Yamaha Rx-A3030 PDF

AV RECEIVER
RX-A3030/RX-V3075
RX-A3030/RX-V3075 SERVICE MANUAL
Note: When the DIGITAL P.C.B. or IC78 on DIGITAL (1) P.C.B. is replaced, this unit will display Internal Error and
will not operate properly. The model name MUST be written to the backup IC (EEPROM: IC78 on DIGITAL (1)
P.C.B.) to have proper operation. (For detailed procedure, refer to related Service News or Service Bulletin.
Or contact your local Yamaha representative.)
DIGITAL P.C.B. DIGITAL1P.C.B. IC78 Internal Error
ICEEPROMDIGITAL1P.C.B.
IC78

IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known
and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury,
destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise
all Yamaha product owners that any service required should be performed by an authorized Yamaha Retailer or the
appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service
departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and specifications
are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's
Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
CONTENTS
TO SERVICE PERSONNEL ............................................2 DISPLAY DATA .......................................................8385
FRONT PANELS .............................................................3 IC DATA ................................................................. 86108
REAR PANELS ...........................................................47 PIN CONNECTION DIAGRAMS ................................. 109
REMOTE CONTROL PANEL ..........................................8 BLOCK DIAGRAMS .............................................110113
SPECIFICATIONS / ................................... 916 WIRING DIAGRAMS ............................................114115
INTERNAL VIEW .......................................................... 17 PRINTED CIRCUIT BOARDS ............................. 116144
SERVICE PRECAUTIONS / ..... 17 SCHEMATIC DIAGRAMS ................................... 145165
DISASSEMBLY PROCEDURES / ........... 1822 REPLACEMENT PARTS LIST ............................167200
UPDATING FIRMWARE / REMOTE CONTROL ........................................... 201203
............................2325 CONFIGURING THE SYSTEM SETTINGS .................204
SELF-DIAGNOSTIC FUNCTION / .....................................205206
.....................................2680 FIRMWARE UPDATING PROCEDURE .............. 207218
POWER AMPLIFIER ADJUSTMENT / ..................................... 219224
.................................................8182
Copyright (c) Yamaha Corporation All rights reserved.

101272 This manual is copyrighted by Yamaha and may not be copied or
redistributed either in print or electronically without permission.
P.O.Box 1, Hamamatsu, Japan
'13.08
RX-A3030/RX-V3075
TO SERVICE PERSONNEL AC LEAKAGE

1. Critical Components Information WALL EQUIPMENT TESTER OR
OUTLET UNDER TEST EQUIVALENT
RX-A3030/RX-V3075
Components having special characteristics are marked and

must be replaced with parts having specifications equal to those
originally installed.
2. Leakage Current Measurement (For 120V Models Only)
When service has been completed, it is imperative to verify
INSULATING
that all exposed conductive surfaces are properly insulated TABLE
from supply circuits.
Meter impedance should be equivalent to 1500 ohms shunted Leakage current must not exceed 0.5mA.
by 0.15 F. Be sure to test for leakage with the AC plug in both polarities.
For U model
CAUTION
F2001: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 2A,
250V FUSE.
F2002: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A,
125V FUSE.
For C model
CAUTION
F2001: REPLACE WITH SAME TYPE 2A, 250V FUSE.
F2002: REPLACE WITH SAME TYPE 10A, 125V FUSE.
ATTENTION
F2001: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 2A, 250V.
F2002: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 10A, 125V.
WARNING: CHEMICAL CONTENT NOTICE!

This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive
harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON
WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or
expose eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
About lead free solder /

All of the P.C.B.s installed in this unit and solder joints are
soldered using the lead free solder.
Among some types of lead free solder currently available,
it is recommended to use one of the following types for
the repair work. Sn+Ag+Cu + +
Sn + Ag + Cu (tin + silver + copper) Sn+Cu +
Sn + Cu (tin + copper) Sn+Zn+Bi + +
Sn + Zn + Bi (tin + zinc + bismuth)

Caution: 30
As the melting point temperature of the lead free solder 40
is about 30C to 40C (50F to 70F) higher than that of
the lead solder, be sure to use a soldering iron suitable
to each solder.
2
RX-A3030/RX-V3075
FRONT PANELS
RX-A3030 (U, C, R, T, K, A, B, G, F, L, S, J models)
RX-A3030/RX-V3075
U model
C, R, T, K, A, B, G, F, L, S models
J model
RX-V3075 (T, A models)
3
RX-A3030/RX-V3075
REAR PANELS
RX-A3030 (U model)
RX-A3030/RX-V3075
RX-A3030 (C model)
RX-A3030 (R, S models)
4
RX-A3030/RX-V3075
RX-A3030 (T model)
RX-A3030/RX-V3075
RX-A3030 (K model)
RX-A3030 (A model)
5
RX-A3030/RX-V3075
RX-A3030 (B, G, F models)

RX-A3030/RX-V3075
RX-A3030 (L model)
RX-A3030 (J model)
6
RX-A3030/RX-V3075
RX-V3075 (T model)
RX-A3030/RX-V3075
RX-V3075 (A model)
7
RX-A3030/RX-V3075
REMOTE CONTROL PANEL

RAV423
RX-A3030/RX-V3075
Inside of the remote control cover

8
RX-A3030/RX-V3075
SPECIFICATIONS /
Audio Section /
RX-A3030/RX-V3075
Rated Output Power (Power Amp. Section) / Damping Factor / (1 kHz, 8 ohms)
FRONT L/R to SPEAKER-A ............................................ 150 or more
(1 kHz, 0.9 % THD) Frequency Response / (10 Hz to 100 kHz)
1 channel driven AUDIO2, etc. (Pure Direct) ..................................................0 / -3 dB
U, C, R, T, K, A, B, G, F, L, S models (8 ohms) RIAA Equalization Deviation / RIAA (20 Hz to 20 kHz)
FRONT L/R ................................................................ 185 W/ch PHONO (MM) ................................................................... 0 0.5 dB
CENTER .......................................................................... 185 W
SURROUND L/R ........................................................ 185 W/ch Signal to Noise Ratio / (IHF-A network)
SURROUND BACK L/R ............................................. 185 W/ch PHONO (MM) to AV OUT
FRONT PRESENCE L/R ............................................. 185 W/ch U, C, R, T, S models (Input shorted 5 mV) .............. 86 dB or more
B, G, F models (4 ohms) K, A, B, G, F, L models (Input shorted 5 mV) .......... 81 dB or more
FRONT L/R ................................................................ 230 W/ch J model (Input shorted 2.5 mV) .............................. 80 dB or more
J model (6 ohms) AUDIO2, etc. (Pure Direct) to SP OUT (Input shorted 250 mV)
FRONT L/R ................................................................ 200 W/ch .............................................................................. 100 dB or more
CENTER .......................................................................... 200 W
Residual Noise / (IHF-A Network)
SURROUND L/R ........................................................ 200 W/ch
FRONT L/R to SP OUT ................................................150 V or less
SURROUND BACK L/R ............................................. 200 W/ch
FRONT PRESENCE L/R ............................................. 200 W/ch Channel Separation / (1 kHz / 10 kHz)
2 channels driven simultaneously PHONO (MM) (Input shorted)
U, C, R, T, K, A, B, G, F, L, S models (8 ohms) ...................................................... 60 dB or more / 55 dB or more
FRONT L/R .......................................................165 W + 165 W AUDIO2, etc. (Input 5.1 k-ohms shorted)
CENTER .......................................................................... 165 W ...................................................... 60 dB or more / 45 dB or more
SURROUND L/R ...............................................165 W + 165 W
Input Sensitivity/Input Impedance /
SURROUND BACK L/R ....................................165 W + 165 W
(1 kHz, 100 W/8 ohms)
FRONT PRESENCE L/R ....................................165 W + 165 W
PHONO (MM) .................................................... 3.5 mV / 47 k-ohms
(20 Hz to 20 kHz, 0.06 % THD)
AUDIO2, etc. .................................................... 200 mV / 47 k-ohms
2 channels driven simultaneously
U, C, R, T, K, A, B, G, F, L, S models (8 ohms) Maximum Input Signal / (1 kHz, 0.5 % THD)
FRONT L/R .......................................................150 W + 150 W PHONO (MM) ............................................................60 mV or more
CENTER .......................................................................... 150 W
AUDIO2, etc. ...............................................................2.4 V or more
SURROUND L/R ...............................................150 W + 150 W
SURROUND BACK L/R ....................................150 W + 150 W Output Level/Output Impedance /
FRONT PRESENCE L/R ....................................150 W + 150 W AV OUT ............................................................ 200 mV / 1.2 k-ohms
J model (6 ohms) HEADPHONE OUT ............................................ 150 mV / 100 ohms
FRONT L/R .......................................................150 W + 150 W
PRE OUT
CENTER .......................................................................... 150 W
1 kHz (FRONT, CENTER, SURROUND, SURROUND BACK)
SURROUND L/R ...............................................150 W + 150 W
.......................................................................... 1 V / 1.2 k-ohms
SURROUND BACK L/R ....................................150 W + 150 W
50 Hz (SUBWOOFER) ......................................... 1 V / 1.2 k-ohms
FRONT PRESENCE L/R ....................................150 W + 150 W
ZONE OUT .............................................................. 1 V / 1.2 k-ohms
Dynamic Power Per Channel (IHF)
[U, C, R, T, K, A, B, G, F, L, S models] Volume Control Range/Step /
Main ZONE, ZONE2, ZONE3
FRONT L/R (1 channel driven)
...................................... MUTE / -80 dB to +16.5 dB / 0.5 dB step
(8 / 6 / 4 / 2 ohms) ..................................... 175 / 220 / 295 / 410 W
Tone Control Characteristics /
Maximum Effective Output Power / (JEITA)
(1 channel driven / 1 kHz, 10 % THD) [R, T, K, L, S, J models] Main ZONE
Bass
R, T, K, L, S models (8 ohms)
Boost/Cut ...................................... 6 dB / 0.5 dB step, at 50 Hz
FRONT L/R ...................................................................... 230 W/ch
Turnover frequency .......................................................... 350 Hz
CENTER ............................................................................... 230 W
SURROUND L/R .............................................................. 230 W/ch Treble
SURROUND BACK L/R ................................................... 230 W/ch Boost/Cut .....................................6 dB / 0.5 dB step, at 20 kHz
FRONT PRESENCE L/R .................................................. 230 W/ch Turnover frequency ......................................................... 3.5 kHz
J model (6 ohms) ZONE2, ZONE3
FRONT L/R ...................................................................... 230 W/ch Bass
CENTER ............................................................................... 230 W Boost/Cut ....................................... 10 dB / 2 dB step, at 50 Hz
SURROUND L/R .............................................................. 230 W/ch Turnover frequency .......................................................... 350 Hz
SURROUND BACK L/R ................................................... 230 W/ch Treble
FRONT PRESENCE L/R .................................................. 230 W/ch Boost/Cut ....................................... 10 dB / 2 dB step, at 50 Hz
Turnover frequency ......................................................... 3.5 kHz
Total Harmonic Distortion / (20 Hz to 20 kHz)
PHONO (MM) to AV OUT ............................................0.02 % or less
Multi channel input (Pure Direct) to SP OUT (70 W/8 ohms)
.................................................................................0.04 % or less
9
RX-A3030/RX-V3075
RX-A3030/RX-V3075
Bass Crossover Frequency / Signal to Noise Ratio / (IHF)

FRONT, CENTER, SURROUND, SURROUND BACK small (H.P.F.) U model
.................... fc=40/60/80/90/100/110/120/160/200 Hz, 12 dB/oct. HD Radio ...............................................................................80 dB
SUBWOOFER small (L.P.F.) C, R, T, K, A, B, G, F, L, S, J models
.................... fc=40/60/80/90/100/110/120/160/200 Hz, 24 dB/oct. Mono / Stereo ........................................................... 72 dB / 70 dB
Optical Jack, Coaxial Jack Support Frequencies / Harmonic Distortion / (1 kHz)

Optical Coaxial fs U model
............................................................................... 32 kHz to 96 kHz HD Radio ............................................................................. 0.03 %
C, R, T, K, A, B, G, F, L, S, J models
Video Section / Mono / Stereo ............................................................ 0.3 % / 0.5 %
Video Signal Type / Antenna Input /

....................................................................... 75 ohms unbalanced
Monitor / ZONE out (Wall paper / GUI) /
ZONE GUI
U, C, R, K, S, J models ................................................NTSC / PAL AM Section / AM
T, A, B, G, F, L models ..................................................PAL / NTSC
Tuning Range /
Video conversion / GUI / GUI
.....................................................................................NTSC / PAL U, C models ........................................................... 530 to 1,710 kHz
R, L, S models ......................... 530 to 1,710 kHz / 531 to 1,611 kHz
Video Signal Level /
T, K, A, B, G, F, J models ....................................... 531 to 1,611 kHz
Composite Video Signal /
............................................................................1 Vp-p / 75 ohms Antenna /
S-Video Signal / S ..................................................................................... Loop antenna
Y ..........................................................................1 Vp-p / 75 ohms
C General /
U, C, R, K, S, J models (NTSC) .................0.286 Vp-p / 75 ohms
Power Supply /
T, A, B, G, F, L models (PAL) .........................0.3 Vp-p / 75 ohms
U, C models ............................................................ AC 120 V, 60 Hz
Component Video Signal /
R, S models .................................AC 110120/220240 V, 50/60 Hz
Y ..........................................................................1 Vp-p / 75 ohms
T model ................................................................... AC 220 V, 50 Hz
Pb/Pr ................................................................0.7 Vp-p / 75 ohms
K model .................................................................. AC 220 V, 60 Hz
D Video Signal / D [J model]
A model .................................................................. AC 240 V, 50 Hz
Y ..........................................................................1 Vp-p / 75 ohms
B, G, F models ........................................................ AC 230 V, 50 Hz
Pb/Pr ................................................................0.7 Vp-p / 75 ohms
L model ...................................................... AC 220240 V, 50/60 Hz
Video Maximum Input Level /
J model .............................................................. AC 100 V, 50/60 Hz
(VIDEO Conversion Off)
............................................................................... 1.5 Vp-p or more Voltage Selector [R, S models]
...........................................................110120 V / 220240 V select
Video Signal to Noise Ratio /
(VIDEO Conversion Off) Power Consumption /
................................................................................... 60 dB or more
U model ....................................................................490 W / 620 VA
Monitor/ZONE Out Frequency Response / C model ....................................................................400 W / 510 VA
ZONE
R, T, A, B, G, F, L, S models .................................................... 490 W
(VIDEO Conversion Off)
K model .................................................................................. 390 W
Component video signal /
.................................................................5 Hz to 100 MHz, 3 dB J model ................................................................................... 280 W
D video signal / D [J model] Standby Power Consumption (reference data) /

.................................................................5 Hz to 100 MHz, 3 dB
HDMI control: OFF / Standby through: OFF
FM Section / FM ................................................................................ 0.3 W (typical)
HDMI control: ON / Standby through: ON
Tuning Range / ................................................................................ 5.0 W (typical)
U, C models ......................................................... 87.5 to 107.9 MHz HDMI control: OFF / Standby through: ON
R, L, S models .................87.5 to 108.0 MHz / 87.50 to 108.00 MHz INPUT: AV1 (HDMI no signal)
T, K, A, B, G, F models .................................... 87.50 to 108.00 MHz ............................................................................. 4.2 W (typical)
J model .................................................................. 76.0 to 90.0 MHz Network standby: ON

................................................................................ 2.2 W (typical)
50 dB Quieting Sensitivity / 50 dB SN (IHF)
(1 kHz, 100 % MOD.) Maximum Power Consumption [R, L, S models]
Mono ......................................................................... 3 V (20.8 dBf) (10 % THD, All channel driven)
............................................................................................. 1,210 W
10
RX-A3030/RX-V3075
RX-A3030/RX-V3075
Dimensions (W x H x D) /
[RX-A3030]
............................ 435 x 192 x 467 mm (17-1/8" x 7-1/2" x 18-3/8") DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered
trademarks & DTS-HD Master Audio is a trademark of DTS, Inc.
[RX-V3075] Product includes software. DTS, Inc. All Rights Reserved.
............................ 435 x 182 x 465 mm (17-1/8" x 7-1/8" x 18-3/8")
DTS-HD DTS DTS-HD Master Audio
Weight / DTS DTS
[RX-A3030]
U, C, R, K, A, L, S models .................................. 18.2 kg (40.1 lbs.)
T, B, G, F, J models ........................................... 19.9 kg (43.9 lbs.)
[RX-V3075]
AirPlay, iPad, iPhone, iPod, iPod nano, and iPod touch are trademarks of
T model .............................................................. 19.5 kg (43.0 lbs.) Apple Inc., registered in the U.S. and other countries.
A model ............................................................. 17.8 kg (39.2 lbs.) AirPlayiPadiPhoneiPodiPod nanoiPod touchSafari
Apple Inc.
Finish /
[RX-A3030]
T model ...........................................................................Gold color
U, C, R, T, K, A, B, G, F, L, S, J models ........................ Black color
R, B, G, F, L models ..................................................Titanium color
[RX-V3075] MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and
T model ..........................................................................Gold color Thomson.
MPEG Layer 3 Fraunhofer IIS Thomson
T, A models .................................................................. Black color

Accessories /
Remote control ..............................................................................x 1
Battery (R03, AAA, UM-4) .............................................................x 4
FM antenna (1.4 m) .....................................................................x 1
This receiver supports network connections.
AM antenna (1.2 m) (U model) ....................................................x 1

(1.0 m) (C, R, T, K, A, B, G, F, L, S, J models) ........x 1
YPAO microphone (6.0 m) ............................................................x 1
Microphone base ..........................................................................x 1
Antenna isolator (T model) ...........................................................x 1
HD Radio Technology manufactured under license from iBiquity Digital
Conversion plug (T model) ...........................................................x 1 Corporation. U.S. and Foreign Patents. HD Radio and the HD, HD Radio,
and Arc logos are proprietary trademarks of iBiquity Digital Corp.
Power cable (2.0 m) (U, C, R, T, K, A, B, G, F, S, J models) ........x 1
(L model) ....................................................x 2
* Specifications are subject to change without notice. HDMI, the HDMI Logo, and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC in the United
States and other countries.
HDMIHDMI High-Denition Multimedia Interface
HDMI Licensing LLC
U .......................U.S.A. model B ......................British model
C .................Canadian model G .................European model
R ....................General model F .................... Russian model
T .................... Chinese model L .................Singapore model
K ..................... Korean model S .................. Brazilian model MHL and the MHL logo are a trademark, registered trademark or service
A ................Australian model J .................. Japanese model mark of MHL, LLC in the United States and/or other countries.
MHLMHL Mobile High-Denition Link
MHL, LLC
x.v.Color is a trademark of Sony Corporation.

x.v.Color
Manufactured under license from Dolby Laboratories. Dolby, Pro Logic,
Surround EX and the double-D symbol are trademarks of Dolby Laboratories.
Dolby
Pro LogicSurround EX D
SILENT CINEMA is a trademark of Yamaha Corporation.
SILENT CINEMA
11
RX-A3030/RX-V3075
RX-A3030/RX-V3075
Android is a trademark of Google Inc.
DLNA and DLNA CERTIFIED are trademarks or registered trademarks Android Google Inc.
of Digital Living Network Alliance. All rights reserved. Unauthorized use is
strictly prohibited.
DLNA DLNA CERTIFIED
This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights. Use of this copyright
protection technology must be authorized by Rovi Corporation, and is
intended for home and other limited viewing uses only unless otherwise
authorized by Rovi Corporation. Reverse engineering or disassembly is
Windows is a registered trademark of Microsoft Corporation in the United
prohibited.
States and other countries.
Windows Microsoft Corporation

Internet Explorer, Windows Media Audio and Windows Media Player are AAC
either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Internet ExplorerWindows Media AudioWindows Media Player
Microsoft Corporation

DIMENSIONS /
RX-A3030 RX-V3075
Top view Top view
(2-3/8")
(2-3/8")
(1")
(1")
27
25
60 60
62
62
298 (11-3/4")
298 (11-3/4")
418 (16-1/2")
467 (18-3/8")
418 (16-1/2")
465 (18-1/4")
48/18
58
(2-1/4")
58
(2-1/4")
50 335 (13-1/4") 50 335 (13-1/4")

22
(7/8")
22
(7/8")
(2") (2")
Front view Front view

171 (6-3/4")
161 (6-3/8")
192 (7-1/2")
182 (7-1/8")
21
(7/8")
21
(7/8")
435 (17-1/8") 435 (17-1/8")
Unit: mm (inch) Unit: mm (inch)

12 mm
RX-A3030/RX-V3075
SELECT MENU
RX-A3030/RX-V3075
Sound field parameters
Surround Back Initial Delay: 1 to 49 ms
Surround Back Room Size: 0.1 to 2.0

Surround Initial Delay: 1 to 49 ms
Surround Back Liveness: 0 to 10
Front/Rear Balance: -5 to +5, [0]

Parameter
Surround Room Size: 0.1 to 2.0
Left/Right Balance: -5 to +5, [0]
Monaural Mix: Off / On, [Off]

Height Balance: 0 to 10, [5]
Surround Liveness: 0 to 10
DSP Level: -6 to +3 dB, [0]
Reverb Delay: 0 to 250 ms
Reverb Level: 0 to 100 %

Reverb Time: 1.0 to 5.0 s
Initial Delay: 1 to 99 ms
Direct: Auto / Off, [Auto]

Room Size: 0.1 to 2.0
Level: -5 to +5, [0]

Decode Type (*1)
Liveness: 0 to 10
Reset
Category Program
MOVIE THEATER Standard
Spectacle
Sci-Fi
Adventure
Drama
Mono Movie
ENTERTAINMENT Sports
Action Game
Roleplaying Game
Music Video
Recital/Opera
CLASSICAL Hall in Munich
Hall in Vienna
Hall in Amsterdam
Church in Freiburg
Church in Royaumont
Chamber
LIVE/CLUB Village Vanguard
Warehouse Loft
Cellar Club
The Roxy Theatre
The Bottom Line
STEREO 2ch Stereo
9ch Stereo
SUR. DECODE SURROUND DECODER
*1
STRAIGHT
*1 Surround Decoder Panorama Center Width Dimension Center Image

Off / On, [Off] 0 to 7, [3] -3 to +3, [0] 0.0 to 1.0, [0.3]
Pro Logic
PL IIx Movie / PL II Movie
PL IIx Music /
Decode Type PL II Music
PL IIx Game / PL II Game
Neo:6 Cinema
Neo:6 Music
13
RX-A3030/RX-V3075
SET MENU TABLE /

RX-A3030/RX-V3075
MAIN MENU SUB-MENU PARAMETER VALUE [INITIAL VALUE]
Speaker Auto Measure Optimizes the speaker configuration automatically using YPAO.
Setup Multi Position Yes / No
Angle Yes / No
Result Not Available
Manual Setting Pattern [Pattern1] / Pattern2 * Select ENTER
Setting Data Copy Pattern1 2 / Pattern2 1 * Select ENTER
Power Amp Assign [Basic] / 7ch +1ZONE / 9ch +1ZONE / 7ch +2ZONE /
9ch +RP / 9ch +FRONT / 7ch +FP +RP /
7ch +FRONT +1ZONE / 5ch +FRONT +2ZONE / 7ch BI-AMP /
7ch BI-AMP +1ZONE / 7ch BI-AMP +FP +RP
* Select ENTER
EXTRA SP 1 / 2 Zone 2 / Zone 3
* When Power Amp Assign is set to Basic / 9ch +RP / 9ch

+FRONT / 7ch +FP +RP / 7ch BI-AMP, this setup is disabled.
Configuration Front Large / [Small]
* When Subwoofer1/2 is set to None, Front is disabled.
Center
Large / [Small] / None
Surround
Surround Back Large x1 / Large x2 / Small x1 / [Small x2] / None
* When Surround is set to None, Surround Back is disabled.
Crossover 40 / 60 / [80] / 90 / 100 / 110 / 120 / 160 / 200 Hz
* When Front / Center / Surround / Surround Back is set to

Small, this setup is enabled.
Front Presence [Use] / None
Rear Presence Use / [None]
Subwoofer 1, Subwoofer 2 [Use] / None
Select Use [Normal] / Reverse
SWFR Layout Left + Right / Front + Rear / [Monaural x2]
* When Subwoofer1/2 is set to None, SWFR Layout is disabled.
Extra Bass [Off] / On
* When Front is set to Large, Extra Bass is disabled.
Distance Meter / Feet
Front L, Front R,
Center,
Surround L, Surround R,
0.30 to 24.00 m, [3.00 m], 0.05 m step
Surround Back L, Surround Back R,
1.0 to 80.0 ft, [10.0 ft], 0.2 ft step
Front Presence L, Front Presence R,
Rear Presence L, Rear Presence R,
Subwoofer 1, Subwoofer 2
Level Front L, Front R,
Center,
Surround Back L, Surround Back R, -10.0 to +10.0 dB, [0.0 dB], 0.5 dB step
Front Presence L, Front Presence R,
Rear Presence L, Rear Presence R,
Subwoofer 1, Subwoofer 2
14
RX-A3030/RX-V3075
RX-A3030/RX-V3075
Speaker Manual Parametric EQ Manual / YPAO : Flat / YPAO : Front / YPAO : Natural / [Through]
Setup * Select ENTER
Front L, Front R, Band Band: #1 to #7

Center, / Gain Gain: -20.0 to +6.0 dB, [0.0 dB], 0.5 dB step
Surround Back L,
Surround Back R, Frequency Frequency: 31.3 Hz to 16.0 kHz, [62.5 Hz]

Front Presence L, / Gain Gain: -20.0 to +6.0 dB, [0.0 dB], 0.5 dB step
Front Presence R,
Rear Presence L,
Rear Presence R, Q Q: 0.500 to 10.080, [1.000]

Subwoofer 1, / Gain Gain: -20.0 to +6.0 dB, [0.0 dB], 0.5 dB step
Subwoofer 2
* When Parametric EQ is set to Through, this setup is enabled.
PEQ Data Copy Flat Manual / Front Manual / Natural Manual
* When Parametric EQ is set to Manual, PEQ Data Copy is

enabled.
PEQ Data Clear OK / CANCEL
* When Parametric EQ is set to Manual, PEQ Data Clear is

enabled.
Test Tone [Off] / On
Sound Setup Lipsync Delay Enable AV1 / AV2 / AV3 / AV4 / AV5 / AV6 / AV7 / Disable / [Enable]
V-AUX / AUDIO1 / AUDIO2 / AUDIO3 / AUDIO4
Auto/Manual Select [Auto] / Manual
Adjustment 0 to 500 ms, [0 ms], 1 ms step
Dynamic Range [Maximum] / Standard / Minimum/Auto
Max. Volume -30.0 to +16.5 dB (Maximum volume), [+16.5 dB], 5.0 dB step
Initial Volume [Off] / On
Select On Mute, -80 to +16.5 dB, [-40.0 dB], 0.5 dB step
Pure Direct Mode [Auto] / Video Off
Adaptive DSP Level Off / [On]
VPS (Virtual Presence Speaker) Off / [On]
Video Setup Analog to Analog Conversion Off / [On]
Video Mode [Direct] / Processing
Select Resolution Through / [Auto] / 576p / 720p / 1080i / 1080p / 4K
Processing * Select ENTER
Aspect [Through] / 16:9 Normal
Adjustment Preset Detail Enhancement 0 to 50, [0], 1 step

1 Edge Enhancement
to Brightness
Preset Contrast -100 to +100, [0], 1 step

6 Saturation
HDMI Setup HDMI Control [Off] / On
Select On TV Audio Input [AUDIO 1] / AUDIO 2 / AUDIO 3 / AUDIO 4
ARC (Audio Return Channel) Off / [On]
Standby Sync Off / On / [Auto]
15
RX-A3030/RX-V3075
RX-A3030/RX-V3075

HDMI Setup Audio Output Amp Off / [On]
HDMI OUT1, HDMI OUT2 [Off] / On
Standby Through [Off] / On
* When HDMI Control is set to On, Standby Through is disabled.
Network IP Address DHCP Off / [On]
Setup IP Address xxx.xxx.xxx. x
Subnet Mask xxx.xxx.xxx. x
Default Gateway xxx.xxx.xxx. x
DNS Server (P) Primary x. x. x. x
DNS Server (S) Secondary x. x. x. x
Network Standby [Off] / On
MAC Address Filter [Off] / On
Filter MAC Address 15, 610 xx : xx : xx : xx : xx : xx
Network Name Input is possible to 15 characters
Multi Zone Main Zone Set Zone Rename Input is possible to 9 characters
Setup Zone2, Zone3 Volume Fixed / [Variable]
Set Max. Volume -30.0 to +16.5 dB (Maximum volume), [+16.5 dB], 5.0 dB step
Initial Volume [Off] / On
Select On Mute, -80 to +16.5 dB, 0.5 dB step
Mono [Off] / On
Zone Scene Rename SCENE14 Input is possible to 20 characters
Zone Rename Input is possible to 9 characters
Zone4 Set Zone Scene Rename SCENE14 Input is possible to 20 characters
Zone Rename Input is possible to 9 characters
Monitor Out Assign [Main] / Zone2 / Zone3
HDMI Out2 Assign [Main] / Zone2 (Audio Output: Off) / Zone4
Party Mode Set Target: Zone2, Target: Zone3, Target: Zone4 Disable / [Enable]
Function Input Assignment Coaxial ,, None /
Setup Optical ,, AV1 / AV2 / AV3 / AV4 / AV5 / AV6 / AV7 /
Component , , , AUDIO1 / AUDIO2 / AUDIO3 / AUDIO4 * Select ENTER
Display Set Dimmer (Front Display) -4 to 0 (higher to brighten), [0]
Short Message [On] / Off
Wallpaper Picture1 / Picture2 / Picture3 / Gray
Trigger Trigger Mode [Power] / Source / Manual
Output1 Select Source AV17, V-AUX, AUDIO14, PHONO, TUNER, Rhapsody,
Pandora, AirPlay, SERVER, NET RADIO, USB, MULTI CH
Trigger Low / [High]
Output2 Select Manual Low / [High]
Target Zone Main / Zone 2 / Zone 3 / Zone 4 / [All]
DC OUT Power Mode [Continuous] / Main Zone Power Sync.
Memory Guard [Off] / On
ECO Setup Auto Power Standby Off / 2 Hours / 4 Hours / 8 Hours / 12 Hours
U, C, R, T, K, A, L, S, J models: [Off]
B, G, F models: [8 Hours]
ECO Mode [Off] / On
Language [English (English)] / (Japanese) / Franais (French) /
Setup Deutsch (German) / Espaol (Spanish) / ycc (Russian) /
Italiano (Italian) / (Chinese) * Select ENTER
16
RX-A3030/RX-V3075
INTERNAL VIEW
Rear view 1 2
1 VIDEO (1) P.C.B.
RX-A3030/RX-V3075
2 AMPPOWER (3) P.C.B. (R, S models)
3 AMPPOWER (2) P.C.B.
4 AMP (3) P.C.B.
5 HD RADIO TUNER (U model)
AM/FM TUNER (C, R, T, K, A, B, G, F, L, S, J models)
6 FUNCTION (3) P.C.B.
7 6 5 4 3 7 FUNCTION (1) P.C.B.
8 9 10 11 12 13 8 POWER P.C.B. (U, C, R, K, A, B, G, F, L, S, J models)
POWER2 (1) P.C.B. (T model)
Top view
9 DIGITAL (3) P.C.B.
12 FUNCTION (5) P.C.B. (U model)
13 FUNCTION (2) P.C.B.
14 AMP (2) P.C.B.
16 AMP (5) P.C.B.
17 POWER TRANSFORMER
18 VIDEO (3) P.C.B.
19 AMP (4) P.C.B.
21 AMP (1) P.C.B.
22 OPERATION (1) P.C.B.
21 20 19 18 17 16 15 14
Front view 22 23
26 25 24
SERVICE PRECAUTIONS /
Safety measures
Some internal parts in this product contain high voltages
and are dangerous.
Be sure to take safety measures during servicing, such
as wearing insulating gloves.
Note that the capacitors indicated below are dangerous OFF
even after the power is turned off because an electric
charge remains and a high voltage continues to exist 5 k /10 W
there.
Before starting any repair work, connect a discharging 30
resistor (5 k-ohms/10 W) to the terminals of each MAIN3P.C.B. C1105C1106
capacitor indicated below to discharge electricity.
POWER21P.C.B. C2016
The time required for discharging is about 30 seconds
per each. PRINTED CIRCUIT BOARDS

C1105 and C1106 on MAIN (3) P.C.B.
C2016 on POWER2 (1) P.C.B.
For details, refer to PRINTED CIRCUIT BOARDS. 17
RX-A3030/RX-V3075
DISASSEMBLY PROCEDURES /
(Remove parts in the order as numbered.)
RX-A3030/RX-V3075
Disconnect the power cable from the AC outlet. AC
1. Removal of Top Cover 1.

a. Remove 4 screws (), 4 screws () and 2 screws (). a. 4 4 2
(Fig. 1) Fig. 1
b. Lift the rear of the top cover to remove it. (Fig. 1) b. Fig. 1
2. Removal of Front Panel Unit 2.

and Sub-chassis Unit
a. Remove 6 screws () and then remove the front a. 6
panel unit forward. (Fig. 1) Fig. 1
b. Remove 4 push rivets and then remove the side plate b. 4 L
(L) and the side plate (R). (Fig. 1) RFig. 1
c. Remove 2 screws (), 2 screws (), 3 screws () c. 2 2 3
and screw (). (Fig. 1) 1 Fig. 1
d. Remove CB9 CB11 CB77, CB361, CB454, CB737, d. CB9 CB11CB77CB361CB454CB737
CB931 and CB952. (Fig. 1) CB931CB952 Fig. 1
e. Release 2 hooks and then remove the sub-chassis e. 2
unit. (Fig. 1) Fig. 1
Top cover
DIGITAL (1) P.C.B.
CB952
CB10
FUNCTION (2) P.C.B.
CB11 CB9

CB931 CB77
CB737
Push rivet

CB361 CB454 VIDEO (3) P.C.B.
OPERATION (2) P.C.B. Push rivet

Side plate (L)
L

Hook

Push rivet
Hook

Sub-chassis unit

Side plate (R) Push rivet
R
Front panel unit

18 Fig. 1
RX-A3030/RX-V3075
3. Removal of DIGITAL (1) P.C.B. 3. DIGITAL1P.C.B.
RX-A3030/RX-V3075
a. Remove 3 screws (). (Fig. 2) a. 3 Fig. 2
b. Remove 10 screws () and screw (). (Fig. 3) b. 10 1 Fig. 3
c. Remove CB21, CB22, CB70, CB71, CB73 CB76, c. CB21CB22CB70CB71CB73 CB76CB81
CB81, CB923, CB924, CB930 and CB942. (Fig. 2) CB923CB924CB930CB942 Fig. 2
d. Remove CB943, CB944 and CB945 and then remove d. CB943CB944CB945 DIGITAL1P.C.B.
the DIGITAL (1) P.C.B. which is connected directly to the
FUNCTION (2) P.C.B. with board-to-board connectors. DIGITAL1P.C.B. FUNCTION2P.C.B.
(Fig. 2)
Fig. 2
CB22
CB21
CB71
DIGITAL (1) P.C.B.
CB70
CB942 CB943
CB930
CB924 CB944
CB75
CB73
CB74 Board-to-board connectors
CB81
CB76 CB923 CB945
Board-to-board connectors

CB736

CB733
CB731
FUNCTION (2) P.C.B.
Fig. 2

Rear view
Fig. 3
19
RX-A3030/RX-V3075
4. Removal of VIDEO (1) P.C.B. 4. VIDEO1P.C.B.

RX-A3030/RX-V3075
a. Remove 11 screws (). (Fig. 4) a. 12 Fig. 4

b. Remove CB304, CB331, CB333 (U model) and CB334 b. CB304CB331
Fig. 5
(U model). (Fig. 5) c. 2 VIDEO1P.C.B.
c. Release 2 hooks and then remove the VIDEO (1) P.C.B. Fig. 5
(Fig. 5)
5. Removal of FUNCTION (1)(3) P.C.B.s 5. FUNCTION13P.C.B.

a. Remove screw (). (Fig. 5) a. 1 Fig. 5
b. Remove 18 screws (). (Fig. 4) b. 18 Fig. 4
c. Remove CB112, CB113 and CB709 (C, R, T, K, A, B, G, c. CB112CB113CB709 Fig. 5
F, L, S models). (Fig. 5) d. 1 FUNCTION1P.C.B.
d. Release hook and then remove the FUNCTION (1) FUNCTION2
3P.C.B. Fig. 5
P.C.B. together with the FUNCTION (2) and (3) P.C.B.s.
(Fig. 5)
J model Rear view
Hook

Fig. 4
CB331
CB334 VIDEO (1) P.C.B.
(U model) CB333 CB304
(U model)
FUNCTION (1) P.C.B.

FUNCTION (2) P.C.B.
CB113 Hook
AMP (1) P.C.B.
CB709
(C, R, T, K, A, B,
G, F, L, S, J models)
AMP (2) P.C.B.

CB112 FUNCTION (3) P.C.B.
Fig. 5
20
RX-A3030/RX-V3075
When checking the P.C.B.: P.C.B.
RX-A3030/RX-V3075
Put the rubber sheet and the cloth over this unit, and
place the sub-chassis unit on them as shown below. Fig. 6
(Fig. 6) LR
Connect the heatsink of the AMP unit (L) and the
AMP unit (R) to the chassis with a ground lead. (Fig. 6) Fig. 6
Reconnect all cables (connectors) that have been
disconnected.
When connecting the flexible flat cable, be careful
with polarity.
Sub-chassis unit AMP unit (R)

R
Rubber sheet and cloth
AMP unit (L)

L
Ground lead
Chassis
Ground lead

Fig. 6
21
RX-A3030/RX-V3075
When checking the DIGITAL (1) P.C.B.: DIGITAL1P.C.B.

RX-A3030/RX-V3075
Put the rubber sheet and cloth over this unit, and DIGITAL
place the DIGITAL (1) P.C.B. on them. (Fig. 7) 1P.C.B.
Fig. 7
Connect ST951 on DIGITAL (1) P.C.B. to the chassis DIGITAL1P.C.B. ST951
with a ground lead. (Fig. 7) Fig. 7
Reconnect all cables (connectors) that have been
disconnected. Be sure to use the P.C.B. CHECKING
JIG (Part No. ZF906400) to connect between the P.C.B. : ZF906400
following connectors.
CB943 on DIGITAL (1) P.C.B. DIGITAL1P.C.B. CB943
CB731 on FUNCTION (2) P.C.B. FUNCTION2P.C.B. CB731

When connecting the flexible flat cable, be careful
with polarity.
DIGITAL (1) P.C.B.
P.C.B. CHECKING JIG

P.C.B.
FUNCTION (2) P.C.B.

