.40 0.5 39.7 1.12 19 20.5 31 0.6 40.5 2.9 0.045
42 13 1 11 400 5 450 1 170 555 12.3 17 000 13 000 20 000 6302 ZZ VV DDU N NR 2.06 1.35 39.75 0.40 0.5 46.3 1.12 20 22.5 37 1 47 2.9 0.083
17 26 5 0.3 2 630 1 570 268 160 15.7 26 000 15 000 30 000 6803 ZZ VV DD 19 19 24 0.3 0.007
30 7 0.3 4 600 2 550 470 260 14.7 24 000 15 000 28 000 6903 ZZ VV DDU N( 3) NR( 3) 1.30 0.95 28.70 0.25 0.3 32.8 0.85 19 19.5 28 0.3 33.5 1.8 0.017
35 8 0.3 6 000 3 250 610 330 14.4 22 000 26 000 16003 19 33 0.3 0.033
35 10 0.3 6 000 3 250 610 330 14.4 22 000 13 000 26 000 6003 ZZ VV DDU N NR 2.06 1.35 33.17 0.40 0.3 39.7 1.12 19 21.5 33 0.3 40.5 2.9 0.041
40 12 0.6 9 550 4 800 975 490 13.2 17 000 12 000 20 000 6203 ZZ VV DDU N NR 2.06 1.35 38.10 0.40 0.5 44.6 1.12 21 23.5 36 0.6 45.5 2.9 0.067
47 14 1 13 600 6 650 1 390 675 12.4 15 000 11 000 18 000 6303 ZZ VV DDU N NR 2.46 1.35 44.60 0.40 0.5 52.7 1.12 22 25.5 42 1 53.5 3.3 0.113
20 32 7 0.3 4 000 2 470 410 252 15.5 22 000 13 000 26 000 6804 ZZ VV DD N NR 1.30 0.95 30.70 0.25 0.3 34.8 0.85 22 22 30 0.3 35.5 1.8 0.017
37 9 0.3 6 400 3 700 650 375 14.7 19 000 12 000 22 000 6904 ZZ VV DDU N NR 1.70 0.95 35.70 0.25 0.3 39.8 0.85 22 24 35 0.3 40.5 2.3 0.037
42 8 0.3 7 900 4 450 810 455 14.5 18 000 20 000 16004 22 40 0.3 0.048
42 12 0.6 9 400 5 000 955 510 13.8 18 000 11 000 20 000 6004 ZZ VV DDU N NR 2.06 1.35 39.75 0.40 0.5 46.3 1.12 24 25.5 38 0.6 47 2.9 0.068
47 14 1 12 800 6 600 1 300 670 13.1 15 000 11 000 18 000 6204 ZZ VV DDU N NR 2.46 1.35 44.60 0.40 0.5 52.7 1.12 25 26.5 42 1 53.5 3.3 0.107
52 15 1.1 15 900 7 900 1 620 805 12.4 14 000 10 000 17 000 6304 ZZ VV DDU N NR 2.46 1.35 49.73 0.40 0.5 57.9 1.12 26.5 28 45.5 1 58.5 3.3 0.145
22 44 12 0.6 9 400 5 050 960 515 14.0 17 000 11 000 20 000 60/22 ZZ VV DDU N NR 2.06 1.35 41.75 0.40 0.5 48.3 1.12 26 26.5 40 0.6 49 2.9 0.074
50 14 1 12 900 6 800 1 320 695 13.5 14 000 9 500 16 000 62/22 ZZ VV DDU N NR 2.46 1.35 47.60 0.40 0.5 55.7 1.12 27 29.5 45 1 56.5 3.3 0.119
56 16 1.1 18 400 9 250 1 870 940 12.4 13 000 9 500 16 000 63/22 ZZ VV DDU N NR 2.46 1.35 53.60 0.40 0.5 61.7 1.12 28.5 30.5 49.5 1 62.5 3.3 0.179
Notes (1) For tolerances for the snap ring grooves and snap ring dimensions, refer to Pages A50 to A53. Remarks 1. Diameter Series 7 (extra thin section bearings) are also available, please contact NSK.
(2) When heavy axial loads are applied, increase da and decrease Da from the above values. 2. When using bearings with rotating outer rings, contact NSK if they are sealed, shielded, or have snap rings.
(3) Ring types N and NR applicable only to open-type bearings. Please consult NSK about the snap ring groove
dimensions of sealed or shielded bearings.
B8 (4) Snap ring groove dimensions and snap ring dimensions are not conformed to ISO15. B9
B001-029E.indd 8-9 11/20/13 4:53:37 PM

Fa Fa
f f 0 Fa e >e
B e Fr Fr
C 0r
rN a b r0
X Y X Y
r ra
0.172 0.19 1 0 0.56 2.30
0.345 0.22 1 0 0.56 1.99
r ra ra 0.689 0.26 1 0 0.56 1.71
1.03 0.28 1 0 0.56 1.55
jD 2 1.38 0.30 1 0 0.56 1.45
jD jd jDa jda jD X 2.07 0.34 1 0 0.56 1.31
3.45 0.38 1 0 0.56 1.15
5.17 0.42 1 0 0.56 1.04
jD 1 6.89 0.44 1 0 0.56 1.00
Fa
>0.8, P0 =0.6Fr +0.5Fa
Fr
Fa
VV DD DDU N NR Fr
Bearing Numbers
25 37 7 0.3 4 500 3 150 455 320 16.1 18 000 10 000 22 000 6805 ZZ VV DD N NR 1.30 0.95 35.70 0.25 0.3 39.8 0.85 27 27 35 0.3 40.5 1.8 0.021
42 9 0.3 7 050 4 550 715 460 15.4 16 000 10 000 19 000 6905 ZZ VV DDU N( 3) NR( 3) 1.70 0.95 40.70 0.25 0.3 44.8 0.85 27 28.5 40 0.3 45.5 2.3 0.042
47 8 0.3 8 850 5 600 905 570 15.1 15 000 18 000 16005 27 45 0.3 0.059
47 12 0.6 10 100 5 850 1 030 595 14.5 15 000 9 500 18 000 6005 ZZ VV DDU N NR 2.06 1.35 44.60 0.40 0.5 52.7 1.12 29 30 43 0.6 53.5 2.9 0.079
52 15 1 14 000 7 850 1 430 800 13.9 13 000 9 000 15 000 6205 ZZ VV DDU N NR 2.46 1.35 49.73 0.40 0.5 57.9 1.12 30 32 47 1 58.5 3.3 0.129
62 17 1.1 20 600 11 200 2 100 1 150 13.2 11 000 8 000 13 000 6305 ZZ VV DDU N NR 3.28 1.90 59.61 0.60 0.5 67.7 1.70 31.5 36 55.5 1 68.5 4.6 0.235
28 52 12 0.6 12 500 7 400 1 270 755 14.5 14 000 8 500 16 000 60/28 ZZ VV DDU N NR 2.06 1.35 49.73 0.40 0.5 57.9 1.12 32 34 48 0.6 58.5 2.9 0.096
58 16 1 16 600 9 500 1 700 970 13.9 12 000 8 000 14 000 62/28 ZZ VV DDU N NR 2.46 1.35 55.60 0.40 0.5 63.7 1.12 33 35.5 53 1 64.5 3.3 0.175
68 18 1.1 26 700 14 000 2 730 1 430 12.4 10 000 7 500 13 000 63/28 ZZ VV DDU N NR 3.28 1.90 64.82 0.60 0.5 74.6 1.70 34.5 38 61.5 1 76 4.6 0.287
30 42 7 0.3 4 700 3 650 480 370 16.4 15 000 9 000 18 000 6806 ZZ VV DD N NR 1.30 0.95 40.70 0.25 0.3 44.8 0.85 32 32 40 0.3 45.5 1.8 0.024
47 9 0.3 7 250 5 000 740 510 15.8 14 000 8 500 17 000 6906 ZZ VV DDU N NR 1.70 0.95 45.70 0.25 0.3 49.8 0.85 32 34 45 0.3 50.5 2.3 0.052
55 9 0.3 11 200 7 350 1 150 750 15.2 13 000 15 000 16006 32 53 0.3 0.087
55 13 1 13 200 8 300 1 350 845 14.7 13 000 8 000 15 000 6006 ZZ VV DDU N NR 2.08 1.35 52.60 0.40 0.5 60.7 1.12 35 36.5 50 1 61.5 2.9 0.116
62 16 1 19 500 11 300 1 980 1 150 13.8 11 000 7 500 13 000 6206 ZZ VV DDU N NR 3.28 1.90 59.61 0.60 0.5 67.7 1.70 35 38.5 57 1 68.5 4.6 0.199
72 19 1.1 26 700 15 000 2 720 1 530 13.3 9 500 6 700 12 000 6306 ZZ VV DDU N NR 3.28 1.90 68.81 0.60 0.5 78.6 1.70 36.5 42.5 65.5 1 80 4.6 0.345
32 58 13 1 15 100 9 150 1 530 935 14.5 12 000 7 500 14 000 60/32 ZZ VV DDU N NR 2.08 1.35 55.60 0.40 0.5 63.7 1.12 37 38.5 53 1 64.5 2.9 0.122
65 17 1 20 700 11 600 2 120 1 190 13.6 10 000 7 100 12 000 62/32 ZZ VV DDU N NR 3.28 1.90 62.60 0.60 0.5 70.7 1.70 37 40 60 1 71.5 4.6 0.225
75 20 1.1 29 900 17 000 3 050 1 730 13.2 9 000 6 300 11 000 63/32 ZZ VV DDU N NR 3.28 1.90 71.83 0.60 0.5 81.6 1.70 38.5 44.5 68.5 1 83 4.6 0.389
35 47 7 0.3 4 900 4 100 500 420 16.7 14 000 7 500 16 000 6807 ZZ VV DD N NR 1.30 0.95 45.70 0.25 0.3 49.8 0.85 37 37 45 0.3 50.5 1.8 0.027
55 10 0.6 10 600 7 250 1 080 740 15.5 12 000 7 500 15 000 6907 ZZ VV DDU N NR 1.70 0.95 53.70 0.25 0.5 57.8 0.85 39 39 51 0.6 58.5 2.3 0.075
62 9 0.3 11 700 8 200 1 190 835 15.6 11 000 13 000 16007 37 60 0.3 0.107
62 14 1 16 000 10 300 1 630 1 050 14.8 11 000 6 700 13 000 6007 ZZ VV DDU N NR 2.08 1.90 59.61 0.60 0.5 67.7 1.70 40 41.5 57 1 68.5 3.4 0.151
72 17 1.1 25 700 15 300 2 620 1 560 13.8 9 500 6 300 11 000 6207 ZZ VV DDU N NR 3.28 1.90 68.81 0.60 0.5 78.6 1.70 41.5 44.5 65.5 1 80 4.6 0.284
80 21 1.5 33 500 19 200 3 400 1 960 13.2 8 500 6 000 10 000 6307 ZZ VV DDU N NR 3.28 1.90 76.81 0.60 0.5 86.6 1.70 43 47 72 1.5 88 4.6 0.464
40 52 7 0.3 6 350 5 550 650 565 17.0 12 000 6 700 14 000 6808 ZZ VV DD N NR 1.30 0.95 50.70 0.25 0.3 54.8 0.85 42 42 50 0.3 55.5 1.8 0.031
62 12 0.6 13 700 10 000 1 390 1 020 15.7 11 000 6 300 13 000 6908 ZZ VV DDU N NR 1.70 0.95 60.70 0.25 0.5 64.8 0.85 44 46 58 0.6 65.5 2.3 0.112
68 9 0.3 12 600 9 650 1 290 985 16.0 10 000 12 000 16008 42 66 0.3 0.13
68 15 1 16 800 11 500 1 710 1 180 15.3 10 000 6 000 12 000 6008 ZZ VV DDU N NR 2.49 1.90 64.82 0.60 0.5 74.6 1.70 45 47.5 63 1 76 3.8 0.19
80 18 1.1 29 100 17 900 2 970 1 820 14.0 8 500 5 600 10 000 6208 ZZ VV DDU N NR 3.28 1.90 76.81 0.60 0.5 86.6 1.70 46.5 50.5 73.5 1 88 4.6 0.366
90 23 1.5 40 500 24 000 4 150 2 450 13.2 7 500 5 300 9 000 6308 ZZ VV DDU N NR 3.28 2.70 86.79 0.60 0.5 96.5 2.46 48 53 82 1.5 98 5.4 0.636
45 58 7 0.3 6 600 6 150 670 625 17.2 11 000 6 000 13 000 6809 ZZ VV DD N NR 1.30 0.95 56.70 0.25 0.3 60.8 0.85 47 47.5 56 0.3 61.5 1.8 0.038
68 12 0.6 14 100 10 900 1 440 1 110 15.9 9 500 5 600 12 000 6909 ZZ VV DDU N NR 1.70 0.95 66.70 0.25 0.3( 4) 70.8 0.85 49 50 64 0.6 72 2.3 0.126
75 10 0.6 14 900 11 400 1 520 1 160 15.9 9 000 11 000 16009 49 71 0.6 0.167
75 16 1 20 900 15 200 2 140 1 550 15.3 9 000 5 300 11 000 6009 ZZ VV DDU N NR 2.49 1.90 71.83 0.60 0.5 81.6 1.70 50 53.5 70 1 83 3.8 0.241
85 19 1.1 31 500 20 400 3 200 2 080 14.4 7 500 5 300 9 000 6209 ZZ VV DDU N NR 3.28 1.90 81.81 0.60 0.5 91.6 1.70 51.5 55.5 78.5 1 93 4.6 0.42
100 25 1.5 53 000 32 000 5 400 3 250 13.1 6 700 4 800 8 000 6309 ZZ VV DDU N NR 3.28 2.70 96.80 0.60 0.5 106.50 2.46 53 61.5 92 1.5 108 5.4 0.829
(3) Ring types N and NR applicable only to open-type bearings. Please consult NSK about the snap ring groove
dimensions of sealed or shielded bearings.
B 10 (4) Not conformed to ISO15. B 11
B001-029E.indd 10-11 11/20/13 4:53:38 PM

Fa Fa
f f 0 Fa e >e
B e Fr Fr
C 0r
rN a b r0
X Y X Y
r ra
0.172 0.19 1 0 0.56 2.30
0.345 0.22 1 0 0.56 1.99
r ra ra 0.689 0.26 1 0 0.56 1.71
1.03 0.28 1 0 0.56 1.55
jD 2 1.38 0.30 1 0 0.56 1.45
jD jd jDa jda jD X 2.07 0.34 1 0 0.56 1.31
3.45 0.38 1 0 0.56 1.15
5.17 0.42 1 0 0.56 1.04
jD 1 6.89 0.44 1 0 0.56 1.00
Fa
>0.8, P0 =0.6Fr +0.5Fa
Fr
Fa
Fr
VV DD DDU N NR
Bearing Numbers
50 65 7 0.3 6 400 6 200 655 635 17.2 9 500 5 300 11 000 6810 ZZ VV DDU N NR 1.30 0.95 63.7 0.25 0.3 067.8 0.85 52 52.5 63 0.3 68.5 1.8 0.050
72 12 0.6 14 500 11 700 1 480 1 200 16.1 9 000 5 300 11 000 6910 ZZ VV DDU N NR 1.70 0.95 70.7 0.25 0.5 074.8 0.85 54 55 68 0.6 76 2.3 0.135
80 10 0.6 15 400 12 400 1 570 1 260 16.1 8 500 10 000 16010 54 76 0.6 0.175
80 16 1 21 800 16 600 2 220 1 700 15.6 8 500 4 800 10 000 6010 ZZ VV DDU N NR 2.49 1.90 076.81 0.60 0.5 086.6 1.70 55 58.5 75 1 88 3.8 0.261
90 20 1.1 35 000 23 200 3 600 2 370 14.4 7 100 4 800 8 500 6210 ZZ VV DDU N NR 3.28 2.70 086.79 0.60 0.5 096.5 2.46 56.5 60 83.5 1 98 5.4 0.459
110 27 2 62 000 38 500 6 300 3 900 13.2 6 000 4 300 7 500 6310 ZZ VV DDU N NR 3.28 2.70 106.81 0.60 0.5 116.6 2.46 59 68 101 2 118 5.4 1.06
55 72 9 0.3 8 800 8 500 900 865 17.0 8 500 4 800 10 000 6811 ZZ VV DDU N NR 1.70 0.95 70.7 0.25 0.3 074.8 0.85 57 59 70 0.3 76 2.3 0.081
80 13 1 16 000 13 300 1 630 1 350 16.2 8 000 4 500 9 500 6911 ZZ VV DDU N NR 2.10 1.30 77.9 0.40 0.5 084.4 1.12 60 61.5 75 1 86 2.9 0.189
90 11 0.6 19 400 16 300 1 980 1 660 16.2 7 500 9 000 16011 59 86 0.6 0.257
90 18 1.1 28 300 21 200 2 880 2 170 15.3 7 500 4 500 9 000 6011 ZZ VV DDU N NR 2.87 2.70 086.79 0.60 0.5 096.5 2.46 61.5 64 83.5 1 98 5.0 0.381
100 21 1.5 43 500 29 300 4 450 2 980 14.3 6 300 4 300 7 500 6211 ZZ VV DDU N NR 3.28 2.70 96.8 0.60 0.5 106.5 2.46 63 66.5 92 1.5 108 5.4 0.619
120 29 2 71 500 44 500 7 300 4 550 13.1 5 600 4 000 6 700 6311 ZZ VV DDU N NR 4.06 3.10 115.21 0.60 0.5 129.7 2.82 64 72.5 111 2 131.5 6.5 1.37
60 78 10 0.3 11 500 10 900 1 170 1 120 16.9 8 000 4 500 9 500 6812 ZZ VV DD N NR 1.70 1.30 76.2 0.40 0.3 082.7 1.12 62 64 76 0.3 84 2.5 0.103
85 13 1 19 400 16 300 1 980 1 660 16.2 7 500 4 300 9 000 6912 ZZ VV DDU N NR 2.10 1.30 82.9 0.40 0.5 089.4 1.12 65 66 80 1 91 2.9 0.192
95 11 0.6 20 000 17 500 2 040 1 780 16.3 7 100 8 500 16012 64 91 0.6 0.281
95 18 1.1 29 500 23 200 3 000 2 370 15.6 7 100 4 000 8 500 6012 ZZ VV DDU N NR 2.87 2.70 091.82 0.60 0.5 101.6 2.46 66.5 69 88.5 1 103 5.0 0.412
110 22 1.5 52 500 36 000 5 350 3 700 14.3 5 600 3 800 7 100 6212 ZZ VV DDU N NR 3.28 2.70 106.81 0.60 0.5 116.6 2.46 68 74.5 102 1.5 118 5.4 0.783
130 31 2.1 82 000 52 000 8 350 5 300 13.1 5 300 3 600 6 300 6312 ZZ VV DDU N NR 4.06 3.10 125.22 0.60 0.5 139.7 2.82 71 79 119 2 141.5 6.5 1.72
65 85 10 0.6 11 900 12 100 1 220 1 230 17.0 7 500 4 000 8 500 6813 ZZ VV DD N NR 1.70 1.30 82.9 0.40 0.5 089.4 1.12 69 69 81 0.6 91 2.5 0.128
90 13 1 17 400 16 100 1 770 1 640 16.6 7 100 4 000 8 500 6913 ZZ VV DDU N NR 2.10 1.30 87.9 0.40 0.5 094.4 1.12 70 71.5 85 1 96 2.9 0.218
100 11 0.6 20 500 18 700 2 090 1 910 16.5 6 700 8 000 16013 69 96 0.6 0.30
100 18 1.1 30 500 25 200 3 100 2 570 15.8 6 700 4 000 8 000 6013 ZZ VV DDU N NR 2.87 2.70 96.8 0.60 0.5 106.5 2.46 71.5 73 93.5 1 108 5.0 0.439
120 23 1.5 57 500 40 000 5 850 4 100 14.4 5 300 3 600 6 300 6213 ZZ VV DDU N NR 4.06 3.10 115.21 0.60 0.5 129.7 2.82 73 80 112 1.5 131.5 6.5 1.0
140 33 2.1 92 500 60 000 9 450 6 100 13.2 4 800 3 400 6 000 6313 ZZ VV DDU N NR 4.90 3.10 135.23 0.60 0.5 149.7 2.82 76 85.5 129 2 152 7.3 2.11
70 90 10 0.6 12 100 12 700 1 230 1 300 17.2 6 700 3 800 8 000 6814 ZZ VV DD N NR 1.70 1.30 87.9 0.40 0.5 094.4 1.12 74 74.5 86 0.6 96 2.5 0.134
100 16 1 23 700 21 200 2 420 2 160 16.3 6 300 3 600 7 500 6914 ZZ VV DDU N NR 2.50 1.30 97.9 0.40 0.5 104.4 1.12 75 77.5 95 1 106 3.3 0.349
110 13 0.6 26 800 23 600 2 730 2 410 16.3 6 000 7 100 16014 74 106 0.6 0.441
110 20 1.1 38 000 31 000 3 900 3 150 15.6 6 000 3 600 7 100 6014 ZZ VV DDU N NR 2.87 2.70 106.81 0.60 0.5 116.6 2.46 76.5 80.5 103.5 1 118 5.0 0.608
125 24 1.5 62 000 44 000 6 350 4 500 14.5 5 000 3 400 6 300 6214 ZZ VV DDU N NR 4.06 3.10 120.22 0.60 0.5 134.7 2.82 78 84 117 1.5 136.5 6.5 1.09
150 35 2.1 104 000 68 000 10 600 6 950 13.2 4 500 3 200 5 300 6314 ZZ VV DDU N NR 4.90 3.10 145.24 0.60 0.5 159.7 2.82 81 92 139 2 162 7.3 2.57
75 95 10 0.6 12 500 13 900 1 280 1 410 17.3 6 300 3 600 7 500 6815 ZZ VV DDU N NR 1.70 1.30 92.9 0.40 0.5 099.4 1.12 79 79.5 91 0.6 101 2.5 0.149
105 16 1 24 400 22 600 2 480 2 300 16.5 6 000 3 400 7 100 6915 ZZ VV DDU N NR 2.50 1.30 102.60 0.40 0.5 110.7 1.12 80 82 100 1 112 3.3 0.364
115 13 0.6 27 600 25 300 2 820 2 580 16.4 5 600 6 700 16015 79 111 0.6 0.463
115 20 1.1 39 500 33 500 4 050 3 400 15.8 5 600 3 400 6 700 6015 ZZ VV DDU N NR 2.87 2.70 111.81 0.60 0.5 121.6 2.46 81.5 85.5 108.5 1 123 5.0 0.649
130 25 1.5 66 000 49 500 6 750 5 050 14.7 4 800 3 200 5 600 6215 ZZ VV DDU N NR 4.06 3.10 125.22 0.60 0.5 139.7 2.82 83 90 122 1.5 141.5 6.5 1.19
160 37 2.1 113 000 77 000 11 600 7 850 13.2 4 300 2 800 5 000 6315 ZZ VV DDU N NR 4.90 3.10 155.22 0.60 0.5 169.7 2.82 86 98.5 149 2 172 7.3 3.08
3. Please consult NSK about the snap ring groove dimensions of sealed and shielded bearings when the diameter of
dimension series 18 and 19 is 50 mm or more.
B 12 B 13
B001-029E.indd 12-13 11/20/13 4:53:40 PM

Fa Fa
f f 0 Fa e >e
B e Fr Fr
C 0r
rN a b r0
X Y X Y
r ra
0.172 0.19 1 0 0.56 2.30
0.345 0.22 1 0 0.56 1.99
r ra ra 0.689 0.26 1 0 0.56 1.71
1.03 0.28 1 0 0.56 1.55
jD 2 1.38 0.30 1 0 0.56 1.45
jD jd jDa jda jD X 2.07 0.34 1 0 0.56 1.31
3.45 0.38 1 0 0.56 1.15
5.17 0.42 1 0 0.56 1.04
jD 1 6.89 0.44 1 0 0.56 1.00
Fa
>0.8, P0 =0.6Fr +0.5Fa
Fr
Fa
VV DD DDU N NR Fr
Bearing Numbers
80 100 10 0.6 12 700 14 500 1 290 1 470 17.4 6 000 3 400 7 100 6816 ZZ VV DDU N NR 1.70 1.3 97.9 0.4 0.5 104.4 1.12 84 84.5 96 0.6 106 2.5 0.151
110 16 1 25 000 24 000 2 540 2 450 16.6 5 600 3 200 6 700 6916 ZZ VV DDU N NR 2.50 1.3 107.60 0.4 0.5 115.7 1.12 85 87.5 105 1 117 3.3 0.391
125 14 0.6 32 000 29 600 3 250 3 000 16.4 5 300 6 300 16016 84 121 0.6 0.621
125 22 1.1 47 500 40 000 4 850 4 050 15.6 5 300 3 200 6 300 6016 ZZ VV DDU N NR 2.87 3.1 120.22 0.6 0.5 134.7 2.82 86.5 91 118.5 1 136.5 5.3 0.872
140 26 2 72 500 53 000 7 400 5 400 14.6 4 500 3 000 5 300 6216 ZZ VV DDU N NR 4.90 3.1 135.23 0.6 0.5 149.7 2.82 89 95.5 131 2 152 7.3 1.42
170 39 2.1 123 000 86 500 12 500 8 850 13.3 4 000 2 800 4 800 6316 ZZ VV DDU N NR 5.69 3.5 163.65 0.6 0.5 182.9 3.10 91 104.5 159 2 185 8.4 3.67
85 110 13 1 18 700 20 000 1 910 2 040 17.1 5 600 3 200 6 700 6817 ZZ VV DDU N NR 2.10 1.3 107.60 0.4 0.5 115.7 1.12 90 90.5 105 1 117 2.9 0.263
120 18 1.1 32 000 29 600 3 250 3 000 16.4 5 300 3 000 6 300 6917 ZZ VV DDU N NR 3.30 1.3 117.60 0.4 0.5 125.7 1.12 91.5 94.5 113.5 1 127 4.1 0.55
130 14 0.6 33 000 31 500 3 350 3 200 16.5 5 000 6 000 16017 89 126 0.6 0.652
130 22 1.1 49 500 43 000 5 050 4 400 15.8 5 000 3 000 6 000 6017 ZZ VV DDU N NR 2.87 3.1 125.22 0.6 0.5 139.7 2.82 91.5 96 123.5 1 141.5 5.3 0.918
150 28 2 84 000 62 000 8 550 6 300 14.5 4 300 2 800 5 000 6217 ZZ VV DDU N NR 4.90 3.1 145.24 0.6 0.5 159.7 2.82 94 102 141 2 162 7.3 1.76
180 41 3 133 000 97 000 13 500 9 850 13.3 3 800 2 600 4 500 6317 ZZ VV DDU N NR 5.69 3.5 173.66 0.6 0.5 192.9 3.10 98 110.5 167 2.5 195 8.4 4.28
90 115 13 1 19 000 21 000 1 940 2 140 17.2 5 300 3 000 6 300 6818 ZZ VV DDU N NR 2.10 1.3 112.60 0.4 0.5 120.7 1.12 95 95.5 110 1 122 2.9 0.276
125 18 1.1 33 000 31 500 3 350 3 200 16.5 5 000 2 800 6 000 6918 ZZ VV DDU N NR 3.30 1.3 122.60 0.4 0.5 130.7 1.12 96.5 98.5 118.5 1 132 4.1 0.585
140 16 1 41 500 39 500 4 250 4 000 16.3 4 800 5 600 16018 95 135 1 0.873
140 24 1.5 58 000 50 000 5 950 5 050 15.6 4 800 2 800 5 600 6018 ZZ VV DDU N NR 3.71 3.1 135.23 0.6 0.5 149.7 2.82 98 103 132 1.5 152 6.1 1.19
160 30 2 96 000 71 500 9 800 7 300 14.5 4 000 2 600 4 800 6218 ZZ VV DDU N NR 4.90 3.1 155.22 0.6 0.5 169.7 2.82 99 107.5 151 2 172 7.3 2.18
190 43 3 143 000 107 000 14 500 11 000 13.3 3 600 2 400 4 300 6318 ZZ VV DDU N NR 5.69 3.5 183.64 0.6 0.5 202.9 3.10 103 117 177 2.5 205 8.4 4.98
95 120 13 1 19 300 22 000 1 970 2 240 17.2 5 000 2 800 6 000 6819 ZZ VV DD N NR 2.10 1.3 117.60 0.4 0.5 125.7 1.12 100 101.5 115 1 127 2.9 0.297
130 18 1.1 33 500 33 500 3 450 3 400 16.6 4 800 2 800 5 600 6919 ZZ VV DDU N NR 3.30 1.3 127.60 0.4 0.5 135.7 1.12 101.5 103.5 123.5 1 137 4.1 0.601
145 16 1 43 000 42 000 4 350 4 250 16.4 4 500 5 300 16019 100 140 1 0.904
145 24 1.5 60 500 54 000 6 150 5 500 15.8 4 500 2 600 5 300 6019 ZZ VV DDU N NR 3.71 3.1 140.23 0.6 0.5 154.7 2.82 103 108.5 137 1.5 157 6.1 1.23
170 32 2.1 109 000 82 000 11 100 8 350 14.4 3 800 2 600 4 500 6219 ZZ VV DDU N NR 5.69 3.5 163.65 0.6 0.5 182.9 3.10 106 114 159 2 185 8.4 2.64
200 45 3 153 000 119 000 15 600 12 100 13.3 3 000 2 400 3 600 6319 ZZ VV DDU N NR 5.69 3.5 193.65 0.6 0.5 212.9 3.10 108 123.5 187 2.5 215 8.4 5.76
100 125 13 1 19 600 23 000 2 000 2 340 17.3 4 800 2 800 5 600 6820 ZZ VV DD N NR 2.10 1.3 122.60 0.4 0.5 130.7 1.12 105 105.5 120 1 132 2.9 0.31
140 20 1.1 43 000 42 000 4 350 4 250 16.4 4 500 2 600 5 300 6920 ZZ VV DDU N NR 3.30 1.9 137.60 0.6 0.5 145.7 1.70 106.5 111 133.5 1 147 4.7 0.828
150 16 1 42 500 42 000 4 300 4 300 16.5 4 300 5 300 16020 105 145 1 0.945
150 24 1.5 60 000 54 000 6 150 5 550 15.9 4 300 2 600 5 300 6020 ZZ VV DDU N NR 3.71 3.1 145.24 0.6 0.5 159.7 2.82 108 112.5 142 1.5 162 6.1 1.29
180 34 2.1 122 000 93 000 12 500 9 500 14.4 3 600 2 400 4 300 6220 ZZ VV DDU N NR 5.69 3.5 173.66 0.6 0.5 192.9 3.10 111 121.5 169 2 195 8.4 3.17
215 47 3 173 000 141 000 17 700 14 400 13.2 2 800 2 200 3 400 6320 ZZ VV DDU 113 133 202 2.5 7.04
105 130 13 1 19 800 23 900 2 020 2 440 17.4 4 800 2 600 5 600 6821 ZZ VV DDU N NR 2.10 1.3 127.60 0.4 0.5 135.7 1.12 110 110.5 125 1 137 2.9 0.324
145 20 1.1 42 500 42 000 4 300 4 300 16.5 4 300 5 300 6921 ZZ VV N NR 3.30 1.9 142.60 0.6 0.5 150.7 1.70 111.5 116 138.5 1 152 4.7 0.856
160 18 1 52 000 50 500 5 300 5 150 16.3 4 000 4 800 16021 110 155 1 1.24
160 26 2 72 500 66 000 7 400 6 700 15.8 4 000 2 400 4 800 6021 ZZ VV DDU N NR 3.71 3.1 155.22 0.6 0.5 169.7 2.82 114 120 151 2 172 6.1 1.58
190 36 2.1 133 000 105 000 13 600 10 700 14.4 3 400 2 200 4 000 6221 ZZ VV DDU N NR 5.69 3.5 183.64 0.6 0.5 202.9 3.10 116 127.5 179 2 205 8.4 3.79
225 49 3 184 000 154 000 18 700 15 700 13.2 2 600 2 000 3 200 6321 ZZ DDU 118 138 212 2.5 8.09
3. Please consult NSK about the snap ring groove dimensions of sealed and shielded bearings when the diameter of
B 14 B 15
B001-029E.indd 14-15 11/20/13 4:53:41 PM

Fa Fa
f f 0 Fa e >e
B e Fr Fr
C 0r
rN a b r0
X Y X Y
r ra
0.172 0.19 1 0 0.56 2.30
0.345 0.22 1 0 0.56 1.99
r ra ra 0.689 0.26 1 0 0.56 1.71
1.03 0.28 1 0 0.56 1.55
jD 2 1.38 0.30 1 0 0.56 1.45
jD jd jDa jda jD X 2.07 0.34 1 0 0.56 1.31
3.45 0.38 1 0 0.56 1.15
5.17 0.42 1 0 0.56 1.04
jD 1 6.89 0.44 1 0 0.56 1.00
Fa
>0.8, P0 =0.6Fr +0.5Fa
Fr
Fa
ZZ ZZS Sealed Type Sealed Type Ring Groove Snap Ring 0.8, P0 =Fr
VV DD DDU N NR Fr
Bearing Numbers
110 140 16 1 28 100 32 500 2 860 3 350 17.1 4 300 2 400 5 300 6822 ZZ VV DDU N NR 2.50 1.9 137.60 0.6 0.5 145.7 1.7 115 117 135 1 147 3.9 0.497
150 20 1.1 43 500 44 500 4 450 4 550 16.6 4 300 2 400 5 000 6922 ZZ VV DDU N NR 3.30 1.9 147.60 0.6 0.5 155.7 1.7 116.5 121 143.5 1 157 4.7 0.893
170 19 1 57 500 56 500 5 850 5 800 16.3 3 800 4 500 16022 115 165 1 1.51
170 28 2 85 000 73 000 8 650 7 450 15.5 3 800 2 200 4 500 6022 ZZ VV DDU N NR 3.71 3.5 163.65 0.6 0.5 182.9 3.1 119 124.5 161 2 185 6.4 1.94
200 38 2.1 144 000 117 000 14 700 11 900 14.3 2 800 2 200 3 400 6222 ZZ VV DDU N NR 5.69 3.5 193.65 0.6 0.5 212.9 3.1 121 134 189 2 215 8.4 4.45
240 50 3 205 000 179 000 20 900 18 300 13.2 2 400 3 000 6322 ZZ 123 147 227 2.5 9.51
120 150 16 1 28 900 35 500 2 950 3 650 17.3 4 000 2 200 4 800 6824 ZZ VV DD N NR 2.50 1.9 147.60 0.6 0.5 155.7 1.7 125 127 145 1 157 3.9 0.537
165 22 1.1 53 000 54 000 5 400 5 500 16.5 3 800 4 500 6924 ZZ N NR 3.70 1.9 161.80 0.6 0.5 171.5 1.7 126.5 132 158.5 1 173 5.1 1.21
180 19 1 56 500 57 500 5 800 5 850 16.5 3 600 4 300 16024 125 175 1 1.6
180 28 2 88 000 80 000 9 000 8 150 15.7 3 600 2 200 4 300 6024 ZZ VV DDU N NR 3.71 3.5 173.66 0.6 0.5 192.9 3.1 129 134.5 171 2 195 6.4 2.08
215 40 2.1 155 000 131 000 15 800 13 400 14.4 2 600 2 000 3 200 6224 ZZ VV DDU 131 146 204 2 5.29
260 55 3 207 000 185 000 21 100 18 800 13.5 2 200 1 800 2 800 6324 ZZS DDU 133 161 247 2.5 12.5
130 165 18 1.1 37 000 44 000 3 750 4 450 17.1 3 600 2 000 4 300 6826 ZZS VV DD N NR 3.30 1.9 161.80 0.6 0.5 171.5 1.7 136.5 138 158.5 1 173 4.7 0.758
180 24 1.5 65 000 67 500 6 650 6 850 16.5 3 400 4 000 6926 ZZ N NR 3.70 1.9 176.80 0.6 0.5 186.5 1.7 138 144 172 1.5 188 5.1 1.57
200 22 1.1 75 500 77 500 7 700 7 900 16.4 3 000 3 600 16026 136.5 193.5 1 2.4
200 33 2 106 000 101 000 10 800 10 300 15.8 3 000 1 900 3 600 6026 ZZ DDU N NR 5.69 3.5 193.65 0.6 0.5 212.9 3.1 139 148.5 191 2 215 8.4 3.26
230 40 3 167 000 146 000 17 000 14 900 14.5 2 400 3 000 6226 ZZ 143 157 217 2.5 5.96
280 58 4 229 000 214 000 23 400 21 800 13.6 2 200 2 600 6326 ZZS 146 175 264 3 15.2
140 175 18 1.1 38 500 48 000 3 900 4 850 17.3 3 400 1 900 4 000 6828 ZZ VV DDU N NR 3.30 1.9 171.80 0.6 0.5 181.5 1.7 146.5 148.5 168.5 1 183 4.7 0.832
190 24 1.5 66 500 72 000 6 800 7 300 16.6 3 200 3 800 6928 ZZS VV N NR 3.70 1.9 186.80 0.6 0.5 196.5 1.7 148 153.5 182 1.5 198 5.1 1.67
210 22 1.1 77 500 82 500 7 900 8 400 16.5 2 800 3 400 16028 146.5 203.5 1 2.84
210 33 2 110 000 109 000 11 200 11 100 16.0 2 800 1 800 3 400 6028 ZZ DDU 149 158.5 201 2 3.48
250 42 3 166 000 150 000 17 000 15 300 14.9 2 200 1 700 2 800 6228 ZZS DDU 153 171.5 237 2.5 7.68
300 62 4 253 000 246 000 25 800 25 100 13.6 2 000 2 400 6328 ZZS 156 187 284 3 18.5
150 190 20 1.1 47 500 58 500 4 850 5 950 17.1 3 200 1 800 3 800 6830 ZZ VV DDU N NR 3.30 1.9 186.80 0.6 0.5 196.5 1.7 156.5 160 183.5 1 198 4.7 1.15
210 28 2 85 000 90 500 8 650 9 200 16.5 2 600 1 700 3 200 6930 ZZS DDU 159 166 201 2 3.01
225 24 1.1 84 000 91 000 8 550 9 250 16.6 2 600 3 000 16030 156.5 218.5 1 3.62
225 35 2.1 126 000 126 000 12 800 12 800 15.9 2 600 1 700 3 000 6030 ZZ VV DDU 161 170 214 2 4.24
270 45 3 176 000 168 000 18 000 17 100 15.1 2 000 2 600 6230 ZZS 163 186 257 2.5 10
320 65 4 274 000 284 000 28 000 28 900 13.9 1 800 2 200 6330 ZZS 166 203 304 3 22.7
160 200 20 1.1 48 500 61 000 4 950 6 250 17.2 2 600 1 700 3 200 6832 ZZS VV DDU N NR 3.30 1.9 196.80 0.6 0.5 206.5 1.7 166.5 170.5 193.5 1 208 4.7 1.23
220 28 2 87 000 96 000 8 850 9 800 16.6 2 600 1 600 3 000 6932 ZZS DDU 169 176 211 2 2.71
240 25 1.5 99 000 108 000 10 100 11 000 16.5 2 400 2 800 16032 168 232 1.5 4.2
240 38 2.1 137 000 135 000 13 900 13 800 15.9 2 400 1 600 2 800 6032 ZZ DDU 171 181.5 229 2 5.15
290 48 3 185 000 186 000 18 900 19 000 15.4 1 900 2 400 6232 ZZS 173 202 277 2.5 12.8
340 68 4 278 000 287 000 28 300 29 200 13.9 1 700 2 000 6332 ZZS 176 215.5 324 3 26.2
Notes (1) For tolerances for the snap ring grooves and snap ring dimensions, refer to Pages A50 to A53. Remarks 1. When using bearings with rotating outer rings, contact NSK if they are sealed, shielded, or have snap rings.
(2) When heavy axial loads are applied, increase da and decrease Da from the above values. 2. Please consult NSK about the snap ring groove dimensions of sealed and shielded bearings when the diameter of
B 16 B 17
B001-029E.indd 16-17 11/20/13 4:53:43 PM

B Fa Fa
f 0Fa e >e
ra e Fr Fr
r C 0r
X Y X Y
0.172 0.19 1 0 0.56 2.30
r ra 0.345 0.22 1 0 0.56 1.99
0.689 0.26 1 0 0.56 1.71
jD jd jDa jda 1.03 0.28 1 0 0.56 1.55
1.38 0.30 1 0 0.56 1.45
2.07 0.34 1 0 0.56 1.31
3.45 0.38 1 0 0.56 1.15
5.17 0.42 1 0 0.56 1.04
6.89 0.44 1 0 0.56 1.00
Fa
>0.8, P0 =0.6Fr +0.5Fa
Fr
Shielded Type Non-Contact Fa
Open Type
ZZS Sealed Type 0.8, P0 =Fr
Fr
VV
Boundary Dimensions Basic Load Ratings Factor Limiting Speeds (min 1) Abutment and Fillet Mass
Bearing Numbers
(mm) (N) {kgf} Dimensions (mm) (kg)
Grease Oil
Z ZZ DU Open Open Shielded Sealed d a(1) D a(1) ra
min. V VV DDU Z min. max. max. max. approx.
170 215 22 1.1 60 000 75 000 6 100 7 650 17.1 2 600 1 600 3 000 6834 ZZS VV DDU 176.5 182.0 208.5 1 1.86
230 28 2 86 000 97 000 8 750 9 850 16.7 2 400 2 800 6934 ZZS 179 186.0 221 2 3.34
260 28 1.5 114 000 126 000 11 700 12 900 16.5 2 200 2 600 16034 178 252 1.5 5.71
260 42 2.1 161 000 161 000 16 400 16 400 15.8 2 200 2 600 6034 ZZS VV 181 194.5 249 2 6.89
310 52 4 212 000 224 000 21 700 22 800 15.3 1 800 2 200 6234 ZZS 186 215.0 294 3 15.8
360 72 4 325 000 355 000 33 500 36 000 13.6 1 600 2 000 6334 186 344 3 36.6
180 225 22 1.1 60 500 78 500 6 200 8 000 17.2 2 400 2 800 6836 VV 186.5 192.0 218.5 1 1.98
250 33 2 119 000 128 000 12 100 13 100 16.4 2 200 2 600 6936 ZZS 189 198.5 241 2 4.16
280 31 2 145 000 157 000 14 700 16 000 16.3 2 000 2 400 16036 189 271 2 7.5
280 46 2.1 180 000 185 000 18 400 18 800 15.6 2 000 2 400 6036 ZZS VV 191 208.0 269 2 8.88
320 52 4 227 000 241 000 23 200 24 600 15.1 1 700 2 000 6236 ZZS 196 223.0 304 3 15.9
380 75 4 355 000 405 000 36 000 41 500 13.9 1 500 1 800 6336 196 364 3 43.1
190 240 24 1.5 73 000 93 500 7 450 9 550 17.1 2 200 2 600 6838 VV 198 202.5 232 1.5 2.53
260 33 2 113 000 127 000 11 500 13 000 16.6 2 200 2 600 6938 199 251 2 5.18
290 31 2 149 000 168 000 15 200 17 100 16.4 2 000 2 400 16038 199 281 2 7.78
290 46 2.1 188 000 201 000 19 200 20 500 15.8 2 000 2 400 6038 ZZS 201 218.0 279 2 9.39
340 55 4 255 000 282 000 26 000 28 700 15.0 1 600 2 000 6238 ZZS 206 236.0 324 3 22.3
400 78 5 355 000 415 000 36 000 42 500 14.1 1 400 1 700 6338 210 380 4 49.7
200 250 24 1.5 74 000 98 000 7 550 10 000 17.2 2 200 2 600 6840 208 242 1.5 2.67
280 38 2.1 143 000 158 000 14 600 16 100 16.4 2 000 2 400 6940 ZZS 211 222.0 269 2 7.28
310 34 2 161 000 180 000 16 400 18 300 16.4 1 900 2 200 16040 209 301 2 10
310 51 2.1 207 000 226 000 21 100 23 000 15.6 1 900 2 200 6040 ZZS 211 231.5 299 2 12
360 58 4 269 000 310 000 27 400 31 500 15.2 1 500 1 800 6240 ZZS 216 252.0 344 3 26.7
420 80 5 380 000 445 000 38 500 45 500 13.8 1 300 1 600 6340 220 400 4 55.3
220 270 24 1.5 76 500 107 000 7 800 10 900 17.4 1 900 2 400 6844 ZZS 228 233.5 262 1.5 2.9
300 38 2.1 146 000 169 000 14 900 17 300 16.6 1 800 2 200 6944 ZZS 231 242.0 289 2 7.88
340 37 2.1 180 000 217 000 18 400 22 100 16.5 1 600 2 000 16044 231 329 2 13.1
340 56 3 235 000 271 000 24 000 27 600 15.6 1 700 2 000 6044 ZZS 233 254.5 327 2.5 18.6
400 65 4 310 000 375 000 31 500 38 500 15.1 1 300 1 600 6244 236 384 3 37.4
460 88 5 410 000 520 000 42 000 53 000 14.3 1 200 1 500 6344 240 440 4 73.9
240 300 28 2 98 500 137 000 10 000 14 000 17.3 1 700 2 000 6848 249 291 2 4.48
320 38 2.1 154 000 190 000 15 700 19 400 16.8 1 700 2 000 6948 ZZS 251 262.0 309 2 8.49
360 37 2.1 196 000 243 000 19 900 24 700 16.5 1 500 1 900 16048 251 349 2 13.9
360 56 3 244 000 296 000 24 900 30 000 15.9 1 500 1 900 6048 253 347 2.5 19.9
440 72 4 340 000 430 000 34 500 44 000 15.2 1 200 1 500 6248 256 424 3 50.5
500 95 5 470 000 625 000 48 000 63 500 14.2 1 100 1 300 6348 260 480 4 94.4
Note (1) When heavy axial loads are applied, increase da and decrease Da from the above values.
Remarks When using bearings with rotating outer rings, contact NSK if they are sealed or shielded.
B 18 B 19
B001-029E.indd 18-19 11/20/13 4:53:44 PM

Fa Fa
B
f 0Fa e >e
e Fr Fr
C 0r
r ra X Y X Y
0.172 0.19 1 0 0.56 2.30
0.345 0.22 1 0 0.56 1.99
r ra 0.689 0.26 1 0 0.56 1.71
1.03 0.28 1 0 0.56 1.55
jD jd jDa 1.38 0.30 1 0 0.56 1.45
jd a 2.07 0.34 1 0 0.56 1.31
3.45 0.38 1 0 0.56 1.15
5.17 0.42 1 0 0.56 1.04
6.89 0.44 1 0 0.56 1.00
Fa
>0.8, P0 =0.6Fr +0.5Fa
Fr
Open Type Fa
0.8, P0 =Fr
Fr
Boundary Dimensions Basic Load Ratings Factor Limiting Speeds Bearing Abutment and Fillet Mass
(mm) (N) {kgf} (min 1) Numbers Dimensions (mm) (kg)
d D B r Cr C 0r Cr C 0r f0 Grease Oil Open da(1) Da(1) ra

min. min. max. max. approx.
260 320 28 2 101 000 148 000 10 300 15 100 17.4 1 600 1 900 6852 269 311 2 4.84
360 46 2.1 204 000 255 000 20 800 26 000 16.5 1 500 1 800 6952 271 349 2 14
400 44 3 237 000 310 000 24 100 31 500 16.4 1 400 1 700 16052 273 387 2.5 21.1
400 65 4 291 000 375 000 29 700 38 500 15.8 1 400 1 700 6052 276 384 3 29.4
480 80 5 400 000 540 000 41 000 55 000 15.1 1 100 1 300 6252 280 460 4 67
540 102 6 505 000 710 000 51 500 72 500 14.6 1 000 1 200 6352 286 514 5 118
280 350 33 2 133 000 191 000 13 600 19 500 17.3 1 500 1 700 6856 289 341 2 7.2
380 46 2.1 209 000 272 000 21 300 27 700 16.6 1 400 1 700 6956 291 369 2 15.1
420 44 3 243 000 330 000 24 700 33 500 16.5 1 300 1 600 16056 293 407 2.5 22.7
420 65 4 300 000 410 000 31 000 41 500 16.0 1 300 1 600 6056 296 404 3 31.2
500 80 5 400 000 550 000 41 000 56 000 15.2 1 000 1 300 6256 300 480 4 70.4
580 108 6 570 000 840 000 58 000 86 000 14.5 900 1 100 6356 306 554 5 144
300 380 38 2.1 166 000 233 000 17 000 23 800 17.1 1 300 1 600 6860 311 369 2 10.3
420 56 3 269 000 370 000 27 400 38 000 16.4 1 300 1 500 6960 313 407 2.5 23.9
460 50 4 285 000 405 000 29 000 41 000 16.4 1 200 1 400 16060 316 444 3 31.5
460 74 4 355 000 500 000 36 500 51 000 15.8 1 200 1 400 6060 316 444 3 44.2
540 85 5 465 000 670 000 47 500 68 500 15.1 950 1 200 6260 320 520 4 87.8
320 400 38 2.1 168 000 244 000 17 200 24 900 17.2 1 300 1 500 6864 331 389 2 10.8
440 56 3 266 000 375 000 27 100 38 000 16.5 1 200 1 400 6964 333 427 2.5 25.3
480 50 4 293 000 430 000 29 800 44 000 16.5 1 100 1 300 16064 336 464 3 33.2
480 74 4 390 000 570 000 40 000 58 000 15.7 1 100 1 300 6064 336 464 3 46.5
580 92 5 530 000 805 000 54 500 82 500 15.0 850 1 100 6264 340 560 4 111
340 420 38 2.1 175 000 265 000 17 800 27 100 17.3 1 200 1 400 6868 351 409 2 11.5
460 56 3 273 000 400 000 27 800 40 500 16.6 1 100 1 300 6968 353 447 2.5 26.6
520 82 5 440 000 660 000 45 000 67 500 15.6 1 000 1 200 6068 360 500 4 62.3
620 92 6 530 000 820 000 54 000 83 500 15.3 800 1 000 6268 366 594 5 129
360 440 38 2.1 192 000 290 000 19 600 29 600 17.3 1 100 1 300 6872 371 429 2 11.8
480 56 3 280 000 425 000 28 500 43 000 16.7 1 100 1 300 6972 373 467 2.5 27.9
540 82 5 460 000 720 000 47 000 73 500 15.7 950 1 200 6072 380 520 4 65.3
650 95 6 555 000 905 000 57 000 92 000 15.4 750 950 6272 386 624 5 145
B 20 B 21
B001-029E.indd 20-21 11/20/13 4:53:45 PM

Fa Fa
B
f 0Fa e >e
e Fr Fr
C 0r
r ra X Y X Y
0.172 0.19 1 0 0.56 2.30
0.345 0.22 1 0 0.56 1.99
r ra 0.689 0.26 1 0 0.56 1.71
1.03 0.28 1 0 0.56 1.55
jD jd jDa 1.38 0.30 1 0 0.56 1.45
jd a 2.07 0.34 1 0 0.56 1.31
3.45 0.38 1 0 0.56 1.15
5.17 0.42 1 0 0.56 1.04
6.89 0.44 1 0 0.56 1.00
Fa
>0.8, P0 =0.6Fr +0.5Fa
Fr
Open Type Fa
0.8, P0 =Fr
Fr

380 480 46 2.1 238 000 375 000 24 200 38 000 17.1 1 000 1 200 6876 391 469 2 19.5
520 65 4 325 000 510 000 33 000 52 000 16.6 950 1 200 6976 396 504 3 40
560 82 5 455 000 725 000 46 500 74 000 15.9 900 1 100 6076 400 540 4 68
400 500 46 2.1 241 000 390 000 24 600 40 000 17.2 950 1 200 6880 411 489 2 20.5
540 65 4 335 000 540 000 34 000 55 000 16.7 900 1 100 6980 416 524 3 42
600 90 5 510 000 825 000 52 000 84 000 15.7 850 1 000 6080 420 580 4 88.4
420 520 46 2.1 245 000 410 000 25 000 41 500 17.3 900 1 100 6884 431 509 2 21.4
560 65 4 340 000 570 000 35 000 58 500 16.8 900 1 100 6984 436 544 3 43.6
620 90 5 530 000 895 000 54 000 91 000 15.8 800 1 000 6084 440 600 4 92.2
440 540 46 2.1 248 000 425 000 25 300 43 500 17.4 900 1 100 6888 451 529 2 22.3
600 74 4 395 000 680 000 40 500 69 000 16.6 800 1 000 6988 456 584 3 60.2
650 94 6 550 000 965 000 56 000 98 500 16.0 750 900 6088 466 624 5 106
460 580 56 3 310 000 550 000 31 500 56 000 17.1 800 1 000 6892 473 567 2.5 34.3
620 74 4 405 000 720 000 41 500 73 500 16.7 800 950 6992 476 604 3 62.6
680 100 6 605 000 1 080 000 62 000 110 000 15.8 710 850 6092 486 654 5 123
480 600 56 3 315 000 575 000 32 000 58 500 17.2 800 950 6896 493 587 2.5 35.4
650 78 5 450 000 815 000 45 500 83 000 16.6 750 900 6996 500 630 4 73.5
700 100 6 605 000 1 090 000 61 500 111 000 15.9 710 850 6096 506 674 5 127
500 620 56 3 320 000 600 000 33 000 61 000 17.3 750 900 68/500 513 607 2.5 37.2
670 78 5 460 000 865 000 47 000 88 000 16.7 710 850 69/500 520 650 4 82
720 100 6 630 000 1 170 000 64 000 120 000 16.0 670 800 60/500 526 694 5 131
530 650 56 3 325 000 625 000 33 000 63 500 17.4 710 850 68/530 543 637 2.5 39.8
710 82 5 455 000 870 000 46 500 88 500 16.8 670 800 69/530 550 690 4 89.8
780 112 6 680 000 1 300 000 69 500 133 000 16.0 600 750 60/530 556 754 5 184
560 680 56 3 330 000 650 000 33 500 66 500 17.4 670 800 68/560 573 667 2.5 41.5
750 85 5 525 000 1 040 000 53 500 106 000 16.7 600 750 69/560 580 730 4 105
820 115 6 735 000 1 500 000 75 000 153 000 16.2 560 670 60/560 586 793.5 5 203
600 730 60 3 355 000 735 000 36 000 75 000 17.5 600 710 68/600 613 717 2.5 50.9
800 90 5 550 000 1 160 000 56 500 118 000 16.9 560 670 69/600 620 780 4 120
870 118 6 790 000 1 640 000 80 500 168 000 16.1 530 630 60/600 626 844 5 236
B 22 B 23
B001-029E.indd 22-23 11/20/13 4:53:46 PM

Fa Fa
B
f 0Fa e >e
e Fr Fr
C 0r
r ra X Y X Y
0.172 0.19 1 0 0.56 2.30
0.345 0.22 1 0 0.56 1.99
r ra 0.689 0.26 1 0 0.56 1.71
1.03 0.28 1 0 0.56 1.55
jD jd jDa 1.38 0.30 1 0 0.56 1.45
jd a 2.07 0.34 1 0 0.56 1.31
3.45 0.38 1 0 0.56 1.15
5.17 0.42 1 0 0.56 1.04
6.89 0.44 1 0 0.56 1.00
Fa
>0.8, P0 =0.6Fr +0.5Fa
Fr
Open Type Fa
0.8, P0 =Fr
Fr

630 780 69 4 420 000 890 000 43 000 90 500 17.3 560 670 68/630 646 764 3 71.3
850 100 6 625 000 1 350 000 64 000 138 000 16.7 530 630 69/630 656 824 5 163
920 128 7.5 750 000 1 620 000 76 500 165 000 16.4 480 600 60/630 662 888 6 285
670 820 69 4 435 000 965 000 44 500 98 000 17.4 500 630 68/670 686 804 3 75.4
900 103 6 675 000 1 460 000 68 500 149 000 16.7 480 560 69/670 696 874 5 181
980 136 7.5 765 000 1 730 000 78 000 177 000 16.6 450 530 60/670 702 948 6 351
710 870 74 4 480 000 1 100 000 49 000 113 000 17.4 480 560 68/710 726 854 3 92.6
950 106 6 715 000 1 640 000 72 500 167 000 16.8 450 530 69/710 736 924 5 208
750 920 78 5 525 000 1 260 000 53 500 128 000 17.4 430 530 68/750 770 900 4 110
1 000 112 6 785 000 1 840 000 80 000 188 000 16.7 400 500 69/750 776 974 5 245
800 980 82 5 530 000 1 310 000 54 000 133 000 17.5 400 480 68/800 820 960 4 132
1 060 115 6 825 000 2 050 000 84 500 209 000 16.8 380 450 69/800 826 1 034 5 275
B 24 B 25
B001-029E.indd 24-25 11/20/13 4:53:47 PM

MAXIMUM TYPE BALL BEARINGS
Bore Diameter 25 110 mm
B
r ra ra
r ra ra
jD jd jD a jd a jD a jd b
Shielded Type Shielded Type

Open Type
(One Shield) Z (Two Shields) ZZ
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers Abutment and Fillet Dimensions Mass
(mm) (N) {kgf} (min 1) (mm) (kg)
Grease Oil
d D B r Cr C 0r Cr C 0r Open Open
Open With With da db Da ra
min. One Shielded Two Shields min. max. max. max. approx.
Z ZZ Z
25 52 15 1 14 400 10 500 1 470 1 070 12 000 15 000 BL 205 BL 205 Z BL 205 ZZ 30 32 47 1 0.133
62 17 1.1 21 500 15 500 2 200 1 580 11 000 13 000 BL 305 BL 305 Z BL 305 ZZ 31.5 36 55.5 1 0.246
30 62 16 1 21 000 16 300 2 150 1 660 10 000 12 000 BL 206 BL 206 Z BL 206 ZZ 35 38.5 57 1 0.215
72 19 1.1 27 900 20 700 2 840 2 110 9 000 11 000 BL 306 BL 306 Z BL 306 ZZ 36.5 42 65.5 1 0.364
35 72 17 1.1 27 800 22 100 2 830 2 250 9 000 11 000 BL 207 BL 207 Z BL 207 ZZ 41.5 44.5 65.5 1 0.307
80 21 1.5 37 000 29 100 3 800 2 970 8 000 9 500 BL 307 BL 307 Z BL 307 ZZ 43 44.5 72 1.5 0.486
40 80 18 1.1 35 500 28 800 3 600 2 940 8 000 9 500 BL 208 BL 208 Z BL 208 ZZ 46.5 50 73.5 1 0.394
90 23 1.5 46 500 36 000 4 750 3 650 7 500 9 000 BL 308 BL 308 Z BL 308 ZZ 48 52.5 82 1.5 0.685
45 85 19 1.1 37 000 32 000 3 800 3 250 7 500 9 000 BL 209 BL 209 Z BL 209 ZZ 51.5 55.5 78.5 1 0.449
100 25 1.5 55 500 44 000 5 650 4 500 6 300 8 000 BL 309 BL 309 Z BL 309 ZZ 53 61.5 92 1.5 0.883
50 90 20 1.1 39 000 35 000 3 950 3 550 6 700 8 500 BL 210 BL 210 Z BL 210 ZZ 56.5 60 83.5 1 0.504
110 27 2 65 000 52 500 6 600 5 350 6 000 7 100 BL 310 BL 310 Z BL 310 ZZ 59 68 101 2 1.16
55 100 21 1.5 48 000 44 000 4 900 4 500 6 300 7 500 BL 211 BL 211 Z BL 211 ZZ 63 66.5 92 1.5 0.667
120 29 2 75 000 61 500 7 650 6 250 5 600 6 700 BL 311 BL 311 Z BL 311 ZZ 64 72.5 111 2 1.49
60 110 22 1.5 58 000 54 000 5 950 5 550 5 600 6 700 BL 212 BL 212 Z BL 212 ZZ 68 74.5 102 1.5 0.856
130 31 2.1 85 500 71 500 8 700 7 300 5 000 6 000 BL 312 BL 312 Z BL 312 ZZ 71 79 119 2 1.88
65 120 23 1.5 63 500 60 000 6 450 6 150 5 300 6 300 BL 213 BL 213 Z BL 213 ZZ 73 80 112 1.5 1.09
140 33 2.1 103 000 89 500 10 500 9 150 4 800 5 600 BL 313 BL 313 Z BL 313 ZZ 76 85.5 129 2 2.36
70 125 24 1.5 69 000 66 000 7 050 6 750 5 000 6 000 BL 214 BL 214 Z BL 214 ZZ 78 84 117 1.5 1.19
150 35 2.1 115 000 102 000 11 800 10 400 4 300 5 300 BL 314 BL 314 Z BL 314 ZZ 81 92 139 2 2.87
75 130 25 1.5 72 000 72 000 7 350 7 300 4 500 5 600 BL 215 BL 215 Z BL 215 ZZ 83 90 122 1.5 1.29
160 37 2.1 126 000 116 000 12 800 11 800 4 000 5 000 BL 315 BL 315 Z BL 315 ZZ 86 98.5 149 2 3.43
80 140 26 2 84 000 85 000 8 600 8 650 4 300 5 300 BL 216 BL 216 Z BL 216 ZZ 89 95.5 131 2 1.61
170 39 2.1 136 000 130 000 13 900 13 300 3 800 4 500 BL 316 BL 316 Z BL 316 ZZ 91 104.5 159 2 4.08
85 150 28 2 93 000 93 000 9 500 9 450 4 000 5 000 BL 217 BL 217 Z BL 217 ZZ 94 102 141 2 1.97
180 41 3 147 000 145 000 15 000 14 800 3 600 4 300 BL 317 BL 317 Z BL 317 ZZ 98 110.5 167 2.5 4.77
90 160 30 2 107 000 107 000 10 900 10 900 3 800 4 500 BL 218 BL 218 Z BL 218 ZZ 99 107.5 151 2 2.43
190 43 3 158 000 161 000 16 100 16 400 3 400 4 000 BL 318 BL 318 Z BL 318 ZZ 103 117 177 2.5 5.45
95 170 32 2.1 121 000 123 000 12 300 12 500 3 600 4 300 BL 219 BL 219 Z BL 219 ZZ 106 114 159 2 2.95
200 45 3 169 000 178 000 17 300 18 100 2 800 3 600 BL 319 BL 319 Z BL 319 ZZ 108 124 187 2.5 6.4
100 180 34 2.1 136 000 140 000 13 800 14 200 3 400 4 000 BL 220 BL 220 Z BL 220 ZZ 111 121.5 169 2 3.54
105 190 36 2.1 148 000 157 000 15 000 16 000 3 200 3 800 BL 221 BL 221 Z BL 221 ZZ 116 127.5 179 2 4.23
110 200 38 2.1 160 000 176 000 16 300 17 900 2 800 3 400 BL 222 121 189 2 4.84
Remarks When using Maximum Type Ball Bearings, please contact NSK.
B 26 B 27
B001-029E.indd 26-27 11/20/13 4:53:47 PM

MAGNETO BEARINGS
T
C
r r1 Outside Diameter Tolerance (Class N) ra
Units : m
Nominal Single Plane Mean Outside
r Outside Diameter ra
B Diameter & D mp Dynamic Equivalent Load
jD jd D (mm) E Series EN Series jDa jda P =X Fr +Y Fa
Over Incl. High Low High Low
Fa/ Fre Fa/ Fr>e
10 + 8 0 0 8 e
10 18 + 8 0 0 8 X Y X Y
18 30 + 9 0 0 9
1 0 0.5 2.5 0.2
30 50 +11 0 0 11
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers Abutment and Fillet Mass
(mm) (N) {kgf} (min 1) Dimensions (mm) (kg)
d D B,C,T r r1 Cr C 0r Cr C 0r Grease Oil

E Series EN Series da Da ra
min. min. min. max. max. approx.
4 16 5 0.15 0.1 1 650 288 168 29 34 000 40 000 E 4 EN 4 5.2 14.8 0.15 0.005
5 16 5 0.15 0.1 1 650 288 168 29 34 000 40 000 E 5 EN 5 6.2 14.8 0.15 0.004
6 21 7 0.3 0.15 2 490 445 254 46 30 000 36 000 E 6 EN 6 8 19 0.3 0.011
7 22 7 0.3 0.15 2 490 445 254 46 30 000 36 000 E 7 EN 7 9 20 0.3 0.013

8 24 7 0.3 0.15 3 450 650 350 66 28 000 34 000 E 8 EN 8 10 22 0.3 0.014
9 28 8 0.3 0.15 4 550 880 465 90 24 000 30 000 E 9 EN 9 11 26 0.3 0.022
10 28 8 0.3 0.15 4 550 880 465 90 24 000 30 000 E 10 EN 10 12 26 0.3 0.021

11 32 7 0.3 0.15 4 400 845 450 86 22 000 26 000 E 11 EN 11 13 30 0.3 0.029
12 32 7 0.3 0.15 4 400 845 450 86 22 000 26 000 E 12 EN 12 14 30 0.3 0.028
13 30 7 0.3 0.15 4 400 845 450 86 22 000 26 000 E 13 EN 13 15 28 0.3 0.021

14 35 8 0.3 0.15 5 800 1 150 590 117 19 000 22 000 EN 14 16 33 0.3 0.035
15 35 8 0.3 0.15 5 800 1 150 590 117 19 000 22 000 E 15 EN 15 17 33 0.3 0.034
40 10 0.6 0.3 7 400 1 500 750 153 17 000 20 000 BO 15 19 36 0.6 0.055
16 38 10 0.6 0.2 6 900 1 380 705 141 17 000 22 000 EN 16 20 34 0.6 0.049
17 40 10 0.6 0.3 7 400 1 500 750 153 17 000 20 000 L 17 21 36 0.6 0.051
44 11 0.6 0.3 7 350 1 500 750 153 16 000 19 000 EN 17 21 40 0.6 0.080
44 11 0.6 0.3 7 350 1 500 750 153 16 000 19 000 BO 17 21 40 0.6 0.080
18 40 9 0.6 0.2 5 050 1 030 515 105 17 000 20 000 EN 18 22 36 0.6 0.051
19 40 9 0.6 0.2 5 050 1 030 515 105 17 000 20 000 E 19 EN 19 23 36 0.6 0.049
20 47 12 1 0.6 11 000 2 380 1 120 243 14 000 17 000 E 20 EN 20 25 42 1 0.089

47 14 1 0.6 11 000 2 380 1 120 243 14 000 17 000 L 20 25 42 1 0.101
Remarks 1. The outside diameters of Magneto Bearings Series E always have plus tolerances.
2. When using Magneto Bearings other than E, please contact NSK.
B 28 B 29
B001-029E.indd 28-29 11/20/13 4:53:48 PM

EXTRA SMALL BALL BEARINGS AND MINIATURE BALL
BEARINGS
EXTRA SMALL BALL BEARINGS MINIATURE BALL BEARINGS
Metric Design Bore Diameter 1 9mm B34
With Flange Bore Diameter 1 9mm B38
Inch Design Bore Diameter 1.016 9.525mm B42
With Flange Bore Diameter 1.191 9.525mm B44
DESIGN AND TYPES

The size ranges of extra small and miniature ball bearings are shown in
Table 1. The design, types, and type symbols are shown in Table 2. Those
types among them that are listed in the bearing tables are indicated by the
shading in Table 2.
Table 1 Size Ranges of Bearings

Units : mm
Design Extra Small Ball Bearings Miniature Ball Bearings
Metric Outside diameter D 9 Outside diameter D < 9

Bore diameter d < 10
Inch Outside diameter D 9.525 Outside diameter D < 9.525

Bore diameter d < 10
Please refer to NSK Miniature Ball Bearings (CAT. No. E126) for details.
ZZ ZZS DD VV
B 30 B 31
B030-045E.indd 30-31 11/20/13 4:54:14 PM

Table 2 Design, Types, and Type Symbols TOLERANCES AND RUNNING ACCURACY
Type Symbols METRIC DESIGN BEARINGS Table 8.2(Pages A60 to A63)
Design Types Special Remarks The flange tolerances for metric design bearings are listed in Table 3.
Metric Inch
Metric Inch Table 3 Flange Tolerances for Metric Flanged Bearings
Shielded sealed (1) Tolerances of Flange Outside Diameter Units : m

6 R MR bearings are Nominal Flange Deviation of Flange Outside Diameter
available. Outside Diameter & D 1S
D1(mm) 1 2
over incl. high low high low
10 +220 36 0 36
10 18 +270 43 0 43
SMT
18 30 +330 52 0 52
Thin section
Remarks 2is applied when the flange outside diameter is used for positioning.
(2) Flange Width Tolerances and Running Accuracies Related to Flange Units : m
Single-Row Deep Groove Ball Bearings
Shielded sealed
F6 FR MF bearings are Variation of Bearing
Nominal Deviation of Variation of Outside Surface Flange Backface
available. Bearing Outside
With flange Flange Width Flange Width& C 1 S Generatrix Inclination Runout with Raceway
Diameter with Flange Backface
D
& C 1S VC 1 S S ea1
S D1
(mm)
Normal and Classes 6,5,4,2 Normal and class 6 Class 5 Class 4 Class 2 Class 5 Class 4 Class 2 Class 5 Class 4 Class 2
Shielded bearings over incl. high low max. max. max.
RW
are available. 2.5(1) 6 Use the &BS tolerance for d Use the & V BS 5 2.5 1.5 8 4 1.5 11 7 3
Extended inner 6 18 of the same bearing of the tolerance for d of 5 2.5 1.5 8 4 1.5 11 7 3
ring the same bearing
18 30 same class of the same class 5 2.5 1.5 8 4 1.5 11 7 3
Notes (1) 2.5 mm is included
Shielded bearings
FRW
With flange are available.
and extended
inner ring
INCH DESIGN BEARINGS Table 8.2 (Pages A60 to A63)
The flange tolerances for inch design flanged bearings are listed in Table 8.8(2)
Shielded bearings (Pages A76 and A77).
SR00X00
are available.
For synchro
motors INSTRUMENT BALL BEARINGS Table 8.8 (Pages A76 to A77)
RECOMMENDED FITS
Pivot Ball
Bearings
BCF
Please refer to NSK Miniature Ball Bearings (CAT.No.E126).
INTERNAL CLEARANCES Table 9.10 (Page A89)

Thrust Ball
Bearings
LIMITING SPEEDS
Remarks Single-row angular contact ball bearings are available besides those shown
above. The limiting speeds listed in the bearing tables should be adjusted depending
on the bearing toad conditions. Also, higher speeds are attainable by making
changes in the lubrication method, cage design, etc. Refer to Page A37 for detailed
information.
B 32 B 33
B030-045E.indd 32-33 11/20/13 4:54:15 PM

Metric Design
B B1
r ra rb
r1
r r1 rb
ra
jD jd jD jd jD a jd a jD b jd b
Shielded Type
Open Type
ZZ ZZ1
(mm) (N) {kgf} (min 1) (mm) (g)
Grease Oil
d D B B1 r (1) r 1(1) Cr C 0r Cr C 0r Open Open
Open Shielded Sealed da db Da Db ra rb approx.
min. min. Z ZZ Z min. max. max. min. max. max. Open Shielded
1 3 1.0 0.05 80 23 8 2.5 130 000 150 000 681 1.4 02.6 0.05 0.03
3 1.5 0.05 80 23 8 2.5 130 000 150 000 MR 31 1.4 02.6 0.05 0.04
4 1.6 0.10 138 35 14 3.5 100 000 120 000 691 1.8 03.2 0.10 0.09
1.2 4 1.8 2.5 0.10 0.10 138 35 14 3.5 110 000 130 000 MR 41 X MR 41 XZZ 2.0 1.9 03.2 03.5 0.10 0.10 0.10 0.14
1.5 4 1.2 2.0 0.05 0.05 112 33 11 3.5 100 000 120 000 681 X 681 XZZ 1.9 2.1 03.6 03.6 0.05 0.05 0.07 0.11
5 2.0 2.6 0.15 0.15 237 69 24 7 85 000 100 000 691 X 691 XZZ 2.7 2.5 03.8 04.3 0.15 0.15 0.17 0.20
6 2.5 3.0 0.15 0.15 330 98 34 10 75 000 90 000 601 X 601 XZZ 2.7 3.0 04.8 05.4 0.15 0.15 0.33 0.38
2 5 1.5 2.3 0.08 0.08 169 50 17 5 85 000 100 000 682 682 ZZ 2.6 2.7 04.4 04.2 0.08 0.08 0.12 0.17
5 2.0 2.5 0.10 0.10 187 58 19 6 85 000 100 000 MR 52 B MR 52 BZZ 2.8 2.7 04.2 04.4 0.10 0.10 0.16 0.23
6 2.3 3.0 0.15 0.15 330 98 34 10 75 000 90 000 692 692 ZZ 3.2 3.0 04.8 05.4 0.15 0.15 0.28 0.38
6 2.5 2.5 0.15 0.15 330 98 34 10 75 000 90 000 MR 62 MR 62 ZZ 3.2 3.0 04.8 05.2 0.15 0.15 0.30 0.29
7 2.5 3.0 0.15 0.15 385 127 39 13 63 000 75 000 MR 72 MR 72 ZZ 3.2 3.8 05.8 06.2 0.15 0.15 0.45 0.49
7 2.8 3.5 0.15 0.15 385 127 39 13 63 000 75 000 602 602 ZZ 3.2 3.8 05.8 06.2 0.15 0.15 0.51 0.58
2.5 6 1.8 2.6 0.08 0.08 208 74 21 7.5 71 000 80 000 682 X 682 XZZ 3.1 3.7 05.4 05.4 0.08 0.08 0.23 0.29
7 2.5 3.5 0.15 0.15 385 127 39 13 63 000 75 000 692 X 692 XZZ 3.7 3.8 05.8 06.2 0.15 0.15 0.41 0.55
8 2.5 0.20 560 179 57 18 60 000 67 000 MR 82 X 4.1 06.4 0.20 0.56
8 2.8 4.0 0.15 0.15 550 175 56 18 60 000 71 000 602 X 602 XZZ 3.7 4.1 06.8 07.0 0.15 0.15 0.63 0.83
3 6 2.0 2.5 0.10 0.10 208 74 21 7.5 71 000 80 000 MR 63 MR 63 ZZ 3.8 3.7 05.2 05.4 0.10 0.10 0.20 0.27
7 2.0 3.0 0.10 0.10 390 130 40 13 63 000 75 000 683 A 683 AZZ 3.8 4.0 06.2 06.4 0.10 0.10 0.32 0.45
8 2.5 0.15 560 179 57 18 60 000 67 000 MR 83 4.2 06.8 0.15 0.54
8 3.0 4.0 0.15 0.15 560 179 57 18 60 000 67 000 693 693 ZZ 4.2 4.3 06.8 07.3 0.15 0.15 0.61 0.83
9 2.5 4.0 0.20 0.15 570 187 58 19 56 000 67 000 MR 93 MR 93 ZZ 4.6 4.3 07.4 07.9 0.20 0.15 0.73 1.18
9 3.0 5.0 0.15 0.15 570 187 58 19 56 000 67 000 603 603 ZZ 4.2 4.3 07.8 07.9 0.15 0.15 0.87 1.45
10 4.0 4.0 0.15 0.15 630 218 64 22 50 000 60 000 623 623 ZZ 4.2 4.3 08.8 08.0 0.15 0.15 1.65 1.66
13 5.0 5.0 0.20 0.20 1 300 485 133 49 40 000 48 000 633 633 ZZ 4.6 6.0 11.4 11.3 0.20 0.20 3.38 3.33
4 7 2.0 0.10 310 115 32 12 60 000 67 000 MR 74 4.8 06.2 0.10 0.22
7 2.5 0.10 255 107 26 11 60 000 71 000 MR 74 ZZ 4.8 06.3 0.10 0.29
8 2.0 3.0 0.15 0.10 395 139 40 14 56 000 67 000 MR 84 MR 84 ZZ 5.2 5.0 06.8 07.4 0.15 0.10 0.36 0.56
9 2.5 4.0 (0.15) (0.15) 640 225 65 23 53 000 63 000 684 A 684 AZZ 4.8 5.2 08.2 08.1 0.10 0.10 0.63 1.01
10 3.0 4.0 0.20 0.15 710 270 73 28 50 000 60 000 MR 104 B MR 104 BZZ 5.6 5.9 08.4 08.8 0.20 0.15 1.04 1.42
11 4.0 4.0 0.15 0.15 960 345 98 35 48 000 56 000 694 694 ZZ 5.2 5.6 09.8 09.9 0.15 0.15 1.7 1.75
12 4.0 4.0 0.20 0.20 960 345 98 35 48 000 56 000 604 604 ZZ 5.6 5.6 10.4 09.9 0.20 0.20 2.25 2.29
13 5.0 5.0 0.20 0.20 1 300 485 133 49 40 000 48 000 624 624 ZZ 5.6 6.0 11.4 11.3 0.20 0.20 3.03 3.04
16 5.0 5.0 0.30 0.30 1 730 670 177 68 36 000 43 000 634 634 ZZ1 6.0 7.5 14.0 13.8 0.30 0.30 5.24 5.21
Note (1) The values in parentheses are not based on ISO 15.
Remarks When using bearings with a rotating outer ring, please contact NSK if they are shielded.
B 34 B 35
B030-045E.indd 34-35 11/20/13 4:54:16 PM

Metric Design
B B1 B1 B1
ra rb
r r1 r1
r1
r r1 r1 r1 ra rb
jD jd jD jd jD jd jD jd jD a jd a jD b jd b
Shielded Type Non-Contact Contact

Open Type
ZZ ZZ1 Sealed Type Sealed Type
VV DD
Boundary Dimensions Basic Load Ratings Limiting Speeds (min 1) Bearing Numbers Abutment and Fillet Dimensions Mass
(mm) (N) {kgf} Grease Oil (mm) (g)
Open
d D B B1 r (1) r1(1) Cr C 0r Cr C 0r Z ZZ D DD Open Open Shielded Sealed da db Da Db ra rb approx.
min. min. V VV Z min. max. max. min. max. max. Open Shielded
5 8 2.0 0.10 310 120 31 12 53 000 63 000 MR 85 05.8 07.2 0.10 00.26
8 2.5 0.10 278 131 28 13 53 000 63 000 MR 85 ZZ 05.8 07.4 0.10 00.34
9 2.5 3.0 0.15 0.15 430 168 44 17 50 000 60 000 MR 95 MR 95 ZZ1 06.2 06.0 07.8 08.2 0.15 0.15 00.50 00.58
10 3.0 4.0 0.15 0.15 430 168 44 17 50 000 60 000 MR 105 MR 105 ZZ 06.2 06.0 08.8 08.4 0.15 0.15 00.95 01.29
11 4.0 0.15 715 276 73 28 48 000 56 000 MR 115 ZZ VV 06.3 09.8 0.15 01.49
11 3.0 5.0 0.15 0.15 715 281 73 29 45 000 53 000 685 685 ZZ 06.2 06.2 09.8 09.9 0.15 0.15 01.20 01.96
13 4.0 4.0 0.20 0.20 1 080 430 110 44 43 000 40 000 50 000 695 695 ZZ VV DD 06.6 06.6 11.4 11.2 0.20 0.20 02.45 02.50
14 5.0 5.0 0.20 0.20 1 330 505 135 52 40 000 38 000 50 000 605 605 ZZ DD 06.6 06.9 12.4 12.2 0.20 0.20 03.54 03.48
16 5.0 5.0 0.30 0.30 1 730 670 177 68 36 000 32 000 43 000 625 625 ZZ1 VV DD 07.0 07.5 14.0 13.8 0.30 0.30 04.95 04.86
19 6.0 6.0 0.30 0.30 2 340 885 238 90 32 000 30 000 40 000 635 635 ZZ1 VV DD 07.0 08.5 17.0 16.5 0.30 0.30 08.56 08.34
6 10 2.5 3.0 0.15 0.10 495 218 51 22 45 000 53 000 MR 106 MR 106 ZZ1 07.2 07.0 08.8 09.3 0.15 0.10 00.56 00.68
12 3.0 4.0 0.20 0.15 715 292 73 30 43 000 40 000 50 000 MR 126 MR 126 ZZ DD 07.6 07.2 10.4 10.9 0.20 0.15 01.27 01.74
13 3.5 5.0 0.15 0.15 1 080 440 110 45 40 000 38 000 50 000 686 A 686 AZZ VV DD 07.2 07.4 11.8 11.7 0.15 0.15 01.91 02.69
15 5.0 5.0 0.20 0.20 1 730 670 177 68 40 000 36 000 45 000 696 696 ZZ1 VV DD 07.6 07.9 13.4 13.3 0.20 0.20 03.88 03.72
17 6.0 6.0 0.30 0.30 2 260 835 231 85 38 000 34 000 45 000 606 606 ZZ VV DD 08.0 08.2 15.0 14.8 0.30 0.30 05.97 06.08
19 6.0 6.0 0.30 0.30 2 340 885 238 90 32 000 30 000 40 000 626 626 ZZ1 VV DD 08.0 08.5 17.0 16.5 0.30 0.30 08.15 07.94
22 7.0 7.0 0.30 0.30 3 300 1 370 335 140 30 000 28 000 36 000 636 636 ZZ VV DD 08.0 10.5 20.0 19.0 0.30 0.30 14.00 14.00
7 11 2.5 3.0 0.15 0.10 455 201 47 21 43 000 50 000 MR 117 MR 117 ZZ 08.2 08.0 09.8 10.5 0.15 0.10 00.62 00.72
13 3.0 4.0 0.20 0.15 540 276 55 28 40 000 48 000 MR 137 MR 137 ZZ 08.6 09.0 11.4 11.6 0.20 0.15 01.58 02.02
14 3.5 5.0 0.15 0.15 1 170 510 120 52 40 000 34 000 45 000 687 687 ZZ1 VV DD 08.2 08.5 12.8 12.7 0.15 0.15 02.13 02.97
17 5.0 5.0 0.30 0.30 1 610 710 164 73 36 000 28 000 43 000 697 697 ZZ1 VV DD 09.0 10.2 15.0 14.8 0.30 0.30 05.26 05.12
19 6.0 6.0 0.30 0.30 2 340 885 238 90 36 000 32 000 43 000 607 607 ZZ1 VV DD 09.0 09.1 17.0 16.5 0.30 0.30 07.67 07.51
22 7.0 7.0 0.30 0.30 3 300 1 370 335 140 30 000 28 000 36 000 627 627 ZZ VV DD 09.0 10.5 20.0 19.0 0.30 0.30 12.70 12.90
26 9.0 9.0 0.30 0.30 4 550 1 970 465 201 28 000 22 000 34 000 637 637 ZZ1 VV DD 09.0 12.8 24.0 22.8 0.30 0.30 24.00 25.00
8 12 2.5 3.5 0.15 0.10 545 274 56 28 40 000 48 000 MR 128 MR 128 ZZ1 09.2 09.0 10.8 11.3 0.15 0.10 00.71 00.97
14 3.5 4.0 0.20 0.15 820 385 83 39 38 000 32 000 45 000 MR 148 MR 148 ZZ VV DD 09.6 09.2 12.4 12.8 0.20 0.15 01.86 02.16
16 4.0 5.0 0.20 0.20 1 610 710 164 73 36 000 28 000 43 000 688 A 688 AZZ1 VV DD 09.6 10.2 14.4 14.2 0.20 0.20 03.12 04.02
19 6.0 6.0 0.30 0.30 2 240 910 228 93 36 000 28 000 43 000 698 698 ZZ VV DD 10.0 10.0 17.0 16.5 0.30 0.30 07.23 07.18
22 7.0 7.0 0.30 0.30 3 300 1 370 335 140 34 000 28 000 40 000 608 608 ZZ VV DD 10.0 10.5 20.0 19.0 0.30 0.30 12.10 12.20
24 8.0 8.0 0.30 0.30 3 350 1 430 340 146 28 000 24 000 34 000 628 628 ZZ VV DD 10.0 12.0 22.0 20.5 0.30 0.30 17.20 17.40
28 9.0 9.0 0.30 0.30 4 550 1 970 465 201 28 000 22 000 34 000 638 638 ZZ1 VV DD 10.0 12.8 26.0 22.8 0.30 0.30 28.30 28.60
9 17 4.0 5.0 0.20 0.20 1 330 665 136 68 36 000 24 000 43 000 689 689 ZZ1 VV DD 10.6 11.5 15.4 15.2 0.20 0.20 03.53 04.43
20 6.0 6.0 0.30 0.30 1 720 840 175 86 34 000 24 000 40 000 699 699 ZZ1 VV DD 11.0 12.0 18.0 17.2 0.30 0.30 08.45 08.33
24 7.0 7.0 0.30 0.30 3 350 1 430 340 146 32 000 24 000 38 000 609 609 ZZ VV DD 11.0 12.0 22.8 20.5 0.30 0.30 14.50 14.70
26 8.0 8.0 (0.6)0 (0.6)0 4 550 1 970 465 201 28 000 22 000 34 000 629 629 ZZ VV DD 11.0 12.8 24.0 22.8 0.30 0.30 19.50 19.30
30 10.00 10.00 0.60 0.60 5 100 2 390 520 244 24 000 30 000 639 639 ZZ VV 13.0 16.1 26.0 25.6 0.60 0.60 36.50 36.00
Remarks 1. When using bearings with a rotating outer ring, please contact NSK if they are sealed or shielded.
2. Bearings with snap rings are also available, please contact NSK.
B 36 B 37
B030-045E.indd 36-37 11/20/13 4:54:17 PM

Metric Design With Flange
B B1 C2
C1
r r1
r r1 ra rb
jD jd jD 1 jD jd jD 2 jda jdb
Shielded Type
Open Type
ZZ ZZ1
(mm) (N) {kgf} (min 1) (mm) (g)
Grease Oil
d D D1 D2 B B1 C1 C2 r (1) r1(1) Cr C 0r Cr C 0r Open Open
Open Shielded Sealed da db ra rb approx.
min. min. Z ZZ Z min. max. max. max. Open Shielded
1 3 03.8 1.0 0.3 0.05 80 23 8 2.5 130 000 150 000 F 681 1.4 0.05 0.04
4 05.0 1.6 0.5 0.10 140 36 14 3.5 100 000 120 000 F 691 1.8 0.10 0.14
1.2 4 04.8 1.8 0.4 0.10 138 35 14 3.5 110 000 130 000 MF 41 X 2.0 0.10 0.12
1.5 4 05.0 05.0 1.2 2.0 0.4 0.6 0.05 0.05 112 33 11 3.5 100 000 120 000 F 681 X F 681 XZZ 1.9 2.1 0.05 0.05 0.09 0.14
5 06.5 06.5 2.0 2.6 0.6 0.8 0.15 0.15 237 69 24 7 85 000 100 000 F 691 X F 691 XZZ 2.7 2.5 0.15 0.15 0.23 0.28
6 07.5 07.5 2.5 3.0 0.6 0.8 0.15 0.15 330 98 34 10 75 000 90 000 F 601 X F 601 XZZ 2.7 3.0 0.15 0.15 0.42 0.52
2 5 06.1 06.1 1.5 2.3 0.5 0.6 0.08 0.08 169 50 17 5 85 000 100 000 F 682 F 682 ZZ 2.6 2.7 0.08 0.08 0.16 0.22
5 06.2 06.2 2.0 2.5 0.6 0.6 0.10 0.10 187 58 19 6 85 000 100 000 MF 52 B MF 52 BZZ 2.8 2.7 0.10 0.10 0.21 0.27
6 07.5 07.5 2.3 3.0 0.6 0.8 0.15 0.15 330 98 34 10 75 000 90 000 F 692 F 692 ZZ 3.2 3.0 0.15 0.15 0.35 0.48
6 07.2 2.5 0.6 0.15 330 98 34 10 75 000 90 000 MF 62 3.2 0.15 0.36
7 08.2 08.2 2.5 3.0 0.6 0.6 0.15 0.15 385 127 39 13 63 000 75 000 MF 72 MF 72 ZZ 3.2 3.8 0.15 0.15 0.52 0.56
7 08.5 08.5 2.8 3.5 0.7 0.9 0.15 0.15 385 127 39 13 63 000 75 000 F 602 F 602 ZZ 3.2 3.1 0.15 0.15 0.60 0.71
2.5 6 07.1 07.1 1.8 2.6 0.5 0.8 0.08 0.08 208 74 21 7.5 71 000 80 000 F 682 X F 682 XZZ 3.1 3.7 0.08 0.08 0.25 0.36
7 08.5 08.5 2.5 3.5 0.7 0.9 0.15 0.15 385 127 39 13 63 000 75 000 F 692 X F 692 XZZ 3.7 3.8 0.15 0.15 0.51 0.68
8 09.2 2.5 0.6 0.20 560 179 57 18 60 000 67 000 MF 82 X 4.1 0.20 0.62
8 09.5 09.5 2.8 4.0 0.7 0.9 0.15 0.15 550 175 56 18 60 000 71 000 F 602 X F 602 XZZ 3.7 3.5 0.15 0.15 0.74 0.98
3 6 07.2 07.2 2.0 2.5 0.6 0.6 0.10 0.10 208 74 21 7.5 71 000 80 000 MF 63 MF 63 ZZ 3.8 3.7 0.10 0.10 0.27 0.33
7 08.1 08.1 2.0 3.0 0.5 0.8 0.10 0.10 390 130 40 13 63 000 75 000 F 683 A F 683 AZZ 3.8 4.0 0.10 0.10 0.37 0.53
8 09.2 2.5 0.6 0.15 560 179 57 18 60 000 67 000 MF 83 4.2 0.15 0.56
8 09.5 09.5 3.0 4.0 0.7 0.9 0.15 0.15 560 179 57 18 60 000 67 000 F 693 F 693 ZZ 4.2 4.3 0.15 0.15 0.70 0.97
9 10.2 10.6 2.5 4.0 0.6 0.8 0.20 0.15 570 187 58 19 56 000 67 000 MF 93 MF 93 ZZ 4.6 4.3 0.20 0.15 0.81 1.34
9 10.5 10.5 3.0 5.0 0.7 1.0 0.15 0.15 570 187 58 19 56 000 67 000 F 603 F 603 ZZ 4.2 4.3 0.15 0.15 1.00 1.63
10 11.5 11.5 4.0 4.0 1.0 1.0 0.15 0.15 630 218 64 22 50 000 60 000 F 623 F 623 ZZ 4.2 4.3 0.15 0.15 1.85 1.86
13 15.0 15.0 5.0 5.0 1.0 1.0 0.20 0.20 1 300 485 133 49 36 000 43 000 F 633 F 633 ZZ 4.6 6.0 0.20 0.20 3.73 3.59
4 7 08.2 2.0 0.6 0.10 310 115 32 12 60 000 67 000 MF 74 4.8 0.10 0.29
7 08.2 2.5 0.6 0.10 255 107 26 11 60 000 71 000 MF 74 ZZ 4.8 0.10 0.35
8 09.2 09.2 2.0 3.0 0.6 0.6 0.15 0.10 395 139 40 14 56 000 67 000 MF 84 MF 84 ZZ 5.2 5.0 0.15 0.10 0.44 0.63
9 10.3 10.3 2.5 4.0 0.6 1.0 (0.15) (0.15) 640 225 65 23 53 000 63 000 F 684 F 684 ZZ 4.8 5.2 0.10 0.10 0.70 1.14
10 11.2 11.6 3.0 4.0 0.6 0.8 0.20 0.15 710 270 73 28 50 000 60 000 MF 104 B MF 104 BZZ 5.6 5.9 0.20 0.15 1.13 1.59
11 12.5 12.5 4.0 4.0 1.0 1.0 0.15 0.15 960 345 98 35 48 000 56 000 F 694 F 694 ZZ 5.2 5.6 0.15 0.15 1.91 1.96
12 13.5 13.5 4.0 4.0 1.0 1.0 0.20 0.20 960 345 98 35 48 000 56 000 F 604 F 604 ZZ 5.6 5.6 0.20 0.20 2.53 2.53
13 15.0 15.0 5.0 5.0 1.0 1.0 0.20 0.20 1 300 485 133 49 40 000 48 000 F 624 F 624 ZZ 5.6 6.0 0.20 0.20 3.38 3.53
16 18.0 18.0 5.0 5.0 1.0 1.0 0.30 0.30 1 730 670 177 68 36 000 43 000 F 634 F 634 ZZ1 6.0 7.5 0.30 0.30 5.73 5.62
B 38 B 39
B030-045E.indd 38-39 11/20/13 4:54:19 PM

Metric Design With Flange
B B1 B1 B1 C2
C1 C2 C2
r1 r1 r1
r
r r1 r1 r1 ra rb
jD jd jD1 jD jd jD2 jD jd jD2 jD jd jD2 jda jdb
Shielded Type Non-Contact Contact

Open Type Sealed Type Sealed Type
ZZ ZZ1
VV DD
Boundary Dimensions Basic Load Ratings Limiting Speeds (min 1) Bearing Numbers Abutment and Fillet Mass
(mm) (N) {kgf} Grease Oil Dimensions (mm) (g)
Open Open
d D D1 D2 B B1 C1 C2 r r1 Cr C 0r C r C 0r Z ZZ D DD Z Open Shielded Sealed da db ra rb approx.
min. min. V VV min. max. max. max. Open Shielded
5 8 09.2 2.0 0.6 0.10 310 120 31 12 53 000 63 000 MF 85 05.8 0.10 00.33
8 09.2 2.5 0.6 0.10 278 131 28 13 53 000 63 000 MF 85 ZZ 05.8 0.10 00.41
9 10.2 10.2 2.5 3.0 0.6 0.6 0.15 0.15 430 168 44 17 50 000 60 000 MF 95 MF 95 ZZ1 06.2 06.0 0.15 0.15 00.59 00.66
10 11.2 11.6 3.0 4.0 0.6 0.8 0.15 0.15 430 168 44 17 50 000 60 000 MF 105 MF 105 ZZ 06.2 06.0 0.15 0.15 01.05 01.46
11 12.5 12.5 3.0 5.0 0.8 1.0 0.15 0.15 715 281 73 29 45 000 53 000 F 685 F 685 ZZ 06.2 06.2 0.15 0.15 01.37 02.18
13 15.0 15.0 4.0 4.0 1.0 1.0 0.20 0.20 1 080 430 110 44 43 000 40 000 50 000 F 695 F 695 ZZ VV DD 06.6 06.6 0.20 0.20 02.79 02.84
14 16.0 16.0 5.0 5.0 1.0 1.0 0.20 0.20 1 330 505 135 52 40 000 38 000 50 000 F 605 F 605 ZZ DD 06.6 06.9 0.20 0.20 03.90 03.85
16 18.0 18.0 5.0 5.0 1.0 1.0 0.30 0.30 1 730 670 177 68 36 000 32 000 43 000 F 625 F 625 ZZ1 VV DD 07.0 07.5 0.30 0.30 05.37 05.27
19 22.0 22.0 6.0 6.0 1.5 1.5 0.30 0.30 2 340 885 238 90 32 000 30 000 40 000 F 635 F 635 ZZ1 VV DD 07.0 08.5 0.30 0.30 09.49 09.49
6 10 11.2 11.2 2.5 3.0 0.6 0.6 0.15 0.10 495 218 51 22 45 000 53 000 MF 106 MF 106 ZZ1 07.2 07.0 0.15 0.10 00.65 00.77
12 13.2 13.6 3.0 4.0 0.6 0.8 0.20 0.15 715 292 73 30 43 000 40 000 50 000 MF 126 MF 126 ZZ DD 07.6 07.2 0.20 0.15 01.38 01.94
13 15.0 15.0 3.5 5.0 1.0 1.1 0.15 0.15 1 080 440 110 45 40 000 38 000 50 000 F 686 A F 686 AZZ VV DD 07.2 07.4 0.15 0.15 02.25 03.04
15 17.0 17.0 5.0 5.0 1.2 1.2 0.20 0.20 1 730 670 177 68 40 000 36 000 45 000 F 696 F 696 ZZ1 VV DD 07.6 07.9 0.20 0.20 04.34 04.26
17 19.0 19.0 6.0 6.0 1.2 1.2 0.30 0.30 2 260 835 231 85 38 000 34 000 45 000 F 606 F 606 ZZ VV DD 08.0 08.2 0.30 0.30 06.58 06.61
19 22.0 22.0 6.0 6.0 1.5 1.5 0.30 0.30 2 340 885 238 90 32 000 30 000 40 000 F 626 F 626 ZZ1 VV DD 08.0 08.5 0.30 0.30 09.09 09.09
22 25.0 25.0 7.0 7.0 1.5 1.5 0.30 0.30 3 300 1 370 335 140 30 000 28 000 36 000 F 636 F 636 ZZ VV DD 08.0 10.5 0.30 0.30 14.60 14.70
7 11 12.2 12.2 2.5 3.0 0.6 0.6 0.15 0.10 455 201 47 21 43 000 50 000 MF 117 MF 117 ZZ 08.2 08.0 0.15 0.10 00.72 00.82
13 14.2 14.6 3.0 4.0 0.6 0.8 0.20 0.15 540 276 55 28 40 000 48 000 MF 137 MF 137 ZZ 08.6 09.0 0.20 0.15 01.70 02.23
14 16.0 16.0 3.5 5.0 1.0 1.1 0.15 0.15 1 170 510 120 52 40 000 34 000 45 000 F 687 F 687 ZZ1 VV DD 08.2 08.5 0.15 0.15 02.48 03.37
17 19.0 19.0 5.0 5.0 1.2 1.2 0.30 0.30 1 610 715 164 73 36 000 28 000 43 000 F 697 F 697 ZZ1 VV DD 09.0 10.2 0.30 0.30 05.65 05.65
19 22.0 22.0 6.0 6.0 1.5 1.5 0.30 0.30 2 340 885 238 90 36 000 32 000 43 000 F 607 F 607 ZZ1 VV DD 09.0 09.1 0.30 0.30 08.66 08.66
22 25.0 25.0 7.0 7.0 1.5 1.5 0.30 0.30 3 300 1 370 335 140 30 000 28 000 36 000 F 627 F 627 ZZ VV DD 09.0 10.5 0.30 0.30 14.20 14.20
8 12 13.2 13.6 2.5 3.5 0.6 0.8 0.15 0.10 545 274 56 28 40 000 48 000 MF 128 MF 128 ZZ1 09.2 09.0 0.15 0.10 00.82 01.15
14 15.6 15.6 3.5 4.0 0.8 0.8 0.20 0.15 820 385 83 39 38 000 32 000 45 000 MF 148 MF 148 ZZ VV DD 09.6 09.2 0.20 0.15 02.09 02.39
16 18.0 18.0 4.0 5.0 1.0 1.1 0.20 0.20 1 610 710 164 73 36 000 30 000 43 000 F 688 A F 688 AZZ VV DD 09.6 10.2 0.20 0.20 03.54 04.47
19 22.0 22.0 6.0 6.0 1.5 1.5 0.30 0.30 2 240 910 228 93 36 000 28 000 43 000 F 698 F 698 ZZ VV DD 10.0 10.0 0.30 0.30 08.35 08.30
22 25.0 25.0 7.0 7.0 1.5 1.5 0.30 0.30 3 300 1 370 335 140 34 000 28 000 40 000 F 608 F 608 ZZ VV DD 10.0 10.5 0.30 0.30 13.40 13.50
9 17 19.0 19.0 4.0 5.0 1.0 1.1 0.20 0.20 1 330 665 136 68 36 000 24 000 43 000 F 689 F 689 ZZ1 VV DD 10.6 11.5 0.20 0.20 03.97 04.91
20 23.0 23.0 6.0 6.0 1.5 1.5 0.30 0.30 1 720 840 175 86 34 000 24 000 40 000 F 699 F 699 ZZ1 VV DD 11.0 12.0 0.30 0.30 09.51 09.51
B 40 B 41
B030-045E.indd 40-41 11/20/13 4:54:20 PM

Inch Design
Bore Diameter 1.016 9.525 mm
B B1
r ra ra
r
r r ra
ra
jD jd jD jd jDa jd a jD b jd b
Shielded Type
Open Type
ZZ ZZS
(mm) (N) {kgf} (min 1) (mm) (g)
Grease Oil
d D B B1 r Cr C 0r Cr C 0r Open Open
Open Shielded da db Da Db ra approx.
min. Z ZZ Z min. max. max. min. max. Open Shielded
1.016 3.175 1.191 0.1 80 23 8 2.5 130 000 150 000 R 09 01.9 02.3 0.1 0.04
1.191 3.967 1.588 2.380 0.1 138 35 14 3.5 110 000 130 000 R0 R 0 ZZ 02.0 01.9 03.1 03.5 0.1 0.09 00.11
1.397 4.762 1.984 2.779 0.1 231 66 24 6.5 90 000 110 000 R1 R 1 ZZ 02.2 02.3 03.9 04.1 0.1 0.15 00.19
1.984 6.350 2.380 3.571 0.1 310 108 32 11 67 000 80 000 R 1-4 R 1-4 ZZ 02.8 03.9 05.5 05.9 0.1 0.35 00.50
2.380 4.762 1.588 0.1 188 60 19 6 80 000 95 000 R 133 03.2 03.9 0.1 0.10
4.762 2.380 0.1 143 52 15 5.5 80 000 95 000 R 133 ZZS 03.0 04.2 0.1 00.13
7.938 2.779 3.571 0.15 550 175 56 18 60 000 71 000 R 1-5 R 1-5 ZZ 03.6 04.1 06.7 07.0 0.15 0.60 00.72
3.175 6.350 2.380 2.779 0.1 283 95 29 9.5 67 000 80 000 R 144 R 144 ZZ 04.0 03.9 05.5 05.9 0.1 0.25 00.27
7.938 2.779 3.571 0.1 560 179 57 18 60 000 67 000 R 2-5 R 2-5 ZZ 04.0 04.3 07.1 07.3 0.1 0.55 00.72
9.525 2.779 3.571 0.15 640 225 65 23 53 000 63 000 R 2-6 R 2-6 ZZS 04.4 04.6 08.3 08.2 0.15 0.96 01.13
9.525 3.967 3.967 0.3 630 218 64 22 56 000 67 000 R2 R 2 ZZ 05.2 04.8 07.5 08.0 0.3 1.36 01.39
12.700 4.366 4.366 0.3 640 225 65 23 53 000 63 000 R 2A R 2A ZZ 05.2 04.6 10.7 08.2 0.3 3.30 03.23
3.967 7.938 2.779 3.175 0.1 360 149 37 15 53 000 63 000 R 155 R 155 ZZS 04.8 05.5 07.1 07.3 0.1 0.51 00.56
4.762 7.938 2.779 3.175 0.1 360 149 37 15 53 000 63 000 R 156 R 156 ZZS 05.6 05.5 07.1 07.3 0.1 0.39 00.42
9.525 3.175 3.175 0.1 710 270 73 28 50 000 60 000 R 166 R 166 ZZ 05.6 05.9 08.7 08.8 0.1 0.81 00.85
12.700 3.967 4.978 0.3 1 300 485 133 49 43 000 53 000 R3 R 3 ZZ 06.8 06.5 10.7 11.2 0.3 2.21 02.79
6.350 9.525 3.175 3.175 0.1 420 204 43 21 48 000 56 000 R 168B R 168 BZZ 07.2 07.0 08.7 08.9 0.1 0.58 00.62
12.700 3.175 4.762 0.15 1 080 440 110 45 40 000 50 000 R 188 R 188 ZZ 07.6 07.4 11.5 11.6 0.15 1.53 02.21
15.875 4.978 4.978 0.3 1 610 660 164 68 38 000 45 000 R 4B R 4B ZZ 08.4 08.4 13.8 13.8 0.3 4.50 04.43
19.050 5.558 7.142 0.4 2 620 1 060 267 108 36 000 43 000 R 4AA R 4AA ZZ 09.4 09.0 16.0 16.6 0.4 7.48 09.17
7.938 12.700 3.967 3.967 0.15 540 276 55 28 40 000 48 000 R 1810 R 1810 ZZ 09.2 09.0 11.5 11.6 0.15 1.56 01.48
9.525 22.225 5.558 7.142 0.4 3 350 1 410 340 144 32 000 38 000 R6 R 6 ZZ 12.6 11.9 19.2 20.0 0.4 9.02 11.00
Remarks 1. When using bearings with a rotating outer ring, please contact NSK if they are shielded.
2. Bearings with double shields (ZZ, ZZS) are also available with single shields (Z, ZS).
B 42 B 43
B030-045E.indd 42-43 11/20/13 4:54:22 PM

Inch Design With Flange
B B1 C2
C1
r r
r r ra ra
jD jd jD 1 jD jd jD 1 jd a jd b
Shielded Type
Open Type
ZZ ZZS
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers Abutment and Fillet Mass
(mm) (N) {kgf} (min 1) Dimensions (mm) (g)
Grease Oil
d D D1 B B1 C1 C2 r Cr C 0r Cr C 0r Open Open
Open Shielded da db ra approx.
min. Z ZZ Z min. max. max. Open Shielded
1.191 3.967 5.156 1.588 2.380 0.330 0.790 0.1 138 35 14 3.5 110 000 130 000 FR 0 FR 0 ZZ 02.0 01.9 0.1 00.11 00.16
1.397 4.762 5.944 1.984 2.779 0.580 0.790 0.1 231 66 24 6.5 90 000 110 000 FR 1 FR 1 ZZ 02.2 02.3 0.1 00.20 00.25
1.984 6.350 7.518 2.380 3.571 0.580 0.790 0.1 310 108 32 11 67 000 80 000 FR 1-4 FR 1-4 ZZ 02.8 03.9 0.1 00.41 00.58
2.380 4.762 5.944 1.588 0.460 0.1 188 60 19 6 80 000 95 000 FR 133 03.2 0.1 00.13
4.762 5.944 2.380 0.790 0.1 143 52 15 5.5 80 000 95 000 FR 133 ZZS 03.0 0.1 00.19
7.938 9.119 2.779 3.571 0.580 0.790 0.15 550 175 56 18 60 000 71 000 FR 1-5 FR 1-5 ZZ 03.6 04.1 0.15 00.68 00.82
3.175 6.350 7.518 2.380 2.779 0.580 0.790 0.1 283 95 29 9.5 67 000 80 000 FR 144 FR 144 ZZ 04.0 03.9 0.1 00.31 00.35
7.938 9.119 2.779 3.571 0.580 0.790 0.1 560 179 57 18 60 000 67 000 FR 2-5 FR 2-5 ZZ 04.0 04.3 0.1 00.62 00.81
9.525 10.719 2.779 3.571 0.580 0.790 0.15 640 225 65 23 53 000 63 000 FR 2-6 FR 2-6 ZZS 04.4 04.6 0.15 01.04 01.25
9.525 11.176 3.967 3.967 0.760 0.760 0.3 630 218 64 22 56 000 67 000 FR 2 FR 2 ZZ 05.2 04.8 0.3 01.51 01.55
3.967 7.938 9.119 2.779 3.175 0.580 0.910 0.1 360 149 37 15 53 000 63 000 FR 155 FR 155 ZZS 04.8 05.5 0.1 00.59 00.67
4.762 7.938 9.119 2.779 3.175 0.580 0.910 0.1 360 149 37 15 53 000 63 000 FR 156 FR 156 ZZS 05.6 05.5 0.1 00.47 00.53
9.525 10.719 3.175 3.175 0.580 0.790 0.1 710 270 73 28 50 000 60 000 FR 166 FR 166 ZZ 05.6 05.9 0.1 00.90 00.98
12.700 14.351 4.978 4.978 1.070 1.070 0.3 1 300 485 133 49 43 000 53 000 FR 3 FR 3 ZZ 06.8 06.5 0.3 02.97 03.09
6.350 9.525 10.719 3.175 3.175 0.580 0.910 0.1 420 204 43 21 48 000 56 000 FR 168B FR 168 BZZ 07.2 07.0 0.1 00.66 00.75
12.700 13.894 3.175 4.762 0.580 1.140 0.15 1 080 440 110 45 40 000 50 000 FR 188 FR 188 ZZ 07.6 07.4 0.15 01.64 02.49
15.875 17.526 4.978 4.978 1.070 1.070 0.3 1 610 660 164 68 38 000 45 000 FR 4B FR 4B ZZ 08.4 08.4 0.3 04.78 04.78
7.938 12.700 13.894 3.967 3.967 0.790 0.790 0.15 540 276 55 28 40 000 48 000 FR 1810 FR 1810 ZZ 09.2 09.0 0.15 01.71 01.63
9.525 22.225 24.613 7.142 7.142 1.570 1.570 0.4 3 350 1 410 340 144 32 000 38 000 FR 6 FR 6 ZZ 12.6 11.9 0.4 10.10 12.10
Remarks 1. When using bearings with a rotating outer ring, please contact NSK if they are shielded.
2. Bearings with double shields (ZZ, ZZS) are also available with single shields (Z, ZS).
B 44 B 45
B030-045E.indd 44-45 11/20/13 4:54:23 PM

ANGULAR CONTACT BALL BEARINGS
SINGLE-ROW AND MATCHED
Bore Diameter 10 65mm B50
DOUBLE-ROW ANGULAR CONTACT Bore Diameter 10 85mm B70

BALL BEARINGS
FOUR-POINT CONTACT BALL BEARINGS

SINGLE-ROW ANGULAR CONTACT BALL BEARINGS
Contact
Since these bearings have a contact angle, they can sustain significant axial
angle
loads in one direction together with radial loads. Because of their design, when
a radial load is applied, an axial force component is produced; therefore, two
opposed bearings or a combination of more than two must be used.
Since the rigidity of single-row angular contact ball bearings can be
increased by preloading, they are often used in the main spindles of machine
tools, for which high running accuracy is required. (Refer to Chapter 10,
Preload, Page A96).
Usually, the cages for angular contact ball bearings with a contact angle
of 30 (Symbol A) or 40(Symbol B) are in accordance with Table 1,but
depending on the application, machined synthetic resin cages or molded
polyamide resin cages are also used. The basic load ratings given in the
bearing tables are based on the cage classification listed in Table 1.
Though the figures in the bearing tables (Pages B50 to B65; bearing bore
diameters of 10 to 120) show bearings with single-shoulder-type inner rings,
both-shoulder-type bearings are also available. Please consult NSK for more
detailed information.
Table 1 Standard Cages for Angular Contact Ball Bearings
Series Pressed Steel Cages Machined Brass Cages
79A5, C 7900 7940

70A 7000 7018 7019 7040
70C 7000 7022
72A, B 7200 7222 7224 7240
72C 7200 7240
73A, B 7300 7320 7321 7340
In addition, for bearings with the same serial number, if the type of cages
are different, the number of balls may also be different. In such a case, the
load rating will differ from the one listed in the bearing tables.
Angular Contact Ball Bearings with contact angles of 15 (Symbol C) and
25 (Symbol A5) are primarily for high precision or high speed applications,
and machined brass or synthetic resin cages or molded polyamide cages are
used.
The maximum operating temperature of molded polyamide cages is 120C.
B 46 B 47
B046-075E.indd 46-47 11/20/13 4:55:02 PM

MATCHED ANGULAR CONTACT BALL BEARINGS TOLERANCES AND RUNNING ACCURACY
The types and features of matched angular contact ball bearings are shown SINGLE-ROW ANGULAR CONTACT
in Table 2. BALL BEARINGS Table 8.2 (Pages A60 to A63)
NSKHPS ANGULAR CONTACT BALL BEARINGS
Table 2 Types and Features of Matched Angular Contact Ball Bearings Tolerance for Dimensions: Class 6,
Running Accuracy: Class 5 Table 8.2 (Pages A60 to A63)
Figure Arrangement Features MATCHED ANGULAR CONTACT
BALL BEARINGS Table 8.2 (Pages A60 to A63)
Back-to-back Radial loads and axial loads in both directions DOUBLE-ROW ANGULAR CONTACT
(DB) can be sustained. BALL BEARINGS Table 8.2 (Pages A60 to A63)
Since the distance between the effective FOUR-POINT CONTACT BALL
(Example) load centers a0 is big, this type is suitable if BEARINGS Table 8.2 (Pages A60 to A63)
7208 A DB moments are applied.
a0 RECOMMENDED FITS
SINGLE-ROW ANGULAR CONTACT BALL
Radial loads and axial loads in both directions BEARINGS AND HPS ANGULAR CONTACT
Face-to-face
can be sustained. BALL BEARINGS Table 9.2 (Page A84)
(DF) Compared with the DB Type, the distance Table 9.4 (Page A85)
(Example) between the effective load centers is small, so
the capacity to sustain moments is inferior to
MATCHED ANGULAR CONTACT BALL BEARINGS Table 9.2 (Page A84)
a0 7208 B DF the DB Type.
DOUBLE-ROW ANGULAR CONTACT BALL
BEARINGS Table 9.2 (Page A84)
Tandem Table 9.4 (Page A85)
Radial loads and axial loads in one direction
(DT) can be sustained. Since two bearings share the FOUR-POINT CONTACT BALL BEARINGSTable 9.2 (Page A84)
(Example) axial load, this arrangement is used when the Table 9.4 (Page A85)
7208 A DT
load in one direction is heavy. INTERNAL CLEARANCES
MATCHED ANGULAR CONTACT BALL BEARINGS Table 9. 17 (Page A94)
Matched angular contact ball bearings with precision better than P5 are primarily
NSKHPS ANGULAR CONTACT BALL BEARINGS used in the main spindles of machine tools, so they are used with a preload for
In comparison with standard angular contact ball bearings, these bearings rigidity. For convenience of selection, internal clearances are adjusted to produce Very
have high capacity, high limiting speed, and highly accurate universal Light, Light, Medium, and Heavy Preloads. Their fitting is also special. Concerning
matching as the features. The molded polyamide cages are standard these matters, please refer to Tables 10.1 and 10.2 (Pages A98 and A99).
specification for the HPS type. The clearance (or preload) of matched bearings is obtained by axially tightening
a pair of bearings till the side faces of their inner or outer rings are pressed against
DOUBLE-ROW ANGULAR CONTACT BALL BEARINGS each other.
This is basically a back-to-back mounting of two single-row angular contact NSKHPS ANGULAR CONTACT BALL BEARINGS
ball bearings, but their inner and outer rings are each integrated into one.
Axial loads in both directions can be sustained, and the capacity to sustain Axial Internal Clearance (Measured Clearances) Units : m
moments is good. This type is used as fixed-end bearings. Nominal Bore Diameter Axial Internal Clearance
Their cages are pressed steel. d (mm) CNB GA
over incl. min. max. min. max.
FOUR-POINT CONTACT BALL BEARINGS 12 18 17 25
18 30 20 28 2 6
The inner ring is split radially into two pieces. Their design allows one 30 50 24 32
bearing to sustain significant axial loads in either direction. 50 80 29 41 3 9
The contact angle is 35, so the axial load capacity is high. This type is
suitable for carrying pure axial loads or combined loads where the axial loads DOUBLE-ROW ANGULAR CONTACT BALL BEARINGS
are high.
The cages are made of machined brass. For the clearance in double-row angular contact ball bearings, please consult with
NSK.
PRECAUTIONS FOR USE OF ANGULAR CONTACT BALL FOUR-POINT CONTACT BALL BEARINGSTable 9.18 (Page A94)
BEARINGS LIMITING SPEEDS
Under severe operating conditions where the speed and temperature are In cases of single-row and matched angular contact ball bearings, the Limiting
close to their limits, lubrication is marginal, vibration and moment loads are speeds listed in the bearing table are for bearings with machined cage. For those with
heavy, they may not be suitable, particularly for certain types of cages. In pressed cages, the listed speeds must be reduced by 20%.
such a case, please consult with NSK beforehand. The limiting speeds of bearings with contact angles of 15 (Symbol C) and
And if the load on angular contact ball bearings becomes too small, or if the 25 (Symbol A5) are for bearings with precision of P5 and better (with machined
ratio of the axial and radial loads for matched bearings exceeds e (e is listed synthetic-resin cages or molded polyamide cages).
in the bearings tables) during operation, slippage occurs between the balls The limiting speeds listed in the bearing tables should be adjusted depending on the
and raceways, which may result in smearing. Especially with large bearings bearing load conditions. Also, higher speeds are attainable by making changes in the
since the weight of the balls and cage is high. If such load conditions are lubrication method, cage design, etc. Refer to Page A37 for detailed information.
expected, please consult with NSK for selection of the bearings.
B 48 B 49
B046-075E.indd 48-49 11/20/13 4:55:03 PM

Dynamic Equivalent Load P = X Fr +Y Fa
SINGLE/MATCHED MOUNTINGS
Single, DT DB or DF
Bore Diameter 10 15 mm Contact i f0 Fa*
e Fa/Fre Fa/Fr>e Fa/Fre Fa/Fr>e
Angle Cor
B 2B 2B 2B X Y X Y X Y X Y
r 0.178 0.38 1 0 0.44 1.47 1 1.65 0.72 2.39
r1 ra rb ra 0.357 0.40 1 0 0.44 1.40 1 1.57 0.72 2.28
0.714 0.43 1 0 0.44 1.30 1 1.46 0.72 2.11
1.07 0.46 1 0 0.44 1.23 1 1.38 0.72 2.00
15
r1 1.43 0.47 1 0 0.44 1.19 1 1.34 0.72 1.93
r ra ra rb 2.14 0.50 1 0 0.44 1.12 1 1.26 0.72 1.82
3.57 0.55 1 0 0.44 1.02 1 1.14 0.72 1.66
0.56 1 0 0.44 1.00 1 1.12 0.72 1.63
jD jd jDa jd a jD b jd a jDa jd b 25
5.35
0.68 1 0 0.41 0.87 1 0.92 0.67 1.41
30 0.80 1 0 0.39 0.76 1 0.78 0.63 1.24
a0 a0 40 1.14 1 0 0.35 0.57 1 0.55 0.57 0.93
* For i , use 2 for DB, DF and 1 for DT
Static Equivalent Load P0=X 0Fr +Y 0Fa

Contact Single, DT DB or DF
Angle X0 Y0 X0 Y0 Single or DT
a 15 0.5 0.46 1 0.92 mounting
When
25 0.5 0.38 1 0.76 F r >0.5F r +Y 0 F a
Single Back-to-Back Face-to-Face Tandem 30 0.5 0.33 1 0.66 use P0=Fr
DB DF DT 40 0.5 0.26 1 0.52
Boundary Dimensions Basic Load Ratings (Single) Factor Limiting Eff.Load Abutment and Fillet Mass Bearing Numbers (2) Basic Load Ratings (Matched) Limiting Load Center Abutment and Fillet
(mm) (N) {kgf} Speeds (1) Centers Dimensions (mm) (kg) (N) {kgf} Speeds (1) (Matched) Spacings (mm) Dimensions (mm)
(min 1) (mm) (min 1) a0
d D B r r1 Cr C 0r Cr C 0r f0 Grease Oil a da Da ra Single Duplex Cr C 0r Cr C 0r Grease Oil DB DF db (3) Db rb (3)
min. min. min. max. max. approx. min. max. max.
10 22 6 0.3 0.15 2 880 1 450 294 148 40 000 56 000 6.7 12.5 19.5 0.3 0.009 7900 A5 DB DF DT 4 700 2 900 475 296 32 000 43 000 13.5 1.5 20.8 0.15
22 6 0.3 0.15 3 000 1 520 305 155 14.1 48 000 63 000 5.1 12.5 19.5 0.3 0.009 7900 C DB DF DT 4 900 3 050 500 310 38 000 53 000 10.3 1.7 20.8 0.15
26 8 0.3 0.15 5 350 2 600 550 266 32 000 43 000 9.2 12.5 23.5 0.3 0.019 7000 A DB DF DT 8 750 5 200 890 530 24 000 34 000 18.4 2.4 11.2 24.8 0.15
26 8 0.3 0.15 5 300 2 490 540 254 12.6 45 000 63 000 6.4 12.5 23.5 0.3 0.021 7000 C DB DF DT 8 650 5 000 880 510 36 000 50 000 12.8 3.2 24.8 0.15
30 9 0.6 0.3 5 400 2 710 555 276 28 000 38 000 10.3 15 25 0.6 0.032 7200 A DB DF DT 8 800 5 400 900 555 22 000 30 000 20.5 2.5 12.5 27.5 0.3
30 9 0.6 0.3 5 000 2 500 510 255 20 000 28 000 12.9 15 25 0.6 0.032 7200 B DB DF DT 8 100 5 000 825 510 16 000 22 000 25.8 7.8 12.5 27.5 0.3
30 9 0.6 0.3 5 400 2 610 550 266 13.2 40 000 56 000 7.2 15 25 0.6 0.036 7200 C DB DF DT 8 800 5 200 895 530 32 000 45 000 14.4 3.6 27.5 0.3
35 11 0.6 0.3 9 300 4 300 950 440 20 000 26 000 12.0 15 30 0.6 0.053 7300 A DB DF DT 15 100 8 600 1 540 880 16 000 22 000 24.0 2.0 12.5 32.5 0.3
35 11 0.6 0.3 8 750 4 050 890 410 18 000 24 000 14.9 15 30 0.6 0.054 7300 B DB DF DT 14 200 8 100 1 450 825 14 000 20 000 29.9 7.9 12.5 32.5 0.3
12 24 6 0.3 0.15 3 200 1 770 325 181 38 000 53 000 7.2 14.5 21.5 0.3 0.011 7901 A5 DB DF DT 5 200 3 550 530 360 30 000 43 000 14.4 2.4 22.8 0.15
24 6 0.3 0.15 3 350 1 860 340 189 14.7 45 000 63 000 5.4 14.5 21.5 0.3 0.011 7901 C DB DF DT 5 450 3 700 555 380 36 000 50 000 10.8 1.2 22.8 0.15
28 8 0.3 0.15 5 800 2 980 590 305 28 000 38 000 9.8 14.5 25.5 0.3 0.021 7001 A DB DF DT 9 400 5 950 955 610 22 000 30 000 19.5 3.5 13.2 26.8 0.15
28 8 0.3 0.15 5 800 2 900 590 296 13.2 40 000 56 000 6.7 14.5 25.5 0.3 0.024 7001 C DB DF DT 9 400 5 800 960 590 32 000 45 000 13.4 2.6 26.8 0.15
32 10 0.6 0.3 8 000 4 050 815 410 26 000 34 000 11.4 17 27 0.6 0.037 7201 A DB DF DT 13 000 8 050 1 330 820 20 000 28 000 22.7 2.7 14.5 29.5 0.3
32 10 0.6 0.3 7 450 3 750 760 380 18 000 26 000 14.2 17 27 0.6 0.038 7201 B DB DF DT 12 100 7 500 1 230 765 15 000 20 000 28.5 8.5 14.5 29.5 0.3
32 10 0.6 0.3 8 150 3 750 830 380 20 000 30 000 14.2 17 27 0.6 0.036 *7201 BEA 16 000 24 000 28.5 8.5 14.5 29.5 0.3
32 10 0.6 0.3 7 900 3 850 805 395 12.5 36 000 50 000 7.9 17 27 0.6 0.041 7201 C DB DF DT 12 800 7 700 1 310 785 30 000 40 000 15.9 4.1 29.5 0.3
37 12 1 0.6 9 450 4 500 965 460 18 000 24 000 13.1 18 31 1 0.060 7301 A DB DF DT 15 400 9 000 1 570 915 15 000 20 000 26.1 2.1 17 32 0.6
37 12 1 0.6 8 850 4 200 900 425 16 000 22 000 16.3 18 31 1 0.062 7301 B DB DF DT 14 400 8 400 1 460 855 13 000 18 000 32.6 8.6 17 32 0.6
37 12 1 0.6 11 100 4 950 1 130 505 18 000 26 000 16.3 18 31 1 0.061 *7301 BEA 15 000 22 000 32.6 8.6 17 32 0.6
15 28 7 0.3 0.15 4 550 2 530 465 258 32 000 43 000 8.5 17.5 25.5 0.3 0.015 7902 A5 DB DF DT 7 400 5 050 755 515 26 000 34 000 17.0 3.0 26.8 0.15
28 7 0.3 0.15 4 750 2 640 485 270 14.5 38 000 53 000 6.4 17.5 25.5 0.3 0.015 7902 C DB DF DT 7 750 5 300 790 540 30 000 43 000 12.8 1.2 26.8 0.15
32 9 0.3 0.15 6 100 3 450 625 350 24 000 32 000 11.3 17.5 29.5 0.3 0.030 7002 A DB DF DT 9 950 6 850 1 010 700 19 000 26 000 22.6 4.6 16.2 30.8 0.15
32 9 0.3 0.15 6 250 3 400 635 345 14.1 34 000 48 000 7.6 17.5 29.5 0.3 0.034 7002 C DB DF DT 10 100 6 750 1 030 690 28 000 38 000 15.3 2.7 30.8 0.15
35 11 0.6 0.3 8 650 4 650 880 475 22 000 30 000 12.7 20 30 0.6 0.045 7202 A DB DF DT 14 000 9 300 1 430 950 18 000 24 000 25.4 3.4 17.5 32.5 0.3
35 11 0.6 0.3 7 950 4 300 810 440 16 000 22 000 16.0 20 30 0.6 0.046 7202 B DB DF DT 12 900 8 600 1 310 875 13 000 18 000 32.0 10.0 17.5 32.5 0.3
35 11 0.6 0.3 9 800 4 800 995 490 18 000 26 000 16.0 20 30 0.6 0.044 *7202 BEA 14 000 20 000 32.0 10.0 17.5 32.5 0.3
35 11 0.6 0.3 8 650 4 550 885 460 13.2 32 000 45 000 8.8 20 30 0.6 0.052 7202 C DB DF DT 14 100 9 050 1 440 925 26 000 36 000 17.7 4.3 32.5 0.3
42 13 1 0.6 13 400 7 100 1 370 720 16 000 22 000 14.7 21 36 1 0.084 7302 A DB DF DT 21 800 14 200 2 220 1 440 13 000 17 000 29.5 3.5 20 37 0.6
42 13 1 0.6 12 500 6 600 1 270 670 14 000 19 000 18.5 21 36 1 0.086 7302 B DB DF DT 20 200 13 200 2 060 1 340 11 000 15 000 36.9 10.9 20 37 0.6
42 13 1 0.6 14 300 6 900 1 460 705 16 000 22 000 18.5 21 36 1 0.084 *7302 BEA 13 000 18 000 36.9 10.9 20 37 0.6
Notes (1) For applications operating near the limiting speed, refer to Page B49. Note (3) For bearings marked in the column for db, db and rb for shafts are da (min) and ra (max) respectively.
(2) The suffixes A, A5, B, and C represent contact angles of 30, 25, 40, and 15 respectively. Remarks The bearings denoted by an asterisk (*) are NSKHPS Angular contact ball bearings and the column of Duplex in Bearing
Numbers indicates the universal matching.
B 50 B 51
B046-075E.indd 50-51 11/20/13 4:55:04 PM

Single, DT DB or DF
Angle Cor
r 0.178 0.38 1 0 0.44 1.47 1 1.65 0.72 2.39
r1 ra rb ra 0.357 0.40 1 0 0.44 1.40 1 1.57 0.72 2.28
0.714 0.43 1 0 0.44 1.30 1 1.46 0.72 2.11
1.07 0.46 1 0 0.44 1.23 1 1.38 0.72 2.00
15
r1 1.43 0.47 1 0 0.44 1.19 1 1.34 0.72 1.93
r ra ra rb 2.14 0.50 1 0 0.44 1.12 1 1.26 0.72 1.82
3.57 0.55 1 0 0.44 1.02 1 1.14 0.72 1.66
0.56 1 0 0.44 1.00 1 1.12 0.72 1.63
5.35
0.68 1 0 0.41 0.87 1 0.92 0.67 1.41
30 0.80 1 0 0.39 0.76 1 0.78 0.63 1.24
a0 a0 40 1.14 1 0 0.35 0.57 1 0.55 0.57 0.93

a 15 0.5 0.46 1 0.92 mounting
When
25 0.5 0.38 1 0.76 F r >0.5F r +Y 0 F a
DB DF DT 40 0.5 0.26 1 0.52
(min 1) (mm) (min 1) a0
17 30 7 0.3 0.15 4 750 2 800 485 286 30 000 40 000 9.0 19.5 27.5 0.3 0.017 7903 A5 DB DF DT 7 750 5 600 790 570 24 000 32 000 18.0 4.0 28.8 0.15
30 7 0.3 0.15 5 000 2 940 510 299 14.8 34 000 48 000 6.6 19.5 27.5 0.3 0.017 7903 C DB DF DT 8 150 5 850 830 600 28 000 38 000 13.3 0.7 28.8 0.15
35 10 0.3 0.15 6 400 3 800 655 390 22 000 30 000 12.5 19.5 32.5 0.3 0.040 7003 A DB DF DT 10 400 7 650 1 060 780 17 000 24 000 25.0 5.0 18.2 33.8 0.15
35 10 0.3 0.15 6 600 3 800 675 390 14.5 32 000 43 000 8.5 19.5 32.5 0.3 0.044 7003 C DB DF DT 10 700 7 600 1 100 775 26 000 34 000 17.0 3.0 33.8 0.15
40 12 0.6 0.3 10 800 6 000 1 100 610 20 000 28 000 14.2 22 35 0.6 0.067 7203 A DB DF DT 17 600 12 000 1 790 1 220 16 000 22 000 28.5 4.5 19.5 37.5 0.3
40 12 0.6 0.3 9 950 5 500 1 010 565 14 000 19 000 18.0 22 35 0.6 0.068 7203 B DB DF DT 16 100 11 000 1 650 1 130 11 000 15 000 35.9 11.9 19.5 37.5 0.3
40 12 0.6 0.3 11 600 6 100 1 180 625 16 000 22 000 18.2 22 35 0.6 0.065 *7203 BEA 13 000 18 000 36.3 12.3 19.5 37.5 0.3
40 12 0.6 0.3 10 900 5 850 1 110 595 13.3 28 000 38 000 9.8 22 35 0.6 0.075 7203 C DB DF DT 17 600 11 700 1 800 1 190 22 000 32 000 19.6 4.4 37.5 0.3
47 14 1 0.6 15 900 8 650 1 630 880 14 000 19 000 16.2 23 41 1 0.116 7303 A DB DF DT 25 900 17 300 2 640 1 760 11 000 15 000 32.5 4.5 22 42 0.6
47 14 1 0.6 14 800 8 000 1 510 820 13 000 17 000 20.4 23 41 1 0.118 7303 B DB DF DT 24 000 16 000 2 450 1 640 10 000 14 000 40.9 12.9 22 42 0.6
47 14 1 0.6 16 800 8 300 1 720 850 14 000 20 000 20.4 23 41 1 0.113 *7303 BEA 11 000 16 000 40.9 12.9 22 42 0.6
20 37 9 0.3 0.15 6 600 4 050 675 410 24 000 32 000 11.1 22.5 34.5 0.3 0.036 7904 A5 DB DF DT 10 700 8 100 1 090 825 19 000 26 000 22.3 4.3 35.8 0.15
37 9 0.3 0.15 6 950 4 250 710 430 14.9 28 000 38 000 8.3 22.5 34.5 0.3 0.036 7904 C DB DF DT 11 300 8 500 1 150 865 22 000 32 000 16.6 1.4 35.8 0.15
42 12 0.6 0.3 10 800 6 600 1 110 670 18 000 24 000 14.9 25 37 0.6 0.068 7004 A DB DF DT 17 600 13 200 1 800 1 340 15 000 20 000 29.9 5.9 22.5 39.5 0.3
42 12 0.6 0.3 11 100 6 550 1 130 665 14.0 26 000 36 000 10.1 25 37 0.6 0.076 7004 C DB DF DT 18 000 13 100 1 840 1 330 20 000 30 000 20.3 3.7 39.5 0.3
47 14 1 0.6 14 500 8 300 1 480 845 17 000 22 000 16.7 26 41 1 0.106 7204 A DB DF DT 23 500 16 600 2 400 1 690 13 000 19 000 33.3 5.3 25 42 0.6
47 14 1 0.6 13 300 7 650 1 360 780 12 000 16 000 21.1 26 41 1 0.109 7204 B DB DF DT 21 600 15 300 2 210 1 560 9 500 13 000 42.1 14.1 25 42 0.6
47 14 1 0.6 15 600 8 150 1 590 830 13 000 19 000 21.1 26 41 1 0.103 *7204 BEA 11 000 16 000 42.1 14.1 25 42 0.6
47 14 1 0.6 14 600 8 050 1 480 825 13.3 24 000 34 000 11.5 26 41 1 0.118 7204 C DB DF DT 23 600 16 100 2 410 1 650 19 000 26 000 23.0 5.0 42 0.6
52 15 1.1 0.6 18 700 10 400 1 910 1 060 13 000 17 000 17.9 27 45 1 0.146 7304 A DB DF DT 30 500 20 800 3 100 2 130 10 000 13 000 35.8 5.8 25 47 0.6
52 15 1.1 0.6 17 300 9 650 1 770 985 11 000 15 000 22.6 27 45 1 0.15 7304 B DB DF DT 28 200 19 300 2 870 1 970 9 000 12 000 45.2 15.2 25 47 0.6
52 15 1.1 0.6 19 800 10 500 2 020 1 070 13 000 18 000 22.6 27 45 1 0.149 *7304 BEA 10 000 14 000 45.2 15.2 25 47 0.6
25 42 9 0.3 0.15 7 450 5 150 760 525 20 000 28 000 12.3 27.5 39.5 0.3 0.043 7905 A5 DB DF DT 12 100 10 300 1 230 1 050 16 000 22 000 24.6 6.6 40.8 0.15
42 9 0.3 0.15 7 850 5 400 800 555 15.5 24 000 34 000 9.0 27.5 39.5 0.3 0.042 7905 C DB DF DT 12 700 10 800 1 300 1 110 19 000 26 000 18.0 0.0 40.8 0.15
47 12 0.6 0.3 11 300 7 400 1 150 750 16 000 22 000 16.4 30 42 0.6 0.079 7005 A DB DF DT 18 300 14 800 1 870 1 510 13 000 17 000 32.8 8.8 27.5 44.5 0.3
47 12 0.6 0.3 11 700 7 400 1 190 755 14.7 22 000 30 000 10.8 30 42 0.6 0.089 7005 C DB DF DT 19 000 14 800 1 940 1 510 18 000 26 000 21.6 2.4 44.5 0.3
52 15 1 0.6 16 200 10 300 1 650 1 050 15 000 20 000 18.6 31 46 1 0.13 7205 A DB DF DT 26 300 20 500 2 690 2 090 12 000 16 000 37.2 7.2 30 47 0.6
52 15 1 0.6 14 800 9 400 1 510 960 10 000 14 000 23.7 31 46 1 0.133 7205 B DB DF DT 24 000 18 800 2 450 1 920 8 500 11 000 47.3 17.3 30 47 0.6
52 15 1 0.6 17 600 10 200 1 790 1 040 12 000 17 000 23.7 31 46 1 0.127 *7205 BEA 9 500 14 000 47.3 17.3 30 47 0.6
52 15 1 0.6 16 600 10 200 1 690 1 040 14.0 22 000 28 000 12.7 31 46 1 0.143 7205 C DB DF DT 27 000 20 400 2 750 2 080 17 000 24 000 25.3 4.7 47 0.6
62 17 1.1 0.6 26 400 15 800 2 690 1 610 10 000 14 000 21.1 32 55 1 0.235 7305 A DB DF DT 43 000 31 500 4 400 3 250 8 500 11 000 42.1 8.1 30 57 0.6
Notes (1) For applications operating near the limiting speed, refer to Page B49. Note (3) For bearings marked in the column for db, db and rb for shafts are da (min) and ra (max) respectively.
B 52 B 53
B046-075E.indd 52-53 11/20/13 4:55:05 PM

