Rrus Huawei

RRU3262 (700M)
Hardware Description
Issue 01
Date 2015-12-30
HUAWEI TECHNOLOGIES CO., LTD.

Copyright Huawei Technologies Co., Ltd. 2015. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior written
consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: support@huawei.com
Issue 01 (2015-12-30) Huawei Proprietary and Confidential i

Copyright Huawei Technologies Co., Ltd.
RRU3262 (700M)
Hardware Description About This Document
About This Document
Purpose
This document provides reference for planning and deploying an RRU3262(700M) (referred
to as RRU in this document). It presents the exterior and describes the ports, functions, cable
types, connector specifications, and cable connections of the RRU.
Product Versions
The following table lists the product versions related to the RRU3262(700M).
Product Name Solution Version Product Version
DBS3900 l SRAN9.0 and later V100R009C00 and later

versions versions
l eRAN7.0 and later
versions
Intended Audience
This document is intended for:
l Base station installation engineers
l System engineers
l Site maintenance engineers
Organization
1 Changes in RRU3262(700M) Hardware Description
This section describes the changes in RRU3262(700M) Hardware Description.
2 RRU Introduction
This chapter describes the exterior and function of the RRU as well as the ports and indicators
on the RRU.
Issue 01 (2015-12-30) Huawei Proprietary and Confidential ii

RRU3262 (700M)
3 RRU Cables
This chapter describes RRU cables.
4 RF Cable Connections for the RRU3262(700M)
RF cable connections for the RRU vary depending on the configurations of the RRU and
antenna.
5 RRU Auxiliary Devices
This chapter describes RRU auxiliary devices.
Conventions
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol Description
Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not

avoided, could result in death or serious injury.

avoided, may result in minor or moderate injury.

avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to personal
injury.
Calls attention to important information, best practices and

tips.
NOTE is used to address information not related to
personal injury, equipment damage, and environment
deterioration.
General Conventions
The general conventions that may be found in this document are defined as follows.
Convention Description
Times New Roman Normal paragraphs are in Times New Roman.
Boldface Names of files, directories, folders, and users are in

boldface. For example, log in as user root.
Issue 01 (2015-12-30) Huawei Proprietary and Confidential iii

RRU3262 (700M)
Italic Book titles are in italics.

Courier New Examples of information displayed on the screen are in
Courier New.
Command Conventions
The command conventions that may be found in this document are defined as follows.
Boldface The keywords of a command line are in boldface.
Italic Command arguments are in italics.
[] Items (keywords or arguments) in brackets [ ] are optional.
{ x | y | ... } Optional items are grouped in braces and separated by

vertical bars. One item is selected.
[ x | y | ... ] Optional items are grouped in brackets and separated by

vertical bars. One item is selected or no item is selected.
{ x | y | ... }* Optional items are grouped in braces and separated by

vertical bars. A minimum of one item or a maximum of all
items can be selected.
[ x | y | ... ]* Optional items are grouped in brackets and separated by

vertical bars. Several items or no item can be selected.
GUI Conventions
The GUI conventions that may be found in this document are defined as follows.
Boldface Buttons, menus, parameters, tabs, window, and dialog titles

are in boldface. For example, click OK.
> Multi-level menus are in boldface and separated by the ">"

signs. For example, choose File > Create > Folder.
Keyboard Operations
The keyboard operations that may be found in this document are defined as follows.
Issue 01 (2015-12-30) Huawei Proprietary and Confidential iv

RRU3262 (700M)
Format Description
Key Press the key. For example, press Enter and press Tab.
Key 1+Key 2 Press the keys concurrently. For example, pressing Ctrl
+Alt+A means the three keys should be pressed
concurrently.
Key 1, Key 2 Press the keys in turn. For example, pressing Alt, A means
the two keys should be pressed in turn.
Mouse Operations
The mouse operations that may be found in this document are defined as follows.
Action Description
Click Select and release the primary mouse button without

moving the pointer.
Double-click Press the primary mouse button twice continuously and

quickly without moving the pointer.
Drag Press and hold the primary mouse button and move the
pointer to a certain position.
Issue 01 (2015-12-30) Huawei Proprietary and Confidential v

RRU3262 (700M)
Hardware Description Contents
Contents
About This Document.....................................................................................................................ii

