User Manual

WatchPower

Management Software for Inverter

 Table of Contents
1. WatchPower Overview ..................................................................................... 1

1.1. Introduction ..................................................................................................... 1

1.2. Features .......................................................................................................... 1

2. WatchPower Install and Uninstall .................................................................... 1

2.1. System Requirement ......................................................................................... 1

2.2. Software Install ................................................................................................ 2

2.3. Software Uninstall ............................................................................................. 3

3. Tray Application ............................................................................................... 3

3.1. Startup ............................................................................................................ 3

3.2. Configuration .................................................................................................... 4

3.3. Software Upgrade ............................................................................................. 4

3.4. SNMP Manager ................................................................................................. 5

3.5. Open Monitor.................................................................................................. 18

3.6. Icon and Software Status ................................................................................. 18

3.7. Message Board ............................................................................................... 18

3.8. Exit ............................................................................................................... 19

4. GUI Interface ................................................................................................. 20

4.1. WatchPower Configuration ................................................................................ 23

4.2. Device control ................................................................................................ 29

4.3. View .............................................................................................................. 38

4.4. Log in and Log out .......................................................................................... 41

4.5. Rename ......................................................................................................... 42

4.6. Language ....................................................................................................... 44

4.7. Help .............................................................................................................. 44

1. WatchPower Overview
1.1. Introduction
WatchPower is an inverter monitoring software which can monitor multiple devices via
serial port at the same time. The major functions of WatchPower monitoring software
include data log for devices, alarm messages, fault messages, and parameter setting
for devices.

1.2. Features

Automatic and real-time data acquisition of devices and secured data log saving
Graphic display of device data for quick and easy reading
Warning notifications or fault alarms via mobile messenger, tray message and
e-mail
Easy diagnosis from event statistics
Supports online upgrade and manually upgrade

2. WatchPower Install and Uninstall

2.1. System Requirement
512 MB physical memory at least (1 GB is recommended)
2GB hard disk space at least
Administrator authority is required
More than 32-bit colors and 1280 x 800 or above resolution display is
recommended
An available communication port is needed
Platforms supported by software are listed below:
Windows XP/2000/2003/Vista/2008 (32-bit & 64-bit)
Windows 7/8 /8.1/10(32-bit & 64-bit)
Windows SBS 2011
Linux RedHat 8, 9
Linux RedHat Enterprise AS3, AS5, AS6 (32-bit)
Linux RedHat Enterprise AS6 (64-bit)
Linux RedHat Enterprise 5.2 (32-bit & 64-bit)
Linux SUSE 10 (32-bit & 64-bit)
Linux Cent OS 5.x ,6.x(32-bit & 64-bit)
Linux Ubuntu 8.X, 9.X, 10.X (32-bit )
Linux Ubuntu 10.X (64-bit)
Linux Ubuntu 12.04 (32-bit & 64-bit)
Linux Fedora 5
Linux OpenSUSE 11.2 (32-bit & 64-bit)
Linux Debian 5.x, 6.x (32-bit)
Linux Debian 6.x (64-bit)
Mac OS 10.x (64-bit)

1
2.2. Software Install
WatchPower is a portable application. Its no need to install this software. You may
simply double click WatchPower.exe to automatically run this software after extracting
files.

Windows Version:

Macosx Version:

Linux Version:

2
NOTE: If its not running after double clicking WatchPower in Linux OS, please check if
there is authority to run WatchPower with terminal.

If it shows Permission denied in dialog, please send command for elevation of

privilege to run WatchPower.

2.3. Software Uninstall

This software becomes portable software. Its easy to delete all files for software
uninstallation.

3. Tray Application
3.1. Startup

The Installer will leave a shortcut icon called WatchPower on your desktop. Refer to
Diagram 3-1. Simply double click the shortcut icon. Then, it will start the software and
display a service icon located in tray. It will pop up function menu by clicking right
button of the mouse. Refer to below diagram 3-2.