Single, DT DB or DF
Angle Cor
r 0.178 0.38 1 0 0.44 1.47 1 1.65 0.72 2.39
r1 ra rb ra 0.357 0.40 1 0 0.44 1.40 1 1.57 0.72 2.28
0.714 0.43 1 0 0.44 1.30 1 1.46 0.72 2.11
1.07 0.46 1 0 0.44 1.23 1 1.38 0.72 2.00
15
r1 1.43 0.47 1 0 0.44 1.19 1 1.34 0.72 1.93
r ra ra rb 2.14 0.50 1 0 0.44 1.12 1 1.26 0.72 1.82
3.57 0.55 1 0 0.44 1.02 1 1.14 0.72 1.66
0.56 1 0 0.44 1.00 1 1.12 0.72 1.63
5.35
0.68 1 0 0.41 0.87 1 0.92 0.67 1.41
30 0.80 1 0 0.39 0.76 1 0.78 0.63 1.24
a0 a0 40 1.14 1 0 0.35 0.57 1 0.55 0.57 0.93

a 15 0.5 0.46 1 0.92 mounting
When
25 0.5 0.38 1 0.76 F r >0.5F r +Y 0 F a
DB DF DT 40 0.5 0.26 1 0.52
(min 1) (mm) (min 1) a0
25 62 17 1.1 0.6 24 400 14 600 2 490 1 490 9 000 13 000 26.7 32 55 1 0.241 7305 B DB DF DT 39 500 29 300 4 050 2 980 7 500 10 000 53.5 19.5 30 57 0.6
62 17 1.1 0.6 27 200 14 900 2 770 1 520 10 000 15 000 26.8 32 55 1 0.229 *7305 BEA 8 500 12 000 53.5 19.5 30 57 0.6
30 47 9 0.3 0.15 7 850 5 950 800 605 18 000 24 000 13.5 32.5 44.5 0.3 0.049 7906 A5 DB DF DT 12 800 11 900 1 300 1 210 14 000 19 000 27.0 9.0 45.8 0.15
47 9 0.3 0.15 8 300 6 250 845 640 15.9 22 000 28 000 9.7 32.5 44.5 0.3 0.049 7906 C DB DF DT 13 500 12 500 1 380 1 280 17 000 24 000 19.3 1.3 45.8 0.15
55 13 1 0.6 14 500 10 100 1 480 1 030 13 000 18 000 18.8 36 49 1 0.116 7006 A DB DF DT 23 600 20 200 2 410 2 060 11 000 15 000 37.5 11.5 35 50 0.6
55 13 1 0.6 15 100 10 300 1 540 1 050 14.9 19 000 26 000 12.2 36 49 1 0.134 7006 C DB DF DT 24 600 20 500 2 510 2 090 15 000 22 000 24.4 1.6 50 0.6
62 16 1 0.6 22 500 14 800 2 300 1 510 12 000 17 000 21.3 36 56 1 0.197 7206 A DB DF DT 36 500 29 500 3 750 3 000 10 000 13 000 42.6 10.6 35 57 0.6
62 16 1 0.6 20 500 13 500 2 090 1 380 8 500 12 000 27.3 36 56 1 0.202 7206 B DB DF DT 33 500 27 000 3 400 2 760 7 100 9 500 54.6 22.6 35 57 0.6
62 16 1 0.6 23 700 14 300 2 420 1 460 10 000 14 000 27.3 36 56 1 0.194 *7206 BEA 8 000 11 000 54.6 22.6 35 57 0.6
62 16 1 0.6 23 000 14 700 2 350 1 500 13.9 18 000 24 000 14.2 36 56 1 0.222 7206 C DB DF DT 37 500 29 300 3 800 2 990 14 000 20 000 28.3 3.7 57 0.6
72 19 1.1 0.6 33 500 20 900 3 450 2 130 9 000 12 000 24.2 37 65 1 0.346 7306 A DB DF DT 54 500 41 500 5 600 4 250 7 100 9 500 48.4 10.4 35 67 0.6
72 19 1.1 0.6 31 000 19 300 3 150 1 960 8 000 11 000 30.9 37 65 1 0.354 7306 B DB DF DT 50 500 38 500 5 150 3 950 6 300 8 500 61.8 23.8 35 67 0.6
72 19 1.1 0.6 36 500 20 600 3 700 2 100 9 000 13 000 30.9 37 65 1 0.336 *7306 BEA 7 100 10 000 61.8 23.8 35 67 0.6
35 55 10 0.6 0.3 11 400 8 700 1 170 885 15 000 20 000 15.5 40 50 0.6 0.074 7907 A5 DB DF DT 18 600 17 400 1 890 1 770 12 000 17 000 31.0 11.0 52.5 0.3
55 10 0.6 0.3 12 100 9 150 1 230 930 15.7 18 000 24 000 11.0 40 50 0.6 0.074 7907 C DB DF DT 19 600 18 300 2 000 1 860 14 000 20 000 22.1 2.1 52.5 0.3
62 14 1 0.6 18 300 13 400 1 870 1 370 12 000 16 000 21.0 41 56 1 0.153 7007 A DB DF DT 29 700 26 800 3 050 2 740 9 500 13 000 42.0 14.0 40 57 0.6
62 14 1 0.6 19 100 13 700 1 950 1 390 15.0 17 000 22 000 13.5 41 56 1 0.173 7007 C DB DF DT 31 000 27 300 3 150 2 790 13 000 19 000 27.0 1.0 57 0.6
72 17 1.1 0.6 29 700 20 100 3 050 2 050 10 000 14 000 23.9 42 65 1 0.287 7207 A DB DF DT 48 500 40 000 4 900 4 100 8 500 12 000 47.9 13.9 40 67 0.6
72 17 1.1 0.6 27 100 18 400 2 760 1 870 7 500 10 000 30.9 42 65 1 0.294 7207 B DB DF DT 44 000 36 500 4 500 3 750 6 000 8 000 61.9 27.9 40 67 0.6
72 17 1.1 0.6 32 500 19 600 3 300 1 990 8 500 12 000 30.9 42 65 1 0.271 *7207BEA 6 700 9 500 61.9 27.9 40 67 0.6
72 17 1.1 0.6 30 500 19 900 3 100 2 030 13.9 15 000 20 000 15.7 42 65 1 0.32 7207 C DB DF DT 49 500 40 000 5 050 4 050 12 000 17 000 31.3 2.7 67 0.6
80 21 1.5 1 40 000 26 300 4 050 2 680 8 000 10 000 27.1 44 71 1.5 0.464 7307 A DB DF DT 65 000 52 500 6 600 5 350 6 300 8 500 54.2 12.2 41 74 1
80 21 1.5 1 36 500 24 200 3 750 2 460 7 100 9 500 34.6 44 71 1.5 0.474 7307 B DB DF DT 59 500 48 500 6 100 4 950 5 600 7 500 69.2 27.2 41 74 1
80 21 1.5 1 40 500 24 400 4 100 2 490 8 000 11 000 34.6 44 71 1.5 0.451 *7307 BEA 6 300 9 000 69.2 27.2 41 74 1
40 62 12 0.6 0.3 14 300 11 200 1 460 1 140 14 000 18 000 17.9 45 57 0.6 0.11 7908 A5 DB DF DT 23 300 22 300 2 370 2 270 11 000 15 000 35.8 11.8 59.5 0.3
62 12 0.6 0.3 15 100 11 700 1 540 1 200 15.7 16 000 22 000 12.8 45 57 0.6 0.109 7908 C DB DF DT 24 600 23 500 2 510 2 390 13 000 18 000 25.7 1.7 59.5 0.3
68 15 1 0.6 19 500 15 400 1 990 1 570 10 000 14 000 23.1 46 62 1 0.19 7008 A DB DF DT 31 500 31 000 3 250 3 150 8 500 11 000 46.2 16.2 45 63 0.6
68 15 1 0.6 20 600 15 900 2 100 1 620 15.4 15 000 20 000 14.7 46 62 1 0.213 7008 C DB DF DT 33 500 32 000 3 400 3 250 12 000 17 000 29.5 0.5 63 0.6
80 18 1.1 0.6 35 500 25 100 3 600 2 560 9 500 13 000 26.3 47 73 1 0.375 7208 A DB DF DT 57 500 50 500 5 850 5 150 7 500 10 000 52.6 16.6 45 75 0.6
80 18 1.1 0.6 32 000 23 000 3 250 2 340 6 700 9 000 34.2 47 73 1 0.383 7208 B DB DF DT 52 000 46 000 5 300 4 700 5 300 7 500 68.3 32.3 45 75 0.6
Notes (1) For applications operating near the limiting speed, refer to Page B49. Note (3) For bearings marked in the column for db, db and rb for shafts are da (min.) and ra (max.) respectively.
B 54 B 55
B046-075E.indd 54-55 11/20/13 4:55:06 PM

Single, DT DB or DF
Angle Cor
r 0.178 0.38 1 0 0.44 1.47 1 1.65 0.72 2.39
r1 ra rb ra 0.357 0.40 1 0 0.44 1.40 1 1.57 0.72 2.28
0.714 0.43 1 0 0.44 1.30 1 1.46 0.72 2.11
1.07 0.46 1 0 0.44 1.23 1 1.38 0.72 2.00
15
r1 1.43 0.47 1 0 0.44 1.19 1 1.34 0.72 1.93
r ra ra rb 2.14 0.50 1 0 0.44 1.12 1 1.26 0.72 1.82
3.57 0.55 1 0 0.44 1.02 1 1.14 0.72 1.66
0.56 1 0 0.44 1.00 1 1.12 0.72 1.63
5.35
0.68 1 0 0.41 0.87 1 0.92 0.67 1.41
30 0.80 1 0 0.39 0.76 1 0.78 0.63 1.24
a0 a0 40 1.14 1 0 0.35 0.57 1 0.55 0.57 0.93

a 15 0.5 0.46 1 0.92 mounting
When
25 0.5 0.38 1 0.76 F r >0.5F r +Y 0 F a
DB DF DT 40 0.5 0.26 1 0.52
(min 1) (mm) (min 1) a0
40 80 18 1.1 0.6 38 500 24 500 3 900 2 500 7 500 11 000 34.2 47 73 1 0.357 *7208 BEA 6 000 8 500 68.3 32.3 45 75 0.6
80 18 1.1 0.6 36 500 25 200 3 700 2 570 14.1 14 000 19 000 17.0 47 73 1 0.418 7208 C DB DF DT 59 000 50 500 6 000 5 150 11 000 15 000 34.1 1.9 75 0.6
90 23 1.5 1 49 000 33 000 5 000 3 350 7 100 9 000 30.3 49 81 1.5 0.633 7308 A DB DF DT 79 500 66 000 8 100 6 700 5 600 7 500 60.5 14.5 46 84 1
90 23 1.5 1 45 000 30 500 4 550 3 100 6 300 8 500 38.8 49 81 1.5 0.648 7308 B DB DF DT 73 000 60 500 7 400 6 200 5 000 6 700 77.5 31.5 46 84 1
90 23 1.5 1 53 000 33 000 5 400 3 350 7 100 10 000 38.8 49 81 1.5 0.619 *7308 BEA 5 600 8 000 77.5 31.5 46 84 1
45 68 12 0.6 0.3 15 100 12 700 1 540 1 290 12 000 17 000 19.2 50 63 0.6 0.13 7909 A5 DB DF DT 24 600 25 400 2 510 2 590 9 500 13 000 38.4 14.4 65.5 0.3
68 12 0.6 0.3 16 000 13 400 1 630 1 360 16.0 14 000 20 000 13.6 50 63 0.6 0.129 7909 C DB DF DT 26 000 26 800 2 660 2 730 12 000 16 000 27.1 3.1 65.5 0.3
75 16 1 0.6 23 100 18 700 2 360 1 910 9 500 13 000 25.3 51 69 1 0.25 7009 A DB DF DT 37 500 37 500 3 850 3 800 7 500 10 000 50.6 18.6 50 70 0.6
75 16 1 0.6 24 400 19 300 2 490 1 960 15.4 14 000 19 000 16.0 51 69 1 0.274 7009 C DB DF DT 39 500 38 500 4 050 3 950 11 000 15 000 32.1 0.1 70 0.6
85 19 1.1 0.6 39 500 28 700 4 050 2 930 8 500 12 000 28.3 52 78 1 0.411 7209 A DB DF DT 64 500 57 500 6 550 5 850 7 100 9 500 56.5 18.5 50 80 0.6
85 19 1.1 0.6 36 000 26 200 3 650 2 680 6 300 8 500 36.8 52 78 1 0.421 7209 B DB DF DT 58 500 52 500 5 950 5 350 5 000 6 700 73.5 35.5 50 80 0.6
85 19 1.1 0.6 40 500 27 100 4 100 2 760 7 100 10 000 36.8 52 78 1 0.40 *7209 BEA 5 600 8 000 73.5 35.5 50 80 0.6
85 19 1.1 0.6 41 000 28 800 4 150 2 940 14.2 12 000 17 000 18.2 52 78 1 0.468 7209 C DB DF DT 66 500 57 500 6 750 5 850 10 000 14 000 36.4 1.6 80 0.6
100 25 1.5 1 63 500 43 500 6 450 4 450 6 300 8 500 33.4 54 91 1.5 0.848 7309 A DB DF DT 103 000 87 000 10 500 8 900 5 000 6 700 66.9 16.9 51 94 1
100 25 1.5 1 58 500 40 000 5 950 4 100 5 600 7 500 42.9 54 91 1.5 0.869 7309 B DB DF DT 95 000 80 500 9 650 8 200 4 500 6 000 85.8 35.8 51 94 1
100 25 1.5 1 62 500 39 500 6 400 4 050 6 300 9 000 42.9 54 91 1.5 0.823 *7309 BEA 5 000 7 100 85.8 35.8 51 94 1
50 72 12 0.6 0.3 15 900 14 200 1 630 1 450 11 000 15 000 20.2 55 67 0.6 0.132 7910 A5 DB DF DT 25 900 28 400 2 640 2 900 9 000 12 000 40.5 16.5 69.5 0.3
72 12 0.6 0.3 16 900 15 000 1 720 1 530 16.2 13 000 18 000 14.2 55 67 0.6 0.13 7910 C DB DF DT 27 400 30 000 2 800 3 050 11 000 15 000 28.3 4.3 69.5 0.3
80 16 1 0.6 24 500 21 100 2 500 2 150 8 500 12 000 26.8 56 74 1 0.263 7010 A DB DF DT 40 000 42 000 4 050 4 300 7 100 9 500 53.5 21.5 55 75 0.6
80 16 1 0.6 26 000 21 900 2 650 2 230 15.7 12 000 17 000 16.7 56 74 1 0.293 7010 C DB DF DT 42 000 44 000 4 300 4 450 10 000 14 000 33.4 1.4 75 0.6
90 20 1.1 0.6 41 500 31 500 4 200 3 200 8 000 11 000 30.2 57 83 1 0.466 7210 A DB DF DT 67 000 63 000 6 850 6 400 6 300 9 000 60.4 20.4 55 85 0.6
90 20 1.1 0.6 37 500 28 600 3 800 2 920 5 600 8 000 39.4 57 83 1 0.477 7210 B DB DF DT 60 500 57 000 6 200 5 850 4 500 6 300 78.7 38.7 55 85 0.6
90 20 1.1 0.6 42 000 29 700 4 300 3 050 6 300 9 500 39.4 57 83 1 0.453 *7210 BEA 5 000 7 500 78.7 38.7 55 85 0.6
90 20 1.1 0.6 43 000 31 500 4 350 3 250 14.5 12 000 16 000 19.4 57 83 1 0.528 7210 C DB DF DT 69 500 63 500 7 100 6 450 9 500 13 000 38.7 1.3 85 0.6
110 27 2 1 74 000 52 000 7 550 5 300 5 600 7 500 36.6 60 100 2 1.1 7310 A DB DF DT 121 000 104 000 12 300 10 600 4 500 6 000 73.2 19.2 56 104 1
110 27 2 1 68 000 48 000 6 950 4 900 5 000 6 700 47.1 60 100 2 1.12 7310 B DB DF DT 111 000 96 000 11 300 9 800 4 000 5 600 94.1 40.1 56 104 1
110 27 2 1 78 000 50 500 7 950 5 150 5 600 8 000 47.1 60 100 2 1.07 *7310 BEA 4 500 6 700 94.1 40.1 56 104 1
55 80 13 1 0.6 18 100 16 800 1 840 1 710 10 000 14 000 22.2 61 74 1 0.184 7911 A5 DB DF DT 29 300 33 500 2 990 3 400 8 000 11 000 44.5 18.5 75 0.6
80 13 1 0.6 19 100 17 700 1 950 1 810 16.3 12 000 16 000 15.5 61 74 1 0.182 7911 C DB DF DT 31 000 35 500 3 150 3 600 9 500 13 000 31.1 5.1 75 0.6
90 18 1.1 0.6 32 500 27 700 3 300 2 830 7 500 11 000 29.9 62 83 1 0.391 7011 A DB DF DT 52 500 55 500 5 350 5 650 6 300 8 500 59.9 23.9 60 85 0.6
B 56 B 57
B046-075E.indd 56-57 11/20/13 4:55:08 PM

Dynamic Equivalent Load = r+ a
Single, DT DB or DF
Bore Diameter 55 65 mm Contact 0 a*
a/ r a/ r> a/ r a/ r>
Angle Cor
B 2B 2B 2B
r 0.178 0.38 1 0 0.44 1.47 1 1.65 0.72 2.39
r1 ra rb ra 0.357 0.40 1 0 0.44 1.40 1 1.57 0.72 2.28
0.714 0.43 1 0 0.44 1.30 1 1.46 0.72 2.11
1.07 0.46 1 0 0.44 1.23 1 1.38 0.72 2.00
15
r1 1.43 0.47 1 0 0.44 1.19 1 1.34 0.72 1.93
r ra ra rb 2.14 0.50 1 0 0.44 1.12 1 1.26 0.72 1.82
3.57 0.55 1 0 0.44 1.02 1 1.14 0.72 1.66
0.56 1 0 0.44 1.00 1 1.12 0.72 1.63
5.35
0.68 1 0 0.41 0.87 1 0.92 0.67 1.41
30 0.80 1 0 0.39 0.76 1 0.78 0.63 1.24
a0 a0 40 1.14 1 0 0.35 0.57 1 0.55 0.57 0.93
* For , use 2 for DB, DF and 1 for DT
Static Equivalent Load 0= 0 r+ 0 a
Angle 0 0 0 0 Single or DT
a 15 0.5 0.46 1 0.92 mounting
When
25 0.5 0.38 1 0.76
Single Back-to-Back Face-to-Face Tandem r >0.5 r + 0 a
30 0.5 0.33 1 0.66 use 0= r
DB DF DT 40 0.5 0.26 1 0.52
(min 1) (mm) (min 1) a0
d D B r r1 Cr C 0r Cr C 0r 0
Grease Oil a da Da ra Single Duplex Cr C 0r Cr C 0r Grease Oil DB DF db (3) Db rb (3)
55 90 18 1.1 0.6 34 000 28 600 3 500 2 920 15.5 11 000 15 000 18.7 62 83 1 0.43 7011 C DB DF DT 55 500 57 500 5 650 5 850 9 000 12 000 37.4 1.4 85 0.6
100 21 1.5 1 51 000 39 500 5 200 4 050 7 100 10 000 32.9 64 91 1.5 0.613 7211 A DB DF DT 83 000 79 000 8 450 8 050 6 000 8 000 65.7 23.7 61 94 1
100 21 1.5 1 46 500 36 000 4 700 3 700 5 300 7 100 43.0 64 91 1.5 0.627 7211 B DB DF DT 75 000 72 000 7 650 7 350 4 000 5 600 86.0 44.0 61 94 1
100 21 1.5 1 51 500 37 000 5 250 3 800 6 000 8 500 43.0 64 91 1.5 0.596 *7211 BEA 4 500 6 700 86.0 44.0 61 94 1
100 21 1.5 1 53 000 40 000 5 400 4 100 14.5 10 000 14 000 20.9 64 91 1.5 0.688 7211 C DB DF DT 86 000 80 000 8 800 8 150 8 500 12 000 41.7 0.3 94 1
120 29 2 1 86 000 61 500 8 750 6 250 5 000 6 700 39.8 65 110 2 1.41 7311 A DB DF DT 139 000 123 000 14 200 12 500 4 000 5 600 79.5 21.5 61 114 1
120 29 2 1 79 000 56 500 8 050 5 750 4 500 6 300 51.2 65 110 2 1.45 7311 B DB DF DT 128 000 113 000 13 100 11 500 3 600 5 000 102.4 44.4 61 114 1
120 29 2 1 89 000 58 500 9 100 6 000 5 000 7 500 51.2 65 110 2 1.36 *7311 BEA 4 000 6 000 102.4 44.4 61 114 1
60 85 13 1 0.6 18 300 17 700 1 870 1 810 9 500 13 000 23.4 66 79 1 0.197 7912 A5 DB DF DT 29 800 35 500 3 050 3 600 7 500 10 000 46.8 20.8 80 0.6
85 13 1 0.6 19 400 18 700 1 980 1 910 16.5 11 000 15 000 16.2 66 79 1 0.194 7912 C DB DF DT 31 500 37 500 3 200 3 800 9 000 12 000 32.4 6.4 80 0.6
95 18 1.1 0.6 33 000 29 500 3 350 3 000 7 100 10 000 31.4 67 88 1 0.417 7012 A DB DF DT 53 500 59 000 5 450 6 000 6 000 8 000 62.7 26.7 65 90 0.6
95 18 1.1 0.6 35 000 30 500 3 600 3 150 15.7 10 000 14 000 19.4 67 88 1 0.46 7012 C DB DF DT 57 000 61 500 5 800 6 250 8 500 12 000 38.8 2.8 90 0.6
110 22 1.5 1 62 000 48 500 6 300 4 950 6 700 9 000 35.5 69 101 1.5 0.798 7212 A DB DF DT 100 000 97 500 10 200 9 950 5 300 7 100 71.1 27.1 66 104 1
110 22 1.5 1 56 000 44 500 5 700 4 550 4 800 6 300 46.7 69 101 1.5 0.815 7212 B DB DF DT 91 000 89 000 9 300 9 050 3 800 5 300 93.3 49.3 66 104 1
110 22 1.5 1 61 500 45 000 6 300 4 600 5 300 7 500 46.7 69 101 1.5 0.791 *7212 BEA 4 300 6 000 93.3 49.3 66 104 1
110 22 1.5 1 64 000 49 000 6 550 5 000 14.4 9 500 13 000 22.4 69 101 1.5 0.889 7212 C DB DF DT 104 000 98 500 10 600 10 000 7 500 11 000 44.8 0.8 104 1
130 31 2.1 1.1 98 000 71 500 10 000 7 250 4 800 6 300 42.9 72 118 2 1.74 7312 A DB DF DT 159 000 143 000 16 200 14 500 3 800 5 000 85.9 23.9 67 123 1
130 31 2.1 1.1 90 000 65 500 9 200 6 700 4 300 5 600 55.4 72 118 2 1.78 7312 B DB DF DT 146 000 131 000 14 900 13 400 3 400 4 500 110.7 48.7 67 123 1
130 31 2.1 1.1 102 000 68 500 10 500 7 000 4 800 6 700 55.4 72 118 2 1.7 *7312 BEA 3 800 5 600 110.7 48.7 67 123 1
65 90 13 1 0.6 19 100 19 400 1 940 1 980 9 000 12 000 24.6 71 84 1 0.211 7913 A5 DB DF DT 31 000 39 000 3 150 3 950 7 100 9 500 49.1 23.1 85 0.6
90 13 1 0.6 20 200 20 500 2 060 2 090 16.7 10 000 14 000 16.9 71 84 1 0.208 7913 C DB DF DT 33 000 41 000 3 350 4 200 8 500 12 000 33.8 7.8 85 0.6
100 18 1.1 0.6 35 000 33 000 3 550 3 350 6 700 9 500 32.8 72 93 1 0.455 7013 A DB DF DT 56 500 65 500 5 750 6 700 5 600 7 500 65.6 29.6 70 95 0.6
100 18 1.1 0.6 37 000 34 500 3 800 3 500 15.9 10 000 13 000 20.0 72 93 1 0.493 7013 C DB DF DT 60 500 68 500 6 150 7 000 8 000 11 000 40.1 4.1 95 0.6
120 23 1.5 1 70 500 58 000 7 150 5 900 6 000 8 500 38.2 74 111 1.5 1.03 7213 A DB DF DT 114 000 116 000 11 600 11 800 4 800 6 700 76.4 30.4 71 114 1
120 23 1.5 1 63 500 52 500 6 500 5 350 4 300 6 000 50.3 74 111 1.5 1.05 7213 B DB DF DT 103 000 105 000 10 500 10 700 3 400 4 800 100.6 54.6 71 114 1
120 23 1.5 1 70 000 53 500 7 150 5 450 4 800 7 100 50.3 74 111 1.5 1.01 *7213 BEA 3 800 5 600 100.6 54.6 71 114 1
120 23 1.5 1 73 000 58 500 7 450 6 000 14.6 9 000 12 000 23.9 74 111 1.5 1.14 7213 C DB DF DT 119 000 117 000 12 100 12 000 7 100 9 500 47.8 1.8 114 1
140 33 2.1 1.1 111 000 82 000 11 300 8 350 4 300 6 000 46.1 77 128 2 2.12 7313 A DB DF DT 180 000 164 000 18 400 16 700 3 600 4 800 92.2 26.2 72 133 1
140 33 2.1 1.1 102 000 75 500 10 400 7 700 3 800 5 300 59.5 77 128 2 2.17 7313 B DB DF DT 166 000 151 000 16 900 15 400 3 200 4 300 119.0 53.0 72 133 1
140 33 2.1 1.1 114 000 77 000 11 600 7 850 4 300 6 300 59.5 77 128 2 2.09 *7313 BEA 3 600 5 000 119.0 53.0 72 133 1
B 58 B 59
B046-075E.indd 58-59 11/20/13 4:55:09 PM

Single, DT DB or DF
Angle Cor
r 0.178 0.38 1 0 0.44 1.47 1 1.65 0.72 2.39
r1 ra rb ra 0.357 0.40 1 0 0.44 1.40 1 1.57 0.72 2.28
0.714 0.43 1 0 0.44 1.30 1 1.46 0.72 2.11
1.07 0.46 1 0 0.44 1.23 1 1.38 0.72 2.00
15
r1 1.43 0.47 1 0 0.44 1.19 1 1.34 0.72 1.93
r ra ra rb 2.14 0.50 1 0 0.44 1.12 1 1.26 0.72 1.82
3.57 0.55 1 0 0.44 1.02 1 1.14 0.72 1.66
0.56 1 0 0.44 1.00 1 1.12 0.72 1.63
5.35
0.68 1 0 0.41 0.87 1 0.92 0.67 1.41
30 0.80 1 0 0.39 0.76 1 0.78 0.63 1.24
a0 a0 40 1.14 1 0 0.35 0.57 1 0.55 0.57 0.93

a 15 0.5 0.46 1 0.92 mounting
When
25 0.5 0.38 1 0.76 F r >0.5F r +Y 0 F a
DB DF DT 40 0.5 0.26 1 0.52
(min 1) (mm) (min 1) a0
70 100 16 1 0.6 26 500 26 300 2 710 2 680 8 000 11 000 27.8 76 94 1 0.341 7914 A5 DB DF DT 43 000 52 500 4 400 5 350 6 300 9 000 55.6 23.6 95 0.6
100 16 1 0.6 28 100 27 800 2 870 2 830 16.4 9 500 13 000 19.4 76 94 1 0.338 7914 C DB DF DT 45 500 55 500 4 650 5 650 7 500 11 000 38.8 6.8 95 0.6
110 20 1.1 0.6 44 000 41 500 4 500 4 200 6 300 8 500 36.0 77 103 1 0.625 7014 A DB DF DT 71 500 82 500 7 300 8 450 5 000 6 700 72.0 32.0 75 105 0.6
110 20 1.1 0.6 47 000 43 000 4 800 4 400 15.7 9 000 12 000 22.1 77 103 1 0.698 7014 C DB DF DT 76 000 86 000 7 750 8 750 7 100 10 000 44.1 4.1 105 0.6
125 24 1.5 1 76 500 63 500 7 800 6 500 5 600 8 000 40.1 79 116 1.5 1.11 7214 A DB DF DT 124 000 127 000 12 600 13 000 4 500 6 300 80.3 32.3 76 119 1
125 24 1.5 1 69 000 58 000 7 050 5 900 4 000 5 600 52.9 79 116 1.5 1.14 7214 B DB DF DT 112 000 116 000 11 500 11 800 3 200 4 500 105.8 57.8 76 119 1
125 24 1.5 1 75 500 58 500 7 700 6 000 4 500 6 700 52.9 79 116 1.5 1.08 *7214 BEA 3 600 5 300 105.8 57.8 76 119 1
125 24 1.5 1 79 500 64 500 8 100 6 600 14.6 8 500 11 000 25.1 79 116 1.5 1.24 7214 C DB DF DT 129 000 129 000 13 200 13 200 6 700 9 000 50.1 2.1 119 1
150 35 2.1 1.1 125 000 93 500 12 700 9 550 4 000 5 300 49.3 82 138 2 2.6 7314 A DB DF DT 203 000 187 000 20 700 19 100 3 200 4 300 98.5 28.5 77 143 1
150 35 2.1 1.1 114 000 86 000 11 700 8 750 3 600 5 000 63.6 82 138 2 2.65 7314 B DB DF DT 186 000 172 000 19 000 17 500 2 800 4 000 127.3 57.3 77 143 1
150 35 2.1 1.1 124 000 87 500 12 600 8 900 4 000 6 000 63.7 82 138 2 2.53 *7314 BEA 3 200 4 800 127.3 57.3 77 143 1
75 105 16 1 0.6 26 900 27 700 2 750 2 820 7 500 10 000 29.0 81 99 1 0.355 7915 A5 DB DF DT 44 000 55 500 4 450 5 650 6 000 8 500 58.0 26.0 100 0.6
105 16 1 0.6 28 600 29 300 2 910 2 980 16.6 9 000 12 000 20.1 81 99 1 0.357 7915 C DB DF DT 46 500 58 500 4 750 5 950 7 100 10 000 40.1 8.1 100 0.6
115 20 1.1 0.6 45 000 43 500 4 600 4 450 6 000 8 000 37.4 82 108 1 0.661 7015 A DB DF DT 73 000 87 500 7 450 8 900 4 800 6 700 74.8 34.8 80 110 0.6
115 20 1.1 0.6 48 000 45 500 4 900 4 650 15.9 8 500 12 000 22.7 82 108 1 0.748 7015 C DB DF DT 78 000 91 500 7 950 9 300 6 700 9 500 45.4 5.4 110 0.6
130 25 1.5 1 76 000 64 500 7 750 6 550 5 600 7 500 42.1 84 121 1.5 1.19 7215 A DB DF DT 123 000 129 000 12 600 13 100 4 300 6 000 84.2 34.2 81 124 1
130 25 1.5 1 68 500 58 500 7 000 5 950 3 800 5 300 55.5 84 121 1.5 1.22 7215 B DB DF DT 112 000 117 000 11 400 11 900 3 200 4 300 111.0 61.0 81 124 1
130 25 1.5 1 78 500 63 500 8 000 6 450 4 300 6 300 55.5 84 121 1.5 1.18 *7215 BEA 3 600 5 000 111.0 61.0 81 124 1
130 25 1.5 1 83 000 70 000 8 450 7 100 14.8 8 000 11 000 26.2 84 121 1.5 1.36 7215 C DB DF DT 134 000 140 000 13 700 14 200 6 300 9 000 52.4 2.4 124 1
160 37 2.1 1.1 136 000 106 000 13 800 10 800 3 800 5 000 52.4 87 148 2 3.13 7315 A DB DF DT 221 000 212 000 22 500 21 600 3 000 4 000 104.8 30.8 82 153 1
160 37 2.1 1.1 125 000 97 500 12 700 9 900 3 400 4 800 67.8 87 148 2 3.19 7315 B DB DF DT 202 000 195 000 20 600 19 800 2 800 3 800 135.6 61.6 82 153 1
80 110 16 1 0.6 27 300 29 000 2 790 2 960 7 100 10 000 30.2 86 104 1 0.38 7916 A5 DB DF DT 44 500 58 000 4 550 5 900 5 600 8 000 60.3 28.3 105 0.6
110 16 1 0.6 29 000 30 500 2 960 3 150 16.7 8 500 12 000 20.7 86 104 1 0.376 7916 C DB DF DT 47 000 61 500 4 800 6 250 6 700 9 500 41.5 9.5 105 0.6
125 22 1.1 0.6 55 000 53 000 5 650 5 400 5 600 7 500 40.6 87 118 1 0.88 7016 A DB DF DT 89 500 106 000 9 150 10 800 4 300 6 000 81.2 37.2 85 120 0.6
125 22 1.1 0.6 58 500 55 500 6 000 5 650 15.7 8 000 11 000 24.7 87 118 1 0.966 7016 C DB DF DT 95 500 111 000 9 700 11 300 6 300 9 000 49.4 5.4 120 0.6
140 26 2 1 89 000 76 000 9 100 7 750 5 000 7 100 44.8 90 130 2 1.46 7216 A DB DF DT 145 000 152 000 14 700 15 600 4 000 5 600 89.5 37.5 86 134 1
140 26 2 1 80 500 69 500 8 200 7 050 3 600 5 000 59.1 90 130 2 1.49 7216 B DB DF DT 131 000 139 000 13 300 14 100 2 800 4 000 118.3 66.3 86 134 1
140 26 2 1 87 500 70 000 8 950 7 150 4 000 6 000 59.2 90 130 2 1.42 *7216 BEA 3 200 4 800 118.3 66.3 86 134 1
140 26 2 1 93 000 77 500 9 450 7 900 14.7 7 500 10 000 27.7 90 130 2 1.63 7216 C DB DF DT 151 000 155 000 15 400 15 800 6 000 8 000 55.5 3.5 134 1
170 39 2.1 1.1 147 000 119 000 15 000 12 100 3 600 4 800 55.6 92 158 2 3.71 7316 A DB DF DT 239 000 238 000 24 400 24 200 2 800 3 800 111.2 33.2 87 163 1
170 39 2.1 1.1 135 000 109 000 13 800 11 100 3 200 4 300 71.9 92 158 2 3.79 7316 B DB DF DT 219 000 218 000 22 400 22 300 2 600 3 400 143.9 65.9 87 163 1
B 60 B 61
B046-075E.indd 60-61 11/20/13 4:55:10 PM

Single, DT DB or DF
Angle Cor
r 0.178 0.38 1 0 0.44 1.47 1 1.65 0.72 2.39
r1 ra rb ra 0.357 0.40 1 0 0.44 1.40 1 1.57 0.72 2.28
0.714 0.43 1 0 0.44 1.30 1 1.46 0.72 2.11
1.07 0.46 1 0 0.44 1.23 1 1.38 0.72 2.00
15
r1 1.43 0.47 1 0 0.44 1.19 1 1.34 0.72 1.93
r ra ra rb 2.14 0.50 1 0 0.44 1.12 1 1.26 0.72 1.82
3.57 0.55 1 0 0.44 1.02 1 1.14 0.72 1.66
0.56 1 0 0.44 1.00 1 1.12 0.72 1.63
5.35
0.68 1 0 0.41 0.87 1 0.92 0.67 1.41
30 0.80 1 0 0.39 0.76 1 0.78 0.63 1.24
a0 a0 40 1.14 1 0 0.35 0.57 1 0.55 0.57 0.93

a 15 0.5 0.46 1 0.92 mounting
When
25 0.5 0.38 1 0.76 F r >0.5F r +Y 0 F a
DB DF DT 40 0.5 0.26 1 0.52
(min 1) (mm) (min 1) a0
85 120 18 1.1 0.6 36 500 38 500 3 750 3 900 6 700 9 000 32.9 92 113 1 0.541 7917 A5 DB DF DT 59 500 77 000 6 100 7 850 5 300 7 500 65.8 29.8 115 0.6
120 18 1.1 0.6 39 000 40 500 3 950 4 150 16.5 8 000 11 000 22.7 92 113 1 0.534 7917 C DB DF DT 63 000 81 500 6 450 8 300 6 300 9 000 45.5 9.5 115 0.6
130 22 1.1 0.6 56 500 56 000 5 750 5 700 5 300 7 100 42.0 92 123 1 0.913 7017 A DB DF DT 91 500 112 000 9 350 11 400 4 300 5 600 84.1 40.1 90 125 0.6
130 22 1.1 0.6 60 000 58 500 6 150 6 000 15.9 7 500 10 000 25.4 92 123 1 1.01 7017 C DB DF DT 98 000 117 000 9 950 12 000 6 000 8 500 50.8 6.8 125 0.6
150 28 2 1 103 000 89 000 10 500 9 100 4 800 6 700 47.9 95 140 2 1.83 7217 A DB DF DT 167 000 178 000 17 100 18 200 3 800 5 300 95.8 39.8 91 144 1
150 28 2 1 93 000 81 000 9 500 8 250 3 400 4 800 63.3 95 140 2 1.87 7217 B DB DF DT 151 000 162 000 15 400 16 500 2 800 3 800 126.6 70.6 91 144 1
150 28 2 1 107 000 90 500 10 900 9 250 14.7 6 700 9 500 29.7 95 140 2 2.04 7217 C DB DF DT 174 000 181 000 17 800 18 500 5 600 7 500 59.5 3.5 144 1
180 41 3 1.1 159 000 133 000 16 200 13 500 3 400 4 500 58.8 99 166 2.5 4.33 7317 A DB DF DT 258 000 265 000 26 300 27 000 2 600 3 600 117.5 35.5 92 173 1
180 41 3 1.1 146 000 122 000 14 800 12 400 3 000 4 000 76.1 99 166 2.5 4.42 7317 B DB DF DT 236 000 244 000 24 100 24 800 2 400 3 200 152.2 70.2 92 173 1
90 125 18 1.1 0.6 39 500 43 500 4 000 4 450 6 300 8 500 34.1 97 118 1 0.56 7918 A5 DB DF DT 64 000 87 000 6 500 8 900 5 000 7 100 68.1 32.1 120 0.6
125 18 1.1 0.6 41 500 46 000 4 250 4 700 16.6 7 500 10 000 23.4 97 118 1 0.563 7918 C DB DF DT 67 500 92 000 6 900 9 400 6 000 8 500 46.8 10.8 120 0.6
140 24 1.5 1 67 500 66 500 6 850 6 750 4 800 6 700 45.2 99 131 1.5 1.19 7018 A DB DF DT 109 000 133 000 11 200 13 500 3 800 5 300 90.4 42.4 96 134 1
140 24 1.5 1 71 500 69 000 7 300 7 050 15.7 7 100 9 500 27.4 99 131 1.5 1.34 7018 C DB DF DT 116 000 138 000 11 900 14 100 5 600 8 000 54.8 6.8 134 1
160 30 2 1 118 000 103 000 12 000 10 500 4 500 6 000 51.1 100 150 2 2.25 7218 A DB DF DT 191 000 206 000 19 500 21 000 3 600 5 000 102.2 42.2 96 154 1
160 30 2 1 107 000 94 000 10 900 9 550 3 200 4 300 67.4 100 150 2 2.29 7218 B DB DF DT 173 000 188 000 17 700 19 100 2 600 3 400 134.9 74.9 96 154 1
160 30 2 1 123 000 105 000 12 500 10 700 14.6 6 300 9 000 31.7 100 150 2 2.51 7218 C DB DF DT 199 000 209 000 20 300 21 400 5 300 7 100 63.5 3.5 154 1
190 43 3 1.1 171 000 147 000 17 400 15 000 3 200 4 300 61.9 104 176 2.5 5.06 7318 A DB DF DT 277 000 294 000 28 300 30 000 2 600 3 400 123.8 37.8 97 183 1
190 43 3 1.1 156 000 135 000 15 900 13 800 2 800 3 800 80.2 104 176 2.5 5.17 7318 B DB DF DT 254 000 270 000 25 900 27 600 2 200 3 000 160.5 74.5 97 183 1
95 130 18 1.1 0.6 40 000 45 500 4 050 4 650 6 000 8 500 35.2 102 123 1 0.597 7919 A5 DB DF DT 64 500 91 000 6 600 9 250 4 800 6 700 70.5 34.5 125 0.6
130 18 1.1 0.6 42 500 48 000 4 300 4 900 16.7 7 100 10 000 24.1 102 123 1 0.591 7919 C DB DF DT 68 500 96 000 7 000 9 800 5 600 8 000 48.1 12.1 125 0.6
145 24 1.5 1 67 000 67 000 6 800 6 800 4 500 6 300 46.6 104 136 1.5 1.43 7019 A DB DF DT 109 000 134 000 11 100 13 600 3 800 5 000 93.3 45.3 139 1
145 24 1.5 1 73 500 73 000 7 500 7 450 15.9 6 700 9 000 28.1 104 136 1.5 1.42 7019 C DB DF DT 119 000 146 000 12 200 14 900 5 300 7 500 56.1 8.1 139 1
170 32 2.1 1.1 128 000 111 000 13 000 11 300 4 300 5 600 54.2 107 158 2 2.68 7219 A DB DF DT 208 000 221 000 21 200 22 600 3 400 4 500 108.5 44.5 102 163 1
170 32 2.1 1.1 116 000 101 000 11 800 10 300 3 000 4 000 71.6 107 158 2 2.74 7219 B DB DF DT 188 000 202 000 19 200 20 500 2 400 3 200 143.2 79.2 102 163 1
170 32 2.1 1.1 133 000 112 000 13 500 11 400 14.6 6 000 8 500 33.7 107 158 2 3.05 7219 C DB DF DT 216 000 224 000 22 000 22 800 4 800 6 700 67.5 3.5 163 1
200 45 3 1.1 183 000 162 000 18 600 16 600 3 000 4 000 65.1 109 186 2.5 5.83 7319 A DB DF DT 297 000 325 000 30 500 33 000 2 400 3 200 130.2 40.2 102 193 1
200 45 3 1.1 167 000 149 000 17 100 15 200 2 600 3 600 84.3 109 186 2.5 5.98 7319 B DB DF DT 272 000 298 000 27 700 30 500 2 200 3 000 168.7 78.7 102 193 1
100 140 20 1.1 0.6 47 500 51 500 4 850 5 250 5 600 8 000 38.0 107 133 1 0.804 7920 A5 DB DF DT 77 000 103 000 7 850 10 500 4 500 6 300 76.0 36.0 135 0.6
140 20 1.1 0.6 50 000 54 000 5 100 5 550 16.5 6 700 9 000 26.1 107 133 1 0.794 7920 C DB DF DT 81 500 108 000 8 300 11 100 5 300 7 500 52.2 12.2 135 0.6
150 24 1.5 1 68 500 70 500 6 950 7 200 4 500 6 000 48.1 109 141 1.5 1.48 7020 A DB DF DT 111 000 141 000 11 300 14 400 3 600 5 000 96.2 48.2 144 1
(2) The suffixes A, A5, B, and C represent contact angles of 30, 25, 40, and 15 respectively.
B 62 B 63
B046-075E.indd 62-63 11/20/13 4:55:11 PM

Single, DT DB or DF
Angle Cor
r 0.178 0.38 1 0 0.44 1.47 1 1.65 0.72 2.39
r1 ra rb ra 0.357 0.40 1 0 0.44 1.40 1 1.57 0.72 2.28
0.714 0.43 1 0 0.44 1.30 1 1.46 0.72 2.11
1.07 0.46 1 0 0.44 1.23 1 1.38 0.72 2.00
15
r1 1.43 0.47 1 0 0.44 1.19 1 1.34 0.72 1.93
r ra ra rb 2.14 0.50 1 0 0.44 1.12 1 1.26 0.72 1.82
3.57 0.55 1 0 0.44 1.02 1 1.14 0.72 1.66
0.56 1 0 0.44 1.00 1 1.12 0.72 1.63
5.35
0.68 1 0 0.41 0.87 1 0.92 0.67 1.41
30 0.80 1 0 0.39 0.76 1 0.78 0.63 1.24
a0 a0 40 1.14 1 0 0.35 0.57 1 0.55 0.57 0.93

a 15 0.5 0.46 1 0.92 mounting
When
25 0.5 0.38 1 0.76 F r >0.5F r +Y 0 F a
DB DF DT 40 0.5 0.26 1 0.52
(min 1) (mm) (min 1) a0
100 150 24 1.5 1 75 500 77 000 7 700 7 900 16.0 6 300 9 000 28.7 109 141 1.5 1.46 7020 C DB DF DT 122 000 154 000 12 500 15 800 5 300 7 100 57.5 9.5 144 1
180 34 2.1 1.1 144 000 126 000 14 700 12 800 4 000 5 300 57.4 112 168 2 3.22 7220 A DB DF DT 233 000 251 000 23 800 25 600 3 200 4 300 114.8 46.8 107 173 1
180 34 2.1 1.1 130 000 114 000 13 300 11 700 2 800 3 800 75.7 112 168 2 3.28 7220 B DB DF DT 212 000 229 000 21 600 23 300 2 200 3 000 151.5 83.5 107 173 1
180 34 2.1 1.1 149 000 127 000 15 200 12 900 14.5 5 600 8 000 35.7 112 168 2 3.65 7220 C DB DF DT 242 000 254 000 24 700 25 900 4 500 6 300 71.5 3.5 173 1
215 47 3 1.1 207 000 193 000 21 100 19 700 2 800 3 800 69.0 114 201 2.5 7.29 7320 A DB DF DT 335 000 385 000 34 500 39 500 2 200 3 000 137.9 43.9 107 208 1
215 47 3 1.1 190 000 178 000 19 400 18 100 2 400 3 400 89.6 114 201 2.5 7.43 7320 B DB DF DT 310 000 355 000 31 500 36 000 2 000 2 800 179.2 85.2 107 208 1
105 145 20 1.1 0.6 48 000 54 000 4 900 5 500 5 600 7 500 39.2 112 138 1 0.82 7921 A5 DB DF DT 78 500 108 000 8 000 11 000 4 300 6 000 78.3 38.3 140 0.6
145 20 1.1 0.6 51 000 57 000 5 200 5 800 16.6 6 300 9 000 26.7 112 138 1 0.826 7921 C DB DF DT 83 000 114 000 8 450 11 600 5 300 7 100 53.5 13.5 140 0.6
160 26 2 1 80 000 81 500 8 150 8 350 4 300 5 600 51.2 115 150 2 1.84 7021 A DB DF DT 130 000 163 000 13 300 16 700 3 400 4 500 102.5 50.5 154 1
160 26 2 1 88 000 89 500 9 000 9 100 15.9 6 000 8 500 30.7 115 150 2 1.82 7021 C DB DF DT 143 000 179 000 14 600 18 200 4 800 6 700 61.5 9.5 154 1
190 36 2.1 1.1 157 000 142 000 16 000 14 400 3 800 5 000 60.6 117 178 2 3.84 7221 A DB DF DT 254 000 283 000 25 900 28 900 3 000 4 000 121.2 49.2 112 183 1
190 36 2.1 1.1 142 000 129 000 14 500 13 100 2 600 3 600 79.9 117 178 2 3.92 7221 B DB DF DT 231 000 258 000 23 500 26 300 2 200 3 000 159.8 87.8 112 183 1
190 36 2.1 1.1 162 000 143 000 16 600 14 600 14.5 5 300 7 500 37.7 117 178 2 4.33 7221 C DB DF DT 264 000 286 000 26 900 29 100 4 300 6 000 75.5 3.5 183 1
225 49 3 1.1 208 000 193 000 21 200 19 700 2 600 3 600 72.1 119 211 2.5 9.34 7321 A DB DF DT 335 000 385 000 34 500 39 500 2 200 2 800 144.3 46.3 218 1
225 49 3 1.1 191 000 177 000 19 400 18 100 2 400 3 200 93.7 119 211 2.5 9.43 7321 B DB DF DT 310 000 355 000 31 500 36 000 1 900 2 600 187.4 89.4 218 1
110 150 20 1.1 0.6 49 000 56 000 5 000 5 750 5 300 7 100 40.3 117 143 1 0.877 7922 A5 DB DF DT 79 500 112 000 8 100 11 500 4 300 5 600 80.6 40.6 145 0.6
150 20 1.1 0.6 52 000 59 500 5 300 6 050 16.7 6 300 8 500 27.4 117 143 1 0.867 7922 C DB DF DT 84 500 119 000 8 600 12 100 5 000 6 700 54.8 14.8 145 0.6
170 28 2 1 96 500 95 500 9 850 9 700 4 000 5 300 54.4 120 160 2 2.28 7022 A DB DF DT 157 000 191 000 16 000 19 400 3 200 4 300 108.8 52.8 164 1
170 28 2 1 106 000 104 000 10 800 10 600 15.6 5 600 8 000 32.7 120 160 2 2.26 7022 C DB DF DT 172 000 208 000 17 600 21 200 4 500 6 300 65.5 9.5 164 1
200 38 2.1 1.1 170 000 158 000 17 300 16 100 3 600 4 800 63.7 122 188 2 4.49 7222 A DB DF DT 276 000 315 000 28 100 32 500 2 800 4 000 127.5 51.5 117 193 1
200 38 2.1 1.1 154 000 144 000 15 700 14 700 2 600 3 400 84.0 122 188 2 4.58 7222 B DB DF DT 250 000 289 000 25 500 29 400 2 000 2 800 168.1 92.1 117 193 1
200 38 2.1 1.1 176 000 160 000 17 900 16 300 14.5 5 000 7 100 39.8 122 188 2 5.1 7222 C DB DF DT 286 000 320 000 29 200 32 500 4 000 5 600 79.5 3.5 193 1
240 50 3 1.1 220 000 215 000 22 500 21 900 2 600 3 400 75.5 124 226 2.5 11.1 7322 A DB DF DT 360 000 430 000 36 500 44 000 2 000 2 600 151.0 51.0 233 1
240 50 3 1.1 201 000 197 000 20 500 20 100 2 200 3 000 98.4 124 226 2.5 11.2 7322 B DB DF DT 325 000 395 000 33 500 40 000 1 800 2 400 196.8 96.8 233 1
120 165 22 1.1 0.6 67 500 77 000 6 900 7 850 4 800 6 300 44.2 127 158 1 1.15 7924 A5 DB DF DT 110 000 154 000 11 200 15 700 3 800 5 300 88.5 44.5 160 0.6
165 22 1.1 0.6 72 000 81 000 7 300 8 300 16.5 5 600 7 500 30.1 127 158 1 1.15 7924 C DB DF DT 117 000 162 000 11 900 16 600 4 500 6 300 60.2 16.2 160 0.6
180 28 2 1 102 000 107 000 10 400 10 900 3 600 5 000 57.3 130 170 2 2.45 7024 A DB DF DT 166 000 213 000 16 900 21 700 3 000 4 000 114.6 58.6 174 1
215 40 2.1 1.1 183 000 177 000 18 600 18 100 3 200 4 500 68.3 132 203 2 6.22 7224 A DB DF DT 297 000 355 000 30 500 36 000 2 600 3 600 136.7 56.7 208 1
215 40 2.1 1.1 165 000 162 000 16 900 16 500 2 400 3 200 90.3 132 203 2 6.26 7224 B DB DF DT 269 000 325 000 27 400 33 000 1 900 2 600 180.5 100.5 208 1
260 55 3 1.1 246 000 252 000 25 100 25 700 2 200 3 000 82.3 134 246 2.5 14.5 7324 A DB DF DT 400 000 505 000 41 000 51 500 1 800 2 400 164.7 54.7 253 1
260 55 3 1.1 225 000 231 000 23 000 23 600 2 000 2 800 107.2 134 246 2.5 14.4 7324 B DB DF DT 365 000 460 000 37 500 47 000 1 600 2 200 214.4 104.4 253 1
B 64 B 65
B046-075E.indd 64-65 11/20/13 4:55:13 PM

Single, DT DB or DF
Angle Cor
B 2B 2B X Y X Y X Y X Y
2B
0.178 0.38 1 0 0.44 1.47 1 1.65 0.72 2.39
r r1 ra rb ra 0.357 0.40 1 0 0.44 1.40 1 1.57 0.72 2.28
0.714 0.43 1 0 0.44 1.30 1 1.46 0.72 2.11
1.07 0.46 1 0 0.44 1.23 1 1.38 0.72 2.00
15
r 1.43 0.47 1 0 0.44 1.19 1 1.34 0.72 1.93
r ra ra ra 2.14 0.50 1 0 0.44 1.12 1 1.26 0.72 1.82
3.57 0.55 1 0 0.44 1.02 1 1.14 0.72 1.66
5.35 0.56 1 0 0.44 1.00 1 1.12 0.72 1.63
jD jd jDa jda jDb jd a jDa jd b 25
30

0.68
0.80
1
1
0
0
0.41 0.87
0.39 0.76
1
1
0.92 0.67 1.41
0.78 0.63 1.24
a0 a0 40 1.14 1 0 0.35 0.57 1 0.55 0.57 0.93

a 15 0.5 0.46 1 0.92 mounting
When
25 0.5 0.38 1 0.76 F r >0.5F r +Y 0 F a
DB DF DT 40 0.5 0.26 1 0.52
(min 1) (mm) (min 1) a0
130 180 24 1.5 1 74 000 86 000 7 550 8 750 4 300 6 000 48.1 139 171 1.5 1.54 7926 A5 DB DF DT 120 000 172 000 12 300 17 500 3 400 4 800 96.3 48.3 174 1
180 24 1.5 1 78 500 91 000 8 000 9 250 16.5 5 000 7 100 32.8 139 171 1.5 1.5 7926 C DB DF DT 128 000 182 000 13 000 18 500 4 000 5 600 65.5 17.5 174 1
200 33 2 1 117 000 125 000 12 000 12 800 3 400 4 500 64.1 140 190 2 3.68 7026 A DB DF DT 191 000 251 000 19 400 25 600 2 600 3 600 128.3 62.3 194 1
230 40 3 1.1 189 000 193 000 19 300 19 600 2 400 3 200 72.0 144 216 2.5 7.06 7226 A DB DF DT 310 000 385 000 31 500 39 500 1 900 2 600 143.9 63.9 223 1
230 40 3 1.1 171 000 175 000 17 400 17 800 2 200 3 000 95.5 144 216 2.5 7.1 7226 B DB DF DT 278 000 350 000 28 300 35 500 1 700 2 400 191.0 111.0 223 1
280 58 4 1.5 273 000 293 000 27 900 29 800 2 200 2 800 88.2 148 262 3 17.5 7326 A DB DF DT 445 000 585 000 45 500 59 500 1 700 2 200 176.3 60.3 271 1.5
280 58 4 1.5 250 000 268 000 25 500 27 400 1 900 2 600 115.0 148 262 3 17.6 7326 B DB DF DT 405 000 535 000 41 500 54 500 1 500 2 000 230.0 114.0 271 1.5
140 190 24 1.5 1 75 000 90 000 7 650 9 200 4 000 5 600 50.5 149 181 1.5 1.63 7928 A5 DB DF DT 122 000 180 000 12 400 18 400 3 200 4 500 100.9 52.9 184 1
190 24 1.5 1 79 500 95 500 8 100 9 700 16.7 4 800 6 700 34.1 149 181 1.5 1.63 7928 C DB DF DT 129 000 191 000 13 200 19 400 3 800 5 300 68.2 20.2 184 1
210 33 2 1 120 000 133 000 12 200 13 500 3 200 4 300 67.0 150 200 2 3.9 7028 A DB DF DT 194 000 265 000 19 800 27 000 2 600 3 400 134.0 68.0 204 1
250 42 3 1.1 218 000 234 000 22 300 23 900 2 200 3 000 77.3 154 236 2.5 8.92 7228 A DB DF DT 355 000 470 000 36 000 48 000 1 800 2 400 154.6 70.6 243 1
250 42 3 1.1 197 000 213 000 20 100 21 700 2 000 2 800 102.8 154 236 2.5 8.94 7228 B DB DF DT 320 000 425 000 32 500 43 500 1 600 2 200 205.6 121.6 243 1
300 62 4 1.5 300 000 335 000 30 500 34 500 2 000 2 600 94.5 158 282 3 21.4 7328 A DB DF DT 490 000 670 000 50 000 68 500 1 600 2 000 189.0 65.0 291 1.5
300 62 4 1.5 275 000 310 000 28 100 31 500 1 700 2 400 123.3 158 282 3 21.6 7328 B DB DF DT 445 000 615 000 45 500 63 000 1 400 1 900 246.6 122.6 291 1.5
150 210 28 2 1 96 500 115 000 9 850 11 800 3 800 5 000 56.0 160 200 2 2.97 7930 A5 DB DF DT 157 000 231 000 16 000 23 500 3 000 4 000 112.0 56.0 204 1
210 28 2 1 102 000 122 000 10 400 12 400 16.6 4 300 6 000 38.1 160 200 2 2.96 7930 C DB DF DT 166 000 244 000 16 900 24 900 3 600 4 800 76.2 20.2 204 1
225 35 2.1 1.1 137 000 154 000 14 000 15 700 2 400 3 000 71.6 162 213 2 4.75 7030 A DB DF DT 222 000 305 000 22 700 31 500 1 900 2 400 143.3 73.3 218 1
270 45 3 1.1 248 000 280 000 25 300 28 500 2 000 2 800 83.1 164 256 2.5 11.2 7230 A DB DF DT 405 000 560 000 41 000 57 000 1 600 2 200 166.3 76.3 263 1
270 45 3 1.1 225 000 254 000 22 900 25 900 1 800 2 600 110.6 164 256 2.5 11.2 7230 B DB DF DT 365 000 510 000 37 000 52 000 1 500 2 000 221.2 131.2 263 1
320 65 4 1.5 315 000 370 000 32 500 38 000 1 800 2 400 100.3 168 302 3 26 7330 A DB DF DT 515 000 745 000 52 500 75 500 1 500 1 900 200.7 70.7 311 1.5
320 65 4 1.5 289 000 340 000 29 400 34 500 1 600 2 200 131.1 168 302 3 25.9 7330 B DB DF DT 470 000 680 000 48 000 69 500 1 300 1 800 262.2 132.2 311 1.5
160 220 28 2 1 106 000 133 000 10 800 13 500 16.7 3 800 5 000 39.4 170 210 2 3.1 7932 C DB DF DT 173 000 265 000 17 600 27 000 3 000 4 000 78.9 22.9 214 1
240 38 2.1 1.1 155 000 176 000 15 800 18 000 2 200 2 800 76.7 172 228 2 5.77 7032 A DB DF DT 252 000 355 000 25 700 36 000 1 700 2 400 153.5 77.5 233 1
290 48 3 1.1 263 000 305 000 26 800 31 500 1 900 2 600 89.0 174 276 2.5 14.1 7232 A DB DF DT 425 000 615 000 43 500 62 500 1 500 2 000 177.9 81.9 283 1
290 48 3 1.1 238 000 279 000 24 200 28 400 1 700 2 400 118.4 174 276 2.5 14.2 7232 B DB DF DT 385 000 555 000 39 500 57 000 1 400 1 900 236.8 140.8 283 1
340 68 4 1.5 345 000 420 000 35 500 43 000 1 700 2 200 106.2 178 322 3 30.7 7332 A DB DF DT 565 000 845 000 57 500 86 000 1 400 1 800 212.3 76.3 331 1.5
340 68 4 1.5 315 000 385 000 32 000 39 500 1 500 2 000 138.9 178 322 3 30.8 7332 B DB DF DT 515 000 770 000 52 500 78 500 1 200 1 700 277.8 141.8 331 1.5
170 230 28 2 1 113 000 148 000 11 500 15 100 16.8 3 600 4 800 40.8 180 220 2 3.36 7934 C DB DF DT 183 000 297 000 18 700 30 000 2 800 3 800 81.6 25.6 224 1
260 42 2.1 1.1 186 000 214 000 19 000 21 900 2 000 2 600 83.1 182 248 2 7.9 7034 A DB DF DT 300 000 430 000 31 000 43 500 1 600 2 200 166.1 82.1 253 1
310 52 4 1.5 295 000 360 000 30 000 36 500 1 800 2 400 95.3 188 292 3 17.3 7234 A DB DF DT 480 000 715 000 49 000 73 000 1 400 1 900 190.6 86.6 301 1.5
310 52 4 1.5 266 000 325 000 27 200 33 000 1 600 2 200 126.7 188 292 3 17.6 7234 B DB DF DT 435 000 650 000 44 000 66 500 1 300 1 700 253.4 149.4 301 1.5
360 72 4 1.5 390 000 485 000 39 500 49 500 1 600 2 200 112.5 188 342 3 35.8 7334 A DB DF DT 630 000 970 000 64 500 99 000 1 300 1 700 225.0 81.0 351 1.5
360 72 4 1.5 355 000 445 000 36 000 45 500 1 400 2 000 147.2 188 342 3 35.6 7334 B DB DF DT 575 000 890 000 59 000 90 500 1 100 1 600 294.3 150.3 351 1.5
B 66 B 67
B046-075E.indd 66-67 11/20/13 4:55:14 PM

Single, DT DB or DF
Angle Cor
B 2B 2B X Y X Y X Y X Y
2B
0.178 0.38 1 0 0.44 1.47 1 1.65 0.72 2.39
r r1 ra rb ra 0.357 0.40 1 0 0.44 1.40 1 1.57 0.72 2.28
0.714 0.43 1 0 0.44 1.30 1 1.46 0.72 2.11
1.07 0.46 1 0 0.44 1.23 1 1.38 0.72 2.00
15
r 1.43 0.47 1 0 0.44 1.19 1 1.34 0.72 1.93
r ra ra ra 2.14 0.50 1 0 0.44 1.12 1 1.26 0.72 1.82
3.57 0.55 1 0 0.44 1.02 1 1.14 0.72 1.66
5.35 0.56 1 0 0.44 1.00 1 1.12 0.72 1.63
jD jd jDa jda jDb jd a jDa jd b 25
30

0.68
0.80
1
1
0
0
0.41 0.87
0.39 0.76
1
1
0.92 0.67 1.41
0.78 0.63 1.24
a0 a0 40 1.14 1 0 0.35 0.57 1 0.55 0.57 0.93

a 15 0.5 0.46 1 0.92 mounting
When
25 0.5 0.38 1 0.76 F r >0.5F r +Y 0 F a
DB DF DT 40 0.5 0.26 1 0.52
(min 1) (mm) (min 1) a0
180 250 33 2 1 145 000 184 000 14 800 18 800 16.6 3 200 4 500 45.3 190 240 2 4.9 7936 C DB DF DT 236 000 370 000 24 000 37 500 2 600 3 600 90.6 24.6 244 1
280 46 2.1 1.1 207 000 252 000 21 100 25 700 1 900 2 400 89.4 192 268 2 10.5 7036 A DB DF DT 335 000 505 000 34 500 51 500 1 500 2 000 178.8 86.8 273 1
320 52 4 1.5 305 000 385 000 31 000 39 000 1 700 2 200 98.2 198 302 3 18.1 7236 A DB DF DT 495 000 770 000 50 500 78 500 1 400 1 800 196.3 92.3 311 1.5
320 52 4 1.5 276 000 350 000 28 100 35 500 1 500 2 000 130.9 198 302 3 18.4 7236 B DB DF DT 450 000 700 000 45 500 71 000 1 200 1 700 261.8 157.8 311 1.5
380 75 4 1.5 410 000 535 000 41 500 54 500 1 500 2 000 118.3 198 362 3 42.1 7336 A DB DF DT 665 000 1 070 000 68 000 109 000 1 200 1 600 236.6 86.6 371 1.5
380 75 4 1.5 375 000 490 000 38 000 50 000 1 300 1 800 155.0 198 362 3 42.6 7336 B DB DF DT 605 000 975 000 62 000 99 500 1 100 1 500 309.9 159.9 371 1.5
190 260 33 2 1 147 000 192 000 15 000 19 600 16.7 3 000 4 300 46.6 200 250 2 4.98 7938 C DB DF DT 239 000 385 000 24 400 39 000 2 400 3 400 93.3 27.3 254 1
290 46 2.1 1.1 224 000 280 000 22 800 28 600 1 800 2 400 92.3 202 278 2 11.3 7038 A DB DF DT 365 000 560 000 37 000 57 000 1 400 1 900 184.6 92.6 283 1
340 55 4 1.5 315 000 410 000 32 000 42 000 1 600 2 200 104.0 208 322 3 22.4 7238 A DB DF DT 510 000 825 000 52 000 84 000 1 300 1 700 208.0 98.0 331 1.5
340 55 4 1.5 284 000 375 000 28 900 38 000 1 400 2 000 138.7 208 322 3 22.5 7238 B DB DF DT 460 000 750 000 47 000 76 000 1 100 1 600 277.3 167.3 331 1.5
400 78 5 2 450 000 600 000 46 000 61 000 1 400 1 900 124.2 212 378 4 47.5 7338 A DB DF DT 730 000 1 200 000 74 500 122 000 1 100 1 500 248.3 92.3 390 2
400 78 5 2 410 000 550 000 42 000 56 000 1 300 1 700 162.8 212 378 4 47.2 7338 B DB DF DT 670 000 1 100 000 68 000 112 000 1 000 1 400 325.5 169.5 390 2
200 280 38 2.1 1.1 189 000 244 000 19 300 24 900 16.5 2 800 4 000 51.2 212 268 2 6.85 7940 C DB DF DT 305 000 490 000 31 500 50 000 2 200 3 200 102.3 26.3 273 1
310 51 2.1 1.1 240 000 310 000 24 500 31 500 1 700 2 200 99.1 212 298 2 13.7 7040 A DB DF DT 390 000 620 000 40 000 63 500 1 300 1 800 198.2 96.2 303 1
360 58 4 1.5 335 000 450 000 34 500 46 000 1 500 2 000 109.8 218 342 3 26.5 7240 A DB DF DT 550 000 900 000 56 000 92 000 1 200 1 600 219.6 103.6 351 1.5
360 58 4 1.5 305 000 410 000 31 000 41 500 1 300 1 800 146.5 218 342 3 26.6 7240 B DB DF DT 495 000 815 000 50 500 83 000 1 100 1 500 292.9 176.9 351 1.5
420 80 5 2 475 000 660 000 48 500 67 000 1 300 1 800 129.5 222 398 4 54.4 7340 A DB DF DT 770 000 1 320 000 78 500 134 000 1 100 1 400 259.0 99.0 410 2
420 80 5 2 430 000 600 000 44 000 61 500 1 200 1 600 170.1 222 398 4 55.3 7340 B DB DF DT 700 000 1 200 000 71 500 123 000 950 1 300 340.1 180.1 410 2
B 68 B 69
B046-075E.indd 68-69 11/20/13 4:55:16 PM

DOUBLE-ROW ANGULAR CONTACT BALL BEARINGS
B
r ra
P = X Fr +Y Fa
r ra
Fa/ Fre Fa/ Fr>e
e
jD jd jDa jd a
X Y X Y
1 0.92 0.67 1.41 0.68
a0
P0 = Fr +0 . 7 6 Fa
Boundary Dimensions Basic Load Ratings Limiting Speeds Load Center Abutment and Fillet Mass
(mm) (N) {kgf} (min 1) Spacings Dimensions (mm) (kg)
Bearing
(mm)
Numbers
d D B r Cr C 0r Cr C 0r Grease Oil a0 da Da ra
10 30 14.3 0.6 7 150 3 900 730 400 17 000 22 000 5200 14.5 15 25 0.6 0.050
12 32 15.9 0.6 10 500 5 800 1 070 590 15 000 20 000 5201 16.7 17 27 0.6 0.060
15 35 15.9 0.6 11 700 7 050 1 190 715 13 000 17 000 5202 18.3 20 30 0.6 0.070
42 19 1 17 600 10 200 1 800 1 040 11 000 15 000 5302 22.0 21 36 1 0.11
17 40 17.5 0.6 14 600 9 050 1 490 920 11 000 15 000 5203 20.8 22 35 0.6 0.090
47 22.2 1 21 000 12 600 2 140 1 280 10 000 13 000 5303 25.0 23 41 1 0.14
20 47 20.6 1 19 600 12 400 2 000 1 270 10 000 13 000 5204 24.3 26 41 1 0.12
52 22.2 1.1 24 600 15 000 2 510 1 530 9 000 12 000 5304 26.7 27 45 1 0.23
25 52 20.6 1 21 300 14 700 2 170 1 500 8 500 11 000 5205 26.8 31 46 1 0.19
62 25.4 1.1 32 500 20 700 3 350 2 110 7 500 10 000 5305 31.8 32 55 1 0.34
30 62 23.8 1 29 600 21 100 3 000 2 150 7 100 9 500 5206 31.6 36 56 1 0.29
72 30.2 1.1 40 500 28 100 4 150 2 870 6 300 8 500 5306 36.5 37 65 1 0.51
35 72 27 1.1 39 000 28 700 4 000 2 920 6 300 8 000 5207 36.6 42 65 1 0.43
80 34.9 1.5 51 000 36 000 5 200 3 700 5 600 7 500 5307 41.6 44 71 1.5 0.79
40 80 30.2 1.1 44 000 33 500 4 500 3 400 5 600 7 100 5208 41.5 47 73 1 0.57
90 36.5 1.5 56 500 41 000 5 800 4 200 5 300 6 700 5308 45.5 49 81 1.5 1.05
45 85 30.2 1.1 49 500 38 000 5 050 3 900 5 000 6 700 5209 43.4 52 78 1 0.62
100 39.7 1.5 68 500 51 000 7 000 5 200 4 500 6 000 5309 50.6 54 91 1.5 1.4
50 90 30.2 1.1 53 000 43 500 5 400 4 400 4 800 6 000 5210 45.9 57 83 1 0.67
110 44.4 2 81 500 61 500 8 300 6 250 4 300 5 600 5310 55.6 60 100 2 1.95
55 100 33.3 1.5 56 000 49 000 5 700 5 000 4 300 5 600 5211 50.1 64 91 1.5 0.96
120 49.2 2 95 000 73 000 9 700 7 450 3 800 5 000 5311 60.6 65 110 2 2.3
60 110 36.5 1.5 69 000 62 000 7 050 6 300 3 800 5 000 5212 56.5 69 101 1.5 1.35
130 54 2.1 125 000 98 500 12 800 10 000 3 400 4 500 5312 69.2 72 118 2 3.15
65 120 38.1 1.5 76 500 69 000 7 800 7 050 3 600 4 500 5213 59.7 74 111 1.5 1.65
140 58.7 2.1 142 000 113 000 14 500 11 500 3 200 4 300 5313 72.8 77 128 2 3.85
70 125 39.7 1.5 94 000 82 000 9 600 8 400 3 400 4 500 5214 63.8 79 116 1.5 1.8
150 63.5 2.1 159 000 128 000 16 200 13 100 3 000 3 800 5314 78.3 82 138 2 4.9
75 130 41.3 1.5 93 500 83 000 9 550 8 500 3 200 4 300 5215 66.1 84 121 1.5 1.9
80 140 44.4 2 99 000 93 000 10 100 9 500 3 000 3 800 5216 69.6 90 130 2 2.5
85 150 49.2 2 116 000 110 000 11 800 11 200 2 800 3 600 5217 75.3 95 140 2 3.4
B 70 B 71
B046-075E.indd 70-71 11/20/13 4:55:17 PM

B
ra
r
r ra
jD jd jDa jd a Pa =Fa

P0a = Fa
a0
Bearing
(mm)
Numbers
d D B r Ca C 0a Ca C 0a Grease Oil a0 da Da ra
30 62 16 1 31 000 45 000 3 150 4 600 8 500 12 000 QJ 206 32.2 36 56 1 0.24

72 19 1.1 46 000 63 000 4 700 6 450 8 000 11 000 QJ 306 35.7 37 65 1 0.42
35 72 17 1.1 41 000 61 500 4 200 6 250 7 500 10 000 QJ 207 37.5 42 65 1 0.35
80 21 1.5 55 000 80 000 5 600 8 150 7 100 9 500 QJ 307 40.3 44 71 1.5 0.57
40 80 18 1.1 49 000 77 500 5 000 7 900 6 700 9 000 QJ 208 42.0 47 73 1 0.45
90 23 1.5 67 000 100 000 6 850 10 200 6 300 8 500 QJ 308 45.5 49 81 1.5 0.78
45 85 19 1.1 55 000 88 500 5 600 9 000 6 300 8 500 QJ 209 45.5 52 78 1 0.52
100 25 1.5 87 500 133 000 8 900 13 500 5 600 7 500 QJ 309 50.8 54 91 1.5 1.05
50 90 20 1.1 57 000 97 000 5 850 9 900 5 600 8 000 QJ 210 49.0 57 83 1 0.59
110 27 2 102 000 159 000 10 400 16 200 5 000 6 700 QJ 310 56.0 60 100 2 1.35
55 100 21 1.5 71 000 122 000 7 200 12 500 5 300 7 100 QJ 211 54.3 64 91 1.5 0.77
120 29 2 118 000 187 000 12 000 19 100 4 500 6 300 QJ 311 61.3 65 110 2 1.75
60 110 22 1.5 85 500 150 000 8 750 15 300 4 800 6 300 QJ 212 59.5 69 101 1.5 0.98
130 31 2.1 135 000 217 000 13 800 22 200 4 300 5 600 QJ 312 66.5 72 118 2 2.15
65 120 23 1.5 97 500 179 000 9 950 18 300 4 300 6 000 QJ 213 64.8 74 111 1.5 1.2
140 33 2.1 153 000 250 000 15 600 25 500 3 800 5 300 QJ 313 71.8 77 128 2 2.7
70 125 24 1.5 106 000 197 000 10 800 20 100 4 000 5 600 QJ 214 68.3 79 116 1.5 1.3
150 35 2.1 172 000 285 000 17 500 29 100 3 600 5 000 QJ 314 77.0 82 138 2 3.18
75 130 25 1.5 110 000 212 000 11 200 21 700 3 800 5 300 QJ 215 71.8 84 121 1.5 1.5
160 37 2.1 187 000 320 000 19 100 33 000 3 400 4 800 QJ 315 82.3 87 148 2 3.9
80 125 22 1.1 77 000 167 000 7 850 17 000 3 800 5 300 QJ 1016 71.8 87 118 1 1.05
140 26 2 124 000 236 000 12 600 24 100 3 600 5 000 QJ 216 77.0 90 130 2 1.85
170 39 2.1 202 000 360 000 20 600 37 000 3 200 4 300 QJ 316 87.5 92 158 2 4.6
85 130 22 1.1 79 000 176 000 8 050 18 000 3 800 5 000 QJ 1017 75.3 92 123 1 1.1
150 28 2 143 000 276 000 14 600 28 200 3 400 4 800 QJ 217 82.3 95 140 2 2.2
180 41 3 218 000 405 000 22 300 41 000 3 000 4 000 QJ 317 92.8 99 166 2.5 5.34
90 140 24 1.5 94 000 208 000 9 600 21 200 3 400 4 800 QJ 1018 80.5 99 131 1.5 1.45
160 30 2 164 000 320 000 16 700 32 500 3 200 4 300 QJ 218 87.5 100 150 2 2.75
190 43 3 235 000 450 000 23 900 45 500 2 800 3 800 QJ 318 98.0 104 176 2.5 6.4
95 145 24 1.5 96 500 220 000 9 800 22 500 3 400 4 500 QJ 1019 84.0 104 136 1.5 1.5
170 32 2.1 177 000 340 000 18 000 35 000 3 000 4 000 QJ 219 92.8 107 158 2 3.35
200 45 3 251 000 495 000 25 600 50 500 2 600 3 600 QJ 319 103.3 109 186 2.5 7.4
Remarks When using four-point contact ball bearings, please contact NSK.
B 72 B 73
B046-075E.indd 72-73 11/20/13 4:55:18 PM

B
ra
r
r ra
jD jd jDa jd a Pa =Fa

P0a = Fa
a0
Bearing
(mm)
Numbers
d D B r Ca C 0a Ca C 0a Grease Oil a0 da Da ra
100 150 24 1.5 98 500 232 000 10 000 23 700 3 200 4 300 QJ 1020 87.5 109 141 1.5 1.6
180 34 2.1 199 000 390 000 20 300 39 500 2 800 3 800 QJ 220 98.0 112 168 2 4.0
215 47 3 300 000 640 000 31 000 65 500 2 400 3 400 QJ 320 110.3 114 201 2.5 9.3
105 160 26 2 115 000 269 000 11 800 27 400 3 000 4 000 QJ 1021 92.8 115 150 2 2.0
190 36 2.1 217 000 435 000 22 100 44 500 2 600 3 600 QJ 221 103.3 117 178 2 4.7
225 49 3 305 000 640 000 31 000 65 500 2 400 3 200 QJ 321 115.5 119 211 2.5 10.5
110 170 28 2 139 000 315 000 14 200 32 000 2 800 3 800 QJ 1022 98.0 120 160 2 2.5
200 38 2.1 235 000 490 000 24 000 50 000 2 600 3 400 QJ 222 108.5 122 188 2 5.6
240 50 3 320 000 710 000 32 500 72 500 2 200 3 000 QJ 322 122.5 124 226 2.5 12.5
120 180 28 2 147 000 350 000 15 000 36 000 2 600 3 600 QJ 1024 105.0 130 170 2 2.65
215 40 2.1 265 000 585 000 27 000 60 000 2 400 3 200 QJ 224 117.3 132 203 2 6.9
260 55 3 360 000 835 000 36 500 85 500 2 000 2 800 QJ 324 133.0 134 246 2.5 15.4
130 200 33 2 169 000 415 000 17 300 42 000 2 400 3 200 QJ 1026 115.5 140 190 2 4.0
230 40 3 274 000 635 000 28 000 65 000 2 200 3 000 QJ 226 126.0 144 216 2.5 7.7
280 58 4 400 000 970 000 40 500 99 000 1 900 2 600 QJ 326 143.5 148 262 3 19
140 210 33 2 172 000 435 000 17 600 44 500 2 200 3 000 QJ 1028 122.5 150 200 2 4.3
250 42 3 239 000 710 000 29 900 72 500 2 000 2 800 QJ 228 136.5 154 236 2.5 9.8
300 62 4 440 000 1 110 000 44 500 114 000 1 700 2 400 QJ 328 154.0 158 282 3 24
150 225 35 2.1 197 000 505 000 20 100 51 500 2 000 2 800 QJ 1030 131.3 162 213 2 5.2
270 45 3 315 000 785 000 32 000 80 000 1 800 2 600 QJ 230 147.0 164 256 2.5 12
320 65 4 460 000 1 230 000 47 000 125 000 1 600 2 200 QJ 330 164.5 168 302 3 29
160 240 38 2.1 224 000 580 000 22 800 59 000 1 900 2 600 QJ 1032 140.0 172 228 2 6.4
290 48 3 380 000 1 010 000 39 000 103 000 1 700 2 400 QJ 232 157.5 174 276 2.5 15
340 68 4 505 000 1 400 000 51 500 143 000 1 500 2 000 QJ 332 175.1 178 322 3 31
170 260 42 2.1 268 000 705 000 27 300 72 000 1 800 2 400 QJ 1034 150.5 182 248 2 8.6
310 52 4 425 000 1 180 000 43 500 121 000 1 600 2 200 QJ 234 168.0 188 292 3 19.5
360 72 4 565 000 1 610 000 57 500 164 000 1 400 2 000 QJ 334 185.6 188 342 3 41
180 280 46 2.1 299 000 830 000 30 500 84 500 1 700 2 200 QJ 1036 161.0 192 268 2 11
320 52 4 440 000 1 270 000 45 000 130 000 1 500 2 000 QJ 236 175.1 198 302 3 20.5
380 75 4 595 000 1 770 000 60 500 180 000 1 300 1 800 QJ 336 196.1 198 362 3 48
190 290 46 2.1 325 000 925 000 33 000 94 000 1 600 2 200 QJ 1038 168.0 202 278 2 11.5
340 55 4 440 000 1 290 000 44 500 131 000 1 400 2 000 QJ 238 185.6 208 322 3 23
400 78 5 655 000 1 980 000 67 000 202 000 1 300 1 700 QJ 338 206.6 212 378 4 54.5
200 310 51 2.1 345 000 1 020 000 35 500 104 000 1 500 2 000 QJ 1040 178.6 212 298 2 15
360 58 4 490 000 1 480 000 49 500 151 000 1 300 1 800 QJ 240 196.1 218 342 3 27
420 80 5 690 000 2 180 000 70 500 222 000 1 200 1 600 QJ 340 217.1 222 398 4 61.5
Remarks When using four-point contact ball bearings, please contact NSK.
B 74 B 75
B046-075E.indd 74-75 11/20/13 4:55:19 PM

SELF-ALIGNING BALL BEARINGS
SELF-ALIGNING BALL BEARINGS Bore Diameter 5 110 mm B78

The outer ring has a spherical raceway and its center of curvature
coincides with that of the bearing; therefore, the axis of the inner ring, balls
and cage can deflect to some extent around the bearing center. This type is
recommended when the alignment of the shaft and housing is difficult and
when the shaft may bend. Since the contact angle is small, the axial load
capacity is low.
Pressed steel cages are usually used.
PROTRUSION AMOUNT OF BALLS

Among self-aligning ball bearings, there are some in which the balls
protrude from the side face as shown below. This protrusion amount b1 is
listed in the following table.
Bearing No. b1 (mm)

b1
2222(K), 2316(K) 0.5
2319(K), 2320(K) 0.5
2321 , 2322(K)
1318(K) 1.5
1319(K) 2
1320(K), 1321 3
1322(K)
TOLERANCES AND RUNNING

ACCURACY Table 8.2 (Pages A60 to A63)
RECOMMENDED FITS Table 9.2 (Page A84)

INTERNAL CLEARANCE Table 9.12 (Page A90)
PERMISSIBLE MISALIGNMENT
The permissible misalignment of self-aligning ball bearings is
approximately 0.07 to 0.12 radian (4 to 7) under normal loads. However,
depending on the surrounding structure, such an angle may not be possible.
Use care in the structural design.
B 76 B 77
B076-083E.indd 76-77 11/20/13 4:55:41 PM

B B
r r ra
r
ra
jD jd jD P = X Fr +Y Fa
jd
jD a jda
Fa/ Fre Fa/ Fr>e
X Y X Y
1 Y3 0.65 Y2
P0 =Fr +Y0 Fa
Cylindrical Bore Tapered Bore
The values of e, Y2 , Y3 , and Y0
are listed in the table below.
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers Abutment and Fillet Dimensions Constant Axial Load Factors Mass
d D B r Cr C 0r Cr C 0r Grease Oil Cylindrical Tapered da Da ra e Y2 Y3 Y0

min. Bore Bore(1) min. max. max. approx.
5 19 6 0.3 2 530 475 258 49 30 000 36 000 135 7 17 0.3 0.34 2.9 1.9 1.9 0.009
6 19 6 0.3 2 530 475 258 49 30 000 36 000 126 8 17 0.3 0.34 2.9 1.9 1.9 0.008
7 22 7 0.3 2 750 600 280 61 26 000 32 000 127 9 20 0.3 0.31 3.1 2.0 2.1 0.013
8 22 7 0.3 2 750 600 280 61 26 000 32 000 108 10 20 0.3 0.31 3.1 2.0 2.1 0.016
9 26 8 0.6 4 150 895 425 91 26 000 30 000 129 13 22 0.6 0.32 3.1 2.0 2.1 0.021
10 30 9 0.6 5 550 1 190 570 121 22 000 28 000 1200 14 26 0.6 0.32 3.1 2.0 2.1 0.033
30 14 0.6 7 450 1 590 760 162 24 000 28 000 2200 14 26 0.6 0.64 1.5 0.98 1.0 0.042
35 11 0.6 7 350 1 620 750 165 20 000 24 000 1300 14 31 0.6 0.35 2.8 1.8 1.9 0.057
35 17 0.6 9 200 2 010 935 205 18 000 22 000 2300 14 31 0.6 0.71 1.4 0.89 0.93 0.077
12 32 10 0.6 5 700 1 270 580 130 22 000 26 000 1201 16 28 0.6 0.36 2.7 1.8 1.8 0.039
32 14 0.6 7 750 1 730 790 177 22 000 26 000 2201 16 28 0.6 0.58 1.7 1.1 1.1 0.048
37 12 1 9 650 2 160 985 221 18 000 22 000 1301 17 32 1 0.33 2.9 1.9 2.0 0.066
37 17 1 12 100 2 730 1 240 278 17 000 22 000 2301 17 32 1 0.60 1.6 1.1 1.1 0.082
15 35 11 0.6 7 600 1 750 775 179 18 000 22 000 1202 19 31 0.6 0.32 3.1 2.0 2.1 0.051
35 14 0.6 7 800 1 850 795 188 18 000 22 000 2202 19 31 0.6 0.50 1.9 1.3 1.3 0.055
42 13 1 9 700 2 290 990 234 16 000 20 000 1302 20 37 1 0.33 2.9 1.9 2.0 0.093
42 17 1 12 300 2 910 1 250 296 14 000 18 000 2302 20 37 1 0.51 1.9 1.2 1.3 0.108
17 40 12 0.6 8 000 2 010 815 205 16 000 20 000 1203 21 36 0.6 0.31 3.1 2.0 2.1 0.072
40 16 0.6 9 950 2 420 1 010 247 16 000 20 000 2203 21 36 0.6 0.50 1.9 1.3 1.3 0.085
47 14 1 12 700 3 200 1 300 325 14 000 17 000 1303 22 42 1 0.32 3.1 2.0 2.1 0.13
47 19 1 14 700 3 550 1 500 365 13 000 16 000 2303 22 42 1 0.51 1.9 1.2 1.3 0.15
20 47 14 1 10 000 2 610 1 020 266 14 000 17 000 1204 1204 K 25 42 1 0.29 3.4 2.2 2.3 0.12
47 18 1 12 800 3 300 1 310 340 14 000 17 000 2204 2204 K 25 42 1 0.47 2.1 1.3 1.4 0.133
52 15 1.1 12 600 3 350 1 280 340 12 000 15 000 1304 1304 K 26.5 45.5 1 0.29 3.4 2.2 2.3 0.165
52 21 1.1 18 500 4 700 1 880 480 11 000 14 000 2304 2304 K 26.5 45.5 1 0.50 1.9 1.2 1.3 0.193
25 52 15 1 12 200 3 300 1 250 335 12 000 14 000 1205 1205 K 30 47 1 0.28 3.5 2.3 2.4 0.14
52 18 1 12 400 3 450 1 270 350 12 000 14 000 2205 2205 K 30 47 1 0.41 2.4 1.5 1.6 0.15
62 17 1.1 18 200 5 000 1 850 510 10 000 13 000 1305 1305 K 31.5 55.5 1 0.28 3.5 2.3 2.4 0.255
62 24 1.1 24 900 6 600 2 530 675 9 500 12 000 2305 2305 K 31.5 55.5 1 0.47 2.1 1.4 1.4 0.319
30 62 16 1 15 800 4 650 1 610 475 10 000 12 000 1206 1206 K 35 57 1 0.25 3.9 2.5 2.6 0.22
62 20 1 15 300 4 550 1 560 460 10 000 12 000 2206 2206 K 35 57 1 0.38 2.5 1.6 1.7 0.249
72 19 1.1 21 400 6 300 2 190 645 8 500 11 000 1306 1306 K 36.5 65.5 1 0.26 3.7 2.4 2.5 0.385
72 27 1.1 32 000 8 750 3 250 895 8 000 10 000 2306 2306 K 36.5 65.5 1 0.44 2.2 1.4 1.5 0.48
Note (1) The suffix K represents bearings with tapered bores (1 : 12)
Remarks For the dimensions related to adapters, refer to Page B358.
B 78 B 79
B076-083E.indd 78-79 11/20/13 4:55:41 PM

B B
r r ra
r
ra
jd
jD a jda
Fa/ Fre Fa/ Fr>e
X Y X Y
1 Y3 0.65 Y2
P0 =Fr +Y0 Fa

35 72 17 1.1 15 900 5 100 1 620 520 8 500 10 000 1207 1207 K 41.5 65.5 1 0.23 4.2 2.7 2.8 0.32
72 23 1.1 21 700 6 600 2 210 675 8 500 10 000 2207 2207 K 41.5 65.5 1 0.37 2.6 1.7 1.8 0.378
80 21 1.5 25 300 7 850 2 580 800 7 500 9 500 1307 1307 K 43 72 1.5 0.26 3.8 2.5 2.6 0.51
80 31 1.5 40 000 11 300 4 100 1 150 7 100 9 000 2307 2307 K 43 72 1.5 0.46 2.1 1.4 1.4 0.642
40 80 18 1.1 19 300 6 500 1 970 665 7 500 9 000 1208 1208 K 46.5 73.5 1 0.22 4.3 2.8 2.9 0.415
80 23 1.1 22 400 7 350 2 290 750 7 500 9 000 2208 2208 K 46.5 73.5 1 0.33 3.0 1.9 2.0 0.477
90 23 1.5 29 800 9 700 3 050 990 6 700 8 500 1308 1308 K 48 82 1.5 0.24 4.0 2.6 2.7 0.715
90 33 1.5 45 500 13 500 4 650 1 380 6 300 8 000 2308 2308 K 48 82 1.5 0.43 2.3 1.5 1.5 0.889
45 85 19 1.1 22 000 7 350 2 240 750 7 100 8 500 1209 1209 K 51.5 78.5 1 0.21 4.7 3.0 3.1 0.465
85 23 1.1 23 300 8 150 2 380 830 7 100 8 500 2209 2209 K 51.5 78.5 1 0.30 3.2 2.1 2.2 0.522
100 25 1.5 38 500 12 700 3 900 1 300 6 000 7 500 1309 1309 K 53 92 1.5 0.25 4.0 2.6 2.7 0.955
100 36 1.5 55 000 16 700 5 600 1 700 5 600 7 100 2309 2309 K 53 92 1.5 0.41 2.4 1.5 1.6 1.2
50 90 20 1.1 22 800 8 100 2 330 830 6 300 8 000 1210 1210 K 56.5 83.5 1 0.21 4.7 3.1 3.2 0.525
90 23 1.1 23 300 8 450 2 380 865 6 300 8 000 2210 2210 K 56.5 83.5 1 0.28 3.4 2.2 2.3 0.564
110 27 2 43 500 14 100 4 450 1 440 5 600 6 700 1310 1310 K 59 101 2 0.23 4.2 2.7 2.8 1.25
110 40 2 65 000 20 200 6 650 2 060 5 000 6 300 2310 2310 K 59 101 2 0.42 2.3 1.5 1.6 1.58
55 100 21 1.5 26 900 10 000 2 750 1 020 6 000 7 100 1211 1211 K 63 92 1.5 0.20 4.9 3.2 3.3 0.705
100 25 1.5 26 700 9 900 2 720 1 010 6 000 7 100 2211 2211 K 63 92 1.5 0.28 3.5 2.3 2.4 0.746
120 29 2 51 500 17 900 5 250 1 820 5 000 6 300 1311 1311 K 64 111 2 0.23 4.2 2.7 2.8 1.6
120 43 2 76 500 24 000 7 800 2 450 4 800 6 000 2311 2311 K 64 111 2 0.41 2.4 1.5 1.6 2.03
60 110 22 1.5 30 500 11 500 3 100 1 180 5 300 6 300 1212 1212 K 68 102 1.5 0.18 5.3 3.4 3.6 0.90
110 28 1.5 34 000 12 600 3 500 1 290 5 300 6 300 2212 2212 K 68 102 1.5 0.28 3.5 2.3 2.4 1.03
130 31 2.1 57 500 20 800 5 900 2 130 4 500 5 600 1312 1312 K 71 119 2 0.23 4.3 2.8 2.9 2.03
130 46 2.1 88 500 28 300 9 000 2 880 4 300 5 300 2312 2312 K 71 119 2 0.40 2.4 1.6 1.6 2.57
65 120 23 1.5 31 000 12 500 3 150 1 280 4 800 6 000 1213 1213 K 73 112 1.5 0.17 5.7 3.7 3.8 1.15
120 31 1.5 43 500 16 400 4 450 1 670 4 800 6 000 2213 2213 K 73 112 1.5 0.28 3.5 2.3 2.4 1.4
140 33 2.1 62 500 22 900 6 350 2 330 4 300 5 300 1313 1313 K 76 129 2 0.23 4.2 2.7 2.9 2.54
140 48 2.1 97 000 32 500 9 900 3 300 3 800 4 800 2313 2313 K 76 129 2 0.39 2.5 1.6 1.7 3.2
70 125 24 1.5 35 000 13 800 3 550 1 410 4 800 5 600 1214 78 117 1.5 0.18 5.3 3.4 3.6 1.3
125 31 1.5 44 000 17 100 4 500 1 740 4 500 5 600 2214 78 117 1.5 0.26 3.7 2.4 2.5 1.52
150 35 2.1 75 000 27 700 7 650 2 830 4 000 5 000 1314 81 139 2 0.22 4.4 2.8 3.0 3.19
150 51 2.1 111 000 37 500 11 300 3 850 3 600 4 500 2314 81 139 2 0.38 2.6 1.7 1.8 3.9
Note (1) The suffix K represents bearings with tapered bores (1 : 12)
Remarks For the dimensions related to adapters, refer to Page B358 and B359.
B 80 B 81
B076-083E.indd 80-81 11/20/13 4:55:42 PM

B B
r r ra
r
ra
jd
jD a jda
Fa/ Fre Fa/ Fr>e
X Y X Y
1 Y3 0.65 Y2
P0 =Fr +Y0 Fa

75 130 25 1.5 39 000 15 700 4 000 1 600 4 300 5 300 1215 1215 K 83 122 1.5 0.17 5.6 3.6 3.8 1.41
130 31 1.5 44 500 17 800 4 550 1 820 4 300 5 300 2215 2215 K 83 122 1.5 0.25 3.9 2.5 2.6 1.6
160 37 2.1 80 000 30 000 8 150 3 050 3 800 4 500 1315 1315 K 86 149 2 0.22 4.4 2.8 2.9 3.65
160 55 2.1 125 000 43 000 12 700 4 400 3 400 4 300 2315 2315 K 86 149 2 0.38 2.5 1.6 1.7 4.77
80 140 26 2 40 000 17 000 4 100 1 730 4 000 5 000 1216 1216 K 89 131 2 0.16 6.0 3.9 4.1 1.73
140 33 2 49 000 19 900 5 000 2 030 4 000 5 000 2216 2216 K 89 131 2 0.25 3.9 2.5 2.7 1.97
170 39 2.1 89 000 33 000 9 100 3 400 3 600 4 300 1316 1316 K 91 159 2 0.22 4.5 2.9 3.1 4.31
170 58 2.1 130 000 45 000 13 200 4 600 3 200 4 000 * 2316 * 2316 K 91 159 2 0.39 2.5 1.6 1.7 5.54
85 150 28 2 49 500 20 800 5 050 2 120 3 800 4 500 1217 1217 K 94 141 2 0.17 5.7 3.7 3.8 2.09
150 36 2 58 500 23 600 5 950 2 400 3 800 4 800 2217 2217 K 94 141 2 0.25 3.9 2.5 2.6 2.48
180 41 3 98 500 38 000 10 000 3 850 3 400 4 000 1317 1317 K 98 167 2.5 0.21 4.6 2.9 3.1 5.13
180 60 3 142 000 51 500 14 500 5 250 3 000 3 800 2317 2317 K 98 167 2.5 0.37 2.6 1.7 1.8 6.56
90 160 30 2 57 500 23 500 5 850 2 400 3 600 4 300 1218 1218 K 99 151 2 0.17 5.8 3.8 3.9 2.55
160 40 2 70 500 28 700 7 200 2 930 3 600 4 300 2218 2218 K 99 151 2 0.27 3.7 2.4 2.5 3.13
190 43 3 117 000 44 500 12 000 4 550 3 200 3 800 * 1318 * 1318 K 103 177 2.5 0.22 4.3 2.8 2.9 5.94
190 64 3 154 000 57 500 15 700 5 850 2 800 3 600 2318 2318 K 103 177 2.5 0.38 2.6 1.7 1.7 7.76
95 170 32 2.1 64 000 27 100 6 550 2 770 3 400 4 000 1219 1219 K 106 159 2 0.17 5.8 3.7 3.9 3.21
170 43 2.1 84 000 34 500 8 550 3 500 3 400 4 000 2219 2219 K 106 159 2 0.27 3.7 2.4 2.5 3.87
200 45 3 129 000 51 000 13 200 5 200 3 000 3 600 * 1319 * 1319 K 108 187 2.5 0.23 4.3 2.8 2.9 6.84
200 67 3 161 000 64 500 16 400 6 550 2 800 3 400 * 2319 * 2319 K 108 187 2.5 0.38 2.6 1.7 1.8 9.01
100 180 34 2.1 69 500 29 700 7 100 3 050 3 200 3 800 1220 1220 K 111 169 2 0.17 5.6 3.6 3.8 3.82
180 46 2.1 94 500 38 500 9 650 3 900 3 200 3 800 2220 2220 K 111 169 2 0.27 3.7 2.4 2.5 4.53
215 47 3 140 000 57 500 14 300 5 850 2 800 3 400 * 1320 * 1320 K 113 202 2.5 0.24 4.1 2.7 2.8 8.46
215 73 3 187 000 79 000 19 100 8 050 2 400 3 200 * 2320 * 2320 K 113 202 2.5 0.38 2.6 1.7 1.8 11.6
105 190 36 2.1 75 000 32 500 7 650 3 300 3 000 3 600 1221 116 179 2 0.18 5.5 3.6 3.7 4.52
190 50 2.1 109 000 45 000 11 100 4 550 3 000 3 600 2221 116 179 2 0.28 3.5 2.3 2.4 5.64
225 49 3 154 000 64 500 15 700 6 600 2 600 3 200 * 1321 118 212 2.5 0.23 4.2 2.7 2.9 10
225 77 3 200 000 87 000 20 400 8 850 2 400 3 000 * 2321 118 212 2.5 0.38 2.6 1.7 1.7 14.4
110 200 38 2.1 87 000 38 500 8 900 3 950 2 800 3 400 1222 1222 K 121 189 2 0.17 5.7 3.7 3.9 5.33
200 53 2.1 122 000 51 500 12 500 5 250 2 800 3 400 * 2222 * 2222 K 121 189 2 0.28 3.5 2.2 2.3 6.64
240 50 3 161 000 72 000 16 400 7 300 2 400 3 000 * 1322 * 1322 K 123 227 2.5 0.22 4.4 2.8 3.0 12
240 80 3 211 000 94 500 21 600 9 650 2 200 2 800 * 2322 * 2322 K 123 227 2.5 0.37 2.6 1.7 1.8 17.4
Notes (1) The suffix K represents bearings with tapered bores (1 : 12)
(*) The balls of the bearings marked * protrude slightly from the bearing face. The protrusion amounts are shown on
Page B77.
Remarks For the dimensions related to adapters, refer to Pages B360 and B361.
B 82 B 83
B076-083E.indd 82-83 11/20/13 4:55:43 PM

CYLINDRICAL ROLLER BEARINGS
SINGLE-ROW CYLINDRICAL ROLLER BEARINGS Bore Diameter 20 65mm B 88
Bore Diameter 70 160mm B 94
L-SHAPED THRUST COLLARS FOR CYLINDRICAL ROLLER BEARINGS Bore Diameter 20 320mm B106
DOUBLE-ROW CYLINDRICAL ROLLER BEARINGS Bore Diameter 25 360mm B110

Four-Row Cylindrical Roller Bearings are described on Pages B334 to B343.

Depending on the existence of ribs on their rings, Cylindrical Roller
Bearings are classified into the following types.
NU NJ NUP N NF NH
NNU NN
Types NU, N, NNU, and NN are suitable as free-end bearings. Types NJ and
NF can sustain limited axial loads in one direction. Types NH and NUP can be
used as fixed-end bearings.
NH-type cylindrical roller bearings consist of the NJ-type cylindrical roller
bearings and HJ-type L-shaped thrust collars (See Page B104 to B105).
The inner ring loose rib of a NUP-type cylindrical roller bearing should be
mounted so that the marked side is on the outside.
B 84 B 85
B084-109E.indd 84-85 11/20/13 4:56:07 PM

Use pressed, machined, or molded cages for standard cylindrical roller
Table 2 Tolerances for Roller Inscribed Circle Diameter Fw and
bearings as shown in Table 1. Roller Circumscribed Circle Diameter Ew of Cylindrical
Roller Bearings Having Interchangeable Rings
Table 1 Standard Cages for Cylindrical Roller Bearings Units : m
Nominal Bore Tolerances for Fw of types Tolerances for Ew of
Series Pressed Steel Cages (W) Machined Brass Cages (M) Molded Polyamide Cages (T) Diameter d (mm) NU, NJ, NUP, NH, and NNU & Fw types N, NF, and NN & Ew
NU10** 1005 10/500
20 +10 0 0 10
N2** 204 230 232 264 20 50 +15 0 0 15
NU2** 214 230 232 264 50 120 +20 0 0 20
NU2**E 205E 213E 214E 240E 204E 120 200 +25 0 0 25
200 250 +30 0 0 30
NU22** 2204 2230 2232 2252 250 315 +35 0 0 35
NU22**E 2222E 2240E 2204E 2220E 315 400 +40 0 0 40
N3** 304 324 326 352 400 500 +45 0
NU3** 312 330 332 352
NU3**E 305E 311E 312E 340E 304E RECOMMENDED FITS
NU23** 2304 2320 2322 2340
NU23**E 2322E 2340E 2304E 2320E
CYLINDRICAL ROLLER BEARINGSTable 9.2 (Page A84)
NU4** 405 416 417 430 Table 9.4 (Page A85)
DOUBLE-ROW CYLINDRICAL ROLLER
The basic load ratings listed in the bearing tables are based on the Cage BEARINGS Table 9.2 (Page A84)
Classification in Table 1. Table 9.4 (Page A85)
For a given bearing number, if the type of cage is not the standard one, the
number of rollers may vary; in such a case, the load rating will differ from the
one listed in the bearing tables. INTERNAL CLEARANCES
Among the NN Type of double-row bearings, there are many of high
precision that have tapered bores, and they are primarily used in the main CYLINDRICAL ROLLER BEARINGSTable 9.14 (Page A91)
spindles of machine tools. Their cages are either molded polyphenylenesulfide DOUBLE-ROW CYLINDRICAL ROLLER BEARINGS Table 9.14 (Page A91)
(PPS) or machined brass.
PRECAUTIONS FOR USE OF CYLINDRICAL ROLLER BEARINGS
The permissible misalignment of cylindrical roller bearings varies depending
If the load on cylindrical roller bearings becomes too small during operation, on the type and internal specifications, but under normal loads, the angles are
slippage between the rollers and raceways occurs, which may result in approximately as follows:
smearing. Especially with large bearings since the weight of the roller and cage Cylindrical Roller Bearings of width series 0 or 1 0.0012 radian (4)
is high. Cylindrical Roller Bearings of width series 2 0.0006 radian (2)
In case of strong shock loads or vibration, pressed-steel cages are For double-row cylindrical roller bearings, nearly no misalignment is
sometimes inadequate. allowed.
If very small bearing load or strong shock loads or vibration are expected,
please consult with NSK for selection of the bearings.
Bearings with molded polyamide cages (ET type) can be used continuously LIMITING SPEEDS
at temperatures between 40 and 120C. If the bearings are used in gear
oil, nonflammable hydraulic oil, or ester oil at a high temperature over 100C, The limiting speeds listed in the bearing tables should be adjusted depending
please contact NSK beforehand. on the bearing load conditions. Also, higher speeds are attainable by making
changes in the lubrication method, cage design, etc. Refer to Page A37 for
TOLERANCES AND RUNNING ACCURACY detailed information.
CYLINDRICAL ROLLER BEARINGS Table 8.2 (Pages A60 to A63)

DOUBLE-ROW CYLINDRICAL ROLLER
BEARINGS Table 8.2 (Pages A60 to A63)
B 86 B 87
B084-109E.indd 86-87 11/20/13 4:56:08 PM

SINGLE-ROW CYLINDRICAL ROLLER BEARINGS
B B
r r r r1 r r1 ra rb ra
r1 r1 r r r1 r r
rb ra
jD jFw jd jFw jFw jD jEw jd jEw jDa jdb jdb jdc jDb jda jDb jDa jdb jdd
NU NJ NUP N NF
Boundary Dimensions Basic Load Ratings Limiting Speeds(1) Bearing Numbers(2) Abutment and Fillet Dimensions Mass
(mm) (N) (min 1) (mm) (kg)
(3)
d D B r r1 FW EW Cr C 0r Grease Oil NU NJ NUP N NF da(4) db db(5) dc dd Da(4) Db Db ra rb
min. min. min. min. max. min. min. max. max. min. max. max. approx.
20 47 14 1 0.6 40 15 400 12 700 15 000 18 000 N 204 N NF 25 43 42 1 0.6 0.107

47 14 1 0.6 26.5 25 700 22 600 13 000 16 000 NU 204 ET NU NJ NUP 25 24 25 29 32 42 1 0.6 0.107
47 18 1 0.6 27 20 700 18 400 13 000 16 000 NU 2204 NU NJ 25 24 25 29 32 42 1 0.6 0.144
47 18 1 0.6 26.5 30 500 28 300 13 000 16 000 NU 2204 ET NU NJ NUP 25 24 25 29 32 42 1 0.6 0.138
52 15 1.1 0.6 44.5 21 400 17 300 12 000 15 000 N 304 N NF 26.5 48 46 1 0.6 0.148
52 15 1.1 0.6 27.5 31 500 26 900 12 000 15 000 NU 304 ET NU NJ NUP 26.5 24 26 30 33 45.5 1 0.6 0.145
52 21 1.1 0.6 28.5 30 500 27 200 11 000 14 000 NU 2304 NU NJ NUP 26.5 24 27 30 33 45.5 1 0.6 0.217
52 21 1.1 0.6 27.5 42 000 39 000 11 000 14 000 NU 2304 ET NU NJ NUP 26.5 24 26 30 33 45.5 1 0.6 0.209
25 47 12 0.6 0.3 30.5 14 300 13 100 15 000 18 000 NU 1005 NU 27 30 32 43 0.6 0.3 0.094
52 15 1 0.6 45 17 700 15 700 13 000 16 000 N 205 N NF 30 48 46 1 0.6 0.135
52 15 1 0.6 31.5 29 300 27 700 12 000 14 000 NU 205 EW NU NJ NUP 30 29 30 34 37 47 1 0.6 0.136
52 18 1 0.6 31.5 35 000 34 500 12 000 14 000 NU 2205 ET NU NJ NUP 30 29 30 34 37 47 1 0.6 0.16
62 17 1.1 1.1 53 29 300 25 200 10 000 13 000 N 305 N NF 31.5 55.5 50 1 1 0.233
62 17 1.1 1.1 34 41 500 37 500 10 000 12 000 NU 305 EW NU NJ NUP 31.5 31.5 32 37 40 55.5 1 1 0.269
62 24 1.1 1.1 34 57 000 56 000 9 000 11 000 NU 2305 ET NU NJ NUP 31.5 31.5 32 37 40 55.5 1 1 0.338
80 21 1.5 1.5 38.8 62.8 46 500 40 000 9 000 11 000 NU 405 NU NJ N NF 33 33 37 41 46 72 72 64 1.5 1.5 0.57
30 55 13 1 0.6 36.5 48.5 19 700 19 600 12 000 15 000 NU 1006 NU N 35 34 36 38 50 51 49 1 0.5 0.136
62 16 1 0.6 53.5 24 900 23 300 11 000 13 000 N 206 N NF 35 58 56 1 0.6 0.208
62 16 1 0.6 37.5 39 000 37 500 9 500 12 000 NU 206 EW NU NJ NUP 35 34 36 40 44 57 1 0.6 0.205
62 20 1 0.6 37.5 49 000 50 000 9 500 12 000 NU 2206 ET NU NJ NUP 35 34 36 40 44 57 1 0.6 0.255
72 19 1.1 1.1 62 38 500 35 000 8 500 11 000 N 306 N NF 36.5 65.5 64 1 1 0.353
72 19 1.1 1.1 40.5 53 000 50 000 8 500 10 000 NU 306 EW NU NJ NUP 36.5 36.5 39 44 48 65.5 1 1 0.409
72 27 1.1 1.1 40.5 74 500 77 500 8 000 9 500 NU 2306 ET NU NJ NUP 36.5 36.5 39 44 48 65.5 1 1 0.518
90 23 1.5 1.5 45 73 62 500 55 000 7 500 9 500 NU 406 NU NJ N NF 38 38 43 47 52 82 82 75 1.5 1.5 0.758
35 62 14 1 0.6 42 55 22 600 23 200 11 000 13 000 NU 1007 NU NJ N 40 39 41 44 57 58 56 1 0.5 0.18
72 17 1.1 0.6 61.8 35 500 34 000 9 500 11 000 N 207 N NF 41.5 68 64 1 0.6 0.301
72 17 1.1 0.6 44 50 500 50 000 8 500 10 000 NU 207 EW NU NJ NUP 41.5 39 42 46 50 65.5 1 0.6 0.304
72 23 1.1 0.6 44 61 500 65 500 8 500 10 000 NU 2207 ET NU NJ NUP 41.5 39 42 46 50 65.5 1 0.6 0.40
80 21 1.5 1.1 68.2 49 500 47 000 8 000 9 500 N 307 N NF 43 73.5 70 1.5 1 0.476
80 21 1.5 1.1 46.2 66 500 65 500 7 500 9 500 NU 307 EW NU NJ NUP 41.5 41.5 44 48 53 72 1.5 1 0.545
80 31 1.5 1.1 46.2 93 000 101 000 6 700 8 500 NU 2307 ET NU NJ NUP 43 41.5 44 48 53 72 1.5 1 0.711
100 25 1.5 1.5 53 83 75 500 69 000 6 700 8 000 NU 407 NU NJ N NF 43 43 51 55 61 92 92 85 1.5 1.5 1.01
Notes (1) The limiting speeds listed above apply to bearings with machined cages (No suffix). For bearings with pressed cages, Notes (3) When L-shaped thrust collars (See section for L-Shaped Thrust Collars starting on page B104) are used, the bearings
reduce the limiting speed by 20%. (Not applicable to bearing numbers with an EM, EW, or ET suffix.) become the NH type.
(2) The bearings with suffix ET have polyamide cage. The maximum operating temperature should be less than 120 C. (4) If axial loads are applied, increase da and reduce Da from the values listed above.
(5) db (max.) are values for adjusting rings for NU, NJ Types.
B 88 B 89
B084-109E.indd 88-89 11/20/13 4:56:08 PM

B B
r1 r1 r r r1 r r
rb ra
NU NJ NUP N NF
(mm) (N) (min 1) (mm) (kg)
(3)
40 68 15 1 0.6 47 61 27 300 29 000 10 000 12 000 NU 1008 NU NJ NUP N 45 44 46 49 63 64 62 1 0.6 0.223

80 18 1.1 1.1 70 43 500 43 000 8 500 10 000 N 208 N NF 46.5 73.5 72 1 1 0.375
80 18 1.1 1.1 49.5 55 500 55 500 7 500 9 000 NU 208 EW NU NJ NUP 46.5 46.5 48 52 56 73.5 1 1 0.379
80 23 1.1 1.1 49.5 72 500 77 500 7 500 9 000 NU 2208 ET NU NJ NUP 46.5 46.5 48 52 56 73.5 1 1 0.480
90 23 1.5 1.5 77.5 58 500 57 000 6 700 8 500 N 308 N NF 48 82 79 1.5 1.5 0.649
90 23 1.5 1.5 52 83 000 81 500 6 700 8 000 NU 308 EW NU NJ NUP 48 48 50 55 60 82 1.5 1.5 0.747
90 33 1.5 1.5 52 114 000 122 000 6 000 7 500 NU 2308 ET NU NJ NUP 48 48 50 55 60 82 1.5 1.5 0.933
110 27 2 2 58 92 95 500 89 000 6 000 7 500 NU 408 NU NJ NUP N NF 49 49 56 60 67 101 101 94 2 2 1.28
45 75 16 1 0.6 52.5 67.5 32 500 35 500 9 000 11 000 NU 1009 NU N NF 50 49 51 54 70 71 68 1 0.6 0.279
85 19 1.1 1.1 75 46 000 47 000 7 500 9 000 N 209 N NF 51.5 78.5 77 1 1 0.429
85 19 1.1 1.1 54.5 63 000 66 500 6 700 8 000 NU 209 EW NU NJ NUP 51.5 51.5 52 57 61 78.5 1 1 0.438
85 23 1.1 1.1 54.5 76 000 84 500 6 700 8 500 NU 2209 ET NU NJ NUP 51.5 51.5 52 57 61 78.5 1 1 0.521
100 25 1.5 1.5 86.5 79 000 77 500 6 300 7 500 N 309 N NF 53 92 77 1.5 1.5 0.869
100 25 1.5 1.5 58.5 97 500 98 500 6 000 7 500 NU 309 EW NU NJ NUP 53 53 56 60 66 92 1.5 1.5 1.01
100 36 1.5 1.5 58.5 137 000 153 000 5 300 6 700 NU 2309 ET NU NJ NUP 53 53 56 60 66 92 1.5 1.5 1.28
120 29 2 2 64.5 100.5 107 000 102 000 5 600 6 700 NU 409 NU NJ NUP N NF 54 54 62 66 74 111 111 103 2 2 1.62
50 80 16 1 0.6 57.5 72.5 32 000 36 000 8 000 10 000 NU 1010 NU NJ NUP N 55 54 56 59 75 76 73 1 0.6 0.301
90 20 1.1 1.1 80.4 48 000 51 000 7 100 8 500 N 210 N NF 56.5 83.5 82 1 1 0.483
90 20 1.1 1.1 59.5 69 000 76 500 6 300 7 500 NU 210 EW NU NJ NUP 56.5 56.5 57 62 67 83.5 1 1 0.50
90 23 1.1 1.1 59.5 83 500 97 000 6 300 8 000 NU 2210 ET NU NJ NUP 56.5 56.5 57 62 67 83.5 1 1 0.562
110 27 2 2 95 87 000 86 000 5 600 6 700 N 310 N NF 59 101 97 2 2 1.11
110 27 2 2 65 110 000 113 000 5 000 6 000 NU 310 EW NU NJ NUP 59 59 63 67 73 101 2 2 1.3
110 40 2 2 65 163 000 187 000 5 000 6 300 NU 2310 ET NU NJ NUP 59 59 63 67 73 101 2 2 1.7
130 31 2.1 2.1 110.8 139 000 136 000 5 000 6 000 N 410 N NF 65 117 113 2 2 2.0
130 31 2.1 2.1 70.8 110.8 129 000 124 000 5 000 6 000 NU 410 NU NJ NUP N NF 61 61 68 73 81 119 119 113.3 2 2 1.99
55 90 18 1.1 1 64.5 80.5 37 500 44 000 7 500 9 000 NU 1011 NU NJ N 61.5 60 63 66 83.5 85 82 1 1 0.445
100 21 1.5 1.1 88.5 58 000 62 500 6 300 7 500 N 211 N NF 63 93.5 91 1.5 1 0.634
100 21 1.5 1.1 66 86 500 98 500 5 600 7 100 NU 211 EW NU NJ NUP 63 61.5 64 68 73 92 1.5 1 0.669
100 25 1.5 1.1 66 101 000 122 000 5 600 7 100 NU 2211 ET NU NJ NUP 63 61.5 64 68 73 92 1.5 1 0.783
120 29 2 2 104.5 111 000 111 000 5 000 6 300 N 311 N NF 64 111 107 2 2 1.42
120 29 2 2 70.5 137 000 143 000 4 500 5 600 NU 311 EW NU NJ NUP 64 64 68 72 80 111 2 2 1.64
120 43 2 2 70.5 201 000 233 000 4 500 5 600 NU 2311 ET NU NJ NUP 64 64 68 72 80 111 2 2 2.18
140 33 2.1 2.1 77.2 117.2 139 000 138 000 4 500 5 600 NU 411 NU NJ NUP N NF 66 66 75 79 87 129 129 119 2 2 2.5
B 90 B 91
B084-109E.indd 90-91 11/20/13 4:56:10 PM

B B
r1 r1 r r r1 r r
rb ra
NU NJ NUP N NF
(mm) (N) (min 1) (mm) (kg)
(3)
60 95 18 1.1 1 69.5 85.5 40 000 48 500 6 700 8 500 NU 1012 NU NJ N NF 66.5 65 68 71 88.5 90 87 1 1 0.474
110 22 1.5 1.5 97.5 68 500 75 000 6 000 7 100 N 212 N NF 68 102 100 1.5 1.5 0.823
110 22 1.5 1.5 72 97 500 107 000 5 300 6 300 NU 212 EW NU NJ NUP 68 68 70 75 80 102 1.5 1.5 0.824
110 28 1.5 1.5 72 131 000 157 000 5 300 6 300 NU 2212 ET NU NJ NUP 68 68 70 75 80 102 1.5 1.5 1.06
130 31 2.1 2.1 113 124 000 126 000 4 800 5 600 N 312 N NF 71 119 115 2 2 1.78
130 31 2.1 2.1 77 124 000 126 000 4 800 5 600 NU 312 NU NJ NUP 71 71 75 79 86 119 2 2 1.82
130 31 2.1 2.1 77 150 000 157 000 4 800 5 600 NU 312 EM NU NJ NUP 71 71 75 79 86 119 2 2 2.06
130 46 2.1 2.1 77 222 000 262 000 4 300 5 300 NU 2312 ET NU NJ NUP 71 71 75 79 86 119 2 2 2.7
150 35 2.1 2.1 83 127 167 000 168 000 4 300 5 300 NU 412 NU NJ NUP N NF 71 71 80 85 94 139 139 130 2 2 3.04
65 100 18 1.1 1 74.5 90.5 41 000 51 000 6 300 8 000 NU 1013 NU NJ N NF 71.5 70 73 76 93.5 95 92 1 1 0.504
120 23 1.5 1.5 105.6 84 000 94 500 5 300 6 300 N 213 N NF 73 112 108 1.5 1.5 1.05
120 23 1.5 1.5 78.5 108 000 119 000 4 800 5 600 NU 213 EW NU NJ NUP 73 73 76 81 87 112 1.5 1.5 1.05
120 31 1.5 1.5 78.5 149 000 181 000 4 800 6 000 NU 2213 ET NU NJ NUP 73 73 76 81 87 112 1.5 1.5 1.41
140 33 2.1 2.1 121.5 135 000 139 000 4 300 5 300 N 313 N NF 76 129 125 2 2 2.17
140 33 2.1 2.1 83.5 135 000 139 000 4 300 5 300 NU 313 NU NJ NUP 76 76 81 85 93 129 2 2 2.23
140 33 2.1 2.1 82.5 181 000 191 000 4 300 5 300 NU 313 EM NU NJ NUP 76 76 80 85 93 129 2 2 2.56
140 48 2.1 2.1 82.5 233 000 265 000 3 800 4 800 NU 2313 ET NU NJ NUP 76 76 80 85 93 129 2 2 3.16
160 37 2.1 2.1 89.3 135.3 182 000 186 000 4 000 4 800 NU 413 NU NJ N NF 76 76 86 91 100 149 149 138.8 2 2 3.63
70 110 20 1.1 1 80 100 58 500 70 500 6 000 7 100 NU 1014 NU NJ NUP N NF 76.5 75 79 82 103.5 105 101 1 1 0.693
125 24 1.5 1.5 110.5 83 500 95 000 5 000 6 300 N 214 N NF 78 117 113 1.5 1.5 1.14
125 24 1.5 1.5 83.5 119 000 137 000 5 000 6 300 NU 214 EM NU NJ NUP 78 78 81 86 92 117 1.5 1.5 1.29
125 31 1.5 1.5 83.5 156 000 194 000 4 500 5 600 NU 2214 ET NU NJ NUP 78 78 81 86 92 117 1.5 1.5 1.49
150 35 2.1 2.1 130 149 000 156 000 4 000 5 000 N 314 N NF 81 139 133.5 2 2 2.67
150 35 2.1 2.1 90 158 000 168 000 4 000 5 000 NU 314 NU NJ NUP 81 81 87 92 100 139 2 2 2.75
150 35 2.1 2.1 89 205 000 222 000 4 000 5 000 NU 314 EM NU NJ NUP 81 81 86 92 100 139 2 2 3.09
150 51 2.1 2.1 89 274 000 325 000 3 600 4 500 NU 2314 ET NU NJ NUP 81 81 86 92 100 139 2 2 3.92
180 42 3 3 100 152 228 000 236 000 3 600 4 300 NU 414 NU NJ NUP N NF 83 83 97 102 112 167 167 155 2.5 2.5 5.28
75 115 20 1.1 1 85 105 60 000 74 500 5 600 6 700 NU 1015 NU N NF 81.5 80 83 87 108.5 110 106 1 1 0.731
130 25 1.5 1.5 116.5 96 500 111 000 4 800 6 000 N 215 N NF 83 122 119 1.5 1.5 1.23
130 25 1.5 1.5 88.5 130 000 156 000 4 800 6 000 NU 215 EM NU NJ NUP 83 83 86 90 96 122 1.5 1.5 1.44
130 31 1.5 1.5 88.5 162 000 207 000 4 300 5 300 NU 2215 ET NU NJ NUP 83 83 86 90 96 122 1.5 1.5 1.57
160 37 2.1 2.1 139.5 179 000 189 000 3 800 4 800 N 315 N NF 86 149 143 2 2 3.2
160 37 2.1 2.1 95.5 179 000 189 000 3 800 4 800 NU 315 NU NJ NUP 86 86 93 97 106 149 2 2 3.26
160 37 2.1 2.1 95 240 000 263 000 3 800 4 800 NU 315 EM NU NJ NUP 86 86 92 97 106 149 2 2 3.73
160 55 2.1 2.1 95 330 000 395 000 3 400 4 300 NU 2315 ET NU NJ NUP 86 86 92 97 106 149 2 2 4.86
190 45 3 3 104.5 160.5 262 000 274 000 3 400 4 000 NU 415 NU NJ N NF 88 88 102 107 118 177 177 164 2.5 2.5 6.27
B 92 B 93
B084-109E.indd 92-93 11/20/13 4:56:12 PM

B B
r r r r ra rb ra
r1 r1
r1 r1 r r r1 r r
rb ra
NU NJ NUP N NF
(mm) (N) (min 1) (mm) (kg)
(3)
80 125 22 1.1 1 91.5 113.5 72 500 90 500 5 300 6 300 NU 1016 NU NUP N 86.5 85 90 94 118.5 120 115 1 1 0.969
140 26 2 2 125.3 106 000 122 000 4 500 5 300 N 216 N NF 89 131 128 2 2 1.47
140 26 2 2 95.3 139 000 167 000 4 500 5 300 NU 216 EM NU NJ NUP 89 89 92 97 104 131 2 2 1.7
140 33 2 2 95.3 186 000 243 000 4 000 5 000 NU 2216 ET NU NJ NUP 89 89 92 97 104 131 2 2 1.96
170 39 2.1 2.1 147 190 000 207 000 3 600 4 300 N 316 N NF 91 159 150 2 2 3.85
170 39 2.1 2.1 101 256 000 282 000 3 600 4 300 NU 316 EM NU NJ NUP 91 91 98 105 114 159 2 2 4.45
170 58 2.1 2.1 101 355 000 430 000 3 200 4 000 NU 2316 ET NU NJ NUP 91 91 98 105 114 159 2 2 5.73
200 48 3 3 110 170 299 000 315 000 3 200 3 800 NU 416 NU NJ N NF 93 93 107 112 124 187 187 173 2.5 2.5 7.36
85 130 22 1.1 1 96.5 118.5 74 500 95 500 5 000 6 000 NU 1017 NU N 91.5 90 95 99 123.5 125 120 1 1 1.01
150 28 2 2 133.8 120 000 140 000 4 300 5 000 N 217 N NF 94 141 137 2 2 1.87
150 28 2 2 100.5 167 000 199 000 4 300 5 000 NU 217 EM NU NJ NUP 94 94 98 104 110 141 2 2 2.11
150 36 2 2 100.5 217 000 279 000 3 800 4 500 NU 2217 ET NU NJ NUP 94 94 98 104 110 141 2 2 2.44
180 41 3 3 156 225 000 247 000 3 400 4 000 N 317 N NF 98 167 159 2.5 2.5 4.53
180 41 3 3 108 212 000 228 000 3 400 4 000 NU 317 NU NJ NUP 98 98 105 110 119 167 2.5 2.5 4.6
180 41 3 3 108 291 000 330 000 3 400 4 000 NU 317 EM NU NJ NUP 98 98 105 110 119 167 2.5 2.5 5.26
180 60 3 3 108 395 000 485 000 3 000 3 800 NU 2317 ET NU NJ NUP 98 98 105 110 119 167 2.5 2.5 6.77
210 52 4 4 113 177 335 000 350 000 3 000 3 800 NU 417 NU NJ N NF 101 101 110 115 128 194 194 180 3 3 9.56
90 140 24 1.5 1.1 103 127 88 000 114 000 4 500 5 600 NU 1018 NU NUP N 98 96.5 101 106 132 133.5 129 1.5 1 1.35
160 30 2 2 143 152 000 178 000 4 000 4 800 N 218 N NF 99 151 146 2 2 2.31
160 30 2 2 107 182 000 217 000 4 000 4 800 NU 218 EM NU NJ NUP 99 99 104 109 116 151 2 2 2.6
160 40 2 2 107 242 000 315 000 3 600 4 300 NU 2218 ET NU NJ NUP 99 99 104 109 116 151 2 2 3.11
190 43 3 3 165 240 000 265 000 3 200 3 800 N 318 N NF 103 177 168 2.5 2.5 5.31
190 43 3 3 115 240 000 265 000 3 200 3 800 NU 318 NU NJ NUP 103 103 112 117 127 177 2.5 2.5 5.38
190 43 3 3 113.5 315 000 355 000 3 200 3 800 NU 318 EM NU NJ NUP 103 103 111 117 127 177 2.5 2.5 6.1
190 64 3 3 113.5 435 000 535 000 2 800 3 400 NU 2318 ET NU NJ NUP 103 103 111 117 127 177 2.5 2.5 7.9
225 54 4 4 123.5 191.5 375 000 400 000 2 800 3 400 NU 418 NU NJ N NF 106 106 120 125 139 209 209 196 3 3 11.5
95 145 24 1.5 1.1 108 132 90 500 120 000 4 300 5 300 NU 1019 NU NJ N 103 101.5 106 111 137 138.5 134 1.5 1 1.41
170 32 2.1 2.1 151.5 166 000 196 000 3 800 4 500 N 219 N NF 106 159 155 2 2 2.79
170 32 2.1 2.1 112.5 220 000 265 000 3 800 4 500 NU 219 EM NU NJ NUP 106 106 110 116 123 159 2 2 3.17
170 43 2.1 2.1 112.5 286 000 370 000 3 400 4 000 NU 2219 ET NU NJ NUP 106 106 110 116 123 159 2 2 3.81
200 45 3 3 173.5 259 000 289 000 3 000 3 600 N 319 N NF 108 187 177 2.5 2.5 6.09
200 45 3 3 121.5 259 000 289 000 3 000 3 600 NU 319 NU NJ NUP 108 108 118 124 134 187 2.5 2.5 6.23
200 45 3 3 121.5 335 000 385 000 3 000 3 600 NU 319 EM NU NJ NUP 108 108 118 124 134 187 2.5 2.5 7.13
200 67 3 3 121.5 460 000 585 000 2 600 3 400 NU 2319 ET NU NJ NUP 108 108 118 124 134 187 2.5 2.5 9.21
240 55 4 4 133.5 201.5 400 000 445 000 2 600 3 200 NU 419 NU NJ NUP NF 111 111 130 136 149 224 224 206 3 3 13.6
B 94 B 95
B084-109E.indd 94-95 11/20/13 4:56:14 PM

B B
r r r r ra rb ra
r1 r1
r1 r1 r r r1 r r
rb ra
NU NJ NUP N NF
(mm) (N) (min 1) (mm) (kg)
(3)
100 150 24 1.5 1.1 113 137 93 000 126 000 4 300 5 300 NU 1020 NU NJ NUP N 108 106.5 111 116 142 143.5 139 1.5 1 1.47
180 34 2.1 2.1 160 183 000 217 000 3 600 4 300 N 220 N NF 111 169 163 2 2 3.36
180 34 2.1 2.1 119 249 000 305 000 3 600 4 300 NU 220 EM NU NJ NUP 111 111 116 122 130 169 2 2 3.81
180 46 2.1 2.1 119 335 000 445 000 3 200 3 800 NU 2220 ET NU NJ NUP 111 111 116 122 130 169 2 2 4.69
215 47 3 3 185.5 299 000 335 000 2 800 3 400 N 320 N NF 113 202 190 2.5 2.5 7.59
215 47 3 3 129.5 299 000 335 000 2 800 3 400 NU 320 NU NJ NUP 113 113 126 132 143 202 2.5 2.5 7.69
215 47 3 3 127.5 380 000 425 000 2 800 3 400 NU 320 EM NU NJ NUP 113 113 124 132 143 202 2.5 2.5 8.63
215 73 3 3 127.5 570 000 715 000 2 400 3 000 NU 2320 ET NU NJ NUP 113 113 124 132 143 202 2.5 2.5 11.8
250 58 4 4 139 211 450 000 500 000 2 600 3 000 NU 420 NU NJ N NF 116 116 135 141 156 234 234 215 3 3 15.5
105 160 26 2 1.1 119.5 145.5 109 000 149 000 4 000 4 800 NU 1021 NU N NF 114 111.5 118 122 151 153.5 147 2 1 1.83
190 36 2.1 2.1 168.8 201 000 241 000 3 400 4 000 N 221 N NF 116 179 172 2 2 4.0
190 36 2.1 2.1 125 262 000 310 000 3 400 4 000 NU 221 EM NU NJ NUP 116 116 121 129 137 179 2 2 4.58
225 49 3 3 195 340 000 390 000 2 600 3 200 N 321 N NF 118 212 199 2.5 2.5 8.69
225 49 3 3 133 425 000 480 000 2 600 3 200 NU 321 EM NU NJ NUP 118 118 131 137 149 212 2.5 2.5 9.84
260 60 4 4 144.5 220.5 495 000 555 000 2 400 3 000 NU 421 NU NJ N NF 121 121 141 147 162 244 244 225 3 3 17.3
110 170 28 2 1.1 125 155 131 000 174 000 3 800 4 500 NU 1022 NU NJ N NF 119 116.5 123 128 161 163.5 157 2 1 2.27
200 38 2.1 2.1 178.5 229 000 272 000 3 200 3 800 N 222 N NF 121 189 182 2 2 4.64
200 38 2.1 2.1 132.5 293 000 365 000 3 200 3 800 NU 222 EM NU NJ NUP 121 121 129 135 144 189 2 2 5.37
200 53 2.1 2.1 132.5 385 000 515 000 2 800 3 400 NU 2222 EM NU NJ NUP 121 121 129 135 144 189 2 2 7.65
240 50 3 3 207 380 000 435 000 2 600 3 000 N 322 N NF 123 227 211 2.5 2.5 10.3
240 50 3 3 143 450 000 525 000 2 600 3 000 NU 322 EM NU NJ NUP 123 123 139 145 158 227 2.5 2.5 11.8
280 65 4 4 155 550 000 620 000 2 200 2 800 NU 422 NU NJ 126 126 151 157 173 264 3 3 22.1
120 180 28 2 1.1 135 165 139 000 191 000 3 400 4 300 NU 1024 NU NJ NUP N 129 126.5 133 138 171 173.5 167 2 1 2.43
215 40 2.1 2.1 191.5 260 000 320 000 3 000 3 400 N 224 N NF 131 204 196 2 2 5.63
215 40 2.1 2.1 143.5 335 000 420 000 3 000 3 400 NU 224 EM NU NJ NUP 131 131 140 146 156 204 2 2 6.43
215 58 2.1 2.1 143.5 450 000 620 000 2 600 3 200 NU 2224 EM NU NJ NUP 131 131 140 146 156 204 2 2 9.51
260 55 3 3 226 450 000 510 000 2 200 2 800 N 324 N NF 133 247 230 2.5 2.5 12.9
260 55 3 3 154 530 000 610 000 2 200 2 800 NU 324 EM NU NJ NUP 133 133 150 156 171 247 2.5 2.5 15
260 86 3 3 154 795 000 1 030 000 2 000 2 600 NU 2324 EM NU NJ NUP 133 133 150 156 171 247 2.5 2.5 25
310 72 5 5 170 260 675 000 770 000 2 000 2 400 NU 424 NU NJ NUP N 140 140 166 172 190 290 290 266 4 4 30.2
B 96 B 97
B084-109E.indd 96-97 11/20/13 4:56:15 PM

B B
r r r r ra rb ra
r1 r1
r1 r1 r r r1 r r
rb ra
NU NJ NUP N NF
(mm) (N) (min 1) (mm) (kg)
(3)
130 200 33 2 1.1 148 182 172 000 238 000 3 200 3 800 NU 1026 NU NJ N NF 139 136.5 146 151 191 193.5 184 2 1 3.66
230 40 3 3 204 270 000 340 000 2 600 3 200 N 226 N NF 143 217 208 2.5 2.5 6.48
230 40 3 3 153.5 365 000 455 000 2 600 3 200 NU 226 EM NU NJ NUP 143 143 150 158 168 217 2.5 2.5 8.03
230 64 3 3 153.5 530 000 735 000 2 400 3 000 NU 2226 EM NU NJ NUP 143 143 150 158 168 217 2.5 2.5 9.44
280 58 4 4 243 500 000 570 000 2 200 2 600 N 326 N NF 146 264 247.5 3 3 17.7
280 58 4 4 167 615 000 735 000 2 200 2 600 NU326EM NU NJ NUP 146 146 163 169 184 264 3 3 18.7
280 93 4 4 167 920 000 1 230 000 1 900 2 400 NU2326EM NU NJ NUP 146 146 163 169 184 264 3 3 30
340 78 5 5 185 285 825 000 955 000 1 800 2 200 NU 426 NU NJ NF 150 150 180 187 208 320 320 291 4 4 39.6
140 210 33 2 1.1 158 192 176 000 250 000 3 000 3 600 NU 1028 NU NJ NUP N 149 146.5 156 161 201 203.5 194 2 1 3.87
250 42 3 3 221 297 000 375 000 2 400 3 000 N 228 N NF 153 237 225 2.5 2.5 8.08
250 42 3 3 169 395 000 515 000 2 400 3 000 NU228EM NU NJ NUP 153 153 165 171 182 237 2.5 2.5 9.38
250 68 3 3 169 550 000 790 000 2 200 2 800 NU2228EM NU NJ NUP 153 153 165 171 182 237 2.5 2.5 15.2
300 62 4 4 260 550 000 640 000 2 000 2 400 N 328 N NF 156 284 266 3 3 21.7
300 62 4 4 180 665 000 795 000 2 000 2 400 NU328EM NU NJ NUP 156 156 176 182 198 284 3 3 22.8
300 102 4 4 180 1 020 000 1 380 000 1 700 2 200 NU2328EM NU NJ NUP 156 156 176 182 198 284 3 3 37.7
360 82 5 5 198 302 875 000 1 020 000 1 700 2 000 NU 428 NU NJ N 160 160 193 200 222 340 340 308 4 4 46.4
150 225 35 2.1 1.5 169.5 205.5 202 000 294 000 2 800 3 400 NU 1030 NU NJ N NF 161 158 167 173 214 217 208 2 1.5 4.77
270 45 3 3 238 360 000 465 000 2 200 2 800 N 230 N NF 163 257 242 2.5 2.5 10.4
270 45 3 3 182 450 000 595 000 2 200 2 800 NU230EM NU NJ NUP 163 163 177 184 196 257 2.5 2.5 11.9
270 73 3 3 182 635 000 930 000 2 000 2 600 NU2230EM NU NJ NUP 163 163 177 184 196 257 2.5 2.5 19.3
320 65 4 4 277 665 000 805 000 1 800 2 200 N 330 N NF 166 304 283 3 3 25.8
320 65 4 4 193 760 000 920 000 1 800 2 200 NU330EM NU NJ NUP 166 166 188 195 213 304 3 3 27.1
320 108 4 4 193 1 160 000 1 600 000 1 600 2 000 NU2330EM NU NJ NUP 166 166 188 195 213 304 3 3 45.1
380 85 5 5 213 930 000 1 120 000 1 600 2 000 NU 430 NU NJ 170 170 208 216 237 360 4 4 55.8
160 240 38 2.1 1.5 180 220 238 000 340 000 2 600 3 200 NU 1032 NU NJ N NF 171 168 178 184 229 232 222 2 1.5 5.81
290 48 3 3 255 430 000 570 000 2 200 2 600 N 232 N NF 173 277 261 2.5 2.5 14.1
290 48 3 3 195 500 000 665 000 2 200 2 600 NU232EM NU NJ NUP 173 173 190 197 210 277 2.5 2.5 14.7
290 80 3 3 193 810 000 1 190 000 1 900 2 400 NU2232EM NU NJ NUP 173 173 188 197 210 277 2.5 2.5 24.5
340 68 4 4 292 700 000 875 000 1 700 2 000 N 332 N 176 324 298 3 3 30.8
340 68 4 4 204 860 000 1 050 000 1 700 2 000 NU332EM NU NJ NUP 176 176 199 211 228 324 3 3 32.1
340 114 4 4 204 1 310 000 1 820 000 1 500 1 900 NU2332EM NU NJ NUP 176 176 199 211 228 324 3 3 53.9
B 98 B 99
B084-109E.indd 98-99 11/20/13 4:56:17 PM

B B
r1 r1 r r r1 r r
rb ra
NU NJ NUP N NF
(mm) (N) (min 1) (mm) (kg)
(1)
170 260 42 2.1 2.1 193 237 287 000 415 000 2 400 2 800 NU 1034 NU NJ N 181 181 190 197 249 249 239 2 2 7.91
310 52 4 4 272 475 000 635 000 2 000 2 400 N 234 N NF 186 294 278 3 3 17.4
310 52 4 4 207 605 000 800 000 2 000 2 400 NU234EM NU NJ NUP 186 186 202 211 223 294 3 3 18.3
310 86 4 4 205 925 000 1 330 000 1 800 2 200 NU2234EM NU NJ NUP 186 186 200 211 223 294 3 3 29.9
360 72 4 4 310 795 000 1 010 000 1 600 2 000 N 334 N 186 344 316 3 3 36.6
360 72 4 4 218 930 000 1 150 000 1 600 2 000 NU334EM NU NJ NUP 186 186 213 223 241 344 3 3 37.9
360 120 4 4 216 1 490 000 2 070 000 1 400 1 800 NU2334EM NU NJ NUP 186 186 210 223 241 344 3 3 63.4
180 280 46 2.1 2.1 205 255 355 000 510 000 2 200 2 600 NU 1036 NU NJ N NF 191 191 202 209 269 269 258 2 2 10.2
320 52 4 4 282 495 000 675 000 1 900 2 200 N 236 N NF 196 304 288 3 3 18.1
320 52 4 4 217 625 000 850 000 1 900 2 200 NU236EM NU NJ NUP 196 196 212 221 233 304 3 3 19
320 86 4 4 215 1 010 000 1 510 000 1 700 2 000 NU2236EM NU NJ NUP 196 196 210 221 233 304 3 3 31.4
380 75 4 4 328 905 000 1 150 000 1 500 1 800 N 336 N NF 196 364 335 3 3 42.6
380 75 4 4 231 985 000 1 230 000 1 500 1 800 NU336EM NU NJ NUP 196 196 226 235 255 364 3 3 44
380 126 4 4 227 1 560 000 2 220 000 1 300 1 700 NU2336EM NU NJ NUP 196 196 222 235 255 364 3 3 74.6
190 290 46 2.1 2.1 215 265 365 000 535 000 2 000 2 600 NU 1038 NU NJ N 201 201 212 219 279 279 268 2 2 10.7
340 55 4 4 299 555 000 770 000 1 800 2 200 N 238 N NF 206 324 305 3 3 22
340 55 4 4 230 695 000 955 000 1 800 2 200 NU238EM NU NJ NUP 206 206 225 234 247 324 3 3 23
340 92 4 4 228 1 100 000 1 670 000 1 600 2 000 NU2238EM NU NJ NUP 206 206 223 234 247 324 3 3 38.3
400 78 5 5 345 975 000 1 260 000 1 400 1 700 N 338 N 210 380 352 4 4 48.7
400 78 5 5 245 1 060 000 1 340 000 1 400 1 700 NU338EM NU NJ NUP 210 210 240 248 268 380 4 4 50.6
400 132 5 5 240 1 770 000 2 520 000 1 300 1 600 NU2338EM NU NJ NUP 210 210 235 248 268 380 4 4 86.2
200 310 51 2.1 2.1 229 281 390 000 580 000 2 000 2 400 NU 1040 NU NJ N NF 211 211 226 233 299 299 284 2 2 14
360 58 4 4 316 620 000 865 000 1 700 2 000 N 240 N NF 216 344 323 3 3 26.2
360 58 4 4 243 765 000 1 060 000 1 700 2 000 NU240EM NU NJ NUP 216 216 238 247 261 344 3 3 27.4
360 98 4 4 241 1 220 000 1 870 000 1 500 1 800 NU2240EM NU NJ NUP 216 216 235 247 261 344 3 3 46.1
420 80 5 5 360 975 000 1 270 000 1 300 1 600 N 340 N NF 220 400 367 4 4 55.3
420 80 5 5 258 1 140 000 1 450 000 1 300 1 600 NU340EM NU NJ NUP 220 220 252 263 283 400 4 4 57.1
420 138 5 5 253 1 910 000 2 760 000 1 200 1 500 NU2340EM NU NJ NUP 220 220 247 263 283 400 4 4 99.3
220 340 56 3 3 250 310 500 000 750 000 1 800 2 200 NU 1044 NU NJ N 233 233 247 254 327 327 313 2.5 2.5 18.2
400 65 4 4 350 760 000 1 080 000 1 500 1 800 N 244 N NF 236 384 357 3 3 37
400 65 4 4 270 760 000 1 080 000 1 500 1 800 NU 244 NU NJ NUP 236 236 264 273 289 384 3 3 37.3
400 108 4 4 270 1 140 000 1 810 000 1 300 1 600 NU 2244 NU 236 264 273 289 384 3 3 61.8
460 88 5 5 396 1 190 000 1 570 000 1 200 1 500 N 344 N 240 440 403 4 4 72.8
460 88 5 5 284 1 190 000 1 570 000 1 200 1 500 NU 344 NU NJ 240 240 278 287 307 440 4 4 74.6
Notes (1) When L-shaped thrust collars (Refer to page B105) are used, the bearings become the NH Type.
(2) If axial loads are applied, increase da and reduce Da from the values listed above.
B 100 B 101
B084-109E.indd 100-101 11/20/13 4:56:19 PM