1 Changes in RRU3262(700M) Hardware Description.............................................................. 1
2 RRU Introduction.......................................................................................................................... 2
2.1 RRU Exterior.................................................................................................................................................................. 3
2.2 RRU Functions............................................................................................................................................................... 4
2.3 RRU Technical Specifications........................................................................................................................................5
2.4 RRU Ports.......................................................................................................................................................................5
2.5 RRU Indicators............................................................................................................................................................... 7
2.6 Optical Module............................................................................................................................................................... 9
3 RRU Cables...................................................................................................................................11
3.1 RRU Cables.................................................................................................................................................................. 13
3.2 RRU PGND Cable........................................................................................................................................................13
3.3 RRU Power Cable........................................................................................................................................................ 14
3.4 RRU Alarm Cable........................................................................................................................................................ 15
3.5 CPRI Fiber Optic Cable................................................................................................................................................17
3.6 RRU RF Jumper........................................................................................................................................................... 21
3.7 RRU AISG Multi-Wire Cable...................................................................................................................................... 22
3.8 RRU AISG Extension Cable........................................................................................................................................ 23
4 RF Cable Connections for the RRU3262(700M).....................................................................25

5 RRU Auxiliary Devices.............................................................................................................. 27
Issue 01 (2015-12-30) Huawei Proprietary and Confidential vi

RRU3262 (700M)
Hardware Description 1 Changes in RRU3262(700M) Hardware Description
1 Changes in RRU3262(700M) Hardware

Description
This section describes the changes in RRU3262(700M) Hardware Description.
01 (2015-12-30)
This is the first official release.
Compared with issue Draft A (2015-01-30), this issue does not include any new information.
Compared with issue Draft A (2015-01-30), this issue includes the following changes:
Topic Change Description
3.3 RRU Power Cable Added the outer diameter of RRU power
cables.
5 RRU Auxiliary Devices Modified the information of RRU auxiliary

devices.
Compared with issue Draft A (2015-01-30), no information is deleted from this issue.
Draft A (2015-01-30)
This is a draft.
Issue 01 (2015-12-30) Huawei Proprietary and Confidential 1

RRU3262 (700M)
Hardware Description 2 RRU Introduction
2 RRU Introduction
About This Chapter
This chapter describes the exterior and function of the RRU as well as the ports and indicators
on the RRU.
2.1 RRU Exterior

This section describes the exterior and dimensions of an RRU.
2.2 RRU Functions
This section describes main functions of an RRU.
2.3 RRU Technical Specifications
This section describes technical specifications of an RRU, including supported modes,
frequency bands, RF specifications, engineering specifications, and antenna capabilities.
2.4 RRU Ports
This section describes ports on the RRU panels. An RRU has a bottom panel, cabling cavity
panel, and indicator panel.
2.5 RRU Indicators
This section describes six indicators on an RRU. They indicate the running status of the RRU.
2.6 Optical Module
An optical module transmits optical signals between an optical port and a fiber optic cable.

RRU3262 (700M)
2.1 RRU Exterior

This section describes the exterior and dimensions of an RRU.
Figure 2-1 shows the exterior of an RRU.
Figure 2-1 RRU exterior
Figure 2-2 shows RRU dimensions.
Figure 2-2 RRU dimensions
You can obtain the RRU frequency band and power supply information from the
configuration label on the cover plate and obtain the RRU name from the nameplate on the
side of RRU that accommodates the conversion bracket. Figure 2-3 shows the positions of the
configuration label and nameplate on the RRU.

RRU3262 (700M)
NOTE
The actual label and nameplate may differ from what is shown in the figure.
Figure 2-3 Positions of the label and nameplate
(1) Configuration label (2) Nameplate (3) Frequency band
(4) Power supply type (5) Module name -
2.2 RRU Functions

This section describes main functions of an RRU.
The Remote Radio Unit (RRU) consists of the high-speed interface unit, signal processing
unit, power amplifier, duplexer, extension ports, and power module.
Figure 2-4 shows the functional structure of the RRU.
Figure 2-4 Functional structure of an RRU

RRU3262 (700M)
NOTE
For details about the extension ports, see 2.4 RRU Ports.
The RRU performs the following functions:

l Receives downlink baseband data from the BBU and sends uplink baseband data to the
BBU.
l Receives RF signals from the antenna system, down-converts the signals to intermediate
frequency (IF) signals, amplifies the IF signals, performs analog-to-digital conversion,
and up-converts RF signals to the transmit (TX) band.
l Multiplexes receive (RX) and TX signals on the RF channel so that these signals can
share the same antenna channel, and filters the RX and TX signals.
l Provides a built-in Bias Tee (BT). Besides receiving and transmiting RF signals, RRU
RF ports A and B transmit coupled RF signals and OOK signals to antennas through the
built-in BT. The RF ports A and B also supply DC power to the tower mounted amplifier
(TMA).
l The RRU can be powered by the AC/DC power module. In this case, this RRU is called
AC RRU. For details about the AC/DC power module, see AC/DC Power Module User
Guide or OPM15M User Guide or OPM50M User Guide.
2.3 RRU Technical Specifications

This section describes technical specifications of an RRU, including supported modes,
frequency bands, RF specifications, engineering specifications, and antenna capabilities.
For details about technical specifications of an RRU, see section Technical Specifications of
RRUs in the 3900 Series Base Station Technical Description.
2.4 RRU Ports

This section describes ports on the RRU panels. An RRU has a bottom panel, cabling cavity
panel, and indicator panel.
Figure 2-5 shows the ports on the RRU panels.