Diagram 3-1

Diagram 3-2

3
3.2. Configuration
3.2.1. Software Upgrades
Refer to Diagram 3-3 for the detailed configuration for online upgrade:
Specify the URL for update files: This is the directory to online update
software. Please do not change it unless its instructed by software
manufacturer.
Save files to: The directory to save files in your hard drive.
Online auto-update: If selected, it will automatically check if there is any
new version launched online every 1 hour.
If applying online upgrade, please follow below for configuration:
1. Select Apply the proxy configuration.
2. Enter IP address and port of server.
3. If ID identification is requested, select Enable authentication and enter
User Name and Password.
Connection test: Click this button to test if all configurations are set up well.

Diagram 3-3
3.2.2. Configuration Saved
Click Apply button to save all changes in Configuration page. Click Cancel to stop the
change.

3.3. Software Upgrade

Software upgrades includes online upgrade and manually upgrade.
Online Upgrade:
Click Online Upgrade to search the latest software version. If there is new

4
 version, it will automatically download and upgrade. Refer to Diagram 3-4.

Diagram 3-4
Manually Upgrade:
Users can manually upgrade the software. Follow below steps:
1Click Manually Upgrade from function menu. Refer to Diagram 3-5.

Diagram 3-5
2Click Browse to choose file directory. Then, click Upgrade to upgrade
software. Refer to Diagram 3-6.

Diagram 3-6

3.4. SNMP Manager

SNMP Manager is a plugin utility for WatchPower software. Users can search and
operate all SNMP devices in the LAN via this interface. Then, WatchPower will
automatically search and monitor these SNMP devices. Please open SNMP Manager by
clicking right button of the mouse on service icon. It has four sections as marked in the
illustration below:

5
A. Function menu offers complete tool-set for navigating and setting the GUI.

B. SNMP device list can list down all SNMP devices located in current IP address.

C. Configuration area includes IP settings, online upgrade, password management,

and static trap address.

D. Output window displays all messages for operations

3.4.1. SNMP Device List

The default value in window list would be current PC IP address. For example, if IP address

of current PC is 192.168.102.10, it will display 192.168.102 in list when first enabling

SNMP Manager.

Scan

You may enter specific IP address and then click Scan button to search.

Add

Click Add button and it will pop up a window to ask for entering specific IP address. Then,

click Apply button to add IP address (Subnet). Refer to Diagram 3-7.

6
 Diagram 3-7

Delete

Select unnecessary IP address from list and click Del button to delete from list.

SNMP Status

After one IP address is selected from the IP list, SNMP status will display 0 or 1. If there is

program inside SNMP card, SNMP status would show 1. If there is no program inside, SNMP

status would display 0. If there is no IP selected, SNMP status will be the default ---. Refer

to Diagram 3-8.

Diagram 3-8

7
 Reset

If its necessary to restart the device IP addresses, please select the "SNMP reset enable"
and click on the "Reset" button. Then, after entering password to confirm the login, you can
restart the device. Please follow below steps to execute this action:

Step 1: Select from the IP list of equipment needed to restart IP. Refer to Diagram 3-9.

Diagram 3-9

Step 2: After IP is selected, please click the checkbox of SNMP reset enable. Then,

"Reset" button will become valid. Refer to Diagram 3-10.

Diagram 3-10

8
Step 3: Click the "Reset" button. It will prompt the dialog to confirm the operation. If Yes

is selected, it will prompt the dialog to confirm login. If No is selected, it will stop

this operation. Refer to Diagram 3-11.

Diagram 3-11

Step 4: After entering password and select "Login", you will be prompted to log in. Then,

selected device will be restarted. If Cancel is selected, it will stop this operation.

Diagram 3-12

NOTE: If changing MAC address of current device before reboot and current device is

obtained by DHCP (Automatically obtain IP address), you need to manually click

9
 Scan" button to get IP address after reboot.

3.4.2. SNMP Manager Function Menu

3.4.2.1. System
Login
When remote login to access SNMP devices, its necessary to verify ID. The default
password is 12345678.
Step1: Select System >> Login

Step2: Enter default password and then click Login button. Or click Cancel to cancel

login. Refer to Diagram 3-13.

Diagram 3-13

Logout

Log out system when access is no longer needed.

Quit

Select Quit to exit SNMP Manager.

3.4.2.2. Settings

Basic Info

Basic information display IP address and Mac address. Refer to Diagram 3-14.

10
 Diagram 3-14

IP Setting

Part 1: Change MAC address

Step 1: Select IP address from IP list. It will display MAC address of device in the output

window. If its necessary to modify the MAC address of the device, click

checkbox of "Change". Refer to Diagram 3-15.