B B
r1 r1 r r r1 r r
rb ra
NU NJ NUP N NF
(mm) (N) (min 1) (mm) (kg)
(1)
240 360 56 3 3 270 330 530 000 820 000 1 600 2 000 NU 1048 NU NJ N 253 253 266 275 347 347 333 2.5 2.5 19.5
440 72 4 4 385 935 000 1 340 000 1 300 1 600 N 248 N NF 256 424 392 3 3 49.6
440 72 4 4 295 935 000 1 340 000 1 300 1 600 NU 248 NU NJ NUP 256 256 289 298 316 424 3 3 50.4
440 120 4 4 295 1 440 000 2 320 000 1 200 1 500 NU 2248 NU 256 289 298 316 424 3 3 84.9
500 95 5 5 430 1 360 000 1 820 000 1 100 1 300 N 348 N 260 480 438 4 4 92.3
500 95 5 5 310 1 360 000 1 820 000 1 100 1 300 NU 348 NU NJ 260 260 304 313 333 480 4 4 94.6
260 400 65 4 4 296 364 645 000 1 000 000 1 500 1 800 NU 1052 NU NJ N NF 276 276 292 300 384 384 367 3 3 29.1
480 80 5 5 420 1 100 000 1 580 000 1 200 1 500 N 252 N 280 460 428 4 4 66.2
480 80 5 5 320 1 100 000 1 580 000 1 200 1 500 NU 252 NU NJ 280 280 314 323 343 460 4 4 67.1
480 130 5 5 320 1 710 000 2 770 000 1 100 1 300 NU 2252 NU NUP 280 280 314 323 343 460 4 4 111
540 102 6 6 336 1 540 000 2 090 000 1 000 1 200 NU 352 NU NJ 286 286 330 339 359 514 5 5 118
280 420 65 4 4 316 384 660 000 1 050 000 1 400 1 700 NU 1056 NU NJ NUP N NF 296 296 312 320 404 404 387 3 3 30.8
500 80 5 5 440 1 140 000 1 680 000 1 100 1 400 N 256 N NF 300 480 448 4 4 69.6
500 80 5 5 340 1 140 000 1 680 000 1 100 1 400 NU 256 NU NJ 300 300 334 344 364 480 4 4 70.7
300 460 74 4 4 340 420 885 000 1 400 000 1 300 1 500 NU 1060 NU NJ N NF 316 316 336 344 444 444 424 3 3 43.7
540 85 5 5 364 1 400 000 2 070 000 1 100 1 300 NU 260 NU NJ 320 320 358 368 391 520 4 4 89.2
320 480 74 4 4 360 440 905 000 1 470 000 1 200 1 400 NU 1064 NU N NF 336 336 356 365 464 464 444 3 3 46.1
580 92 5 5 510 1 540 000 2 270 000 950 1 200 N 264 N 340 560 519 4 4 110
580 92 5 5 390 1 540 000 2 270 000 950 1 200 NU 264 NU NJ 340 340 384 394 420 560 4 4 112
340 520 82 5 5 385 475 1 080 000 1 740 000 1 100 1 300 NU 1068 NU NJ N NF 360 360 381 390 500 500 479 4 4 61.8
360 540 82 5 5 405 495 1 110 000 1 830 000 1 000 1 300 NU 1072 NU N NF 380 380 400 410 520 520 499 4 4 64.6
380 560 82 5 5 425 1 140 000 1 910 000 1 000 1 200 NU 1076 NU 400 420 430 540 4 4 67.5
400 600 90 5 5 450 550 1 360 000 2 280 000 900 1 100 NU 1080 NU NUP N 420 420 445 455 580 580 554.5 4 4 88.2
420 620 90 5 5 470 570 1 390 000 2 380 000 850 1 100 NU 1084 NU N 440 440 465 475 600 600 574.5 4 4 91.7
440 650 94 6 6 493 1 470 000 2 530 000 800 1 000 NU 1088 NU 466 488 498 624 5 5 105
460 680 100 6 6 516 624 1 580 000 2 740 000 750 950 NU 1092 NU NUP N 486 486 511 521 654 654 628.5 5 5 123
480 700 100 6 6 536 644 1 620 000 2 860 000 750 900 NU 1096 NU NJ N 506 506 531 541 674 674 654 5 5 127
500 720 100 6 6 556 664 1 660 000 2 970 000 710 850 NU10/500 NU N 526 526 551 558 694 694 674 5 5 131
Notes (1) When L-shaped thrust collars (Refer to page B105) are used, the bearings become the NH Type.
(2) If axial loads are applied, increase da and reduce Da from the values listed above.
B 102 B 103
B084-109E.indd 102-103 11/20/13 4:56:21 PM

L-Shaped Thrust Collars
Bore Diameter 20 85 mm Bore Diameter 90 320 mm
r1 B1 r1 B1
jd1 jd jd1 jd
B2 B2
L-Shaped Thrust Collar L-Shaped Thrust Collar
Boundary Dimensions Mass Boundary Dimensions Mass Boundary Dimensions Mass Boundary Dimensions Mass
(mm) (kg) (mm) (kg) (mm) (kg) (mm) (kg)
Bearing Bearing Bearing Bearing
Numbers Numbers Numbers Numbers
d d1 B1 B2 r1 d d1 B1 B2 r1 d d1 B1 B2 r1 d d1 B1 B2 r1
min. approx. min. approx. min. approx. min. approx.
20 30 3 6.75 0.6 HJ 204 0.012 55 70.9 6 9.5 1.1 HJ 211 E 0.087 90 114.3 9 14 2 HJ 218 E 0.32 150 193.7 12 19.5 3 HJ 230 E 1.26
29.8 3 5.5 0.6 HJ 204 E 0.011 70.9 6 10 1.1 HJ 2211 E 0.088 114.3 9 15 2 HJ 2218 E 0.325 193.7 12 24.5 3 HJ 2230 E 1.35
30 3 7.5 0.6 HJ 2204 0.012 77.6 9 14 2 HJ 311 E 0.195 124.2 12 18.5 3 HJ 318 E 0.63 210 15 25 4 HJ 330 E 2.35
29.8 3 6.5 0.6 HJ 2204 E 0.012 77.6 9 15.5 2 HJ 2311 E 0.20 124.2 12 22 3 HJ 2318 E 0.66
31.7 4 7.5 0.6 HJ 304 0.017 210 15 31.5 4 HJ 2330 E 2.48
85.2 10 16.5 2.1 HJ 411 0.29 137 14 24 4 HJ 418 1.05 234 20 36.5 5 HJ 430 4.7
31.4 4 6.5 0.6 HJ 304 E 0.017
60 77.7 6 10 1.5 HJ 212 E 0.108 95 120.6 9 14 2.1 HJ 219 E 0.355
31.8 4 8.5 0.6 HJ 2304 0.017 120.6 9 15.5 2.1 HJ 2219 E 0.365 160 207.3 12 20 3 HJ 232 E 1.48
31.4 4 7.5 0.6 HJ 2304 E 0.018 77.7 6 10 1.5 HJ 2212 E 0.108 206.1 12 24.5 3 HJ 2232 E 1.55
84.5 9 14.5 2.1 HJ 312 E 0.231 132.2 13 20.5 3 HJ 319 E 0.785
25 34.8 3 6 0.6 HJ 205 E 0.014 222 15 25 4 HJ 332 E 2.59
132.2 13 24.5 3 HJ 2319 E 0.815 222.1 15 32 4 HJ 2332 E 2.76
34.8 3 6.5 0.6 HJ 2205 E 0.014 84.5 9 16 2.1 HJ 2312 E 0.237
147 15 25.5 4 HJ 419 1.3
38.2 4 7 1.1 HJ 305 E 0.025 91.8 10 16.5 2.1 HJ 412 0.34 170 220.8 12 20 4 HJ 234 E 1.7
100 127.5 10 15 2.1 HJ 220 E 0.44
38.2 4 8 1.1 HJ 2305 E 0.026 65 84.5 6 10 1.5 HJ 213 E 0.129 127.5 10 16 2.1 HJ 2220 E 0.45 219.5 12 24 4 HJ 2234 E 1.79
43.6 6 10.5 1.5 HJ 405 0.057 84.5 6 10.5 1.5 HJ 2213 E 0.131 139.6 13 20.5 3 HJ 320 E 0.89 238 16 33.5 4 HJ 2334 E 3.25
30 41.3 4 7 0.6 HJ 206 E 0.025 90.6 10 15.5 2.1 HJ 313 E 0.288
139.6 13 23.5 3 HJ 2320 E 0.92 180 230.8 12 20 4 HJ 236 E 1.79
41.4 4 7.5 0.6 HJ 2206 E 0.025 90.6 10 18 2.1 HJ 2313 E 0.298 153.5 16 27 4 HJ 420 1.5 229.5 12 24 4 HJ 2236 E 1.88
45.1 5 8.5 1.1 HJ 306 E 0.042 98.5 11 18 2.1 HJ 413 0.42 252 17 35 4 HJ 2336 E 3.85
105 145 13 20.5 3 HJ 321 E 0.97
45.1 5 9.5 1.1 HJ 2306 E 0.043 159.5 16 27 4 HJ 421 1.65
50.5 7 11.5 1.5 HJ 406 0.080 70 89.5 7 11 1.5 HJ 214 E 0.157 190 244.5 13 21.5 4 HJ 238 E 2.19
89.5 7 11.5 1.5 HJ 2214 E 0.158 110 141.7 11 17 2.1 HJ 222 E 0.62 243.2 13 26.5 4 HJ 2238 E 2.31
35 48.2 4 7 0.6 HJ 207 E 0.033 97.5 10 15.5 2.1 HJ 314 E 0.33 260.6 18 36.5 5 HJ 2338 E 4.45
141.7 11 19.5 2.1 HJ 2222 E 0.645
48.2 4 8.5 0.6 HJ 2207 E 0.035
97.5 10 18.5 2.1 HJ 2314 E 0.345 155.8 14 22 3 HJ 322 E 1.21
51.1 6 9.5 1.1 HJ 307 E 0.060 200 258.2 14 23 4 HJ 240 E 2.65
110.5 12 20 3 HJ 414 0.605 155.8 14 26.5 3 HJ 2322 E 1.27 258 14 34 4 HJ 2240 2.6
51.1 6 11 1.1 HJ 2307 E 0.062
59 8 13 1.5 HJ 407 0.12 75 94.5 7 11 1.5 HJ 215 E 0.166 171 17 29.5 4 HJ 422 2.1 256.9 14 28 4 HJ 2240 E 2.78
94.5 7 11.5 1.5 HJ 2215 E 0.167 120 153.4 11 17 2.1 HJ 224 E 0.71 280 18 30 5 HJ 340 E 5.0
40 54.1 5 8.5 1.1 HJ 208 E 0.049
54.1 5 9 1.1 HJ 2208 E 0.050 104.2 11 16.5 2.1 HJ 315 E 0.41 153.4 11 20 2.1 HJ 2224 E 0.745 220 286 15 27.5 4 HJ 244 3.55
57.6 7 11 1.5 HJ 308 E 0.088 168.6 14 22.5 3 HJ 324 E 1.41 286 15 36.5 4 HJ 2244 3.55
104.2 11 19.5 2.1 HJ 2315 E 0.43
57.7 7 12.5 1.5 HJ 2308 E 0.091 116 13 21.5 3 HJ 415 0.71 168.6 14 26 3 HJ 2324 E 1.46 307 20 36 5 HJ 344 7.05
64.8 8 13 2 HJ 408 0.14 188 17 30.5 5 HJ 424 2.6
80 101.6 8 12.5 2 HJ 216 E 0.222 240 313 16 29.5 4 HJ 248 4.65
45 59.1 5 8.5 1.1 HJ 209 E 0.055 101.6 8 12.5 2 HJ 2216 E 0.222 130 164.2 11 17 3 HJ 226 E 0.79 313 16 38.5 4 HJ 2248 4.65
59.1 5 9 1.1 HJ 2209 E 0.055 110.6 11 17 2.1 HJ 316 E 0.46 164.2 11 21 3 HJ 2226 E 0.84 334 22 39.5 5 HJ 348 8.2
64.5 7 11.5 1.5 HJ 309 E 0.11 182.3 14 23 4 HJ 326 E 1.65
110.6 11 20 2.1 HJ 2316 E 0.48 182.3 14 28 4 HJ 2326 E 1.73 260 340 18 33 5 HJ 252 6.2
64.5 7 13 1.5 HJ 2309 E 0.113 122 13 22 3 HJ 416 0.78 340 18 40.5 5 HJ 2252 6.2
71.7 8 13.5 2 HJ 409 0.175 205 18 32 5 HJ 426 3.3
362 24 43 6 HJ 352 11.4
50 64.1 5 9 1.1 HJ 210 E 0.061 85 107.6 8 12.5 2 HJ 217 E 0.25 140 180 11 18 3 HJ 228 E 0.99
64.1 5 9 1.1 HJ 2210 E 0.061 107.6 8 13 2 HJ 2217 E 0.252 180 11 23 3 HJ 2228 E 1.07 280 360 18 33 5 HJ 256 7.4
71.4 8 13 2 HJ 310 E 0.151 117.9 12 18.5 3 HJ 317 E 0.575 196 15 25 4 HJ 328 E 2.04
300 387 20 34.5 5 HJ 260 9.15
71.4 8 14.5 2 HJ 2310 E 0.155 117.9 12 22 3 HJ 2317 E 0.595 196 15 31 4 HJ 2328 E 2.14
78.8 9 14.5 2.1 HJ 410 0.23 126 14 24 4 HJ 417 0.88 219 18 33 5 HJ 428 3.75 320 415 21 37 5 HJ 264 11.3
B 104 B 105
B084-109E.indd 104-105 11/20/13 4:56:23 PM

DOUBLE-ROW CYLINDRICAL ROLLER BEARINGS
B B B B ra ra
r r r r
r ra
r
jDa jda jda jdc jd a jd 1a jDa

jD jEw jd jD jEw jd jD jd jF w jD jd jF w
NN NN NNU NNU
Cylindrical Bore Tapered Bore Cylindrical Bore Tapered Bore
(mm) (N) (min 1) (mm) (kg)
d D B r FW EW Cr C 0r Grease Oil Cylindrical Bore Tapered Bore(1) da(2) d 1a dc Da ra

min. min. max. min. min. max. min. max. approx.
25 47 16 0.6 41.3 25 800 30 000 14 000 17 000 NN 3005 NN 3005 K 29 29 43 42 0.6 0.127
30 55 19 1 48.5 31 000 37 000 12 000 14 000 NN 3006 NN 3006 K 35 36 50 50 1 0.198
35 62 20 1 55 39 500 50 000 10 000 12 000 NN 3007 NN 3007 K 40 41 57 56 1 0.258
40 68 21 1 61 43 500 55 500 9 000 11 000 NN 3008 NN 3008 K 45 46 63 62 1 0.309
45 75 23 1 67.5 52 000 68 500 8 500 10 000 NN 3009 NN 3009 K 50 51 70 69 1 0.407
50 80 23 1 72.5 53 000 72 500 7 500 9 000 NN 3010 NN 3010 K 55 56 75 74 1 0.436
55 90 26 1.1 81 69 500 96 500 6 700 8 000 NN 3011 NN 3011 K 61.5 62 83.5 83 1 0.647
60 95 26 1.1 86.1 73 500 106 000 6 300 7 500 NN 3012 NN 3012 K 66.5 67 88.5 88 1 0.693
65 100 26 1.1 91 77 000 116 000 6 000 7 100 NN 3013 NN 3013 K 71.5 72 93.5 93 1 0.741
70 110 30 1.1 100 97 500 148 000 5 600 6 700 NN 3014 NN 3014 K 76.5 77 103.5 102 1 1.06
75 115 30 1.1 105 96 500 149 000 5 300 6 300 NN 3015 NN 3015 K 81.5 82 108.5 107 1 1.11
80 125 34 1.1 113 119 000 186 000 4 800 6 000 NN 3016 NN 3016 K 86.5 87 118.5 115 1 1.54
85 130 34 1.1 118 125 000 201 000 4 500 5 600 NN 3017 NN 3017 K 91.5 92 123.5 120 1 1.63
90 140 37 1.5 127 143 000 228 000 4 300 5 000 NN 3018 NN 3018 K 98 99 132 129 1.5 2.09
95 145 37 1.5 132 150 000 246 000 4 000 5 000 NN 3019 NN 3019 K 103 104 137 134 1.5 2.19
100 140 40 1.1 112 155 000 295 000 4 000 5 000 NNU 4920 NNU 4920 K 106.5 111 108 115 133.5 1 1.9
150 37 1.5 137 157 000 265 000 4 000 4 800 NN 3020 NN 3020 K 108 109 142 139 1.5 2.28
105 145 40 1.1 117 161 000 315 000 3 800 4 800 NNU 4921 NNU 4921 K 111.5 116 113 120 138.5 1 1.99
160 41 2 146 198 000 320 000 3 800 4 500 NN 3021 NN 3021 K 114 115 151 148 2 2.88
110 150 40 1.1 122 167 000 335 000 3 600 4 500 NNU 4922 NNU 4922 K 116.5 121 118 125 143.5 1 2.07
170 45 2 155 229 000 375 000 3 400 4 300 NN 3022 NN 3022 K 119 121 161 157 2 3.71
120 165 45 1.1 133.5 183 000 360 000 3 200 4 000 NNU 4924 NNU 4924 K 126.5 133 128 137 158.5 1 2.85
180 46 2 165 239 000 405 000 3 200 3 800 NN 3024 NN 3024 K 129 131 171 167 2 4.04
130 180 50 1.5 144 274 000 545 000 3 000 3 800 NNU 4926 NNU 4926 K 138 143 140 148 172 1.5 3.85
200 52 2 182 284 000 475 000 3 000 3 600 NN 3026 NN 3026 K 139 141 191 185 2 5.88
140 190 50 1.5 154 283 000 585 000 2 800 3 600 NNU 4928 NNU 4928 K 148 153 150 158 182 1.5 4.08
210 53 2 192 298 000 515 000 2 800 3 400 NN 3028 NN 3028 K 149 151 201 195 2 6.34
Note (1) The suffix K represents bearings with tapered bores (taper 1 : 12). Note (2) da (max.) are values for adjusting rings for the NNU Type.
Remarks Production of double-row cylindrical roller bearings is generally in the high precision classes (Class 5 or better).
B 106 B 107
B084-109E.indd 106-107 11/20/13 4:56:24 PM

DOUBLE-ROW CYLINDRICAL ROLLER BEARINGS
B B B B ra ra
r r r r
r ra
r
jDa jda jda jdc jd a jd 1a jDa

jD jEw jd jD jEw jd jD jd jF w jD jd jF w
NN NN NNU NNU
Cylindrical Bore Tapered Bore Cylindrical Bore Tapered Bore
(mm) (N) (min 1) (mm) (kg)
d D B r FW EW Cr C 0r Grease Oil Cylindrical Bore Tapered Bore(1) da(2) d 1a dc Da ra

min. min. max. min. min. max. min. max. approx.
150 210 60 2 167 350 000 715 000 2 600 3 200 NNU 4930 NNU 4930 K 159 166 162 171 201 2 6.39
225 56 2.1 206 335 000 585 000 2 600 3 000 NN 3030 NN 3030 K 161 162 214 209 2 7.77
160 220 60 2 177 365 000 760 000 2 400 3 000 NNU 4932 NNU 4932 K 169 176 172 182 211 2 6.76
240 60 2.1 219 375 000 660 000 2 400 2 800 NN 3032 NN 3032 K 171 172 229 222 2 9.41
170 230 60 2 187 375 000 805 000 2 400 2 800 NNU 4934 NNU 4934 K 179 186 182 192 221 2 7.12
260 67 2.1 236 450 000 805 000 2 200 2 600 NN 3034 NN 3034 K 181 183 249 239 2 12.8
180 250 69 2 200 480 000 1 020 000 2 200 2 600 NNU 4936 NNU 4936 K 189 199 193 205 241 2 10.4
280 74 2.1 255 565 000 995 000 2 000 2 400 NN 3036 NN 3036 K 191 193 269 258 2 16.8
190 260 69 2 211.5 485 000 1 060 000 2 000 2 600 NNU 4938 NNU 4938 K 199 211 203 217 251 2 10.9
290 75 2.1 265 595 000 1 080 000 2 000 2 400 NN 3038 NN 3038 K 201 203 279 268 2 17.8
200 280 80 2.1 223 570 000 1 220 000 1 900 2 400 NNU 4940 NNU 4940 K 211 222 214 228 269 2 15.3
310 82 2.1 282 655 000 1 170 000 1 800 2 200 NN 3040 NN 3040 K 211 214 299 285 2 22.7
220 300 80 2.1 243 600 000 1 330 000 1 700 2 200 NNU 4944 NNU 4944 K 231 242 234 248 289 2 16.6
340 90 3 310 815 000 1 480 000 1 700 2 000 NN 3044 NN 3044 K 233 236 327 313 2.5 29.6
240 320 80 2.1 263 625 000 1 450 000 1 600 2 000 NNU 4948 NNU 4948 K 251 262 254 269 309 2 18
360 92 3 330 855 000 1 600 000 1 500 1 800 NN 3048 NN 3048 K 253 256 347 334 2.5 32.7
260 360 100 2.1 289 935 000 2 100 000 1 400 1 800 NNU 4952 NNU 4952 K 271 288 275 295 349 2 31.1
400 104 4 364 1 030 000 1 920 000 1 400 1 700 NN 3052 NN 3052 K 276 278 384 368 3 47.7
280 380 100 2.1 309 960 000 2 230 000 1 300 1 700 NNU 4956 NNU 4956 K 291 308 295 315 369 2 33
420 106 4 384 1 080 000 2 080 000 1 300 1 500 NN 3056 NN 3056 K 296 298 404 388 3 51.1
300 420 118 3 336 1 230 000 2 870 000 1 200 1 500 NNU 4960 NNU 4960 K 313 335 318 343 407 2.5 51.9
460 118 4 418 1 290 000 2 460 000 1 200 1 400 NN 3060 NN 3060 K 316 319 444 422 3 70.7
320 440 118 3 356 1 260 000 3 050 000 1 100 1 400 NNU 4964 NNU 4964 K 333 355 338 363 427 2.5 54.9
480 121 4 438 1 350 000 2 670 000 1 100 1 300 NN 3064 NN 3064 K 336 340 464 442 3 76.6
340 520 133 5 473 1 670 000 3 300 000 1 000 1 200 NN 3068 NN 3068 K 360 365 500 477 4 102
360 540 134 5 493 1 700 000 3 450 000 950 1 200 NN 3072 NN 3072 K 380 385 520 497 4 106
Note (1) The suffix K represents bearings with tapered bores (taper 1 : 12). Note (2) da (max.) are values for adjusting rings for the NNU Type.
Remarks Production of double-row cylindrical roller bearings is generally in the high precision classes (Class 5 or better).
B 108 B 109
B084-109E.indd 108-109 11/20/13 4:56:25 PM

TAPERED ROLLER BEARINGS
METRIC DESIGN TAPERED ROLLER BEARINGS
INCH DESIGN TAPERED ROLLER BEARINGS
Bore Diameter 12.000 47.625mm B136
The index for inch design tapered roller bearings is in Appendix 14 (Page C26).
DOUBLE-ROW TAPERED ROLLER BEARINGS
Four-Row Tapered Roller Bearings are described on pages B334 to B339.

Tapered roller bearings are designed so the apices of the cones formed
by the raceways of the cone and cup and the conical rollers all coincide at
one point on the axis of the bearing. When a radial load is imposed, an axial
force component occurs; therefore, it is necessary to use two bearings in
Contact opposition or some other multiple arrangement.
angle For metric-design medium-angle and steep-angle tapered roller bearings,
the respective contact angle symbol C or D is added after the bore number.
For normal-angle tapered roller bearings, no contact angle symbol is used.
Medium-angle tapered roller bearings are primarily used for the pinion
shafts of differential gears of automobiles.
Among those with high load capacity(HR series), some bearings have the
basic number suffixed by J to conform to the specifications of ISO for the
cup back face raceway diameter, cup width, and contact angle. Therefore,
the cone assembly and cup of bearings with the same basic number suffixed
by J are internationally interchangeable.
Among metric-design tapered roller bearings specified by ISO 355, there
are those having new dimensions that are different than the dimension
series 3XX used in the past. Part of them are listed in the bearing tables.
They conform to the specifications of ISO for the smaller end diameter of
the cup and contact angle. The cone and cup assemblies are internationally
interchangeable. The bearing number formulation, which is different than
that for past metric design, is as follows:
Example: T 7 F C 045

Symbol Representing Diameter Width Bore

Contact Angle
Tapered Roller Symbol Symbol Diameter
Bearings 14444444244444443 Symbol
New Series Symbols of ISO (Bore diameter
in mm)
B 110 B 111
B110-181E.indd 110-111 11/20/13 4:56:52 PM

Besides metric design tapered roller bearings, there are also inch design TOLERANCES AND RUNNING ACCURACY
bearings. For the cone assemblies and cups of inch design bearings, except
four-row tapered roller bearings, the bearing numbers are approximately METRIC DESIGN TAPERED ROLLER
formulated as follows: BEARINGS Table 8.3 (Pages A64 to A67)
INCH DESIGN TAPERED ROLLER
Example: LM
1
19
49
BEARINGS Table 8.4 (Pages A68 and A69)
Among inch design tapered roller bearings, there are those to which the
Load Limit Contact Angle Additional following precision classes apply. For more details, please consult with NSK.
Series No. Design No.
Symbol Symbol Symbol
(1) J line bearings(in the bearing tables, bearings preceeded by )
For tapered roller bearings, besides single-row bearings, there are also
various combinations of bearings. Table 2 Tolerances for Cones(CLASS K)
The cages of tapered roller bearings are usually pressed steel. Units : m
d & d mp Vdp V d mp K ia
(mm)
Table 1 Design and Featured of Combinations of Tapered Roller Bearings
over incl. high low max. max. max.
Figure Arrangement Examples of Bearing No. Features
10 18 0 12 12 9 15
Two standard bearings are combined. The bearing clearances 18 30 0 12 12 9 18
Back-to-back HR30210JDB+KLR10 30 50 0 12 12 9 20
are adjusted by cone spacers or cup spacers. The cones
and cups and spacers are marked with serial numbers and 50 80 0 15 15 11 25
mating marks. Components with the same serial number can 80 120 0 20 20 15 30
Face-to-face HR30210JDF+KR 120 180 0 25 25 19 35
be assembled referring to the matching symbols.
180 250 0 30 30 23 50
250 315 0 35 35 26 60
The KBE type is a back-to-back arrangement of bearings with 315 400 0 40 40 30 70
KBE Type 100KBE31+L the cup and spacer integrated, and the KH type is a face-to-
face arrangement in which the cones are integrated. Since the
bearing clearance is adjusted using spacers, it is necessary
for components to have the same serial number for assembly Table 3 Tolerances for Cups(CALSS K)
KH Type 110KH31+K
with reference to matching symbols.
Units : m
Nominal Outside
Diameter & D mp V Dp V D mp K ea
D (mm)
over incl. high low max. max. max.

18 30 0 12 12 9 18
30 50 0 14 14 11 20
50 80 0 16 16 12 25
80 120 0 18 18 14 35
120 150 0 20 20 15 40
150 180 0 25 25 19 45
180 250 0 30 30 23 50
250 315 0 35 35 26 60
315 400 0 40 40 30 70
400 500 0 45 45 34 80
B 112 B 113
B110-181E.indd 112-113 11/20/13 4:56:53 PM

Table 4 Tolerances for Effective Widths of Cone Assemblies and
Cups, and Overall Width (CLASS K) INTERNAL CLEARANCE
Units : m METRIC DESIGN TAPERED ROLLER BEARINGS
Nominal Bore Diameter Effective Width Deviation Effective Width Overall (Matched and Double-Row) Table 9.16 (Page A93)
d of Cone Assembly Deviation of Cup Width Deviation INCH DESIGN TAPERED ROLLER BEARINGS
(mm) & T 1s & T 2s & Ts
(Matched and Double-Row) Table 9.16 (Page A93)
over incl. high low high low high low
10 80 + 100 0 + 100 0 + 200 0

DIMENSIONS RELATED TO MOUNTING
80 120 + 100 100 + 100 100 + 200 200 The dimensions related to mounting tapered roller bearings are listed in the
120 315 + 150 150 + 200 100 + 350 250 bearing tables. Since the cages protrude from the ring faces of tapered roller
315 400 + 200 200 + 200 200 + 400 400 bearings, please use care when designing shafts and housings.
When heavy axial loads are imposed, the shaft shoulder dimensions and
(2) Bearings for Front Axles of Automobiles strength must be sufficient to support the cone rib.
(In the bearing tables, those preceded by t)
Table 5 Tolerances for Bore Diameter and Overall Width PERMISSIBLE MISALIGNMENT
Units : m
The permissible misalignment angle for tapered roller bearings is
Nominal Bore Diameter Bore Diameter Overall Width approximately 0.0009 radian (3).
Deviation Deviation
d & ds & Ts
over incl.
(mm) 1/25.4 (mm) 1/25.4
high low high low LIMITING SPEEDS
76.200 3.0000 + 20 0 + 356 0 The limiting speeds listed in the bearing tables should be adjusted
depending on the bearing load conditions. Also, higher speeds are attainable
by making changes in the lubrication method, cage design, etc. Refer to Page
The tolerances for outside diameter and those for radial runout of the cones A37 for detailed information.
and cups conform to Table 8.4.2 (Pages A68 and A69).
(3) Special Chamfer Dimensions PRECAUTIONS FOR USE OF TAPERED ROLLER BEARINGS
For bearings marked spec. in the column of r in the bearing tables, the chamfer 1. If the load on tapered roller bearings becomes too small, or if the ratio of
dimension of the cone back-face side is as shown on the following figure. the axial and radial loads for matched bearings exceeds e(e is listed in the
bearing tables)during operation, slippage between the rollers and raceways
occurs, which may result in smearing. Especially with large bearings since
the weight of the rollers and cage is high. If such load conditions are
expected, please contact NSK for selection of the bearings.
3.56
2. Confirm the dimension of Abutment and Fillet Dimensions of Da, Db, Sa,
Sb at the time of the HR series adoption.
4.75 (min. mm)
RECOMMENDED FITS
METRIC DESIGN TAPERED ROLLER
BEARINGS Table 9.2 (Page A84)
INCH DESIGN TAPERED ROLLER BEARINGS Table 9.6 (Page A86)

B 114 B 115
B110-181E.indd 114-115 11/20/13 4:56:54 PM

SINGLE-ROW TAPERED ROLLER BEARINGS
T Sa Sb
C
r ra Dynamic Equivalent Load
P = X Fr +Y Fa
Fa/ Fre Fa/ Fr>e
ra
r X Y X Y
B
jD jd jDajdb jda jD b 1 0 0.4 Y1
P0 = 0.5Fr +Y0 Fa
When Fr >0.5Fr +Y0 Fa , use P0 = Fr
The values of e, Y1 , and Y0 are
given in the table below.
a
Boundary Dimensions Basic Load Ratings Limiting Speeds Abutment and Fillet Dimensions Eff. Load Constant Axial Load Mass
(mm) (N) {kgf} (min1) ISO355 (mm) Centers Factors (kg)
Cone Cup Bearing Numbers Dimension Cone Cup (mm)
d D T B C r Cr C 0r Cr C 0r Grease Oil Series da db Da Db Sa Sb ra a e Y1 Y0
min. approx. min. max. max. min. min. min. min. max. approx.
15 35 11.75 11 10 0.6 0.6 14 800 13 200 1 510 1 350 11 000 15 000 30202 23 19 30 30 33 2 1.5 0.6 0.6 8.2 0.32 1.9 1.0 0.053
42 14.25 13 11 1 1 23 600 21 100 2 400 2 160 9 500 13 000 HR 30302 J 2FB 24 22 36 36 38.5 2 3 1 1 9.5 0.29 2.1 1.2 0.098
17 40 13.25 12 11 1 1 20 100 19 900 2 050 2 030 9 500 13 000 HR 30203 J 2DB 26 23 34 34 37.5 2 2 1 1 9.7 0.35 1.7 0.96 0.079
40 17.25 16 14 1 1 27 100 28 000 2 770 2 860 9 500 13 000 HR 32203 J 2DD 26 22 34 34 37 2 3 1 1 11.2 0.31 1.9 1.1 0.103
47 15.25 14 12 1 1 29 200 26 700 2 980 2 720 8 500 12 000 HR 30303 J 2FB 26 24 41 40 43 2 3 1 1 10.4 0.29 2.1 1.2 0.134
47 15.25 14 10.5 1 1 22 000 20 300 2 240 2 070 8 000 11 000 30303 D 29 23 41 34 44 2 4.5 1 1 15.4 0.81 0.74 0.41 0.129
47 20.25 19 16 1 1 37 500 36 500 3 800 3 750 8 500 11 000 HR 32303 J 2FD 28 23 41 39 43 2 4 1 1 12.5 0.29 2.1 1.2 0.178
20 42 15 15 12 0.6 0.6 24 600 27 400 2 510 2 800 9 000 12 000 HR 32004 XJ 3CC 28 24 37 35 40 3 3 0.6 0.6 10.6 0.37 1.6 0.88 0.097
47 15.25 14 12 1 1 27 900 28 500 2 850 2 900 8 000 11 000 HR 30204 J 2DB 29 27 41 40 44 2 3 1 1 11.0 0.35 1.7 0.96 0.127
47 15.25 14 12 0.3 1 23 900 24 000 2 430 2 450 8 000 11 000 HR 30204 C-A- 29 26 41 37 44 2 3 0.3 1 13.0 0.55 1.1 0.60 0.126
47 19.25 18 15 1 1 35 500 37 500 3 650 3 850 8 500 11 000 HR 32204 J 2DD 29 25 41 38 44.5 3 4 1 1 12.6 0.33 1.8 1.0 0.161
47 19.25 18 15 1 1 31 500 33 500 3 200 3 400 8 000 11 000 HR 32204 CJ 5DD 29 25 41 36 44 2 4 1 1 14.5 0.52 1.2 0.64 0.166
52 16.25 15 13 1.5 1.5 35 000 33 500 3 550 3 400 7 500 10 000 HR 30304 J 2FB 31 27 44 44 47.5 2 3 1.5 1.5 11.6 0.30 2.0 1.1 0.172
52 16.25 15 12 1.5 1.5 25 300 24 500 2 580 2 490 7 100 10 000 30304 D 34 26 43 37 49 2 4 1.5 1.5 16.7 0.81 0.74 0.41 0.168
52 22.25 21 18 1.5 1.5 45 500 47 500 4 650 4 850 8 000 11 000 HR 32304 J 2FD 33 26 43 42 48 3 4 1.5 1.5 13.9 0.30 2.0 1.1 0.241
22 44 15 15 11.5 0.6 0.6 25 600 29 400 2 610 3 000 8 500 11 000 HR 320/22 XJ 3CC 30 27 39 37 42 3 3.5 0.6 0.6 11.1 0.40 1.5 0.83 0.103
50 15.25 14 12 1 1 29 200 30 500 2 980 3 150 7 500 10 000 HR 302/22 31 29 44 42 47 2 3 1 1 11.6 0.37 1.6 0.90 0.139
50 15.25 14 12 1 1 27 200 29 500 2 780 3 000 7 500 10 000 HR 302/22 C 31 29 44 40 47 2 3 1 1 13.0 0.49 1.2 0.67 0.144
50 19.25 18 15 1 1 36 500 40 500 3 750 4 100 7 500 11 000 HR 322/22 31 28 44 41 47 2 4 1 1 13.5 0.37 1.6 0.89 0.18
50 19.25 18 15 1 1 33 500 39 500 3 400 4 000 7 500 10 000 HR 322/22 C 31 29 44 39 48 2 4 1 1 15.2 0.51 1.2 0.65 0.185
56 17.25 16 14 1.5 1.5 37 000 36 500 3 750 3 750 7 100 9 500 HR 303/22 33 30 47 46 50 2 3 1.5 1.5 12.4 0.32 1.9 1.0 0.208
56 17.25 16 13 1.5 1.5 34 500 34 000 3 500 3 500 6 700 9 500 HR 303/22 C 33 30 47 44 52.5 3 4 1.5 1.5 15.9 0.59 1.0 0.56 0.207
25 47 15 15 11.5 0.6 0.6 27 400 33 000 2 800 3 400 8 000 11 000 HR 32005 XJ 4CC 33 30 42 40 45 3 3.5 0.6 0.6 11.8 0.43 1.4 0.77 0.116
47 17 17 14 0.6 0.6 31 000 38 000 3 150 3 900 8 000 11 000 HR 33005 J 2CE 33 29 42 41 44 3 3 0.6 0.6 11.0 0.29 2.1 1.1 0.131
52 16.25 15 13 1 1 32 000 35 000 3 300 3 550 7 100 10 000 HR 30205 J 3CC 34 31 46 44 48.5 2 3 1 1 12.7 0.37 1.6 0.88 0.157
52 16.25 15 12 1 1 28 100 31 500 2 860 3 200 9 700 9 500 HR 30205 C 34 32 46 43 49.5 2 4 1 1 14.4 0.53 1.1 0.62 0.155
52 19.25 18 16 1 1 40 000 45 000 4 050 4 600 7 100 10 000 HR 32205 J 2CD 34 30 46 44 50 2 3 1 1 13.5 0.36 1.7 0.92 0.189
52 19.25 18 15 1 1 35 000 42 000 3 550 4 250 7 100 9 500 HR 32205 C 34 30 46 40 50 2 4 1 1 15.8 0.53 1.1 0.62 0.19
52 22 22 18 1 1 47 500 56 500 4 850 5 750 7 500 10 000 HR 33205 J 2DE 34 29 46 43 49.5 4 4 1 1 14.1 0.35 1.7 0.94 0.221
62 18.25 17 15 1.5 1.5 47 500 46 000 4 850 4 700 6 300 8 500 HR 30305 J 2FB 36 34 54 54 57 2 3 1.5 1.5 13.2 0.30 2.0 1.1 0.27
62 18.25 17 14 1.5 1.5 42 000 45 000 4 300 4 550 6 000 8 500 HR 30305 C 36 35 53 49 58.5 3 4 1.5 1.5 16.4 0.55 1.1 0.60 0.276
62 18.25 17 13 1.5 1.5 38 000 40 500 3 900 4 100 5 600 8 000 HR 30305 DJ (7FB) 39 34 53 47 59 2 5 1.5 1.5 19.9 0.83 0.73 0.40 0.265
62 18.25 17 13 1.5 1.5 38 000 40 500 3 900 4 100 5 600 8 000 HR 31305 J 7FB 39 33 53 47 59 3 5 1.5 1.5 19.9 0.83 0.73 0.40 0.265
62 25.25 24 20 1.5 1.5 62 500 66 000 6 400 6 750 6 300 8 500 HR 32305 J 2FD 38 32 53 51 57 3 5 1.5 1.5 15.6 0.30 2.0 1.1 0.376
28 52 16 16 12 1 1 32 000 39 000 3 300 3 950 7 100 9 500 HR 320/28 XJ 4CC 37 33 46 44 50 3 4 1 1 12.8 0.43 1.4 0.77 0.146
58 17.25 16 14 1 1 39 500 41 500 4 050 4 200 6 300 9 000 HR 302/28 37 34 52 50 55 2 3 1 1 13.2 0.35 1.7 0.93 0.203
58 17.25 16 12 1 1 34 000 38 500 3 450 3 900 6 300 8 500 HR 302/28 C 37 34 52 48 54 2 5 1 1 16.9 0.64 0.94 0.52 0.198
58 20.25 19 16 1 1 47 500 54 000 4 850 5 500 6 300 9 000 HR 322/28 37 34 52 49 55 2 4 1 1 14.6 0.37 1.6 0.89 0.243
58 20.25 19 16 1 1 42 000 49 500 4 300 5 050 6 300 9 000 HR 322/28 CJ 5DD 37 33 52 45 55 2 4 1 1 16.8 0.56 1.1 0.59 0.251
68 19.75 18 15 1.5 1.5 55 000 55 500 5 650 5 650 6 000 8 000 HR 303/28 39 37 59 58 61 2 4.5 1.5 1.5 14.5 0.31 1.9 1.1 0.341
68 19.75 18 14 1.5 1.5 49 500 50 500 5 000 5 150 5 600 7 500 HR 303/28 C 39 38 59 57 63 3 5.5 1.5 1.5 17.4 0.52 1.2 0.64 0.335
Remarks The suffix C represents medium-angle tapered roller bearings. Since they are designed for specific
applications, please consult NSK when using bearings with suffix C.
B 116 B 117
B110-181E.indd 116-117 11/20/13 4:56:54 PM

T Sa Sb
C
P = X Fr +Y Fa
Fa/ Fre Fa/ Fr>e
ra
r X Y X Y
B
P0 = 0.5Fr +Y0 Fa
a
30 47 12 12 9 0.3 0.3 17 600 24 400 1 800 2 490 7 500 10 000 HR 32906 J 2BD 34 34 44 42 44 3 3 0.3 0.3 9.2 0.32 1.9 1.0 0.074
55 17 17 13 1 1 36 000 44 500 3 700 4 550 6 700 9 000 HR 32006 XJ 4CC 39 35 49 47 53 3 4 1 1 13.5 0.43 1.4 0.77 0.172
55 20 20 16 1 1 42 000 54 000 4 250 5 500 6 700 9 000 HR 33006 J 2CE 39 35 49 48 52 3 4 1 1 13.1 0.29 2.1 1.1 0.208
62 17.25 16 14 1 1 43 000 47 500 4 400 4 850 6 000 8 000 HR 30206 J 3DB 39 37 56 52 58 2 3 1 1 13.9 0.37 1.6 0.88 0.238
62 17.25 16 12 1 1 35 500 37 000 3 650 3 800 5 600 7 500 HR 30206 C 39 36 56 49 59 2 5 1 1 17.8 0.68 0.88 0.49 0.221
62 21.25 20 17 1 1 52 000 60 000 5 300 6 150 6 000 8 500 HR 32206 J 3DC 39 36 56 51 58.5 2 4 1 1 15.4 0.37 1.6 0.88 0.297
62 21.25 20 16 1 1 48 000 56 000 4 900 5 750 6 000 8 000 HR 32206 C 39 35 56 48 59 2 5 1 1 17.8 0.55 1.1 0.60 0.293
62 25 25 19.5 1 1 66 500 79 500 6 800 8 100 6 000 8 000 HR 33206 J 2DE 39 35 56 52 59.5 5 5.5 1 1 16.1 0.34 1.8 0.97 0.355
72 20.75 19 16 1.5 1.5 59 500 60 000 6 050 6 100 5 300 7 500 HR 30306 J 2FB 41 40 63 62 66 3 4.5 1.5 1.5 15.1 0.32 1.9 1.1 0.403
72 20.75 19 14 1.5 1.5 56 500 55 500 5 800 5 650 5 300 7 100 HR 30306 C 41 38 63 59 67 3 6.5 1.5 1.5 18.5 0.55 1.1 0.60 0.383
72 20.75 19 14 1.5 1.5 49 000 52 500 5 000 5 350 4 800 6 700 HR 30306 DJ (7FB) 44 40 63 55 68 3 6.5 1.5 1.5 23.1 0.83 0.73 0.40 0.393
72 20.75 19 14 1.5 1.5 49 000 52 500 5 000 5 350 4 800 6 800 HR 31306 J 7FB 44 40 63 55 68 3 6.5 1.5 1.5 23.1 0.83 0.73 0.40 0.393
72 28.75 27 23 1.5 1.5 80 000 88 500 8 150 9 000 5 600 7 500 HR 32306 J 2FD 43 38 63 59 66 3 5.5 1.5 1.5 18.0 0.32 1.9 1.1 0.57
72 28.75 27 23 1.5 1.5 76 000 86 500 7 750 8 800 5 600 7 500 HR 32306 CJ 5FD 43 36 63 54 68 3 5.5 1.5 1.5 22.0 0.55 1.1 0.60 0.583
32 58 17 17 13 1 1 37 500 47 000 3 800 4 800 6 300 8 500 HR 320/32 XJ 4CC 41 37 52 49 55 3 4 1 1 14.2 0.45 1.3 0.73 0.191
58 21 20 16 1 1 41 000 50 000 4 150 5 100 6 300 8 500 330/32 41 37 52 50 55 2 4 1 1 13.8 0.31 1.9 1.1 0.225
65 18.25 17 15 1 1 48 500 54 000 4 950 5 500 5 600 8 000 HR 302/32 41 39 59 56 61 3 3 1 1 14.7 0.37 1.6 0.88 0.277
65 18.25 17 14 1 1 45 500 52 500 4 650 5 350 5 600 7 500 HR 302/32 C 41 39 59 54 62 3 4 1 1 16.9 0.55 1.1 0.60 0.273
65 22.25 21 18 1 1 56 000 65 000 5 700 6 650 6 000 8 000 HR 322/32 41 38 59 54 61 3 4 1 1 15.9 0.37 1.6 0.88 0.336
65 22.25 21 17 1 1 49 500 60 000 5 050 6 100 5 600 7 500 HR 322/32 C 41 39 59 51 62 3 5 1 1 20.2 0.59 1.0 0.56 0.335
65 26 26 20.5 1 1 70 000 86 500 7 150 8 850 5 600 8 000 HR 332/32 J 2DE 41 38 59 55 62 5 5.5 1 1 17.0 0.35 1.7 0.95 0.40
75 21.75 20 17 1.5 1.5 56 000 56 000 5 700 5 700 5 300 7 100 303/32 44 42 66 64 68 3 4.5 1.5 1.5 15.9 0.33 1.8 1.0 0.435
35 55 14 14 11.5 0.6 0.6 27 400 39 000 2 790 3 950 6 300 8 500 HR 32907 J 2BD 43 40 50 50 52.5 3 2.5 0.6 0.6 10.7 0.29 2.1 1.1 0.123
62 18 18 14 1 1 43 500 55 500 4 400 5 650 5 600 8 000 HR 32007 XJ 4CC 44 40 56 54 60 4 4 1 1 15.0 0.45 1.3 0.73 0.229
62 21 21 17 1 1 49 000 65 000 4 950 6 650 5 600 8 000 HR 33007 J 2CE 44 40 56 55 59 4 4 1 1 14.1 0.31 2.0 1.1 0.267
72 18.25 17 15 1.5 1.5 54 000 59 500 5 500 6 050 5 300 7 100 HR 30207 J 3DB 46 43 63 62 67 3 3 1.5 1.5 15.0 0.37 1.6 0.88 0.34
72 18.25 17 13 1.5 1.5 47 000 54 500 4 750 5 550 5 000 6 700 HR 30207 C 46 44 63 59 68 3 5 1.5 1.5 19.6 0.66 0.91 0.50 0.331
72 24.25 23 19 1.5 1.5 70 500 83 500 7 150 8 550 5 300 7 100 HR 32207 J 3DC 46 42 63 61 67.5 3 5 1.5 1.5 17.9 0.37 1.6 0.88 0.456
72 24.25 23 18 1.5 1.5 60 500 71 500 6 200 7 300 5 000 7 100 HR 32207 C 46 42 63 58 68.5 3 6 1.5 1.5 20.6 0.55 1.1 0.60 0.442
72 28 28 22 1.5 1.5 86 500 108 000 8 850 11 100 5 300 7 100 HR 33207 J 2DE 46 41 63 61 68 5 6 1.5 1.5 18.3 0.35 1.7 0.93 0.54
80 22.75 21 18 2 1.5 76 000 79 000 7 750 8 050 4 800 6 700 HR 30307 J 2FB 47 45 71 69 74 3 4.5 2 1.5 16.7 0.32 1.9 1.1 0.538
80 22.75 21 16 2 1.5 68 000 70 500 6 900 7 200 4 800 6 300 HR 30307 C 47 44 71 65 74 3 6.5 2 1.5 20.3 0.55 1.1 0.60 0.518
80 22.75 21 15 2 1.5 62 000 68 000 6 350 6 950 4 300 6 000 HR 30307 DJ 7FB 51 44 71 62 77 3 7.5 2 1.5 25.2 0.83 0.73 0.40 0.519
80 22.75 21 15 2 1.5 62 000 68 000 6 350 6 950 4 300 6 000 HR 31307 J 7FB 51 44 71 62 77 3 7.5 2 1.5 25.2 0.83 0.73 0.40 0.52
80 32.75 31 25 2 1.5 99 000 111 000 10 100 11 300 5 000 6 700 HR 32307 J 2FE 49 43 71 66 74 3 7.5 2 1.5 20.7 0.32 1.9 1.1 0.765
B 118 B 119
B110-181E.indd 118-119 11/20/13 4:56:55 PM

T Sa Sb
C
P = X Fr +Y Fa
Fa/ Fre Fa/ Fr>e
ra
r X Y X Y
B
P0 = 0.5Fr +Y0 Fa
a
40 62 15 15 12 0.6 0.6 34 000 47 000 3 450 4 800 5 600 7 500 HR 32908 J 2BC 48 44 57 57 59 3 3 0.6 0.6 11.5 0.29 2.1 1.1 0.161
68 19 19 14.5 1 1 53 000 71 000 5 400 7 250 5 300 7 100 HR 32008 XJ 3CD 49 45 62 60 65.5 4 4.5 1 1 15.0 0.38 1.6 0.87 0.28
68 22 22 18 1 1 59 000 81 500 6 000 8 300 5 300 7 100 HR 33008 J 2BE 49 45 62 61 65 4 4 1 1 14.6 0.28 2.1 1.2 0.322
75 26 26 20.5 1.5 1.5 78 500 101 000 8 000 10 300 4 800 6 700 HR 33108 J 2CE 51 46 66 65 71 4 5.5 1.5 1.5 18.0 0.36 1.7 0.93 0.503
80 19.75 18 16 1.5 1.5 63 500 70 000 6 450 7 150 4 800 6 300 HR 30208 J 3DB 51 48 71 69 75 3 3.5 1.5 1.5 16.6 0.37 1.6 0.88 0.437
80 24.75 23 19 1.5 1.5 77 000 90 500 7 900 9 200 4 800 6 300 HR 32208 J 3DC 51 48 71 68 75 3 5.5 1.5 1.5 18.9 0.37 1.6 0.88 0.548
80 24.75 23 19 1.5 1.5 74 000 90 500 7 550 9 200 4 500 6 300 HR 32208 CJ 5DC 51 47 71 65 76 3 5.5 1.5 1.5 21.9 0.55 1.1 0.60 0.558
80 32 32 25 1.5 1.5 107 000 137 000 10 900 14 000 4 800 6 300 HR 33208 J 2DE 51 46 71 67 76 5 7 1.5 1.5 20.8 0.36 1.7 0.92 0.744
90 25.25 23 20 2 1.5 90 500 101 000 9 250 10 300 4 300 5 600 HR 30308 J 2FB 52 52 81 76 82 3 5 2 1.5 19.5 0.35 1.7 0.96 0.758
90 25.25 23 18 2 1.5 84 500 93 500 8 600 9 500 4 300 5 600 HR 30308 C 52 50 81 72 84 3 7 2 1.5 22.8 0.53 1.1 0.62 0.735
90 25.25 23 17 2 1.5 80 000 89 500 8 150 9 150 3 800 5 300 HR 30308 DJ 7FB 56 50 81 70 87 3 8 2 1.5 28.7 0.83 0.73 0.40 0.728
90 25.25 23 17 2 1.5 80 000 89 500 8 150 9 150 3 800 5 300 HR 31308 J 7FB 56 50 81 70 87 3 8 2 1.5 28.7 0.83 0.73 0.40 0.728
90 35.25 33 27 2 1.5 120 000 145 000 12 200 14 800 4 300 6 000 HR 32308 J 2FD 54 50 81 73 82 3 8 2 1.5 23.4 0.35 1.7 0.96 1.05
45 68 15 15 12 0.6 0.6 34 500 50 500 3 550 5 150 5 000 6 700 HR 32909 J 2BC 53 50 63 62 64 3 3 0.6 0.6 12.3 0.32 1.9 1.0 0.187
75 20 20 15.5 1 1 60 000 83 000 6 150 8 450 4 500 6 300 HR 32009 XJ 3CC 54 51 69 67 72 4 4.5 1 1 16.6 0.39 1.5 0.84 0.354
75 24 24 19 1 1 69 000 99 000 7 050 10 100 4 800 6 300 HR 33009 J 2CE 54 51 69 67 71 4 5 1 1 16.3 0.29 2.0 1.1 0.414
80 26 26 20.5 1.5 1.5 84 000 113 000 8 550 11 600 4 500 6 000 HR 33109 J 3CE 56 51 71 69 77 4 5.5 1.5 1.5 19.1 0.38 1.6 0.86 0.552
85 20.75 19 16 1.5 1.5 68 500 79 500 6 950 8 100 4 300 6 000 HR 30209 J 3DB 56 53 76 74 80 3 4.5 1.5 1.5 18.3 0.41 1.5 0.81 0.488
85 24.75 23 19 1.5 1.5 83 000 102 000 8 500 10 400 4 300 6 000 HR 32209 J 3DC 56 53 76 73 81 3 5.5 1.5 1.5 20.1 0.41 1.5 0.81 0.602
85 24.75 23 19 1.5 1.5 75 500 95 500 7 700 9 750 4 300 5 600 HR 32209 CJ 5DC 56 52 76 70 82 3 5.5 1.5 1.5 23.6 0.59 1.0 0.56 0.603
85 32 32 25 1.5 1.5 111 000 147 000 11 300 15 000 4 300 6 000 HR 33209 J 3DE 56 51 76 72 81 5 7 1.5 1.5 22.0 0.39 1.6 0.86 0.817
95 29 26.5 20 2.5 2.5 88 500 109 000 9 050 11 100 3 600 5 000 T 7 FC045 7FC 60 53 83 71 91 3 9 2 2 32.1 0.87 0.69 0.38 0.918
95 36 35 30 2.5 2.5 139 000 174 000 14 200 17 800 4 000 5 300 T 2 ED045 2ED 60 54 83 79 89 5 6 2 2 23.5 0.32 1.9 1.02 1.22
100 27.25 25 22 2 1.5 112 000 127 000 11 400 12 900 3 800 5 300 HR 30309 J 2FB 57 58 91 86 93 3 5 2 1.5 21.1 0.35 1.7 0.96 1.01
100 27.25 25 18 2 1.5 95 500 109 000 9 750 11 100 3 400 4 800 HR 30309 DJ 7FB 61 57 91 79 96 3 9 2 1.5 31.5 0.83 0.73 0.40 0.957
100 27.25 25 18 2 1.5 95 500 109 000 9 750 11 100 3 400 4 800 HR 31309 J 7FB 61 57 91 79 96 3 9 2 1.5 31.5 0.83 0.73 0.40 0.947
100 38.25 36 30 2 1.5 144 000 177 000 14 700 18 000 3 800 5 300 HR 32309 J 2FD 59 56 91 82 93 3 8 2 1.5 25.0 0.35 1.7 0.96 1.42
50 100 36 35 30 2.5 2.5 144 000 185 000 14 600 18 800 3 800 5 000 T 2 ED050 2ED 65 59 88 83 94 6 6 2 2 24.2 0.34 1.8 0.96 1.3
72 15 15 12 0.6 0.6 36 000 54 000 3 650 5 500 4 500 6 300 HR 32910 J 2BC 58 54 67 66 69 3 3 0.6 0.6 13.5 0.34 1.8 0.97 0.193
80 20 20 15.5 1 1 61 000 87 000 6 250 8 900 4 300 6 000 HR 32010 XJ 3CC 59 56 74 71 77 4 4.5 1 1 17.9 0.42 1.4 0.78 0.38
80 24 24 19 1 1 70 500 104 000 7 150 10 600 4 300 6 000 HR 33010 J 2CE 59 55 74 71 76 4 5 1 1 17.4 0.32 1.9 1.0 0.452
85 26 26 20 1.5 1.5 89 000 126 000 9 100 12 800 4 300 5 600 HR 33110 J 3CE 61 56 76 74 82 4 6 1.5 1.5 20.3 0.41 1.5 0.8 0.597
90 21.75 20 17 1.5 1.5 76 000 91 500 7 750 9 300 4 000 5 300 HR 30210 J 3DB 61 58 81 79 85 3 4.5 1.5 1.5 19.6 0.42 1.4 0.79 0.557
90 24.75 23 19 1.5 1.5 87 500 109 000 8 900 11 100 4 000 5 300 HR 32210 J 3DC 61 57 81 78 86 3 5.5 1.5 1.5 21.0 0.42 1.4 0.79 0.642
90 24.75 23 18 1.5 1.5 77 500 102 000 7 900 10 400 3 800 5 300 HR 32210 CJ 5DC 61 58 81 76 87 3 6.5 1.5 1.5 24.6 0.59 1.0 0.56 0.655
90 32 32 24.5 1.5 1.5 118 000 165 000 12 100 16 800 4 000 5 300 HR 33210 J 3DE 61 56 81 76 87 5 7.5 1.5 1.5 23.2 0.41 1.5 0.80 0.867
105 32 29 22 3 3 109 000 133 000 11 100 13 600 3 200 4 500 T 7 FC050 7FC 74 59 91 78 100 5 10 2.5 2.5 36.4 0.87 0.69 0.38 1.22
110 29.25 27 23 2.5 2 130 000 148 000 13 300 15 100 3 400 4 800 HR 30310 J 2FB 65 65 100 95 102 3 6 2 2 23.1 0.35 1.7 0.96 1.28
110 29.25 27 19 2.5 2 114 000 132 000 11 700 13 400 3 200 4 300 HR 30310 DJ 7FB 70 62 100 87 105 3 10 2 2 34.3 0.83 0.73 0.40 1.26
110 29.25 27 19 2.5 2 114 000 132 000 11 700 13 400 3 200 4 300 HR 31310 J 7FB 70 62 100 87 105 3 10 2 2 34.3 0.83 0.73 0.40 1.26
110 42.25 40 33 2.5 2 176 000 220 000 17 900 22 400 3 600 4 800 HR 32310 J 2FD 68 62 100 91 102 3 9 2 2 28.0 0.35 1.7 0.96 1.88
110 42.25 40 33 2.5 2 164 000 218 000 16 800 22 200 3 400 4 800 HR 32310 CJ 5FD 68 59 100 82 103 3 9 2 2 32.8 0.55 1.1 0.60 1.93
B 120 B 121
B110-181E.indd 120-121 11/20/13 4:56:56 PM

T Sa Sb
C
P = X Fr +Y Fa
Fa/ Fre Fa/ Fr>e
ra
r X Y X Y
B
P0 = 0.5Fr +Y0 Fa
a
55 80 17 17 14 1 1 45 500 74 500 4 600 7 600 4 300 5 600 HR 32911 J 2BC 64 60 74 73 76 4 3 1 1 14.6 0.31 1.9 1.1 0.282
90 23 23 17.5 1.5 1.5 81 500 117 000 8 300 11 900 3 800 5 300 HR 32011 XJ 3CC 66 62 81 80 86 4 5.5 1.5 1.5 19.7 0.41 1.5 0.81 0.568
90 27 27 21 1.5 1.5 91 500 138 000 9 300 14 000 3 800 5 300 HR 33011 J 2CE 66 62 81 80 86 5 6 1.5 1.5 19.2 0.31 1.9 1.1 0.657
95 30 30 23 1.5 1.5 112 000 158 000 11 500 16 100 3 800 5 000 HR 33111 J 3CE 66 62 86 82 91 5 7 1.5 1.5 22.4 0.37 1.6 0.88 0.877
100 22.75 21 18 2 1.5 94 500 113 000 9 650 11 500 3 600 5 000 HR 30211 J 3DB 67 64 91 89 94 4 4.5 2 1.5 20.9 0.41 1.5 0.81 0.736
100 26.75 25 21 2 1.5 110 000 137 000 11 200 14 000 3 600 5 000 HR 32211 J 3DC 67 63 91 87 95 4 5.5 2 1.5 22.7 0.41 1.5 0.81 0.859
100 35 35 27 2 1.5 141 000 193 000 14 400 19 700 3 600 5 000 HR 33211 J 3DE 67 62 91 86 96 6 8 2 1.5 25.2 0.40 1.5 0.83 1.18
115 34 31 23.5 3 3 126 000 164 000 12 800 16 700 3 000 4 300 T 7 FC055 7FC 73 66 101 86 109 4 10.5 2.5 2.5 39.0 0.87 0.69 0.38 1.58
120 31.5 29 25 2.5 2 150 000 171 000 15 200 17 500 3 200 4 300 HR 30311 J 2FB 70 71 110 104 111 4 6.5 2 2 24.6 0.35 1.7 0.96 1.63
120 31.5 29 21 2.5 2 131 000 153 000 13 400 15 600 2 800 4 000 HR 30311 DJ 7FB 75 67 110 94 114 4 10.5 2 2 37.0 0.83 0.73 0.40 1.58
120 31.5 29 21 2.5 2 131 000 153 000 13 400 15 600 2 800 4 000 HR 31311 J 7FB 75 67 110 94 114 4 10.5 2 2 37.0 0.83 0.73 0.40 1.58
120 45.5 43 35 2.5 2 204 000 258 000 20 800 26 300 3 200 4 300 HR 32311 J 2FD 73 67 110 99 111 4 10.5 2 2 29.9 0.35 1.7 0.96 2.39
120 45.5 43 35 2.5 2 195 000 262 000 19 900 26 700 3 200 4 300 HR 32311 CJ 5FD 73 65 110 91 112 4 10.5 2 2 35.8 0.55 1.1 0.60 2.47
60 85 17 17 14 1 1 49 000 84 500 5 000 8 650 3 800 5 300 HR 32912 J 2BC 69 65 79 78 81 4 3 1 1 15.5 0.33 1.8 1.0 0.306
95 23 23 17.5 1.5 1.5 85 500 127 000 8 700 12 900 3 600 5 000 HR 32012 XJ 4CC 71 66 86 85 91 4 5.5 1.5 1.5 20.9 0.43 1.4 0.77 0.608
95 27 27 21 1.5 1.5 96 000 150 000 9 800 15 300 3 600 5 000 HR 33012 J 2CE 71 66 86 85 90 5 6 1.5 1.5 20.0 0.33 1.8 1.0 0.713
100 30 30 23 1.5 1.5 115 000 166 000 11 700 16 900 3 400 4 800 HR 33112 J 3CE 71 68 91 88 96 5 7 1.5 1.5 23.6 0.40 1.5 0.83 0.91
110 23.75 22 19 2 1.5 104 000 123 000 10 600 12 500 3 400 4 500 HR 30212 J 3EB 72 69 101 96 103 4 4.5 2 1.5 22.0 0.41 1.5 0.81 0.930
110 29.75 28 24 2 1.5 131 000 167 000 13 400 17 000 3 400 4 500 HR 32212 J 3EC 72 68 101 95 104 4 5.5 2 1.5 24.1 0.41 1.5 0.81 1.18
110 38 38 29 2 1.5 166 000 231 000 16 900 23 600 3 400 4 500 HR 33212 J 3EE 72 68 101 94 105 6 9 2 1.5 27.6 0.40 1.5 0.82 1.56
125 37 33.5 26 3 3 151 000 197 000 15 400 20 100 2 800 3 800 T 7 FC060 7FC 78 72 111 94 119 4 11 2.5 2.5 41.4 0.82 0.73 0.40 2.03
130 33.5 31 26 3 2.5 174 000 201 000 17 700 20 500 3 000 4 000 HR 30312 J 2FB 78 77 118 112 120 4 7.5 2.5 2 26.0 0.35 1.7 0.96 2.03
130 33.5 31 22 3 2.5 151 000 177 000 15 400 18 100 2 600 3 800 HR 30312 DJ 7FB 84 74 118 103 125 4 11.5 2.5 2 40.3 0.83 0.73 0.40 1.98
130 33.5 31 22 3 2.5 151 000 177 000 15 400 18 100 2 600 3 800 HR 31312 J 7FB 84 74 118 103 125 4 11.5 2.5 2 40.3 0.83 0.73 0.40 1.98
130 48.5 46 37 3 2.5 233 000 295 000 23 700 30 000 3 000 4 000 HR 32312 J 2FD 81 74 118 107 120 4 11.5 2.5 2 31.4 0.35 1.7 0.96 2.96
130 48.5 46 35 3 2.5 196 000 249 000 20 000 25 400 2 800 3 800 32312 C 81 74 116 102 125 4 13.5 2.5 2 39.9 0.58 1.0 0.57 2.86
65 90 17 17 14 1 1 49 000 86 500 5 000 8 800 3 600 5 000 HR 32913 J 2BC 74 70 84 82 86 4 3 1 1 16.8 0.35 1.7 0.93 0.323
100 23 23 17.5 1.5 1.5 86 500 132 000 8 800 13 500 3 400 4 500 HR 32013 XJ 4CC 76 71 91 90 97 4 5.5 1.5 1.5 22.4 0.46 1.3 0.72 0.646
100 27 27 21 1.5 1.5 97 500 156 000 9 950 15 900 3 400 4 500 HR 33013 J 2CE 76 71 91 90 96 5 6 1.5 1.5 21.1 0.35 1.7 0.95 0.76
110 34 34 26.5 1.5 1.5 148 000 218 000 15 100 22 200 3 200 4 300 HR 33113 J 3DE 76 73 101 96 106 6 7.5 1.5 1.5 26.0 0.39 1.5 0.85 1.32
120 24.75 23 20 2 1.5 122 000 151 000 12 500 15 400 3 000 4 000 HR 30213 J 3EB 77 78 111 106 113 4 4.5 2 1.5 23.8 0.41 1.5 0.81 1.18
120 32.75 31 27 2 1.5 157 000 202 000 16 000 20 600 3 000 4 000 HR 32213 J 3EC 77 75 111 104 115 4 5.5 2 1.5 27.1 0.41 1.5 0.81 1.55
120 41 41 32 2 1.5 202 000 282 000 20 600 28 800 3 000 4 000 HR 33213 J 3EE 77 74 111 102 115 6 9 2 1.5 29.2 0.39 1.5 0.85 2.04
140 36 33 28 3 2.5 200 000 233 000 20 400 23 800 2 600 3 600 HR 30313 J 2GB 83 83 128 121 130 4 8 2.5 2 27.9 0.35 1.7 0.96 2.51
140 36 33 23 3 2.5 173 000 205 000 17 700 20 900 2 400 3 400 HR 30313 DJ 7GB 89 80 128 111 133 4 13 2.5 2 43.2 0.83 0.73 0.40 2.43
140 36 33 23 3 2.5 173 000 205 000 17 700 20 900 2 400 3 400 HR 31313 J 7GB 89 80 128 111 133 4 13 2.5 2 43.2 0.83 0.73 0.40 2.43
140 51 48 39 3 2.5 267 000 340 000 27 300 35 000 2 800 3 800 HR 32313 J 2GD 86 80 128 116 130 4 12 2.5 2 34.0 0.35 1.7 0.96 3.6
B 122 B 123
B110-181E.indd 122-123 11/20/13 4:56:57 PM

T Sa Sb
C
P = X Fr +Y Fa
Fa/ Fre Fa/ Fr>e
ra
r X Y X Y
B
P0 = 0.5Fr +Y0 Fa
a
70 100 20 20 16 1 1 70 000 113 000 7 150 11 500 3 200 4 500 HR 32914 J 2BC 79 76 94 93 96 4 4 1 1 17.6 0.32 1.9 1.1 0.494
110 25 25 19 1.5 1.5 104 000 158 000 10 600 16 100 3 200 4 300 HR 32014 XJ 4CC 81 77 101 98 105 5 6 1.5 1.5 23.7 0.43 1.4 0.76 0.869
110 31 31 25.5 1.5 1.5 127 000 204 000 12 900 20 800 3 000 4 300 HR 33014 J 2CE 81 78 101 100 105 5 5.5 1.5 1.5 22.2 0.28 2.1 1.2 1.11
120 37 37 29 2 1.5 177 000 262 000 18 100 26 700 3 000 4 000 HR 33114 J 3DE 82 79 111 104 115 6 8 2 1.5 27.9 0.38 1.6 0.87 1.71
125 26.25 24 21 2 1.5 132 000 163 000 13 500 16 700 2 800 4 000 HR 30214 J 3EB 82 81 116 110 118 4 5 2 1.5 25.6 0.42 1.4 0.79 1.3
125 33.25 31 27 2 1.5 157 000 205 000 16 100 20 900 2 800 4 000 HR 32214 J 3EC 82 80 116 108 119 4 6 2 1.5 28.6 0.42 1.4 0.79 1.66
125 41 41 32 2 1.5 209 000 299 000 21 300 30 500 2 800 4 000 HR 33214 J 3EE 82 78 116 107 120 7 9 2 1.5 30.4 0.41 1.5 0.81 2.15
140 39 35.5 27 3 3 177 000 229 000 18 000 23 400 2 400 3 400 T 7 FC070 7FC 88 79 126 106 133 5 12 2.5 2.5 46.4 0.87 0.69 0.38 2.55
150 38 35 30 3 2.5 227 000 268 000 23 200 27 400 2 400 3 400 HR 30314 J 2GB 88 89 138 132 140 4 8 2.5 2 29.7 0.35 1.7 0.96 3.03
150 38 35 25 3 2.5 192 000 229 000 19 600 23 300 2 200 3 200 HR 30314 DJ 7GB 94 85 138 118 142 4 13 2.5 2 45.8 0.83 0.73 0.40 2.94
150 38 35 25 3 2.5 192 000 229 000 19 600 23 300 2 200 3 200 HR 31314 J 7GB 94 85 138 118 142 4 13 2.5 2 45.8 0.83 0.73 0.40 2.94
150 54 51 42 3 2.5 300 000 390 000 30 500 39 500 2 600 3 400 HR 32314 J 2GD 91 86 138 124 140 4 12 2.5 2 36.1 0.35 1.7 0.96 4.35
150 54 51 42 3 2.5 280 000 390 000 28 600 39 500 2 400 3 400 HR 32314 CJ 5GD 91 84 138 115 141 4 12 2.5 2 43.3 0.55 1.1 0.60 4.47
75 105 20 20 16 1 1 72 500 120 000 7 400 12 300 3 200 4 300 HR 32915 J 2BC 84 81 99 98 101 4 4 1 1 18.7 0.33 1.8 0.99 0.53
115 25 25 19 1.5 1.5 109 000 171 000 11 100 17 400 3 000 4 000 HR 32015 XJ 4CC 86 82 106 103 110 5 6 1.5 1.5 25.1 0.46 1.3 0.72 0.925
115 31 31 25.5 1.5 1.5 133 000 220 000 13 500 22 500 3 000 4 000 HR 33015 J 2CE 86 83 106 104 110 6 5.5 1.5 1.5 23.0 0.30 2.0 1.1 1.18
125 37 37 29 2 2 182 000 275 000 18 600 28 100 2 800 3 800 HR 33115 J 3DE 87 83 115 109 120 6 8 2 2 29.2 0.40 1.5 0.83 1.8
130 27.25 25 22 2 1.5 143 000 182 000 14 600 18 500 2 800 3 800 HR 30215 J 4DB 87 85 121 115 124 4 5 2 1.5 27.0 0.44 1.4 0.76 1.43
130 33.25 31 27 2 1.5 165 000 219 000 16 900 22 400 2 800 3 800 HR 32215 J 4DC 87 84 121 113 125 4 6 2 1.5 29.8 0.44 1.4 0.76 1.72
130 41 41 31 2 1.5 215 000 315 000 21 900 32 000 2 800 3 800 HR 33215 J 3EE 87 83 121 111 125 7 10 2 1.5 31.6 0.43 1.4 0.77 2.25
160 40 37 31 3 2.5 253 000 300 000 25 800 30 500 2 400 3 200 HR 30315 J 2GB 93 95 148 141 149 4 9 2.5 2 31.8 0.35 1.7 0.96 3.63
160 40 37 26 3 2.5 211 000 251 000 21 500 25 600 2 200 3 000 HR 30315 DJ 7GB 99 91 148 129 152 6 14 2.5 2 48.8 0.83 0.73 0.40 3.47
160 40 37 26 3 2.5 211 000 251 000 21 500 25 600 2 200 3 000 HR 31315 J 7GB 99 91 148 129 152 6 14 2.5 2 48.8 0.83 0.73 0.40 3.47
160 58 55 45 3 2.5 340 000 445 000 35 000 45 500 2 400 3 200 HR 32315 J 2GD 96 91 148 134 149 4 13 2.5 2 38.9 0.35 1.7 0.96 5.31
160 58 55 43 3 2.5 310 000 420 000 32 000 43 000 2 200 3 200 32315 CA 96 90 148 124 153 4 15 2.5 2 47.7 0.58 1.0 0.57 5.3
80 110 20 20 16 1 1 75 000 128 000 7 650 13 100 3 000 4 000 HR 32916 J 2BC 89 85 104 102 106 4 4 1 1 19.8 0.35 1.7 0.94 0.56
125 29 29 22 1.5 1.5 140 000 222 000 14 300 22 700 2 800 3 600 HR 32016 XJ 3CC 91 89 116 112 120 6 7 1.5 1.5 26.9 0.42 1.4 0.78 1.32
125 36 36 29.5 1.5 1.5 172 000 282 000 17 500 28 800 2 800 3 600 HR 33016 J 2CE 91 88 116 112 119 6 6.5 1.5 1.5 25.5 0.28 2.2 1.2 1.66
130 37 37 29 2 1.5 186 000 289 000 19 000 29 400 2 600 3 600 HR 33116 J 3DE 82 88 121 113 126 6 8 2 1.5 30.4 0.42 1.4 0.79 1.88
140 28.25 26 22 2.5 2 157 000 195 000 16 000 19 900 2 600 3 400 HR 30216 J 3EB 95 91 130 124 132 4 6 2 2 28.1 0.42 1.4 0.79 1.68
140 28.25 26 20 2.5 2 147 000 190 000 15 000 19 400 2 400 3 400 30216 CA 95 92 130 122 133 4 8 2 2 33.8 0.58 1.0 0.57 1.66
140 35.25 33 28 2.5 2 192 000 254 000 19 600 25 900 2 600 3 400 HR 32216 J 3EC 95 90 130 122 134 4 7 2 2 30.6 0.42 1.4 0.79 2.13
140 46 46 35 2.5 2 256 000 385 000 26 200 39 000 2 600 3 400 HR 33216 J 3EE 95 89 130 119 135 7 11 2 2 34.8 0.43 1.4 0.78 2.93
170 42.5 39 33 3 2.5 276 000 330 000 28 200 33 500 2 200 3 000 HR 30316 J 2GB 98 102 158 150 159 4 9.5 2.5 2 34.0 0.35 1.7 0.96 4.27
170 42.5 39 27 3 2.5 235 000 283 000 24 000 28 900 2 000 2 800 HR 30316 DJ 7GB 104 97 158 136 159 6 15.5 2.5 2 51.8 0.83 0.73 0.40 4.07
170 42.5 39 27 3 2.5 235 000 283 000 24 000 28 900 2 000 2 800 HR 31316 J 7GB 104 97 158 136 159 6 15.5 2.5 2 51.8 0.83 0.73 0.40 4.07
170 61.5 58 48 3 2.5 385 000 505 000 39 000 51 500 2 200 3 000 HR 32316 J 2GD 101 98 158 143 159 4 13.5 2.5 2 41.4 0.35 1.7 0.96 6.35
170 61.5 58 48 3 2.5 365 000 530 000 37 500 54 000 2 200 3 000 HR 32316 CJ 5GD 101 95 158 132 160 4 13.5 2.5 2 49.3 0.55 1.1 0.60 6.59
Remarks The suffix CA represents medium-angle tapered roller bearings. Since they are designed for specific
applications, please consult NSK when using bearings with suffix CA.
B 124 B 125
B110-181E.indd 124-125 11/20/13 4:56:58 PM

T Sa Sb
C
P = X Fr +Y Fa
Fa/ Fre Fa/ Fr>e
ra
r X Y X Y
B
P0 = 0.5Fr +Y0 Fa
a
85 120 23 23 18 1.5 1.5 93 500 157 000 9 550 16 000 2 800 3 800 HR 32917 J 2BC 96 92 111 111 115 5 5 1.5 1.5 20.9 0.33 1.8 1.0 0.8
130 29 29 22 1.5 1.5 143 000 231 000 14 600 23 600 2 600 3 600 HR 32017 XJ 4CC 96 94 121 116 125 6 7 1.5 1.5 28.2 0.44 1.4 0.75 1.38
130 36 36 29.5 1.5 1.5 180 000 305 000 18 400 31 000 2 600 3 600 HR 33017 J 2CE 96 94 121 117 125 6 6.5 1.5 1.5 26.5 0.29 2.1 1.1 1.75
140 41 41 32 2.5 2 230 000 365 000 23 500 37 000 2 400 3 400 HR 33117 J 3DE 100 94 130 122 135 7 9 2 2 32.7 0.41 1.5 0.81 2.51
150 30.5 28 24 2.5 2 184 000 233 000 18 700 23 800 2 400 3 200 HR 30217 J 3EB 100 97 140 133 141 5 6.5 2 2 30.3 0.42 1.4 0.79 2.12
150 30.5 28 22 2.5 2 171 000 226 000 17 500 23 000 2 200 3 200 30217 CA 100 98 140 131 142 5 8.5 2 2 36.2 0.58 1.0 0.57 2.07
150 38.5 36 30 2.5 2 210 000 277 000 21 400 28 200 2 200 3 200 HR 32217 J 3EC 100 96 140 131 142 5 8.5 2 2 33.9 0.42 1.4 0.79 2.64
150 49 49 37 2.5 2 281 000 415 000 28 700 42 500 2 400 3 200 HR 33217 J 3EE 100 95 140 129 144 7 12 2 2 37.3 0.42 1.4 0.79 3.57
180 44.5 41 34 4 3 310 000 375 000 31 500 38 000 2 000 2 800 HR 30317 J 2GB 106 108 166 157 167 5 10.5 3 2.5 35.8 0.35 1.7 0.96 5.08
180 44.5 41 28 4 3 261 000 315 000 26 600 32 000 1 900 2 600 HR 30317 DJ 7GB 113 103 166 144 169 6 16.5 3 2.5 55.4 0.83 0.73 0.40 4.88
180 44.5 41 28 4 3 261 000 315 000 26 600 32 000 1 900 2 600 HR 31317 J 7GB 113 103 166 144 169 6 16.5 3 2.5 55.4 0.83 0.73 0.40 4.88
180 63.5 60 49 4 3 410 000 535 000 42 000 54 500 2 000 2 800 HR 32317 J 2GD 110 104 166 151 167 5 14.5 3 2.5 43.6 0.35 1.7 0.96 7.31
90 125 23 23 18 1.5 1.5 97 000 167 000 9 850 17 000 2 600 3 600 HR 32918 J 2BC 101 97 116 116 120 5 5 1.5 1.5 22.0 0.34 1.8 0.96 0.838
140 32 32 24 2 1.5 170 000 273 000 17 300 27 800 2 400 3 200 HR 32018 XJ 3CC 102 99 131 124 134 6 8 2 1.5 29.7 0.42 1.4 0.78 1.78
140 39 39 32.5 2 1.5 220 000 360 000 22 400 37 000 2 400 3 200 HR 33018 J 2CE 102 99 131 129 135 7 6.5 2 1.5 27.9 0.27 2.2 1.2 2.21
150 45 45 35 2.5 2 259 000 405 000 26 500 41 500 2 400 3 200 HR 33118 J 3DE 105 100 140 132 144 7 10 2 2 35.2 0.40 1.5 0.83 3.14
160 32.5 30 26 2.5 2 201 000 256 000 20 500 26 100 2 200 3 000 HR 30218 J 3FB 105 103 150 141 150 5 6.5 2 2 31.7 0.42 1.4 0.79 2.6
160 42.5 40 34 2.5 2 256 000 350 000 26 100 35 500 2 200 3 000 HR 32218 J 3FC 105 102 150 139 152 5 8.5 2 2 36.2 0.42 1.4 0.79 3.41
190 46.5 43 36 4 3 345 000 425 000 35 500 43 000 1 900 2 600 HR 30318 J 2GB 111 114 176 176 176 5 10.5 3 2.5 37.3 0.35 1.7 0.96 5.91
190 46.5 43 30 4 3 264 000 315 000 26 900 32 000 1 800 2 400 HR 30318 DJ 7GB 118 110 176 152 179 6 16.5 3 2.5 58.7 0.83 0.73 0.40 5.52
190 46.5 43 30 4 3 264 000 315 000 26 900 32 000 1 800 2 400 HR 31318 J 7GB 118 110 176 152 179 6 16.5 3 2.5 58.7 0.83 0.73 0.40 5.52
190 67.5 64 53 4 3 450 000 590 000 46 000 60 500 2 000 2 600 HR 32318 J 2GD 115 109 176 158 177 5 14.5 3 2.5 46.5 0.35 1.7 0.96 8.6
95 130 23 23 18 1.5 1.5 98 000 172 000 10 000 17 500 2 400 3 400 HR 32919 J 2BC 106 102 121 121 125 5 5 1.5 1.5 23.2 0.36 1.7 0.92 0.877
145 32 32 24 2 1.5 173 000 283 000 17 600 28 900 2 400 3 200 HR 32019 XJ 4CC 107 104 136 131 140 6 8 2 1.5 31.2 0.44 1.4 0.75 1.88
145 39 39 32.5 2 1.5 231 000 390 000 23 500 39 500 2 400 3 200 HR 33019 J 2CE 107 103 136 133 139 7 6.5 2 1.5 28.6 0.28 2.2 1.2 2.3
160 46 46 38 3 3 283 000 445 000 28 800 45 500 2 200 3 000 T 2 ED095 2ED 113 108 146 141 152 6 8 2.5 2.5 34.5 0.34 1.8 0.97 3.74
170 34.5 32 27 3 2.5 223 000 286 000 22 800 29 200 2 200 2 800 HR 30219 J 3FB 113 110 158 150 159 5 7.5 2.5 2 33.7 0.42 1.4 0.79 3.13
170 45.5 43 37 3 2.5 289 000 400 000 29 500 40 500 2 200 2 800 HR 32219 J 3FC 113 108 158 147 161 5 8.5 2.5 2 39.3 0.42 1.4 0.79 4.22
200 49.5 45 38 4 3 370 000 455 000 38 000 46 500 1 900 2 600 HR 30319 J 2GB 116 119 186 172 184 5 11.5 3 2.5 38.6 0.35 1.7 0.96 6.92
200 49.5 45 36 4 3 350 000 435 000 35 500 44 000 1 800 2 400 30319 CA 116 119 186 168 188 5 13.5 3 2.5 48.6 0.54 1.1 0.61 6.71
200 49.5 45 32 4 3 310 000 375 000 31 500 38 500 1 700 2 400 HR 30319 DJ 7GB 123 115 186 158 187 6 17.5 3 2.5 61.9 0.83 0.73 0.40 6.64
200 49.5 45 32 4 3 310 000 375 000 31 500 38 500 1 700 2 400 HR 31319 J 7GB 123 115 186 158 187 6 17.5 3 2.5 61.9 0.83 0.73 0.40 6.64
200 71.5 67 55 4 3 525 000 710 000 53 500 72 500 1 900 2 600 HR 32319 J 2GD 120 115 186 167 186 5 16.5 3 2.5 48.6 0.35 1.7 0.96 10.4
100 140 25 25 20 1.5 1.5 117 000 205 000 12 000 20 900 2 200 3 200 HR 32920 J 2CC 111 109 132 132 134 5 5 1.5 1.5 24.2 0.33 1.8 1.0 1.18
145 24 22.5 17.5 3 3 113 000 163 000 11 500 16 600 2 200 3 000 T 4 CB100 4CB 118 108 135 135 142 6 6.5 2.5 2.5 30.1 0.47 1.3 0.70 1.18
150 32 32 24 2 1.5 176 000 294 000 17 900 30 000 2 200 3 000 HR 32020 XJ 4CC 112 109 141 136 144 6 8 2 1.5 32.5 0.46 1.3 0.72 1.95
150 39 39 32.5 2 1.5 235 000 405 000 24 000 41 500 2 200 3 000 HR 33020 J 2CE 112 107 141 137 143 7 6.5 2 1.5 29.3 0.29 2.1 1.2 2.38
165 52 52 40 2.5 2 315 000 515 000 32 500 52 500 2 000 2 800 HR 33120 J 3EE 115 110 155 144 159 8 12 2 2 40.5 0.41 1.5 0.81 4.32
180 37 34 29 3 2.5 255 000 330 000 26 000 34 000 2 000 2 600 HR 30220 J 3FB 118 116 168 158 168 5 8 2.5 2 36.1 0.42 1.4 0.79 3.78
180 49 46 39 3 2.5 325 000 450 000 33 000 46 000 2 000 2 600 HR 32220 J 3FC 118 115 168 155 171 5 10 2.5 2 41.5 0.42 1.4 0.79 5.05
180 63 63 48 3 2.5 410 000 635 000 42 000 65 000 2 000 2 600 HR 33220 J 3FE 118 113 168 152 172 10 15 2.5 2 46.0 0.40 1.5 0.82 6.76
215 51.5 47 39 4 3 425 000 525 000 43 000 53 500 1 700 2 400 HR 30320 J 2GB 121 128 201 185 197 5 12.5 3 2.5 41.4 0.35 1.7 0.96 8.41
215 56.5 51 35 4 3 385 000 505 000 39 000 51 500 1 500 2 200 HR 31320 J 7GB 136 125 201 169 202 7 21.5 3 2.5 67.7 0.83 0.73 0.40 9.02
215 77.5 73 60 4 3 565 000 755 000 57 500 77 000 1 700 2 400 HR 32320 J 2GD 125 125 201 178 200 5 17.5 3 2.5 53.2 0.35 1.7 0.96 12.7
Remarks The suffix CA represents medium-angle tapered roller bearings. Since they are designed for specific
applications, please consult NSK when using bearings with suffix CA.
B 126 B 127
B110-181E.indd 126-127 11/20/13 4:56:59 PM

T Sa Sb
C
P = X Fr +Y Fa
Fa/ Fr e Fa/ Fr e
ra
r X Y X Y
B
P0 = 0.5Fr +Y0 Fa
When Fr 0.5Fr +Y0 Fa , use P0 = Fr
a
105 145 25 25 20 1.5 1.5 119 000 212 000 12 100 21 600 2 200 3 000 HR 32921 J 2CC 116 114 137 137 140 5 5 1.5 1.5 25.3 0.34 1.8 0.96 1.23
160 35 35 26 2.5 2 204 000 340 000 20 800 34 500 2 000 2 800 HR 32021 XJ 4DC 120 115 150 144 154 6 9 2 2 34.3 0.44 1.4 0.74 2.48
160 43 43 34 2.5 2 256 000 435 000 26 100 44 000 2 000 2 800 HR 33021 J 2DE 120 115 150 146 153 7 9 2 2 30.9 0.28 2.1 1.2 3.03
190 39 36 30 3 2.5 280 000 365 000 28 500 37 500 1 900 2 600 HR 30221 J 3FB 123 123 178 166 177 6 9 2.5 2 38.1 0.42 1.4 0.79 4.51
190 53 50 43 3 2.5 360 000 510 000 37 000 52 000 1 900 2 600 HR 32221 J 3FC 123 120 178 162 180 5 10 2.5 2 44.8 0.42 1.4 0.79 6.25
225 53.5 49 41 4 3 455 000 565 000 46 500 57 500 1 600 2 200 HR 30321 J 2GB 126 133 211 195 206 6 12.5 3 2.5 43.3 0.35 1.7 0.96 9.52
225 58 53 36 4 3 415 000 540 000 42 000 55 000 1 500 2 000 HR 31321 J 7GB 141 130 211 177 211 7 22 3 2.5 70.2 0.83 0.73 0.40 10
225 81.5 77 63 4 3 670 000 925 000 68 000 94 500 1 700 2 200 HR 32321 J 2GD 130 129 211 186 209 6 18.5 3 2.5 55.2 0.35 1.7 0.96 14.9
110 150 25 25 20 1.5 1.5 123 000 224 000 12 500 22 800 2 200 2 800 HR 32922 J 2CC 121 119 142 142 145 5 5 1.5 1.5 26.5 0.36 1.7 0.93 1.29
170 38 38 29 2.5 2 236 000 390 000 24 000 40 000 2 000 2 600 HR 32022 XJ 4DC 125 121 160 153 163 7 9 2 2 35.9 0.43 1.4 0.77 3.09
170 47 47 37 2.5 2 294 000 515 000 30 000 52 500 2 000 2 600 HR 33022 J 2DE 125 121 160 153 161 7 10 2 2 33.7 0.29 2.1 1.2 3.84
180 56 56 43 2.5 2 365 000 610 000 37 500 62 000 1 900 2 600 HR 33122 J 3EE 125 121 170 156 174 9 13 2 2 44.1 0.42 1.4 0.79 5.54
200 41 38 32 3 2.5 315 000 420 000 32 000 43 000 1 800 2 400 HR 30222 J 3FB 128 129 188 175 187 6 9 2.5 2 40.2 0.42 1.4 0.79 5.28
200 56 53 46 3 2.5 400 000 565 000 40 500 57 500 1 800 2 400 HR 32222 J 3FC 128 127 188 171 190 5 10 2.5 2 47.2 0.42 1.4 0.79 7.35
240 54.5 50 42 4 3 485 000 595 000 49 500 60 500 1 500 2 000 HR 30322 J 2GB 131 143 226 208 220 6 12.5 3 2.5 45.1 0.35 1.7 0.96 11
240 63 57 38 4 3 470 000 605 000 48 000 62 000 1 400 1 900 HR 31322 J 7GB 146 136 226 191 224 7 25 3 2.5 74.8 0.83 0.73 0.40 12.3
240 84.5 80 65 4 3 675 000 910 000 68 500 93 000 1 500 2 000 HR 32322 J 2GD 135 139 226 201 222 6 19.5 3 2.5 58.6 0.35 1.7 0.96 17.1
120 165 29 29 23 1.5 1.5 161 000 291 000 16 400 29 700 1 900 2 600 HR 32924 J 2CC 131 129 156 155 160 6 6 1.5 1.5 29.2 0.35 1.7 0.95 1.8
170 27 25 19.5 3 3 153 000 243 000 51 600 24 800 1 800 2 600 T 4 CB120 4CB 138 129 158 158 164 7 7.5 2.5 2.5 35.0 0.47 1.3 0.70 1.78
180 38 38 29 2.5 2 242 000 405 000 24 600 41 000 1 800 2 400 HR 32024 XJ 4DC 135 131 170 162 173 7 9 2 2 39.7 0.46 1.3 0.72 3.27
180 48 48 38 2.5 2 300 000 540 000 30 500 55 000 1 800 2 600 HR 33024 J 2DE 135 130 168 161 171 6 10 2 2 36.0 0.31 2.0 1.1 4.2
200 62 62 48 2.5 2 460 000 755 000 46 500 77 000 1 700 2 400 HR 33124 J 3FE 135 133 190 173 192 9 14 2 2 47.9 0.40 1.5 0.83 7.67
215 43.5 40 34 3 2.5 335 000 450 000 34 000 46 000 1 600 2 200 HR 30224 J 4FB 138 141 203 190 201 6 9.5 2.5 2 44.4 0.44 1.4 0.76 6.28
215 61.5 58 50 3 2.5 440 000 635 000 44 500 65 000 1 600 2 200 HR 32224 J 4FD 138 137 203 181 204 6 11.5 2.5 2 52.1 0.44 1.4 0.76 9.0
260 59.5 55 46 4 3 535 000 655 000 54 500 67 000 1 400 1 900 HR 30324 J 2GB 141 154 246 223 237 6 13.5 3 2.5 50.0 0.35 1.7 0.96 13.9
260 68 62 42 4 3 560 000 730 000 57 000 74 500 1 300 1 800 HR 31324 J 7GB 156 148 246 206 244 9 26 3 2.5 81.7 0.83 0.73 0.40 15.6
260 90.5 86 69 4 3 770 000 1 060 000 78 500 108 000 1 400 1 900 HR 32324 J 2GD 145 149 246 216 239 6 21.5 3 2.5 62.5 0.35 1.7 0.96 21.8
130 180 32 30 26 2 1.5 167 000 281 000 17 000 28 600 1 800 2 400 32926 142 141 171 168 175 6 6 2 1.5 34.7 0.36 1.7 0.92 2.25
180 32 32 25 2 1.5 200 000 365 000 20 400 37 500 1 800 2 400 HR 32926 J 2CC 142 140 170 168 173 6 7 2 1.5 31.4 0.34 1.8 0.97 2.46
185 29 27 21 3 3 183 000 296 000 18 600 30 000 1 700 2 400 T 4 CB130 4CB 148 141 171 171 179 8 8 2.5 2.5 37.5 0.47 1.3 0.70 2.32
200 45 45 34 2.5 2 320 000 535 000 32 500 54 500 1 600 2 200 HR 32026 XJ 4EC 145 144 190 179 192 8 11 2 2 43.9 0.43 1.4 0.76 5.06
200 55 55 43 2.5 2 395 000 715 000 40 500 73 000 1 700 2 200 HR 33026 J 2EE 145 144 188 179 192 8 12 2 2 42.4 0.34 1.8 0.97 6.25
230 43.75 40 34 4 3 375 000 505 000 38 000 51 500 1 500 2 000 HR 30226 J 4FB 151 151 216 205 217 7 9.5 3 2.5 45.9 0.44 1.4 0.76 7.25
230 67.75 64 54 4 3 530 000 790 000 54 000 80 500 1 500 2 000 HR 32226 J 4FD 151 147 216 196 219 7 13.5 3 2.5 57.0 0.44 1.4 0.76 11.3
280 63.75 58 49 5 4 545 000 675 000 56 000 68 500 1 300 1 800 30326 157 168 262 239 255 8 14.5 4 3 53.9 0.36 1.7 0.92 16.6
280 63.75 58 49 5 4 650 000 820 000 66 000 83 500 1 300 1 800 HR 30326 J 2GB 157 166 262 241 255 8 14.5 4 3 52.8 0.35 1.7 0.96 17.2
280 72 66 44 5 4 625 000 820 000 63 500 83 500 1 200 1 700 HR 31326 J 7GB 174 159 262 220 261 9 28 4 3 87.1 0.83 0.73 0.40 18.8
280 98.75 93 78 5 4 830 000 1 150 000 84 500 117 000 1 300 1 800 32326 162 165 262 233 263 8 20.5 4 3 69.2 0.36 1.7 0.92 26.6
B 128 B 129
B110-181E.indd 128-129 11/20/13 4:57:00 PM

T Sa Sb
C
P = X Fr +Y Fa
Fa/ Fre Fa/ Fr>e
ra
r X Y X Y
B
P0 = 0.5Fr +Y0 Fa
a
140 190 32 32 25 2 1.5 206 000 390 000 21 000 39 500 1 700 2 200 HR 32928 J 2CC 152 150 180 178 184 6 7 2 1.5 33.6 0.36 1.7 0.92 2.64
210 45 45 34 2.5 2 325 000 555 000 33 000 57 000 1 600 2 200 HR 32028 XJ 4DC 155 152 200 189 202 8 11 2 2 46.6 0.46 1.3 0.72 5.32
210 56 56 44 2.5 2 410 000 770 000 42 000 78 500 1 600 2 200 HR 33028 J 2DE 155 153 198 189 202 7 12 2 2 45.5 0.36 1.7 0.92 6.74
250 45.75 42 36 4 3 390 000 515 000 40 000 52 500 1 400 1 900 HR 30228 J 4FB 161 164 236 221 234 7 9.5 3 2.5 48.9 0.44 1.4 0.76 8.74
250 71.75 68 58 4 3 610 000 915 000 62 000 93 500 1 400 1 900 HR 32228 J 4FD 161 159 236 213 238 9 13.5 3 2.5 60.5 0.44 1.4 0.76 14.3
300 67.75 62 53 5 4 740 000 945 000 75 500 96 500 1 200 1 700 HR 30328 J 2GB 167 177 282 256 273 9 14.5 4 3 55.7 0.35 1.7 0.96 21.1
300 77 70 47 5 4 695 000 955 000 71 000 97 500 1 100 1 500 HR 31328 J 7GB 184 174 282 236 280 9 30 4 3 92.9 0.83 0.73 0.40 28.5
300 107.75 102 85 5 4 985 000 1 440 000 101 000 147 000 1 200 1 600 32328 172 177 282 246 281 9 22.5 4 3 76.4 0.37 1.6 0.88 33.9
150 210 38 36 31 2.5 2 247 000 440 000 25 200 45 000 1 500 2 000 32930 165 162 200 195 201 7 7 2 2 36.7 0.33 1.8 1.0 3.8
210 38 38 30 2.5 2 281 000 520 000 28 600 53 000 1 500 2 000 HR 32930 J 2DC 165 163 198 196 202 7 8 2 2 36.5 0.33 1.8 1.0 4.05
225 48 48 36 3 2.5 375 000 650 000 38 000 66 500 1 400 2 000 HR 32030 XJ 4EC 168 164 213 202 216 8 12 2.5 2 49.8 0.46 1.3 0.72 6.6
225 59 59 46 3 2.5 435 000 805 000 44 000 82 000 1 400 2 000 HR 33030 J 2EE 168 165 213 203 217 8 13 2.5 2 48.7 0.36 1.7 0.90 8.07
270 49 45 38 4 3 485 000 665 000 49 000 67 500 1 300 1 800 HR 30230 J 2GB 171 175 256 236 250 7 11 3 2.5 51.3 0.44 1.4 0.76 11.2
270 77 73 60 4 3 705 000 1 080 000 71 500 110 000 1 300 1 800 HR 32230 J 4GD 171 171 256 228 254 8 17 3 2.5 64.7 0.44 1.4 0.76 17.8
320 72 65 55 5 4 690 000 860 000 70 000 87 500 1 100 1 500 30330 177 193 302 275 292 8 17 4 3 61.4 0.36 1.7 0.92 24.2
320 72 65 55 5 4 825 000 1 060 000 84 500 108 000 1 100 1 600 HR 30330 J 2GB 177 190 302 276 292 8 17 4 3 60.0 0.35 1.7 0.96 25
320 82 75 50 5 4 790 000 1 100 000 80 500 112 000 1 000 1 400 HR 31330 J 7GB 194 187 302 253 300 9 32 4 3 99.3 0.83 0.73 0.40 28.5
320 114 108 90 5 4 1 120 000 1 700 000 114 000 174 000 1 100 1 500 32330 182 191 302 262 297 8 24 4 3 81.5 0.37 1.6 0.88 41.4
160 220 38 38 30 2.5 2 296 000 570 000 30 000 58 000 1 400 1 900 HR 32932 J 2DC 175 173 208 206 212 7 8 2 2 38.7 0.35 1.7 0.95 4.32
240 51 51 38 3 2.5 425 000 750 000 43 500 76 500 1 300 1 800 HR 32032 XJ 4EC 178 175 228 216 231 8 13 2.5 2 53.0 0.46 1.3 0.72 7.93
290 52 48 40 4 3 530 000 730 000 54 000 74 500 1 200 1 600 HR 30232 J 4GB 181 189 276 253 269 8 12 3 2.5 55.0 0.44 1.4 0.76 13.7
290 84 80 67 4 3 795 000 1 220 000 81 000 125 000 1 200 1 600 HR 32232 J 4GD 181 184 276 243 274 10 17 3 2.5 70.5 0.44 1.4 0.76 22.7
340 75 68 58 5 4 765 000 960 000 78 000 98 000 1 000 1 400 30332 187 205 322 293 311 10 17 4 3 64.6 0.36 1.7 0.92 28.4
340 75 68 58 5 4 870 000 1 110 000 89 000 113 000 1 100 1 400 HR 30332 J 2GB 187 201 322 293 310 10 17 4 3 62.9 0.35 1.7 0.96 29.2
340 75 68 48 5 4 675 000 875 000 69 000 89 000 950 1 300 30332 D 196 198 322 270 313 9 27 4 3 99.4 0.81 0.74 0.41 27.5
340 121 114 95 5 4 1 210 000 1 770 000 123 000 181 000 1 000 1 400 32332 192 202 322 281 319 10 26 4 3 87.1 0.37 1.6 0.88 48.3
170 230 38 36 31 2.5 2.5 258 000 485 000 26 300 49 500 1 300 1 800 32934 185 183 220 216 223 7 7 2 2 41.6 0.36 1.7 0.90 4.3
230 38 38 30 2.5 2 294 000 560 000 30 000 57 000 1 400 1 800 HR 32934 J 3DC 185 180 218 215 222 7 8 2 2 41.7 0.38 1.6 0.86 4.44
260 57 57 43 3 2.5 505 000 890 000 51 500 90 500 1 200 1 700 HR 32034 XJ 4EC 188 187 248 232 249 10 14 2.5 2 56.6 0.44 1.4 0.74 10.6
310 57 52 43 5 4 630 000 885 000 64 000 90 000 1 100 1 500 HR 30234 J 4GB 197 202 292 273 288 8 14 4 3 59.4 0.44 1.4 0.76 17.1
310 91 86 71 5 4 930 000 1 450 000 94 500 148 000 1 100 1 500 HR 32234 J 4GD 197 197 292 262 294 10 20 4 3 76.4 0.44 1.4 0.76 28
360 80 72 62 5 4 845 000 1 080 000 86 000 110 000 950 1 300 30334 197 221 342 312 332 10 18 4 3 70.1 0.37 1.6 0.90 33.5
360 80 72 62 5 4 960 000 1 230 000 98 000 125 000 1 000 1 300 HR 30334 J 2GB 197 214 342 310 329 10 18 4 3 67.3 0.35 1.7 0.96 34.5
360 80 72 50 5 4 760 000 1 040 000 77 500 106 000 900 1 200 30334 D 206 215 342 288 332 10 30 4 3 107.3 0.81 0.74 0.41 33.4
360 127 120 100 5 4 1 370 000 2 050 000 140 000 209 000 1 000 1 300 32334 202 213 342 297 337 10 27 4 3 91.3 0.37 1.6 0.88 57
B 130 B 131
B110-181E.indd 130-131 11/20/13 4:57:01 PM

T Sa Sb
C
P = X Fr +Y Fa
Fa/ Fre Fa/ Fr>e
ra
r X Y X Y
B
P0 = 0.5Fr +Y0 Fa
a
180 250 45 45 34 2.5 2 350 000 685 000 36 000 69 500 1 300 1 700 HR 32936 J 4DC 195 192 240 227 241 8 11 2 2 53.9 0.48 1.3 0.69 6.56
280 64 64 48 3 2.5 640 000 1 130 000 65 000 115 000 1 200 1 600 HR 32036 XJ 3FD 198 199 268 248 267 10 16 2.5 2 60.4 0.42 1.4 0.78 14.3
320 57 52 43 5 4 650 000 930 000 66 000 95 000 1 100 1 400 HR 30236 J 4GB 207 210 302 281 297 9 14 4 3 61.8 0.45 1.3 0.73 17.8
320 91 86 71 5 4 960 000 1 540 000 98 000 157 000 1 100 1 400 HR 32236 J 4GD 207 205 302 270 303 10 20 4 3 78.9 0.45 1.3 0.73 29.8
380 83 75 64 5 4 935 000 1 230 000 95 500 126 000 900 1 300 30336 207 233 362 324 345 10 19 4 3 72.5 0.36 1.7 0.92 39.3
380 83 75 53 5 4 820 000 1 120 000 83 500 114 000 850 1 200 30336 D 216 229 362 304 352 10 30 4 3 113.1 0.81 0.74 0.41 38.5
380 134 126 106 5 4 1 520 000 2 290 000 155 000 234 000 950 1 300 32336 212 225 362 310 353 10 28 4 3 96.6 0.37 1.6 0.88 66.8
190 260 45 45 34 2.5 2 365 000 715 000 37 000 73 000 1 200 1 600 HR 32938 J 4DC 205 201 250 237 251 8 11 2 2 55.3 0.48 1.3 0.69 6.83
290 64 64 48 3 2.5 650 000 1 170 000 66 000 119 000 1 100 1 500 HR 32038 XJ 4FD 208 209 278 258 279 10 16 2.5 2 63.4 0.44 1.4 0.75 14.9
340 60 55 46 5 4 715 000 1 020 000 73 000 104 000 1 000 1 300 HR 30238 J 4GB 217 223 322 302 318 9 14 4 3 65.6 0.44 1.4 0.76 21.4
340 97 92 75 5 4 1 110 000 1 770 000 113 000 181 000 1 000 1 400 HR 32238 J 4GD 217 216 322 290 323 10 22 4 3 80.5 0.44 1.4 0.76 35.2
400 86 78 65 6 5 1 010 000 1 340 000 103 000 136 000 850 1 200 30338 223 248 378 346 366 11 21 5 4 76.1 0.36 1.7 0.92 46
400 140 132 109 6 5 1 660 000 2 580 000 169 000 263 000 850 1 200 32338 229 243 378 332 375 11 31 5 4 102.7 0.37 1.6 0.88 78.9
200 280 51 48 41 3 2.5 410 000 780 000 42 000 80 000 1 100 1 500 32940 218 217 268 256 269 9 10 2.5 2 53.4 0.37 1.6 0.88 9.26
280 51 51 39 3 2.5 480 000 935 000 48 500 95 000 1 100 1 500 HR 32940 J 3EC 218 216 268 258 271 9 12 2.5 2 54.2 0.39 1.5 0.84 9.65
310 70 70 53 3 2.5 760 000 1 370 000 77 500 139 000 1 000 1 400 HR 32040 XJ 4FD 218 221 298 277 297 11 17 2.5 2 67.4 0.43 1.4 0.77 18.9
360 64 58 48 5 4 795 000 1 120 000 81 000 114 000 950 1 300 HR 30240 J 4GB 227 236 342 318 336 10 16 4 3 69.1 0.44 1.4 0.76 25.5
360 104 98 82 5 4 1 210 000 1 920 000 123 000 196 000 950 1 300 HR 32240 J 3GD 227 230 342 305 340 11 22 4 3 85.1 0.41 1.5 0.81 42.6
420 89 80 67 6 5 1 030 000 1 390 000 105 000 142 000 850 1 200 30340 233 253 398 346 368 11 22 5 4 81.4 0.37 1.6 0.88 52.3
420 89 80 56 6 5 965 000 1 330 000 98 500 136 000 750 1 000 30340 D 244 253 398 336 385 11 33 5 4 122.9 0.81 0.74 0.41 49.6
420 146 138 115 6 5 1 820 000 2 870 000 185 000 292 000 800 1 100 32340 239 253 398 346 392 11 31 5 4 106.7 0.37 1.6 0.88 90.9
220 300 51 51 39 3 2.5 490 000 990 000 50 000 101 000 1 000 1 400 HR 32944 J 3EC 238 235 288 278 293 9 12 2.5 2 59.2 0.43 1.4 0.78 10.3
340 76 76 57 4 3 885 000 1 610 000 90 500 164 000 950 1 300 HR 32044 XJ 4FD 241 244 326 303 326 12 19 3 2.5 73.6 0.43 1.4 0.77 24.4
400 72 65 54 5 4 810 000 1 150 000 82 500 117 000 850 1 100 30244 247 267 382 350 367 11 18 4 3 74.7 0.40 1.5 0.82 33.6
400 114 108 90 5 4 1 340 000 2 210 000 137 000 225 000 850 1 100 32244 247 260 382 340 377 12 24 4 3 93.0 0.40 1.5 0.82 57.4
460 97 88 73 6 5 1 430 000 1 990 000 146 000 203 000 750 1 000 30344 253 283 438 390 414 12 24 5 4 85.4 0.36 1.7 0.92 72.4
460 154 145 122 6 5 2 020 000 3 200 000 206 000 325 000 750 1 000 32344 259 274 438 372 421 12 32 5 4 114.9 0.37 1.6 0.88 114
240 320 51 51 39 3 2.5 500 000 1 040 000 51 000 107 000 950 1 300 HR 32948 J 4EC 258 255 308 297 314 9 12 2.5 2 65.1 0.46 1.3 0.72 11.1
360 76 76 57 4 3 920 000 1 730 000 94 000 177 000 850 1 200 HR 32048 XJ 4FD 261 262 346 321 346 12 19 3 2.5 79.1 0.46 1.3 0.72 26.2
440 79 72 60 5 4 990 000 1 400 000 101 000 142 000 750 1 000 30248 267 288 422 384 408 11 19 4 3 85.1 0.44 1.4 0.74 45.2
440 127 120 100 5 4 1 630 000 2 730 000 166 000 278 000 750 1 000 32248 267 285 422 374 416 12 27 4 3 102.5 0.40 1.5 0.82 78
500 105 95 80 6 5 1 660 000 2 340 000 169 000 238 000 670 950 30348 273 308 478 422 447 12 25 5 4 92.8 0.36 1.7 0.92 92.6
500 165 155 132 6 5 2 520 000 4 100 000 257 000 415 000 670 900 32348 279 301 478 410 464 12 33 5 4 123.2 0.37 1.6 0.88 145
B 132 B 133
B110-181E.indd 132-133 11/20/13 4:57:02 PM

T Sa Sb
C
P = X Fr +Y Fa
Fa/ Fre Fa/ Fr>e
ra
r X Y X Y
B
P0 = 0.5Fr +Y0 Fa
a
260 360 63.5 63.5 48 3 2.5 730 000 1 450 000 74 500 148 000 850 1 100 HR 32952 J 3EC 278 278 348 333 347 11 15.5 2.5 2 69.8 0.41 1.5 0.81 18.6
400 87 87 65 5 4 1 160 000 2 160 000 118 000 220 000 800 1 100 HR 32052 XJ 4FC 287 287 382 357 383 14 22 4 3 86.3 0.43 1.4 0.76 38.5
480 89 80 67 6 5 1 190 000 1 700 000 121 000 174 000 670 900 30252 293 316 458 421 447 12 22 5 4 94.6 0.44 1.4 0.74 60.7
480 137 130 106 6 5 1 900 000 3 300 000 194 000 335 000 670 950 32252 293 305 458 394 446 14 31 5 4 116.0 0.45 1.3 0.73 103
540 113 102 85 6 6 1 870 000 2 640 000 190 000 269 000 630 850 30352 293 336 512 460 487 16 28 5 5 101.6 0.36 1.7 0.92 114
540 176 165 136 6 6 2 910 000 4 800 000 297 000 490 000 630 850 32352 293 328 512 441 495 13 40 5 5 130.5 0.37 1.6 0.88 188
280 380 63.5 63.5 48 3 2.5 765 000 1 580 000 78 000 162 000 800 1 100 HR 32956 J 4EC 298 297 368 352 368 12 15.5 2.5 2 75.3 0.43 1.4 0.76 20
420 87 87 65 5 4 1 180 000 2 240 000 120 000 228 000 710 1 000 HR 32056 XJ 4FC 307 305 402 374 402 14 22 4 3 91.6 0.46 1.3 0.72 40.6
500 89 80 67 6 5 1 240 000 1 900 000 127 000 194 000 630 850 30256 313 339 478 436 462 12 22 5 4 98.5 0.44 1.4 0.74 66.3
500 137 130 106 6 5 1 950 000 3 450 000 199 000 355 000 630 850 32256 313 325 478 412 467 14 31 5 4 123.1 0.47 1.3 0.70 109
580 187 175 145 6 6 3 300 000 5 400 000 335 000 550 000 560 800 32356 319 353 552 475 532 14 42 5 5 139.6 0.37 1.6 0.89 224
300 420 76 72 62 4 3 895 000 1 820 000 91 000 186 000 710 950 32960 321 326 406 386 405 13 14 3 2.5 79.3 0.37 1.6 0.88 30.5
420 76 76 57 4 3 1 010 000 2 100 000 103 000 214 000 710 950 HR 32960 J 3FD 321 324 406 387 405 13 19 3 2.5 79.9 0.39 1.5 0.84 31.4
460 100 100 74 5 4 1 440 000 2 700 000 147 000 275 000 670 900 HR 32060 XJ 4GD 327 330 442 408 439 15 26 4 3 98.4 0.43 1.4 0.76 56.6
540 96 85 71 6 5 1 440 000 2 100 000 147 000 214 000 600 800 30260 333 355 518 470 499 14 25 5 4 105.1 0.44 1.4 0.74 80.6
540 149 140 115 6 5 2 220 000 3 700 000 226 000 380 000 600 800 32260 333 352 518 458 514 15 34 5 4 131.7 0.46 1.3 0.72 132
320 440 76 72 63 4 3 900 000 1 880 000 92 000 192 000 970 900 32964 341 345 426 404 425 13 13 3 2.5 84.3 0.39 1.5 0.84 32
440 76 76 57 4 3 1 040 000 2 220 000 106 000 227 000 670 900 HR 32964 J 3FD 341 344 426 406 426 13 19 3 2.5 85.0 0.42 1.4 0.79 33.3
480 100 100 74 5 4 1 510 000 2 910 000 153 000 297 000 630 850 HR 32064 XJ 4GD 347 350 462 430 461 15 26 4 3 104.5 0.46 1.3 0.72 60
580 104 92 75 6 5 1 640 000 2 420 000 168 000 247 000 530 750 30264 353 381 558 503 533 14 29 5 4 113.7 0.44 1.4 0.74 99.3
580 159 150 125 6 5 2 860 000 5 050 000 292 000 515 000 530 750 32264 353 383 558 487 550 15 34 5 4 141.7 0.46 1.3 0.72 175
670 210 200 170 7.5 7.5 4 200 000 7 100 000 430 000 725 000 480 670 32364 383 412 634 547 616 14 42 6 6 157.5 0.37 1.6 0.88 343
340 460 76 72 63 4 3 910 000 1 940 000 93 000 197 000 630 850 32968 361 364 446 426 446 13 13 3 2.5 89.2 0.41 1.5 0.80 33.6
460 76 76 57 4 3 1 050 000 2 220 000 107 000 226 000 630 850 HR 32968 J 4FD 361 362 446 427 446 13 19 3 2.5 91.0 0.44 1.4 0.75 34.3
520 112 106 92 6 5 1 650 000 3 400 000 168 000 345 000 560 750 32068 373 386 498 464 496 3.5 22 5 4 104.5 0.37 1.6 0.89 83.7
360 480 76 72 62 4 3 945 000 2 100 000 96 500 214 000 600 800 32972 381 386 466 445 465 14 14 3 2.5 91.4 0.40 1.5 0.82 35.8
480 76 76 57 4 3 1 080 000 2 340 000 110 000 239 000 560 800 HR 32972 J 4FD 381 381 466 445 466 13 19 3 2.5 96.8 0.46 1.3 0.72 36.1
540 112 106 92 6 5 1 680 000 3 500 000 171 000 355 000 530 750 32072 393 402 518 480 514 5.5 22 5 4 108.6 0.38 1.6 0.86 86.5
380 520 87 82 71 5 4 1 210 000 2 550 000 124 000 260 000 560 750 32976 407 406 502 478 501 16 16 4 3 95.2 0.39 1.6 0.86 49.5
400 540 87 82 71 5 4 1 250 000 2 700 000 128 000 276 000 530 710 32980 427 428 522 499 524 16 16 4 3 100.8 0.40 1.5 0.82 52.7
600 125 118 100 6 5 1 960 000 4 050 000 200 000 415 000 480 670 32080 433 443 578 533 565 5 25 5 4 115.3 0.36 1.7 0.92 116
420 560 87 82 72 5 4 1 300 000 2 810 000 132 000 287 000 500 670 32984 447 448 542 521 544 3.5 15 4 3 106.1 0.41 1.5 0.81 54.8
620 125 118 100 6 5 2 000 000 4 200 000 204 000 430 000 450 630 32084 453 463 598 552 586 6.5 25 5 4 120.0 0.37 1.6 0.88 121
440 650 130 122 104 6 6 2 230 000 4 600 000 227 000 470 000 430 600 32088 473 487 622 582 616 5 26 5 5 126.3 0.36 1.7 0.92 136
B 134 B 135
B110-181E.indd 134-135 11/20/13 4:57:03 PM

SINGLE-ROW TAPERED ROLLER BEARINGS (INCH DESIGN)
T
C
r ra
P =X Fr +Y Fa
r ra Fa/ Fre Fa/ Fr>e