CB945
CB944
CB943
Rubber sheet and cloth CB731

CB733
CB736
ST951
Chassis
Ground lead

Fig. 7
22
RX-A3030/RX-V3075
UPDATING FIRMWARE /
When the following parts are replaced, the firmware must
RX-A3030/RX-V3075
be updated to the latest version.
DIGITAL P.C.B. DIGITAL P.C.B.
FPGA Flash ROM: IC75 on DIGITAL (1) P.C.B. FPGA ROM DIGITAL1P.C.B. IC75
DSP1 (TI) Flash ROM: IC910 on DIGITAL (1) P.C.B. DSP1TI ROMDIGITAL1P.C.B. IC910
DSP2 (TI) Flash ROM: IC921 on DIGITAL (1) P.C.B. DSP2TI ROMDIGITAL1P.C.B. IC921
NETWORK Flash ROM: IC953 on DIGITAL (1) P.C.B. NETWORK ROM DIGITAL1P.C.B. IC953
Confirmation of firmware version and checksum

Before and after updating the firmware, check the
firmware version and checksum by using the self-
diagnostic function menu.
Start up the self-diagnostic function and select S4. S4. ROM VERSION/CHECKSUM
ROM VERSION/CHECKSUM menu.
Using the sub-menu, have the firmware version and
checksum displayed, and note them down.
(For details, refer to SELF-DIAGNOSTIC FUNCTION)
* When the firmware version is different from
written one after updating, perform the updating
procedure again from the beginning.
Initializing the back-up IC IC

(EEPROM: IC78 on DIGITAL (1) P.C.B.) EEPROMDIGITAL1P.C.B. IC78
After updating the firmware, the back-up IC MUST
be initialized by the following procedure to store the
setting information (soundfield parameters, system
memory and tuner presetting, etc.) properly. IC

Start up the self-diagnostic function and select S3. S3. FACTORY PRESET
FACTORY PRESET menu.
(For details, refer to SELF-DIAGNOSTIC FUNCTION)
Select PRESET RSRV, press the MAIN ZONE PRESET RSRV MAIN ZONE
key to turn off the power once and turn on the power
again. Then the back-up IC is initialized. IC
Required Tools
USB storage device USB
Firmware
RX-A3030/RX-V3075: R0339-xxxx.bin RX-A3030 R0339-xxxx.bin
Preparation
1. Download the latest firmware from the specified 1.
download source to the folder of the PC. PC
2. PC USB
2. Copy the latest firmware from the PC to the root

folder of the USB storage device.

Note) When the latest firmware is copied to a sub-

folder of the USB storage device, the update
will not proceed.
23
RX-A3030/RX-V3075
Operation Procedures
RX-A3030/RX-V3075
1. Insert the USB storage device to the USB jack. 1. USB USB
(Fig. 1) Fig. 1
2. While pressing the PURE DIRECT key, connect 2. PURE DIRECT
the power cable to the AC outlet. (Fig. 1) AC Fig. 1
"MAIN ZONE " key "PURE DIRECT" key

"MAIN ZONE " "PURE DIRECT"
USB jack
USB
USB storage device

USB
Fig. 1
3. The USB UPDATE mode is activated and USB 3. USB UPDATE USB UPDATE
UPDATE is displayed. Writing of the firmware
starts automatically. (Fig. 2) Fig. 2
Writing is started. /
Writing being executed. /
USB UPDATE VERIFYING... Sx-x:xx%
S1: NET (IC951/IC953 on DIGITAL (1) P.C.B.) section

S2: MAIN (IC78 on DIGITAL (1) P.C.B.) section
S3: DSP1 (IC910/IC911 on DIGITAL (1) P.C.B.) section
S4: DSP2 (IC920/IC921 on DIGITAL (1) P.C.B.) section
S5: FPGA (IC50/IC75 on DIGITAL (1) P.C.B.) section
Fig. 2
* If ERROR! xxxx is displayed during writing of ERROR!

the firmware, refer to List of Error Messages xxxx
to determine the cause and perform the
updating procedure again from the beginning.
4. When writing of the firmware is completed, 4. UPDATE

UPDATE SUCCESS, PLEASE... and POWER SUCCESS PLEASE... POWER OFF!
OFF! are displayed repeatedly. (Fig. 3) Fig. 3
Writing is completed. /
UPDATE SUCCESS PLEASE... POWER OFF!
Fig. 3
24
RX-A3030/RX-V3075
5. Press the MAIN ZONE key to turn off the 5. MAIN ZONE
RX-A3030/RX-V3075
power. (Fig. 1) Fig. 1
6. Remove the USB storage device from the USB 6. USB USB
jack. (Fig. 1) Fig. 1
7. Start up the self-diagnostic function and check 7.
that the firmware version and checksum are
the same as written ones. (For details, refer to

Confirmation of firmware version and checksum)

List of Error Messages /

Display /
ERROR! xxxx
Error number /
Error Number Error Message Cause

0001 Microprocessor clearing error / Microprocessor failure
0002 Microprocessor writing error /
0004 Microprocessor checksum error Microprocessor failure / Mismatch of checksum

0008 DSP1 status port error / DSP1
0010 DSP1 checksum error / DSP1 DSP1 failure /
0020 DSP1 data reception time out Malfunction of communication with microprocessor
DSP1
0040 DSP1 checksum calculation time out DSP1
DSP1
0080 DSP2 status port error / DSP2
0100 DSP2 checksum error / DSP2 DSP2 failure /
0200 DSP2 date reception time out Malfunction of communication with microprocessor
DSP2
0400 DSP2 checksum calculation time out DSP2
DSP2
0800 FPGA Flash ROM clearing error
FPGA Flash ROM FPGA Flash ROM failure /
1000 FPGA Flash ROM writing error Malfunction of communication with microprocessor
FPGA Flash ROM
2000 FPGA Flash ROM checksum error FPGA Flash ROM
FPGA Flash ROM
4000 Destination judging error No destination is written on EEPROM.
EEPROM
* The error number is displayed in the 4-digit hexadecimal notation.

4 16
* The error numbers are added when a multiple number of errors occur at the same time.

Example / If errors by the error number 0002 and 0008 occur at the same time, the error number will be displayed as 000A.
00020008000A
25
RX-A3030/RX-V3075
SELF-DIAGNOSTIC FUNCTION /
This unit has self-diagnostic functions that are intended
RX-A3030/RX-V3075
for inspection, measurement and location of faulty point.

There are 26 main menu items, each of which has sub- 26
menu items.
Listed in the table below are main menu items and sub-
menu items.

Note: Some of the menu items listed below may not apply
to the models covered in this service manual.
No. Main menu No. Sub-menu

A: Audio system
A1 DSP AUDIO 1 DSP MARGIN
2 DSP NON MARGIN
3 PLL OFF
4 INVALID ITEM (Not for service / )
A2 DIRECT AUDIO 1 ANALOG DIRECT VH
2 ANALOG DIRECT VL
A3 HDMI AUDIO 1 HDMI AUTO
2 DSD DIRECT
3 ARC1
4 HDMI ZONE
5 HDMI THROUGH (Not for service / )
A4 SPEAKERS SET 1 BI-AMP
2 ZONE/TONE MAX
3 ZONE/TONE MIN
4 ZONE MONO ON
5 ZONE MONO OFF
6 D-PARTY MODE
7 FULL MUTE
8 EXTERNAL FRONT/INTERNAL REAR PRESENCE
9 EXTERNAL FRONT/INTERNAL ZONE2
10 EXTERNAL FRONT/INTERNAL ZONE3
11 EXTERNAL FRONT PRESENCE/REAR PRESENCE
A5 MULTI CHANNEL INPUT 1 MULTI CHANNEL INPUT 8 ohms
2 MULTI CHANNEL INPUT 6 ohms
A6 MIC CHECK 1 MIC ROUTE CHECK
A7 MANUAL TEST 1 TEST ALL
2 TEST FRONT L
3 TEST CENTER
4 TEST FRONT R
5 TEST SURROUND R
6 TEST SURROUND BACK R
7 TEST SURROUND BACK L
8 TEST SURROUND L
9 TEST FRONT PRESENCE L
10 TEST FRONT PRESENCE R
11 TEST REAR PRESENCE L
12 TEST REAR PRESENCE R
13 TEST LFE 1
14 TEST LFE 2
26
RX-A3030/RX-V3075
RX-A3030/RX-V3075
D: Display system
D1 FL CHECK 1 FL CHECK
2 ALL SEGMENT OFF
3 ALL SEGMENT ON
4 CHECK PATTERN 1
5 CHECK PATTERN 2
Z: Zone system
Z1 ZONE TEST 1 AV1
2 AV2
3 AV3
4 AV4
5 AUDIO1
6 AUDIO2
7 AUDIO3
8 AUDIO4
9 V-AUX
10 PHONO
U: Universal system
U1 USB 1 USB FRONT 1 TRACK
2 USB FRONT 2 TRACK
3 USB_VBUS HIGH POWER
N: Network system
N1 NETWORK 1 IP ADDRESS CHECK
2 MAC ADDRESS CHECK
3 LINE NOISE 100 MDI (Not for service / )
4 LINE NOISE 100 MDIX (Not for service / )
5 LINE NOISE 10 MDI (Not for service / )
6 LINE NOISE 10 MDIX (Not for service / )
7 EXT TEST
8 MAC ADDRESS
C: Communication system
C1 DIGITAL PCB CHECK 1 ALL (Not for service / )
2 BUS FLASH ROM
3 BUS FPGA
4 I2C
5 FPGA RAM
6 BUS DIR
7 BUS DSP
8 EEPROM
9 RS-232C DATA CHECK (Not for service / )
10 BUS DAC
C2 NETWORK IC CHECK 1 ALL
2 LINK CHECK
3 PHY TEST
4 RAM BUS
5 APL ID CHECK
V: Video system
V1 ANALOG VIDEO CHECK 1 ANALOG BYPASS
2 DIGITAL BYPASS
3 ZONE BYPASS
4 MUTE CHECK
5 TEST PATTERN (Not for service / )
6 VIDEO IN
27
RX-A3030/RX-V3075

RX-A3030/RX-V3075
V2 DIGITAL VIDEO CHECK 1 LOOPBACK TEST 1

2 LOOPBACK TEST 2
3 LOOPBACK TEST 3
4 LOOPBACK TEST 4
5 LOOPBACK TEST 5
6 LOOPBACK TEST 6
7 HDMI REPEAT
8 DIGITAL CVBS
9 DIGITAL Y/C
10 DIGITAL COMPONENT
11 DIGITAL COMPONENT SC
12 GUI-VIDEO OUT
V3 TEST PATTERN 1 480i
2 480p
3 720p 60Hz
4 1080i 60Hz
5 1080p 60Hz
6 576i
7 576p
8 720p 50Hz
9 1080i 50Hz
10 1080p 50Hz
11 1080p 24Hz
12 1080p 24Hz 3D/FP
13 720p 60Hz 3D/FP
14 720p 50Hz 3D/FP
15 1080i 60Hz 3D/FP
16 1080i 60Hz 3D/SS
17 1080i 50Hz 3D/SS
18 720p 60Hz 3D/TB
19 720p 50Hz 3D/TB
20 1080p 24Hz 3D/TB
21 4k 24Hz
T: Troubleshooting Information
T1 POWER 1 OPERATING TIME
2 POWER-RELAY ON
3 POWER AMP B
4 OUTPUT LEVEL
5 POWER OFF TIME-OUT
T2 USAGE ENVIRONMENT 1 MAIN ZONE HIGHEST VOLUME
2 ZONE 2 HIGHEST VOLUME
3 ZONE 3 HIGHEST VOLUME
4 THM1/THM2 HIGHEST TEMPERATURE
5 THM3/THM4 HIGHEST TEMPERATURE
(Not for service / )
T3 EXTERNAL EVENT 1 HISTORY 1
2 HISTORY 2
3 HISTORY 3
4 HISTORY 4
5 HISTORY 5
6 HISTORY 6
7 HISTORY 7
8 HISTORY 8
T4 INTERNAL INFOMATION 1 DSP INFORMATION
2 BU ERROR (Not for service / )
3 NRC (Net Restart Counter) (Not for service / )
4 DAC
28
RX-A3030/RX-V3075
RX-A3030/RX-V3075
P: Power and protection system
P1 SYSTEM MONITOR 1 DC
2 PS
3 THM1/THM2
4 THM3/THM4 (Not for service / )
5 OUTPUT LEVEL
6 LIMITER CONTROL
7 L3 (J model)
8 KEY
9 USB-VBUS (Not for service / )
P2 PROTECTION HISTORY 1 HISTORY 1
1-1 POWER PORT
1-2 POWER ON TIME
1-3 LAST INPUT
1-4 LAST VOLUME
2 HISTORY 2
2-1 POWER PORT
2-2 POWER ON TIME
2-3 LAST INPUT
2-4 LAST VOLUME
3 HISTORY 3
3-1 POWER PORT
3-2 POWER ON TIME
3-3 LAST INPUT
3-4 LAST VOLUME
4 HISTORY 4
4-1 POWER PORT
4-2 POWER ON TIME
4-3 LAST INPUT
4-4 LAST VOLUME
S: System and version system
S1 FIRMWARE UPDATE 1 F/W UPDATE (Not for service / )
S2 SET INFORMATION 1 MODEL
2 DESTINATION
S3 FACTORY PRESET 1 PRESET INHIBIT/RESERVE
S4 ROM VERSION/CHECKSUM 1 SYSTEM VERSION
2 MICROPROCESSOR VERSION
3 MICROPROCESSOR CHECKSUM
4 FLASH ROM VERSION
5 FLASH ROM CHECKSUM
6 NETWORK MICROPROCESSOR VERSION
7 NETWORK MICROPROCESSOR CHECKSUM
8 DSP1 VERSION
9 DSP1 CHECKSUM
10 DSP2 VERSION
11 DSP2 CHECKSUM
12 GUI VERSION
13 FPGA GUI VERSION
14 FPGA SD VERSION
15 FPGA HD VERSION
16 HD RADIO VERSION (U model)
29
RX-A3030/RX-V3075
Starting Self-Diagnostic Function

RX-A3030/RX-V3075
While pressing the TONE/BALANCE and INFO keys, TONE/BALANCE INFO MAIN
press the MAIN ZONE key to turn on the power, and ZONE 2
release those 2 keys.
The self-diagnostic function mode is activated.
Keys of this unit /
While pressing these keys, turn on the power.

Starting Self-Diagnostic Function in

the protection cancel mode
If the protection function works and causes hindrance
to troubleshooting, cancel the protection function by
the procedure below, and it will be possible to enter the
self-diagnostic function mode. (The protection functions PS3
other than the excess current detect function and PS3
protection function will be disabled.) TONE/BALANCE INFO MAIN
While pressing the TONE/BALANCE and INFO keys, ZONE MAIN
press the MAIN ZONE key to turn on the power and ZONE 3
keep pressing those 2 keys and MAIN ZONE key for 3
seconds or longer.
FL SLEEP
The self-diagnostic function mode is activated with the
protection functions disabled.
In this mode, the SLEEP segment of the FL display flashes
to indicate that the mode is self-diagnostic function mode
with the protection functions disabled.
CAUTION!
Using this unit with the protection function disabled may
cause further damage to this unit. Use special care for
this point when using this mode.

30
RX-A3030/RX-V3075
Canceling Self-Diagnostic Function
RX-A3030/RX-V3075
1. Before canceling self-diagnostic function, execute 1. S3. FACTORY PRESET
setting for S3. FACTORY PRESET menu. (Memory
initialization inhibited or Memory initialized).
* In order to keep the user memory preserved, be
sure to select PRESET INHIBIT (Memory initialization PRESET INHIBIT
inhibited).
2. Press the MAIN ZONE key to turn off the power. 2. MAIN ZONE
Display provided when Self-Diagnostic

Function started
The display is as described below depending on the
situation when the power to this unit is turned off.
1. When the power is turned off by usual operation: 1.

NO PROTECT is displayed. Then A1-1. DSP NO PROTECT A1-1. DSP
MARGIN is displayed in a few seconds. MARGIN
Opening message / Main menu display /

After a few seconds /
A1-1
NO PROTECT DSP MARGIN
31
RX-A3030/RX-V3075
2. When the protection function worked to turn 2.

RX-A3030/RX-V3075
off the power:

The information of protection function which worked at
that time is displayed. Then A1-1. DSP MARGIN is A1-1. DSP MARGIN
displayed in a few seconds.
Note: At that time if you restart the self-diagnostic NO PROTECT
function after turning off the power once, NO 1.
PROTECT will be displayed. That is because
that situation is equal to 1. When the power is
turned off by usual operation:.
However history of the protection function is P2. PROTECTION HISTORY
stored in memory as backup data. For details,
refer to P2. PROTECTION HISTORY menu.
2-1. When there is a history of protection function 2-1.

due to excess current.
I PROTECT
Cause: An excessive current flowed through the power

amplifier.
Supplementary information: As over current of the
power amplifier is detected, check condition of each
power transistor.

Turning on the power without correcting the abnormality

will cause the protection function to work immediately and
the power supply will instantly be shut off.
Notes:
Applying the power to this unit without correcting
the abnormality can be dangerous and cause
additional circuit damage. To avoid this, if I I PROTECT
PROTECT protection function works 1 time, MAIN ZONE
the power will not turn on even when the MAIN
ZONE key is pressed. In order to turn on the
power again, start up the self-diagnostic function.
The output transistors in each amplifier channel
should be checked for damage before applying
power to this unit. DC
Amplifier current should be monitored by
measuring DC voltage across the emitter resistors
for each channel.
32
RX-A3030/RX-V3075
2-2. When the protection function worked due to 2-2. DC
RX-A3030/RX-V3075
abnormal DC output.
DC PRT:xxxH H: Displayed when the voltage is HIGHER than upper limit

L: Displayed when the voltage is LOWER than lower limit

xxx: A/D conversion value of voltage at the moment when the protection function worked
(Reference voltage: 3.3 V=255)
A/D
3.3 V=255
Cause: DC output of the power amplifier is abnormal. DC

Supplementary information: The protection function
worked due to a DC voltage appearing at the speaker
terminal. A cause could be a defect in the amplifier.
5
will cause the protection function to work in 5 seconds

and the power supply will be shut off.
2-3. When the protection function worked due to 2-3.

abnormal voltage in the power supply section.
PSxPRT:xxxL H: Displayed when the voltage is HIGHER than upper limit


A/D
3.3 V=255
PS1/PS2/PS3
Cause: The voltage in the power supply section is

abnormal.
worked due to a defect or overload in the power supply.
1

Notes:
Applying the power to this unit without correcting
the abnormality can be dangerous and cause
additional circuit damage. To avoid this, if PS DC
PS
and DC protection function works 3 times 3 MAIN
consecutively, the power will not turn on even ZONE
when the MAIN ZONE key is pressed. In order
to turn on the power again, start up the self-
diagnostic function.
The output transistors in each amplifier channel
should be checked for damage before applying
power to this unit. DC
Amplifier current should be monitored by
measuring DC voltage across the emitter resistors
for each channel.
33
RX-A3030/RX-V3075
2-4. When the protection function worked due to 2-4.

RX-A3030/RX-V3075
excessive heatsink temperature.
TMPxPRT:xxxL H: Displayed when the voltage is HIGHER than upper limit


A/D
3.3 V=255
TMP1/TMP2
Cause: The temperature of the heatsink is excessive.

worked due to the temperature limit being exceeded.
Causes could be poor ventilation or a defect related to
the thermal sensor. 1

History of protection function

When the protection function has worked, its history
is stored in memory as backup data.
Even if no abnormality is noted while servicing the
unit, an abnormality which has occurred previously
can be defined as long as the backup data has been
stored. P2. PROTECTION HISTORY
For details, refer to P2. PROTECTION HISTORY
menu.
34
RX-A3030/RX-V3075
Operation procedure of Main menu
RX-A3030/RX-V3075
and Sub-menu
There are 26 main menu items, each of which has sub- 26
menu items.
Main menu selection

Select the main menu using SCENE 2 (forward) and SCENE 2SCENE 1
SCENE 1 (reverse) keys.
Sub-menu selection
Select the sub-menu using SCENE 4 (forward) and SCENE SCENE 4SCENE 3
3 (reverse) keys.
Keys of this unit /
Main menu selection Sub-menu selection

Reverse Forward Reverse Forward

Functions in Self-Diagnostic Function

mode
In addition to the self-diagnostic function menu items,
functions listed below are available.

Power ON/OFF
Master volume
Muting
Input selection ZONE
Zone control
* Functions related to the tuner and the set menu are
not available.
Initial settings when Self-Diagnostic

Function started
The following initial settings are used when self-diagnostic
function is started. -20 dB
Master volume: -20 dB ZONE 2 -3.5 dB
ZONE 2 volume: -3.5 dB ZONE 3 -3.5 dB
ZONE 3 volume: -3.5 dB AV1
Input: AV1 A1-1. DSP MARGIN
Main menu: A1-1. DSP MARGIN LARGEBass out to SWFR
Speaker setting: LARGE, Bass out to SWFR
(All channels) HDMI OFF
HDMI control: Off ZONE 2 ZONE 3 ZONE 4 ON
ZONE 2/ZONE 3/ZONE 4: On
* When self-diagnostic function is canceled, these
settings are restored to those before starting self-
diagnostic function. 35
RX-A3030/RX-V3075
Details of Self-Diagnostic Function

RX-A3030/RX-V3075
menu
A1. DSP AUDIO A1. DSP AUDIO
This menu is used to check audio signal route via DSP. DSP
A1-1. DSP MARGIN A1-1. DSP MARGIN

The audio signal is output including the head DSP
margin via DSP.
* When input source is stereo, signal is 2ch
assigned as below.
Front L: Front L, Center, Surround L, Front L Front LCenterSurround L
Surround Back L Surround Back L
Front R: Front R, Surround R, Surround Front R Front RSurround RSurround
Back R Back R
Front L +10 dB: Subwoofer Front L +10 dBSubwoofer
A1-1
DSP MARGIN
A1-2. DSP NON MARGIN A1-2. DSP NON MARGIN

The SUBWOOFER signal is output including DSP
the head margin via DSP.
The audio signal other than SUBWOOFER is DSP
output without including the head margin via
DSP.
A1-2
DSP NON MARGIN
A1-3. PLL OFF A1-3. PLL OFF

The audio signal is output with the PLL (Phase DSP PLLPhase Lock
Lock Loop, IC914) turned off via DSP. LoopIC914
A1-3
PLL=OFF
A1-4. INVALID ITEM A1-4. INVALID ITEM

Not for service.
A1-4
INVALID ITEM
36
RX-A3030/RX-V3075
RX-A3030/RX-V3075
Not for service.
A1-5
INVALID ITEM

Not for service.
A1-6
INVALID ITEM

Not for service.
A1-7
INVALID ITEM
A2. DIRECT AUDIO A2. DIRECT AUDIO

This menu is used to check audio signal route of DIRECT
PURE DIRECT mode.
A2-1. DIRECT VH A2-1. DIRECT VH

The analog input audio signal is output to PURE DIRECT
FRONT L/R in PURE DIRECT mode. FRONT L/R
VH: Voltage High, VHVoltage High
RY180 on AMPPOWER (1) P.C.B.: Off AMPPOWER1P.C.B. RY180O
A2-1
DIRECT :VH
A2-2. DIRECT VL A2-2. DIRECT VL

The analog input audio signal is output to PURE DIRECT
FRONT L/R in PURE DIRECT mode. FRONT L/R
VL: Voltage Low, VHVoltage Low
RY180 on AMPPOWER (1) P.C.B.: On AMPPOWER1P.C.B. RY180On
A2-2
DIRECT :VL
37
RX-A3030/RX-V3075
A3. HDMI AUDIO A3. HDMI AUDIO

RX-A3030/RX-V3075
This menu is used to check the route of audio signal HDMI IN/OUT
input to HDMI IN/OUT jack.
* Before check using A3-3. ARC 1 menu, be sure A3-3. ARC
to connect a TV monitor equipped with Audio Audio Return Channel
Return Channel function to this unit in advance.
A3-1 A3-1. HDMI AUTO

HDMI AUTO The audio signal input to selected HDMI IN jack is output.
HDMI IN
A3-2 A3-2. INVALID ITEM

DSD DIRECT DSD (Direct Stream Digital) is output by the direct mode.
DSDDirect Stream Digital
A3-3 A3-3. ARC1 (Audio Return Channel function)

ARC 1 The audio signal input to HDMI OUT 1 jack is output.
HDMI OUT 1
A3-4 A3-4. HDMI ZONE

HDMI Zone The audio signal input to HDMI OUT 2 jack is output.
HDMI OUT 2
A3-5 A3-5. HDMI THROUGH

HDMI Through Not for service.

A4. SPEAKERS SET A4. SPEAKERS SET

This menu is used to check the speaker output.
A4-1 A4-1. BI-AMP

BI-AMP The FRONT L/R signal is distributed to BI-AMP L/R terminals.
FRONT L/R BI-AMP L/R
A4-2 A4-2. ZONE/TONE=MAX

ZONE/TONE=MAX The audio signal is output to FRONT L/R, CENTER, SURROUND L/R, ZONE 2 L/R and ZONE 3 L/R
terminals with the tone control BASS +6 dB, TREBLE +6 dB.
BASS +6 dB
TREBLE +6 dB FRONT L/RCENTER
SURROUND L/RZONE 2 L/RZONE 3 L/R
A4-3 A4-3. ZONE/TONE=MIN

ZONE/TONE=MIN The audio signal is output to FRONT L/R, CENTER, SURROUND L/R, ZONE 2 L/R and ZONE 3 L/R
terminals with the tone control BASS -6 dB, TREBLE -6 dB.
BASS -6 dB TREBLE -6 dB FRONT L/RCENTER
SURROUND L/RZONE 2 L/RZONE 3 L/R
38
RX-A3030/RX-V3075
A4-4 A4-4. ZONE MONO ON
RX-A3030/RX-V3075
ZONE MONO=On The analog audio signal is output to ZONE 2 L/R and ZONE 3 L/R terminals in monaural.
ZONE 2 L/RZONE 3 L/R
A4-5 A4-5. ZONE MONO OFF

ZONE MONO=Off The analog audio signal is output to ZONE 2 L/R and ZONE 3 L/R terminals in stereo.
ZONE 2 L/RZONE 3 L/R
A4-6 A4-6. D-PARTY MODE

D-PARTY MODE The FRONT L/R signal is distributed to ZONE 2 L/R and ZONE 3 L/R terminals.
ZONE 2/ZONE 3 volume: -3.5 dB
FRONT L/R ZONE 2 L/RZONE 3 L/R
ZONE 2 ZONE 3 volume-3.5 dB
A4-7 A4-7. FULL MUTE

FULL MUTE The SPEAKERS output are muted at all channels.
SPEAKERS
A4-8 A4-8. EXTERNAL FRONT/INTERNAL REAR PRESENCE

EXT.F+INT.RPR The audio signal is output to CENTER, SURROUND L/R, SURROUND BACK L/R, FRONT PRESENCE L/
R and REAR PRESENCE L/R.
CENTERSURROUND L/RSURROUND BACK L/RFRONT PRESENCE L/RREAR
PRESENCE L/R
A4-9 A4-9. EXTERNAL FRONT/INTERNAL ZONE 2

EXT.F+INT.Z2 The audio signal is output to CENTER, SURROUND L/R, SURROUND BACK L/R, ZONE 2 L/R (EXTRA
SP1 L/R) and ZONE 2 L/R (EXTRA SP2 L/R).
CENTERSURROUND L/RSURROUND BACK L/RZONE 2 L/REXTRA SP1 L/R
ZONE 2 L/REXTRA SP2 L/R
A4-10 A4-10. EXTERNAL FRONT/INTERNAL ZONE 3

EXT.F+INT.Z3 The audio signal is output to CENTER, SURROUND L/R, SURROUND BACK L/R, ZONE 3 L/R (EXTRA
SP1 L/R) and ZONE 3 L/R (EXTRA SP2 L/R) terminals.
CENTERSURROUND L/RSURROUND BACK L/RZONE 3 L/REXTRA SP1 L/R
ZONE 3 L/REXTRA SP2 L/R
A4-11 A4-11. EXTERNAL FRONT PRESENCE/REAR PRESENCE

EXT.FPR+RPR The audio signal is output to FRONT PRESENCE L/R and REAR PRESENCE L/R.
FRONT PRESENCE L/RREAR PRESENCE L/R

INVALID ITEM Not for service.


INVALID ITEM Not for service.

39
RX-A3030/RX-V3075
A5. MULTI CHANNEL INPUT A5. MULTI CHANNEL INPUT

RX-A3030/RX-V3075
This menu is used to check the route of audio signal MULTI CHANNEL INPUT
input to MULTI CHANNEL INPUT.
A5-1. MULTI CHANNEL INPUT 8 ohms A5-1. MULTI CHANNEL INPUT 8 ohms
The audio signal input to MULTI CHANNEL MULTI CHANNEL INPUT
INPUT is output with the speaker impedance 8 8
ohms setting.
A5-1
8ohm MULTI CH
A5-2. MULTI CHANNEL INPUT 6 ohms A5-2. MULTI CHANNEL INPUT 6 ohms
The audio signal input to MULTI CHANNEL MULTI CHANNEL INPUT
INPUT is output with the speaker impedance 6 6
ohms setting.
A5-2
6ohm MULTI CH
A6. MIC CHECK A6. MIC CHECK
A6-1. MIC ROUTE CHECK A6-1. MIC ROUTE CHECK

The audio signal input to the YPAO MIC jack is YPAO A/D
output to FRONT L and FRONT R channels via D/A FRONT LFRONT R
A/D-D/A.
A6-1
MIC ROUTE
40
RX-A3030/RX-V3075
A7. MANUAL TEST A7. MANUAL TEST
RX-A3030/RX-V3075
The test noise generated by built-in noise generator DSP
in DSP is output to the channels specified by the sub-
menu.
Test noise /
30 Hz to 80 Hz
for SUBWOOFER / SUBWOOFER
pink noise /
500 Hz to 2 kHz
for other than SUBWOOFER / SUBWOOFER
pink noise /
A7-1 A7-1. TEST ALL

TEST ALL The test noise is output to FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK L/R,
FRONT PRESENCE L/R and LFE 1/2 (SUBWOOFER 1/2) channels.
FRONT L/RCENTERSURROUND L/RSURROUND BACK L/R
FRONT PRESENCE L/RLFE 1/2SUBWOOFER 1/2
A7-2 A7-2. TEST FRONT L

TEST FRNT L The test tone is output to FRONT L channel.
FRONT L
A7-3 A7-3. TEST CENTER

TEST CENTER The test tone is output to CENTER channel.
CENTER
A7-4 A7-4. TEST FRONT R

TEST FRNT R The test tone is output to FRONT R channel.
FRONT R
A7-5 A7-5. TEST SURROUND R

TEST SURR R The test tone is output to SURROUND R channel.
SURROUND R
A7-6 A7-6. TEST SURROUND BACK R

TEST SB R The test tone is output to SURROUND BACK R channel.
SURROUND BACK R
A7-7 A7-7. TEST SURROUND BACK L

TEST SB L The test tone is output to SURROUND BACK L channel.
SURROUND BACK L
A7-8 A7-8. TEST SURROUND L

TEST SURR L The test tone is output to SURROUND L channel.
SURROUND L
A7-9 A7-9. TEST FRONT PRESENCE L

TEST FP L The test tone is output to FRONT PRESENCE L channel.
FRONT PRESENCE L
41
RX-A3030/RX-V3075
A7-10 A7-10. TEST FRONT PRESENCE R

RX-A3030/RX-V3075
TEST FP R The test tone is output to FRONT PRESENCE R channel.

FRONT PRESENCE R
A7-11 A7-11. TEST REAR PRESENCE L

TEST RP L The test tone is output to REAR PRESENCE L channel.
REAR PRESENCE L
A7-12 A7-12. TEST REAR PRESENCE R

TEST RP R The test tone is output to REAR PRESENCE R channel.
REAR PRESENCE R
A7-13 A7-13. TEST LFE 1 (SUBWOOFER)

TEST LFE 1 The test tone is output to LFE 1 channel.
LFE 1
A7-14 A7-14. TEST LFE 2 (SUBWOOFER)

TEST LFE 2 The test tone is output to LFE 2 channel.
LFE 2
42
RX-A3030/RX-V3075
D1. FL CHECK D1. FL CHECK
RX-A3030/RX-V3075
This menu is used to check operation of the FL display. FL
FL display / FL
D1-1. INITIAL DISPLAY /
D1-2. ALL SEGMENT OFF /
D1-3. ALL SEGMENT ON /
* After check, change to next sub-menu at once.

D1-4. CHECK PATTERN 1 / 1
Example/
Lighting on segments in lattice.

D1-5. CHECK PATTERN 2 / 2 Short Normal

Segment conditions of the FL tube is checked by FL

turning ON and OFF all segments.
Next, a short between segments next to each other
is checked by turning ON and OFF all segments
alternately (in lattice).
(In the above example, the segments in the second 2
row from the top are shorted.)
43
RX-A3030/RX-V3075
Z1. ZONE TEST Z1. ZONE TEST

RX-A3030/RX-V3075
This menu is used to check audio signal route to ZONE 2ZONE 3ZONE 4
ZONE 2, ZONE 3 and ZONE 4.
Z1-1 Z1-1. AV 1
AV1 The analog audio signal input to AV 1 is output to ZONE 2 OUT and ZONE 3 OUT jacks.
AV 1 ZONE 2 OUTZONE 3 OUT
Z1-2 Z1-2. AV 2
Z1-3 Z1-3. AV 3
Z1-4 Z1-4. AV 4
AV4 he 2-channel PCM signal input to AV 4 is output to HDMI OUT 2 (ZONE 4 OUT) jack.
AV 4 2 PCM HDMI OUT 2ZONE 4 OUT
Z1-5 Z1-5. AUDIO 1

AUDIO1 The analog audio signal input to AUDIO 1 is output to ZONE 2 OUT and ZONE 3 OUT jacks.
AUDIO 1 ZONE 2 OUTZONE 3 OUT
Z1-6 Z1-6. AUDIO 2

Z1-7 Z1-7. AUDIO 3

Z1-8 Z1-8. AUDIO 4

Z1-9 Z1-9. V-AUX

V-AUX The analog audio signal input to VIDEO AUX is output to ZONE 2 OUT and ZONE 3 OUT jacks.
VIDEO AUX ZONE 2 OUTZONE 3 OUT
Z1-10 Z1-10. PHONO

PHONO The analog audio signal input to PHONO is output to ZONE 2 OUT and ZONE 3 OUT jacks.
PHONO ZONE 2 OUTZONE 3 OUT
44
RX-A3030/RX-V3075
U1. USB U1. USB
RX-A3030/RX-V3075
This menu is used to check the audio signal route from USB
USB storage device.
U1-1. USB FRONT 1 TRACK U1-1. USB FRONT 1 TRACK

The 1st music file stored in the USB storage USB USB
device connected to the USB jack is 1
reproduced.
* Copy 2 or more music files from PC to the PC USB
root folder of the USB storage device in 2
advance.
U1-1
USB_F 1 TRACK
U1-2. USB FRONT 2 TRACK U1-2. USB FRONT 2 TRACK

The 2nd music file stored in the USB storage USB USB
device connected to the USB jack is 2
reproduced.
U1-2
USB_F 2 TRACK
U1-3. USB_VBUS HIGH POWER U1-3. USB_VBUS HIGH POWER

The output current (USB_VBUS) of USB jack is USB USB_VBUS 2.1A
output at up to 2.1A/5V. 5V
U1-3
USB_VBUS_HPWR
45
RX-A3030/RX-V3075
N1. NETWORK N1. NETWORK

RX-A3030/RX-V3075
This menu is used to check functions related to

NETWORK. LAN
Connect between LAN port of broadband router and NETWORK
NETWORK jack of this unit with a network cable.
* When the network condition varies while sub-menu
is displayed (e.g., the network is deactivated
once), the correct result will not be displayed.
In that case, once turn off the power to this unit,
then start up the self-diagnostic function again
and select this menu.
N1-1. IP ADDRESS CHECK N1-1. IP ADDRESS CHECK

This menu is used to check that IP address IP
can be obtained.
N1-1
IP AD CHK:OK
OK: Connected (IP address obtained)
IP
NG: No traffic / Disconnected

N1-2. MAC ADDRESS CHECK N1-2. MAC ADDRESS CHECK

This menu is used to check that MAC address MAC
is written.
N1-2
MAC AD CHK:OK
OK: Normal /
NG: Unwritten /
N1-3. LINE NOISE 100 MDI N1-3. LINE NOISE 100 MDI
Not for service.
N1-3
LN MDI 100
N1-4. LINE NOISE 100 MDIX N1-4. LINE NOISE 100 MDIX
Not for service.
N1-4
LN MDIX 100
46
RX-A3030/RX-V3075
N1-5. LINE NOISE 10 MDI N1-5. LINE NOISE 10 MDI
RX-A3030/RX-V3075
Not for service.
N1-5
LN MDI 10
N1-6. LINE NOISE 10 MDIX N1-6. LINE NOISE 10 MDIX

Not for service.
N1-6
LN MDIX 10
N1-7. EXT TEST N1-7. EXT TEST

Transmission/reception of the NETWORK jack NETWORK
is checked. NETWORK
With the power turned off, short the pins of the
NETWORK jack as shown in the figure below.
Start up the self-diagnostic function and select
this menu.
Transmission/reception test is executed and
its result is displayed.
Note: Be sure to return the shorted pins

to their original condition after
executing this test.
8 7 6 5 4 3 2 1 N1-7
EXT TEST:OK
OK: Normal /
NG: Abnormal /
--: Checking /
NETWORK jack
N1-8. MAC ADDRESS N1-8. MAC ADDRESS

Written MAC address is displayed. MAC

N1-8
00A0DExxxxxx
47
RX-A3030/RX-V3075
C1. DIGITAL P.C.B. CHECK C1. DIGITAL P.C.B. CHECK

RX-A3030/RX-V3075
This menu is used to check the communication and DIGITAL P.C.B.

bus line connection between devices on DIGITAL
P.C.B.
C1-1. ALL C1-1. ALL

Not for service.
C1-1
ALL:NG Ext.JIG
When test result using the C1-9. RS-232C LOOP BACK
CHECK menu is NG, Ext. JIG is displayed.
C1-9. RS-232C LOOP BACK CHECK
NG Ext. JIG
OK: No error detected /

NG: An error is detected /
--: Checking /
C1-2. BUS FLASH ROM C1-2. BUS FLASH ROM

FLASH ROM (IC75)s reading/writing are FLASH ROMIC75
checked.
C1-2
BUS FROM:OK
--: Checking /
C1-3. BUS FPGA C1-3. BUS FPGA

Communication and bus line connection IC79 FPGAIC40IC50
between microprocessor (IC79) and FPGA
(IC40, IC50) are checked.
C1-3
BUS_FPGA:OK,OK
IC50
IC40

--: Checking /
48
RX-A3030/RX-V3075
C1-4. I2C C1-4. I2C
RX-A3030/RX-V3075
The I2C (Inter integrated circuit) bus line I2CInter integrated circuit
connection is checked.
C1-4
000000 0 000 0 : No error detected /
1 : An error is detected /
Error detection of VIDEO P.C.B. / VIDEO P.C.B.