RRU3262 (700M)
Figure 2-5 Ports on the RRU panels
Table 2-1 describes ports and indicators on the RRU panels.
Table 2-1 Ports and indicators on the RRU panels

Item Silkscreen Remarks
(1) Bottom ports ANT_TX/RXA TX/RX port A, supporting RET signal

transmission
ANT_TX/RXB TX/RX port B, supporting RET signal

transmission
ANT_RXC TX/RX port C
ANT_RXD TX/RX port D
EXT_ALM Alarm monitoring port used for monitoring

one RS485 signal and two dry contact
signals

RRU3262 (700M)
Item Silkscreen Remarks
RET Communication port for the RET antenna,

supporting RET signal transmission
(2) Ports in the RTN(+) Power supply socket, for details about RRU
cabling cavity power cable experience and specifications,
NEG(-) see 3.3 RRU Power Cable.
CPRI0 Optical/electrical port 0, connected to the

BBU
CPRI1 Optical/electrical port 1, connected to the

BBU
(3) Indicator RUN For details, see 2.5 RRU Indicators.
ALM
ACT
VSWR
CPRI0
CPRI1
NOTE
l The port for transmitting RET signals is determined by the software.

l Connect the CPRI0 port to the BBU by default in the single-mode scenario.
2.5 RRU Indicators

This section describes six indicators on an RRU. They indicate the running status of the RRU.
For detailed positions of RRU indicators, see 2.4 RRU Ports.
Table 2-2 describes RRU indicators.
Table 2-2 RRU Indicators

Indicator Color Status Meaning
RUN Green Steady on The power input is available, but the board
is faulty.
Steady off No power input is available or the board is

faulty.
Blinking (on for The board is running properly.

1s and off for 1s)

RRU3262 (700M)
Blinking (on for The board software is being loaded or the

0.125s and off for board is not working.
0.125s)
ALM Red Steady on Alarms are generated, and the module must
be replaced.
Blinking (on for Alarms are generated. The alarms may be

1s and off for 1s) caused by faults on the related board or
ports. Therefore, you need to locate the
fault before deciding whether to replace the
module.
Steady off No alarms are generated.
ACT Green Steady on The board is working properly when TX

channels are enabled or software is being
loaded to a board that is not started.
Blinking (on for The board is running with TX channels

1s and off for 1s) disabled.
VSWR Red Steady off No voltage standing wave ratio (VSWR)

alarm is generated.
Blinking (on for VSWR alarms are generated on the

1s and off for 1s) ANT_TX/RXB port.
Steady on VSWR alarms are generated on the

ANT_TX/RXA port.
Blinking (on for VSWR alarms are generated on the

0.125s and off for ANT_TX/RXA and ANT_TX/RXB ports.
0.125s)
CPRI0 Red and Steady green The CPRI link is running properly.
green
Steady red An optical module fails to receive or
transmit signals possibly because the
optical module is faulty or the optical fiber
is broken.
Blinking red (on The CPRI link is out of lock because of

for 1s and off for faults on the mutual lock of dual-mode
1s) clock sources or mismatched data rates on
CPRI ports.
Steady off The optical module cannot be detected or is

powered off.
CPRI1 Red and Steady green The CPRI link is running properly.
green

RRU3262 (700M)
Steady red An optical module fails to receive or

transmit signals possibly because the
optical module is faulty or the optical fiber
is broken.
Blinking red (on The CPRI link is out of lock because of

for 1s and off for faults on the mutual lock of dual-mode
1s) clock sources or mismatched data rates on
CPRI ports.
Steady off The optical module cannot be detected or is

powered off.
NOTE
VSWR indicators on RRUs providing one or more than two TX channels have two types of status:
l Steady off: No VSWR alarm is generated.
l Steady on: VSWR alarms are generated on one or more ports.
2.6 Optical Module

An optical module transmits optical signals between an optical port and a fiber optic cable.
NOTE
l The exteriors of an optical module and the label on an optical module in this section are for
reference only. The actual exteriors may be different.
l Boards or RF modules supporting only the 1.25 Gbit/s CPRI port rate, for example, the GTMU or
RRU3908 V1, cannot use optical modules supporting a 9.8 Gbit/s CPRI port rate.
l Huawei wireless equipment can only use optical modules that have been certified by Huawei
Wireless Product Line. These optical modules must comply with the following standards and
requirements:
l Specifications required by products in specific application scenarios
l Laser safety standards of IEC 60825-1
l General safety requirements of IEC 60950-1
l For the codes of SFP and QSFP optical modules that have been certified by Huawei Wireless
Product Line, see Spare Parts Catalog.
Exterior
The following figure shows the exterior of an optical module.