B X Y X Y
jD jd jDajd b jd a jD b 1 0 0.4 Y1
P0 = 0.5Fr +Y0 Fa
a given in the table below.
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers Abutment and Fillet Dimensions Eff. Load Constant Axial Load Mass
(mm) (N) {kgf} (min1) (mm) Centers Factors (kg)
Cone Cup Cone Cup (mm)
d D T B C r Cr C 0r Cr C 0r Grease Oil CONE CUP da db Da Db ra a e Y1 Y0 approx.
min. max. CONE CUP
12.000 31.991 10.008 10.785 7.938 0.8 1.3 10 300 8 900 1 050 905 13 000 18 000 *A 2047 A 2126 16.5 15.5 26 29 0.8 1.3 6.8 0.41 1.5 0.81 0.023 0.017
12.700 34.988 10.998 10.988 8.730 1.3 1.3 11 700 10 900 1 200 1 110 12 000 16 000 A 4050 A 4138 18.5 17 29 32 1.3 1.3 8.2 0.45 1.3 0.73 0.033 0.022
15.000 34.988 10.998 10.988 8.730 0.8 1.3 11 700 10 900 1 200 1 110 12 000 16 000 *A 4059 A 4138 19.5 19 29 32 0.8 1.3 8.2 0.45 1.3 0.73 0.029 0.022
15.875 34.988 10.998 10.998 8.712 1.3 1.3 13 800 13 400 1 410 1 360 11 000 15 000 L 21549 L 21511 21.5 19.5 29 32.5 1.3 1.3 7.7 0.32 1.9 1.0 0.031 0.018
39.992 12.014 11.153 9.525 1.3 1.3 14 900 15 700 1 520 1 600 9 500 13 000 A 6062 A 6157 22 20.5 34 37 1.3 1.3 10.3 0.53 1.1 0.63 0.044 0.031
41.275 14.288 14.681 11.112 1.3 2.0 21 300 19 900 2 170 2 030 10 000 13 000 03062 03162 21.5 20 34 37.5 1.3 2 9.1 0.31 1.9 1.1 0.061 0.035
42.862 14.288 14.288 9.525 1.5 1.5 17 300 17 200 1 770 1 750 8 500 12 000 11590 11520 24.5 22.5 34.5 39.5 1.5 1.5 13.0 0.70 0.85 0.47 0.061 0.040
42.862 16.670 16.670 13.495 1.5 1.5 26 900 26 300 2 750 2 680 9 500 13 000 17580 17520 23 21 36.5 39 1.5 1.5 10.6 0.33 1.8 1.0 0.075 0.048
44.450 15.494 14.381 11.430 1.5 1.5 23 800 23 900 2 430 2 440 8 500 11 000 05062 05175 23.5 21 38 42 1.5 1.5 11.2 0.36 1.7 0.93 0.081 0.039
49.225 19.845 21.539 14.288 0.8 1.3 37 500 37 000 3 800 3 800 8 500 11 000 09062 09195 22 21.5 42 44.5 0.8 1.3 10.7 0.27 2.3 1.2 0.139 0.065
16.000 47.000 21.000 21.000 16.000 1.0 2.0 35 000 36 500 3 600 3 750 9 000 12 000 *HM 81649 **HM 81610 27.5 23 37.5 43 1 2 14.9 0.55 1.1 0.60 0.115 0.082
16.993 39.992 12.014 11.153 9.525 0.8 1.3 14 900 15 700 1 520 1 600 9 500 13 000 A 6067 A 6157 22 21 34 37 0.8 1.3 10.3 0.53 1.1 0.63 0.042 0.031
17.455 36.525 11.112 11.112 7.938 1.5 1.5 11 600 11 000 1 190 1 120 10 000 14 000 A 5069 A 5144 23.5 21.5 30 33.5 1.5 1.5 8.9 0.49 1.2 0.68 0.030 0.020
17.462 39.878 13.843 14.605 10.668 1.3 1.3 22 500 22 500 2 290 2 290 10 000 13 000 LM 11749 LM 11710 23 21.5 34 37 1.3 1.3 8.7 0.29 2.1 1.2 0.055 0.028
47.000 14.381 14.381 11.112 0.8 1.3 23 800 23 900 2 430 2 440 8 500 11 000 05068 05185 23 22.5 40.5 42.5 0.8 1.3 10.1 0.36 1.7 0.93 0.082 0.047
19.050 39.992 12.014 11.153 9.525 1.0 1.3 14 900 15 700 1 520 1 600 9 500 13 000 A 6075 A 6157 24 23 34 37 1 1.3 10.3 0.53 1.1 0.63 0.037 0.031
45.237 15.494 16.637 12.065 1.3 1.3 28 500 28 900 2 910 2 950 9 000 12 000 LM 11949 LM 11910 25 23.5 39.5 41.5 1.3 1.3 9.5 0.30 2.0 1.1 0.081 0.044
47.000 14.381 14.381 11.112 1.3 1.3 23 800 23 900 2 430 2 440 8 500 11 000 05075 05185 25 23.5 40.5 42.5 1.3 1.3 10.1 0.36 1.7 0.93 0.077 0.047
49.225 18.034 19.050 14.288 1.3 1.3 37 500 37 000 3 800 3 800 8 500 11 000 09067 09195 25.5 24 42 44.5 1.3 1.3 10.7 0.27 2.3 1.2 0.115 0.065
49.225 19.845 21.539 14.288 1.2 1.3 37 500 37 000 3 800 3 800 8 500 11 000 09078 09195 25.5 24 42 44.5 1.2 1.3 10.7 0.27 2.3 1.2 0.124 0.065
49.225 21.209 19.050 17.462 1.3 1.5 37 500 37 000 3 800 3 800 8 500 11 000 09067 09196 25.5 24 41.5 44.5 1.3 1.5 13.8 0.27 2.3 1.2 0.115 0.085
49.225 23.020 21.539 17.462 C1.5 3.5 37 500 37 000 3 800 3 800 8 500 11 000 09074 09194 26 24 39 44.5 1.5 3.5 13.8 0.27 2.3 1.2 0.124 0.082
53.975 22.225 21.839 15.875 1.5 2.3 40 500 39 500 4 150 4 000 7 500 10 000 21075 21212 31.5 26 43 50 1.5 2.3 16.3 0.59 1.0 0.56 0.156 0.097
19.990 47.000 14.381 14.381 11.112 1.5 1.3 23 800 23 900 2 430 2 440 8 500 11 000 05079 05185 26.5 24 40.5 42.5 1.5 1.3 10.1 0.36 1.7 0.93 0.073 0.047
20.000 51.994 15.011 14.260 12.700 1.5 1.3 26 000 27 900 2 650 2 840 7 500 10 000 07079 07204 27.5 27 45 48 1.5 1.3 12.1 0.40 1.5 0.82 0.105 0.061
20.625 49.225 23.020 21.539 17.462 1.5 1.5 37 500 37 000 3 800 3 800 8 500 11 000 09081 09196 27.5 25.5 41.5 44.5 1.5 1.5 13.8 0.27 2.3 1.2 0.115 0.085
20.638 49.225 19.845 19.845 15.875 1.5 1.5 36 000 37 000 3 650 3 750 8 000 11 000 12580 12520 28.5 26 42.5 45.5 1.5 1.5 12.9 0.32 1.9 1.0 0.114 0.067
21.430 50.005 17.526 18.288 13.970 1.3 1.3 38 500 40 000 3 950 4 100 8 000 11 000 M 12649 M 12610 27.5 25.5 44 46 1.3 1.3 10.9 0.28 2.2 1.2 0.115 0.059
22.000 45.237 15.494 16.637 12.065 1.3 1.3 29 200 33 500 2 980 3 400 8 500 11 000 * LM 12749 LM 12710 27.5 26 39.5 42.5 1.3 1.3 10.0 0.31 2.0 1.1 0.078 0.038
45.975 15.494 16.637 12.065 1.3 1.3 29 200 33 500 2 980 3 400 8 500 11 000 * LM 12749 LM 12711 27.5 26 40 42.5 1.3 1.3 10.0 0.31 2.0 1.1 0.078 0.043
22.225 50.005 13.495 14.260 9.525 1.3 1.0 26 000 27 900 2 650 2 840 7 500 10 000 07087 07196 28.5 27 44.5 47 1.3 1 10.6 0.40 1.5 0.82 0.097 0.035
50.005 17.526 18.288 13.970 1.3 1.3 38 500 40 000 3 950 4 100 8 000 11 000 M 12648 M 12610 28.5 26.5 44 46 1.3 1.3 10.9 0.28 2.2 1.2 0.111 0.059
52.388 19.368 20.168 14.288 1.5 1.5 40 500 43 000 4 100 4 400 7 500 10 000 1380 1328 29.5 27 45 48.5 1.5 1.5 11.3 0.29 2.1 1.1 0.137 0.067
53.975 19.368 20.168 14.288 1.5 1.5 40 500 43 000 4 100 4 400 7 500 10 000 1380 1329 29.5 27 46 49 1.5 1.5 11.3 0.29 2.1 1.1 0.137 0.082
56.896 19.368 19.837 15.875 1.3 1.3 38 000 40 500 3 900 4 150 7 100 9 500 1755 1729 29 27.5 49 51 1.3 1.3 12.2 0.31 2.0 1.1 0.152 0.102
57.150 22.225 22.225 17.462 0.8 1.5 48 000 50 000 4 850 5 100 7 100 9 500 1280 1220 29.5 29 49 52 0.8 1.5 15.1 0.35 1.7 0.95 0.183 0.106
Notes * The maximum bore diameter is listed and its tolerance is negative (See Table 8.4.1 on Page A68).
** The maximum outside diameter is listed and its tolerance is negative (See Table 8.4.2 on Pages A68 and A69).
The tolerances for the bore diameter and overall bearing width differ from the standard (See Table 5 on Page B114).
* The tolerance for the bore diameter is 0 to 20 m, and for overall bearing width is +356 to 0 m.
B 136 B 137
B110-181E.indd 136-137 11/20/13 4:57:04 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
22.606 47.000 15.500 15.500 12.000 1.5 1.0 26 300 30 000 2 680 3 100 8 000 11 000 LM 72849 LM 72810 29 27 40.5 44.5 1.5 1 12.2 0.47 1.3 0.70 0.086 0.046
23.812 50.292 14.224 14.732 10.668 1.5 1.3 27 600 32 000 2 820 3 250 7 100 10 000 L 44640 L 44610 30.5 28.5 44.5 47 1.5 1.3 10.9 0.37 1.6 0.88 0.097 0.039
56.896 19.368 19.837 15.875 0.8 1.3 38 000 40 500 3 900 4 150 7 100 9 500 1779 1729 29.5 28.5 49 51 0.8 1.3 12.2 0.31 2.0 1.1 0.143 0.102
24.000 55.000 25.000 25.000 21.000 2.0 2.0 49 500 55 000 5 050 5 650 7 100 9 500 JHM 33449 JHM 33410 35 30 47 52 2 2 15.8 0.35 1.7 0.93 0.181 0.107
24.981 51.994 15.011 14.260 12.700 1.5 1.3 26 000 27 900 2 650 2 840 7 500 10 000 07098 07204 31 29 45 48 1.5 1.3 12.1 0.40 1.5 0.82 0.085 0.061
52.001 15.011 14.260 12.700 1.5 2.0 26 000 27 900 2 650 2 840 7 500 10 000 07098 07205 31 29 44.5 48 1.5 2 12.1 0.40 1.5 0.82 0.085 0.061
62.000 16.002 16.566 14.288 1.5 1.5 37 000 39 500 3 750 4 000 6 300 8 500 17098 17244 33 30.5 54 57 1.5 1.5 12.8 0.38 1.6 0.86 0.165 0.091
25.000 50.005 13.495 14.260 9.525 1.5 1.0 26 000 27 900 2 650 2 840 7 500 10 000 07097 07196 31 29 44.5 47 1.5 1 10.6 0.40 1.5 0.82 0.085 0.035
51.994 15.011 14.260 12.700 1.5 1.3 26 000 27 900 2 650 2 840 7 500 10 000 07097 07204 31 29 45 48 1.5 1.3 12.1 0.40 1.5 0.82 0.085 0.061
25.400 50.005 13.495 14.260 9.525 3.3 1.0 26 000 27 900 2 650 2 840 7 500 10 000 07100 SA 07196 35 29.5 44.5 47 3.3 1 10.6 0.40 1.5 0.82 0.082 0.035
50.005 13.495 14.260 9.525 1.0 1.0 26 000 27 900 2 650 2 840 7 500 10 000 07100 07196 30.5 29.5 44.5 47 1 1 10.6 0.40 1.5 0.82 0.084 0.035
50.292 14.224 14.732 10.668 1.3 1.3 27 600 32 000 2 820 3 250 7 100 10 000 L 44643 L 44610 31.5 29.5 44.5 47 1.3 1.3 10.9 0.37 1.6 0.88 0.090 0.039
57.150 17.462 17.462 13.495 1.3 1.5 39 500 45 500 4 050 4 650 6 700 9 000 15578 15520 32.5 30.5 51 53 1.3 1.5 12.4 0.35 1.7 0.95 0.151 0.070
57.150 19.431 19.431 14.732 1.5 1.5 42 500 49 000 4 300 5 000 6 700 9 000 M 84548 M 84510 36 33 48.5 54 1.5 1.5 16.1 0.55 1.1 0.60 0.156 0.089
59.530 23.368 23.114 18.288 0.8 1.5 50 000 58 000 5 100 5 900 6 300 9 000 M 84249 M 84210 36 32.5 49.5 56 0.8 1.5 18.3 0.55 1.1 0.60 0.194 0.13
62.000 19.050 20.638 14.288 0.8 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15101 15245 32.5 31.5 55 58 0.8 1.3 13.3 0.35 1.7 0.94 0.222 0.081
63.500 20.638 20.638 15.875 3.5 1.5 46 000 53 000 4 700 5 400 6 000 8 000 15100 15250 X 38 31.5 55 59 3.5 1.5 14.9 0.35 1.7 0.94 0.22 0.113
64.292 21.433 21.433 16.670 1.5 1.5 51 000 64 500 5 200 6 600 5 600 8 000 M 86643 M 86610 38 36.5 54 61 1.5 1.5 17.7 0.55 1.1 0.60 0.246 0.128
65.088 22.225 21.463 15.875 1.5 1.5 45 000 47 500 4 600 4 850 5 600 8 000 23100 23256 39 34.5 53 61 1.5 1.5 20.0 0.73 0.82 0.45 0.214 0.142
68.262 22.225 22.225 17.462 0.8 1.5 55 000 64 000 5 600 6 550 5 600 7 500 02473 02420 34.5 33.5 59 63 0.8 1.5 16.9 0.42 1.4 0.79 0.28 0.152
72.233 25.400 25.400 19.842 0.8 2.3 63 500 83 500 6 500 8 500 5 000 7 100 HM 88630 HM 88610 39.5 39.5 60 69 0.8 2.3 20.7 0.55 1.1 0.60 0.398 0.188
72.626 24.608 24.257 17.462 2.3 1.5 60 000 58 000 6 100 5 900 5 600 7 500 41100 41286 41 36.5 61 68 2.3 1.5 20.7 0.60 1.0 0.55 0.32 0.177
26.988 50.292 14.224 14.732 10.668 3.5 1.3 27 600 32 000 2 820 3 250 7 100 10 000 L 44649 L 44610 37.5 31 44.5 47 3.5 1.3 10.9 0.37 1.6 0.88 0.081 0.039
57.150 19.845 19.355 15.875 3.3 1.5 40 000 44 500 4 100 4 500 6 700 9 000 1997 X 1922 37.5 31.5 51 53.5 3.3 1.5 13.9 0.33 1.8 1.0 0.152 0.077
60.325 19.842 17.462 15.875 3.5 1.5 39 500 45 500 4 050 4 650 6 700 9 000 15580 15523 38.5 32 51 54 3.5 1.5 14.7 0.35 1.7 0.95 0.141 0.123
62.000 19.050 20.638 14.288 0.8 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15106 15245 33.5 33 55 58 0.8 1.3 13.3 0.35 1.7 0.94 0.211 0.081
28.575 57.150 19.845 19.355 15.875 3.5 1.5 40 000 44 500 4 100 4 500 6 700 9 000 1988 1922 39.5 33.5 51 53.5 3.5 1.5 13.9 0.33 1.8 1.0 0.141 0.077
59.131 15.875 16.764 11.811 spec. 1.3 34 500 41 500 3 550 4 200 6 300 8 500 LM 67043 LM 67010 40 33.5 52 56 3.5 1.3 12.6 0.41 1.5 0.80 0.147 0.062
62.000 19.050 20.638 14.288 3.5 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15112 15245 40 34 55 58 3.5 1.3 13.3 0.35 1.7 0.94 0.199 0.081
62.000 19.050 20.638 14.288 0.8 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15113 15245 34.5 34 55 58 0.8 1.3 13.3 0.35 1.7 0.94 0.20 0.081
64.292 21.433 21.433 16.670 1.5 1.5 51 000 64 500 5 200 6 600 5 600 8 000 M 86647 M 86610 40 38 54 61 1.5 1.5 17.7 0.55 1.1 0.60 0.223 0.128
68.262 22.225 22.225 17.462 0.8 1.5 55 000 64 000 5 600 6 550 5 600 7 500 02474 02420 36.5 36 59 63 0.8 1.5 16.9 0.42 1.4 0.79 0.257 0.152
72.626 24.608 24.257 17.462 4.8 1.5 60 000 58 000 6 100 5 900 5 600 7 500 41125 41286 48 36.5 61 68 4.8 1.5 20.7 0.60 1.0 0.55 0.292 0.177
72.626 24.608 24.257 17.462 1.5 1.5 60 000 58 000 6 100 5 900 5 600 7 500 41126 41286 41.5 36.5 61 68 1.5 1.5 20.7 0.60 1.0 0.55 0.295 0.177
73.025 22.225 22.225 17.462 0.8 3.3 54 500 64 500 5 550 6 600 5 300 7 100 02872 02820 37.5 37 62 68 0.8 3.3 18.3 0.45 1.3 0.73 0.321 0.16
Notes The tolerances for the bore diameter and overall bearing width differ from the standard (See Table 5 on Page B114).
The tolerances are listed in Tables 2, 3 and 4 on Pages B113 and B114.
B 138 B 139
B110-181E.indd 138-139 11/20/13 4:57:05 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
29.000 50.292 14.224 14.732 10.668 3.5 1.3 26 800 34 000 2 730 3 500 7 100 9 500 L 45449 L 45410 39.5 33 44.5 48 3.5 1.3 10.8 0.37 1.6 0.89 0.079 0.036
29.367 66.421 23.812 25.433 19.050 3.5 1.3 65 000 73 000 6 600 7 450 6 000 8 000 2690 2631 41 35 58 60 3.5 1.3 14.3 0.25 2.4 1.3 0.242 0.165
30.000 62.000 16.002 16.566 14.288 1.5 1.5 37 000 39 500 3 750 4 000 6 300 8 500 * 17118 17244 37 34.5 54 57 1.5 1.5 12.8 0.38 1.6 0.86 0.136 0.091
62.000 19.050 20.638 14.288 1.3 1.3 46 000 53 000 4 700 5 400 6 000 8 000 * 15117 15245 36.5 35 55 58 1.3 1.3 13.3 0.35 1.7 0.94 0.189 0.081
63.500 20.638 20.638 15.875 1.3 1.3 46 000 53 000 4 700 5 400 6 000 8 000 * 15117 15250 36.5 35 56 59 1.3 1.3 14.9 0.35 1.7 0.94 0.189 0.113
72.000 19.000 18.923 15.875 1.5 1.5 52 000 56 000 5 300 5 700 5 600 7 500 * 26118 26283 38 36 62 65 1.5 1.5 14.8 0.36 1.7 0.92 0.225 0.163
30.112 62.000 19.050 20.638 14.288 0.8 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15116 15245 36 35.5 55 58 0.8 1.3 13.3 0.35 1.7 0.94 0.189 0.081
30.162 58.738 14.684 15.080 10.716 3.5 1.0 28 800 33 500 2 940 3 450 6 000 8 000 08118 08231 41.5 35 52 55 3.5 1 13.3 0.47 1.3 0.70 0.12 0.057
64.292 21.433 21.433 16.670 1.5 1.5 51 000 64 500 5 200 6 600 5 600 8 000 M 86649 M 86610 41 38 54 61 1.5 1.5 17.7 0.55 1.1 0.60 0.211 0.128
68.262 22.225 22.225 17.462 2.3 1.5 55 500 70 500 5 650 7 200 5 300 7 500 M 88043 M 88010 43.5 39.5 58 65 2.3 1.5 19.1 0.55 1.1 0.60 0.263 0.146
69.850 23.812 25.357 19.050 2.3 1.3 71 000 84 000 7 200 8 550 5 600 7 500 2558 2523 40 36.5 61 64 2.3 1.3 14.5 0.27 2.2 1.2 0.297 0.169
69.850 23.812 25.357 19.050 0.8 1.3 71 000 84 000 7 200 8 550 5 600 7 500 2559 2523 37 36.5 61 64 0.8 1.3 14.5 0.27 2.2 1.2 0.298 0.169
76.200 24.608 24.074 16.670 1.5 C3.3 67 500 69 500 6 850 7 100 5 000 6 700 43118 43300 45 42 64 73 1.5 3.3 22.9 0.67 0.90 0.49 0.383 0.146
30.213 62.000 19.050 20.638 14.288 3.5 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15118 15245 41.5 35.5 55 58 3.5 1.3 13.3 0.35 1.7 0.94 0.186 0.081
62.000 19.050 20.638 14.288 0.8 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15120 15245 36 35.5 55 58 0.8 1.3 13.3 0.35 1.7 0.94 0.188 0.081
62.000 19.050 20.638 14.288 1.5 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15119 15245 37.5 35.5 55 58 1.5 1.3 13.3 0.35 1.7 0.94 0.188 0.081
30.955 64.292 21.433 21.433 16.670 1.5 1.5 51 000 64 500 5 200 6 600 5 600 8 000 M 86648 A M 86610 42 38 54 61 1.5 1.5 17.7 0.55 1.1 0.60 0.205 0.128
31.750 58.738 14.684 15.080 10.716 1.0 1.0 28 800 33 500 2 940 3 450 6 000 8 000 08125 08231 37.5 36 52 55 1 1 13.3 0.47 1.3 0.70 0.113 0.057
59.131 15.875 16.764 11.811 spec. 1.3 34 500 41 500 3 550 4 200 6 300 8 500 LM 67048 LM 67010 42.5 36 52 56 3.5 1.3 12.6 0.41 1.5 0.80 0.127 0.062
62.000 18.161 19.050 14.288 spec. 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15123 15245 42.5 36.5 55 58 3.5 1.3 13.3 0.35 1.7 0.94 0.165 0.081
62.000 19.050 20.638 14.288 0.8 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15126 15245 37 36.5 55 58 0.8 1.3 13.3 0.35 1.7 0.94 0.176 0.081
62.000 19.050 20.638 14.288 3.5 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15125 15245 42.5 36.5 55 58 3.5 1.3 13.3 0.35 1.7 0.94 0.174 0.081
63.500 20.638 20.638 15.875 0.8 1.3 46 000 53 000 4 700 5 400 6 000 8 000 15126 15250 37 36.5 56 59 0.8 1.3 14.9 0.35 1.7 0.94 0.176 0.113
68.262 22.225 22.225 17.462 3.5 1.5 55 000 64 000 5 600 6 550 5 600 7 500 02475 02420 44.5 38.5 59 63 3.5 1.5 16.9 0.42 1.4 0.79 0.229 0.152
68.262 22.225 22.225 17.462 1.5 1.5 55 500 70 500 5 650 7 200 5 300 7 500 M 88046 M 88010 43 40.5 58 65 1.5 1.5 19.1 0.55 1.1 0.60 0.25 0.146
69.012 19.845 19.583 15.875 3.5 1.3 47 000 56 000 4 800 5 700 5 600 7 500 14125 A 14276 44 37.5 60 63 3.5 1.3 15.3 0.38 1.6 0.86 0.219 0.135
69.012 26.982 26.721 15.875 4.3 3.3 47 000 56 000 4 800 5 700 5 600 7 500 14123 A 14274 41.5 37.5 59 63 4.3 3.3 15.1 0.38 1.6 0.87 0.289 0.132
69.850 23.812 25.357 19.050 0.8 1.3 71 000 84 000 7 200 8 550 5 600 7 500 2580 2523 38.5 37.5 61 64 0.8 1.3 14.5 0.27 2.2 1.2 0.282 0.169
69.850 23.812 25.357 19.050 3.5 1.3 71 000 84 000 7 200 8 550 5 600 7 500 2582 2523 44 37.5 61 64 3.5 1.3 14.5 0.27 2.2 1.2 0.28 0.169
72.626 30.162 29.997 23.812 0.8 3.3 79 500 90 000 8 100 9 200 5 300 7 500 3188 3120 39.5 39.5 61 67 0.8 3.3 19.6 0.33 1.8 0.99 0.368 0.225
73.025 29.370 27.783 23.020 1.3 3.3 74 000 100 000 7 550 10 200 5 000 7 100 HM 88542 HM 88510 45.5 42.5 59 70 1.3 3.3 23.5 0.55 1.1 0.60 0.379 0.242
80.000 21.000 22.403 17.826 0.8 1.3 68 500 75 500 6 950 7 700 4 500 6 300 346 332 40 39.5 73 75 0.8 1.3 14.6 0.27 2.2 1.2 0.419 0.146
32.000 72.233 25.400 25.400 19.842 3.3 2.3 63 500 83 500 6 500 8 500 5 000 7 100 *HM 88638 HM 88610 48.5 42.5 60 69 3.3 2.3 20.7 0.55 1.1 0.60 0.337 0.188
B 140 B 141
B110-181E.indd 140-141 11/20/13 4:57:06 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
33.338 66.675 20.638 20.638 15.875 3.5 1.5 46 000 53 500 4 650 5 450 5 600 7 500 1680 1620 44.5 38.5 58 61 3.5 1.5 15.2 0.37 1.6 0.89 0.196 0.121
68.262 22.225 22.225 17.462 0.8 1.5 55 500 70 500 5 650 7 200 5 300 7 500 M 88048 M 88010 42.5 41 58 65 0.8 1.5 19.0 0.55 1.1 0.60 0.236 0.146
69.012 19.845 19.583 15.875 3.5 3.3 47 000 56 000 4 800 5 700 5 600 7 500 14130 14274 45 38.5 59 63 3.5 3.3 15.3 0.38 1.6 0.86 0.207 0.132
69.012 19.845 19.583 15.875 0.8 1.3 47 000 56 000 4 800 5 700 5 600 7 500 14131 14276 39.5 38.5 60 63 0.8 1.3 15.3 0.38 1.6 0.86 0.209 0.135
69.850 23.812 25.357 19.050 3.5 1.3 71 000 84 000 7 200 8 550 5 600 7 500 2585 2523 45 39 61 64 3.5 1.3 14.5 0.27 2.2 1.2 0.263 0.169
72.000 19.000 18.923 15.875 3.5 1.5 52 000 56 000 5 300 5 700 5 600 7 500 26131 26283 44.5 38.5 62 65 3.5 1.5 14.7 0.36 1.7 0.92 0.20 0.163
72.626 30.162 29.997 23.812 0.8 3.3 79 500 90 000 8 100 9 200 5 300 7 500 3197 3120 41.5 40.5 61 67 0.8 3.3 19.6 0.33 1.8 0.99 0.348 0.225
73.025 29.370 27.783 23.020 0.8 3.3 74 000 100 000 7 550 10 200 5 000 7 100 HM 88547 HM 88510 45.5 42.5 59 70 0.8 3.3 23.5 0.55 1.1 0.60 0.362 0.242
76.200 29.370 28.575 23.020 3.8 0.8 78 500 106 000 8 000 10 800 4 800 6 700 HM 89444 HM 89411 53 44.5 65 73 3.8 0.8 23.6 0.55 1.1 0.60 0.419 0.261
76.200 29.370 28.575 23.020 0.8 3.3 78 500 106 000 8 000 10 800 4 800 6 700 HM 89443 HM 89410 46.5 44.5 62 73 0.8 3.3 23.6 0.55 1.1 0.60 0.421 0.257
79.375 25.400 24.074 17.462 3.5 1.5 67 500 69 500 6 850 7 100 5 000 6 700 43131 43312 51 42 67 74 3.5 1.5 23.7 0.67 0.90 0.49 0.348 0.22
34.925 65.088 18.034 18.288 13.970 spec. 1.3 47 500 57 500 4 850 5 900 5 600 7 500 LM 48548 LM 48510 46 40 58 61 3.5 1.3 14.1 0.38 1.6 0.88 0.172 0.087
65.088 20.320 18.288 16.256 spec. 1.3 47 500 57 500 4 850 5 900 5 600 7 500 LM 48548 LM 48511 46 40 58 61 3.5 1.3 16.4 0.38 1.6 0.88 0.172 0.108
66.675 20.638 20.638 16.670 3.5 2.3 53 000 62 500 5 400 6 400 5 600 7 500 M 38549 M 38510 46.5 40 58 62 3.5 2.3 15.2 0.35 1.7 0.94 0.194 0.112
69.012 19.845 19.583 15.875 3.5 1.3 47 000 56 000 4 800 5 700 5 600 7 500 14138 A 14276 46 40 60 63 3.5 1.3 15.3 0.38 1.6 0.86 0.194 0.135
69.012 19.845 19.583 15.875 1.5 1.3 47 000 56 000 4 800 5 700 5 600 7 500 14137 A 14276 42 40 60 63 1.5 1.3 15.1 0.38 1.6 0.86 0.196 0.135
72.233 25.400 25.400 19.842 2.3 2.3 63 500 83 500 6 500 8 500 5 000 7 100 HM 88649 HM 88610 48.5 42.5 60 69 2.3 2.3 20.7 0.55 1.1 0.60 0.307 0.188
73.025 22.225 22.225 17.462 0.8 3.3 54 500 64 500 5 550 6 600 5 300 7 100 02878 02820 42.5 42 62 68 0.8 3.3 18.3 0.45 1.3 0.73 0.266 0.16
73.025 22.225 23.812 17.462 3.5 3.3 63 500 77 000 6 500 7 850 5 300 7 100 2877 2820 47 41.5 63 68 3.5 3.3 16.1 0.37 1.6 0.90 0.291 0.15
73.025 23.812 24.608 19.050 1.5 0.8 71 000 86 000 7 250 8 750 5 300 7 100 25877 25821 43 40.5 65 68 1.5 0.8 15.7 0.29 2.1 1.1 0.306 0.167
73.025 23.812 24.608 19.050 3.5 2.3 71 000 86 000 7 250 8 750 5 300 7 100 25878 25820 47 40.5 64 68 3.5 2.3 15.7 0.29 2.1 1.1 0.304 0.165
76.200 29.370 28.575 23.020 0.8 0.8 78 500 106 000 8 000 10 800 4 800 6 700 HM 89446 A HM 89411 47.5 44.5 65 73 0.8 0.8 23.6 0.55 1.1 0.60 0.403 0.261
76.200 29.370 28.575 23.020 3.5 0.8 78 500 106 000 8 000 10 800 4 800 6 700 HM 89446 HM 89411 53 44.5 65 73 3.5 0.8 23.6 0.55 1.1 0.60 0.40 0.261
76.200 29.370 28.575 23.020 3.5 3.3 78 500 106 000 8 000 10 800 4 800 6 700 HM 89446 HM 89410 53 44.5 62 73 3.5 3.3 23.6 0.55 1.1 0.60 0.40 0.257
76.200 29.370 28.575 23.812 1.5 3.3 80 500 96 500 8 200 9 850 5 000 6 700 31594 31520 46 43.5 64 72 1.5 3.3 21.6 0.40 1.5 0.82 0.404 0.235
79.375 29.370 29.771 23.812 3.5 3.3 88 000 106 000 8 950 10 800 4 800 6 700 3478 3420 50 43.5 67 74 3.5 3.3 20.0 0.37 1.6 0.90 0.448 0.259
34.976 68.262 15.875 16.520 11.908 1.5 1.5 45 000 53 500 4 600 5 450 5 300 7 100 19138 19268 42.5 40.5 61 65 1.5 1.5 14.5 0.44 1.4 0.74 0.196 0.073
72.085 22.385 19.583 18.415 1.3 2.3 47 000 56 000 4 800 5 700 5 600 7 500 14139 14283 41.5 40 60 65 1.3 2.3 17.7 0.38 1.6 0.87 0.198 0.21
80.000 21.006 20.940 15.875 1.5 1.5 56 500 64 500 5 750 6 600 5 000 6 700 28138 28315 43.5 41 69 73 1.5 1.5 16.0 0.40 1.5 0.82 0.308 0.199
35.000 59.131 15.875 16.764 11.938 spec. 1.3 35 000 47 000 3 550 4 750 6 000 8 000 * L 68149 L 68110 45.5 39 52 56 3.5 1.3 13.2 0.42 1.4 0.79 0.117 0.056
59.975 15.875 16.764 11.938 spec. 1.3 35 000 47 000 3 550 4 750 6 000 8 000 * L 68149 L 68111 45.5 39 53 56 3.5 1.3 13.2 0.42 1.4 0.79 0.117 0.064
62.000 16.700 17.000 13.600 spec. 1.0 38 000 50 000 3 900 5 100 5 600 8 000 * LM 78349 ** LM 78310 46 40 55 59 3.5 1 14.4 0.44 1.4 0.74 0.137 0.074
62.000 16.700 17.000 13.600 spec. 1.5 38 000 50 000 3 900 5 100 5 600 8 000 * LM 78349 ** LM 78310 A 46 40 54 59 3.5 1.5 14.4 0.44 1.4 0.74 0.138 0.073
65.987 20.638 20.638 16.670 3.5 2.3 53 000 62 500 5 400 6 400 5 600 7 500 M 38547 M 38511 46 39.5 59 61 3.5 2.3 15.2 0.35 1.7 0.94 0.193 0.103
73.025 26.988 26.975 22.225 3.5 0.8 75 500 88 500 7 650 9 050 5 300 7 500 23691 23621 49 42 63 68 3.5 0.8 18.1 0.37 1.6 0.89 0.309 0.212
* The tolerance for the bore diameter is 0 to 20 m, and for overall bearing width is +356 to 0 m.
B 142 B 143
B110-181E.indd 142-143 11/20/13 4:57:07 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
35.717 72.233 25.400 25.400 19.842 3.5 2.3 63 500 83 500 6 500 8 500 5 000 7 100 HM 88648 HM 88610 52 43 60 69 3.5 2.3 20.7 0.55 1.1 0.60 0.298 0.188
36.487 73.025 23.812 24.608 19.050 1.5 0.8 71 000 86 000 7 250 8 750 5 300 7 100 25880 25821 44 42 65 68 1.5 0.8 15.7 0.29 2.1 1.1 0.291 0.167
36.512 76.200 29.370 28.575 23.020 3.5 3.3 78 500 106 000 8 000 10 800 4 800 6 700 HM 89449 HM 89410 54 44.5 62 73 3.5 3.3 23.6 0.55 1.1 0.60 0.38 0.257
79.375 29.370 29.771 23.812 0.8 3.3 88 000 106 000 8 950 10 800 4 800 6 700 3479 3420 45.5 44.5 67 74 0.8 3.3 20.0 0.37 1.6 0.90 0.429 0.259
88.501 25.400 23.698 17.462 2.3 1.5 73 000 81 000 7 450 8 250 4 000 5 600 44143 44348 54 50 75 84 2.3 1.5 27.9 0.78 0.77 0.42 0.502 0.245
93.662 31.750 31.750 26.195 1.5 3.3 110 000 142 000 11 200 14 400 4 000 5 600 46143 46368 48.5 46.5 79 87 1.5 3.3 24.0 0.40 1.5 0.82 0.765 0.405
38.000 63.000 17.000 17.000 13.500 spec. 1.3 38 500 52 000 3 900 5 300 5 600 7 500 JL 69349 JL 69310 49 42.5 56 60 3.5 1.3 14.6 0.42 1.4 0.79 0.132 0.071
38.100 63.500 12.700 11.908 9.525 1.5 0.8 24 100 30 500 2 460 3 100 5 300 7 100 13889 13830 45 42.5 59 60 1.5 0.8 11.9 0.35 1.7 0.95 0.109 0.046
65.088 18.034 18.288 13.970 2.3 1.3 42 500 55 000 4 300 5 650 5 300 7 500 LM 29749 LM 29710 46 42.5 59 62 2.3 1.3 13.7 0.33 1.8 0.99 0.16 0.079
65.088 18.034 18.288 13.970 spec. 1.3 42 500 55 000 4 300 5 650 5 300 7 500 LM 29748 LM 29710 49 42.5 59 62 3.5 1.3 13.7 0.33 1.8 0.99 0.158 0.079
65.088 19.812 18.288 15.748 2.3 1.3 42 500 55 000 4 300 5 650 5 300 7 500 LM 29749 LM 29711 46 42.5 58 62 2.3 1.3 15.5 0.33 1.8 0.99 0.16 0.094
68.262 15.875 16.520 11.908 1.5 1.5 45 000 53 500 4 600 5 450 5 300 7 100 19150 19268 45 43 61 65 1.5 1.5 14.5 0.44 1.4 0.74 0.173 0.073
69.012 19.050 19.050 15.083 2.0 2.3 49 000 61 000 4 950 6 250 5 300 7 100 13687 13621 46.5 43 61 65 2 2.3 15.8 0.40 1.5 0.82 0.193 0.104
69.012 19.050 19.050 15.083 3.5 0.8 49 000 61 000 4 950 6 250 5 300 7 100 13685 13620 49.5 43 62 65 3.5 0.8 15.8 0.40 1.5 0.82 0.191 0.105
72.238 20.638 20.638 15.875 3.5 1.3 48 500 59 500 4 950 6 050 5 300 7 100 16150 16284 49.5 43 63 67 3.5 1.3 16.0 0.40 1.5 0.82 0.212 0.146
73.025 23.812 25.654 19.050 3.5 0.8 73 500 91 000 7 500 9 300 5 000 6 700 2788 2735 X 50 43.5 66 69 3.5 0.8 15.9 0.30 2.0 1.1 0.312 0.135
76.200 23.812 25.654 19.050 3.5 3.3 73 500 91 000 7 500 9 300 5 000 6 700 2788 2720 50 43.5 66 70 3.5 3.3 15.9 0.30 2.0 1.1 0.312 0.187
76.200 23.812 25.654 19.050 3.5 0.8 73 500 91 000 7 500 9 300 5 000 6 700 2788 2729 50 43.5 68 70 3.5 0.8 15.9 0.30 2.0 1.1 0.312 0.191
79.375 29.370 29.771 23.812 3.5 3.3 88 000 106 000 8 950 10 800 4 800 6 700 3490 3420 52 45.5 67 74 3.5 3.3 20.0 0.37 1.6 0.90 0.404 0.259
80.035 24.608 23.698 18.512 0.8 1.5 69 000 84 500 7 000 8 600 4 500 6 300 27880 27820 48 47 68 75 0.8 1.5 21.5 0.56 1.1 0.59 0.362 0.209
82.550 29.370 28.575 23.020 0.8 3.3 87 000 117 000 8 850 11 900 4 500 6 000 HM 801346 HM 801310 51 49 68 78 0.8 3.3 24.2 0.55 1.1 0.60 0.483 0.282
88.501 25.400 23.698 17.462 2.3 1.5 73 000 81 000 7 450 8 250 4 000 5 600 44150 44348 55 51 75 84 2.3 1.5 27.9 0.78 0.77 0.42 0.484 0.245
88.501 26.988 29.083 22.225 3.5 1.5 96 500 109 000 9 800 11 100 4 500 6 000 418 414 51 44.5 77 80 3.5 1.5 17.1 0.26 2.3 1.3 0.50 0.329
95.250 30.958 28.301 20.638 1.5 0.8 87 500 97 000 8 950 9 850 3 600 5 300 53150 53375 55 53 81 89 1.5 0.8 30.7 0.74 0.81 0.45 0.665 0.365
39.688 73.025 25.654 22.098 21.336 0.8 2.3 62 500 80 000 6 400 8 150 5 000 6 700 M 201047 M 201011 45.5 48 64 69 0.8 2.3 19.7 0.33 1.8 0.99 0.266 0.169
76.200 23.812 25.654 19.050 3.5 3.3 73 500 91 000 7 500 9 300 5 000 6 700 2789 2720 52 45 66 70 3.5 3.3 15.9 0.30 2.0 1.1 0.292 0.187
80.167 29.370 30.391 23.812 0.8 3.3 92 500 108 000 9 450 11 000 4 800 6 300 3386 3320 46.5 45.5 70 75 0.8 3.3 18.4 0.27 2.2 1.2 0.442 0.217
40.000 80.000 21.000 22.403 17.826 3.5 1.3 68 500 75 500 6 950 7 700 4 500 6 300 344 332 52 45.5 73 75 3.5 1.3 14.5 0.27 2.2 1.2 0.338 0.146
80.000 21.000 22.403 17.826 0.8 1.3 68 500 75 500 6 950 7 700 4 500 6 300 344 A 332 46 45.5 73 75 0.8 1.3 14.5 0.27 2.2 1.2 0.339 0.146
88.501 25.400 23.698 17.462 2.3 1.5 73 000 81 000 7 450 8 250 4 000 5 600 44157 44348 56 51 75 84 2.3 1.5 27.9 0.78 0.77 0.42 0.463 0.245
41.000 68.000 17.500 18.000 13.500 spec. 1.5 43 500 58 000 4 450 5 950 5 300 7 100 * LM 300849 ** LM 300811 52 45 61 65 3.5 1.5 13.9 0.35 1.7 0.95 0.16 0.082
41.275 73.025 16.667 17.462 12.700 3.5 1.5 44 500 54 000 4 550 5 500 4 800 6 700 18590 18520 53 46 66 69 3.5 1.5 14.0 0.35 1.7 0.94 0.199 0.086
73.431 19.558 19.812 14.732 3.5 0.8 54 500 67 000 5 550 6 850 4 800 6 700 LM 501349 LM 501310 53 46.5 67 70 3.5 0.8 16.3 0.40 1.5 0.83 0.226 0.108
73.431 21.430 19.812 16.604 3.5 0.8 54 500 67 000 5 550 6 850 4 800 6 700 LM 501349 LM 501314 53 46.5 66 70 3.5 0.8 18.2 0.40 1.5 0.83 0.226 0.129
B 144 B 145
B110-181E.indd 144-145 11/20/13 4:57:08 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
41.275 76.200 18.009 17.384 14.288 1.5 1.5 42 500 51 000 4 350 5 200 4 500 6 300 11162 11300 49 46.5 67 71 1.5 1.5 17.4 0.49 1.2 0.68 0.212 0.129
76.200 22.225 23.020 17.462 3.5 0.8 66 000 82 000 6 700 8 400 4 800 6 700 24780 24720 53 47.5 68 72 3.5 0.8 17.0 0.39 1.5 0.84 0.279 0.15
76.200 25.400 23.020 20.638 3.5 2.3 66 000 82 000 6 700 8 400 4 800 6 700 24780 24721 54 47 66 72 3.5 2.3 20.2 0.39 1.5 0.84 0.279 0.189
79.375 23.812 25.400 19.050 3.5 0.8 77 000 98 500 7 850 10 000 4 800 6 300 26882 26822 54 47 71 74 3.5 0.8 16.4 0.32 1.9 1.0 0.349 0.186
80.000 21.000 22.403 17.826 0.8 1.3 68 500 75 500 6 950 7 700 4 500 6 300 336 332 47 46 73 75 0.8 1.3 14.5 0.27 2.2 1.2 0.325 0.146
80.000 21.000 22.403 17.826 3.5 1.3 68 500 75 500 6 950 7 700 4 500 6 300 342 332 53 46 73 75 3.5 1.3 14.5 0.27 2.2 1.2 0.323 0.146
80.167 25.400 25.400 20.638 3.5 3.3 77 000 98 500 7 850 10 000 4 800 6 300 26882 26820 54 47 69 74 3.5 3.3 18.0 0.32 1.9 1.0 0.349 0.219
82.550 26.543 25.654 20.193 3.5 3.3 78 500 102 000 8 000 10 400 4 300 6 000 M 802048 M 802011 57 51 70 79 3.5 3.3 22.9 0.55 1.1 0.60 0.406 0.23
85.725 30.162 30.162 23.812 3.5 3.3 91 000 115 000 9 300 11 700 4 300 6 000 3877 3820 57 50 73 81 3.5 3.3 21.8 0.40 1.5 0.82 0.506 0.285
87.312 30.162 30.886 23.812 0.8 3.3 96 000 120 000 9 800 12 200 4 300 6 000 3576 3525 49 48 75 81 0.8 3.3 19.5 0.31 2.0 1.1 0.532 0.304
88.501 25.400 23.698 17.462 2.3 1.5 73 000 81 000 7 450 8 250 4 000 5 600 44162 44348 57 51 75 84 2.3 1.5 28.0 0.78 0.77 0.42 0.447 0.245
88.900 30.162 29.370 23.020 3.5 3.3 96 500 129 000 9 800 13 200 4 000 5 600 HM 803146 HM 803110 60 53 74 85 3.5 3.3 25.6 0.55 1.1 0.60 0.579 0.322
88.900 30.162 29.370 23.020 0.8 3.3 96 500 129 000 9 800 13 200 4 000 5 600 HM 803145 HM 803110 54 53 74 85 0.8 3.3 25.6 0.55 1.1 0.60 0.582 0.322
90.488 39.688 40.386 33.338 3.5 3.3 139 000 180 000 14 200 18 400 4 300 5 600 4388 4335 57 51 77 85 3.5 3.3 24.6 0.28 2.1 1.2 0.789 0.459
93.662 31.750 31.750 26.195 0.8 3.3 110 000 142 000 11 200 14 400 4 000 5 600 46162 46368 52 51 79 87 0.8 3.3 24.0 0.40 1.5 0.82 0.695 0.405
95.250 30.162 29.370 23.020 3.5 3.3 106 000 143 000 10 800 14 500 3 800 5 300 HM 804840 HM 804810 61 54 81 91 3.5 3.3 26.1 0.55 1.1 0.60 0.726 0.354
98.425 30.958 28.301 20.638 1.5 0.8 87 500 97 000 8 950 9 850 3 600 5 300 53162 53387 57 53 82 91 1.5 0.8 30.7 0.74 0.81 0.45 0.618 0.442
42.862 76.992 17.462 17.145 11.908 1.5 1.5 44 000 54 000 4 450 5 500 4 500 6 000 12168 12303 51 48.5 68 73 1.5 1.5 17.7 0.51 1.2 0.65 0.228 0.098
82.550 19.842 19.837 15.080 2.3 1.5 58 500 69 000 5 950 7 050 4 500 6 300 22168 22325 52 48.5 73 76 2.3 1.5 17.6 0.43 1.4 0.77 0.283 0.176
82.931 23.812 25.400 19.050 2.3 0.8 76 500 99 000 7 800 10 100 4 500 6 000 25578 25520 53 49.5 74 77 2.3 0.8 17.6 0.33 1.8 0.99 0.383 0.203
82.931 26.988 25.400 22.225 2.3 2.3 76 500 99 000 7 800 10 100 4 500 6 000 25578 25523 53 49.5 72 77 2.3 2.3 20.8 0.33 1.8 0.99 0.383 0.248
42.875 76.200 25.400 25.400 20.638 3.5 1.5 77 000 98 500 7 850 10 000 4 800 6 300 26884 26823 55 48.5 69 73 3.5 1.5 18.0 0.32 1.9 1.0 0.337 0.136
80.000 21.000 22.403 17.826 3.5 1.3 68 500 75 500 6 950 7 700 4 500 6 300 342 S 332 54 47.5 73 75 3.5 1.3 14.5 0.27 2.2 1.2 0.305 0.146
82.931 26.988 25.400 22.225 3.5 2.3 76 500 99 000 7 800 10 100 4 500 6 000 25577 25523 55 49 72 77 3.5 2.3 20.8 0.33 1.8 0.99 0.381 0.248
83.058 23.812 25.400 19.050 3.5 3.3 76 500 99 000 7 800 10 100 4 500 6 000 25577 25521 55 49 72 77 3.5 3.3 17.6 0.33 1.8 0.99 0.381 0.201
43.000 74.988 19.368 19.837 14.288 1.5 1.3 52 500 68 000 5 350 6 900 4 800 6 300 * 16986 16929 51 48.5 67 71 1.5 1.3 17.2 0.44 1.4 0.74 0.24 0.106
44.450 80.962 19.050 17.462 14.288 0.3 1.5 45 000 57 000 4 600 5 800 4 300 6 000 13175 13318 50 50 72 76 0.3 1.5 20.1 0.53 1.1 0.63 0.252 0.144
82.931 23.812 25.400 19.050 3.5 0.8 76 500 99 000 7 800 10 100 4 500 6 000 25580 25520 57 50 74 77 3.5 0.8 17.6 0.33 1.8 0.99 0.359 0.203
83.058 23.812 25.400 19.050 3.5 3.3 76 500 99 000 7 800 10 100 4 500 6 000 25580 25521 56 51 72 78 3.5 3.3 17.6 0.33 1.8 0.99 0.359 0.201
87.312 30.162 30.886 23.812 3.5 3.3 96 000 120 000 9 800 12 200 4 300 6 000 3578 3525 57 51 75 81 3.5 3.3 19.5 0.31 2.0 1.1 0.477 0.304
88.900 30.162 29.370 23.020 3.5 3.3 96 500 129 000 9 800 13 200 4 000 5 600 HM 803149 HM 803110 62 53 74 85 3.5 3.3 25.6 0.55 1.1 0.60 0.528 0.322
93.264 30.162 30.302 23.812 3.5 3.2 103 000 136 000 10 500 13 900 3 800 5 300 3782 3720 58 52 82 88 3.5 3.2 22.4 0.34 1.8 0.97 0.678 0.292
93.662 31.750 31.750 25.400 0.8 3.3 120 000 147 000 12 200 15 000 4 000 5 600 49176 49368 54 53 82 87 0.8 3.3 21.6 0.36 1.7 0.92 0.648 0.371
93.662 31.750 31.750 25.400 3.5 3.3 120 000 147 000 12 200 15 000 4 000 5 600 49175 49368 59 53 82 87 3.5 3.3 21.6 0.36 1.7 0.92 0.645 0.371
93.662 31.750 31.750 26.195 3.5 3.3 110 000 142 000 11 200 14 400 4 000 5 600 46176 46368 60 54 79 87 3.5 3.3 24.0 0.40 1.5 0.82 0.635 0.405
95.250 27.783 29.901 22.225 3.5 2.3 106 000 126 000 10 800 12 900 4 300 5 600 438 432 57 51 83 87 3.5 2.3 18.6 0.28 2.1 1.2 0.555 0.384
Note * The maximum bore diameter is listed and its tolerance is negative (See Table 8.4.1 on Page A68).
B 146 B 147
B110-181E.indd 146-147 11/20/13 4:57:09 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
44.450 95.250 30.162 29.370 23.020 3.5 3.3 106 000 143 000 10 800 14 500 3 800 5 300 HM 804843 HM 804810 63 57 81 91 3.5 3.3 26.1 0.55 1.1 0.60 0.677 0.354
95.250 30.958 28.301 20.638 3.5 0.8 87 500 97 000 8 950 9 850 3 600 5 300 53177 53375 63 53 81 89 3.5 0.8 30.7 0.74 0.81 0.45 0.572 0.365
95.250 30.958 28.301 20.638 1.3 0.8 87 500 97 000 8 950 9 850 3 600 5 300 53176 53375 59 53 81 89 1.3 0.8 30.7 0.74 0.81 0.45 0.574 0.365
95.250 30.958 28.301 20.638 2.0 0.8 87 500 97 000 8 950 9 850 3 600 5 300 53178 53375 60 53 81 89 2 0.8 30.7 0.74 0.81 0.45 0.574 0.365
95.250 30.958 28.301 22.225 1.3 0.8 100 000 122 000 10 200 12 500 3 600 5 000 HM 903247 HM 903210 61 54 81 91 1.3 0.8 31.5 0.74 0.81 0.45 0.651 0.389
95.250 30.958 28.575 22.225 3.5 0.8 100 000 122 000 10 200 12 500 3 600 5 000 HM 903249 HM 903210 65 54 81 91 3.5 0.8 31.5 0.74 0.81 0.45 0.635 0.389
98.425 30.958 28.301 20.638 3.5 0.8 87 500 97 000 8 950 9 850 3 600 5 300 53177 53387 63 53 82 91 3.5 0.8 30.7 0.74 0.81 0.45 0.568 0.442
103.188 43.658 44.475 36.512 1.3 3.3 178 000 238 000 18 100 24 300 3 800 5 000 5356 5335 58 56 89 97 1.3 3.3 27.0 0.30 2.0 1.1 1.23 0.637
104.775 36.512 36.512 28.575 3.5 3.3 139 000 192 000 14 200 19 600 3 400 4 800 HM 807040 HM 807010 66 59 89 100 3.5 3.3 29.7 0.49 1.2 0.68 1.14 0.502
107.950 27.783 29.317 22.225 3.5 0.8 116 000 149 000 11 800 15 200 3 400 4 800 460 453 A 60 54 97 100 3.5 0.8 20.7 0.34 1.8 0.98 0.93 0.42
111.125 30.162 26.909 20.638 3.5 3.3 92 500 110 000 9 450 11 200 3 200 4 300 55175 55437 67 60 92 105 3.5 3.3 37.3 0.88 0.68 0.37 0.867 0.514
114.300 44.450 44.450 34.925 3.5 3.3 172 000 205 000 17 500 20 900 3 600 4 800 65385 65320 65 59 97 107 3.5 3.3 32.2 0.43 1.4 0.77 1.39 0.894
44.983 82.931 23.812 25.400 19.050 1.5 0.8 76 500 99 000 7 800 10 100 4 500 6 000 25584 25520 53 51 74 77 1.5 0.8 17.6 0.33 1.8 0.99 0.354 0.203
45.000 93.264 20.638 22.225 15.082 0.8 1.3 77 000 93 000 7 900 9 500 3 800 5 300 376 374 54 54 85 88 0.8 1.3 17.1 0.34 1.8 0.97 0.492 0.174
45.230 79.985 19.842 20.638 15.080 2.0 1.3 62 000 78 500 6 300 8 000 4 500 6 000 17887 17831 57 52 68 74 2 1.3 15.9 0.37 1.6 0.90 0.274 0.136
45.242 73.431 19.558 19.812 15.748 3.5 0.8 53 500 75 000 5 450 7 650 4 800 6 300 LM 102949 LM 102910 56 50 68 70 3.5 0.8 14.6 0.31 2.0 1.1 0.213 0.102
77.788 19.842 19.842 15.080 3.5 0.8 56 000 71 000 5 700 7 250 4 500 6 300 LM 603049 LM 603011 57 50 71 74 3.5 0.8 17.2 0.43 1.4 0.77 0.249 0.119
77.788 21.430 19.842 16.667 3.5 0.8 56 000 71 000 5 700 7 250 4 500 6 300 LM 603049 LM 603012 57 50 70 74 3.5 0.8 18.8 0.43 1.4 0.77 0.249 0.137
45.618 82.931 23.812 25.400 19.050 3.5 0.8 76 500 99 000 7 800 10 100 4 500 6 000 25590 25520 58 51 74 77 3.5 0.8 17.6 0.33 1.8 0.99 0.343 0.203
82.931 26.988 25.400 22.225 3.5 2.3 76 500 99 000 7 800 10 100 4 500 6 000 25590 25523 58 51 72 77 3.5 2.3 20.8 0.33 1.8 0.99 0.343 0.248
46.000 75.000 18.000 18.000 14.000 2.3 1.5 51 000 71 500 5 200 7 300 4 500 6 300 * LM 503349 ** LM 503310 55 51 67 71 2.3 1.5 15.9 0.40 1.5 0.82 0.209 0.096
46.038 79.375 17.462 17.462 13.495 2.8 1.5 46 000 57 000 4 700 5 800 4 500 6 000 18690 18620 56 51 71 74 2.8 1.5 15.5 0.37 1.6 0.88 0.211 0.126
80.962 19.050 17.462 14.288 0.8 1.5 45 000 57 000 4 600 5 800 4 300 6 000 13181 13318 52 52 72 76 0.8 1.5 20.1 0.53 1.1 0.63 0.236 0.144
85.000 20.638 21.692 17.462 2.3 1.3 71 500 81 500 7 300 8 300 4 300 6 000 359 S 354 A 55 51 77 80 2.3 1.3 15.4 0.31 2.0 1.1 0.343 0.162
85.000 25.400 25.608 20.638 3.5 1.3 79 500 105 000 8 100 10 700 4 300 6 000 2984 2924 58 52 76 80 3.5 1.3 19.0 0.35 1.7 0.95 0.397 0.223
95.250 27.783 29.901 22.225 3.5 0.8 106 000 126 000 10 800 12 900 4 300 5 600 436 432 A 59 52 84 87 3.5 0.8 18.6 0.28 2.1 1.2 0.536 0.381
47.625 88.900 20.638 22.225 16.513 3.5 1.3 73 000 85 000 7 450 8 650 4 000 5 600 369 A 362 A 60 53 81 84 3.5 1.3 16.6 0.32 1.9 1.0 0.381 0.166
88.900 25.400 25.400 19.050 3.5 3.3 86 000 107 000 8 750 10 900 4 000 5 600 M 804049 M 804010 63 56 77 85 3.5 3.3 23.8 0.55 1.1 0.60 0.455 0.218
95.250 30.162 29.370 23.020 3.5 3.3 106 000 143 000 10 800 14 500 3 800 5 300 HM 804846 HM 804810 66 57 81 91 3.5 3.3 26.1 0.55 1.1 0.60 0.626 0.354
101.600 34.925 36.068 26.988 3.5 3.3 137 000 169 000 14 000 17 200 3 800 5 000 528 522 62 55 89 95 3.5 3.3 22.1 0.29 2.1 1.2 0.894 0.416
111.125 30.162 26.909 20.638 3.5 3.3 92 500 110 000 9 450 11 200 3 200 4 300 55187 55437 69 62 92 105 3.5 3.3 37.3 0.88 0.68 0.37 0.817 0.514
112.712 30.162 26.909 20.638 3.5 3.3 92 500 110 000 9 450 11 200 3 200 4 300 55187 55443 69 62 92 106 3.5 3.3 37.3 0.88 0.68 0.37 0.816 0.554
117.475 33.338 31.750 23.812 3.5 3.3 137 000 156 000 13 900 15 900 3 200 4 300 66187 66462 66 62 100 111 3.5 3.3 32.1 0.63 0.96 0.53 1.19 0.552
123.825 36.512 32.791 25.400 3.5 3.3 143 000 160 000 14 600 16 400 3 000 4 000 72187 72487 72 66 102 116 3.5 3.3 37.0 0.74 0.81 0.45 1.29 0.79
B 148 B 149
B110-181E.indd 148-149 11/20/13 4:57:09 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
48.412 95.250 30.162 29.370 23.020 3.5 3.3 106 000 143 000 10 800 14 500 3 800 5 300 HM 804849 HM 804810 66 57 81 91 3.5 3.3 26.1 0.55 1.1 0.60 0.61 0.354
95.250 30.162 29.370 23.020 2.3 3.3 106 000 143 000 10 800 14 500 3 800 5 300 HM 804848 HM 804810 63 57 81 91 2.3 3.3 26.1 0.55 1.1 0.60 0.614 0.354
49.212 104.775 36.512 36.512 28.575 3.5 0.8 139 000 192 000 14 200 19 600 3 400 4 800 HM 807044 HM 807011 69 63 91 100 3.5 0.8 29.7 0.49 1.2 0.68 1.03 0.508
114.300 44.450 44.450 36.068 3.5 3.3 196 000 243 000 20 000 24 800 3 400 4 800 HH 506348 HH 506310 71 61 97 107 3.5 3.3 30.8 0.40 1.5 0.82 1.43 0.837
50.000 82.000 21.500 21.500 17.000 3.0 0.5 71 000 96 000 7 250 9 800 4 300 5 600 JLM 104948 JLM 104910 60 55 76 78 3 0.5 16.1 0.31 2.0 1.1 0.306 0.129
82.550 21.590 22.225 16.510 0.5 1.3 71 000 96 000 7 250 9 800 4 300 5 600 * LM 104947 A LM 104911 55 55 75 78 0.5 1.3 15.7 0.31 2.0 1.1 0.316 0.133
88.900 20.638 22.225 16.513 2.3 1.3 73 000 85 000 7 450 8 650 4 000 5 600 366 362 A 59 55 81 84 2.3 1.3 16.6 0.32 1.9 1.0 0.351 0.166
90.000 28.000 28.000 23.000 3.0 2.5 104 000 136 000 10 600 13 900 4 000 5 600 JM 205149 JM 205110 62 57 80 85 3 2.5 19.9 0.33 1.8 1.0 0.507 0.246
105.000 37.000 36.000 29.000 3.0 2.5 139 000 192 000 14 200 19 600 3 400 4 800 JHM 807045 JHM 807012 69 63 90 100 3 2.5 29.7 0.49 1.2 0.68 1.01 0.523
50.800 80.962 18.258 18.258 14.288 1.5 1.5 53 000 81 000 5 400 8 250 4 300 5 600 L 305649 L 305610 58 56 73 77 1.5 1.5 15.7 0.36 1.7 0.93 0.239 0.119
82.550 23.622 22.225 18.542 3.5 0.8 71 000 96 000 7 250 9 800 4 300 5 600 LM 104949 LM 104911 A 62 55 75 78 3.5 0.8 17.8 0.31 2.0 1.1 0.303 0.156
82.931 21.590 22.225 16.510 3.5 1.3 71 000 96 000 7 250 9 800 4 300 5 600 LM 104949 LM 104912 62 55 75 78 3.5 1.3 15.7 0.31 2.0 1.1 0.301 0.14
85.000 17.462 17.462 13.495 3.5 1.5 48 500 63 000 4 950 6 450 4 300 5 600 18790 18720 62 56 77 80 3.5 1.5 16.7 0.41 1.5 0.81 0.239 0.136
85.725 19.050 18.263 12.700 1.5 1.5 42 500 54 000 4 350 5 500 4 000 5 300 18200 18337 59 56 76 81 1.5 1.5 21.0 0.57 1.1 0.58 0.268 0.136
88.900 20.638 22.225 16.513 3.5 1.3 73 000 85 000 7 450 8 650 4 000 5 600 368 A 362 A 62 56 81 84 3.5 1.3 16.6 0.32 1.9 1.0 0.338 0.166
88.900 20.638 22.225 16.513 1.5 1.3 73 000 85 000 7 450 8 650 4 000 5 600 368 362 A 58 56 81 84 1.5 1.3 16.6 0.32 1.9 1.0 0.341 0.166
92.075 24.608 25.400 19.845 3.5 0.8 84 500 117 000 8 600 11 900 4 000 5 300 28580 28521 63 57 83 87 3.5 0.8 20.0 0.38 1.6 0.87 0.46 0.247
93.264 30.162 30.302 23.812 0.8 0.8 103 000 136 000 10 500 13 900 3 800 5 300 3775 3730 58 58 84 88 0.8 0.8 22.4 0.34 1.8 0.97 0.568 0.297
93.264 30.162 30.302 23.812 3.5 0.8 103 000 136 000 10 500 13 900 3 800 5 300 3780 3730 64 58 84 88 3.5 0.8 22.4 0.34 1.8 0.97 0.564 0.297
95.250 27.783 28.575 22.225 3.5 2.3 110 000 144 000 11 200 14 700 3 800 5 300 33889 33821 64 58 85 90 3.5 2.3 19.8 0.33 1.8 1.0 0.601 0.267
101.600 31.750 31.750 25.400 3.5 3.3 118 000 150 000 12 100 15 200 3 600 5 000 49585 49520 66 59 88 96 3.5 3.3 23.4 0.40 1.5 0.82 0.744 0.389
101.600 34.925 36.068 26.988 0.8 3.3 137 000 169 000 14 000 17 200 3 800 5 000 529 522 59 58 89 95 0.8 3.3 22.1 0.29 2.1 1.2 0.822 0.416
101.600 34.925 36.068 26.988 3.5 3.3 137 000 169 000 14 000 17 200 3 800 5 000 529 X 522 65 58 89 95 3.5 3.3 22.1 0.29 2.1 1.2 0.819 0.416
104.775 36.512 36.512 28.575 3.5 0.8 139 000 192 000 14 200 19 600 3 400 4 800 HM 807046 HM 807011 70 63 91 100 3.5 0.8 29.7 0.49 1.2 0.68 0.992 0.508
104.775 36.512 36.512 28.575 3.5 3.3 139 000 192 000 14 200 19 600 3 400 4 800 HM 807046 HM 807010 70 63 89 100 3.5 3.3 29.7 0.49 1.2 0.68 0.993 0.502
108.966 34.925 36.512 26.988 3.5 3.3 145 000 181 000 14 700 18 500 3 600 4 800 59200 59429 68 61 93 101 3.5 3.3 25.4 0.40 1.5 0.82 0.943 0.594
111.125 30.162 26.909 20.638 3.5 3.3 113 000 152 000 11 500 15 400 3 000 4 300 55200 C 55437 71 65 92 105 3.5 3.3 37.6 0.88 0.68 0.37 0.845 0.514
111.125 30.162 26.909 20.638 3.5 3.3 92 500 110 000 9 450 11 200 3 200 4 300 55200 55437 71 64 92 105 3.5 3.3 37.3 0.88 0.68 0.37 0.767 0.514
123.825 36.512 32.791 25.400 3.5 3.3 162 000 199 000 16 500 20 300 2 800 4 000 72200 C 72487 77 67 102 116 3.5 3.3 38.0 0.74 0.81 0.45 1.33 0.79
123.825 36.512 32.791 25.400 3.5 3.3 143 000 160 000 14 600 16 400 3 000 4 000 72200 72487 74 66 102 116 3.5 3.3 37.0 0.74 0.81 0.45 1.22 0.79
127.000 44.450 44.450 34.925 3.5 3.3 199 000 258 000 20 200 26 300 3 000 4 000 65200 65500 75 69 107 119 3.5 3.3 35.0 0.49 1.2 0.68 1.86 1.03
127.000 50.800 52.388 41.275 3.5 3.3 236 000 300 000 24 000 31 000 3 200 4 300 6279 6220 71 65 108 117 3.5 3.3 30.7 0.30 2.0 1.1 2.08 1.22
52.388 92.075 24.608 25.400 19.845 3.5 0.8 84 500 117 000 8 600 11 900 4 000 5 300 28584 28521 65 58 83 87 3.5 0.8 20.0 0.38 1.6 0.87 0.435 0.247
100.000 25.000 22.225 21.824 2.3 2.0 77 000 93 000 7 900 9 500 3 800 5 300 377 372 62 58 86 90 2.3 2 21.4 0.34 1.8 0.97 0.392 0.435
111.125 30.162 26.909 20.638 3.5 3.3 92 500 110 000 9 450 11 200 3 200 4 300 55206 55437 72 64 92 105 3.5 3.3 37.3 0.88 0.68 0.37 0.737 0.514
B 150 B 151
B110-181E.indd 150-151 11/20/13 4:57:10 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
53.975 104.775 39.688 40.157 33.338 3.5 3.3 148 000 207 000 15 100 21 100 3 600 4 800 4595 4535 70 63 90 99 3.5 3.3 27.4 0.34 1.79 0.98 0.989 0.589
107.950 36.512 36.957 28.575 3.5 3.3 144 000 182 000 14 700 18 500 3 600 4 800 539 532 X 68 61 94 100 3.5 3.3 24.3 0.30 2.0 1.1 0.88 0.57
122.238 33.338 31.750 23.812 3.5 3.3 135 000 156 000 13 800 15 900 3 000 4 000 66584 66520 75 68 105 116 3.5 3.3 34.3 0.67 0.90 0.50 1.2 0.558
123.825 36.512 32.791 25.400 3.5 3.3 143 000 160 000 14 600 16 400 3 000 4 000 72212 72487 77 66 102 116 3.5 3.3 37.0 0.74 0.81 0.45 1.16 0.79
123.825 36.512 32.791 25.400 3.5 3.3 162 000 199 000 16 500 20 300 2 800 4 000 72212 C 72487 79 67 102 116 3.5 3.3 38.0 0.74 0.81 0.45 1.27 0.79
123.825 38.100 36.678 30.162 3.5 3.3 161 000 221 000 16 400 22 500 3 000 4 000 557 S 552 A 71 65 109 116 3.5 3.3 28.8 0.35 1.7 0.95 1.49 0.764
127.000 44.450 44.450 34.925 3.5 3.3 199 000 258 000 20 200 26 300 3 000 4 000 65212 65500 77 71 107 119 3.5 3.3 35.0 0.49 1.2 0.68 1.76 1.03
127.000 50.800 52.388 41.275 3.5 3.3 236 000 300 000 24 000 31 000 3 200 4 300 6280 6220 74 67 108 117 3.5 3.3 30.7 0.30 2.0 1.1 1.97 1.22
130.175 36.512 33.338 23.812 3.5 3.3 133 000 154 000 13 600 15 700 2 600 3 600 HM911242 HM911210 79 74 109 124 3.5 3.3 42.2 0.82 0.73 0.40 1.45 0.725
55.000 90.000 23.000 23.000 18.500 1.5 0.5 79 000 111 000 8 050 11 300 3 800 5 300 JLM506849 JLM506810 63 61 82 86 1.5 0.5 19.7 0.40 1.5 0.82 0.378 0.186
95.000 29.000 29.000 23.500 1.5 2.5 111 000 152 000 11 300 15 500 3 800 5 000 JM207049 JM207010 64 62 85 91 1.5 2.5 21.3 0.33 1.8 0.99 0.59 0.26
96.838 21.000 21.946 15.875 2.3 0.8 80 500 100 000 8 200 10 200 3 600 5 000 385 382 A 65 61 89 92 2.3 0.8 17.6 0.35 1.7 0.93 0.455 0.179
110.000 39.000 39.000 32.000 3.0 2.5 177 000 225 000 18 000 23 000 3 400 4 500 JH307749 JH307710 71 64 97 104 3 2.5 27.2 0.35 1.7 0.95 1.13 0.567
115.000 41.021 41.275 31.496 3.0 3.0 172 000 214 000 17 500 21 800 3 200 4 500 622 X 614 X 70 64 101 108 3 3 26.6 0.31 1.9 1.1 1.3 0.597
55.562 97.630 24.608 24.608 19.446 3.5 0.8 89 000 129 000 9 100 13 100 3 600 5 000 28680 28622 68 62 88 92 3.5 0.8 21.3 0.40 1.5 0.82 0.499 0.27
122.238 43.658 43.764 36.512 1.3 3.3 198 000 292 000 20 200 29 700 3 000 4 000 5566 5535 70 68 106 116 1.3 3.3 29.9 0.36 1.7 0.92 1.76 0.815
123.825 36.512 32.791 25.400 3.5 3.3 143 000 160 000 14 600 16 400 3 000 4 000 72218 72487 78 66 102 116 3.5 3.3 37.0 0.74 0.81 0.45 1.12 0.79
123.825 36.512 32.791 25.400 3.5 3.3 162 000 199 000 16 500 20 300 2 800 4 000 72218 C 72487 80 67 102 116 3.5 3.3 38.0 0.74 0.81 0.45 1.23 0.79
57.150 96.838 21.000 21.946 15.875 3.5 0.8 80 500 100 000 8 200 10 200 3 600 5 000 387 A 382 A 69 62 89 92 3.5 0.8 17.6 0.35 1.7 0.93 0.42 0.179
96.838 21.000 21.946 15.875 2.3 0.8 80 500 100 000 8 200 10 200 3 600 5 000 387 382 A 66 62 89 92 2.3 0.8 17.6 0.35 1.7 0.93 0.423 0.179
96.838 25.400 21.946 20.275 3.5 2.3 80 500 100 000 8 200 10 200 3 600 5 000 387 A 382 S 69 62 87 91 3.5 2.3 22.0 0.35 1.7 0.93 0.42 0.249
98.425 21.000 21.946 17.826 3.5 0.8 80 500 100 000 8 200 10 200 3 600 5 000 387 A 382 69 62 90 92 3.5 0.8 17.6 0.35 1.7 0.93 0.42 0.226
104.775 30.162 29.317 24.605 3.5 3.3 116 000 149 000 11 800 15 200 3 400 4 800 469 453 X 70 63 92 98 3.5 3.3 23.1 0.34 1.8 0.98 0.692 0.376
104.775 30.162 29.317 24.605 2.3 3.3 116 000 149 000 11 800 15 200 3 400 4 800 462 453 X 67 63 92 98 2.3 3.3 23.1 0.34 1.8 0.98 0.694 0.376
104.775 30.162 30.958 23.812 0.8 3.3 130 000 170 000 13 300 17 400 3 400 4 800 45289 45220 65 65 93 99 0.8 3.3 21.9 0.33 1.8 0.99 0.752 0.347
104.775 30.162 30.958 23.812 0.8 0.8 130 000 170 000 13 300 17 400 3 400 4 800 45289 45221 65 65 95 99 0.8 0.8 21.9 0.33 1.8 0.99 0.76 0.35
122.238 33.338 31.750 23.812 3.5 3.3 135 000 156 000 13 800 15 900 3 000 4 000 66587 66520 77 71 105 116 3.5 3.3 34.3 0.67 0.90 0.50 1.14 0.558
123.825 36.512 32.791 25.400 3.5 3.3 162 000 199 000 16 500 20 300 2 800 4 000 72225 C 72487 81 67 102 116 3.5 3.3 38.0 0.74 0.81 0.45 1.19 0.79
123.825 38.100 36.678 30.162 3.5 3.3 161 000 221 000 16 400 22 500 3 000 4 000 555 S 552 A 83 68 109 116 3.5 3.3 28.8 0.35 1.7 0.95 1.41 0.764
140.030 36.512 33.236 23.520 3.5 2.3 152 000 183 000 15 500 18 700 2 600 3 600 78225 78551 83 77 117 132 3.5 2.3 44.2 0.87 0.69 0.38 1.67 0.926
144.983 36.000 33.236 23.007 3.5 3.5 152 000 183 000 15 500 18 700 2 600 3 600 78225 78571 83 77 118 132 3.5 3.5 43.6 0.87 0.69 0.38 1.68 1.08
149.225 53.975 54.229 44.450 3.5 3.3 287 000 410 000 29 300 41 500 2 600 3 400 6455 6420 81 75 129 140 3.5 3.3 39.0 0.36 1.7 0.91 3.49 1.63
57.531 96.838 21.000 21.946 15.875 3.5 0.8 80 500 100 000 8 200 10 200 3 600 5 000 388 A 382 A 69 63 89 92 3.5 0.8 17.6 0.35 1.7 0.93 0.416 0.179
58.738 112.712 33.338 30.048 26.988 3.5 3.3 120 000 173 000 12 200 17 700 3 200 4 300 3981 3926 73 67 98 106 3.5 3.3 28.7 0.40 1.5 0.82 0.899 0.541
Note The tolerances are listed in Tables 2, 3 and 4 on Pages B113 and B114.
B 152 B 153
B110-181E.indd 152-153 11/20/13 4:57:11 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
60.000 95.000 24.000 24.000 19.000 5.0 2.5 86 500 125 000 8 800 12 800 3 600 5 000 JLM 508748 JLM 508710 75 66 85 91 5 2.5 21.6 0.40 1.5 0.82 0.43 0.20
104.775 21.433 22.000 15.875 2.3 2.0 83 500 107 000 8 500 10 900 3 400 4 500 * 39236 39412 71 67 96 100 2.3 2 20.0 0.39 1.5 0.85 0.559 0.186
110.000 22.000 21.996 18.824 0.8 1.3 85 500 113 000 8 750 11 500 3 200 4 300 397 394 A 69 68 101 104 0.8 1.3 20.9 0.40 1.5 0.82 0.642 0.263
122.238 33.338 31.750 23.812 3.5 3.3 135 000 156 000 13 800 15 900 3 000 4 000 66585 66520 79 73 105 116 3.5 3.3 34.3 0.67 0.90 0.50 1.07 0.558
60.325 100.000 25.400 25.400 19.845 3.5 3.3 91 000 135 000 9 250 13 700 3 400 4 800 28985 28921 73 67 89 96 3.5 3.3 22.9 0.43 1.4 0.78 0.538 0.232
101.600 25.400 25.400 19.845 3.5 3.3 91 000 135 000 9 250 13 700 3 400 4 800 28985 28920 73 67 90 97 3.5 3.3 22.9 0.43 1.4 0.78 0.538 0.272
122.238 38.100 36.678 30.162 2.3 3.3 161 000 221 000 16 400 22 500 3 000 4 000 558 553 X 73 69 108 115 2.3 3.3 28.8 0.35 1.7 0.95 1.33 0.692
122.238 38.100 38.354 29.718 8.0 1.5 188 000 245 000 19 200 25 000 3 000 4 000 HM 212044 HM 212010 85 70 110 116 8 1.5 27.0 0.34 1.8 0.98 1.43 0.604
122.238 43.658 43.764 36.512 0.8 3.3 198 000 292 000 20 200 29 700 3 000 4 000 5582 5535 73 72 106 116 0.8 3.3 29.9 0.36 1.7 0.92 1.61 0.815
127.000 44.450 44.450 34.925 3.5 3.3 199 000 258 000 20 200 26 300 3 000 4 000 65237 65500 82 71 107 119 3.5 3.3 35.0 0.49 1.2 0.68 1.56 1.03
130.175 41.275 41.275 31.750 3.5 3.3 195 000 263 000 19 800 26 800 2 800 3 800 637 633 78 72 116 124 3.5 3.3 29.9 0.36 1.7 0.91 1.87 0.712
135.755 53.975 56.007 44.450 3.5 3.3 264 000 355 000 27 000 36 000 2 800 3 800 6376 6320 81 74 117 126 3.5 3.3 35.0 0.32 1.8 1.0 2.45 1.39
61.912 136.525 46.038 46.038 36.512 3.5 3.3 233 000 370 000 23 800 37 500 2 600 3 400 H 715334 H 715311 84 78 119 132 3.5 3.3 37.1 0.47 1.3 0.70 2.51 0.961
146.050 41.275 39.688 25.400 3.5 3.3 193 000 225 000 19 700 22 900 2 400 3 400 H 913842 H 913810 90 82 124 138 3.5 3.3 44.4 0.78 0.77 0.42 2.2 0.898
152.400 47.625 46.038 31.750 3.5 3.3 237 000 267 000 24 200 27 300 2 400 3 400 9180 9121 90 81 130 145 3.5 3.3 44.3 0.66 0.92 0.50 2.77 1.21
63.500 94.458 19.050 19.050 15.083 1.5 1.5 59 000 100 000 6 050 10 200 3 600 4 800 L 610549 L 610510 71 69 86 91 1.5 1.5 19.6 0.42 1.4 0.78 0.306 0.154
104.775 21.433 22.000 15.875 2.0 2.0 83 500 107 000 8 500 10 900 3 400 4 500 39250 39412 73 69 96 100 2 2 20.0 0.39 1.5 0.85 0.501 0.186
107.950 25.400 25.400 19.050 1.5 3.3 90 000 138 000 9 150 14 100 3 200 4 300 29586 29520 73 71 96 103 1.5 3.3 24.0 0.46 1.3 0.72 0.661 0.281
110.000 22.000 21.996 18.824 3.5 1.3 85 500 113 000 8 750 11 500 3 200 4 300 395 394 A 77 70 101 104 3.5 1.3 20.9 0.40 1.5 0.82 0.58 0.263
110.000 22.000 21.996 18.824 1.5 1.3 85 500 113 000 8 750 11 500 3 200 4 300 390 A 394 A 73 70 101 104 1.5 1.3 20.9 0.40 1.5 0.82 0.583 0.263
112.712 30.162 30.048 23.812 3.5 3.2 120 000 173 000 12 200 17 700 3 200 4 300 3982 3920 77 71 99 106 3.5 3.2 25.5 0.40 1.5 0.82 0.789 0.454
112.712 30.162 30.162 23.812 3.5 3.3 142 000 202 000 14 500 20 600 3 200 4 300 39585 39520 77 71 101 107 3.5 3.3 23.5 0.34 1.8 0.97 0.899 0.359
112.712 33.338 30.048 26.988 3.5 3.3 120 000 173 000 12 200 17 700 3 200 4 300 3982 3926 78 71 98 106 3.5 3.3 28.7 0.40 1.5 0.82 0.789 0.541
122.238 38.100 38.354 29.718 7.0 3.3 188 000 245 000 19 200 25 000 3 000 4 000 HM 212047 HM 212011 87 73 108 116 7 3.3 26.9 0.34 1.8 0.98 1.34 0.598
122.238 38.100 38.354 29.718 7.0 1.5 188 000 245 000 19 200 25 000 3 000 4 000 HM 212047 HM 212010 87 73 110 116 7 1.5 26.9 0.34 1.8 0.98 1.34 0.604
122.238 38.100 38.354 29.718 3.5 1.5 188 000 245 000 19 200 25 000 3 000 4 000 HM 212046 HM 212010 80 73 110 116 3.5 1.5 26.9 0.34 1.8 0.98 1.35 0.604
122.238 43.658 43.764 36.512 3.5 3.3 198 000 292 000 20 200 29 700 3 000 4 000 5584 5535 81 75 106 116 3.5 3.3 29.9 0.36 1.7 0.92 1.5 0.815
123.825 38.100 36.678 30.162 3.5 3.3 161 000 221 000 16 400 22 500 3 000 4 000 559 522 A 78 73 109 116 3.5 3.3 28.8 0.35 1.7 0.95 1.23 0.764
127.000 36.512 36.170 28.575 3.5 3.3 166 000 234 000 16 900 23 900 2 800 3 800 565 563 80 73 112 120 3.5 3.3 28.3 0.36 1.6 0.91 1.46 0.655
130.175 41.275 41.275 31.750 3.5 3.3 195 000 263 000 19 800 26 800 2 800 3 800 639 633 81 74 116 124 3.5 3.3 29.9 0.36 1.7 0.91 1.77 0.712
136.525 36.512 33.236 23.520 2.3 3.3 152 000 183 000 15 500 18 700 2 600 3 600 78250 78537 85 79 115 130 2.3 3.3 44.2 0.87 0.69 0.38 1.51 0.782
136.525 41.275 41.275 31.750 3.5 3.3 195 000 263 000 19 800 26 800 2 800 3 800 639 632 79 76 119 125 3.5 3.3 29.9 0.36 1.7 0.91 1.77 1.04
140.030 36.512 33.236 23.520 2.3 2.3 152 000 183 000 15 500 18 700 2 600 3 600 78250 78551 85 79 117 132 2.3 2.3 44.2 0.87 0.69 0.38 1.51 0.926
64.963 127.000 36.512 36.170 28.575 3.5 3.3 166 000 234 000 16 900 23 900 2 800 3 800 569 563 81 74 112 120 3.5 3.3 28.3 0.36 1.6 0.91 1.41 0.655
B 154 B 155
B110-181E.indd 154-155 11/20/13 4:57:12 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
65.000 105.000 24.000 23.000 18.500 3.0 1.0 93 000 126 000 9 500 12 900 3 400 4 500 JLM 710949 JLM 710910 77 71 96 101 3 1 23.7 0.45 1.3 0.73 0.526 0.237
110.000 28.000 28.000 22.500 3.0 2.5 120 000 173 000 12 200 17 700 3 200 4 300 JM 511946 JM 511910 78 72 99 105 3 2.5 24.5 0.40 1.5 0.82 0.72 0.342
120.000 29.002 29.007 23.444 2.3 3.3 123 000 169 000 12 500 17 200 3 000 4 000 478 472 A 77 73 106 114 2.3 3.3 24.3 0.38 1.6 0.86 0.942 0.466
120.000 39.000 38.500 32.000 3.0 2.5 185 000 249 000 18 800 25 400 3 000 4 000 JH 211749 JH 211710 80 74 107 114 3 2.5 27.9 0.34 1.8 0.98 1.25 0.625
65.088 135.755 53.975 56.007 44.450 3.5 3.3 264 000 355 000 27 000 36 000 2 800 3 800 6379 6320 84 77 117 126 3.5 3.3 35.0 0.32 1.8 1.0 2.25 1.39
136.525 46.038 46.038 36.512 3.5 3.3 233 000 370 000 23 800 37 500 2 600 3 400 H 715340 H 715311 88 82 118 132 3.5 3.3 37.1 0.47 1.3 0.70 2.4 0.961
66.675 110.000 22.000 21.996 18.824 0.8 1.3 85 500 113 000 8 750 11 500 3 200 4 300 395 A 394 A 73 73 101 104 0.8 1.3 20.9 0.40 1.5 0.82 0.528 0.263
110.000 22.000 21.996 18.824 3.5 1.3 85 500 113 000 8 750 11 500 3 200 4 300 395 S 394 A 79 73 101 104 3.5 1.3 20.9 0.40 1.5 0.82 0.524 0.263
112.712 30.162 30.048 23.812 3.5 3.2 120 000 173 000 12 200 17 700 3 200 4 300 3984 3920 80 74 99 106 3.5 3.2 25.5 0.40 1.5 0.82 0.712 0.454
112.712 30.162 30.048 23.812 5.5 3.2 120 000 173 000 12 200 17 700 3 200 4 300 3994 3920 84 74 99 106 5.5 3.2 25.5 0.40 1.5 0.82 0.706 0.454
112.712 30.162 30.162 23.812 3.5 0.8 142 000 202 000 14 500 20 600 3 200 4 300 39590 39521 80 74 103 107 3.5 0.8 23.5 0.34 1.8 0.97 0.822 0.365
112.712 30.162 30.162 23.812 3.5 3.3 142 000 202 000 14 500 20 600 3 200 4 300 39590 39520 80 74 101 107 3.5 3.3 23.5 0.34 1.8 0.97 0.822 0.359
117.475 30.162 30.162 23.812 3.5 3.3 119 000 179 000 12 200 18 300 3 000 4 000 33262 33462 81 75 104 112 3.5 3.3 26.8 0.44 1.4 0.76 0.911 0.442
122.238 38.100 36.678 30.162 3.5 3.3 161 000 221 000 16 400 22 500 3 000 4 000 560 553 X 81 75 108 115 3.5 3.3 28.8 0.35 1.7 0.95 1.14 0.692
122.238 38.100 38.354 29.718 3.5 1.5 188 000 245 000 19 200 25 000 3 000 4 000 HM 212049 HM 212010 82 75 110 116 3.5 1.5 26.9 0.34 1.8 0.98 1.25 0.604
122.238 38.100 38.354 29.718 3.5 3.3 188 000 245 000 19 200 25 000 3 000 4 000 HM 212049 HM 212011 81 74 108 116 3.5 3.3 26.9 0.34 1.8 0.98 1.25 0.598
123.825 38.100 36.678 30.162 3.5 3.3 161 000 221 000 16 400 22 500 3 000 4 000 560 552 A 81 75 109 116 3.5 3.3 28.8 0.35 1.7 0.95 1.14 0.764
136.525 46.038 46.038 36.512 3.5 3.3 233 000 370 000 23 800 37 500 2 600 3 400 H 715341 H 715311 89 83 118 132 3.5 3.3 37.1 0.47 1.3 0.70 2.34 0.961
68.262 110.000 22.000 21.996 18.824 2.3 1.3 85 500 113 000 8 750 11 500 3 200 4 300 399 A 394 A 78 74 101 104 2.3 1.3 20.9 0.40 1.5 0.82 0.497 0.263
120.000 29.795 29.007 24.237 3.5 2.0 123 000 169 000 12 500 17 200 3 000 4 000 480 472 83 76 106 113 3.5 2 25.1 0.38 1.6 0.86 0.862 0.493
122.238 38.100 36.678 30.162 3.5 3.3 161 000 221 000 16 400 22 500 3 000 4 000 560 S 553 X 83 76 108 115 3.5 3.3 28.8 0.35 1.7 0.95 1.09 0.692
127.000 36.512 36.170 28.575 3.5 3.3 166 000 234 000 16 900 23 900 2 800 3 800 570 563 83 77 112 120 3.5 3.3 28.3 0.36 1.6 0.91 1.32 0.655
136.525 41.275 41.275 31.750 3.5 3.3 229 000 297 000 23 300 30 500 2 600 3 600 H 414245 H 414210 86 82 121 129 3.5 3.3 30.6 0.36 1.7 0.92 1.95 0.796
136.525 46.038 46.038 36.512 3.5 3.3 233 000 370 000 23 800 37 500 2 600 3 400 H 715343 H 715311 90 84 118 132 3.5 3.3 37.1 0.47 1.3 0.70 2.28 0.961
152.400 47.625 46.038 31.750 3.5 3.3 237 000 267 000 24 200 27 300 2 400 3 400 9185 9121 94 81 130 145 3.5 3.3 44.3 0.66 0.92 0.50 2.53 1.21
69.850 112.712 22.225 21.996 15.875 1.5 0.8 85 000 113 000 8 650 11 500 3 000 4 000 LM 613449 LM 613410 78 76 104 107 1.5 0.8 22.1 0.42 1.4 0.79 0.562 0.238
112.712 25.400 25.400 19.050 1.5 3.3 96 000 152 000 9 800 15 500 2 800 4 000 29675 29620 80 77 101 109 1.5 3.3 26.3 0.49 1.2 0.68 0.695 0.273
117.475 30.162 30.162 23.812 3.5 3.3 119 000 179 000 12 200 18 300 3 000 4 000 33275 33462 84 77 104 112 3.5 3.3 26.8 0.44 1.4 0.76 0.83 0.442
120.000 32.545 32.545 26.195 3.5 3.3 152 000 225 000 15 500 22 900 3 000 4 000 47487 47420 84 78 107 114 3.5 3.3 26.0 0.36 1.7 0.92 1.02 0.477
120.650 25.400 25.400 19.050 1.5 3.3 96 000 152 000 9 800 15 500 2 800 4 000 29675 29630 79 78 105 113 1.5 3.3 26.3 0.49 1.2 0.68 0.695 0.489
127.000 36.512 36.170 28.575 3.5 0.8 166 000 234 000 16 900 23 900 2 800 3 800 566 563 X 85 78 114 120 3.5 0.8 28.3 0.36 1.6 0.91 1.27 0.658
130.175 41.275 41.275 31.750 3.5 3.3 195 000 263 000 19 800 26 800 2 800 3 800 643 633 86 80 116 124 3.5 3.3 29.9 0.36 1.7 0.91 1.56 0.712
146.050 41.275 39.688 25.400 3.5 3.3 193 000 225 000 19 700 22 900 2 400 3 400 H 913849 H 913810 95 82 124 138 3.5 3.3 44.4 0.78 0.77 0.42 1.95 0.898
146.050 41.275 41.275 31.750 3.5 3.3 207 000 296 000 21 100 30 000 2 400 3 200 655 653 88 82 131 139 3.5 3.3 33.2 0.41 1.5 0.81 2.35 0.891
149.225 53.975 54.229 44.450 5.0 3.3 287 000 410 000 29 300 41 500 2 600 3 400 6454 6420 94 85 129 140 5 3.3 39.0 0.36 1.7 0.91 2.95 1.63
150.089 44.450 46.672 36.512 3.5 3.3 265 000 370 000 27 000 37 500 2 400 3 200 745 A 742 88 82 134 142 3.5 3.3 32.5 0.33 1.8 1.0 2.82 1.07
B 156 B 157
B110-181E.indd 156-157 11/20/13 4:57:13 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
70.000 110.000 26.000 25.000 20.500 1.0 2.5 98 500 152 000 10 000 15 500 3 000 4 000 JLM 813049 JLM 813010 78 77 98 105 1 2.5 26.2 0.49 1.2 0.68 0.604 0.304
115.000 29.000 29.000 23.000 3.0 2.5 126 000 177 000 12 900 18 100 3 000 4 000
JM 612949
JM 612910 83 77 103 110 3 2.5 26.4 0.43 1.4 0.77 0.800 0.362
120.000 29.795 29.007 24.237 2.0 2.0 123 000 169 000 12 500 17 200 3 000 4 000 484 472 80 78 106 113 2 2 25.1 0.38 1.6 0.86 0.822 0.493
71.438 117.475 30.162 30.162 23.812 3.5 3.3 119 000 179 000 12 200 18 300 3 000 4 000 33281 33462 85 79 104 112 3.5 3.3 26.8 0.44 1.4 0.76 0.789 0.442
120.000 32.545 32.545 26.195 3.5 3.3 152 000 225 000 15 500 22 900 3 000 4 000 47490 47420 86 79 107 114 3.5 3.3 26.0 0.36 1.7 0.92 0.983 0.477
127.000 36.512 36.170 28.575 6.4 3.3 166 000 234 000 16 900 23 900 2 800 3 800 567 S 563 92 80 112 120 6.4 3.3 28.3 0.36 1.6 0.91 1.21 0.655
127.000 36.512 36.170 28.575 3.5 3.3 166 000 234 000 16 900 23 900 2 800 3 800 567 A 563 86 80 112 120 3.5 3.3 28.3 0.36 1.6 0.91 1.23 0.655
130.175 41.275 41.275 31.750 6.4 3.3 195 000 263 000 19 800 26 800 2 800 3 800 645 633 93 81 116 124 6.4 3.3 29.9 0.36 1.7 0.91 1.49 0.712
136.525 41.275 41.275 31.750 3.5 3.3 195 000 263 000 19 800 26 800 2 800 3 800 644 632 87 81 118 125 3.5 3.3 29.9 0.36 1.7 0.91 1.5 1.04
136.525 41.275 41.275 31.750 3.5 3.3 229 000 297 000 23 300 30 500 2 600 3 600 H 414249 H 414210 89 83 121 129 3.5 3.3 30.6 0.36 1.7 0.92 1.83 0.796
136.525 46.038 46.038 36.512 3.5 3.3 233 000 370 000 23 800 37 500 2 600 3 400 H 715345 H 715311 92 84 119 132 3.5 3.3 37.1 0.47 1.3 0.70 2.15 0.961
73.025 112.712 25.400 25.400 19.050 3.5 3.3 96 000 152 000 9 800 15 500 2 800 4 000 29685 29620 86 80 101 109 3.5 3.3 26.3 0.49 1.2 0.68 0.62 0.273
117.475 30.162 30.162 23.812 3.5 3.3 119 000 179 000 12 200 18 300 3 000 4 000 33287 33462 87 80 104 112 3.5 3.3 26.8 0.44 1.4 0.76 0.746 0.442
127.000 36.512 36.170 28.575 3.5 3.3 166 000 234 000 16 900 23 900 2 800 3 800 567 563 88 81 112 120 3.5 3.3 28.3 0.36 1.6 0.91 1.17 0.655
146.050 41.275 41.275 31.750 3.5 3.3 207 000 296 000 21 100 30 000 2 400 3 200 657 653 91 85 131 139 3.5 3.3 33.2 0.41 1.5 0.81 2.24 0.891
149.225 53.975 54.229 44.450 3.5 3.3 287 000 410 000 29 300 41 500 2 600 3 400 6460 6420 93 87 129 140 3.5 3.3 39.0 0.36 1.7 0.91 2.8 1.63
73.817 127.000 36.512 36.170 28.575 0.8 3.3 166 000 234 000 16 900 23 900 2 800 3 800 568 563 83 82 112 120 0.8 3.3 28.3 0.36 1.6 0.91 1.15 0.655
74.612 150.000 41.275 41.275 31.750 3.5 3.0 207 000 296 000 21 100 30 000 2 400 3 200 658 653 X 92 86 133 141 3.5 3 33.2 0.41 1.5 0.81 2.37 0.932
75.000 115.000 25.000 25.000 19.000 3.0 2.5 101 000 150 000 10 300 15 300 3 000 4 000 JLM 714149 JLM 714110 87 81 104 110 3 2.5 25.3 0.46 1.3 0.72 0.638 0.272
120.000 31.000 29.500 25.000 3.0 2.5 129 000 198 000 13 100 20 200 2 800 3 800 JM 714249 JM 714210 88 83 108 115 3 2.5 28.8 0.44 1.4 0.74 0.863 0.436
145.000 51.000 51.000 42.000 3.0 2.5 283 000 410 000 28 900 41 500 2 600 3 400 JH 415647 JH 415610 94 89 129 139 3 2.5 36.7 0.36 1.7 0.91 2.64 1.19
76.200 121.442 24.608 23.012 17.462 2.0 2.0 89 000 124 000 9 100 12 600 2 800 3 800 34300 34478 86 84 111 116 2 2 26.3 0.45 1.3 0.73 0.65 0.316
127.000 30.162 31.000 22.225 3.5 3.3 134 000 195 000 13 700 19 900 2 800 3 800 42687 42620 90 84 114 121 3.5 3.3 27.3 0.42 1.4 0.79 1.03 0.438
127.000 30.162 31.001 22.225 6.4 3.3 134 000 195 000 13 700 19 900 2 800 3 800 42688 42620 94 84 114 121 6.4 3.3 27.3 0.42 1.4 0.79 1.01 0.438
133.350 33.338 33.338 26.195 0.8 3.3 154 000 237 000 15 700 24 200 2 600 3 600 47680 47620 86 85 119 128 0.8 3.3 29.0 0.40 1.5 0.82 1.39 0.577
135.733 44.450 46.101 34.925 3.5 3.3 216 000 340 000 22 000 35 000 2 600 3 600 5760 5735 94 88 119 130 3.5 3.3 32.9 0.41 1.5 0.81 1.86 0.887
136.525 30.162 29.769 22.225 3.5 3.3 130 000 192 000 13 300 19 600 2 600 3 400 495 A 493 92 86 122 130 3.5 3.3 28.7 0.44 1.4 0.74 1.27 0.55
136.525 30.162 29.769 22.225 6.4 3.3 130 000 192 000 13 300 19 600 2 600 3 400 495 AX 493 98 86 122 130 6.4 3.3 28.7 0.44 1.4 0.74 1.26 0.55
139.992 36.512 36.098 28.575 3.5 3.3 175 000 260 000 17 800 26 500 2 600 3 400 575 572 92 86 125 133 3.5 3.3 31.1 0.40 1.5 0.82 1.61 0.788
149.225 53.975 54.229 44.450 3.5 3.3 287 000 410 000 29 300 41 500 2 600 3 400 6461 6420 96 89 129 140 3.5 3.3 39.0 0.36 1.7 0.91 2.64 1.63
152.400 39.688 36.322 30.162 3.5 3.2 183 000 285 000 18 700 29 100 2 200 3 200 590 A 592 A 95 89 135 145 3.5 3.2 37.1 0.44 1.4 0.75 2.2 1.06
152.400 41.275 41.275 31.750 3.5 3.3 207 000 296 000 21 100 30 000 2 400 3 200 659 652 93 87 134 141 3.5 3.3 33.2 0.41 1.5 0.81 2.11 1.26
161.925 49.212 46.038 31.750 3.5 3.3 248 000 290 000 25 300 29 600 2 200 3 000 9285 9220 103 90 138 153 3.5 3.3 49.8 0.71 0.85 0.47 2.82 1.4
161.925 53.975 55.100 42.862 3.5 3.3 325 000 480 000 33 000 49 000 2 200 3 000 6576 6535 99 92 141 154 3.5 3.3 40.7 0.40 1.5 0.82 3.74 1.67
161.925 53.975 55.100 42.862 6.4 3.3 325 000 480 000 33 000 49 000 2 200 3 000 6575 6535 104 92 141 154 6.4 3.3 40.7 0.40 1.5 0.82 3.73 1.67
161.925 53.975 55.100 42.862 6.4 0.8 325 000 480 000 33 000 49 000 2 200 3 000 6575 6536 104 92 144 154 6.4 0.8 40.7 0.40 1.5 0.82 3.73 1.68
B 158 B 159
B110-181E.indd 158-159 11/20/13 4:57:14 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
76.200 168.275 53.975 56.363 41.275 6.4 3.3 345 000 470 000 35 000 48 000 2 200 3 000 843 832 101 89 149 155 6.4 3.3 35.2 0.30 2.0 1.1 4.11 1.74
168.275 53.975 56.363 41.275 0.8 3.3 345 000 470 000 35 000 48 000 2 200 3 000 837 832 90 89 149 155 0.8 3.3 35.2 0.30 2.0 1.1 4.13 1.74
171.450 49.212 46.038 31.750 3.5 3.3 257 000 310 000 26 200 32 000 2 000 2 800 9380 9321 105 98 147 164 3.5 3.3 54.1 0.76 0.79 0.43 3.47 1.51
177.800 55.562 50.800 34.925 3.5 3.3 257 000 310 000 26 200 32 000 2 000 2 800 9378 9320 105 98 148 164 3.5 3.3 57.3 0.76 0.79 0.43 3.71 2.24
77.788 121.442 24.608 23.012 17.462 3.5 2.0 89 000 124 000 9 100 12 600 2 800 3 800 34306 34478 90 84 110 116 3.5 2 26.3 0.45 1.3 0.73 0.612 0.316
127.000 30.162 31.000 22.225 3.5 3.3 134 000 195 000 13 700 19 900 2 800 3 800 42690 42620 91 85 114 121 3.5 3.3 27.3 0.42 1.4 0.79 0.976 0.438
135.733 44.450 46.101 34.925 3.5 3.3 216 000 340 000 22 000 35 000 2 600 3 600 5795 5735 96 89 119 130 3.5 3.3 32.9 0.41 1.5 0.81 1.79 0.887
79.375 146.050 41.275 41.275 31.750 3.5 3.3 207 000 296 000 21 100 30 000 2 400 3 200 661 653 96 90 131 139 3.5 3.3 33.2 0.41 1.5 0.81 1.99 0.891
150.089 44.450 46.672 36.512 3.5 3.3 265 000 370 000 27 000 37 500 2 400 3 200 750 742 96 90 134 142 3.5 3.3 32.5 0.33 1.8 1.0 2.42 1.07
80.000 130.000 35.000 34.000 28.500 3.0 2.5 166 000 251 000 17 000 25 600 2 600 3 600 JM 515649 JM 515610 94 88 117 125 3 2.5 29.9 0.39 1.5 0.85 1.18 0.583
80.962 136.525 30.162 29.769 22.225 3.5 3.3 130 000 192 000 13 300 19 600 2 600 3 400 496 493 95 89 122 130 3.5 3.3 28.7 0.44 1.4 0.74 1.13 0.55
139.700 36.512 36.098 28.575 3.5 3.3 175 000 260 000 17 800 26 500 2 600 3 400 581 572 X 96 90 125 133 3.5 3.3 31.1 0.40 1.5 0.82 1.44 0.774
139.992 36.512 36.098 28.575 3.5 3.3 175 000 260 000 17 800 26 500 2 600 3 400 581 572 96 90 125 133 3.5 3.3 31.1 0.40 1.5 0.82 1.44 0.788
82.550 125.412 25.400 25.400 19.845 3.5 1.5 102 000 164 000 10 400 16 700 2 600 3 600 27687 27620 96 89 115 120 3.5 1.5 25.7 0.42 1.4 0.79 0.747 0.348
133.350 30.162 29.769 22.225 3.5 3.3 130 000 192 000 13 300 19 600 2 600 3 400 495 492 A 97 90 120 128 3.5 3.3 28.7 0.44 1.4 0.74 1.08 0.434
133.350 33.338 33.338 26.195 3.5 3.3 154 000 237 000 15 700 24 200 2 600 3 600 47686 47620 97 90 119 128 3.5 3.3 29.0 0.40 1.5 0.82 1.18 0.577
133.350 33.338 33.338 26.195 0.8 3.3 154 000 237 000 15 700 24 200 2 600 3 600 47685 47620 90 90 119 128 0.8 3.3 29.0 0.40 1.5 0.82 1.18 0.577
133.350 33.338 33.338 26.195 6.8 3.3 154 000 237 000 15 700 24 200 2 600 3 600 47687 47620 103 90 119 128 6.8 3.3 29.0 0.40 1.5 0.82 1.16 0.577
133.350 39.688 39.688 32.545 6.8 3.3 179 000 310 000 18 300 31 500 2 600 3 600 HM 516448 HM 516410 105 92 118 128 6.8 3.3 32.4 0.40 1.5 0.82 1.35 0.767
136.525 30.162 29.769 22.225 3.5 3.3 130 000 192 000 13 300 19 600 2 600 3 400 495 493 97 90 122 130 3.5 3.3 28.7 0.44 1.4 0.74 1.08 0.55
139.700 36.512 36.098 28.575 3.5 3.3 175 000 260 000 17 800 26 500 2 600 3 400 580 572 X 98 91 125 133 3.5 3.3 31.1 0.40 1.5 0.82 1.39 0.774
139.992 36.512 36.098 28.575 3.5 3.3 175 000 260 000 17 800 26 500 2 600 3 400 580 572 98 91 125 133 3.5 3.3 31.1 0.40 1.5 0.82 1.39 0.788
139.992 36.512 36.098 28.575 6.8 3.3 175 000 260 000 17 800 26 500 2 600 3 400 582 572 104 91 125 133 6.8 3.3 31.1 0.40 1.5 0.82 1.37 0.788
146.050 41.275 41.275 31.750 3.5 3.3 207 000 296 000 21 100 30 000 2 400 3 200 663 653 99 92 131 139 3.5 3.3 33.2 0.41 1.5 0.81 1.85 0.891
150.000 44.455 46.672 35.000 3.5 3.3 265 000 370 000 27 000 37 500 2 400 3 200 749 A 743 99 93 134 142 3.5 3.3 32.5 0.33 1.8 1.0 2.26 1.04
150.089 44.450 46.672 36.512 3.5 3.3 265 000 370 000 27 000 37 500 2 400 3 200 749 A 742 98 93 135 143 3.5 3.3 32.5 0.33 1.8 1.0 2.26 1.07
152.400 41.275 41.275 31.750 3.5 3.3 207 000 296 000 21 100 30 000 2 400 3 200 663 652 99 92 134 141 3.5 3.3 33.2 0.41 1.5 0.81 1.85 1.26
161.925 47.625 48.260 38.100 3.5 3.3 274 000 390 000 28 000 40 000 2 200 3 000 757 752 100 94 144 150 3.5 3.3 35.6 0.34 1.8 0.97 2.79 1.61
161.925 53.975 55.100 42.862 3.5 3.3 325 000 480 000 33 000 49 000 2 200 3 000 6559 6535 104 98 141 154 3.5 3.3 40.7 0.40 1.5 0.82 3.4 1.67
168.275 47.625 48.260 38.100 3.5 3.3 274 000 390 000 28 000 40 000 2 200 3 000 757 753 100 94 147 150 3.5 3.3 35.6 0.34 1.8 0.97 2.79 2.1
168.275 53.975 56.363 41.275 3.5 3.3 345 000 470 000 35 000 48 000 2 200 3 000 842 832 101 94 149 155 3.5 3.3 35.2 0.30 2.0 1.1 3.76 1.74
83.345 125.412 25.400 25.400 19.845 3.5 1.5 102 000 164 000 10 400 16 700 2 600 3 600 27690 27620 96 90 115 120 3.5 1.5 25.7 0.42 1.4 0.79 0.727 0.348
125.412 25.400 25.400 19.845 0.8 1.5 102 000 164 000 10 400 16 700 2 600 3 600 27689 27620 90 90 115 120 0.8 1.5 25.7 0.42 1.4 0.79 0.732 0.348
B 160 B 161
B110-181E.indd 160-161 11/20/13 4:57:15 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
84.138 136.525 30.162 29.769 22.225 3.5 3.3 130 000 192 000 13 300 19 600 2 600 3 400 498 493 98 91 122 130 3.5 3.3 28.7 0.44 1.4 0.74 1.04 0.55
146.050 41.275 41.275 31.750 3.5 3.3 207 000 296 000 21 100 30 000 2 400 3 200 664 653 99 93 131 139 3.5 3.3 33.2 0.41 1.5 0.81 1.79 0.891
171.450 49.212 46.038 31.750 3.5 3.3 257 000 310 000 26 200 32 000 2 000 2 800 9385 9321 111 98 147 164 3.5 3.3 54.1 0.76 0.79 0.43 3.11 1.51
85.000 130.000 30.000 29.000 24.000 6.0 2.5 138 000 222 000 14 100 22 700 2 600 3 600 JM 716648 JM 716610 104 92 117 125 6 2.5 29.5 0.44 1.4 0.74 0.931 0.461
130.000 30.000 29.000 24.000 3.0 2.5 138 000 222 000 14 100 22 700 2 600 3 600 JM 716649 JM 716610 98 92 117 125 3 2.5 29.5 0.44 1.4 0.74 0.943 0.461
140.000 39.000 38.000 31.500 3.0 2.5 202 000 305 000 20 600 31 000 2 400 3 400 JHM 516849 JHM 516810 100 94 125 134 3 2.5 33.3 0.41 1.5 0.81 1.55 0.768
150.000 46.000 46.000 38.000 3.0 2.5 275 000 390 000 28 000 40 000 2 400 3 200 JH 217249 JH 217210 101 95 134 142 3 2.5 33.9 0.33 1.8 0.99 2.29 1.09
85.026 150.089 44.450 46.672 36.512 3.5 3.3 265 000 370 000 27 000 37 500 2 400 3 200 749 742 101 95 134 142 3.5 3.3 32.5 0.33 1.8 1.0 2.14 1.07
150.089 44.450 46.672 36.512 5.0 3.3 265 000 370 000 27 000 37 500 2 400 3 200 749 S 742 104 95 134 142 5 3.3 32.5 0.33 1.8 1.0 2.14 1.07
85.725 133.350 30.162 29.769 22.225 3.5 3.3 130 000 192 000 13 300 19 600 2 600 3 400 497 492 A 99 93 120 128 3.5 3.3 28.7 0.44 1.4 0.74 0.987 0.434
136.525 30.162 29.769 22.225 3.5 3.3 130 000 192 000 13 300 19 600 2 600 3 400 497 493 99 93 122 130 3.5 3.3 28.7 0.44 1.4 0.74 0.987 0.55
142.138 42.862 42.862 34.133 4.8 3.3 221 000 360 000 22 500 36 500 2 400 3 400 HM 617049 HM 617010 106 95 125 137 4.8 3.3 35.4 0.43 1.4 0.76 1.77 0.911
146.050 41.275 41.275 31.750 6.4 3.3 207 000 296 000 21 100 30 000 2 400 3 200 665 A 653 107 95 131 139 6.4 3.3 33.2 0.41 1.5 0.81 1.71 0.891
146.050 41.275 41.275 31.750 3.5 3.3 207 000 296 000 21 100 30 000 2 400 3 200 665 653 102 95 131 139 3.5 3.3 33.2 0.41 1.5 0.81 1.72 0.891
152.400 39.688 36.322 30.162 3.5 3.2 183 000 285 000 18 700 29 100 2 200 3 200 596 592 A 102 96 135 144 3.5 3.2 37.1 0.44 1.4 0.75 1.85 1.06
161.925 47.625 48.260 38.100 3.5 3.3 274 000 390 000 28 000 40 000 2 200 3 000 758 752 103 97 144 150 3.5 3.3 35.6 0.34 1.8 0.97 2.63 1.61
168.275 41.275 41.275 30.162 3.5 3.3 223 000 345 000 22 700 35 000 2 000 2 800 677 672 105 99 149 160 3.5 3.3 38.3 0.47 1.3 0.70 2.91 1.24
87.312 190.500 57.150 57.531 46.038 8.0 3.3 390 000 520 000 39 500 53 500 1 900 2 600 HH 221432 HH 221410 118 103 171 179 8 3.3 42.3 0.33 1.8 0.99 5.51 2.24
88.900 149.225 31.750 28.971 24.608 3.0 3.3 140 000 218 000 14 300 22 300 2 200 3 000 42350 42587 104 98 134 143 3 3.3 34.9 0.49 1.2 0.67 1.39 0.711
152.400 39.688 36.322 30.162 3.5 3.2 183 000 285 000 18 700 29 100 2 200 3 200 593 592 A 104 98 135 144 3.5 3.2 37.1 0.44 1.4 0.75 1.73 1.06
152.400 39.688 39.688 30.162 6.4 3.3 253 000 365 000 25 800 37 500 2 200 3 200 HM 518445 HM 518410 107 96 137 148 6.4 3.3 33.1 0.40 1.5 0.82 2.11 0.776
161.925 47.625 48.260 38.100 3.5 3.3 274 000 390 000 28 000 40 000 2 200 3 000 759 752 106 99 144 150 3.5 3.3 35.6 0.34 1.8 0.97 2.47 1.61
161.925 47.625 48.260 38.100 7.0 3.3 274 000 390 000 28 000 40 000 2 200 3 000 766 752 113 99 144 150 7 3.3 35.6 0.34 1.8 0.97 2.45 1.61
161.925 53.975 55.100 42.862 3.5 3.3 325 000 480 000 33 000 49 000 2 200 3 000 6580 6535 109 102 141 154 3.5 3.3 40.7 0.40 1.5 0.82 3.03 1.67
168.275 47.625 48.260 38.100 3.5 3.3 274 000 390 000 28 000 40 000 2 200 3 000 759 753 106 99 147 150 3.5 3.3 35.6 0.34 1.8 0.97 2.47 2.1
168.275 53.975 56.363 41.275 3.5 3.3 345 000 470 000 35 000 48 000 2 200 3 000 850 832 106 100 149 155 3.5 3.3 35.2 0.30 2.0 1.1 3.39 1.74
190.500 57.150 57.531 44.450 8.0 3.3 355 000 500 000 36 000 51 000 1 900 2 600 855 854 118 103 170 174 8 3.3 41.8 0.33 1.8 0.99 4.99 2.55
190.500 57.150 57.531 46.038 8.0 3.3 390 000 520 000 39 500 53 500 1 900 2 600 HH 221434 HH 221410 120 105 171 179 8 3.3 42.3 0.33 1.8 0.99 5.41 2.24
90.000 145.000 35.000 34.000 27.000 3.0 2.5 190 000 285 000 19 400 29 000 2 400 3 200 JM 718149 JM 718110 105 99 131 139 3 2.5 33.0 0.44 1.4 0.74 1.49 0.66
147.000 40.000 40.000 32.500 7.0 3.5 229 000 345 000 23 400 35 000 2 400 3 200 *HM 218248 **HM 218210 111 98 133 141 7 3.5 30.8 0.33 1.8 0.99 1.77 0.796
155.000 44.000 44.000 35.500 3.0 2.5 274 000 395 000 28 000 40 000 2 200 3 000 JHM 318448 JHM 318410 106 100 140 148 3 2.5 34.1 0.34 1.7 0.96 2.32 1.01
90.488 161.925 47.625 48.260 38.100 3.5 3.3 274 000 390 000 28 000 40 000 2 200 3 000 760 752 107 101 144 150 3.5 3.3 35.6 0.34 1.8 0.97 2.38 1.61
B 162 B 163
B110-181E.indd 162-163 11/20/13 4:57:16 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
92.075 146.050 33.338 34.925 26.195 3.5 3.3 169 000 280 000 17 300 28 500 2 400 3 200 47890 47820 107 101 131 140 3.5 3.3 32.3 0.45 1.3 0.74 1.46 0.664
148.430 28.575 28.971 21.433 3.5 3.0 140 000 218 000 14 300 22 300 2 200 3 000 42362 42584 107 101 134 142 3.5 3 31.8 0.49 1.2 0.67 1.29 0.553
152.400 39.688 36.322 30.162 3.5 3.2 183 000 285 000 18 700 29 100 2 200 3 200 598 592 A 107 101 135 144 3.5 3.2 37.1 0.44 1.4 0.75 1.6 1.06
152.400 39.688 36.322 30.162 6.4 3.2 183 000 285 000 18 700 29 100 2 200 3 200 598 A 592 A 113 101 135 144 6.4 3.2 37.1 0.44 1.4 0.75 1.59 1.06
168.275 41.275 41.275 30.162 3.5 3.3 223 000 345 000 22 700 35 000 2 000 2 800 681 672 110 104 149 160 3.5 3.3 38.3 0.47 1.3 0.70 2.62 1.24
190.500 57.150 57.531 44.450 8.0 3.3 355 000 500 000 36 000 51 000 1 900 2 600 857 854 121 106 170 174 8 3.3 41.8 0.33 1.8 0.99 4.78 2.55
93.662 148.430 28.575 28.971 21.433 3.0 3.0 140 000 218 000 14 300 22 300 2 200 3 000 42368 42584 107 102 134 142 3 3 31.8 0.49 1.2 0.67 1.24 0.553
149.225 31.750 28.971 24.608 3.0 3.3 140 000 218 000 14 300 22 300 2 200 3 000 42368 42587 107 102 134 143 3 3.3 34.9 0.49 1.2 0.67 1.24 0.711
152.400 39.688 36.322 30.162 3.5 3.2 183 000 285 000 18 700 29 100 2 200 3 200 597 592 A 109 102 135 144 3.5 3.2 37.1 0.44 1.4 0.75 1.54 1.06
95.000 150.000 35.000 34.000 27.000 3.0 2.5 183 000 285 000 18 700 29 100 2 200 3 200 JM 719149 JM 719113 109 104 135 143 3 2.5 33.4 0.44 1.4 0.75 1.46 0.765
95.250 146.050 33.338 34.925 26.195 3.5 3.3 169 000 280 000 17 300 28 500 2 400 3 200 47896 47820 110 103 131 140 3.5 3.3 32.3 0.45 1.3 0.74 1.33 0.664
148.430 28.575 28.971 21.433 3.0 3.0 140 000 218 000 14 300 22 300 2 200 3 000 42375 42584 108 103 134 142 3 3 31.8 0.49 1.2 0.67 1.18 0.553
149.225 31.750 28.971 24.608 3.5 3.3 140 000 218 000 14 300 22 300 2 200 3 000 42376 42587 109 103 134 143 3.5 3.3 34.9 0.49 1.2 0.67 1.18 0.711
152.400 39.688 36.322 30.162 3.5 3.2 183 000 285 000 18 700 29 100 2 200 3 200 594 592 A 110 104 135 144 3.5 3.2 37.1 0.44 1.4 0.75 1.47 1.06
152.400 39.688 36.322 33.338 3.5 3.3 183 000 285 000 18 700 29 100 2 200 3 200 594 592 109 103 135 145 3.5 3.3 37.1 0.44 1.4 0.75 1.47 1.12
168.275 41.275 41.275 30.162 3.5 3.3 223 000 345 000 22 700 35 000 2 000 2 800 683 672 113 106 149 160 3.5 3.3 38.3 0.47 1.3 0.70 2.47 1.24
171.450 47.625 48.260 38.100 3.5 3.3 282 000 415 000 28 800 42 500 2 000 2 800 77375 77675 117 105 152 159 3.5 3.3 37.8 0.37 1.6 0.90 2.91 1.67
180.975 47.625 48.006 38.100 3.5 3.3 258 000 375 000 26 300 38 500 2 000 2 600 776 772 114 107 161 168 3.5 3.3 39.1 0.39 1.6 0.86 3.25 1.99
190.500 57.150 57.531 44.450 8.0 3.3 355 000 500 000 36 000 51 000 1 900 2 600 864 854 123 108 170 174 8 3.3 41.8 0.33 1.8 0.99 4.57 2.55
190.500 57.150 57.531 46.038 8.0 3.3 390 000 520 000 39 500 53 500 1 900 2 600 HH 221440 HH 221410 125 110 171 179 8 3.3 42.3 0.33 1.8 0.99 5.0 2.24
96.838 148.430 28.575 28.971 21.433 3.5 3.0 140 000 218 000 14 300 22 300 2 200 3 000 42381 42584 110 104 134 142 3.5 3 31.8 0.49 1.2 0.67 1.13 0.553
149.225 31.750 28.971 24.606 3.5 3.3 140 000 218 000 14 300 22 300 2 200 3 000 42381 42587 111 105 135 143 3.5 3.3 34.9 0.49 1.2 0.67 1.13 0.711
98.425 161.925 36.512 36.116 26.195 3.5 3.3 191 000 310 000 19 500 31 500 2 000 2 800 52387 52637 114 108 144 154 3.5 3.3 36.1 0.47 1.3 0.69 1.89 0.942
168.275 41.275 41.275 30.162 3.5 3.3 223 000 345 000 22 700 35 000 2 000 2 800 685 672 116 109 149 160 3.5 3.3 38.3 0.47 1.3 0.70 2.32 1.24
180.975 47.625 48.006 38.100 3.5 3.3 258 000 375 000 26 300 38 500 2 000 2 600 779 772 116 110 161 168 3.5 3.3 39.1 0.39 1.6 0.86 3.06 1.99
190.500 57.150 57.531 44.450 3.5 3.3 355 000 500 000 36 000 51 000 1 900 2 600 866 854 118 111 170 174 3.5 3.3 41.8 0.33 1.8 0.99 4.38 2.55
190.500 57.150 57.531 46.038 3.5 3.3 390 000 520 000 39 500 53 500 1 900 2 600 HH 221442 HH 221410 119 113 171 179 3.5 3.3 42.3 0.33 1.8 0.99 4.81 2.24
99.982 190.500 57.150 57.531 46.038 6.4 3.3 390 000 520 000 39 500 53 500 1 900 2 600 HH 221447 HH 221410 126 114 171 179 6.4 3.3 42.3 0.33 1.8 0.99 4.68 2.24
100.000 150.000 32.000 30.000 26.000 2.3 2.3 146 000 235 000 14 900 24 000 2 200 3 000 JLM 820048 JLM 820012 111 107 135 144 2.3 2.3 36.8 0.50 1.2 0.66 1.27 0.616
155.000 36.000 35.000 28.000 3.0 2.5 191 000 325 000 19 500 33 000 2 000 2 800 JM 720249 JM 720210 115 109 140 149 3 2.5 36.8 0.47 1.3 0.70 1.68 0.772
160.000 41.000 40.000 32.000 3.0 2.5 239 000 380 000 24 400 38 500 2 000 2 800 JHM 720249 JHM 720210 117 109 143 154 3 2.5 38.2 0.47 1.3 0.70 2.09 0.974
100.012 157.162 36.512 36.116 26.195 3.5 3.3 191 000 310 000 19 500 31 500 2 000 2 800 52393 52618 116 109 142 152 3.5 3.3 36.1 0.47 1.3 0.69 1.81 0.702
B 164 B 165
B110-181E.indd 164-165 11/20/13 4:57:17 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
101.600 157.162 36.512 36.116 26.195 3.5 3.3 191 000 310 000 19 500 31 500 2 000 2 800 52400 52618 117 111 142 152 3.5 3.3 36.1 0.47 1.3 0.69 1.75 0.702
161.925 36.512 36.116 26.195 3.5 3.3 191 000 310 000 19 500 31 500 2 000 2 800 52400 52637 117 111 144 154 3.5 3.3 36.1 0.47 1.3 0.69 1.75 0.942
168.275 41.275 41.275 30.162 3.5 3.3 223 000 345 000 22 700 35 000 2 000 2 800 687 672 118 112 149 160 3.5 3.3 38.3 0.47 1.3 0.70 2.15 1.24
180.975 47.625 48.006 38.100 3.5 3.3 258 000 375 000 26 300 38 500 2 000 2 600 780 772 119 113 161 168 3.5 3.3 39.1 0.39 1.6 0.86 2.88 1.99
190.500 57.150 57.531 44.450 8.0 3.3 355 000 500 000 36 000 51 000 1 900 2 600 861 854 129 114 170 174 8 3.3 41.8 0.33 1.8 0.99 4.13 2.55
190.500 57.150 57.531 46.038 8.0 3.3 390 000 520 000 39 500 53 500 1 900 2 600 HH 221449 HH 221410 131 116 171 179 8 3.3 42.3 0.33 1.8 0.99 4.55 2.24
212.725 66.675 66.675 53.975 7.0 3.3 570 000 810 000 58 000 82 500 1 700 2 200 HH 224335 HH 224310 132 121 192 202 7 3.3 47.3 0.33 1.8 1.0 8.14 3.06
104.775 180.975 47.625 48.006 38.100 7.0 3.3 258 000 375 000 26 300 38 500 2 000 2 600 787 772 129 116 161 168 7 3.3 39.1 0.39 1.6 0.86 2.66 1.99
180.975 47.625 48.006 38.100 3.5 3.3 258 000 375 000 26 300 38 500 2 000 2 600 782 772 122 116 161 168 3.5 3.3 39.1 0.39 1.6 0.86 2.68 1.99
190.500 47.625 49.212 34.925 3.5 3.3 296 000 465 000 30 000 47 000 1 800 2 400 71412 71750 124 118 171 181 3.5 3.3 40.1 0.42 1.4 0.79 4.0 1.71
106.362 165.100 36.512 36.512 26.988 3.5 3.3 195 000 320 000 19 800 33 000 2 000 2 600 56418 56650 122 116 149 159 3.5 3.3 38.6 0.50 1.2 0.66 1.87 0.861
107.950 158.750 23.020 21.438 15.875 3.5 3.3 102 000 165 000 10 400 16 800 2 000 2 800 37425 37625 122 115 143 152 3.5 3.3 37.0 0.61 0.99 0.54 0.886 0.488
159.987 34.925 34.925 26.988 3.5 3.3 164 000 315 000 16 700 32 000 2 000 2 800 LM 522546 LM 522510 122 116 146 154 3.5 3.3 33.7 0.40 1.5 0.82 1.65 0.784
161.925 34.925 34.925 26.988 3.5 3.3 164 000 280 000 16 800 28 600 2 000 2 800 48190 48120 122 116 146 156 3.5 3.3 38.7 0.51 1.2 0.65 1.59 0.83
165.100 36.512 36.512 26.988 3.5 3.3 195 000 320 000 19 800 33 000 2 000 2 600 56425 56650 123 117 149 159 3.5 3.3 38.6 0.50 1.2 0.66 1.8 0.861
190.500 47.625 49.212 34.925 3.5 3.3 296 000 465 000 30 000 47 000 1 800 2 400 71425 71750 126 120 171 181 3.5 3.3 40.1 0.42 1.4 0.79 3.79 1.71
212.725 66.675 66.675 53.975 8.0 3.3 570 000 810 000 58 000 82 500 1 700 2 200 HH 224340 HH 224310 139 126 192 202 8 3.3 47.3 0.33 1.8 1.0 7.58 3.06
109.987 159.987 34.925 34.925 26.988 3.5 3.3 164 000 315 000 16 700 32 000 2 000 2 800 LM 522549 LM 522510 124 118 146 154 3.5 3.3 33.7 0.40 1.5 0.82 1.55 0.784
159.987 34.925 34.925 26.988 8.0 3.3 164 000 315 000 16 700 32 000 2 000 2 800 LM 522548 LM 522510 133 118 146 154 8 3.3 33.7 0.40 1.5 0.82 1.53 0.784
109.992 177.800 41.275 41.275 30.162 3.5 3.3 232 000 375 000 23 700 38 000 1 800 2 600 64433 64700 128 121 160 172 3.5 3.3 42.4 0.52 1.2 0.64 2.64 1.11
110.000 165.000 35.000 35.000 26.500 3.0 2.5 195 000 320 000 19 800 33 000 2 000 2 600 JM 822049 JM 822010 124 119 149 159 3 2.5 38.3 0.50 1.2 0.66 1.64 0.842
180.000 47.000 46.000 38.000 3.0 2.5 310 000 490 000 31 500 50 000 1 900 2 600 JHM 522649 JHM 522610 127 122 162 172 3 2.5 40.9 0.41 1.5 0.81 3.12 1.51
111.125 190.500 47.625 49.212 34.925 3.5 3.3 296 000 465 000 30 000 47 000 1 800 2 400 71437 71750 129 123 171 181 3.5 3.3 40.1 0.42 1.4 0.79 3.58 1.71
114.300 152.400 21.433 21.433 16.670 1.5 1.5 89 500 178 000 9 100 18 100 2 000 2 800 L 623149 L 623110 123 121 143 148 1.5 1.5 27.4 0.41 1.5 0.80 0.725 0.344
177.800 41.275 41.275 30.162 3.5 3.3 232 000 375 000 23 700 38 000 1 800 2 600 64450 64700 131 125 160 172 3.5 3.3 42.4 0.52 1.2 0.64 2.39 1.11
180.000 34.925 31.750 25.400 3.5 0.8 174 000 254 000 17 800 25 900 1 800 2 400 68450 ** 68709 130 123 165 172 3.5 0.8 40.0 0.50 1.2 0.66 1.95 1.0
190.500 47.625 49.212 34.925 3.5 3.3 296 000 465 000 30 000 47 000 1 800 2 400 71450 71750 132 125 171 181 3.5 3.3 40.1 0.42 1.4 0.79 3.37 1.71
212.725 66.675 66.675 53.975 7.0 3.3 475 000 700 000 48 500 71 500 1 700 2 400 938 932 141 128 187 193 7 3.3 46.9 0.33 1.8 1.0 6.01 4.11
212.725 66.675 66.675 53.975 7.0 3.3 570 000 810 000 58 000 82 500 1 700 2 200 HH 224346 HH 224310 143 131 192 202 7 3.3 47.3 0.33 1.8 1.0 7.01 3.06
115.087 190.500 47.625 49.212 34.925 3.5 3.3 296 000 465 000 30 000 47 000 1 800 2 400 71453 71750 133 126 171 181 3.5 3.3 40.1 0.42 1.4 0.79 3.31 1.71
117.475 180.975 34.925 31.750 25.400 3.5 3.3 174 000 254 000 17 800 25 900 1 800 2 400 68462 68712 132 125 163 172 3.5 3.3 40.0 0.50 1.2 0.66 1.73 1.05
Notes ** The maximum outside diameter is listed and its tolerance is negative (See Table 8.4.2 on Pages A68 and A69).
B 166 B 167
B110-181E.indd 166-167 11/20/13 4:57:18 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
120.000 170.000 25.400 25.400 19.050 3.3 3.3 130 000 219 000 13 200 22 300 1 900 2 600 JL 724348 JL 724314 132 127 156 163 3.3 3.3 32.9 0.46 1.3 0.72 1.08 0.591
174.625 35.720 36.512 27.783 3.5 1.5 212 000 385 000 21 600 39 000 1 900 2 600 * M 224748 M 224710 135 129 163 168 3.5 1.5 32.2 0.33 1.8 0.99 1.9 0.866
120.650 182.562 39.688 38.100 33.338 3.5 3.3 228 000 445 000 23 200 45 000 1 800 2 400 48282 48220 136 133 168 176 3.5 3.3 34.2 0.31 2.0 1.1 2.56 1.14
206.375 47.625 47.625 34.925 3.3 3.3 320 000 530 000 32 500 54 000 1 600 2 200 795 792 139 134 186 198 3.3 3.3 45.7 0.46 1.3 0.72 4.44 1.9
123.825 182.562 39.688 38.100 33.338 3.5 3.3 228 000 445 000 23 200 45 000 1 800 2 400 48286 48220 139 133 168 176 3.5 3.3 34.2 0.31 2.0 1.1 2.37 1.14
125.000 175.000 25.400 25.400 18.288 3.3 3.3 134 000 232 000 13 700 23 600 1 800 2 400 JL 725346 JL 725316 138 133 161 168 3.3 3.3 34.3 0.48 1.3 0.69 1.19 0.573
127.000 165.895 18.258 17.462 13.495 1.5 1.5 84 500 149 000 8 650 15 200 1 900 2 600 LL 225749 LL 225710 135 132 158 160 1.5 1.5 24.2 0.33 1.8 0.99 0.647 0.288
182.562 39.688 38.100 33.338 3.5 3.3 228 000 445 000 23 200 45 000 1 800 2 400 48290 48220 141 135 168 176 3.5 3.3 34.2 0.31 2.0 1.1 2.19 1.14
196.850 46.038 46.038 38.100 3.5 3.3 315 000 560 000 32 000 57 500 1 700 2 200 67388 67322 144 138 180 189 3.5 3.3 39.7 0.34 1.7 0.96 3.74 1.46
215.900 47.625 47.625 34.925 3.5 3.3 287 000 495 000 29 300 50 000 1 500 2 000 74500 74850 148 141 196 208 3.5 3.3 48.4 0.49 1.2 0.68 4.92 1.99
128.588 206.375 47.625 47.625 34.925 3.3 3.3 320 000 530 000 32 500 54 000 1 600 2 200 799 792 146 140 186 198 3.3 3.3 45.7 0.46 1.3 0.72 3.86 1.9
130.000 206.375 47.625 47.625 34.925 3.5 3.3 320 000 530 000 32 500 54 000 1 600 2 200 797 792 148 141 186 198 3.5 3.3 45.7 0.46 1.3 0.72 3.76 1.9
130.175 203.200 46.038 46.038 38.100 3.5 3.3 315 000 560 000 32 000 57 500 1 700 2 200 67389 67320 146 141 183 191 3.5 3.3 39.7 0.34 1.7 0.96 3.51 2.06
206.375 47.625 47.625 34.925 3.5 3.3 320 000 530 000 32 500 54 000 1 600 2 200 799 A 792 148 142 186 198 3.5 3.3 45.7 0.46 1.3 0.72 3.74 1.9
133.350 177.008 25.400 26.195 20.638 1.5 1.5 124 000 258 000 12 700 26 300 1 800 2 400 L 327249 L 327210 143 141 167 171 1.5 1.5 29.5 0.35 1.7 0.95 1.18 0.55
190.500 39.688 39.688 33.338 3.5 3.3 240 000 485 000 24 500 49 500 1 700 2 200 48385 48320 148 142 177 184 3.5 3.3 35.9 0.32 1.9 1.0 2.58 1.16
196.850 46.038 46.038 38.100 3.5 3.3 315 000 560 000 32 000 57 500 1 700 2 200 67390 67322 149 143 180 189 3.5 3.3 39.7 0.34 1.7 0.96 3.27 1.46
215.900 47.625 47.625 34.925 3.5 3.3 287 000 495 000 29 300 50 000 1 500 2 000 74525 74850 152 146 196 208 3.5 3.3 48.4 0.49 1.2 0.68 4.44 1.99
136.525 190.500 39.688 39.688 33.338 3.5 3.3 216 000 440 000 22 000 45 000 1 700 2 200 48393 48320 151 144 177 184 3.5 3.3 35.9 0.32 1.9 1.0 2.31 1.16
217.488 47.625 47.625 34.925 3.5 3.3 287 000 495 000 29 300 50 000 1 500 2 000 74537 74856 155 148 197 210 3.5 3.3 48.4 0.49 1.2 0.68 4.19 2.13
139.700 187.325 28.575 29.370 23.020 1.5 1.5 153 000 305 000 15 600 31 500 1 700 2 200 LM 328448 LM 328410 149 147 176 182 1.5 1.5 31.7 0.36 1.7 0.93 1.59 0.67
215.900 47.625 47.625 34.925 3.5 3.3 287 000 495 000 29 300 50 000 1 500 2 000 74550 74850 158 151 196 208 3.5 3.3 48.4 0.49 1.2 0.68 3.93 1.99
254.000 66.675 66.675 47.625 7.0 3.3 515 000 830 000 52 500 84 500 1 300 1 800 99550 99100 170 156 227 238 7 3.3 55.3 0.41 1.5 0.81 9.99 3.83
142.875 200.025 41.275 39.688 34.130 3.5 3.3 227 000 460 000 23 100 46 500 1 600 2 200 48685 48620 158 151 185 193 3.5 3.3 37.6 0.34 1.8 0.98 2.63 1.19
146.050 193.675 28.575 28.575 23.020 1.5 1.5 170 000 355 000 17 300 36 500 1 600 2 200 36690 36620 155 154 182 188 1.5 1.5 33.5 0.37 1.6 0.90 1.64 0.725
236.538 57.150 56.642 44.450 3.5 3.3 455 000 720 000 46 000 73 500 1 400 1 900 HM 231140 HM 231110 164 160 217 224 3.5 3.3 45.9 0.32 1.9 1.0 6.07 2.93
254.000 66.675 66.675 47.625 7.0 3.3 515 000 830 000 52 500 84 500 1 300 1 800 99575 99100 175 162 227 238 7 3.3 55.3 0.41 1.5 0.81 9.24 3.83
149.225 254.000 66.675 66.675 47.625 7.0 3.3 515 000 830 000 52 500 84 500 1 300 1 800 99587 99100 178 165 227 238 7 3.3 55.3 0.41 1.5 0.81 8.86 3.83
152.400 254.000 66.675 66.675 47.625 7.0 3.3 515 000 830 000 52 500 84 500 1 300 1 800 99600 99100 181 167 227 238 7 3.3 55.3 0.41 1.5 0.81 8.46 3.83
158.750 225.425 41.275 39.688 33.338 3.5 3.3 240 000 540 000 24 400 55 000 1 400 1 900 46780 46720 176 169 209 218 3.5 3.3 44.3 0.38 1.6 0.86 3.69 1.66
165.100 247.650 47.625 47.625 38.100 3.5 3.3 345 000 705 000 35 500 71 500 1 300 1 700 67780 67720 185 179 229 240 3.5 3.3 52.4 0.44 1.4 0.75 5.83 2.33
B 168 B 169
B110-181E.indd 168-169 11/20/13 4:57:19 PM

T
C
r ra
P =X Fr +Y Fa

B X Y X Y
P0 = 0.5Fr +Y0 Fa
min. max. CONE CUP
170.000 230.000 39.000 38.000 31.000 3.0 2.5 278 000 520 000 28 300 53 000 1 300 1 800 JHM 534149 JHM 534110 184 178 217 224 3 2.5 43.2 0.38 1.6 0.86 3.1 1.3
240.000 46.000 44.500 37.000 3.0 2.5 380 000 720 000 39 000 73 000 1 300 1 800 JM 734449 JM 734410 185 180 222 232 3 2.5 50.5 0.44 1.4 0.75 4.42 2.02
174.625 247.650 47.625 47.625 38.100 3.5 3.3 345 000 705 000 35 500 71 500 1 300 1 700 67787 67720 192 185 229 240 3.5 3.3 52.4 0.44 1.4 0.75 4.88 2.33
177.800 227.012 30.162 30.162 23.020 1.5 1.5 181 000 415 000 18 500 42 000 1 300 1 800 36990 36920 189 186 214 221 1.5 1.5 42.9 0.44 1.4 0.75 2.1 0.907
247.650 47.625 47.625 38.100 3.5 3.3 345 000 705 000 35 500 71 500 1 300 1 700 67790 67720 194 188 229 240 3.5 3.3 52.4 0.44 1.4 0.75 4.56 2.33
260.350 53.975 53.975 41.275 3.5 3.3 455 000 835 000 46 500 85 000 1 200 1 700 M 236849 M 236810 195 192 241 249 3.5 3.3 47.5 0.33 1.8 0.99 6.49 2.86
190.000 260.000 46.000 44.000 36.500 3.0 2.5 370 000 730 000 38 000 74 500 1 100 1 600 JM 738249 JM 738210 206 200 242 252 3 2.5 56.4 0.48 1.3 0.69 4.73 2.2
190.500 266.700 47.625 46.833 38.100 3.5 3.3 345 000 720 000 35 000 73 000 1 100 1 500 67885 67820 209 203 246 259 3.5 3.3 57.9 0.48 1.3 0.69 5.4 2.64
200.000 300.000 65.000 62.000 51.000 3.5 2.5 615 000 1 130 000 62 500 116 000 1 000 1 400 JHM 840449 JHM 840410 223 215 273 289 3.5 2.5 73.1 0.52 1.2 0.63 10.3 5.19
203.200 282.575 46.038 46.038 36.512 3.5 3.3 365 000 800 000 37 500 81 500 1 000 1 400 67983 67920 222 216 260 275 3.5 3.3 61.9 0.51 1.2 0.65 6.03 2.82
206.375 282.575 46.038 46.038 36.512 3.5 3.3 365 000 800 000 37 500 81 500 1 000 1 400 67985 67920 224 219 260 275 3.5 3.3 61.9 0.51 1.2 0.65 5.66 2.82
B 170 B 171
B110-181E.indd 170-171 11/20/13 4:57:20 PM

B2
C
r1 rb
r Dynamic Equivalent Load

ra
P = X Fr +Y Fa
jD jd jD b jd a Fa/ Fre Fa/ Fr>e

X Y X Y
1 Y3 0.67 Y2
P0 =Fr +Y0 Fa
The values of e, Y2 , Y3 , and Y0 are
Boundary Dimensions Basic Load Ratings Abutment and Fillet Dimensions Constant Axial Load Mass
Limiting Speeds (min1)
(mm) (N) (mm) Factors (kg)
Grease Oil Bearing Numbers
d D B2 C r r1 Cr C 0r da Db ra rb e Y2 Y3 Y0
min. min. min. min. max. max. approx.
40 80 45 37.5 1.5 0.6 109 000 140 000 3 700 5 100 HR 40 KBE 42+L 51 75 1.5 0.6 0.37 2.7 1.8 1.8 0.97
45 85 47 37.5 1.5 0.6 117 000 159 000 3 400 4 700 HR 45 KBE 42+L 56 81 1.5 0.6 0.40 2.5 1.7 1.6 1.08
85 55 43.5 1.5 0.6 143 000 204 000 3 400 4 700 HR 45 KBE 52X+L 56 81 1.5 0.6 0.40 2.5 1.7 1.6 1.31
50 90 48 38.5 1.5 0.6 131 000 183 000 3 200 4 400 HR 50 KBE 042+L 61 87 1.5 0.6 0.42 2.4 1.6 1.6 1.20
90 49 39.5 1.5 0.6 131 000 183 000 3 200 4 400 HR 50 KBE 42+L 61 87 1.5 0.6 0.42 2.4 1.6 1.6 1.22
90 55 43.5 1.5 0.6 150 000 218 000 3 200 4 400 HR 50 KBE 52X+L 61 87 1.5 0.6 0.42 2.4 1.6 1.6 1.39
110 64 51.5 2.5 0.6 224 000 297 000 2 700 3 700 HR 50 KBE 043+L 65 104 2 0.6 0.35 2.9 2.0 1.9 2.77
55 100 51 41.5 2 0.6 162 000 226 000 2 900 3 900 HR 55 KBE 042+L 67 96 2 0.6 0.40 2.5 1.7 1.6 1.59
100 52 42.5 2 0.6 162 000 226 000 2 900 3 900 HR 55 KBE 1003+L 67 96 2 0.6 0.40 2.5 1.7 1.6 1.63
100 60 48.5 2 0.6 188 000 274 000 2 900 3 900 HR 55 KBE 52X+L 67 97 2 0.6 0.40 2.5 1.7 1.6 1.88
120 70 57 2.5 0.6 256 000 342 000 2 500 3 400 HR 55 KBE 43+L 70 113 2 0.6 0.35 2.9 2.0 1.9 3.52
60 110 53 43.5 2 0.6 178 000 246 000 2 700 3 600 HR 60 KBE 042+L 72 105 2 0.6 0.40 2.5 1.7 1.6 2.03
110 66 54.5 2 0.6 225 000 335 000 2 700 3 600 HR 60 KBE 52X+L 72 106 2 0.6 0.40 2.5 1.7 1.6 2.52
130 74 59 3 1 298 000 405 000 2 300 3 200 HR 60 KBE 43+L 78 122 2.5 1 0.35 2.9 2.0 1.9 4.40
65 120 56 46.5 2 0.6 210 000 300 000 2 400 3 200 HR 65 KBE 42+L 77 115 2 0.6 0.40 2.5 1.7 1.6 2.58
120 57 47.5 2 0.6 210 000 300 000 2 400 3 200 HR 65 KBE 1202+L 77 115 2 0.6 0.40 2.5 1.7 1.6 2.61
120 73 61.5 2 0.6 269 000 405 000 2 400 3 300 HR 65 KBE 52X+L 77 117 2 0.6 0.40 2.5 1.7 1.6 3.35
140 79 63 3 1 340 000 465 000 2 100 2 900 HR 65 KBE 43+L 83 132 2.5 1 0.35 2.9 2.0 1.9 5.42
70 125 57 46.5 2 0.6 227 000 325 000 2 300 3 100 HR 70 KBE 042+L 82 120 2 0.6 0.42 2.4 1.6 1.6 2.79
125 59 48.5 2 0.6 227 000 325 000 2 300 3 100 HR 70 KBE 42+L 82 120 2 0.6 0.42 2.4 1.6 1.6 2.85
125 74 61.5 2 0.6 270 000 410 000 2 300 3 100 HR 70 KBE 52X+L 82 121 2 0.6 0.42 2.4 1.6 1.6 3.58
150 83 67 3 1 390 000 535 000 2 000 2 700 HR 70 KBE 43+L 88 142 2.5 1 0.35 2.9 2.0 1.9 6.45
75 130 62 51.5 2 0.6 245 000 365 000 2 200 3 000 HR 75 KBE 42+L 87 126 2 0.6 0.44 2.3 1.6 1.5 3.15
130 74 61.5 2 0.6 283 000 440 000 2 200 3 000 HR 75 KBE 52X+L 87 127 2 0.6 0.44 2.3 1.6 1.5 3.73
160 87 69 3 1 435 000 600 000 1 900 2 500 HR 75 KBE 043+L 93 151 2.5 1 0.35 2.9 2.0 1.9 7.66
80 140 61 49 2.5 0.6 269 000 390 000 2 000 2 800 HR 80 KBE 042+L 95 134 2 0.6 0.42 2.4 1.6 1.6 3.70
140 64 51.5 2.5 0.6 269 000 390 000 2 000 2 800 HR 80 KBE 42+L 95 134 2 0.6 0.42 2.4 1.6 1.6 3.70
140 78 63.5 2.5 0.6 330 000 505 000 2 000 2 800 HR 80 KBE 52X+L 95 136 2 0.6 0.42 2.4 1.6 1.6 4.59
170 92 73 3 1 475 000 655 000 1 700 2 400 HR 80 KBE 043+L 98 161 2.5 1 0.35 2.9 2.0 1.9 9.02
85 150 70 57 2.5 0.6 315 000 465 000 1 900 2 600 HR 85 KBE 42+L 100 143 2 0.6 0.42 2.4 1.6 1.6 4.69
150 86 69 2.5 0.6 360 000 555 000 1 900 2 600 HR 85 KBE 52X+L 100 144 2 0.6 0.42 2.4 1.6 1.6 5.70
180 98 77 4 1 530 000 745 000 1 600 2 200 HR 85 KBE 043+L 106 169 3 1 0.35 2.9 2.0 1.9 10.8
90 160 71 58 2.5 0.6 345 000 510 000 1 800 2 400 HR 90 KBE 042+L 105 152 2 0.6 0.42 2.4 1.6 1.6 5.53
160 74 61 2.5 0.6 345 000 510 000 1 800 2 400 HR 90 KBE 42+L 105 152 2 0.6 0.42 2.4 1.6 1.6 5.71
160 94 77 2.5 0.6 440 000 700 000 1 800 2 400 HR 90 KBE 52X+L 105 154 2 0.6 0.42 2.4 1.6 1.6 7.26
Remarks For other double-row tapered roller bearings not listed above, please contact NSK.
B 172 B 173
B110-181E.indd 172-173 11/20/13 4:57:20 PM

B2
C
r1 rb

ra
P = X Fr +Y Fa

X Y X Y
1 Y3 0.67 Y2
P0 =Fr +Y0 Fa
90 190 102 81 4 1 595 000 845 000 1 600 2 100 HR 90 KBE 043+L 111 178 3 1 0.35 2.9 2.0 1.9 12.7
190 144 115 4 1 770 000 1 180 000 1 600 2 200 HR 90 KBE 1901+L 111 179 3 1 0.35 2.9 2.0 1.9 17.9
95 170 78 63 3 1 385 000 570 000 1 700 2 300 HR 95 KBE 42+L 113 161 2.5 1 0.42 2.4 1.6 1.6 6.75
170 100 83 3 1 495 000 800 000 1 700 2 300 HR 95 KBE 52+L 113 163 2.5 1 0.42 2.4 1.6 1.6 8.60
200 108 85 4 1 640 000 910 000 1 500 2 000 HR 95 KBE 43+L 116 187 3 1 0.35 2.9 2.0 1.9 14.7
100 165 52 46 2.5 0.6 222 000 340 000 1 700 2 300 100 KBE 31+L 115 156 2 0.6 0.33 3.0 2.0 2.0 4.04
180 81 64 3 1 435 000 665 000 1 600 2 200 HR100 KBE 1805+L 118 170 2.5 1 0.42 2.4 1.6 1.6 8.16
180 81 65 3 1 435 000 665 000 1 600 2 200 HR100 KBE 042+L 118 170 2.5 1 0.42 2.4 1.6 1.6 8.13
180 82 66 3 1 435 000 665 000 1 600 2 200 HR100 KBE 1801+L 118 170 2.5 1 0.42 2.4 1.6 1.6 8.22
180 83 67 3 1 435 000 665 000 1 600 2 200 HR100 KBE 42+L 118 170 2.5 1 0.42 2.4 1.6 1.6 8.7
180 105 85 3 1 555 000 905 000 1 600 2 200 HR100 KBE 1802+L 118 173 2.5 1 0.42 2.4 1.6 1.6 10.6
180 107 87 3 1 555 000 905 000 1 600 2 200 HR100 KBE 52X+L 118 173 2.5 1 0.42 2.4 1.6 1.6 10.7
180 110 90 3 1 555 000 905 000 1 600 2 200 HR100 KBE 1804+L 118 173 2.5 1 0.42 2.4 1.6 1.6 11
215 112 87 4 1 725 000 1 050 000 1 400 1 900 HR100 KBE 043+L 121 200 3 1 0.35 2.9 2.0 1.9 18.1
105 190 88 70 3 1 480 000 735 000 1 500 2 000 HR105 KBE 42X+L 123 179 2.5 1 0.42 2.4 1.6 1.6 9.76
190 117 96 3 1 620 000 1 020 000 1 500 2 000 HR105 KBE 1902+L 123 182 2.5 1 0.42 2.4 1.6 1.6 13.4
190 115 95 3 1 620 000 1 020 000 1 500 2 000 HR105 KBE 52+L 123 182 2.5 1 0.42 2.4 1.6 1.6 13.1
225 116 91 4 1 780 000 1 130 000 1 300 1 800 HR105 KBE 043+L 126 209 3 1 0.35 2.9 2.0 1.9 20.4
110 180 56 50 2.5 0.6 264 000 400 000 1 500 2 000 110 KBE 31+L 125 172 2 0.6 0.39 2.6 1.7 1.7 5.11
180 70 56 2.5 0.6 340 000 555 000 1 500 2 000 110 KBE 031+L 125 172 2 0.6 0.39 2.6 1.7 1.7 6.33
180 125 100 2.5 0.6 550 000 1 060 000 1 500 2 100 110 KBE 1802+L 125 172 2 0.6 0.26 3.8 2.6 2.5 11.4
200 90 72 3 1 540 000 840 000 1 400 1 900 HR110 KBE 42+L 128 190 2.5 1 0.42 2.4 1.6 1.6 11.2
200 92 74 3 1 540 000 840 000 1 400 1 900 HR110 KBE 42X+L 128 190 2.5 1 0.42 2.4 1.6 1.6 11.5
200 120 100 3 1 685 000 1 130 000 1 400 1 900 HR110 KBE 2001+L 128 193 2.5 1 0.42 2.4 1.6 1.6 15.4
200 121 101 3 1 685 000 1 130 000 1 400 1 900 HR110 KBE 52X+L 128 193 2.5 1 0.42 2.4 1.6 1.6 15.2
240 118 93 4 1.5 830 000 1 190 000 1 200 1 700 HR110 KBE 043+L 131 223 3 1.5 0.35 2.9 2.0 1.9 23.6
120 180 46 41 2.5 0.6 184 000 296 000 1 500 2 000 120 KBE 30+L 135 172 2 0.6 0.40 2.5 1.7 1.6 3.75
180 58 46 2.5 0.6 260 000 450 000 1 500 2 000 120 KBE 030+L 135 172 2 0.6 0.39 2.6 1.7 1.7 4.64
200 62 55 2.5 0.6 310 000 500 000 1 400 1 800 120 KBE 31+L 135 190 2 0.6 0.39 2.6 1.7 1.7 7.35
200 78 62 2.5 0.6 415 000 690 000 1 400 1 900 120 KBE 031+L 135 190 2 0.6 0.39 2.6 1.7 1.7 8.97
200 100 84 2.5 0.6 515 000 885 000 1 400 1 800 120 KBE 2001+L 135 193 2 0.6 0.37 2.7 1.8 1.8 11.3
215 97 78 3 1 575 000 900 000 1 300 1 800 HR120 KBE 42X+L 138 204 2.5 1 0.44 2.3 1.6 1.5 13.7
215 132 109 3 1 750 000 1 270 000 1 300 1 800 HR120 KBE 52X+L 138 207 2.5 1 0.44 2.3 1.6 1.5 18.8
260 128 101 4 1 915 000 1 310 000 1 100 1 500 HR120 KBE 43+L 141 240 3 1 0.35 2.9 2.0 1.9 29.4
260 188 145 4 1 1 320 000 2 110 000 1 100 1 500 HR120 KBE 2601+L 141 242 3 1 0.35 2.9 2.0 1.9 44.6
B 174 B 175
B110-181E.indd 174-175 11/20/13 4:57:21 PM

B2
C
r1 rb

ra
P = X Fr +Y Fa

X Y X Y
1 Y3 0.67 Y2
P0 =Fr +Y0 Fa
125 210 110 88 4 1 560 000 1 030 000 1 300 1 800 125 KBE 2101+L 146 201 3 1 0.43 2.3 1.6 1.5 14.5
130 230 98 78.5 4 1 640 000 1 010 000 1 200 1 600 HR130 KBE 42+L 151 220 3 1 0.44 2.3 1.6 1.5 15.8
230 100 80.5 4 1 640 000 1 010 000 1 200 1 600 HR130 KBE 2301+L 151 220 3 1 0.44 2.3 1.6 1.5 15.9
280 137 107.5 5 1.5 940 000 1 350 000 1 000 1 400 130 KBE 43+L 157 258 4 1.5 0.36 2.8 1.9 1.8 35
230 145 115 4 1 905 000 1 580 000 1 200 1 700 HR130 KBE 2302+L 151 221 3 1 0.44 2.3 1.6 1.5 24.1
230 145 117.5 4 1 905 000 1 580 000 1 200 1 700 HR130 KBE 52+L 151 222 3 1 0.44 2.3 1.6 1.5 23.8
230 150 120 4 1 905 000 1 580 000 1 200 1 700 HR130 KBE 2303+L 151 221 3 1 0.44 2.3 1.6 1.5 24.2
140 210 53 47 2.5 0.6 280 000 495 000 1 200 1 700 140 KBE 30+L 155 202 2 0.6 0.39 2.6 1.7 1.7 6.02
210 66 53 2.5 1 305 000 530 000 1 200 1 700 140 KBE 030+L 155 202 2 1 0.40 2.5 1.7 1.6 7.02
210 106 94 2.5 0.6 555 000 1 200 000 1 300 1 700 140 KBE 2101+L 155 202 2 0.6 0.33 3.0 2.0 2.0 12.3
225 68 61 3 1 400 000 630 000 1 200 1 600 140 KBE 31+L 158 216 2.5 1 0.39 2.6 1.7 1.7 9.31
225 84 68 3 1 490 000 850 000 1 200 1 600 140 KBE 031+L 158 215 2.5 1 0.39 2.6 1.7 1.7 11.6
225 85 68 3 1 490 000 850 000 1 200 1 600 140 KBE 2201+L 158 215 2.5 1 0.39 2.6 1.7 1.7 11.7
230 120 94 3 1 685 000 1 270 000 1 200 1 600 140 KBE 2301+L 158 220 2.5 1 0.33 3.0 2.0 2.0 17.6
230 140 110 3 1 820 000 1 550 000 1 200 1 600 140 KBE 2302+L 158 221 2.5 1 0.35 2.9 2.0 1.9 20.7
240 132 106 4 1.5 685 000 1 360 000 1 100 1 500 140 KBE 2401+L 161 227 3 1.5 0.44 2.3 1.5 1.5 22.7
250 102 82.5 4 1 670 000 1 030 000 1 100 1 500 HR140 KBE 42+L 161 237 3 1 0.44 2.3 1.6 1.5 18.9
250 153 125.5 4 1 1 040 000 1 830 000 1 100 1 500 HR140 KBE 52X+L 161 241 3 1 0.44 2.3 1.6 1.5 29.6
300 145 115.5 5 1.5 1 030 000 1 480 000 1 000 1 300 140 KBE 43+L 167 275 4 1.5 0.36 2.8 1.9 1.8 42.6
150 225 56 50 3 1 300 000 545 000 1 200 1 600 150 KBE 30+L 168 213 2.5 1 0.35 2.9 2.0 1.9 7.41
225 70 56 3 1 395 000 685 000 1 200 1 600 150 KBE 030+L 168 215 2.5 1 0.35 2.9 2.0 1.9 8.70
250 80 71 3 1 510 000 810 000 1 100 1 400 150 KBE 31+L 168 240 2.5 1 0.40 2.5 1.7 1.6 14.2
250 100 80 3 1 630 000 1 090 000 1 100 1 400 150 KBE 031+L 168 238 2.5 1 0.39 2.6 1.7 1.7 17.8
250 115 95 3 1 745 000 1 320 000 1 100 1 500 150 KBE 2502+L 168 238 2.5 1 0.37 2.7 1.8 1.8 20.9
260 150 115 4 1 815 000 1 520 000 1 100 1 400 150 KBE 2601+L 171 242 3 1 0.43 2.3 1.6 1.5 30.0
270 109 87 4 1 830 000 1 330 000 1 000 1 400 HR150 KBE 42+L 171 253 3 1 0.44 2.3 1.6 1.5 24.3
270 164 130 4 1 1 210 000 2 150 000 1 000 1 400 HR150 KBE 52X+L 171 257 3 1 0.44 2.3 1.6 1.5 37.3
270 174 140 4 1 1 210 000 2 150 000 1 000 1 400 HR150 KBE 2701+L 171 257 3 1 0.44 2.3 1.6 1.5 39.7
320 154 120 5 1.5 1 420 000 2 130 000 900 1 200 HR150 KBE 43+L 177 295 4 1.5 0.35 2.9 2.0 1.9 53.4
B 176 B 177
B110-181E.indd 176-177 11/20/13 4:57:22 PM