Error detection of Video encoder (IC20) / IC20
Error detection of Video decoder (IC21) / IC21
Error detection of Front HDMI equalizer (IC32) / HDMI IC32
Error detection of HDMI transmitter 2 (IC62) / HDMI 2IC62
Error detection of HDMI transmitter 1 (IC61) / HDMI 1IC61
Error detection of HDMI receiver 2 (IC4) / HDMI 2IC4
Error detection of HDMI receiver 1 (IC3) / HDMI 1IC3
Error detection of HDMI switcher 2 (IC2) / HDMI 2IC2
Error detection of HDMI switcher 1 (IC1) / HDMI 1IC1
C1-5. FPGA RAM C1-5. FPGA RAM

SDRAM (IC53)s reading/writing are checked. SDRAMIC53

C1-5
FPGA_RAM:OK
C1-6. BUS DIR C1-6. BUS DIR

Communication and bus line connection IC79 DIRIC900IC903
between microprocessor (IC79) and DIR
C1-6
DIR BUS:OK,OK
DIR2: IC903
DIR1: IC900

49
RX-A3030/RX-V3075
C1-7. BUS DSP C1-7. BUS DSP

RX-A3030/RX-V3075
Communication and bus line connection IC79 DSPIC911IC920

between microprocessor (IC79) and DSP
C1-7
DSP BUS:OK,OK
DSP2: IC920
DSP1: IC911

C1-8. EEPROM C1-8. EEPROM

EEPROM (IC78)'s reading is checked. EEPROMIC78
C1-8
EEPROM:OK
C1-9. RS-232C DATA CHECK C1-9. RS-232C DATA CHECK

Not for service.
C1-9
232C DATA:NG
C1-10. BUS DAC C1-10. BUS DAC

Communication and bus line connection IC79 DACIC942IC943
between microprocessor (IC79) and DAC
C1-10
DAC BUS:OK,OK
IC943
IC942

50
RX-A3030/RX-V3075
C2. NETWORK IC CHECK C2. NETWORK IC CHECK
RX-A3030/RX-V3075
This menu is used to check the communication and bus
line connection between devices related to network.
C2-1. ALL C2-1. ALL

The synthetic judgment result of sub-menu C2-2 C2-5
C2-2 to C2-5 is displayed.
C2-1
ALL:OK Ext.JIG
When test result using the C2-2. LINK CHECK menu is
NG, the sub-menu C2-2 is NG, Ext. JIG is displayed.
C2-2. LINK CHECK NG
Ext. JIG

--: Checking /
C2-2. LINK CHECK C2-2. LINK CHECK

LAN cable connection is checked. LAN
Connect between NETWORK jack of this unit NETWORK
and LAN port of broadband router with a LAN
network cable.
* When the network condition varies while
sub-menu is displayed (e.g., the network
is deactivated once), the correct result will
not be displayed. In that case, once turn
off the power to this unit, then start up the
self-diagnostic function again and select
this menu.
C2-2
LINK CHK:OK
OK: Normal /
NG: Disconnected /
--: Checking /
C2-3. PHY (Ethernet PHYceiver) TEST C2-3. PHYEthernet PHYceiverTEST

Communication and bus line connection PHYIC955 NETWORK IC951
between PHY (IC955) and NETWORK
microprocessor (IC951) are checked.
C2-3
PHY TEST:OK
--: Checking /
51
RX-A3030/RX-V3075
C2-4. RAM BUS C2-4. RAM BUS

RX-A3030/RX-V3075
Communication and bus line connection SDRAMIC952 NETWORK IC951

between SDRAM (IC952) and NETWORK
microprocessor (IC951) are checked.
C2-4
RAM BUS:OK
--: Checking /
C2-5. APL (Apple) ID CHECK C2-5. APLAppleID CHECK

Apple authentication IC (IC956) device ID is Apple ICIC956 ID
checked.
C2-5
APL ID:OK
--: Checking /
52
RX-A3030/RX-V3075
V1. ANALOG VIDEO CHECK V1. ANALOG VIDEO CHECK
RX-A3030/RX-V3075
This menu is used to check the analog video signal
route.
V1-1. ANALOG BYPASS V1-1. ANALOG BYPASS

The video signal is converted and output as
shown below.
V1-1
ANALOG BYPASS
ANALOG BYPASS
HDMI IN HDMI OUT
DIGITAL DIGITAL
DIGITAL
IC3 IC61
IC50
HDMI HDMI
FPGA
Receiver Transmitter
Component In DIGITAL DIGITAL Component Out

IC21 IC20
MUTE
VIDEO VDEC_N_RST VIDEO
PCB PCB
Decoder Encoder
VIDEO VIDEO
IC305 IC305
NJW1327 NJW1327
S Video In S Video Out
Composite In Composite Out
V1-2. DIGITAL BYPASS V1-2. DIGITAL BYPASS

shown below.
V1-2
DIGITAL BYPASS
DIGITAL BYPASS
HDMI IN HDMI OUT
DIGITAL DIGITAL
DIGITAL
IC3 IC61
IC50
HDMI HDMI
FPGA

IC21 IC20
MUTE
VIDEO VDEC_N_RST VIDEO
PCB PCB
Decoder Encoder
VIDEO VIDEO
IC305 IC305
NJW1327 NJW1327
53
RX-A3030/RX-V3075
V1-3. ZONE BYPASS V1-3. ZONE BYPASS

RX-A3030/RX-V3075

shown below.
V1-3
ZONE BYPASS
ZONE BYPASS
HDMI IN HDMI OUT
DIGITAL DIGITAL
DIGITAL
IC3 IC61
IC50
HDMI HDMI
FPGA

IC21 IC20
VIDEO VIDEO
PCB PCB
Decoder Encoder
VIDEO VIDEO
IC305 IC305
NJW1327 NJW1327
* MON/ZONE OUTPUT is selectable different from AV-OUT.
V1-4. MUTE CHECK V1-4. MUTE CHECK

The video signal is muted.
V1-4
MUTE CHECK
MUTE CHECK
HDMI IN HDMI OUT
DIGITAL DIGITAL
DIGITAL
IC3 IC61
IC50
HDMI HDMI
FPGA
MUTE
IC21 IC20
VIDEO VIDEO
PCB PCB
Decoder Encoder
VIDEO VIDEO
IC305 IC305
NJW1327 NJW1327
V1-5. TEST PATTERN V1-5. TEST PATTERN

Not for service.
V1-5
TEST PATTERN
V1-6. VIDEO INFORMATION V1-6. VIDEO INFORMATION

The information of input analog video signals
is displayed.
V1-6
VID IN:480i60
54
RX-A3030/RX-V3075
V2. DIGITAL VIDEO CHECK V2. DIGITAL VIDEO CHECK
RX-A3030/RX-V3075
This menu is used to check the digital video signal
route.
V2-1. LOOPBACK TEST 1 V2-1. LOOPBACK TEST 1

Execute the test for all HDMI IN jacks by HDMI IN
repeating the procedure below.
1. Select sub-menu other than V2-1. 1. V2-1
2. Connect between any of the HDMI IN jacks 2. HDMI IN 1 HDMI OUT 1
and HDMI OUT 1 jack with an HDMI cable. HDMI
3. Select V2-1. The test result is displayed in a 3. V2-1
few seconds.
V2-1
TEST1:OK
--: Checking /
HDMI Cable for Loopback
CB7 CB6 CB5 CB4 CB3 CB2 CB1 CB30 CB62 CB61
Front-HDMI-Board
HDMI HDMI HDMI HDMI HDMI HDMI HDMI HDMI IN HDMI HDMI
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC2 IC1 SDRAM HDMI HDMI
HDMI SWITCHER 2 HDMI SWITCHER 1 TRANSMITTER 2 TRANSMITTER 1
ADV7630 ADV7630 Sii9136CTU-3 Sii9136CTU-3
IC4 IC50
HDMI RECEIVER 2 FPGA
ADV7619 EP4CE15F23C6N
IC3
HDMI RECEIVER 1
ADV7619
IC40
FPGA
EP4CE15F23C6N
IC21 IC20
VIDEO DECODER VIDEO ENCODER
ADV7181C ADV7172
55
RX-A3030/RX-V3075

RX-A3030/RX-V3075
HDMI receiver 1 IC (IC3) is checked. HDMI 1 ICIC3

2. Connect between any of the HDMI IN jacks 2. HDMI IN 1 HDMI OUT
and HDMI OUT jack with an HDMI cable. HDMI
3. Select the input source corresponding 3. HDMI IN
to the connected HDMI IN jack by using INPUT
INPUT knob. 4. V2-2
4. Select V2-2. The test result is displayed in a
few seconds.
Select the input source Result
AV1 V-AUX V2-2

TEST2:OK


--: Checking /
Front-HDMI-Board
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC4 IC50
IC3
HDMI RECEIVER 1
ADV7619
IC40
FPGA
EP4CE15F23C6N
IC21 IC20
ADV7181C ADV7172
56
RX-A3030/RX-V3075
RX-A3030/RX-V3075
HDMI transmitter 1 IC (IC61) is checked. HDMI 1 ICIC61

1. Select sub-menu other than V2-3.
2. Connect between any of the HDMI IN jacks 1. V2-3
and HDMI OUT 1 jack with an HDMI cable. 2. HDMI IN 1 HDMI OUT 1
3. Select the input source corresponding HDMI
to the connected HDMI IN jack by using 3. HDMI IN
INPUT knob. INPUT
few seconds.
AV1 V-AUX V2-3

TEST3:OK


--: Checking /
Front-HDMI-Board
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC4 IC50
IC3
HDMI RECEIVER 1
ADV7619
IC40
FPGA
EP4CE15F23C6N
IC21 IC20
ADV7181C ADV7172
57
RX-A3030/RX-V3075

RX-A3030/RX-V3075
HDMI transmitter 2 IC (IC62) is checked. HDMI ICIC62

1. Select sub-menu other than V2-4.
2. Connect between any of the HDMI IN jacks 1. V2-4
and HDMI OUT 2 jack with an HDMI cable. 2. HDMI IN 1 HDMI OUT 2
3. Select the input source corresponding HDMI
to the connected HDMI IN jack by using 3. HDMI IN
INPUT knob. INPUT
few seconds.
AV1 V-AUX V2-4

TEST4:OK


--: Checking /
Front-HDMI-Board
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC4 IC50
IC3
HDMI RECEIVER 1
ADV7619
IC40
FPGA
EP4CE15F23C6N
IC21 IC20
ADV7181C ADV7172
58
RX-A3030/RX-V3075
RX-A3030/RX-V3075
FPGA IC (IC40) is checked. FPGA ICIC40
2. Connect between any of the HDMI IN jacks 2. HDMI IN 1 HDMI OUT 2
and HDMI OUT 2 jack with an HDMI cable. HDMI
INPUT knob. 4. V2-5
few seconds.
AV1 V-AUX V2-5

TEST5:OK


--: Checking /
Front-HDMI-Board
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC4 IC50
IC3
HDMI RECEIVER 1
ADV7619
IC40
FPGA
EP4CE15F23C6N
IC21 IC20
ADV7181C ADV7172
59
RX-A3030/RX-V3075

RX-A3030/RX-V3075
HOMI receiver 2 IC (IC4) is checked by using ZONE 2 HDMI 2

the ZONE 2 route. ICIC4
2. Connect between any of the HDMI IN jacks 2. HDMI IN 1 HDMI OUT
and HDMI OUT jack with an HDMI cable. HDMI
3. Press the ZONE CONTROL key and 3. ZONE CONTROL ZONE 2
ZONE 2 is enabled.
INPUT knob. 5. V2-6
few seconds.
Zone2:Input Zone2:Input V2-6

AV1 V-AUX TEST6:OK
Flashes when ZONE 2 is enabled. OK: No error detected /
ZONE 2

--: Checking /
Front-HDMI-Board
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC4 IC50
IC3
HDMI RECEIVER 1
ADV7619
IC40
FPGA
EP4CE15F23C6N
IC21 IC20
ADV7181C ADV7172
60
RX-A3030/RX-V3075
V2-7. HDMI REPEAT V2-7. HDMI REPEAT
RX-A3030/RX-V3075
The video/audio signals input to HDMI IN jack HDMI IN
are output to HDMI OUT jack. HDMI OUT
V2-7
HDMI REPEAT **
The Deep Color video signals is input, 30 bit or
36 bit is displayed.
Deep Color 30 bit
36 bit
TV
HDMI
HDMI output
HDMI
BD/DVD player
Front-HDMI-Board
(ZONE 4 OUT)
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC50
FPGA
IC4 (ZONE 4 INPUT) EP4CE15F23C6N
HDMI RECEIVER 2
ADV7619
IC3
HDMI RECEIVER 1
ADV7619
IC40
FPGA
EP4CE15F23C6N
IC21 IC20
ADV7181C ADV7172
61
RX-A3030/RX-V3075
V2-8. DIGITAL CVBS V2-8. DIGITAL CVBS

RX-A3030/RX-V3075
The video (CVBS) signal is converted and

output as shown below.
V2-8 TV
DIGITAL CVBS HDMI
Front-HDMI-Board
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC4 IC50
IC3
HDMI RECEIVER 1
Video output ADV7619
VIDEO
IC40
FPGA
EP4CE15F23C6N
BD/DVD player
IC21 IC20 Y,CbCr
VIDEO DECODER VIDEO ENCODER Y,C
CVBS ADV7181C ADV7172 CVBS
V2-9. DIGITAL Y/C V2-9. DIGITAL Y/C

The s-video (Y, C) signal is converted and
output as shown below.
V2-9 TV
DIGITAL Y/C HDMI
Front-HDMI-Board
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC4 IC50
IC3
S-video output HDMI RECEIVER 1
S-VIDEO ADV7619
IC40
FPGA
EP4CE15F23C6N
BD/DVD player
IC21 IC20 Y,CbCr
Y,C VIDEO DECODER VIDEO ENCODER Y,C
ADV7181C ADV7172 CVBS
62
RX-A3030/RX-V3075
V2-10. DIGITAL COMPONENT V2-10. DIGITAL COMPONENT
RX-A3030/RX-V3075
The component video (Y, Cb, Cr) signal is
converted and output as shown below.
V2-10
DIGITAL Cmp
TV
HDMI
Front-HDMI-Board
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC4 IC50
Component video output HDMI RECEIVER 2 FPGA
COMPONENT ADV7619
IC3 EP4CE15F23C6N
HDMI RECEIVER 1
ADV7619
IC40
FPGA
BD/DVD player EP4CE15F23C6N
Y,CbCr IC21 IC20 Y,CbCr

63
RX-A3030/RX-V3075
V2-11. DIGITAL COMPONENT SC V2-11. DIGITAL COMPONENT SC

RX-A3030/RX-V3075
The component video (Y, Cb, Cr) signal is

converted and output as shown below.
HDMI video output up-scaling:
480i/p, 576i/p only => 1080p 480i/p576i/p => 1080p
V2-11
DIGITAL Cmp SC
TV
HDMI
Front-HDMI-Board
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC4 IC50
Component output HDMI RECEIVER 2 FPGA
COMPONENT ADV7619
IC3 EP4CE15F23C6N
HDMI RECEIVER 1
ADV7619
IC40
FPGA
BD/DVD player EP4CE15F23C6N
Y,CbCr IC21 IC20 Y,CbCr

64
RX-A3030/RX-V3075
V2-12. GUI-VIDEO OUT V2-12. GUI-VIDEO OUT
RX-A3030/RX-V3075
The GUI is output from FPGA (IC50 on DIGITAL FPGADIGITAL1P.C.B. IC50 GUI
(1) P.C.B.).
V2-12
GUI-VIDEO OUT
TV
HDMI
Front-HDMI-Board
IN7 IN6 IN5 IN4 IN3 IN2 IN1 Front OUT2 OUT1 1080p
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC50
FPGA
IC4 EP4CE15F23C6N
HDMI RECEIVER 2
ADV7619
IC3 GUI
HDMI RECEIVER 1
ADV7619
IC40
FPGA
EP4CE15F23C6N
IC21 IC20 Y,CbCr

65
RX-A3030/RX-V3075
V3. TEST PATTERN V3. TEST PATTERN

RX-A3030/RX-V3075
The GUI is output to HDMI OUT jack with its resolution GUI HDMI
converted as shown below. OUT
TV
HDMI
Front-HDMI-Board
IC32
HDMI EQUALIZER
Sii9587CNUC-3 IC53
128Mbit IC62 IC61
IC50
FPGA
IC4 EP4CE15F23C6N
HDMI RECEIVER 2
ADV7619
IC3 GUI
HDMI RECEIVER 1
ADV7619
IC40
FPGA
EP4CE15F23C6N
IC21 IC20 Y,CbCr

V3-1. 480i V3-2. 480p V3-3. 720p 60Hz V3-4. 1080i 60Hz
V3-1 V3-2 V3-3 V3-4
480i 480p 720p 60 1080i 60
V3-5. 1080p 60Hz V3-6. 576i V3-7. 576p V3-8. 720p 50Hz
V3-5 V3-6 V3-7 V3-8
1080p 60 576i 576p 720p 50
V3-9. 1080i 50Hz V3-10. 1080p 50Hz V3-11. 1080p 24Hz V3-12. 1080p 24Hz 3D/FP
V3-9 V3-10 V3-11 V3-12
1080i 50 1080p 50 1080p 24 1080p 24 3D/FP
(FP: Frame Packing)
V3-13. 720p 60Hz 3D/FP V3-14. 720p 50Hz 3D/FP V3-15. 1080i 60Hz 3D/FP V3-16. 1080i 60Hz 3D/SS
V3-13 V3-14 V3-15 V3-16
720p 60 3D/FP 720p 50 3D/FP 1080i 60 3D/FP 1080i 60 3D/SS
(SS: Side-by-Side)
V3-17. 1080i 50Hz 3D/SS V3-18. 720p 60Hz 3D/TB V3-19. 720p 50Hz 3D/TB V3-20. 1080p 24Hz 3D/TB
V3-17 V3-18 V3-19 V3-20
1080i 50 3D/SS 720p 60 3D/TB 720p 50 3D/TB 1080p 24 3D/TB
(TB: Top-and-Bottom)
V3-21. 4k 24Hz
V3-21
4k 24
(4k: Digital cinema 4K, Resolution 3996 2160p)
66
RX-A3030/RX-V3075
T1. POWER T1. POWER
RX-A3030/RX-V3075
This menu is used to display the operating time and
operation frequency of this unit.

* The operating time and operation frequency during
the self-diagnostic function mode will not be stored.
T1-1. OPERATING TIME T1-1. OPERATING TIME

The operating time of this unit is displayed.
The operating time will be erased by pressing STRAIGHT
the STRAIGHT key.
T1-1
0000D 00H 00M
Minute (0M to 59M) / 0M 59M
Hour (0H to 23H) / 0H 23H
Day (0D to 9999D) / 0D 9999D
T1-2. POWER-RELAY ON T1-2. POWER-RELAY ON

The operation frequency of the power relay RY201 16
(RY201) is displayed in hexadecimal notation.
The operation frequency will be erased by STRAIGHT
pressing the STRAIGHT key.
T1-2
PR-ON Num:0000
Operation frequency / 0 to FFFF (up to 65,535 times)
0 FFFF 65,535
T1-3. POWER AMP B T1-3. POWER AMP B

The operation frequency of the POWER AMP POWER AMP B RY180
B relay (RY180) is displayed in hexadecimal 16
notation. STRAIGHT
The operation frequency will be erased by
T1-3
P-AMP B Num:00
Operation frequency / 0 to FF (up to 255 times)
0 FF 255
67
RX-A3030/RX-V3075
T1-4. OUTPUT LEVEL T1-4. OUTPUT LEVEL

RX-A3030/RX-V3075
The maximum value of the speaker output level 16

is displayed in hexadecimal notation.
The maximum value will be erased by pressing STRAIGHT
the STRAIGHT key.
T1-4
OUTLVL MAX: 00
Maximum value / 0 to FF
0 FF
T1-5. POWER OFF TIME-OUT T1-5. POWER OFF TIME-OUT

The number of time-out times of each module
when the power is turned off will be displayed 16
in hexadecimal notation. STRAIGHT
All the number of time-out times will be erased
by pressing the STRAIGHT key.
T1-5
TO: 0/ 0/ 0/ 0 0 to FF (up to 255 times) / 0 FF 255
VIDEO
NET
HDMI
Power relay
68
RX-A3030/RX-V3075
T2. USAGE ENVIRONMENT T2. USAGE ENVIRONMENT
RX-A3030/RX-V3075
This menu is used to display the maximum level of ZONE ZONE 2 ZONE 3
the MAIN ZONE / ZONE 2 / ZONE 3 volume and the
maximum value of the detected heatsink temperature
when this unit is operated.
ZONE ZONE 2 ZONE 3
* The maximum level of the MAIN ZONE / ZONE 2
/ ZONE 3 volume and the maximum value of the
detected heatsink temperature during the self-
diagnostic function mode will not be stored.
T2-1. MAIN ZONE HIGHEST VOLUME T2-1. MAIN ZONE HIGHEST VOLUME
The maximum value of the MAIN ZONE volume 1 ZONE
level maintained for longer than 1 minute is
displayed. STRAIGHT ZONE
The maximum value of the MAIN ZONE volume
level will be erased by pressing the STRAIGHT
key.
T2-1
MAIN VOL:-----
Maximum value / -80.0 to +16.5 dB
-80.0 +16.5 dB
T2-2. ZONE 2 HIGHEST VOLUME T2-2. ZONE 2 HIGHEST VOLUME

The maximum value of the ZONE 2 volume 1 ZONE 2
displayed. STRAIGHT ZONE 2
The maximum value of the ZONE 2 volume
key.
T2-2
Z2 VOL: -----
-80.0 +16.5 dB
T2-3. ZONE 3 HIGHEST VOLUME T2-3. ZONE 3 HIGHEST VOLUME

The maximum value of the ZONE 3 volume 1 ZONE 3
displayed. STRAIGHT ZONE 3
The maximum value of the ZONE 3 volume
key.
T2-3
Z3 VOL: -----
-80.0 +16.5 dB
69
RX-A3030/RX-V3075
T2-4. THM1/THM2 HIGHEST TEMPERATURE T2-4. THM1/THM2 HIGHEST TEMPERATURE

RX-A3030/RX-V3075
The minimum value of the detected heatsink 16

temperature is displayed in hexadecimal
notation. STRAIGHT
The minimum value of the detected heat sink
temperature will be erased by pressing the

STRAIGHT key.
THM1 51 FF
Normal value THM2 51 FF
THM1: 51 to FF
THM2: 51 to FF
T2-4
TMa MIN:--/-- Heatsink temperature / 0 (High) to FF (Low)
0 FF
THM2
THM1
T2-5. THM3/THM4 HIGHEST TEMPERATURE T2-5. THM3/THM4 HIGHEST TEMPERATURE

Not for service.
T2-5
TMb MIN:--/--
T3. EXTERNAL EVENT T3. EXTERNAL EVENT

This menu is used to display the history of key
operation.
1
* No matter how many times the same key is pressed,
it will be stored only once as its history.
* The key operation during the self-diagnostic function
mode will not be stored. STRAIGHT

All history of key operation will be erased by pressing
the STRAIGHT key.
* Numeric values in the figure are given as reference
only.
T3-1. HISTORY 1 T3-2. HISTORY 2 T3-3. HISTORY 3 T3-4. HISTORY 4

T3-1 T3-2 T3-3 T3-4
0205-80-FF-FF 0101 0205-80-FF-FF 0101
T3-5. HISTORY 5 T3-6. HISTORY 6 T3-7. HISTORY 7 T3-8. HISTORY 8

T3-5 T3-6 T3-7 T3-8
0102 0104 0103 0205-80-FF-FF
70
RX-A3030/RX-V3075
List of key operation /
RX-A3030/RX-V3075
Display /
Key number AD value 1 AD value 2 AD value 3 Key name /
AD 1 AD 2 AD 3
0205 77 89 FF FF MAIN ZONE
0208 40 53 FF FF ZONE 2
020B 84 100 FF FF ZONE 3
020E xx xx FF FF ZONE 4
020F 77 89 00 09 FF MAIN ZONE + STRAIGHT (Advanced setup mode)
0300 2D 3F FF FF SCENE 1
0301 1C 2C FF FF SCENE 2
0302 0A 1B FF FF SCENE 3
0303 00 09 FF FF SCENE 4
0500 FF 9C AD FF PROGRAM
0501 FF 8A 9B FF PROGRAM
0530 FF 00 09 FF STRAIGHT
0533 FF FF 9C AD PURE DIRECT
0800 FF 0A 1B FF TONE/BALANCE
0900 FF 2D 3F FF CURSOR
0901 FF C0 D1 FF CURSOR
0902 FF 54 64 FF CURSOR
0903 FF 77 89 FF CURSOR
0904 FF 65 76 FF ENTER
0905 FF D2 E3 FF RETURN
0906 FF 40 53 FF ON SCREEN
0907 FF 1C 2C FF OPTION
0908 FF AE BF FF DISPLAY
0A00 FF FF 2D 3F INFO
0C00 FF FF 40 53 ZONE CONTROL
2C00 FF FF 8A 9B TUNING/CH
2C01 FF FF 77 89 TUNING/CH
2C02 FF FF 65 76 AM
2C03 FF FF 54 64 FM
2C04 FF FF 00 09 PRESET
2C05 FF FF 0A 1B PRESET
2C06 FF FF 1C 2C MEMORY
0101 VOLUME knob ()
0102 VOLUME knob (+)
0103 INPUT knob ()
0104 INPUT knob (+)
7A xxxx * For the details of the remote control key display, refer to
REMOTE CONTROL.
7E xxxx REMOTE CONTROL

71
RX-A3030/RX-V3075
T4. INTERNAL INFORMATION T4. INTERNAL INFORMATION

RX-A3030/RX-V3075
T4-1. DSP INFORMATION T4-1. DSP INFORMATION

This menu is used to display the DSP information
stored in memory as backup data before DSP
rebooting.
STRAIGHT DSP
The DSP information will be erased by pressing
the STRAIGHT key.
T4-1
DSP:--/--/-- --: Not stored /
Decode format /
Channels /
Sampling frequency /
Sampling frequency Channels Decode format

Display Sampling frequency [kHz] Display Channels Display Decode format

kHz
0 32 0 Dual Mono 0 Analog
1 44.1 1 1/0 1 PCM
2 48 2 2/0 2 Dolby Digital
3 64 3 3/0 3 Dolby Digital EX
4 88.2 4 2/1 4 DTS
5 96 5 3/1 5 DTS 9624
6 128 6 2/2 6 DTS ES Matrix
7 176.4 7 3/2 7 DTS ES Discrete
8 192 8 2/3 8 DTS 96 ES Matrix
10 8 9 3/3 9 AAC
11 11 10 2/4 10 DSD
12 12 11 3/4 11 Multi PCM
13 16 12 HD Multi channel 12 Dolby Digital Plus
14 22.05 13 Unknown 13 Dolby Digital Plus EX
15 24 14 Dolby True HD
16 Unknown 15 Dolby True HD EX
16 DTS Express
17 DTS HD
18 DTS HD Master Audio
19 Digital
20 MP3
21 WMA
22 FLAC
25 Unknown
72
RX-A3030/RX-V3075
T4-2. BU ERROR T4-2. BU ERROR
RX-A3030/RX-V3075
Not for service.
T4-2
BU ERR:-255
T4-3. NRC (Net Restart Counter) T4-3. NRCNet Restart Counter

Not for service.
T4-3
NRC: 0
T4-4. DAC T4-4. DAC

The number of times that DAC (IC942, IC943) DACIC942IC943
locked out is displayed.
The operation frequency will be erased by STRAIGHT
T4-4
DAC: 0/ 0
DAC2: IC943
DAC1: IC942
73
RX-A3030/RX-V3075
P1. SYSTEM MONITOR P1. SYSTEM MONITOR

RX-A3030/RX-V3075
This menu is used to display the A/D conversion

value of the microprocessor which detects panel keys A/D
and protection functions by using the sub-menu.
When P1-8. KEY sub-menu is selected, keys become P1-8. KEY
inoperable due to detection of the values of all keys.
However, it is possible to advance to the next menu by SCENE 4 SCENE 3
pressing the SCENE 4 (forward) key or SCENE 3
(reverse) key on the remote control.
only.
P1-1. DC P1-1. DC
Power amplifier DC (DC voltage) output is DC
detected. IC77 5
DC_PRT

The voltage at 5 pin (DC_PRT) of IC77 is 32 74
displayed. 3.3 V=255
Normal value: 32 to 74 DC
* If DC becomes out of the normal value range,
the protection function works to turn off the
power.
P1-1
DC: 41
P1-2. PS P1-2. PS
Power supply voltage (PS) protection detection. PS
The voltage at 2 pin (PS1_PRT)/1 pin (PS2_ IC77 2 PS1_PRT 1 PS2_
PRT)/13 pin (PS3_PRT) of IC77 are displayed. PRT 13 PS3_PRT

Voltage detects
PS1: ACBL, AC12, AC7, +3.3HDR (U model),
-3.3V PS1 ACBLAC12AC7-3.3V
PS2: 12V, 12RY, +5A, 44V PS2 12V 12RY+5A44V
PS3: +5.5V PS3 +5.5V
Normal value
PS1: 83 to 136 (U model) PS1 47 111
(Pure Direct: 127 to 180) Pure Direct100 165
47 to 111 PS2 43 148
(C, R, T, K, A, B, G, F, L, S models) PS3 132 168
(Pure Direct: 100 to 165) 3.3 V=255
PS2: 43 to 148
PS1PS2 PS3
PS3: 132 to 168

* If PS1, PS2 or PS3 becomes out of the
normal value range, the protection function
works to turn off the power.
P1-2
PS:112/ 99/153
PS3
PS2
PS1
74
RX-A3030/RX-V3075
P1-3. THM1/THM2 P1-3. THM1/THM2
RX-A3030/RX-V3075
Temperature of the heatsink (THM) is detected. THM
The voltage at 12 pin (THM1) of IC77 and 1 IC77 12 THM1
IC76 1 THM2
pin (THM2) of IC76 are displayed.
Normal value
THM1/THM2: 43 to 255 (U, R, T, K, A, B, G, THM1/THM2 43 255
F, L, S models) 3.3 V=255
117 to 255 (C model) THM1/THM2
* If THM1/THM2 becomes out of the normal
value range, the protection function works
to turn off the power.
P1-3
TMa: 99 / 100
THM2
THM1
P1-4. THM3/THM4 (C model) P1-4. THM3/THM4C model

Temperature of the heatsink (THM) is detected.
The voltage at 2 pin (THM3) and 4 pin (THM4)
of IC76 are displayed.
Normal value
THM3/THM4: 43 to 255
* If THM3/THM4 becomes out of the normal
value range, the protection function works
to turn off the power.
P1-4
TMb:130 / 130
THM4
THM3
P1-5. OUTPUT LEVEL P1-5. OUTPUT LEVEL

Speaker output level is detected.
The voltage at 4 pin (AMP_OLV) of IC77 is IC77 4 AMP_OLV
displayed.
(Reference voltage: 3.3 V=255) 3.3 V=255
P1-5
OUTLVL: 0
P1-6. LIMITER CONTROL P1-6. LIMITER CONTROL

Power limiter control is detected.
The voltage at 4 pin (AMP_LMT) of IC79 is IC79 4 AMP_LMT
displayed.
(Reference voltage: 3.3 V=255) 3.3 V=255
P1-6
LMTCNT: 255
75
RX-A3030/RX-V3075
P1-7. L3 (J model) P1-7. L3 (J model)

RX-A3030/RX-V3075
Not for service. D L3VIDEO1P.C.B. CB301 11

IC77 14 L3_DET

3.3 V=255
P1-7
L3: 2
P1-8. KEY P1-8. KEY

Panel key is detected.
When the A/D conversion value of the panel A/D
key becomes out of the specified range,
normal operation will not be available.
In that case, check the constant of voltage
dividing resistor, solder condition, etc. Refer to P1-8. KEY
table.
* When P1-8. KEY menu is selected, keys SCENE 4
become inoperable due to detection of the SCENE 3
values of all keys. However, it is possible
to advance to the next menu by pressing
the SCENE 4 (forward) key or SCENE 3 3.3 V=255
(reverse) key on the remote control.
P1-8
KY:255/255/255
KEY3
KEY2
KEY1
Display / KEY1 Display / KEY2 Display / KEY3

09 SCENE 4 09 STRAIGHT 09 PRESET
10 27 SCENE 3 10 27 TONE/BALANCE 10 27 PRESET
28 44 SCENE 2 28 44 OPTION 28 44 MEMORY
45 63 SCENE 1 45 63 45 63 INFO
64 83 ZONE 2 ON/OFF 64 83 ON SCREEN 64 83 ZONE CONTROL
84 100 ZONE 3 ON/OFF 84 100 84 100 FM
119 137 MAIN ZONE 101 118 ENTER 101 118 AM
255 Key off 119 137 119 137 TUNING/CH
138 155 PROGRAM 138 155 TUNING/CH
156 173 PROGRAM 156 173 PURE DIRECT
174 191 DISPLAY 255 Key off
192 209
210 227 RETURN
255 Key off
P1-9. USB-VBUS P1-9. USB-VBUS

Not for service.
P1-9
USB-VBUS: 5
76
RX-A3030/RX-V3075
P2. PROTECTION HISTORY P2. PROTECTION HISTORY
RX-A3030/RX-V3075
This menu is used to display the history of protection
function.
1 4
In the protection function history 1 to 4, the setting
information for operation of each protection function /
will be stored. After selecting the sub-menu, press
the (cursor down) key / (cursor up) key, and
STRAIGHT
the setting information will be displayed.

All history of protection function and setting information
will be erased by pressing the STRAIGHT key.

only.
The display will be changed by pressing the (cursor down)

P2-1 2-1. History 1 / 1
key / (cursor up) key.
4th:I Prt
/

Setting information for operation of the protection function
P2-2 P2-2. History 2 / 2
3rd:PS1 000 POWER PORT
P2-x
P-PORT:0011000 The status of the port for the power control is
displayed.
P2-3 P2-3. History 3 / 3
2nd:Dc 000 0: Off /

1: On /
FL: FLD_PON (DIGITAL (1) P.C.B. IC70, 9pin)
USB: USB_VBUS_PON
P2-4 P2-4. History 4 / 4
(DIGITAL (1) P.C.B. IC79, 84pin)
1st:Tmp 000
NET: NCPU_PON (DIGITAL (1) P.C.B. IC79, 82 pin)
xxx: A/D conversion value of
VIDEO: VID_PON (DIGITAL (1) P.C.B. IC71, 15pin)
voltage at the moment
when the protection DSP: DSP_PON (DIGITAL (1) P.C.B. IC79, 47pin)
function worked. HDMI: HDMI_PON (DIGITAL (1) P.C.B. IC70, 2pin)
(Reference voltage: 3.3 V Power Relay: +3.3s_PON
=255) (DIGITAL (1) P.C.B. IC79, 165pin)
P2-x POWER-RELAY ON TIME

A/D PR-ON TM:1000M The operation time of the power relay (RY201 of
3.3 V=255 POWER2 P.C.B.) is displayed by the unit time of
minute.
0 to 1,092 minute (maximum)
POWER2 P.C.B. RY201

0 1,092
P2-x LAST INPUT
LAST IN:AUDIO3 The input source which was selected last is

displayed.

P2-x LAST VOLUME LEVEL
LAST VOL:-16.5 The volume level which was selected last is

displayed.
-80.0 to +16.5 dB

-80.0 +16.5 dB
77
RX-A3030/RX-V3075
S1. FIRMWARE UPDATE S1. FIRMWARE UPDATE

RX-A3030/RX-V3075
Not for service.
S1-1
F/W UPDATE?
S2. SET INFORMATION S2. SET INFORMATION

This menu is used to display the model name and
destination of this unit.
S2-1. MODEL S2-1. MODEL

The model name of this unit is displayed.
S2-1
MDL:A3030 255
Not for service. /

Model name /
A3030 : RX-A3030
V3075 : RX-V3075
S2-2. DESTINATION S2-2. DESTINATION

The destination of this unit is displayed.
S2-2
DEST:U 28
A/D conversion value / A/D

Destination /
Destination J U C R (R, S) T K A BG (B, G, F) L

A/D conversion value
0 12 13 39 40 67 68 92 93 115 116 140 141 169 199 221 222 244
(3.3 V=255)
78
RX-A3030/RX-V3075
S3. FACTORY PRESET S3. FACTORY PRESET
RX-A3030/RX-V3075
This menu is used to reserve/inhibit initialization of the ICEEPROMDIGITAL1P.C.B.
back-up IC (EEPROM: IC78 on DIGITAL (1) P.C.B.). IC78
S3-1 S3-1. PRESET INHIBIT (Initialization inhibited) / PRESET INHIBIT

PRESET INHI Initialization of the back-up IC is not executed. Select this sub-menu to protect the values set by the user.
IC

S3-1 S3-2. PRESET RESERVED (Initialization reserved) / PRESET RESERVED

PRESET RSRV Initialization of the back-up IC is reserved. (Actual initialization is executed when the power is turned on
next.) To reset to the original factory settings or to reset the backup IC, select this sub-menu and press
the (Power) key to turn off the power.

CAUTION: Before setting to the PRESET RESERVED, PRESET RESERVED

write down the existing preset memory content
of the tuner. (This is because setting to the
PRESET RESERVED will cause the user
memory content to be erased.)
S4. ROM VERSION/CHECKSUM S4. ROM VERSION/CHECKSUM

The firmware version and checksum values are
displayed.
The checksum is obtained by adding the data at every 8
8-bit and expressing the result as a hexadecimal 16
notation.
only.
S4-1 S4-1. SYSTEM VERSION

SYS-VER. 0.21 The firmware version is displayed.

S4-2 S4-2. MICROPROCESSOR VERSION

VER.00021 The firmware version of MICROPROCESSOR (IC79 on DIGITAL (1) P.C.B.) is displayed.
DIGITAL1P.C.B. IC79
S4-3 S4-3. MICROPROCESSOR CHECKSUM

SUM.D080 The checksum value of MICROPROCESSOR (IC79 on DIGITAL (1) P.C.B.) is displayed.
DIGITAL1P.C.B. IC79
S4-4 S4-4. FLASH ROM VERSION

FR-V.00033 The firmware version of FLASH ROM (IC75 on DIGITAL (1) P.C.B.) is displayed.
FLASH ROMDIGITAL1P.C.B. IC75
79
RX-A3030/RX-V3075
S4-5 S4-5. FLASH ROM CHECKSUM

RX-A3030/RX-V3075
FR-S.573E The checksum value of FLASH ROM (IC75 on DIGITAL (1) P.C.B.) is displayed.
FLASH ROMDIGITAL1P.C.B. IC75
S4-6 S4-6. NETWORK MICROPROCESSOR VERSION

S-VER.0034 The firmware version of Network microprocessor (IC951 on DIGITAL (1) P.C.B.) is displayed.
DIGITAL1P.C.B. IC951
S4-7 S4-7. NETWORK MICROPROCESSOR CHECKSUM

S-SUM.51F722F5 The checksum value of Network microprocessor (IC951 on DIGITAL (1) P.C.B.) is displayed.
DIGITAL1P.C.B. IC951
S4-8 S4-8. DSP1 VERSION

D1-V. 1.03r2 The firmware version of DSP1 (IC911 on DIGITAL (1) P.C.B.) is displayed.
DSP1DIGITAL1P.C.B. IC911
S4-9 S4-9. DSP1 CHECKSUM

D1-S.922547D4 The checksum value of DSP1 (IC911 on DIGITAL (1) P.C.B.) is displayed.
S4-10 S4-10. DSP2 VERSION

D2-V. 1.06r2 The firmware version of DSP2 (IC920 on DIGITAL (1) P.C.B.) is displayed.
S4-11 S4-11. DSP2 CHECKSUM

D2-S.E5B042DE The checksum value of DSP2 (IC920 on DIGITAL (1) P.C.B.) is displayed.
S4-12 S4-12. GUI VERSION

G-V.000000237 The firmware version of GUI data is displayed.
GUI
S4-13 S4-13. FPGA GUI VERSION

FPGA-G-V. 25 The firmware version of GUI section in FPGA (IC50 on DIGITAL (1) P.C.B.) is displayed.
FPGADIGITAL1P.C.B. IC50 GUI
S4-14 S4-14. FPGA SD (Standard Definition) VERSION

FPGA-S-V. 24 The firmware version of SD I/P scaler section in FPGA (IC50 on DIGITAL (1) P.C.B.) is displayed.
FPGADIGITAL1P.C.B. IC50 SD I/P

S4-15 S4-15. FPGA HD (High Definition) VERSION

FPGA-H-V. 6 The firmware version of HD I/P scaler section in FPGA (IC50 on DIGITAL (1) P.C.B.) is displayed.
FPGADIGITAL1P.C.B. IC50 HD I/P

S4-16 S4-16. HD RADIO VERSION (U model)

HDR. A001 The firmware version of HD radio is displayed.
80
RX-A3030/RX-V3075
POWER AMPLIFIER ADJUSTMENT /

Perform all adjustments with no signal applied.
RX-A3030/RX-V3075
Warming up before adjustment is not required.
Idling Current Adjustment

1. Turn all the semi-fixed variable resisters for idling 1.
current adjustment counterclockwise fully.
2. Turn on the power to this unit. 2.
3. Adjust all channels so that the voltage value 3.
at test point is the same as center value of the
specified range.
DC Offset Confirmation DC
After idling current adjustment, confirm that DC offset DC
of all channels are within the specified range.
AMP (1) P.C.B.