Diagram 3-15

Step 2: After checkbox of "Change" is selected, enter new MAC address into column.

11
 "Apply" button will become valid to click. Refer to Diagram 3-16.

Diagram 3-16

Step 3: After modifying MAC address, click "Apply" button. Then it will prompt a dialog

to confirm the operation. Refer to Diagram 3-17.

Diagram 3-17

Step 4: If Yes is selected, it will prompt "Operation success" in output window. Refer to

Diagram 3-18.

12
 Diagram 3-18

Part 2: There are two methods to obtain IP address:

Automatically obtain IP address (DHCP)

Manually configure IP address

The system will default automatically obtain IP addresses. If there is no this kind of service

provided in LAN, the default IP will display as 192.168.102.230, Net mask as

255.255.255.0 and default gateway as 0.0.0.0. Refer to Diagram 3-19.

Diagram 3-19

13
Online upgrade

There are three methods for online upgrade:

Upgrade the selected devices: It will upgrade all SNMP devices listed on the window.

Upgrade all un-upgraded devices: It will only upgrade SNMP devices which are not

using the same version as current SNMP device is.

Force to upgrade all devices: No matter what kinds of version are used for SNMP

devices listed in the window list, it will upgrade to the version used for current SNMP

device. Refer to Diagram 3-20.

Diagram 3-20

Step 1: Click Browse button to choose program file. Refer to Diagram 3-21.

14
 Diagram 3-21

Step 2: Click Upgrade button to execute upgrade action. Refer to Diagram 3-22.

Diagram 3-22

Step 3: When upgrade is complete, you may check the message in output window. Refer to

Diagram 3-23.

15
 Diagram 3-23

NOTE: If abnormal situation occurs during upgrade process, the system will automatically

re-start the upgrade operation. If this interruption occurs five times, system will

automatically stop this operation. At this time, please check if LAN is working well.

System manager

You may modify single password for one SNMP device or all passwords for all SNMP devices.

Refer to Diagram 3-24

Diagram 3-24

Select device: Choose to change password for selected SNMP device on the window

16
 list.

Select all: Choose to change passwords for all SNMP devices on the window list

Enter original password, new password and re-enter new password to confirm. Then, click

Apply button to apply password change.

NOTE: The length of password is 8~15 digits. If this password change is applied for all

SNMP devices, all SNMP devices passwords must be consistent.

Static trap address

You may configure two static trap addresses and change trap port in SNMP Manager. The

default trap port is 162. Refer to Diagram 3-25.

Diagram 3-25

NOTE: The SNMP device could provide 2 static trap addresses and 8 dynamic trap

addresses. The SNMP device will automatically obtain IP address of host machine which

installed monitoring software as dynamic trap address. If one of dynamic trap address is

inactive for over 10 minutes, SNMP device will automatically release it and obtain a new

dynamic trap address.

3.4.2.3. Language

SNMP Manager offers 12 languages:

Chinese(Simplified)

Chinese(Traditional)

17
 English

German

Italian

Polish

Portuguese

Russian

Spanish

Turkish

Ukrainian

French

The default language setting would be English.

3.4.2.4. Help

About: Click Help menu and select About item. It represents the copyright

information about software

3.5. Open Monitor

Click Open Monitor to open the monitoring webpage of WatchPower.

3.6. Icon and Software Status

Connecting devices: and will rotate as an animation
When receiving event message with devices connected: will flash for
reminder
When receiving event message without devices connected: will flash for
reminder

3.7. Message Board

Users can check message board for event list. Refer to Diagram 3-26

18
 Diagram 3-26

3.8. Exit
Click Exit to exist monitor application.

19
4. GUI Interface
There are five sections in GUI interface as marked in the illustration below:

Diagram 4-1
A. Function Menu offers complete tool-set for navigating and setting the GUI.
B. Shortcut Menu provides short cuts to more commonly used functions.
C. Inverter Navigation indicates all devices.
D. Current Monitoring Information displays User ID, monitored inverter ID.
E. Main Window displays power flow, operation information, device information
and rated information of current monitored inverter. Refer to Diagram 4-2.