B2
C
r1 rb

ra
P = X Fr +Y Fa

X Y X Y
1 Y3 0.67 Y2
P0 =Fr +Y0 Fa
160 240 60 53 3 1 355 000 580 000 1 100 1 500 160 KBE 30+L 178 231 2.5 1 0.37 2.7 1.8 1.8 8.56
240 75 60 3 1 395 000 710 000 1 100 1 500 160 KBE 030+L 178 230 2.5 1 0.40 2.5 1.7 1.6 10.5
240 110 90 3 1 650 000 1 290 000 1 100 1 500 160 KBE 2401+L 178 232 2.5 1 0.38 2.6 1.8 1.7 16.2
270 86 76 3 1 540 000 885 000 1 000 1 300 160 KBE 31+L 178 255 2.5 1 0.40 2.5 1.7 1.6 18.6
270 108 86 3 1 775 000 1 380 000 1 000 1 300 160 KBE 031+L 178 256 2.5 1 0.39 2.6 1.7 1.7 23.1
270 140 120 3 1 990 000 1 880 000 1 000 1 300 160 KBE 2701+L 178 261 2.5 1 0.39 2.6 1.7 1.7 30.6
280 150 125 4 1 1 100 000 2 020 000 1 000 1 300 160 KBE 2801+L 181 266 3 1 0.32 3.2 2.1 2.1 35.9
290 115 91 4 1 800 000 1 220 000 900 1 300 160 KBE 42+L 181 275 3 1 0.43 2.3 1.6 1.5 28.2
290 178 144 4 1 1 360 000 2 440 000 1 000 1 300 HR160 KBE 52X+L 181 277 3 1 0.44 2.3 1.6 1.5 47.3
340 160 126 5 1.5 1 310 000 1 920 000 800 1 100 160 KBE 43+L 187 314 4 1.5 0.36 2.8 1.9 1.8 60.4
165 290 150 125 4 1 1 140 000 2 130 000 900 1 300 165 KBE 2901+L 186 272 3 1 0.33 3.1 2.1 2.0 39.5
170 250 85 65 3 1 435 000 845 000 1 000 1 400 170 KBE 2501+L 188 241 2.5 1 0.44 2.3 1.5 1.5 12.3
260 67 60 3 1 400 000 700 000 1 000 1 300 170 KBE 30+L 188 248 2.5 1 0.40 2.5 1.7 1.6 11.8
260 84 67 3 1 575 000 1 030 000 1 000 1 300 170 KBE 030+L 188 249 2.5 1 0.39 2.6 1.7 1.7 14.4
280 88 78 3 1 630 000 1 040 000 900 1 300 170 KBE 31+L 188 266 2.5 1 0.39 2.6 1.7 1.7 19.7
280 110 88 3 1 820 000 1 450 000 900 1 300 170 KBE 031+L 188 268 2.5 1 0.39 2.6 1.7 1.7 24.2
280 150 130 3 1 1 110 000 2 160 000 1 000 1 300 170 KBE 2802+L 188 269 2.5 1 0.39 2.6 1.7 1.7 34.6
310 192 152 5 1.5 1 590 000 2 910 000 900 1 200 HR170 KBE 52X+L 197 297 4 1.5 0.44 2.3 1.6 1.5 57.3
180 280 74 66 3 1 455 000 810 000 900 1 300 180 KBE 30+L 198 265 2.5 1 0.40 2.5 1.7 1.6 15.4
280 93 74 3 1 655 000 1 220 000 900 1 200 180 KBE 030+L 198 265 2.5 1 0.35 2.9 2.0 1.9 14.4
300 96 85 4 1.5 725 000 1 210 000 900 1 200 180 KBE 31+L 201 284 3 1.5 0.39 2.6 1.7 1.7 24.8
300 120 96 4 1.5 940 000 1 690 000 900 1 200 180 KBE 031+L 201 287 3 1.5 0.39 2.6 1.7 1.7 31.1
320 127 99 5 1.5 895 000 1 390 000 800 1 200 180 KBE 42+L 207 300 4 1.5 0.44 2.3 1.5 1.5 36.5
320 192 152 5 1.5 1 640 000 3 050 000 900 1 200 HR180 KBE 52X+L 207 308 4 1.5 0.45 2.2 1.5 1.5 59.2
340 180 140 5 1.5 1 410 000 2 510 000 800 1 100 180 KBE 3401+L 207 305 4 1.5 0.43 2.3 1.6 1.5 68.1
190 290 75 67 3 1 490 000 845 000 900 1 200 190 KBE 30+L 208 279 2.5 1 0.39 2.6 1.7 1.7 16.2
290 94 75 3 1 670 000 1 230 000 900 1 200 190 KBE 030+L 208 279 2.5 1 0.40 2.5 1.7 1.6 20.1
320 104 92 4 1.5 800 000 1 380 000 800 1 100 190 KBE 31+L 211 301 3 1.5 0.40 2.5 1.7 1.6 30.9
320 130 104 4 1.5 1 070 000 1 960 000 800 1 100 190 KBE 031+L 211 302 3 1.5 0.39 2.6 1.7 1.7 39.0
340 133 105 5 1.5 990 000 1 580 000 800 1 100 190 KBE 42+L 217 320 4 1.5 0.40 2.5 1.7 1.6 43.9
340 204 160 5 1.5 1 910 000 3 550 000 800 1 100 HR190 KBE 52X+L 217 327 4 1.5 0.44 2.3 1.6 1.5 70.8
200 310 152 123 3 1 1 300 000 2 740 000 800 1 100 HR200 KBE 3101+L 218 301 2.5 1 0.43 2.3 1.6 1.5 40.1
320 146 110 5 1.5 990 000 2 120 000 800 1 100 200 KBE 3201+L 227 301 4 1.5 0.52 1.9 1.3 1.3 41.6
330 180 140 5 1.5 1 390 000 2 730 000 800 1 100 200 KBE 3301+L 227 316 4 1.5 0.42 2.4 1.6 1.6 54.4
340 112 100 4 1.5 940 000 1 670 000 800 1 000 200 KBE 31+L 221 321 3 1.5 0.40 2.5 1.7 1.6 38.8
340 140 112 4 1.5 1 260 000 2 250 000 800 1 000 200 KBE 031+L 221 324 3 1.5 0.39 2.6 1.7 1.7 47.0
360 142 110 5 1.5 1 100 000 1 780 000 700 1 000 200 KBE 42+L 227 338 4 1.5 0.40 2.5 1.7 1.6 52.6
360 218 174 5 1.5 2 070 000 3 850 000 800 1 000 HR200 KBE 52+L 227 344 4 1.5 0.41 2.5 1.7 1.6 88.3
B 178 B 179
B110-181E.indd 178-179 11/20/13 4:57:23 PM

B2
C
r1 rb

ra
P = X Fr +Y Fa

X Y X Y
1 Y3 0.67 Y2
P0 =Fr +Y0 Fa
206 283 102 83 4 1.5 580 000 1 430 000 900 1 200 206 KBE 2801+L 227 275 3 1.5 0.51 2.0 1.3 1.3 18.1
210 355 116 103 4 1.5 905 000 1 520 000 700 1 000 210 KBE 31+L 231 338 3 1.5 0.46 2.2 1.5 1.4 41.7
220 300 110 88 3 1 730 000 1 710 000 800 1 100 220 KBE 3001+L 238 292 2.5 1 0.37 2.7 1.8 1.8 21.2
340 90 80 4 1.5 695 000 1 280 000 700 1 000 220 KBE 30+L 241 324 3 1.5 0.40 2.5 1.7 1.6 27.9
340 113 90 4 1.5 920 000 1 830 000 700 1 000 220 KBE 030+L 241 327 3 1.5 0.40 2.5 1.7 1.6 34.7
370 120 107 5 1.5 1 110 000 1 940 000 700 1 000 220 KBE 31+L 247 345 4 1.5 0.39 2.6 1.7 1.7 48.3
370 150 120 5 1.5 1 460 000 2 760 000 700 1 000 220 KBE 031+L 247 349 4 1.5 0.39 2.6 1.7 1.7 60.2
400 158 122 5 1.5 1 390 000 2 300 000 600 900 220 KBE 42+L 247 371 4 1.5 0.40 2.5 1.7 1.6 74.2
240 360 92 82 4 1.5 780 000 1 490 000 700 900 240 KBE 30+L 261 344 3 1.5 0.39 2.6 1.7 1.7 30.1
360 115 92 4 1.5 1 020 000 2 040 000 700 900 240 KBE 030+L 261 344 3 1.5 0.35 2.9 2.0 1.9 37.3
400 128 114 5 1.5 1 180 000 2 190 000 600 900 240 KBE 31+L 267 380 4 1.5 0.43 2.3 1.6 1.5 60.0
400 160 128 5 1.5 1 620 000 3 050 000 600 900 240 KBE 031+L 267 378 4 1.5 0.39 2.6 1.7 1.7 73.6
400 209 168 5 1.5 2 220 000 4 450 000 600 900 240 KBE 4003+L 267 384 4 1.5 0.33 3.0 2.0 2.0 96.4
250 380 98 87 4 1 795 000 1 460 000 600 900 250 KBE 3801+L 271 365 3 1 0.40 2.5 1.7 1.6 35.5
260 400 104 92 5 1.5 895 000 1 670 000 600 800 260 KBE 30+L 287 379 4 1.5 0.40 2.5 1.7 1.6 43.4
400 130 104 5 1.5 1 210 000 2 460 000 600 800 260 KBE 030+L 287 382 4 1.5 0.40 2.5 1.7 1.6 54.1
440 144 128 5 1.5 1 540 000 2 760 000 600 800 260 KBE 31+L 287 416 4 1.5 0.39 2.6 1.7 1.7 82.5
440 172 145 5 1.5 1 870 000 3 500 000 600 800 260 KBE 4401+L 287 414 4 1.5 0.38 2.6 1.8 1.7 98.1
440 180 144 5 1.5 2 110 000 4 150 000 600 800 260 KBE 031+L 287 416 4 1.5 0.39 2.6 1.7 1.7 104.0
B 180 B 181
B110-181E.indd 180-181 11/20/13 4:57:24 PM

SPHERICAL ROLLER BEARINGS
Shown in the figures, types EA, C, CD, CA, which are designed for high load capacity, are
SPHERICAL ROLLER BEARINGS available. Types EA, C and CD have pressed steel cages, and type CA has machined brass
cages. The EA type bearings listed here are classified as NSKHPS bearings, which offer
Cylindrical Bores, Tapered Bores Bore Diameter 20 150mm B184 particularly high load-carrying capacity, high limiting speeds, and are highly functional
under high-temperature operating conditions of up to 200C.
An oil groove and holes are provided in the outer ring to supply lubricant and the bearing
Bore Diameter 600 1400mm B202 numbers are suffixed with E4.
To use bearings with oil grooves and holes, it is recommended to provide an oil groove
EA in the housing bore, since the depth of the groove in the bearing is limited. The number
and dimensions of the oil groove and holes are shown in Tables 1 and 2.
When bearings with a hole for a locking pin to prevent outer ring rotation are required,
please inform NSK.
C and CD
TOLERANCES AND RUNNING ACCURACY Table 8.2 (Pages A60 to A63)
RECOMMENDED FITS Table 9.2 (Page A84)
INTERNAL CLEARANCE Table 9.15 (Page A92)
CA
B The permissible misalignment of spherical roller bearings varies depending on the size
W and load, but it is approximately 0.018 to 0.045 radian (1 to 2.5) with normal loads.
dOH
LIMITING SPEEDS
The limiting speeds listed in the bearing tables should be adjusted depending on the
bearing load conditions. Also, higher speeds are attainable by making changes in the
lubrication method, cage design, etc. Refer to Page A37 for detailed information.
And if the load on spherical roller bearings

Table 1 Dimensions of Oil Grooves Table 2 Number of Oil Holes
becomes too small during operation or if
and Holes Units : mm the ratio of axial and radial loads is larger
Nominal Width B Oil Groove Hole Diameter Nominal Outer Ring Dia D
Number
than the value of e(listed in the bearing
over incl. Width W dOH (mm) tables), slippage occurs between the rollers
of Holes
18 30 5 2.5 over incl. and raceways, which may result in smearing.
30 40 6 3 180 4 The higher the weight of the rollers and cage,
40 50 7 4 180 250 6 the higher this tendency becomes, especially
50 65 8 5 250 315 6 for large spherical roller bearings.
65 80 10 6 315 400 6 If very small bearing loads are expected,
80 100 12 8 400 500 6 please contact NSK for selection of an
100 120 15 10 500 630 8 appropriate bearing.
120 160 20 12
160 200 25 15 630 800 8
800 1000 8
200 250 30 20 1000 1250 8
250 315 35 20
315 400 40 25 1250 1600 8
400 40 25 1600 2000 8
B 182 B 183
B182-205E.indd 182-183 11/20/13 4:57:47 PM

B B
r r ra
r ra
jD a P =X Fr +Y Fa
jD jd jD jd jd a
Fa/ Fre Fa/ Fr>e
X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa
Cylindrical Bore Tapered Bore Without an Oil Groove or Holes given in the table below.
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers Abutment and Fillet Dimensions Constant Axial Load Mass
(mm) (N) {kgf} (min1) (mm) Factors (kg)
d D B r Cr C 0r Cr C 0r Grease Oil Cylindrical Bore Tapered Bore( 1) da Da ra e Y2 Y3 Y0

min. min. max. max. min. max. approx.
20 52 15 1.1 29 300 26 900 2 980 2 740 6 300 8 200 21304CDE4 21304CDKE4 27 28 45 42 1 0.31 3.2 2.1 2.1 0.17
25 52 18 1 37 500 37 000 3 850 3 800 7 100 9 000 22205CE4 22205CKE4 31 31 46 45 1 0.35 2.9 1.9 1.9 0.17
62 17 1.1 43 000 40 500 4 350 4 150 5 300 6 700 21305CDE4 21305CDKE4 32 34 55 51 1 0.29 3.4 2.3 2.3 0.26
30 62 20 1 50 000 50 000 5 100 5 100 6 000 7 500 22206CE4 22206CKE4 36 37 56 54 1 0.33 3.1 2.1 2.0 0.27
72 19 1.1 55 000 54 000 5 600 5 500 4 500 6 000 21306CDE4 21306CDKE4 37 40 65 59 1 0.28 3.6 2.4 2.3 0.39
35 72 23 1.1 69 000 71 000 7 050 7 200 5 300 6 700 22207CE4 22207CKE4 42 43 65 63 1 0.32 3.1 2.1 2.0 0.42
80 21 1.5 71 500 76 000 7 250 7 750 4 000 5 300 21307CDE4 21307CDKE4 44 47 71 67 1.5 0.28 3.6 2.4 2.4 0.53
40 80 23 1.1 113 000 99 500 11 500 10 100 6 700 8 500 *22208EAE4 *22208EAKE4 47 49 73 70 1 0.28 3.6 2.4 2.4 0.50
90 23 1.5 118 000 111 000 12 000 11 300 6 000 7 500 *21308EAE4 *21308EAKE4 49 54 81 75 1.5 0.25 3.9 2.7 2.6 0.73
90 33 1.5 170 000 153 000 17 300 15 600 5 300 6 700 *22308EAE4 *22308EAKE4 49 52 81 77 1.5 0.35 2.8 1.9 1.9 0.98
45 85 23 1.1 118 000 111 000 12 000 11 300 6 000 7 500 *22209EAE4 *22209EAKE4 52 54 78 75 1 0.25 3.9 2.7 2.6 0.55
100 25 1.5 149 000 144 000 15 200 14 600 5 000 6 300 *21309EAE4 *21309EAKE4 54 65 91 89 1.5 0.23 4.3 2.9 2.8 0.96
100 36 1.5 207 000 195 000 21 100 19 900 4 500 5 600 *22309EAE4 *22309EAKE4 54 59 91 86 1.5 0.34 2.9 2.0 1.9 1.34
50 90 23 1.1 124 000 119 000 12 600 12 100 5 600 7 100 *22210EAE4 *22210EAKE4 57 60 83 81 1 0.24 4.3 2.9 2.8 0.61
110 27 2 178 000 174 000 18 100 17 800 4 500 5 600 *21310EAE4 *21310EAKE4 60 72 100 98 2 0.23 4.4 3.0 2.9 1.21
110 40 2 246 000 234 000 25 100 23 900 4 300 5 300 *22310EAE4 *22310EAKE4 60 64 100 93 2 0.35 2.8 1.9 1.9 1.78
55 100 25 1.5 149 000 144 000 15 200 14 600 5 300 6 700 *22211EAE4 *22211EAKE4 64 65 91 89 1.5 0.23 4.3 2.9 2.8 0.81
120 29 2 178 000 174 000 18 100 17 800 4 500 5 600 *21311EAE4 *21311EAKE4 65 72 110 98 2 0.23 4.4 3.0 2.9 1.58
120 43 2 292 000 292 000 29 800 29 800 3 800 4 800 *22311EAE4 *22311EAKE4 65 73 110 103 2 0.34 2.9 2.0 1.9 2.3
Note (1) The suffix K represents bearings with tapered bores (taper 1 : 12). Remarks 1. The bearings denoted by an asterisk (*) are NSKHPS bearings and an oil groove and holes are standard for them.
2. When making a selection of the recommended fit (Tolerance of Shaft) on Page A84 of the NSK Rolling Bearings
catalog, in case of NSKHPS bearings, the conditions are different.
The segmentations are: Light Loads (0.05Cr); Normal Loads (0.05 to 0.10Cr); and Heavy Loads (>0.10Cr).
3. For the dimensions of adapters and withdrawal sleeves, refer to Pages B358 B359, and B366.
B 184 B 185
B182-205E.indd 184-185 11/20/13 4:57:49 PM

B B
r r ra
r ra
jD a P =X Fr +Y Fa
jD jd jD jd jd a
Fa/ Fre Fa/ Fr>e
X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa

60 95 26 1.1 98 500 141 000 10 000 14 400 3 600 4 500 23012CE4 23012CKE4 67 68 88 85 1 0.26 3.9 2.6 2.5 0.68
110 28 1.5 178 000 174 000 18 100 17 800 4 800 6 000 *22212EAE4 *22212EAKE4 69 72 101 98 1.5 0.23 4.4 3.0 2.9 1.1
130 31 2.1 238 000 244 000 24 200 24 900 3 800 4 800 *21312EAE4 *21312EAKE4 72 87 118 117 2 0.22 4.5 3.0 3.0 1.98
130 46 2.1 340 000 340 000 34 500 35 000 3 600 4 500 *22312EAE4 *22312EAKE4 72 79 118 111 2 0.34 3.0 2.0 1.9 2.89
65 120 31 1.5 221 000 230 000 22 500 23 500 4 300 5 300 *22213EAE4 *22213EAKE4 74 80 111 107 1.5 0.24 4.2 2.8 2.7 1.51
140 33 2.1 264 000 275 000 27 000 28 000 3 600 4 500 *21313EAE4 *21313EAKE4 77 94 128 126 2 0.22 4.6 3.1 3.0 2.45
140 48 2.1 375 000 380 000 38 000 38 500 3 200 4 000 *22313EAE4 *22313EAKE4 77 84 128 119 2 0.33 3.0 2.0 2.0 3.52
70 125 31 1.5 225 000 232 000 22 900 23 600 4 000 5 300 *22214EAE4 *22214EAKE4 79 84 116 111 1.5 0.23 4.3 2.9 2.8 1.58
150 35 2.1 310 000 325 000 32 000 33 500 3 200 4 000 *21314EAE4 *21314EAKE4 82 101 138 135 2 0.22 4.6 3.1 3.0 3.0
150 51 2.1 425 000 435 000 43 500 44 000 3 000 3 800 *22314EAE4 *22314EAKE4 82 91 138 129 2 0.33 3.0 2.0 2.0 4.28
75 130 31 1.5 238 000 244 000 24 200 24 900 4 000 5 000 *22215EAE4 *22215EAKE4 84 87 121 117 1.5 0.22 4.5 3.0 3.0 1.64
160 37 2.1 310 000 325 000 32 000 33 500 3 200 4 000 *21315EAE4 *21315EAKE4 87 101 148 134 2 0.22 4.6 3.1 3.0 3.64
160 55 2.1 485 000 505 000 49 500 51 500 2 800 3 600 *22315EAE4 *22315EAKE4 87 97 148 137 2 0.33 3.0 2.0 2.0 5.26
80 140 33 2 264 000 275 000 27 000 28 000 3 600 4 500 *22216EAE4 *22216EAKE4 90 94 130 126 2 0.22 4.6 3.1 3.0 2.01
170 39 2.1 355 000 375 000 36 000 38 000 3 000 3 800 *21316EAE4 *21316EAKE4 92 109 158 146 2 0.23 4.4 3.0 2.9 4.32
170 58 2.1 540 000 565 000 55 000 58 000 2 600 3 400 *22316EAE4 *22316EAKE4 92 103 158 145 2 0.33 3.0 2.0 2.0 6.23
85 150 36 2 310 000 325 000 32 000 33 500 3 400 4 300 *22217EAE4 *22217EAKE4 95 101 140 135 2 0.22 4.6 3.1 3.0 2.54
180 41 3 360 000 395 000 37 000 40 000 3 000 4 000 *21317EAE4 *21317EAKE4 99 108 166 142 2.5 0.24 4.3 2.9 2.8 5.2
180 60 3 600 000 630 000 61 000 64 000 2 400 3 200 *22317EAE4 *22317EAKE4 99 110 166 155 2.5 0.33 3.1 2.1 2.0 7.23
Note (1) The suffix K represents bearings with tapered bores (taper 1 : 12). Remarks 1. The bearings denoted by an asterisk (*) are NSKHPS bearings and an oil groove and holes are standard for them.
3. For the dimensions of adapters and withdrawal sleeves, refer to Pages B359 B361, and B366.
B 186 B 187
B182-205E.indd 186-187 11/20/13 4:57:50 PM

B B
r r ra
r ra
jD a P =X Fr +Y Fa
jD jd jD jd jd a
Fa/ Fre Fa/ Fr>e
X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa

90 160 40 2 360 000 395 000 37 000 40 000 3 200 4 000 *22218EAE4 *22218EAKE4 100 108 150 142 2 0.24 4.3 2.9 2.8 3.3
160 52.4 2 340 000 490 000 34 500 50 000 1 800 2 400 23218CE4 23218CKE4 100 105 150 138 2 0.32 3.2 2.1 2.1 4.51
190 43 3 415 000 450 000 42 000 46 000 2 800 3 600 *21318EAE4 *21318EAKE4 104 115 176 152 2.5 0.24 4.3 2.9 2.8 6.1
190 64 3 665 000 705 000 68 000 72 000 2 400 3 000 *22318EAE4 *22318EAKE4 104 115 176 163 2.5 0.33 3.1 2.1 2.0 8.56
95 170 43 2.1 415 000 450 000 42 000 46 000 3 000 3 800 *22219EAE4 *22219EAKE4 107 115 158 152 2 0.24 4.3 2.9 2.8 4.04
170 55.6 2.1 370 000 525 000 37 500 53 500 1 700 2 200 23219CAE4 23219CAKE4 107 158 146 2 0.32 3.1 2.1 2.0 5.33
200 45 3 345 000 435 000 35 000 44 500 1 500 2 000 21319CE4 21319CKE4 109 127 186 172 2.5 0.22 4.6 3.1 3.0 6.92
200 67 3 735 000 780 000 75 000 79 500 2 200 2 800 *22319EAE4 *22319EAKE4 109 121 186 172 2.5 0.33 3.1 2.1 2.0 9.91
100 150 37 1.5 212 000 335 000 21 600 34 500 2 200 2 800 23020CDE4 23020CDKE4 109 112 141 136 1.5 0.22 4.6 3.1 3.0 2.31
150 50 1.5 276 000 470 000 28 100 48 000 1 800 2 400 24020CE4 24020CK30E4 109 110 141 132 1.5 0.30 3.4 2.3 2.2 3.08
165 52 2 345 000 530 000 35 500 54 000 1 700 2 200 23120CE4 23120CKE4 110 113 155 144 2 0.30 3.4 2.3 2.2 4.38
165 65 2 345 000 535 000 35 000 55 000 1 700 2 200 24120CAE4 24120CAK30E4 110 155 143 2 0.35 2.9 1.9 1.9 5.42
180 46 2.1 455 000 490 000 46 500 50 000 2 800 3 600 *22220EAE4 *22220EAKE4 112 119 168 160 2 0.24 4.3 2.9 2.8 4.84
180 60.3 2.1 420 000 605 000 42 500 61 500 1 600 2 200 23220CE4 23220CKE4 112 118 168 155 2 0.32 3.2 2.1 2.1 6.6
215 47 3 395 000 485 000 40 500 49 500 1 400 1 900 21320CE4 21320CKE4 114 133 201 184 2.5 0.21 4.7 3.2 3.1 8.46
215 73 3 860 000 930 000 88 000 94 500 2 000 2 600 *22320EAE4 *22320EAKE4 114 130 201 184 2.5 0.33 3.0 2.0 2.0 12.7
110 170 45 2 293 000 465 000 29 900 47 500 2 000 2 400 23022CDE4 23022CDKE4 120 124 160 153 2 0.24 4.2 2.8 2.8 3.76
170 60 2 380 000 645 000 38 500 66 000 1 600 2 200 24022CE4 24022CK30E4 120 121 160 148 2 0.32 3.1 2.1 2.1 4.96
180 56 2 385 000 630 000 39 500 64 000 1 600 2 000 23122CE4 23122CKE4 120 127 170 158 2 0.28 3.5 2.4 2.3 5.7
180 69 2 460 000 750 000 47 000 76 500 1 600 2 000 24122CE4 24122CK30E4 120 123 170 154 2 0.36 2.8 1.9 1.8 6.84
200 53 2.1 605 000 645 000 61 500 66 000 2 600 3 200 *22222EAE4 *22222EAKE4 122 129 188 178 2 0.25 4.0 2.7 2.6 6.99
200 69.8 2.1 515 000 760 000 52 500 77 500 1 500 1 900 23222CE4 23222CKE4 122 130 188 170 2 0.34 3.0 2.0 1.9 9.54
240 50 3 450 000 545 000 46 000 55 500 1 300 1 700 21322CAE4 21322CAKE4 124 226 206 2.5 0.22 4.6 3.1 3.0 11.2
240 80 3 1030 000 1 120 000 105 000 115 000 1 900 2 400 *22322EAE4 *22322EAKE4 124 145 226 206 2.5 0.33 3.1 2.1 2.0 17.6
Note (1) The suffix K or K30 represents bearings with tapered bores (taper 1 : 12 or 1 : 30). Remarks 1. The bearings denoted by an asterisk (*) are NSKHPS bearings and an oil groove and holes are standard for them.
3. For the dimensions of adapters and withdrawal sleeves, refer to Pages B360 B361, and B366 B367.
B 188 B 189
B182-205E.indd 188-189 11/20/13 4:57:51 PM

B B
r r ra
r ra
jD a P =X Fr +Y Fa
jD jd jD jd jd a
Fa/ Fre Fa/ Fr>e
X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa

120 180 46 2 315 000 525 000 32 000 53 500 1 800 2 200 23024CDE4 23024CDKE4 130 134 170 163 2 0.22 4.5 3.0 2.9 4.11
180 60 2 395 000 705 000 40 500 72 000 1 500 2 000 24024CE4 24024CK30E4 130 131 170 158 2 0.32 3.2 2.1 2.1 5.33
200 62 2 465 000 720 000 47 500 73 500 1 400 1 800 23124CE4 23124CKE4 130 138 190 175 2 0.29 3.5 2.4 2.3 7.85
200 80 2 575 000 950 000 58 500 96 500 1 400 1 800 24124CE4 24124CK30E4 130 136 190 171 2 0.37 2.7 1.8 1.8 10
215 58 2.1 685 000 765 000 70 000 78 000 2 400 3 000 *22224EAE4 *22224EAKE4 132 142 203 190 2 0.25 3.9 2.7 2.6 8.8
215 76 2.1 630 000 970 000 64 500 99 000 1 300 1 700 23224CE4 23224CKE4 132 140 203 182 2 0.34 2.9 2.0 1.9 12.1
260 86 3 1190 000 1 320 000 122 000 134 000 1 700 2 200 *22324EAE4 *22324EAKE4 134 157 246 222 2.5 0.32 3.1 2.1 2.0 22.2
130 200 52 2 400 000 655 000 40 500 67 000 1 700 2 000 23026CDE4 23026CDKE4 140 147 190 180 2 0.23 4.3 2.9 2.8 5.98
200 69 2 495 000 865 000 50 500 88 000 1 400 1 800 24026CE4 24026CK30E4 140 143 190 175 2 0.31 3.2 2.2 2.1 7.84
210 64 2 505 000 825 000 51 500 84 500 1 300 1 700 23126CE4 23126CKE4 140 149 200 184 2 0.28 3.6 2.4 2.4 8.69
210 80 2 590 000 1 010 000 60 000 103 000 1 300 1 700 24126CE4 24126CK30E4 140 146 200 180 2 0.35 2.9 1.9 1.9 10.7
230 64 3 820 000 940 000 83 500 96 000 2 200 2 600 *22226EAE4 *22226EAKE4 144 152 216 204 2.5 0.26 3.8 2.6 2.5 11
230 80 3 700 000 1 080 000 71 500 110 000 1 200 1 600 23226CE4 23226CKE4 144 150 216 196 2.5 0.34 2.9 2.0 1.9 14.3
280 93 4 995 000 1 350 000 101 000 137 000 1 300 1 600 22326CE4 22326CKE4 148 166 262 236 3 0.34 2.9 2.0 1.9 28.1
140 210 53 2 420 000 715 000 43 000 73 000 1 600 1 900 23028CDE4 23028CDKE4 150 157 200 190 2 0.22 4.5 3.0 2.9 6.49
210 69 2 525 000 945 000 53 500 96 500 1 300 1 700 24028CE4 24028CK30E4 150 154 200 186 2 0.29 3.4 2.3 2.2 8.37
225 68 2.1 580 000 945 000 59 000 96 500 1 200 1 600 23128CE4 23128CKE4 152 158 213 198 2 0.28 3.6 2.4 2.3 10.5
225 85 2.1 670 000 1 160 000 68 500 118 000 1 200 1 600 24128CE4 24128CK30E4 152 156 213 193 2 0.35 2.9 1.9 1.9 13
250 68 3 645 000 930 000 65 500 95 000 1 400 1 700 22228CDE4 22228CDKE4 154 167 236 219 2.5 0.25 4.0 2.7 2.6 14.5
250 88 3 835 000 1 300 000 85 000 133 000 1 100 1 500 23228CE4 23228CKE4 154 163 236 213 2.5 0.35 2.9 1.9 1.9 18.8
300 102 4 1 160 000 1 590 000 118 000 162 000 1 200 1 500 22328CE4 22328CKE4 158 177 282 253 3 0.35 2.9 1.9 1.9 35.4
150 225 56 2.1 470 000 815 000 48 000 83 000 1 400 1 800 23030CDE4 23030CDKE4 162 168 213 203 2 0.22 4.6 3.1 3.0 7.9
225 75 2.1 590 000 1 090 000 60 500 111 000 1 200 1 500 24030CE4 24030CK30E4 162 165 213 198 2 0.30 3.4 2.3 2.2 10.5
250 80 2.1 725 000 1 180 000 74 000 121 000 1 100 1 400 23130CE4 23130CKE4 162 174 238 218 2 0.30 3.4 2.3 2.2 15.8
250 100 2.1 890 000 1 530 000 91 000 156 000 1 100 1 400 24130CE4 24130CK30E4 162 169 238 212 2 0.38 2.6 1.8 1.7 19.8
270 73 3 765 000 1 120 000 78 000 114 000 1 300 1 600 22230CDE4 22230CDKE4 164 179 256 236 2.5 0.26 3.9 2.6 2.5 18.4
270 96 3 975 000 1 560 000 99 500 159 000 1 100 1 400 23230CE4 23230CKE4 164 176 256 230 2.5 0.35 2.9 1.9 1.9 24.2
320 108 4 1 220 000 1 690 000 125 000 172 000 1 100 1 400 22330CAE4 22330CAKE4 168 302 270 3 0.35 2.9 1.9 1.9 41.5
Note (1) The suffix K or K30 represents bearings with tapered bores (taper 1 : 12 or 1 : 30). Remarks 1. The bearings denoted by an asterisk (*) are NSKHPS bearings and an oil groove and holes are standard for them.
3. For the dimensions of adapters and withdrawal sleeves, refer to Pages B361 B362, and B367 B368.
B 190 B 191
B182-205E.indd 190-191 11/20/13 4:57:52 PM

B B
ra
r r

P =X Fr +Y Fa
jD jd jD jd jD a jd a Fa/ Fre Fa/ Fr>e

X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa
Cylindrical Bore Tapered Bore Without an Oil Groove and Holes given in the table below.

160 220 45 2 360 000 675 000 37 000 69 000 1 400 1 800 23932CAE4 23932CAKE4 170 210 203 2 0.18 5.6 3.8 3.7 4.97
240 60 2.1 540 000 955 000 55 000 97 500 1 300 1 700 23032CDE4 23032CDKE4 172 179 228 216 2 0.22 4.5 3.0 2.9 9.66
240 80 2.1 680 000 1 260 000 69 000 128 000 1 100 1 400 24032CE4 24032CK30E4 172 177 228 212 2 0.30 3.4 2.3 2.2 12.7
270 86 2.1 855 000 1 400 000 87 000 143 000 1 000 1 300 23132CE4 23132CKE4 172 185 258 234 2 0.30 3.4 2.3 2.2 20.3
270 109 2.1 1 040 000 1 760 000 106 000 179 000 1 000 1 300 24132CE4 24132CK30E4 172 179 258 229 2 0.39 2.6 1.7 1.7 25.4
290 80 3 910 000 1 320 000 93 000 135 000 1 200 1 500 22232CDE4 22232CDKE4 174 190 276 255 2.5 0.26 3.8 2.6 2.5 23.1
290 104 3 1 100 000 1 770 000 112 000 180 000 1 000 1 300 23232CE4 23232CKE4 174 189 276 245 2.5 0.34 2.9 2.0 1.9 30.5
340 114 4 1 360 000 1 900 000 139 000 193 000 1 100 1 300 22332CAE4 22332CAKE4 178 322 287 3 0.35 2.9 1.9 1.9 49.3
170 230 45 2 350 000 660 000 35 500 67 500 1 400 1 800 23934BCAE4 23934BCAKE4 180 220 213 2 0.17 5.8 3.9 3.8 5.38
260 67 2.1 640 000 1 090 000 65 000 112 000 1 200 1 600 23034CDE4 23034CDKE4 182 191 248 233 2 0.23 4.3 2.9 2.8 13
260 90 2.1 825 000 1 520 000 84 000 155 000 1 000 1 300 24034CE4 24034CK30E4 182 188 248 228 2 0.31 3.2 2.2 2.1 17.3
280 88 2.1 940 000 1 570 000 96 000 160 000 1 000 1 300 23134CE4 23134CKE4 182 194 268 245 2 0.29 3.5 2.3 2.3 21.8
280 109 2.1 1 080 000 1 860 000 110 000 190 000 1 000 1 300 24134CE4 24134CK30E4 182 190 268 239 2 0.37 2.7 1.8 1.8 26.6
310 86 4 990 000 1 500 000 101 000 153 000 1 100 1 400 22234CDE4 22234CDKE4 188 206 292 270 3 0.26 3.8 2.6 2.5 28.8
310 110 4 1 200 000 1 910 000 122 000 195 000 900 1 200 23234CE4 23234CKE4 188 201 292 261 3 0.34 2.9 2.0 1.9 36.4
360 120 4 1 580 000 2 110 000 161 000 215 000 1 000 1 200 22334CAE4 22334CAKE4 188 342 304 3 0.35 2.9 1.9 1.9 57.9
180 250 52 2 470 000 890 000 48 000 90 500 1 200 1 600 23936CAE4 23936CAKE4 190 240 230 2 0.18 5.5 3.7 3.6 7.64
280 74 2.1 750 000 1 270 000 76 000 129 000 1 200 1 400 23036CDE4 23036CDKE4 192 202 268 249 2 0.24 4.2 2.8 2.8 17.1
280 100 2.1 965 000 1 750 000 98 500 178 000 950 1 200 24036CE4 24036CK30E4 192 200 268 245 2 0.32 3.1 2.1 2.0 22.7
300 96 3 1 050 000 1 760 000 108 000 180 000 900 1 200 23136CE4 23136CKE4 194 206 286 260 2.5 0.30 3.4 2.3 2.2 27.5
300 118 3 1 190 000 2 040 000 121 000 208 000 900 1 200 24136CE4 24136CK30E4 194 202 286 255 2.5 0.37 2.7 1.8 1.8 33.1
320 86 4 1 020 000 1 540 000 104 000 157 000 1 100 1 300 22236CDE4 22236CDKE4 198 212 302 278 3 0.26 3.9 2.6 2.6 30.2
320 112 4 1 300 000 2 110 000 133 000 215 000 850 1 100 23236CE4 23236CKE4 198 211 302 274 3 0.33 3.0 2.0 2.0 38.9
380 126 4 1 740 000 2 340 000 177 000 238 000 950 1 200 22336CAE4 22336CAKE4 198 362 322 3 0.34 2.9 2.0 1.9 67
190 260 52 2 460 000 875 000 47 000 89 500 1 200 1 500 23938CAE4 23938CAKE4 200 250 240 2 0.18 5.7 3.8 3.7 8.03
290 75 2.1 775 000 1 350 000 79 000 138 000 1 100 1 400 23038CAE4 23038CAKE4 202 278 261 2 0.24 4.2 2.8 2.8 17.6
290 100 2.1 975 000 1 840 000 99 500 188 000 900 1 200 24038CE4 24038CK30E4 202 210 278 253 2 0.31 3.2 2.2 2.1 24
320 104 3 1 190 000 2 020 000 121 000 206 000 850 1 100 23138CE4 23138CKE4 204 219 306 276 2.5 0.31 3.3 2.2 2.2 34.5
320 128 3 1 370 000 2 330 000 140 000 238 000 850 1 100 24138CE4 24138CK30E4 204 211 306 269 2.5 0.40 2.5 1.7 1.6 41.5
340 92 4 1 140 000 1 730 000 116 000 176 000 1 000 1 200 22238CAE4 22238CAKE4 208 322 296 3 0.26 3.8 2.6 2.5 35.5
340 120 4 1 440 000 2 350 000 147 000 240 000 800 1 100 23238CE4 23238CKE4 208 222 322 288 3 0.35 2.9 1.9 1.9 47.6
400 132 5 1 890 000 2 590 000 193 000 264 000 900 1 100 22338CAE4 22338CAKE4 212 378 338 4 0.34 2.9 2.0 1.9 77.6
Note (1) The suffix K or K30 represents bearings with tapered bores (taper 1 : 12 or 1 : 30). Remarks For the dimensions of adapters and withdrawal sleeves, refer to Pages B362 and B368.
B 192 B 193
B182-205E.indd 192-193 11/20/13 4:57:53 PM

B B
ra
r r

P =X Fr +Y Fa

X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa
Cylindrical Bore Tapered Bore Without an Oil Groove and Holes given in the table below.

200 280 60 2.1 570 000 1 060 000 58 000 108 000 1 100 1 400 23940CAE4 23940CAKE4 212 268 258 2 0.20 5.1 3.4 3.3 11
310 82 2.1 940 000 1 700 000 96 000 174 000 1 000 1 300 23040CAE4 23040CAKE4 212 298 279 2 0.25 4.0 2.7 2.6 22.6
310 109 2.1 1 140 000 2 120 000 116 000 216 000 850 1 100 24040CE4 24040CK30E4 212 223 298 271 2 0.32 3.1 2.1 2.0 30.4
340 112 3 1 360 000 2 330 000 139 000 238 000 800 1 000 23140CE4 23140CKE4 214 232 326 293 2.5 0.31 3.2 2.2 2.1 42.7
340 140 3 1 570 000 2 670 000 160 000 272 000 800 1 000 24140CE4 24140CK30E4 214 226 326 290 2.5 0.39 2.6 1.8 1.7 51.3
360 98 4 1 300 000 2 010 000 133 000 204 000 950 1 200 22240CAE4 22240CAKE4 218 342 315 3 0.26 3.8 2.6 2.5 42.6
360 128 4 1 660 000 2 750 000 169 000 281 000 750 1 000 23240CE4 23240CKE4 218 237 342 307 3 0.34 2.9 2.0 1.9 57.1
420 138 5 2 000 000 2 990 000 204 000 305 000 850 1 000 22340CAE4 22340CAKE4 222 398 352 4 0.34 2.9 2.0 1.9 92.6
220 300 60 2.1 625 000 1 240 000 64 000 126 000 1 000 1 300 23944CAE4 23944CAKE4 232 288 278 2 0.18 5.7 3.8 3.7 12.2
340 90 3 1 090 000 1 980 000 111 000 202 000 950 1 200 23044CAE4 23044CAKE4 234 326 302 2.5 0.24 4.1 2.8 2.7 29.7
340 118 3 1 360 000 2 600 000 138 000 265 000 750 1 000 24044CE4 24044CK30E4 234 244 326 296 2.5 0.31 3.2 2.1 2.1 40.5
370 120 4 1 570 000 2 710 000 160 000 276 000 710 950 23144CE4 23144CKE4 238 254 352 320 3 0.30 3.3 2.2 2.2 53
370 150 4 1 800 000 3 200 000 183 000 325 000 710 950 24144CE4 24144CK30E4 238 248 352 313 3 0.39 2.6 1.7 1.7 66.7
400 108 4 1 570 000 2 430 000 160 000 247 000 850 1 000 22244CAE4 22244CAKE4 238 382 348 3 0.27 3.7 2.5 2.4 59
400 144 4 2 020 000 3 400 000 206 000 350 000 670 900 23244CE4 23244CKE4 238 260 382 337 3 0.35 2.9 1.9 1.9 80.4
460 145 5 2 350 000 3 400 000 240 000 345 000 750 950 22344CAE4 22344CAKE4 242 438 391 4 0.33 3.0 2.0 2.0 116
240 320 60 2.1 635 000 1 300 000 65 000 133 000 950 1 200 23948CAE4 23948CAKE4 252 308 298 2 0.17 6.0 4.0 3.9 13.3
360 92 3 1 160 000 2 140 000 118 000 218 000 850 1 100 23048CAE4 23048CAKE4 254 346 324 2.5 0.24 4.2 2.8 2.7 32.6
360 118 3 1 390 000 2 730 000 141 000 278 000 710 950 24048CE4 24048CK30E4 254 265 346 317 2.5 0.29 3.4 2.3 2.2 43.4
400 128 4 1 790 000 3 100 000 182 000 320 000 670 850 23148CE4 23148CKE4 258 275 382 347 3 0.30 3.3 2.2 2.2 66.9
400 160 4 2 130 000 3 800 000 217 000 385 000 670 850 24148CE4 24148CK30E4 258 268 382 341 3 0.38 2.7 1.8 1.8 79.5
440 120 4 1 870 000 2 890 000 191 000 294 000 750 950 22248CAE4 22248CAKE4 258 422 383 3 0.27 3.7 2.5 2.4 80.2
440 160 4 2 440 000 4 050 000 249 000 415 000 630 800 23248CAE4 23248CAKE4 258 422 372 3 0.37 2.7 1.8 1.8 106
500 155 5 2 600 000 3 800 000 265 000 385 000 670 850 22348CAE4 22348CAKE4 262 478 423 4 0.32 3.2 2.1 2.1 147
260 360 75 2.1 930 000 1 870 000 95 000 191 000 850 1 000 23952CAE4 23952CAKE4 272 348 333 2 0.19 5.4 3.6 3.5 23
400 104 4 1 430 000 2 580 000 145 000 263 000 800 950 23052CAE4 23052CAKE4 278 382 356 3 0.25 4.1 2.7 2.7 46.6
400 140 4 1 810 000 3 500 000 185 000 360 000 630 850 24052CAE4 24052CAK30E4 278 382 348 3 0.32 3.1 2.1 2.1 62.6
440 144 4 2 160 000 3 750 000 221 000 385 000 600 800 23152CAE4 23152CAKE4 278 422 380 3 0.32 3.2 2.1 2.1 88.2
440 180 4 2 560 000 4 700 000 261 000 480 000 600 800 24152CAE4 24152CAK30E4 278 422 371 3 0.39 2.6 1.7 1.7 109
480 130 5 2 180 000 3 400 000 222 000 345 000 670 850 22252CAE4 22252CAKE4 282 458 418 4 0.27 3.7 2.5 2.5 104
480 174 5 2 740 000 4 550 000 279 000 460 000 560 750 23252CAE4 23252CAKE4 282 458 406 4 0.37 2.7 1.8 1.8 137
540 165 6 3 100 000 4 600 000 320 000 470 000 630 800 22352CAE4 22352CAKE4 288 512 462 5 0.32 3.2 2.1 2.1 180
B 194 B 195
B182-205E.indd 194-195 11/20/13 4:57:54 PM

B B
ra
r r

P =X Fr +Y Fa

X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa
Cylindrical Bore Tapered Bore Without an Oil Groove and Holes

min. min. max. min. max. approx.
280 380 75 2.1 925 000 1 950 000 94 500 199 000 800 950 23956CAE4 23956CAKE4 292 368 351 2 0.18 5.7 3.9 3.8 24.5
420 106 4 1 540 000 2 950 000 157 000 300 000 710 900 23056CAE4 23056CAKE4 298 402 377 3 0.24 4.2 2.8 2.7 50.5
420 140 4 1 880 000 3 800 000 191 000 385 000 600 800 24056CAE4 24056CAK30E4 298 402 369 3 0.31 3.3 2.2 2.2 66.4
460 146 5 2 230 000 4 000 000 228 000 410 000 560 750 23156CAE4 23156CAKE4 302 438 400 4 0.30 3.3 2.2 2.2 94.3
460 180 5 2 640 000 5 000 000 269 000 505 000 560 750 24156CAE4 24156CAK30E4 302 438 392 4 0.37 2.7 1.8 1.8 115
500 130 5 2 280 000 3 650 000 233 000 370 000 630 800 22256CAE4 22256CAKE4 302 478 439 4 0.25 4.0 2.7 2.6 110
500 176 5 2 880 000 4 900 000 294 000 500 000 530 670 23256CAE4 23256CAKE4 302 478 425 4 0.35 2.9 1.9 1.9 147
580 175 6 3 500 000 5 150 000 355 000 525 000 560 710 22356CAE4 22356CAKE4 308 552 496 5 0.31 3.2 2.1 2.1 221
300 420 90 3 1 230 000 2 490 000 125 000 254 000 710 900 23960CAE4 23960CAKE4 314 406 386 2.5 0.19 5.2 3.5 3.4 38.2
460 118 4 1 920 000 3 700 000 196 000 375 000 670 850 23060CAE4 23060CAKE4 318 442 413 3 0.24 4.2 2.8 2.7 70.5
460 160 4 2 310 000 4 600 000 235 000 470 000 530 710 24060CAE4 24060CAK30E4 318 442 400 3 0.32 3.1 2.1 2.0 93.6
500 160 5 2 670 000 4 800 000 273 000 490 000 500 670 23160CAE4 23160CAKE4 322 478 433 4 0.31 3.3 2.2 2.2 125
500 200 5 3 100 000 5 800 000 315 000 595 000 500 670 24160CAE4 24160CAK30E4 322 478 423 4 0.38 2.6 1.8 1.7 152
540 140 5 2 610 000 4 250 000 266 000 430 000 600 750 22260CAE4 22260CAKE4 322 518 473 4 0.25 4.0 2.7 2.6 139
540 192 5 3 400 000 5 900 000 350 000 600 000 480 630 23260CAE4 23260CAKE4 322 518 458 4 0.35 2.9 1.9 1.9 189
320 440 90 3 1 300 000 2 750 000 132 000 281 000 670 850 23964CAE4 23964CAKE4 334 426 406 2.5 0.18 5.5 3.7 3.6 40.6
480 121 4 1 960 000 3 850 000 200 000 395 000 630 800 23064CAE4 23064CAKE4 338 462 432 3 0.24 4.2 2.8 2.8 75.6
480 160 4 2 440 000 5 050 000 249 000 515 000 500 670 24064CAE4 24064CAK30E4 338 462 422 3 0.31 3.3 2.2 2.2 99.7
540 176 5 3 050 000 5 500 000 315 000 560 000 480 600 23164CAE4 23164CAKE4 342 518 466 4 0.31 3.2 2.1 2.1 162
540 218 5 3 550 000 6 650 000 360 000 675 000 480 600 24164CAE4 24164CAK30E4 342 518 456 4 0.39 2.6 1.7 1.7 196
580 150 5 2 990 000 4 850 000 305 000 495 000 530 670 22264CAE4 22264CAKE4 342 558 508 4 0.26 3.9 2.6 2.6 174
580 208 5 3 900 000 6 900 000 395 000 700 000 450 600 23264CAE4 23264CAKE4 342 558 488 4 0.36 2.8 1.9 1.8 239
340 460 90 3 1 330 000 2 840 000 136 000 289 000 630 800 23968CAE4 23968CAKE4 354 446 427 2.5 0.18 5.7 3.8 3.7 42.4
520 133 5 2 280 000 4 400 000 232 000 445 000 560 710 23068CAE4 23068CAKE4 362 498 465 4 0.24 4.2 2.8 2.8 101
520 180 5 2 920 000 6 050 000 298 000 615 000 480 600 24068CAE4 24068CAK30E4 362 498 454 4 0.32 3.2 2.1 2.1 135
580 190 5 3 600 000 6 600 000 370 000 670 000 430 560 23168CAE4 23168CAKE4 362 558 499 4 0.31 3.2 2.1 2.1 206
580 243 5 4 250 000 7 900 000 430 000 810 000 430 560 24168CAE4 24168CAK30E4 362 558 489 4 0.40 2.5 1.7 1.7 257
620 224 6 4 400 000 7 800 000 450 000 795 000 400 530 23268CAE4 23268CAKE4 368 592 521 5 0.36 2.8 1.9 1.8 295
Note (1) The suffix K or K30 represents bearings with tapered bores (taper 1 : 12 or 1 : 30). Remarks For the dimensions of adapters and withdrawal sleeves, refer to Pages B363 B364, and B369 B370.
B 196 B 197
B182-205E.indd 196-197 11/20/13 4:57:55 PM

B B
ra
r r

P =X Fr +Y Fa

X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa

360 480 90 3 1 390 000 3 050 000 142 000 315 000 600 750 23972CAE4 23972CAKE4 374 466 447 2.5 0.17 6.0 4.1 4.0 44.7
540 134 5 2 390 000 4 700 000 244 000 480 000 530 670 23072CAE4 23072CAKE4 382 518 485 4 0.24 4.2 2.8 2.8 106
540 180 5 2 930 000 6 100 000 299 000 625 000 450 600 24072CAE4 24072CAK30E4 382 518 476 4 0.32 3.2 2.1 2.1 139
600 192 5 3 800 000 7 100 000 390 000 725 000 400 530 23172CAE4 23172CAKE4 382 578 520 4 0.31 3.2 2.2 2.1 217
600 243 5 4 200 000 8 000 000 430 000 815 000 400 530 24172CAE4 24172CAK30E4 382 578 507 4 0.40 2.5 1.7 1.7 264
650 232 6 4 800 000 8 550 000 490 000 870 000 380 500 23272CAE4 23272CAKE4 388 622 549 5 0.36 2.8 1.9 1.8 342
380 520 106 4 1 870 000 4 100 000 190 000 420 000 530 670 23976CAE4 23976CAKE4 398 502 482 3 0.18 5.5 3.7 3.6 65.4
560 135 5 2 500 000 5 100 000 255 000 520 000 530 630 23076CAE4 23076CAKE4 402 538 506 4 0.22 4.5 3.0 3.0 113
560 180 5 3 050 000 6 600 000 315 000 670 000 430 560 24076CAE4 24076CAK30E4 402 538 496 4 0.29 3.4 2.3 2.3 148
620 194 5 4 000 000 7 600 000 405 000 775 000 400 500 23176CAE4 23176CAKE4 402 598 540 4 0.30 3.3 2.2 2.2 229
620 243 5 4 350 000 8 450 000 440 000 865 000 400 500 24176CAE4 24176CAK30E4 402 598 529 4 0.38 2.6 1.8 1.7 275
680 240 6 5 150 000 9 200 000 525 000 940 000 360 480 23276CAE4 23276CAKE4 408 652 578 5 0.35 2.9 1.9 1.9 372
400 540 106 4 1 890 000 4 250 000 193 000 435 000 530 630 23980CAE4 23980CAKE4 418 522 501 3 0.18 5.7 3.9 3.8 69.1
600 148 5 2 970 000 5 900 000 305 000 605 000 480 600 23080CAE4 23080CAKE4 422 578 540 4 0.23 4.4 3.0 2.9 146
600 200 5 3 600 000 7 600 000 370 000 775 000 400 500 24080CAE4 24080CAK30E4 422 578 527 4 0.31 3.3 2.2 2.2 193
650 200 6 4 150 000 7 900 000 420 000 805 000 380 480 23180CAE4 23180CAKE4 428 622 569 5 0.29 3.4 2.3 2.3 257
650 250 6 4 950 000 10 100 000 505 000 1 030 000 380 480 24180CAE4 24180CAK30E4 428 622 551 5 0.37 2.7 1.8 1.8 316
720 256 6 5 800 000 10 400 000 590 000 1 060 000 340 450 23280CAE4 23280CAKE4 428 692 610 5 0.36 2.8 1.9 1.9 449
420 560 106 4 1 870 000 4 250 000 191 000 430 000 500 600 23984CAE4 23984CAKE4 438 542 521 3 0.17 6.0 4.0 3.9 71.6
620 150 5 2 910 000 5 850 000 297 000 595 000 450 560 23084CAE4 23084CAKE4 442 598 562 4 0.23 4.3 2.9 2.8 151
620 200 5 3 750 000 8 100 000 380 000 825 000 380 480 24084CAE4 24084CAK30E4 442 598 549 4 0.31 3.2 2.2 2.1 199
700 224 6 5 000 000 9 400 000 510 000 960 000 340 450 23184CAE4 23184CAKE4 448 672 607 5 0.31 3.3 2.2 2.2 341
700 280 6 6 000 000 12 000 000 610 000 1 220 000 340 450 24184CAE4 24184CAK30E4 448 672 598 5 0.38 2.6 1.8 1.7 421
760 272 7.5 6 450 000 11 700 000 660 000 1 190 000 320 430 23284CAE4 23284CAKE4 456 724 644 6 0.35 2.9 1.9 1.9 534
440 600 118 4 2 190 000 4 800 000 223 000 490 000 450 560 23988CAE4 23988CAKE4 458 582 555 3 0.18 5.7 3.9 3.8 96.3
650 157 6 3 150 000 6 350 000 320 000 645 000 430 530 23088CAE4 23088CAKE4 468 622 587 5 0.23 4.3 2.9 2.8 173
650 212 6 4 150 000 9 100 000 425 000 930 000 360 450 24088CAE4 24088CAK30E4 468 622 576 5 0.31 3.2 2.1 2.1 237
720 226 6 5 300 000 10 300 000 540 000 1 060 000 320 430 23188CAE4 23188CAKE4 468 692 627 5 0.3 3.3 2.2 2.2 360
720 280 6 6 000 000 12 100 000 610 000 1 230 000 320 430 24188CAE4 24188CAK30E4 468 692 617 5 0.37 2.7 1.8 1.8 433
790 280 7.5 6 900 000 12 800 000 705 000 1 300 000 300 400 23288CAE4 23288CAKE4 476 754 669 6 0.35 2.9 1.9 1.9 594
Note (1) The suffix K or K30 represents bearings with tapered bores (taper 1 : 12 or 1 : 30). Remarks For the dimensions of adapters and withdrawal sleeves, refer to Pages B364, and B370 B371.
B 198 B 199
B182-205E.indd 198-199 11/20/13 4:57:56 PM

B B
ra
r r

P =X Fr +Y Fa

X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa

460 620 118 4 2 220 000 4 950 000 227 000 505 000 430 530 23992CAE4 23992CAKE4 478 602 575 3 0.17 5.9 4.0 3.9 100
680 163 6 3 450 000 7 100 000 355 000 725 000 400 500 23092CAE4 23092CAKE4 488 652 615 5 0.22 4.6 3.1 3.0 201
680 218 6 4 500 000 9 950 000 460 000 1 010 000 340 430 24092CAE4 24092CAK30E4 488 652 604 5 0.29 3.4 2.3 2.3 266
760 240 7.5 5 700 000 10 900 000 580 000 1 110 000 300 400 23192CAE4 23192CAKE4 496 724 661 6 0.31 3.3 2.2 2.2 423
760 300 7.5 6 300 000 12 400 000 640 000 1 270 000 300 400 24192CAE4 24192CAK30E4 496 724 646 6 0.39 2.6 1.7 1.7 512
830 296 7.5 7 350 000 13 700 000 750 000 1 400 000 280 380 23292CAE4 23292CAKE4 496 794 702 6 0.36 2.8 1.9 1.8 691
480 650 128 5 2 580 000 5 850 000 263 000 595 000 400 500 23996CAE4 23996CAKE4 502 628 602 4 0.18 5.7 3.8 3.7 121
700 165 6 3 800 000 7 950 000 385 000 810 000 400 480 23096CAE4 23096CAKE4 508 672 633 5 0.22 4.6 3.1 3.0 211
700 218 6 4 600 000 10 200 000 470 000 1 040 000 320 430 24096CAE4 24096CAK30E4 508 672 625 5 0.30 3.4 2.3 2.2 270
790 248 7.5 6 050 000 11 700 000 620 000 1 200 000 300 380 23196CAE4 23196CAKE4 516 754 688 6 0.31 3.3 2.2 2.2 475
790 308 7.5 7 150 000 14 600 000 730 000 1 490 000 300 380 24196CAE4 24196CAK30E4 516 754 670 6 0.39 2.6 1.7 1.7 567
870 310 7.5 7 850 000 14 400 000 805 000 1 470 000 260 360 23296CAE4 23296CAKE4 516 834 733 6 0.36 2.8 1.9 1.8 795
500 670 128 5 2 460 000 5 550 000 250 000 565 000 400 500 239/500CAE4 239/500CAKE4 522 648 622 4 0.17 6.0 4.0 3.9 124
720 167 6 3 750 000 8 100 000 385 000 825 000 380 480 230/500CAE4 230/500CAKE4 528 692 655 5 0.21 4.8 3.2 3.1 220
720 218 6 4 450 000 9 900 000 450 000 1 010 000 300 400 240/500CAE4 240/500CAK30E4 528 692 643 5 0.30 3.4 2.3 2.2 276
830 264 7.5 6 850 000 13 400 000 700 000 1 360 000 280 360 231/500CAE4 231/500CAKE4 536 794 720 6 0.31 3.2 2.2 2.1 567
830 325 7.5 8 000 000 16 000 000 815 000 1 630 000 280 360 241/500CAE4 241/500CAK30E4 536 794 703 6 0.39 2.6 1.7 1.7 666
920 336 7.5 9 000 000 16 600 000 915 000 1 690 000 260 320 232/500CAE4 232/500CAKE4 536 884 773 6 0.38 2.7 1.8 1.8 969
530 710 136 5 2 930 000 6 800 000 299 000 695 000 360 450 239/530CAE4 239/530CAKE4 552 688 659 4 0.17 6.0 4.0 3.9 149
780 185 6 4 400 000 9 200 000 450 000 940 000 340 430 230/530CAE4 230/530CAKE4 558 752 706 5 0.22 4.6 3.1 3.0 298
780 250 6 5 400 000 11 800 000 550 000 1 210 000 280 360 240/530CAE4 240/530CAK30E4 558 752 690 5 0.31 3.3 2.2 2.2 390
870 272 7.5 7 150 000 14 100 000 730 000 1 440 000 260 340 231/530CAE4 231/530CAKE4 566 834 758 6 0.30 3.3 2.2 2.2 628
870 335 7.5 8 500 000 17 500 000 870 000 1 790 000 260 340 241/530CAE4 241/530CAK30E4 566 834 740 6 0.38 2.6 1.8 1.7 773
980 355 9.5 10 100 000 18 800 000 1 030 000 1 920 000 240 300 232/530CAE4 232/530CAKE4 574 936 824 8 0.38 2.7 1.8 1.7 1 170
560 750 140 5 3 100 000 7 250 000 320 000 740 000 340 430 239/560CAE4 239/560CAKE4 582 728 697 4 0.16 6.1 4.1 4.0 172
820 195 6 5 000 000 10 700 000 510 000 1 090 000 320 400 230/560CAE4 230/560CAKE4 588 792 742 5 0.22 4.5 3.0 2.9 344
820 258 6 5 950 000 13 300 000 605 000 1 360 000 260 340 240/560CAE4 240/560CAK30E4 588 792 729 5 0.30 3.3 2.2 2.2 440
920 280 7.5 7 850 000 15 500 000 800 000 1 580 000 240 320 231/560CAE4 231/560CAKE4 596 884 804 6 0.30 3.4 2.3 2.2 727
920 355 7.5 9 400 000 19 600 000 960 000 2 000 000 240 320 241/560CAE4 241/560CAK30E4 596 884 782 6 0.39 2.6 1.8 1.7 886
1 030 365 9.5 10 900 000 20 500 000 1 110 000 2 090 000 220 280 232/560CAE4 232/560CAKE4 604 986 870 8 0.36 2.8 1.9 1.8 1 320
B 200 B 201
B182-205E.indd 200-201 11/20/13 4:57:57 PM

B B
ra
r r

P =X Fr +Y Fa

X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa

600 800 150 5 3 450 000 8 100 000 350 000 830 000 320 400 239/600CAE4 239/600CAKE4 622 778 745 4 0.17 5.9 3.9 3.9 205
870 200 6 5 450 000 12 200 000 555 000 1 240 000 300 360 230/600CAE4 230/600CAKE4 628 842 794 5 0.21 4.8 3.3 3.2 389
870 272 6 6 600 000 15 100 000 675 000 1 540 000 240 320 240/600CAE4 240/600CAK30E4 628 842 772 5 0.30 3.3 2.2 2.2 529
980 300 7.5 8 750 000 17 500 000 895 000 1 790 000 220 280 231/600CAE4 231/600CAKE4 636 944 856 6 0.30 3.4 2.3 2.2 898
980 375 7.5 10 400 000 21 900 000 1 060 000 2 230 000 220 280 241/600CAE4 241/600CAK30E4 636 944 836 6 0.39 2.6 1.8 1.7 1 050
1 090 388 9.5 12 700 000 24 900 000 1 300 000 2 540 000 200 260 232/600CAE4 232/600CAKE4 644 1 046 923 8 0.36 2.8 1.9 1.8 1 590
630 850 165 6 4 000 000 9 350 000 405 000 950 000 300 360 239/630CAE4 239/630CAKE4 658 822 786 5 0.18 5.6 3.8 3.7 259
920 212 7.5 5 900 000 12 700 000 600 000 1 300 000 280 340 230/630CAE4 230/630CAKE4 666 884 835 6 0.22 4.7 3.1 3.1 468
920 290 7.5 7 550 000 17 700 000 770 000 1 810 000 220 300 240/630CAE4 240/630CAK30E4 666 884 815 6 0.30 3.3 2.2 2.2 637
1 030 315 7.5 9 600 000 19 400 000 980 000 1 970 000 200 260 231/630CAE4 231/630CAKE4 666 994 900 6 0.30 3.4 2.3 2.2 1 040
1 030 400 7.5 11 300 000 23 900 000 1 160 000 2 440 000 200 260 241/630CAE4 241/630CAK30E4 666 994 876 6 0.38 2.7 1.8 1.7 1 250
1 150 412 12 13 400 000 25 600 000 1 370 000 2 610 000 180 240 232/630CAE4 232/630CAKE4 684 1 096 970 10 0.36 2.8 1.9 1.8 1 850
670 900 170 6 4 350 000 10 300 000 445 000 1 050 000 260 340 239/670CAE4 239/670CAKE4 698 872 836 5 0.17 5.8 3.9 3.8 300
980 230 7.5 6 850 000 15 000 000 700 000 1 530 000 240 320 230/670CAE4 230/670CAKE4 706 944 891 6 0.22 4.7 3.1 3.1 571
980 308 7.5 8 450 000 19 500 000 860 000 1 990 000 200 260 240/670CAE4 240/670CAK30E4 706 944 868 6 0.30 3.3 2.2 2.2 773
1 090 336 7.5 10 600 000 21 600 000 1 080 000 2 200 000 190 240 231/670CAE4 231/670CAKE4 706 1 054 952 6 0.30 3.3 2.2 2.2 1 230
1 090 412 7.5 12 400 000 26 500 000 1 270 000 2 700 000 190 240 241/670CAE4 241/670CAK30E4 706 1 054 934 6 0.37 2.7 1.8 1.8 1 440
1 220 438 12 14 900 000 28 700 000 1 520 000 2 920 000 170 220 232/670CAE4 232/670CAKE4 724 1 166 1 024 10 0.37 2.7 1.8 1.8 2 210
710 950 180 6 4 800 000 11 700 000 490 000 1 200 000 240 300 239/710CAE4 239/710CAKE4 738 922 883 5 0.17 5.8 3.9 3.8 352
1 030 236 7.5 7 100 000 15 800 000 725 000 1 610 000 240 280 230/710CAE4 230/710CAKE4 746 994 936 6 0.22 4.6 3.1 3.0 647
1 030 315 7.5 8 850 000 20 700 000 905 000 2 110 000 190 240 240/710CAE4 240/710CAK30E4 746 994 916 6 0.29 3.4 2.3 2.2 861
1 150 438 9.5 13 900 000 30 500 000 1 410 000 3 100 000 170 220 241/710CAE4 241/710CAK30E4 754 1 106 981 8 0.38 2.6 1.8 1.7 1 730
1 280 450 12 15 700 000 30 500 000 1 600 000 3 100 000 160 200 232/710CAE4 232/710CAKE4 764 1 226 1 080 10 0.36 2.8 1.9 1.8 2 470
750 1 000 185 6 5 250 000 12 800 000 535 000 1 310 000 220 280 239/750CAE4 239/750CAKE4 778 972 931 5 0.17 6.0 4.1 4.0 398
1 090 250 7.5 7 750 000 17 200 000 790 000 1 750 000 220 260 230/750CAE4 230/750CAKE4 786 1 054 990 6 0.22 4.6 3.1 3.0 768
1 090 335 7.5 10 100 000 24 000 000 1 030 000 2 450 000 180 220 240/750CAE4 240/750CAK30E4 786 1 054 969 6 0.29 3.4 2.3 2.2 1 030
1 360 475 15 17 700 000 35 500 000 1 800 000 3 600 000 140 190 232/750CAE4 232/750CAKE4 814 1 296 1 148 12 0.36 2.8 1.9 1.8 2 980
800 1 060 195 6 5 600 000 13 700 000 570 000 1 400 000 220 260 239/800CAE4 239/800CAKE4 828 1 032 987 5 0.17 6.0 4.0 3.9 462
1 150 258 7.5 8 350 000 19 100 000 850 000 1 950 000 200 240 230/800CAE4 230/800CAKE4 836 1 114 1 045 6 0.21 4.7 3.2 3.1 870
1 150 345 7.5 10 900 000 26 300 000 1 110 000 2 680 000 160 200 240/800CAE4 240/800CAK30E4 836 1 114 1 029 6 0.27 3.7 2.5 2.5 1 130
1 280 375 9.5 13 800 000 29 200 000 1 410 000 2 970 000 150 190 231/800CAE4 231/800CAKE4 844 1 236 1 127 8 0.28 3.6 2.4 2.3 1870
1 420 488 15 20 300 000 41 000 000 2 070 000 4 150 000 130 170 232/800CAE4 232/800CAKE4 864 1 356 1 208 12 0.35 2.8 1.9 1.9 3 250
Note (1) The suffix K or K30 represents bearings with tapered bores (taper 1 : 12 or 1 : 30).
B 202 B 203
B182-205E.indd 202-203 11/20/13 4:57:57 PM

B B
ra
r r

P =X Fr +Y Fa

X Y X Y
1 Y3 0.67 Y2
P0 = Fr +Y0 Fa

850 1 120 200 6 6 100 000 15 200 000 620 000 1 550 000 190 240 239/850CAE4 239/850CAKE4 878 1 092 1 046 5 0.16 6.2 4.2 4.1 523
1 220 272 7.5 9 300 000 21 400 000 945 000 2 190 000 180 220 230/850CAE4 230/850CAKE4 886 1 184 1 109 6 0.21 4.8 3.2 3.1 1 020
1 220 365 7.5 11 600 000 28 300 000 1 180 000 2 890 000 150 190 240/850CAE4 240/850CAK30E4 886 1 184 1 093 6 0.28 3.6 2.4 2.4 1 350
1 500 515 15 22 300 000 45 500 000 2 270 000 4 650 000 120 160 232/850CAE4 232/850CAKE4 914 1 436 1 274 12 0.35 2.8 1.9 1.9 3 890
900 1 180 206 6 6 600 000 16 700 000 670 000 1 700 000 180 220 239/900CAE4 239/900CAKE4 928 1 152 1 103 5 0.16 6.4 4.3 4.2 591
1 280 280 7.5 9 850 000 22 800 000 1 000 000 2 330 000 160 200 230/900CAE4 230/900CAKE4 936 1 244 1 169 6 0.20 4.9 3.3 3.2 1 160
1 280 375 7.5 12 800 000 31 500 000 1 300 000 3 250 000 140 180 240/900CAE4 240/900CAK30E4 936 1 244 1 147 6 0.28 3.6 2.4 2.4 1 520
1 580 515 15 23 400 000 47 500 000 2 380 000 4 850 000 110 140 232/900CAE4 232/900CAKE4 964 1 516 1 354 12 0.33 3.0 2.0 2.0 4 300
950 1 250 224 7.5 7 600 000 19 900 000 775 000 2 030 000 160 200 239/950CAE4 239/950CAKE4 986 1 214 1 169 6 0.16 6.3 4.2 4.1 732
1 360 300 7.5 11 300 000 26 500 000 1 160 000 2 710 000 150 190 230/950CAE4 230/950CAKE4 986 1 324 1 241 6 0.21 4.8 3.2 3.2 1 400
1 360 412 7.5 14 500 000 36 500 000 1 480 000 3 700 000 120 160 240/950CAE4 240/950CAK30E4 986 1 324 1 219 6 0.28 3.6 2.4 2.3 1 880
1 660 530 15 24 700 000 50 500 000 2 520 000 5 150 000 100 130 232/950CAE4 232/950CAKE4 1 014 1 596 1 428 12 0.32 3.1 2.1 2.1 4 800
1 000 1 320 236 7.5 8 200 000 21 700 000 835 000 2 210 000 150 190 239/1000CAE4 239/1000CAKE4 1 036 1 284 1 229 6 0.16 6.4 4.3 4.2 881
1 420 308 7.5 11 900 000 28 100 000 1 210 000 2 860 000 140 170 230/1000CAE4 230/1000CAKE4 1 036 1 384 1 298 6 0.20 4.9 3.3 3.2 1 560
1 420 412 7.5 15 300 000 38 500 000 1 560 000 3 950 000 110 150 240/1000CAE4 240/1000CAK30E4 1 036 1 384 1 275 6 0.27 3.7 2.5 2.4 2 010
1 060 1 400 250 7.5 9 300 000 24 400 000 950 000 2 490 000 130 170 239/1060CAE4 239/1060CAKE4 1 096 1 364 1 302 6 0.16 6.1 4.1 4.0 1 030
1 500 325 9.5 13 000 000 31 500 000 1 330 000 3 200 000 120 160 230/1060CAE4 230/1060CAKE4 1 104 1 456 1 368 8 0.21 4.9 3.3 3.2 1 790
1 500 438 9.5 16 800 000 43 000 000 1 720 000 4 350 000 100 130 240/1060CAE4 240/1060CAK30E4 1 104 1 456 1 346 8 0.28 3.6 2.4 2.4 2 410
1 120 1 580 345 9.5 15 400 000 38 000 000 1 570 000 3 850 000 110 140 230/1120CAE4 230/1120CAKE4 1 164 1 536 1 444 8 0.20 5.0 3.4 3.3 2 120
1 580 462 9.5 18 700 000 49 500 000 1 910 000 5 050 000 95 120 240/1120CAE4 240/1120CAK30E4 1 164 1 536 1 421 8 0.27 3.7 2.5 2.5 2 790
1 180 1 660 475 9.5 20 200 000 52 500 000 2 060 000 5 350 000 85 110 240/1180CAE4 240/1180CAK30E4 1 224 1 616 1 494 8 0.27 3.7 2.5 2.4 3 180
1 250 1 750 500 9.5 21 000 000 59 500 000 2 140 000 6 050 000 75 100 240/1250CAE4 240/1250CAK30E4 1 294 1 706 1 579 8 0.25 4.0 2.7 2.6 3 700
1 320 1 850 530 12 22 600 000 63 500 000 2 310 000 6 500 000 67 85 240/1320CAE4 240/1320CAK30E4 1 374 1 796 1 656 10 0.26 3.9 2.6 2.6 4 400
1 400 1 950 545 12 24 500 000 65 000 000 2 500 000 6 650 000 60 75 240/1400CAE4 240/1400CAK30E4 1 454 1 896 1 767 10 0.25 4.0 2.7 2.6 4 900
Note (1) The suffix K or K30 represents bearings with tapered bores (taper 1 : 12 or 1 : 30).
B 204 B 205
B182-205E.indd 204-205 11/20/13 4:57:58 PM

THRUST BEARINGS
SINGLE-DIRECTION THRUST BALL BEARINGS
With Flat Seat, Aligning Seat, or Aligning Seat Washer Bore Diameter 10 100mm B210
DOUBLE-DIRECTION THRUST BALL BEARINGS

With Flat Seat, Aligning Seat, or Aligning Seat Washer Bore Diameter 10 190mm B218
THRUST CYLINDRICAL ROLLER BEARINGS Bore Diameter 35 320mm B224
THRUST SPHERICAL ROLLER BEARINGS Bore Diameter 60 500mm B228
Angular Contact Thrust Ball Bearings are described on pages B234 to B243.

THRUST BALL BEARINGS
Thrust ball bearings are classified into those with flat seats or aligning seats
depending on the shape of the outer ring seat (housing washer). They can
sustain axial loads but no radial loads.
The series of thrust ball bearings available are shown in Table 1.
For Single-Direction Thrust Ball Bearings, pressed steel cages and machined
brass cages are usually used as shown in Table 2. The cages in Double-
Direction Thrust Ball Bearings are the same as those in Single-Direction Thrust
Ball Bearings of the same diameter series.
The basic load ratings listed in the bearing tables are based on the standard
cage type shown in Table 2. If the type of cage is different for bearings with the
same number, the number of balls may vary, in such a case, the load rating will
differ from the one listed in the bearing tables.
Table1 Series of Thrust Ball Table 2 Standard Cages for Thrust Ball
Bearings Bearings
W/Aligning
W/Flat W/Aligning
Seat Pressed Steel Machined Brass
Seat Seat
Washer
511
51100 51152X 51156X 51172X
Single- 512 532 532U 51200 51236X 51238X 51272X
Direction 513 533 533U 51305 51336X 51338X 51340X
514 534 534U
51405 51418X 51420X 51436X
522 542 542U 53200 53236X 53238X 53272X
Double-
523 543 543U 53305 53336X 53338X 53340X
Direction 53405 53418X 53420X 53436X
524 544 544U
B 206 B 207
B206-233E.indd 206-207 11/20/13 4:58:19 PM

THRUST CYLINDRICAL ROLLER BEARINGS DIMENSIONS RELATED TO MOUNTING
These are thrust bearings containing cylindrical rollers. They can sustain
only axial loads, but they are suitable for heavy loads and have high axial The dimensions related to mounting of thrust spherical roller bearings are
rigidity. listed in the Bearing Table.
The cages are machined brass. If the bearing load is heavy, it is necessary to design the shaft shoulder
with ample strength in order to provide sufficient support for the shaft
THRUST SPHERICAL ROLLER BEARINGS washer.
These are thrust bearings containing convex rollers. They have a self-
aligning capability and are free of any influence of mounting error or shaft PERMISSIBLE MISALIGNMENT
deflection. Besides the original type, the E type with pressed cages for high
load capacity is also available. Their bearing numbers are suffixed by E. The permissible misalignment of thrust spherical roller bearings varies
For horizontal shaft or high speed application, machined brass cages are depending on the size, but it is approximately 0.018 to 0.036 radian (1 to
recommended. For details, contact NSK. 2) with average loads.
Since there are several places where lubrication is difficult, such as the area
between the roller heads and inner ring rib, the sliding surfaces between cage
and guide sleeve, etc., oil lubrication should be used even at low speed. MINIMUM AXIAL LOAD
The cages in the original type are machined brass.
It is necessary to apply some axial load to thrust bearings to prevent
TOLERANCES AND RUNNING ACCURACY slippage between the rolling elements and raceways. For more details, please
refer to Page A99.
THRUST BALL BEARINGS Table 8.6 (Pages A72 to A74)
THRUST CYLINDRICAL ROLLER BEARINGS
According to Table 8.2 (Pages A72 to A74)
THRUST SPHERICAL ROLLER BEARINGS Table 8.7 (Pages A75)
RECOMMENDED FITS
THRUST BALL BEARINGS Table 9.3 (Pages A84)
Table 9.5 (Pages A85)
THRUST CYLINDRICAL ROLLER BEARINGS Table 9.3 (Pages A84)
THRUST SPHERICAL ROLLER BEARINGS Table 9.3 (Pages A84)
B 208 B 209
B206-233E.indd 208-209 11/20/13 4:58:19 PM

jd 1 jd a jd a jd a
jd 1
jd A
R
r
ra ra ra
T T3 T4
b
r r ra ra
jD1 jD1 jD2
jD jD jDa jDa jDa
jD3
With Flat Seat With Aligning Seat With Aligning Seat Washer
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers Dimensions Abutment and Fillet Mass (kg)
(mm) (N) {kgf} (min1) (mm) Dimensions (mm) approx.
With With With With With With
d D T T3 T4 r Ca C 0a Ca C 0a Grease Oil Flat Aligning Aligning d1 D1 D2 D3 b A R da Da ra Flat Seat Aligning Aligning
min. Seat Seat Seat Washer min. max. max. Seat Seat Washer
10 24 9 0.3 10 100 14 000 1 030 1 420 6 700 10 000 51100 24 11 18 16 0.3 0.019 . .
26 11 11.6 13 0.6 12 800 17 100 1 300 1 740 6 000 9 000 51200 53200 53200 U 26 12 18 28 3.5 8.5 22 20 16 0.6 0.028 0.029 0.036
12 26 9 0.3 10 400 15 400 1 060 1 570 6 700 10 000 51101 26 13 20 18 0.3 0.021 . .
28 11 11.4 13 0.6 13 300 19 000 1 350 1 940 5 600 8 500 51201 53201 53201 U 28 14 20 30 3.5 11.5 25 22 18 0.6 0.031 0.031 0.039
15 28 9 0.3 10 600 16 800 1 080 1 710 6 300 9 500 51102 28 16 23 20 0.3 0.023 . .
32 12 13.3 15 0.6 16 700 24 800 1 710 2 530 5 000 7 500 51202 53202 53202 U 32 17 24 35 4 12 28 25 22 0.6 0.043 0.048 0.059
17 30 9 0.3 11 400 19 500 1 170 1 990 6 000 9 000 51103 30 18 25 22 0.3 0.025 . .
35 12 13.2 15 0.6 17 300 27 300 1 760 2 780 4 800 7 500 51203 53203 53203 U 35 19 26 38 4 16 32 28 24 0.6 0.050 0.055 0.069
20 35 10 0.3 15 100 26 600 1 540 2 710 5 300 8 000 51104 35 21 29 26 0.3 0.037 . .
40 14 14.7 17 0.6 22 500 37 500 2 290 3 850 4 300 6 300 51204 53204 53204 U 40 22 30 42 5 18 36 32 28 0.6 0.077 0.080 0.096
25 42 11 0.6 19 700 37 000 2 010 3 800 4 800 7 100 51105 42 26 35 32 0.6 0.056 . .
47 15 16.7 19 0.6 28 000 50 500 2 860 5 150 3 800 5 600 51205 53205 53205 U 47 27 36 50 5.5 19 40 38 34 0.6 0.111 0.123 0.151
52 18 19.8 22 1 36 000 61 500 3 650 6 250 3 200 5 000 51305 53305 53305 U 52 27 38 55 6 21 45 41 36 1 0.169 0.182 0.224
60 24 26.4 29 1 56 000 89 500 5 700 9 100 2 600 4 000 51405 53405 53405 U 60 27 42 62 8 19 50 46 39 1 0.334 0.353 0.426
30 47 11 0.6 20 600 42 000 2 100 4 300 4 300 6 700 51106 47 32 40 37 0.6 0.064 . .
52 16 17.8 20 0.6 29 500 58 000 3 000 5 950 3 400 5 300 51206 53206 53206 U 52 32 42 55 5.5 22 45 43 39 0.6 0.137 0.154 0.183
60 21 22.6 25 1 43 000 78 500 4 400 8 000 2 800 4 300 51306 53306 53306 U 60 32 45 62 7 22 50 48 42 1 0.267 0.28 0.336
70 28 30.1 33 1 73 000 126 000 7 450 12 800 2 200 3 400 51406 53406 53406 U 70 32 50 75 9 20 56 54 46 1 0.519 0.535 0.666
35 52 12 0.6 22 100 49 500 2 250 5 050 4 000 6 000 51107 52 37 45 42 0.6 0.081 . .
62 18 19.9 22 1 39 500 78 000 4 050 7 950 3 000 4 500 51207 53207 53207 U 62 37 48 65 7 24 50 51 46 1 0.21 0.231 0.292
68 24 25.6 28 1 56 000 105 000 5 700 10 700 2 400 3 800 51307 53307 53307 U 68 37 52 72 7.5 24 56 55 48 1 0.386 0.403 0.488
80 32 34 37 1.1 87 500 155 000 8 950 15 800 2 000 3 000 51407 53407 53407 U 80 37 58 85 10 23 64 62 53 1 0.769 0.785 0.967
40 60 13 0.6 27 100 63 000 2 770 6 400 3 600 5 300 51108 60 42 52 48 0.6 0.12 . .
68 19 20.3 23 1 47 500 98 500 4 850 10 000 2 800 4 300 51208 53208 53208 U 68 42 55 72 7 28.5 56 57 51 1 0.27 0.289 0.355
78 26 28.5 31 1 70 000 135 000 7 100 13 700 2 200 3 400 51308 53308 53308 U 78 42 60 82 8.5 28 64 63 55 1 0.536 0.581 0.704
90 36 38.2 42 1.1 103 000 188 000 10 500 19 100 1 700 2 600 51408 53408 53408 U 90 42 65 95 12 26 72 70 60 1 1.1 1.12 1.38
45 65 14 0.6 28 100 69 000 2 860 7 050 3 400 5 000 51109 65 47 57 53 0.6 0.143 . .
73 20 21.3 24 1 48 000 105 000 4 900 10 700 2 600 4 000 51209 53209 53209 U 73 47 60 78 7.5 26 56 62 56 1 0.31 0.333 0.419
85 28 30.1 33 1 80 500 163 000 8 200 16 700 2 000 3 000 51309 53309 53309 U 85 47 65 90 10 25 64 69 61 1 0.672 0.702 0.888
100 39 42.4 46 1.1 128 000 246 000 13 000 25 100 1 600 2 400 51409 53409 53409 U 100 47 72 105 12.5 29 80 78 67 1 1.46 1.53 1.87
50 70 14 0.6 29 000 75 500 2 960 7 700 3 200 4 800 51110 70 52 62 58 0.6 0.153 . .
78 22 23.5 26 1 49 000 111 000 5 000 11 400 2 400 3 600 51210 53210 53210 U 78 52 62 82 7.5 32.5 64 67 61 1 0.378 0.404 0.504
95 31 34.3 37 1.1 97 500 202 000 9 950 20 600 1 800 2 800 51310 53310 53310 U 95 52 72 100 11 28 72 77 68 1 0.931 1.01 1.27
110 43 45.6 50 1.5 147 000 288 000 15 000 29 400 1 400 2 200 51410 53410 53410 U 110 52 80 115 14 35 90 86 74 1.5 1.94 1.98 2.41
B 210 B 211
B206-233E.indd 210-211 11/20/13 4:58:20 PM

jd 1 jd a jd a jd a
jd 1
jd A
R
r
ra ra ra
T T3 T4
b
r r ra ra
jD1 jD1 jD2
jD jD jDa jDa jDa
jD3
1
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers( ) Dimensions Abutment and Fillet Mass (kg)
55 78 16 0.6 35 000 93 000 3 600 9 500 2 800 4 300 51111 78 57 69 64 0.6 0.227 . .
90 25 27.3 30 1 70 000 159 000 7 150 16 200 2 200 3 200 51211 53211 53211 U 90 57 72 95 9 35 72 76 69 1 0.599 0.656 0.819
105 35 39.3 42 1.1 115 000 244 000 11 800 24 900 1 600 2 400 51311 53311 53311 U 105 57 80 110 11.5 30 80 85 75 1 1.31 1.45 1.78
120 48 50.5 55 1.5 181 000 350 000 18 500 35 500 1 300 1 900 51411 53411 53411 U 120 57 88 125 15.5 28 90 94 81 1.5 2.58 2.59 3.16
60 85 17 1 41 500 113 000 4 250 11 500 2 600 4 000 51112 85 62 75 70 1 0.281 . .
95 26 28 31 1 71 500 169 000 7 300 17 200 2 000 3 000 51212 53212 53212 U 95 62 78 100 9 32.5 72 81 74 1 0.673 0.731 0.897
110 35 38.3 42 1.1 119 000 263 000 12 100 26 800 1 600 2 400 51312 53312 53312 U 110 62 85 115 11.5 41 90 90 80 1 1.4 1.51 1.83
130 51 54 58 1.5 202 000 395 000 20 600 40 500 1 200 1 800 51412 53412 53412 U 130 62 95 135 16 34 100 102 88 1.5 3.16 3.2 3.91
65 90 18 1 42 000 117 000 4 300 12 000 2 400 3 800 51113 90 67 80 75 1 0.324 . .
100 27 28.7 32 1 75 500 189 000 7 700 19 200 1 900 2 800 51213 53213 53213 U 100 67 82 105 9 40 80 86 79 1 0.756 0.812 0.989
115 36 39.4 43 1.1 123 000 282 000 12 500 28 700 1 500 2 400 51313 53313 53313 U 115 67 90 120 12.5 38.5 90 95 85 1 1.54 1.67 2.04
140 56 60.2 65 2 234 000 495 000 23 800 50 500 1 100 1 700 51413 53413 53413 U 140 68 100 145 17.5 40 112 110 95 2 4.1 4.22 5.13
70 95 18 1 43 500 127 000 4 450 12 900 2 400 3 600 51114 95 72 85 80 1 0.346 . .
105 27 28.8 32 1 74 000 189 000 7 550 19 200 1 900 2 800 51214 53214 53214 U 105 72 88 110 9 38 80 91 84 1 0.793 0.866 1.05
125 40 44.2 48 1.1 137 000 315 000 14 000 32 000 1 400 2 000 51314 53314 53314 U 125 72 98 130 13 43 100 103 92 1 2.0 2.2 2.64
150 60 63.6 69 2 252 000 555 000 25 700 56 500 1 000 1 500 51414 53414 53414 U 150 73 110 155 19.5 34 112 118 102 2 5.05 5.12 6.21
75 100 19 1 43 500 131 000 4 450 13 400 2 200 3 400 51115 100 77 90 85 1 0.389 . .
110 27 28.3 32 1 78 000 209 000 7 950 21 300 1 800 2 800 51215 53215 53215 U 110 77 92 115 9.5 49 90 96 89 1 0.845 1.27 1.11
135 44 48.1 52 1.5 159 000 365 000 16 200 37 500 1 300 1 900 51315 53315 53315 U 135 77 105 140 15 37 100 111 99 1.5 2.6 2.8 3.42
160 65 69 75 2 254 000 560 000 25 900 57 000 950 1 400 51415 53415 53415 U 160 78 115 165 21 42 125 125 110 2 6.15 6.23 7.58
80 105 19 1 45 000 141 000 4 600 14 400 2 200 3 400 51116 105 82 95 90 1 0.417 . .
115 28 29.5 33 1 79 000 218 000 8 050 22 300 1 800 2 600 51216 53216 53216 U 115 82 98 120 10 46 90 101 94 1 0.931 1.01 1.23
140 44 47.6 52 1.5 164 000 395 000 16 700 40 000 1 300 1 900 51316 53316 53316 U 140 82 110 145 15 50 112 116 104 1.5 2.74 2.94 3.55
170 68 72.2 78 2.1 272 000 620 000 27 800 63 500 900 1 300 51416 53416 53416 U 170 83 125 175 22 36 125 133 117 2 7.21 7.33 8.9
85 110 19 1 46 500 150 000 4 700 15 300 2 200 3 200 51117 110 87 100 95 1 0.44 . .
125 31 33.1 37 1 96 000 264 000 9 800 26 900 1 600 2 400 51217 53217 53217 U 125 88 105 130 11 52 100 109 101 1 1.22 1.35 1.63
150 49 53.1 58 1.5 207 000 490 000 21 100 50 000 1 100 1 700 51317 53317 53317 U 150 88 115 155 17.5 43 112 124 111 1.5 3.57 3.78 4.67
180 72 77 83 2.1 310 000 755 000 31 500 77 000 850 1 300 51417 X 53417 X 53417 XU 177 88 130 185 23 47 140 141 124 2 8.51 8.72 10.4
90 120 22 1 60 000 190 000 6 150 19 400 1 900 3 000 51118 120 92 108 102 1 0.646 . .
135 35 38.5 42 1.1 114 000 310 000 11 600 31 500 1 400 2 200 51218 53218 53218 U 135 93 110 140 13.5 45 100 117 108 1 1.69 1.89 2.38
155 50 54.6 59 1.5 214 000 525 000 21 900 53 500 1 100 1 700 51318 53318 53318 U 155 93 120 160 18 40 112 129 116 1.5 3.83 4.11 5.09
190 77 81.2 88 2.1 330 000 825 000 33 500 84 000 800 1 200 51418 X 53418 X 53418 XU 187 93 140 195 25.5 40 140 149 131 2 10.2 10.3 12.4
100 135 25 1 86 000 268 000 8 750 27 300 1 700 2 600 51120 135 102 121 114 1 0.96 . .
150 38 40.9 45 1.1 135 000 375 000 13 700 38 500 1 300 2 000 51220 53220 53220 U 150 103 125 155 14 52 112 130 120 1 2.25 2.49 3.03
170 55 59.2 64 1.5 239 000 595 000 24 300 61 000 1 000 1 500 51320 53320 53320 U 170 103 135 175 18 46 125 142 128 1.5 4.98 5.31 6.37
210 85 90 98 3 370 000 985 000 38 000 100 000 710 1 100 51420 X 53420 X 53420 XU 205 103 155 220 27 50 160 165 145 2.5 14.8 15 18.1
Note (1) The outside diameter d1 of the shaft washers of all bearing numbers marked X is smaller than the outside diameter D
of the housing washers.
B 212 B 213
B206-233E.indd 212-213 11/20/13 4:58:21 PM

jd 1 jd a jd a jd a
jd 1
jd A
R
r
ra ra ra
T T3 T4
b
r r ra ra
jD1 jD1 jD2
jD jD jDa jDa jDa
jD3
1
110 145 25 1 88 000 288 000 8 950 29 400 1 700 2 400 51122 145 112 131 124 1 1.04
160 38 40.2 45 1.1 136 000 395 000 13 900 40 000 1 300 1 900 51222 53222 53222 U 160 113 135 165 14 65 125 140 130 1 2.42 2.65 3.2
190 63 67.2 72 2 282 000 755 000 28 800 77 000 900 1 300 51322 X 53322 X 53322 XU 187 113 150 195 20.5 51 140 158 142 2 7.19 7.55 9.1
230 95 99.7 109 3 415 000 1 150 000 42 000 118 000 630 950 51422 X 53422 X 53422 XU 225 113 170 240 29 59 180 181 159 2.5 20 20.5 24.3
120 155 25 1 90 000 310 000 9 150 31 500 1 600 2 400 51124 155 122 141 134 1 1.12
170 39 40.8 46 1.1 141 000 430 000 14 400 44 000 1 200 1 800 51224 53224 53224 U 170 123 145 175 15 61 125 150 140 1 2.7 2.94 3.58
210 70 74.1 80 2.1 330 000 930 000 33 500 95 000 800 1 200 51324 X 53324 X 53324 XU 205 123 165 220 22 63 160 173 157 2 9.7 10.1 12.4
250 102 107.3 118 4 480 000 1 400 000 49 000 142 000 600 900 51424 X 53424 X 53424 XU 245 123 185 260 32 70 200 196 174 3 26.2 26.5 31.3
130 170 30 1 105 000 350 000 10 700 36 000 1 400 2 000 51126 170 132 154 146 1 1.68
190 45 47.9 53 1.5 183 000 550 000 18 700 56 000 1 100 1 600 51226 X 53226 X 53226 XU 187 133 160 195 17 67 140 166 154 1.5 3.95 4.35 5.33
225 75 80.3 86 2.1 350 000 1 030 000 35 500 105 000 750 1 100 51326 X 53326 X 53326 XU 220 134 177 235 26 53 160 186 169 2 12.1 12.7 15.8
270 110 115.2 128 4 525 000 1 590 000 53 500 162 000 530 800 51426 X 53426 X 53426 XU 265 134 200 280 38 58 200 212 188 3 32.3 32.4 38.8
140 180 31 1 107 000 375 000 11 000 38 500 1 300 2 000 51128 X 178 142 164 156 1 1.83
200 46 48.6 55 1.5 186 000 575 000 18 900 59 000 1 000 1 500 51228 X 53228 X 53228 XU 197 143 170 210 17 87 160 176 164 1.5 4.3 4.74 5.89
240 80 84.9 92 2.1 370 000 1 130 000 37 500 115 000 670 1 000 51328 X 53328 X 53328 XU 235 144 190 250 26 68 180 199 181 2 14.2 16.3 19.5
280 112 117 131 4 550 000 1 750 000 56 500 178 000 530 800 51428 X 53428 X 53428 XU 275 144 206 290 38 83 225 222 198 3 34.7 34.8 41.4
150 190 31 1 110 000 400 000 11 200 41 000 1 300 1 900 51130 X 188 152 174 166 1 1.95
215 50 53.3 60 1.5 238 000 735 000 24 300 75 000 950 1 400 51230 X 53230 X 53230 XU 212 153 180 225 20.5 79 160 189 176 1.5 5.52 6.09 7.82
250 80 83.7 92 2.1 380 000 1 200 000 39 000 123 000 670 1 000 51330 X 53330 X 53330 XU 245 154 200 260 26 89.5 200 209 191 2 15 17.3 20.5
300 120 125.9 140 4 620 000 2 010 000 63 000 205 000 480 710 51430 X 53430 X 53430 XU 295 154 225 310 41 69 225 238 212 3 43.5 43.8 51.9
160 200 31 1 113 000 425 000 11 500 43 500 1 200 1 900 51132 X 198 162 184 176 1 2.07
225 51 54.7 61 1.5 249 000 805 000 25 400 82 000 900 1 400 51232 X 53232 X 53232 XU 222 163 190 235 21 74 160 199 186 1.5 6.04 6.78 8.7
270 87 91.7 100 3 475 000 1 570 000 48 500 160 000 600 900 51332 X 53332 X 53332 XU 265 164 215 280 29 77 200 225 205 2.5 19.6 22.3 26.7
320 130 135.3 150 5 650 000 2 210 000 66 000 226 000 450 670 51432 X 53432 X 53432 XU 315 164 240 330 41.5 84 250 254 226 4 52.7 52.9 62
170 215 34 1.1 135 000 510 000 13 800 52 000 1 100 1 700 51134 X 213 172 197 188 1 2.72
240 55 58.7 65 1.5 280 000 915 000 28 500 93 000 850 1 300 51234 X 53234 X 53234 XU 237 173 200 250 21.5 91 180 212 198 1.5 7.41 8.21 10.5
280 87 91.3 100 3 465 000 1 570 000 47 500 160 000 600 900 51334 X 53334 X 53334 XU 275 174 220 290 29 105 225 235 215 2.5 20.3 23.2 28
340 135 141 156 5 715 000 2 480 000 73 000 253 000 430 630 51434 X 53434 X 53434 XU 335 174 255 350 46 74 250 269 241 4 61.2 61.3 73
180 225 34 1.1 136 000 530 000 13 800 54 000 1 100 1 700 51136 X 222 183 207 198 1 2.79
250 56 58.2 66 1.5 284 000 955 000 28 900 97 000 800 1 200 51236 X 53236 X 53236 XU 247 183 210 260 21.5 112 200 222 208 1.5 7.94 8.57 10.8
300 95 99.3 109 3 480 000 1 680 000 49 000 171 000 560 850 51336 X 53336 X 53336 XU 295 184 240 310 32 91 225 251 229 2.5 25.9 29.2 34.9
360 140 148.3 164 5 750 000 2 730 000 76 500 278 000 400 600 51436 X 53436 X 53436 XU 355 184 270 370 46.5 97 280 285 255 4 70.5 72.1 84.9
190 240 37 1.1 172 000 655 000 17 500 67 000 1 000 1 600 51138 X 237 193 220 210 1 3.6
270 62 65.7 73 2 320 000 1 110 000 32 500 113 000 750 1 100 51238 X 53238 X 53238 XU 267 194 230 280 23 98 200 238 222 2 11.8 12.9 15.7
320 105 111 121 4 550 000 1 960 000 56 000 199 000 500 750 51338 X 53338 X 53338 XU 315 195 255 330 33 104 250 266 244 3 36.5 38.1 44.7
B 214 B 215
B206-233E.indd 214-215 11/20/13 4:58:22 PM

jd 1 jd a jd a jd a
jd 1
jd A
R
r
ra ra ra
T T3 T4
b
r r ra ra
jD1 jD1 jD2
jD jD jDa jDa jDa
jD3
1
200 250 37 1.1 173 000 675 000 17 600 69 000 1 000 1 500 51140 X 247 203 230 220 1 3.75
280 62 65.3 74 2 315 000 1 110 000 32 500 113 000 710 1 100 51240 X 53240 X 53240 XU 277 204 240 290 23 125 225 248 232 2 12.3 13.4 16.1
340 110 118.4 130 4 600 000 2 220 000 61 500 227 000 480 710 51340 X 53340 X 53340 XU 335 205 270 350 38 92 250 282 258 3 43.6 46.2 54.8
220 270 37 1.1 179 000 740 000 18 200 75 500 950 1 500 51144 X 267 223 250 240 1 4.09
300 63 65.6 75 2 325 000 1 210 000 33 500 123 000 670 1 000 51244 X 53244 X 53244 XU 297 224 260 310 25 118 225 268 252 2 13.6 14.9 18
240 300 45 1.5 229 000 935 000 23 400 95 000 850 1 200 51148 X 297 243 276 264 1.5 6.55
340 78 81.6 92 2.1 420 000 1 650 000 43 000 168 000 560 850 51248 X 53248 X 53248 XU 335 244 290 350 30 122 250 299 281 2 23.7 25.6 30.7
260 320 45 1.5 233 000 990 000 23 800 101 000 800 1 200 51152 X 317 263 296 284 1.5 7.01
360 79 82.8 93 2.1 435 000 1 800 000 44 500 184 000 560 850 51252 X 53252 X 53252 XU 355 264 305 370 30 152 280 319 301 2 25.1 27.3 33.2
280 350 53 1.5 315 000 1 310 000 32 000 134 000 710 1 000 51156 X 347 283 322 308 1.5 12
380 80 85 94 2.1 450 000 1 950 000 46 000 199 000 530 800 51256 X 53256 X 53256 XU 375 284 325 390 31 143 280 339 321 2 27.1 30.3 37
300 380 62 2 360 000 1 560 000 36 500 159 000 600 900 51160 X 376 304 348 332 2 17.2
420 95 100.5 112 3 540 000 2 410 000 55 000 246 000 450 670 51260 X 53260 X 53260 XU 415 304 360 430 34 164 320 371 349 2.5 43.5 47.7 56.1
320 400 63 2 365 000 1 660 000 37 500 169 000 600 900 51164 X 396 324 368 352 2 18.6
440 95 100.5 112 3 585 000 2 680 000 59 500 273 000 450 670 51264 X 53264 X 53264 XU 435 325 380 450 36 157 320 391 369 2.5 45 49.9 59.4
340 420 64 2 375 000 1 760 000 38 500 179 000 560 850 51168 X 416 344 388 372 2 19.9
460 96 100.3 113 3 595 000 2 800 000 60 500 285 000 430 630 51268 X 53268 X 53268 XU 455 345 400 470 36 199 360 411 389 2.5 47.9 52.7 62
360 440 65 2 385 000 1 860 000 39 000 190 000 560 800 51172 X 436 364 408 392 2 21.5
500 110 116.7 130 4 705 000 3 500 000 72 000 355 000 380 560 51272 X 53272 X 53272 XU 495 365 430 510 43 172 360 442 418 3 68.8 76.3 90.9
B 216 B 217
B206-233E.indd 216-217 11/20/13 4:58:23 PM

jD
jd jD jD 3
jd jd jd
jd 3 jd 3
R A1
r1 r1 r1 rb
rb rb
T1 B jd 2 T5 T7
T2 T6 T8
r b
r ra ra
jD1 jD1 jD2 jDa
jDa jDa
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers Dimensions Abutment and Fillet Mass (kg)
d2 d D T1 T5 T7 r r1 Ca C 0a Ca C 0a Grease Oil Flat Seat Aligning Aligning d3 D1 D2 D3 T2 T6 T8 B b A1 R Da ra rb Flat Seat Aligning Aligning
min. min. Seat Seat Washer max. max. max. Seat Seat Washer
10 15 32 22 24.6 28 0.6 0.3 16 700 24 800 1 710 2 530 4 800 7 100 52202 54202 54202 U 32 17 24 35 13.5 14.8 16.5 5 4 10.5 28 24 0.6 0.3 0.081 0.090 0.113
15 20 40 26 27.4 32 0.6 0.3 22 500 37 500 2 290 3 850 4 000 6 000 52204 54204 54204 U 40 22 30 42 16 16.7 19 6 5 16 36 30 0.6 0.3 0.148 0.151 0.185
25 60 45 49.8 55 1 0.6 56 000 89 500 5 700 9 100 2 400 3 600 52405 54405 54405 U 60 27 42 62 28 30.4 33 11 8 15 50 42 1 0.6 0.641 0.68 0.825
20 25 47 28 31.4 36 0.6 0.3 28 000 50 500 2 860 5 150 3 400 5 300 52205 54205 54205 U 47 27 36 50 17.5 19.2 21.5 7 5.5 16.5 40 36 0.6 0.3 0.213 0.236 0.293
25 52 34 37.6 42 1 0.3 36 000 61 500 3 650 6 250 3 000 4 500 52305 54305 54305 U 52 27 38 55 21 22.8 25 8 6 18 45 38 1 0.3 0.324 0.35 0.434
30 70 52 56.2 62 1 0.6 73 000 126 000 7 450 12 800 2 200 3 200 52406 54406 54406 U 70 32 50 75 32 34.1 37 12 9 16 56 50 1 0.6 0.978 1.01 1.27
25 30 52 29 32.6 37 0.6 0.3 29 500 58 000 3 000 5 950 3 200 5 000 52206 54206 54206 U 52 32 42 55 18 19.8 22 7 5.5 20 45 42 0.6 0.3 0.254 0.288 0.345
30 60 38 41.2 46 1 0.3 43 000 78 500 4 400 8 000 2 600 4 000 52306 54306 54306 U 60 32 45 62 23.5 25.1 27.5 9 7 19.5 50 45 1 0.3 0.483 0.511 0.621
35 80 59 63 69 1.1 0.6 87 500 155 000 8 950 15 800 1 800 2 800 52407 54407 54407 U 80 37 58 85 36.5 38.5 41.5 14 10 18.5 64 58 1 0.6 1.43 1.47 1.83
30 35 62 34 37.8 42 1 0.3 39 500 78 000 4 050 7 950 2 800 4 300 52207 54207 54207 U 62 37 48 65 21 22.9 25 8 7 21 50 48 1 0.3 0.406 0.447 0.57
35 68 44 47.2 52 1 0.3 56 000 105 000 5 700 10 700 2 400 3 600 52307 54307 54307 U 68 37 52 72 27 28.6 31 10 7.5 21 56 52 1 0.3 0.71 0.744 0.915
40 68 36 38.6 44 1 0.6 47 500 98 500 4 850 10 000 2 600 3 800 52208 54208 54208 U 68 42 55 72 22.5 23.8 26.5 9 7 25 56 55 1 0.6 0.543 0.581 0.713
40 78 49 54 59 1 0.6 70 000 135 000 7 100 13 700 2 000 3 000 52308 54308 54308 U 78 42 60 82 30.5 33 35.5 12 8.5 23.5 64 60 1 0.6 1.04 1.13 1.38
40 90 65 69.4 77 1.1 0.6 103 000 188 000 10 500 19 100 1 700 2 400 52408 54408 54408 U 90 42 65 95 40 42.2 46 15 12 22 72 65 1 0.6 1.98 2.02 2.54
35 45 73 37 39.6 45 1 0.6 48 000 105 000 4 900 10 700 2 400 3 600 52209 54209 54209 U 73 47 60 78 23 24.3 27 9 7.5 23 56 60 1 0.6 0.606 0.652 0.823
45 85 52 56.2 62 1 0.6 80 500 163 000 8 200 16 700 1 900 2 800 52309 54309 54309 U 85 47 65 90 32 34.1 37 12 10 21 64 65 1 0.6 1.28 1.34 1.71
45 100 72 78.8 86 1.1 0.6 128 000 246 000 13 000 25 100 1 500 2 200 52409 54409 54409 U 100 47 72 105 44.5 47.9 51.5 17 12.5 23.5 80 72 1 0.6 2.71 2.85 3.53
40 50 78 39 42 47 1 0.6 49 000 111 000 5 000 11 400 2 400 3 400 52210 54210 54210 U 78 52 62 82 24 25.5 28 9 7.5 30.5 64 62 1 0.6 0.697 0.75 0.949
50 95 58 64.6 70 1.1 0.6 97 500 202 000 9 950 20 600 1 700 2 600 52310 54310 54310 U 95 52 72 100 36 39.3 42 14 11 23 72 72 1 0.6 1.78 1.94 2.46
50 110 78 83.2 92 1.5 0.6 147 000 288 000 15 000 29 400 1 400 2 000 52410 54410 54410 U 110 52 80 115 48 50.6 55 18 14 30 90 80 1.5 0.6 3.51 3.59 4.45
45 55 90 45 49.6 55 1 0.6 70 000 159 000 7 150 16 200 2 000 3 000 52211 54211 54211 U 90 57 72 95 27.5 29.8 32.5 10 9 32.5 72 72 1 0.6 1.11 1.22 1.55
55 105 64 72.6 78 1.1 0.6 115 000 244 000 11 800 24 900 1 500 2 400 52311 54311 54311 U 105 57 80 110 39.5 43.8 46.5 15 11.5 25.5 80 80 1 0.6 2.43 2.7 3.35
55 120 87 92 101 1.5 0.6 181 000 350 000 18 500 35 500 1 200 1 800 52411 54411 54411 U 120 57 88 125 53.5 56 60.5 20 15.5 22.5 90 88 1.5 0.6 4.66 4.68 5.82
50 60 95 46 50 56 1 0.6 71 500 169 000 7 300 17 200 1 900 3 000 52212 54212 54212 U 95 62 78 100 28 30 33 10 9 30.5 72 78 1 0.6 1.22 1.33 1.66
60 110 64 70.6 78 1.1 0.6 119 000 263 000 12 100 26 800 1 500 2 200 52312 54312 54312 U 110 62 85 115 39.5 42.8 46.5 15 11.5 36.5 90 85 1 0.6 2.59 2.82 3.45
60 130 93 99 107 1.5 0.6 202 000 395 000 20 600 40 500 1 100 1 700 52412 54412 54412 U 130 62 95 135 57 60 64 21 16 28 100 95 1.5 0.6 5.74 5.82 7.24
65 140 101 109.4 119 2 1 234 000 495 000 23 800 50 500 1 000 1 600 52413 54413 54413 U 140 68 100 145 62 66.2 71 23 17.5 34 112 100 2 1 7.41 7.66 9.47
55 65 100 47 50.4 57 1 0.6 75 500 189 000 7 700 19 200 1 900 2 800 52213 54213 54213 U 100 67 82 105 28.5 30.2 33.5 10 9 38.5 80 82 1 0.6 1.34 1.45 1.81
65 115 65 71.8 79 1.1 0.6 123 000 282 000 12 500 28 700 1 500 2 200 52313 54313 54313 U 115 67 90 120 40 43.4 47 15 12.5 34.5 90 90 1 0.6 2.8 3.06 3.8
70 105 47 50.6 57 1 1 74 000 189 000 7 550 19 200 1 800 2 800 52214 54214 54214 U 105 72 88 110 28.5 30.3 33.5 10 9 36.5 80 88 1 1 1.44 1.59 1.95
70 125 72 80.4 88 1.1 1 137 000 315 000 14 000 32 000 1 300 2 000 52314 54314 54314 U 125 72 98 130 44 48.2 52 16 13 39 100 98 1 1 3.67 4.07 4.95
70 150 107 114.2 125 2 1 252 000 555 000 25 700 56 500 1 000 1 500 52414 54414 54414 U 150 73 110 155 65.5 69.1 74.5 24 19.5 28.5 112 110 2 1 8.99 9.12 11.3
B 218 B 219
B206-233E.indd 218-219 11/20/13 4:58:24 PM

jD
jd jD jD 3
jd jd jd
jd 3 jd 3
R A1
r1 r1 r1 rb
rb rb
T1 B jd 2 T5 T7
T2 T6 T8
r b
r ra ra
jD1 jD1 jD2 jDa
jDa jDa
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers( 1) Dimensions Abutment and Fillet Mass (kg)
60 75 110 47 49.6 57 1 1 78 000 209 000 7 950 21 300 1 800 2 600 52215 54215 54215 U 110 77 92 115 28.5 29.8 33.5 10 9.5 47.5 90 92 1 1 1.54 1.66 2.06
75 135 79 87.2 95 1.5 1 159 000 365 000 16 200 37 500 1 200 1 800 52315 54315 54315 U 135 77 105 140 48.5 52.6 56.5 18 15 32.5 100 105 1.5 1 4.74 5.14 6.38
75 160 115 123 135 2 1 254 000 560 000 25 900 57 000 900 1 400 52415 54415 54415 U 160 78 115 165 70.5 74.5 80.5 26 21 36.5 125 115 2 1 10.8 11 13.7
65 80 115 48 51 58 1 1 79 000 218 000 8 050 22 300 1 700 2 600 52216 54216 54216 U 115 82 98 120 29 30.5 34 10 10 45 90 98 1 1 1.66 1.78 2.21
80 140 79 86.2 95 1.5 1 164 000 395 000 16 700 40 000 1 200 1 800 52316 54316 54316 U 140 82 110 145 48.5 52.1 56.5 18 15 45.5 112 110 1.5 1 4.99 5.39 6.61
80 170 120 128.4 140 2.1 1 272 000 620 000 27 800 63 500 850 1 300 52416 54416 54416 U 170 83 125 175 73.5 77.7 83.5 27 22 30.5 125 125 2 1 12.6 12.8 16
85 180 128 138 150 2.1 1.1 310 000 755 000 31 500 77 000 800 1 200 52417 X 54417 X 54417 XU 179.5 88 130 185 78.5 83.5 89.5 29 23 40.5 140 130 2 1 15.4 15.8 19.5
70 85 125 55 59.2 67 1 1 96 000 264 000 9 800 26 900 1 500 2 200 52217 54217 54217 U 125 88 105 130 33.5 35.6 39.5 12 11 49.5 100 105 1 1 2.26 2.45 3.02
85 150 87 95.2 105 1.5 1 207 000 490 000 21 100 50 000 1 100 1 600 52317 54317 54317 U 150 88 115 155 53 57.1 62 19 17.5 39 112 115 1.5 1 6.38 6.8 10.5
90 190 135 143.4 157 2.1 1.1 330 000 825 000 33 500 84 000 750 1 100 52418 X 54418 X 54418 XU 189.5 93 140 195 82.5 86.7 93.5 30 25.5 34.5 140 140 2 1 17.5 18.1 22.5
75 90 135 62 69 76 1.1 1 114 000 310 000 11 600 31 500 1 400 2 000 52218 54218 54218 U 135 93 110 140 38 41.5 45 14 13.5 42 100 110 1 1 3.09 3.42 4.39
90 155 88 97.2 106 1.5 1 214 000 525 000 21 900 53 500 1 100 1 600 52318 54318 54318 U 155 93 120 160 53.5 58.1 62.5 19 18 36.5 112 120 1.5 1 6.79 7.33 9.29
80 100 210 150 160 176 3 1.1 370 000 985 000 38 000 100 000 670 1 000 52420 X 54420 X 54420 XU 209.5 103 155 220 91.5 96.5 104.5 33 27 43.5 160 155 2.5 1 26.8 27.2 33.4
85 100 150 67 72.8 81 1.1 1 135 000 375 000 13 700 38 500 1 300 1 900 52220 54220 54220 U 150 103 125 155 41 43.9 48 15 14 49 112 125 1 1 4.08 4.54 5.64
100 170 97 105.4 115 1.5 1 239 000 595 000 24 300 61 000 950 1 500 52320 54320 54320 U 170 103 135 175 59 63.2 68 21 18 42 125 135 1.5 1 8.82 9.47 11.6
90 110 230 166 3 1.1 415 000 1 150 000 42 000 118 000 600 900 52422 X 229 113 101.5 37 159 2.5 1 35.6
95 110 160 67 71.4 81 1.1 1 136 000 395 000 13 900 40 000 1 200 1 800 52222 54222 54222 U 160 113 135 165 41 43.2 48 15 14 62 125 135 1 1 4.39 4.83 5.94
110 190 110 118.4 128 2 1 282 000 755 000 28 800 77 000 850 1 300 52322 X 54322 X 54322 XU 189.5 113 150 195 67 71.2 76 24 20.5 47 140 150 2 1 12.7 13.5 16.6
120 250 177 4 1.5 515 000 1 540 000 52 500 157 000 560 850 52424 X 249 123 108.5 40 174 3 1.5 47.6
100 120 170 68 71.6 82 1.1 1.1 141 000 430 000 14 400 44 000 1 200 1 800 52224 54224 54224 U 170 123 145 175 41.5 43.3 48.5 15 15 58.5 125 145 1 1 4.92 5.4 6.68
120 210 123 131.2 143 2.1 1.1 330 000 930 000 33 500 95 000 750 1 100 52324 X 54324 X 54324 XU 209.5 123 165 220 75 79.1 85 27 22 58 160 165 2 1 17.6 16.4 22.9
130 270 192 4 1.5 525 000 1 590 000 53 500 162 000 530 800 52426 X 269 134 117 42 188 3 1.5 57.8
110 130 190 80 85.8 96 1.5 1.1 183 000 550 000 18 700 56 000 1 000 1 500 52226 X 54226 X 54226 XU 189.5 133 160 195 49 51.9 57 18 17 63 140 160 1.5 1 7.43 8.24 10.2
130 225 130 2.1 1.1 350 000 1 030 000 35 500 105 000 710 1 100 52326 X 224 134 80 30 169 2 1 21.5
140 280 196 4 1.5 550 000 1 750 000 56 500 178 000 500 750 52428 X 279 144 120 44 198 3 1.5 62.4
120 140 200 81 86.2 99 1.5 1.1 186 000 575 000 18 900 59 000 1 000 1 500 52228 X 54228 X 54228 XU 199.5 143 170 210 49.5 52.1 58.5 18 17 83.5 160 170 1.5 1 8.01 8.87 11.2
140 240 140 2.1 1.1 370 000 1 130 000 37 500 115 000 670 1 000 52328 X 239 144 85.5 31 181 2 1 24.8
150 300 209 4 2 620 000 2 010 000 63 000 205 000 480 710 52430 X 299 153 127.5 46 212 3 2 77.8
130 150 215 89 95.6 109 1.5 1.1 238 000 735 000 24 300 75 000 900 1 300 52230 X 54230 X 54230 XU 214.5 153 180 225 54.5 57.8 64.5 20 20.5 74.5 160 180 1.5 1 10.4 11.5 15
150 250 140 2.1 1.1 380 000 1 200 000 39 000 123 000 630 950 52330 X 249 154 85.5 31 191 2 1 30.3
160 320 226 5 2 650 000 2 210 000 66 000 226 000 430 630 52432 X 319 164 138 50 226 4 2 93.6
Note (1) The outside diameter d3 of the central washers of all bearing numbers marked X is smaller than the outside diameter
D of the housing washers.
B 220 B 221
B206-233E.indd 220-221 11/20/13 4:58:25 PM

jD
jd jD jD 3
jd jd jd
jd 3 jd 3
R A1
r1 r1 r1 rb
rb rb
T1 B jd 2 T5 T7
T2 T6 T8
r b
r ra ra
jD1 jD1 jD2 jDa
jDa jDa
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers( 1) Dimensions Abutment and Fillet Mass (kg)
135 170 340 236 5 2.1 715 000 2 480 000 73 000 253 000 400 600 52434 X 339 174 143 50 240 4 2 110
140 160 225 90 97.4 110 1.5 1.1 249 000 805 000 25 400 82 000 850 1 300 52232 X 54232 X 54232 XU 224.5 163 190 235 55 58.7 65 20 21 70 160 190 1.5 1 11.2 12.7 16.5
160 270 153 3 1.1 475 000 1 570 000 48 500 160 000 600 900 52332 X 269 164 93 33 205 2.5 1 35.1
180 360 245 5 3 750 000 2 730 000 76 500 278 000 380 560 52436 X 359 184 148.5 52 254 4 2.5 126
150 170 240 97 104.4 117 1.5 1.1 280 000 915 000 28 500 93 000 800 1 200 52234 X 54234 X 54234 XU 239.5 173 200 250 59 62.7 69 21 21.5 87 180 200 1.5 1 13.6 15.2 19.8
170 280 153 3 1.1 465 000 1 570 000 47 500 160 000 560 850 52334 X 279 174 93 33 215 2.5 1 40.8
180 250 98 102.4 118 1.5 2 284 000 955 000 28 900 97 000 800 1 200 52236 X 54236 X 54236 XU 249 183 210 260 59.5 61.7 69.5 21 21.5 108.5 200 210 1.5 2 14.8 16.1 20.6
180 300 165 3 2 480 000 1 680 000 49 000 171 000 530 800 52336 X 299 184 101 37 229 2.5 2.5 46.3
160 190 270 109 116.4 131 2 2 320 000 1 110 000 32 500 113 000 710 1 100 52238 X 54238 X 54238 XU 269 194 230 280 66.5 70.2 77.5 24 23 93.5 200 230 2 2 22.1 22.2 29.8
190 320 183 4 2 550 000 1 960 000 56 000 199 000 480 710 52338 X 319 195 111.5 40 244 3 2 113
170 200 280 109 115.6 133 2 2 315 000 1 110 000 32 500 113 000 710 1 000 52240 X 54240 X 54240 XU 279 204 240 290 66.5 69.8 78.5 24 23 120.5 225 240 2 2 23.1 23.2 30.6
200 340 192 4 2 600 000 2 220 000 61 500 227 000 450 670 52340 X 339 205 117 42 258 3 2 78.4
190 220 300 110 115.2 134 2 2 325 000 1 210 000 33 500 123 000 670 1 000 52244 X 54244 X 54244 XU 299 224 260 310 67 69.6 79 24 25 114 225 260 2 2 25.2 27.8 34.1
Note (1) The outside diameter d3 of the central washers of all bearing numbers marked X is smaller than the outside diameter
D of the housing washers.
B 222 B 223
B206-233E.indd 222-223 11/20/13 4:58:26 PM

jd 1
jd a
jd
t
r ra
Dw T
r t ra
jD1
jD jDa
Boundary Dimensions Limiting Speeds Abutment and Fillet Mass

Basic Load Ratings Dimensions
(mm) (min1) Dimensions (mm) (kg)
(N) (mm)
Bearing Numbers
d D T r Ca C 0a
Grease Oil
d1 D1 Dw t da Da ra
35 80 32 1.1 95 500 247 000 1 000 3 000 35 TMP 14 80 37 12 10 71 46 1 0.97

40 78 22 1 63 000 194 000 1 200 3 600 40 TMP 93 78 42 8 7 71 48 1 0.525
45 65 14 0.6 33 000 100 000 1 700 5 000 45 TMP 11 65 47 6 4 60 49 0.6 0.144
85 24 1 71 000 233 000 1 100 3 400 45 TMP 93 85 47 8 8 78 53 1 0.665
50 110 27 1.1 139 000 470 000 900 2 800 50 TMP 74 109 52 11 8 100 61 1 1.52
95 27 1.1 113 000 350 000 1 000 3 000 50 TMP 93 93 52 11 8 89 57 1 0.94
55 105 30 1.1 134 000 450 000 900 2 600 55 TMP 93 105 55.2 11 9.5 98 63 1 1.28
60 95 26 1 99 000 325 000 1 000 3 000 60 TMP 12 95 62 10 8 88 67 1 0.735
110 30 1.1 139 000 480 000 850 2 600 60 TMP 93 110 62 11 9.5 103 68 1 1.36
65 100 27 1 110 000 325 000 950 2 800 65 TMP 12 100 67 12.5 7.25 93 71 1 0.805
115 30 1.1 145 000 515 000 850 2 600 65 TMP 93 115 65.2 11 9.5 108 73 1 1.44
70 150 36 2 259 000 935 000 670 2 000 70 TMP 74 149 72 15 10.5 137 84 2 3.8
125 34 1.1 191 000 635 000 750 2 200 70 TMP 93 125 72 14 10 117 78 1 1.95
75 100 19 1 63 500 221 000 1 100 3 400 75 TMP 11 100 77 8 5.5 96 79 1 0.41
135 36 1.5 209 000 735 000 710 2 200 75 TMP 93 135 77 14 11 125 84 1.5 2.42
80 115 28 1 120 000 420 000 900 2 600 80 TMP 12 115 82 11 8.5 109 86 1 1.02
140 36 1.5 208 000 740 000 710 2 000 80 TMP 93 138 82 14 11 130 91 1.5 2.54
85 110 19 1 75 000 298 000 1 100 3 200 85 TMP 11 110 87 7.5 5.75 105 89 1 0.46
125 31 1 151 000 485 000 800 2 400 85 TMP 12 125 88 14 8.5 118 92 1 1.36
150 39 1.5 257 000 995 000 630 1 900 85 TMP 93 148 87 14 12.5 140 95 1.5 3.2
90 120 22 1 96 000 370 000 950 3 000 90 TMP 11 119 91.5 9 6.5 114 95 1 0.725
155 39 1.5 250 000 885 000 630 1 900 90 TMP 93 155 90.2 16 11.5 144 101 1.5 3.3
100 170 42 1.5 292 000 1 110 000 560 1 700 100 TMP 93 170 103 16 13 159 110 1.5 4.25
110 160 38 1.1 228 000 855 000 630 1 900 110 TMP 12 160 113 15 11.5 150 119 1 2.66
190 48 2 390 000 1 490 000 500 1 500 110 TMP 93 190 113 19 14.5 179 120 2 6.15
120 170 39 1.1 233 000 895 000 600 1 800 120 TMP 12 170 123 15 12 160 129 1 2.93
210 54 2.1 505 000 1 930 000 450 1 400 120 TMP 93 210 123 22 16 199 129 2 8.55
130 190 45 1.5 300 000 1 090 000 530 1 600 130 TMP 12 187 133 19 13 177 142 1.5 4.5
225 58 2.1 585 000 2 370 000 430 1 300 130 TMP 93 225 133 22 18 214 140 2 10.4
270 85 4 895 000 3 300 000 320 950 130 TMP 94 270 133 32 26.5 254 150 3 26.2
Remarks For cylindrical roller thrust bearings not listed adove, please contact NSK.
B 224 B 225
B206-233E.indd 224-225 11/20/13 4:58:27 PM

jd 1
jd a
jd
t
r ra
Dw T
r t ra
jD1
jD jDa
Boundary Dimensions Limiting Speeds Abutment and Fillet Mass

Basic Load Ratings Dimensions
(mm) (min1) Dimensions (mm) (kg)
(N) (mm)
Bearing Numbers
d D T r Ca C 0a
Grease Oil
d1 D1 Dw t da Da ra
140 200 46 2 285 000 1 120 000 500 1 500 140 TMP 12 197 143 17 14.5 188 153 2 4.85
240 60 2.1 610 000 2 360 000 400 1 200 140 TMP 93 240 143 25 17.5 226 154 2 12.2
280 85 4 990 000 3 800 000 300 900 140 TMP 94 280 143 32 26.5 262 158 3 27.5
150 215 50 2 375 000 1 500 000 480 1 400 150 TMP 12 215 153 19 15.5 202 163 2 6.15
250 60 2.1 635 000 2 510 000 400 1 200 150 TMP 93 250 153 25 17.5 236 165 2 12.8
160 200 31 1 173 000 815 000 630 1 900 160 TMP 11 200 162 11 10 191 168 1 2.21
270 67 3 745 000 3 150 000 360 1 100 160 TMP 93 265 164 25 21 255 173 2.5 16.9
170 240 55 1.5 485 000 1 960 000 430 1 300 170 TMP 12 237 173 22 16.5 227 182 1.5 8.2
280 67 3 800 000 3 500 000 340 1 000 170 TMP 93 280 173 25 21 265 183 2.5 17.7
180 300 73 3 1 000 000 4 000 000 320 950 180 TMP 93 300 185 32 20.5 284 194 2.5 22.5
360 109 5 1 640 000 6 200 000 240 710 180 TMP 94 354 189 45 32 335 205 4 58.2
190 270 62 3 705 000 2 630 000 360 1 100 190 TMP 12 266 195 30 16 255 200 2.5 11.8
320 78 4 1 080 000 4 500 000 300 900 190 TMP 93 320 195 32 23 303 205 3 27.6
200 250 37 1.1 365 000 1 690 000 500 1 500 200 TMP 11 247 203 17 10 242 207 1 4.1
340 85 4 1 180 000 5 150 000 280 800 200 TMP 93 340 205 32 26.5 322 218 3 34.5
220 270 37 1.1 385 000 1 860 000 480 1 500 220 TMP 11 267 223 17 10 262 227 1 4.5
300 63 2 770 000 3 100 000 340 1 000 220 TMP 12 297 224 30 16.5 287 232 2 13.5
240 300 45 1.5 435 000 2 160 000 400 1 200 240 TMP 11 297 243 18 13.5 288 251 1.5 7.2
340 78 2.1 965 000 4 100 000 280 850 240 TMP 12 335 244 32 23 322 258 2 23.3
260 320 45 1.5 460 000 2 350 000 400 1 200 260 TMP 11 317 263 18 13.5 308 272 1.5 7.75
360 79 2.1 995 000 4 350 000 280 850 260 TMP 12 355 264 32 23.5 342 276 2 25.2
280 350 53 1.5 545 000 2 800 000 340 1 000 280 TMP 11 347 283 20 16.5 335 294 1.5 11.6
380 80 2.1 1 050 000 4 750 000 260 800 280 TMP 12 375 284 32 24 362 296 2 27.2
300 380 62 2 795 000 4 000 000 300 900 300 TMP 11 376 304 25 18.5 365 315 2 16.7
420 95 3 1 390 000 6 250 000 220 670 300 TMP 12 415 304 38 28.5 398 322 2.5 42
320 400 63 2 820 000 4 250 000 300 900 320 TMP 11 396 324 25 19 385 335 2 18
440 95 3 1 420 000 6 550 000 220 670 320 TMP 12 435 325 38 28.5 418 340 2.5 44.5
Remarks For cylindrical roller thrust bearings not listed adove, please contact NSK.
B 226 B 227
B206-233E.indd 226-227 11/20/13 4:58:27 PM

THRUST SPHERICAL ROLLER BEARINGS
jD b
jd 1
jd 1 jd a
A jd A
jd Dynamic Equivalent Load
r r ra jd S1 P = 1.2Fr +Fa
B1 30
B B2 T B2 Static Equivalent Load
T
C C P0 = 2.8Fr +Fa
r r ra
jD1 However, Fr /Fa0.55 must be
jD1
jD jDa satisfied.
jD jd S2
Boundary Dimensions Basic Load Ratings Limiting Dimensions Spacer Sleeve Abutment and Fillet Mass
(mm) (N) {kgf} Speeds (mm) Dimensions (mm) Dimensions (mm) (kg)
Bearing
(min1) Numbers
d D T r Ca C 0a Ca C 0a Oil d1 D1 B,B 1 B2 C A d S1 d S2 da(1) Da Db ra
min. max. max. min. max. min. max. approx.
60 130 42 1.5 330 000 885 000 33 500 90 000 2 600 29412 E 114.5 89 27 38 20 38 67 67 90 108 133 1.5 2.55
65 140 45 2 405 000 1 100 000 41 500 112 000 2 400 29413 E 121.5 93 29.5 40.5 22 42 72 72 100 115 143 2 3.2
70 150 48 2 450 000 1 240 000 46 000 126 000 2 400 29414 E 131.5 102 31 43 24 44 78 78 105 125 153 2 3.9
75 160 51 2 515 000 1 430 000 52 500 146 000 2 200 29415 E 138 107 33.5 46 25 47 83 83 115 132 163 2 4.65
80 170 54 2.1 575 000 1 600 000 58 500 163 000 2 000 29416 E 148 114.5 35 48.5 27 50 89 89 120 140 173 2 5.55
85 150 39 1.5 330 000 1 040 000 34 000 106 000 2 400 29317 E 134.5 112 24.5 35.5 19 50 91 91 115 135 153 1.5 2.7
180 58 2.1 630 000 1 760 000 64 500 179 000 1 900 29417 E 156.5 124 37 51.5 28 54 95 95 130 150 183 2 6.55
90 155 39 1.5 350 000 1 080 000 35 500 110 000 2 200 29318 E 139.5 118 24.5 35 19 52 97 97 120 140 158 1.5 2.83
190 60 2.1 695 000 1 950 000 70 500 199 000 1 800 29418 E 165.5 129.5 39 54.5 29 56 100 100 135 157 193 2 7.55
100 170 42 1.5 410 000 1 280 000 41 500 131 000 2 000 29320 E 152 128 26.2 38 20.8 58 107 107 130 150 173 1.5 3.6
210 67 3 840 000 2 400 000 86 000 245 000 1 600 29420 E 185 144 43 59.5 33 62 111 111 150 175 214 2.5 10.3
110 190 48 2 530 000 1 710 000 54 000 174 000 1 800 29322 E 169.5 142.5 30.3 43.5 24 64 117 117 145 165 193 2 5.25
230 73 3 1 010 000 2 930 000 103 000 299 000 1 500 29422 E 200 157 47 64.5 36 69 121 129 165 190 234 2.5 13.3
120 210 54 2.1 645 000 2 100 000 65 500 214 000 1 600 29324 E 187.5 156.5 34 48.5 27 70 130 130 160 180 214 2 7.3
250 78 4 1 160 000 3 400 000 119 000 350 000 1 400 29424 E 215 171 50.5 69.5 38 74 132 142 180 205 254 3 16.6
130 225 58 2.1 740 000 2 450 000 75 500 250 000 1 500 29326 E 203.5 168.5 37 53.5 28 76 141 143 170 195 229 2 8.95
270 85 4 1 330 000 3 900 000 135 000 400 000 1 200 29426 E 235 185 54 74.5 42 81 143 153 195 225 275 3 21.1
140 240 60 2.1 840 000 2 810 000 85 500 287 000 1 400 29328 E 216.5 179 38.5 54 30 82 148 154 185 205 244 2 10.4
280 85 4 1 370 000 4 200 000 140 000 425 000 1 200 29428 E 244.5 195.5 54 74.5 42 86 153 162 205 235 285 3 22.2
150 250 60 2.1 870 000 2 900 000 89 000 296 000 1 400 29330 E 224 190 38 54.5 29 87 158 163 195 215 254 2 10.8
300 90 4 1 580 000 4 900 000 162 000 500 000 1 100 29430 E 266 209 58 81 44 92 164 175 220 250 306 3 27.3
160 270 67 3 1 010 000 3 400 000 103 000 345 000 1 300 29332 E 243 203 42 60 33 92 169 176 210 235 275 2.5 14.3
320 95 5 1 740 000 5 400 000 178 000 550 000 1 100 29432 E 278 224.5 60.5 84.5 46 99 175 189 230 265 326 4 32.1
170 280 67 3 1 050 000 3 500 000 107 000 355 000 1 200 29334 E 252 214.5 42.2 60.5 32 96 178 188 220 245 285 2.5 14.8
340 103 5 1 680 000 5 800 000 171 000 595 000 1 000 29434 310 243 37 99 50 104 245 285 4 43.5
180 300 73 3 1 230 000 4 200 000 125 000 430 000 1 100 29336 E 270 227 46 65.5 36 103 189 195 235 260 306 2.5 19
360 109 5 1 870 000 6 500 000 190 000 660 000 900 29436 330 255 39 105 52 110 260 300 4 52
190 320 78 4 1 370 000 4 700 000 140 000 480 000 1 100 29338 E 288.5 244 49 69 38 110 200 211 250 275 326 3 23
380 115 5 2 100 000 7 450 000 215 000 760 000 850 29438 345 271 41 111 55 117 275 320 4 60
200 280 48 2 540 000 2 310 000 55 000 236 000 1 500 29240 266 236 15 46 24 108 235 255 2 8.55
340 85 4 1 570 000 5 450 000 160 000 555 000 1 000 29340 E 306.5 257 53.5 75 41 116 211 224 265 295 346 3 28.5
400 122 5 2 290 000 8 150 000 234 000 835 000 800 29440 365 280 43 117 59 122 290 335 4 69
Note (1) For heavy load applications, a da value should be chosen which is large enough to support the shaft washer rib.
B 228 B 229
B206-233E.indd 228-229 11/20/13 4:58:28 PM

jd 1 jd a
jd A Dynamic Equivalent Load
ra
r P = 1.2Fr +Fa
B1 Static Equivalent Load
B2 T
C P0 = 2.8Fr +Fa
r ra
However, Fr /Fa0.55 must be
jD1
satisfied.
jD jDa
Boundary Dimensions Basic Load Ratings Limiting Dimensions Abutment and Fillet Mass
(mm) (N) {kgf} Speeds (mm) Dimensions (mm) (kg)
Bearing
(min1) Numbers
d D T r Ca C 0a Ca C 0a Oil d1 D1 B1 B2 C A da(1) Da ra
220 300 48 2 560 000 2 500 000 57 000 255 000 1 400 29244 285 254 15 46 24 117 260 275 2 9.2
360 85 4 1 340 000 5 200 000 137 000 530 000 950 29344 335 280 29 81 41 125 285 315 3 33
420 122 6 2 350 000 8 650 000 240 000 880 000 800 29444 385 308 43 117 58 132 310 355 5 74
240 340 60 2.1 800 000 3 450 000 82 000 350 000 1 200 29248 325 283 19 57 30 130 285 305 2 16.5
380 85 4 1 360 000 5 400 000 139 000 550 000 950 29348 355 300 29 81 41 135 300 330 3 35.5
440 122 6 2 420 000 9 100 000 247 000 930 000 750 29448 405 326 43 117 59 142 330 375 5 79
260 360 60 2.1 855 000 3 850 000 87 500 395 000 1 200 29252 345 302 19 57 30 139 305 325 2 18
420 95 5 1 700 000 6 800 000 173 000 695 000 800 29352 390 329 32 91 45 148 330 365 4 48.5
480 132 6 2 820 000 10 700 000 287 000 1 090 000 710 29452 445 357 48 127 64 154 360 405 5 105
280 380 60 2.1 885 000 4 100 000 90 000 420 000 1 100 29256 365 323 19 57 30 150 325 345 2 19
440 95 5 1 830 000 7 650 000 187 000 780 000 800 29356 410 348 32 91 46 158 350 390 4 52.5
520 145 6 3 400 000 13 100 000 345 000 1 330 000 630 29456 480 384 52 140 68 166 390 440 5 132
520 145 6 3 950 000 14 900 000 400 000 1 520 000 630 29456 EM 480 380 52 140 70 166 410 445 5 134
300 420 73 3 1 160 000 5 150 000 118 000 525 000 950 29260 400 353 21 69 38 162 355 380 2.5 30
480 109 5 2 190 000 9 100 000 224 000 925 000 710 29360 450 379 37 105 50 168 380 420 4 74
540 145 6 3 500 000 13 700 000 355 000 1 390 000 630 29460 500 402 52 140 70 175 410 460 5 140
320 440 73 3 1 190 000 5 450 000 122 000 555 000 950 29264 420 372 21 69 38 172 375 400 2.5 32.5
500 109 5 2 230 000 9 400 000 227 000 960 000 670 29364 470 399 37 105 53 180 400 440 4 77
580 155 7.5 3 650 000 14 600 000 370 000 1 490 000 560 29464 555 436 55 149 75 191 435 495 6 175
340 460 73 3 1 230 000 5 750 000 125 000 590 000 900 29268 440 395 21 69 37 183 395 420 2.5 33.5
540 122 5 2 640 000 11 200 000 269 000 1 140 000 630 29368 510 428 41 117 59 192 430 470 4 103
620 170 7.5 4 400 000 17 400 000 450 000 1 780 000 530 29468 590 462 61 164 82 201 465 530 6 218
360 500 85 4 1 550 000 7 300 000 158 000 745 000 800 29272 480 423 25 81 44 194 420 455 3 51
560 122 5 2 670 000 11 500 000 272 000 1 180 000 600 29372 525 448 41 117 59 202 450 495 4 107
640 170 7.5 4 200 000 17 200 000 430 000 1 750 000 500 29472 610 480 61 164 82 210 485 550 6 228
640 170 7.5 5 450 000 20 400 000 555 000 2 800 000 500 29472 EM 580 474 61 164 83 210 495 550 6 220
380 520 85 4 1 620 000 7 800 000 165 000 795 000 800 29276 496 441 27 81 42 202 440 475 3 52
600 132 6 3 300 000 14 500 000 335 000 1 480 000 560 29376 568 477 44 127 63 216 480 525 5 140
670 175 7.5 4 800 000 19 500 000 490 000 1 990 000 480 29476 640 504 63 168 85 230 510 575 6 254
400 540 85 4 1 640 000 8 000 000 167 000 815 000 750 29280 517 460 27 81 42 212 460 490 3 55
620 132 6 3 250 000 14 500 000 330 000 1 480 000 530 29380 590 494 44 127 64 225 500 550 5 150
710 185 7.5 5 400 000 22 100 000 550 000 2 250 000 450 29480 680 536 67 178 89 236 540 610 6 306
420 580 95 5 2 010 000 9 800 000 205 000 1 000 000 670 29284 553 489 30 91 46 225 490 525 4 72
650 140 6 3 500 000 15 700 000 355 000 1 600 000 500 29384 620 520 48 135 68 235 525 575 5 170
730 185 7.5 5 650 000 23 500 000 575 000 2 400 000 450 29484 700 556 67 178 89 244 560 630 6 323
B 230 B 231
B206-233E.indd 230-231 11/20/13 4:58:29 PM

jd 1 jd a
jd A Dynamic Equivalent Load
ra
r P = 1.2Fr +Fa
B1 Static Equivalent Load
B2 T
C P0 = 2.8Fr +Fa
r ra
However, Fr /Fa0.55 must be
jD1
satisfied.
jD jDa
Boundary Dimensions Basic Load Ratings Limiting Dimensions Abutment and Fillet Mass
(mm) (N) {kgf} Speeds (mm) Dimensions (mm) (kg)
Bearing
(min1) Numbers
d D T r Ca C 0a Ca C 0a Oil d1 D1 B1 B2 C A da(1) Da ra
440 600 95 5 2 030 000 10 100 000 207 000 1 030 000 670 29288 575 508 30 91 49 235 510 545 4 77
680 145 6 3 750 000 16 700 000 380 000 1 710 000 480 29388 645 548 49 140 70 245 550 600 5 190
780 206 9.5 6 550 000 27 200 000 665 000 2 770 000 400 29488 745 588 74 199 100 260 595 670 8 407
780 206 9.5 8 000 000 31 500 000 815 000 3 250 000 400 29488 EM 710 577 74 199 101 257 605 675 8 402
460 620 95 5 2 060 000 10 300 000 210 000 1 050 000 670 29292 592 530 30 91 46 245 530 570 4 80
710 150 6 4 100 000 18 400 000 420 000 1 880 000 450 29392 666 567 51 144 72 257 575 630 5 210
800 206 9.5 6 750 000 28 600 000 690 000 2 920 000 380 29492 765 608 74 199 100 272 615 690 8 420
480 650 103 5 2 370 000 12 100 000 241 000 1 240 000 600 29296 624 556 33 99 55 259 555 595 4 97
730 150 6 4 150 000 19 000 000 425 000 1 940 000 450 29396 690 590 51 144 72 270 595 650 5 215
850 224 9.5 7 200 000 31 000 000 730 000 3 150 000 360 29496 810 638 81 216 108 280 645 730 8 545
500 670 103 5 2 390 000 12 400 000 244 000 1 270 000 600 292/500 645 574 33 99 55 268 575 615 4 100
750 150 6 4 350 000 20 400 000 445 000 2 080 000 450 293/500 715 611 51 144 74 280 615 670 5 220
870 224 9.5 7 850 000 33 000 000 800 000 3 350 000 340 294/500 830 661 81 216 107 290 670 750 8 560
B 232 B 233
B206-233E.indd 232-233 11/20/13 4:58:30 PM