Idling current adjustments DC offset confirmations
Item DC
Test Point Adjustment Point Rating Test Point Rating

Center CB105 pin1, pin2 VR107 Speaker Terminal (TE150)
Surround L CB107 pin1, pin2 VR106 Speaker Terminal (TE153) DC -100 mV
Front L CB108 pin1, pin2 VR104 DC 15 2 mV Speaker Terminal (TE150) to
Surround Back L CB109 pin1, pin2 VR105 Speaker Terminal (TE152) +100 mV
Front Presence L CB106 pin1, pin2 VR108 Speaker Terminal (TE180)
AMP (1) P.C.B.
CB108
CB105 VR108 VR106 CB107 VR105 CB109
VR104
VR107 CB106
+ + + + +
DC 15 2 mV DC 15 2 mV DC 15 2 mV DC 15 2 mV DC 15 2 mV
Center Surround L Front L Idling current
Front Presence L Surround Back L
81
RX-A3030/RX-V3075
AMP (2) P.C.B.

RX-A3030/RX-V3075
Idling current adjustments DC offset confirmations

Item DC
Test Point Adjustment Point Rating Test Point Rating

Surround Back R CB104 pin1, pin2 VR100 Speaker Terminal (TE152)
Front R CB103 pin1, pin2 VR102 Speaker Terminal (TE150) DC -100 mV to
DC 15 2 mV
Surround R CB102 pin1, pin2 VR101 Speaker Terminal (TE153) +100 mV
Front Presence R CB101 pin1, pin2 VR103 Speaker Terminal (TE180)
AMP (2) P.C.B.
CB104 VR102 CB103 VR101 CB102 VR103

VR100 CB101
+ + + +
DC 15 2 mV DC 15 2 mV DC 15 2 mV DC 15 2 mV
Front R Surround R Idling current
Surround Back R Front Presence R
82
RX-A3030/RX-V3075
DISPLAY DATA
V4001 : 23-MT-04GINK (OPERATION P.C.B.)
RX-A3030/RX-V3075
82 1
PATTERN AREA
PIN CONNECTION
Pin No. 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
Connection F2 F2 NP NP NP NP LGND PGND VH VDD OSC RESET CS CP DA TSA TSB NP NP NP NP NP
Pin No. 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
Connection NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP
Pin No. 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
Connection NP NP NP NP NP NP NP NP NP NP NP NP NP NC NC NC NC NC NC NC NC NC Q23G 23G NP NP NP NP F1 F1
Note : 1) F1, F2 ..... Filament pin 2) NP ..... No pin 3) DL ..... Datum line pin 4) LGND ..... Logic GND pin 5) PGND ..... Power GND pin
6) HV ..... High voltage supply pin 7) VDD ..... Logic voltage supply pin 8) OSC ..... Pin for self-oscillation 9) RESET ..... Reset input
10) CS ..... Chip select input pin 11) CP ..... Shift resister clock 12) DA ..... Serial data input 13) TSA,B ..... Test pin
14) Solder composition is Sn-3Ag-0.5Cu. 15) Field of vision is a minimum of 25.0 from the upper side. 22.8 from the lower side.
16) 23G ..... Grid 17) Q23G ..... Driver output port 18) NC ..... No connection
GRID ASSIGNMENT
16G 18G 20G 22G
1G 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G 23G
15G 17G 19G 21G
(B) (A) (B) (A) (B) (A) (B) (A) (B)
(B) (B) (B) (B) (B) (B) (B) (B) (B) (B) (B) (B) (B) (B)
(A) (A) (A) (A) (A) (A) (A) (A) (A) (A) (A) (A) (A) (A)
23G 1a 2a 3a
a
1-1 2-1 3-1 4-1 5-1 f b
S5
S2 1-2 2-2 3-2 4-2 5-2

g
e c
1-3 2-3 3-3 4-3 5-3 d
1-4 2-4 3-4 4-4 5-4

(23G)
1-5 2-5 3-5 4-5 5-5
S1 S6
S3 1-6 2-6 3-6 4-6 5-6
(23G) 1-7 2-7 3-7 4-7 5-7
S4
(1G-22G) (23G)
83
RX-A3030/RX-V3075
Anode connection
RX-A3030/RX-V3075
16G, 20G, 15G, 17G, 21G,

1G-14G 15G 18, 19G 22G 23G 1G-14G 19, 20G 23G
17G 21G 16G 18G 21G
D0B 1-1B 1-1B 1-1B 1-1B 1-1B 1-1B 1a D0A 1-1A 1-1A 1-1A 1-1A 1-1A
D1B 2-1B 2-1B 2-1B 2-1B 2-1B 2-1B 2a D1A 2-1A 2-1A 2-1A 2-1A 2-1A
D2B 3-1B 3-1B 3-1B 3-1B 3-1B 3-1B 3a,3f,3c,3d D2A 3-1A 3-1A 3-1A 3-1A 3-1A
D3B 4-1B 4-1B 4-1B 4-1B 4-1B 4-1B 1b D3A 4-1A 4-1A 4-1A 4-1A 4-1A
D4B 5-1B 5-1B 5-1B 5-1B 5-1B 5-1B 2b D4A 5-1A 5-1A 5-1A 5-1A 5-1A
D5B 1-2B 1-2B 1-2B 1-2B 1-2B 1-2B 3g D5A 1-2A 1-2A 1-2A 1-2A 1-2A
D6B 2-2B 2-2B 2-2B 2-2B 2-2B 2-2B 1f D6A 2-2A 2-2A 2-2A 2-2A 2-2A
D7B 3-2B 3-2B 3-2B 3-2B 3-2B 3-2B 2f D7A 3-2A 3-2A 3-2A 3-2A 3-2A
D8B 4-2B 4-2B 4-2B 4-2B 4-2B 4-2B 3b,3e D8A 4-2A 4-2A 4-2A 4-2A 4-2A
D11B 2-3B 2-3B 2-3B 2-3B 2-3B 2-3B S5 D11A 2-3A 2-3A 2-3A 2-3A 2-3A
D12B 3-3B 3-3B 3-3B 3-3B 3-3B 3-3B 1c D12A 3-3A 3-3A 3-3A 3-3A 3-3A
D13B 4-3B 4-3B 4-3B 4-3B 4-3B 4-3B 2c D13A 4-3A 4-3A 4-3A 4-3A 4-3A
D14B 5-3B 5-3B 5-3B 5-3B 5-3B 5-3B 1e D14A 5-3A 5-3A 5-3A 5-3A 5-3A
D15B 1-4B 1-4B 1-4B 1-4B 1-4B 1-4B 2e D15A 1-4A 1-4A 1-4A 1-4A 1-4A S1
D16B 2-4B 2-4B 2-4B 2-4B 2-4B 2-4B 1d D16A 2-4A 2-4A 2-4A 2-4A 2-4A S1
D17B 3-4B 3-4B 3-4B 3-4B 3-4B 3-4B 2d D17A 3-4A 3-4A 3-4A 3-4A 3-4A S3
D18B 4-4B 4-4B 4-4B 4-4B 4-4B 4-4B S6 D18A 4-4A 4-4A 4-4A 4-4A 4-4A
D19B 5-4B 5-4B 5-4B 5-4B 5-4B 5-4B D19A 5-4A 5-4A 5-4A 5-4A 5-4A
D21B 2-5B 2-5B 2-5B 2-5B 2-5B 2-5B (UP) D21A 2-5A 2-5A 2-5A 2-5A 2-5A S4
D25B 1-6B 1-6B 1-6B 1-6B 1-6B 1-6B (UP) D25A 1-6A 1-6A 1-6A 1-6A 1-6A
D30B 1-7B 1-7B 1-7B 1-7B 1-7B 1-7B (DOWN) D30A 1-7A 1-7A 1-7A 1-7A 1-7A
D34B 5-7B 5-7B 5-7B 5-7B 5-7B 5-7B (DOWN) D34A 5-7A 5-7A 5-7A 5-7A 5-7A
84
RX-A3030/RX-V3075
Timing chart
RX-A3030/RX-V3075
16G, 20G, 15G, 17G, 21G,
1G-14G 15G 18, 19G 22G 23G 1G-14G 19, 20G 23G
17G 21G 16G 18G 21G
D0B T1-T14 T15 T17 T19 T21 T23 T24 D0A T1-T14 T15 T17 T19 T21 T23
D22B T1-T14 T15 T17 T19 T21 T23 T24 D22A T1-T14 T15 T17 T19 T21
85
RX-A3030/RX-V3075
IC DATA
IC911, IC920: D80YK113CPTP400 (DIGITAL (1) P.C.B.)
RX-A3030/RX-V3075
DSP (Digital signal processor)

* No replacement part available. /
JTAG Interface DSP Subsystem
System Control
C674xTM
DSP MICRO-
PLL/Clock PROCESSOR
Input Generator
Clock(s) w/OSC Memory Protection
I/O Protection AET
General-
Purpose 32 KB 32 KB
Timer L1 Pgm L1 RAM
Power/Sleep
General- Controller
Purpose 256 KB L2 RAM
Timer RTC/ Pin
(Watchdog) 32-KHz Multiplexing 1024 KB L2 ROM
OSC
Switched Control Resource (SCR)
Peripherals
DMA Audio Ports Serial Interface
GPIO
EDMA3 dMAX McASP I 2C SPI UART
w/FIFO
Control Timers Shared Memory
128 KB
eHRPWM eCAP eQEP RAM
Connectivity External Memory Interface
USB2.0 MMC/SD EMIFA(8b/16b) EMIFB

OTG Ctlr HPI (8b) NAND/Flash SDRAM Only
PHY 16b SDRAM (16b/32b)
125 AHCLKX0/AHCLKX2/USB_REFCLKIN/GP2[11]
130 ACLKR0/ECAP1/APWM1/GP2[15]
126 ACLKX0/ECAP0/APWM0/GP2[12]
123 UART1_TXD/AXR0[10]/GP3[10]
132 AMUTE1/EHRPWMTZ/GP4[14]
129 AHCLKR0/GP2[14]/BOOT[11]
122 UART1_RXD/AXR0[9]/GP3[9]
124 AXR0[11]/AXR2[0]/GP3[11]
127 AFSX0/GP2[13]/BOOT[10]
118 AXR0[6]/ACLKR2/GP3[6]
112 AXR0[1]/ACLKX2/GP3[1]
116 AXR0[4]/AXR2[1]/GP3[4]
115 AXR0[3]/AXR2[2]/GP3[3]
113 AXR0[2]/AXR2[3]/GP3[2]
111 AXR0[0]/AFSR2/GP3[0]
117 AXR0[5]/AFSX2/GP3[5]
105 EMB_A[10]/GP7[12]
EMB_A[11]/GP7[13]
EMB_A[12]/GP3[13]
107 EMB_BA[0]/GP7[1]
106 EMB_BA[1]/GP7[0]
EMB_A[8]/GP7[10]
EMB_A[9]/GP7[11]
103 EMB_A[0]/GP7[2]
102 EMB_A[1]/GP7[3]
101 EMB_A[2]/GP7[4]
100 EMB_A[3]/GP7[5]
EMB_A[4]/GP7[6]
EMB_A[5]/GP7[7]
EMB_A[6]/GP7[8]
EMB_A[7]/GP7[9]
121 AXR0[8]/GP3[8]
120 AXR0[7]/GP3[7]
131 AFSR0/GP3[12]
108 EMB_CS[0]
110 EMB_RAS
128 DVDD
119 DVDD
114 CVDD
109 DVDD
104 CVDD
DVDD
CVDD
DVDD
99
98
97
96
95
94
93
92
91
90
89
RSV2 133 88 EMB_SDCKE

USB0_VDDA12 134 87 DVDD
USB0_VDDA18 135 86 EMB_CLK
NC 136 85 EMB_WE/DQM[1]/GP5[14]
USB0_DP 137 84 EMB_D[8]/GP6[8]
USB0_DM 138 83 EMB_D[9]/GP6[9]
NC 139 82 EMB_D[10]/GP6[10]
USB0_VDDA33 140 81 DVDD
PLL0_VDDA 141 80 EMB_D[11]/GP6[11]
PLL0_VSSA 142 79 EMB_D[12]/GP6[12]
OSCIN 143 78 EMB_D[13]/GP6[13]
OSCVSS 144 77 CVDD
OSCOUT 145 76 EMB_D[14]/GP6[14]
RESET 146 75 DVDD
CVDD 147 74 EMB_D[15]/GP6[15]
RTC_XI 148 73 EMB_D[0]/GP6[0]
RTC_CVDD 149 72 EMB_D[1]/GP6[1]
TRST 150 71 DVDD
DVDD 151 70 EMB_D[2]/GP6[2]
TMS 152 69 CVDD
TDI 153 68 EMB_D[3]/GP6[3]
CVDD 154 67 CVDD
TCK 155 66 EMB_D[4]/GP6[4]
TDO 156 65 DVDD
GP7[14] 157 64 EMB_D[5]/GP6[5]
DVDD 158 63 EMB_D[6]/GP6[6]
CVDD 159 62 EMB_D[7]/GP6[7]
AHCLKX1/EPWMQB/GP3[14] 160 61 CVDD
CVDD 161 60 EMB_WE_DQM[0]/GP5[15]
ACLKX1/EPWMQA/GP3[15] 162 59 EMB_WE
AFSX1/EPWMSYNCI/EPWMSYNC0/GP4[10] 163 58 DVDD
DVDD 164 57 EMB_CAS
ACLKR1/ECAP2/APWM2/GP4[12] 165 56 CVDD
AFSR1/GP4[13] 166 55 EMA_WE]/UHPI_HRW/AXR0[12]/GP2[3]/BOOT[14]
CVDD 167 54 EMA_D[7]/MMCSD_DAT[7]/UHPI_HD[7]/GP0[7]/BOOT[13]
AXR1[8]/EPWM1A/GP4[8] 168 53 DVDD
AXR1[7]/EPWM1B/GP4[7] 169 52 EMA_D[6]/MMCSD_DAT[6]/UHPI_HD[6]/GP0[6]
AXR1[6]/EPWM2A/GP4[6] 170 51 EMA_D[5]/MMCSD_DAT[5]/UHPI_HD[5]/GP0[5]
AXR1[5]/EPWM2B/GP4[5] 171 50 CVDD
DVDD 172 49 EMA_D[4]/MMCSD_DAT[4]/UHPI_HD[4]/GP0[4]
AXR1[4]/EQEP1B/GP4[4] 173 48 EMA_D[3]/MMCSD_DAT[3]/UHPI_HD[3]/GP0[3]
AXR1[3]/EQEP1A/GP4[3] 174 47 DVDD
AXR1[2]/GP4[2] 175 46 EMA_D[2]/MMCSD_DAT[2]/UHPI_HD[2]/GP0[2]
AXR1[1]/GP4[1] 176 45 EMA_D[1]/MMCSD_DAT[1]/UHPI_HD[1]/GP0[1]
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
EMA_A[3]/GP1[3] 32
DVDD 33
EMA_A[4]/GP1[4] 34
EMA_A[5]/GP1[5] 35
EMA_A[6]/GP1[6] 36
EMA_A[7]/GP1[7] 37
CVDD 38
EMA_A[8]/GP1[8] 39
EMA_A[9]/GP1[9] 40
41
42
43
EMA_D[0]/MMCSD_DAT[0]/UHPI_HD[0]/GP0[0]/BOOT[12] 44
1
2
3
4
5
6
7
8
9
DVDD
CVDD
DVDD
CVDD
DVDD
EMA_BA[0]/GP1[14]
EMA_BA[1]/UHPI_HHWIL/GP1[13]
EMA_A[10]/GP1[10]
CVDD
EMA_A[0]/GP1[0]
EMA_A[11]/GP1[11]
EMA_A[12]/GP1[12]
DVDD
AXR1[0]/GP4[0]
UART0_RXD/I2C0_SDA/TM64P0_IN12/GP5[8]/BOOT[8]
UART0_TXD/I2C0_SCL/TM64P0_OUT12/GP5[9]/BOOT[9]
AXR1[10]/GP5[10]
AXR1[11]/GP5[11]
SPI1_ENA/UART2_RXD/GP5[12]
SPI1_SCS[0]/UART2_TXD/GP5[13]
SPI0_SCS[0]/UART0_RTS/EQEP0B/GP5[4]/BOOT[4]
SPI0_CLK/EQEP1I/GP5[2]BOOT[2]
SPI0_ENA/UART0_CTS/EQEP0A/GP5[3]/BOOT[3]
SPI1_SOMI[0]/I2C1/SCL/GP5[5]BOOT[5]
SPI1_SIMO[0]/I2C1/SDA/GP5[6]BOOT[6]
SPI1_CLK/EQEP1S/GP5[7]BOOT[7]
SPI0_SOMI[0]/EQEP0I/GP5[0]BOOT[0]
SPI0_SIMO[0]/EQEP0S/GP5[1]BOOT[1]
EMA_WAIT[0]/UHPI_HRDY/GP2[10]
EMA_CS[3]/AMUTE2/GP2[6]
EMA_OE/UHPI_HDS1/AXR0[13]/GP2[7]
EMA_CS[2]/UHPI_HCS/GP2[5]/BOOT[15]
EMA_A[1]/MMCSD_CLK/UHPI/HCNTL0/GP1[1]
EMA_A[2]/MMCSD_CMD/UHPI/HCNTL1/GP1[2]
86
RX-A3030/RX-V3075
Pin TYPE PULL

Function Name Detail of Function
RX-A3030/RX-V3075
No. (1) (2)
1 AXR1[0]/GP4[0] I/O IPD McASP1 serial data
2 UART0_RXD/I2C0_SDA/TM64P0_IN12/GP5[8]/ I IPU BOOT[8]
BOOT[8] I IPU UART0 receive data
I/O IPU I2C0 serial data
I IPU Timer0 lower input
3 UART0_TXD/I2C0_SCL/TM64P0_OUT12/GP5[9]/ I IPU BOOT[9]
BOOT[9] O IPU UART0 transmit data
I/O IPU I2C0 serial clock
O IPU Timer0 lower output
4 AXR1[10]/GP5[10] I/O IPU McASP1 serial data
5 DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
7 SPI1_ENA /UART2_RXD/GP5[12] I/O IPU SPI1 enable
I IPU UART2 receive data
8 SPI1_SCS[0] /UART2_TXD/GP5[13] I/O IPU SPI1 chip select
O IPU UART2 transmit data
9 SPI0_SCS[0] /UART0_RTS/EQEP0B/GP5[4]/BOOT[4] I/O IPU SPI0 chip select
I IPU eQEP0B quadrature input
I IPU BOOT[4]
O IPU UART0 ready-to-send output
10 CVDD (Core supply) PWR 1.2-V core supply voltage pins
11 SPI0_CLK/EQEP1I/GP5[2]/BOOT[2] I/O IPD SPI0 clock
I IPD eQEP1 index
I IPD BOOT[2]
12 SPI0_ENA /UART0_CTS/EQEP0A/GP5[3]/BOOT[3] I/O IPU SPI0 enable
I IPU eQEP0A quadrature input
I IPU BOOT[3]
I IPU UART0 clear-to-send input
13 SPI1_SOMI[0]/I2C1_SCL/GP5[5]/BOOT[5] I/O IPU SPI1 data/slave-out-master-in
I IPU BOOT[5]
I/O IPU I2C1 serial clock
14 SPI1_SIMO[0]/I2C1_SDA/GP5[6]/BOOT[6] I/O IPU SPI1 data/slave-in-master-out
I IPU BOOT[6]
I/O IPU I2C1 serial Data
16 SPI1_CLK/EQEP1S/GP5[7]/BOOT[7] I/O IPD SPI1 clock
I IPD eQEP1 strobe
I IPD BOOT[7]
17 SPI0_SOMI[0]/EQEP0I/GP5[0]/BOOT[0] I/O IPD SPI0 data/slave-out-master-in
I IPD eQEP0 index
I IPD BOOT[0]
18 SPI0_SIMO[0]/EQEP0S/GP5[1]/BOOT[1] I/O IPD SPI0 data/slave-in-master-out
I IPD eQEP0 strobe
I IPD BOOT[1]
19 EMA_WAIT[0]/ UHPI_HRDY/GP2[10] I IPU EMIFA wait input/interrupt
I/O IPU UHPI ready
21 EMA_CS[3] /AMUTE2/GP2[6] O IPU EMIFA Async chip select
O IPU McASP2 mute output
22 EMA_OE /UHPI_HDS1/AXR0[13]/GP2[7] O IPU EMIFA output enable
I/O IPU UHPI data strobe
23 EMA_CS[2] /UHPI_HCS/GP2[5]/BOOT[15] O IPU EMIFA Async chip select
I IPU BOOT[15]
I/O IPU UHPI chip select
24 EMA_OE/UHPI_HDS1/AXR0[13]/GP2[7] I/O IPU McASP0 serial data
DVDD (I/O supply) PWR 3.3-V I/O supply voltage pins
25 EMA_BA[0]/ GP1[14] O IPU EMIFA bank address
26 EMA_BA[1]/ UHPI_HHWIL/GP1[13] O IPU EMIFA bank address
I/O IPU UHPI half-word identification control
87
RX-A3030/RX-V3075
Pin TYPE PULL

RX-A3030/RX-V3075
No. (1) (2)

27 EMA_A[10]/ GP1[10] O IPU EMIFA address bus
29 EMA_A[0]/ GP1[0] O IPD EMIFA address bus
30 EMA_A[1]/MMCSD_CLK/UHPI_HCNTL0/GP1[1] O IPU EMIFA address bus
I/O IPU UHPI access control
O IPU MMCSD_CLK
31 EMA_A[2]/MMCSD_CMD/UHPI_HCNTL1/GP1[2] O IPU EMIFA address bus
I/O IPU UHPI access control
I/O IPU MMCSD_CMD
44 EMA_D[0]/MMCSD_DAT[0]/UHPI_HD[0]/GP0[0]/ I/O IPU EMIFA data bus
BOOT[12] I IPU BOOT[12]
I/O IPU UHPI data bus
I/O IPU MMC/SD data
45 EMA_D[1]/MMCSD_DAT[1]/UHPI_HD[1]/GP0[1] I/O IPU EMIFA data bus
I/O IPU MMC/SD data
I/O IPU MMC/SD data
I/O IPU MMC/SD data
I/O IPU MMC/SD data
I/O IPU MMC/SD data
I/O IPU MMC/SD data
54 EMA_D[7]/MMCSD_DAT[7]/UHPI_HD[7]/GP0[7]/ I/O IPU EMIFA data bus
BOOT[13] I IPU BOOT[13]
I/O IPU MMC/SD data
55 EMA_WE /UHPI_HRW/AXR0[12]/GP2[3]/BOOT[14] O IPU EMIFA SDRAM write enable
I IPU BOOT[14]
I/O IPU UHPI read/write
I/O IPU McASP0 serial data
57 EMB_CAS O IPU EMIFB column address strobe
59 EMB_WE O IPU EMIFB write enable
60 EMB_WE_DQM[0] /GP5[15] O IPU EMIFB write enable/data mask for EMB_D.
88
RX-A3030/RX-V3075
Pin TYPE PULL

RX-A3030/RX-V3075
No. (1) (2)
62 EMB_D[7]/GP6[7] I/O IPD EMIFB SDRAM data bus
85 EMB_WE_DQM[1] /GP5[14] O IPU EMIFB write enable/data mask for EMB_D
86 EMB_CLK O IPU EMIF SDRAM clock
88 EMB_SDCKE I/O IPU EMIFB SDRAM clock enable
89 EMB_A[12]/GP3[13] O IPD EMIFB SDRAM row/column address bus
98 EMB_A[4]/GP7[6] O IPD EMIFB SDRAM row/column address
106 EMB_BA[1]/GP7[0] O IPU EMIFB SDRAM bank address
107 EMB_BA[0]/GP7[1] O IPU EMIFB SDRAM bank address
108 EMB_CS[0] O IPU EMIFB SDRAM chip select 0
110 EMB_RAS O IPU EMIFB SDRAM row address strobe
111 AXR0[0]/AFSR2/GP3[0] I/O IPD McASP0 serial data
O IPD McASP2 serial data
112 AXR0[1]/ACLKX2/GP3[1] I/O IPD McASP0 serial data
O IPD McASP2 transmit bit clock
113 AXR0[2]/AXR2[3]/GP3[2] I/O IPD McASP0 serial data
115 AXR0[3]/AXR2[2]/GP3[3] I/O IPD McASP0 serial data
89
RX-A3030/RX-V3075
Pin TYPE PULL

RX-A3030/RX-V3075
No. (1) (2)

116 AXR0[4]/ AXR2[1]/GP3[4] I/O IPD McASP0 serial data
117 AXR0[5]/AFSX2/GP3[5] I/O IPD McASP0 serial data
O IPD McASP2 transmit frame sync
118 AXR0[6]/ACLKR2/GP3[6] I/O IPD McASP0 serial data
I/O IPD McASP2 receive bit clock
122 UART1_RXD/AXR0[9]/GP3[9] I IPD UART1 receive data
(3) I/O IPD McASP0 serial data
123 UART1_TXD/AXR0[10]/GP3[10] O IPD UART1 transmit data
(3) I/O IPD McASP0 serial data
124 AXR0[11]/ AXR2[0]/GP3[11] I/O IPD McASP0 serial data
125 AHCLKX0/AHCLKX2/USB_REFCLKIN/GP2[11] I/O IPD McASP0 transmit master clock
O IPD McASP2 transmit master clock
I IPD USB_REFCLKIN. Optional 48 MHz clock input
126 ACLKX0/ECAP0/APWM0/GP2[12] I/O IPD Enhanced capture 0/input or auxiliary PWM 0 output
I/O IPD McASP0 transmit bit clock
127 AFSX0/GP2[13]/BOOT[10] I IPD BOOT[10]
I/O IPD McASP0 transmit frame sync
129 AHCLKR0/GP2[14]/BOOT[11] I IPD BOOT[11]
I/O IPD McASP0 receive master clock
130 ACLKR0/ECAP1/APWM1/GP2[15] I/O IPD Enhanced capture 1/input or auxiliary PWM 1 output
131 AFSR0/GP3[12] I/O IPD McASP0 receive frame sync
132 AMUTE1/EPWMTZ/GP4[14] I/O IPD eHRPWM0 trip zone input
I/O IPD eHRPWM1 trip zone input
I/O IPD eHRPWM2 trip zone input
O IPD McASP1 mute output
133 RSV2 PWR Reserved. For proper device operation, this pin must be tied directly to CVDD
134 USB0_VDDA12 (4) PWR USB0 PHY 1.2-V LDO output for bypass cap
135 USB0_VDDA18 PWR USB0 PHY 1.8-V supply input
136 NC
137 USB0_DP A USB0 PHY data plus
138 USB0_DM A USB0 PHY data minus
139 NC
140 USB0_VDDA33 PWR USB0 PHY 3.3-V supply
141 PLL0_VDDA PWR PLL analog VDD (1.2-V filtered supply)
142 PLL0_VSSA GND PLL analog VSS (for filter)
143 OSCIN I Oscillator input
144 OSCVSS GND Oscillator ground (for filter only)
145 OSCOUT O Oscillator output
146 RESET I Device reset input
148 RTC_XI I Low-frequency (32-kHz) oscillator receiver for real-time clock
149 RTC_CVDD PWR RTC module core power ( isolated from rest of chip CVDD)
150 TRST I IPD JTAG test reset
152 TMS I IPU JTAG test mode select
153 TDI I IPU JTAG test data input
155 TCK I IPU JTAG test clock
156 TDO O IPD JTAG test data output
157 GP7[14] (5) I/O IPD General-Purpose IO signal
90
RX-A3030/RX-V3075
Pin TYPE PULL

RX-A3030/RX-V3075
No. (1) (2)
160 AHCLKX1/EPWM0B/GP3[14] I/O IPD eHRPWM0 B output
I/O IPD McASP1 transmit master clock
162 ACLKX1/EPWM0A/GP3[15] I/O IPD eHRPWM0 A output
I/O IPD McASP1transmit bit clock
163 AFSX1/EPWMSYNCI/EPWMSYNCO/GP4[10] I/O IPD Sync input to eHRPWM0 module or sync output to external PWM
I/O IPD McASP1 transmit frame sync
165 ACLKR1/ECAP2/APWM2/GP4[12] I/O IPD enhanced capture 2/input or auxiliary PWM 2 output
166 AFSR1/GP4[13] I/O IPD McASP1 receive frame sync
168 AXR1[8]/EPWM1A/GP4[8] I/O IPD eHRPWM1 A (with high-resolution)
I/O IPD McASP1 serial data
169 AXR1[7]/EPWM1B/GP4[7] I/O IPD eHRPWM1 B
170 AXR1[6]/EPWM2A/GP4[6] I/O IPD eHRPWM2 A (with high-resolution)
171 AXR1[5]/EPWM2B/GP4[5] I/O IPD eHRPWM2 B
173 AXR1[4]/EQEP1B/GP4[4] I IPD eQEP1B quadrature input
174 AXR1[3]/EQEP1A/GP4[3] I IPD eQEP1A quadrature input
(1) I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.
Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the the signal name highlighted
in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured function supports
high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different types (ie., input versus
output), the table reflects the pin function direction for that particular peripheral.
(2) IPD = Internal Pulldown resistor, IPU = Internal Pullup resistor
(3) 122, 123 pin: As these signals are internally pulled down while the device is in reset, it is necessary to externally pull them high with resistors if UART1
boot mode is used.
(4) 134 pin: Core power supply LDO output for USB PHY. This pin must be connected via a 0.22-mF capacitor to VSS. When the USB peripheral is not
used, the USB_VDDA12 signal should still be connected via a 1-mF capacitor to VSS.
(5) 157 pin: GP7[14] is initially configured as a reserved function after reset and will not be in a predictable state. This signal will only be stable after
the GPIO configuration for this pin has been completed. Users should carefully consider the system implications of this pin being in an
unknown state after reset.
91
RX-A3030/RX-V3075
IC951: DM860A (DIGITAL (1) P.C.B.)

RX-A3030/RX-V3075
Network microprocessor
General Purpose
Security Engine Timing Engine
RESET, BOOT_SEL on-chip RAM CLOCKS
Reset, Boot, OTP 2 PLLs, 3 DCOs
64 kBytes
master DMA
AV0 Port slave
4xAudio, 1xVideo 2 Forwarding Units
I2S, I8S, DSD, video 64 Contexts
AV2 Port S ARM 926EJ-S

4xAudio
I2S, I8S, DSD 240 MHz
Y
I-cache 16 kByte
slave master
AV3 Port S D-cache 16 kByte
2xAudio I2S, I8S, DSD,
SPDIF
T
slave Interrupt Controller GPIO
AV4 Port Watchdog, 2 Timer
2xAudio I2S, I8S, DSD, E
SPDIF, ADAT
M RTSP Processor
160 MHz
stereo master
Audio PWM-DAC slave I-cache 16 kByte
TCM 48 kByte
Memory Bus, SD/SRAM and System slave

System Extension Extension Controller Audio Engine
B 160 MHz
master
slave slave I-cache 4 kByte
LCD LCD Controller U
TCM 10 kByte
USB 2.0 slave master Ethernet MAC

USB USB (R/SSS)MII
OTG
10/100 Mbps
PHY 8 kByte RAM
slave slave
UART 2 x UART-1 NAND FLASH NAND
slave slave
SPI SPI SSM Controller SSM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
VDD33 VSS33
A USBDN n.c. n.c. VDD33 RFCLKP RFRXQP RFRXIP HIGHZ SSMD0 SSMD4 SSMCMD RXD1 TDO TDI A0 A1 A
USBC USBC
VDD33 VSS33
B USBDP n.c. n.c. VSS RFCLKN RFRXQN RFRXIN TEST1 SSMD1 SSMD5 TXD1 RXD0 TMS SPICLK SPINCS1 A2 B
USBT USBT
VSS12 NRES12
C USBREXT USBXO USBXI VSS RREF n.c. n.c. SSMCLK SSMD2 SSMD6 TXD0 TCK SPINCS0 A3 A4 A5 C
USB OUT
VDD12 NRES33 NRES33 NRES12

D USBVBUS USBATST VDD33 VDD12 SSMWP SSMCP SSMD3 SSMD7 NRESET SPIDI SPIDO A6 A7 A8 D
USB OUT REF REF
VSS33 USBVB VDD12 VDD12 VDD12 VDD12

E USBID NC VDD33IO VDD33IO VDD33IO VDD33IO A9 A10 A11 A12 E
RTC USDRV CORE CORE CORE CORE
VDD33 VDD33 VDD12

F RTCXIN NC VDD33IO VSS VSS VSS VSS VSS VSS VSS VSS A13_RAS A14_CAS A15_BA0 A16_BA1 F
RTC PLL CORE
VDD12 VSS33 VDD12 A17_DQ A18_DQ

G RTCXOUT NC VDD33IO VSS VSS VSS VSS VSS VSS VSS VSS A19 A20 G
DCO PLL CORE M0 M1
VSS12 VSS12 VDD12 VDD12

H NC VSS VSS VSS VSS VSS VSS VSS VSS VDD33IO A21 A22 A23 NCS3 H
DCO PLL PLL CORE
VDD12
J PDOUT1 VCO1 XTALO NC VSS VSS VSS VSS VSS VSS VSS VSS VDD33IO NCS0 NCS1 NCS2 MEMCKE J
CORE
VDD12
K PDOUT0 VCO0 XTALI AOUTLP VDD33IO VSS VSS VSS VSS VSS VSS VSS VSS MEMCLK NWE NOE NWAIT K
CORE
VDD12
L AV0CLK AOUTLN AOUTRN AOUTRP VDD33IO VSS VSS VSS VSS VSS VSS VSS VSS D3 D2 D1 D0 L
CORE
AV0 AV0 AV0 AV0 VDD12

M VSS VSS VSS VSS VSS VSS VSS VSS VDD33IO D7 D6 D5 D4 M
CTRL0 CTRL1 CTRL2 DATA3 CORE
AV0 AV0 AV0 AV1 VDD12

N VSS VSS VSS VSS VSS VSS VSS VSS VDD33IO D11 D10 D9 D8 N
DATA2 DATA1 DATA0 DATA3 CORE
AV1 AV1 AV1 AV2 VDD12 VDD12 VDD12 VDD12

P VDD33IO VDD33IO VDD33IO VDD33IO FD0 FD1 D13 D12 P
DATA2 DATA1 DATA0 DATA3 CORE CORE CORE CORE
AV2 AV2 AV3 LCD

R AV2CLK AV3CLK LCDD11 LCDD7 LCDD3 VPP MIITXEN MIITXCLK MIIRXER MIICRS FD2 FD3 FD4 D14 R
CTRL1 DATA2 DATA1 CTRL0
AV2 AV2 AV3 AV3 LCD MII

T LCDD14 LCDD10 LCDD6 LCDD2 LCDCLK MIIITXER MIIRXCLK MIICOL FD5 FD6 FD7 D15 T
CTRL0 DATA1 CTRL1 DATA0 CTRL1 RXDV
AV2 AV3 AV4 LCD

U LCDD16 LCDD13 LCDD9 LCDD5 LCDD1 MIITXD0 MIITXD2 MIIRXD0 MIIRXD2 MIIMDIO NFCE0 FCLE NFWE NFRB U
DATA0 CTRL0 DATA1 CTRL2
AV4 LCD MIIPHY

V NC LCDD17 LCDD15 LCDD12 LCDD8 LCDD4 LCDD0 MIITXD1 MIITXD3 MIIRXD1 MIIRXD3 MIIMDC NFWP NFRE FALE V
DATA0 CTRL3 CLK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
92
RX-A3030/RX-V3075
AV-Port 0
RX-A3030/RX-V3075
Pin No. Function Name I/O Detail of Function
M4
N1 Audio/video data.
AV0DATA[3:0] I/O
N2 Several formats are supported.
N3
N4 Video data, together with AV0DATA[3:0]:
P1 AV0DATA[3:0] = video[3:0]
AV1DATA[3:0] I/O
P2 AV1DATA[3:0] = video[7:4]
P3
Data clock. Depending on the AV-Port 0 configuration, this clock is a bit- or byte-clock which is used to
L1 AV0CLK I/O
transmit or receive the AV0DATA[*] synchronously.
Configurable sync signal:
M1 AV0CTRL0 I/O Serial audio formats: LRCK input or output.
Video formats: PSYNC input or output.
M2 AV0CTRL1 I/O Serial audio formats: Master clock output.
Video formats: DVALID input or output.
M3 AV0CTRL2 I/O
Video formats: FSYNC input or output.
AV-Port 2
P4
R3 Audio data.
AV2DATA[3:0] I/O
T2 Several formats are supported.
U1
Data clock. Depending on the AV-Port 2 configuration this clock is a bit-clock which is used to transmit or
R1 AV2CLK I/O
receive the AV2DATA[*] synchronously.
T1 AV2CTRL0 I/O
Serial audio formats: LRCK input or output.
R2 AV2CTRL1 I/O
Serial audio formats: Master clock output.
AV-Port 3
R5 Audio data.
AV3DATA[1:0] I/O
T4 Several formats are supported.
Data clock. Depending on the AV-Port 3 configuration this clock is a bit-clock which is used to transmit or
R4 AV3CLK I/O
receive the AV3DATA[*] synchronously.
U2 AV3CTRL0 I/O
Serial audio formats: LRCK input or output.
T3 AV3CTRL1 I/O
Serial audio formats: Master clock output.
AV-Port 4
U3 Audio data.
AV4DATA[1:0] I/O
V2 Several formats are supported.
PWM-DAC
K4 AOUTLP O Left channel PWM output (positive).
L2 AOUTLN O Left channel PWM output (negative).
L4 AOUTRP O Right channel PWM output (positive).
L3 AOUTRN O Right channel PWM output (negative).
UART Interface
B14 RXD0 I UART-0 receive signal.
C13 TXD0 O UART-0 transmit signal.
A14 RXD1 I UART-1 receive signal.
B13 TXD1 O UART-1 transmit signal.
93
RX-A3030/RX-V3075
Serial Peripheral Interface (SPI)