Diagram 4-2

20
1 Power flow:
There are five device icons: solar panel, battery, inverter, load and the utility. It
displays dynamic power flow with these five device icons.
Power on and Standby mode: Inverter wont power the load until ON switch is
pressed. Qualified utility or PV source can charge battery in standby mode.

Power on Mode

Standby Mode
Line mode: Inverter will power the load from utility. Qualified utility or PV source
can charge battery.

Line Mode

21
 Battery mode: Inverter will power the load from battery or PV panel. Only PV
source can charge battery.

Battery Mode
Fault mode: Some faults occurred in inverter and no power output is generated
from inverter. Qualified utility or PV source still can charge battery.

Fault Mode
2 Basic Information:
It displays information of AC voltage, AC frequency, PV input voltage, Battery
voltage, Battery capacity, Charging current, Output voltage, Output frequency,
Output apparent power, Output active power and Load percent.
3 Product information:
Product information displays Mode type, Topology, Main CPU version and Secondary
CPU version.
4 Rated information:
Rated information displays information of Nominal AC voltage, Nominal AC current,

22
 Rated battery voltage, Nominal output voltage, Nominal output frequency, Nominal
output current, Nominal output apparent power and Nominal output active power.

4.1. WatchPower Configuration

4.1.1. Basic
It is to set up parameters for display. Select WatchPower Configuration>>Basic. Refer
to Diagram 4-3.

Diagram 4-3
1. Page refresh interval: This interval time will determine how long the web page is
refreshed. Setting range is from 5 to 600 seconds. The default setting is 5
seconds.
2. Devices scan interval: This interval time will determine how long to scan
connected devices. The setting range is from 5 to 600 seconds. The default setting
is 5 seconds.
3. Record interval: This interval time will determine how long to record monitoring
data of inverters into database. The setting range is from 30 to 600 seconds. The
difference between each option is 30 seconds. The default setting is 60 seconds.
4. Date format: This system supports 4 different formats, YYYY-MM-DD,
YYYY/MM/DD, MM-DD-YYYY and MM/DD/YYYY. The default setting is
YYYY-MM-DD.
If any change is made, simply click Apply button. Then, the setting will be saved.
4.1.2. Password
Its password configuration for administrator only. Before operating and configuring the
software, please login first and modify the password. The default password is
administrator at first log in. Users can only browse inverter status and information
as Guest without login as an Administrator. A guest can not control or execute any
setting.

Step 1 Select WatchPower Configuration>>Password. Refer to Diagram 4-4.

23
 Diagram 4-4

Step 2 Enter old password, new password and re-type new password to confirm new
password. The new password should be at least 6 digits. Then, click Apply
button to successfully modify password for administrator.
NOTE1: Simply click Login button on the top right corner to log in the software.
NOTE2: If password is forgotten, its necessary to re-install the software.
4.1.3. SMS Setting
Its to enter SMS receiver list. In the event of an alarm occurring, a message about
inverter status will be sent to the specified users via mobile phone. For the event
receiving list, please configure in Event Action page (refer to section 4.1.5).

Step 1 Choose WatchPower Configuration >> SMS Setting. Refer to Diagram 4-5.

Diagram 4-5

Step 2 Select communication port and baud rate.

Step 3 Enter mobile phone numbers in Phone no. column and click Add button to

24
 add phone no. in Receivers List. To delete numbers, simply select phone no.
from Receivers list and click Delete.

Step 4 Click Apply button to save all changes. The Test button can be used to send
a test SMS to make sure all setting is correct. If all parameters are set up
correctly, system will send a test message to all receivers and pop up a
successful message. (Refer to Diagram 4-6) Otherwise, it will pop up a failure
dialog to indicate there is an error for parameter setting. (Refer to Diagram
4-7)

Diagram 4-6

Diagram 4-7
NOTE: Its required to plug in a GSM modem if sending a SMS to mobile phone.

25
4.1.4. E-mail
This configuration is allowed to send an alarm mail from SMTP server. For the event
receiving list, please configure in Event Action page (refer to section 4.1.5).
To use this function, the e-mail service must be correctly configured in the computer. All
columns in this function page are default empty. This action cant be executed without
the SMTP information, e-mail account and password. Besides, the sender account
should be allowed for SMTP/POP3 forwarding.