RRU3262 (700M)
Figure 2-6 Exterior of an optical module
a: Optical module b: Bidirectional optical module
Label on an Optical Module

There is a label on each optical module, which provides information such as the rate,
wavelength, and transmission mode, as shown in the following figure.
Figure 2-7 Label on an optical module
(1) Rate (2) Wavelength (3) Transmission mode
Optical Module Type

Optical modules can be divided into single- and multimode optical modules, which can be
distinguished as follows:
l The puller of a single-mode optical module is blue and the puller of a multimode optical
module is black or gray.
l The transmission mode is displayed as "SM" on the label of a single-mode optical
module and "MM" on the label of a multimode optical module.

RRU3262 (700M)
Hardware Description 3 RRU Cables
3 RRU Cables
About This Chapter
This chapter describes RRU cables.
3.1 RRU Cables

This section describes RRU cable connections.
3.2 RRU PGND Cable
An RRU PGND cable connects an RRU and a ground bar, ensuring the proper grounding of
the RRU. The maximum length of an RRU PGND cable is 8 m (26.25 ft).
3.3 RRU Power Cable
The RRU power cable is a -48 V DC shielded cable. It feeds -48 V DC power to an RRU. The
length of power supply that an RRU power cable supports is 100 m (328.08 ft) by default.
3.4 RRU Alarm Cable
The RRU alarm cable, a shielded straight-through cable, transmits alarm signals from an
external device to an RRU so that the base station monitors the operating status of external
devices. The RRU alarm cable is 5 m (16.4 ft).
3.5 CPRI Fiber Optic Cable
CPRI fiber optic cables are classified into multimode fiber optic cables and single-mode fiber
optic cables. They transfer CPRI signals.
3.6 RRU RF Jumper
The 1/2" RRU RF jumper transmits and receives RF signals between an RRU and an antenna.
A fixed-length RF jumper used by an RRU is 2 m (6.56 ft), 3 m (9.84 ft), 4 m (13.12 ft), 6 m
(19.68 ft), or 10 m (32.81 ft). A variable-length RF jumper used by an RRU has a maximum
length of 10 m (32.81 ft).
3.7 RRU AISG Multi-Wire Cable
An RRU AISG multi-wire cable connects an RRU and an RCU to transmit control signals
from a base station to an RET antenna. When the RRU is connected to the RET antenna, an
AISG multi-wire cable transmits RS485 signals. The length of the AISG multi-wire cable is 5
m (16.40 ft).
3.8 RRU AISG Extension Cable
When the distance between an RRU and an RCU is longer than 5 m (16.4 ft), an AISG multi-
wire cable is not long enough to connect the RRU and the RCU. In this case, an AISG

RRU3262 (700M)
extension cable is used to extend the AISG multi-wire cable for transmitting RS485 signals.
The length of the AISG extension cable is 15 m (49.21 ft).

RRU3262 (700M)
3.1 RRU Cables

This section describes RRU cable connections.
Table 3-1 lists RRU cables.
Table 3-1 RRU cables
Cable One End The Other End
Connector Installation Connector Installation

Position Position
3.2 RRU OT terminal Ground OT terminal Ground terminal

PGND Cable (M6, 16 mm2 or terminal on (M8, 16 mm2 or on the ground
0.025 in.2) the RRU 0.025 in.2) bar
3.3 RRU Power Tool-less female NEG(-) and Depending on External power
Cable connector RTN(+) ports the power equipment
(pressfit type) on the RRU supply
equipment
3.4 RRU DB15 male EXT_ALM Cord end External alarm

Alarm Cable connector port on the terminal device
RRU
3.5 CPRI Fiber DLC connector CPRI0 port on DLC connector CPRI port on a
Optic Cable the RRU board in the
BBU
3.6 RRU RF DIN male RF ports on DIN male Antenna system

Jumper connector the RRU connector
3.7 RRU AISG DB9 waterproof RET port on Standard AISG Standard AISG
Multi-Wire male connector the RRU female male connector
Cable connector on the RCU or
on the AISG
extension cable
3.8 RRU AISG Standard AISG Standard Standard AISG Standard AISG
Extension male connector AISG female female male connector
Cable connector on connector on the RCU
the AISG
multi-wire
cable
3.2 RRU PGND Cable

An RRU PGND cable connects an RRU and a ground bar, ensuring the proper grounding of
the RRU. The maximum length of an RRU PGND cable is 8 m (26.25 ft).