RX-A3030/RX-V3075

D14 SPIDIN I SPI data receive.
D15 SPIDOUT O SPI data transmit.
B16 SPICLK I/O SPI clock.
Multi-master mode: Chip-select input (used to detect bus conflict).
C15 SPINCS0 I/O Master only mode: Chip-select 1 output.
Slave mode: Chip-select input.
Multi-master mode: Chip-select 2 output.
B17 SPINCS1 I/O Master only mode: Chip-select 2 output.
Slave mode: Not used.
External Memory Interface

T18
R18
P17
P18
N15
N16
N17
N18
D[15:0] I/O Data bus for external memory and peripheral access.
M15
M16
M17
M18
L15
L16
L17
L18
E18
E17
E16
E15
D18
D17
D16 A[12:0] O Address bus for external memory and peripheral access.
C18
C17
C16
B18
A18
A17
SRAM: Address output
F15 A13_RAS O
SDRAM: Row access strobe
F16 A14_CAS O
SDRAM: Column access strobe
F17 A15_BA0 O
SDRAM: Bank select
F18 A16_BA1 O
SDRAM: Bank select
G15 A17_DQM0 O
SDRAM: Data mask
G16 A18_DQM1 O
SDRAM: Data mask
H17
H16
H15 A[23:19] O Address bus for external memory and peripheral access.
G18
G17
94
RX-A3030/RX-V3075
RX-A3030/RX-V3075
H18 Chip select signals. The active memory range for NCS[n] (active low) can be configured.
J17 NCS[0] supports SRAM, can be used for booting.
J16 NCS[3:0] O NCS[1] supports SDRAM or SRAM.
J15 NCS[2] supports SRAM.
NCS[3] supports SRAM.
K17 NOE O Output enable, asserted (low) for read operations.
K16 NWE O Write enable, asserted (low) for write operations.
K18 NWAIT I External wait line. If NWAIT is asserted, memory access will be stalled. Can be configured as either low-
active (default) or high-active.
K15 MEMCLK O SDRAM system clock.
J18 MEMCKE O SDRAM clock enable.
NAND-Flash Interface
T17
T16
T15
R17
FD[7:0] I/O Bi-directional data bus.
R16
R15
P16
P15
V18 FALE O Address latch enable; pull-up/down defines boot mode.
U16 FCLE O Command latch enable; pull-up/down defines boot mode.
U15 NFCE0 O Chip-enable, low-active.
U18 NFRB I Ready/busy. NAND flash is busy when NFRB is low.
V17 NFRE O Read enable, low-active.
U17 NFWE O Write enable, low-active.
V16 NFWP O Write protect, low-active.
Ethernet MAC-Phy Interface (MII)

Pin No. Function Name I/O MII RMII SMII
U14 MIIDIO I/O Management data Management data
V14 MIIMDC O Management clock Management clock
V13 MIIRXD[3] I RxD 3 RxD 1
U13 MIIRXD[2] I RxD 2 RxD 0
V12 MIIRXD[1] I RxD 1 Rx-Sync
U12 MIIRXD[0] I RxD 0 RxD
T12 MIIRXCLK I Receive clock Receive clock
R13 MIIRXER I Receive error Receive error
T14 MIIRXDV I Receive data valid Carrier sense/data valid
V11 MIITXD[3] O TxD 3 TxD 1
U11 MIITXD[2] O TxD 2 TxD 0
V10 MIITXD[1] O TxD 1 Tx-Sync
U10 MIITXD[0] O TxD 0 TxD
R12 MIITXCLK I Transmit clock Transmit clock
T11 MIITXER O Transmit error
R11 MIITXEN O Transmit data enable Transmit data enable
T13 MIICOL I MII ethernet collision
R14 MIICRS I MII carrier sense
V15 MIIPHYCLK O 25.000 MHz clock 50.000 MHz clock 125.000 MHz clock
95
RX-A3030/RX-V3075
USB 2.0 OTG

RX-A3030/RX-V3075

B1 USBD+ I/O Positive data line that is connected to the serial USB cable.
A1 USBD I/O Negative data line that is connected to the serial USB cable.
E2 USBID I USB ID pin of mini-AB receptacle.
C2 USBREXT I External bias resistor (2K7, 1%); connect resistor to VSSUSB.
D2 USBVBUS I VBUS voltage sense.
E3 USBVBUSDRV O Control signal to control VBUS 5V voltage source.
C4 USBXTALI I Oscillator circuit input for a 24.000 MHz crystal (optional).
Without external crystal, pull this pin to GND.
C3 USBXTALO O Oscillator circuit output for a 24.000 MHz crystal (optional).
Without external crystal, leave this pin open.
D3 USBATST Do not connect.
Power-on Reset Pins

D6 NRES12REF I Voltage reference input. NRES12OUT is release when this input voltage exceeds VTH12.
C5 NRES12OUT O Open-drain reset (active low) for 1.2V core power supply.
D5 NRES33REF I Voltage reference input. NRES33OUT is release when this input voltage exceeds VTH33.
D4 NRES33OUT O Open-drain reset (active low) for 3.3V core power supply
Real-Time Clock (RTC) Pins (RTC is Not Supported)

F2 RTCXIN I No connection. Leave this pin open circuit.
G2 RTCXOUT O No connection. Leave this pin open circuit.
F1 VDD33RTC Power No connection. Leave this pin open circuit.
E1 VSS33RTC Power Ground (0 V) for RTC
LCD Interface
LCD STN monochr. LCD STN color

Pin No. Function Name I/O TFT Mode LCD STN monochr. LCD STN color
(double) (bias)
V3 LCDD[17] O RED5
U4 LCDD[16] O RED4
V4 LCDD[15] O RED3
T5 LCDD[14] O RED2
U5 LCDD[13] O RED1
V5 LCDD[12] O (RED0)
R6 LCDD[11] O GREEN5
T6 LCDD[10] O GREEN4
U6 LCDD[9] O GREEN3
V6 LCDD[8] O GREEN2
R7 LCDD[7] O GREEN1 DATAHIGH3 DATA7 DATA7
T7 LCDD[6] O GREEN0 DATAHIGH2 DATA6 DATA6
U7 LCDD[5] O BLUE5 DATAHIGH1 DATA5 DATA5
V7 LCDD[4] O BLUE4 DATAHIGH0 DATA4 DATA4
R8 LCDD[3] O BLUE3 DATA3 DATALOW3 DATA3 DATA3
T8 LCDD[2] O BLUE2 DATA2 DATALOW2 DATA2 DATA2
U8 LCDD[1] O BLUE1 DATA1 DATALOW1 DATA1 DATA1
V8 LCDD[0] O (BLUE0) DATA0 DATALOW0 DATA0 DATA0
T10 LCDCLK O Byte clock CL2 CL2 CL2 CL2
V9 LCDCTRL[3] O Display off Display off Display off Display off Display off
U9 LCDCTRL[2] O Vsync FLM FLM FLM FLM
T9 LCDCTRL[1] O HSync CL1 CL1 CL1 CL1
R9 LCDCTRL[0] O DVALID M/Bias
96
RX-A3030/RX-V3075
SSM Interface
RX-A3030/RX-V3075
D12
C12
B12
A12
SSMD[7:0] I/O Data lines.
D11
C11
B11
A11
C10 SSMCLK O Clock output.
A13 SSMCMD O Command output.
D10 SSMCP I Card power input (high = off).
D9 SSMWP I Write protect input (low = protect).
External PLL Pins

J2 External oscillator inputs, typically coming from an external VCO. Together with the external loop-filter and
VCO[1:0] I
K2 the internal clock dividers, each PDOUT/VCO pair can form a complete PLL.
J1 Phase discriminator outputs. These signals are charge-pump type outputs.
PDOUT[1:0] O
K1 Each of them can be used to feed the loop-filter of a PLL structure.
Global Pins
Reset (active low). When asserted, the chip is placed in the reset state and the peripheral pins are
configured as inputs. After deassertion of NRESET, the chip is clocked by XTALI and starts booting from the
D13 NRESET I port configured by the FCLE, FALE pins.
The NRESET signal must be asserted after power-up.
K3 XTALI I Oscillator circuit input. Internal system clock will be derived from XTALI (internal clock multiplier).
J3 XTALO O Oscillator circuit output.
C7 RREF I Reference current. Connect a 3.0 k-ohms 1% resistor to GND.
B10 TEST1 I Reserved. Connect to VDD for normal operation.
A10 HIGHZ I Reserved. Connect to VDD for normal operation.
E4
F4
G4
H4
J4
V1
n.c. Pins must be left unconnected (18x).
A4
A5
B4
B5
C8
C9
JTAG Interface
B15 TMS I JTAG mode select.
C14 TCK I JTAG clock.
A16 TDI I JTAG serial data input.
A15 TDO O JTAG serial data output.
97
RX-A3030/RX-V3075
Power Supply Pins

RX-A3030/RX-V3075
Pin No. Function Name Detail of Function Pin No. Function Name Detail of Function
A6 K13
E8 L6
E9 L7
E12 L8
E13 L9
F5 L10
G5 L11
H14 L12
J14 L13
VDD33 I/O power supply (+3.3 V).
K5 M6
L5 M7
M14 M8
N14 M9
P6 M10 VSS Ground (0 V).
P7 M11
P10 M12
P11 M13
D7 N6
F6 N7
F7 N8
F8 N9
F9 N10
F10 N11
F11 N12
F12 N13
F13 B6
G6 C6
G7 R10 VPP
G8 A2
VDD33USB
G9 B2 Power supply (+3.3 V) for USB interface.
G10 A3 Ground (0 V).
VSS33USB
G11 B3
G12 F3 VDD33PLL Power supply (+3.3V) for PLL.
G13 G3 VSS33PLL Ground (0 V).
H6 E6
H7 E7
H8 E10
H9 VSS Ground (0 V). E11
H10 F14
H11 G14
H12 H5
H13 J5
J6 K14 VDD12 Power supply (+1.2V).
J7 L14
J8 M5
J9 N5
J10 P8
J11 P9
J12 P12
J13 P13
K6 D8
K7 D1 VDD12USB Power supply (+1.2V) for USB interface.
K8 C1 VSS12USB Ground (0 V).
K9 H3 VDD12PLL Power supply (+1.2V) for PLL.
K10 H2 VSS12PLL Ground (0 V).
K11 G1 VDD12DCO Power supply (+1.2V) for DCO.
K12 H1 VSS12DCO Ground (0 V).
98
RX-A3030/RX-V3075
IC79: R5F6416MADFE (DIGITAL (1) P.C.B.)
RX-A3030/RX-V3075
Microprocessor
8 8 8 8 8 8 8 8
Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6 Port P7
Port P8
Peripheral functions
7
Timer: A/D converter: Clock generator:
Timer A16 bits 5 timers 10 bits 1 circuit 4 circuits
Timer B16 bits 6 timers Standard: 10 inputs - XIN-XOUT
Maximum: 34 inputs - XCIN-XCOUT
P8_5
Three-phase motor - On-chip oscillator
controller - PLL frequency synthesizer
D/A converter:
Serial interface: 8 bits 2 channels
Watchdog timer:
11 channels
Port P9
X-Y converter: 15 bits
16 bits 16 bits
8
Multi-master I2C-bus DMAC
interface: CRC calculator (CCITT)
1 channel X16 + X12 + X5 + 1 DMAC II
Port P10
Intelligent I/O R32C/100 Series Microprocessor Core Memory
8
Time Measurement: 16
R2R0 ROM
Wave generation: 24 R2R0
R3R1 FLG
Serial interface: R3R1 INTB
Port P11
R6R4
- Variable-length R6R4
R7R5 ISP RAM
R7R5
A0 USP
synchronous serial I/O A0 PC
8
- IEBus A1
A1
A2 SVF
A2 SVP Multiplier
A3
A3
FB VCT
Port P12
FB
SB
SB Floating-point unit
8
Port P19 Port P18 Port P17 Port P16 Port P15 Port P14 P14_1 Port P13
8 8 8 8 8 5 8
96 RXD10
95 TXD10
97 CLK10
112 P12_2
111 P12_3
110 P12_4
106 P16_0
98 P16_4
92 P11_5
90 P11_6
104 RXD9
114 TXD6
103 TXD9
113 CLK6
105 CLK9
131 D[10]
130 D[11]
129 D[12]
128 D[13]
127 D[14]
126 D[15]
108 A[10]
107 A[11]
102 A[12]
101 A[13]
100 A[14]
99 A[15]
94 A[16]
93 A[17]
91 A[18]
89 A[19]
115 VCC
117 VSS
132 D[9]
125 A[0]
124 A[1]
123 A[2]
122 A[3]
121 A[4]
120 A[5]
119 A[6]
118 A[7]
116 A[8]
109 A[9]
D[8] 133 88 A[20]

D[7] 134 87 A[21]
D[6] 135 86 A[22]
D[5] 136 85 CS0
D[4] 137 84 P19_2
P19_1 138 83 P17_0
P11_4 139 82 P17_1
P19_0 140 81 P17_2
P11_3 141 80 P17_3
P11_2 142 79 P19_3
P11_1 143 78 P12_5
P11_0 144 77 P12_6
P18_7 145 76 P12_7
P18_6 146 75 WR/P5_0
P18_5 147 74 NC(BC1)
P18_4 148 73 RD
P18_3 149 72 NC(BCLK)
P18_2 150 71 P13_0
D[3] 151 70 P13_1
D[2] 152 69 VCC
D[1] 153 68 P13_2
D[0] 154 67 VSS
P15_7 155 IC83 66 P13_3
P15_6 156 65 CS1
P15_5 157
R5F6416MADFE 64 P5_5
P15_4 158 63 CS2
P15_3 159 62 CS3
P15_2 160 61 P19_4
IIO0_1 161 60 ISTXD2
VSS 162 59 ISRXD2
P15_0 163 58 ISCLK2
VCC 164 57 P13_7
P10_7 165 56 P19_5
AN_6 166 55 P6_0
AN_5 167 54 CLK0
P10_4 168 53 RXD0
P10_3 169 52 TXD0
AN_2 170 51 P6_4
AN_1 171 50 CLK1
AVSS 172 49 P11_7
P10_0 173 48 RXD1
VREF 174 47 P14_7
AVCC 175 46 TXD1
SCL4/RXD4 176 45 SDA2
P19_6 10
INT7 11
INT6 12
P14_3 13
VDC0 14
P14_1 15
VDC1 16
NSD 17
CNVSS 18
P8_7 19
P8_6 20
RESET 21
XOUT 22
VSS 23
XIN 24
VCC 25
NMI 26
INT2 27
INT1 28
INT0 29
TA4IN 30
SCL5 31
P18_1 32
P18_0 33
TA3IN 34
SDA5 35
TA2IN 36
P7_4 37
P17_7 38
P17_6 39
P17_5 40
P17_4 41
TA2IN 42
P7_2 43
SCL2 44
SDA4/TXD4 1
P9_5 2
P9_4 3
DA0 4
SDA3 5
SCL3 6
P9_0 7
P19_7 8
INT8 9
99
RX-A3030/RX-V3075
I/O
RX-A3030/RX-V3075
Pin
Port Name Function Name Related Power Supply Detail of Function
No.
OFF ON
TUN_SDA PRY O I/O Tuner I2C data
1 SRXD4/SDA4/TXD4/ANEX1/P9_6
HDR_MOSI PRY O O HD radio transmission data
2 CLK4/ANEX0/P9_5 VOL1_SCK PRY/DSP_PON O O VOL1 (R2A15220FP #1) communication clock
N_CTS4/N_N_RTS4/N_SS4/TB4IN/
3 VOL_MOSI PRY/DSP_PON O O VOL1/VOL2 communication data
DA1/P9_4
N_CTS3/N_N_RTS3/N_SS3/TB3IN/
4 AMP_LMT PRY I O Limiter control
DA0/P9_3
IEOUT/ISTXD2/OUTC2_0/SRXD3/
5 DAC1_SDA DAC_PON O I/O DAC1 I2C data (for F, C, SR, SB, SW)
SDA3/TXD3/TB2IN/P9_2
IEIN/ISRXD2/STXD3/SCL3/RXD3/
6 DAC1_SCL DAC_PON O O DAC1 I2C clock (for F, C, SR, SB, SW)
TB1IN/P9_1
7 CLK3/TB0IN/P9_0 VOL2_SCK PRY/DSP_PON O O VOL2 (R2A15220FP #2) communication clock
8 P19_7 MT_N_HP +3.3S_PON O O Mute headphone
9 N_INT8/P14_6 HAU_INT HDMI_PON O I Mute signal from HDMI, RX1 and RX2
10 P19_6 HRX1_MT HDMI_PON O I Mute signal from HDMI RX1 (for HAU_N_INT distinction)
11 N_INT7/P14_5 HTX1_N_INT HDMI_PON O I HDMI TX CEC interrupt
12 N_INT6/P14_4 PWR_DET AC I I AC power detect
13 P14_3 FLD_N_CS FLD_PON O O FLD chip select
14 VDC0 VDC0 ---
15 P14_1 (for exclusive use of the input) I_PRT PRY I I Current protection
16 VDC1 VDC1 ---
17 NSD NSD Debugger
18 CNVSS DBG_CNVSS ---
19 XCIN/P8_7 MIC_N_DET DSP_PON O I Microphone detection
20 XCOUT/P8_6 PD_LED PRY O O Pure direct LED
21 RESET MCPU_N_RST ---
22 XOUT XOUT ---
23 VSS VSS ---
24 XIN XIN ---
25 VCC VCC ---
26 NMI/P8_5 NMI ---
27 N_INT2/P8_4 WAKEUP_INT AC O I Power switch, MISO interrupt of RS-232C (sleep return)
28 N_INT1/P8_3 REM_IN2 AC O I Remote control pulse input 2
29 N_INT0/P8_2 REM_IN1 AC O I Remote control pulse input 1
UD0B/UD1B/IIO1_5/N_RTS5/N_CTS5/ TUN_N_INT PRY O I Interrupt from tuner
30
N_SS5/U/TA4IN/P8_1 --- AC O O No used
UD0A/UD1A/RXD5/SCL5/STXD5/U/
31 HDMI_SCL HDMI_PON O O HDMI 400k I2C clock
TA4OUT/P8_0
32 P18_1 HSW2_N_INT HDMI_PON O I ADV7630 (2) interrupt
33 P18_0 HSW1_N_INT HDMI_PON O I ADV7630 (1) interrupt
34 UD0B/UD1B/IIO1_4/CLK5/TA3IN/P7_7 FHDMI_N_INT HDMI_PON O I Front HDMI interrupt
UD0A/UD1A/IIO1_3/N_RTS8/N_CTS8/
35 HDMI_SDA HDMI_PON O I/O HDMI 400k I2C data
TXD5/SDA5/SRXD5/TA3OUT/P7_6
36 IIO1_2/RXD8/W/TA2IN/P7_5 DAU_N_INT DSP_PON O I Interrupt from DIR1, DIR2 and DSP
37 IIO1_1/CLK8/W/TA2OUT/P7_4 DIR2_N_INT DSP_PON O I Interrupt from DIR2 (for DAU_N_INT distinction)
38 P17_7 ISEL_RA AC I I Input selector A
39 P17_6 ISEL_RB AC I I Input selector B
40 P17_5 VOL_RA AC I I Volume A
41 P17_4 VOL_RB AC I I Volume B
IIO1_0/TXD8/N_SS2/N_RTS2/N_CTS2/
42 HRX_N_INT HDMI_PON O I HDMI RX (ADV7619) interrupt
V/TA1IN/P7_3
43 CLK2/V/TA1OUT/P7_2 NCPU_SPI_REQ NCPU_PON O I BridgeCO request
MSCL/IEIN/ISRXD2/OUTC2_2/IIO1_7/
44 DV_SCL HDMI_PON O O D-VIDEO/A-VIDEO/F-HDMI 400k I2C clock
STXD2/SCL2/RXD2/TA0IN/TB5IN/P7_1
TA0OUT/TXD2/SDA2/SRXD2/IIO1_6/
45 DV_SDA HDMI_PON O I/O D-VIDEO/A-VIDEO/F-HDMI 400k I2C data
OUTC2_0/ISTXD2/IEOUT/MSDA/P7_0
46 TXD1/SDA1/SRXD1/P6_7 232C_DBG_MOSI AC O O RS-232C transmission data / Debug / E8a
47 P14_7 DSP_PON DSP_PON O O DSP power supply
100
RX-A3030/RX-V3075
I/O
RX-A3030/RX-V3075
Pin
No.
OFF ON
48 RXD1/SCL1/STXD1/P6_6 232C_DBG_MISO AC O I RS-232C reception data / Debug / E8a
49 P11_7 --- AC O O No used
50 CLK1/P6_5 DBG_SCK AC O I E8a
N_CTS1/N_RTS1/N_SS1/OUTC2_1/
51 DBG_BUSY AC O O E8a
ISCLK2/P6_4
52 TXD0/SDA0/SRXD0/P6_3 DAC2_SDA DAC_PON O I/O DAC2 I2C data (for FP, RP, SW)
53 TB2IN/RXD0/SCL0/STXD0/P6_2 DAC2_SCL DAC_PON O O DAC2 I2C clock (for FP, RP, SW)
54 TB1IN/CLK0/P6_1 SEL_N_MCK AC O O MCLK source select of ESS DAC / H: crystal, L: DA_MCK
55 TB0IN/N_CTS0/N_RTS0/N_SS0/P6_0 NCPU_SPI_RDY NCPU_PON O I BridgeCO data ready
56 P19_5 --- AC O O No used
57 D31/OUTC2_7/P13_7 DSP1_N_RST DSP_PON O O DSP1 reset
58 D30/OUTC2_1/ISCLK2/P13_6 --- Serial spare
59 D29/OUTC2_2/ISRXD2/IEIN/P13_5 --- Serial spare
60 D28/OUTC2_0/ISTXD2/IEOUT/P13_4 --- Serial spare
61 P19_4 EEP_N_CS AC O O EEPROM chip select
62 RDY/CS3/N_CTS7/N_RTS7/P5_7 FPGA_N_CS HDMI_PON O B External bus FPGA chip select
63 ALE/CS2/RXD7/P5_6 DFF2_N_CS AC O B External bus DFF2 chip select
64 HOLD/CLK7/P5_5 DBG_EPM AC I I E8a
65 HLDA/CS1/TXD7/P5_4 DFF1_N_CS AC O B External bus DFF1 chip select
66 D27/OUTC2_3/P13_3 DSP2_N_SPIRDY DSP_PON O I DSP2 SPI ready
67 VSS VSS ---
68 D26/OUTC2_6/P13_2 DSP1_N_SPIRDY DSP_PON O I DSP1 SPI ready
69 VCC VCC ---
70 D25/OUTC2_5/P13_1 DSP2_N_CS DSP_PON O O DSP2 chip select
71 D24/OUTC2_4/P13_0 DSP1_N_CS DSP_PON O O DSP1 chip select
72 CLKOUT/BCLK/P5_3 NC(BCLK) AC O B External bus
73 RD/P5_2 MCBUS_N_RD AC O B External bus
74 WR1/BC1/P5_1 NC(BC1) AC O B External bus
MCBUS_N_WR HDMI_PON I B External bus
75 WR0/WR/P5_0
DBG_N_CE AC I I E8a
76 D23/P12_7 MT_DA DSP_PON O O Mute digital audio
77 D22/P12_6 DIR1_N_CS DSP_PON O O DIR1 chip select
78 D21/P12_5 DIR_N_RST DSP_PON O O DIR reset
79 P19_3 DIR2_N_CS DSP_PON O O DIR2 chip select
80 P17_3 DIR1_N_INT DSP_PON O I Interrupt from DIR1 (for DAU_N_INT distinction)
81 P17_2 HSW_N_CS HDMI_PON O O HDMI SW chip select / L=SW1, H=SW2
82 P17_1 NCPU_PON NCPU_PON O O NET / USB power supply
83 P17_0 NCPU_VBUSDRV NCPU_PON O I USB VBUS drive
84 P19_2 USB_VBUS_PON NCPU_PON O O USB VBUS power supply control
85 CS0/A23/TXD6/SDA6/SRXD6/P4_7 FLASH_N_CS AC O O External bus flash ROM chip select
86 CS1/A22/RXD6/SCL6/STXD6/P4_6 A[22] AC O B External bus
87 CS2/A21/CLK6/P4_5 A[21] AC O B External bus
CS3/A20/N_CTS6/N_RTS6/N_SS6/
88 A[20] AC O B External bus
P4_4
A19/TXD3/SDA3/SRXD3/OUTC2_0/
ISTXD2/IEOUT/P4_3
90 P11_6 ZTX_AUSEL1 AC O O Sound switching 1 to zone TX
A18/RXD3/SCL3/STXD3/ISRXD2/IEIN/
P4_2
92 P11_5 DFF_FROM_N_RST AC O O Reset of DFF and external ROM
93 A17/CLK3/P4_1 A[17] AC O B External bus
94 A16/N_CTS3/N_RTS3/N_SS3/P4_0 A[16] AC O B External bus
95 P16_7/TXD10 EX_MOSI AC O O FL/EEPROM transmission data
96 P16_6/RXD10 EEP_MISO AC O I EEPROM reception data
97 P16_5/CLK10 EX_SCK AC O O FL/EEPROM communication clock
98 P16_4/N_CTS10/N_RTS10 NCPU_AMUTE NCPU_PON O I Mute signal from BridgeCO
99 A15/[A15/D15]/TA4IN/U/P3_7 A[15] AC O B External bus
100 A14/[A14/D14]/TA4OUT/U/P3_6 A[14] AC O B External bus
101
RX-A3030/RX-V3075
I/O
RX-A3030/RX-V3075
Pin
No.
OFF ON
101 A13/[A13/D13]/TA2IN/W/P3_5 A[13] AC O B External bus
102 A12/[A12/D12]/TA2OUT/W/P3_4 A[12] AC O B External bus
103 P16_3/TXD9 NCPU_SPI_MOSI NCPU_PON O O Data (master out slave in)
104 P16_2/RXD9 NCPU_SPI_MISO NCPU_PON O I Data (master in slave out)
105 P16_1/CLK9 NCPU_SPI_SCK NCPU_PON O O Clock (master out slave in)
106 P16_0/N_CTS9/N_RTS9 NCPU_N_RST NCPU_PON O O Network microprocessor reset
107 A11/[A11/D11]/TA1IN/V/P3_3 A[11] AC O B External bus
108 A10/[A10/D10]/TA1OUT/V/P3_2 A[10] AC O B External bus
109 A9/[A9/D9]/TA3OUT/UD0B/UD1B/P3_1 A[9] AC O B External bus
110 D20/P12_4 AD_SEL_A +3.3S_PON O O AD select A
111 D19/N_CTS6/N_RTS6/N_SS6/P12_3 AD_SEL_B +3.3S_PON O O AD select B
112 D18/RXD6/SCL6/STXD6/P12_2 AD_SEL_C +3.3S_PON O O AD select C
113 D17/CLK6/P12_1 FPGA_SCK HDMI_PON O O FPGA clock (at Boot)
114 D16/TXD6/SDA6/SRXD6/P12_0 FPGA_MOSI HDMI_PON O O FPGA transmission data (at Boot)
115 VCC VCC ---
116 A8/[A8/D8]/TA0OUT/UD0A/UD1A/P3_0 A[8] AC O B External bus
117 VSS VSS ---
118 A7/[A7/D7]/AN2_7/P2_7/TXD10 A[7] AC O B External bus
119 A6/[A6/D6]/AN2_6/P2_6/RXD10 A[6] AC O B External bus
120 A5/[A5/D5]/AN2_5/P2_5/CLK10 A[5] AC O B External bus
A4/[A4/D4]/AN2_4/P2_4/N_CTS10/N_
RTS10
122 A3/[A3/D3]/AN2_3/P2_3/TXD9 A[3] AC O B External bus
123 A2/[A2/D2]/AN2_2/P2_2/RXD9 A[2] AC O B External bus
A1/[A1/D1]/BC2/[BC2/D1]/AN2_1/P2_1/
CLK9
A0/[A0/D0]/BC0/[BC0/D0]/AN2_0/P2_0/
N_CTS9/N_RTS9
126 D15/N_INT5/IIO0_7/IIO1_7/P1_7 D[15] AC I B External bus
129 D12/IIO0_4/IIO1_4/P1_4 D[12] AC I B External bus
133 IIO0_0/IIO1_0/D8/P1_0 D[8] AC I B External bus
134 AN0_7/D7/P0_7 D[7] AC I B External bus
138 P19_1 FPGA_N_CFG HDMI_PON O O FPGA nCONF
139 WR3/BC3/P11_4 FPGA_N_STA HDMI_PON I I FPGA nSTATUS
140 P19_0 FPGA_CDONE HDMI_PON I I FPGA CONF DONE
IIO1_3/N_RTS8/N_CTS8/WR2/CS3/
141 DIAG_CHECK AC O O Diag inspection result output / OK=High, NG=Low
P11_3
142 IIO1_2/RXD8/CS2/P11_2 NDAC_N_MT DSP_PON O O Net zone DAC mute
143 IIO1_1/CLK8/CS1/P11_1 MT_N_Z3 +3.3S_PON O O Mute Z3/RP (preout)
144 IIO1_0/TXD8/CS0/P11_0 NCPU_SPI_N_CS NCPU_PON O O Network microprocessor SPI chip select
145 P18_7 MT_N_F_MI +3.3S_PON O O Mute front/Z2/Z3/RP (main in)
146 P18_6 MT_N_Z2 +3.3S_PON O O Mute Z2/FP (preout)
147 P18_5 MT_N_SB_PO +3.3S_PON O O Mute SRB (preout)
148 P18_4 MT_N_MZ +3.3S_PON O O Mute main zone (HP, Preout (C, SR, SW), main in (C, SR))
149 P18_3 MT_N_EX1_MI +3.3S_PON O O Mute SP1 (BA/Z2/Z3/FP main in)
150 P18_2 MT_N_SB_MI +3.3S_PON O O Mute SB/Z2/Z3 (Main in)
102
RX-A3030/RX-V3075
I/O
RX-A3030/RX-V3075
Pin
No.
OFF ON
IIO0_7/N_RTS6/N_CTS6/N_SS6/
155 SVID_DET VID_PON I I S-video detect
AN15_7/P15_7
156 IIO0_6/CLK6/AN15_6/P15_6 HP_N_DET DSP_PON O I Headphone detection
IIO0_5/RXD6/SCL6/STXD6/AN15_5/
157 EX1_N_CS AC O O Expansion IO 1 chip select
P15_5
IIO0_4/TXD6/SDA6/SRXD6/AN15_4/
158 EX1_N_RST AC O O Expansion IO 1 reset
P15_4
IIO0_3/N_RTS7/N_CTS7/AN15_3/
159 DSP1_N_INT DSP_PON O I Interrupt from DSP1 (for DAU_N_INT distinction)
P15_3
160 IIO0_2/RXD7/AN15_2/P15_2 DSP_MISO DSP_PON I I DSP/DIR reception data
161 IIO0_1/CLK7/AN15_1/P15_1 DSP_SCK DSP_PON O O DSP/DIR communication clock
162 VSS VSS ---
163 IIO0_0/TXD7/AN15_0/P15_0 DSP_MOSI DSP_PON O O DSP/DIR transmission data
164 VCC VCC ---
165 KI3/AN_7/P10_7 +3.3S_PON +3.3S_PON O O +3.3S power supply
166 KI2/AN_6/P10_6 AD2_COM +3.3S_PON O I AD selector 2 COM input
167 KI1/AN_5/P10_5 AD1_COM +3.3S_PON O I AD selector 1 COM input
168 KI0/AN_4/P10_4 HRX2_MT HDMI_PON O I Mute from HDMI RX2 (for HAU_INT distinction)
169 AN_3/P10_3 KY_AD3 AC O I Key 3
172 AVSS AVSS ---
TUN_N_RST PRY O O Tuner reset
173 AN_0/P10_0
HDR_N_RST PRY O O HD radio reset
174 VREF VREF ---
175 AVCC AVCC ---
TUN_SCL PRY O O Tuner I2C clock
176 STXD4/SCL4/RXD4/ADTRG/P9_7
HDR_MISO PRY O I HD radio reception data
Key detection for A/D port

Key input (A/D) pull-up resistance 10 k-ohms
0 + 0.82 k + 0.82 k + 1.0 k + 1.5 k + 1.5 k + 1.8 k + 2.7 k

Detected voltage value 0 0.125 0.358 0.577 0.828 1.078 1.299 1.535
at 171 pin 0.125 V 0.358 V 0.577 V 0.828 V 1.078 V 1.299 V 1.535 V 1.777 V
A/D value
09 10 27 28 44 45 63 64 83 84 100 101 118 119 137
(3.3 V=255)
SCENE SCENE SCENE SCENE ZONE 2 ZONE 3 MAIN ZONE

KEY1
4 3 2 1 ON/OFF ON/OFF
0 + 0.82 k + 0.82 k + 1.0 k + 1.5 k + 1.5 k + 1.8 k + 2.7 k + 3.3 k + 4.7 k + 6.8 k + 12.0 k + 22.0 k
Detected voltage value 0 0.125 0.358 0.577 0.828 1.078 1.299 1.535 1.777 2.010 2.241 2.476 2.709
at 170 pin 0.125 V 0.358 V 0.577 V 0.828 V 1.078 V 1.299 V 1.535 V 1.777 V 2.010 V 2.241 V 2.476 V 2.709 V 2.940 V
A/D value
09 10 27 28 44 45 63 64-83 84 100 101 118 119 137 138 155 156 173 174 191 192 209 210 227
(3.3 V=255)
TONE/ PROGRAM PROGRAM

KEY2 STRAIGHT OPTION ON SCREEN ENTER DISPLAY RETURN
BALANCE
0 + 0.82 k + 0.82 k + 1.0 k + 1.5 k + 1.5 k + 1.8 k + 2.7 k + 3.3 k + 4.7 k

Detected voltage value 0 0.125 0.358 0.577 0.828 1.078 1.299 1.535 1.777 2.010
at 169 pin 0.125 V 0.358 V 0.577 V 0.828 V 1.078 V 1.299 V 1.535 V 1.777 V 2.010 V 2.241 V
A/D value
09 10 27 28 44 45 63 64 83 84 100 101 118 119 137 138 155 156 173
(3.3 V=255)
PRESET PRESET ZONE TUNING/CH TUNING/CH PURE

KEY3 MEMORY INFO FM AM
CONTROL DIRECT
Destination detection for AD port

Pull-up resistance 10 k-ohms
A/D value
0 12 13 39 40 67 68 92 93 115 116 140 141 169 199 221 222 244
(3.3 V=255)
Destination J U C R, S T K A B, G, F L
103
RX-A3030/RX-V3075
Microprocessor extended port

RX-A3030/RX-V3075
IC70, 71: TC74VHC273FT (EL,K) (DIGITAL (1) P.C.B.)

Octal D-type flip-flop with clear
CLR 1 20 VCC
Q1 2 19 Q8 D1 D2 D3 D4 D5 D6 D7 D8
1 3 4 7 8 13 14 17 18
D1 3 18 D8 CLR
D R D R D R D R D R D R D R D R
D2 4 17 D7
Q2 5 16 Q7
Q3 6 15 Q6 CK Q CK Q CK Q CK Q CK Q CK Q CK Q CK Q
11
CK
D3 7 14 D6
D4 8 13 D5
2 5 6 9 12 15 16 19
Q4 9 12 Q5
Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8
GND 10 11 CK
Inputs Output
Function
CLR D CK Q
L X X L Clear
H L L
H H H
H X Qn No Change
IC70
I/O
Pin R32C external
Function Name Related Power Supply Detail of Function
No. bus data
OFF ON
2 D[8] HDMI_PON HDMI_PON O O HDMI power supply (Necessary for DSP, A-VIDEO drive)
5 D[9] HRTX_N_RST HDMI_PON O O HDMI receiver/transmitter reset
6 D[10] MHLVB_PON HDMI_PON O O MHL VBUS power supply control
H: feeding permission, L: feeding prohibition
9 D[11] FLD_PON FLD_PON O O FL driver +3.3V power supply control
12 D[12] FLD_N_RST FLD_PON O O FLD reset
15 D[13] HTX_AUSEL HDMI_PON O O HDMI transmitter sound select
16 D[14] HAU_N_OE HDMI_PON O O HDMI to DIR sound output enable
19 D[15] STBY_LED AC O O Standby LED control
IC71
I/O
Pin R32C external
No. bus data
OFF ON
2 D[0] HSW_N_RST HDMI_PON O O HDMI switcher reset (L period: more than 5ms)
5 D[1] VDEC_N_RST VID_PON O O Video decoder reset
6 D[2] WIFI_PON WIFI_PON O O WiFi adaptor power supply control
9 D[3] HRX_VSEL HDMI_PON O O Video decoder to scaler line enable
12 D[4] FHDMI_N_RST HDMI_PON O O Front HDMI reset
15 D[5] VID_PON VID_PON O O Video power supply
16 D[6] +3.3D_PON +3.3D_PON O O OR of HDMI_PON, DSP_PON, NET_USB_PON
19 D[7] PRY PRY O O Power relay
104
RX-A3030/RX-V3075
RX-A3030/RX-V3075
IC72, 73: TC74VHC273FT (EL,K) (DIGITAL (1) P.C.B.)
Octal D-type flip-flop with clear
CLR 1 20 VCC
Q1 2 19 Q8 D1 D2 D3 D4 D5 D6 D7 D8
1 3 4 7 8 13 14 17 18
D1 3 18 D8 CLR
D R D R D R D R D R D R D R D R
D2 4 17 D7
Q2 5 16 Q7
Q3 6 15 Q6 CK Q CK Q CK Q CK Q CK Q CK Q CK Q CK Q
11
CK
D3 7 14 D6
D4 8 13 D5
2 5 6 9 12 15 16 19
Q4 9 12 Q5
Q1 Q2 Q3 Q4 Q5 Q6 Q7 Q8
GND 10 11 CK
Inputs Output
Function
CLR D CK Q
L X X L Clear
H L L
H H H
H X Qn No Change
IC72
I/O
Pin R32C external
No. bus data
OFF ON
2 D[8] MONO_Z2 PRY O O ZONE2 stereo/mono output switch
5 D[9] MONO_Z3 PRY O O ZONE3 stereo/mono output switch
6 D[10] EX2_N_RST AC O O Reset of expansion IO2
9 D[11] EX2_N_CS AC O O Chip select of expansion IO2
12 D[12] --- AC O O No used
15 D[13] NDAC_I2S DSP_PON O O NET DAC I2S input signal ON/OFF control
IC73
I/O
Pin R32C external
No. bus data
OFF ON
2 D[0] FPGA_N_CFG2 HDMI_PON O O FPGA nCONF2
5 D[1] DVI2C_ON VID_PON O O D-VIDEO I2C control (following VID_PON)
6 D[2] FLP_PON FLD_PON O O FL driver VH and filament power supply control
9 D[3] DAC1_RST DAC_PON O O DAC1 reset (F/C/SR/SRB/SW)
12 D[4] DAC2_RST DAC_PON O O DAC2 reset (FP/RP/SW)
15 D[5] PLL_ON DSP_PON O O Ultra low jitter PLL (CS2300) control
16 D[6] DSP2_N_RST DSP_PON O O Reset of DSP2
19 D[7] DAC_PON PRY O O ESS DAC power supply control
105
RX-A3030/RX-V3075
RX-A3030/RX-V3075
IC76, 77: SN74LV4051APWR (DIGITAL (1) P.C.B.)

