Hydraulic Pump 16G
Hydraulic Pump 16G
Hydraulic Pump 16G
Page 1 of 6
Shutdown SIS
Previous Screen
Specifications
16G MOTOR GRADER HYDRAULIC SYSTEM AND STEERING
Media Number -REG01470-03 Publication Date -01/11/1981 Date Updated -10/10/2001
Hydraulic Pump
(8J6855) (Part of 8J6168 Pump Group)
Rotation is counterclockwise when seen from drive end.
The pump output tests are made with 5P2683 Stop installed to keep the pump at full stroke.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 6/7/2017
16G MOTOR GRADER 93U01179-02678 (MACHINE) POWERED BY 3406 ENGINE(... Page 2 of 6
(1) Torque to start turning shaft with pump more than 1/2 full of oil ... 20 lb. ft.(25 Nm)
(2) Shims: to get clearance (3) between impeller and pump head (check three places, 120
apart) ... .012 .003 in.(0.30 0.08 mm)
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 6/7/2017
16G MOTOR GRADER 93U01179-02678 (MACHINE) POWERED BY 3406 ENGINE(... Page 3 of 6
(5) Shim: to get clearance (6) between plate and slipper on piston (check three places, 120
apart) ... .003 .001 in.(0.08 0.02 mm)
Torque for bolts through plate ... 110 10 lb in.(12.4 1.1 Nm)
(12) Swashplate end clearance ... .000 to .005 in.(0.00 to 0.13 mm)
3: Remove O-ring (8) and install other cover with no shim pack.
Use only 3 bolts (10), approximately 120 between bolts. Tighten bolts four times.
NOTE: Swashplate (12) must freely turn after bolts (10) are tight.
4: Measure the distance between the cover and the pump body beside each bolt (10). Make a
record of each measurement and get the average of the measurements. The thickness for shim
pack (11) is the average measurement plus .008 in. (0.20 mm).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 6/7/2017
16G MOTOR GRADER 93U01179-02678 (MACHINE) POWERED BY 3406 ENGINE(... Page 4 of 6
5: If the thickness of shim pack (11) is .005 to .025 in. (0.13 to 0.63 mm), remove the cover.
Install O-ring (8), shim pack (11), the cover and the seven bolts and lockwashers.
NOTE: If the thickness of shim pack (11) is not .005 to .025 in. (0.13 to 0.63 mm), add .015 in.
(0.38 mm) to the thickness of shim pack (11) to get the total thickness of shim pack (11) and
shim pack (9). One half the total thickness (of both shim packs) is now the thickness for each
shim pack (9) and (11). Install shim packs and both covers [make certain O-ring (8) and
lockwashers are on the cover bolts].
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 6/7/2017
16G MOTOR GRADER 93U01179-02678 (MACHINE) POWERED BY 3406 ENGINE(... Page 5 of 6
(13) Angle for swashplate (12) to get the maximum stroke for the pistons ... 14 41' 0 10'
(14) Angle for swashplate (12) to get the minimum stroke for the pistons ... 0 20' 0 10'
(15) Screw to make the adjustment for the maximum stroke for the pistons.
NOTE: Some pumps use shims under a bolt (head) to make the adjustment for maximum
piston stroke.
(17) 8J1898 Shims to make the adjustment for the minimum stroke for the pistons.
(20) 8J8462 Shim to make the adjustment for the pressure of the oil to move the shuttle valve.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 6/7/2017
16G MOTOR GRADER 93U01179-02678 (MACHINE) POWERED BY 3406 ENGINE(... Page 6 of 6
(23) 8J5835 Spacer to make the adjustment for the maximum discharge pressure.
Copyright 1993 - 2017 Caterpillar Inc. Wed Jun 7 09:15:19 UTC+0200 2017
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/p... 6/7/2017