RRU3262 (700M)
Exterior
A PGND cable is green or green and yellow with a cross-sectional area of 16 mm2 (0.025 in.
2). An OT terminal is installed at each end of the cable. Figure 3-1 shows a PGND cable.
Figure 3-1 PGND cable
(1) OT terminal (M6, 16 mm2 or 0.025 in.2) (2) OT terminal (M8, 16 mm2 or 0.025 in.2)
NOTE
l If the customer prepares the PGND cable, a copper-core cable with a cross-sectional area of 16 mm2
(0.025 in.2) or larger is recommended.
l One OT terminal must be added to each end of the PGND cable onsite.
l You can determine the color of the cable and whether to use corresponding two-hole OT terminals
based on local regulations.
Figure 3-2 shows a two-hole OT terminal.
Figure 3-2 Two-hole OT terminal
3.3 RRU Power Cable

The RRU power cable is a -48 V DC shielded cable. It feeds -48 V DC power to an RRU. The
length of power supply that an RRU power cable supports is 100 m (328.08 ft) by default.
NOTE
l The maximum length of power supply that an RRU power cable supports is 150 m (492.12 ft).
Contact Huawei engineers when an RRU power cable greater than 100 m (328.08 ft) is required.
l If a power device provided by the customer is used, the recommended specification of the circuit
breaker on this power device is 15 A to 30 A.
Exterior
A tool-less female connector (pressfit type) needs to be added to one end of the RRU power
cable and a corresponding terminal needs to be added to the other end based on the
requirements of the connector on the external power device, as shown in Figure 3-3.

RRU3262 (700M)
Figure 3-3 RRU power cable
(1) -48 V DC power cable (2) Shield layer (3) Tool-less female connector
(pressfit type)
The outer diameter of RRU power cables ranges from 9.9 mm to 14.4 mm, and Table 3-2 lists
the specifications of an RRU power cable.
Table 3-2 Specifications of an RRU power cable

RRU Type National Remote Cross-Sectional OCB Quantity
Standard Distance Area of the
Cable
RRU3262(7 European 0m to 70m 4mm2 0

00M) standard
71m to 100m 6mm2 0
American 0m to 70m 3.3mm2 0

standard
71m to 100m 5.3mm2 0
Table 3-3 lists the wire Colors of an RRU power cable.
Table 3-3 Wire Colors of an RRU power cable

Cable Wire Wire Color in Most Wire Color in Other Regions
Regions
North Europea UK
American n
Standard Standar
d
RRU RTN(+) Black Brown Blue

power
cable NEG(-) Blue Blue Gray
3.4 RRU Alarm Cable

The RRU alarm cable, a shielded straight-through cable, transmits alarm signals from an
external device to an RRU so that the base station monitors the operating status of external
devices. The RRU alarm cable is 5 m (16.4 ft).

RRU3262 (700M)
Exterior
An alarm cable has a DB15 waterproof male connector at one end and eight cord end
terminals at the other end, as shown in Figure 3-4.
Figure 3-4 Alarm cable
(1) DB15 waterproof male connector (2) Cord end terminal
Pin Assignment
Table 3-4 describes the pin assignment for the wires of an RRU alarm cable.
Table 3-4 Pin assignment for the wires of an RRU alarm cable
RRU Pin of the Color Type Cord End Description

Alarm Waterpro Terminal
Port ofed
DB15
Male
Connecto
r
Dry X1.2 White and Twisted X2 SWITCH_INPUT0+

contact blue pair
X1.3 Blue X3 SWITCH_INPUT0-

(GND)
X1.6 White and Twisted X4 SWITCH_INPUT1+

orange pair
X1.7 Orange X5 SWITCH_INPUT1-

(GND)
RS485 X1.10 White and Twisted X6 APM RX-

green pair
X1.11 Green X7 APM RX+
X1.13 White and Twisted X8 APM TX-

brown pair

RRU3262 (700M)
RRU Pin of the Color Type Cord End Description

Alarm Waterpro Terminal
Port ofed
DB15
Male
Connecto
r
X1.14 Brown X9 APM TX+
3.5 CPRI Fiber Optic Cable

CPRI fiber optic cables are classified into multimode fiber optic cables and single-mode fiber
optic cables. They transfer CPRI signals.
A multimode fiber optic cable connects a BBU to an RRU or connects two RRUs. The
maximum length of the multimode fiber optic cable between a BBU and an RRU is 150 m
(492.12 ft), and the multimode fiber optic cable between two RRUs has a fixed length of 10 m
(32.81 ft).
The single-mode fiber optic cable can be divided into two types: single-mode fiber optic cable
connecting a BBU to an RRU or connecting two RRUs (shortened to directly connected
single-mode fiber optic cable) and single-mode fiber optic cable connecting an ODF to a BBU
or RRU (shortened to single-mode pigtail). The maximum length of the single-mode pigtail
between an ODF and a BBU is 20 m (65.62 ft). The maximum length of the single-mode
pigtail between an ODF and an RRU is 70 m (229.66 ft).
NOTE
l The ODF is an outdoor transfer box for fiber optic cables, which interconnects the single-mode
pigtail and trunk single-mode fiber optic cable.
l The ODF and trunk single-mode fiber optic cable are provided by the customer and must comply
with the ITU-T G.652 standard.
l A multimode fiber optic cable is used together with a multimode optical module, and a single-mode
pigtail is used together with a single-mode optical module.
Selection Principle
The following table describes the principles for selecting CPRI fiber optic cables.
Table 3-5 Principles for selecting CPRI fiber optic cables
Remote CPRI Data Selection Principle Remarks

Distance Rate of the
Optical
Module
(Gbit/s)
100 m 2.5 or 4.9 Multimode fiber optic Connects a BBU to an RRU.