ANGULAR CONTACT THRUST BALL BEARINGS
DOUBLE-DIRECTION ANGULAR
CONTACT THRUST BALL BEARINGS Bore Diameter 35 280mm B238
ANGULAR CONTACT THRUST
BALL BEARINGS FOR BALL SCREWS Bore Diameter 15 60mm B242
DESIGN, TYPE, AND FEATURES

DOUBLE-DIRECTION ANGULAR CONTACT THRUST BALL BEARINGS
Double-Direction Angular Contact Thrust Ball Bearings are specially designed
high precision bearings for the main spindles of machine tools.
Compared with the Thrust Ball Bearings in the 511 Series, this type contains
more balls of smaller diameter and has a contact angle of 60. Consequently,
the influence of centrifugal force is less and they can withstand higher speed
and have higher rigidity.
Bearings in Series 20 and 29 have the same inner and outer diameters as the
double-row cylindrical roller bearings in Series NN30 and NN49 respectively,
and they are both used for high axial loads.
Their cages are machined brass.
There are the BTR, BAR Series of highly rigid angular contact ball bearings
suitable for high speed that can be easily replaced by these double- direction
angular contact ball bearings. For more details, please contact NSK.
ANGULAR CONTACT THRUST BALL BEARINGS FOR BALL SCREWS

Bearings of this type were specially designed to support NSK Precision Ball
Screws. They are usually used in combinations of more than two bearings and
with a preload. Their contact angle is 60. For more details, please refer to
Catalog CAT. No. E1254 SUPER PRECISION BEARINGS.
Their cages are molded polyamide.
B 234 B 235
B234-243E.indd 234-235 11/20/13 4:58:47 PM

TOLERANCES AND RUNNING ACCURACY RECOMMENDED FITS
DOUBLE-DIRECTION ANGULAR CONTACT THRUST DOUBLE-DIRECTION ANGULAR CONTACT THRUST BALL BEARINGS
BALL BEARINGS Table 1
The shaft washer and shaft should be in soft contact with neither interference
ANGULAR CONTACT THRUST BALL BEARINGS FOR nor clearance, and the housing washer and housing bore should be loosely
BALL SCREWS Table 2 fitted. For a bearing arrangement with a double-row cylindrical roller bearing,
The limiting chamfer dimensions of bearings of both types conform to Table 8.9.1 the tolerances for the outside diameter should be f6 to produce a loose fit.
(Page A78).
ANGULAR CONTACT THRUST BALL BEARINGS FOR BALL SCREWS
Table 1 Tolerances for Double-Direction Angular Contact Thrust Ball Bearings (Class 7 (1)) A tolerance of h5 is recommended for shafts and H6 for housing bores.
Table 1. 1 Tolerances for Bearing Bore and Height and Running Accuracy
Units : m
INTERNAL CLEARANCE AND PRELOAD
d & d mp & Ts Kia (or Kea) Sd Sia (or Sea)
In order to produce an appropriate preload on bearings when they are
(mm)
mounted, the following axial internal clearances are recommended.
over incl. high low high low max. max. max.
DOUBLE-ROW ANGULAR CONTACT THRUST
30 0 5 0 300 5 4 3 BALL BEARINGS Clearance C7
30 50 0 5 0 400 5 4 3
50 80 0 8 0 500 6 5 5 ANGULAR CONTACT THRUST BALL BEARINGS FOR
BALL SCREWS Clearance C10
80 120 0 8 0 600 6 5 5
120 180 0 10 0 700 8 8 5
180 250 0 13 0 800 8 8 6
250 315 0 15 0 900 10 10 6
315 400 0 18 0 1200 10 12 7
Note (1) Class 7 is NSK Standard.
Table 1. 2 Tolerances for Housing Washer
Outside Diameter Units : m
Nominal Outside Diameter & Ds
D (mm)
over incl. high low
30 50 25 41
50 80 30 49
80 120 36 58
Symbols in the tables are described on Page A59.
120 180 43 68
180 250 50 79
250 315 56 88
Double-Row Cylindrical Roller Bearing
315 400 62 98 Double-Direction Angular Contact Thrust Ball Bearing
400 500 68 108
500 630 76 120 Example of Application of Double-Direction Angular Contact Thrust Ball Bearing
(Main Spindle of Machine Tool)
Table 2 Tolerances and Running Accuracy of Angular Contact Thrust Ball Bearings for Ball Screws (Class 7A ( )) 1
Table 2. 1 Tolerances and Limits for Shaft and Housing Washer

Units : m Table 2. 2 Tolerances and Running Accuracy of Housing Washer
Nominal Bore Diameter Units : m

d & d mp & Bs (or & Cs) V Bs (or V Cs) Kia Sd Sia Nominal Outside Diameter
(mm) Kea Sea
D &Ds
over incl. high low high low max. max. max. max. (mm)
10 18 0 4 0 120 1.5 2.5 4 2.5 over incl. high low max. max.
18 30 0 5 0 120 1.5 3 4 2.5 30 50 0 6 5 2.5

30 50 0 6 0 120 1.5 4 4 2.5 50 80 0 7 5 2.5
50 80 0 7 0 150 1.5 4 5 2.5 80 120 0 8 5 2.5
Note (1) Class 7A is NSK Standard.
B 236 B 237
B234-243E.indd 236-237 11/20/13 4:58:48 PM

T
C
r1 rb
r ra
jD jd jDa jda
Boundary Dimensions Basic Load Ratings Limiting Speeds Abutment and Fillet Dimensions Mass
(mm) (N) {kgf} (min1) (mm) (kg)
Bearing Numbers
d D ( 1) T C r r1 Ca C 0a Ca C 0a Grease Oil da Da ra rb
35 62 34 17 1 0.6 22 800 53 500 2 330 5 450 10 000 11 000 35 TAC 20X+L 46 58 1 0.6 0.375
40 68 36 18 1 0.6 23 600 59 000 2 410 6 050 9 000 10 000 40 TAC 20X+L 51 63 1 0.6 0.460
45 75 38 19 1 0.6 26 300 67 500 2 680 6 900 8 000 9 000 45 TAC 20X+L 57 70 1 0.6 0.580
50 80 38 19 1 0.6 27 200 74 000 2 780 7 550 7 000 8 000 50 TAC 20X+L 62 75 1 0.6 0.625
55 90 44 22 1.1 0.6 33 500 94 000 3 450 9 550 6 300 6 900 55 TAC 20X+L 69 84 1 0.6 0.945
60 95 44 22 1.1 0.6 35 000 102 000 3 550 10 400 5 900 6 500 60 TAC 20X+L 74 89 1 0.6 1.000
65 100 44 22 1.1 0.6 36 000 110 000 3 700 11 300 5 500 6 100 65 TAC 20X+L 79 94 1 0.6 1.080
70 110 48 24 1.1 0.6 49 500 146 000 5 050 14 900 5 000 5 600 70 TAC 20X+L 87 104 1 0.6 1.460
75 115 48 24 1.1 0.6 50 000 152 000 5 100 15 500 4 800 5 300 75 TAC 20X+L 92 109 1 0.6 1.550
80 125 54 27 1.1 0.6 59 000 181 000 6 000 18 500 4 400 4 900 80 TAC 20X+L 99 117 1 0.6 2.110
85 130 54 27 1.1 0.6 59 500 189 000 6 050 19 300 4 200 4 700 85 TAC 20X+L 104 122 1 0.6 2.210
90 140 60 30 1.5 1 78 500 246 000 8 000 25 100 4 000 4 400 90 TAC 20X+L 110 131 1.5 1 2.930
95 145 60 30 1.5 1 79 500 256 000 8 100 26 100 3 800 4 200 95 TAC 20X+L 115 136 1.5 1 3.050
100 140 48 24 1.1 0.6 55 000 196 000 5 600 20 000 3 800 4 200 100 TAC 29X+L 117 134 1 0.6 1.950
150 60 30 1.5 1 80 500 267 000 8 200 27 200 3 600 4 000 100 TAC 20X+L 120 141 1.5 1 3.200
105 145 48 24 1.1 0.6 56 500 208 000 5 750 21 300 3 600 4 000 105 TAC 29X+L 122 139 1 0.6 2.040
160 66 33 2 1 91 500 305 000 9 350 31 000 3 400 3 800 105 TAC 20X+L 127 150 2 1 4.100
110 150 48 24 1.1 0.6 57 000 215 000 5 800 21 900 3 500 3 900 110 TAC 29X+L 127 144 1 0.6 2.120
170 72 36 2 1 103 000 350 000 10 500 35 500 3 300 3 600 110 TAC 20X+L 134 158 2 1 5.150
120 165 54 27 1.1 0.6 66 500 256 000 6 800 26 100 3 200 3 600 120 TAC 29X+L 139 157 1 0.6 2.940
180 72 36 2 1 106 000 375 000 10 800 38 000 3 000 3 400 120 TAC 20X+L 144 168 2 1 5.500
130 180 60 30 1.5 1 79 500 315 000 8 100 32 500 3 000 3 300 130 TAC 29X+L 150 170 1.5 1 3.950
200 84 42 2 1 134 000 455 000 13 600 46 500 2 800 3 100 130 TAC 20X+L 160 187 2 1 8.200
140 190 60 30 1.5 1 91 500 365 000 9 350 37 500 2 800 3 100 140 TAC 29D+L 158 182 1.5 1 4.200
210 84 42 2 1 145 000 525 000 14 800 53 500 2 600 2 900 140 TAC 20D+L 167 198 2 1 8.750
150 210 72 36 2 1 116 000 465 000 11 800 47 500 2 500 2 800 150 TAC 29D+L 172 200 2 1 6.600
225 90 45 2.1 1.1 172 000 620 000 17 500 63 500 2 400 2 700 150 TAC 20D+L 178 213 2 1 10.700
Note (1) Outside tolerance is f6. Remarks Nominal bearing bore and outside diameters for 20X 20D and 29X 29D bearing series are
the same as those for the NN30 and NNU49 NN49 bearing series respectively.
B 238 B 239
B234-243E.indd 238-239 11/20/13 4:58:49 PM

T
C
r1 rb
r ra
jD jd jDa jda
Boundary Dimensions Basic Load Ratings Limiting Speeds Abutment and Fillet Dimensions Mass
(mm) (N) {kgf} (min1) (mm) (kg)
Bearing Numbers
d D ( 1) T C r r1 Ca C 0a Ca C 0a Grease Oil da Da ra rb
160 220 72 36 2 1 118 000 490 000 12 100 50 000 2 400 2 700 160 TAC 29D+L 182 210 2 1 7.000
240 96 48 2.1 1.1 185 000 680 000 18 900 69 500 2 300 2 500 160 TAC 20D+L 191 228 2 1 13.000
170 230 72 36 2 1 120 000 520 000 12 300 53 000 2 300 2 500 170 TAC 29D+L 192 219 2 1 7.350
260 108 54 2.1 1.1 218 000 810 000 22 200 82 500 2 100 2 400 170 TAC 20D+L 206 245 2 1 17.700
180 250 84 42 2 1 158 000 655 000 16 100 67 000 2 100 2 400 180 TAC 29D+L 207 238 2 1 10.700
280 120 60 2.1 1.1 281 000 1 020 000 28 700 104 000 2 000 2 200 180 TAC 20D+L 220 264 2 1 23.400
190 260 84 42 2 1 161 000 695 000 16 400 71 000 2 000 2 300 190 TAC 29D+L 217 247 2 1 11.200
290 120 60 2.1 1.1 285 000 1 060 000 29 000 108 000 1 900 2 100 190 TAC 20D+L 230 274 2 1 24.400
200 280 96 48 2.1 1.1 204 000 855 000 20 800 87 000 1 900 2 100 200 TAC 29D+L 230 267 2 1 15.700
310 132 66 2.1 1.1 315 000 1 180 000 32 000 120 000 1 800 2 000 200 TAC 20D+L 245 291 2 1 31.500
220 300 96 48 2.1 1.1 210 000 930 000 21 400 95 000 1 800 2 000 220 TAC 29D+L 250 287 2 1 17.000
240 320 96 48 2.1 1.1 213 000 980 000 21 700 100 000 1 700 1 800 240 TAC 29D+L 270 307 2 1 18.300
260 360 120 60 2.1 1.1 315 000 1 390 000 32 000 141 000 1 500 1 700 260 TAC 29D+L 300 344 2 1 31.500
280 380 120 60 2.1 1.1 320 000 1 470 000 32 500 150 000 1 400 1 600 280 TAC 29D+L 320 364 2 1 33.500
Note (1) Outside tolerance is f6. Remarks Nominal bearing bore and outside diameters for 20X 20D and 29X 29D bearing series are
the same as those for the NN30 and NNU49 NN49 bearing series respectively.
B 240 B 241
B234-243E.indd 240-241 11/20/13 4:58:50 PM

BEARINGS FOR SUPPORTING BALL SCREWS
Double-Row Combination Three-Row Combination Four-Row Combination
B Dynamic Equivalent Load

r r1 Pa=X Fr +Y Fa
Rows Two Rows Three Rows Four Rows
60
r
r Combination DF DT DFD DTD DFT DFF DFT
DF DFD DFF Axial Load
One Two One Two Three One Two Three
jDjD1 jd1 jd jd2 jD2 e=2.17
Sustained by
Row Rows Row Rows Rows Row Rows Rows
X 1.90 1.43 2.33 1.17 2.33 2.53
Fa/Fre
Y 0.55 0.77 0.35 0.89 0.35 0.26
X 0.92 0.92 0.92 0.92 0.92 0.92 0.92 0.92

Fa/Fr>e
Y 1 1 1 1 1 1 1 1
DT DTD DFT
Boundary Dimensions Dimensions Limiting Speeds( 1) Mass Basic Load RatingsCa Limiting Axial Load
(mm) (mm) (min1) (kg)
Sustained by Sustained by Sustained by Sustained by Sustained by Sustained by
Bearing Numbers one row two rows three rows one row two rows three rows
d D B r r1 d1 d2 D1 D2 Grease Oil DF DT, DFD, DFF DTD, DFT DF DT, DFD, DFF DTD, DFT
min. min. approx. (N) {kgf} (N) {kgf} (N) {kgf} (N) {kgf} (N) {kgf} (N) {kgf}
15 47 15 1 0.6 27.2 34 34 39.6 6 000 8 000 15 TAC 47B 0.144 21 900 2 240 35 500 3 650 47 500 4 850 26 600 2 710 53 000 5 400 79 500 8 150
17 47 15 1 0.6 27.2 34 34 39.6 6 000 8 000 17 TAC 47B 0.144 21 900 2 240 35 500 3 650 47 500 4 850 26 600 2 710 53 000 5 400 79 500 8 150
20 47 15 1 0.6 27.2 34 34 39.6 6 000 8 000 20 TAC 47B 0.135 21 900 2 240 35 500 3 650 47 500 4 850 26 600 2 710 53 000 5 400 79 500 8 150
25 62 15 1 0.6 37 45 45 50.7 4 500 6 000 25 TAC 62B 0.252 28 500 2 910 46 500 4 700 61 500 6 250 40 500 4 150 81 500 8 300 122 000 12 500
30 62 15 1 0.6 39.5 47 47 53.2 4 300 5 600 30 TAC 62B 0.224 29 200 2 980 47 500 4 850 63 000 6 400 43 000 4 400 86 000 8 800 129 000 13 200
35 72 15 1 0.6 47 55 55 60.7 3 600 5 000 35 TAC 72B 0.31 31 000 3 150 50 500 5 150 67 000 6 850 50 000 5 100 100 000 10 200 150 000 15 300
40 72 15 1 0.6 49 57 57 62.7 3 600 4 800 40 TAC 72B 0.275 31 500 3 250 51 500 5 250 68 500 7 000 52 000 5 300 104 000 10 600 157 000 16 000
90 20 1 0.6 57 68 68 77.2 3 000 4 000 40 TAC 90B 0.674 59 000 6 000 95 500 9 750 127 000 13 000 89 500 9 150 179 000 18 300 269 000 27 400
45 75 15 1 0.6 54 62 62 67.7 3 200 4 300 45 TAC 75B 0.27 33 000 3 350 53 500 5 450 71 000 7 250 57 000 5 800 114 000 11 600 170 000 17 400
100 20 1 0.6 64 75 75 84.2 2 600 3 600 45 TAC 100B 0.842 61 500 6 300 100 000 10 200 133 000 13 600 99 000 10 100 198 000 20 200 298 000 30 500
50 100 20 1 0.6 67.5 79 79 87.7 2 600 3 400 50 TAC 100B 0.778 63 000 6 400 102 000 10 400 136 000 13 800 104 000 10 600 208 000 21 200 310 000 32 000
55 100 20 1 0.6 67.5 79 79 87.7 2 600 3 400 55 TAC 100B 0.714 63 000 6 400 102 000 10 400 136 000 13 800 104 000 10 600 208 000 21 200 310 000 32 000
120 20 1 0.6 82 93 93 102.2 2 200 3 000 55 TAC 120B 1.23 67 500 6 850 109 000 11 200 145 000 14 800 123 000 12 600 246 000 25 100 370 000 37 500
60 120 20 1 0.6 82 93 93 102.2 2 200 3 000 60 TAC 120B 1.16 67 500 6 850 109 000 11 200 145 000 14 800 123 000 12 600 246 000 25 100 370 000 37 500
Note (1) These values apply when the standard preload (C10) is used.
B 242 B 243
B234-243E.indd 242-243 11/20/13 4:58:50 PM

NEEDLE ROLLER BEARINGS
CAGE & NEEDLE ROLLER ASSEMBLIES Inscribed Circle Diameter 5 100mm B252
Cage & Needle Roller Assemblies for Connecting Rod Inscribed Circle Diameter 12 30mm B256
DRAWN CUP NEEDLE ROLLER BEARINGS

With Cage Inscribed Circle Diameter 4 55mm B258
Full Complement Type Inscribed Circle Diameter 8 55mm B258
SOLID NEEDLE ROLLER BEARINGS Inscribed Circle Diameter 9 390mm B264
THRUST NEEDLE ROLLER BEARINGS Bore Diameter 10 100mm B274
CAM FOLLOWERS Outside Diameter 16 90mm B276
ROLLER FOLLOWERS Bore Diameter 5 50mm B278
DESIGN AND TYPES

For needle roller bearings, there are many designs and types bearings.
Catalog
Specified catalog, NSK Needle Roller Bearings CAT.No.E1419 lists bearings
shown in Table 1. Representative examples selected from them, are shown
in this catalog. (shown with in Table 1) For details, please refer
individual specified catalog.
For bearing selection, please contact NSK.
B 244 B 245
B244-279E.indd 244-245 11/20/13 4:59:11 PM

Table1 Types of Needle Roller Bearings Table 2 is applicable to standard drawn cup needle roller bearings (metric series),
and Table 3 shows tolerance of roller inscribed circle diameter based on ISO
Cage & FWJ FBN, FBNP Standards. For bearings assured by ISO Standards, please order by adding symbol
Needle Roller FWF WJC of "-1" at the end of bearing number.
Assemblies WJ FWJC
FJ, FJH FJL MFJ, MFJH MFJL Table 2 Inspection Gauge Dimensions (General Metric) of Table 3 Ring Gauge of Drawn Cup Needle Roller Bearings and
J,JH MJ, MJH Drawn Cup Needle Roller Bearings. Tolerance of Roller Inscribed Circle Diameter (ISO Standards)
F, FH FJ, FJH, MFJ, MFJH FJ, FJH, MFJ and MFJH
Drawn Cup
Needle Roller B, BH
MF, MFH
M, MH
Y
YH (
F, FH, MF, MFH ) (
F, FH, MF and MFH )
FJT, FJTT
Bearings FIR Units mm Units mm
MFJT FJP
FJLT, FJLTT JP IR Nominal Roller Plug Gauge Nominal Roller Tolerance for Roller Inscribed
Bore Diameter Bore Diameter
MFJLT Inscribed Inscribed Circle Diameter, Fw min (1)
RNA 48 Circle Diameter, Fw of Ring Gauge GO Gauge NO-GO Gauge Circle Diameter, Fw of Ring Gauge min. max.
Solid Needle RNA 49
RNA 59 RLM Cone 4 7. 996 4. 023 4. 048 4 7. 984 4. 010 4. 028
Roller Bearings 5 8. 996 5. 023 5. 048 5 8. 984 5. 010 5. 028
RNA 69
HJ RNAF RNATT 6 9. 996 6. 028 6. 053 6 9. 984 6. 010 6. 028
Thrust Needle 7 10. 995 7. 031 7. 056 7 10. 980 7. 013 7. 031
Roller Bearings FNTA FB FTRA FTRB FTRC FTRD FTRE 8 11. 995 8. 031 8. 056 8 11. 980 8. 013 8. 031
Thurst raceway NTA TRA TRB TRC TRD TRE 9 12. 995 9. 031 9. 056 H 8 13. 980 8. 013 8. 031
washers
10 13. 995 10. 031 10. 056 9 12. 980 9. 013 9. 031
A Type F Type P Type 12 15. 995 12. 031 12. 056 H 9 14. 980 9. 013 9. 031
FH 12 17. 995 12. 031 12. 056 10 13. 980 10. 013 10. 031
Needle Rollers (Pleas refer to B350 page) H 10 15. 980 10. 013 10. 031
T Type C Type M Type 13 18. 993 13. 034 13. 059
14 19. 993 14. 034 14. 059 12 15. 980 12. 016 12. 034
15 20. 993 15. 034 15. 059 H 12 17. 980 12. 016 12. 034
Cam Followers FCR FCRS FYCR FYCRS 13 18. 976 13. 016 13. 034
FCJ FCJS FYCJ FYCJS 16 21. 993 16. 034 16. 059
Roller Followers 17 22. 972 17. 013 17. 038 14 19. 976 14. 016 14. 034
CR CRS YCR YCRS
18 23. 972 18. 013 18. 038 15 20. 976 15. 016 15. 034
16 21. 976 16. 016 16. 034
Needle Roller 20 25. 972 20. 013 20. 038
Bearings For ZY NSA 22 27. 972 22. 013 22. 038 17 22. 976 17. 016 17. 034
Universal Joints 25 31. 967 25. 013 25. 038 18 23. 976 18. 016 18. 034
20 25. 976 20. 020 20. 041
28 34. 967 28. 013 28. 038
30 36. 967 30. 013 30. 038 22 27. 976 22. 020 22. 041
Drawn Cup RC FC RCB FCB 35 41. 967 35. 013 35. 043 25 31. 972 25. 020 25. 041
Roller Clutches 28 34. 972 28. 020 28. 041
40 46. 967 40. 013 40. 043
45 51. 961 45. 013 45. 043 30 36. 972 30. 020 30. 041
50 57. 961 50. 013 50. 043 35 41. 972 35. 025 35. 050
55 62. 961 55. 013 55. 043 40 46. 972 40. 025 40. 050
Remarks This is the gauge dimension for Inspection of 45 51. 967 45. 025 45. 050
minimum diameter, Fwmin, of roller inscribed 50 57. 967 50. 025 50. 050
circle diameter. 55 62. 967 55. 030 55. 060
Note (1) When using a cylinder instead of an inner ring,
DIMENSIONAL ACCURACY RUNNING ACCURACY Fwmin is the diameter of the cylinder at which the
internal clearance is zero in at least one radial
DRAWN CUP NEEDLE ROLLER BEARINGS direction. (Fwmin is the minimum diameter of
The correct form and dimensional accuracy of outer ring of drawn cup each inscribed circle diameter where deviation is
needle roller bearing is achieved only by press fitting into proper housing with assumed.)
Remarks To measure the roller inscribed circle diameter,
appropriate interference. Therefore, roller inscribed circle diameter is measured use the following plug gauges:
after press fitted into a standard ring gauge. GO gauge: The same dimensions as the
The dimension of ring gauge and tolerance of roller inscribed circle diameter minimum tolerance of the roller
are shown in Tables 2 and 3. inscribed circle diameter Fwmin.
NO-GO gauge: The dimensions should be the
maximum tolerance of roller
inscribed circle diameter, Fwmin,
plus 0.002 mm.
B 246 B 247
B244-279E.indd 246-247 11/20/13 4:59:12 PM

SOLID NEEDLE ROLLER BEARINGS Table 8. 2 (A60-63 pages) DRAWN CUP NEEDLE ROLLER BEARINGS
Tolerance of roller inscribed circle diameter for solid needle roller bearings For FJ, FJH, and MFJH types and F, FH, and MFH types, if tolerance
without inner rings are shown in Table 4. of fitting such as shaft:h6, and housing bore:N7 (in case of thick steel
Table 4 Inscribed Circle Diameter for Metric Solid housing), are applied under general operating condition, appropriate radial
Needle Roller Bearings Units m internal clearance is obtained. In case that outer ring rotation, the fitting of
Deviation (F6) of Minimum shaft : f6, housing bore : R7, and light alloy housing or steel housing of less
Nominal Inscribed
Diameter, Fw min, of Roller than 6mm thickness, the housing bore should be smaller than N7 by 0.013
Circle Diameter, Fw
Inscribed Circle Diameter Fw min(1) 0.025 mm.
(mm)
& Fw min
over incl. high low SOLID NEEDLE ROLLER BEARINGS
6 10 + 22 +13 Recommended fitting for solid needle roller bearings with inner rings
10 18 + 27 +16 Table 9. 2 (Page A84)
18 30 + 33 +20
Table 9. 4 (Page A85)
30 50 + 41 +25 Internal clearance of solid needle roller bearings with inner rings
50 80 + 49 +30 Table 9. 14 (Page A91)
80 120 + 58 +36
However, for needle roller bearing of wider bearing width, and with long
120 180 + 68 +43 needle rollers, bearings with CN clearance are not necessarily common,
180 250 + 79 +50
250 315 + 88 +56 but large clearance is selected frequently. For the solid needle roller bearing
without inner ring, it is possible to select radial internal clearance shown in
315 400 + 98 +62
400 500 +108 +68 Table 6 by selecting tolerance class of shaft, which is fitting to the bearing.
Note (1) When using a cylinder instead of an inner ring, Table 6 Fitting Tolerances and Radial Internal clearance of Shafts Assembled
Fw min is the diameter of the cylinder at which the with Solid Needle Roller Bearings without Inner Rings
internal clearance is zero in at least one radial
direction. (F w min is the minimum diameter of
each inscribed circle diameter where deviation is Nominal Roller Inscribed
assumed.) Circle Diameter Fw (mm) C2 CN C3 C4
CAM FOLLOWERS ROLLER FOLLOWERS Table 8. 2 (A60-63 pages) over incl.
The tolerance zone class of stud diameter d of cam followers is h7, and 6 180 k5 g5 f6 e6
the tolerance of assembled width of inner ring of roller followers is shown in
bearing table. 180 315 j6 f6 e6 d6
These tolerances are applied to the bearings before surface treatment. 315 490 h6 e6 d6 c6
Cam Follower Dimensional Tolerences is always applited to the bearing
before surface treatment.
THRUST NEEDLE ROLLER BEARINGS
RECOMMENDED FITTING AND BEARING INTERNAL CLEARANCE Recommended Fitting of Thrust Needle Roller Bearings and Thrust Raceway are shown
CAGE & NEEDLE ROLLER ASSEMBLIES in Table 7.
Recommended fitting of cage & roller under typical operating condition Table 7 Recommended Fitting of Thrust Needle Roller Bearings and Thrust Raceway
is shown in Table 5. By combining cage & roller, shaft, and housing, Units mm
appropriate radial internal clearance is obtained. However, the fitting and Cage or Tolerance class or dimension tolerance
the radial internal clearance of cage & roller for connecting rod should be Classification Type
raceway guide Shaft Housing bore
determined by the type of engine, characteristic, and driving condition etc.. Thrust Needle Bearing Cage Bore h8 Dc (1)+over 1.0
For details, please refer to specified catalog. FNTA
& Needle Roller Assemblies Outside H10
Table 5 Fitting Tolerances for Shafts and Housing Bores Bore h8 Dc (1)+over 1.0
Thrust Bearing Rings FTRA to FTRE
Fitting Tolerance Outside H10
Operating Conditions shaft Note (1) Dc represents outside diameter of the cage.
housing bore
Fw50 mm Fw>50 mm Remarks If the cage is guided by outside diameter, to prevent the wear of housing
bore, it is necessary to harden the surface at least.
High Accuracy, Oscillating Motion js5 (j5) h5
Normal h5 g5 G6
High Temperature, Large Shaft Deflection
f6
and Mounting Error of Bearings
B 248 B 249
B244-279E.indd 248-249 11/20/13 4:59:46 PM

CAM FOLLOWERS ROLLER FOLLOWERS Specifications of Thrust Bearings Raceway Surface are shown in Table 11.
The recommended fittings for the mounting area of cam follower studs are Table 11 Specifications of Thrust Bearings Raceway Surface
shown in Table 8. Recommended shaft fittings of roller follower are shown
in Table 9.
Since cam followers are used with cantilevered mounting, they should be Squareness A 0.5/1000 incl (mm/mm)
fixed with little clearance of the fitting surface as much as possible.
Since a roller follower is generally used with outer ring rotation, the fitting
with shaft is transition or loose fit. In case that heavy loads impose to the Squareness B 1.0/1000 incl (mm/mm)
roller follower, it is recommended to use the shaft of quench hardening
treatment, and with tight fit. Roughness
For the details, please refer to specified catalog. 0.4
Ra (m)
Table 8 Recommended Fitting for Stud Table 9 Recommended Staft Fittings HRC58 to 64
Mounting Part of Cam Followers of Roller Followers Hardness
(HRC60 to 64 is fovorable)
Fitting Tolerance of
Type Load Fitting Tolerance of Shaft
Mounting Hole LIMITING INCLINATION ANGLES
FCR, FCRS Light Load/Normal Load g6 or h6
JS7 (J7) The limiting inclination angle of radial needle roller bearing under general
FCJ, FCJS Heavy Load k6 load condition is 0.001 radian (3.4') approximately. For the detail, please
refer to specified catalog.,
SHAFT AND HOUSING SPECIFICATIONS Table 12 Permissble Load PERMISSBLE TRACK LOAD
The specification of shaft and housing for radial needle roller bearings, Coefficient of Track
which are used under general operating condition, is shown in Table 10. The permissble load of the track is determined by compression strength or
Hardness Coefficient
(HRC)
hardness. The permissble load of the track shown in the bearing table is value
Table 10 Shaft and housing Specifications of Radial Needle Roller Bearings of a track made of steel with a hardness of HRC40. Table 12 indicates the
(Cage & Needle Roller Assemblies/Drawn Cup Bearings/Solid Bearings) 20 0.4 permissible load coefficient of the track for each hardness.
25 0.5 The permissible load of the track for each hardness can be obtained by
30 0.6
Category
Shaft Housing Bore multiplying the permissible load coefficient of the track corresponding to each
Raceway Surface Fitting Surface Raceway Surface Fitting Surface 35 0.8 hardness.
Out-of-Roundness IT3 IT3 IT4 IT3 IT4 IT5 40 1.0
Tolerance to to 45 1.4
2 2 2 2 2 2
Cylindricity IT3 IT3 IT4 IT3 IT4 IT5
PRE-PACKED GREASE
Tolerance 2
to
2
to 50 1.9
2 2 2 2 The cam follower/roller follower with a seal is pre-lubricated with lithium
55 2.6
Roughness soap-based grease. The range of operating temperature is 10 to +110C.
0.4 0.8 0.8 1.6 58 3.2
Ra ( m) For the cam follower/roller follower without seal, please lubricate with
HRC58 to 64 HRC58 to 64 suitable lubricant.
Hardness Appropriate depth Appropriate depth
of hardening layer of hardening layer
required required
Remarks 1. For the specification of shaft and housing of cage & needle roller assembly for
MAXIMUM PERMISSIBLE LOAD AND MAXIMUM CLAMP TORQUE
connecting rod, please refer to specified catalog.
OF CAM FOLLOWERS.
2. These are general recommendation by radius method. For the value of The maximum radial Load that the cam follower can carry is determined
standard tolerance (IT), please refer to Appendix 11 (page C22) by the bearing strengh and shear strengh of the stud rather than the Load
rating for neele bearings. This value is given in the bearing table as the
maximum permissible Load.
Since the stud of the cam follower receives bending stress and tensile
stress from the bearing Load, the screw clamp torque should not exceed
the value shown in the bearing table.
LIMITING SPEED
The limiting speeds of bearings are shown in bearing tables. However,
depending on load condition of the bearing, the limiting speeds are
necessary to compensate. Also, improvement of lubrication method allows
to take higher limiting speed. For the detail, please refer to A37 page.
B 250 B 251
B244-279E.indd 250-251 11/20/13 4:59:46 PM

CAGE & NEEDLE ROLLER ASSEMBLIES
FWF FWJ
Inscribed Circle Diameter 5 22 mm
Bc
jEw jFw
Boundary Dimensions Basic Load Ratings Limiting Speeds Mass

(mm) (N) {kgf} (min1) (g)
0.2 Bearing Numbers
0.55
FW EW BC Cr C 0r Cr C 0r Grease Oil
approx.
5 8 8 2 330 1 860 237 189 60 000 95 000 * FBNP-588 1.0
6 9 8 2 200 1 780 224 182 48 000 75 000 * FBNP-698 1.2
9 10 3 350 3 050 340 310 48 000 75 000 * FBNP-6910 1.5
7 10 8 2 840 2 560 290 261 40 000 67 000 * FBNP-7108 1.3
10 10 3 650 3 550 375 360 40 000 67 000 * FBNP-71010 1.6
8 11 10 3 950 4 000 400 410 34 000 56 000 * FBNP-81110 1.8
11 13 4 750 5 150 485 525 34 000 56 000 * FBNP-81113 2.6
9 12 10 3 750 3 850 380 395 30 000 50 000 * FBNP-91210 2.0
12 13 5 100 5 750 520 585 30 000 50 000 * FBNP-91213 2.6
10 13 10 3 950 4 300 405 435 28 000 45 000 FBN-101310 2.2
13 13 5 400 6 350 550 650 28 000 45 000 FBN-101313 2.9
14 13 6 500 6 750 660 690 28 000 45 000 FWF-101413 4.0
12 15 10 4 350 5 100 445 520 22 000 36 000 FBN-121510 2.6
15 13 5 950 7 600 605 775 22 000 36 000 FBN-121513 3.4
16 13 7 350 8 350 750 850 22 000 38 000 FWF-121613 4.6
14 18 10 6 750 7 750 690 790 19 000 32 000 FWF-141810 4.1
18 13 8 050 9 750 820 995 19 000 32 000 FWF-141813 5.3
20 17 13 400 14 600 1 370 1 490 20 000 32 000 FWF-142017 11
15 19 10 7 050 8 400 720 855 18 000 28 000 FWF-151910 4.3
19 13 8 400 10 500 860 1 070 18 000 28 000 FWF-151913 5.6
21 17 13 400 14 800 1 370 1 510 19 000 30 000 FWF-152117 12
16 20 10 7 350 9 000 750 920 17 000 26 000 FWF-162010 4.6
20 13 8 800 11 300 895 1 150 17 000 26 000 FWF-162013 6.0
22 17 14 700 16 900 1 500 1 720 17 000 28 000 FWF-162217 12
17 21 10 7 650 9 650 780 985 16 000 26 000 FWF-172110 4.8
21 13 10 200 14 000 1 040 1 420 16 000 26 000 FWJ-172113 6.3
23 17 15 100 17 800 1 540 1 810 16 000 26 000 FWF-172317 14
18 22 10 7 900 10 300 805 1 050 15 000 24 000 FWF-182210 5.1
22 13 9 450 12 900 965 1 310 15 000 24 000 FWF-182213 6.6
24 17 17 400 21 600 1 770 2 210 15 000 24 000 FWJ-182417 14
20 24 10 8 000 10 700 815 1 090 13 000 20 000 FWF-202410 5.6
24 13 9 700 13 700 990 1 400 13 000 20 000 FWF-202413 7.3
26 17 18 000 23 200 1 830 2 370 14 000 22 000 FWJ-202617 15
22 26 10 8 600 12 200 880 1 240 12 000 19 000 FWF-222610 6.1
26 13 10 300 15 300 1 050 1 560 12 000 19 000 FWF-222613 7.9
28 17 17 300 22 700 1 760 2 310 12 000 20 000 FWF-222817 16
Note (*) These bearings have polyamide cages. The maximum permissible operating temperature for these bearings is 100C
for continued operation and 120C for short periods.
B 252 B 253
B244-279E.indd 252-253 11/20/13 4:59:47 PM

FWF FWJ
Bc
jEw jFw
Boundary Dimensions Basic Load Ratings Limiting Speeds Mass

(mm) (N) {kgf} (min1) (g)
0.2 Bearing Numbers
0.55
FW EW BC Cr C 0r Cr C 0r Grease Oil
approx.
25 29 10 9 350 14 100 950 1 440 10 000 17 000 FWF-252910 6.9
29 13 11 300 18 000 1 150 1 830 10 000 17 000 FWF-252913 8.9
31 17 19 200 26 800 1 950 2 740 10 000 17 000 FWF-253117 18
28 33 13 13 700 20 400 1 400 2 080 9 500 15 000 FWF-283313 13
33 17 17 600 28 300 1 800 2 890 9 500 15 000 FWF-283317 16
34 17 19 900 29 100 2 020 2 970 9 500 15 000 FWF-283417 20
30 35 13 14 000 21 600 1 430 2 200 8 500 14 000 FWF-303513 14
35 17 18 700 31 500 1 910 3 200 8 500 14 000 FWF-303517A 18
37 20 26 000 38 000 2 650 3 850 9 000 14 000 FWF-303720 30
32 37 13 15 100 24 400 1 540 2 480 8 000 13 000 FWF-323713 14
37 17 18 500 31 500 1 880 3 200 8 000 13 000 FWJ-323717 19
39 20 27 300 41 000 2 780 4 200 8 500 13 000 FWF-323920 32
35 40 13 14 900 24 600 1 520 2 500 7 500 12 000 FWF-354013 16
40 17 20 500 37 000 2 090 3 750 7 500 12 000 FWF-354017 20
42 20 30 000 47 500 3 050 4 850 7 500 12 000 FWJ-354220 34
40 45 17 21 000 40 000 2 150 4 050 6 300 10 000 FWF-404517A 23
45 27 32 000 68 000 3 250 6 900 6 300 10 000 FWF-404527 36
48 25 40 500 66 500 4 150 6 800 6 700 10 000 FWF-404825 56
45 50 17 21 600 43 000 2 200 4 350 5 600 9 000 FWF-455017 26
50 27 34 000 77 500 3 500 7 900 5 600 9 000 FWF-455027 41
53 25 44 000 77 000 4 500 7 850 5 600 9 500 FWF-455325 62
50 55 20 26 900 59 000 2 750 6 050 5 000 8 000 FWF-505520 37
55 27 35 000 83 000 3 600 8 450 5 000 8 000 FWF-505527 50
58 25 48 500 90 500 4 950 9 200 5 300 8 500 FWF-505825 77
55 61 20 31 000 64 000 3 150 6 500 4 500 7 500 FWF-556120 53
61 30 47 000 109 000 4 750 11 100 4 500 7 500 FWF-556130 81
63 25 50 000 97 500 5 100 9 950 4 800 7 500 FWF-556325 85
60 66 20 33 000 71 500 3 350 7 300 4 300 6 700 FWF-606620 57
66 30 50 000 122 000 5 100 12 400 4 300 6 700 FWF-606630 87
68 25 52 000 105 000 5 300 10 700 4 300 6 700 FWF-606825 91
65 73 30 61 000 132 000 6 200 13 400 4 000 6 300 FWF-657330 120
70 78 30 63 000 140 000 6 400 14 300 3 600 6 000 FWF-707830 125
75 83 30 65 000 151 000 6 650 15 400 3 400 5 600 FWF-758330 135
80 88 30 69 000 166 000 7 050 17 000 3 200 5 000 FWF-808830 145
85 93 30 71 000 176 000 7 250 17 900 3 000 4 800 FWF-859330 150
90 98 30 70 000 177 000 7 150 18 000 2 800 4 500 FWF-909830 160
95 103 30 69 500 177 000 7 100 18 100 2 600 4 300 FWF-9510330 175
100 108 30 75 500 201 000 7 700 20 500 2 400 4 000 FWF-10010830 185
B 254 B 255
B244-279E.indd 254-255 11/20/13 4:59:48 PM

Cage & Needle Roller Assemblies for Large Ends of Connecting Rods Cage & Needle Roller Assemblies for Small Ends of Connecting Rods
Inscribed Circle Diameter 12 30 mm Inscribed Circle Diameter 9 19 mm
Bc
Bc
jEw jFw jEw jFw
Boundary Dimensions Basic Load Ratings Mass Boundary Dimensions Basic Load Ratings Mass
(mm) (N) {kgf} (g) (mm) (N) {kgf} (g)
0.2 Bearing Numbers 0.2 Bearing Numbers
0.4 0.4
FW EW BC Cr C 0r Cr C 0r FW EW BC Cr C 0r Cr C 0r
approx. approx.
12 16 10 6 100 6 500 620 665 FWF-121610-E 4.0 9 12 11.5 4 300 4 650 440 475 FBN-91211Z-E 3.5
14 19 10 7 800 8 050 795 820 FWF-141910-E 6.2
20 12 8 900 8 600 910 880 FWF-142012-E 8.3 10 14 12.7 5 900 5 950 605 610 FBN-101412Z-E 5.0
12 15 14.3 6 400 8 400 655 855 FBN-121514Z-E 4.8

15 19 9 5 650 6 250 575 640 FWF-15199-E 4.1 16 13 7 250 8 200 740 835 FBN-121613-E 6.4
20 10 7 300 7 600 745 775 FWF-152010-E 6.0 16 15.5 8 500 10 000 865 1 020 FBN-121615Z-E 7.0
21 10 7 950 7 500 810 765 FWF-152110-E 8.5 16 16 8 500 10 000 865 1 020 FBN-121616-E 7.5
14 18 12 6 950 8 050 710 820 FBN-141812-E 6.5

16 21 11 8 650 9 600 880 980 FWF-162111-E 7.5 18 16.5 9 250 11 600 945 1 180 FBN-141816Z-E 8.5
22 12 9 500 9 600 965 980 FWF-162212-E 9.5 18 18 10 700 14 000 1 090 1 430 FBN-141818-E 11.5
18 20 9 550 12 000 975 1 230 FBN-141820-E1 13
18 23 14 11 800 14 800 1 200 1 510 FWF-182314-E 10 15 19 18 11 300 15 300 1 150 1 560 FBN-151918-E 11
24 12 10 000 10 600 1 020 1 080 FWF-182412-E 11 21 18 12 900 13 900 1 310 1 420 FBN-152118-E 13
16 20 22 13 700 20 000 1 400 2 040 FBN-162022-E 14

20 26 12 12 200 14 100 1 250 1 440 FWF-202612-E 13 20 23.5 14 900 22 300 1 520 2 280 FBN-162023Z-E 15
26 17 16 800 21 200 1 710 2 160 FWF-202617-E 17 21 20 14 200 18 100 1 450 1 840 FBN-162120-E 16
28 18 18 100 19 400 1 840 1 970 FWF-202818-E 25
17 21 23 14 800 22 500 1 510 2 290 FBN-172123-E 16
22 28 14 13 900 17 100 1 420 1 740 FWF-222814-E 14
29 15 16 300 19 000 1 660 1 930 FWF-222915-E 19 18 22 17 11 500 16 500 1 170 1 680 FBN-182217-E 12
32 16 19 700 19 400 2 010 1 970 FWF-223216-E 31 22 22 14 200 21 600 1 440 2 200 FBN-182222-E 15
22 23.6 15 400 24 100 1 570 2 460 FBN-182223Z-E 16
23 31 16 17 600 19 400 1 800 1 980 FWF-233116-E 23 19 23 23.7 16 000 25 800 1 630 2 630 FBN-192323Z-E 17
24 30 15 15 600 20 300 1 590 2 070 FWF-243015-E 17
30 17 17 900 24 300 1 830 2 480 FWF-243017-E 19
31 20 21 600 27 800 2 200 2 840 FWF-243120-E 30
25 32 16 17 700 21 900 1 810 2 230 FWF-253216-E 24

28 35 16 18 400 23 700 1 880 2 410 FWF-283516-E 25
29.75 36.75 16.5 19 600 26 000 1 990 2 650 FWF-293616Z-E 28
30 37 16 21 900 30 500 2 230 3 100 FWF-303716-E 29

38 18 25 500 34 000 2 600 3 450 FWF-303818-E 35
B 256 B 257
B244-279E.indd 256-257 11/20/13 4:59:48 PM

FJ MFJ (With Cage)
F MF (Full Complement Type)
C C C C
C2 ra
C1 B
Housing
jFw jd Shaft
jD jFw jD jFw jD jFw jD jFw Bore jda
N7 h6
Open Type Closed Type Open Type Closed Type With Inner Ring
With Cage Full Complement Type
Boundary Dimensions Basic Dynamic Load Ratings Limiting Loads Limiting Speeds Bearing Numbers In case of inner ring is used Mass Without Inner Ring
(mm) (N) {kgf} (N) {kgf} (min1) (g)
0
With Cage Full Complement Type Bearing Numbers Boundary Abutment and Fillet
0.25
FW D C C 1,C 2 Cr P max Grease Oil of Inner Ring Dimensions (mm) Dimensions (mm) approx.
max. Open Closed Open Closed d B d a(min.) ra(max.) Open Closed
4 8 8 0.8 1 720 175 675 69 45 000 75 000 * FJP-48 - - - - 1.3

5 9 9 0.8 1 860 190 745 76 43 000 71 000 FJ-59 MFJ-59 - - - 1.7 1.9
6 10 9 0.8 2 320 237 985 101 36 000 56 000 FJ-69 MFJ-69 - - - 2.2 2.4
7 11 9 0.8 2 550 260 1 110 113 30 000 48 000 FJ-79 MFJ-79 - - - 2.3 2.7
8 12 10 0.8 2 840 289 1 270 130 26 000 43 000 FJ-810 MFJ-810 - - - 2.7 3.2
14 10 1.0 4 300 435 1 770 180 28 000 45 000 FJH-810 MFJH-810 - - - 5.2 5.5
14 10 1.9 5 550 565 2 980 305 6 300 10 000 - - FH-810 MFH-810 - 6.0 6.3
9 13 10 0.8 3 300 335 1 600 163 22 000 36 000 FJ-910 MFJ-910 - - - 3.2 3.6
15 10 1.0 4 550 465 1 910 194 24 000 40 000 FJH-910 MFJH-910 - - - 5.7 6.1
15 10 1.8 6 100 625 3 350 340 6 000 10 000 - - FH-910 MFH-910 - 6.4 6.8
10 14 10 0.8 3 500 360 1 760 179 20 000 32 000 FJ-1010 MFJ-1010 - - FIR-71010 7 10.5 9 0.3 3.6 4.1
16 10 1.0 4 900 500 2 100 214 22 000 34 000 FJH-1010 MFJH-1010 - - FIR-71010 7 10.5 9 0.3 6.1 6.6
16 10 1.9 6 650 680 3 700 375 5 600 9 000 - - FH-1010 MFH-1010 FIR-71010 7 10.5 9 0.3 6.9 7.3
12 16 10 0.8 4 150 420 2 210 225 17 000 26 000 FJ-1210 MFJ-1210 - - FIR-81210 8 10.5 10 0.3 4.1 4.5
18 12 1.0 6 450 655 3 050 310 17 000 28 000 FJH-1212 MFJH-1212 - - FIR-81212 8 12.5 10 0.3 7.7 8.2
18 12 1.9 9 000 920 5 700 580 4 500 7 500 - - FH-1212 MFH-1212 FIR-81212 8 12.5 10 0.3 10 11
13 19 12 1.0 6 950 710 3 400 345 16 000 26 000 FJ-1312 MFJ-1312 - - FIR-101312 10 12.5 12 0.3 8.6 9.5
19 12 1.9 9 550 975 6 100 625 4 300 7 100 - - F-1312 MF-1312 FIR-101312 10 12.5 12 0.3 11 12
14 20 12 1.0 6 500 665 3 250 335 15 000 24 000 FJ-1412 MFJ-1412 - - FIR-101412 10 12.5 12 0.3 10 11
20 12 2.2 9 450 965 6 350 645 3 800 6 000 - - F-1412 MF-1412 FIR-101412 10 12.5 12 0.3 12 14
20 16 1.0 9 500 970 5 300 540 15 000 24 000 FJ-1416 MFJ-1416 - - FIR-101416 10 16.5 12 0.3 13 14
20 16 2.2 13 300 1 360 9 850 1 000 3 800 6 000 - - F-1416 MF-1416 FIR-101416 10 16.5 12 0.3 18 19
15 21 12 1.0 7 650 780 3 900 400 14 000 22 000 FJ-1512 MFJ-1512 - - FIR-121512 12 12.5 14 0.3 10 11
21 12 1.8 10 300 1 050 6 900 705 3 800 6 000 - - F-1512 MF-1512 FIR-121512 12 12.5 14 0.3 12 14
21 14 1.8 12 400 1 270 8 800 895 3 800 6 000 - - F-1514 MF-1514 - 15 16
21 16 1.0 11 000 1 120 6 200 635 14 000 22 000 FJ-1516 MFJ-1516 - - FIR-121516 12 16.5 14 0.3 13 14
21 16 1.8 14 500 1 480 10 700 1 090 3 800 6 000 - - F-1516 MF-1516 FIR-121516 12 16.5 14 0.3 17 18
16 22 12 1.0 7 100 725 3 750 380 12 000 20 000 FJ-1612 MFJ-1612 - - FIR-121612 12 12.5 14 0.3 11 12
22 12 2.2 10 200 1 040 7 100 725 3 400 5 300 - - F-1612 MF-1612 FIR-121612 12 12.5 14 0.3 14 15
22 16 1.0 10 400 1 060 6 050 620 12 000 20 000 FJ-1616 MFJ-1616 - - FIR-121616 12 16.5 14 0.3 14 15
22 16 2.2 14 400 1 460 11 100 1 130 3 400 5 300 - - F-1616 MF-1616 FIR-121616 12 16.5 14 0.3 18 20
Note (*) These bearing have polyamide cages. The maximum permissible operating temperature for these bearings is 100C for
continued operation and 120C for short periods.
B 258 B 259
B244-279E.indd 258-259 11/20/13 4:59:49 PM

FJ MFJ (With Cage)
C C C C
C2 ra
C1 B
Housing
jFw jd Shaft
N7 h6
0
0.25
17 23 12 1.0 8 450 860 4 450 455 12 000 19 000 FJ-1712 MFJ-1712 - - - - - - - 10 11
23 12 1.8 11 300 1 150 7 750 790 3 400 5 600 - - F-1712 MF-1712 - - - - - 14 15
23 16 1.0 12 100 1 230 7 100 720 12 000 19 000 FJ-1716 MFJ-1716 - - - - - - - 14 16
23 16 1.8 15 800 1 610 12 000 1 220 3 400 5 600 - - F-1716 MF-1716 - - - - - 18 20
18 24 12 1.0 7 650 780 4 200 430 11 000 18 000 FJ-1812 MFJ-1812 - - FIR-151812 15 12.5 17 0.3 12 14
24 12 2.2 10 900 1 110 7 900 805 3 000 5 000 - - F-1812 MF-1812 FIR-151812 15 12.5 17 0.3 14 16
24 16 1.0 11 200 1 140 6 800 695 11 000 18 000 FJ-1816 MFJ-1816 - - FIR-151816 15 16.5 17 0.3 16 18
24 16 2.2 15 300 1 560 12 300 1 250 3 000 5 000 - - F-1816 MF-1816 FIR-151816 15 16.5 17 0.3 19 22
20 26 12 1.0 8 150 835 4 650 475 10 000 16 000 FJ-2012 MFJ-2012 - - FIR-172012 17 12.5 19 0.3 13 15
26 12 2.2 11 500 1 170 8 700 885 2 800 4 500 - - F-2012 MF-2012 FIR-172012 17 12.5 19 0.3 17 19
26 16 1.0 11 900 1 210 7 550 770 10 000 16 000 FJ-2016 MFJ-2016 - - FIR-172016 17 16.5 19 0.3 17 19
26 16 2.2 16 200 1 650 13 500 1 380 2 800 4 500 - - F-2016 MF-2016 FIR-172016 17 16.5 19 0.3 22 25
26 20 1.0 15 300 1 560 10 500 1 070 10 000 16 000 FJ-2020 MFJ-2020 - - FIR-172020 17 20.5 19 0.3 22 24
26 20 2.2 20 500 2 090 18 300 1 870 2 800 4 500 - - F-2020 MF-2020 FIR-172020 17 20.5 19 0.3 28 30
22 28 12 1.0 8 650 880 5 150 525 9 000 14 000 FJ-2212 MFJ-2212 - - FIR-172212 17 12.5 19 0.3 14 17
28 12 2.2 12 100 1 230 9 500 970 2 400 4 000 - - F-2212 MF-2212 FIR-172212 17 12.5 19 0.3 18 21
28 16 1.0 12 600 1 290 8 350 850 9 000 14 000 FJ-2216 MFJ-2216 - - FIR-172216 17 16.5 19 0.3 19 22
28 16 2.2 17 100 1 740 14 800 1 510 2 400 4 000 - - F-2216 MF-2216 FIR-172216 17 16.5 19 0.3 24 27
28 20 1.0 16 200 1 660 11 500 1 180 9 000 14 000 FJ-2220 MFJ-2220 - - FIR-172220 17 20.5 19 0.3 23 26
28 20 2.2 21 600 2 200 20 000 2 040 2 400 4 000 - - F-2220 MF-2220 FIR-172220 17 20.5 19 0.3 30 33
25 32 16 1.0 15 200 1 550 9 350 955 8 000 13 000 FJ-2516 MFJ-2516 - - FIR-202516 20 16.5 22 0.3 24 27
32 16 2.5 20 200 2 060 16 200 1 650 2 800 4 500 - - F-2516 MF-2516 FIR-202516 20 16.5 22 0.3 31 35
32 20 1.0 19 800 2 020 13 100 1 340 8 000 13 000 FJ-2520 MFJ-2520 - - FIR-202520 20 20.5 22 0.3 31 34
32 20 2.5 25 900 2 640 22 200 2 260 2 800 4 500 - - F-2520 MF-2520 FIR-202520 20 20.5 22 0.3 40 43
32 26 1.0 26 200 2 670 18 800 1 920 8 000 13 000 FJ-2526 MFJ-2526 - - FIR-202526 20 26.5 22 0.3 40 43
32 26 2.5 34 000 3 450 31 500 3 200 2 800 4 500 - - F-2526 MF-2526 FIR-202526 20 26.5 22 0.3 52 55
28 35 16 1.0 15 600 1 590 9 950 1 020 7 100 11 000 FJ-2816 MFJ-2816 - - FIR-222816 22 16.5 24 0.3 27 31
35 16 2.5 21 300 2 170 17 900 1 820 2 400 4 000 - - F-2816 MF-2816 FIR-222816 22 16.5 24 0.3 35 40
35 20 1.0 20 500 2 090 14 200 1 450 7 100 11 000 FJ-2820 MFJ-2820 - - FIR-222820 22 20.5 24 0.3 34 38
35 20 2.5 27 300 2 780 24 600 2 510 2 400 4 000 - - F-2820 MF-2820 FIR-222820 22 20.5 24 0.3 44 48
35 26 1.0 26 900 2 750 20 200 2 060 7 100 11 000 FJ-2826 MFJ-2826 - - FIR-222826 22 26.5 24 0.3 45 49
35 26 2.5 35 500 3 650 34 500 3 550 2 400 4 000 - - F-2826 MF-2826 FIR-222826 22 26.5 24 0.3 57 62
B 260 B 261
B244-279E.indd 260-261 11/20/13 4:59:50 PM

FJ MFJ (With Cage)
C C C C
C2 ra
C1 B
Housing
jFw jd Shaft
N7 h6
0
0.25
30 37 16 1.0 15 600 1 590 10 100 1 030 6 700 10 000 FJ-3016L MFJ-3016 - - - - - - - 26 31
37 16 2.5 22 100 2 250 18 900 1 930 2 400 3 800 - - F-3016 MF-3016 - - - - - 35 40
37 20 1.0 19 400 1 970 13 300 1 360 6 700 10 000 FJ-3020 MFJ-3020 - - FIR-253020 25 20.5 27 0.3 35 39
37 20 2.5 28 400 2 900 26 200 2 670 2 400 3 800 - - F-3020 MF-3020 FIR-253020 25 20.5 27 0.3 46 51
37 26 1.0 26 000 2 660 19 500 1 990 6 700 10 000 FJ-3026 MFJ-3026 - - FIR-253026 25 26.5 27 0.3 46 50
37 26 2.5 37 000 3 800 37 000 3 750 2 400 3 800 - - F-3026 MF-3026 FIR-253026 25 26.5 27 0.3 61 66
35 42 16 1.0 18 100 1 850 12 800 1 300 5 600 9 000 FJ-3516 MFJ-3516 - - - - - - - 32 38

42 16 2.5 24 000 2 450 22 000 2 240 2 000 3 400 - - F-3516 MF-3516 - - - - - 53 60
42 20 1.0 23 600 2 410 17 900 1 830 5 600 9 000 FJ-3520 MFJ-3520 - - FIR-303520 30 20.5 34 0.6 41 45
42 20 2.5 31 000 3 150 30 000 3 100 2 000 3 400 - - F-3520 MF-3520 FIR-303520 30 20.5 34 0.6 42 49
42 26 1.0 31 500 3 200 25 800 2 630 5 600 9 000 FJ-3526 MFJ-3526 - - FIR-303526 30 26.5 34 0.6 54 58
42 26 2.5 40 000 4 100 42 500 4 350 2 000 3 400 - - F-3526 MF-3526 FIR-303526 30 26.5 34 0.6 70 76
40 47 16 1.0 18 600 1 890 13 600 1 390 4 800 7 500 FJ-4016 MFJ-4016 - - - - - - - 34 43

47 16 2.5 25 700 2 620 24 900 2 540 1 800 3 000 - - F-4016 MF-4016 - - - - - 48 56
47 20 1.0 23 500 2 400 18 500 1 890 4 800 7 500 FJ-4020 MFJ-4020 - - FIR-354020 35 20.5 39 0.6 46 51
47 20 2.5 32 500 3 350 34 000 3 450 1 800 3 000 - - F-4020 MF-4020 FIR-354020 35 20.5 39 0.6 60 69
47 26 1.0 31 500 3 200 26 900 2 740 4 800 7 500 FJ-4026 MFJ-4026 - - FIR-354026 35 26.5 39 0.6 60 65
45 52 16 1.0 19 900 2 030 15 400 1 570 4 300 6 700 FJ-4516 MFJ-4516 - - - - - - - 39 50

52 16 2.5 27 300 2 790 27 800 2 840 1 600 2 600 - - F-4516 MF-4516 - - - - - 53 64
52 20 1.0 25 500 2 600 21 200 2 160 4 300 6 700 FJ-4520 MFJ-4520 - - FIR-404520 40 20.5 44 0.6 53 59
52 20 2.5 35 000 3 550 38 500 3 900 1 600 2 600 - - F-4520 MF-4520 FIR-404520 40 20.5 44 0.6 67 78
50 58 20 1.1 28 900 2 940 23 100 2 350 3 800 6 300 FJ-5020L MFJ-5020 - - FIR-455020 45 20.5 49 0.6 56 71
58 20 2.8 39 500 4 050 41 500 4 250 1 700 2 800 - - F-5020 MF-5020 - - - - - 81 95
58 24 1.1 36 000 3 700 30 500 3 150 3 800 6 300 FJ-5024 MFJ-5024 - - - - - - - 69 84
58 24 2.8 48 000 4 900 53 000 5 400 1 700 2 800 - - F-5024 MF-5024 - - - - - 98 110
55 63 20 1.1 30 000 3 100 25 100 2 560 3 400 5 600 FJ-5520 MFJ-5520 - - - - - - - 60 79

63 20 2.8 41 500 4 250 45 500 4 650 1 600 2 400 - - F-5520 MF-5520 - - - - - 88 105
63 24 1.1 37 500 3 850 33 500 3 400 3 400 5 600 FJ-5524 MFJ-5524 - - - - - - - 72 90
63 24 2.8 50 500 5 150 58 000 5 950 1 600 2 400 - - F-5524 MF-5524 - - - - - 105 125
B 262 B 263
B244-279E.indd 262-263 11/20/13 4:59:51 PM

SOLID NEEDLE ROLLER BEARINGS
RLM LM
RNA NA
Inscribed Circle Diameter 9 22 mm B
C C C C
r r ra
r r
r r ra
B
jD jFw jD jFw jD jd jD jd jDa jda
Without Inner Ring With Inner Ring

RLM RNA LM NA
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers Boundary Dimensions Abutment and Fillet Dimensions Mass
(mm) (N) {kgf} (min1) (mm) (mm) (kg)
Without Inner Ring Without Inner Ring With Inner Ring
FW D C r Cr C 0r Cr C 0r Grease Oil d B da Da ra approx.
min. min. max. max. Without Inner Ring With Inner Ring
9 16 12 0.3 6 150 5 400 625 550 24 000 40 000 RLM 912 LM 91612-1 6 12 8 14 0.3 0.009 0.013
16 16 0.3 7 900 7 450 805 760 24 000 40 000 RLM 916 14 0.3 0.011 .
10 17 10 0.3 5 350 4 650 545 470 22 000 36 000 RLM 101710 15 0.3 0.008 .
17 15 0.3 8 050 7 800 820 795 22 000 36 000 RLM 101715 15 0.3 0.012 .
12 17 12 0.3 6 150 7 650 625 780 18 000 30 000 RLM 1212 LM 1212 8 12.2 10 15 0.3 0.007 0.013
19 12 0.3 7 300 7 150 745 730 18 000 30 000 RLM 121912 LM 121912 8 12.2 10 17 0.3 0.011 0.017
14 22 13 0.3 9 150 9 950 930 1 010 20 000 32 000 RNA 4900 NA 4900 10 13 12 20 0.3 0.016 0.024
22 16 0.3 12 100 12 700 1 230 1 300 15 000 24 000 RLM 1416 LM 1416 10 16.2 12 20 0.3 0.019 0.028
22 20 0.3 15 500 17 500 1 580 1 790 15 000 24 000 RLM 1420 LM 1420 10 20.2 12 20 0.3 0.024 0.036
15 20 15 0.3 8 100 11 700 825 1 190 14 000 24 000 RLM 1515 LM 1515 10 15.2 12 18 0.3 0.011 0.022
20 20 0.3 11 100 17 400 1 130 1 770 14 000 24 000 RLM 1520 LM 1520 10 20.2 12 18 0.3 0.015 0.03
22 15 0.3 9 900 11 100 1 010 1 140 14 000 24 000 RLM 152215 LM 152215 10 15.2 12 20 0.3 0.016 0.027
16 24 13 0.3 10 100 11 700 1 030 1 190 17 000 28 000 RNA 4901 NA 4901 12 13 14 22 0.3 0.018 0.027
24 16 0.3 12 900 14 200 1 310 1 450 13 000 22 000 RLM 1616 LM 1616 12 16.2 14 22 0.3 0.021 0.032
24 20 0.3 16 500 19 500 1 680 1 990 13 000 22 000 RLM 1620 LM 1620 12 20.2 14 22 0.3 0.027 0.041
24 22 0.3 17 900 24 500 1 830 2 500 17 000 28 000 RNA 6901 NA 6901 12 22 14 22 0.3 0.03 0.045
17 22 10 0.3 5 850 7 950 595 810 13 000 20 000 RLM 1710 LM 1710 12 10.2 14 20 0.3 0.008 0.017
24 25 0.5 18 200 25 300 1 850 2 580 13 000 20 000 RLM 172425 LM 172425 12 25.2 16 20 0.5 0.03 0.052
18 25 15 0.5 11 500 14 300 1 170 1 450 12 000 20 000 RLM 1815 LM 1815 15 15.2 19 21 0.5 0.019 0.028
25 20 0.5 15 800 21 500 1 610 2 190 12 000 20 000 RLM 1820 LM 1820 15 20.2 19 21 0.5 0.025 0.037
20 27 10 0.5 7 950 9 150 810 930 11 000 18 000 RLM 2010 LM 2010 15 10.2 19 23 0.5 0.014 0.025
27 15 0.5 11 900 15 400 1 220 1 570 11 000 18 000 RLM 2015 LM 2015 15 15.2 19 23 0.5 0.021 0.037
27 20 0.5 16 400 23 200 1 670 2 370 11 000 18 000 RLM 2020 LM 2020 15 20.2 19 23 0.5 0.028 0.049
27 25 0.5 19 800 29 500 2 010 3 000 11 000 18 000 RLM 2025 LM 2025 15 25.2 19 23 0.5 0.035 0.061
28 13 0.3 10 800 13 600 1 100 1 390 13 000 22 000 RNA 4902 NA 4902 15 13 17 26 0.3 0.021 0.035
28 18 0.3 15 700 21 900 1 600 2 240 13 000 22 000 RNA 5902 NA 5902 15 18 17 26 0.3 0.032 0.051
28 23 0.3 19 300 28 600 1 960 2 920 13 000 22 000 RNA 6902 NA 6902 15 23 17 26 0.3 0.039 0.064
22 29 20 0.5 17 700 26 400 1 810 2 690 10 000 16 000 RLM 2220 LM 2220 17 20.2 21 25 0.5 0.03 0.054
29 25 0.5 21 300 33 500 2 170 3 400 10 000 16 000 RLM 2225 LM 2225 17 25.2 21 25 0.5 0.038 0.068
30 13 0.3 11 600 15 400 1 190 1 570 12 000 20 000 RNA 4903 NA 4903 17 13 19 28 0.3 0.023 0.038
30 18 0.3 16 800 24 800 1 720 2 530 12 000 20 000 RNA 5903 NA 5903 17 18 19 28 0.3 0.034 0.055
30 20 0.5 20 000 27 200 2 030 2 780 10 000 16 000 RLM 223020 LM 223020 17 20.2 21 26 0.5 0.035 0.06
30 23 0.3 20 700 32 500 2 110 3 300 12 000 20 000 RNA 6903 NA 6903 17 23 19 28 0.3 0.041 0.068
Remarks If a full complement roller bearing is required, please contact NSK.
B 264 B 265
B244-279E.indd 264-265 11/20/13 4:59:52 PM

RLM LM
RNA NA
C C C C
r r ra
r r
r r ra
B

RLM RNA LM NA
25 32 12 0.5 10 300 13 700 1 050 1 400 8 500 14 000 RLM 2512 LM 2512 20 12.2 24 28 0.5 0.02 0.036
32 20 0.5 18 800 29 700 1 920 3 050 8 500 14 000 RLM 2520 LM 2520 20 20.2 24 28 0.5 0.034 0.061
32 25 0.5 22 700 37 500 2 310 3 850 8 500 14 000 RLM 2525 LM 2525 20 25.2 24 28 0.5 0.042 0.076
37 17 0.3 19 700 22 900 2 010 2 340 11 000 18 000 RNA 4904 NA 4904 20 17 22 35 0.3 0.055 0.077
37 23 0.3 27 800 35 500 2 830 3 650 11 000 18 000 RNA 5904 NA 5904 20 23 22 35 0.3 0.089 0.12
37 30 0.3 36 500 50 500 3 700 5 150 11 000 18 000 RNA 6904 NA 6904 20 30 22 35 0.3 0.098 0.14
28 35 20 0.5 19 900 33 000 2 030 3 350 7 500 12 000 RLM 2820 LM 2820 22 20.2 26 31 0.5 0.038 0.062
35 25 0.5 23 900 42 000 2 440 4 250 7 500 12 000 RLM 2825 LM 2825 22 25.2 26 31 0.5 0.047 0.092
37 30 0.5 34 000 52 500 3 450 5 350 7 500 12 000 RLM 283730 LM 283730 22 30.2 26 33 0.5 0.075 0.13
39 17 0.3 22 400 30 500 2 290 3 150 9 500 15 000 RNA 49/22 NA 49/22 22 17 24 37 0.3 0.056 0.086
39 23 0.3 28 300 41 500 2 890 4 200 9 500 15 000 RNA 59/22 NA 59/22 22 23 24 37 0.3 0.091 0.135
39 30 0.3 37 000 58 500 3 800 6 000 9 500 15 000 RNA 69/22 NA 69/22 22 30 24 37 0.3 0.096 0.15
30 37 25 0.5 24 500 44 000 2 490 4 500 7 100 12 000 RLM 3025 LM 3025 25 25.2 29 33 0.5 0.05 0.092
40 20 0.5 25 000 36 000 2 550 3 650 7 100 12 000 RLM 304020 LM 304020 25 20.2 29 36 0.5 0.06 0.093
40 30 0.5 35 000 56 000 3 600 5 700 7 100 12 000 RLM 304030 LM 304030 25 30.2 29 36 0.5 0.09 0.14
42 17 0.3 21 400 26 800 2 180 2 740 9 000 14 000 RNA 4905 NA 4905 25 17 27 40 0.3 0.063 0.091
42 23 0.3 30 000 41 500 3 100 4 250 9 000 14 000 RNA 5905 NA 5905 25 23 27 40 0.3 0.10 0.14
42 30 0.3 39 500 59 000 4 050 6 050 9 000 14 000 RNA 6905 NA 6905 25 30 27 40 0.3 0.11 0.16
32 42 20 0.5 25 800 38 000 2 630 3 900 6 700 11 000 RLM 3220 LM 3220 28 20.2 32 38 0.5 0.064 0.09
42 30 0.5 36 500 59 000 3 700 6 050 6 700 11 000 RLM 3230 LM 3230 28 30.2 32 38 0.5 0.096 0.14
45 17 0.3 22 200 28 700 2 270 2 930 8 500 13 000 RNA 49/28 NA 49/28 28 17 30 43 0.3 0.076 0.099
45 23 0.3 31 500 44 500 3 200 4 550 8 500 13 000 RNA 59/28 NA 59/28 28 23 30 43 0.3 0.11 0.145
45 30 0.3 41 000 63 500 4 200 6 450 8 500 13 000 RNA 69/28 NA 69/28 28 30 30 43 0.3 0.13 0.175
35 42 20 0.5 22 300 41 000 2 270 4 200 6 300 10 000 RLM 3520 LM 3520 30 20.2 34 38 0.5 0.046 0.085
42 30 0.5 31 000 63 500 3 200 6 450 6 300 10 000 RLM 3530 LM 3530 30 30.2 34 38 0.5 0.07 0.13
45 20 0.5 27 500 42 500 2 800 4 350 6 300 10 000 RLM 354520 LM 354520 30 20.2 34 41 0.5 0.069 0.11
45 25 0.5 33 000 54 500 3 400 5 550 6 300 10 000 RLM 354525 LM 354525 30 25.2 34 41 0.5 0.086 0.135
45 30 0.5 38 500 66 000 3 950 6 750 6 300 10 000 RLM 354530 LM 354530 30 30.2 34 41 0.5 0.10 0.16
47 17 0.3 23 900 32 500 2 430 3 300 7 500 12 000 RNA 4906 NA 4906 30 17 32 45 0.3 0.072 0.105
47 23 0.3 33 500 50 500 3 450 5 150 7 500 12 000 RNA 5906 NA 5906 30 23 32 45 0.3 0.11 0.15
47 30 0.3 44 000 71 500 4 500 7 300 7 500 12 000 RNA 6906 NA 6906 30 30 32 45 0.3 0.13 0.19
B 266 B 267
B244-279E.indd 266-267 11/20/13 4:59:53 PM

RLM LM
RNA NA
C C C C
r r ra
r r
r r ra
B

RLM RNA LM NA
37 47 20 0.6 28 200 45 000 2 880 4 550 6 000 9 500 RLM 3720 LM 3720 32 20.3 36 43 0.6 0.072 0.115
47 30 0.6 39 500 69 500 4 050 7 100 6 000 9 500 RLM 3730 LM 3730 32 30.3 36 43 0.6 0.11 0.17
38 48 20 0.6 29 000 47 000 2 960 4 800 5 600 9 000 RLM 3820 LM 3820 32 20.3 36 44 0.6 0.074 0.125
48 30 0.6 41 000 73 000 4 150 7 450 5 600 9 000 RLM 3830 LM 3830 32 30.3 36 44 0.6 0.11 0.195
40 50 20 0.6 29 700 49 000 3 050 5 000 5 300 9 000 RLM 4020 LM 4020 35 20.3 39 46 0.6 0.078 0.125
50 30 0.6 42 000 76 500 4 250 7 800 5 300 9 000 RLM 4030 LM 4030 35 30.3 39 46 0.6 0.12 0.19
52 20 0.6 29 900 45 000 3 050 4 600 6 700 10 000 RNA 49/32 NA 49/32 32 20 36 48 0.6 0.092 0.16
52 27 0.6 40 500 66 000 4 100 6 750 6 700 10 000 RNA 59/32 NA 59/32 32 27 36 48 0.6 0.15 0.24
52 36 0.6 56 000 101 000 5 700 10 300 6 700 10 000 RNA 69/32 NA 69/32 32 36 36 48 0.6 0.17 0.29
42 55 20 0.6 30 500 47 500 3 100 4 800 6 300 10 000 RNA 4907 NA 4907 35 20 39 51 0.6 0.11 0.17
55 27 0.6 41 500 69 500 4 200 7 100 6 300 10 000 RNA 5907 NA 5907 35 27 39 51 0.6 0.175 0.25
55 36 0.6 57 500 106 000 5 850 10 900 6 300 10 000 RNA 6907 NA 6907 35 36 39 51 0.6 0.20 0.315
45 55 20 0.6 31 000 53 500 3 150 5 500 4 800 8 000 RLM 4520 LM 4520 40 20.3 44 51 0.6 0.086 0.14
55 30 0.6 43 500 83 500 4 450 8 500 4 800 8 000 RLM 4530 LM 4530 40 30.3 44 51 0.6 0.13 0.21
48 62 22 0.6 39 000 61 500 3 950 6 300 5 600 9 000 RNA 4908 NA 4908 40 22 44 58 0.6 0.15 0.24
62 30 0.6 54 500 95 000 5 550 9 700 5 600 9 000 RNA 5908 NA 5908 40 30 44 58 0.6 0.23 0.355
62 40 0.6 72 000 137 000 7 350 13 900 5 600 9 000 RNA 6908 NA 6908 40 40 44 58 0.6 0.265 0.435
50 62 20 0.6 35 500 60 500 3 600 6 150 4 300 7 100 RLM 506220 LM 506220 42 20.3 46 58 0.6 0.12 0.21
62 25 0.6 43 000 77 500 4 400 7 900 4 300 7 100 RLM 506225 LM 506225 42 25.3 46 58 0.6 0.155 0.265
52 68 22 0.6 41 000 67 500 4 150 6 900 5 000 8 000 RNA 4909 NA 4909 45 22 49 64 0.6 0.19 0.28
68 30 0.6 57 000 104 000 5 800 10 600 5 000 8 000 RNA 5909 NA 5909 45 30 49 64 0.6 0.27 0.39
68 40 0.6 76 000 149 000 7 750 15 200 5 000 8 000 RNA 6909 NA 6909 45 40 49 64 0.6 0.335 0.495
55 65 30 0.6 49 000 104 000 5 000 10 600 4 000 6 300 RLM 5530 LM 5530 45 30.3 49 61 0.6 0.16 0.34
67 20 0.6 38 000 68 000 3 850 6 900 4 000 6 300 RLM 556720 LM 556720 45 20.3 49 63 0.6 0.13 0.25
58 72 22 0.6 42 500 73 500 4 350 7 500 4 500 7 100 RNA 4910 NA 4910 50 22 54 68 0.6 0.18 0.295
72 30 0.6 59 500 113 000 6 050 11 500 4 500 7 100 RNA 5910 NA 5910 50 30 54 68 0.6 0.25 0.405
72 40 0.6 79 000 163 000 8 050 16 600 4 500 7 100 RNA 6910 NA 6910 50 40 54 68 0.6 0.32 0.53
B 268 B 269
B244-279E.indd 268-269 11/20/13 4:59:54 PM

RNA NA
C C
r r ra
r ra
B
jD jFw jD jd jDa jda

RNA NA
63 80 25 1 53 500 87 500 5 450 8 950 4 000 6 700 RNA 4911 NA 4911 55 25 60 75 1 0.26 0.40
80 34 1 73 500 133 000 7 500 13 600 4 000 6 700 RNA 5911 NA 5911 55 34 60 75 1 0.37 0.56
80 45 1 93 500 181 000 9 550 18 500 4 000 6 700 RNA 6911 NA 6911 55 45 60 75 1 0.475 0.73
68 85 25 1 56 000 95 500 5 700 9 750 3 800 6 300 RNA 4912 NA 4912 60 25 65 80 1 0.28 0.435
85 34 1 77 500 145 000 7 900 14 800 3 800 6 300 RNA 5912 NA 5912 60 34 65 80 1 0.415 0.625
85 45 1 98 000 197 000 10 000 20 100 3 800 6 300 RNA 6912 NA 6912 60 45 65 80 1 0.485 0.76
72 90 25 1 58 500 103 000 5 950 10 500 3 600 5 600 RNA 4913 NA 4913 65 25 70 85 1 0.32 0.465
90 34 1 81 000 157 000 8 250 16 000 3 600 5 600 RNA 5913 NA 5913 65 34 70 85 1 0.48 0.675
90 45 1 103 000 213 000 10 500 21 800 3 600 5 600 RNA 6913 NA 6913 65 45 70 85 1 0.53 0.79
80 100 30 1 80 500 143 000 8 200 14 600 3 200 5 300 RNA 4914 NA 4914 70 30 75 95 1 0.47 0.74
100 40 1 107 000 206 000 10 900 21 000 3 200 5 300 RNA 5914 NA 5914 70 40 75 95 1 0.69 1.05
100 54 1 143 000 298 000 14 500 30 500 3 200 5 300 RNA 6914 NA 6914 70 54 75 95 1 0.89 1.4
85 105 30 1 84 000 155 000 8 600 15 800 3 000 5 000 RNA 4915 NA 4915 75 30 80 100 1 0.5 0.79
105 40 1 112 000 222 000 11 400 22 700 3 000 5 000 RNA 5915 NA 5915 75 40 80 100 1 0.735 1.1
105 54 1 149 000 325 000 15 200 33 000 3 000 5 000 RNA 6915 NA 6915 75 54 80 100 1 0.96 1.5
90 110 30 1 87 500 166 000 8 950 17 000 2 800 4 500 RNA 4916 NA 4916 80 30 85 105 1 0.53 0.835
110 40 1 116 000 239 000 11 900 24 400 2 800 4 500 RNA 5916 NA 5916 80 40 85 105 1 0.75 1.15
110 54 1 157 000 350 000 16 000 36 000 2 800 4 500 RNA 6916 NA 6916 80 54 85 105 1 0.99 1.55
100 120 35 1.1 104 000 214 000 10 600 21 800 2 600 4 000 RNA 4917 NA 4917 85 35 91.5 113.5 1 0.68 1.25
120 46 1.1 138 000 310 000 14 100 31 500 2 600 4 000 RNA 5917 NA 5917 85 46 91.5 113.5 1 0.99 1.75
120 63 1.1 174 000 415 000 17 800 42 500 2 600 4 000 RNA 6917 NA 6917 85 63 91.5 113.5 1 1.2 2.25
105 125 35 1.1 108 000 228 000 11 000 23 300 2 400 4 000 RNA 4918 NA 4918 90 35 96.5 118.5 1 0.72 1.35
125 46 1.1 143 000 330 000 14 600 33 500 2 400 4 000 RNA 5918 NA 5918 90 46 96.5 118.5 1 1.05 1.85
125 63 1.1 181 000 445 000 18 400 45 000 2 400 4 000 RNA 6918 NA 6918 90 63 96.5 118.5 1 1.35 2.45
110 130 35 1.1 111 000 242 000 11 400 24 700 2 200 3 800 RNA 4919 NA 4919 95 35 101.5 123.5 1 0.74 1.4
130 46 1.1 148 000 350 000 15 100 35 500 2 200 3 800 RNA 5919 NA 5919 95 46 101.5 123.5 1 1.15 2.0
130 63 1.1 187 000 470 000 19 100 48 000 2 200 3 800 RNA 6919 NA 6919 95 63 101.5 123.5 1 1.5 2.65
115 140 40 1.1 144 000 295 000 14 700 30 000 2 200 3 600 RNA 4920 NA 4920 100 40 106.5 133.5 1 1.15 1.95
140 54 1.1 193 000 430 000 19 700 43 500 2 200 3 600 RNA 5920 NA 5920 100 54 106.5 133.5 1 1.8 2.85
120 140 30 1 99 500 214 000 10 100 21 900 2 000 3 400 RNA 4822 NA 4822 110 30 115 135 1 0.67 1.1
B 270 B 271
B244-279E.indd 270-271 11/20/13 4:59:55 PM

RNA NA
C C
r r ra
r ra
B
jD jFw jD jd jDa jda

RNA NA
125 150 40 1.1 149 000 315 000 15 200 32 500 2 000 3 200 RNA 4922 NA 4922 110 40 116.5 143.5 1 1.25 2.1
150 54 1.1 200 000 460 000 20 300 47 000 2 000 3 200 RNA 5922 NA 5922 110 54 116.5 143.5 1 1.95 3.05
130 150 30 1 105 000 238 000 10 700 24 300 1 900 3 200 RNA 4824 NA 4824 120 30 125 145 1 0.71 1.15
135 165 45 1.1 192 000 395 000 19 600 40 500 1 900 3 000 RNA 4924 NA 4924 120 45 126.5 158.5 1 1.9 2.9
165 60 1.1 253 000 565 000 25 800 58 000 1 900 3 000 RNA 5924 NA 5924 120 60 126.5 158.5 1 2.7 4.05
145 165 35 1.1 127 000 315 000 12 900 32 000 1 700 2 800 RNA 4826 NA 4826 130 35 136.5 158.5 1 0.92 1.8
150 180 50 1.5 228 000 515 000 23 200 52 500 1 700 2 800 RNA 4926 NA 4926 130 50 138 172 1.5 2.3 4.0
180 67 1.5 299 000 725 000 30 500 74 000 1 700 2 800 RNA 5926 NA 5926 130 67 138 172 1.5 3.3 5.55
155 175 35 1.1 133 000 340 000 13 600 35 000 1 600 2 600 RNA 4828 NA 4828 140 35 146.5 168.5 1 0.98 1.9
160 190 50 1.5 235 000 545 000 24 000 55 500 1 600 2 600 RNA 4928 NA 4928 140 50 148 182 1.5 2.45 4.25
190 67 1.5 310 000 775 000 31 500 79 000 1 600 2 600 RNA 5928 NA 5928 140 67 148 182 1.5 3.55 6.0
165 190 40 1.1 180 000 440 000 18 300 45 000 1 500 2 400 RNA 4830 NA 4830 150 40 156.5 183.5 1 1.6 2.75
175 200 40 1.1 184 000 465 000 18 700 47 000 1 400 2 200 RNA 4832 NA 4832 160 40 166.5 193.5 1 1.75 2.95
185 215 45 1.1 224 000 540 000 22 900 55 000 1 400 2 200 RNA 4834 NA 4834 170 45 176.5 208.5 1 2.55 4.0
195 225 45 1.1 230 000 570 000 23 500 58 000 1 300 2 000 RNA 4836 NA 4836 180 45 186.5 218.5 1 2.65 4.2
210 240 50 1.5 268 000 705 000 27 300 72 000 1 200 1 900 RNA 4838 NA 4838 190 50 198 232 1.5 3.2 5.6
220 250 50 1.5 274 000 740 000 27 900 75 500 1 100 1 800 RNA 4840 NA 4840 200 50 208 242 1.5 3.35 5.9
240 270 50 1.5 286 000 805 000 29 100 82 000 1 000 1 700 RNA 4844 NA 4844 220 50 228 262 1.5 3.65 6.45
265 300 60 2 375 000 1 070 000 38 500 109 000 950 1 500 RNA 4848 NA 4848 240 60 249 291 2 5.45 10
285 320 60 2 395 000 1 160 000 40 000 118 000 900 1 400 RNA 4852 NA 4852 260 60 269 311 2 5.9 11
305 350 69 2 510 000 1 390 000 52 000 142 000 800 1 300 RNA 4856 NA 4856 280 69 289 341 2 9.5 15.5
330 380 80 2.1 660 000 1 810 000 67 500 185 000 750 1 200 RNA 4860 NA 4860 300 80 311 369 2 13 22
350 400 80 2.1 675 000 1 900 000 69 000 194 000 710 1 100 RNA 4864 NA 4864 320 80 331 389 2 13.5 23.5
370 420 80 2.1 690 000 1 990 000 70 500 203 000 670 1 100 RNA 4868 NA 4868 340 80 351 409 2 14 24.5
390 440 80 2.1 705 000 2 080 000 72 000 212 000 630 1 000 RNA 4872 NA 4872 360 80 371 429 2 15 26
B 272 B 273
B244-279E.indd 272-273 11/20/13 4:59:56 PM

THRUST NEEDLE ROLLER BEARINGS
FNTA (Thrust Cage & Needle Roller Assemblies)
jDW 00.005 s
Thrust raceway washers
FTRA (s=1.0)
FTRB (s=1.5)
FTRC (s=2.0)
FTRD (s=2.5)
FTRE (s=3.0)
Bore Diameter 10 100 mm jDC
(1)
jDC1 (1)
E11

jD P 0.25
0.75 jD P1 ++ 0.30
0.05 jDi jD e
C12
FNTA FTRA FTRB FTRC FTRD FTRE
Boundary Dimensions Basic Load Ratings Bearing Numbers of Matching Bearing Rings Roller Contact Surfaces Mass
Limiting Speeds (g)
(mm) (N) {kgf} (mm)
(min1) Bearing Numbers 0 0 0 0 Outside Diameter Bore Diameter
D c1,D p1 D c,D p D W Ca C 0a Ca C 0a Oil s =1.0 0.05 s =1.5 0.08
s =2.0 0.08
s =2.5 0.08
s =3.0 0.08
De Di approx.
min. max. FNTA FTRA
10 24 2 7 750 23 000 790 2 350 17 000 FNTA-1024 *FTRA-1024 FTRB-1024 FTRC-1024 22.0 11.5 2.3 2.9
12 26 2 8 350 26 300 855 2 680 16 000 FNTA-1226 FTRA-1226 FTRB-1226 FTRC-1226 24.0 13.5 3.4 3.3
15 28 2 7 950 25 800 810 2 630 15 000 FNTA-1528 FTRA-1528 FTRB-1528 FTRC-1528 FTRD-1528 FTRE-1528 26.0 16.5 3.5 3.5
18 31 2 8 600 29 700 875 3 050 13 000 FNTA-1831 FTRA-1831 FTRB-1831 FTRC-1831 FTRD-1831 FTRE-1831 29.0 19.5 4 3.9
20 35 2 11 900 47 000 1 220 4 800 12 000 FNTA-2035 FTRA-2035 FTRB-2035 FTRC-2035 FTRD-2035 FTRE-2035 33.0 21.5 5.4 5.1
25 42 2 14 800 66 000 1 510 6 750 9 500 FNTA-2542 FTRA-2542 FTRB-2542 FTRC-2542 FTRD-2542 FTRE-2542 40.0 26.5 7.7 7
40 60 3 26 900 122 000 2 740 12 400 6 700 FNTA-4060 FTRA-4060 FTRB-4060 FTRC-4060 FTRD-4060 FTRE-4060 57.0 42.0 18 12
Note (1) For tolerance classes C12 and E11, please refer to ISO 286 -1 and 286 -2 (ISO system of limits and fits), respectively.
(*) The tolerance of this bearing bore diameter is +0.025 to +0.175mm and outside diameter tolerance is
0.040 to 0.370mm
B 274 B 275
B244-279E.indd 274-275 11/20/13 4:59:57 PM

CAM FOLLOWERS
FCR (Full Complement)
FCRS Full Complement, Sealed
With Thrust Washer B1
FCJ (With Cage) B3
C
Sealed, with Cage and jM2 0
jF
FCJS 0. 25
Thrust Washer G1 B4
jM1 jM1
Outside Diameter 16 90 mm E
jd
jD G jd 1 00. 05
X
r B2
Full Complement, Full Complement, Full Complement, ra ( 4 )
Full Complement Sealed With Hexagonal Socket With Eccentric Bush
With Thrust Washer
FCR FCRS FCRB FCRE
Boundary Dimensions Dimensions Bearing Numbers Basic Dynamic Load Ratings Limiting Loads Limiting Track Loads Mass Dimensions of Eccentric Bush Dimensions (3) Shoulder Tightening Torque
(mm) (mm) (N) {kgf} (N) {kgf} (N) {kgf} (kg) Hexagonal Socket (mm) Dimensions (Ncm) {kgfcm}
Screw (2)(width (mm)
D C d G G1 B1 B2 B3 M2 M1 r FCR FCRS Cr P max across flats) B4 d1 E F
FCJ FCJS (mm)
min. approx. (min.) (max.) (max.)
X
16 11 6 M 61 8 28 16 4( ) 1 0.3 FCR-16 FCRS-16 5 800 590 2 360 240 3 350 340 0.020 4 8 9 0.5 11 226 23
11 6 M 61 8 28 16 4( 1) 0.3 FCJ-16 FCJS-16 2 830 288 2 360 240 3 350 340 0.018 4 8 9 0.5 11 226 23
19 11 8 M 81.25 10 32 20 4( 1) 0.3 FCR-19 FCRS-19 6 600 670 4 200 425 4 150 425 0.031 4 10 11 0.5 13 550 56
11 8 M 81.25 10 32 20 4( 1) 0.3 FCJ-19 FCJS-19 3 450 355 4 200 425 4 150 425 0.030 4 10 11 0.5 13 550 56
22 12 10 M101.25 12 36 23 4( 1) 0.3 FCR-22 FCRS-22 8 550 875 6 550 665 5 300 540 0.047 5 11 13 0.5 15 1 060 108
12 10 M101.25 12 36 23 4( 1) 0.3 FCJ-22 FCJS-22 4 350 445 6 550 665 5 300 540 0.045 5 11 13 0.5 15 1 060 108
26 12 10 M101.25 12 36 23 4( 1) 0.3 FCR-26 FCRS-26 8 550 875 6 550 665 6 000 610 0.060 5 11 13 0.5 15 1 060 108
12 10 M101.25 12 36 23 4( 1) 0.3 FCJ-26 FCJS-26 4 350 445 6 550 665 6 000 610 0.058 5 11 13 0.5 15 1 060 108
30 14 12 M121.5 13 40 25 6 3 6 0.6 FCR-30 FCRS-30 12 500 1 280 9 250 945 7 800 795 0.088 6 12 17 1 20 1 450 148
14 12 M121.5 13 40 25 6 3 6 0.6 FCJ-30 FCJS-30 7 200 735 9 250 945 7 800 795 0.086 6 12 17 1 20 1 450 148
32 14 12 M121.5 13 40 25 6 3 6 0.6 FCR-32 FCRS-32 12 500 1 280 9 250 945 8 050 820 0.099 6 12 17 1 20 1 450 148
14 12 M121.5 13 40 25 6 3 6 0.6 FCJ-32 FCJS-32 7 200 735 9 250 945 8 050 820 0.096 6 12 17 1 20 1 450 148
35 18 16 M161.5 17 52 32.5 8 3 6 0.6 FCR-35 FCRS-35 18 600 1 900 17 000 1 740 11 800 1 200 0.17 10 15.5 22 1 24 4 000 410
18 16 M161.5 17 52 32.5 8 3 6 0.6 FCJ-35 FCJS-35 9 700 990 17 000 1 740 11 800 1 200 0.165 10 15.5 22 1 24 4 000 410
40 20 18 M181.5 19 58 36.5 8 3 6 1 FCR-40 FCRS-40 20 500 2 090 21 700 2 220 14 300 1 460 0.25 10 17.5 24 1 26 5 950 605
20 18 M181.5 19 58 36.5 8 3 6 1 FCJ-40 FCJS-40 10 300 1 050 21 700 2 220 14 300 1 460 0.24 10 17.5 24 1 26 5 950 605
47 24 20 M201.5 21 66 40.5 9 4 8 1 FCR-47 FCRS-47 28 200 2 880 26 400 2 690 20 800 2 120 0.39 12 19.5 27 1 31 8 450 860
24 20 M201.5 21 66 40.5 9 4 8 1 FCJ-47 FCJS-47 19 200 1 950 26 400 2 690 20 800 2 120 0.38 12 19.5 27 1 31 8 450 860
52 24 20 M201.5 21 66 40.5 9 4 8 1 FCR-52 FCRS-52 28 200 2 880 26 400 2 690 22 900 2 340 0.47 12 19.5 27 1 31 8 450 860
24 20 M201.5 21 66 40.5 9 4 8 1 FCJ-52 FCJS-52 19 200 1 950 26 400 2 690 22 900 2 340 0.455 12 19.5 27 1 31 8 450 860
62 29 24 M241.5 25 80 49.5 11 4 8 1 FCR-62 FCRS-62 40 000 4 100 38 500 3 950 34 000 3 450 0.80 14 24.5 34 1 45 15 200 1 550
29 24 M241.5 25 80 49.5 11 4 8 1 FCJ-62 FCJS-62 24 900 2 540 38 500 3 950 34 000 3 450 0.79 14 24.5 34 1 45 15 200 1 550
72 29 24 M241.5 25 80 49.5 11 4 8 1 FCR-72 FCRS-72 40 000 4 100 38 500 3 950 38 000 3 860 1.05 14 24.5 34 1 45 15 200 1 550
29 24 M241.5 25 80 49.5 11 4 8 1 FCJ-72 FCJS-72 24 900 2 540 38 500 3 950 38 000 3 860 1.05 14 24.5 34 1 45 15 200 1 550
80 35 30 M301.5 32 100 63 15 4 8 1 FCR-80 FCRS-80 60 500 6 200 61 000 6 200 52 000 5 300 1.55 17 31 40 1.5 52 30 500 3 120
35 30 M301.5 32 100 63 15 4 8 1 FCJ-80 FCJS-80 39 000 4 000 61 000 6 200 52 000 5 300 1.55 17 31 40 1.5 52 30 500 3 120
85 35 30 M301.5 32 100 63 15 4 8 1 FCR-85 FCRS-85 60 500 6 200 61 000 6 200 55 500 5 650 1.75 17 31 40 1.5 52 30 500 3 120
35 30 M301.5 32 100 63 15 4 8 1 FCJ-85 FCJS-85 39 000 4 000 61 000 6 200 55 500 5 650 1.75 17 31 40 1.5 52 30 500 3 120
90 35 30 M301.5 32 100 63 15 4 8 1 FCR-90 FCRS-90 60 500 6 200 61 000 6 200 59 000 6 000 1.95 17 31 40 1.5 52 30 500 3 120
35 30 M301.5 32 100 63 15 4 8 1 FCJ-90 FCJS-90 39 000 4 000 61 000 6 200 59 000 6 000 1.95 17 31 40 1.5 52 30 500 3 120
Notes (1) Only the head of the stud has on oil hole. Notes (3) Applicable to FCRE only.
(2) Applicable to FCRB only. (4) Should not be greater than r (min).
Remarks Standard grease is packed in sealed cam followers, but not in cam followers without seals.
B 276 B 277
B244-279E.indd 276-277 11/20/13 4:59:58 PM

ROLLER FOLLOWERS
FYCR (Full Complement)
FYCRS Full Complement, Sealed
with Thrust Washer
B B
FYCJ (With Cage) C C
FYCJS Sealed, with Cage and
Thrust Washer
jD jd jD jd jF
r r
Full Complement Full Complement, Sealed
with Thrust Washer
FYCR FYCRS
Boundary Dimensions Basic Load Ratings Limiting Track Loads Bearing Numbers Mass Shoulder
(mm) (N) {kgf} (N) {kgf} (kg) Dimensions
0 FYCR FYCRS (mm)
0.38
d D C B r Cr C 0r Cr C 0r FYCJ FYCJS F
min. approx. min.
5 16 11 12 0.3 5 800 8 000 590 815 3 350 340 FYCR-5 FYCRS-5 0.016 10
16 11 12 0.3 2 830 2 620 288 267 3 350 340 FYCJ-5 FYCJS-5 0.014 10
6 19 11 12 0.3 6 550 9 900 665 1 010 4 150 425 FYCR-6 FYCRS-6 0.022 12
19 11 12 0.3 3 450 3 600 355 365 4 150 425 FYCJ-6 FYCJS-6 0.020 12
8 24 14 15 0.3 10 100 15 000 1 030 1 530 6 500 665 FYCR-8 FYCRS-8 0.044 14
24 14 15 0.3 5 700 6 000 580 610 6 500 665 FYCJ-8 FYCJS-8 0.042 14
10 30 14 15 0.6 11 700 18 500 1 190 1 890 7 800 795 FYCR-10 FYCRS-10 0.069 17
30 14 15 0.6 6 950 8 200 705 835 7 800 795 FYCJ-10 FYCJS-10 0.067 17
12 32 14 15 0.6 12 600 21 000 1 280 2 140 8 050 820 FYCR-12 FYCRS-12 0.076 19
32 14 15 0.6 7 650 9 650 780 985 8 050 820 FYCJ-12 FYCJS-12 0.074 19
15 35 18 19 0.6 18 700 29 300 1 910 2 990 11 800 1 200 FYCR-15 FYCRS-15 0.105 23
35 18 19 0.6 12 200 14 100 1 250 1 440 11 800 1 200 FYCJ-15 FYCJS-15 0.097 23
17 40 20 21 0.6 21 100 35 000 2 160 3 600 14 300 1 460 FYCR-17 FYCRS-17 0.145 25
40 20 21 0.6 13 700 16 700 1 390 1 700 14 300 1 460 FYCJ-17 FYCJS-17 0.14 25
20 47 24 25 1 28 900 50 000 2 940 5 100 20 800 2 120 FYCR-20 FYCRS-20 0.255 29
47 24 25 1 18 200 22 600 1 850 2 310 20 800 2 120 FYCJ-20 FYCJS-20 0.245 29
25 52 24 25 1 32 500 60 000 3 300 6 100 22 900 2 340 FYCR-25 FYCRS-25 0.285 34
52 24 25 1 22 200 31 000 2 270 3 150 22 900 2 340 FYCJ-25 FYCJS-25 0.275 34
30 62 28 29 1 47 500 96 000 4 800 9 800 33 000 3 350 FYCR-30 FYCRS-30 0.48 51
62 28 29 1 31 500 47 000 3 200 4 800 33 000 3 350 FYCJ-30 FYCJS-30 0.47 51
35 72 28 29 1 49 500 106 000 5 050 10 800 36 500 3 700 FYCR-35 FYCRS-35 0.64 58
72 28 29 1 33 000 52 500 3 400 5 350 36 500 3 700 FYCJ-35 FYCJS-35 0.635 58
40 80 30 32 1 54 500 126 000 5 600 12 800 43 500 4 450 FYCR-40 FYCRS-40 0.88 66
80 30 32 1 38 500 67 500 3 950 6 900 43 500 4 450 FYCJ-40 FYCJS-40 0.865 66
45 85 30 32 1 57 500 139 000 5 850 14 100 46 500 4 750 FYCR-45 FYCRS-45 0.93 72
85 30 32 1 40 000 73 000 4 100 7 450 46 500 4 750 FYCJ-45 FYCJS-45 0.91 72
50 90 30 32 1 60 500 152 000 6 150 15 500 49 500 5 050 FYCR-50 FYCRS-50 0.995 76
90 30 32 1 41 500 78 000 4 200 7 950 49 500 5 050 FYCJ-50 FYCJS-50 0.965 76
Remarks Standard grease is packed in sealed cam followers, but not in cam followers without seals.
B 278 B 279
B244-279E.indd 278-279 11/20/13 4:59:59 PM

BALL BEARING UNITS
SET SCREW TYPE PILLOW BLOCKS CAST HOUSING
UCP2 Shaft Diameter 12 90mm B286
1/2 3 1/2 inch
SET SCREW TYPE FLANGED UNITS CAST HOUSING

UCF2 Shaft Diameter 12 90mm B292
1/2 3 1/2 inch
UCFL2 Shaft Diameter 12 90mm B298
1/2 3 1/2 inch
B 280 B 281
B280-303E.indd 280-281 11/20/13 5:00:41 PM

1. CONSTRUCTION 2. DESIGN FEATURES AND ADVANTAGES
The NSK bearing unit is a combination of a radial a slinger is provided on both sides. 2.1 MAINTENANCE FREE TYPE (5) Cases involving a heavy load of which the Cr/Pr
ball bearing, seal, and a housing of high-grade cast Depending on the type, the following methods of value is about 10 or below, and the speed is
iron or pressed steel, which comes in various shapes. fitting to the shaft are employed: The NSK Maintenance free bearing unit contains 10 min1 or below, or the movement is oscillatory.
The outer surface of the bearing and the internal (1) The inner ring is fastened onto the shaft in two a high-grade lithium-based grease, good for use over (6) Cases where the number of revolutions is
surface of the housing are spherical, so that the unit places by set screws. a long period, which is ideally suited to sealed-type relatively high and the noise problem has to be
is self-aligning. (2) The inner ring has a tapered bore and is fitted to bearing. Also provided is an excellent sealing device, considered; for example, when the bearing is used
The inside construction of the ball bearing for the shaft by means of an adapter. which prevents any leakage of grease or penetration with the fan of an air conditioner.
the unit is such that steel balls and retainers of the (3) In the eccentric locking collar system the of dust and water from outside.
same type as in series 62 and 63 of the deep groove inns ring is fastened to the shaft by means of It is designed so that the rotation of the shaft 2.3 SPECIAL SEALING FEATURE
ball bearing are used. A duplex seal consisting of a eccentrics grooves provided at the side of the causes the sealed-in grease to circulate through
the inside space, effectively providing maximum 2.3.1 STANDARD BEARING UNITS
combination of an oil-proof synthetic rubber seal and inner ring and on the collar. The sealing device of the ball bearing for the NSK
lubrication. The lubrication effect is maintained over a
long period with no need for replenishment of grease. bearing unit is a combination of a heat-resistant and
To summarize the advantages of the NSK oil-proof synthetic rubber seal and a slinger of an
maintenance free bearing unit: exclusive design.
(1) As an adequate amount of good quality grease is The seal, which is fixed in the outer ring, is
sealed in at the time of manufacture, there is no steel-reinforced, and its lip, in contact with the inner
need for replenishment. This means savings in ring, is designed to minimize frictional torque.
terms of time and maintenance costs. The slinger is fixed to the inner ring of the bearing
(2) Since there is no need for any regreasing facilities, with which it rotates. There is a small clearance
such as piping, a more compact design is between its periphery and the outer ring.
possible. There are triangular protrusions on the outside
(3) The sealed-in design eliminates the possibility face of the slinger and, as the bearing rotates, these
of grease leakage, which could lead to stained protrusions on the slinger create a flow of air outward
products. from the bearing. In this way, the slinger acts as a fan
which-keeps dust and water away from the bearing.
Grease fitting 2.2 RELUBRICATABLE TYPE These two types of seals on both sides of the
Housing bearing prevent grease leakage, and foreign matter is
Spherical outer ring
The NSK relubricatable type bearing unit has prevented from entering the bearing from outside.
an advantage over other similar, units being so
Slinger
designed as to permit regreasing even in the case
Special rubber seal
of misalignment of 2 to the right or left. The hole
through which the grease fitting is mounted usually
causes structural weakening of the housing.
However, as a result of extensive testing, in the
NSK bearing unit the hole is positioned so as
to minimize this adverse effect. In addition, the
regreasing groove has been designed to minimize
Ball end set screw
weakening of the housing.
While the NSK maintenance free type bearing
unit is satisfactory for use under normal operating
conditions in-doors, in the following circumstances
it is necessary to use the relubricatable type bearing
unit:
Relubricatable bearing unit
(1) Cases where the temperature of the bearing rises
above 100C, 212F:
*-Normal temperature of up to 130C, 266F
heat-resistant bearing units.
(2) Cases where there is excessive dust, but space
does not permit using a bearing unit with a cover.
(3) Cases where the bearing unit is constantly
exposed to splashes of water or any other liquid,
but space does not permit using a bearing unit
Maintenance free bearing unit with a cover.
(4) Cases in which the humidity is very high, and the
machine in which the bearing unit is used is run
Fig.1.1 only intermittently.
Fig.2.1
B 282 B 283
B280-303E.indd 282-283 11/20/13 5:00:42 PM

2.3.2 BEARING UNITS WITH COVERS 2.4 SECURE FITTING
The NSK bearing unit with a cover consists of a 3. RECOMMENDED TORQUES FOR TIGTENING SET SCREWS
Fastening the bearing to the shaft is effected by
standard bearing unit and an outside covering for tightening the ball-end set screw, situated on the
extra protection against dust. Special consideration Table 3.1 Recommended torques for tightening set screws
inner ring. This is a unique feature which prevents
has been given to its design with respect to dust- loosening, even if the bearing is subject to intense
A) Metric series, applied to metric bore size. B) Inch series, applied to inch bore size.
proofing. vibrations and shocks.
Sealing devices are provided in both the bearing Designation Tightening Designation of the bearings Designation Tightening
Designation of the bearings
and the housing, so that units of this type operate of torques for the unit to which of torques
2.5 SELF-ALIGNING of applicable units
set screws N m (max.) torques given are applicable set screws lbfinch (max.)
satisfactorily even in such adverse environments
as flour mills, steel mills, foundries, galvanizing With the NSK bearing unit, the outer surface of UC201 to UC201 to
plants and chemical plants, where excessive dust the ball bearing and the inner surface of the housing M 50.8 7 3.9 No.10 -32UNF 34
UC205 UC205
is produced and/or liquids are used. They are also are spherical, thus this bearing unit has self-aligning
eminently suitable for outdoor environments where characteristic. Any misalignment of axis that arise UC206
UC305 to
M 60.75 8 4.9 UC206
UC305 to
1/4 -28UNF 43
dust and rain are inevitable, and in heavy industrial from poor workmanship on the shaft or errors in UC306 UC306
machinery such as construction and transportation fitting will be properly adjusted.
equipment. UC207 UCX05 M 60.75 8 5.8 UC207 UCX05 1/4 -28UNF 52
The rubber seal of the cover contacts with the shaft 2.6 HIGHER RATED LOAD CAPACITY
by its two lips, as shown in Fig. 2.2 and 2.3. By The bearing used in the unit is of the same internal UC208 to UC208 to
filling the groove between the two lips with grease, M 81 10 7.8 5/16 -24UNF 69
construction as those in bearing series 62 and 63, UC210 UC210
an excellent sealing effect is obtained and, at the and is capable of accommodating axial load as well
same time, the contacting portions of the lips are UCX06 to UCX06 to
as radial load, or composite load. The rated load UC211 UC307 M 81 10 9.8 UC211 UC307 5/16 -24UNF 86
lubricated. Furthermore, the groove is so designed capacity or this bearing is considerably higher than UCX08 UCX08
that when the shaft is inclined the rubber seal can that of the corresponding self-aligning ball bearings
move in the radial direction. used for standard plummer blocks UC212 UCX09 M101.2512 16.6 UC212 UCX09 3/8 -24UNF 147
When bearing units are exposed to splashes of
water rather than to dust, a drain hole (5 to 8 mm, 2.7 LIGHT WEIGHT YET STRONG HOUSING UC213 to UC308 to UC213 to UC308 to
3/8
0.2 to 0.3 inches in diameter)is provided at the M101.2512 19.6 -24UNF 173
Housings for NSK bearing units come in various UC215 UC309 UC215 UC309
bottom of the cover, and grease should be applied
to the side of the bearing itself instead of into the shapes. They consist of either high-grade cast iron,
3/8
cover. one-piece casting, or of precision finished pressed UC216 UCX10 M101.2512 22.5 UC216 UCX10 -24UNF 199
steel, the latter being lighter in weight. In either
case, they are practically designed to combine
UCX11 to
M101.2512 24.5
UCX11 to
3/8 -24UNF 216
lightness with maximum strength. UCX12 UCX12
2.8 EASY MOUNTING UC217 to UCX13 to UC310 to

M121.5 13 29.4
UC217 to UCX13 to UC310 to
1/2 -20UNF 260
UC218 UCX15 UC314 UC218 UCX15 UC314
The NSK bearing unit is an integrated unit
consisting of a bearing and a housing.
UCX16 to
M121.5 13 34.3
UCX16 to
1/2 -20UNF 303
As the bearing is prelubricated at manufacture with UCX17 UCX17
the correct amount of high-grade lithium base, it can
UC315 to UC315 to
be mounted on the shaft just as it is. It is sufficient UCX18 M141.5 15 34.3 UCX18 9/16 -18UNF 303
to carry out a short test run after mounting. UC316 UC316
UC317 to UC317 to
2.9 ACCURATE FITTING OF THE HOUSING UCX20
UC319
M161.5 18 53.9 UCX20
UC318
5/8 -18UNF 477
In order to simplify the fitting of the pillow block

UC320 to
Fig. 2.2 Pressed steel cover and flange type bearing units, the housings are M181.5 20 58.8 UC320 5/8 -18UNF 520
provided with a seat for a dowel pin, which may be UC324
utilized as needed. UC326 to
M201.5 25 78.4
UC328
2.10 BEARING REPLACEABILITY
The bearing used in the NSK bearing unit is
replaceable. In the event of bearing failure, a new
bearing can be fitted to the existing housing. Designation Tightening Designation of the bearings Designation Tightening
Designation of the bearings
of torques for the unit to which of torques
of applicable units
set screws N m (max.) torques given are applicable set screws lbfinch (max.)
AS201 to 205 M50.8 7 3.4 AS201 to 205 No 10-32UNF 30
AS206 M60.75 8 4.4 AS206 1/4 -28UNF 39
AS207 M60.75 8 4.9 AS207 1/4 -28UNF 43
Fig.2.3 Cast iron cover AS208 M81 10 6.8 AS208 5/16-24UNF 60
B 284 B 285
B280-303E.indd 284-285 11/20/13 5:00:43 PM

UCP2
Pillow blocks units cast housing
Set screw type
B B B
S S 30 S
N H2 N H2 t N H3
N1 N1 N1 t
H H H
H1 H1 H1
L1 A L1 A L1 A
J J A4 J A5
L L L
Pressed steel dust cover type Cast dust cover type
Open end Z-UCPD1 Open end C-UCPD1
Closed end ZM-UCPD1 Closed end CM-UCPD1
Shaft Unit number(1) Nominal dimensions Bolt Bearing Housing Unit number (1) Unit number (1) Nominal dimensions Mass of unit
dia. size number number pressed steel dust cast dust cover type
cover type
mm inch mm inch kg lb
mm mm t A4 H3 A5
inch H L J A N N1 H1 H2 L1 B S inch max. UCP Z(ZM) C(CM)
12 UCP201D1 30.2 127 95 38 13 16 14 62 42 31 12.7 M10 UC201D1 P203D1 Z(ZM)-UCP201D1 C(CM)-UCP201D1 2 45 67 62 0.7 0.7 1.0
1/2 UCP201-008D1 1 3 / 16 5 33/4 11/2 1/2 5/8 9 / 16 2 7/ 16 1 21/ 32 1.2205 0.500 3/8 UC201-008D1 P203D1 Z(ZM)-UCP201-008D1 C(CM)-UCP201-008D1 5 / 64 1 25/ 32 25/8 2 7/ 16 1.5 1.5 2.2
9 / 16 UCP202-009D1 UC202-009D1 P203D1 Z(ZM)-UCP202-009D1 C(CM)-UCP202-009D1
5 / 8 UCP202-010D1
1 3/ 16 5 33/4 11/2 1/2 5/8 9 / 16 2 7/ 16 1 21/ 32 1.2205 0.500 3/8 5 / 64 1 25/ 32 25/8 2 7/ 16 1.5 1.5 2.2
UC202-010D1 P203D1 Z(ZM)-UCP202-010D1 C(CM)-UCP202-010D1
11 / 16 UCP203-011D1 1 3 / 16 5 33/4 11/2 1/2 5/8 9 / 16 2 7/ 16 1 21/ 32 1.2205 0.500 3/8 UC203-011D1 P203D1 Z(ZM)-UCP203-011D1 C(CM)-UCP203-011D1 5 / 64 1 25/ 32 25/8 2 7/ 16 1.5 1.5 2.2
3/4 UCP204-012D1 1 5 / 16 5 33/4 11/2 1/2 5/8 9 / 16 2 9/ 16 1 21/ 32 1.2205 0.500 3/8 UC204-012D1 P204D1 Z(ZM)-UCP204-012D1 C(CM)-UCP204-012D1 5 / 64 1 25/ 32 23/4 2 7/ 16 1.5 1.5 2.0
25 UCP205D1 36.5 140 105 38 13 16 15 71 42 34.1 14.3 M10 UC205D1 P205D1 Z(ZM)-UCP205D1 C(CM)-UCP205D1 2 48 76 70 0.8 0.9 1.1
7/8 UCP205-014D1 UC205-014D1 P205D1 Z(ZM)-UCP205-014D1 C(CM)-UCP205-014D1
1 7/ 16 51/2 41/8 11/2 1/2 5/8 19 / 32 2 25/ 32 1 21/ 32 1.3425 0.563 3/8 5 / 64 1 29/ 32 3 23/4 1.8 2.0 2.4
1 UCP205-100D1 UC205-100D1 P205D1 Z(ZM)-UCP205-100D1 C(CM)-UCP205-100D1
1 1/ 16 UCP206-101D1 UC206-101D1 P206D1 Z(ZM)-UCP206-101D1 C(CM)-UCP206-101D1
11/8 UCP206-102D1 11 UC206-102D1 P206D1 Z(ZM)-UCP206-102D1 C(CM)-UCP206-102D1 5 / 64 2 3/ 32 3 15/ 32 2 15/ 16 3.1 3.1 3.7
1 / 16 61/2 43/4 17/8 21 / 32 25 / 32 21 / 32 3 9/ 32 21/8 1.5000 0.626 1/2
11/4 UCP206-104D1 UC206-104D1 P206D1
1 5/ 16 UCP207-105D1 UC207-105D1 P207D1 Z(ZM)-UCP207-105D1 C(CM)-UCP207-105D1 1/8 23/8 3 29/ 32 3 5/ 32 3.5 3.7 4.4
17/8 6 9/ 16 5 17/8 21 / 32 25 / 32 23 / 32 3 21/ 32 2 1/ 8 1.6890 0.689 1/2
1 7/ 16 UCP207-107D1 UC207-107D1 P207D1
40 UCP208D1 49.2 184 137 54 17 20 18 98 52 49.2 19 M14 UC208D1 P208D1 Z(ZM)-UCP208D1 C(CM)-UCP208D1 3 69 105 90 1.9 2.1 2.7
1 1/ 2 UCP208-108D1 15 UC208-108D1 P208D1 Z(ZM)-UCP208-108D1 C(CM)-UCP208-108D1
1 / 16 71/4 5 13/ 32 2 1/ 8 21 / 32 25 / 32 23 / 32 3 27/ 32 2 1/ 16 1.9370 0.748 1/2 1/8 2 23/ 32 41/8 3 17/ 32 4.2 4.6 6.0
Note (1) These numbers indicate relubricatable type. If maintenance free type is needed, please order without suffix D1.
B 286 B 287
B280-303E.indd 286-287 11/20/13 5:00:44 PM

UCP2
Set screw type
B B B
S S 30 S
N H2 N H2 t N H3
N1 N1 N1 t
H H H
H1 H1 H1
L1 A L1 A L1 A
J J A4 J A5
L L L
cover type
mm mm t A4 H3 A5
45 UCP209D1 54 190 146 54 17 20 20 106 60 49.2 19 M14 UC209D1 P209D1 Z(ZM)-UCP209D1 C(CM)-UCP209D1 3 69 113 95 2.2 2.4 3.1
1 11/ 16 UCP209-111D1 2 1 / 8 7 15/ 32 53/4 21/8 21 / 32 25 / 32 25 / 32 4 3/ 16 23/8 1.9370 0.748 1/2 UC209-111D1 P209D1 Z(ZM)-UCP209-111D1 C(CM)-UCP209-111D1 1/8 2 23/ 32 4 7/ 16 33/4 4.9 5.3 6.8
50 UCP210D1 57.2 206 159 60 20 23 21 114 65 51.6 19 M16 UC210D1 P210D1 Z(ZM)-UCP210D1 C(CM)-UCP210D1 3 76 119 100 2.7 2.8 3.6
17/8 UCP210-114D1
21/4 81/8 61/4 23/8 25 / 32 29 / 32 13 / 16 41/2 2 9/ 16 2.0315 0.748 5/8 UC210-114D1 P210D1 Z(ZM)-UCP210-114D1 C(CM)-UCP210-114D1 1/8 3 4 11/ 16 3 15/ 16 6.0 6.2 7.9
2 UCP210-200D1 UC210-200D1 P210D1 C(CM)-UCP210-200D1
2 UCP211-200D1 UC211-200D1 P211D1 Z(ZM)-UCP211-200D1 C(CM)-UCP211-200D1
2 1/ 16 UCP211-201D1
21/2 85/8 6 23/ 32 2 3/ 8 25 / 32 29 / 32 29 / 32 4 31/ 32 2 9/ 16 2.1890 0.874 5/8 UC211-201D1 P211D1 Z(ZM)-UCP211-201D1 C(CM)-UCP211-201D1 5 / 32 3 1/ 32 51/8 3 15/ 16 7.7 7.7 9.7
23/4 91/2 71/4 23/4 25 / 32 29 / 32 31 / 32 5 7/ 16 23/4 2.5630 1.000 5/8 5 / 32 31/2 55/8 4 17/ 32 10 11 13
2 7/ 16 UCP212-207D1 UC212-207D1 P212D1 C(CM)-UCP212-207D1
3 10 7/ 16 8 23/4 31 / 32 1 3/ 32 1 1/ 16 5 15/ 16 3 1/ 32 2.5630 1.000 3/4 5 / 32 3 19/ 32 6 3/ 32 4 23/ 32 12 13 16
70 UCP214D1 79.4 266 210 72 25 28 27 157 77 74.6 30.2 M20 UC214D1 P214D1 C(CM)-UCP214D1 4 162 135 6.5 8.3
25/8 UCP214-210D1 UC214-210D1 P214D1 C(CM)-UCP214-210D1
2 11/ 16 UCP214-211D1 3 1 / 8 10 15/ 32 8 9/ 32 2 27/ 32 31/ 32 1 3/ 32 1 1/ 16 6 3/ 16 3 1/ 32 2.9370 1.189 3/4 UC214-211D1 P214D1 C(CM)-UCP214-211D1 5 / 32 63/8 5 5/ 16 14 18
B 288 B 289
B280-303E.indd 288-289 11/20/13 5:00:46 PM

UCP2
Set screw type
B B B
S S 30 S
N H2 N H2 t N H3
N1 N1 N1 t
H H H
H1 H1 H1
L1 A L1 A L1 A
J J A4 J A5
L L L
cover type
mm mm t A4 H3 A5
75 UCP215D1 82.6 275 217 74 25 28 28 163 80 77.8 33.3 M20 UC215D1 P215D1 C(CM)-UCP215D1 4 168 135 7.2 9.3
27/8 UCP215-214D1
31/4 10 13/ 16 8 17/ 32 2 29/ 32 31/ 32 1 3/ 32 1 3/ 32 6 13/ 32 3 5/ 32 3.0630 1.311 3/4 UC215-214D1 P215D1 C(CM)-UCP215-214D1 5 / 32 65/8 5 5/ 16 16 21
3 UCP215-300D1 UC215-300D1 P215D1 C(CM)-UCP215-300D1
80 UCP216D1 88.9 292 232 78 25 28 30 175 85 82.6 33.3 M20 UC216D1 P216D1 C(CM)-UCP216D1 4 181 145 8.7 11
31/8 UCP216-302D1 3 1 / 2 11 1/ 2 91/8 3 1/ 16 31/ 32 1 3/ 32 1 3/ 16 67/8 3 11/ 32 3.2520 1.311 3/4 UC216-302D1 P216D1 C(CM)-UCP216-302D1 5 / 32 71/8 5 23/ 32 19 24
85 UCP217D1 95.2 310 247 83 25 28 32 187 85 85.7 34.1 M20 UC217D1 P217D1 C(CM)-UCP217D1 5 191 155 11 13
3 5/ 16 UCP217-305D1 3 3 / 4 12 7/ 32 9 23/ 32 3 9/ 32 31/ 32 1 3/ 32 1 1/ 4 7 3/ 8 3 11/ 32 3.3740 1.343 3/4 UC217-305D1 P217D1 C(CM)-UCP217-305D1 13 / 64 7 17/ 32 6 3/ 32 24 29
90 UCP218D1 101.6 327 262 88 27 30 33 200 90 96 39.7 M22 UC218D1 P218D1 C(CM)-UCP218D1 5 204 165 13 16
31/2 UCP218-308D1 4 12 7/ 8 10 5/ 16 3 15/ 32 1 1/ 16 1 3/ 16 1 5/ 16 7 7/ 8 3 17/ 32 3.7795 1.563 7/8 UC218-308D1 P218D1 C(CM)-UCP218-308D1 13 / 64 8 1/ 32 61/2 29 35
B 290 B 291
B280-303E.indd 290-291 11/20/13 5:00:47 PM

UCF2
Square flanged units cast housing
Set screw type
N B N B N B
S S S
JL JL JL
t t
J A1 J A1 A1
A2 J
L A2 L A A2
A4 L A5
A
A0 Pressed steel dust cover type Cast dust cover type
Open end Z-UCFD1 Open end C-UCFD1
Closed end ZM-UCFD1 Closed end CM-UCFD1
cover type
mm mm t A4 A5
inch L J A2 A1 A N A0 B S inch max. UCP Z(ZM) C(CM)
12 UCF201D1 86 64 15 11 25.5 12 33.3 31 12.7 M10 UC201D1 F204D1 Z(ZM)-UCF201D1 C(CM)-UCF201D1 2 38 46 0.6 0.6 0.8
1/2 UCF201-008D1 33/8 2 33/ 64 19 / 32 7 / 16 1 15 / 32 1 5/ 16 1.2205 0.500 3/8 UC201-008D1 F204D1 Z(ZM)-UCF201-008D1 C(CM)-UCF201-008D1 5 / 64 11/2 1 13/ 16 1.3 1.3 1.8
9 / 16 UCF202-009D1 UC202-009D1 F204D1 Z(ZM)-UCF202-009D1 C(CM)-UCF202-009D1
5/8
33/8 2 33/ 64 19 / 32 7 / 16 1 15 / 32 1 5/ 16 1.2205 0.500 3/8 5 / 64 11/2 1 13/ 16 1.3 1.3 1.8
UCF202-010D1 UC202-010D1 F204D1 Z(ZM)-UCF202-010D1 C(CM)-UCF202-010D1
11 / 16 UCF203-011D1 33/8 2 33/ 64 19 / 32 7 / 16 1 15 / 32 1 5/ 16 1.2205 0.500 3/8 UC203-011D1 F204D1 Z(ZM)-UCF203-011D1 C(CM)-UCF203-011D1 5 / 64 11/2 1 13/ 16 1.3 1.3 1.8
3/4 UCF204-012D1 33/8 2 33/ 64 19 / 32 7 / 16 1 15 / 32 1 5/ 16 1.2205 0.500 3/8 UC204-012D1 F204D1 Z(ZM)-UCF204-012D1 C(CM)-UCF204-012D1 5 / 64 11/2 1 13/ 16 1.3 1.3 1.5
25 UCF205D1 95 70 16 13 27 12 35.8 34.1 14.3 M10 UC205D1 F205D1 Z(ZM)-UCF205D1 C(CM)-UCF205D1 2 40 51 0.8 0.8 0.9
13 / 16 UCF205-013D1 UC205-013D1 F205D1 Z(ZM)-UCF205-013D1 C(CM)-UCF205-013D1
7/8 UCF205-014D1 UC205-014D1 F205D1 Z(ZM)-UCF205-014D1 C(CM)-UCF205-014D1
15 / 16
33/4 23/4 5/8 1/2 1 1/ 16 15 / 32 1 13/ 32 1.3425 0.563 3/8 5 / 64 1 19/ 32 2 1.8 1.8 2.0
UCF205-015D1 UC205-015D1 F205D1 Z(ZM)-UCF205-015D1 C(CM)-UCF205-015D1
1 UCF205-100D1 UC205-100D1 F205D1 Z(ZM)-UCF205-100D1 C(CM)-UCF205-100D1
1 1/ 16 UCF206-101D1 UC206-101D1 F206D1 Z(ZM)-UCF206-101D1 C(CM)-UCF206-101D1
11/8 UCF206-102D1
41/4 3 17/ 64 45 / 64 1/2 1 7/ 32 15 / 32 1 37/ 64 1.5000 0.626 3/8 UC206-102D1 F206D1 Z(ZM)-UCF206-102D1 C(CM)-UCF206-102D1 5 / 64 13/4 2 7/ 32 2.4 2.4 2.9
11/4 UCF206-104D1 UC206-104D1 F206D1 C(CM)-UCF206-104D1
4 19/ 32 35/8 3/4 19 / 32 1 11/ 32 35 / 64 13/4 1.6890 0.689 7 / 16 1/8 1 15/ 16 2 5/ 16 3.3 3.3 4.0
1 7/ 16 UCF207-107D1 UC207-107D1 F207D1 C(CM)-UCF207-107D1
40 UCF208D1 130 102 21 15 36 16 51.2 49.2 19 M14 UC208D1 F208D1 Z(ZM)-UCF208D1 C(CM)-UCF208D1 3 56 66 1.7 1.8 2.2
51/8 4 1/ 64 53 / 64 19 / 32 1 13/ 32 5/8 2 1/ 64 1.9370 0.748 1/2 1/8 2 3/ 16 2 19/ 32 3.7 4.0 4.9
B 292 B 293
B280-303E.indd 292-293 11/20/13 5:00:48 PM

UCF2
Set screw type
N B N B N B
S S S
JL JL JL
t t
J A1 J A1 A1
A2 J
L A2 L A A2
A4 L A5
A
cover type
mm mm t A4 A5
inch L J A2 A1 A N A0 B S inch max. UCF Z(ZM) C(CM)
1 11/ 16 UCF209-111D1 5 13/ 32 4 9/ 64 55 / 64 5/8 11/2 5/8 2 1/ 16 1.9370 0.748 1/2 UC209-111D1 F209D1 Z(ZM)-UCF209-111D1 C(CM)-UCF209-111D1 1/8 21/4 23/4 4.6 4.9 5.7
17/8 UCF210-114D1
55/8 43/8 55 / 64 5/8 1 9/ 16 5/8 2 5/ 32 2.0315 0.748 1/2 UC210-114D1 F210D1 Z(ZM)-UCF210-114D1 C(CM)-UCF210-114D1 1/8 23/8 2 27/ 32 5.5 5.5 6.6
2 UCF210-200D1 UC210-200D1 F210D1 C(CM)-UCF210-200D1
2 UCF211-200D1 UC211-200D1 F211D1 Z(ZM)-UCF211-200D1 C(CM)-UCF211-200D1
2 1/ 16 UCF211-201D1
63/8 51/8 63 / 64 23 / 32 1 11/ 16 3/4 2 19/ 64 2.1890 0.874 5/8 UC211-201D1 F211D1 Z(ZM)-UCF211-201D1 C(CM)-UCF211-201D1 5 / 32 21/2 2 15/ 16 7.3 7.5 8.8
2 5/ 16 UCF212-205D1
67/8 55/8 1 9/ 64 23 / 32 17/8 3/4 2 45/ 64 2.5630 1.000 5/8 UC212-205D1 F212D1 Z(ZM)-UCF212-205D1 C(CM)-UCF212-205D1 5 / 32 2 29/ 32 33/8 8.6 9.0 11
2 1/ 2 UCF213-208D1 73/8 5 55/ 64 1 3/ 16 7/8 1 31/ 32 3/4 23/4 2.5630 1.000 5/8 UC213-208D1 F213D1 Z(ZM)-UCF213-208D1 C(CM)-UCF213-208D1 5 / 32 3 3 17/ 32 12 12 14
70 UCF214D1 193 152 31 22 54 19 75.4 74.6 30.2 M16 UC214D1 F214D1 C(CM)-UCF214D1 4 98 6.3 7.4
2 11/ 16 UCF214-211D1 7 19/ 32 5 63/ 64 1 7/ 32 7/8 21/8 3/4 2 31/ 32 2.9370 1.189 5/8 UC214-211D1 F214D1 C(CM)-UCF214-211D1 5 / 32 3 27/ 32 14 16
B 294 B 295
B280-303E.indd 294-295 11/20/13 5:00:50 PM

UCF2
Set screw type
N B N B N B
S S S
JL JL JL
t t
J A1 J A1 A1
A2 J
L A2 L A A2
A4 L A5
A
cover type
mm mm t A4 A5
inch L J A2 A1 A N A0 B S inch max. UCF Z(ZM) C(CM)
77/8 6 17/ 64 1 11/ 32 7/8 2 7/ 32 3/4 3 3/ 32 3.0630 1.311 5/8 5 / 32 4 1/ 32 15 17
3 UCF215-300D1 UC215-300D1 F215D1 C(CM)-UCF215-300D1
1
3 /8 UCF216-302D1 8 3/ 16 61/2 1 11/ 32 7/8 2 9/ 32 29 / 32 3 9/ 32 3.2520 1.311 3/4 UC216-302D1 F216D1 C(CM)-UCF216-302D1 5 / 32 4 3/ 16 17 21
85 UCF217D1 220 175 36 24 63 23 87.6 85.7 34.1 M20 UC217D1 F217D1 C(CM)-UCF217D1 5 114 9.8 12
3 5/ 16 UCF217-305D1 8 21/ 32 6 57/ 64 1 27/ 64 15 / 16 2 15/ 32 29 / 32 3 29/ 64 3.3740 1.343 3/4 UC217-305D1 F217D1 C(CM)-UCF217-305D1 13 / 64 41/2 22 26
90 UCF218D1 235 187 40 24 68 23 96.3 96 39.7 M20 UC218D1 F218D1 C(CM)-UCF218D1 5 122 12 13
31/2 UCF218-308D1 91/4 7 23/ 64 1 37/ 64 15 / 16 2 11/ 16 29 / 32 3 51/ 64 3.7795 1.563 3/4 UC218-308D1 F218D1 C(CM)-UCF218-308D1 13 / 64 4 13/ 16 26 29
B 296 B 297
B280-303E.indd 296-297 11/20/13 5:00:51 PM

UCFL2
Rhombus flanged units cast housing
Set screw type
B
B B S
45 S 45 S 45
N N N
L L L1
t t
L2
A1 A1 J A1
J J
H A2 H A2 H A2
A A A5
A4
Open end Z-UCFLD1 Open end C-UCFLD1
Closed end ZM-UCFLD1 Closed end CM-UCFLD1
cover type
mm mm t A4 A5 L1 L2
inch H J A2 A1 A N L A0 B S inch max. UCFL Z(ZM) C(CM)
12 UCFL201D1 113 90 15 11 25.5 12 60 33.3 31 12.7 M10 UC201D1 FL204D1 Z(ZM)-UCFL201D1 C(CM)-UCFL201D1 2 38 46 67 30 0.5 0.5 0.6
1/2 UCFL201-008D1 4 7/ 16 3 35/ 64 19/ 32 7 / 16 1 15 / 32 23/8 1 5/ 16 1.2205 0.500 3/ 8 UC201-008D1 FL204D1 Z(ZM)-UCFL201-008D1 C(CM)-UCFL201-008D1 5 / 64 11/2 1 13/ 16 25/8 1 3/ 16 1.1 1.1 1.3
9 / 16 UCFL202-009D1 UC202-009D1 FL204D1 Z(ZM)-UCFL202-009D1 C(CM)-UCFL202-009D1
5/8
4 7/ 16 3 35/ 64 19/ 32 7 / 16 1 15 / 32 23/8 1 5/ 16 1.2205 0.500 3/8 5 / 64 11/2 1 13/ 16 25/8 1 3/ 16 1.1 1.1 1.3
UCFL202-010D1 UC202-010D1 FL204D1 Z(ZM)-UCFL202-010D1 C(CM)-UCFL202-010D1
11 / 16 UCFL203-011D1 4 7/ 16 3 35/ 64 19/ 32 7 / 16 1 15 / 32 23/8 1 5/ 16 1.2205 0.500 3/ 8 UC203-011D1 FL204D1 Z(ZM)-UCFL203-011D1 C(CM)-UCFL203-011D1 5 / 64 11/2 1 13/ 16 25/8 1 3/ 16 1.1 1.1 1.3
3/4 UCFL204-012D1 4 7/ 16 3 35/ 64 19/ 32 7 / 16 1 15 / 32 23/8 1 5/ 16 1.2205 0.500 3/ 8 UC204-012D1 FL204D1 Z(ZM)-UCFL204-012D1 C(CM)-UCFL204-012D1 5 / 64 11/2 1 13/ 16 25/8 1 3/ 16 0.9 0.9 1.3
25 UCFL205D1 130 99 16 13 27 16 68 35.8 34.1 14.3 M14 UC205D1 FL205D1 Z(ZM)-UCFL205D1 C(CM)-UCFL205D1 2 40 51 74 34 0.6 0.6 0.8
13 / 16 UCFL205-013D1 UC205-013D1 FL205D1 Z(ZM)-UCFL205-013D1 C(CM)-UCFL205-013D1
7/8 UCFL205-014D1 UC205-014D1 FL205D1 Z(ZM)-UCFL205-014D1 C(CM)-UCFL205-014D1
15 / 16
51/8 3 57/ 64 5/8 1/2 1 1/ 16 5/8 2 11/ 16 1 13/ 32 1.3425 0.563 1/2 5 / 64 1 19/ 32 2 2 29/ 32 1 11/ 32 1.3 1.3 1.8
UCFL205-015D1 UC205-015D1 FL205D1 Z(ZM)-UCFL205-015D1 C(CM)-UCFL205-015D1
1 UCFL205-100D1 UC205-100D1 FL205D1 Z(ZM)-UCFL205-100D1 C(CM)-UCFL205-100D1
1 1/ 16 UCFL206-101D1 UC206-101D1 FL206D1 Z(ZM)-UCFL206-101D1 C(CM)-UCFL206-101D1
5 13/ 16 4 39/ 64 45/ 64 1/2 1 7/ 32 5/8 3 5/ 32 1 37/ 64 1.5000 0.626 1/2 5 / 64 13/4 2 7/ 32 3 11/ 32 1 9/ 16 2.0 2.0 2.6
11/4 UCFL206-104D1 UC206-104D1 FL206D1
6 11/ 32 51/8 3/4 19 / 32 1 11/ 32 5/8 3 17/ 32 1 3/ 4 1.6890 0.689 1/2 1/8 1 15/ 16 2 5/ 16 3 13/ 16 1 25/ 32 2.6 2.6 3.1
1 7/ 16 UCFL207-107D1 UC207-107D1 FL207D1
40 UCFL208D1 175 144 21 15 36 16 100 51.2 49.2 19 M14 UC208D1 FL208D1 Z(ZM)-UCFL208D1 C(CM)-UCFL208D1 3 56 66 106 50 1.5 1.5 1.9
67/8 5 43/ 64 53/ 64 19/ 32 1 13/ 32 5/8 3 15/ 16 2 1/ 64 1.9370 0.748 1/2 1/8 2 3/ 16 2 19/ 32 4 3/ 16 1 31/ 32 3.3 3.3 4.2
B 298 B 299
B280-303E.indd 298-299 11/20/13 5:00:52 PM