8-channel analog multiplexers/demultiplexers
Y4 1 16 VCC
Y6 2 15 Y2
COM 3 14 3
Y1 COM
Y7 4 13 Y0
Y5 5 12 13
Y3 Y0
INH 6 11 A
GND 7 10 B 14
11 Y1
GND 8 9 C A
15
Y2
12
10 Y3
B
INPUTS ON
1
INH C B A CHANNEL Y4
L L L L Y0
5
L L L H Y1 9 Y5
C
L L H L Y2
L L H H Y3 2
Y6
L H L L Y4
L H L H Y5 4
6 Y7
L H H L Y6 INH
L H H H Y7
H X X X None
IC76
I/O
Pin
No.
OFF ON
1 Y4 THM2 +3.3S_PON I I Temperature detection 2
5 Y5 DEST +3.3S_PON I I Destination distinction
12 Y3 MODEL +3.3S_PON I I Model distinction
13 Y0 MHL_VBUS_PRT +3.3S_PON I I MHL overcurrent detection (spare)
14 Y1 USB_VBUS_PRT +3.3S_PON I I Front USB overcurrent detection
15 Y2 (Spare) +3.3S_PON I I ---
IC77
I/O
Pin
No.
OFF ON
1 Y4 PS2_PRT +3.3S_PON I I Power supply protection 2
2 Y6 PS1_PRT +3.3S_PON I I Power supply protection 1
4 Y7 AMP_OLV PRY I I Amplifier output level detection
5 Y5 DC_PRT PRY I I DC protection
13 Y0 PS3_PRT AC I I Power supply protection 3
14 Y1 L3_DET VID_PON I I D terminal L3 detection
15 Y2 MODE +3.3S_PON I I Special mode distinction
106
RX-A3030/RX-V3075
RX-A3030/RX-V3075
IC101, 306: R5F213G1DN400SP (MAIN (3) P.C.B., VIDEO (1) P.C.B.)
I/O-expander for microprocessor
4 8 4 3 1
I/O ports Port P0 Port P1 Port P3 Port P4
Peripheral functions
UART or System clock
clock synchronous serial I/O generation circuit
Timers (8 bits x 2)
XIN-XOUT
High-speed on-chip oscillator P0_2/AN5(/TRCIOA/TRCTRG) 1 24 P0_6/AN1(/TRCIOD)
Timer RA (8 bits x 1) Low-speed on-chip oscillator
Timer RB (8 bits x 1) XCIN-XCOUT P0_1/AN6(/TRCIOA/TRCTRG) 2 23 P0_7/AN0(/TRCIOC)
Timer RC (16 bits x 1)
Timer RE (8 bits x 1) P4_2/VREF 3 22 P1_0/AN8/KI0(/TRCIOD)
Low-speed on-chip oscillator
for watchdog timer MODE 4 21 P1_1/AN9/KI1(/TRCIOA/TRCTRG)
RESET 5 20 P1_2/AN10/Kl2(/TRCIOB)
Voltage detection circuit
Watchdog timer
P4_7/XOUT(/XCOUT) 6 19 P1_3/AN11//Kl3/TRBO(/TRCIOC)
(14 bits)
Comparator B VSS/AVSS 7 18 P1_4(/TXD0/TRCCLK)
A/D converter
P4_6/XIN(/XCIN) 8 17 P1_5(/INT1/RXD0/TRAIO)
(10 bits x 8 channels)
VCC/AVCC 9 16 P1_6//IVREF1(/CLK0)
P3_7/TRAO(/RXD2/SCL2/TXD2/SDA2) 10 15 P1_7/IVCMP1/INT1(/TRAIO)
R8C microprocessor core Memory
P3_5(/CLK2/TRCIOD) 11 14 P4_5/ADTRG/INT0(/RXD2/SCL2)
R0H R0L SB ROM(1)
R1H R1L
P3_4/IVREF3 12 13 P3_3/IVCMP3/INT3
USP (/RXD2/SCL2/TXD2/SDA2/TRCIOC) (/CTS2/RTS2/TRCCLK)
R2
R3 ISP
INTB RAM(2)
A0
PC
A1
FB FLG
Multiplier
NOTES:
1. ROM size varies with MCU type.
IC101 (Expansion IO2)

I/O
Pin
No.
OFF ON
8 P17 --- --- O --- No used
9 P16 --- --- O --- No used
10 P15 --- --- O --- No used
11 P14 --- --- O --- No used
12 P13 AMP_POFF AMP_OFF O O Spare (Power amplifier off for preamp mode)
13 P12 PRY2 PRY O O Power relay
(Z71, spare at the time of the toroidal correspondence)
14 P11 --- --- O --- No used
15 P10 PA_B_RY1 PRY O O Power amplifier B power supply control 1
17 P07 --- PRY O --- No used
18 P06 SPRY_F_RP_CTRL PRY O O SP relay front -> SP2
19 P05 SPRY_ZRP_CTRL PRY O O SP relay SB -> SP2
20 P04 SPRY_ZFP_CTRL PRY O O SP relay FP -> SP1
21 P03 SPRY_SB_CTRL PRY O O SP relay surround back
22 P02 SPRY_SR_CTRL PRY O O SP relay surround
23 P01 SPRY_C_CTRL PRY O O SP relay center
24 P00 SPRY_F_CTRL PRY O O SP relay front
IC306 (Expansion IO1)

I/O
Pin
No.
OFF ON
8 P17 --- AC O O No used
11 P14 DC_TRG2 PRY O O Control out 2
13 P12 DC_TRG1 PRY O O Control out 1
14 P11 VO_SEL2 VID_PON O O MON output select of Y/C
15 P10 VO_SEL1 VID_PON O O MON output select of Y/C
18 P06 VID_SEL1 VID_PON O O Input select of Y/C
21 P03 V_N_FMUTE VID_PON O O Video full mute
22 P02 VZ_SEL3 VID_PON O O ZONE2 select of Y/C
107
RX-A3030/RX-V3075
RX-A3030/RX-V3075
IC61, 62: Sii9136CTU-3 (DIGITAL (1) P.C.B.)

HDMI transmitter
CEC
40 CEC
Interface
CSDA 44 I2C Slave DDC Master 41 DSDA
CSCK 45 Interface Configuration
I2C Interface 42 DSCL
Logic and
CI2CA 43 Registers
46 INT
RESET 47 Hot Plug Detect Hot-Plug
76 HPD
Receiver Sense Detector
and Interrupt Logic 26,39,49,77
GPIO GPIO[3:0]
IDCK 22
2-4,6-11,13-15,17-20,
D[35:0] 78-87,89,90,92-99 Video Data Input
HSYNC 24 and
23 Conversion 52 EXT_SWING
VSYNC
DE 25 54,55
HDCP HDCP TXC 0
ROM TMDS 57,58
SPDIF_IN 29 Encryption TX0 0
Transmitter 59,60
MCLK 36 Engine TX1 0
62,63
SCK 35 Audio Data XOR TX2 0
WS 34 Capture Framer Mask
SD[3:0] 30-33
27,28
SL[3],DR[3]
I/O
Pin
No.
OFF ON
26 GPIO0 NC HDMI_PON --- O Unconnected: output low setting
77 GPIO1 NC HDMI_PON --- O Unconnected: output low setting
39 GPIO2 CEC_EN HDMI_PON --- O CEC function of HDMI TX1 / effective/invalidity (spare)
49 GPIO3 5HT*_PON HDMI_PON --- O HDMI out * 5VPWR output control
108
RX-A3030/RX-V3075
PIN CONNECTION DIAGRAMS

ICs ICs
A3V56S30FTP-G6 ADV7172KSTZ ADV7619KSVZ 74LVC2G17GW BA15218F D80YK113CPTP400
ADV7630KSVZ TC74HC4051AFEL TC74LCX32FT TC74LCX245FT TC74VHCU04FT TC74VHC273FT (EL,K) TC74VHC157FT
54 28 48 37 BD7542F-E2 TC74LCX125FT TC74VHC08FT
96 65 132 89 TC74HC4052AF
1 36 97 64 4 133 88
6
3 8 4
10
1 1 8
8 7 20 10 16
1 27 16 14 7 20 14
ADV7181CBSTZ BD9328FJ CS230009-CZZR 1 1 1 1
12 25 1 1
48 33 128 33 BD9329AEFJ-E2
49 32 13 24 1 32
TC7WHU04FU TC7WH32FK (TE85L, F) TC7SET08FU TRS3221ECPWR W25Q80BVSSIG
AK5386VT 10 176 45 TC7WH08FU (TE12L,F) TC7SZ04FU
8 4 5 TC7SH08FU
64 17 16 8 1 44
1 1 TC7SH86FU
1 16 1
TC7SZ125FU
DM860A-AQE EN29LV640AB-90TIP EP4CE15F23C6N 22 1 ES9006S 8
A 8 8 4 4
4 8 4
18 1 MX29LV640EBTI-70 ES9016S 5 16
A 1 1 3 1
36 25 1
1
1 48 37 24
V 18
AB 22
A 1
24 48 13
25 A 1
V
AB 1 12
Diodes
FHP3350IM14X KIA7812API KIA7912PI L6566BTR LAN8700C-AEZG-TR LM19CIZ/LF
1SS355VMTE-17 BAV103 D1NL20U-5083 D2SBA60-7001 D4SBS6-7101 4A 60V DA2J10100L ESD7004MUTAG
27 19 1SS400TE61 D5SBA60 5A 600V
28 27
D15XBN20
28 18 6
36 19 Anode
Anode Anode 10
14
1 18 Anode 5
28
14 7 1
9 10 36 10 +VS 1,2,4,5 : I/O
IN GND VOUT 3,8 : GND
1 Cathode Cathode Cathode AC Cathode
1 OUT OUT GND AC AC 6,7,9,10 : NC
COM IN 1 9 + + AC
M12L64164A-5TG M95512-RDW6TP/K MFI337S3959 MX29GL256FLT2I-90Q NCP380HMUAJAATBG NE5532DR P6KE200ARL RB215T-60 RB051L-40 RB501V-40 RF101L2STE25 STTH110A UDZS6.2B 6.2V
RB521S-30 UDZS13B 13V
UDZV4.3B
1 56 Anode Anode Anode UDZV5.1B
8 4 Anode
54 28 Anode Anode UDZV5.6B
1 UDZV7.5B
4 1 3
5
6
UDZV8.2B
8 NJM2068MD-TE2 Cathode UDZV15B
Cathode Cathode Cathode Cathode
8 1
2
Cathode UDZV22B
4 3 3
4
1 1 1 6 4
28 29 8 4
1 27
1
NJM4565M (TE1) NJM431U NJM2388F33 NJW1327FU1 NT5SV8M16HS-6K PCM5101PWR

80 51
81 50 54 28
Transistors
2N5401C-AT/P 2N5401S-RTK 2N5551C-AT 2N7002KA-RTK/P 2SA1208S/T-AE 2SA1576A 2SC1815 Y 2SC4488 2SB1257 2SC2910S/T-AE
2SA1576UBTLR 2SD2014
1 10
8 4 2
3
1 1 20
1: REFERENCE 1. VIN
4 100 31
2: ANODE 2. VOUT
1
3. GND 1 27 G
3: CATHODE C
4. ON/OFF CONTROL 1 30 C
E D E
PCM9211PTR R2A15220FP R5F213G1DN400SP#W4 R1163N501B-TR-FE R1171S501B-E2-FE R1172H121D-T1-F S B B
E B E E C
R1172H331D-T1-F C B CB E E
R1172N301D-TR-F B CE C B C
36 25 80 51 B CE
R3112N421A-TR-F R1173H001D-T1-FE B
37 24
81 50 2SC2712-Y (TE85R, F) 2SC3906K 2SC4081UBTLR 2SC5964-TD-E 2SCR513P 2SD2704 K 2SK208-Y DTA044EUBTL DTC114EKA HN4B01JE
1 2SC3326-A (TE85R, F) DTC014EUBTL DTC144EKA
12 4 2SC3326-B (TE85R, F) DTC044EUBTL 4
5 6 3
100 31
24 3 3 5 2SC4081 T106 3 5
3 3
48 13 1 1 4 2SC4213-A/B TE85L
C 1 1
1 30 1 C C G 2
1 12 C 1. BASE 1 (B1)
E 1 2
E E D 2. EMITTER (E)
E B 1: IN 1: GND 3. BASE 2 (B2)
B
R5F6416MADFE RP130Q121D-TR-F SiI9136CTU-3 SII9587CNUC-3 SN74LV4051APWR B B C C
E B S 2: GND 2: IN 4. COLLECTOR 2 (C2)
B E 3: OUT
RP130Q181D-TR-F 3: OUT 5. COLLECTOR 1 (G2)
132 89 75 51
RP130Q251D-TR-FE STD05P STD05N
133 88 HN4C06J KRA304-RTK/P KTA1046-Y-U/PFY KTA1504S MCH6336-TL-E RAL035P01 STF9NK90Z PA672T-T1-A
RP130Q331D-TR-F 76 50 KTA1659A-U/PF
66 45 KRC404-RTK/P KTC3875S
RP130Q501D-TR-F 4 KTC4370A-Y-U/PF 4 4 4
67 66 67 44
5 6 6 6
3 3
88 3 3
45
3 1 1 1 1
OUT C
4 1 44 8 1. Drain
2 2. Drain 1. DRAIN 1. Source 1 (S1)
16 1. BASE 1 (B1) E
2. EMITTER (E) COMMON 3. Gate
2. DRAIN 2. Gate 1 (G1)
1 88 23 3. GATE 3. Drain 2 (D2)
22 23 3. BASE 2 (B2) B 4. Source
100 26 1 IN 4. SOURCE GD 1 1 4. Source 2 (S2)
1 22 4. COLLECTOR 2 (C2) 23 23
176 45 5. COLLECTOR 1 (G2) 5. Drain 5. DRAIN S 45 45 5. Gate 2 (G2)
6. Drain 6. DRAIN 6. Drain 1 (D1)
1 44 BC
1 25 E
109
A B C D E F G H I J
RX-A3030/RX-V3075
1 BLOCK DIAGRAMS
AUDIO Section Block Diagram
AV1 (Coax)
FUNCTION (3) AV2 (Coax)
AV3 (Opt)
DA_BCK
DA_WCK IC942
Sur.Back IC734 DA_SBL (to #1)
DA_SBR (to #1)
See page 157 AV4 (Opt)
AV-OUT/ZONE4 (Opt)
HDMI Rx
IC911 Sur.Back
Front
DAC1 Front IC731 DA_FL (to #2)
DA_FR (to #2)
DSP1
SCHEMATIC DIAGRAM AUDIO1 (Opt)
AUDIO2 (Coax)
IC900 D80YK113 Surround
C/SW1 ES9016
Surround IC733 DA_SL (to #1)
DA_SR (to #1)
DIR/ADC
C/SW1 IC732 DA_CEN (to #1)
2 See page 158 DA_SW1 (to #2)
OPERATION V-AUX (Opt) HDMI Tx
SCHEMATIC DIAGRAM PCM9211
IC735
AD_MZ
(from #1)
LAN
IC951 NE5532DR
DA_BCK SW2 DA_SW2 (to #2)
NETWORK IC943
IC920 Sur.Back DA_WCK
USB microprocessor Front DAC2 FrontPre IC736 DA_FPL (to #2)
IC903 Zone2 IC944 DSP2 Surround DA_FPR (to #2)
HDMI Tx ADC D80YK113 C/SW1
Zone2
AK5386VT SW2 ES9006
DIR/ADC
IC937
DAC DA_NET AD_Z2 PCM9211 DAC DA_Z2
FrontPre
RearPre
RearPre IC737 DA_RPL (to #2)
DA_RPR (to #2)
FUNCTION (2)
See page 156
PCM5101 (to #1/2) (from #2) PCM5101 (to #2)
0dBFs=2.1Vrms
DIGITAL See page 145154
SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAM See page 161
AMPPOWER
AD_MZ (to MZ-ADC) SCHEMATIC DIAGRAM
Max:2.1Vrms/typ:0.2Vrms -95dB0dB
ADC(OUT) AD_MZ2 (to #2 SBCIN) Multi1 0dB42dB
Zone2(ANLG_Z2,DA_Z2,DA_F)
Multi IN(F) SUB1(OUT) ANLG_Z2 (to #2 IN1) Multi2 Front Zone2 (Pre/FpAmpSp1) BIAMP
3 IN1
SUB2(OUT) ANLG_Z3 (to #2 IN2)
Fp(DA_FP)
Bypass
Tone
50k Control Zone2/Zone3 ExtraSP
Bypass Zone2 (FrAmpSP2) Front Pres. ZONE2/ZONE3/
AUDIO4 IN2 Mute F. PRESENCE/
MainSel: for MainZone MT_EX1_MI 29.03dB SPRY_ZFP BI-AMP
Sub1Sel: for Zone2 Front (SP/XLR)
AUDIO3 IN3 Sub2Sel: for Zone3 Zone2/Zone3
Rear Pres.
Mute FRONT L/R
AUDIO2 IN4 -95dB0dB MT_F_MI 29.03dB SPRY_F
DA_CE Multi1 0dB42dB
Multi IN(C) Multi2 Center Center (Pre/SP/XLR) Center (SP/XLR)
AUDIO1 IN5 INA/REC1 AV-OUT 50k Mute CENTER
INB/REC2 MT_MZ 29.03dB SPRY_C
REC3
AV4 IN6 IN10/REC4
SPEAKERS
IN11/REC5 ExtraSP2
-95dB0dB ZONE2/ZONE3/
AV3 IN7 Multi1 0dB42dB SPRY_F_RP R. PRESENCE/
Multi2 Subwoofer
50k
AV2 IN8 SPRY_ZRP
Surround
4 OPERATION AV1 IN9
(SP/XLR)
Mute SURROUND
-95dBdB MT_MZ 29.03dB SPRY_SR
See page 158 IC703 DA_SL/SR Multi1 0dB42dB S.Back
PHONO INB/REC2 Multi IN(S) Multi2 Surround Surround (Pre) (SP/XLR)
SCHEMATIC DIAGRAM PhonoEQ. 50k Mute SURROUND BACK
NJM2068MD Surround (SP/XLR) MT_SB_MI SPRY_SB
29.03dB typ:28.3Vrms(Vol:+16.5dB)
DA_NEV IN10/REC4
See page 159, 160

V-AUX IN11/REC5 -95dB0dB
Zone2 S.Back[RP]
SP[SP2] AMP
DA_SBL/SBR Multi1 0dB42dB SP2
SCHEMATIC DIAGRAM
Multi IN(SB) Multi2 Surr.Back Surr.Back (Pre)
YPAO MIC IN12 50k IC705 typ:1Vrms(Vol:+16.5dB)
IC701 Surr.Back (SP/XLR) Mute ZONE2
R2A15220FP *2 PRE_Z3 "Sub2" Zone2/Zone3
NJM4565M MT_Z2
AM/FM Tuner IN13 #1(1/2) SCIN 0dB
SBCIN typ:1Vrms(Vol:+16.5dB)
VIDEO IN14
"Sub1" IC701
R2A15220FP
Mute
MT_MZ
CENTER
See page 164, 165 AD_Z2

#1(1/2)
typ:1Vrms(Vol:+16.5dB)
Zone2 (FpAmpSP1)
SCHEMATIC DIAGRAM MUTE (to Z2-ADC) Mute SURROUND
5 Zone3 (SbAmpSP2)
MT_MZ
-95dB0dB IC707 typ:1Vrms(Vol:+16.5dB)

Zone2 HDMI
ADC(OUT)
(ANLG_Z2,
Multi1 0dB42dB RP (Pre) Mute SURROUND BACK
ANLG_Z2 IN1 Multi2
Tone
Front Zone3 (Pre/SbAmpSP2) 0dB MT_SB_PO(*b)
(from #1) Zone2Mono Bypass 50k Control NE5532DR
Bypass RP (FrAmpSP2/XLR) J7019/7020
ANLG_Z3 IN2 SUB1(OUT) Zone3 (FrAmpSP2)
Zone3(ANLG_Z3,DA_F)
(from #1) SUB2(OUT) Zone3Mono
Rp(DA_RP) typ:1Vrms(Vol:+16.5dB)
IC706
IN3 MainSel: for Zone2(ADC) Mute ZONE3 PRE OUT
Sub1Sel: for Zone2 0dB MT_Z3
Sub2Sel: for Zone3 NJM4565M
DA_NET IN4 -95dB0dB
DA_SW2 Multi1 0dB42dB IC708
Multi2 Center Subwoofer2 (Pre) typ:1Vrms(Vol:+16.5dB)
DA_Z2 IN5 INA/REC1 50k Mute SUBWOOFER2
INB/REC2 4.62dB MT_MZ
REC3 NE5532DR
DA_FL/FR IN6 IN10/REC4
IN11/REC5
-95dB0dB
DA_FPL/FPR IN7 IC704 DA_SW Multi1 0dB42dB IC708
6 Multi IN(SW1) Multi2 Subwoofer Subwoofer1 (Pre) typ:1Vrms(Vol:+16.5dB)
50k Mute SUBWOOFER1
NJM4565M
DA_RPL/RPR IN8 4.62dB MT_MZ
NE5532DR
IN9
-95dB0dB
Multi1 0dB42dB IC711
INB/REC2 Multi2 Surround Front (Pre/HP) typ:1Vrms(Vol:+16.5dB)
50k Mute FRONT
Front (SP/XLR) 0dB MT_MZ
IN10/REC4 NE5532DR
Zone3
IN11/REC5 -95dB0dB
DA_FPL/FPR Multi1 0dB42dB
Multi2 Surr.Back IC709 typ:0.6Vrms @8
IN12 PRE_Z2 50k (Vol:+16.5dB)
IC702 BIAMP/Zone2/Zone3 (FbAmpSP1) Mute
PHONES
R2A15220FP "Sub2" (FpAmpSP1/XLR) MT_HP 100
IN13 #2(2/2) DA_FL/FR SCIN 17.78dB
AD_MZ (from #1) SBCIN BA15218F
7 "Sub1" IC702
IN14 R2A15220FP
See page 155 See page 158
#2(2/2) FUNCTION (1) OPERATION
MUTE SCHEMATIC DIAGRAM SCHEMATIC DIAGRAM
110
A B C D E F G H I J
RX-A3030/RX-V3075
DIGITAL P.C.B. Section Block Diagram
HDMI (Front)
See page 146 See page 146
DIGITAL (2) RS-232C DIGITAL (3)
SCHEMATIC DIAGRAM SCHEMATIC DIAGRAM
IC32
HDMI Equalizer Front USB
HDMI IN SII9587CNUC-3
HDMI OUT IC39
2 232C
TRS3221ECPWR
OUT2 OUT1 NETWORK
IN7 IN6 IN5 IN4 IN3 IN2 IN1 ZONE2/4
CEC
RS232C
DV_SCL/SDA
IC62 IC61 TX/RX
B IC2 C B IC1 C
HDMI HDMI
A HDMI Switcher D A HDMI Switcher D Transmitter Transmitter
HDMI_SCL/SDA ADV7630KSVZ HDMI_SCL/SDA ADV7630KSVZ HDMI_SCL/SDA
Sil9136CTU-3 Sil9136CTU-3
HDMI_SCL/SDA
HSW2_27MHz TXB TXA HSW1_27MHz TXB TXA
IC955
IC66 Ethernet PHY USB_DP/DM
3 ARC Buffer LAN8700C-AEZG-TR
TC7WHU04FU
Main HDMI Audio
RT_SD0-3 RT_SD1-3
RXB RXA RMII 50MHz

HDMI_SCL/SDA IC3 HDMI_SCL/SDA
RXB RXA Zone HDMI Audio RT_SPDIF
IC4 RTZ_SD0-3
SZ_SPDIF
SZ_SD0-3
HDMI Receiver HDMI Receiver XL951
RTZ_SPDIF 24MHz
ADV7619KSVZ ADV7619KSVZ I2C_SCL/SDA K3 J3
115 116 IC53
115 116
XL1 SDRAM 128Mbit IC956
XL2
28.63636MHz 28.63636MHz NT5SV8M16HS-6K iPod
IC951
FPGA_27MHz 16bit Authentication IC
27MHz
HSW1_27MHz MFI337S3959 NETWORK
48bit 36bit
HSW2_27MHz
OUT1 microprocessor
FPGA_27MHz Zone IN
36bit
FPGA2_27MHz
48bit
OUT0 SMSC
IC50
4 IN0
FPGA
DM860A-AQE
16bit 16bit
IN0 20bit EP4CE15F23C6N Main/Zone HDMI
IC23-25 OUT1 IN1 Audio Repeat IC952 IC953
IC40 SDRAM NOR Flash
NCPU SPI
Buffer
Net/USB I2S
TC74LCX245FT FPGA 256Mbit 256Mbit
ADCVBS EP4CE15F23C6N A3V56S30FTP-G6 MX29GL256FLT2I
AIN1 SCLR_27MHz x2 DIR2_SD0
IC21 VENC OUT
ADSY
AIN2 20bit
IC901,902 IC954
HDMI Decoder 16bit 16bit 8bit
Analog Video IN ADSC
AIN3 16bit TC74VHC157FT CB943
IC41 IC42 IC937
ADPb
AIN4
ADV7181CBSTZ SDRAM SDRAM Zone Audio UP NET_L / R
DAC
ADPr
AIN5 DV_SCL/SDA
128Mbit 128Mbit
FPGA_N_CS Analog Audio Output
ADY
PCM5101PWR
AIN6 Main HDMI Z2_SPDIF
MAIN OUT
21 22 IC75 FPGA SPI
RT_SD1-3
ZONE I2S
16bit
IC903 IC938 ZONE_L / R
XL20
Flash ROM RT_SPDIF I2S SD0
DSP SPI Analog Audio Output
no use DIR2 DAC
28.63636MHz 64Mbit SPDIF from DIR1 PCM5101PWR
EN29LV640AB-90T IC64 PCM9211PTR
DAY SPDIF from RX2
DAC A FLASH_N_CS
RT_SD0 TC74VHC157FT AUP_SD0 MPIO_C
DAPb IC20 IC944
5 Analog Video OUT DAPr
DAC B
DAC C HDMI Encoder
IC70,71 16bit
MPO1
ADC
ADC
Main_AD_L / R
Analog Audio Input
DACVBS DFF1 Buffer IC65 AUP_SD0
DAC D ADV7172 AK5386
DASY DV_SCL/SDA TC74VHC273FT TC74LCX245FT Main AudioUP 39 40 Zone2_AD_L / R
DAC E
RTZ_SD0-3 XL901
Analog Audio Input
DASC
DAC F DFF1_N_CS 24.576MHz
XMCKO
RTZ_SPDIF
IC72,73
16bit NCPU SPI
DFF2
TC74VHC273FT HDMI_ARC
(HDMI SPDIF) HDIG_DSD0A
RS232C
DFF2_N_CS
MPIO_B HDMI RX1_SPDIF

EBIU SPI6 SPI9
UART1 RX1 I2S (HPSD0)
MPIO_C HDMI_ARC CB924
DV_SCL/SDA UART2 UART8
IC900 AV1_D
HDMI_SCL/SDA I2C3
IC79 HPSD1SD3 DSP SPI DIR1 AV2_D
Tuner/HD Radio I2C4/UART4
DIR I2S AV3_D SPDIF Input
Microprocessor McASP1 PCM9211PTR
6 FLD/EXIO
HEQ_SCL/SDA I2C5
SPI10 R32C/116A HDIG_DSD0A
(HDMI DSD)
McASP1
MAIN OUT AV4_D
R5F6416MADFE IC911 McASP0

DSP SPI
ADC
IC76 SPI0 SPI1 DSP1
IC78 Analog Mux 166 D80YK113CPTP400
AN6 16bit
EEPROM SN74LV4051APWR EMIFB DSP I2S SD0-7
McASP1
RAM:96K Byte IC942 CB944,945
512Kbit DAC1_SCL/SDA
M95512-RDW6TP/K IC77 ROM:1M Byte DAC
Analog Mux 167 SPI0
AN5 IC920 ES9006S
SN74LV4051APWR AN4
Clock:50MHz 16bit DSP SPI SPI1
Main Zone I2S
DSP2
KY_AD3
169
AN3
Analog Audio Output
170 IC913 IC910 16bit D80YK113CPTP400
Front Panel Key KY_AD2 AN2 143 145 EMIFB
171 SDRAM Serial Flash McASP0 DSP I2S SD0-6
KY_AD1 AN1 XL910
DAC2_SCL/SDA IC943
64Mbit 8Mbit 20MHz SPI0 DAC
22 24 M12L64164A-5TG2 W25Q80BVSSIG
ES9006S
XL70
8MHz
CERALOCK IC922 IC921
SDRAM Serial Flash
7 143 145
64Mbit 8Mbit See page 145154
XL911
20MHz DIGITAL (1)
SCHEMATIC DIAGRAM
111
A B C D E F G H I J
RX-A3030/RX-V3075
VIDEO Section Block Diagram
IC309
AUX_C
VID_ / VZ_ SEL1(A) SEL2(B) SEL3(C) See page 164, 165
AUX_Luma VIDEO (1) P.C.B. AMPPOWER
V-AUX MUTE L L L SCHEMATIC DIAGRAM
RESET
MODE
VCC
AUX_CVBS AV1 H L L
TX
RX
OPERATION AV2 L H L Test point
See page 158 FHP3350IM14X
for writing
AV3 H H L
SCHEMATIC DIAGRAM MAIN Selector
AV4 L L H
2 IN1_Luma 3.3V
IOXV_MOSI
V-AUX H L H
IN2_Luma IC301
232C_Tx
H H H +18V 7V
+3.3M
IN3_Luma Luma
L3_DET (U model)
IR_IN1
IN4_Luma
D4 VIDEO TC74HC4051AF PS1_PRT D3310
IC331
(J model) AUX_Luma IN_Luma
+3.3HDR +3.3M
Infrared LED
IR_OUT1
1
SIR-505STA47
+3.3HDR NJM2388F33 +7V +3.3M U3301
IN1_Y IN1_C VID_SEL1 VID_SEL1 REM_IR REMOTE
REM_IN2 IR_IN2
IN2_C IC302 VID_SEL2 VID_SEL2 SM3385VMH6 IN/OUT
IN1_Pb D3311
AV1 IN3_C VID_SEL3 HS331 VID_SEL3 Infrared LED 2
C
IN1_Pr SIR-505STA47 IR_OUT2
IN4_C IN_C VID_PON
TC74HC4051AF IC332 VZ_SEL1
IN1_C
AUX_C +3.3V
IN1_Luma +3.3V NJM2388F33 +7V VZ_SEL2
3.3V
VZ_SEL3
3 IN1_CVBS IC306
VO_SEL1
ZONE Selector HS332 I/O Expander
PS1_PRT VO_SEL2
IN1_Luma 3.3V Q3304 R5F213G1DNSP
-3.3V V_N_FMUTE
IN2_Luma -3.3V +3.3V
IN2_Y IC303 KTA1046-Y-U/P
IN3_Luma
IN2_Pb Luma DC_TRG1
IN4_Luma +18V
IN2_Pr TC74HC4051AF DC_TRG2 DC_TRG1 Q3311-Q3318
ZONE_Luma HS333
AUX_Luma
AV2 IN2_C DC_TRG2
12V / 100mA TRIGGER OUT 1/2
IN_Luma IOXV_CLK Driver
IN2_Luma IN1_C VZ_SEL1 3.3V
+12V MAX 100mA
IN_C IC308 IOXV_N_CS
IN2_C VZ_SEL2 VO_SEL1
IN2_CVBS Location Specification
IC304 ZONE_Luma Luma / C IOXV_N_RST
IN3_C VZ_SEL3 VO_SEL2
C Q3311 KTA1504S-Y, GR-R
ZONE_C OUTPUT IOXV_MOSI
to FUNCTION (1)
VIDEO INPUT IN4_C
TC74HC4051AF
ZONE_C
Selector DA_Luma Q3312 KTA1504S-Y, GR-R
(U model)
OUT_Luma
4 AUX_C
TC74HC4052AF
DA_C Q3313 KTC3875S-Y, GR-R
+5T
IN3_Y 3.3V OUT_C TUL
Q3314 KTC3875S-Y, GR-R
IN3_Pb TUR
Q3315 KTA1046-Y-U/P
IN3_Pr IN_Luma IC307 Q3316 KTA1046-Y-U/P
AV3 IN3_C IN1_CVBS MAIN S Video
SVID_DET Detector Q3317 KTC3875S-Y, GR-R
IN3_Luma IN2_CVBS 0/6 1 K-ohms AD_M_CVBS +3.3V
TC74VHCU04FT
HD Radio tuner
(0dB Buffer) Q3318 KTC3875S-Y, GR-R
(U model)
IN3_CVBS +3.3HDR
IN3_CVBS 0/6 1 K-ohms AV_CVBS VID_SCL TUN_N_RST
IN4_CVBS (6dB Buffer)
+3.3V
9 IN / 5 OUT
VID_SDA TUN_N_INT
Selector
AUX_CVBS 6dB 75 ohms MON_CVBS Q3004

(6dB Driver)
FET SW TUN_SCL
OUT_Luma HDMI_SDA
IN4_Y 6dB 75 ohms UPA672T-T1-A
MON_Luma (6dB Driver) +3.3M TUN_SDA
OUT_C HDMI_SCL
IN4_Pb
DA_CVBS 6dB 75 ohms MON_C (6dB Driver)
5 IN4_Pr
AV4 IN4_C IN1_Y 0/6 1 K-ohms AV_C
(6dB Buffer)
IN4_Luma IN2_Y
0/6 1 K-ohms AD_M_C
6 IN / 4 OUT
IN3_Y (0dB Buffer)

Selector
IN4_CVBS
IN4_Y 6dB 75 ohms MON_Y (6dB Driver)
IN_C AD_M_Y TUN_N_RST
6dB 75 ohms AD_M_Y
DA_Y (6dB Driver) AD_M_Pb TUN_N_INT
IN1_Pb 0/6 1 K-ohms AD_M_Pr TUN_SCL Microprocessor
AV_C (6dB Buffer) Video
IN2_Pb AD_M_Luma TUN_SDA
Decoder or
6 IN / 4 OUT
AV_Luma 0/6 1 K-ohms

IN3_Pb (6dB Buffer)
Selector
AD_M_C HDMI_SDA
IN4_Pb 6dB 75 ohms AD_M_CVBS HDMI_SCL AD
AV OUT MON_Pb (6dB Driver)
DA_Pb Selector
AV_CVBS PS1_PRT
6 6dB 75 ohms AD_M_Pb (6dB Driver) VID_PON
IN1_Pr 0/6 1 K-ohms AV_Luma or
(6dB Buffer) FPGA / Video
IN2_Pr SVID_DET
MONITOR OUT/ Processor
6 IN / 4 OUT
0/6 1 K-ohms AD_M_Luma (0dB Buffer) REM_IN2 D-type

IN3_Pr
Selector
ZONE OUT IR_OUT

flip-flop
IN4_Pr 6dB 75 ohms (6dB Driver)
MON_Y MON_Pr
DA_Y L3_DET
IN_Luma
MON_Pb 6dB 75 ohms DA_Pb
DA_Pr AD_M_Pr (6dB Driver)
MONITOR OUT MON_Pr
VID_SCL
DA_Pr
/ZONE OUT Video
MON_C IC305 DA_Luma HDMI
VID_SDA Encoder
MON_Luma CVBS/Component Selector DA_C
3.3V CVBS/Luma/C/CVBS Driver V_N_FMUTE
DA_CVBS
MON_CVBS L3_DET NJW1327FU1
7
DIGITAL See page 145154
SCHEMATIC DIAGRAM
112
A B C D E F G H I J
RX-A3030/RX-V3075
Power Amplifier and Power Supply Sections Block Diagram

Power amplifier
+LB/-LB
+B/-B RY105
FL
29dB +
+LB/-LB - VIDEO P.C.B.