(328.08 cable When it connects two RRUs, the
ft) distance between the two RRUs

RRU3262 (700M)
Remote CPRI Data Selection Principle Remarks

Distance Rate of the
Optical
Module
(Gbit/s)
9.8 Directly connected must be less than or equal to 10 m

single-mode fiber optic (32.81 ft).
cable
100 m 2.5 or 4.9 Multimode fiber optic Connects a BBU to an RRU.

(328.08 cable
ft) <
Remote 9.8 Directly connected
distance single-mode fiber optic
150 m cable
(492.13 - Recommended: single- The single-mode pigtail at the RRU
ft) mode fiber optic cable or BBU side is connected to the
(single-mode pigtail and trunk single-mode fiber optic cable
trunk single-mode fiber by using an ODF.
optic cable)
> 150 m - Single-mode fiber optic

(82.02 ft) cable (single-mode
pigtail and trunk single-
mode fiber optic cable)
Exterior
Multimode fiber optic cable or directly connected single-mode fiber optic cable: The
cable has a DLC connector at each end, as shown in the following figure.
Figure 3-5 Multimode fiber optic cable or directly connected single-mode fiber optic cable
(1) DLC connector (2) Breakout cable (3) Label on the breakout cable
NOTE
l When a BBU and an RRU are connected, the breakout cable on the BBU side is 0.34 m (1.12 ft)
long, and the breakout cable on the RRU side is 0.03 m (0.098 ft) long.
l When two RRUs are connected, the breakout cables on both sides are 0.03 m (0.098 ft) long.
The following figure shows the connection of the multimode fiber optic cable or directly
connected single-mode fiber optic cable between a BBU and an RRU as an example.

RRU3262 (700M)
Figure 3-6 Connection of the multimode fiber optic cable or directly connected single-mode
fiber optic cable between a BBU and an RRU
(1) Multimode fiber optic cable or directly connected single-mode fiber optic cable between a BBU and an
RRU
OFD06 trunk fiber optic cable: The OFD06 trunk fiber optic cable connects a BBU to an
OFD06 and has 12 LC connectors at each end, as shown in the following figure.
Figure 3-7 OFD06 trunk fiber optic cable
(1) LC connector (2) Breakout cable (3) Label on the breakout cable
Single-mode pigtail: The single-mode pigtail has a DLC connector at one end and an FC,
LC, or SC connector at the other end, as shown in the following figure.

RRU3262 (700M)
Figure 3-8 Exterior of a single-mode pigtail
(1) DLC (2) Breakout (3) Label on the (4) FC (5) LC (6) SC
connector cable breakout cable connector connector connector
NOTE
l When a single-mode pigtail connects a BBU to an ODF, the breakout cables on the BBU side and
ODF side are 0.34 m (1.12 ft) and 0.8 m (2.62 ft), respectively.
l When a single-mode pigtail connects an RRU to an ODF, the breakout cables on the BBU side and
ODF side are 0.03 m (0.098 ft ft) and 0.8 m (2.62 ft), respectively.
The following figure shows the connection of the single-mode pigtail.
Figure 3-9 Connection of the single-mode pigtail
(1) Single-mode pigtail between a BBU and an ODF (2) Single-mode pigtail between an RRU and an ODF

RRU3262 (700M)
Pin Assignment
The following table describes the labels on the breakout cables of a CPRI fiber optic cable
and recommended cable connections.
Table 3-6 Labels on the breakout cables of a CPRI fiber optic cable and recommended cable
connections
Label on the Installation Position
Breakout Cable
Connection Connection Connection
Between a BBU Between RRUs Between a BBU or
and an RRU or RRU and an ODF
Between an
OFD06 and an
RRU
1A CPRI RX port on the CPRI RX port on RX port on the BBU or

RRU RRU 1 CPRI RX port on the
RRU
1B CPRI TX port on the CPRI TX port on TX port on the BBU or