Step 1 Select WatchPower Configuration >> E-mail. Refer to Diagram 4-8.

Diagram 4-8

Step 2 Enter SMTP server, Port, Send from E-mail address, User name and password.
Click checkbox if password authentication is needed to verify password.

26
 NOTE: If using Exchange Server for mailbox system, its required to configure
Exchange server domain name in SMTP server. Beside, please click checkbox
of Exchange server" and click "Apply" button.

Step 3 Enter receivers' e-mail accounts in E-mail column. Then, click Add to add into
Receivers list. To delete e-mail account, simply select accounts from Receivers
list and click Delete button.

Step 4 Click Apply to save all changes. The Test button can be used to send a test
e-mail to all receivers to confirm correct operation. When the test e-mails are
successfully sent to specific recipients, it will pop up a successful message on
operated personal computer. Otherwise, it will pop up a failure dialog to
indicate there is an error for parameter setting.
4.1.5. Event action
Its to configure response actions for events. It provides four response actions after
events occur.
1. Event record: It will record event to data log in software after events occur.
This function is default selected.
2. Warning message(s): It will send event message to tray.
3. SMS: It will send event message to specific mobile phone numbers after events
occur.
4. E-mail: It will send event e-mail to assigned e-mail accounts after events occur.

Step 1 Select WatchPower Configuration >> Event actions. Refer to Diagram 4-9.

Step 2 Select action methods by clicking checkbox.

Step 3 Click Apply button to save all configurations.

Diagram 4-9
NOTE1: When modifying receiver list in SMS or e-mail pages, its necessary to refresh
event action page to reload the updated receiver list.

27
4.1.6. Com. port Plug And Play Setting
To real-time monitor inverter device, it will scan each com. port anytime. In this way, it
will occupy communication ports. This function will release some communication ports
which are not connected with devices. To avoid any improper operation, in-used
communication ports will be displayed in disabled grey icons. Users can select "Allow
scanned" to re-scan or "No scanning to release communication ports based on
requirements.
Step 1: Select WatchPower configuration>> Com. port plug and play setting. Refer
to Diagram 4-10.

Diagram 4-10
Step 2: Click Refresh to reload the status of com. ports.
Step 3: Click No scanning to stop scanning on this com. port. Click Allow
scanned to start scanning on this com. port.
4.1.7. Modbus Serial Setting
This function is to set Modbus communication port with PCs that connected to
Modbus card via RS232/RS485 converter. The settings include Modbus port, Baud
rate, data bit, stop bit, parity and each Device ID in Modbus network.
Step 1 Select WatchPower configuration>> Modbus serial setting. Refer to

Diagram 4-11.

Step 2 Select Modbus port to connect PC.

Step 3 Select Device ID of connected inverter in Modbus network.

Step 4 Select Baud rate of com. port. The default setting is 19200.

Step 5 Modify Data bit of com. port. The default setting is 8.

Step 6 Modify Stop bit of com. port. The default setting is 1.

28
 Step 7 Modify Parity. The default setting is NONE.

Step 8 Click Apply button to save all changes.

Diagram 4-11

NOTE1: Click Refresh button to refresh the port list.

NOTE2: WatchPower supports multiple com. ports in multiple Modbus networks.

NOTE3: All configurations will be changed based on different port selection in Step

2.

NOTE4: The default device ID of inverter is 1.

NOTE5: If none of device ID is selected, it will be identified as not connecting with

any Modbus network.

NOTE6: If monitoring multiple Modbus networks, please repeat from step 2 to step
7 to set all ports.

4.2. Device control

4.2.1. Parameter Setting
This page is to activate some features and set up parameters for inverters.

Select Device Control >> Parameter Setting or select shortcut icon . Refer to
Diagram 4-12.

29
 Diagram 4-12

NOTE: This screen may be different for different model of inverter.

Step 1 Activate/Shut down functions by clicking Enable or Disable button. Some

parameters are allowed to change the numbers by clicking up-down arrows or
modify the numbers directly in the number column.

Step 2 Click Apply button to save the settings. Each function setting is saved by
clicking each Apply button.

Buzzer alarm: If disabled, buzzer wont be on when alarm/fault occurred. Vice

versa.