+B/-B FRONT
FR RY105
29dB + L/R
PRIMARY SECONDARY
+LB/-LB -
2 C
+B/-B
RY104
29dB + +5.5V
AC IN T2001 DIGITAL P.C.B.
CENTER Q2001 SUB-transformer
+LB/-LB -
+B/-B Switching Transistor
SL RY107
29dB +
+LB/-LB - IC203
+B/-B SURROUND
SR RY107 Lower Voltage limit IC
+ L/R IC201
29dB Switching Control IC
L6566BTR IC204
- Over Voltage limit IC
RY101
+ SPEAKERS
3 RY102 -
ZONE 2/ZONE 3/ POWER
RY101 R. PRESENCE
+
L/R See page 162
+LB/-LB RY102 - SCHEMATIC DIAGRAM
+B/-B
SBL RY106
29dB +
+LB/-LB -
+B/-B AMPPOWER P.C.B.
SBR RY106 SURROUND BACK
29dB + L/R
+LB/-LB -
+B/-B
FPL RY108
29dB +
4
+LB/-LB -
FPR
+B/-B
RY108
ZONE 2/ZONE 3/
29dB + F. PRESENCE/
BI-AMP
-
L/R
VIDEO P.C.B.
I_PRT
DC_PRT PRIMARY SECONDARY

AMP
AMP_OLV
See page 159, 160
EX_SCK +5.5V
SCHEMATIC DIAGRAM
R5F213G1DN400DP
AC IN T2001
EX_MOSI SUB-transformer
Q2001
5 Switching Transistor
EX2_N_CS
Power +3.3M
EX2_N_RS RY180
+B Transformer
+LB
IC203 MCPU_N_RST
C1822 D1808 Lower Voltage limit IC
IC201
AMP_LMT IC182 Switching Control IC
L6566BTR IC204 DEST
-B
-LB C1823 Over Voltage limit IC
PS1_PRT IC202 ACPWER_DET

+7 RY201 AC Detection IC DIGITAL P.C.B.
Power relay
D1807 PRY
C1826
PS2_PRT
6
-7 C1827
Q1804 POWER2
+5A
+5A
D1810 See page 163
SCHEMATIC DIAGRAM
C1828
+12V Q1805
+12V Power Transformer
C1820 D1809
AMPPOWER
Q1806 C1825
7 -12V
See page 161
-12V
SCHEMATIC DIAGRAM
113
A B C D E F G H I J
RX-A3030/RX-V3075
1 WIRING DIAGRAMS
OVERALL ASSEMBLY
T model DIGITAL (3) FUNCTION (2)

PN35
W390
CB206 CB70 PN732 to FUNCTION (3) (W7603) to FUNCTION (3) (W7601)
CB9
(C, R, T, K, A, B, G, F, L, S, J models) (C, R, T, K, A, B, G, F, L, S, J models)
to VIDEO (1) CB21 W7602 FUNCTION (2)
(CB303) FUNCTION (1)
to VIDEO (1) CB22 DIGITAL (1)
2 AMPPOWER (2) (CB302)
CB701/CB735
POWER to AMPPOWER (1) CB952 CB943/CB731 W7004 CB709 (C, R, T, K, A, B, G, F, L, J models)

to VIDEO (1) CB702/CB734
(CB335) CB71 (W1800) W7003 (U model)
to AMPPOWER (1)
PN201 (W1806) CB924 W1800
CB10 CB944/CB733 W1802
W2005 CB703/CB732
CB11
POWER2 CB923
W2003 W1806 CB930 W7001 W7002 CB704 W1801
to FUNCTION (2) (CB738)
CB945/CB736 to OPERATION (2)
PN941
AMP (1) (CB454) to FUNCTION (3) (W7603)
CB76 (C, R, T, K, A, B, G, F, L, S, J models)
CB942 PN181 PN180
PN701 to VIDEO (1) (CB333)
CB73 PN943 CB74 CB81 (U model)
to Power transformer CB931 PN732 White side
CB75 CB77
CB738 CB113 to VIDEO (1) (CB331)
3 AMP (2)
W3701 to DIGITAL (1) (CB74)
W801 (C, R, T, K, A, B, G, F, L, S, J models)
CB112
AMPPOWER (3) R, S models
W1001 POWER U, C, R, K, A, B, G, F, L, S, J models

Flexible flat cable
AMP (4) TRANSFORMER
W1002 to VIDEO (1)
(CB303)
Letter side to DIGITAL (1)
(1-5/8")
43 mm
AMP (5) (CB21)
4 POWER to DIGITAL (1) PN302
(CB21) White side
White side
CB452 W330
CB454 to DIGITAL (1) Letter side
W4503 CB302
(CB22)
CB303
VIDEO (1)
PN463
W4501 FUNCTION (2)
to AMPPOWER (1)
PN361 W331 (W1802)
View A PN191 CB335 to FUNCTION (1)
PN404 to DIGITAL (1) (W7003)
(CB71)
White side
CB193
OPERATION (2) VIDEO (3) DIGITAL (2) CB333
PN331 CB331 CB334 (U model)
(U model) CB304
5 Flexible flat cable

to DIGITAL (2)
Front panel (View A) CB200
(CB31) OPERATION (2)
15 mm OPERATION (4) W4501
CB452 W330 W331
OPERATION (3)
CB453 CB454
(5/8") W4503 CB31 PN185
CB190 CB188 W801
PN186 CB189
Letter side
to Power transformer to Power transformer
CB471 to FUNCTION (3)

CB461 (CB806)
Flexible flat cable
CB402 5 mm
(1/4") Letter side
CB404 PN461
CB405 to FUNCTION (3)
6 L: 410 mm W4005
(CB806)
PN403 CB362 PN363
PN463 75 mm
VIDEO (3) to DIGITAL (1) (3")
PN362 (CB77)
PN361
PN404 Letter side 35 mm
PN462 Letter side (1-3/8")
165 mm (6-1/2")
Flexible flat cable to OPERATION (2)
(CB452)
to DIGITAL (1) PN401 CB401 L: 300 mm
OPERATION (1)
to DIGITAL (1)
(CB9) to DIGITAL (1) to FUNCTION (3) L: 500 mm
(CB77) (CB806)
to OPERATION (1)
7 20 mm (CB401)
to DIGITAL (1)
(3/4")
(CB9) to OPERATION (2)
75 mm (3")
(CB452)
114
A B C D E F G H I J
RX-A3030/RX-V3075
AMP UNIT
(C, R, T, K, A, B, G, F, L, S, J models)
AMPPOWER (2) FUNCTION (3)
W7602
POWER
W7602 to DIGITAL (1)
W1523 AMP (3) W7603
CB194 (CB924)
W7601
PN101
CB110
2
CB114
W1800 to DIGITAL (1)
to DIGITAL (1) (CB74)
(CB942) W1810 PN189
PN184 PN182 W1802
(U, C, R, K, A, B, G, F, L, S, J models)
W1806
W2002 PN188 to VIDEO (1)
PN183
CB202 CB180 (CB331)
W1801
CB181
PN202 W1807B
W1005 PN190 W1809
AMPPOWER (1) to FUNCTION (2)
PN187
AMP (1) W1807A (CB738)
W1808B to FUNCTION (3)
W1518A W1003
W1808A W1512A (CB806)
BU CB111 W1803
3 W1804 GY
AMP (2)
AMP (1) OR
W1519A
BR
W1513A
RE
BL
POWER W1516A
BL W1514A RE
GY
W1521A TRANSFORMER BL
BL W1517A
RE
W1520A
W1515A
BR
4 WH
W1522A Flexible flat cable AMP (2)

YE U model C, R, T, K, A, B, G, F, L, S, J models
12 mm
(1/2") to AM/FM TUNER
to FUNCTION (5)
(CB781) Letter side 15 mm
(5/8")
Letter side
to FUNCTION (3)
(CB762)
U, C, R, K, A, B, G, F, L, S, J models Letter side U model

5 Flexible flat cable
20 mm to HD Radio TUNER FUNCTION (5) U model
(3/4") 45 mm
W2004A (1-3/4")
W2004B U model Letter side
CB781
FUNCTION (5)
POWER U model
to FUNCTION (5)
(CB782)
CB782
W1526A
PN102
AMP (3) BL W1526B
W1521B BL
W1515B CB501 HD Radio to VIDEO (1)
W1514B W1518B W1522B to VIDEO (1)
OR TUNER (CB334)
AMPPOWER (2) W1512B BL (CB334)
to AMPPOWER (1) RE W1516B BR GY CB502
(CB193) YE W1513B
6 W1519B GY WH
BU
BL
T model W1517B
BR C, R, T, K, A, B, G, F, L, S, J models
to VIDEO (1)
W1520B (CB334)
AM/FM
TUNER
POWER2 (1)
to Power transformer
W7603 CB762
W7601
to DIGITAL (1) CB206 AMP (1)
(CB942) W2506
AMP (2)
PN204 PN205 W2505
7 FUNCTION (3)
to VIDEO (3) W2507
(CB361)
115
A B C D E F G H I J
DIGITAL (2) (CB31)
RX-A3030/RX-V3075
Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location Ref no. Location
IC13 D4 IC41 F5 IC58 D5 IC66 H2 IC75 E5 IC900 I4 IC913 G5 IC920 H5 IC937 I3 IC951 I3
CD_SENSE
FR_N_RST
PRINTED CIRCUIT BOARDS
FR_N_INT
1 IC14 E3 IC42 F5 IC60 G2 IC68 G2 IC76 F6 IC901 G3 IC914 H4 IC921 H6 IC938 I3 IC952 H3
FR_SDA
FR_SCL
ShieldC
DataC+
Shield0
Shield1
Shield2
Data0+
Data1+
Data2+
DataC-
Data0-
Data1-
Data2-
TPWR
Shield
IC15 C4 IC43 G4 IC61 G3 IC70 D5 IC77 G6 IC902 G3 IC915 H6 IC920 H6 IC939 D5 IC953 H4
CEC
+5H
+5H
PD
IC16 C4 IC47 F4 IC62 F3 IC71 D6 IC79 E5 IC903 H4 IC916 G6 IC930 I2 IC940 I6 IC955 I3
-
IC20 C3 IC50 F3 IC64 G4 IC72 D5 IC85 G6 IC910 G5 IC917 H6 IC932 I3 IC941 I6 IC956 I3
DIGITAL (1) (Side A) IC21 C4 IC53 F4 IC65 G4 IC73 D6 IC86 G6 IC911 G5 IC918 H4 IC934 I6 IC942 I5 IC960 H3
IC40 F4 IC54 F4 IC935 I3 IC943 I6 Q13 D4
No replacement part available. IC936 C5 IC944 I5 Q14 C4
HDMI HDMI OUT
AV 1 2 1 NETWORK DC OUT IC945 I5 Q17 C4
AV 7 AV 6 AV 5 AV 4 AV 3 AV 2 (1 BD/DVD) (ZONE OUT) ARC (3 NET) IC946 I5 Q19 B2
Q250 C4
2 DIGITAL (3) CB7 CB6 CB5 CB4 CB3 CB2 CB1 CB62 CB61 Q251 C4
(W390) CB932
232C_MISO
232C_MOSI
CB951 Q704 G6
4 IC66 Q705 G6
DGND
+3.3M
1
5 4
5 4
Q709 E6
IC68
IC60
5 8 1 5
IC930
1 3
CB70 1 3
128 97
1 75 51 75 51 3 4
96
76 50 50
128 97 76
1 1 8
IC2
96
IC960
VBUS
D-
D+
GND
FG
4 1
SVID_DET 1 14
+5VA
IC932
3 2 IC62 IC61
IC14 4 5
ADSY VE 1 36 28
IC1
CB21
VIDEO (1) ADSC VE

27 7 8
IC955
CB9
32 65
(CB303) DASY 33 64 100 26 100 26
DASC VE
9 19
32 1 25 1 25 18 11 10
65 10
33 64
IC937
OPERATION (2)
20 1
27
1 IC956 1 (W4501)
3 VE DAPr 1
97
96
4
11 10
VE FUNCTION (2)
IC938
9 8 5 8
DAPb 128
VE
IC901
(CB731)
IC4
IC952
DAY
CB22
VIDEO (1) VE 16 1
20 1
VE DACVBS
IC50
(CB302) 24 13 9 8
ADPr 25 12 28 54
NET_L
IC902
IC951
VE ADPb 32 65 56 29 NET_R
+5VA 33 64 16 NET_CPGND
ADY
IC20 1
ZONE2_CPGND
VE 36 1 8 ZONE2_L
ADCVBS 37 48 1 2 9 IC935 AGND_DA2
2 3
ZONE2_R
IC9
IC64
1 4 +5A
AGND_DA2 +5A
4 3
16 1
CB943
AGND_DA2
REM_IN2 AD_M_R
AD_M_L
IC953
L3_DET 7 1 AGND_AD
PS1_PRT 32 17 7 1 10 1 AD_Z2_R
VID_PON +3.3M 33 16 AD_Z2_L
DV_SCL 128 97 AGND_AD
DV_SDA 1 96 IC54 IC53 CB952 NC
NC
IC21
14 IC65
EX_MOSI NC 8 14 8 20
CB71
IC3
EX_SCK 11
FUNCTION (2)
EX1_N_CS 48 49 1
4 1
4 EX1_N_RST 64 IC47
3 2 (CB733)
NC NC
NC NC 32 65
NC HDR_N_RST 8 5
33 64 1 28
12 1 DA_CEN-
4
HDR_MISO DA_CEN+
IC914
IC13 4 1 5 13 48 1
13 12
HDR_MOSI IC43
3 8
1 48 AGND_DA
6 4 2 DA_SRR-
IC15 1 4 IC903 DA_SRR+
176 133 IC900 AGND_DA
IC40
DA_SRL+
CB944
1 132 3 1 24 37
VIDEO (1) MHLVB 25 36 24 37 DA_SRL-
IC918
1 3
CB10
25 36
DA_SRBR- AGND_DA
(CB335) MHLVB_GND 1 6
25 24
4 5
DA_SRBR+
IC16
3 8 5 8 5 8 5 AGND_DA
4
IC11 IC936 IC939 CB924 DA_SRBL+
DA_SRBL-
IC911
CB923
DIGITAL (2)
8
IC58
5
IC946 DA_FL- AGND_DA
4 1 4 1 4 IC75 4 1
(W331)
1
3 2 DA_FL+
DA_FR+
1 4
48 1 9 8 DA_FR-
No replacement part available.
IC944
176 133
CB11 1 132 16 1
132 89 44
89
AGND_DA +5DA
Semiconductor Location 8 5
133 88 45 88
DA_FPL-
5 +5.5V IC12 36 25 DA_FPL+ DA_FPR+
CB930
Ref no. Location 37 24

DA_FPR-
DGND
+1.8HL
+3.3HL
IC920
AGND_DA
CB945
DGND 1 4 20 11 20 11 1 54 1 54 54 28 IC942
DA_RPL-
D1 B2 DA_RPL+
IC72 IC70 8 5 48
13 DA_RPR+
IC79 IC913 1 12 DA_RPR-
D2 B2 DIGITAL (2) POWER IC910
IC945
AGND_DA
DA_SW2-
(W2003A)(W2003B) 1 10 1 10 4 3 DA_SW2+
IC42
(W330) DA_SW1+
IC41
D3 B2 1 4 5 1
DA_SW1-
POWER2 (1) 176 1 27 44 89
R_200_DET
AGND_DA
D4 C2 AMPPOWER (1) (W1806) (W2506) 20 11 20 11 45
45 88
+12V
36 25
D5 C2 (U, C, R, K, A, B, G, F, L, S, J models) IC73 IC71
1 44 8
IC921
5
37
IC943
24
+3.3M FUNCTION (2)

D6 C2 POWER2 (1) (W2505) DGND 1 10 1 10
27 28 27 28
8 1
54 28
48
ACPWR_DET IC85 3 1 4 1 13 (CB736)
CB942
1 2
D7 C2 MCPU_N_RST 16 1 4 IC922
12
IC76
IC77
D8 C2 Ref no. Location PRY 4 1
IC86
DEST 9
CB76
9 16 1
8 3 2 5
3
IC915
CB949 2 3
IC916 2
D9 D2 D24 C4 CB78
1 4
IC917 1 27 1 8
IC934
CB79 1 4 3 4
(for service)
+5D
DGND
VAUXD
IC941
AV1_D
AV2_D
AV3_D
AV4_D
AVOUT_D
AUDIO1_D
AUDIO2_D
+5DSP
NC
6 D10 D2 D251 C3 Ref no. Location 4
1 2
5
D11 D2 D252 C3 D608 F2 CB75

CB77 4 3
CB931 (Writing port) CB81 4 3
IC940
CB73 CB74
D12 D2 D400 F4 D609 F2 5
1
D13 D2 D401 F4 D611 G2
D14 D2 D402 F4 D612 G2 FUNCTION (2)
TUN_N_INT
TUN_N_RST
TUN_SCL
NC
TUN_SDA
NC
FLD_N_CS
FLD_MOSI
REM_IN1
IRB_GND
ISEL_RA
PS2_PRT
PSW_DET
KY_AD2
VDL_RB
FLD_PON
STBY_LED
+5.5
DGND
+5USB
GND
+5USB
GND
PS2_PRT
PS1_PRT
AMP_LMT
AMP_OLV
I_PRT
DC_PRT
EX_SCK
DGND
EX_MOSI
EX2_N_CS
EX2_N_RST
+3.3M
+3.3MT
MT_F_MI
MT_Z2
MT_MZ
MT_EX1_MI MT_SB_MI
MONO_N_Z2 MONO_N_Z3
VOL_MOSI
DGND
MT_HP
DGND
+3.3S
THM4
THM2
(W7301)
D15 E2 D403 F4 D9300 C6 FUNCTION (3)
THM1 (W7602)
D16 E2 D500 F3 D9303 I5 THM3
AMP (5) OPERATION (2) +3.3S
D17 E2 D502 F3 D9304 I5 (W1002) DGND Ref no. Location Ref no. Location
(W4503)
FLD_N_RST
FLD_SCK
MIC_N_DET
FLP_PON
IR_DATA
ISEL_RB
KY_AD3
KY_AD1
VDL_RA
PD_LED
+3.3M
+5.5
DGND
D18 E2 D503 E3 D9305 I6 Q710 E6 Q9302 D5
HP_N_DET
MT_Z3
MT_SB_PO
VOL1_SCK
VOL2_SCK
BAL_ATT
AMP (4)
D19 F2 D601 G2 D9306 I5 Ref no. Location Ref no. Location (W1001) Q719 E6 Q9304 D5
D20 F2 D602 G2 D9501 I4 IC2 C3 IC9 E3 AMPPOWER (1) Q9100 G6 Q9305 I6
7 (W1800)
FUNCTION (3) (W7601)
D21 F2 D604 G2 D9502 I4 IC3 E4 IC11 C5 (C, R, T, K, A, B, G, F, L, S, J models) Q9101 G6 Q9503 H3
FUNCTION (1) OPERATION (1)
D22 D4 D607 G2 IC1 D3 IC4 E3 IC12 D5 (CB401) Q9300 D6 Q9504 I3
(CB704)
116
A B C D E F G H I J
RX-A3030/RX-V3075
DIGITAL (1) (Side B)
IC56
5 4
IC18
2 3
IC55
1 4
1 3 4 1 3 4
IC57
3 2
2 1
1 2
4 3
IC10
3
54 28
IC954
27
1 5
1 IC5
3 4
IC952
28 27
2
3
IC51
5 4 IC22 4
1
IC52
1 3
10 1
4 54 1 10 1 10 1
IC25
11 20
IC24 IC23
11 20 11 20
1 5
3 4
IC17
Semiconductor Location
5 Ref no. Location Ref no. Location Ref no. Location
4
IC78
1 D25 I4 IC74 G6 Q12 F2
D501 F3 IC78 E5 Q15 E2
5 8
D700 F5 IC80 F5 Q16 E2
8 1 8 1
IC80
IC83
5 4 5 4
IC933
D701 E6 IC81 F6 Q18 H4
1
IC82
1
5
1 4
D702 F6 IC82 E6 Q252 H4
IC74
6 4 3 8 3 2
4 4
IC81 5
1 3 D703 E6 IC83 E5 Q253 H4
8
D704 E6 IC931 G6 Q258 H3
IC931
1
4 5
D9301 B3 IC933 G5 Q700 D6
D9302 B3 IC947 B6 Q701 D6
6 IC5 G3 IC954 C3 Q702 D6
4 3
IC10 I3 Q1 H2 Q703 D6
IC947
5 IC17 H4 Q2 H2 Q711 F5
1
IC18 G3 Q3 H2 Q712 F5
IC22 H4 Q4 H2 Q713 F5
IC23 F4 Q5 G2 Q714 F5
IC24 F4 Q6 G2 Q715 F5
IC25 F4 Q7 G2 Q716 F5
IC51 D4 Q8 G2 Q717 F5
IC52 E4 Q9 F2 Q718 F5
IC55 F3 Q10 F2 Q9301 G5
7 IC56 E3 Q11 E2 Q9303 B6
IC57 E3
117
A B C D E F G H I J
RX-A3030/RX-V3075
2 DIGITAL (2) (Side A) DIGITAL (3) (Side A)
DIGITAL (1)
VIDEO AUX (CB70)
232C_MOSI
232C_MISO
HDMI/
MHL
DGND
+3.3M
CB30
3 9 8
IC39
W390
DIGITAL (1)
(CB10) 16 1
22 1
W331
MHLVBF_GND
23 88
MHLVBF
No replacement part available. IC32 CB39

44 67
4 1 5 45 66
IC30
3 4
CB31
RS-232C
W330
+3.3HL
+1.8HL
DGND
Shield
Data2+
Data2-
Shield2
Data1+
Data1-
Shield1
Data0+
Data0-
Shield0
DataC+
DataC-
ShieldC
CEC
PD
CD_SENSE
FR_N_INT
+5H
+5H
NC
TPWR
FR_N_RST
FR_SCL
FR_SDA
DIGITAL (1)
(CB11)
5 DIGITAL (1)
(CB9)
Ref no. Location
6 D330 C3
D334 C3
IC30 C4
IC32 C4
IC39 H3
118
A B C D E F G H I J
RX-A3030/RX-V3075
2 DIGITAL (2) (Side B) DIGITAL (3) (Side B)
4
4 3
5 1
IC33
Ref no. Location
D331 C3
D332 C3
D333 C3
IC33 C4
6
119
A B C D E F G H I J
RX-A3030/RX-V3075
FUNCTION (1) (Side A)
PHONO AV 1 AV 2 AV 3 AV 4 AV OUT AUDIO 1 AUDIO 2 AUDIO 3 AUDIO 4 MULTI CH INPUT ZONE OUT PRE OUT
(1 BD/DVD) (2 TV) CENTER/ FRONT SURROUND SUR.BACK SUBWOOFER CENTER
2 FRONT SURROUND SUR.BACK ZONE 2 ZONE 3
SUBWOOFER (SINGLE)
L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R L/R 1/2
FUNCTION (2)
(CB732)
NET_L
NET_R
NET_E
N.C.
N.C.
N.C.
AUXL AUXR
AUXE
CB703
MIC
MICE
AD_M_R
AD_M_L
4 N.C.
AGND_AD
N.C.
AGND_AD
N.C.
OPERATION (2)
N.C. (CB454)
HPR
W7004
AGND E
AGND
DA_CEN HPL
DA_SR AGND HP_N_DET
AGND
DA_SL
CB702
AGND
DA_SBR
AGND
DA_SBL
AGND
DA_FL
AGND
DA_FR
5 FUNCTION (2)
(CB734)
CB709
DA_FPL
AGND2
DA_FPR
AGND2
DA_RPL
AGND2
DA_RPR
AGND3
CB701
DA_SW2
AGND3
DA_SW1
-12V W7002 W7001
-12V CB704
+12V +12V
6 CB708
FUNCTION (2)
(CB735)
BAL_ATT
VOL2_SCK
VOL1_SCK
MONO_N_Z2
MT_MZ MT_EX1_MI
MT_SB_PO
MT_Z3
HP_N_DET
MIEX1L
MISBL
MISL
MIFL
MICT
E
E
MISBR
E
MISR
E
MIFR
MIEX1R
C, R, T, K, A, B, G, F, L, S, J models
Ref no. Location
Q7018 D6
TUL
+5T
TUR
TUE
MT_HP
DGND
VOL_MOSI
MONO_N_Z3
MT_SB_MI
MT_Z2
MT_F_MI
+3.3MT
TUL
+5T
TUR
TUE
AMP (2) AMP (1) Q7019 D5

FUNCTION (3) (W7603) (CB112) (CB113)
VIDEO (1) (CB333) Q7022 I4
(U model) Q7023 I4
Q7036 D6
DIGITAL (1)
7 (CB73)
120
A B C D E F G H I J
RX-A3030/RX-V3075
FUNCTION (1) (Side B)
K, A, B, G, F, L models
3 8 5
4 1 IC704
IC703 1 4
4 1 4 1
5 8 51 50
IC708
IC705 1
4
5 8 5 8
4 1
IC711
31 4 1
30 5 8
1
70
IC707
IC
80
IC706
81 5 8
5 8
100 1
4 8 5
IC709
1 4
Ref no. Location Ref no. Location

IC708 I3 Q7029 G3
IC709 H4 Q7030 G3
5 IC711 G4 Q7031 G3
Q7001 F5 Q7032 H3
51 50 Q7002 F5 Q7033 H3
Q7003 F3 Q7034 H3
Q7004 F3 Q7035 I3
31
70
2 30 Q7005 F5 Q7037 G3
80 IC
81 Q7006 F3 Q7038 G3
Q7007 H6 Q7039 G3
Q7008 H6 Q7040 G3
100 1
Q7009 H6 Q7041 G3
Q7010 H6 Q7042 G3
6
Q7011 G6 Q7043 H3
Q7012 H6 Q7044 H3
Q7013 G6 Q7045 H3
U model C, R, T, K, A, B, G, F, L, S, J models
Q7014 H6 Q7046 H3
Semiconductor Location Q7015 G6 Q7047 H3
Ref no. Location Ref no. Location Q7020 I4 Q7048 I3
D7001 F5 IC702 D6 Q7021 I4 Q7049 I3
D7002 F3 IC703 B3 Q7024 H4 Q7058 G3
D7003 C6 IC704 F3 Q7025 H4 Q7059 G3
D7004 C5 IC705 F3 Q7026 H5 Q7060 H3
7 D7005 D6 IC706 G4 Q7027 H5 Q7061 H3
IC701 D4 IC707 H4 Q7028 G3 Q7062 I3
121
A B C D E F G H I J
RX-A3030/RX-V3075
FUNCTION (2) (Side A) FUNCTION (3) (Side A)

DIGITAL (1)
(CB943)
DIGITAL (1) DIGITAL (1)

(CB945) (CB944)
NET_CPGND
AGND_DA2
AGND_AD
ZONE2_R
ZONE2_L
AD-Z2_R
AD_M_L
NET_L
AMPPOWER (1)
AGND_DA
AGND_DA
DA_SRBR- DA_SRBR+
DA_SW1+
2
DA_SRBL+
DA_FPR+
DA_RPL+
DA_SW2-
DA_RPR-
DA_SRBL- AGND_DA
AGND_DA
AGND_DA
DA_FPL-
N.C.
DA_SRR+
DA_SRL+
+5A
(W1801)
DA_CEN-
DA_FL+
DA_FR-
+12V
+5A
AV 1 AV 2 AV 3 AV 4 AV OUT AUDIO 1 AUDIO 2
ZONE2_CPGND
AG1RETURN
AG2RETURN
COAXIAL COAXIAL OPTICAL OPTICAL OPTICAL COAXIAL
R_200_DET
AGND_DA2
AGND_DA2
AG1SENSE
AG2SENSE
DIGITAL (1)
AGND_DA
AGND_DA
AGND_DA
AGND_DA
AGND_AD
DA_SW2+
DA_CEN+
DA_RPR+
DA_SW1-
DA_SRR-
DA_FPL+
DA_FPR-
DA_SRL-
DA_RPL-
AD_M_R
DA_FR+
AD-Z2_L
(CB923)
DA_FL-
VAUXD
NET_R
DGND
+12V
-12V
N.C.
+5A
+5D
+5A
W7301
+5D
VAUXD
DGND CB738
AUXR
AUXE
AUXL
CB737
-12V
MICE
3 MIC
+12V
CB736 CB733 CB731
AUXV
AUXVE
AUXY AV1
AUXVE
AUXC AV2
AV3
AV4
W7602
OPERATION (2) AVOUT
AUDIO1
(CB452) AUDIO2
+5DSP W7601 W7603
DGND CB762
DIGITAL (1)
(CB924)
DGND
TUN_SDA
DGND
TUN_SCL
TUN_N_RST
TUN_N_INT
+5T
TUR
TUE
TUL
INT
GND
+5T
SDA
4
RESET
SCL
N.C.
ROUT
LOUT
W7302
DIGITAL (1) (CB81) FUNCTION (1) (CB709)

(C, R, T, K, A, B, G, F, L, S, J models) (C, R, T, K, A, B, G, F, L, S, J models)
AM/FM TUNER
CB735 CB734 CB732
5
AGND
AGND
AGND
AGND
AGND
AGND
AGND
N.C.
AD_Z2_L
AGND_AD
AD_M_R
MIC
AUXR
ZONE2_E
ZONE2_L
NET_R
+12V
-12V
AGND3
AGND3
AGND2
AGND2
AGND2
AUXC
DA_FR
DA_FL
DA_SBL
DA_SBR
DA_SL
DA_SR
DA_CEN
AGND
R_200_DET
FUNCTION (5)
+12V
-12V
DA_SW1
DA_SW2
DA_RPL
DA_FPR
DA_FPL
DA_RPR
AUXY (Side A)
N.C.
AGND_AD
AD_Z2_R
AD_M_L
MICE
AUXE
AUXL
ZONE2_R
NET_E
NET_L
AUXVE
AUXV
N.C. U model
N.C.
N.C.
N.C.
IPVE FUNCTION (1)
N.C. FUNCTION (1) (CB702)
(CB701) FUNCTION (1)
6 VIDEO (1)
(CB703)
(CB304)
I2C_SCL
I2C_SDT
TXD GND
RXD TXD
RESET RXD
SPDIF GND
CB782
GND RESET
CB781
VIN_3.3V SPDIF
GND GND
AUDIO_OUT_L GND
AUDIO_OUT_M AUDIO_OUT_R VIN_3.3V
VIN_3.3V
GND AUDIO_OUT_L
AUDIO_OUT_M
AUDIO_OUT_R
VIDEO (1)
(CB334) HD RADIO TUNER
7
122
A B C D E F G H I J
RX-A3030/RX-V3075
FUNCTION (2) (Side B) FUNCTION (3) (Side B)
3 8 14
7 1
IC762 IC761
8 14
1 7
4 1 4 1 4 1
4 1 4 1
4 1
4 1
IC377 IC731 IC733
IC375 IC376
IC734
4 5 8
5 8
5 8
5 8
5 8
5 8
IC732
5 8
FUNCTION (5) (Side B)

U model
Ref no. Location
6 IC731 D4
IC732 E4
IC733 E4
IC734 D4
IC735 B4
IC736 C4
IC737 C4
IC761 I3
IC762 H3
123
A B C D E F G H I J
RX-A3030/RX-V3075
OPERATION (1) (Side A)
Remote control
sensor
DIGITAL (1)
(CB77)
FLD_N_RST HDMI Through/iPod Charge

FLD_N_CS indicator
FLD_SCK
FLD_MOSI
MIC_N_DET
REM_IN1
3 IRB_GND
FLP_PON
IR_DATA
ISEL_RA
ISEL_RB
PS2_PRT
CB401
KY_AD3
PSW_DET
KY_AD1
KY_AD2 SW425 MAIN ZONE
VOL_RA
VOL_RB
PD_LED
FLD_PON
+3.3M
STBY_LED
+5.5
+5.5
DGND DGND
FLP_PON
FLAC
4 FLAC
W4005
VOL_RA FGND
VOL_RB 44V
CB405
DGND PRESET SCENE TONE/ DGND

PSW +5.5
PD_LED
INFO 4 3 2 1 STRAIGHT BALANCE OPTION ON SCREEN
SW401
SW404
+5.5
SW403
SW402
SW414
SW409
SW407
CB402
SW410
SW408
SW405
SW406
SW411
CB404
SW412 VIDEO (3)
(CB362)
OPERATION (3) MEMORY
+12V
MICE
MIC_N_DET
ISEL_RA
ISEL_RB
+3.3M
DGND
SW421 SW418 SW428 SW426
(CB461) MULTI ZONE
SW415
SW423
SW420
SW424
SW417
SW413 SW416
SW430 OPERATION (4)

ENTER (CB471)
OPERATION (2)
TUNING ZONE ZONE 4 ZONE 3 ZONE 2 PROGRAM (CB453)
5 CONTROL SW429 SW427
AM FM
DISPLAY RETURN
6
Ref no. Location
D4001 I3
124
A B C D E F G H I J
RX-A3030/RX-V3075
OPERATION (1) (Side B)
4 3
4 1
2
IC401
Ref no. Location
D4002 B3
6 D4003 A3
D4006 F3
D4007 F3
IC401 B4
Q4001 H3
Q4002 B3
125
A B C D E F G H I J
RX-A3030/RX-V3075
FUNCTION (2)
(CB737) FUNCTION (1) OPERATION (1)
OPERATION (2)
DGND
(Side A)
AUXE
AUXV
AUXY
AUXC
(W7004) (CB402)
-12V
+5D
MIC
MIC N_DET
HP_N_DET
AUXVE
AUXVE
VAUXD
AUXR
AUXL
MICE
MICE
+12V
+12V
HPR
HPE
HPL
CB453
2 CB452
GND
+5USB
GND
+5USB
CB454
W4503 DIGITAL (1)

(CB931)
JK451
W4501
FG
GND
+Data
-Data
VBus
3
DIGITAL (1)
(CB952)
JK453
CB455
4
OPTICAL R AUDIO L VIDEO PHONES YPAO MIC
SILENT CINEMA USB jack
VIDEO AUX
OPERATION (3) (Side A) OPERATION (4) (Side A)

OPERATION (1)
(CB404)
5
ISEL_RA
ISEL_RB
DGND
+3.3M
CB471
SW471
SW462
SW461
6 INPUT
PURE DIRECT PURE DIRECT

VOLUME indicator
CB461
+5.5
PD_LED
PSW
DGND
VOL_RB
VOL_RA
Ref no. Location

D4603 E6
OPERATION (1)
(CB405)
7
126
A B C D E F G H I J
RX-A3030/RX-V3075
OPERATION (2) (Side B)
8 5
IC451
1 4
Ref no. Location
D4501 C3
D4502 C3
3 D4503 D3
D4504 D3
D4506 C3
D4507 E3
D4508 E3
D4509 F3
D4510 E3
D4512 F3
D4514 F3
IC451 G2
Q4501 G2
4
Q4601 E6
OPERATION (3) (Side B) OPERATION (4) (Side B)
127
A B C D E F G H I J
RX-A3030/RX-V3075
AMP (1) (Side A) AMPPOWER (1)

(W1808B)
AMPPOWER (1)
(W1808A)
AMPPOWER (1)
(W1809)
+B
CB108
CB111
3 +B
CB105
-B
CB107
CB109
-B For service
CB106 For service
For service For service
I_PRT_L For service
W1005
-LB_L W1517A
+LB_L W1522A
W1521A
AMPPOWER (1)
(CB180) W1518A
AMP (3) BL W1519A

(W1518B)
4
W1520A
CB113
BR GY BL WH YE AMP (4) (Side A)

C
E AMP (3) AMP (3) AMP (3) AMP (3) AMP (3)
FL (W1519B) (W1521B) (W1517B) (W1520B) (W1522B)
SL
E
SBL
EX1L
6 E
IC100
FUNCTION (1) Ref no. Location Ref no. Location Ref no. Location OUT GND VCC
(W7001)
IC100 J6 Q1067 E4 Q1075P F2 DGND
W1001
IC102 J7 Q1068 F4 Q1077N H2 +3.3S
THM3
Q1060 B4 Q1069 H4 Q1077P F2 THM1
VCC GND OUT
Q1061 C5 Q1070 F4 Q1079N C2
IC102
Q1062 E4 Q1071 H4 Q1079P B2 DIGITAL (1)
Q1063 F5 Q1072 B4 Q1081N D2 (CB76)
Q1064 H5 Q1073 D4 Q1081P D2 C model

7 Q1065 B4 Q1074 E4 Q1083N E2
Q1066 D4 Q1075N G2 Q1083P E2
128
A B C D E F G H I J
RX-A3030/RX-V3075
AMP (1) (Side B)
2
D1024 B5 Q1040 B5
D1025 C5 Q1041 C4
D1026 E5 Q1042 E4
D1027 F5 Q1043 F4
D1028 H5 Q1044 H4
D1029 B4 Q1045 B5
D1030 B4 Q1046 C5
D1031 C5 Q1047 D5
D1032 C5 Q1048 F5
3 D1033 D4 Q1049 G5
D1034 D4 Q1050 B5
D1035 F5 Q1051 C5
D1036 E5 Q1052 E5
D1037 G5 Q1053 F5
D1038 G5 Q1054 H5
D1039 F4 Q1055 B4
D1040 G4 Q1056 C4
D1041 B4 Q1057 D4
D1042 C4 Q1058 F4
D1043 D4 Q1059 G4
4
D1044 H3 Q1085 H3
D1045 G3 Q1086 G3
D1046 C4 Q1087 C3
D1047 D3 Q1088 D3
D1048 E4 Q1089 E3
AMP (4) (Side B)
C model
7
129
A B C D E F G H I J
RX-A3030/RX-V3075
AMP (2) (Side A) AMPPOWER (1) AMPPOWER (1)

(W1807B) (W1807A)
3
CB104
CB103
CB102 CB101
For service I_PRT_R
For service
W1003
For service -LB_R
For service +LB_R
W1516A
W1514A W1512A
AMPPOWER (1)
(CB181)
W1515A GY
AMP (3)
(W1512B)
4
W1513A
CB112
BR RE BL OR AMP (5) (Side A)
FR
AMP (3) AMP (3) AMP (3) AMP (3)
(W1514B) (W1516B) (W1513B)
E
(W1515B)
SR
E
SBR
EX1R
6
Semiconductor Location FUNCTION (1) IC101
(W7002) OUT GND VCC
Ref no. Location Ref no. Location Ref no. Location

DGND
Q1022 E4 Q1030N G2
W1002
IC101 J6 +3.3S
IC103 J7 Q1023 B4 Q1030P G2 THM4
THM2
Q1016 B4 Q1024 G4 Q1032N F2 VCC GND OUT
Q1017 G5 Q1025 F4 Q1032P E2 IC103

DIGITAL (1)
Q1018 E5 Q1026 D4 Q1034N E2 (CB75)
Q1019 D4 Q1027 C4 Q1034P D2
C model
7 Q1020 D4 Q1028N C2
Q1021 G4 Q1028P C2
130
A B C D E F G H I J
RX-A3030/RX-V3075
AMP (2) (Side B)
D1000 C5 Q1000 G4
D1001 D5 Q1001 E4
D1002 G5 Q1002 D4
D1003 E5 Q1003 B4
D1008 C4 Q1004 G5
3
D1009 C4 Q1005 E5
D1010 G5 Q1006 D5
D1011 G5 Q1007 B5
D1012 E5 Q1008 G5
D1013 E5 Q1009 E5
D1014 B5 Q1010 D5
D1015 B5 Q1011 C5
D1016 F4 Q1012 G4
D1017 D4 Q1013 E4
D1018 B4 Q1014 D4
4 D1019 E4 Q1015 B4
D1020 C3 Q1036 C3
D1021 F3 Q1037 F3
D1022 D4 Q1038 D3
D1023 G3 Q1039 G3
AMP (5) (Side B)
C model
7
131
A B C D E F G H I J
RX-A3030/RX-V3075
AMP (3) (Side A)
AMPPOWER (1)
(W1803A)(W1803B)
AMPG
AMPG
2
AMPPOWER (1)
(W1810)
SPRY_F_RP_CTRL
SPRY_ZRP_CTRL
SPRY_ZFP_CTRL
SPRY_SR_CTRL
SPRY_SB_CTRL
SPRY_C_CTRL
SPRY_F_CTRL
AMP (1) AMP (2) AMP (1) AMP (1) AMP (2) AMP (1) AMP (2) AMP (2)
AMP_OLV
(W1520A) (W1514A) (W1518A) (W1517A) (W1516A) (W1522A) (W1515A) (W1513A)
DC_PRT
RYB-
WH RE BU BL BL BL YE BR OR
3
CB114
W1519B
AMP (1) BR
W1520B
(W1519A)
W1512B
W1517B
AMP (2) GY CB110
(W1512A)
W1518B
W1514B
W1516B
W1515B
W1522B
FPR
W1521B
W1513B
W1523
FPL
4 RE
LE
(for service) GY AMP (1)
(W1521A)
W1526B
AMPPOWER (2)
(CB194)
W1526A
5
+/- +/- +/- +/- +/- +/- +/- +/- +/-

L R L R L R L R
FRONT CENTER ZONE 2/ZONE 3/R. PRESENCE SURROUND BACK SURROUND
SPEAKERS
132
A B C D E F G H I J
RX-A3030/RX-V3075
AMP (3) (Side B)
Ref no. Location
D1512 C3
D1513 H4
D1514 G4
D1515 D3
6 D1516 H4
D1517 C3
D1518 G3
D1519 E3
D1520 C3
D1521 C3
D1523 E3
D1524 H3
D1526 F3
D1527 B3
D1528 B3
7
D1529 B3
133
A B C D E F G H I J
RX-A3030/RX-V3075 Safety measures
Some internal parts in this product contain high voltages and are dangerous. Be sure to take safety measures during servicing, such
as wearing insulating gloves. OFF
Note that the capacitors indicated below are dangerous even after the power is turned off because an electric charge remains and a 5 k /10 W 30
1 high voltage continues to exist there. Before starting any repair work, connect a discharging resistor (5 k-ohms/10 W) to the terminals AMPPOWER1P.C.B. C1822 1828
of each capacitor indicated below to discharge electricity. The time required for discharging is about 30 seconds per each.
C1822-1828 on AMPPOWER (1) P.C.B.
AMPPOWER (1) (Side A)

POWER TRANSFORMER
AMP (3) POWER TRANSFORMER POWER TRANSFORMER
5 k-ohms 5 k-ohms
(CB110)
10 W 10 W
BL BL (for service)
2
CB182
CB189
CB190
W1803B W1803A
CB188
5 k-ohms
10 W
AMP (1)
(ST101)
3 AMP (1)
(ST102)
W1807A
POWER TRANSFORMER
IC180 IC181
W1808A
OUT COM IN OUT COM IN
W1809
CB200 W1808B W1807B
FUNCTION (2)
(CB738)
4
+5A
AG2_SENS
AG2_RETURN
W1801
CB180
+12V
CB181
AG1_SENSE
-12V
CB202
AG1_RETURN
CB203
CB193
(for service) TRG_GND