UCFL2
Set screw type
B
B B S
45 S 45 S 45
N N N
L L L1
t t
L2
A1 A1 J A1
J J
H A2 H A2 H A2
A A A5
A4
cover type
mm mm t A4 A5 L1 L2
1 11/ 16 UCFL209-111D1 7 13/ 32 5 53/ 64 55/ 64 5/8 11/2 3/4 41/4 2 1/ 16 1.9370 0.748 5/8 UC209-111D1 FL209D1 Z(ZM)-UCFL209-111D1 C(CM)-UCFL209-111D1 1/8 21/4 23/4 4 7/ 16 21/8 4.0 4.2 5.1
73/4 6 3/ 16 55/ 64 5/8 1 9/ 16 3/4 4 17/ 32 2 5/ 32 2.0315 0.748 5/8 1/8 23/8 2 27/ 32 4 23/ 32 2 9/ 32 4.4 4.6 6.0
2 UCFL210-200D1 UC210-200D1 FL210D1 C(CM)-UCFL210-200D1
2 UCFL211-200D1 UC211-200D1 FL211D1 Z(ZM)-UCFL211-200D1 C(CM)-UCFL211-200D1
8 13/ 16 7 1/ 4 63/ 64 23/ 32 1 11/ 16 3/ 4 5 1/ 8 2 19/ 64 2.1890 0.874 5/8 5 / 32 21/2 2 15/ 16 51/4 2 9/ 16 6.4 6.6 7.5
9 27/ 32 7 61/ 64 1 9/ 64 23/ 32 1 7/ 8 29/ 32 5 1/ 2 2 45/ 64 2.5630 1.000 3/4 5 / 32 2 29/ 32 33/8 5 21/ 32 2 3/ 4 8.4 8.9 10
2 7/ 16 UCFL212-207D1 UC212-207D1 FL212D1 C(CM)-UCFL212-207D1
21/2 UCFL213-208D1
10 5/ 32 8 17/ 64 1 3/ 16 7/8 1 31/ 32 29/ 32 6 3/ 32 2 3/ 4 2.5630 1.000 3/4 UC213-208D1 FL213D1 Z(ZM)-UCFL213-208D1 C(CM)-UCFL213-208D1 5 / 32 3 3 17/ 32 6 3/ 16 3 1/ 16 11 11 15
70 UCFL214D1 265 216 31 22 54 23 160 75.4 74.6 30.2 M20 UC214D1 FL214D1 C(CM)-UCFL214D1 4 98 164 80 5.4 7.7
25/8 UCFL214-210D1 UC214-210D1 FL214D1 C(CM)-UCFL214-210D1
2 11/ 16 UCFL214-211D1 10 7/ 16 8 1/ 2 1 7/ 32 7/8 2 1/ 8 29/ 32 6 5/ 16 2 31/ 32 2.9370 1.189 3/4 UC214-211D1 FL214D1 C(CM)-UCFL214-211D1 5 / 32 3 27/ 32 6 15/ 32 3 5/ 32 12 17
B 300 B 301
B280-303E.indd 300-301 11/20/13 5:00:53 PM

UCFL2
Set screw type
B
B B S
45 S 45 S 45
N N N
L L L1
t t
L2
A1 A1 J A1
J J
H A2 H A2 H A2
A A A5
A4
cover type
mm mm t A4 A5 L1 L2
27/8 UCFL215-214D1 UC215-214D1 FL215D1
C(CM)-UCFL215-214D1 5 / 32 4 1/ 32 6 21/ 32 3 7/ 32 13 16
10 13/ 16 8 55/ 64 1 11/ 32 7/8 2 7/ 32 29/ 32 61/2 3 3/ 32 3.0630 1.311 3/4
3 UCFL215-300D1 UC215-300D1 FL215D1 C(CM)-UCFL215-300D1
31/8 UCFL216-302D1 11 13/ 32 9 11/ 64 1 11/ 32 7/8 2 9/ 32 63/ 64 7 3/ 32 3 9/ 32 3.2520 1.311 7/8 UC216-302D1 FL216D1 C(CM)-UCFL216-302D1 5 / 32 4 3/ 16 7 7/ 32 3 17/ 32 16 19
85 UCFL217D1 305 248 36 24 63 25 190 87.6 85.7 34.1 M22 UC217D1 FL217D1 C(CM)-UCFL217D1 5 114 192 95 8.8 10
3 5/ 16 UCFL217-305D1 12 9 49/ 64 1 27/ 64 15/ 16 2 15/ 32 63/ 64 7 15/ 32 3 29/ 64 3.3740 1.343 7/8 UC217-305D1 FL217D1 C(CM)-UCFL217-305D1 13 / 64 41/2 7 9/ 16 33/4 19 22
90 UCFL218D1 320 265 40 24 68 25 205 96.3 96 39.7 M22 UC218D1 FL218D1 C(CM)-UCFL218D1 5 122 205 102 11 13
31/2 UCFL218-308D1 12 19/ 32 10 7/ 16 1 37/ 64 15/ 16 2 11/ 16 63/ 64 8 1/ 16 3 51/ 64 3.7795 1.563 7/ 8 UC218-308D1 FL218D1 C(CM)-UCFL218-308D1 13 / 64 4 13/ 16 8 1/ 16 4 1/ 32 24 29
B 302 B 303
B280-303E.indd 302-303 11/20/13 5:00:55 PM

PLUMMER BLOCKS
STANDARD TYPE PLUMMER BLOCKS B306
LARGE PLUMMER BLOCKS B312
DUSTPROOF PLUMMER BLOCKS B316
STEPPED-SHAFT TYPE PLUMMER
BLOCKS B318
DESIGN, TYPES AND FEATURES
There are numerous types and sizes of plummer blocks. In this catalog, only the types
marked by are shown.
SN 5 SN 5B
SN 6 SN 6B
SN 30 SN 30B
SN 31 These are the most common type. SN 31B These have the same dimensions as
SN 2 Models SN30 and SN31 are for medium SN 2B those of types SN5 and SN6. To increase
SN 3 loads. SN 3B the bearing box strength, no material is
SN 2C For types SN2C and SN3C, the bore SN 2BC removed from the top or bottom of the base,
SN 3C diameters on the two sides are different. SN 3BC so mounting holes can be drilled anywhere.
SG 5 SD 30S
SD 31S
SD 5
Dustproof plummer blocks have a SD 6 These are large and made for heavy loads.
combination of oil seals, labyrinth seals, and SD 2 The standard ones have double seals and
oil groove seals, therefore, they are suitable SD 3 four mounting bolt holes. For types SD2C
for environments with much dust and other SD 2C and SD3C, the bore diameters on the two
foreign matter. SD 3C sides are different.
SD31TS Single-piece plummer blocks

SD32TS VC (integrated type roller bearing unit)have
higher rigidity and precision than split type
These are provided with labyrinth seals, so plummer blocks.
they are suitable for high speed applications.
B 304 B 305
B304-325E.indd 304-305 11/20/13 5:01:16 PM

STANDARD TYPE PLUMMER BLOCKS
SN 5, SN 6 Types
Shaft Diameter 20 55 mm
A
t g Width
N1
Free-End
Outside Diameter
N A1 H2 jD jd 1
s
H
Fixed-End
J H1
L Locating Ring
X( 2)
Shaft Plummer Dimensions Mass Applicable Parts Oil

Diameter (mm) (kg) Seals (3)
(mm)
Block Self-Aligning Ball Bearing Spherical Roller Bearing Adapter Locating Rings
d 1 Bearing Box1 D H J N N1 A L A1 H1 H2 g t s Numbers Basic Dynamic Load Numbers Basic Dynamic Load Numbers
Outside
Nominal ( Dia. Width ) Q'ty
Numbers ( ) H8 h13 H13 nominal nominal approx. Ratings Cr (N) Ratings Cr (N)
20 SN 505 52 40 130 15 20 67 165 46 22 75 25 M 8 M 12 1.1 1205 K 12 200 H 205X SR 52 5 2 GS 5

2205 K 12 400 22205 CKE4 37 500 H 305X SR 52 7 1
SN 605 62 50 150 15 20 80 185 52 22 90 34 M 8 M 12 1.6 1305 K 18 200 21305 CDKE4 43 000 H 305X SR 62 8.5 2 GS 5
2305 K 24 900 H 2305X SR 62 10 1
25 SN 506 62 50 150 15 20 77 185 52 22 90 30 M 8 M 12 1.7 1206 K 15 800 H 206X SR 62 7 2 GS 6

2206 K 15 300 22206 CKE4 50 000 H 306X SR 62 10 1
SN 606 72 50 150 15 20 82 185 52 22 95 37 M 10 M 12 1.8 1306 K 21 400 21306 CDKE4 55 000 H 306X SR 72 9 2 GS 6
2306 K 32 000 H 2306X SR 72 10 1
30 SN 507 72 50 150 15 20 82 185 52 22 95 33 M 10 M 12 1.9 1207 K 15 900 H 207X SR 72 8 2 GS 7

2207 K 21 700 22207 CKE4 69 000 H 307X SR 72 10 1
SN 607 80 60 170 15 20 90 205 60 25 110 41 M 10 M 12 2.6 1307 K 25 300 21307 CDKE4 71 500 H 307X SR 80 10 2 GS 7
2307 K 40 000 H 2307X SR 80 10 1
35 SN 508 80 60 170 15 20 85 205 60 25 110 33 M 10 M 12 2.6 1208 K 19 300 H 208X SR 80 7.5 2 GS 8

2208 K 22 400 22208 EAKE4 90 500 H 308X SR 80 10 1
SN 608 90 60 170 15 20 95 205 60 25 115 43 M 10 M 12 2.9 1308 K 29 800 21308 EAKE4 94 500 H 308X SR 90 10 2 GS 8
2308 K 45 500 22308 EAKE4 136 000 H 2308X SR 90 10 1
40 SN 509 85 60 170 15 20 85 205 60 25 112 31 M 10 M 12 2.8 1209 K 22 000 H 209X SR 85 6 2 GS 9

2209 K 23 300 22209 EAKE4 94 500 H 309X SR 85 8 1
SN 609 100 70 210 18 23 105 255 70 28 130 46 M 12 M 16 4.1 1309 K 38 500 21309 EAKE4 119 000 H 309X SR 100 10.5 2 GS 9
2309 K 55 000 22309 EAKE4 166 000 H 2309X SR 100 10 1
45 SN 510 90 60 170 15 20 90 205 60 25 115 33 M 10 M 12 3.0 1210 K 22 800 H 210X SR 90 6.5 2 GS 10

2210 K 23 400 22210 EAKE4 99 000 H 310X SR 90 10 1
2310 K 65 000 22310 EAKE4 197 000 H 2310X SR 110 10 1
50 SN 511 100 70 210 18 23 95 255 70 28 130 33 M 12 M 16 4.5 1211 K 26 900 H 211X SR 100 6 2 GS 11
2211 K 26 700 22211 EAKE4 119 000 H 311X SR 100 8 1
2311 K 76 500 22311 EAKE4 234 000 H 2311X SR 120 10 1
55 SN 512 110 70 210 18 23 105 255 70 30 135 38 M 12 M 16 5.0 1212 K 30 500 H 212X SR 110 8 2 GS 12
2212 K 34 000 22212 EAKE4 142 000 H 312X SR 110 10 1
2312 K 88 500 22312 EAKE4 271 000 H 2312X SR 130 10 1
Note (1) Including oil seal. Notes (2) The X dimension indicates the offset of the bearing center from the center of the plummer block bearing
To place an order for a complete unit, please specify, Plummer block bearing box+bearing+adapter+locating ring. box. When one locating ring is used, it is 1/2 of the locating ring width, and when two rings are used, it
Remarks Threads for plugs are R 1/8. becomes 0.
(3) Applicable to the ZF Type with the same number.
B 306 B 307
B304-325E.indd 306-307 11/20/13 5:01:18 PM

SN 31, SN 5, SN 6 Types
A
t g Width
N1
Free-End
Outside Diameter
N A1 H2 jD jd 1
s
H
Fixed-End
J H1
L Locating Ring
X( 2)

(mm)
d 1 Bearing Box1 D H J N N1 A L A1 H1 H2 g t s Numbers Basic Dynamic Load Numbers Basic Dynamic Load Numbers
Outside
Nominal ( Dia. Width ) Q'ty
Numbers ( ) H8 h13 H13 nominal nominal approx. Ratings Cr (N) Ratings Cr (N)
60 SN 513 120 80 230 18 23 110 275 80 30 150 43 M 12 M 16 5.6 1213 K 31 000 H 213X SR 120 10 2 GS 13
2213 K 43 500 22213 EAKE4 177 000 H 313X SR 120 12 1
2313 K 97 000 22313 EAKE4 300 000 H 2313X SR 140 10 1
65 SN 515 130 80 230 18 23 115 280 80 30 155 41 M 12 M 16 7.0 1215 K 39 000 H 215X SR 130 8 2 GS 15
2215 K 44 500 22215 EAKE4 190 000 H 315X SR 130 10 1
2315 K 125 000 22315 EAKE4 390 000 H 2315X SR 160 10 1
70 SN 516 140 95 260 22 27 120 315 90 32 175 43 M 16 M 20 9.0 1216 K 40 000 H 216X SR 140 8.5 2 GS 16
2216 K 49 000 22216 EAKE4 212 000 H 316X SR 140 10 1
2316 K 130 000 22316 EAKE4 435 000 H 2316X SR 170 10 1
75 SN 517 150 95 260 22 27 125 320 90 32 185 46 M 16 M 20 10 1217 K 49 500 H 217X SR 150 9 2 GS 17
2217 K 58 500 22217 EAKE4 250 000 H 317X SR 150 10 1
SN 617 180 112 320 26 32 155 380 110 40 218 70 M 20 M 24 15 1317 K 98 500 21317 EAKE4 289 000 H 317X SR 180 14.5 2 GS 17
2317 K 142 000 22317 EAKE4 480 000 H 2317X SR 180 10 1
80 SN 518 160 100 290 22 27 145 345 100 35 195 62.4 M 16 M 20 13 1218 K 57 500 H 218X SR 160 16.2 2 GS 18
2218 K 70 500 22218 EAKE4 289 000 H 318X SR 160 11.2 2
23218 CKE4 340 000 H 2318X SR 160 10 1
SN 618 190 112 320 26 32 160 380 110 40 225 74 M 20 M 24 19 1318 K 117 000 21318 EAKE4 330 000 H 318X SR 190 15.5 2 GS 18
2318 K 154 000 22318 EAKE4 535 000 H 2318X SR 190 10 1
85 SN 519 170 112 290 22 27 140 345 100 35 210 53 M 16 M 20 15 1219 K 64 000 H 219X SR 170 10.5 2 GS 19
2219 K 84 000 22219 EAKE4 330 000 H 319X SR 170 10 1
SN 619 200 125 350 26 32 170 410 120 45 245 77 M 20 M 24 22 1319 K 129 000 21319 CKE4 345 000 H 319X SR 200 16 2 GS 19
2319 K 161 000 22319 EAKE4 590 000 H 2319X SR 200 10 1
90 SN 520 180 112 320 26 32 160 380 110 40 218 70.3 M 20 M 24 18.5 1220 K 69 500 H 220X SR 180 18.1 2 GS 20
2220 K 94 500 22220 EAKE4 365 000 H 320X SR 180 12.1 2
23220 CKE4 420 000 H 2320X SR 180 10 1
SN 620 215 140 350 26 32 175 410 120 45 270 83 M 20 M 24 25 1320 K 140 000 21320 CKE4 395 000 H 320X SR 215 18 2 GS 20
2320 K 187 000 22320 EAKE4 690 000 H 2320X SR 215 10 1
100 SN 3122 180 112 320 26 32 155 380 110 40 218 66 M 20 M 24 18 23122 CKE4 385 000 H 3122X SR 180 10 1 GS 22
SN 522 200 125 350 26 32 175 410 120 45 240 80 M 20 M 24 20 1222 K 87 000 H 222X SR 200 21 2 GS 22
2222 K 122 000 22222 EAKE4 485 000 H 322X SR 200 13.5 2
23222 CKE4 515 000 H 2322X SR 200 10 1
SN 622 240 150 390 28 36 190 450 130 50 300 90 M 24 M 24 32 1322 K 161 000 21322 CAKE4 450 000 H 322X SR 240 20 2 GS 22
2322 K 211 000 22322 EAKE4 825 000 H 2322X SR 240 10 1
Remarks 1. The threads for plugs are R 1/8 for SN 616 and SN 519 or under and R 1/4 for SN 617, SN 520, SN 3122, and over. becomes 0.
2. SN 620 and SN 622 are provided with eye bolts. (3) Applicable to the ZF Type with the same number.
B 308 B 309
B304-325E.indd 308-309 11/20/13 5:01:19 PM

SN 30, SN 31, SN 5, SN 6 Types
A
t g Width
N1
Free-End
Outside Diameter
N A1 H2 jD jd 1
s
H
Fixed-End
J H1
L Locating Ring
X( 2)

(mm)
d 1 Bearing Box1 D H J N N1 A L A1 H1 H2 g t s Numbers Basic Dynamic Load Numbers Basic Dynamic Load Numbers Nominal ( Outside Width ) Q'ty
Numbers ( ) H8 h13 H13 nominal nominal approx. Ratings Cr (N) Ratings Cr (N) Dia.
110 SN 3024 180 112 320 26 32 150 380 110 40 218 56 M 20 M 24 16 23024 CDKE4 315 000 H 3024 SR 180 10 1 GS 24
SN 3124 200 125 350 26 32 165 410 120 45 245 72 M 20 M 24 20 23124 CKE4 465 000 H 3124 SR 200 10 1 GS 24
SN 524 215 140 350 26 32 185 410 120 45 270 86 M 20 M 24 24.5 22224 EAKE4 550 000 H 3124 SR 215 14 2 GS 24
23224 CKE4 630 000 H 2324 SR 215 10 1
SN 624 260 160 450 33 42 200 530 160 60 320 96 M 24 M 30 48 22324 EAKE4 955 000 H 2324 SR 260 10 1 GS 24
115 SN 3026 200 125 350 26 32 160 410 120 45 240 62 M 20 M 24 19 23026 CDKE4 400 000 H 3026 SR 200 10 1 GS 26
SN 3126 210 140 350 26 32 170 410 120 45 270 74 M 20 M 24 26 23126 CKE4 505 000 H 3126 SR 210 10 1 GS 26
SN 526 230 150 380 28 36 190 445 130 50 290 90 M 24 M 24 30 22226 EAKE4 655 000 H 3126 SR 230 13 2 GS 26
23226 CKE4 700 000 H 2326 SR 230 10 1
SN 626 280 170 470 33 42 210 550 160 60 340 103 M 24 M 30 56 22326 CKE4 995 000 H 2326 SR 280 10 1 GS 26
125 SN 3028 210 140 350 26 32 170 410 120 45 270 63 M 20 M 24 25 23028 CDKE4 420 000 H 3028 SR 210 10 1 GS 28
SN 3128 225 150 380 28 36 180 445 130 50 290 78 M 24 M 24 32 23128 CKE4 580 000 H 3128 SR 225 10 1 GS 28
SN 528 250 150 420 33 42 205 500 150 50 305 98 M 24 M 30 38 22228 CDKE4 645 000 H 3128 SR 250 15 2 GS 28
23228 CKE4 835 000 H 2328 SR 250 10 1
SN 628 300 180 520 35 45 235 610 170 65 365 112 M 30 M 30 72 22328 CKE4 1 160 000 H 2328 SR 300 10 1 GS 28
135 SN 3030 225 150 380 28 36 175 445 130 50 290 66 M 24 M 24 29 23030 CDKE4 470 000 H 3030 SR 225 10 1 GS 30
SN 3130 250 150 420 33 42 200 500 150 50 305 90 M 24 M 30 38 23130 CKE4 725 000 H 3130 SR 250 10 1 GS 30
SN 530 270 160 450 33 42 220 530 160 60 325 106 M 24 M 30 46 22230 CDKE4 765 000 H 3130 SR 270 16.5 2 GS 30
23230 CKE4 975 000 H 2330 SR 270 10 1
SN 630 320 190 560 35 45 245 650 180 65 385 118 M 30 M 30 98 22330 CAKE4 1 220 000 H 2330 SR 320 10 1 GS 30
140 SN 3032 240 150 390 28 36 190 450 130 50 300 70 M 24 M 24 32 23032 CDKE4 540 000 H 3032 SR 240 10 1 GS 32
SN 3132 270 160 450 33 42 215 530 160 60 325 96 M 24 M 30 48 23132 CKE4 855 000 H 3132 SR 270 10 1 GS 32
SN 532 290 170 470 33 42 235 550 160 60 345 114 M 24 M 30 50 22232 CDKE4 910 000 H 3132 SR 290 17 2 GS 32
23232 CKE4 1 100 000 H 2332 SR 290 10 1
SN 632 340 200 580 42 50 255 680 190 70 405 124 M 30 M 36 115 22332 CAKE4 1 360 000 H 2332 SR 340 10 1 GS 32
Remarks 1. The threads for plugs are R 1/4. becomes 0.
2. The bearing boxes for SN 524, SN 624, SN 3126, SN 3028, and over are provided with eye bolts. (3) Applicable to the ZF Type with the same number.
B 310 B 311
B304-325E.indd 310-311 11/20/13 5:01:20 PM

LARGE-SIZE PLUMMER BLOCKS
SD 30 S, SD 31 S, SD 5, SD 6 Types
A
t g
N1
Free-End
N
J 1 A1 H2 jDjd 1
s
H
Fixed-End
J H1
L g1
Shaft Dimensions Mass Applicable Parts Oil

Diameter Plummer Block (mm) (kg) Seals (2)
(mm) Bearing Box Numbers (1) Spherical Roller Bearing Adapter
d1 Free-End Fixed-End D H J N N1 A L A1 H1 H2 J1 g g1 t s Numbers Basic Dynamic Load Numbers
H8 h13 H13 H13 nominal nominal approx. Ratings Cr (N)
150 SD 3034 S SD 3034 SG 260 160 450 36 46 230 540 200 50 315 110 77 67 M 24 M 30 70 23034 CDKE4 640 000 H 3034 GS 34
SD 3134 S SD 3134 SG 280 170 470 36 46 250 560 220 50 335 120 98 88 M 24 M 30 75 23134 CKE4 940 000 H 3134 GS 34
SD 534 SD 534 G 310 180 510 36 46 270 620 250 60 360 140 96 86 M 24 M 30 100 22234 CDKE4 990 000 H 3134 GS 34
SD 634 SD 634 G 360 210 610 36 46 300 740 290 65 420 170 130 120 M 30 M 30 160 22334 CAKE4 1 580 000 H 2334 GS 34
160 SD 3036 S SD 3036 SG 280 170 470 36 46 250 560 220 50 335 120 84 74 M 24 M 30 79 23036 CDKE4 750 000 H 3036 GS 36
SD 3136 S SD 3136 SG 300 180 520 36 46 270 630 250 55 355 140 106 96 M 24 M 30 94 23136 CKE4 1 050 000 H 3136 GS 36
SD 536 SD 536 G 320 190 540 36 46 280 650 260 60 380 150 96 86 M 24 M 30 110 22236 CDKE4 1 020 000 H 3136 GS 36
SD 636 SD 636 G 380 225 640 43 59 320 780 310 70 450 180 136 126 M 30 M 36 195 22336 CAKE4 1 740 000 H 2336 GS 36
170 SD 3038 S SD 3038 SG 290 170 470 36 46 250 560 220 50 340 120 85 75 M 24 M 30 87 23038 CAKE4 775 000 H 3038 GS 38
SD 538 SD 538 G 340 200 570 36 46 290 700 280 65 400 160 102 92 M 30 M 30 130 22238 CAKE4 1 140 000 H 3138 GS 38
SD 638 SD 638 G 400 240 680 43 59 330 820 320 70 475 190 142 132 M 30 M 36 210 22338 CAKE4 1 890 000 H 2338 GS 38
180 SD 3040 S SD 3040 SG 310 180 510 36 46 270 620 250 60 360 140 92 82 M 24 M 30 100 23040 CAKE4 940 000 H 3040 GS 40
SD 540 SD 540 G 360 210 610 36 46 300 740 290 65 420 170 108 98 M 30 M 30 155 22240 CAKE4 1 300 000 H 3140 GS 40
SD 640 SD 640 G 420 250 710 43 59 350 860 340 85 500 200 148 138 M 36 M 36 240 22340 CAKE4 2 000 000 H 2340 GS 40
200 SD 3044 S SD 3044 SG 340 200 570 36 46 290 700 280 65 400 160 100 90 M 30 M 30 130 23044 CAKE4 1 090 000 H 3044 GS 44
SD 544 SD 544 G 400 240 680 43 59 330 820 320 70 475 190 118 108 M 30 M 36 205 22244 CAKE4 1 570 000 H 3144 GS 44
SD 644 SD 644 G 460 280 770 43 59 360 920 350 85 550 210 155 145 M 36 M 36 315 22344 CAKE4 2 350 000 H 2344 GS 44
SD 548 SD 548 G 440 260 740 43 59 340 880 330 85 515 200 130 120 M 36 M 36 240 22248 CAKE4 1 870 000 H 3148 GS 48
SD 648 SD 648 G 500 300 830 50 67 390 990 380 100 590 230 165 155 M 36 M 42 405 22348 CAKE4 2 600 000 H 2348 GS 48
SD 3152 S SD 3152 SG 440 260 740 43 59 360 880 350 85 515 200 154 144 M 36 M 36 240 23152 CAKE4 2 160 000 H 3152 GS 52
SD 552 SD 552 G 480 280 790 43 59 370 940 360 85 560 210 140 130 M 36 M 36 315 22252 CAKE4 2 180 000 H 3152 GS 52
SD 652 SD 652 G 540 325 890 50 67 410 1 060 400 100 640 250 175 165 M 36 M 42 480 22352 CAKE4 3 100 000 H 2352 GS 52
SD 556 SD 556 G 500 300 830 50 67 390 990 380 100 590 230 140 130 M 36 M 42 390 22256 CAKE4 2 280 000 H 3156 GS 56
SD 656 SD 656 G 580 355 930 57 77 440 1 110 430 110 690 270 185 175 M 42 M 48 610 22356 CAKE4 3 500 000 H 2356 GS 56
Note (1) Including oil seal. Note (2) Applicable to the ZF Type with the same number.
To place an order for a complete unit, please specify, Plummer block bearing box+bearing+adapter.
Remarks 1. The threads for oil replenishing hole plugs are R 1/4 and those for drain plugs are R 3/8.
2. The plummer block bearing boxes listed above are provided with eye bolts.
B 312 B 313
B304-325E.indd 312-313 11/20/13 5:01:20 PM

LARGE-SIZE PLUMMER BLOCKS
SD 30 S, SD 31 S, SD 5 Types
A
t g
N1
Free-End
N
J 1 A1 H2 jDjd 1
s
H
Fixed-End
J H1
L g1
Shaft Dimensions Mass Applicable Parts Oil

Diameter Plummer Block (mm) (kg) Seals (2)
(mm) Bearing Box Numbers (1) Spherical Roller Bearing Adapter
d1 Free-End Fixed-End D H J N N1 A L A1 H1 H2 J1 g g1 t s Numbers Basic Dynamic Load Numbers
H8 h13 H13 H13 nominal nominal approx. Ratings Cr (N)
SD 560 SD 560 G 540 325 890 50 67 410 1 060 400 100 640 250 150 140 M 36 M 42 465 22260 CAKE4 2 610 000 H 3160 GS 60
SD 3164 S SD 3164 SG 540 325 890 50 67 430 1 060 400 100 640 250 186 176 M 36 M 42 480 23164 CAKE4 3 050 000 H 3164 GS 64
SD 564 SD 564 G 580 355 930 57 77 440 1 110 430 110 690 270 160 150 M 42 M 48 595 22264 CAKE4 2 990 000 H 3164 GS 64
320 SD 3068 S SD 3068 SG 520 310 860 50 67 400 1 020 370 100 615 230 143 133 M 36 M 42 410 23068 CAKE4 2 280 000 H 3068 GS 68
SD 3180 S SD 3180 SG 650 390 1 040 57 77 520 1 220 510 125 765 340 210 200 M 42 M 48 1 040 23180 CAKE4 4 150 000 H 3180 GS 80
SD 3184 S SD 3184 SG 700 420 1 070 57 77 560 1 250 550 135 830 380 234 224 M 48 M 48 1 150 23184 CAKE4 5 000 000 H 3184 GS 84
410 SD 3088 S SD 3088 SG 650 390 1 040 57 77 460 1 220 450 125 765 280 167 157 M 42 M 48 870 23088 CAKE4 3 150 000 H 3088 GS 88
430 SD 3092 S SD 3092 SG 680 405 1 040 57 77 470 1 220 460 130 790 310 173 163 M 48 M 48 940 23092 CAKE4 3 450 000 H 3092 GS 92
450 SD 3096 S SD 3096 SG 700 415 1 100 57 77 485 1 280 470 130 820 320 175 165 M 48 M 48 1 040 23096 CAKE4 3 800 000 H 3096 GS 96
To place an order for a complete unit, please specify, Plummer block bearing box+bearing+adapter.
B 314 B 315
B304-325E.indd 314-315 11/20/13 5:01:21 PM

DUSTPROOF PLUMMER BLOCKS
SG 5, SG 5-0 Types
A A2
g A
t 2
Width
N1 N1
Free-End
Outside Diameter
N
N J1 A1 H2 jD jd 1 jd 1
s
H
Fixed-End
J H1
Bolt Holes, 2 Places Bolt Holes, 4 Places X(2 ) X(2 )
L
Through Type End Cover Type Locating Ring
Shaft Plummer Block Dimensions Mass Applicable Parts Oil

Diameter Bearing Box (mm) (kg) Seals (3)
(mm) approx. Spherical Roller Bearing Adapter Locating Ring
Numbers (1)
d1 D H J N N1 A L A1 H1 H2 J1 A2 g t s Through End Cover Numbers Basic Dynamic Load Numbers Nominal (Outside Q'ty
Through Type End Cover Type H8 h13 H13 nominal nominal Type Type Ratings Cr (N) Dia.Width)
50 SG 511 SG 511-0 100 70 210 18 23 125 255 70 23 137 112.5 29 M 12 M 16 8.5 7.5 22211 EAKE4 119 000 H 311 X SR 1004 1 GS 11
55 SG 512 SG 512-0 110 80 230 18 23 145 290 80 25 160 135 32 M 16 M 16 15 14 22212 EAKE4 142 000 H 312 X SR 1104 1 GS 12
60 SG 513 SG 513-0 120 83 230 18 23 130 290 70 25 155 115 36 M 16 M 16 9.5 8.5 22213 EAKE4 177 000 H 313 X SR 1205 1 GS 13
65 SG 515 SG 515-0 130 90 230 18 23 135 290 80 25 168 120 36 M 16 M 16 12.5 11 22215 EAKE4 190 000 H 315 X SR 1305 1 GS 15
70 SG 516 SG 516-0 140 95 270 22 27 165 340 120 30 180 70 155 38 M 20 M 20 18.5 17 22216 EAKE4 212 000 H 316 X SR 1405 1 GS 16
75 SG 517 SG 517-0 150 100 280 22 27 170 350 120 30 190 70 160 41 M 20 M 20 21 20 22217 EAKE4 250 000 H 317 X SR 1505 1 GS 17
110 SG 524 SG 524-0 215 140 380 22 27 230 460 130 45 275 80 200 63 M 20 M 20 59 53 22224 EAKE4 550 000 H 3124 SR 2155 1 GS 24
115 SG 526 SG 526-0 230 150 410 26 32 240 490 160 45 295 80 220 69 M 24 M 24 67 62 22226 EAKE4 655 000 H 3126 SR 2305 1 GS 26
125 SG 528 SG 528-0 250 160 435 26 32 245 520 160 50 310 80 220 73 M 24 M 24 73 68 22228 CDKE4 645 000 H 3128 SR 2505 1 GS 28
160 SG 536 SG 536-0 320 190 600 33 42 325 690 190 55 400 110 285 91 M 30 M 30 155 135 22236 CDKE4 1 020 000 H 3136 SR 3205 1 GS 36
170 SG 538 SG 538-0 340 200 620 42 52 340 730 200 60 420 120 295 97 M 36 M 36 175 155 22238 CAKE4 1 140 000 H 3138 SR 3405 1 GS 38
180 SG 540 SG 540-0 360 210 635 42 52 350 750 210 60 445 130 310 103 M 36 M 36 210 180 22240 CAKE4 1 300 000 H 3140 SR 3605 1 GS 40
Note (1) Including oil seal. Notes (2) The X dimension indicates the offset of the bearing center from the center of plummer block bearing
To place an order for a complete unit, please specify, Plummer block bearing box+bearing+adapter+locating ring. box, and it is 1/2 of the locating ring width.
Remarks 1. The threads for grease nipples are R 1/8 for SG518 and under, and R 1/4 for SG520 and over. (3) Applicable to the ZF Type with the same number.
2. Bearing boxes larger than SG520 are provided with eye bolts.
B 316 B 317
B304-325E.indd 316-317 11/20/13 5:01:22 PM

STEPPED-SHAFT TYPE PLUMMER BLOCKS
SN 2 C, SN 3 C Types
A
Width
t g
N1 Free-End
Outside Diameter
N A1 jD jd 2 jd jd1
H2
s
H Fixed-End
J H1
L X(2 ) Locating Ring
Shaft Plummer Dimensions Mass Applicable Parts Oil Seals (3)

Diameter Block (mm) (kg)
(mm) Self-Aligning Ball Bearing Spherical Roller Bearing Nut Lock-washer Locating Ring
d Bearing Box1 d1 d2 D H J N N1 A L A1 H1 H2 g t s Numbers B. D. L. R. ( )
4
Numbers B. D. L. R. (4) Numbers Numbers Nominal (Outside Q'ty Side d 1 Side d 2
Numbers ( ) H8 h13 H13 nominal nominal approx. Cr (N) Cr (N) Dia.Width)
25 SN 205 C 30 20 52 40 130 15 20 67 165 46 22 75 25 M 8 M 12 1.1 1205 12 200 AN 05 AW 05X SR 52 5 2 GS 7 GS 5
2205 12 400 22205 CE4 37 500 AN 05 AW 05X SR 52 7 1
SN 305 C 30 20 62 50 150 15 20 80 185 52 22 90 34 M 8 M 12 1.6 1305 18 200 21305 CDE4 43 000 AN 05 AW 05X SR 62 8.5 2 GS 7 GS 5
2305 24 900 AN 05 AW 05X SR 62 10 1

2206 15 300 22206 CE4 50 000 AN 06 AW 06X SR 62 10 1
SN 306 C 35 25 72 50 150 15 20 82 185 52 22 95 37 M 10 M 12 1.8 1306 21 400 21306 CDE4 55 000 AN 06 AW 06X SR 72 9 2 GS 8 GS 6
2306 32 000 AN 06 AW 06X SR 72 10 1

2207 21 700 22207 CE4 69 000 AN 07 AW 07X SR 72 10 1
SN 307 C 45 30 80 60 170 15 20 90 205 60 25 110 41 M 10 M 12 2.6 1307 25 300 21307 CDE4 71 500 AN 07 AW 07X SR 80 10 2 GS 10 GS 7
2307 40 000 AN 07 AW 07X SR 80 10 1
40 SN 208 C 50 35 80 60 170 15 20 85 205 60 25 110 33 M 10 M 12 2.6 1208 19 300 AN 08 AW 08X SR 80 7.5 2 GS 11 GS 8

2208 22 400 22208 EAE4 90 500 AN 08 AW 08X SR 80 10 1
SN 308 C 50 35 90 60 170 15 20 95 205 60 25 115 43 M 10 M 12 2.9 1308 29 800 21308 EAE4 94 500 AN 08 AW 08X SR 90 10 2 GS 11 GS 8
2308 45 500 22308 EAE4 136 000 AN 08 AW 08X SR 90 10 1

2209 23 300 22209 EAE4 94 500 AN 09 AW 09X SR 85 8 1
SN 309 C 55 40 100 70 210 18 23 105 255 70 28 130 46 M 12 M 16 4.1 1309 38 500 21309 EAE4 119 000 AN 09 AW 09X SR 100 10.5 2 GS 12 GS 9
2309 55 000 22309 EAE4 166 000 AN 09 AW 09X SR 100 10 1

2210 23 400 22210 EAE4 99 000 AN 10 AW 10X SR 90 10 1
2310 65 000 22310 EAE4 197 000 AN 10 AW 10X SR 110 10 1
2211 26 700 22211 EAE4 119 000 AN 11 AW 11X SR 100 8 1
2311 76 500 22311 EAE4 234 000 AN 11 AW 11X SR 120 10 1
To place an order for a complete unit, please specify, Plummer block bearing box+bearing+nut+Lock-washer+locating ring. box. When one locating ring is used, it is 1/2 of the locating ring width, and when two rings are used, it
Remarks The threads for plugs are R 1/8. becomes 0.
(3) Applicable to the ZF Type with the same number. (4) B. D. L. R. : Basic Dynamic Load Ratings
B 318 B 319
B304-325E.indd 318-319 11/20/13 5:01:23 PM

A
Width
t g
N1 Free-End
Outside Diameter
N A1 jD jd 2 jd jd1
H2
s
H Fixed-End
J H1

4
2212 34 000 22212 EAE4 142 000 AN 12 AW 12X SR 110 10 1
2312 88 500 22312 EAE4 271 000 AN 12 AW 12X SR 130 10 1
2213 43 500 22213 EAE4 177 000 AN 13 AW 13X SR 120 12 1
2313 97 000 22313 EAE4 300 000 AN 13 AW 13X SR 140 10 1
2214 44 000 22214 EAE4 180 000 AN 14 AW 14X SR 125 13 1
SN 314 C 80 65 150 95 260 22 27 130 320 90 32 185 61 M 16 M 20 10 1314 65 000 21314 EAE4 250 000 AN 14 AW 14X SR 150 13 2 GS 18 GS 15
2314 111 000 22314 EAE4 340 000 AN 14 AW 14X SR 150 10 1
2215 44 500 22215 EAE4 190 000 AN 15 AW 15X SR 130 10 1
2315 125 000 22315 EAE4 390 000 AN 15 AW 15X SR 160 10 1
2216 49 000 22216 EAE4 212 000 AN 16 AW 16X SR 140 10 1
2316 130 000 22316 EAE4 435 000 AN 16 AW 16X SR 170 10 1
85 SN 217 C 95 80 150 95 260 22 27 125 320 90 32 185 46 M 16 M 20 10 1217 49 500 AN 17 AW 17X SR 150 9 2 GS 21 GS 18
2217 58 500 22217 EAE4 250 000 AN 17 AW 17X SR 150 10 1
SN 317 C 95 80 180 112 320 26 32 155 380 110 40 218 70 M 20 M 24 15 1317 98 500 21317 EAE4 289 000 AN 17 AW 17X SR 180 14.5 2 GS 21 GS 18
2317 142 000 22317 EAE4 480 000 AN 17 AW 17X SR 180 10 1
90 SN 218 C 100 85 160 100 290 22 27 145 345 100 35 195 62.4 M 16 M 20 13 1218 57 500 AN 18 AW 18X SR 160 16.2 2 GS 22 GS 19
2218 70 500 22218 EAE4 289 000 AN 18 AW 18X SR 160 11.2 2
23218 CE4 340 000 AN 18 AW 18X SR 160 10 1
SN 318 C 105 85 190 112 320 26 32 160 380 110 40 225 74 M 20 M 24 19 1318 117 000 21318 EAE4 330 000 AN 18 AW 18X SR 190 15.5 2 GS 23 GS 19
2318 154 000 22318 EAE4 535 000 AN 18 AW 18X SR 190 10 1
Remarks The threads for plugs are R 1/8 for SN316C, SN218C, and under and R 1/4 for SN317C and over. becomes 0.
(3) Applicable to the ZF Type with the same number. (4) B. D. L. R. : Basic Dynamic Load Ratings
B 320 B 321
B304-325E.indd 320-321 11/20/13 5:01:24 PM

A
Width
t g
N1 Free-End
Outside Diameter
N A1 jD jd 2 jd jd1
H2
s
H Fixed-End
J H1

4
95 SN 219 C 110 90 170 112 290 22 27 140 345 100 35 210 53 M 16 M 20 15 1219 64 000 AN 19 AW 19X SR 170 10.5 2 GS 24 GS 20
2219 84 000 22219 EAE4 330 000 AN 19 AW 19X SR 170 10 1
SN 319 C 110 90 200 125 350 26 32 170 410 120 45 245 77 M 20 M 24 22 1319 129 000 21319 CE4 345 000 AN 19 AW 19X SR 200 16 2 GS 24 GS 20
2319 161 000 22319 EAE4 590 000 AN 19 AW 19X SR 200 10 1
100 SN 220 C 115 95 180 112 320 26 32 160 380 110 40 218 70.3 M 20 M 24 18.5 1220 69 500 AN 20 AW 20X SR 180 18.1 2 GS 26 GS 21
2220 94 500 22220 EAE4 365 000 AN 20 AW 20X SR 180 12.1 2
23220 CE4 420 000 AN 20 AW 20X SR 180 10 1
SN 320 C 115 95 215 140 350 26 32 175 410 120 45 270 83 M 20 M 24 25 1320 140 000 21320 CE4 395 000 AN 20 AW 20X SR 215 18 2 GS 26 GS 21
2320 187 000 22320 EAE4 690 000 AN 20 AW 20X SR 215 10 1
110 SN 222 C 125 105 200 125 350 26 32 175 410 120 45 240 80 M 20 M 24 20 1222 87 000 AN 22 AW 22X SR 200 21 2 GS 28 GS 23
2222 122 000 22222 EAE4 485 000 AN 22 AW 22X SR 200 13.5 2
23222 CE4 515 000 AN 22 AW 22X SR 200 10 1
SN 322 C 125 105 240 150 390 28 36 190 450 130 50 300 90 M 24 M 24 32 1322 161 000 21322 CAE4 395 000 AN 22 AW 22X SR 240 20 2 GS 28 GS 23
2322 211 000 22322 EAE4 825 000 AN 22 AW 22X SR 240 10 1
120 SN 224 C 135 115 215 140 350 26 32 185 410 120 45 270 86 M 20 M 24 24.5 22224 EAE4 550 000 AN 24 AW 24 SR 215 14 2 GS 30 GS 26
23224 CE4 630 000 AN 24 AW 24 SR 215 10 1
SN 324 C 135 115 260 160 450 33 42 200 530 160 60 320 96 M 24 M 30 48 22324 EAE4 955 000 AN 24 AW 24 SR 260 10 1 GS 30 GS 26
130 SN 226 C 145 125 230 150 380 28 36 190 445 130 50 290 90 M 24 M 24 30 22226 EAE4 655 000 AN 26 AW 26 SR 230 13 2 GS 33 GS 28
23226 CE4 700 000 AN 26 AW 26 SR 230 10 1
SN 326 C 150 125 280 170 470 33 42 210 550 160 60 340 103 M 24 M 30 56 22326 CE4 995 000 AN 26 AW 26 SR 280 10 1 GS 34 GS 28
140 SN 228 C 155 135 250 150 420 33 42 205 500 150 50 305 98 M 24 M 30 38 22228 CDE4 645 000 AN 28 AW 28 SR 250 15 2 GS 35 GS 30
23228 CE4 835 000 AN 28 AW 28 SR 250 10 1
SN 328 C 160 135 300 180 520 35 45 235 610 170 65 365 112 M 30 M 30 72 22328 CE4 1 160 000 AN 28 AW 28 SR 300 10 1 GS 36 GS 30
150 SN 230 C 165 145 270 160 450 33 42 220 530 160 60 325 106 M 24 M 30 46 22230 CDE4 765 000 AN 30 AW 30 SR 270 16.5 2 GS 37 GS 33
23230 CE4 975 000 AN 30 AW 30 SR 270 10 1
SN 330 C 170 145 320 190 560 35 45 245 650 180 65 385 118 M 30 M 30 98 22330 CAE4 1 220 000 AN 30 AW 30 SR 320 10 1 GS 38 GS 33
160 SN 232 C 175 150 290 170 470 33 42 235 550 160 60 345 114 M 24 M 30 50 22232 CDE4 910 000 AN 32 AW 32 SR 290 17 2 GS 39 GS 34
23232 CE4 1 100 000 AN 32 AW 32 SR 290 10 1
SN 332 C 180 150 340 200 580 42 50 255 680 190 70 405 124 M 30 M 36 115 22332 CAE4 1 360 000 AN 32 AW 32 SR 340 10 1 GS 40 GS 34
Remarks 1. The threads for plugs are R 1/8 for SN219C, and R 1/4 for SN319C and SN220C and over. becomes 0.
2. Bearing boxes larger than SN320C and SN224C are provided with eye bolts. (3) Applicable to the ZF Type with the same number. (4) B. D. L. R. : Basic Dynamic Load Ratings
B 322 B 323
B304-325E.indd 322-323 11/20/13 5:01:24 PM

SD 2 C, SD 3 C Types
A
t g
N1
Free-End
N
J 1 A1 H2 jD jd 2 jd jd 1
s
H
Fixed-End
J H1
L g1
Shaft Plummer Block Dimensions Mass Applicable Parts Oil Seals (2)
Diameter Bearing Box (mm) (kg)
(mm) Spherical Roller Bearing Nut Lock-washer
Numbers (1)
d d1 d2 D H J N N1 A L A1 H1 H2 J1 g g1 t s Basic Dynamic Load or Stopper Side d 1 Side d 2
Free-End Fixed-End H8 h13 H13 H13 nominal nominal approx. Numbers Ratings Cr (N) Numbers Numbers
170 SD 234 C SD 234 CG 190 160 310 180 510 36 46 270 620 250 60 360 140 96 86 M 24 M 30 100 22234 CDE4 990 000 AN 34 AW 34 GS 42 GS 36
SD 334 C SD 334 CG 190 160 360 210 610 36 46 300 740 290 65 420 170 130 120 M 30 M 30 160 22334 CAE4 1 580 000 AN 34 AW 34 GS 42 GS 36
180 SD 236 C SD 236 CG 200 170 320 190 540 36 46 280 650 260 60 380 150 96 86 M 24 M 30 110 22236 CDE4 1 020 000 AN 36 AW 36 GS 44 GS 38
190 SD 238 C SD 238 CG 210 180 340 200 570 36 46 290 700 280 65 400 160 102 92 M 30 M 30 130 22238 CAE4 1 140 000 AN 38 AW 38 GS 46 GS 40
200 SD 240 C SD 240 CG 220 190 360 210 610 36 46 300 740 290 65 420 170 108 98 M 30 M 30 155 22240 CAE4 1 300 000 AN 40 AW 40 GS 48 GS 42
220 SD 244 C SD 244 CG 240 210 400 240 680 43 59 330 820 320 70 475 190 118 108 M 30 M 36 205 22244 CAE4 1 570 000 AN 44 AL 44 GS 52 GS 46
SD 344 C SD 344 CG 240 210 460 280 770 43 59 360 920 350 85 550 210 155 145 M 36 M 36 315 22344 CAE4 2 350 000 AN 44 AL 44 GS 52 GS 46
SD 348 C SD 348 CG 260 230 500 300 830 50 67 390 990 380 100 590 230 165 155 M 36 M 42 405 22348 CAE4 2 600 000 AN 48 AL 44 GS 56 GS 50
SD 352 C SD 352 CG 280 250 540 325 890 50 67 410 1 060 400 100 640 250 175 165 M 36 M 42 480 22352 CAE4 3 100 000 AN 52 AL 52 GS 60 GS 54
SD 356 C SD 356 CG 300 260 580 355 930 57 77 440 1 110 430 110 690 270 185 175 M 42 M 48 610 22356 CAE4 3 500 000 AN 56 AL 52 GS 64 GS 56
300 SD 260 C SD 260 CG 320 280 540 325 890 50 67 410 1 060 400 100 640 250 150 140 M 36 M 42 465 22260 CAE4 2 610 000 AN 60 AL 60 GS 68 GS 60
320 SD 264 C SD 264 CG 340 300 580 355 930 57 77 440 1 110 430 110 690 270 160 150 M 42 M 48 595 22264 CAE4 2 990 000 AN 64 AL 64 GS 72 GS 64
To place an order for a complete unit, please specify, Plummer block bearing box+bearing+nut+Lock-washer or stopper.
B 324 B 325
B304-325E.indd 324-325 11/20/13 5:01:25 PM

CYLINDRICAL ROLLER BEARINGS FOR SHEAVES
Open Type Bore Diameter 50 560mm B328
Prelubricated Type Bore Diameter 40 400mm B332

Cylindrical Roller Bearings for sheaves are specially designed thin-walled,
broad-width, full-complement type double-row cylindrical roller bearings, but
they are widely used also for general industrial machines running at low speed
and under heavy loads. There are several series as shown in Table 1.
Table 1 Series of Cylindrical Roller Bearings for Sheaves
Bearing Type Fixed-End Free-End

RS-48E4 RSF-48E4
Open Type Without Snap Ring
RS-49E4 RSF-49E4
Without Snap Ring RS-50

Shielded Type
With Snap Ring RS-50NR
Table 3 Since all are non-separable type bearings, the inner and outer rings cannot
Units : m
be separated, but the RSF type can be used as a free-end bearing. In this case,
Nominal Clearances
Bore Dia. the permissible axial displacement is listed in the bearing tables.
d (mm) CN C3 Since cylindrical roller bearings for sheaves are a double-row, full-
over incl. min. max. min. max. complement type, they can withstand heavy shock loads and moments and
have sufficient axial load capacity for use in sheaves.
30 40 15 50 35 70 Since the shielded type is a kind of bearing unit, the number of parts
40 50 20 55 40 75
surrounding the bearing can be reduced, so it allows for a simple compact
50 65 20 65 45 90
design.
65 80 25 75 55 105
The surface of these bearings is treated for rust prevention.
80 100 30 80 65 115
100 120 35 90 80 135 TOLERANCES AND
120 140 40 105 90 155
RUNNING ACCURACY Table 8.2 (Pages A60 to A63)
140 160 50 115 100 165
160 180 60 125 110 175 RECOMMENDED FITS AND INTERNAL CLEARANGES
180 200 65 135 125 195 When used with outer ring rotation for sheaves or wheels, the fit and radial
200 225 75 150 140 215 internal clearance should conform to Table 2.
225 250 90 165 155 230 Table 2 Fits and Internal Clearances for Cylindrical Roller Bearings for Sheaves
250 280 100 180 175 255
280 315 110 195 195 280 Fitting between Fitting between Outer Recommended
Operating Conditions
315 355 125 215 215 305 Inner Ring and Shaft Ring and Housing Bore Internal Clearance
Thin walled housings and heavy loads g6 or h6 P7 C3

355 400 140 235 245 340
400 450 155 275 270 390 Outer Ring
Normal to heavy loads g6 or h6 N7 C3
450 500 180 300 300 420 Rotation
Light or fluctuating loads g6 or h6 M7 CN
The fits listed in Tables 9.2 (Page A84) and 9.4 (Page A85) apply when
they are used with inner ring rotation in general applications, and the internal
clearance should conform to Table 3.
B 326 B 327
B326-333E.indd 326-327 11/20/13 5:01:43 PM

RS-48 RS-49 Types
RSF-48 RSF-49 Types
Bore Diameter 50 220 mm B B
4-d OH 4-d OH
r r ra
r r
ra
jD jd jD jd jDa jd a
Fixed-End Bearing Free-End Bearing

RS RSF
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers(1) Dimensions Abutment and Mass
(mm) (N) {kgf} (min 1) (mm) Fillet Dimensions (mm) (kg)
d D B r Cr C 0r Cr C 0r Grease Oil Fixed-End Bearing Free-End Bearing dOH(2) Axial da Da ra

min. Disp.(3) min. max. max. approx.
50 72 22 0.6 48 000 75 500 4 900 7 700 2 000 4 000 RS-4910E4 RSF-4910E4 2.5 1.5 54 68 0.6 0.30
60 85 25 1 68 500 118 000 6 950 12 000 1 600 3 200 RS-4912E4 RSF-4912E4 2.5 1.5 65 80 1 0.46
65 90 25 1 70 500 125 000 7 150 12 700 1 600 3 200 RS-4913E4 RSF-4913E4 2.5 2 70 85 1 0.50
70 100 30 1 102 000 168 000 10 400 17 200 1 400 2 800 RS-4914E4 RSF-4914E4 3 2 75 95 1 0.79
80 110 30 1 109 000 191 000 11 100 19 500 1 300 2 600 RS-4916E4 RSF-4916E4 3 2 85 105 1 0.89
90 125 35 1.1 147 000 268 000 15 000 27 400 1 100 2 200 RS-4918E4 RSF-4918E4 3 2 96.5 118.5 1 1.35
100 125 25 1 87 500 189 000 8 900 19 300 1 100 2 200 RS-4820E4 RSF-4820E4 2.5 1.5 105 120 1 0.74
140 40 1.1 194 000 400 000 19 800 41 000 1 000 2 000 RS-4920E4 RSF-4920E4 3 2 106.5 133.5 1 1.97
105 130 25 1 89 000 196 000 9 100 19 900 1 000 2 000 RS-4821E4 RSF-4821E4 2.5 1.5 110 125 1 0.77
145 40 1.1 199 000 420 000 20 300 43 000 950 1 900 RS-4921E4 RSF-4921E4 3 2 111.5 138.5 1 2.05
110 140 30 1 114 000 260 000 11 700 26 500 950 1 900 RS-4822E4 RSF-4822E4 3 2 115 135 1 1.09
150 40 1.1 202 000 430 000 20 600 44 000 900 1 800 RS-4922E4 RSF-4922E4 3 2 116.5 143.5 1 2.15
120 150 30 1 119 000 283 000 12 200 28 900 900 1 800 RS-4824E4 RSF-4824E4 3 2 125 145 1 1.28
165 45 1.1 226 000 480 000 23 100 49 000 800 1 600 RS-4924E4 RSF-4924E4 4 3 126.5 158.5 1 2.95
130 165 35 1.1 162 000 390 000 16 500 39 500 800 1 600 RS-4826E4 RSF-4826E4 3 2 136.5 158.5 1 1.9
180 50 1.5 262 000 555 000 26 700 56 500 750 1 500 RS-4926E4 RSF-4926E4 5 3.5 138 172 1.5 3.95
140 175 35 1.1 167 000 415 000 17 000 42 500 750 1 500 RS-4828E4 RSF-4828E4 3 2 146.5 168.5 1 2.03
190 50 1.5 272 000 595 000 27 700 60 500 710 1 400 RS-4928E4 RSF-4928E4 5 3.5 148 182 1.5 4.25
150 190 40 1.1 235 000 575 000 23 900 58 500 670 1 400 RS-4830E4 RSF-4830E4 3 2 156.5 183.5 1 2.85
210 60 2 390 000 865 000 40 000 88 500 670 1 300 RS-4930E4 RSF-4930E4 5 3.5 159 201 2 6.65
160 200 40 1.1 243 000 615 000 24 800 63 000 630 1 300 RS-4832E4 RSF-4832E4 3 2 166.5 193.5 1 3.05
220 60 2 410 000 930 000 41 500 95 000 600 1 200 RS-4932E4 RSF-4932E4 5 3.5 169 211 2 7.0
170 215 45 1.1 265 000 650 000 27 000 66 500 600 1 200 RS-4834E4 RSF-4834E4 4 3 176.5 208.5 1 4.1
230 60 2 415 000 975 000 42 500 99 500 600 1 200 RS-4934E4 RSF-4934E4 4 3.5 179 221 2 7.35
180 225 45 1.1 272 000 685 000 27 800 70 000 560 1 100 RS-4836E4 RSF-4836E4 4 3 186.5 218.5 1 4.3
250 69 2 495 000 1 130 000 50 500 115 000 530 1 100 RS-4936E4 RSF-4936E4 6 4.5 189 241 2 10.7
190 240 50 1.5 315 000 785 000 32 000 80 000 530 1 100 RS-4838E4 RSF-4838E4 5 3.5 198 232 1.5 5.65
260 69 2 510 000 1 180 000 52 000 120 000 500 1 000 RS-4938E4 RSF-4938E4 6 4.5 199 251 2 11.1
200 250 50 1.5 320 000 825 000 33 000 84 000 500 1 000 RS-4840E4 RSF-4840E4 5 3.5 208 242 1.5 5.95
280 80 2.1 665 000 1 500 000 68 000 153 000 480 950 RS-4940E4 RSF-4940E4 7 5 211 269 2 15.7
220 270 50 1.5 340 000 905 000 34 500 92 500 450 900 RS-4844E4 RSF-4844E4 5 3.5 228 262 1.5 6.45
300 80 2.1 695 000 1 620 000 70 500 165 000 430 850 RS-4944E4 RSF-4944E4 7 5 231 289 2 17
Remarks Cylindrical roller bearings for sheaves are designed for specific applications, when using them, please contact NSK. Notes (1) The suffix E4 indicates that the outer ring is provided with oil holes and oil groove.
(2) dOH represents the oil hole diameter in the outer ring.
(3) Permissible axial displacement for free-end bearings.
B 328 B 329
B326-333E.indd 328-329 11/20/13 5:01:43 PM

RS-48 RS-49 Types
RSF-48 RSF-49 Types
Bore Diameter 240 560 mm B B
4-d OH 4-d OH
r r ra
r r
ra
jD jd jD jd jDa jd a
Fixed-End Bearing Free-End Bearing

RS RSF
Boundary Dimensions Basic Load Ratings Limiting Speeds Bearing Numbers(1) Dimensions Abutment and Mass
(mm) (N) {kgf} (min 1) (mm) Fillet Dimensions (mm) (kg)
d D B r Cr C 0r Cr C 0r Grease Oil Fixed-End Bearing Free-End Bearing dOH(2) Axial da Da ra

min. Disp.(3) min. max. max. approx.
240 300 60 2 495 000 1 340 000 50 500 137 000 430 850 RS-4848E4 RSF-4848E4 5 3.5 249 291 2 10.3
320 80 2.1 725 000 1 770 000 74 000 181 000 400 800 RS-4948E4 RSF-4948E4 7 5 251 309 2 18.4
260 320 60 2 515 000 1 450 000 52 500 148 000 380 750 RS-4852E4 RSF-4852E4 5 3.5 269 311 2 11
360 100 2.1 1 050 000 2 530 000 107 000 258 000 360 710 RS-4952E4 RSF-4952E4 8 6 271 349 2 32
280 350 69 2 610 000 1 690 000 62 500 173 000 340 710 RS-4856E4 RSF-4856E4 6 4.5 289 341 2 16
380 100 2.1 1 090 000 2 720 000 111 000 277 000 340 670 RS-4956E4 RSF-4956E4 8 6 291 369 2 34
300 380 80 2.1 805 000 2 160 000 82 000 220 000 320 630 RS-4860E4 RSF-4860E4 6 5 311 369 2 23
420 118 3 1 460 000 3 400 000 149 000 350 000 300 600 RS-4960E4 RSF-4960E4 9 7 313 407 2.5 52
320 400 80 2.1 835 000 2 310 000 85 000 236 000 300 600 RS-4864E4 RSF-4864E4 6 5 331 389 2 24.3
440 118 3 1 500 000 3 600 000 153 000 365 000 280 560 RS-4964E4 RSF-4964E4 9 7 333 427 2.5 55
340 420 80 2.1 855 000 2 430 000 87 500 248 000 280 560 RS-4868E4 RSF-4868E4 6 5 351 409 2 25.6
460 118 3 1 560 000 3 900 000 159 000 395 000 260 530 RS-4968E4 RSF-4968E4 9 7 353 447 2.5 58
360 440 80 2.1 885 000 2 580 000 90 000 264 000 260 530 RS-4872E4 RSF-4872E4 6 5 371 429 2 27
480 118 3 1 600 000 4 050 000 163 000 415 000 260 500 RS-4972E4 RSF-4972E4 9 7 373 467 2.5 61
380 480 100 2.1 1 260 000 3 600 000 128 000 365 000 240 500 RS-4876E4 RSF-4876E4 8 6 391 469 2 45.5
520 140 4 2 040 000 5 200 000 209 000 530 000 240 450 RS-4976E4 RSF-4976E4 11 8 396 504 3 90.5
400 500 100 2.1 1 290 000 3 750 000 132 000 385 000 240 480 RS-4880E4 RSF-4880E4 8 6 411 489 2 47.5
540 140 4 2 100 000 5 450 000 214 000 555 000 220 450 RS-4980E4 RSF-4980E4 11 8 416 524 3 94.5
420 520 100 2.1 1 320 000 3 950 000 135 000 405 000 220 450 RS-4884E4 RSF-4884E4 8 6 431 509 2 49.5
560 140 4 2 150 000 5 700 000 219 000 580 000 200 430 RS-4984E4 RSF-4984E4 11 8 436 544 3 98.5
440 540 100 2.1 1 350 000 4 150 000 138 000 420 000 200 430 RS-4888E4 RSF-4888E4 8 6 451 529 2 51.5
600 160 4 2 840 000 7 350 000 289 000 750 000 190 380 RS-4988E4 RSF-4988E4 11 8 456 584 3 136
460 580 118 3 1 730 000 5 150 000 177 000 525 000 190 380 RS-4892E4 RSF-4892E4 9 7 473 567 2.5 77.5
620 160 4 2 870 000 7 500 000 293 000 765 000 190 380 RS-4992E4 RSF-4992E4 11 8 476 604 3 142
480 600 118 3 1 760 000 5 300 000 180 000 545 000 190 380 RS-4896E4 RSF-4896E4 9 7 493 587 2.5 80.5
650 170 5 3 200 000 8 500 000 325 000 865 000 180 360 RS-4996E4 RSF-4996E4 12 9 500 630 4 167
500 620 118 3 1 810 000 5 600 000 184 000 570 000 180 360 RS-48/500E4 RSF-48/500E4 9 7 513 607 2.5 83.5
670 170 5 3 300 000 8 900 000 335 000 910 000 170 340 RS-49/500E4 RSF-49/500E4 12 9 520 650 4 173
530 710 180 5 3 400 000 9 200 000 350 000 935 000 160 320 RS-49/530E4 RSF-49/530E4 12 11 550 690 4 206
560 750 190 5 3 800 000 10 100 000 385 000 1 030 000 150 300 RS-49/560E4 RSF-49/560E4 12 11 580 730 4 231
Remarks Cylindrical roller bearings for sheaves are designed for specific applications, when using them, please contact NSK. Notes (1) The suffix E4 indicates that the outer ring is provided with oil holes and oil groove.
(2) dOH represents the oil hole diameter in the outer ring.
(3) Permissible axial displacement for free-end bearings.
B 330 B 331
B326-333E.indd 330-331 11/20/13 5:01:44 PM

RS-50 Type (Prelubricated)
C
S + 0.4
C C1 0 f
r r
30 30
Cx Cx
B B
jD jd jD jd jD 2 jD x jd a
4-d OH 4-d OH
Without Locating Ring With Locating Ring
Boundary Dimensions Basic Load Ratings Limiting Bearing Numbers Locating Ring Oil Holes Abutment and Mass
(mm) (N) {kgf} Speeds Dimensions (mm) (mm) Fillet Dimensions (mm) (kg)
1
(min )
d D B C Cx(1) r Cr C 0r Cr C 0r Grease Without Locating Ring With Locating Ring C1 S D2 f dOH da Dx
min. min. min. min. approx.
40 68 38 37 0.4 0.6 79 500 116 000 8 100 11 800 2 400 RS-5008 RS-5008NR 28 4.5 71.8 2 2.5 43.5 77.5 0.56
45 75 40 39 0.4 0.6 95 500 144 000 9 750 14 700 2 200 RS-5009 RS-5009NR 30 4.5 78.8 2 2.5 48.5 84.5 0.70
50 80 40 39 0.4 0.6 100 000 158 000 10 200 16 100 2 000 RS-5010 RS-5010NR 30 4.5 83.8 2 2.5 53.5 89.5 0.76
55 90 46 45 0.6 0.6 118 000 193 000 12 100 19 700 1 800 RS-5011 RS-5011NR 34 5.5 94.8 2.5 3 60 101 1.17
60 95 46 45 0.6 0.6 123 000 208 000 12 600 21 200 1 700 RS-5012 RS-5012NR 34 5.5 99.8 2.5 3 65 106 1.25
65 100 46 45 0.6 0.6 128 000 224 000 13 100 22 800 1 600 RS-5013 RS-5013NR 34 5.5 104.8 2.5 3 70 111 1.32
70 110 54 53 0.6 0.6 171 000 285 000 17 500 29 000 1 400 RS-5014 RS-5014NR 42 5.5 114.5 2.5 3 75 121 1.87
75 115 54 53 0.6 0.6 179 000 305 000 18 200 31 500 1 400 RS-5015 RS-5015NR 42 5.5 119.5 2.5 3 80 126 2.0
80 125 60 59 0.6 0.6 251 000 430 000 25 600 43 500 1 200 RS-5016 RS-5016NR 48 5.5 129.5 2.5 3 85 136 2.65
85 130 60 59 0.6 0.6 256 000 445 000 26 200 45 500 1 200 RS-5017 RS-5017NR 48 5.5 134.5 2.5 3 90 141 2.75
90 140 67 66 1 0.6 305 000 540 000 31 000 55 000 1 100 RS-5018 RS-5018NR 54 6 145.4 2.5 4 96 153.5 3.75
95 145 67 66 1 0.6 310 000 565 000 32 000 57 500 1 100 RS-5019 RS-5019NR 54 6 150.4 2.5 4 101 158.5 3.95
100 150 67 66 1 0.6 320 000 585 000 32 500 59 500 1 000 RS-5020 RS-5020NR 54 6 155.4 2.5 4 106 163.5 4.05
110 170 80 79 1.1 1 385 000 695 000 39 000 71 000 900 RS-5022 RS-5022NR 65 7 175.4 2.5 5 116.5 183.5 6.1
120 180 80 79 1.1 1 400 000 750 000 40 500 76 500 850 RS-5024 RS-5024NR 65 7 188 3 5 126.5 197 7.0
130 200 95 94 1.1 1 535 000 1 000 000 54 500 102 000 750 RS-5026 RS-5026NR 77 8.5 207 3 5 136.5 217 10.6
140 210 95 94 1.1 1 550 000 1 040 000 56 000 106 000 710 RS-5028 RS-5028NR 77 8.5 217 3 5 146.5 227 11.3
150 225 100 99 1.3 1 620 000 1 210 000 63 500 124 000 670 RS-5030 RS-5030NR 81 9 232 3 6 157 242 13.7
160 240 109 108 1.3 1.1 695 000 1 370 000 71 000 140 000 630 RS-5032 RS-5032NR 89 9.5 247 3 6 167 257 16.8
170 260 122 121 1.3 1.1 860 000 1 680 000 88 000 171 000 600 RS-5034 RS-5034NR 99 11 270 4 6 177 285 22.2
180 280 136 135 1.3 1.1 980 000 1 910 000 100 000 195 000 530 RS-5036 RS-5036NR 110 12.5 294 5 6 187 318 30
190 290 136 135 1.3 1.1 1 120 000 2 230 000 114 000 227 000 500 RS-5038 RS-5038NR 110 12.5 304 5 6 197 328 32
200 310 150 149 1.3 1.1 1 310 000 2 650 000 133 000 270 000 480 RS-5040 RS-5040NR 120 14.5 324 5 6 207 352 41
220 340 160 159 1.5 1.1 1 510 000 3 100 000 154 000 320 000 430 RS-5044 RS-5044NR 130 14.5 356 6 7 228.5 382 53
240 360 160 159 1.5 1.1 1 570 000 3 350 000 160 000 340 000 400 RS-5048 RS-5048NR 130 14.5 376 6 7 248.5 402 57
260 400 190 189 2 1.5 2 130 000 4 500 000 217 000 460 000 360 RS-5052 RS-5052NR 154 17.5 416 7 8 270 444 86
280 420 190 189 2 1.5 2 170 000 4 700 000 221 000 480 000 340 RS-5056 RS-5056NR 154 17.5 436 7 8 290 472 92
300 460 218 216 2 1.5 2 670 000 5 850 000 272 000 600 000 300 RS-5060 RS-5060NR 178 19 476 7 8 310 512 130
320 480 218 216 2 1.5 2 720 000 6 100 000 277 000 620 000 300 RS-5064 8 330 135
340 520 243 241 2.1 2 3 350 000 7 550 000 345 000 770 000 260 RS-5068 10 352 185
360 540 243 241 2.1 2 3 450 000 7 850 000 350 000 800 000 260 RS-5072 10 372 192
380 560 243 241 2.1 2 3 550 000 8 400 000 365 000 855 000 240 RS-5076 10 392 196
400 600 272 270 2.1 2 4 250 000 9 950 000 435 000 1 010 000 220 RS-5080 10 412 280
Note (1) Chamfer dimension of inner ring in radial direction. Remarks 3. Cylindrical roller bearings for sheaves are designed for specific applications, when using them, please contact NSK.
Remarks 1. Good quality grease is prepacked in bearings. 4. For shield with outside diameter larger than 180mm, the above figure is different actual shape. For detail drawing,
2. Grease can be supplied through oil holes in the inner rings. please contact NSK.
B 332 B 333
B326-333E.indd 332-333 11/20/13 5:01:45 PM

ROLL-NECK BEARINGS
FOUR-ROW
TAPERED ROLLER BEARINGS
Bore Diameter 100 939.800mm B338
FOUR-ROW

Four-row tapered roller bearings and four-row cylindrical roller bearings used
for rolling-mill roll necks are easy to service and check, and are designed to
have the highest load rating possible for the limited space around roll necks.
Also, they are designed for high speed to satisfy the demand for fast rolling.
In addition to the open type (KV) four-row tapered roller bearings listed
in this catalog, sealed-clean type four-row tapered roller bearings are also
available. Please refer to Large-Size Rolling Bearings catalog (CAT. No. E125)
or Extra-Capacity Sealed-CleanTM Roll Neck Bearings catalog (CAT. No.
E1225) for more detailed information.
TOLERANCES AND RUNNING ACCURACY
METRIC DESIGN FOUR-ROW

TAPERED ROLLER BEARINGS Table 8.3 (Pages A64 to A67)
INCH DESIGN FOUR-ROW
TAPERED ROLLER BEARINGS Table 8.4 (Pages A68 to A69)
FOUR-ROW
CYLINDRICAL ROLLER BEARINGS Table 8.2 (Pages A60 to A63)
(Not applicable to combined width)
RECOMMENDED FITS
FOUR-ROW TAPERED ROLLER BEARINGS (CYLINDRICAL BORES)
Tables 1 and 2 apply to metric series bearings and Tables 3 and 4 to inch
design.
Table 1 Fits of Metric Design Four-Row Tapered Roller Bearings with Roll Necks
Units : m
Nominal Bore Single Plane Mean Wear
Diameter Bore Dia. Deviation Tolerance Clearance Limits
d (mm) & dmp
over incl. high low high low min. max. Ref.
80 120 0 20 120 150 100 150 300

120 180 0 25 150 175 125 175 350
180 250 0 30 175 200 145 200 400
250 315 0 35 210 250 175 250 500
315 400 0 40 240 300 200 300 600
400 500 0 45 245 300 200 300 600
500 630 0 50 250 300 200 300 600
630 800 0 75 325 400 250 400 800
B 334 B 335
B334-343E.indd 334-335 11/20/13 5:02:01 PM

Table 2 Fits of Metric Design Four-Row Tapered Roller Bearings with Chock FOUR-ROW CYLINDRICAL ROLLER BEARINGS (CYLINDRICAL BORES)
Units : m When they are used on backup rolls of four stage rolling mills, the tolerances for roll
Nominal Outside Single Plane Mean Tolerance for neck diameters are shown in Table 5. For the fitting between the bearing and chock
Wear Limits of
Diameter Outside Dia. Deviation Chock Bore Clearance Chock bore, we recommend G7.
D (mm) & Dmp Diameter For the fitting of four-row cylindrical roller bearings on the roll necks of other rolling
over incl. high low high low min. max. Ref. mills, Table 9.2 (Page A84) and Table 9.4 (Page A85) usually apply.
120 150 0 18 + 57 +25 25 75 150 Table 5 Recommended Backup Roll Neck Tolerances
150 180 0 25 +100 +50 50 125 250
180 250 0 30 +120 +50 50 150 300 Units : m
250 315 0 35 +115 +50 50 150 300 Nominal Bore Diameter Tolerances for
315 400 0 40 +110 +50 50 150 300 d Roll Neck Diameter
400 500 0 45 +105 +50 50 150 300 over incl. high low
500 630 0 50 +100 +50 50 150 300 280 355 +0.165 +0.13
630 800 0 75 +150 +75 75 225 450 355 400 +0.19 +0.15
800 1 000 0 100 +150 +75 75 250 500 400 450 +0.22 +0.17
450 500 +0.25 +0.19
500 560 +0.28 +0.21
560 630 +0.32 +0.25
630 710 +0.35 +0.27
710 800 +0.39 +0.31
Table 3 Fits of Inch Design Four-Row Tapered Roller Bearings with Roll Necks 800 900 +0.44 +0.35
900 1 000 +0.48 +0.39
Units : m
Bore Diameter Tolerance for Roll Wear
Nominal Bore Diameter d Deviation & ds Neck Diameter Clearance INTERNAL CLEARANCES
Limits of
over incl. Roll Neck
high low high low min. max. FOUR-ROW TAPERED ROLLER BEARINGS
(mm) 1/25.4 (mm) 1/25.4 Ref.
The radial internal clearances in four-row tapered roller bearings (cylindrical bores)
152.400 6.0000 203.200 8.0000 + 25 0 150 175 150 200 400 used on rolling mill roll necks with a loose fit are C2 or often smaller than C2. The
203.200 8.0000 304.800 12.0000 + 25 0 175 200 175 225 450 NSK standard clearances for four-row tapered roller bearings for roll necks are
304.800 12.0000 609.600 24.0000 + 51 0 200 250 200 301 600
shown in Table 6. Depending on the operating conditions, special radial clearance
609.600 24.0000 914.400 36.0000 + 76 0 250 325 250 401 800 selection may become necessary, please contact NSK in such a case.
914.400 36.0000 +102 0 300 400 300 502 1 000 The internal clearance in four-row tapered roller bearings is peadjusted for individual
bearing sets, therefore it is necessary to use each part of a given set by observing
mating marks when assembling them.
FOUR-ROW CYLINDRICAL ROLLER BEARINGS

Table 4 Fits of Inch Design Four-Row Tapered Roller Bearings with Chocks
Please contact NSK regarding internal clearance.
Units : m
Outside Dia. Tolerance for Chock Wear
Nominal Outside Diameter D Deviation & Ds Bore Diameter Clearance
Limits of
Chock Table 6 Standard Radial Internal Clearances in Four-
over incl. Row Tapered Roller Bearings (Cylindrical
high low high low min. max.
(mm) 1/25.4 (mm) 1/25.4 Ref. Bores)
Units : m
304.800 12.0000 + 25 0 + 75 + 50 25 75 150
304.800 12.0000 609.600 24.0000 + 51 0 +150 +100 49 150 300 Nominal Bore Diameter Radial Internal Clearance
609.600 24.0000 914.400 36.0000 + 76 0 +225 +150 74 225 450 d (mm)
914.400 36.0000 1 219.200 48.0000 +102 0 +300 +200 98 300 600 over incl. min. max.
1 219.200 48.0000 1 524.000 60.0000 +127 0 +375 +250 123 375 750 80 120 25 45
120 180 30 50
180 250 40 60
250 315 50 70
315 400 60 80
400 500 70 90
500 630 80 100
630 800 100 120
800 1 000 120 140
B 336 B 337
B334-343E.indd 336-337 11/20/13 5:02:02 PM

FOUR-ROW TAPERED ROLLER BEARINGS
Bore Diameter 100 939.800 mm
C4
ra
rb
B4
jD jd jDa jd a
Boundary Dimensions Basic Load Ratings Abutment and Fillet Dimensions Mass
(mm) (N) {kgf} (mm) (kg)
Bearing Numbers Reference Numbers
d D B4 C4 Cr C 0r Cr C 0r da Da ra rb
max. max. approx.
100 140 104 104 320 000 765 000 32 500 78 000 100 KV 895 109 130 2 1.5 4.9
120 170 124 124 475 000 1 080 000 48 000 110 000 120 KV 895 131 158 2 2 8.5
135 180 160 160 455 000 1 280 000 46 500 130 000 135 KV 1802 145 169 1.5 2 11.1
150 212 155 155 750 000 1 880 000 76 500 192 000 150 KV 895 162 196 2 2 17
165.100 225.425 165.100 168.275 705 000 2 160 000 72 000 220 000 *165 KV 2252 178 209 3.3 0.8 20.2 46791D -720-721D
177.800 247.650 192.088 192.088 950 000 2 570 000 97 000 262 000 *177 KV 2452 192 228 3.3 1.5 27.9 67791D -720-721D
190.500 266.700 187.325 188.912 1 010 000 2 870 000 103 000 293 000 *190 KV 2651 204 246 3.3 1.5 32.8 67885D -820-820D
206.375 282.575 190.500 190.500 995 000 2 870 000 101 000 292 000 *206 KV 2854 218 261 3.3 0.8 35.2 67986D -920-921D
228.600 400.050 296.875 296.875 2 570 000 5 450 000 262 000 555 000 *228 KV 4051 264 367 3.3 3.3 152 EE 529091D -157-158XD
240 338 248 248 1 960 000 5 300 000 199 000 540 000 240 KV 895 257 315 2.5 2.5 68.5
244.475 327.025 193.675 193.675 1 300 000 3 700 000 132 000 375 000 *244 KV 3251 260 306 3.3 1.5 44.6 LM 247748D -710-710D
254.000 358.775 269.875 269.875 2 230 000 6 150 000 227 000 630 000 *254 KV 3551 272 335 3.3 1.5 85.6 M 249748DW -710-710D
266.700 355.600 230.188 228.600 1 810 000 5 050 000 185 000 515 000 *266 KV 3552 281 335 3.3 1.5 60.6 LM 451349D -310-310D
279.400 393.700 269.875 269.875 2 010 000 5 450 000 205 000 555 000 *279 KV 3951 302 363 6.4 1.5 100 EE 135111D -155-156XD
304.648 438.048 280.990 279.400 2 600 000 6 750 000 265 000 685 000 *304 KV 4353 329 407 4.8 3.3 133 M 757448DW -410-410D
343.052 457.098 254.000 254.000 2 520 000 7 250 000 256 000 740 000 *343 KV 4555 362 430 3.3 1.5 114 LM 761649DW -610-610D
368.300 523.875 382.588 382.588 5 050 000 14 900 000 515 000 1 520 000 *368 KV 5251 396 487 6.4 3.3 274 HM 265049D -010-010D
384.175 546.100 400.050 400.050 5 750 000 16 600 000 585 000 1 700 000 *384 KV 5452 417 510 6.4 3.3 309 HM 266449D -410-410D
406.400 546.100 288.925 288.925 2 960 000 8 550 000 300 000 875 000 *406 KV 5455 430 512 6.4 1.5 186 LM 767749DW -710-710D
415.925 590.550 434.975 434.975 6 450 000 19 500 000 655 000 1 990 000 *415 KV 5951 451 550 6.4 3.3 395 M 268749D -710-710D
457.200 596.900 276.225 279.400 3 300 000 10 000 000 335 000 1 020 000 *457 KV 5952 487 566 3.3 1.5 201 L 770849DW -810-810D
479.425 679.450 495.300 495.300 8 200 000 25 500 000 840 000 2 600 000 *479 KV 6751 520 635 6.4 3.3 595 M 272749DW -710-710D
482.600 615.950 330.200 330.200 4 100 000 13 800 000 415 000 1 410 000 *482 KV 6152 508 582 6.4 3.3 242 LM 272249DW -210-210D
500 705 515 515 8 350 000 26 600 000 850 000 2 710 000 500 KV 895 544 657 5 5 654
509.948 654.924 377.000 379.000 4 700 000 16 100 000 480 000 1 640 000 *509 KV 6551 536 619 6.4 1.5 312
558.800 736.600 409.575 409.575 6 050 000 19 400 000 620 000 1 980 000 *558 KV 7352 588 697 6.4 3.3 457 LM 377449DW -410-410D
571.500 812.800 593.725 593.725 11 700 000 37 000 000 1 200 000 3 800 000 *571 KV 8151 622 755 6.4 3.3 1 020 M 278749DW -710-710D
609.600 787.400 361.950 361.950 5 750 000 18 700 000 585 000 1 910 000 *609 KV 7851 A 644 745 6.4 3.3 454 EE 649241DW -310-311D
635 900 660 660 13 300 000 43 500 000 1 350 000 4 400 000 635 KV 9001 695 840 5 4 1 380
685.800 876.300 352.425 355.600 6 350 000 22 200 000 645 000 2 270 000 *685 KV 8751 730 833 6.4 3.3 543 EE 655271DW -345-346D
711.200 914.400 317.500 317.500 5 500 000 19 300 000 560 000 1 970 000 *711 KV 9151 770 870 6.4 3.3 549 EE 755281DW -360-361D
749.300 990.600 605.000 605.000 13 000 000 47 000 000 1 330 000 4 800 000 *749 KV 9951 804 940 6.4 3.3 1 310 LM 283649DW -610-610D
762.000 1 066.800 723.900 736.600 18 000 000 59 500 000 1 840 000 6 050 000 *762 KV 1051 828 996 12.7 5 2 100
840.000 1 170.000 840.000 840.000 22 200 000 76 000 000 2 260 000 7 750 000 *840 KV 1151 910 1 095 7 7 2 900
939.800 1 333.500 952.500 952.500 26 900 000 92 000 000 2 740 000 9 400 000 *939 KV 1351 1 035 1 245 12.7 4.8 4 380 LM 287849DW -810-810D
Note (*) Bearings marked * are inch design.

Remarks 1. For four-row tapered roller bearings not listed above, please contact NSK.
2. Four-row tapered roller bearings are designed for specific applications, when using them, please contact NSK.
B 338 B 339
B334-343E.indd 338-339 11/20/13 5:02:02 PM

C2 C2
r2 r2
r1 r1
B B2
jD jFW jd jD jF jd
W
Figure 1 Figure 2
Boundary Dimensions Basic Load Ratings Mass

(mm) (N) {kgf} (kg) Reference
Bearing Numbers Figures Bearing
d D B, B 2 C2 Fw r1 r2 Cr C 0r Cr C 0r Numbers
min. min. approx.
100 140 104 104 111 1.5 1.1 345 000 820 000 35 000 84 000 100 RV 1401 4 2
145 225 156 156 169 2 2 835 000 1 820 000 85 000 185 000 145 RV 2201 23 1 313924A
150 220 150 150 168 2 2 770 000 1 700 000 78 500 174 000 150 RV 2201 20 1
230 156 156 174 2 2 825 000 1 810 000 84 500 185 000 150 RV 2302 23 1 313891A
160 230 130 130 178 2 2 665 000 1 340 000 68 000 136 000 160 RV 2301 16 1
230 168 168 180 2 2 895 000 2 200 000 91 500 225 000 160 RV 2302 22 1
170 250 168 168 192 2.1 2.1 1 040 000 2 320 000 106 000 237 000 170 RV 2501 27 1
255 180 180 193 2.1 2.1 1 130 000 2 500 000 115 000 255 000 170 RV 2503 31 1
180 250 156 156 200 2 2 880 000 2 230 000 89 500 227 000 180 RV 2501 23 1
260 168 168 202 2.1 2.1 990 000 2 300 000 101 000 235 000 180 RV 2601 29 1 313812
190 260 168 168 212 2 2 980 000 2 600 000 100 000 265 000 190 RV 2601 26 1
270 200 200 212 2.1 2.1 1 260 000 3 100 000 128 000 315 000 190 RV 2701 36 1 314199B
200 280 200 200 224 2.1 2.1 1 210 000 3 200 000 123 000 325 000 200 RV 2801 38 1
290 192 192 226 2.1 2.1 1 220 000 3 000 000 124 000 305 000 200 RV 2901 42 1 313811
220 310 192 192 247 2.1 2.1 1 320 000 3 450 000 134 000 350 000 220 RV 3101 46 1
310 225 225 245 2.1 2.1 1 500 000 3 900 000 153 000 395 000 220 RV 3102 52 1
320 210 210 248 2.1 2.1 1 530 000 3 650 000 156 000 375 000 220 RV 3201 56 1
230 330 206 206 260 2.1 2.1 1 510 000 3 900 000 154 000 395 000 230 RV 3301 58 1 313824
340 260 260 261 3 3 2 050 000 5 100 000 209 000 520 000 230 RV 3401 81 1
240 330 220 220 270 3 3 1 520 000 4 400 000 155 000 445 000 240 RV 3301 57 1 313921
250 350 220 220 278 3 3 1 660 000 4 200 000 169 000 430 000 250 RV 3501 64 1
260 370 220 220 292 3 3 1 760 000 4 450 000 179 000 455 000 260 RV 3701 76 1 313823
380 280 280 294 3 3 2 420 000 6 250 000 247 000 635 000 260 RV 3801 107 1
270 380 230 230 298 2.1 2.1 2 000 000 5 050 000 204 000 515 000 270 RV 3801 83 1
280 390 220 220 312 3 3 1 820 000 4 800 000 186 000 490 000 280 RV 3901 80 1 313822
300 400 300 300 328 2 2 2 330 000 6 900 000 238 000 700 000 300 RV 4021 103 2
420 240 240 332 3 3 2 280 000 5 750 000 233 000 585 000 300 RV 4201 101 1
310 430 240 240 344.5 3 3 2 240 000 5 950 000 228 000 605 000 310 RV 4301 107 1
320 450 240 240 355 3 3 2 320 000 5 750 000 237 000 585 000 320 RV 4502 116 1
330 460 340 340 365 4 4 3 050 000 8 650 000 310 000 880 000 330 RV 4601 174 1
Remarks 1. For four-row cylindrical roller bearings not listed above, please contact NSK.
2. Four-row cylindrical roller bearings are designed for specific applications, when using them, please contact NSK.
B 340 B 341
B334-343E.indd 340-341 11/20/13 5:02:03 PM

C2 C2 C4 C4
r2 r2 r2
r2
r1 r1 r1 r1
B B2 B2 B2
jD jFW jd jD jF jd jD jFW jd jD jFW jd
W
Figure 1 Figure 2 Figure 3 Figure 4
Boundary Dimensions Basic Load Ratings Mass

(mm) (N) {kgf} (kg) Reference
Bearing Numbers Figures Bearing
d D B, B 2 C2 Fw r1 r2 Cr C 0r Cr C 0r Numbers
min. min. approx.
370 540 400 400 415 4 4 4 500 000 12 000 000 460 000 1 230 000 370 RV 5401 311 1
380 540 400 400 424 5 5 4 300 000 12 000 000 440 000 1 220 000 380 RV 5401 280 1( 1)
390 550 400 400 434 5 5 4 400 000 12 400 000 450 000 1 260 000 390 RV 5521 303 2( 1)
400 560 410 410 445 5 2 5 600 000 16 500 000 575 000 1 680 000 400 RV 5611 315 3 313015
430 591 420 420 476 4 4 4 450 000 13 400 000 455 000 1 370 000 430 RV 5921 347 2
440 620 450 450 490 4 4 6 350 000 19 000 000 650 000 1 940 000 440 RV 6221 430 2
450 630 450 450 500 4 4 5 950 000 17 500 000 605 000 1 780 000 450 RV 6321 440 2
460 670 500 500 522 6 6 7 650 000 22 700 000 780 000 2 320 000 460 RV 6721 596 2( 1)
480 680 500 500 534 5 5 7 700 000 23 100 000 785 000 2 360 000 480 RV 6811 610 3
500 690 510 510 552 5 5 7 750 000 24 600 000 790 000 2 500 000 500 RV 6921 580 2( 1)
700 515 515 554 5 5 7 800 000 23 800 000 800 000 2 430 000 500 RV 7021 622 2( 1)
720 530 530 560 6 6 8 550 000 25 300 000 870 000 2 580 000 500 RV 7211 782 3
520 735 535 535 574.5 5 5 8 900 000 26 300 000 910 000 2 680 000 520 RV 7331 750 4
530 780 570 570 601 6 6 10 100 000 29 200 000 1 030 000 2 980 000 530 RV 7811 960 3
570 815 594 594 628 6 6 11 700 000 33 500 000 1 190 000 3 450 000 570 RV 8111 960 3
610 870 660 660 680 6 6 13 200 000 41 500 000 1 340 000 4 250 000 610 RV 8711 1 330 3
650 920 690 690 723 7.5 7.5 14 200 000 45 000 000 1 450 000 4 600 000 650 RV 9211 1 520 3
690 980 715 715 767.5 7.5 7.5 15 300 000 48 000 000 1 560 000 4 900 000 690 RV 9831 1 790 4
700 930 620 620 763 6 6 11 100 000 38 000 000 1 130 000 3 900 000 700 RV 9311 1 200 3
980 700 700 774 6 6 15 300 000 49 000 000 1 560 000 5 000 000 700 RV 9821 1 720 2( 1)
725 1 000 700 700 796 6 6 15 600 000 51 000 000 1 590 000 5 200 000 725 RV 1011 1 670 3
760 1 080 805 790 845 6 6 19 000 000 61 000 000 1 940 000 6 200 000 760 RV 1032 2 430 4
800 1 080 750 750 880 6 6 16 000 000 56 500 000 1 630 000 5 750 000 800 RV 1032 2 050 4
820 1 160 840 840 911 7.5 7.5 21 900 000 71 500 000 2 230 000 7 300 000 820 RV 1121 2 900 2( 1)
1 100 745 720 892 6 3 16 900 000 58 500 000 1 720 000 6 000 000 820 RV 1132 2 000 4
850 1 180 850 850 940 7.5 7.5 21 100 000 72 000 000 2 150 000 7 350 000 850 RV 1111 2 850 3
860 1 130 670 670 934 6 6 15 700 000 56 500 000 1 600 000 5 800 000 860 RV 1132 1 780 4
1 160 735 710 940 7.5 4 17 500 000 60 000 000 1 780 000 6 100 000 860 RV 1133 2 200 4
900 1 230 895 870 985 7.5 7.5 22 100 000 76 000 000 2 250 000 7 750 000 900 RV 1211 3 200 3
920 1 280 865 850 1 015 7.5 7.5 24 000 000 80 000 000 2 450 000 8 150 000 920 RV 1211 3 510 3
Remarks 1. For four-row cylindrical roller bearings not listed above, please contact NSK. Note (1) Oil holes and oil grooves are provided at the center of outer rings.
2. Four-row cylindrical roller bearings are designed for specific applications, when using them, please contact NSK.
B 342 B 343
B334-343E.indd 342-343 11/20/13 5:02:04 PM

Railway Rolling Stock Bearings
Railway rolling stock bearings are important components of rolling stocks that require high
reliability.
The main bearings consist of axle bearings that are mounted at both ends of axle and
support the entire weight of the rolling stock. Additionally, there are railway traction motor
bearings that are used for the motor that drives the axle; and gear unit bearings that transfer
the power from the motor to the axle. NSK has designed and manufactured specific bearings
for these very applications.
Types and Features

Axle Bearings
Axle bearings consist of the following types of bearings to meet operator demands for
high-speed capability of rolling stock, weight reductions, and minimal maintenance and
inspection requirements:
Cylindrical roller bearings with a thrust collar (oil bath lubrication, grease lubrication)
Tapered roller bearings (oil bath lubrication)
Sealed-clean rotating end cap cylindrical roller bearings(grease lubrication)
Sealed-clean rotating end cap tapered roller bearings (grease lubrication)
NSK has been approved by AAR (Association of American Railroads).
Traction Motor Bearings
Bearings for inverter controlled AC motors are speciality designed to meet high-speed
specifications and requirements for ensuring dimensional stability. NSK recommends long-
life grease for these bearings.
NSK offers the following bearings as a measure against electric erosion, which occurs
when electric current is allowed to flow through the motor bearings:
Ceramic-insulated bearings (ceramic-coated bearings) and PPS-insulated bearings
High capacity bearings also available for locomotive-type large traction motors
Gear Unit Bearings

Axle Bearings
These bearings are designed to meet high-speed specifications and offer excellent seizure
resistance.
A reinforced cage has been adopted for these bearings.
Specified catalogs
Bearings for Railway Rolling Stock CAT. No. E1156
Axle Bearings for Railway Rolling Stock (Cylindrical Roller Bearings) CAT. No. E1239
Axle Bearings for Railway Rolling Stock (Spherical Roller Bearings) CAT. No. E1240
Bearings for Traction Motors CAT. No. E1241
Traction Motor Bearings Gear Unit Bearings
B 344 B 345
STEEL BALLS AND ROLLERS
STEEL BALLS
FOR BALL BEARINGS Nominal Diameter 0.3 114.3mm B348
CYLINDRICAL ROLLERS
FOR ROLLER BEARINGS Nominal Diameter 3 80mm B350
LONG CYLINDRICAL ROLLERS
FOR ROLLER BEARINGS Nominal Diameter 5.5 15mm B352
NEEDLE ROLLERS
FOR ROLLER BEARINGS Nominal Diameter 1 5mm B354
B 346 B 347
B346-355E.indd 346-347 11/20/13 5:02:37 PM

STEEL BALLS FOR BALL BEARINGS
SjDw
Nominal Size, Basic Diameters, and Mass Application, Nominal Size, Tolerances, Roughness, and Gauges
Units : m
Tolerances(1) Gauges
Basic Mass (kg) Basic Mass (kg) Basic Mass (kg)
Diameter per Diameter per Diameter per Class Variation Sphericity Roughness Diameter
Nominal Size Nominal Size Nominal Size Difference Gauge
Dw 10000 pcs Dw 1000 pcs Dw 10 pcs in Dia. Ra Gauge
(mm) approx. (mm) approx. (mm) approx. per Lot Interval
max. max. max. max.
0.3 mm 0.30000 0.0011 3/8 9.52500 3.523 30 mm 30.00000 1.101 G 3 0.08 0.08 0.010 0.13 0.5 5, TT, 0.5, 0, + 0.5, TT, + 5
0.4 mm 0.40000 0.0026 10 mm 10.00000 4.076 1 3/ 16 30.16250 1.119
0.5 mm 0.50000 0.0051 13/32 10.31875 4.479 1 1/4 31.75000 1.305 G 5 0.13 0.13 0.014 0.25 1 5, TT, 1 , 0, + 1 , TT, + 5
0.6 mm 0.60000 0.0088 11 mm 11.00000 5.425 32 mm 32.00000 1.336 G 10 0.25 0.25 0.020 0.5 1 9, TT, 1 , 0, + 1 , TT, + 9
0.025 0.63500 0.0104 7/16 11.11250 5.594 1 5/ 16 33.33750 1.510 G 16 0.4 0.4 0.025 0.8 2 10, TT, 2 , 0, + 2 , TT, +10
0.7 mm 0.70000 0.0140 11.5 mm 11.50000 6.199 34 mm 34.00000 1.602
G 20 0.5 0.5 0.032 1 2 10, TT, 2 , 0, + 2 , TT, +10
1/32 0.79375 0.0204 15/32 11.90625 6.880 1 3/8 34.92500 1.736
0.8 mm 0.80000 0.0209 12 mm 12.00000 7.044 35 mm 35.00000 1.748 G 24 0.6 0.6 0.040 1.2 2 12, TT, 2 , 0, + 2 , TT, +12
1 mm 1.00000 0.0408 1/2 12.70000 8.350 36 mm 36.00000 1.902 G 28 0.7 0.7 0.050 1.4 2 12, TT, 2 , 0, + 2 , TT, +12
3/64 1.19062 0.0688 13 mm 13.00000 8.955 1 7/ 16 36.51250 1.984 G 40 1 1 0.060 2 4 16, TT, 4 , 0, + 4 , TT, +16
1.2 mm 1.20000 0.0704 17/32 13.49375 10.02 38 mm 38.00000 2.237
1.5 mm 1.50000 0.1376 14 mm 14.00000 11.19 1 1/2 38.10000 2.254 G 60 1.5 1.5 0.080 3 6 18, TT, 6 , 0, + 6 , TT, +18
1/16 1.58750 0.1631 9/16 14.28750 11.89 1 9/ 16 39.68750 2.548 G 100 2.5 2.5 0.100 5 10 40, TT, 10 , 0, +10 , TT, +40
5/64 1.98438 0.3185 15 mm 15.00000 13.76 40 mm 40.00000 2.609 G 200 5 5 0.150 10 15 60, TT, 15 , 0, +15 , TT, +60
2 mm 2.00000 0.3261 19/32 15.08125 13.98 1 5/8 41.27500 2.866
3/32 2.38125 0.5504 5/8 15.87500 16.31 1 11/ 16 42.86250 3.210 Note (1) The values do not take into account surface defects; hence measurement shall be taken outside such defects.
2.5 mm 2.50000 0.6369 16 mm 16.00000 16.70 1 3/4 44.45000 3.580
7/64 2.77812 0.8740 21/32 16.66875 18.88 45 mm 45.00000 3.714
3 mm 3.00000 1.101 17 mm 17.00000 20.03 1 13/ 16 46.03750 3.977 Hardness
1/8 3.17500 1.305 11/16 17.46250 21.71 1 7/8 47.62500 4.403
3.5 mm 3.50000 1.748 18 mm 18.00000 23.77 1 15/ 16 49.21250 4.858 Hardness
9/64 3.57188 1.858 23/32 18.25625 24.80 50 mm 50.00000 5.095 Nominal Size
HV HRC
5/32 3.96875 2.548 19 mm 19.00000 27.96 2 50.80000 5.344
4 mm 4.00000 2.609 3/4 19.05000 28.18 2 1/8 53.97500 6.410 0.3 mm ~ 3 mm 772~900 (63~67)(1)
4.5 mm 4.50000 3.714 25/32 19.84375 31.85 55 mm 55.00000 6.782 1/8 ~ 30 mm 62~67
3/16 4.76250 4.403 20 mm 20.00000 32.61 2 1/4 57.15000 7.609
5 mm 5.00000 5.095 13/16 20.63750 35.83 60 mm 60.00000 8.805 1 3/16 ~ 4 61~67
5.5 mm 5.50000 6.782 21 mm 21.00000 37.75 2 3/8 60.32500 8.948 Note (1) Values in ( ) are converted values for reference.
7/32 5.55625 7.016 27/32 21.43125 40.12 2 1/2 63.50000 10.44 Remarks A column blue letter of Nominal Size is inch dimensions.
15/64 5.95312 8.600 22 mm 22.00000 43.40 65 mm 65.00000 11.19
6 mm 6.00000 8.805 7/8 22.22500 44.75 2 5/8 66.67500 12.08
1/4 6.35000 10.44 23 mm 23.00000 49.60 2 3/4 69.85000 13.89
6.5 mm 6.50000 11.19 29/32 23.01875 49.72 2 7/8 73.02500 15.87
17/64 6.74688 12.52 15/16 23.81250 55.04 3 76.20000 18.04
7 mm 7.00000 13.98 24 mm 24.00000 56.35 3 1/4 82.55000 22.93
9/32 7.14375 14.86 31/32 24.60625 60.73 3 1/2 88.90000 28.64
7.5 mm 7.50000 17.20 25 mm 25.00000 63.69 3 3/4 95.25000 35.23
5/16 7.93750 20.38 1 25.40000 66.80 4 101.60000 42.75
8 mm 8.00000 20.87 26 mm 26.00000 71.64
8.5 mm 8.50000 25.03 1 1/ 16 26.98750 80.12
11/32 8.73125 27.13 28 mm 28.00000 89.48
9 mm 9.00000 29.72 1 1/8 28.57500 95.11
B 348 Remarks A column blue letter of Nominal Size is corresponding inch dimensions (reference). B 349
B346-355E.indd 348-349 11/20/13 5:02:40 PM

CYLINDRICAL ROLLERS FOR ROLLER BEARINGS
Tolerances for Cylindrical Roller Chamfers

Units : mm
min. max.
0.1 0.3 Units : mm

jD w 0.2 0.5
0.3 0.8
Mass (kg)
0.5 1.2 r
r r 0.6 1.5 Nominal Size DW LW per 100 pcs
0.7 1.7 min.
approx.
1 2.2(1)
r r 1.5 3.5 42 42 42 42 1 45
2 4
Lw 45 45 45 45 1 55.5
Note (1) If D W exceeds 40 mm,
r (max.) is 2.7 mm.
48 48 48 48 1 67
Units : mm Units : mm
50 50 50 50 1 76
r
Mass (kg)
r
Mass (kg) 52 52 52 52 1.5 85
Nominal Size DW LW per 100 pcs Nominal Size DW LW per 100 pcs
min. min. 54 54 54 54 1.5 95.5
approx. approx.
56 56 56 56 1.5 107
3 3 3 3 0.1 0.016 15 15 15 15 0.5 2.04
3 5 3 5 0.1 0.027 15 22 15 22 0.5 3.0 60 60 60 60 1.5 131
3.5 5 3.5 5 0.2 0.037 16 16 16 16 0.5 2.48 64 64 64 64 1.5 159
16 24 16 24 0.5 3.75
4 4 4 4 0.2 0.039
4 6 4 6 0.2 0.058 17 17 17 17 0.5 2.97 68 68 68 68 1.5 191
4 8 4 8 0.2 0.078 17 24 17 24 0.5 4.2
18 18 18 18 0.5 3.55 75 75 75 75 2 256
4.5 4.5 4.5 4.5 0.2 0.055
4.5 6 4.5 6 0.2 0.073 18 26 18 26 0.5 5.1 80 80 80 80 2 310
5 5 5 5 0.2 0.075 19 19 19 19 0.6 4.16
5 8 5 8 0.2 0.121 19 28 19 28 0.6 6.1
5 10 5 10 0.2 0.152 20 20 20 20 0.6 4.85
20 30 20 30 0.6 7.3
5.5 5.5 5.5 5.5 0.2 0.10
5.5 8 5.5 8 0.2 0.146 21 21 21 21 0.6 5.6
21 30 21 30 0.6 8.0
6 6 6 6 0.2 0.13
6 8 6 8 0.2 0.178 22 22 22 22 0.6 6.4
6 12 6 12 0.2 0.261 22 34 22 34 0.6 10
6.5 6.5 6.5 6.5 0.3 0.166 23 23 23 23 0.6 7.4
6.5 9 6.5 9 0.3 0.23 23 34 23 34 0.6 11.2
Accuracy of Cylindrical Rollers
24 24 24 24 0.6 8.4
7 7 7 7 0.3 0.206 24 36 24 36 0.6 12.6 Units : m
7 10 7 10 0.3 0.296
7 14 7 14 0.3 0.415 25 25 25 25 0.7 9.5 Out-of- Single Plane Mean Roller Gauge (3 ) Roller Gauge End Face
25 36 25 36 0.7 13.7 DW Length Deviation
Roundness Roller Diameter Lot Diameter Lot Length Runout
7.5 7.5 7.5 7.5 0.3 0.254 (mm) (1) Variation(2) Variation(1)
&LWS
7.511 7.5 11 0.3 0.375 26 26 26 26 0.7 10.7 Class Variation
26 40 26 40 0.7 16.4 &R VDWmp VDWL VLWL SW
8 8 8 8 0.3 0.31 over incl. max. max. max. high low(4) max. max.
8 12 8 12 0.3 0.465 28 28 28 28 0.7 13.3
28 44 28 44 0.7 21 1 3 18 0.5 0.8 1 +10 [ ( I T 9) 10] 5 3
9 9 9 9 0.3 0.44 30 30 30 30 0.7 16.3
9 14 9 14 0.3 0.68 30 48 30 48 0.7 26.2
1A 3 30 0.7 1 1.5 +10 [ ( I T 9) 10] 7 5
10 10 10 10 0.3 0.60 2 3 50 1 1.5 2 +10 [ ( I T 9) 10] 10 6
32 32 32 32 1 19.9
10 14 10 14 0.3 0.85 32 52 32 52 1 32.5 2A 10 80 1.3 2 2.5 +10 [ ( I T 9) 10] 13 8
11 11 11 11 0.3 0.81 34 34 34 34 1 23.9 3 18 80 1.5 3 3 +10 [ ( I T 9) 10] 15 10
11 15 11 15 0.3 1.1 34 55 34 55 1 38.5 5 30 80 2.5 4 5 +10 [ ( I T 9) 10] 25 15
12 12 12 12 0.3 1.04 36 36 36 36 1 28.3 Notes (1) Applicable to roller center (length direction).
12 18 12 18 0.3 1.57 36 58 36 58 1 45.5 (2) Applicable to cylindrical outside surface.
13 13 13 13 0.3 1.33 38 38 38 38 1 33.5 (3) To find the IT9 standard tolerance according to the LW size classification, refer to the IT9 column of the Appendix Table 11
13 20 13 20 0.3 2.04 38 62 38 62 1 55 on Page C22.
14 14 14 14 0.3 1.66 40 40 40 40 1 39 (4) The value for low of length deviation is subtracted 10 m from the value of the standard tolerance for each roller length.
14 20 14 20 0.3 2.38 40 65 40 65 1 63
B 350 B 351
B346-355E.indd 350-351 11/20/13 5:02:41 PM

LONG CYLINDRICAL ROLLERS FOR ROLLER BEARINGS
jD w
r r Tolerances for Long Cylindrical Roller Chamfers
Units : mm
r r min. max.
Lw
0.2 0.5
Remarks The figure shows an example of a flat-end long cylindrical roller.
0.3 0.8
0.5 1.2
Mass (kg) Mass (kg)

r (1) r (1)
Nominal Size DW LW per 100 pcs Nominal Size DW LW per 100 pcs
min. min. Accuracy of Long Cylindrical Rollers
approx. approx.
Units : m
5.518 5.5 18 0.2 0.333 8 25 8 25 0.3 0.978 Out-of- Single Plane Mean Roller Gauge Length
5.522.4 5.5 22.4 0.2 0.414 8 31.5 8 31.5 0.3 1.23 Roundness Roller Diameter Lot Diameter Deviation(2)
5.528 5.5 28 0.2 0.518 8 40 8 40 0.3 1.56 (1)
8 50 8 50 0.3 1.96 Class Variation (3) Variation(1)
8 63 8 63 0.3 2.46 &R VDWmp VDWL &LWS
6 20 6 20 0.2 0.44 max. max. max.
6 25 6 25 0.2 0.55 9 28 9 28 0.3 1.39 3 1.5 3 3 h12
6 31.5 6 31.5 0.2 0.693 9 35.5 9 35.5 0.3 1.76
6 40 6 40 0.2 0.88 9 45 9 45 0.3 2.23
6 50 6 50 0.2 1.1 9 56 9 56 0.3 2.77 5 2 5 5 h12
Notes (1) Applicable to roller center (length direction).
6.520 6.5 20 0.3 0.516 1031.5 10 31.5 0.3 1.93 (2) Classified by LW. Refer to Tolerauce for Length Doviation.
6.525 6.5 25 0.3 0.645 1040 10 40 0.3 2.44 (3) Applicable to cylindrical outside surface.
6.531.5 6.5 31.5 0.3 0.813 1050 10 50 0.3 3.06
1063 10 63 0.3 3.85
7 22.4 7 22.4 0.3 0.671
7 28 7 28 0.3 0.838 1240 12 40 0.3 3.52
7 35.5 7 35.5 0.3 1.06 1250 12 50 0.3 4.4
1263 12 63 0.3 5.54
7 45 7 45 0.3 1.35
7 56 7 56 0.3 1.68
1545 15 45 0.5 6.16 Tolerance for Length Deviation
1556 15 56 0.5 7.68
7.531.5 7.5 31.5 0.3 1.08 1571 15 71 0.5 9.74 Units : mm
7.540 7.5 40 0.3 1.38 1590 15 90 0.5 12.4
Length h12 h13
Note (1) Only for flat-end rollers.
3 6 0 0.18
6 10 0 0.22
10 18 0 0.27
18 30 0 0.21 0 0.33
30 50 0 0.25 0 0.39
50 80 0 0.30
80 120 0 0.35
B 352 B 353
B346-355E.indd 352-353 11/20/13 5:02:42 PM

NEEDLE ROLLERS FOR ROLLER BEARINGS
jD w jDw
r r
Lw r r
Lw
Spherical-end Type Flat-end Type
Units : mm Units : mm Tolerances for Needle Roller Chamfers

Units : mm
Mass (kg) Mass (kg)
r (1) r (1)
Nominal Size DW LW per 1000 pcs Nominal Size DW LW per 1000 pcs DW
min. min. r r
approx. approx.
over incl. min. max.
1 5.8 1 5.8 0.1 0.035 3.519.8 3.5 19.8 0.1 1.50
1 6.8 1 6.8 0.1 0.042 3.521.8 3.5 21.8 0.1 1.65
1 7.8 1 7.8 0.1 0.048 3.523.8 3.5 23.8 0.1 1.80 1 0.1 0.4
1 9.8 1 9.8 0.1 0.060 3.525.8 3.5 25.8 0.1 1.95
1.5 5.8 1.5 5.8 0.1 0.080 3.527.8 3.5 27.8 0.1 2.10 1 3 0.1 0.6
1.5 6.8 1.5 6.8 0.1 0.093 3.529.8 3.5 29.8 0.1 2.25
1.5 7.8 1.5 7.8 0.1 0.105 3.531.8 3.5 31.8 0.1 2.40 3 5 0.1 0.9
1.5 9.8 1.5 9.8 0.1 0.135 3.534.8 3.5 34.8 0.1 2.60
1.511.8 1.5 11.8 0.1 0.160 4 13.8 4 13.8 0.1 1.35 Remarks Only for flat-end needle rollers.
1.513.8 1.5 13.8 0.1 0.190 4 15.8 4 15.8 0.1 1.55
2 6.8 2 6.8 0.1 0.165 4 17.8 4 17.8 0.1 1.75
2 7.8 2 7.8 0.1 0.190 4 19.8 4 19.8 0.1 1.95
2 9.8 2 9.8 0.1 0.240 4 21.8 4 21.8 0.1 2.15
2 11.8 2 11.8 0.1 0.290 4 23.8 4 23.8 0.1 2.35
2 13.8 2 13.8 0.1 0.335 4 25.8 4 25.8 0.1 2.55
2 15.8 2 15.8 0.1 0.385 4 27.8 4 27.8 0.1 2.70
2 17.8 2 17.8 0.1 0.435 4 29.8 4 29.8 0.1 2.90
2 19.8 2 19.8 0.1 0.485 4 31.8 4 31.8 0.1 3.10
2.5 7.8 2.5 7.8 0.1 0.300 4 34.8 4 34.8 0.1 3.40
2.5 9.8 2.5 9.8 0.1 0.375 4 37.8 4 37.8 0.1 3.70
2.511.8 2.5 11.8 0.1 0.450 4 39.8 4 39.8 0.1 3.90 Accuracy of Needle Rollers
2.513.8 2.5 13.8 0.1 0.525 4.517.8 4.5 17.8 0.1 2.20
2.515.8 2.5 15.8 0.1 0.605 4.519.8 4.5 19.8 0.1 2.45 Units : m
2.517.8 2.5 17.8 0.1 0.680 4.521.8 4.5 21.8 0.1 2.70
2.519.8 2.5 19.8 0.1 0.755 4.523.8 4.5 23.8 0.1 2.95 Single Plane Mean Out-of- Roller Gauge Length
2.521.8 2.5 21.8 0.1 0.835 4.525.8 4.5 25.8 0.1 3.20 Roller Diameter Roundness (1) Lot Diameter Deviation(2)
2.523.8 2.5 23.8 0.1 0.910 4.529.8 4.5 29.8 0.1 3.70 Class Variation ( )
1
Variation(1)
3 9.8 3 9.8 0.1 0.540 4.531.8 4.5 31.8 0.1 3.95 VDWP &R VDWL &LWS
3 11.8 3 11.8 0.1 0.650 4.534.8 4.5 34.8 0.1 4.30 max. max. max.
3 13.8 3 13.8 0.1 0.760 4.537.8 4.5 37.8 0.1 4.70
3 15.8 3 15.8 0.1 0.870 4.539.8 4.5 39.8 0.1 4.90
3 17.8 3 17.8 0.1 0.980 5 19.8 5 19.8 0.1 3.00 2 1 1 2 h13
3 19.8 3 19.8 0.1 1.10 5 21.8 5 21.8 0.1 3.35
3 21.8 3 21.8 0.1 1.20 5 23.8 5 23.8 0.1 3.65
3 23.8 3 23.8 0.1 1.30 3 1.5 1.5 3 h13
5 25.8 5 25.8 0.1 3.95
3 25.8 3 25.8 0.1 1.40 5 27.8 5 27.8 0.1 4.25
3 27.8 3 27.8 0.1 1.55 5 29.8 5 29.8 0.1 4.55 5 2 2.5 5 h13
3 29.8 3 29.8 0.1 1.65 5 31.8 5 31.8 0.1 4.85
3.511.8 3.5 11.8 0.1 0.885 5 34.8 5 34.8 0.1 5.30 Notes 1
( ) Applicable to roller center (length direction).
3.513.8 3.5 13.8 0.1 1.05 5 37.8 5 37.8 0.1 5.75
3.515.8 3.5 15.8 0.1 1.20 5 39.8 5 39.8 0.1 6.10 (2) Classified by LW. Refer to Tolerance for Length Deviation in Page
3.517.8 3.5 17.8 0.1 1.35 5 49.8 5 49.8 0.1 7.60 B353.
Remarks The actual diameter at any place along the entire length should
Note (1) Only for flat-end rollers. not exceed the following figures compared to the actual maximum
Remarks 1. The figure shows a spherical-end type and a flat-end type. diameter at the roller center (length direction).
2. The radius R of the spherical-end type is bounded by the following range: Class2: 0.5m
Minimum: DW/2 Class3: 0.8m
B 354 Maximum: LW/2 Class5: 1.0m B 355
B346-355E.indd 354-355 11/20/13 5:02:43 PM

ACCESSORIES FOR ROLLING BEARINGS
ADAPTERS
FOR ROLLING BEARINGS Shaft Diameter 17 470mm B358
WITHDRAWAL SLEEVES
FOR ROLLING BEARINGS Shaft Diameter 35 480mm B366
NUTS FOR ROLLING BEARINGS B372

STOPPERS FOR ROLLING BEARINGS B377
LOCK-WASHERS FOR ROLLING BEARINGS B378
B 356 B 357
B356-379E.indd 356-357 11/20/13 5:03:01 PM

ADAPTERS FOR ROLLING BEARINGS
Shaft Diameter 17 40 mm Shaft Diameter 45 60 mm
B5 B5
B2 B2 A B2 B2 A
B2 B2
B1 B1 B1 b jd B1 B1 B1 b jd
jd 1jd 2 jd 1 jd2 jd 1 jd 2 jd e jK jd 1jd 2 jd 1 jd2 jd 1 jd 2 jd e jK
Nominal Dimensions Abutment Dimensions Mass Nominal Dimensions Abutment Dimensions Mass
Shaft Bearing (mm) Adapter (mm) (kg) Shaft Bearing (mm) Adapter (mm) (kg)
Diameter Bore Dia. Nominal Numbers Sleeve Diameter Bore Dia. Nominal Numbers Sleeve
(mm) (mm) B1 d2 B2 B5 Numbers A K de b (mm) (mm) B1 d2 B2 B5 Numbers A K de b
d1 d Applicable Bearings min. min. min. min. approx. d1 d Applicable Bearings min. min. min. min. approx.
17 20 1204K + H 204X 24 32 7 A 204X 14 39 23 5 0.045 45 50 1210K + H 210X 35 70 12 A 210X 19 76 53 5 0.275

20 2204K + H 304X 28 32 7 A 304X 14 39 24 5 0.045 50 2210K + H 310X 42 70 12 A 310X 19 76 54 10 0.30
20 1304K + H 304X 28 32 7 A 304X 14 39 24 8 0.045 50 1310K + H 310X 42 70 12 A 310X 19 76 54 5 0.30
20 2304K + H 2304X 31 32 7 A 2304X 14 39 24 5 0.050
50 21310E AKE4 + H 310X 42 70 12 A 310X 19 76 54 5 0.30
20 25 1205K + H 205X 26 38 8 A 205X 15 45 28 5 0.065 50 2310K + H 2310X 55 70 12 A 2310X 19 76 56 5 0.35
25 2205K + H 305X 29 38 8 A 305X 15 45 29 5 0.075 50 22310E AKE4 + H 2310X 55 70 12 A 2310X 19 76 56 5 0.35
25 1305K + H 305X 29 38 8 A 305X 15 45 29 6 0.075
25 21305C DKE4 + H 305X 29 38 8 A 305X 15 45 29 6 0.075 50 55 1211K + H 211X 37 75 12 A 211X 19 85 60 6 0.305
25 2305K + H 2305X 35 38 8 A 2305X 15 45 29 5 0.090 55 2211K + H 311X 45 75 12 A 311X 19 85 60 11 0.35
55 22211E AKE4 + H 311X 45 75 12 A 311X 19 85 60 11 0.35
25 30 1206K + H 206X 27 45 8 A 206X 15 50 33 5 0.10
30 2206K + H 306X 31 45 8 A 306X 15 50 34 5 0.11 55 1311K + H 311X 45 75 12 A 311X 19 85 60 6 0.35
30 1306K + H 306X 31 45 8 A 306X 15 50 34 6 0.11 55 21311E AKE4 + H 311X 45 75 12 A 311X 19 85 60 6 0.35
55 2311K + H 2311X 59 75 12 A 2311X 19 85 61 6 0.40
30 21306C DKE4 + H 306X 31 45 8 A 306X 15 50 34 6 0.11 55 22311E AKE4 + H 2311X 59 75 12 A 2311X 19 85 61 6 0.40
30 2306K + H 2306X 38 45 8 A 2306X 15 50 35 5 0.125
55 60 1212K + H 212X 38 80 13 A 212X 20 90 64 5 0.365
30 35 1207K + H 207X 29 52 9 A 207X 17 58 38 5 0.125
60 2212K + H 312X 47 80 13 A 312X 20 90 65 9 0.40
35 2207K + H 307X 35 52 9 A 307X 17 58 39 5 0.145
60 22212E AKE4 + H 312X 47 80 13 A 312X 20 90 65 9 0.40
35 1307K + H 307X 35 52 9 A 307X 17 58 39 7 0.145
35 21307C DKE4 + H 307X 35 52 9 A 307X 17 58 39 7 0.145 60 1312K + H 312X 47 80 13 A 312X 20 90 65 5 0.40
35 2307K + H 2307X 43 52 9 A 2307X 17 58 40 5 0.16 60 21312E AKE4 + H 312X 47 80 13 A 312X 20 90 65 5 0.40
60 2312K + H 2312X 62 80 13 A 2312X 20 90 66 5 0.45
35 40 1208K + H 208X 31 58 10 A 208X 17 65 44 5 0.175 60 22312E AKE4 + H 2312X 62 80 13 A 2312X 20 90 66 5 0.45
40 2208K + H 308X 36 58 10 A 308X 17 65 44 5 0.19
40 1308K + H 308X 36 58 10 A 308X 17 65 44 5 0.19 60 65 1213K + H 213X 40 85 14 A 213X 21 96 70 5 0.40
65 2213K + H 313X 50 85 14 A 313X 21 96 70 8 0.45
40 21308E AKE4 + H 308X 36 58 10 A 308X 17 65 44 5 0.19 65 22213E AKE4 + H 313X 50 85 14 A 313X 21 96 70 8 0.45
40 2308K + H 2308X 46 58 10 A 2308X 17 65 45 5 0.225
40 22308E AKE4 + H 2308X 46 58 10 A 2308X 17 65 45 5 0.225 65 1313K + H 313X 50 85 14 A 313X 21 96 70 5 0.45
40 45 1209K + H 209X 33 65 11 A 209X 17 72 49 5 0.225 65 21313E AKE4 + H 313X 50 85 14 A 313X 21 96 70 5 0.45
45 2209K + H 309X 39 65 11 A 309X 17 72 49 8 0.26 65 2313K + H 2313X 65 85 14 A 2313X 21 96 72 5 0.55
45 1309K + H 309X 39 65 11 A 309X 17 72 49 5 0.26 65 22313E AKE4 + H 2313X 65 85 14 A 2313X 21 96 72 5 0.55
45 2309K + H 2309X 50 65 11 A 2309X 17 72 50 5 0.30 70 21314E AKE4 + H 314X 52 92 14 A 314X 21 96 70 5 0.65
Remarks The suffix X represents adapter sleeves having narrow slits, for which washers with straight tabs should be used. Remarks The suffix X represents adapter sleeves having narrow slits, for which washers with straight tabs should be used.
B 358 B 359
B356-379E.indd 358-359 11/20/13 5:03:02 PM

B5 B5
B2 B2 A B2 B2 A
B2 B2
B1 B1 B1 b jd B1 B1 B1 b jd
jd 1jd 2 jd 1 jd2 jd 1 jd 2 jd e jK jd 1jd 2 jd 1 jd2 jd 1 jd 2 jd e jK
65 75 1215K + H 215X 43 98 15 A 215X 23 110 80 5 0.70 85 95 1219K + H 219X 55 125 19 A 219X 29 145 101 7 1.35
75 2215K + H 315X 55 98 15 A 315X 23 110 80 12 0.85 95 2219K + H 319X 68 125 19 A 319X 29 145 102 9 1.55
95 1319K + H 319X 68 125 19 A 319X 29 145 102 7 1.55
75 1315K + H 315X 55 98 15 A 315X 23 110 80 5 0.85 95 21319C KE4 + H 319X 68 125 19 A 319X 29 145 102 7 1.55
75 21315E AKE4 + H 315X 55 98 15 A 315X 23 110 80 5 0.85 95 2319K + H 2319X 90 125 19 A 2319X 29 145 105 7 1.9
75 2315K + H 2315X 73 98 15 A 2315X 23 110 82 5 1.05 95 22319E AKE4 + H 2319X 90 125 19 A 2319X 29 145 105 7 1.9
75 22315E AKE4 + H 2315X 73 98 15 A 2315X 23 110 82 5 1.05
90 100 1220K + H 220X 58 130 20 A 220X 30 150 106 7 1.45
70 80 1216K + H 216X 46 105 17 A 216X 25 120 85 5 0.85 100 2220K + H 320X 71 130 20 A 320X 30 150 107 8 1.7
80 2216K + H 316X 59 105 17 A 316X 25 120 86 12 1.05 100 22220E AKE4 + H 320X 71 130 20 A 320X 30 150 107 8 1.7
80 22216E AKE4 + H 316X 59 105 17 A 316X 25 120 86 12 1.05 100 1320K + H 320X 71 130 20 A 320X 30 150 107 7 1.7
100 21320C KE4 + H 320X 71 130 20 A 320X 30 150 107 7 1.7
80 1316K + H 316X 59 105 17 A 316X 25 120 86 5 1.05 100 2320K + H 2320X 97 130 20 A 2320X 30 150 110 7 2.15
80 21316E AKE4 + H 316X 59 105 17 A 316X 25 120 86 5 1.05 100 23220C KE4 + H 2320X 97 130 20 A 2320X 30 150 110 7 2.15
80 2316K + H 2316X 78 105 17 A 2316X 25 120 87 5 1.3 100 22320E AKE4 + H 2320X 97 130 20 A 2320X 30 150 110 7 2.15
80 22316E AKE4 + H 2316X 78 105 17 A 2316X 25 120 87 5 1.3
100 110 23122C KE4 + H 3122X 81 145 21 A 3122X 32 170 117 7 2.25
75 85 1217K + H 217X 50 110 18 A 217X 27 128 90 6 1.0 110 1222K + H 222X 63 145 21 A 222X 32 170 116 7 1.95
85 2217K + H 317X 63 110 18 A 317X 27 128 91 12 1.2 110 2222K + H 322X 77 145 21 A 322X 32 170 117 6 2.3
110 1322K + H 322X 77 145 21 A 322X 32 170 117 9 2.3
85 1317K + H 317X 63 110 18 A 317X 27 128 91 6 1.2 110 2322K + H 2322X 105 145 21 A 2322X 32 170 121 7 2.75
85 21317E AKE4 + H 317X 63 110 18 A 317X 27 128 91 6 1.2
85 2317K + H 2317X 82 110 18 A 2317X 27 128 94 6 1.45 110 23222C KE4 + H 2322X 105 145 21 A 2322X 32 170 121 17 2.75
110 120 23024C DKE4 + H 3024 72 145 22 A 3024 33 180 127 7 1.95
80 90 1218K + H 218X 52 120 18 A 218X 28 139 95 6 1.15 120 23124C KE4 + H 3124 88 155 22 A 3124 33 180 128 7 2.65
90 2218K + H 318X 65 120 18 A 318X 28 139 96 10 1.4 120 22224E AKE4 + H 3124 88 155 22 A 3124 33 180 128 11 2.65
90 22218E AKE4 + H 318X 65 120 18 A 318X 28 139 96 10 1.4 120 23224C KE4 + H 2324 112 155 22 A 2324 33 180 131 17 3.2
120 22324E AKE4 + H 2324 112 155 22 A 2324 33 180 131 7 3.2
90 1318K + H 318X 65 120 18 A 318X 28 139 96 6 1.4
90 21318E AKE4 + H 318X 65 120 18 A 318X 28 139 96 6 1.4 115 130 23026C DKE4 + H 3026 80 155 23 A 3026 34 190 137 8 2.85
90 2318K + H 2318X 86 120 18 A 2318X 28 139 99 6 1.7 130 23126C KE4 + H 3126 92 165 23 A 3126 34 190 138 8 3.65
130 22226E AKE4 + H 3126 92 165 23 A 3126 34 190 138 8 3.65
90 23218C KE4 + H 2318X 86 120 18 A 2318X 28 139 99 6 1.7 130 23226C KE4 + H 2326 121 165 23 A 2326 34 190 142 21 4.6
90 22318E AKE4 + H 2318X 86 120 18 A 2318X 28 139 99 6 1.7 130 22326C KE4 + H 2326 121 165 23 A 2326 34 190 142 8 4.6
Remarks The suffix X represents adapter sleeves having narrow slits, for which washers with straight tabs should be used. Remarks The suffix X represents adapter sleeves having narrow slits, for which washers with straight tabs should be used.
B 360 B 361
B356-379E.indd 360-361 11/20/13 5:03:03 PM

B5 B5
B2 B2 A B2 B2 A
B1 B1 b jd B1 B1 b jd
jd 1 jd 2 jd1 jd 2 jd e jK jd 1 jd 2 jd1 jd 2 jd e jK
125 140 23028C DKE4 + H 3028 82 165 24 A 3028 36 205 147 8 3.15 180 200 23940C AKE4 + H 3940 98 240 32 A 3940 46 260 210 10 8.0
140 23128C KE4 + H 3128 97 180 24 A 3128 36 205 149 8 4.35 200 23040C AKE4 + H 3040 120 240 32 A 3040 46 280 210 10 9.2
140 22228C DKE4 + H 3128 97 180 24 A 3128 36 205 149 8 4.35 200 23140C KE4 + H 3140 150 250 32 A 3140 46 280 212 10 12
140 23228C KE4 + H 2328 131 180 24 A 2328 36 205 152 22 5.55 200 22240C AKE4 + H 3140 150 250 32 A 3140 46 280 212 24 12
140 22328C KE4 + H 2328 131 180 24 A 2328 36 205 152 8 5.55 200 23240C KE4 + H 2340 176 250 32 A 2340 46 280 216 20 14
135 150 23030C DKE4 + H 3030 87 180 26 A 3030 37 220 158 8 3.9 200 22340C AKE4 + H 2340 176 250 32 A 2340 46 280 216 10 14
150 23130C KE4 + H 3130 111 195 26 A 3130 37 220 160 8 5.5
150 22230C DKE4 + H 3130 111 195 26 A 3130 37 220 160 15 5.5 200 220 23944C AKE4 + H 3944 96 260 30 41 A 3944 55 280 231 10 8.32
150 23230C KE4 + H 2330 139 195 26 A 2330 37 220 163 20 6.6 220 23044C AKE4 + H 3044 128 260 30 41 A 3044 55 320 231 12 10.5
150 22330C AKE4 + H 2330 139 195 26 A 2330 37 220 163 8 6.6 220 23144C KE4 + H 3144 158 280 32 44 A 3144 55 320 233 10 14.5
140 160 23932C AKE4 + H 3932 78 190 28 A 3932 39 205 168 8 4.64 220 22244C AKE4 + H 3144 158 280 32 44 A 3144 55 320 233 22 14.5
160 23032C DKE4 + H 3032 93 190 28 A 3032 39 230 168 8 5.2 220 23244C KE4 + H 2344 183 280 32 44 A 2344 55 320 236 11 16.5
160 23132C KE4 + H 3132 119 210 28 A 3132 39 230 170 8 7.65 220 22344C AKE4 + H 2344 183 280 32 44 A 2344 55 320 236 10 16.5
160 22232C DKE4 + H 3132 119 210 28 A 3132 39 230 170 14 7.65
160 23232C KE4 + H 2332 147 210 28 A 2332 39 230 174 18 9.15 220 240 23948C AKE4 + H 3948 101 290 34 46 A 3948 60 300 251 11 11.2
160 22332C AKE4 + H 2332 147 210 28 A 2332 39 230 174 8 9.15 240 23048C AKE4 + H 3048 133 290 34 46 A 3048 60 340 251 11 13
240 23148C KE4 + H 3148 169 300 34 46 A 3148 60 340 254 11 17.5
150 170 23934B CAKE4 + H 3934 79 200 29 A 3934 40 215 179 8 5.07
170 23034C DKE4 + H 3034 101 200 29 A 3034 40 250 179 8 6.0 240 22248C AKE4 + H 3148 169 300 34 46 A 3148 60 340 254 19 17.5
170 23134C KE4 + H 3134 122 220 29 A 3134 40 250 180 8 8.4 240 23248C AKE4 + H 2348 196 300 34 46 A 2348 60 340 257 6 19.5
170 22234C DKE4 + H 3134 122 220 29 A 3134 40 250 180 10 8.4 240 22348C AKE4 + H 2348 196 300 34 46 A 2348 60 340 257 11 19.5
170 23234C KE4 + H 2334 154 220 29 A 2334 40 250 185 18 10
170 22334C AKE4 + H 2334 154 220 29 A 2334 40 250 185 8 10 240 260 23952C AKE4 + H 3952 116 310 34 46 A 3952 60 330 272 11 13.4
260 23052C AKE4 + H 3052 147 310 34 46 A 3052 60 370 272 13 15.5
160 180 23936C AKE4 + H 3936 87 210 30 A 3936 41 230 189 8 5.87 260 23152C AKE4 + H 3152 187 330 36 49 A 3152 60 370 276 11 22
180 23036C DKE4 + H 3036 109 210 30 A 3036 41 260 189 8 6.85
180 23136C KE4 + H 3136 131 230 30 A 3136 41 260 191 8 9.5 260 22252C AKE4 + H 3152 187 330 36 49 A 3152 60 370 276 25 22
180 22236C DKE4 + H 3136 131 230 30 A 3136 41 260 191 18 9.5 260 23252C AKE4 + H 2352 208 330 36 49 A 2352 60 370 278 2 24
180 23236C KE4 + H 2336 161 230 30 A 2336 41 260 195 22 11.5 260 22352C AKE4 + H 2352 208 330 36 49 A 2352 60 370 278 11 24
180 22336C AKE4 + H 2336 161 230 30 A 2336 41 260 195 8 11.5
170 190 23938C AKE4 + H 3938 89 220 31 A 3938 43 240 199 9 6.35 260 280 23956C AKE4 + H 3956 121 330 38 50 A 3956 65 350 292 12 15.5
190 23038C AKE4 + H 3038 112 220 31 A 3038 43 270 199 9 7.45 280 23056C AKE4 + H 3056 152 330 38 50 A 3056 65 390 292 12 17.5
190 23138C KE4 + H 3138 141 240 31 A 3138 43 270 202 9 11 280 23156C AKE4 + H 3156 192 350 38 51 A 3156 65 390 296 12 24.5
190 22238C AKE4 + H 3138 141 240 31 A 3138 43 270 202 21 11 280 22256C AKE4 + H 3156 192 350 38 51 A 3156 65 390 296 28 24.5
190 23238C KE4 + H 2338 169 240 31 A 2338 43 270 206 21 12.5 280 23256C AKE4 + H 2356 221 350 38 51 A 2356 65 390 299 11 28
190 22338C AKE4 + H 2338 169 240 31 A 2338 43 270 206 9 12.5 280 22356C AKE4 + H 2356 221 350 38 51 A 2356 65 390 299 12 28
B 362 B 363
B356-379E.indd 362-363 11/20/13 5:03:04 PM

B5 B5
B2 B2 A B2 B2 A
B1 B1 b jd B1 B1 b jd
jd 1 jd 2 jd1 jd 2 jd e jK jd 1 jd 2 jd1 jd 2 jd e jK
280 300 23960C AKE4 + H 3960 140 360 42 54 A 3960 69 380 313 12 20.7 430 460 23992C AKE4 + H 3992 189 540 60 77 A 3992 99 570 478 17 62
300 23060C AKE4 + H 3060 168 360 42 54 A 3060 69 430 313 12 23 460 23092C AKE4 + H 3092 234 540 60 77 A 3092 99 650 478 17 69.5
300 23160C AKE4 + H 3160 208 380 40 53 A 3160 69 430 317 12 30 460 23192C AKE4 + H 3192 326 580 75 95 A 3192 99 650 485 17 116
460 23292C AKE4 + H 3292 382 580 75 95 A 3292 99 650 491 17 132
300 22260C AKE4 + H 3160 208 380 40 53 A 3160 69 430 317 32 30
300 23260C AKE4 + H 3260 240 380 40 53 A 3260 69 430 321 12 34 450 480 23996C AKE4 + H 3996 200 560 60 77 A 3996 99 600 499 18 67.5
300 320 23964C AKE4 + H 3964 140 380 42 55 A 3964 72 400 334 13 21.8 480 23096C AKE4 + H 3096 237 560 60 77 A 3096 99 690 499 18 73.5
320 23064C AKE4 + H 3064 171 380 42 55 A 3064 72 450 334 13 24.5 480 23196C AKE4 + H 3196 335 620 75 95 A 3196 99 690 505 18 133
320 23164C AKE4 + H 3164 226 400 42 56 A 3164 72 450 339 13 35 480 23296C AKE4 + H 3296 397 620 75 95 A 3296 99 690 512 18 152
320 22264C AKE4 + H 3164 226 400 42 56 A 3164 72 450 339 39 35 470 500 239/500C AKE4 + H 39/500 208 580 68 85 A 39/500 109 620 519 18 74.6
320 23264C AKE4 + H 3264 258 400 42 56 A 3264 72 450 343 13 39.5 500 230/500C AKE4 + H 30/500 247 580 68 85 A 30/500 109 700 519 18 82
500 231/500C AKE4 + H 31/500 356 630 80 100 A 31/500 109 700 527 18 143
320 340 23968C AKE4 + H 3968 144 400 45 58 A 3968 75 430 354 14 24.6 500 232/500C AKE4 + H 32/500 428 630 80 100 A 32/500 109 700 534 18 166
340 23068C AKE4 + H 3068 187 400 45 58 A 3068 75 490 355 14 28.5
340 23168C AKE4 + H 3168 254 440 55 72 A 3168 75 490 360 14 49.5
340 23268C AKE4 + H 3268 288 440 55 72 A 3268 75 490 364 14 54.5
340 360 23972C AKE4 + H 3972 144 420 45 58 A 3972 75 450 374 14 25.7
360 23072C AKE4 + H 3072 188 420 45 58 A 3072 75 510 375 14 30.5
360 23172C AKE4 + H 3172 259 460 58 75 A 3172 75 510 380 14 54
360 23272C AKE4 + H 3272 299 460 58 75 A 3272 75 510 385 14 60.5
360 380 23976C AKE4 + H 3976 164 450 48 62 A 3976 82 480 396 15 31.9
380 23076C AKE4 + H 3076 193 450 48 62 A 3076 82 540 396 15 36
380 23176C AKE4 + H 3176 264 490 60 77 A 3176 82 540 401 15 61.5
380 23276C AKE4 + H 3276 310 490 60 77 A 3276 82 540 405 15 69.5
380 400 23980C AKE4 + H 3980 168 470 52 66 A 3980 86 500 417 15 35.2
400 23080C AKE4 + H 3080 210 470 52 66 A 3080 86 580 417 15 41.5
400 23180C AKE4 + H 3180 272 520 62 82 A 3180 86 580 421 15 70.5
400 23280C AKE4 + H 3280 328 520 62 82 A 3280 86 580 427 15 81
400 420 23984C AKE4 + H 3984 168 490 52 66 A 3984 86 520 437 16 36.6
420 23084C AKE4 + H 3084 212 490 52 66 A 3084 86 600 437 16 43.5
420 23184C AKE4 + H 3184 304 540 70 90 A 3184 86 600 443 16 84
420 23284C AKE4 + H 3284 352 540 70 90 A 3284 86 600 448 16 94
410 440 23988C AKE4 + H 3988 189 520 60 77 A 3988 99 550 458 17 58.6
440 23088C AKE4 + H 3088 228 520 60 77 A 3088 99 620 458 17 65
440 23188C AKE4 + H 3188 307 560 70 90 A 3188 99 620 464 17 104
440 23288C AKE4 + H 3288 361 560 70 90 A 3288 99 620 469 17 118
B 364 B 365
B356-379E.indd 364-365 11/20/13 5:03:05 PM