Power saving mode: If disabled, output will be on continuously when device is

operated in battery mode. If enabled, inverter output will be on or off depending on
connected loads detected or not. If the load is not detected, the output of inverter
will be off until load reaches a certain level. Check product manual for more details.

Backlight: If disabled, LCD backlight will be off when panel button is not operated
for 1 minute. Vice versa.

Overload auto restart: If disabled, the unit wont be restarted after overload occurs.
Vice versa.

Over temperature auto restart: If disabled, the unit won't be restarted after
over-temperature fault is solved. Vice versa.

Beeps while primary source interrupt: If enabled, buzzer will alarm when primary

30
 source is abnormal. Vice versa.

Overload bypass: If enabled, unit will transfer to line mode when overload
happened in battery mode. Vice versa.

LCD screen returns to default display screen after 1 min.: If enable, LCD screen will
return to default display screen after no button is pressed in one minute. Vice versa.

Solar power balance: This function is only available for 4KVA/5KVA models. When
enabled, solar input power will be automatically adjusted according to connected
load power. If disabled, solar input power will be the same to max. battery charging
power no matter how much loads are connected.

Fault code record: If enabled, fault code will be recorded in the inverter when any
fault happens.

Charger source priority: Click up-down arrows to set up charger source priority.
There are 4 options: utility first, solar first, solar and utility and Solar only. See
product manual for the details of these options. Refer to Diagram 4-13.

Diagram 4-13

Output source priority: Click up-down arrows to set up output source priority. There
are 3 options: utility first, solar first and SBU. See product manual for the details of
these options. Refer to Diagram 4-14.

31
 Diagram 4-14

AC input range: Click up-down arrows to set up suitable input range for connected
devices. When selecting "Appliance", it's allowed to connect home appliances.
When selecting "UPS", it's allowed to connect personal computer. For the detailed
input range for connected devices, please check product manual. Refer to Diagram
4-15.

Diagram 4-15

32
 Battery type: Select connected battery type. There are three options: AGM, Flooded
and User. Please refer to product manual for charging parameter for these three
battery types.

Output mode: In this setting, the options will be different based on different inverter
models. Refer to Diagram 4-16.

Diagram 4-16

Single: This inverter is set for singe operation.

Parallel: This inverter is set for parallel operation.

Phase R of 3 phase output: This inverter is set to support connected loads in

phase R of 3 phase output.

Phase S of 3 phase output: This inverter is set to support connected loads in

phase S of 3 phase output.

Phase T of 3 phase output: This inverter is set to support connected loads in

phase T of 3 phase output.

Output frequency: Nominal output frequency, 50Hz and 60Hz selectable.

Back to grid voltage: Click arrow to set up low battery voltage point. If SBU is
selected in output source priority, the inverter will transfer output source to grid
when battery voltage drop to low battery voltage point.

Max. charging current: Click arrow to set up maximum charging current. Maximum
charging current in different inverter model may be different. Please refer to

33
 product manual for the details.

Max. AC charging current: Click arrow to set up AC charging current. For the
detailed setting, please check inverter manual.

Back to discharge voltage: When battery voltage is higher than this setting voltage,
battery will be allowed to discharge.

Output voltage: Click arrow button to select output voltage in battery mode.

Diagram 4-17

Charging stage: Click arrow to select charging stage. Please set up based on the
battery type, specification and capacity.

Auto: Its determined by inverter itself according to battery capacity.

2-stage: constant current mode floating mode

3-stage: constant current mode constant voltage mode floating mode

34
 Diagram 4-18

Charging time in CV mode: Click arrow to setup charging duration in constant

voltage mode. Please set up based on the battery type, specification and capacity.

Auto: Its determined by inverter itself according to battery capacity.

Diagram 4-19

35
 Diagram 4-20

Bulk charging voltage (C.V. voltage): Click arrow to set up bulk charging voltage.
Please refer to product manual for the recommended bulk charging voltage based
on connected battery type.

Float charging voltage: Click arrow to set up float charging voltage. Please refer to
product manual for the recommended float charging voltage based on connected
battery type.

Max. charging time (C.V. stage): Click arrow to set up maximum charging time for
C.V. stage. The setting range is from 000 to 900. 000. If 000 is selected, the
charging time will depend on the device itself.