+18V
-7V
W1802
V_GND
+7V
W1800
IC183
5
W1806
VIDEO (1)
(CB331)
W1810
RYB-
SPRY_ZRP_CTRL
SPRY_F_RP_CTRL
SPRY_ZFP_CTRL
SPRY_C_CTRL
SPRY_F_CTRL
SPRY_SB_CTRL
SPRY_SR_CTRL
AMP_OLV
DC_PRT
U, C, R, K, A, B, G, F, L, S, J models
DGND 5 k-ohms 5 k-ohms AMP (2) 5 k-ohms 5 k-ohms
+5.5V DST
PRY +3.3M (ST103)
EX2_N_RS 10 W 10 W +B 10 W 10 W
MCPU_N_RST +LB_L +LB_R
ACPWR_DET EX2_N_CS
POWER -LB_L -LB_R EX_MOSI +B
DGND I_PRT_L I_PRT_R
6 (W2005) +3.3M
DGND AMP (2) -B
EX_SCK (ST104) -B
DC_PRT Semiconductor Location
AMP (1) AMP (2) I_PRT
DIGITAL (1) (CB942) (W1005) (W1003) AMP_OLV AMP (1)
POWER (U, C, R, K, A, B, G, F, L, S, J models) AMP_LMT Ref no. Location Ref no. Location
AMP (3) PS1_PRT (CB111)
(W2004A)(W2004B) D1807 H5 Q1806 H3
(CB114) PS2_PRT
D1808 D3 Q1808 D4
DIGITAL (1) D1809 G4 Q1809 D4
(CB74) D1810 H4 Q1810 D5
IC180 H3 Q1811 E5
IC181 H3 Q1815 E4
IC183 C5 Q1836 C5
7 Q1804 I3 Q1839 D5
Q1805 I3
134
A B C D E F G H I J
RX-A3030/RX-V3075
AMPPOWER (1) (Side B)
3 1
4 5
12 1
5 IC182
13 24
6
Ref no. Location Ref no. Location Ref no. Location Ref no. Location
D1801 I4 D1818 C5 Q1814 H4 Q1827 C5
D1802 H4 D1819 C5 Q1818 D5 Q1828 D5
D1803 H4 D1820 C4 Q1819 C5 Q1829 D5
D1804 D5 D1821 D4 Q1820 D5 Q1830 D5
D1805 D5 D1822 D5 Q1821 C5 Q1831 D5
D1811 C2 IC182 E5 Q1822 C2 Q1832 D5
D1814 B5 IC184 B5 Q1823 D5 Q1833 D5
D1815 C5 Q1807 E4 Q1824 D5 Q1837 C5
D1816 B5 Q1812 I4 Q1825 C5
7
D1817 C5 Q1813 H4 Q1826 C3
135
A B C D E F G H I J
RX-A3030/RX-V3075
AMPPOWER (2) (Side A) AMPPOWER (3) (Side A) AMPPOWER (4) (Side A)

R, S models
2 SPEAKERS
VOLTAGE SELECTOR
ZONE 2/ZONE 3/F. PRESENCE/BI-AMP
R L 220V 240V 110V 120V
+/- +/-
3 CB198 CB199
CB201
OR
PU
RE
YE
POWER TRANSFORMER
AMPPOWER (5) (Side A)
LE
CB194
RE
FPL
5
FPR
AMP (3)
(W1523)
136
A B C D E F G H I J
RX-A3030/RX-V3075
AMPPOWER (2) (Side B) AMPPOWER (3) (Side B) AMPPOWER (4) (Side B)

R, S models
AMPPOWER (5) (Side B)
137
A B C D E F G H I J
1 high voltage continues to exist there. Before starting any repair work, connect a discharging resistor (5 k-ohms/10 W) to the terminals POWER P.C.B. C2016
C2016 on POWER P.C.B.
POWER (Side A) 5 k-ohms

10 W
IC203
IC204
+5.5V
DGND
W2005
AMPPOWER (1)
W2003A W2003B (CB202)
RE GY
DIGITAL (1)
4 (CB930)
W2002
+5.5V
DGND
5
VIDEO (3)
(CB361)
AC IN Semiconductor Location
6
CB204
Ref no. Location

D2001 D3
D2002 F3
D2004 E4
D2010 E5
CB205
IC203 G3
W2004A W2004B IC204 G3
Q2001 F4
BU WH
7 AMPPOWER (1)
(CB193)
138
A B C D E F G H I J
RX-A3030/RX-V3075
POWER (Side B)
9
16
IC201
1 8
K R A
3
IC205
4
6 Ref no. Location
D2003 F3
D2006 E4
D2007 F3
D2016 F3
IC201 E3
IC205 G3
139
A B C D E F G H I J
1 high voltage continues to exist there. Before starting any repair work, connect a discharging resistor (5 k-ohms/10 W) to the terminals POWER21P.C.B. C2016
C2016 on POWER2 (1) P.C.B.
POWER2 (1) (Side A)

T model
5 k-ohms DGND VIDEO (3)
DIGITAL (1) (CB361)
(CB930) +5.5V
10 W
RE BL
W2507A W2507B
2
W2506
IC203
IC204
Ref no. Location
D2001 D3
D2002 E3
D2004 E3
4 D2010 G4
IC202 D6
IC203 G3
IC204 G3
Q2001 E4
Q2002 E6
CB206
CB204 CB205
AC IN
W2505
+3.3M
DGND
ACPWR_DET
MCPU_N_RST
PRY
DEST
6
IC202
DIGITAL (1)
(CB942)
POWER TRANSFORMER
7
140
A B C D E F G H I J
RX-A3030/RX-V3075
POWER2 (1) (Side B)

T model
IC205
RA K
16 9
IC201
1 8
Ref no. Location
D2003 F3
D2006 E4
D2007 E3
D2009 C6
5 D2011 E6
D2012 F6
D2013 F6
D2014 F6
D2015 F6
D2016 F3
D2017 D6
3 1
IC201 E3
IC207
4 5 IC205 G2
IC207 F6
Q2003 F6
6 Q2004 E6
141
A B C D E F G H I J
RX-A3030/RX-V3075
VIDEO (1) (Side A)

J model
AV 1 AV 2 AV 3 AV 4 AV OUT MONITOR OUT/ D4 VIDEO COMPONENT VIDEO MONITOR OUT/

(1 BD/DVD) ZONE OUT ZONE OUT
AV 1/AV 2 AV 3/AV 4
Y PB PR Y PB PR Y PB PR REMOTE TRIGGER OUT
2 1 2 1/2
IN OUT IN OUT
JK335
CB301 JK331 JK332
JK301 JK302
3
DIGITAL (1)
(CB22)
DGND
DAPr
VE
ADPb
VE
DAY
VE
CB302
DACVBS
VE
ADPr
VE
CB303 ADPb
+5VA
ADY
ADCVBS VE
REM_IN2
L3_DET
+3.3M PS1_PRT
VID_PON
HDMI_SCL
HDMI_SDA
IR_OUT
CB335
EX_MOSI
EX_SCK EX1_N_CS
EX1_N_RST
NC
NC
IRB_MOSI
IRB_MISO
TUN_N_INT
TUN_N_RST/HDR_N_RST
TUN_SCK/HDR_MISO
TUN_SDA/HDR_MOSI
5 DIGITAL (1)
(CB71)
1 4 1 4
IC331 IC332
CB304 CB333 CB334 CB331 Semiconductor Location

Ref no. Location
6
+5T
TUR
TUE
TUL
AUXC
R_200_DET
AUXY
AUXVE
AUXV
+3.3V
IPV
-3.3V
IPSY
IPVE
IPSC
TRG_GND
+18V
-7V
VGND
+7V
SDA
HDR_MOSI
NC
+3.3HDR
AUDIO_L
AUDIO_R
U model D3310 H3
D3311 H3
IC331 E6
DASC
DASY
ADSC
ADSY
SVID_DET
FUNCTION (2) FUNCTION (1) (W7003) AMPPOWER (1) IC332 F6
SCL
HDR_MISO
RESET
HDG
HDG
AUDIO_M
HDG
(U model) (W1802)
(W7302) Q3304 G6
Q3315 I3
VE
VE
VE
+5VA
Q3316 I3
FUNCTION (5) (CB782) DIGITAL (1)
(U model) (CB21)
142
A B C D E F G H I J
RX-A3030/RX-V3075
VIDEO (1) (Side B)
2
J model
16 9 16 9
IC303 IC301
1 8 1 8
51 50
14 8
IC307
31
16 9 16 9 30
7 IC305
1 80
IC304 IC302
81
1 8 1 8
4
100 1
16 9 24 13
IC306
IC308
7 1
1 12
IC309 1 8
8 14 Semiconductor Location
5 D3001 A3 IC303 B3
D3002 B3 IC304 B4
D3003 B3 IC305 D4
D3004 B3 IC306 G4
D3005 A3 IC307 C4
D3006 B3 IC308 C4
D3007 B3 IC309 B5
D3008 C3 Q3001 C3
D3017 C4 Q3002 C3
D3018 C4 Q3003 C3
D3302 H3 Q3004 G5
6
D3303 E5 Q3303 F6
U model U model
D3304 E5 Q3305 F6
D3312 H2 Q3306 F6
D3313 H2 Q3311 H3
D3314 H3 Q3312 I3
D3315 D6 Q3313 H3
D3318 H5 Q3314 I3
D3319 H5 Q3317 H3
IC301 B3 Q3318 I3
IC302 B4 Q3319 G4
7
143
A B C D E F G H I J
RX-A3030/RX-V3075
VIDEO (3) (Side A) VIDEO (3) (Side B)
POWER
(W2002B)
2 POWER2 (1)
OPERATION (1) (W2507A)(W2507B)
(W4005)
FLP_PON
DGND
FGND
DGND
FLCA
FLCA
+44V
5.5
5.5
CB362 CB361
Ref no. Location
D3601 G4
D3602 G4
D3603 G4
D3604 G4
D3605 F4
5 D3606 F4
D3607 F4
D3608 G3
D3609 G3
Q3601 G4
Q3602 G5
Q3603 G5
Q3604 G5
Q3605 F4
Q3606 C3
Q3607 G3
6 Q3608 C3
144
A B C D E F G H I J K L M N
RX-A3030/RX-V3075
SCHEMATIC DIAGRAMS Page 146 K7 Page 146 L2 Page 146 I7
DIGITAL 1/10 to DIGITAL (2)_CB31 to DIGITAL (2)_W331 to DIGITAL (2)_W330
1 HDMI
DGND
R223
CB9 5 6 7 8
502231-2400
0X4
WY78680
AV 7 AV 6 AV 5 AV 4 AV 3 AV 2 AV 1 4 3 2 1
CB10
CB11
XHI
XHI
(1 BD/DVD)
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
MHLVB_GND
CB7
HDMI IN-7 CB6
HDMI IN-6 CB5
HDMI IN-5 CB4
HDMI IN-4 CB3
HDMI IN-3 CB2
HDMI IN-2 CB1
HDMI IN-1
+3.3HL
+1.8HL
DGND
0 MHLVB
DC1RS19JAXR190 DC1RS19JAXR190 DC1RS19JAXR190 DC1RS19JAXR190 DC1RS19JAXR190 DC1RS19JAXR190 DC1RS19JAXR190
IC14: RP130Q501D-TR-F
0.1/10(BJ)
0.1/10(BJ)
Voltage regulator
C214
FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG FG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 FG
4 Data2+
CD_SENSE
FR_N_INT
FR_N_RST
EXC24CH500U Shield
Data2-
FR_SCL
FR_SDA
Shield2
Shield1
Shield0
ShieldC
+5H
TPWR
4 Data1+
4 Data0+
4 DataC+
CEC
no_use
3 Data1-
3 Data0-
3 DataC-
PD
C207
Reserved
SCL
SDA
GND
+5VPower
HPD
Reserved
SCL
SDA
GND
+5VPower
HPD
Reserved
SCL
SDA
GND
+5VPower
HPD
Reserved
SCL
SDA
GND
+5VPower
HPD
Reserved
SCL
SDA
GND
+5VPower
HPD
Reserved
SCL
SDA
GND
+5VPower
HPD
SCL
SDA
GND
+5VPower
HPD
Reserved
+5H
Shield2
Shield1
Shield0
ShieldC
Shield2
Shield1
Shield0
ShieldC
Shield2
Shield1
Shield0
ShieldC
Shield2
Shield1
Shield0
ShieldC
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
Data2+
Data2-
Data1+
Data1-
Data0+
Data0-
DataC+
DataC-
CEC
CEC
CEC
CEC
CEC
CEC
CEC
C213
BKP1005HS680-T
Shield2
Shield1
Shield0
ShieldC
Shield2
Shield1
Shield0
ShieldC
Shield2
Shield1
Shield0
ShieldC
L35
DGND
BLM21PG600SN1D
DGND DGND DGND DGND DGND DGND DGND DGND
no_use
3
0.1/10(BJ)
VDD 4 3 VOUT
J2
J1
0
R216 10K
L47
C181
(2125)
L31
L33
L32
L34
R207 22
R203 22
R204 22
R208 22
R209 22
R200 0
TP1 TP4 TP10 TP12 TP18 TP20 TP27
A
+3.3HL
+1.8HL
1
2
1
+Vf
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1
BKP1005HS680-T
D12
D15
D18
D21
DGND
L36
D3
D6
D9
DGND DGND DGND DGND DGND DGND
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
ESD7004MUTAG
DGND 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 DGND 6 7 8 9 6 7 8 9 6 7 8 9
5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 5 4 3 2 1 +5.5V
R109
R153
R173
R192
D11
D14
D17
D20
DGND
R36
R72
R87
D10
D13
D16
D19
D2
D5
D8
R107
R114
R149
R162
R171
R177
R189
R197
D1
D4
D7
TP2 TP5 TP11 TP13 TP19 TP21 TP30
R30
R45
R70
R76
R85
R98
1K
1K
1K
1K
1K
1K
1K
Vref
10K
10K
10K
10K
10K
10K
10K
10
10
10
10
10
10
10
6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9 6 7 8 9
22
22
22
22
22
22
22
R103 22
22
R144 22
22
R168 22
22
R185 22
D24
2 Q2 Q4 Q6 Q8 Q10 Q12 Q16
TMDS
TMDS
TMDS
TMDS
TMDS
TMDS
TMDS
Current Limit
R110
R154
R174
R193
100K
100K
100K
100K
100K
100K
100K
R37
R73
R88
R40 R75 R97 R113 R160 R176 R196 IC16
R102
R143
R167
R184
R25
R65
R82
RB521S-30TE61
R24
R64
R81
R169
R68
CE 1 2 GND NCP380HMUAJAATB
47K
47K
1K 1K 1K 1K 1K 1K 1K R1171S501B-E2-F
C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR
R105
R147
R187
5.0
no_use
no_use
no_use
no_use
no_use
no_use
no_use
MHLVB OUT IN VOUT VDD
R28
R83
47K
47K
47K
47K
47K
DGND DGND DGND DGND DGND DGND DGND
6
R108
R151
R172
R191
R32
R71
R86
ILIM GND GND GND
R170
R249
R38 R74 R96 R112 R159 R175 R194
R69
5
47K
47K
RB051L-40
10/10
10/10
10
C217
C220
10K 10K 10K 10K 10K 10K 10K /FLAG EN CE NC
4
105
R106
R148
R188
Q1 Q3 Q5 Q7 Q9 Q11 Q15
R29
R84
D25
47K
47K
47K
47K
47K
R237 R240
R242
C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR C4081UBTLR IC15
no_use
R243
Pin No. Symbol Description
C221
DGND DGND DGND DGND DGND DGND DGND
22K
1/25
18K 2.7K
R241
1 CE Chip Enable ("H" Active) ( 0 . 5 % )( 0 . 5 % )
no_use
IN6_B_5VPWR
IN2_B_5VPWR
(0.5%)
IN5_C_5VPWR
IN4_D_5VPWR
IN1_C_5VPWR
IN5_C_SCL
IN4_D_SCL
IN1_C_SCL
IN7_A_5VPWR
IN3_A_5VPWR
IN5_C_SDA
IN4_D_SDA
IN1_C_SDA
FR_D_5VPWR
IN6_B_SCL
IN6_B_SDA
IN2_B_SCL
IN2_B_SDA
2 GND Ground Pin
105
105
105
105
105
105
100
IN7_A_SCL
IN7_A_HPD
IN6_B_HPD
IN3_A_SCL
IN3_A_HPD
IN2_B_HPD
IN7_A_SDA
IN5_C_HPD
IN4_D_HPD
IN3_A_SDA
IN1_C_HPD
Q14 Q17
3 VOUT Output Pin A1576UBTLR
0.1/10(BJ)
TC7SET08FU
no_use
4 VDD Input Pin
no_use
R228
C205
220K
D23
IC17
J4
J5
0
DGND
2
1
DTC044EUBTL
DGND R244 +5H
10K
R230
R236
0.1/10(BJ)
100K
47K
V+
C219
Q18
IC15: R1171S501B-E2-FE +1.8HSW +1.8HSW DGND
3
V-
5 IC17
BLM21PG600SN1D L14 BLM21PG600SN1D L28

CMOS-based LDO regulator IC
R229
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
5.1K
BLM21PG600SN1D BLM21PG600SN1D
0.01/16(B)
0.01/16(B)
0.1/10(BJ)
0.1/10(BJ)
0.01/16(B)
0.01/16(B)
0.1/10(BJ)
0.1/10(BJ)
+3.3H +3.3H
1000P(B)
1000P(B)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
L4 L18
10/10
10/10
C150
C157
C161
C166
+5H
1000P(B)
1000P(B)
C152
C156
C169
DGND
C71
C81
C85
C88
C104
C74
C79
C91
10/10
10/10
C100
C14
C22
C25
C112
C17
C103
C106
C110
C29
C98
C15
DTC044EUBTL
C20
C23
C27
RXC_1-
RXC_0+
RXC_0-
RXC_1-
RXC_0+
RXC_0-
RXC_1+
RXC_1+
RXA_2+
RXA_2-
RXA_1+
RXA_1-
RXA_0+
RXA_0-
RXA_C+
RXA_C-
RXB_2+
RXB_2-
RXB_1+
RXB_1-
RXB_0+
RXB_0-
RXB_C+
RXB_C-
RXC_2+
RXC_2-
RXA_2+
RXA_2-
RXA_1+
RXA_1-
RXA_0+
RXA_0-
RXA_C+
RXA_C-
RXB_2+
RXB_2-
RXB_1+
RXB_1-
RXB_0+
RXB_0-
RXB_C+
RXB_C-
RXC_2+
RXC_2-
RXC_C+
RXC_C-
RXC_C+
RXC_C-
DGND
TVDD
TVDD
CVDD
CVDD
TVDD
CVDD
DVDD
TVDD
CVDD
TVDD
CVDD
DVDD
TVDD
CVDD
3
CVDD
CVDD
DGND
DGND
DGND
VDD 6 1 VOUT DGND DGND
RESET RESET
103
102
101
100
103
102
101
100
128
104
128
104
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
HSW_N_RST RXA_ARC HSW_N_RST RXA_ARC
99
98
97
99
98
97
65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96
65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96
TP6 TP23
1
DGND
DGND
12S3_IN RXB_ARC 12S3_IN RXB_ARC
R245
TP7 TP24
22K
R22 12S2_IN RXC_ARC R126 12S2_IN RXC_ARC
TP8 TP25
3
12S1_IN RXD_ARC 12S1_IN RXD_ARC
+3.3H TP9 +3.3H TP26
4
12S0_IN 12S0_IN
5 GND DVDD DVDD DGND
HSW2
5
Vref R16 10K 10KX4 SCLK_IN CVDD
R119 10K
10KX4 SCLK_IN CVDD
HSW1
4.7K
R117
4.7K
6
6
R120
R12
R17 10K SPDIF_IN/OUT/LRCLK_IN 10K SPDIF_IN/OUT/LRCLK_IN +5.5V +5H
RXD_2+ RXD_2+
7
Current Limit
TP64
HSW2_N_INT INT1 RXD_2- HSW1_N_INT INT1 RXD_2- 5.0
8
Thermal Shutdown HSW2_27MHZ T P 3 2C L K _ I N
HDMI SWITCHER RXD_1+ HSW1_27MHZ T P 3 3C L K _ I N
HDMI SWITCHER
RXD_1+
J3
9
0
CE 3 2 GND R21 CEC RXD_1- R125 CEC RXD_1-
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10
RP130Q501D-TR-F
+3.3H +3.3H no_use +3.3H no_use
DVDDIO DVDDIO
VOUT
TVDD
HSW_N_CS=Low TVDD
VDD
HDMI_SDA R18 22 SDA HSW_N_CS=High RXD_0+ HDMI_SDA R121 22 SDA RXD_0+
I2C:0xB0
R222
4.7K
10/10
10/10
I2C:0xB0
C216
C218
HDMI_SCL R19 22 SCL IC2 RXD_0- HDMI_SCL R122 22 SCL IC1 RXD_0- 4 3
IC14
R15 CS ADV7630KSVZ CS ADV7630KSVZ
Pin No. Symbol Description Q19 RXD_C+ HSW_N_CS RXD_C+ 1 2
0
CE/CE
GND
DVDD RXD_C- DVDD RXD_C-
1 VOUT Output Pin
TXB_PVDD G CVDD +1.8HCPLL1 TXB_PVDD G CVDD
2, 5 GND Ground Pin +1.8HCPLL2
L5
C24
TXB_PLVDD_N L19 C111
C107
TXB_PLVDD_N
C28 C18 C21 C26 DVDD C 1 0 2C 1 0 5 C 1 0 9 DVDD
DGND DGND
3 CE Chip Enable Pin ("H" Active) DTC014EUBTL BKP1005HS680-T T P 3T5X V D D _ 3 V 3 SYS_3P3V BKP1005HS680-T BKP1005HS680-T TXVDD_3V3 SYS_3P3V BKP1005HS680-T DGND
DGND 10/10
0.1/10(BJ)
0.1/10(BJ)
10/10 L38 L40
1000P(B)
1000P(B)
4 NC No Connection TXB_PLVDD_Q TXB_PLVDD_Q
HSW_N_CS DGND
No replacement part available.
HPA_A IN7_A_HPD +3.3H DGND
No replacement part available. HPA_A IN3_A_HPD +3.3H
C184
C189
0.1/10(BJ) 0.1/10(BJ)
C108
C188
0.1/10(BJ) 0.01/16(B) 0.1/10(BJ) 0.01/16(B)
4
TXB_HPD RXA_5V IN7_A_5VPWR TXB_HPD RXA_5V IN3_A_5VPWR
6 VDD Input Pin +3.3H 1000P(B) 1000P(B)
R13 TX_AVDD +3.3H TX_AVDD

DGND
DGND
HPA_B IN6_B_HPD R118 HPA_B IN2_B_HPD
4.7K 4.7K
TXB_C- RXB_5V IN6_B_5VPWR TXB_C- RXB_5V IN2_B_5VPWR
TXB_C+ TXB_C+ NOTICE (model)
TX_AVDD 3.3V: 225mA
HPA_C IN5_C_HPD
TX_AVDD
3.3V: 225mA HPA_C IN1_C_HPD
J JAPAN
RXC_5V IN5_C_5VPWR RXC_5V IN1_C_5VPWR
TX_2+ TXB_0- 1.8V: 890mA HPA_D IN4_D_HPD TX_2+ TXB_0-
1.8V: 890mA HPA_D
U U.S.A
TP44 C CANADA
IC16: NCP380HMUAJAATBG TX_2- TXB_0+ RXD_5V IN4_D_5VPWR
TX_2- TXB_0+ RXD_5V FR_D_5VPWR
R GENERAL
0.1/10(BJ)
0.1/10(BJ)
TX_AVDD DVDDIO,TVDD:3.3V TX_AVDD DVDDIO,TVDD:3.3V
0.01/16(B)
0.01/16(B)
Fixed / Adjustable current-limiting TX_1+ TXB_1-
DVDD,PVDD,CVDD:1.8V
REG_1P8V
EP_CS
DGND TX_1+ TXB_1-
DVDD,PVDD,CVDD:1.8V
REG_1P8V
EP_CS
DGND
T CHINA
C148
C147
C66
K KOREA
C63
power-distribution switches TX_1- TXB_1+ EP_SCK TX_1- TXB_1+ EP_SCK
A AUSTRALIA
GND
/WP
/CS
GND
/WP
/CS
SO
SO
TX_0+ TXB_2- EP_MISO TX_0+ TXB_2- EP_MISO
DGND DGND B BRITISH
R181
4 3 2 1 4 3 2 1
R182
TX_0- TXB_2+ TX_0- TXB_2+
R79
EP_MOSI EP_MOSI
R80
Blocking control IC7 TXA(B) Main Map 0xFE[0]=1 IC8 G EUROPE
TX_AVDD TX_AVDD TX_0-/+,1-/+,2-/+
REG_3P3V 5 6 7 8 REG_3P3V 5 6 7 8 L SINGAPORE
0.1/10(BJ)
0.1/10(BJ)
BKP1005HS680-T
0.01/16(B)
SI
SI
0.01/16(B)
/HOLD
/HOLD
SCK
SCK
58
59
60
61
62
63
64
58
59
60
61
62
63
64
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
VCC
VCC
0.1/10(BJ)
BKP1005HS680-T L17 E SOUTH EUROPE
R179
3.9K
+3.3H
C142
C144
TXA_HEAC-
TXA_HPD_HEAC-
TXA_HEAC-
TXA_HPD_HEAC-
100
10/10
IN 6
C59
1 OUT
0.1/10(BJ)
3.9K
L3
C58
V TAIWAN
C101
DVDD
TXB_DDC_SDA
TXB_DDC_SCL
TXA_DDC_SDA
TXA_DDC_SCL
TXA_PVDD
TXA_PLVDD_N
TXVDD_3V3
TXA_PLVDD_Q
R_EXT
TX_AVDD
TXA_C-
TXA_C+
TX_AVDD
TXA_0-
TXA_0+
TX_AVDD
TXA_1-
TXA_1+
TXA_2-
TXA_2+
TX_AVDD
DDCD_SCL
DDCD_SDA
DDCC_SCL
DDCC_SDA
DDCB_SCL
DDCB_SDA
DDCA_SCL
DDCA_SDA
R77
DVDD
TXB_DDC_SDA
TXB_DDC_SCL
TXA_DDC_SDA
TXA_DDC_SCL
TXA_PVDD
TXA_PLVDD_N
T P 3 8T X V D D _ 3 V 3
TXA_PLVDD_Q
R_EXT
TX_AVDD
TXA_C-
TXA_C+
TX_AVDD
TXA_0-
TXA_0+
TX_AVDD
TXA_1-
TXA_1+
TXA_2-
TXA_2+
TX_AVDD
DDCD_SCL
DDCD_SDA
DDCC_SCL
DDCC_SDA
DDCB_SCL
DDCB_SDA
DDCA_SCL
DDCA_SDA
+3.3H
C99
100
10/10
R78 R180
C60 C145 F RUSSIAN
C16
C19
P LATIN AMERICA
DGND
no_use DGND DGND no_use DGND
DGND BLM21PG600SN1D S BRAZIL
DGND
25LC040A-I-ST( ) BLM21PG600SN1D 25LC040A-I-ST( )

+1.8HSW +1.8HSW
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
Current L15 L29 H THAI
1000P(B)
1000P(B)
ILIM 2 Gate Driver TP36
10/10
10/10
C153
C158
C164
C167
C170
C172
C176
Limiter
C76
C82
C86
C89
C92
C94
C96
)
1000P(B) 0.01/16(B)
+3.3H
B
+1.8HCPLL1
6 (
+3.3H 0.1/10(BJ) 0.1/10(BJ)
0.1/10(BJ) 0.1/10(BJ)
+1.8HCPLL2 1
no_use
TX_2+
TX_2-
TX_1+
TX_1-
TX_0+
TX_0-
TX_2+
TX_2-
TX_1+
TX_1-
TX_0+
TX_0-
DGND
DGND
R62
22
22
22
22
IN4_D_SCL
IN4_D_SDA
IN5_C_SCL
IN5_C_SDA
IN6_B_SCL
IN6_B_SDA
IN7_A_SCL
IN7_A_SDA
IN1_C_SCL
IN1_C_SDA
IN2_B_SCL
IN2_B_SDA
IN3_A_SCL
IN3_A_SDA
C133 C131
R165
22
22
R146 22
R152 22
/
no_use
C31
R183
4.7K
TP34
1
R163
0
R54
VOUT
BLM21PG600SN1D
470
470
.
R145
R150
C132
TP31
RP130Q181D-TR-F
VDD
R26
R27
R31
R33
C32
Vref +1.8HSW
0
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
UVLO
0.1/10(BJ)
0.1/10(BJ)
VOUT
Osc L16
RP130Q181D-TR-F
1000P(B)
VDD
DGND
R195
4.7K
C33
TSD
4.7K
DGND
R166
4.7K
1000P(B)
R63
10/10
10/10
to DIGITAL 5/10
C190
4 3
C72
C77
C83
C87
C90
C93
C95
C97
GND 5
10/10
C191
C134
C30 C34
IC18
10/10
C175
DGND
DGND
4 3 To 005.sht
Flag
10/10
C179
1 2 CEC
3 /FLAG IC10 (HDMI_Tx)
DGND
BLM21PG600SN1D +3.3M
C115
AVRL161A1R1NTB
CE/CE
GND
1 2
100 +1.8HSW
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
L30
CE/CE
GND
1000P(B)
10/10
10/10
+3.3H
BKP1005HS680-T
10/10
C151
C155
C159
C165
C168
C171
C173
C177
EN block Control logic
R227
BKP1005HS680-T
EN 4 +3.3H
10K
D22
and timer
L8
DGND
+1.8HCPLL1
IC1
UPA672T-T1-A
DGND
L22
0
HSW2B_DSDA
HSW2B_DSCL
HSW2A_DSDA
HSW2A_DSCL
HSW1B_DSDA
HSW1B_DSCL
DGND
+1.8HCPLL2
no_use
D 3 D 6
no_use
DGND
0
R247
IC2
R248
DGND
J7
100
5 2
Q13
J6
DGND
G G
S 4 S 1
to DIGITAL 4/10
HDMI_PON
+1.8HSW
R155 4.7K
4.7K R139
HDMI_PON
HSW1_27MHZ
+1.8HSW
+3.3H R156 4.7K HSW1_27MHZ

4.7K R140
+3.3H To 004.sht
HSW2_27MHZ (FPGA)
HSW2_27MHZ
+3.3H
R246
12K
IC17: TC7SET08FU
+3.3H
2 input AND gate
R235
22K
MHLVB_PON
R232
2.2K
R233
2.2K
R234
22K
R238
5 VCC
HSW2B_DSDA
HSW2B_DSCL
HSW1B_DSDA
HSW1B_DSCL
IN B 1 MHL_VBUS_PRT
HDMI_PON
BLM21PG600SN1D BLM21PG600SN1D
HSW2A_DSDA
HSW2A_DSCL
+1.8H +3.3H +1.8H 100
+1.8HRPLL +3.3H
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
+3.3H
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
L2 L13
1000P(B)
1000P(B)
HRX1_N_INT FHDMI_N_RST
10/10
10/10
6 IN A 2
0.1/10(BJ)
C10
C12
C62
C65
C68
C70
C75
C80
TP28 DV_SDA
C2
C4
C6
C8
IC5
R164
4.7K
2
VOUT
R220
C174
HRX_N_INT DV_SCL
RP130Q181D-TR-F
4 V+
VDD
1 IC5 3 5
DGND
DGND
68 FHDMI_N_INT
GND 3 4 OUT Y V-
10/10
TC7SH08FU HRX2_N_INT
C149
4 3 HDMI_PON
10/10
+3.3H BLM21PG600SN1D DGND DGND C163 +3.3H BLM21PG600SN1D DGND DGND HDMI_PON
DGND IC9 DGND
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
RXB_2+
RXB_2-
RXB_1+
RXB_1-
RXB_0+
RXB_0-
RXB_C+
RXA_1+
RXA_1-
RXA_C-
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
0.1/10(BJ)
RXB_2+
RXB_2-
RXB_1+
RXB_1-
RXB_0+
RXB_0-
RXB_C+
RXA_1+
RXA_1-
RXA_C-
L1 L12
RXB_C-
RXA_2+
RXA_2-
RXA_0+
RXA_0-
RXA_C+
RXB_C-
RXA_2+
RXA_2-
RXA_0+
RXA_0-
RXA_C+
1 2 DGND
1000P(B)
1000P(B)
HSW2_N_INT
CVDD
TVDD
TVDD
TVDD
CVDD
CVDD
TVDD
TVDD
TVDD
CVDD
10/10
10/10
CVDD
DVDD
CVDD
TVDD
TVDD
TVDD
CVDD
DVDD
CVDD
TVDD
TVDD
TVDD
HSW2_N_INT
C64
CE/CE
GND
A B Y
GND
GND
C11
C13
C61
C78
C84
C3
GND
GND
GND
GND
C67
C69
C73
C1
HSW1_N_INT
C5
C7
C9
NC
NC
NC
NC
HSW1_N_INT
L L L HSW_N_RST
+3.3H HSW_N_RST
DGND
DGND
NC 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 NC NC 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 NC
L H L 33 128 33 128 HSW_N_CS
DVDD NC IC3,4 DVDD NC HSW_N_CS
DGND
H L L HRX1_MT
R215
4.7K
34 127 34 127
R39 R127 0
R178
HRX_D[47] A47 RXA_5V 0 HRX_Z_D[47] A47 RXA_5V IC6
H H H +3.3H +3.3H to DIGITAL 6/10
0
35 126 35 126 2 R219 HAU_INT
R1 R89 TP14
HRX2(ZONE)
470P(B)
HRX_D[46] A46 HPA_A HRX1_MT HRX_Z_D[46] A46 HPA_A 4 +3.3H
1
R199
36 125 36 125 HDMI_SCL
C180
10K
R57 DDCA_SDA TP15
HRX_D[45] A45
HRX1(MAIN) DDCA_SDA 4.7K HRX_Z_D[45] A45 R225
R186
R190
HRX2_MT +3.3H HDMI_SDA
2.2K
2.2K
37 124 +3.3H 37 124
HRX_D[44] 33X4 A44 DDCA_SCL R58 4.7K HRX_Z_D[44] 33X4 A44 DDCA_SCL TP16 +3.3H 4.7K
38 123 38 123
A43 RXB_5V R41 0 A43 RXB_5V R128 0 DGND
HDMI_SCL
39 122 39 122 HDMI_SCL
TP3 R217 no_use TP17 R218 no_use +3.3H
C138
HRX_D[43] DVDDIO HPA_B HRX_Z_D[43] DVDDIO HPA_B HDMI_SDA
40 121 40 121 IC6 5 HDMI_SDA
HRX_D[42] R2 A42 DDCB_SDA R55 4.7K HRX_Z_D[42] R90 A42 DDCB_SDA 3
41 120 +3.3H 41 120 HRTX_N_RST
HRX_D[41] A41 DDCB_SCL R56 4.7K HRX_Z_D[41] A41 DDCB_SCL HRTX_N_RST
IC5: TC7SH08FU
HRX_D[40] 33X4 A40
42
HDMI RECEIVER 119
CEC R59
+3.3H
HRX_Z_D[40] 33X4 A40
42
HDMI RECEIVER 119
CEC R129 no_use +3.3H DGND
no_use
28.63636MHZ
28.63636MHZ
43 118 R52 C45 no_use 43 118 R142 C124 HRX_N_INT
HRX_D[39] A39 DVDD DGND HRX_Z_D[39] A39 DVDD DGND HRX_N_INT
0.1/10(BJ)
no_use
0.1/10(BJ)
no_use
R138
44 117 150 44 117 150
2
2
1
1
10P(CH) 10P(CH) HRX1_MT
2-input AND gate
1000P(B)
R3 A38 R91 A38

R43
XL1
XL2
1000P(B)
HRX_D[38] XTALN HRX_Z_D[38] XTALN HRX1_MT
45 116 45 116

Yamaha Rx-A3030 PDF

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Yamaha Rx-A3030 PDF

Uploaded by

Document Information

Original Title

Copyright

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Yamaha Rx-A3030 PDF

Uploaded by

Copyright:

AV RECEIVER

Copyright (c) Yamaha Corporation All rights reserved.

TO SERVICE PERSONNEL AC LEAKAGE

Components having special characteristics are marked and

WARNING: CHEMICAL CONTENT NOTICE!

About lead free solder /

RX-V3075 (T, A models)

RX-A3030 (R, S models)

RX-A3030 (B, G, F models)

REMOTE CONTROL PANEL

Inside of the remote control cover

Bass Crossover Frequency / Signal to Noise Ratio / (IHF)

Optical Jack, Coaxial Jack Support Frequencies / Harmonic Distortion / (1 kHz)

Video Signal Type / Antenna Input /

D video signal / D [J model] Standby Power Consumption (reference data) /

J model .................................................................. 76.0 to 90.0 MHz Network standby: ON

x.v.Color is a trademark of Sony Corporation.

Android is a trademark of Google Inc.

50 335 (13-1/4") 50 335 (13-1/4")

Front view Front view

435 (17-1/8") 435 (17-1/8")

Unit: mm (inch) Unit: mm (inch)

Surround Back Initial Delay: 1 to 49 ms

Surround Back Room Size: 0.1 to 2.0

Surround Back Liveness: 0 to 10

Front/Rear Balance: -5 to +5, [0]

Surround Room Size: 0.1 to 2.0

Left/Right Balance: -5 to +5, [0]

Monaural Mix: Off / On, [Off]

Reverb Delay: 0 to 250 ms

Reverb Level: 0 to 100 %

Direct: Auto / Off, [Auto]

Level: -5 to +5, [0]

*1 Surround Decoder Panorama Center Width Dimension Center Image

SET MENU TABLE /

MAIN MENU SUB-MENU PARAMETER VALUE [INITIAL VALUE]

Setup Multi Position Yes / No

Result Not Available

Manual Setting Pattern [Pattern1] / Pattern2 * Select ENTER

Setting Data Copy Pattern1 2 / Pattern2 1 * Select ENTER

9ch +RP / 9ch +FRONT / 7ch +FP +RP /

7ch +FRONT +1ZONE / 5ch +FRONT +2ZONE / 7ch BI-AMP /

7ch BI-AMP +1ZONE / 7ch BI-AMP +FP +RP

EXTRA SP 1 / 2 Zone 2 / Zone 3

* When Power Amp Assign is set to Basic / 9ch +RP / 9ch

Configuration Front Large / [Small]

* When Subwoofer1/2 is set to None, Front is disabled.

Surround Back Large x1 / Large x2 / Small x1 / [Small x2] / None

* When Surround is set to None, Surround Back is disabled.

Crossover 40 / 60 / [80] / 90 / 100 / 110 / 120 / 160 / 200 Hz

* When Front / Center / Surround / Surround Back is set to

Front Presence [Use] / None

Rear Presence Use / [None]

Subwoofer 1, Subwoofer 2 [Use] / None

Select Use [Normal] / Reverse

SWFR Layout Left + Right / Front + Rear / [Monaural x2]

* When Subwoofer1/2 is set to None, SWFR Layout is disabled.

Extra Bass [Off] / On

* When Front is set to Large, Extra Bass is disabled.

Distance Meter / Feet

Rear Presence L, Rear Presence R,