RRU RRU 1 CPRI TX port on the
RRU
2A OFD06 or TX port CPRI TX port on ODF

on the BBU RRU 0
2B OFD06 or RX port CPRI RX port on ODF

on the BBU RRU 0
3.6 RRU RF Jumper

The 1/2" RRU RF jumper transmits and receives RF signals between an RRU and an antenna.
A fixed-length RF jumper used by an RRU is 2 m (6.56 ft), 3 m (9.84 ft), 4 m (13.12 ft), 6 m
(19.68 ft), or 10 m (32.81 ft). A variable-length RF jumper used by an RRU has a maximum
length of 10 m (32.81 ft).
NOTE
l When the distance between an RRU and an antenna is less than 10 m (32.81 ft), one end of the RF jumper
is connected to an RF port at the bottom of the RRU, and the other end is connected to the antenna.
l When the distance between an RRU and an antenna is greater than 10 m (32.81 ft), one end of the RF
jumper is connected to a feeder, and the other end is connected to the antenna.
l If the customer prepares the RF jumper, the length of the RF jumper should be as short as possible and
not exceed 2 m (6.56 ft.).
Exterior
An RF jumper has a DIN male connector at one end and a customized connector at the other
end.
Figure 3-10 shows an RF jumper with a DIN male connector at each end.

RRU3262 (700M)
Figure 3-10 RF jumper
(1) DIN male connector
3.7 RRU AISG Multi-Wire Cable

An RRU AISG multi-wire cable connects an RRU and an RCU to transmit control signals
from a base station to an RET antenna. When the RRU is connected to the RET antenna, an
AISG multi-wire cable transmits RS485 signals. The length of the AISG multi-wire cable is 5
m (16.40 ft).
NOTE
An RCU is a driving motor used for the phase shifter in the RET antenna. It receives control commands from
a base station and runs the commands to drive the stepper motor. Using a gear, the stepper motor drives the
adjustable phase shifter in the antenna and changes the downtilt angle.
Exterior
An AISG multi-wire cable has a waterproofed DB9 male connector at one end and a standard
AISG female connector at the other end, as shown in Figure 3-11.
Figure 3-11 AISG multi-wire cable
(1) Waterproofed DB9 male connector (2) Standard AISG female connector
Pin Assignment
Table 3-7 describes the pin assignment for the wires of an AISG multi-wire cable.

RRU3262 (700M)
Table 3-7 Pin assignment for the wires of an AISG multi-wire cable
X1 End (Pin of X2 End (Pin of the Color Type Description

the Standard AISG
Waterproofed Female Connector)
DB9 Male
Connector)
White and
blue Twisted
X1.1 X2.1 +12 V
pair
Blue
X1.3 X2.3 White and RS485 B

orange Twisted
pair
X1.5 X2.5 Orange RS485 A
X1.4 X2.4 White and - GND

green
X1.9 and X1.4 are - - - GND

interconnected.
- X2.1 and X2.6 are - - +12 V

interconnected.
- X2.4 and X2.7 are - - GND

interconnected.
3.8 RRU AISG Extension Cable

When the distance between an RRU and an RCU is longer than 5 m (16.4 ft), an AISG multi-
wire cable is not long enough to connect the RRU and the RCU. In this case, an AISG
extension cable is used to extend the AISG multi-wire cable for transmitting RS485 signals.
The length of the AISG extension cable is 15 m (49.21 ft).
Exterior
An AISG multi-wire cable has a standard AISG male connector at one end and a standard
AISG female connector at the other end, as shown in Figure 3-12.
Figure 3-12 AISG extension cable
(1) Standard AISG male connector (2) Standard AISG female connector

RRU3262 (700M)
Pin Assignment
Table 3-8 describes the pin assignment for the wires of an AISG extension cable.
Table 3-8 Pin assignment for the wires of an AISG extension cable
X1 End (Pin X2 End (Pin Color Type Description
of the of the
Standard Standard
AISG Male AISG
Connector) Female
Connector)
X1.1 X2.1 White and blue Twisted pair +12 V
Blue
X1.7 X2.7 White and Twisted pair DC Return

orange
Orange
X1.3 X2.3 White and green Twisted pair RS485 B
X1.5 X2.5 Green RS485 A
X1.6 X2.6 White and brown Twisted pair +24 V
Brown

RRU3262 (700M)
Hardware Description 4 RF Cable Connections for the RRU3262(700M)
4 RF Cable Connections for the

RRU3262(700M)
RF cable connections for the RRU vary depending on the configurations of the RRU and
antenna.
Description of RF Cable Connections

This section describes the RF cable connections for the RRU serving a single sector. The
following table lists the RF cable connections for the RRU.
Table 4-1 RF cable connections for the RRU

RRU Model Specifications of a Scenario Illustration of
Single RRU Cable
Connections
RRU3262(700M) For details, see the 2T2R See illustration 1 in

typical power Figure 4-1.
configuration of the
corresponding RRU in 2T4R See illustration 2 in
"Technical Figure 4-1.
Specifications of
RRUs" of 3900 Series
Base Station Technical
Description.