WITHDRAWAL SLEEVES FOR ROLLING BEARINGS
G1 G1
B3 B3
B4 jd 1 B4 jd 1
G G
Nominal Screw Thread Dimensions Mass Nominal Screw Thread Dimensions Mass
Shaft Bearing (mm) (kg) Shaft Bearing (mm) (kg)
Diameter Bore Dia. Nominal Numbers Diameter Bore Dia. Nominal Numbers
(mm) (mm) G B3 G1 B4 (mm) (mm) G B3 G1 B4
d1 d Applicable Bearings approx. d1 d Applicable Bearings approx.
35 40 21308E AKE4 + AH 308 M 45 1.5 29 6 32 0.09 90 95 22219E AKE4 + AHX 319 M 105 2 57 10 61 0.595
40 22308E AKE4 + AH 2308 M 45 1.5 40 7 43 0.13 95 21319C KE4 + AHX 319 M 105 2 57 10 61 0.595
40 45 21309E AKE4 + AH 309 M 50 1.5 31 6 34 0.11 95 22319E AKE4 + AHX 2319 M 105 2 85 16 89 0.89
45 22309E AKE4 + AH 2309 M 50 1.5 44 7 47 0.165
95 100 21320C KE4 + AHX 3120 M 110 2 64 11 68 0.70
45 50 21310E AKE4 + AHX 310 M 55 2 35 7 38 0.16 100 22220E AKE4 + AHX 320 M 110 2 59 10 63 0.66
50 22310E AKE4 + AHX 2310 M 55 2 50 9 53 0.235 100 21320C KE4 + AHX 320 M 110 2 59 10 63 0.66
100 23220C KE4 + AHX 3220 M 110 2 73 11 77 0.77
50 55 22211E AKE4 + AHX 311 M 60 2 37 7 40 0.19 100 22320E AKE4 + AHX 2320 M 110 2 90 16 94 1.0
55 21311E AKE4 + AHX 311 M 60 2 37 7 40 0.19 105 110 23122C KE4 + AHX 3122 M 120 2 68 11 72 0.76
55 22311E AKE4 + AHX 2311 M 60 2 54 10 57 0.285 110 22222E AKE4 + AHX 3122 M 120 2 68 11 72 0.76
110 24122C K30E4 + AH 24122 M 115 2 82 13 91 0.73
55 60 22212E AKE4 + AHX 312 M 65 2 40 8 43 0.215
60 65 22213E AKE4 + AH 313 M 75 2 42 8 45 0.255 115 120 23024C DKE4 + AHX 3024 M 130 2 60 13 64 0.75
65 21313E AKE4 + AH 313 M 75 2 42 8 45 0.255 120 24024C K30E4 + AH 24024 M 125 2 73 13 82 0.70
65 22313E AKE4 + AH 2313 M 75 2 61 12 64 0.395 120 23124C KE4 + AHX 3124 M 130 2 75 12 79 0.95
120 22224E AKE4 + AHX 3124 M 130 2 75 12 79 0.95
65 70 22214E AKE4 + AH 314 M 80 2 43 8 47 0.28 120 24124C K30E4 + AH 24124 M 130 2 93 13 102 1.02
70 21314E AKE4 + AH 314 M 80 2 43 8 47 0.28 120 23224C KE4 + AHX 3224 M 135 2 90 13 94 1.3
70 75 22215E AKE4 + AH 315 M 85 2 45 8 49 0.315 125 130 23026C DKE4 + AHX 3026 M 140 2 67 14 71 0.95
75 21315E AKE4 + AH 315 M 85 2 45 8 49 0.315 130 24026C K30E4 + AH 24026 M 135 2 83 14 93 0.89
75 80 22216E AKE4 + AH 316 M 90 2 48 8 52 0.365 130 22226E AKE4 + AHX 3126 M 140 2 78 12 82 1.08
80 21316E AKE4 + AH 316 M 90 2 48 8 52 0.365 130 24126C K30E4 + AH 24126 M 140 2 94 14 104 1.14
130 22326C KE4 + AHX 2326 M 145 2 115 19 119 1.97
80 85 22217E AKE4 + AHX 317 M 95 2 52 9 56 0.48 135 140 23028C DKE4 + AHX 3028 M 150 2 68 14 73 1.01
85 21317E AKE4 + AHX 317 M 95 2 52 9 56 0.48 140 24028C K30E4 + AH 24028 M 145 2 83 14 93 0.96
85 90 22218E AKE4 + AHX 318 M 100 2 53 9 57 0.52 140 22228C DKE4 + AHX 3128 M 150 2 83 14 88 1.28
90 21318E AKE4 + AHX 318 M 100 2 53 9 57 0.52 140 24128C K30E4 + AH 24128 M 150 2 99 14 109 1.3
90 23218C KE4 + AHX 3218 M 100 2 63 10 67 0.58 140 23228C KE4 + AHX 3228 M 155 3 104 15 109 1.84
B 366 B 367
B356-379E.indd 366-367 11/20/13 5:03:06 PM

G1 G1
B3 B3
B4 jd 1 B4 jd 1
G G
145 150 23030C DKE4 + AHX 3030 M 160 3 72 15 77 1.15 190 200 23040C AKE4 + AH 3040 Tr 215 4 102 19 108 3.8
150 24030C K30E4 + AH 24030 M 155 3 90 15 101 1.11 200 24040C K30E4 + AH 24040 Tr 210 4 127 18 140 3.92
150 23130C KE4 + AHX 3130 M 165 3 96 15 101 1.79 200 23140C KE4 + AH 3140 Tr 220 4 134 21 140 5.5
150 22230C DKE4 + AHX 3130 M 165 3 96 15 101 1.79 200 24140C K30E4 + AH 24140 Tr 210 4 158 18 171 5.0
150 24130C K30E4 + AH 24130 M 160 3 115 15 126 1.63 200 22240C AKE4 + AH 2240 Tr 220 4 118 19 123 4.7
150 23230C KE4 + AHX 3230 M 165 3 114 17 119 2.22 200 23240C KE4 + AH 3240 Tr 220 4 153 25 160 6.7
150 22330C AKE4 + AHX 2330 M 165 3 135 24 140 2.82 200 22340C AKE4 + AH 2340 Tr 220 4 170 30 177 7.55
150 160 23032C DKE4 + AH 3032 M 170 3 77 16 82 2.05 200 220 23044C AKE4 + AH 3044 Tr 235 4 111 20 117 7.4
160 24032C K30E4 + AH 24032 M 170 3 95 15 106 2.28 220 24044C K30E4 + AH 24044 Tr 230 4 138 20 152 8.23
160 23132C KE4 + AH 3132 M 180 3 103 16 108 3.2 220 23144C KE4 + AH 3144 Tr 240 4 145 23 151 10.5
160 22232C DKE4 + AH 3132 M 180 3 103 16 108 3.2 220 24144C K30E4 + AH 24144 Tr 230 4 170 20 184 10.3
160 24132C K30E4 + AH 24132 M 170 3 124 15 135 3.03 220 22244C AKE4 + AH 2244 Tr 240 4 130 20 136 9.1
160 23232C KE4 + AH 3232 M 180 3 124 20 130 4.1 220 23244C KE4 + AH 2344 Tr 240 4 181 30 189 13.5
160 22332C AKE4 + AH 2332 M 180 3 140 24 146 4.7 220 22344C AKE4 + AH 2344 Tr 240 4 181 30 189 13.5
170 24034C K30E4 + AH 24034 M 180 3 106 16 117 2.74 240 24048C K30E4 + AH 24048 Tr 250 4 138 20 153 9.0
170 23134C KE4 + AH 3134 M 190 3 104 16 109 3.4 240 23148C KE4 + AH 3148 Tr 260 4 154 25 161 12
170 22234C DKE4 + AH 3134 M 190 3 104 16 109 3.4 240 24148C K30E4 + AH 24148 Tr 260 4 180 20 195 12.6
170 24134C K30E4 + AH 24134 M 180 3 125 16 136 3.26 240 22248C AKE4 + AH 2248 Tr 260 4 144 21 150 11
170 23234C KE4 + AH 3234 M 190 3 134 24 140 4.8 240 23248C AKE4 + AH 2348 Tr 260 4 189 30 197 15.5
180 24036C K30E4 + AH 24036 M 190 3 116 16 127 3.19 260 24052C AK30E4 + AH 24052 Tr 270 4 162 22 178 11.7
180 23136C KE4 + AH 3136 M 200 3 116 19 122 4.2 260 23152C AKE4 + AH 3152 Tr 290 4 172 26 179 16
180 24136C K30E4 + AH 24136 M 190 3 134 16 145 3.74 260 24152C AK30E4 + AH 24152 Tr 280 4 202 22 218 15.5
180 22236C DKE4 + AH 2236 M 200 3 105 17 110 3.75 260 22252C AKE4 + AH 2252 Tr 290 4 155 23 161 14
180 23236C KE4 + AH 3236 M 200 3 140 24 146 5.3 260 23252C AKE4 + AH 2352 Tr 290 4 205 30 213 19.5
180 190 23038C AKE4 + AH 3038 Tr 205 4 96 18 102 3.35 260 280 23056C AKE4 + AH 3056 Tr 300 4 131 24 139 12
190 24038C K30E4 + AH 24038 M 200 3 118 18 131 3.47 280 24056C AK30E4 + AH 24056 Tr 290 4 162 22 179 12.6
190 23138C KE4 + AH 3138 Tr 210 4 125 20 131 4.9 280 23156C AKE4 + AH 3156 Tr 310 5 175 28 183 17.5
190 24138C K30E4 + AH 24138 M 200 3 146 18 159 4.38 280 24156C AK30E4 + AH 24156 Tr 300 4 202 22 219 16.8
190 22238C AKE4 + AH 2238 Tr 210 4 112 18 117 4.25 280 22256C AKE4 + AH 2256 Tr 310 5 155 24 163 15
190 23238C KE4 + AH 3238 Tr 210 4 145 25 152 5.9 280 23256C AKE4 + AH 2356 Tr 310 5 212 30 220 21.5
190 22338C AKE4 + AH 2338 Tr 210 4 160 26 167 6.65 280 22356C AKE4 + AH 2356 Tr 310 5 212 30 220 21.5
B 368 B 369
B356-379E.indd 368-369 11/20/13 5:03:07 PM

G1 G1
B3 B3
B4 jd 1 B4 jd 1
G G
280 300 23060C AKE4 + AH 3060 Tr 320 5 145 26 153 14.5 400 420 23084C AKE4 + AH 3084 Tr 450 5 186 34 196 29
300 24060C AK30E4 + AH 24060 Tr 310 5 184 24 202 15.5 420 24084C AK30E4 + AH 24084 Tr 440 5 230 30 252 29.8
300 23160C AKE4 + AH 3160 Tr 330 5 192 30 200 21 420 23184C AKE4 + AH 3184 Tr 460 5 266 40 276 46.5
300 24160C AK30E4 + AH 24160 Tr 320 5 224 24 242 20.3 420 24184C AK30E4 + AH 24184 Tr 440 5 310 30 332 41.4
300 22260C AKE4 + AH 2260 Tr 330 5 170 26 178 18 420 23284C AKE4 + AH 3284 Tr 460 5 321 46 331 59
300 23260C AKE4 + AH 3260 Tr 330 5 228 34 236 20
420 440 23088C AKE4 + AHX 3088 Tr 470 5 194 35 205 42
300 320 23064C AKE4 + AH 3064 Tr 345 5 149 27 157 16 440 24088C AK30E4 + AH 24088 Tr 460 5 242 30 264 33
320 24064C AK30E4 + AH 24064 Tr 330 5 184 24 202 16.4 440 23188C AKE4 + AHX 3188 Tr 480 5 270 42 281 50
320 23164C AKE4 + AH 3164 Tr 350 5 209 31 217 24.5
440 24188C AK30E4 + AH 24188 Tr 460 5 310 30 332 43.5
320 23264C AKE4 + AH 3264 Tr 350 5 246 36 254 25
440 460 23092C AKE4 + AHX 3092 Tr 490 5 202 37 213 46
320 340 23068C AKE4 + AH 3068 Tr 365 5 162 28 171 19.5 460 24092C AK30E4 + AH 24092 Tr 480 5 250 32 273 35.9
340 23168C AKE4 + AH 3168 Tr 370 5 225 33 234 29
460 24192C AK30E4 + AH 24192 Tr 480 5 332 32 355 49.7
340 24168C AK30E4 + AH 24168 Tr 360 5 269 26 288 28.3 460 23292C AKE4 + AHX 3292 Tr 510 6 349 50 360 74.5
340 23268C AKE4 + AH 3268 Tr 370 5 264 38 273 35.5
460 480 23096C AKE4 + AHX 3096 Tr 520 6 205 38 217 51
340 360 23072C AKE4 + AH 3072 Tr 385 5 167 30 176 21 480 24096C AK30E4 + AH 24096 Tr 500 5 250 32 273 37.5
360 23172C AKE4 + AH 3172 Tr 400 5 229 35 238 33
480 24196C AK30E4 + AH 24196 Tr 500 5 340 32 363 53
360 24172C AK30E4 + AH 24172 Tr 380 5 269 26 289 30 480 23296C AKE4 + AHX 3296 Tr 530 6 364 52 376 82
360 23272C AKE4 + AH 3272 Tr 400 5 274 40 283 41.5
480 500 230/500C AKE4 + AHX 30/500 Tr 540 6 209 40 221 54.5
360 380 23076C AKE4 + AH 3076 Tr 410 5 170 31 180 23.5 500 240/500C AK30E4 + AH 240/500 Tr 530 6 253 35 276 41.9
380 24076C AK30E4 + AH 24076 Tr 400 5 208 28 228 24.1 500 231/500C AKE4 + AHX 31/500 Tr 550 6 313 47 325 71
380 23176C AKE4 + AH 3176 Tr 420 5 232 36 242 35.5
380 24176C AK30E4 + AH 24176 Tr 400 5 271 28 291 32.1 500 241/500C AK30E4 + AH 241/500 Tr 530 6 360 35 383 61.2
380 23276C AKE4 + AH 3276 Tr 420 5 284 42 294 45.5 500 232/500C AKE4 + AHX 32/500 Tr 550 6 393 54 405 94.5
380 400 23080C AKE4 + AH 3080 Tr 430 5 183 33 193 27.5

400 24080C AK30E4 + AH 24080 Tr 420 5 228 28 248 28
400 23180C AKE4 + AH 3180 Tr 440 5 240 38 250 39.5
400 24180C AK30E4 + AH 24180 Tr 420 5 278 28 298 34.8
400 23280C AKE4 + AH 3280 Tr 440 5 302 44 312 51.5
B 370 B 371
B356-379E.indd 370-371 11/20/13 5:03:07 PM

NUTS FOR ROLLING BEARINGS
(For Adapters and Shafts)
g B g B
b 30 G b 30 G
h h
r r
g jd3 jd 1 g jd3 jd 1
d2 d2
Nut with Washer Nut with Washer

Nut Series AN Reference Nut Series AN Reference
Nominal Screw Threads Basic Dimensions Mass Adapter (1) Nominal Screw Threads Basic Dimensions Mass Adapter (1)
Numbers Washer Shaft Numbers Washer Shaft
d2 d1 g b h d3 B r (kg) Sleeve Bore
Numbers Dia. d2 d1 g b h d3 B r (kg) Sleeve Bore
Numbers Dia.
G max. approx. Dia. Numbers G max. approx. Dia. Numbers
AN 02 M 151 25 21 21 4 2 15.5 5 0.4 0.010 AW 02 X 15 AN 26 M 1302 165 149 155 12 5 131 21 0.7 1.25 26 AW 26 130
AN 03 M 171 28 24 24 4 2 17.5 5 0.4 0.013 AW 03 X 17 AN 27 M 1352 175 160 163 14 6 136 22 0.7 1.55 AW 27 135
AN 04 M 201 32 26 28 4 2 20.5 6 0.4 0.019 04 AW 04 X 20 AN 28 M 1402 180 160 168 14 6 141 22 0.7 1.56 28 AW 28 140
AN 05 M 251.5 38 32 34 5 2 25.8 7 0.4 0.025 05 AW 05 X 25 AN 29 M 1452 190 172 178 14 6 146 24 0.7 2.0 AW 29 145
AN 06 M 301.5 45 38 41 5 2 30.8 7 0.4 0.043 06 AW 06 X 30 AN 30 M 1502 195 171 183 14 6 151 24 0.7 2.03 30 AW 30 150
AN 07 M 351.5 52 44 48 5 2 35.8 8 0.4 0.053 07 AW 07 X 35 AN 31 M 1553 200 182 186 16 7 156.5 25 0.7 2.21
AN 08 M 401.5 58 50 53 6 2.5 40.8 9 0.5 0.085 08 AW 08 X 40 AN 32 M 1603 210 182 196 16 7 161.5 25 0.7 2.59 32 AW 32 160
AN 09 M 451.5 65 56 60 6 2.5 45.8 10 0.5 0.119 09 AW 09 X 45 AN 33 M 1653 210 193 196 16 7 166.5 26 0.7 2.43
AN 10 M 501.5 70 61 65 6 2.5 50.8 11 0.5 0.148 10 AW 10 X 50 AN 34 M 1703 220 193 206 16 7 171.5 26 0.7 2.8 34 AW 34 170
AN 11 M 552 75 67 69 7 3 56 11 0.5 0.158 11 AW 11 X 55 AN 36 M 1803 230 203 214 18 8 181.5 27 0.7 3.05 36 AW 36 180
AN 12 M 602 80 73 74 7 3 61 11 0.5 0.174 12 AW 12 X 60 AN 38 M 1903 240 214 224 18 8 191.5 28 0.7 3.4 38 AW 38 190
AN 13 M 652 85 79 79 7 3 66 12 0.5 0.203 13 AW 13 X 65 AN 40 M 2003 250 226 234 18 8 201.5 29 0.7 3.7 40 AW 40 200
Nut Series ANL

AN 14 M 702 92 85 85 8 3.5 71 12 0.5 0.242 14 AW 14 X 70
AN 15 M 752 98 90 91 8 3.5 76 13 0.5 0.287 15 AW 15 X 75 ANL 24 M 1202 145 133 135 12 5 121 20 0.7 0.78 24 AWL 24 120
AN 16 M 802 105 95 98 8 3.5 81 15 0.6 0.395 16 AW 16 X 80 ANL 26 M 1302 155 143 145 12 5 131 21 0.7 0.88 26 AWL 26 130
ANL 28 M 1402 165 151 153 14 6 141 22 0.7 0.99 28 AWL 28 140
AN 17 M 852 110 102 103 8 3.5 86 16 0.6 0.45 17 AW 17 X 85
AN 18 M 902 120 108 112 10 4 91 16 0.6 0.555 18 AW 18 X 90 ANL 30 M 1502 180 164 168 14 6 151 24 0.7 1.38 30 AWL 30 150
AN 19 M 952 125 113 117 10 4 96 17 0.6 0.66 19 AW 19 X 95 ANL 32 M 1603 190 174 176 16 7 161.5 25 0.7 1.56 32 AWL 32 160
ANL 34 M 1703 200 184 186 16 7 171.5 26 0.7 1.72 34 AWL 34 170
AN 20 M 1002 130 120 122 10 4 101 18 0.6 0.70 20 AW 20 X 100
AN 21 M 1052 140 126 130 12 5 106 18 0.7 0.845 21 AW 21 X 105 ANL 36 M 1803 210 192 194 18 8 181.5 27 0.7 1.95 36 AWL 36 180
AN 22 M 1102 145 133 135 12 5 111 19 0.7 0.965 22 AW 22 X 110 ANL 38 M 1903 220 202 204 18 8 191.5 28 0.7 2.08 38 AWL 38 190
ANL 40 M 2003 240 218 224 18 8 201.5 29 0.7 2.98 40 AWL 40 200
AN 23 M 1152 150 137 140 12 5 116 19 0.7 1.01 AW 23 . 115 Note (1) Series AN is applicable to adapter sleeve Series A31 and A23.
AN 24 M 1202 155 138 145 12 5 121 20 0.7 1.08 24 AW 24 . 120 Series ANL is applicable to adapter sleeve Series A30.
AN 25 M 1252 160 148 150 12 5 126 21 0.7 1.19 AW 25 . 125
Remarks The basic design and dimensions of screw threads are in accordance with JIS B 0205.
Note (1) Applicable to adapter sleeve Series A31, A2, A3, and A23.
Remarks The basic design and dimensions of screw threads are in accordance with JIS B 0205.
B 372 B 373
B356-379E.indd 372-373 11/20/13 5:03:08 PM

NUTS FOR ROLLING BEARINGS
(For Adapters and Shafts) (For Withdrawal Sleeves)
g B g B
Tapped
b h Holes l 30 G b 30 G
r s h
r
jd 3
jd 4 jd 1 g g jd3 jd 1
d2
d2
Nut with Stopper

Nut Series AN Reference Nut Series HN Reference
Nominal Screw Basic Dimensions Mass Adapter (1) Nominal Screw Basic Dimensions Mass Withdrawal Sleeve Numbers
Numbers Stopper Shaft Numbers
Threads
d2 d1 g b h d3 r
B max. Tapped Holes (kg) Sleeve Bore
Numbers Dia.
Threads
d2 d1 g b h d3 r (kg)
B max.
G l Screw Threads (S) d4 approx. Dia. Numbers G approx. AH 31 AH 22 AH 32 AH 23
AN 44 Tr 2204 280 250 260 20 10 222 32 0.8 15 M 81.25 238 5.2 44 AL 44 220 HN 42 Tr 2104 270 238 250 20 10 212 30 0.8 4.75 AH 3138 AH 2238 AH 3238 AH 2338
AN 48 Tr 2404 300 270 280 20 10 242 34 0.8 15 M 81.25 258 5.95 48 AL 44 240 HN 44 Tr 2204 280 250 260 20 10 222 32 0.8 5.35 AH 3140 AH 2240 AH 3240 AH 2340
AN 52 Tr 2604 330 300 306 24 12 262 36 0.8 18 M 101.5 281 8.05 52 AL 52 260 HN 48 Tr 2404 300 270 280 20 10 242 34 0.8 6.2 AH 3144 AH 2244 AH 2344
HN 52 Tr 2604 330 300 306 24 12 262 36 0.8 8.55 AH 3148 AH 2248 AH 2348
AN 56 Tr 2804 350 320 326 24 12 282 38 0.8 18 M 101.5 301 9.05 56 AL 52 280 HN 58 Tr 2904 370 330 346 24 12 292 40 0.8 11.8 AH 3152 AH 2252 AH 2352
AN 60 Tr 3004 380 340 356 24 12 302 40 0.8 18 M 101.5 326 11.8 60 AL 60 300 HN 62 Tr 3105 390 350 366 24 12 312.5 42 0.8 13.4 AH 3156 AH 2256 AH 2356
AN 64 Tr 3205 400 360 376 24 12 322.5 42 0.8 18 M 101.5 345 13.1 64 AL 64 320
HN 66 Tr 3305 420 380 390 28 15 332.5 52 1 20.4 AH 3160 AH 2260 AH 3260
AN 68 Tr 3405 440 400 410 28 15 342.5 55 1 21 M 121.75 372 23.1 68 AL 68 340 HN 70 Tr 3505 450 410 420 28 15 352.5 55 1 25.2 AH 3164 AH 2264 AH 3264
AN 72 Tr 3605 460 420 430 28 15 362.5 58 1 21 M 121.75 392 25.1 72 AL 68 360 HN 74 Tr 3705 470 430 440 28 15 372.5 58 1 28.2 AH 3168 AH 3268
AN 76 Tr 3805 490 450 454 32 18 382.5 60 1 21 M 121.75 414 31 76 AL 76 380 HN 80 Tr 4005 520 470 484 32 18 402.5 62 1 40 AH 3172 AH 3272
HN 84 Tr 4205 540 490 504 32 18 422.5 70 1 46.9 AH 3176 AH 3276
AN 80 Tr 4005 520 470 484 32 18 402.5 62 1 27 M 162 439 37 80 AL 80 400 HN 88 Tr 4405 560 510 520 36 20 442.5 70 1 48.5 AH 3180 AH 3280
AN 84 Tr 4205 540 490 504 32 18 422.5 70 1 27 M 162 459 43.5 84 AL 80 420
AN 88 Tr 4405 560 510 520 36 20 442.5 70 1 27 M 162 477 45 88 AL 88 440 HN 92 Tr 4605 580 540 540 36 20 462.5 75 1 55 AH 3184 AH 3284
HN 96 Tr 4805 620 560 580 36 20 482.5 75 1 67 AHX 3188 AHX 3288
AN 92 Tr 4605 580 540 540 36 20 462.5 75 1 27 M 162 497 50.5 92 AL 88 460 HN 102 Tr 5106 650 590 604 40 23 513 80 1 75 AHX 3192 AHX 3292
AN 96 Tr 4805 620 560 580 36 20 482.5 75 1 27 M 162 527 62 96 AL 96 480 HN 106 Tr 5306 670 610 624 40 23 533 80 1 78 AHX 3196 AHX 3296
AN 100 Tr 5005 630 580 584 40 23 502.5 80 1 27 M 162 539 63.5 /500 AL 100 500 HN 110 Tr 5506 700 640 654 40 23 553 80 1 92.5 AHX 31/500 AHX 32/500
Nut Series ANL Nut Series HNL AH 30 AH 2

ANL 44 Tr 2204 260 242 242 20 9 222 30 0.8 12 M 61 229 3.1 44 ALL 44 220 HNL 41 Tr 2054 250 232 234 18 8 207 30 0.8 3.45 AH 3038 AH 238
ANL 48 Tr 2404 290 270 270 20 10 242 34 0.8 15 M 81.25 253 5.15 48 ALL 48 240 HNL 43 Tr 2154 260 242 242 20 9 217 30 0.8 3.7 AH 3040 AH 240
ANL 56 Tr 2804 330 310 310 24 10 282 38 0.8 15 M 81.25 293 6.8 56 ALL 56 280
HNL 52 Tr 2604 310 290 290 20 10 262 34 0.8 5.8 AH 3048 AH 248
ANL 64 Tr 3205 380 356 356 24 12 322.5 42 0.8 15 M 81.25 335 9.95 64 ALL 64 320 HNL 60 Tr 3004 360 336 336 24 12 302 42 0.8 9.6 AH 3056 AH 256
ANL 68 Tr 3405 400 376 376 24 12 342.5 45 1 15 M 81.25 355 11.7 68 ALL 64 340 HNL 64 Tr 3205 380 356 356 24 12 322.5 42 1 10.3 AH 3060
ANL 72 Tr 3605 420 394 394 28 13 362.5 45 1 15 M 81.25 374 12 72 ALL 72 360 HNL 69 Tr 3455 410 384 384 28 13 347.5 45 1 11.5 AH 3064
ANL 80 Tr 4005 470 442 442 28 14 402.5 52 1 18 M 101.5 418 16.9 80 ALL 76 400 HNL 77 Tr 3855 450 422 422 28 14 387.5 48 1 15 AH 3072
HNL 82 Tr 4105 480 452 452 32 14 412.5 52 1 19 AH 3076
ANL 88 Tr 4405 520 490 490 32 15 442.5 60 1 21 M 121.75 462 26.2 88 ALL 88 440
ANL 92 Tr 4605 540 510 510 32 15 462.5 60 1 21 M 121.75 482 28 92 ALL 88 460 HNL 90 Tr 4505 520 490 490 32 15 452.5 60 1 23.8 AH 3084
HNL 94 Tr 4705 540 510 510 32 15 472.5 60 1 25 AHX 3088
ANL 96 Tr 4805 560 530 530 36 15 482.5 60 1 21 M 121.75 502 29.5 96 ALL 96 480 HNL 98 Tr 4905 580 550 550 36 15 492.5 60 1 34 AHX 3092
ANL 100 Tr 5005 580 550 550 36 15 502.5 68 1 21 M 121.75 522 33.5 /500 ALL 96 500
HNL 104 Tr 5206 600 570 570 36 15 523 68 1 37 AHX 3096
Note (1) Series AN is applicable to adapter sleeve Series A31, A32 and A23. Series ANL is applicable to adapter sleeve Series HNL 108 Tr 5406 630 590 590 40 20 543 68 1 43.5 AHX 30/500
A30.
Remarks 1. The basic design and dimensions of screw threads are in accordance with JIS B 0216. Remarks 1. The basic design and dimensions of screw threads are in accordance with JIS B 0216.
2. The basic design and dimensions of threads in tapped holes are in accordance with JIS B 0205. 2. The number of notches in the nut may be bigger than that shown in the above figure.
B 374 B 375
B356-379E.indd 374-375 11/20/13 5:03:09 PM

NUTS FOR ROLLING BEARINGS STOPPERS FOR NUTS
(Combination of Withdrawal Sleeves and Nuts)
t1
t1
js 1 i L3
L2 S
Units : mm
Reference Stopper Series AL Reference
Nominal Withdrawal Sleeve Numbers Nominal Basic Dimensions Mass (kg)
Numbers Numbers per 100 pcs Nut Numbers
AH 30 AH 31 AH 2 AH 22 AH 32 AH 3 AH 23 t1 S L2 s1 i L3 approx.
AN 09 AH 208 AH 308 AH 2308 AL 44 4 20 12 9 22.5 30.5 2.6 AN 44, AN 48

AN 10 AH 209 AH 309 AH 2309 AL 52 4 24 12 12 25.5 33.5 3.4 AN 52, AN 56
AN 11 AH 210 AHX 310 AHX 2310 AL 60 4 24 12 12 30.5 38.5 3.8 AN 60
AN 12 AH 211 AHX 311 AHX 2311

AN 13 AH 212 AHX 312 AHX 2312 AL 64 5 24 15 12 31 41 5.35 AN 64
AN 14 AL 68 5 28 15 14 38 48 6.65 AN 68, AN 72
AL 76 5 32 15 14 40 50 7.95 AN 76
AN 15 AH 213 AH 313 AH 2313
AN 16 AH 214 AH 314 AHX 2314
AN 17 AH 215 AH 315 AHX 2315 AL 80 5 32 15 18 45 55 8.2 AN 80, AN 84
AL 88 5 36 15 18 43 53 9.0 AN 88, AN 92
AN 18 AH 216 AH 316 AHX 2316 AL 96 5 36 15 18 53 63 10.4 AN 96
AN 19 AH 217 AHX 317 AHX 2317 AL 100 5 40 15 18 45 55 10.5 AN 100
AN 20 AH 218 AHX 3218 AHX 318 AHX 2318
Stopper Series ALL
AN 21 AH 219 AHX 319 AHX 2319
AN 22 AH 220 AHX 3220 AHX 320 AHX 2320
AN 23 AH 221 AHX 321 ALL 44 4 20 12 7 13.5 21.5 2.12 ANL 44
ALL 48 4 20 12 9 17.5 25.5 2.29 ANL 48, ANL 52
ALL 56 4 24 12 9 17.5 25.5 2.92 ANL 56
AN 24 AHX 3122 AH 222 AHX 322
AN 25 AHX 3222 AHX 2322
AN 26 AHX 3024 AHX 3124 AH 224 AHX 324
ALL 60 4 24 12 9 20.5 28.5 3.15 ANL 60
AN 27 AHX 3224 AHX 2324 ALL 64 5 24 15 9 21 31 4.55 ANL 64, ANL 68
AN 28 AHX 3026 AHX 3126 AH 226 AHX 326 ALL 72 5 28 15 9 20 30 5.05 ANL 72
AN 29 AHX 3226 AHX 2326
AN 30 AHX 3028 AHX 3128 AH 228 AHX 328 ALL 76 5 28 15 12 24 34 5.3 ANL 76, ANL 80
AN 31 AHX 3228 AHX 2328 ALL 84 5 32 15 12 24 34 6.1 ANL 84
AN 32 AHX 3030 AH 230 ALL 88 5 32 15 14 28 38 6.45 ANL 88, ANL 92
ALL 96 5 36 15 14 28 38 7.3 ANL 96, ANL 100
AN 33 AHX 3130 AHX 3230 AHX 330 AHX 2330
AN 34 AH 3032 AH 232
AN 36 AH 3034 AH 3132 AH 234 AH 3232 AH 332 AH 2332
AN 38 AH 3036 AH 3134 AH 236 AH 3234 AH 334 AH 2334

AN 40 AH 3136 AH 2236 AH 3236 AH 2336
B 376 B 377
B356-379E.indd 376-377 11/20/13 5:03:11 PM

LOCK-WASHERS FOR ROLLING BEARINGS
25 25 25 25
f f f f
r r
f1 B2 f1 f1 B2 f1
B1 B1 B1 B1
M jd 4 jd5 M jd 4 jd5 M jd 4 jd5 M jd 4 jd5
d3 d3 d3 d3
Bent-Tab Straight-Tab Bent-Tab Straight-Tab

Lock-washer Series AW Reference Lock-washer Series AW Reference
Nominal Numbers Nominal Numbers
Basic Dimensions Mass (kg) Adapter (1) Basic Dimensions Mass (kg) Adapter (1)
No. of Nut Shaft No. of Nut Shaft
Sleeve Bore
per 100 pcs Sleeve Bore
per 100 pcs
Bent-Tab Straight-Tab Bent-Tab Teeth Numbers Dia. Bent-Tab Straight-Tab Bent-Tab Teeth Numbers Dia.
d3 M f1 B1 f d4 d5 r B2 approx. Dia. Numbers d3 M f1 B1 f d4 d5 r B2 approx. Dia. Numbers
AW 02 AW 02 X 15 13.5 4 1 4 21 28 1 2.5 13 0.253 AN 02 15 AW 26 AW 26 X 130 125 14 2 12 149 175 1.5 6 19 11.3 26 AN 26 130
AW 03 AW 03 X 17 15.5 4 1 4 24 32 1 2.5 13 0.315 AN 03 17 AW 27 AW 27 X 135 130 14 2 14 160 185 1.5 6 19 14.4 AN 27 135
AW 04 AW 04 X 20 18.5 4 1 4 26 36 1 2.5 13 0.35 04 AN 04 20 AW 28 AW 28 X 140 135 16 2 14 160 192 1.5 8 19 14.2 28 AN 28 140
AW 05 AW 05 X 25 23 5 1.2 5 32 42 1 2.5 13 0.64 05 AN 05 25 AW 29 AW 29 X 145 140 16 2 14 172 202 1.5 8 19 16.8 AN 29 145
AW 06 AW 06 X 30 27.5 5 1.2 5 38 49 1 2.5 13 0.78 06 AN 06 30 AW 30 AW 30 X 150 145 16 2 14 171 205 1.5 8 19 15.9 30 AN 30 150
AW 07 AW 07 X 35 32.5 6 1.2 5 44 57 1 2.5 15 1.04 07 AN 07 35 AW 31 AW 31 X 155 147.5 16 2.5 16 182 212 1.5 8 19 20.9 AN 31 155
AW 08 AW 08 X 40 37.5 6 1.2 6 50 62 1 2.5 15 1.23 08 AN 08 40 AW 32 AW 32 X 160 154 18 2.5 16 182 217 1.5 8 19 22.2 32 AN 32 160
AW 09 AW 09 X 45 42.5 6 1.2 6 56 69 1 2.5 17 1.52 09 AN 09 45 AW 33 AW 33 X 165 157.5 18 2.5 16 193 222 1.5 8 19 24.1 AN 33 165
AW 10 AW 10 X 50 47.5 6 1.2 6 61 74 1 2.5 17 1.6 10 AN 10 50 AW 34 AW 34 X 170 164 18 2.5 16 193 232 1.5 8 19 24.7 34 AN 34 170
AW 11 AW 11 X 55 52.5 8 1.2 7 67 81 1 4 17 1.96 11 AN 11 55 AW 36 AW 36 X 180 174 20 2.5 18 203 242 1.5 8 19 26.8 36 AN 36 180
AW 12 AW 12 X 60 57.5 8 1.5 7 73 86 1.2 4 17 2.53 12 AN 12 60 AW 38 AW 38 X 190 184 20 2.5 18 214 252 1.5 8 19 27.8 38 AN 38 190
AW 13 AW 13 X 65 62.5 8 1.5 7 79 92 1.2 4 19 2.9 13 AN 13 65 AW 40 AW 40 X 200 194 20 2.5 18 226 262 1.5 8 19 29.3 40 AN 40 200
Washer Series AWL

AW 14 AW 14 X 70 66.5 8 1.5 8 85 98 1.2 4 19 3.35 14 AN 14 70
AW 15 AW 15 X 75 71.5 8 1.5 8 90 104 1.2 4 19 3.55 15 AN 15 75 AWL 24 AWL 24 X 120 115 14 2 12 133 155 1.5 6 19 7.7 24 ANL 24 120
AWL 28 AWL 28 X 140 135 16 2 14 151 175 1.5 8 19 10.9 28 ANL 28 140
AW 17 AW 17 X 85 81.5 10 1.8 8 102 119 1.2 4 19 5.25 17 AN 17 85
AW 19 AW 19 X 95 91.5 10 1.8 10 113 133 1.2 4 19 6.7 19 AN 19 95 AWL 32 AWL 32 X 160 154 18 2.5 16 174 200 1.5 8 19 16.2 32 ANL 32 160
AWL 34 AWL 34 X 170 164 18 2.5 16 184 210 1.5 8 19 19 34 ANL 34 170
AW 20 AW 20 X 100 96.5 12 1.8 10 120 142 1.2 6 19 7.65 20 AN 20 100
AW 21 AW 21 X 105 100.5 12 1.8 12 126 145 1.2 6 19 8.25 21 AN 21 105 AWL 36 AWL 36 X 180 174 20 2.5 18 192 220 1.5 8 19 18 36 ANL 36 180
AW 22 AW 22 X 110 105.5 12 1.8 12 133 154 1.2 6 19 9.4 22 AN 22 110 AWL 38 AWL 38 X 190 184 20 2.5 18 202 230 1.5 8 19 20.5 38 ANL 38 190
AWL 40 AWL 40 X 200 194 20 2.5 18 218 250 1.5 8 19 21.4 40 ANL 40 200
AW 23 AW 23 X 115 110.5 12 2 12 137 159 1.5 6 19 10.8 AN 23 115 Note (1) Series AW is applicable to adapter sleeve Series A31 and A23.
AW 24 AW 24 X 120 115 14 2 12 138 164 1.5 6 19 10.5 24 AN 24 120 Series AWL is applicable to adapter sleeve Series A30.
AW 25 AW 25 X 125 120 14 2 12 148 170 1.5 6 19 11.8 AN 25 125 Remarks Lock-washers with straight tabs shall be used with adapter sleeves having narrow slits, and for those having wide slits,
either type of lock-washer may be used.
Note (1) Applicable to adapter sleeve Series A31, A2, A3, and A23.
Remarks Lock-washers with straight tabs shall be used with adapter sleeves having narrow slits, and for those having wide slits,
either type of lock-washer may be used.
B 378 B 379
B356-379E.indd 378-379 11/20/13 5:03:11 PM

INTRODUCTION OF NSK PRODUCTSAPPENDICES
INTRODUCTION OF NSK PRODUCTS

Page
Photos of NSK Products C 2
APPENDICES
Appendix Table 1 Conversion from SI (International Units) System C 8
Appendix Table 2 Nkgf Force Conversion Table C10
Appendix Table 3 kglb Mass Conversion Table C11
Appendix Table 4 CF Temperature Conversion Table C12
Appendix Table 5 Viscosity Conversion Table C13
Appendix Table 6 inchmm Dimension Conversion Table C14
Appendix Table 7 Hardness Conversion Table C16
Appendix Table 8 Physical and Mechanical Properties of Materials C17
Appendix Table 9 Tolerances for Shaft Diameters C18
Appendix Table 10 Tolerances for Housing Bore Diameters C20
Appendix Table 11 Values of Standard Tolerance Grades IT C22
Appendix Table 12 Speed Factor fn C24
Appendix Table 13 Fatigue Life Factor fh and Fatigue Life L Lh C25
Appendix Table 14 Index of Inch Design Tapered Roller Bearings C26
C1
C001-034E.indd 1 11/20/13 5:03:32 PM

AUTOMOTIVE PRODUCTS PRECISION MACHINE COMPONENTS
BALL SCREWS
Column Type Electric Power Steering Pinion Type Electric Power Steering
(CAT.No. E4102) (CAT.No. E4102) NSK Standard Ball Screws NSK Standard Ball Screws High-Speed, Low-Noise Ball Screws
Compact FA Series High Speed SS Series BSS Series
(CAT. No. E3239, E3162) (CAT.No.E3241) (CAT. No. E3162)
Ball Screws for Twin-Drive Systems

TW Series
Ball Screws for High-Speed Machine Tools (CAT. No. E3162) Ball Screws for High-Load Drive
HMD Series HTF-SRC Series, HTF-SRD Series,
(CAT. No. E3162) HTF Series, A1 Series
Offeet Ball Screw Type Electric Power Steering Long Life Water Pump Bearings
(CAT. No. E3238, E3162)
(CAT.No. E4102) (CAT.No. E396, E4102)
Highly Dust-Resistant Ball Screws,

NSK Linear Guides
V1 Series
(CAT. No. E3162)
MONOCARRIERS Ball Screws, NSK Linear Guides with

NSK K1 Lubrication Unit
(CAT. No. E3331, E3162)
Ball Screws, NSK Linear Guides

with E-DFO Thin-Film Lubrication for
Vacuum Environments
(CAT. No. E1258)
Hub Unit Bearings One-Way Clutch
(CAT.No. E4201)
Monocarriers Toughcarrier
C2 (CAT. No. E3419, E3162) (CAT. No. E3421) C3
C001-034E.indd 2-3 11/20/13 5:03:33 PM

PRECISION MACHINE COMPONENTS PRECISION MACHINE COMPONENTS
LINEAR BEARINGS MECHATRONIC ACTUATORS
Megatorque XY
Motor Modules
(CAT.No. E3511)
NSK Linear Guides NSK Linear Guides NSK Low-Noise Linear Guides
Roller Guides RA Series LH Series, LS Series SH Series, SS Series
(CAT. No. E3328, E3162) (CAT. No. E3162) (CAT. No. E3162)
Megapositioner XY Tables
NSK Linear Guides NSK Linear Guides NSK Linear Guides

High-Accuracy Series Miniature PU Series, PE Series TS Series
(CAT. No. E3329, E3162) (CAT. No. E3327, E3162) (CAT. No. E3324, E3162)
ASSORTED SPINDLES
Live Centers
Precision Grinding (CAT.No. E2202)
High Speed Integrated Motor Spindles Spindles
(CAT.No. E2202)
Positioning Air Bearing
Actuator Slides
Oil/Air Lubricating Unit, Standard Type Precision

Fine Lube Boring Heads
(CAT.No. E1254/A1387) (CAT.No. E2202)
Spindles for Electrical and

Electric Equipment
C4 C5
C001-034E.indd 4-5 11/20/13 5:03:45 PM

AIR SPINDLES RELATED PRODUCT WITH BEARING
Air-spindle
Air Cleaner Unit
Bearing Induction Heater Extra Small Bearing Monitor
(CAT.No. E398) NB-4
(Bearing Abnormality Detector)
(CAT.No. E410)
Large Size Proximity Stepper RZ Series
C6 C7
C001-034E.indd 6-7 11/20/13 5:03:52 PM

APPENDICES
Appendix Table 1 Conversion Table from SI (International Units) System
Comparison of SI, CGS, and Engineering Units Prefixes Used In SI System
Units Multiples Prefix Symbols Multiples Prefix Symbols

Length Mass Time Temp. Acceleration Force Stress Pressure Energy Power
Unit System
1018 Exa E 101 Deci d
1015 Peta P 102 Centi c
SI m kg s K, C m/s2 N Pa Pa J W 1012 Tera T 103 Milli m
CGS System cm g s C Gal dyn dyn/cm2 dyn/cm2 erg erg/s 109 Giga G 106 Micro
106 Mega M 109 Nano n
Engineering 103 Kilo k 1012 Pico p
Unit System m kgf s2/m s C m/s2 kgf kgf/m2 kgf/m2 kgf m kgf m/s
102 Hecto h 1015 Femto f
10 Deca da 1018 Ato a
Conversion Factors from SI Units Conversion Factors from SI Units (Continued)
S I Units Units other than SI S I Units Units other than S I

Parameter Conversion Factors Conversion Factors
from SI Units Parameter
from S I Units
Names of Units Symbols Name of Units Symbols Names of Units Symbols Names of Units Units
Angle Radian rad Degree 180/ Pressure Pascal Pa Kilogram-force per square meter kgf/m2 1/9.806 65
Minute 10 800/ (Newton per square meter) (N/m2) Water Column mH2O 1/(9.806 65103)
Second 648 000/ Mercury Column mmHg 760/(1.013 25105)
Torr Torr 760/(1.013 25105)
Length Meter m Micron 106 Bar bar 105
Angstrom 1010 Atmosphere atm 1/(1.013 25105)
Area Square meter m2 Are a 102 Energy Joule J Erg erg 107
Hectare ha 104 (Newton meter) (N m) Calorie (International) calIT 1/4.186 8
Kilogram-force meter kgf m 1/9.806 65
Volume Cubic meter m3 Liter l, L 103 Kilowatt hour kW h 1/(3.6106)
Deciliter dl, dL 104 French horse power hour PS h 3.776 72107
Time Second s Minute min 1/60 Work Watt W Kilogram-force meter per second kgf m/s 1/9.806 65
Hour h 1/3 600 (Joule per second) (J/s) Kilocalorie per hour kcal/h 1/1.163
Day d 1/86 400 French horse power PS 1/735.498 8
Frequency Hertz Hz Cycle s1 1 Viscosity, Viscosity Index Pascal second Pa s Poise P 10
1
Speed of Rotation Revolution per second s Revolution per miunte rpm 60 Kinematic Viscosity, Square meter per second 2
m /s Stokes St 104
Kinematic Viscosity Index Centistokes cSt 106
Speed Meter per second m/s Kilometer per hour km/h 3 600/1 000
Knot kn 3 600/1 852 Temperature Kelvin, Degree celsius K, C Degree C (See note (1))
Acceleration Meter per second per second m/s 2

Gal Gal 10 2 Electric Current, Ampere A Ampere A 1
Magnetomotive Force
g G 1/9.806 65
Voltage, Electromotive Force Volt V (Watts per ampere) (W/A) 1
Mass Kilogram kg Ton t 103
Magnetic Field Strength Ampere per meter A/m Oersted Oe 4/103
Force Newton N Kilogram-force kgf 1/9.806 65
Ton-force tf 1/ (9.806 65103) Magnetic Flux Tesla T Gauss Gs 104
Dyne dyn 105 Density Gamma 109
Torque or Moment Newton meter Nm Kilogram-force meter kgf m 1/9.806 65 Electrical Resistance Ohm (Volts per ampere) (V/A) 1
Note 1
() The conversion from T K into C is =T273.15 but for a temperature difference, it is & T =& . However,
Stress Pascal Pa Kilogram-force per square centimeter kgf/cm2 1/ (9.806 65104) & T and & represent temperature differences measured using the Kelvin and Celsius scales respectively.
(N/m2) Kilogram-force per square millimeter kgf/mm2 1/ (9.806 65106) Remarks The names and symbols in ( ) are equivalent to those directly above them or on their left.
Example of conversion 1N=1/9.806 65kgf
C8 C9
C001-034E.indd 8-9 11/20/13 5:03:53 PM

APPENDICES
Appendix Table 2 N-kgf Conversion Table Appendix Table 3 kg-lb Conversion Table
[Method of using this table] For example, to convert 10N into kgf, read the figure in the right kgf [Method of using this table] For example, to convert 10kg into lb, read the figure in the right lb
column adjacent to the 10 in the center column in the 1st block. This column adjacent to the 10 in the center column in the 1st block. This
means that 10N is 1.0197kgf. To convert 10kgf into N, read the figure 1 N=0.1019716 kgf means that 10kg is 22.046lb. To convert 10lb into kg, read the figure 1 kg=2.2046226 lb
in the left N column of the same row, which indicates that the answer in the left kg column of the same row, which indicates that the answer
1 kgf=9.80665 N 1 lb=0.45359237 kg
is 98.066N. is 4.536kg.
N kgf N kgf N kgf kg lb kg lb kg lb
9.8066 1 0.1020 333.43 34 3.4670 657.05 67 6.8321 0.454 1 2.205 15.422 34 74.957 30.391 67 147.71
19.613 2 0.2039 343.23 35 3.5690 666.85 68 6.9341 0.907 2 4.409 15.876 35 77.162 30.844 68 149.91
29.420 3 0.3059 353.04 36 3.6710 676.66 69 7.0360 1.361 3 6.614 16.329 36 79.366 31.298 69 152.12
39.227 4 0.4079 362.85 37 3.7729 686.47 70 7.1380 1.814 4 8.818 16.783 37 81.571 31.751 70 154.32
49.033 5 0.5099 372.65 38 3.8749 696.27 71 7.2400 2.268 5 11.023 17.237 38 83.776 32.205 71 156.53
58.840 6 0.6118 382.46 39 3.9769 706.08 72 7.3420 2.722 6 13.228 17.690 39 85.980 32.659 72 158.73
68.647 7 0.7138 392.27 40 4.0789 715.89 73 7.4439 3.175 7 15.432 18.144 40 88.185 33.112 73 160.94
78.453 8 0.8158 402.07 41 4.1808 725.69 74 7.5459 3.629 8 17.637 18.597 41 90.390 33.566 74 163.14
88.260 9 0.9177 411.88 42 4.2828 735.50 75 7.6479 4.082 9 19.842 19.051 42 92.594 34.019 75 165.35
98.066 10 1.0197 421.69 43 4.3848 745.31 76 7.7498 4.536 10 22.046 19.504 43 94.799 34.473 76 167.55
107.87 11 1.1217 431.49 44 4.4868 755.11 77 7.8518 4.990 11 24.251 19.958 44 97.003 34.927 77 169.76
117.68 12 1.2237 441.30 45 4.5887 764.92 78 7.9538 5.443 12 26.455 20.412 45 99.208 35.380 78 171.96
127.49 13 1.3256 451.11 46 4.6907 774.73 79 8.0558 5.897 13 28.660 20.865 46 101.41 35.834 79 174.17
137.29 14 1.4276 460.91 47 4.7927 784.53 80 8.1577 6.350 14 30.865 21.319 47 103.62 36.287 80 176.37
147.10 15 1.5296 470.72 48 4.8946 794.34 81 8.2597 6.804 15 33.069 21.772 48 105.82 36.741 81 178.57
156.91 16 1.6315 480.53 49 4.9966 804.15 82 8.3617 7.257 16 35.274 22.226 49 108.03 37.195 82 180.78
166.71 17 1.7335 490.33 50 5.0986 813.95 83 8.4636 7.711 17 37.479 22.680 50 110.23 37.648 83 182.98
176.52 18 1.8355 500.14 51 5.2006 823.76 84 8.5656 8.165 18 39.683 23.133 51 112.44 38.102 84 185.19
186.33 19 1.9375 509.95 52 5.3025 833.57 85 8.6676 8.618 19 41.888 23.587 52 114.64 38.555 85 187.39
196.13 20 2.0394 519.75 53 5.4045 843.37 86 8.7696 9.072 20 44.092 24.040 53 116.84 39.009 86 189.60
205.94 21 2.1414 529.56 54 5.5065 853.18 87 8.8715 9.525 21 46.297 24.494 54 119.05 39.463 87 191.80
215.75 22 2.2434 539.37 55 5.6084 862.99 88 8.9735 9.979 22 48.502 24.948 55 121.25 39.916 88 194.01
225.55 23 2.3453 549.17 56 5.7104 872.79 89 9.0755 10.433 23 50.706 25.401 56 123.46 40.370 89 196.21
235.36 24 2.4473 558.98 57 5.8124 882.60 90 9.1774 10.886 24 52.911 25.855 57 125.66 40.823 90 198.42
245.17 25 2.5493 568.79 58 5.9144 892.41 91 9.2794 11.340 25 55.116 26.308 58 127.87 41.277 91 200.62
254.97 26 2.6513 578.59 59 6.0163 902.21 92 9.3814 11.793 26 57.320 26.762 59 130.07 41.730 92 202.83
264.78 27 2.7532 588.40 60 6.1183 912.02 93 9.4834 12.247 27 59.525 27.216 60 132.28 42.184 93 205.03
274.59 28 2.8552 598.21 61 6.2203 921.83 94 9.5853 12.701 28 61.729 27.669 61 134.48 42.638 94 207.23
284.39 29 2.9572 608.01 62 6.3222 931.63 95 9.6873 13.154 29 63.934 28.123 62 136.69 43.091 95 209.44
294.20 30 3.0591 617.82 63 6.4242 941.44 96 9.7893 13.608 30 66.139 28.576 63 138.89 43.545 96 211.64
304.01 31 3.1611 627.63 64 6.5262 951.25 97 9.8912 14.061 31 68.343 29.030 64 141.10 43.998 97 213.85
313.81 32 3.2631 637.43 65 6.6282 961.05 98 9.9932 14.515 32 70.548 29.484 65 143.30 44.452 98 216.05
323.62 33 3.3651 647.24 66 6.7301 970.86 99 10.095 14.969 33 72.753 29.937 66 145.51 44.906 99 218.26
C 10 C 11
C001-034E.indd 10-11 11/20/13 5:03:54 PM

APPENDICES
Appendix Table 4 C-F Conversion Table Appendix Table 5 Viscosity Conversion Table
[Method of using this table] For example, to convert 38C into F, read the figure in the right F
C= 5 (F32)
column adjacent to the 38 in the center column in the 2nd block. This 9
means that 38C is 100.4F. To convert 38F into C, read the figure 9
in the left C column of the same row, which indicates that the answer F=32+ C
5
is 3.3C.
Saybolt No.1 Type Saybolt No.1 Type

C F C F C F C F Kinematic Universal Redwood Kinematic Universal Redwood
Engler Engler
Viscosity SUS (sec) R (sec) Viscosity SUS (sec) R (sec)
E (degree) E (degree)
73.3 100 148.0 0.0 32 89.6 21.7 71 159.8 43.3 110 230 mm2/s mm2/s
62.2 80 112.0 0.6 33 91.4 22.2 72 161.6 46.1 115 239 100F 210F 50C 100C 100F 210F 50C 100C
51.1 60 76.0 1.1 34 93.2 22.8 73 163.4 48.9 120 248
40.0 40 40.0 1.7 35 95.0 23.3 74 165.2 51.7 125 257 2 32.6 32.8 30.8 31.2 1.14 35 163 164 144 147 4.70
34.4 30 22.0 2.2 36 96.8 23.9 75 167.0 54.4 130 266 3 36.0 36.3 33.3 33.7 1.22 36 168 170 148 151 4.83
4 39.1 39.4 35.9 36.5 1.31 37 172 173 153 155 4.96
5 42.3 42.6 38.5 39.1 1.40 38 177 178 156 159 5.08
28.9 20 4.0 2.8 37 98.6 24.4 76 168.8 57.2 135 275 6 45.5 45.8 41.1 41.7 1.48 39 181 183 160 164 5.21
23.3 10 14.0 3.3 38 100.4 25.0 77 170.6 60.0 140 284
17.8 0 32.0 3.9 39 102.2 25.6 78 172.4 65.6 150 302
17.2 1 33.8 4.4 40 104.0 26.1 79 174.2 71.1 160 320 7 48.7 49.0 43.7 44.3 1.56 40 186 187 164 168 5.34
16.7 2 35.6 5.0 41 105.8 26.7 80 176.0 76.7 170 338 8 52.0 52.4 46.3 47.0 1.65 41 190 192 168 172 5.47
9 55.4 55.8 49.1 50.0 1.75 42 195 196 172 176 5.59
10 58.8 59.2 52.1 52.9 1.84 43 199 201 176 180 5.72
16.1 3 37.4 5.6 42 107.6 27.2 81 177.8 82.2 180 356 11 62.3 62.7 55.1 56.0 1.93 44 204 205 180 185 5.85
15.6 4 39.2 6.1 43 109.4 27.8 82 179.6 87.8 190 374
15.0 5 41.0 6.7 44 111.2 28.3 83 181.4 93.3 200 392
14.4 6 42.8 7.2 45 113.0 28.9 84 183.2 98.9 210 410 12 65.9 66.4 58.2 59.1 2.02 45 208 210 184 189 5.98
13.9 7 44.6 7.8 46 114.8 29.4 85 185.0 104.4 220 428 13 69.6 70.1 61.4 62.3 2.12 46 213 215 188 193 6.11
14 73.4 73.9 64.7 65.6 2.22 47 218 219 193 197 6.24
15 77.2 77.7 68.0 69.1 2.32 48 222 224 197 202 6.37
13.3 8 46.4 8.3 47 116.6 30.0 86 186.8 110.0 230 446 16 81.1 81.7 71.5 72.6 2.43 49 227 228 201 206 6.50
12.8 9 48.2 8.9 48 118.4 30.6 87 188.6 115.6 240 464
12.2 10 50.0 9.4 49 120.2 31.1 88 190.4 121.1 250 482
11.7 11 51.8 10.0 50 122.0 31.7 89 192.2 148.9 300 572 17 85.1 85.7 75.0 76.1 2.54 50 231 233 205 210 6.63
11.1 12 53.6 10.6 51 123.8 32.2 90 194.0 176.7 350 662 18 89.2 89.8 78.6 79.7 2.64 55 254 256 225 231 7.24
19 93.3 94.0 82.1 83.6 2.76 60 277 279 245 252 7.90
20 97.5 98.2 85.8 87.4 2.87 65 300 302 266 273 8.55
10.6 13 55.4 11.1 52 125.6 32.8 91 195.8 204 400 752 21 102 102 89.5 91.3 2.98 70 323 326 286 294 9.21
10.0 14 57.2 11.7 53 127.4 33.3 92 197.6 232 450 842
9.4 15 59.0 12.2 54 129.2 33.9 93 199.4 260 500 932
8.9 16 60.8 12.8 55 131.0 34.4 94 201.2 288 550 1022 22 106 107 93.3 95.1 3.10 75 346 349 306 315 9.89
8.3 17 62.6 13.3 56 132.8 35.0 95 203.0 316 600 1112 23 110 111 97.1 98.9 3.22 80 371 373 326 336 10.5
24 115 115 101 103 3.34 85 394 397 347 357 11.2
25 119 120 105 107 3.46 90 417 420 367 378 11.8
7.8 18 64.4 13.9 57 134.6 35.6 96 204.8 343 650 1202 26 123 124 109 111 3.58 95 440 443 387 399 12.5
7.2 19 66.2 14.4 58 136.4 36.1 97 206.6 371 700 1292
6.7 20 68.0 15.0 59 138.2 36.7 98 208.4 399 750 1382
6.1 21 69.8 15.6 60 140.0 37.2 99 210.2 427 800 1472 27 128 129 112 115 3.70 100 464 467 408 420 13.2
5.6 22 71.6 16.1 61 141.8 37.8 100 212.0 454 850 1562 28 132 133 116 119 3.82 120 556 560 490 504 15.8
29 137 138 120 123 3.95 140 649 653 571 588 18.4
30 141 142 124 127 4.07 160 742 747 653 672 21.1
5.0 23 73.4 16.7 62 143.6 38.3 101 213.8 482 900 1652 31 145 146 128 131 4.20 180 834 840 734 757 23.7
4.4 24 75.2 17.2 63 145.4 38.9 102 215.6 510 950 1742
3.9 25 77.0 17.8 64 147.2 39.4 103 217.4 538 1000 1832
3.3 26 78.8 18.3 65 149.0 40.0 104 219.2 593 1100 2012 32 150 150 132 135 4.32 200 927 933 816 841 26.3
2.8 27 80.6 18.9 66 150.8 40.6 105 221.0 649 1200 2192 33 154 155 136 139 4.45 250 1 159 1 167 1 020 1 051 32.9
34 159 160 140 143 4.57 300 1 391 1 400 1 224 1 241 39.5
2.2 28 82.4 19.4 67 152.6 41.1 106 222.8 704 1300 2372 Remarks 1mm2/s=1cSt
1.7 29 84.2 20.0 68 154.4 41.7 107 224.6 760 1400 2552
1.1 30 86.0 20.6 69 156.2 42.2 108 226.4 816 1500 2732
0.6 31 87.8 21.1 70 158.0 42.8 109 228.2 871 1600 2912
C 12 C 13
C001-034E.indd 12-13 11/20/13 5:03:55 PM

APPENDICES
Appendix Table 6 inch - mm Conversion Table 1=25.4 mm 1=25.4 mm

inch 0 1 2 3 4 5 6 7 8 9 10 inch 11 12 13 14 15 16 17 18 19 20
Fraction Decimal mm Fraction Decimal mm

0 0.000000 0.000 25.400 50.800 76.200 101.600 127.000 152.400 177.800 203.200 228.600 254.000 0 0.0000 279.400 304.800 330.200 355.600 381.000 406.400 431.800 457.200 482.600 508.000
1/64 0.015625 0.397 25.797 51.197 76.597 101.997 127.397 152.797 178.197 203.597 228.997 254.397 1/16 0.0625 280.988 306.388 331.788 357.188 382.588 407.988 433.388 458.788 484.188 509.588
1/32 0.031250 0.794 26.194 51.594 76.994 102.394 127.794 153.194 178.594 203.994 229.394 254.794 1/8 0.1250 282.575 307.975 333.375 358.775 384.175 409.575 434.975 460.375 485.775 511.175
3/64 0.046875 1.191 26.591 51.991 77.391 102.791 128.191 153.591 178.991 204.391 229.791 255.191 3/16 0.1875 284.162 309.562 334.962 360.362 385.762 411.162 436.562 461.962 487.362 512.762
1/16 0.062500 1.588 26.988 52.388 77.788 103.188 128.588 153.988 179.388 204.788 230.188 255.588 1/4 0.2500 285.750 311.150 336.550 361.950 387.350 412.750 438.150 463.550 488.950 514.350
5/64 0.078125 1.984 27.384 52.784 78.184 103.584 128.984 154.384 179.784 205.184 230.584 255.984 5/16 0.3125 287.338 312.738 338.138 363.538 388.938 414.338 439.738 465.138 490.538 515.938
3/32 0.093750 2.381 27.781 53.181 78.581 103.981 129.381 154.781 180.181 205.581 230.981 256.381 3/8 0.3750 288.925 314.325 339.725 365.125 390.525 415.925 441.325 466.725 492.125 517.525
7/64 0.109375 2.778 28.178 53.578 78.978 104.378 129.778 155.178 180.578 205.978 231.378 256.778 7/16 0.4375 290.512 315.912 341.312 366.712 392.112 417.512 442.912 468.312 493.712 519.112
1/8 0.125000 3.175 28.575 53.975 79.375 104.775 130.175 155.575 180.975 206.375 231.775 257.175 1/2 0.5000 292.100 317.500 342.900 368.300 393.700 419.100 444.500 469.900 495.300 520.700
9/64 0.140625 3.572 28.972 54.372 79.772 105.172 130.572 155.972 181.372 206.772 232.172 257.572 9/16 0.5625 293.688 319.088 344.488 369.888 395.288 420.688 446.088 471.488 496.888 522.288
5/32 0.156250 3.969 29.369 54.769 80.169 105.569 130.969 156.369 181.769 207.169 232.569 257.969 5/8 0.6250 295.275 320.675 346.075 371.475 396.875 422.275 447.675 473.075 498.475 523.875
11/64 0.171875 4.366 29.766 55.166 80.566 105.966 131.366 156.766 182.166 207.566 232.966 258.366 11/16 0.6875 296.862 322.262 347.662 373.062 398.462 423.862 449.262 474.662 500.062 525.462
3/16 0.187500 4.762 30.162 55.562 80.962 106.362 131.762 157.162 182.562 207.962 233.362 258.762 3/4 0.7500 298.450 323.850 349.250 374.650 400.050 425.450 450.850 476.250 501.650 527.050
13/64 0.203125 5.159 30.559 55.959 81.359 106.759 132.159 157.559 182.959 208.359 233.759 259.159 13/16 0.8125 300.038 325.438 350.838 376.238 401.638 427.038 452.438 477.838 503.238 528.638
7/32 0.218750 5.556 30.956 56.356 81.756 107.156 132.556 157.956 183.356 208.756 234.156 259.556 7/8 0.8750 301.625 327.025 352.425 377.825 403.225 428.625 454.025 479.425 504.825 530.225
15/64 0.234375 5.953 31.353 56.753 82.153 107.553 132.953 158.353 183.753 209.153 234.553 259.953 15/16 0.9375 303.212 328.612 354.012 379.412 404.812 430.212 455.612 481.012 506.412 531.812
1/4 0.250000 6.350 31.750 57.150 82.550 107.950 133.350 158.750 184.150 209.550 234.950 260.350
17/64 0.265625 6.747 32.147 57.547 82.947 108.347 133.747 159.147 184.547 209.947 235.347 260.747
9/32 0.281250 7.144 32.544 57.944 83.344 108.744 134.144 159.544 184.944 210.344 235.744 261.144
19/64 0.296875 7.541 32.941 58.341 83.741 109.141 134.541 159.941 185.341 210.741 236.141 261.541 1=25.4 mm
5/16 0.312500 7.938 33.338 58.738 84.138 109.538 134.938 160.338 185.738 211.138 236.538 261.938
inch 21 22 23 24 25 26 27 28 29 30
21/64 0.328125 8.334 33.734 59.134 84.534 109.934 135.334 160.734 186.134 211.534 236.934 262.334
11/32 0.343750 8.731 34.131 59.531 84.931 110.331 135.731 161.131 186.531 211.931 237.331 262.731
23/64 0.359375 9.128 34.528 59.928 85.328 110.728 136.128 161.528 186.928 212.328 237.728 263.128 Fraction Decimal mm
3/8 0.375000 9.525 34.925 60.325 85.725 111.125 136.525 161.925 187.325 212.725 238.125 263.525 0 0.0000 533.400 558.800 584.200 609.600 635.000 660.400 685.800 711.200 736.600 762.000
25/64 0.390625 9.922 35.322 60.722 86.122 111.522 136.922 162.322 187.722 213.122 238.522 263.922 1/16 0.0625 534.988 560.388 585.788 611.188 636.588 661.988 687.388 712.788 738.188 763.588
13/32 0.406250 10.319 35.719 61.119 86.519 111.919 137.319 162.719 188.119 213.519 238.919 264.319 1/8 0.1250 536.575 561.975 587.375 612.775 638.175 663.575 688.975 714.375 739.775 765.175
27/64 0.421875 10.716 36.116 61.516 86.916 112.316 137.716 163.116 188.516 213.916 239.316 264.716 3/16 0.1875 538.162 563.562 588.962 614.362 639.762 665.162 690.562 715.962 741.362 766.762
7/16 0.437500 11.112 36.512 61.912 87.312 112.712 138.112 163.512 188.912 214.312 239.712 265.112 1/4 0.2500 539.750 565.150 590.550 615.950 641.350 666.750 692.150 717.550 742.950 768.350
29/64 0.453125 11.509 36.909 62.309 87.709 113.109 138.509 163.909 189.309 214.709 240.109 265.509 5/16 0.3125 541.338 566.738 592.138 617.538 642.938 668.338 693.738 719.138 744.538 769.938
15/32 0.468750 11.906 37.306 62.706 88.106 113.506 138.906 164.306 189.706 215.106 240.506 265.906 3/8 0.3750 542.925 568.325 593.725 619.125 644.525 669.925 695.325 720.725 746.125 771.525
31/64 0.484375 12.303 37.703 63.103 88.503 113.903 139.303 164.703 190.103 215.503 240.903 266.303 7/16 0.4375 544.512 569.912 595.312 620.712 646.112 671.512 696.912 722.312 747.712 773.112
1/2 0.500000 12.700 38.100 63.500 88.900 114.300 139.700 165.100 190.500 215.900 241.300 266.700 1/2 0.5000 546.100 571.500 596.900 622.300 647.700 673.100 698.500 723.900 749.300 774.700
33/64 0.515625 13.097 38.497 63.897 89.297 114.697 140.097 165.497 190.897 216.297 241.697 267.097 9/16 0.5625 547.688 573.088 598.488 623.888 649.288 674.688 700.088 725.488 750.888 776.288
17/32 0.531250 13.494 38.894 64.294 89.694 115.094 140.494 165.894 191.294 216.694 242.094 267.494 5/8 0.6250 549.275 574.675 600.075 625.475 650.875 676.275 701.675 727.075 752.475 777.875
35/64 0.546875 13.891 39.291 64.691 90.091 115.491 140.891 166.291 191.691 217.091 242.491 267.891 11/16 0.6875 550.862 576.262 601.662 627.062 652.462 677.862 703.262 728.662 754.062 779.462
9/16 0.562500 14.288 39.688 65.088 90.488 115.888 141.288 166.688 192.088 217.488 242.888 268.288 3/4 0.7500 552.450 577.850 603.250 628.650 654.050 679.450 704.850 730.250 755.650 781.050
37/64 0.578125 14.684 40.084 65.484 90.884 116.284 141.684 167.084 192.484 217.884 243.284 268.684 13/16 0.8125 554.038 579.438 604.838 630.238 655.638 681.038 706.438 731.838 757.238 782.638
19/32 0.593750 15.081 40.481 65.881 91.281 116.681 142.081 167.481 192.881 218.281 243.681 269.081 7/8 0.8750 555.625 581.025 606.425 631.825 657.225 682.625 708.025 733.425 758.825 784.225
39/64 0.609375 15.478 40.878 66.278 91.678 117.078 142.478 167.878 193.278 218.678 244.078 269.478 15/16 0.9375 557.212 582.612 608.012 633.412 658.812 684.212 709.612 735.012 760.412 785.812
5/8 0.625000 15.875 41.275 66.675 92.075 117.475 142.875 168.275 193.675 219.075 244.475 269.875
41/64 0.640625 16.272 41.672 67.072 92.472 117.872 143.272 168.672 194.072 219.472 244.872 270.272
21/32 0.656250 16.669 42.069 67.469 92.869 118.269 143.669 169.069 194.469 219.869 245.269 270.669
43/64 0.671875 17.066 42.466 67.866 93.266 118.666 144.066 169.466 194.866 220.266 245.666 271.066 1=25.4 mm
11/16 0.687500 17.462 42.862 68.262 93.662 119.062 144.462 169.862 195.262 220.662 246.062 271.462
45/64 0.703125 17.859 43.259 68.659 94.059 119.459 144.859 170.259 195.659 221.059 246.459 271.859 inch 31 32 33 34 35 36 37 38 39 40
23/32 0.718750 18.256 43.656 69.056 94.456 119.856 145.256 170.656 196.056 221.456 246.856 272.256
47/64 0.734375 18.653 44.053 69.453 94.853 120.253 145.653 171.053 196.453 221.853 247.253 272.653 Fraction Decimal mm
3/4 0.750000 19.050 44.450 69.850 95.250 120.650 146.050 171.450 196.850 222.250 247.650 273.050
0 0.0000 787.400 812.800 838.200 863.600 889.000 914.400 939.800 965.200 990.600 1016.000
49/64 0.765625 19.447 44.847 70.247 95.647 121.047 146.447 171.847 197.247 222.647 248.047 273.447 1/16 0.0625 788.988 814.388 839.788 865.188 890.588 915.988 941.388 966.788 992.188 1017.588
25/32 0.781250 19.844 45.244 70.644 96.044 121.444 146.844 172.244 197.644 223.044 248.444 273.844 1/8 0.1250 790.575 815.975 841.375 866.775 892.175 917.575 942.975 968.375 993.775 1019.175
51/64 0.796875 20.241 45.641 71.041 96.441 121.841 147.241 172.641 198.041 223.441 248.841 274.241 3/16 0.1875 792.162 817.562 842.962 868.362 893.762 919.162 944.562 969.962 995.362 1020.762
13/16 0.812500 20.638 46.038 71.438 96.838 122.238 147.638 173.038 198.438 223.838 249.238 274.638 1/4 0.2500 793.750 819.150 844.550 869.950 895.350 920.750 946.150 971.550 996.950 1022.350
53/64 0.828125 21.034 46.434 71.834 97.234 122.634 148.034 173.434 198.834 224.234 249.634 275.034 5/16 0.3125 795.338 820.738 846.138 871.538 896.938 922.338 947.738 973.138 998.538 1023.938
27/32 0.843750 21.431 46.831 72.231 97.631 123.031 148.431 173.831 199.231 224.631 250.031 275.431 3/8 0.3750 796.925 822.325 847.725 873.125 898.525 923.925 949.325 974.725 1000.125 1025.525
55/64 0.859375 21.828 47.228 72.628 98.028 123.428 148.828 174.228 199.628 225.028 250.428 275.828 7/16 0.4375 798.512 823.912 849.312 874.712 900.112 925.512 950.912 976.312 1001.712 1027.112
7/8 0.875000 22.225 47.625 73.025 98.425 123.825 149.225 174.625 200.025 225.425 250.825 276.225 1/2 0.5000 800.100 825.500 850.900 876.300 901.700 927.100 952.500 977.900 1003.300 1028.700
57/64 0.890625 22.622 48.022 73.422 98.822 124.222 149.622 175.022 200.422 225.822 251.222 276.622 9/16 0.5625 801.688 827.088 852.488 877.888 903.288 928.688 954.088 979.488 1004.888 1030.288
29/32 0.906250 23.019 48.419 73.819 99.219 124.619 150.019 175.419 200.819 226.219 251.619 277.019 5/8 0.6250 803.275 828.675 854.075 879.475 904.875 930.275 955.675 981.075 1006.475 1031.875
59/64 0.921875 23.416 48.816 74.216 99.616 125.016 150.416 175.816 201.216 226.616 252.016 277.416 11/16 0.6875 804.862 830.262 855.662 881.062 906.462 931.862 957.262 982.662 1008.062 1033.462
15/16 0.937500 23.812 49.212 74.612 100.012 125.412 150.812 176.212 201.612 227.012 252.412 277.812 3/4 0.7500 806.450 831.850 857.250 882.650 908.050 933.450 958.850 984.250 1009.650 1035.050
61/64 0.953125 24.209 49.609 75.009 100.409 125.809 151.209 176.609 202.009 227.409 252.809 278.209 13/16 0.8125 808.038 833.438 858.838 884.238 909.638 935.038 960.438 985.838 1011.238 1036.638
31/32 0.968750 24.606 50.006 75.406 100.806 126.206 151.606 177.006 202.406 227.806 253.206 278.606 7/8 0.8750 809.625 835.025 860.425 885.825 911.225 936.625 962.025 987.425 1012.825 1038.225
63/64 0.984375 25.003 50.403 75.803 101.203 126.603 152.003 177.403 202.803 228.203 253.603 279.003 15/16 0.9375 811.212 836.612 862.012 887.412 912.812 938.212 963.621 989.012 1014.412 1039.812
C 14 C 15
C001-034E.indd 14-15 11/20/13 5:03:56 PM

APPENDICES
Appendix Table 7 Hardness Conversion Table (Reference) Appendix Table 8 Physical and Mechanical Properties of Materials
Rockwell Brinell Hardness Rockwell Hardness Youngs

C Scale Hardness A Scale B Scale Coefficient of Hardness modulus Tensile Strength Yield Point Elongation
Vickers Materials Specific Gravity Linear Expansion (Brinell) (MPa) (MPa) (MPa) (%)
Tungsten Load588.4N Load980.7N Shore Hardness
Hardness Standard Ball {60kgf} {100kgf} (0 to 100C) {kgf/mm2} {kgf/mm2} {kgf/mm2}
(1 471N) Carbide Ball
Brale Indenter 1.588 mmBall (K1)
{150kgf} (1/16in)
208 000 1 570 to 1 960
68 940 85.6 97 Bearing Steel (hardened) 7.83 12.5106 650 to 740
67 900 85.0 95 {21 200} {160 to 200}
66 865 84.5 92
65 832 739 83.9 91
64 800 722 83.4 88
Martensitic Stainless Steel 200 000 1 960 1 860
63 772 705 82.8 87 SUS 440C 7.68 10.1106 580 {20 400} {200} {190}
62 746 688 82.3 85
61 720 670 81.8 83
60 697 654 81.2 81
59 674 634 80.7 80
206 000 373 to 471 216 to 294
Mild Steel (C=0.12~0.20%) 7.86 11.6106 100 to 130 24 to 36
58 653 615 80.1 78 {21 000} {38 to 48} {22 to 30}
57 633 595 79.6 76
56 613 577 79.0 75
55 595 560 78.5 74
54 577 543 78.0 72 206 000 539 to 686 333 to 451
Hard Steel (C=0.3~0.5%) 7.84 11.3106 160 to 200 14 to 26
{21 000} {55 to 70} {34 to 46}
53 560 525 77.4 71
52 544 500 512 76.8 69
51 528 487 496 76.3 68
50 513 475 481 75.9 67 Austenitic Stainless Steel 193 000 588 245
49 498 464 469 75.2 66 8.03 16.3106 150 60
SUS 304 {19 700} {60} {25}
48 484 451 455 74.7 64
47 471 442 443 74.1 63
46 458 432 432 73.6 62
45 446 421 421 73.1 60 More than
Gray Iron
44 434 409 409 72.5 58 7.3 10.4106 223 200
FC200 {20}
43 423 400 400 72.0 57 Cast Iron 98 100
42 412 390 390 71.5 56 {10 000}
41 402 381 381 70.9 55 More than
40 392 371 371 70.4 54 Spheroidal graphite Iron 7.0 11.7106
Less than 400 More than
39 382 362 362 69.9 52 FCD400 201 {41} 12
38 372 353 353 69.4 51
37 363 344 344 68.9 50
36 354 336 336 68.4 (109.0) 49 70 600 78 34
Aluminum 2.69 23.7106 15 to 26 35
35 345 327 327 67.9 (108.5) 48 {7 200} {8} {3.5}
34 336 319 319 67.4 (108.0) 47
33 327 311 311 66.8 (107.5) 46
32 318 301 301 66.3 (107.0) 44 92 200 147
Zinc 7.14 31106 30 to 60 30 to 40
31 310 294 294 65.8 (106.0) 43 {9 400} {15}
30 302 286 286 65.3 (105.5) 42
29 294 279 279 64.7 (104.5) 41
28 286 271 271 64.3 (104.0) 41 123 000 196 69
Copper 8.93 16.2106 50 15 to 20
27 279 264 264 63.8 (103.0) 40 {12 500} {20} {7}
26 272 258 258 63.3 (102.5) 38
25 266 253 253 62.8 (101.5) 38
24 260 247 247 62.4 (101.0) 37
(Annealed) 45 294 to 343 65 to 75
23 254 243 243 62.0 100.0 36 {30 to 35}
22 248 237 237 61.5 99.0 35 6 103 000
21 243 231 231 61.0 98.5 35 Brass 8.5 19.110 {10 500}
20 238 226 226 60.5 97.8 34 (Machined) 85 to 130 363 to 539 15 to 50
{37 to 55}
(18) 230 219 219 96.7 33
(16) 222 212 212 95.5 32
(14) 213 203 203 93.9 31 Remarks The hardness of hardened bearing steel and martensitic stainless steel is usually expressed using the Rockwell C Scale,
(12) 204 194 194 92.3 29 but for comparison, it is converted into Brinell hardness.
(10) 196 187 187 90.7 28
(8) 188 179 179 89.5 27
(6) 180 171 171 87.1 26
(4) 173 165 165 85.5 25
(2) 166 158 158 83.5 24
(0) 160 152 152 81.7 24
C 16 C 17
C001-034E.indd 16-17 11/20/13 5:03:57 PM

APPENDICES
Appendix Table 9 Tolerances for Shaft Diameters

Units : m
Diameter Single Plane Diameter Classification
Classification (mm) Mean B.D. (mm)
Deviation d6 e6 f6 g5 g6 h5 h6 h7 h8 h9 h10 js5 js6 j5 j6 j7 k5 k6 k7 m5 m6 n6 p6 r6 r7
(Normal)
over incl. & dmp over incl.
3 6 0 30 20 10 4 4 0 0 0 0 0 0 2.5 4.0 + 3 + 6 + 8 + 6 + 9 + 13 + 9 + 12 + 16 + 20 + 23 + 27 3 6
8 38 28 18 9 12 5 8 12 18 30 48 2 2 4 + 1 + 1 + 1 + 4 + 4 + 8 + 12 + 15 + 15
0 40 25 13 5 5 0 0 0 0 0 0
3.0 4.5 + 4 + 7 + 10 + 7 + 10 + 16 + 12 + 15 + 19 + 24 + 28 + 34
6 10 8 49 34 22 11 14 6 9 15 22 36 58 2 2 5 + 1 + 1 + 1 + 6 + 6 + 10 + 15 + 19 + 19 6 10
10 18 0 50 32 16 6 6 0 0 0 0 0 0 4.0 5.5 + 5 + 8 + 12 + 9 + 12 + 19 + 15 + 18 + 23 + 29 + 34 + 41
8 61 43 27 14 17 8 11 18 27 43 70 10 18
3 3 6 + 1 + 1 + 1 + 7 + 7 + 12 + 18 + 23 + 23
0 65 40 20 7 7 0 0 0 0 0 0 + 5 + 9 + 13 + 11 + 15 + 23 + 17 + 21 + 28 + 35 + 41 + 49
18 30
10 78 53 33 16 20 9 13 21 33 52 84 4.5 6.5 4 4 8 + 2 + 2 + 2 + 8 + 8 + 15 + 22 + 28 + 28 18 30
0 80 50 25 9 9 0 0 0 0 0 0
5.5 8.0 + 6 + 11 + 15 + 13 + 18 + 27 + 20 + 25 + 33 + 42 + 50 + 59
30 50 12 96 66 41 20 25 11 16 25 39 62 100 5 5 10 + 2 + 2 + 2 + 9 + 9 + 17 + 26 + 34 + 34 30 50
+ 60 + 71
0 100 60 30 10 10 0 0 0 0 0 0 + 6 + 12 + 18 + 15 + 21 + 32 + 24 + 30 + 39 + 51 + 41 + 41 50 65
50 80 15 119 79 49 23 29 13 19 30 46 74 120 6.5 9.5 7 7 12 + 2 + 2 + 2 + 11 + 11 + 20 + 32 + 62 + 73
+ 43 + 43 65 80
+ 73 + 86
80 100
80 120 0 120 72 36 12 12 0 0 0 0 0 0
7.5 11.0 + 6 + 13 + 20 + 18 + 25 + 38 + 28 + 35 + 45 + 59 + 51 + 51
20 142 94 58 27 34 15 22 35 54 87 140 9 9 15 + 3 + 3 + 3 + 13 + 13 + 23 + 37 + 76 + 89
+ 54 + 54 100 120
+ 88 + 103
120 140
+ 63 + 63
120 180 0 145 85 43 14 14 0 0 0 0 0 0
9.0 12.5 + 7 + 14 + 22 + 21 + 28 + 43 + 33 + 40 + 52 + 68 + 90 + 105 140 160
25 170 110 68 32 39 18 25 40 63 100 160 11 11 18 + 3 + 3 + 3 + 15 + 15 + 27 + 43 + 65 + 65
+ 93 + 108
160 180
+ 68 + 68
+ 106 + 123 180 200
+ 77 + 77
0 170 100 50 15 15 0 0 0 0 0 0
10.0 14.5 + 7 + 16 + 25 + 24 + 33 + 50 + 37 + 46 + 60 + 79 + 109 + 126
180 250 30 199 129 79 35 44 20 29 46 72 115 185 13 13 21 + 4 + 4 + 4 + 17 + 17 + 31 + 50 + 80 + 80 200 225
+ 113 + 130
225 250
+ 84 + 84
+ 126 + 146 250 280
250 315 0 190 110 56 17 17 0 0 0 0 0 0
11.5 16.0 + 7 16 26 + 27 + 36 + 56 + 43 + 52 + 66 + 88 + 94 + 94
35 222 142 88 40 49 23 32 52 81 130 210 16 + 4 + 4 + 4 + 20 + 20 + 34 + 56 + 130 + 150
+ 98 + 98 280 315
+ 144 + 165
315 355
315 400 0 210 125 62 18 18 0 0 0 0 0 0
12.5 18.0 + 7 18 + 29 + 29 + 40 + 61 + 46 + 57 + 73 + 98 + 108 + 108
40 246 161 98 43 54 25 36 57 89 140 230 18 28 + 4 + 4 + 4 + 21 + 21 + 37 + 62 + 150 + 171
+ 114 + 114 355 400
+ 166 + 189 400 450
400 500 0 230 135 68 20 20 0 0 0 0 0 0
13.5 20.0
+ 7
20
+ 31 + 32 + 45 + 68 + 50 + 63 + 80 + 108 + 126 + 126
45 270 175 108 47 60 27 40 63 97 155 250 20 32 + 5 + 5 + 5 + 23 + 23 + 40 + 68 + 172 + 195
+ 132 + 132 450 500
+ 194 + 220 500 560
500 630 0 260 145 76 22 0 0 0 0 0 22.0 + 44 + 70 + 70 + 88 + 122 + 150 + 150
50 304 189 120 66 44 70 110 175 280 0 0 + 26 + 44 + 78 + 199 + 225 560 630
+ 155 + 155
+ 225 + 255
0 290 160 80 24 0 0 0 0 0 630 710
630 800 25.0 + 50 + 80 + 80 + 100 + 138 + 175 + 175
75 340 210 130 74 50 80 125 200 320 0 0 + 30 + 50 + 88 + 235 + 265
+ 185 + 185 710 800
+ 266 + 300
0 320 170 86 26 0 0 0 0 0 800 900
800 1 000 28.0 + 56 + 90 + 90 + 112 + 156 + 210 + 210
100 376 226 142 82 56 90 140 230 360 0 0 + 34 + 56 + 100 + 276 + 310 900 1 000
+ 220 + 220
+ 316 + 355 1 000 1 120
1 000 1 250 0 350 195 98 28 0 0 0 0 0 33.0 + 66 + 105 + 106 + 132 + 186 + 250 + 250
125 416 261 164 94 66 105 165 260 420 0 0 + 40 + 66 + 120 + 326 + 365 1 120 1 250
+ 260 + 260
+ 378 + 425 1 250 1 400
1 250 1 600 0 390 220 110 30 0 0 0 0 0 39.0 + 78 + 125 + 126 + 156 + 218 + 300 + 300
160 468 298 188 108 78 125 195 310 500 0 0 + 48 + 78 + 140 + 408 + 455
+ 330 + 330 1 400 1 600
+ 462 + 520 1 600 1 800
1 600 2 000 0 430 240 120 32 0 0 0 0 0 46.0 + 92 + 150 + 150 + 184 + 262 + 370 + 370
200 522 332 212 124 92 150 230 370 600 0 0 + 58 + 92 + 170 + 492 + 550 1 800 2 000
+ 400 + 400
C 18 C 19
C001-034E.indd 18-19 11/20/13 5:03:57 PM

APPENDICES
Appendix Table 10 Tolerances for Housing Bore Diameters

Units : m
Diameter Single Plane Diameter Classification
Classification (mm) Mean O.D. (mm)
Deviation E6 F6 F7 G6 G7 H6 H7 H8 J6 J7 JS6 JS7 K5 K6 K7 M5 M6 M7 N5 N6 N7 P6 P7
(Normal)
over incl. & Dmp over incl.
0 + 43 + 27 + 34 + 17 + 24 + 11 + 18 + 27 + 6 + 10 + 2 + 2 + 6 4 4 0 9 9 5 15 11
10 18 5.5 9 10 18
8 + 32 + 16 + 16 + 6 + 6 0 0 0 5 8 6 9 12 12 15 18 17 20 23 26 29
0 + 53 + 33 + 41 + 20 + 28 + 13 + 21 + 33 + 8 + 12 + 1 + 2 + 6 5 4 0 12 11 7 18 14
18 30 6.5 10.5 18 30
9 + 40 + 20 + 20 + 7 + 7 0 0 0 5 9 8 11 15 14 17 21 21 24 28 31 35
0 + 66 + 41 + 50 + 25 + 34 + 16 + 25 + 39 + 10 + 14 + 2 + 3 + 7 5 4 0 13 12 8 21 17
30 50 8 12.5 30 50
11 + 50 + 25 + 25 + 9 + 9 0 0 0 6 11 9 13 18 16 20 25 24 28 33 37 42
0 + 79 + 49 + 60 + 29 + 40 + 19 + 30 + 46 + 13 + 18 + 3 + 4 + 9 6 5 0 15 14 9 26 21
50 80 9.5 15 50 80
13 + 60 + 30 + 30 + 10 + 10 0 0 0 6 12 10 15 21 19 24 30 28 33 39 45 51
0 + 94 + 58 + 71 + 34 + 47 + 22 + 35 + 54 + 16 + 22 + 2 + 4 + 10 8 6 0 18 16 10 30 24
80 120 11 17.5 80 120
15 + 72 + 36 + 36 + 12 + 12 0 0 0 6 13 13 18 25 23 28 35 33 38 45 52 59
0
120 150 18 + 110 + 68 + 83 + 39 + 54 + 25 + 40 + 63 + 18 + 26 + 3 + 4 + 12 9 8 0 21 20 12 36 28
12.5 20 120 180
150 180 0 + 85 + 43 + 43 + 14 + 14 0 0 0 7 14 15 21 28 27 33 40 39 45 52 61 68
25
0 + 129 + 79 + 96 + 44 + 61 + 29 + 46 + 72 + 22 + 30 + 2 + 5 + 13 11 8 0 25 22 14 41 33
180 250 14.5 23 180 250
30 + 100 + 50 + 50 + 15 + 15 0 0 0 7 16 18 24 33 31 37 46 45 51 60 70 79
0 + 142 + 88 + 108 + 49 + 69 + 32 + 52 + 81 + 25 + 36 + 3 + 5 + 16 13 9 0 27 25 14 47 36
250 315 16 26 250 315
35 + 110 + 56 + 56 + 17 + 17 0 0 0 7 16 20 27 36 36 41 52 50 57 66 79 88
0 + 161 + 98 + 119 + 54 + 75 + 36 + 57 + 89 + 29 + 39 + 3 + 7 + 17 14 10 0 30 26 16 51 41
315 400 18 28.5 315 400
40 + 125 + 62 + 62 + 18 + 18 0 0 0 7 18 22 29 40 39 46 57 55 62 73 87 98
0 + 175 + 108 + 131 + 60 + 83 + 40 + 63 + 97 + 33 + 43 + 2 + 8 + 18 16 10 0 33 27 17 55 45

400 500 20 31.5 400 500
45 + 135 + 68 + 68 + 20 + 20 0 0 0 7 20 25 32 45 43 50 63 60 67 80 95 108
0 + 189 + 120 + 146 + 66 + 92 + 44 + 70 + 110 0 0 26 26 44 44 78 78

500 630 22 35 500 630
50 + 145 + 76 + 76 + 22 + 22 0 0 0 44 70 70 96 88 114 122 148
0 + 210 + 130 + 160 + 74 + 104 + 50 + 80 + 125 0 0 30 30 50 50 88 88

630 800 25 40 630 800
75 + 160 + 80 + 80 + 24 + 24 0 0 0 50 80 80 110 100 130 138 168
0 + 226 + 142 + 176 + 82 + 116 + 56 + 90 + 140 0 0 34 34 56 56 100 100

800 1 000 28 45 800 1 000
100 + 170 + 86 + 86 + 26 + 26 0 0 0 56 90 90 124 112 146 156 190
0 + 261 + 164 + 203 + 94 + 133 + 66 + 105 + 165 0 0 40 40 66 66 120 120

1 000 1 250 33 52.5 1 000 1 250
125 + 195 + 98 + 98 + 28 + 28 0 0 0 66 105 106 145 132 171 186 225
0 + 298 + 188 + 235 + 108 + 155 + 78 + 125 + 195 0 0 48 48 78 78 140 140

1 250 1 600 39 62.5 1 250 1 600
160 + 220 + 110 + 110 + 30 + 30 0 0 0 78 125 126 173 156 203 218 265
0 + 332 + 212 + 270 + 124 + 182 + 92 + 150 + 230 0 0 58 58 92 92 170 170

1 600 2 000 46 75 1 600 2 000
200 + 240 + 120 + 120 + 32 + 32 0 0 0 92 150 150 208 184 242 262 320
0 + 370 + 240 + 305 + 144 + 209 + 110 + 175 + 280 0 0 68 68 110 110 195 195
2 000 2 500 55 87.5 2 000 2 500
250 + 260 + 130 + 130 + 34 + 34 0 0 0 110 175 178 243 220 285 305 370
C 20 C 21
C001-034E.indd 20-21 11/20/13 5:03:59 PM

APPENDICES
Appendix Table 11 Values of Standard Tolerance Grades IT
Basic Size Standard Grades

Basic Size
(mm) IT1 IT2 IT3 IT4 IT5 IT6 IT7 IT8 IT9 IT10 IT11 (mm)
IT12 IT13 IT14 IT15 IT16 IT17 IT18
over incl. Tolerances ( m) Tolerances (mm) over incl.
3 0.8 1.2 2 3 4 6 10 14 25 40 60 0.10 0.14 0.25 0.40 0.60 1.00 1.40 3
3 6 1 1.5 2.5 4 5 8 12 18 30 48 75 0.12 0.18 0.30 0.48 0.75 1.20 1.80 3 6
6 10 1 1.5 2.5 4 6 9 15 22 36 58 90 0.15 0.22 0.36 0.58 0.90 1.50 2.20 6 10
10 18 1.2 2 3 5 8 11 18 27 43 70 110 0.18 0.27 0.43 0.70 1.10 1.80 2.70 10 18
18 30 1.5 2.5 4 6 9 13 21 33 52 84 130 0.21 0.33 0.52 0.84 1.30 2.10 3.30 18 30
30 50 1.5 2.5 4 7 11 16 25 39 62 100 160 0.25 0.39 0.62 1.00 1.60 2.50 3.90 30 50
50 80 2 3 5 8 13 19 30 46 74 120 190 0.30 0.46 0.74 1.20 1.90 3.00 4.60 50 80
80 120 2.5 4 6 10 15 22 35 54 87 140 220 0.35 0.54 0.87 1.40 2.20 3.50 5.40 80 120
120 180 3.5 5 8 12 18 25 40 63 100 160 250 0.40 0.63 1.00 1.60 2.50 4.00 6.30 120 180
180 250 4.5 7 10 14 20 29 46 72 115 185 290 0.46 0.72 1.15 1.85 2.90 4.60 7.20 180 250
250 315 6 8 12 16 23 32 52 81 130 210 320 0.52 0.81 1.30 2.10 3.20 5.20 8.10 250 315
315 400 7 9 13 18 25 36 57 89 140 230 360 0.57 0.89 1.40 2.30 3.60 5.70 8.90 315 400
400 500 8 10 15 20 27 40 63 97 155 250 400 0.63 0.97 1.55 2.50 4.00 6.30 9.70 400 500
500 630 9 11 16 22 32 44 70 110 175 280 440 0.70 1.10 1.75 2.80 4.40 7.00 11.00 500 630
630 800 10 13 18 25 36 50 80 125 200 320 500 0.80 1.25 2.00 3.20 5.00 8.00 12.50 630 800
800 1 000 11 15 21 28 40 56 90 140 230 360 560 0.90 1.40 2.30 3.60 5.60 9.00 14.00 800 1 000
1 000 1 250 13 18 24 33 47 66 105 165 260 420 660 1.05 1.65 2.60 4.20 6.60 10.50 16.50 1 000 1 250
1 250 1 600 15 21 29 39 55 78 125 195 310 500 780 1.25 1.95 3.10 5.00 7.80 12.50 19.50 1 250 1 600
1 600 2 000 18 25 35 46 65 92 150 230 370 600 920 1.50 2.30 3.70 6.00 9.20 15.00 23.00 1 600 2 000
2 000 2 500 22 30 41 55 78 110 175 280 440 700 1 100 1.75 2.80 4.40 7.00 11.00 17.50 28.00 2 000 2 500
2 500 3 150 26 36 50 68 96 135 210 330 540 860 1 350 2.10 3.30 5.40 8.60 13.50 21.00 33.00 2 500 3 150
Remarks 1. Standard tolerance grades IT14 to IT18 shall not be used for basic sizes less than or equal to 1 mm.
2. Values for standard tolerance grades IT1 to IT5 for basic sizes over 500 mm are included for experimental use.
C 22 C 23
C001-034E.indd 22-23 11/20/13 5:04:00 PM

APPENDICES
Appedix Table 12 Speed Factor fn Appendix Table 13 Fatigue Life Factor fn and Fatigue Life L L h
Ball Bearings f n = (0.03 n ) 1/3
Ball Bearings L=(C / P) 3 L h =500 f h 3
Roller Bearings f n = (0.03 n ) 3/10
Roller Bearings L=(C / P) 10/3
L h =500 f h 10/3
Ball Bearing Life Roller Bearing Life Ball Bearing Life Roller Bearing Life
Speed Factor f n Speed Factor f n Speed Factor f n
Speed Speed Speed
C/P or fh L Lh L Lh C/P or fh L Lh L Lh
n (min 1) Ball Bearings Roller Bearings n (min 1) Ball Bearings Roller Bearings n (min 1) Ball Bearings Roller Bearings
(106 rev) (h) (106 rev) (h) (106 rev) (h) (106 rev) (h)
10 1.49 1.44 180 0.570 0.603 3 000 0.223 0.259 0.70 0.34 172 0.30 152 3.45 41.1 20 500 62.0 31 000
11 1.45 1.39 190 0.560 0.593 3 200 0.218 0.254 0.75 0.42 211 0.38 192 3.50 42.9 21 400 65.1 32 500
12 1.41 1.36 200 0.550 0.584 3 400 0.214 0.250 0.80 0.51 256 0.48 238 3.55 44.7 22 400 68.2 34 100
13 1.37 1.33 220 0.533 0.568 3 600 0.210 0.245 0.85 0.61 307 0.58 291 3.60 46.7 23 300 71.5 35 800
14 1.34 1.30 240 0.518 0.553 3 800 0.206 0.242 0.90 0.73 365 0.70 352 3.65 48.6 24 300 74.9 37 400
15 1.30 1.27 260 0.504 0.540 4 000 0.203 0.238 0.95 0.86 429 0.84 421 3.70 50.7 25 300 78.3 39 200
16 1.28 1.25 280 0.492 0.528 4 200 0.199 0.234 1.00 1.00 500 1.00 500 3.75 52.7 26 400 81.9 41 000
17 1.25 1.22 300 0.481 0.517 4 400 0.196 0.231 1.05 1.16 579 1.18 588 3.80 54.9 27 400 85.6 42 800
18 1.23 1.20 320 0.471 0.507 4 600 0.194 0.228 1.10 1.33 665 1.37 687 3.85 57.1 28 500 89.4 44 700
19 1.21 1.18 340 0.461 0.498 4 800 0.191 0.225 1.15 1.52 760 1.59 797 3.90 59.3 29 700 93.4 46 700
1.20 1.73 864 1.84 918 3.95 61.6 30 800 97.4 48 700
20 1.19 1.17 360 0.452 0.490 5 000 0.188 0.222 1.25 1.95 977 2.10 1 050 4.00 64.0 32 000 102 50 800
21 1.17 1.15 380 0.444 0.482 5 200 0.186 0.220 1.30 2.20 1 100 2.40 1 200 4.05 66.4 33 200 106 52 900
22 1.15 1.13 400 0.437 0.475 5 400 0.183 0.217 1.35 2.46 1 230 2.72 1 360 4.10 68.9 34 500 110 55 200
23 1.13 1.12 420 0.430 0.468 5 600 0.181 0.215 1.40 2.74 1 370 3.07 1 530 4.15 71.5 35 700 115 57 400
24 1.12 1.10 440 0.423 0.461 5 800 0.179 0.213
1.45 3.05 1 520 3.45 1 730 4.20 74.1 37 000 120 59 800
1.50 3.38 1 690 3.86 1 930 4.25 76.8 38 400 124 62 200
25 1.10 1.09 460 0.417 0.455 6 000 0.177 0.211 1.55 3.72 1 860 4.31 2 150 4.30 79.5 39 800 129 64 600
26 1.09 1.08 480 0.411 0.449 6 200 0.175 0.209 1.60 4.10 2 050 4.79 2 400 4.35 82.3 41 200 134 67 200
27 1.07 1.07 500 0.405 0.444 6 400 0.173 0.207 1.65 4.49 2 250 5.31 2 650 4.40 85.2 42 600 140 69 800
28 1.06 1.05 550 0.393 0.431 6 600 0.172 0.205
29 1.05 1.04 600 0.382 0.420 6 800 0.170 0.203
1.70 4.91 2 460 5.86 2 930 4.45 88.1 44 100 145 72 500
1.75 5.36 2 680 6.46 3 230 4.50 91.1 45 600 150 75 200
30 1.04 1.03 650 0.372 0.410 7 000 0.168 0.201 1.80 5.83 2 920 7.09 3 550 4.55 94.2 47 100 156 78 000
31 1.02 1.02 700 0.362 0.401 7 200 0.167 0.199 1.85 6.33 3 170 7.77 3 890 4.60 97.3 48 700 162 80 900
32 1.01 1.01 750 0.354 0.393 7 400 0.165 0.198 1.90 6.86 3 430 8.50 4 250 4.65 101 50 300 168 83 900
33.3 1.00 1.00 800 0.347 0.385 7 600 0.164 0.196
34 0.993 0.994 850 0.340 0.378 7 800 0.162 0.195 1.95 7.41 3 710 9.26 4 630 4.70 104 51 900 174 87 000
2.00 8.00 4 000 10.1 5 040 4.75 107 53 600 180 90 100
2.05 8.62 4 310 10.9 5 470 4.80 111 55 300 187 93 300
36 0.975 0.977 900 0.333 0.372 8 000 0.161 0.193 2.10 9.26 4 630 11.9 5 930 4.85 114 57 000 193 96 600
38 0.957 0.961 950 0.327 0.366 8 500 0.158 0.190 2.15 9.94 4 970 12.8 6 410 4.90 118 58 800 200 99 900
40 0.941 0.947 1 000 0.322 0.360 9 000 0.155 0.186
42 0.926 0.933 1 050 0.317 0.355 9 500 0.152 0.183 2.20 10.6 5 320 13.8 6 920 4.95 121 60 600 207 103 000
44 0.912 0.920 1 100 0.312 0.350 10 000 0.149 0.181 2.25 11.4 5 700 14.9 7 460 5.00 125 62 500 214 107 000
2.30 12.2 6 080 16.1 8 030 5.10 133 66 300 228 114 000
46 0.898 0.908 1 150 0.307 0.346 11 000 0.145 0.176 2.35 13.0 6 490 17.3 8 630 5.20 141 70 300 244 122 000
48 0.886 0.896 1 200 0.303 0.341 12 000 0.141 0.171 2.40 13.8 6 910 18.5 9 250 5.30 149 74 400 260 130 000
50 0.874 0.885 1 250 0.299 0.337 13 000 0.137 0.167
55 0.846 0.861 1 300 0.295 0.333 14 000 0.134 0.163 2.45 14.7 7 350 19.8 9 910 5.40 157 78 700 276 138 000
60 0.822 0.838 1 400 0.288 0.326 15 000 0.130 0.160 2.50 15.6 7 810 21.2 10 600 5.50 166 83 200 294 147 000
2.55 16.6 8 290 22.7 11 300 5.60 176 87 800 312 156 000
2.60 17.6 8 790 24.2 12 100 5.70 185 92 600 331 165 000
65 0.800 0.818 1 500 0.281 0.319 16 000 0.128 0.157 2.65 18.6 9 300 25.8 12 900 5.80 195 97 600 351 175 000
70 0.781 0.800 1 600 0.275 0.313 17 000 0.125 0.154
75 0.763 0.784 1 700 0.270 0.307 18 000 0.123 0.151 2.70 19.7 9 840 27.4 13 700 5.90 205 103 000 371 186 000
80 0.747 0.769 1 800 0.265 0.302 19 000 0.121 0.149 2.75 20.8 10 400 29.1 14 600 6.00 216 108 000 392 196 000
85 0.732 0.755 1 900 0.260 0.297 20 000 0.119 0.147 2.80 22.0 11 000 30.9 15 500 6.50 275 137 000 513 256 000
2.85 23.1 11 600 32.8 16 400 7.00 343 172 000 656 328 000
2.90 24.4 12 200 34.8 17 400 7.50 422 211 000 826 413 000
90 0.718 0.742 2 000 0.255 0.293 22 000 0.115 0.143
95 0.705 0.730 2 100 0.251 0.289 24 000 0.112 0.139 2.95 25.7 12 800 36.8 18 400 8.00 512 256 000 1 020 512 000
100 0.693 0.719 2 200 0.247 0.285 26 000 0.109 0.136 3.00 27.0 13 500 38.9 19 500 8.50 614 307 000 1 250 627 000
110 0.672 0.699 2 300 0.244 0.281 28 000 0.106 0.133 3.05 28.4 14 200 41.1 20 600 9.00 729 365 000 1 520 758 000
120 0.652 0.681 2 400 0.240 0.277 30 000 0.104 0.130 3.10 29.8 14 900 43.4 21 700 9.50 857 429 000 1 820 908 000
3.15 31.3 15 600 45.8 22 900 10.0 1 000 2 150
130 0.635 0.665 2 500 0.237 0.274 32 000 0.101 0.127
140 0.620 0.650 2 600 0.234 0.271 34 000 0.099 0.125 3.20 32.8 16 400 48.3 24 100 11.0 1 330 2 960
150 0.606 0.637 2 700 0.231 0.268 36 000 0.097 0.123 3.25 34.3 17 200 50.8 25 400 12.0 1 730 3 960
160 0.593 0.625 2 800 0.228 0.265 38 000 0.096 0.121 3.30 35.9 18 000 53.5 26 800 13.0 2 200 5 170
170 0.581 0.613 2 900 0.226 0.262 40 000 0.094 0.119 3.35 37.6 18 800 56.3 28 100 14.0 2 740 6 610
3.40 39.3 19 700 59.1 29 600 15.0 3 380 8 320
C 24 C 25
C001-034E.indd 24-25 11/20/13 5:04:00 PM

APPENDICES
Appendix Table14 Index of Inch Design Tapered Roller Bearings
Nominal Dimension (mm) Nominal Dimension (mm) Nominal Dimension (mm) Nominal Dimension (mm)
Bearing No. Bearing No. Bearing No. Bearing No.
d :CONE (Bore Dia.) Pages d :CONE (Bore Dia.) Pages d :CONE (Bore Dia.) Pages d :CONE (Bore Dia.) Pages
CONE, CUP D:CUP (Outside Dia.) CONE, CUP D:CUP (Outside Dia.) CONE, CUP D:CUP (Outside Dia.) CONE, CUP D:CUP (Outside Dia.)
332 D 80.000 B140,B144,B146 497 d 85.725 B162 657 d 73.025 B158 1328 D 52.388 B136
336 d 41.275 B146 498 d 84.138 B162 658 d 74.612 B158 1329 D 53.975 B136
342 d 41.275 B146 522 D 101.600 B148,B150 659 d 76.200 B158 1380 d 22.225 B136
342 S d 42.875 B146 528 d 47.625 B148 661 d 79.375 B160 1620 D 66.675 B142
344 d 40.000 B144 529 d 50.800 B150 663 d 82.550 B160 1680 d 33.338 B142
344 A d 40.000 B144 529 X d 50.800 B150 664 d 84.138 B162 1729 D 56.896 B136,B138
346 d 31.750 B140 532 X D 107.950 B152 665 d 85.725 B162 1755 d 22.225 B136
354 A D 85.000 B148 539 d 53.975 B152 665 A d 85.725 B162 1779 d 23.812 B138
359 S d 46.038 B148 552 A D 123.825 B152,B154,B156 672 D 168.275 B162,B164,B166 1922 D 57.150 B138
362 A D 88.900 B148,B150 553 X D 122.238 B154,B156 677 d 85.725 B162 1988 d 28.575 B138
366 d 50.000 B150 555 S d 57.150 B152 681 d 92.075 B164 1997 X d 26.988 B138
368 d 50.800 B150 557 S d 53.975 B152 683 d 95.250 B164 A2047 d 12.000 B136
368 A d 50.800 B150 558 d 60.325 B154 685 d 98.425 B164 A2126 D 31.991 B136
369 A d 47.625 B148 559 d 63.500 B154 687 d 101.600 B166 2523 D 69.850 B140,B142
372 D 100.000 B150 560 d 66.675 B156 742 D 150.089 B156,B160,B162 2558 d 30.162 B140
374 D 93.264 B148 560 S d 68.262 B156 743 D 150.000 B160 2559 d 30.162 B140
376 d 45.000 B148 563 D 127.000 B154,B156,B158 745 A d 69.850 B156 2580 d 31.750 B140
377 d 52.388 B150 563 X D 127.000 B156 749 d 85.026 B162 2582 d 31.750 B140
382 D 98.425 B152 565 d 63.500 B154 749 A d 82.550 B160 2585 d 33.338 B142
382 A D 96.838 B152 566 d 69.850 B156 749 S d 85.026 B162 2631 D 66.421 B140
382 S D 96.838 B152 567 d 73.025 B158 750 d 79.375 B160 2690 d 29.367 B140
385 d 55.000 B152 567 A d 71.438 B158 752 D 161.925 B160,B162 2720 D 76.200 B144
387 d 57.150 B152 567 S d 71.438 B158 753 D 168.275 B160,B162 2729 D 76.200 B144
387 A d 57.150 B152 568 d 73.817 B158 757 d 82.550 B160 2735 X D 73.025 B144
388 A d 57.531 B152 569 d 64.963 B154 758 d 85.725 B162 2788 d 38.100 B144
390 A d 63.500 B154 570 d 68.262 B156 759 d 88.900 B162 2789 d 39.688 B144
394 A D 110.000 B154,B156 572 D 139.992 B158,B160 760 d 90.488 B162 2820 D 73.025 B142
395 d 63.500 B154 572 X D 139.700 B160 766 d 88.900 B162 2877 d 34.925 B142
395 A d 66.675 B156 575 d 76.200 B158 772 D 180.975 B164,B166 2924 D 85.000 B148
395 S d 66.675 B156 580 d 82.550 B160 776 d 95.250 B164 2984 d 46.038 B148
397 d 60.000 B154 581 d 80.962 B160 779 d 98.425 B164 3120 D 72.626 B140,B142
399 A d 68.262 B156 582 d 82.550 B160 780 d 101.600 B166 3188 d 31.750 B140
414 D 88.501 B144 590 A d 76.200 B158 782 d 104.775 B166 3197 d 33.338 B142
418 d 38.100 B144 592 D 152.400 B164 787 d 104.775 B166 3320 D 80.167 B144
432 D 95.250 B146 592 A D 152.400 B158,B162,B164 792 D 206.375 B168 3386 d 39.688 B144
432 A D 95.250 B148 593 d 88.900 B162 795 d 120.650 B168 3420 D 79.375 B142,B144
436 d 46.038 B148 594 d 95.250 B164 797 d 130.000 B168 3478 d 34.925 B142
438 d 44.450 B146 596 d 85.725 B162 799 d 128.588 B168 3479 d 36.512 B144
453 A D 107.950 B148 597 d 93.662 B164 799 A d 130.175 B168 3490 d 38.100 B144
453 X D 104.775 B152 598 d 92.075 B164 832 D 168.275 B160,B162 3525 D 87.312 B146
460 d 44.450 B148 598 A d 92.075 B164 837 d 76.200 B160 3576 d 41.275 B146
462 d 57.150 B152 614 X D 115.000 B152 842 d 82.550 B160 3578 d 44.450 B146
469 d 57.150 B152 622 X d 55.000 B152 843 d 76.200 B160 3720 D 93.264 B146
472 D 120.000 B156,B158 632 D 136.525 B154,B158 850 d 88.900 B162 3730 D 93.264 B150
472 A D 120.000 B156 633 D 130.175 B154,B156,B158 854 D 190.500 B162,B164,B166 3775 d 50.800 B150
478 d 65.000 B156 637 d 60.325 B154 855 d 88.900 B162 3780 d 50.800 B150
480 d 68.262 B156 639 d 63.500 B154 857 d 92.075 B164 3782 d 44.450 B146
484 d 70.000 B158 643 d 69.850 B156 861 d 101.600 B166 3820 D 85.725 B146
492 A D 133.350 B160,B162 644 d 71.438 B158 864 d 95.250 B164 3877 d 41.275 B146
493 D 136.525 B158,B160,B162 645 d 71.438 B158 866 d 98.425 B164 3920 D 112.712 B154,B156
495 d 82.550 B160 652 D 152.400 B158,B160 932 D 212.725 B166 3926 D 112.712 B152,B154
495 A d 76.200 B158 653 D 146.050 B156,B158,B160,B162 938 d 114.300 B166 3981 d 58.738 B152
495 AX d 76.200 B158 653 X D 150.000 B158 1220 D 57.150 B136 3982 d 63.500 B154
496 d 80.962 B160 655 d 69.850 B156 1280 d 22.225 B136 3984 d 66.675 B156
C 26 C 27
C001-034E.indd 26-27 11/20/13 5:04:01 PM

APPENDICES
3994 d 66.675 B156 02820 D 73.025 B138,B142 13685 d 38.100 B144 19150 d 38.100 B144
A4050 d 12.700 B136 02872 d 28.575 B138 13687 d 38.100 B144 19268 D 68.262 B142,B144
A4059 d 15.000 B136 02878 d 34.925 B142 13830 D 63.500 B144 21075 d 19.050 B136
A4138 D 34.988 B136 03062 d 15.875 B136 13889 d 38.100 B144 21212 D 53.975 B136
4335 D 90.488 B146 03162 D 41.275 B136 14123 A d 31.750 B140 L21511 D 34.988 B136
4388 d 41.275 B146 05062 d 15.875 B136 14125 A d 31.750 B140 L21549 d 15.875 B136
4535 D 104.775 B152 05068 d 17.462 B136 14130 d 33.338 B142 22168 d 42.862 B146
4595 d 53.975 B152 05075 d 19.050 B136 14131 d 33.338 B142 22325 D 82.550 B146
A5069 d 17.455 B136 05079 d 19.990 B136 14137 A d 34.925 B142 23100 d 25.400 B138
A5144 D 36.525 B136 05175 D 44.450 B136 14138 A d 34.925 B142 23256 D 65.088 B138
5335 D 103.188 B148 05185 D 47.000 B136 14139 d 34.976 B142 23621 D 73.025 B142
5356 d 44.450 B148 07079 d 20.000 B136 14274 D 69.012 B140,B142 23691 d 35.000 B142
5535 D 122.238 B152,B154 07087 d 22.225 B136 14276 D 69.012 B140,B142 24720 D 76.200 B146
5566 d 55.562 B152 07097 d 25.000 B138 14283 D 72.085 B142 24721 D 76.200 B146
5582 d 60.325 B154 07098 d 24.981 B138 15100 d 25.400 B138 24780 d 41.275 B146
5584 d 63.500 B154 07100 d 25.400 B138 15101 d 25.400 B138 25520 D 82.931 B146,B148
5735 D 135.733 B158,B160 07100 SA d 25.400 B138 15106 d 26.988 B138 25521 D 83.058 B146
5760 d 76.200 B158 07196 D 50.005 B136,B138 15112 d 28.575 B138 25523 D 82.931 B146,B148
5795 d 77.788 B160 07204 D 51.994 B136,B138 15113 d 28.575 B138 25577 d 42.875 B146
A6062 d 15.875 B136 07205 D 52.001 B138 15116 d 30.112 B140 25578 d 42.862 B146
A6067 d 16.993 B136 08118 d 30.162 B140 15117 d 30.000 B140 25580 d 44.450 B146
A6075 d 19.050 B136 08125 d 31.750 B140 15118 d 30.213 B140 25584 d 44.983 B148
A6157 D 39.992 B136 08231 D 58.738 B140 15119 d 30.213 B140 25590 d 45.618 B148
6220 D 127.000 B150,B152 09062 d 15.875 B136 15120 d 30.213 B140 25820 D 73.025 B142
6279 d 50.800 B150 09067 d 19.050 B136 15123 d 31.750 B140 25821 D 73.025 B142,B144
6280 d 53.975 B152 09074 d 19.050 B136 15125 d 31.750 B140 25877 d 34.925 B142
6320 D 135.755 B154,B156 09078 d 19.050 B136 15126 d 31.750 B140 25878 d 34.925 B142
6376 d 60.325 B154 09081 d 20.625 B136 15245 D 62.000 B138,B140 25880 d 36.487 B144
6379 d 65.088 B156 09194 D 49.225 B136 15250 D 63.500 B140 26118 d 30.000 B140
6420 D 149.225 B152,B156,B158 09195 D 49.225 B136 15250 X D 63.500 B138 26131 d 33.338 B142
6454 d 69.850 B156 09196 D 49.225 B136 15520 D 57.150 B138 26283 D 72.000 B140,B142
6455 d 57.150 B152 11162 d 41.275 B146 15523 D 60.325 B138 26820 D 80.167 B146
6460 d 73.025 B158 11300 D 76.200 B146 15578 d 25.400 B138 26822 D 79.375 B146
6461 d 76.200 B158 11520 D 42.862 B136 15580 d 26.988 B138 26823 D 76.200 B146
6535 D 161.925 B158,B160,B162 11590 d 15.875 B136 16150 d 38.100 B144 26882 d 41.275 B146
6536 D 161.925 B158 LM11710 D 39.878 B136 16284 D 72.238 B144 26884 d 42.875 B146
6559 d 82.550 B160 LM11749 d 17.462 B136 16929 D 74.988 B146 27620 D 125.412 B160
6575 d 76.200 B158 LM11910 D 45.237 B136 16986 d 43.000 B146 27687 d 82.550 B160
6576 d 76.200 B158 LM11949 d 19.050 B136 17098 d 24.981 B138 27689 d 83.345 B160
6580 d 88.900 B162 12168 d 42.862 B146 17118 d 30.000 B140 27690 d 83.345 B160
9121 D 152.400 B154,B156 12303 D 76.992 B146 17244 D 62.000 B138,B140 27820 D 80.035 B144
9180 d 61.912 B154 12520 D 49.225 B136 17520 D 42.862 B136 27880 d 38.100 B144
9185 d 68.262 B156 12580 d 20.638 B136 17580 d 15.875 B136 28138 d 34.976 B142
9220 D 161.925 B158 M12610 D 50.005 B136 17831 D 79.985 B148 28315 D 80.000 B142
9285 d 76.200 B158 M12648 d 22.225 B136 17887 d 45.230 B148 28521 D 92.075 B150
9320 D 177.800 B160 M12649 d 21.430 B136 18200 d 50.800 B150 28580 d 50.800 B150
9321 D 171.450 B160,B162 LM12710 D 45.237 B136 18337 D 85.725 B150 28584 d 52.388 B150
9378 d 76.200 B160 LM12711 D 45.975 B136 18520 D 73.025 B144 28622 D 97.630 B152
9380 d 76.200 B160 LM12749 d 22.000 B136 18590 d 41.275 B144 28680 d 55.562 B152
9385 d 84.138 B162 13175 d 44.450 B146 18620 D 79.375 B148 28920 D 101.600 B154
02420 D 68.262 B138,B140 13181 d 46.038 B148 18690 d 46.038 B148 28921 D 100.000 B154
02473 d 25.400 B138 13318 D 80.962 B146,B148 18720 D 85.000 B150 28985 d 60.325 B154
02474 d 28.575 B138 13620 D 69.012 B144 18790 d 50.800 B150 29520 D 107.950 B154
02475 d 31.750 B140 13621 D 69.012 B144 19138 d 34.976 B142 29586 d 63.500 B154
C 28 C 29
C001-034E.indd 28-29 11/20/13 5:04:02 PM

APPENDICES
29620 D 112.712 B156,B158 42690 d 77.788 B160 49585 d 50.800 B150 67920 D 282.575 B170
29630 D 120.650 B156 43118 d 30.162 B140 52387 d 98.425 B164 67983 d 203.200 B170
29675 d 69.850 B156 43131 d 33.338 B142 52393 d 100.012 B164 67985 d 206.375 B170
29685 d 73.025 B158 43300 D 76.200 B140 52400 d 101.600 B166 L68110 D 59.131 B142
LM29710 D 65.088 B144 43312 D 79.375 B142 52618 D 157.162 B164,B166 L68111 D 59.975 B142
LM29711 D 65.088 B144 44143 d 36.512 B144 52637 D 161.925 B164,B166 L68149 d 35.000 B142
LM29748 d 38.100 B144 44150 d 38.100 B144 53150 d 38.100 B144 68450 d 114.300 B166
LM29749 d 38.100 B144 44157 d 40.000 B144 53162 d 41.275 B146 68462 d 117.475 B166
31520 D 76.200 B142 44162 d 41.275 B146 53176 d 44.450 B148 68709 D 180.000 B166
31594 d 34.925 B142 44348 D 88.501 B144,B146 53177 d 44.450 B148 68712 D 180.975 B166
33262 d 66.675 B156 L44610 D 50.292 B138 53178 d 44.450 B148 JL69310 D 63.000 B144
33275 d 69.850 B156 L44640 d 23.812 B138 53375 D 95.250 B144,B148 JL69349 d 38.000 B144
33281 d 71.438 B158 L44643 d 25.400 B138 53387 D 98.425 B146,B148 71412 d 104.775 B166
33287 d 73.025 B158 L44649 d 26.988 B138 55175 d 44.450 B148 71425 d 107.950 B166
JHM33410 D 55.000 B138 45220 D 104.775 B152 55187 d 47.625 B148 71437 d 111.125 B166
JHM33449 d 24.000 B138 45221 D 104.775 B152 55200 d 50.800 B150 71450 d 114.300 B166
33462 D 117.475 B156,B158 45289 d 57.150 B152 55200 C d 50.800 B150 71453 d 115.087 B166
33821 D 95.250 B150 L45410 D 50.292 B140 55206 d 52.388 B150 71750 D 190.500 B166
33889 d 50.800 B150 L45449 d 29.000 B140 55437 D 111.125 B148,B150 72187 d 47.625 B148
34300 d 76.200 B158 46143 d 36.512 B144 55443 D 112.712 B148 72200 d 50.800 B150
34306 d 77.788 B160 46162 d 41.275 B146 56418 d 106.362 B166 72200 C d 50.800 B150
34478 D 121.442 B158,B160 46176 d 44.450 B146 56425 d 107.950 B166 72212 d 53.975 B152
36620 D 193.675 B168 46368 D 93.662 B144,B146 56650 D 165.100 B166 72212 C d 53.975 B152
36690 d 146.050 B168 46720 D 225.425 B168 59200 d 50.800 B150 72218 d 55.562 B152
36920 D 227.012 B170 46780 d 158.750 B168 59429 D 108.966 B150 72218 C d 55.562 B152
36990 d 177.800 B170 47420 D 120.000 B156,B158 64433 d 109.992 B166 72225 C d 57.150 B152
37425 d 107.950 B166 47487 d 69.850 B156 64450 d 114.300 B166 72487 D 123.825 B148,B150,B152
37625 D 158.750 B166 47490 d 71.438 B158 64700 D 177.800 B166 LM72810 D 47.000 B138
M38510 D 66.675 B142 47620 D 133.350 B158,B160 65200 d 50.800 B150 LM72849 d 22.606 B138
M38511 D 65.987 B142 47680 d 76.200 B158 65212 d 53.975 B152 74500 d 127.000 B168
M38547 d 35.000 B142 47685 d 82.550 B160 65237 d 60.325 B154 74525 d 133.350 B168
M38549 d 34.925 B142 47686 d 82.550 B160 65320 D 114.300 B148 74537 d 136.525 B168
39236 d 60.000 B154 47687 d 82.550 B160 65385 d 44.450 B148 74550 d 139.700 B168
39250 d 63.500 B154 47820 D 146.050 B164 65500 D 127.000 B150,B152,B154 74850 D 215.900 B168
39412 D 104.775 B154 47890 d 92.075 B164 66187 d 47.625 B148 74856 D 217.488 B168
39520 D 112.712 B154,B156 47896 d 95.250 B164 66462 D 117.475 B148 77375 d 95.250 B164
39521 D 112.712 B156 48120 D 161.925 B166 66520 D 122.238 B152,B154 77675 D 171.450 B164
39585 d 63.500 B154 48190 d 107.950 B166 66584 d 53.975 B152 78225 d 57.150 B152
39590 d 66.675 B156 48220 D 182.562 B168 66585 d 60.000 B154 78250 d 63.500 B154
41100 d 25.400 B138 48282 d 120.650 B168 66587 d 57.150 B152 LM78310 D 62.000 B142
41125 d 28.575 B138 48286 d 123.825 B168 LM67010 D 59.131 B138,B140 LM78310 A D 62.000 B142
41126 d 28.575 B138 48290 d 127.000 B168 LM67043 d 28.575 B138 LM78349 d 35.000 B142
41286 D 72.626 B138 48320 D 190.500 B168 LM67048 d 31.750 B140 78537 D 136.525 B154
42350 d 88.900 B162 48385 d 133.350 B168 67320 D 203.200 B168 78551 D 140.030 B152,B154
42362 d 92.075 B164 48393 d 136.525 B168 67322 D 196.850 B168 78571 D 144.983 B152
42368 d 93.662 B164 LM48510 D 65.088 B142 67388 d 127.000 B168 HM81610 D 47.000 B136
42375 d 95.250 B164 LM48511 D 65.088 B142 67389 d 130.175 B168 HM81649 d 16.000 B136
42376 d 95.250 B164 LM48548 d 34.925 B142 67390 d 133.350 B168 M84210 D 59.530 B138
42381 d 96.838 B164 48620 D 200.025 B168 67720 D 247.650 B168,B170 M84249 d 25.400 B138
42584 D 148.430 B164 48685 d 142.875 B168 67780 d 165.100 B168 M84510 D 57.150 B138
42587 D 149.225 B162,B164 49175 d 44.450 B146 67787 d 174.625 B170 M84548 d 25.400 B138
42620 D 127.000 B158,B160 49176 d 44.450 B146 67790 d 177.800 B170 M86610 D 64.292 B138,B140
42687 d 76.200 B158 49368 D 93.662 B146 67820 D 266.700 B170 M86643 d 25.400 B138
42688 d 76.200 B158 49520 D 101.600 B150 67885 d 190.500 B170 M86647 d 28.575 B138
C 30 C 31
C001-034E.indd 30-31 11/20/13 5:04:03 PM

APPENDICES
CONE, CUP D:CUP (Outside Dia.) CONE, CUP D:CUP (Outside Dia.) CONE, CUP D:CUP (Outside Dia.) CONE, CUP
D:CUP (Outside Dia.)
M86648 A d 30.955 B140 HH221432 d 87.312 B162 HM518410 D 152.400 B162 HM801310 D 82.550 B144
M86649 d 30.162 B140 HH221434 d 88.900 B162 HM518445 d 88.900 B162 HM801346 d 38.100 B144
M88010 D 68.262 B140,B142 HH221440 d 95.250 B164 LM522510 D 159.987 B166 M802011 D 82.550 B146
M88043 d 30.162 B140 HH221442 d 98.425 B164 LM522546 d 107.950 B166 M802048 d 41.275 B146
M88046 d 31.750 B140 HH221447 d 99.982 B164 LM522548 d 109.987 B166 HM803110 D 88.900 B146
M88048 d 33.338 B142 HH221449 d 101.600 B166 LM522549 d 109.987 B166 HM803145 d 41.275 B146
HM88510 D 73.025 B140,B142 HH224310 D 212.725 B166 JHM522610 D 180.000 B166 HM803146 d 41.275 B146
HM88542 d 31.750 B140 HH224335 d 101.600 B166 JHM522649 d 110.000 B166 HM803149 d 44.450 B146
HM88547 d 33.338 B142 HH224340 d 107.950 B166 JHM534110 D 230.000 B170 M804010 D 88.900 B148
HM88610 D 72.233 B138,B140,B142,B144 HH224346 d 114.300 B166 JHM534149 d 170.000 B170 M804049 d 47.625 B148
HM88630 d 25.400 B138 M224710 D 174.625 B168 LM603011 D 77.788 B148 HM804810 D 95.250 B146,B148,B150
HM88638 d 32.000 B140 M224748 d 120.000 B168 LM603012 D 77.788 B148 HM804840 d 41.275 B146
HM88648 d 35.717 B144 LL225710 D 165.895 B168 LM603049 d 45.242 B148 HM804843 d 44.450 B148
HM88649 d 34.925 B142 LL225749 d 127.000 B168 L610510 D 94.458 B154 HM804846 d 47.625 B148
HM89410 D 76.200 B142,B144 HM231110 D 236.538 B168 L610549 d 63.500 B154 HM804848 d 48.412 B150
HM89411 D 76.200 B142 HM231140 d 146.050 B168 JM612910 D 115.000 B158 HM804849 d 48.412 B150
HM89443 d 33.338 B142 M236810 D 260.350 B170 JM612949 d 70.000 B158 HM807010 D 104.775 B148,B150
HM89444 d 33.338 B142 M236849 d 177.800 B170 LM613410 D 112.712 B156 HM807011 D 104.775 B150
HM89446 d 34.925 B142 LM300811 D 68.000 B144 LM613449 d 69.850 B156 JHM807012 D 105.000 B150
HM89446 A d 34.925 B142 LM300849 d 41.000 B144 HM617010 D 142.138 B162 HM807040 d 44.450 B148
HM89449 d 36.512 B144 L305610 D 80.962 B150 HM617049 d 85.725 B162 HM807044 d 49.212 B150
99100 D 254.000 B168 L305649 d 50.800 B150 L623110 D 152.400 B166 JHM807045 d 50.000 B150
99550 d 139.700 B168 JH307710 D 110.000 B152 L623149 d 114.300 B166 HM807046 d 50.800 B150
99575 d 146.050 B168 JH307749 d 55.000 B152 JLM710910 D 105.000 B156 JLM813010 D 110.000 B158
99587 d 149.225 B168 JHM318410 D 155.000 B162 JLM710949 d 65.000 B156 JLM813049 d 70.000 B158
99600 d 152.400 B168 JHM318448 d 90.000 B162 JLM714110 D 115.000 B158 JLM820012 D 150.000 B164
LM102910 D 73.431 B148 L327210 D 177.008 B168 JLM714149 d 75.000 B158 JLM820048 d 100.000 B164
LM102949 d 45.242 B148 L327249 d 133.350 B168 JM714210 D 120.000 B158 JM822010 D 165.000 B166
JLM104910 D 82.000 B150 LM328410 D 187.325 B168 JM714249 d 75.000 B158 JM822049 d 110.000 B166
LM104911 D 82.550 B150 LM328448 d 139.700 B168 H715311 D 136.525 B154,B156,B158 JHM840410 D 300.000 B170
LM104911 A D 82.550 B150 H414210 D 136.525 B156,B158 H715334 d 61.912 B154 JHM840449 d 200.000 B170
LM104912 D 82.931 B150 H414245 d 68.262 B156 H715340 d 65.088 B156 HM903210 D 95.250 B148
LM104947 A d 50.000 B150 H414249 d 71.438 B158 H715341 d 66.675 B156 HM903247 d 44.450 B148
JLM104948 d 50.000 B150 JH415610 D 145.000 B158 H715343 d 68.262 B156 HM903249 d 44.450 B148
LM104949 d 50.800 B150 JH415647 d 75.000 B158 H715345 d 71.438 B158 HM911210 D 130.175 B152
M201011 D 73.025 B144 LM501310 D 73.431 B144 JM716610 D 130.000 B162 HM911242 d 53.975 B152
M201047 d 39.688 B144 LM501314 D 73.431 B144 JM716648 d 85.000 B162 H913810 D 146.050 B154,B156
JM205110 D 90.000 B150 LM501349 d 41.275 B144 JM716649 d 85.000 B162 H913842 d 61.912 B154
JM205149 d 50.000 B150 LM503310 D 75.000 B148 JM718110 D 145.000 B162 H913849 d 69.850 B156
JM207010 D 95.000 B152 LM503349 d 46.000 B148 JM718149 d 90.000 B162
JM207049 d 55.000 B152 HH506310 D 114.300 B150 JM719113 D 150.000 B164
JH211710 D 120.000 B156 HH506348 d 49.212 B150 JM719149 d 95.000 B164
JH211749 d 65.000 B156 JLM506810 D 90.000 B152 JM720210 D 155.000 B164
HM212010 D 122.238 B154,B156 JLM506849 d 55.000 B152 JHM720210 D 160.000 B164
HM212011 D 122.238 B154,B156 JLM508710 D 95.000 B154 JM720249 d 100.000 B164
HM212044 d 60.325 B154 JLM508748 d 60.000 B154 JHM720249 d 100.000 B164
HM212046 d 63.500 B154 JM511910 D 110.000 B156 JL724314 D 170.000 B168
HM212047 d 63.500 B154 JM511946 d 65.000 B156 JL724348 d 120.000 B168
HM212049 d 66.675 B156 JM515610 D 130.000 B160 JL725316 D 175.000 B168
JH217210 D 150.000 B162 JM515649 d 80.000 B160 JL725346 d 125.000 B168
JH217249 d 85.000 B162 HM516410 D 133.350 B160 JM734410 D 240.000 B170
HM218210 D 147.000 B162 HM516448 d 82.550 B160 JM734449 d 170.000 B170
HM218248 d 90.000 B162 JHM516810 D 140.000 B162 JM738210 D 260.000 B170
HH221410 D 190.500 B162,B164,B166 JHM516849 d 85.000 B162 JM738249 d 190.000 B170
C 32 C 33
C001-034E.indd 32-33 11/20/13 5:04:04 PM

C001-034E.indd 34 11/20/13 5:04:05 PM
H3E.indd 1-2 11/20/13 5:04:51 PM
Rolling Bearings
Rolling Bearings
CAT. No. E1102m 2013 C-11 Printed in Japan NSK Ltd. First edition published in MAR. 2005
2013/10/16

E1102m PDF

Uploaded by

Copyright:

Available Formats

E1102m PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

E1102m PDF

Uploaded by

Copyright:

Available Formats

What types of rolling bearings are described in the document?

What types of rolling bearings are described in the document?

What information is provided about bearing selection?

What information is provided about bearing selection?

Rolling Bearings

Deep Groove Ball Brgs. B4

Angular Contact Ball Brgs. B46

Self-Aligning Ball Brgs. B76

Cylindrical Roller Brgs. B84

Tapered Roller Brgs. B110

Spherical Roller Brgs. B182

Needle Roller Brgs. B244

Ball Brg. Units B280

Plummer Blocks B304

Cylindrical Roller Brgs. for Sheaves B326 Sheaves

Roll-Neck Brgs. (4-Rows) Roll Neck

NSK Products and Appendices C1 Appendices

mikaesiE.indd 1-2 11/20/13 4:48:42 PM

CAT. No. E1102m

A001-005E.indd 1 11/20/13 4:49:05 PM

NSK Web site A http://www.nsk.com

A001-005E.indd 2-3 11/20/13 4:49:06 PM

A001-005E.indd 4-5 11/20/13 4:49:06 PM

Width Contact Angle

Fig. 1.1 Nomenclature for Bearing Parts

A007-023E.indd 6-7 11/20/13 4:49:25 PM

(Radial Bearings) (Thrust Bearings)

Single Automotive Clutch

A007-023E.indd 8-9 11/20/13 4:49:26 PM

A007-023E.indd 10-11 11/20/13 4:49:29 PM

A007-023E.indd 12-13 11/20/13 4:49:32 PM

Table 1. 1 Types and Characteristics of Rolling Bearings

Low Noise and A19

roller thrust bearings

DT pairs is possible, but

Including NNU type

Including NUP type

To be used with oil

also available but

KH, KV types are

B5 B5 B47 B47 B85 B115 B207 B207

Excellent Good Fair One direction

A007-023E.indd 14-15 11/20/13 4:49:34 PM

A Misalignment of inner and A18

A007-023E.indd 16-17 11/20/13 4:49:36 PM

A007-023E.indd 18-19 11/20/13 4:49:37 PM

A007-023E.indd 20-21 11/20/13 4:49:38 PM

Table 4. 1 Representative Bearing Mounting Arrangements

Vertical arrangements Remarks Application Examples

fThis arrangement is widely used since it can Pinion shafts of automotive

Continued on next page

A007-023E.indd 22-23 11/20/13 4:49:39 PM

may be defined as noise life, abrasion life, grease life, equipment

mounting, or insufficient maintenance. railway rolling stock

a certain period of time, 10 % of them fail as a result of ..........(Refer to Page A30)

flaking caused by rolling fatigue. The total number of 1 3

is often expressed by the total number of operating = (0.03n)- 3 = (0.03n)- 10

A024-057E.indd 24-25 11/20/13 4:50:10 PM

Table 5.3 Temperature Factor f t Table 5.4 Reliability Factor a 1