Battery cut-off voltage: In battery mode, when battery voltage is lower than cut-off
voltage point, inverter will shut down battery and transfer to fault mode.

36
Battery equalization setting: This section is only active for some inverters with
battery equalization function.

Diagram 4-21

Battery equalization: Enable or disable battery equalization function. Its necessary

to enable this function in software before executing this function in device.

Equalized time: Click up-down arrow to set up duration time for battery equalization.
The setting range is 5~900 minutes.

Equalized timeout: Click up-down arrow to set up the extended time to continue
battery equalization. The setting range is 5~900 minutes.

Equalization period: Click up-down arrow to set up the frequency for battery
equalization. The setting range is 0~90 days. When 0 is selected, it means this
function is activated every 24 hours.

Real-time activate battery equalization: Its real-time action to activate battery

equalization by selecting Activate. Select Cancel to stop equalization
immediately.

Equalization voltage: Click up-down arrow to set up the battery equalization voltage.
The setting range is 48.0V ~ 61.0V for 5KVA device and 25.0V ~ 31.5V for 3KVA
device.

37
4.2.2. Restore to the defaults
This function is allowed to restore all settings back to default values.

Select Device control >> Restore to the defaults. Refers to Diagram 4-22.

Diagram 4-22
NOTE: This screen may be different for different model of inverter.

4.3. View
4.3.1. Data
This function is to browse the working data of inverter saved in table or chart format.
Datasheets

Select View >>Data>>Datasheets or click shortcut icon . Refer to Diagram 4-23.

Select browsed device and period to display in the screen. Click Browse to get result.
Print: Print the listed data table.
Delete: Select specific data and click Delete button to delete the record.
Delete all: Click Delete All button to delete all records in the listed table.
Export: Click Export button to save listed table to local PC in .PDF file.
Export Excel: When selected and click Export, it will save listed table to
local PC in .xls file.

38
 Diagram 4-23
Charts
Select View >>Data>>Charts. Refer to Diagram 4-24.
Select browsed device and period. Then, click "Browse" to get the result.

Diagram 4-24

39
4.3.2. Event log

Select View >>Event log or click shortcut icon to enter event log.
It's to browse history events according to time duration selected. It lists all detailed
information and statistics for history events. Refer to Diagram 4-25.
Delete: Select specific data and click Delete button to delete the record.
Delete all: Click Delete All button to delete all records in the listed table.
Export: Click Export button to save listed table to local PC in .PDF file.

Export Excel: When selected and click Export, it will save listed table to local
PC in .xls file.

Diagram 4-25

4.3.3. Fault data log

Select View >>Fault data log .Refer to Diagram 4-26.

Its to record the latest fault event occurring on the inverter.

Delete: Select specific data and click Delete button to delete the record.

Delete all: Click Delete All button to delete all records on the listed table.

Export: Click Export button to save listed table to local PC in .PDF file.

Export Excel: When selected and click Export, it will save listed table to
local PC in .xls file.

40
 Diagram 4-26

4.4. Log in and Log out

This short cut icon is to display the login status. When icon is displayed, it

means user status is guest. When icon is displayed, it means user logins as
administrator.

Click icon and enter password to login the software. The default password is
administrator. Refer to Diagram 4-28.

Diagram 4-27

Click icon to log out. Then, the status will become to "guest". Refer to Diagram
4-27.

41
 Diagram 4-28

4.5. Rename
Its to rename devices from inverter navigation list. Serial number of devices will not be
changed.

Rename: Double click the device. Then right click the mouse and choose
Rename.

At this time, you may modify the device name.

After entering new name, be sure to press Enter keyboard to activate the
new name.

42
 Restore: Select one device and right click the mouse. Select Restore. Then,
the selected device name will be restored to default name.

Restore All: Select one device and right click the mouse. Select Restore All.
Then, all devices name will be restored to default names.

Before selecting Restore All:

After selecting Restore All

43
4.6. Language

Currently, software offers some languages for selection:

English

French

German

Polish

Spanish

Chinese(Simplified)

Chinese(Traditional)
When first using the software, it will search proper language to display according to
OS language.

4.7. Help
About: Click Help menu and select About item. It represents the copyright
information about software
Help: Click Help menu and select Online help item. It will open the help
manual. Before operating software, please read manual carefully.

44