RRU3262 (700M)
Hardware Description 4 RF Cable Connections for the RRU3262(700M)
Illustration of Cable Connections
Figure 4-1 RF cable connections for the RRU

RRU3262 (700M)
Hardware Description 5 RRU Auxiliary Devices
5 RRU Auxiliary Devices
This chapter describes RRU auxiliary devices.
Indoor Floor installation Support

An Indoor Floor installation Support (IFS06) is used for installing indoor RRUs.
For details about the exterior, specifications, and installation of an IFS06, see the 3900 Series
Base Station Hardware Description and DBS3900 (ICR) Installation Guide.
Outdoor Pole Support

OFP06, short for Outdoor Flexible Pole For 6, is an outdoor pole support and provides a
solution for extended installation of Huawei products on towers or building tops.
For details about the exterior and installation of an OFP06, see the OFP06 Installation Guide.
OCB
An Outdoor Cable Conversion Box (OCB) interconnects cables of different core diameters.
Power cables shipped with RRUs cannot support long-distance power supply. Therefore,
when power supply is far from the equipment, cables with large core diameters are used, and
an OCB connects these cables and RRU power cables.
For details about the structure, functions, installation, and maintenance of an OCB, see the
OCB User Guide or OCB01M User Guide.
Power Module
Power module is used to convert external AC input power into -48 V DC for the DC RRU,
including the following type:
l AC/DC Power Module
l OPM15M
l OPM30M
l OPM50M
For details about the structure, functions, installation, and maintenance of a Power Module,
see the AC/DC Power Module User Guide or OPM15M User Guide or OPM30M User Guide
or OPM50M User Guide.

RRU3262 (700M)
Hardware Description 5 RRU Auxiliary Devices
Distribution Equipment
The ODM03D is small distribution equipment, which supports RRU capacity expansion,
power cable reuse, and fiber optic cable reuse.
For details about the structure, functions, installation, and maintenance of an ODM03D, see
the ODM03D User Guide.


Rrus Huawei

Uploaded by

Copyright:

Available Formats

Rrus Huawei

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Rrus Huawei

Uploaded by

Copyright:

Available Formats

What are the different components described in the document?

What are the different components described in the document?

What are the different cable connections described for the RRU?

What are the different cable connections described for the RRU?

RRU3262 (700M)

HUAWEI TECHNOLOGIES CO., LTD.

Trademarks and Permissions

Huawei Technologies Co., Ltd.

Issue 01 (2015-12-30) Huawei Proprietary and Confidential i

About This Document

DBS3900 l SRAN9.0 and later V100R009C00 and later

Issue 01 (2015-12-30) Huawei Proprietary and Confidential ii

Indicates an imminently hazardous situation which, if not

Indicates a potentially hazardous situation which, if not

Indicates a potentially hazardous situation which, if not

Indicates a potentially hazardous situation which, if not

Calls attention to important information, best practices and

Times New Roman Normal paragraphs are in Times New Roman.

Boldface Names of files, directories, folders, and users are in

Issue 01 (2015-12-30) Huawei Proprietary and Confidential iii

Italic Book titles are in italics.

Boldface The keywords of a command line are in boldface.

Italic Command arguments are in italics.

[] Items (keywords or arguments) in brackets [ ] are optional.

{ x | y | ... } Optional items are grouped in braces and separated by

[ x | y | ... ] Optional items are grouped in brackets and separated by

{ x | y | ... }* Optional items are grouped in braces and separated by

[ x | y | ... ]* Optional items are grouped in brackets and separated by

Boldface Buttons, menus, parameters, tabs, window, and dialog titles

> Multi-level menus are in boldface and separated by the ">"

Issue 01 (2015-12-30) Huawei Proprietary and Confidential iv

Click Select and release the primary mouse button without

Double-click Press the primary mouse button twice continuously and

Issue 01 (2015-12-30) Huawei Proprietary and Confidential v

About This Document.....................................................................................................................ii

4 RF Cable Connections for the RRU3262(700M).....................................................................25

Issue 01 (2015-12-30) Huawei Proprietary and Confidential vi

1 Changes in RRU3262(700M) Hardware

This section describes the changes in RRU3262(700M) Hardware Description.

Topic Change Description

5 RRU Auxiliary Devices Modified the information of RRU auxiliary

Issue 01 (2015-12-30) Huawei Proprietary and Confidential 1

About This Chapter

2.1 RRU Exterior

Issue 01 (2015-12-30) Huawei Proprietary and Confidential 2

2.1 RRU Exterior

Figure 2-1 shows the exterior of an RRU.

Figure 2-1 RRU exterior

Figure 2-2 shows RRU dimensions.

Figure 2-2 RRU dimensions

Issue 01 (2015-12-30) Huawei Proprietary and Confidential 3

Figure 2-3 Positions of the label and nameplate

(1) Configuration label (2) Nameplate (3) Frequency band

(4) Power supply type (5) Module name -

2.2 RRU Functions

Figure 2-4 Functional structure of an RRU

Issue 01 (2015-12-30) Huawei Proprietary and Confidential 4

The RRU performs the following functions:

2.3 RRU Technical Specifications