L7-L18 Commissioning and Integration With FXED

L7/L18 commissioning and integration with FXED
7/25/2016 Work instruction For internal use Nokia 2016
1 / 55
Contents
1 Purpose ........................................................................................................................4
2 Prerequisites ................................................................................................................5
2.1 HW ................................................................................................................................5
2.1.1 HW for site build configurations ..................................................................................5
2.1.2 Additional HW for 3CC CA configuration .....................................................................8
2.2 SW ................................................................................................................................9
2.3 L7/L18 frequency allocation .......................................................................................10
2.4 XML Commissioning Files.............................................................................................10
3 L7/L18 connectivity diagram ......................................................................................11
4 L18 RF tails connections for distributed 2T4R configuration.....................................17
4.1 RF tails connections for distributed 2T4R L18 with 2 x FXED ....................................18
4.2 RF tails connections for distributed 2T4R L18 with 1 x FXED per sector ..................19
5 RF tails connections for 2T2R L7 configuration ..........................................................20
6 RF tails connections for 2T4R L7 configuration with 2xFRPA .....................................21
7 3CC CA FSMFs Interconnection Cable Installation ......................................................22
7.1 SRIO Cable Installation.................................................................................................22
7.2 HDMI Synchronisation Cable Installation.....................................................................23
8 Commissioning.............................................................................................................24
8.1 Power on FSMF and all RF modules .............................................................................24
8.2 Connect to site with BTS Site Manager .......................................................................24
8.3 SW upgrade from RL40 1.2 to RL60 1.1 (LN6.0_ENB_1311_764_08) ........................26
8.4 SW upgrade from RL60 1.1 to RL70 2.3.1 (LN7.0_ENB_1407_586_18) .....................27
8.5 Commissioning TRS only ..............................................................................................28
8.6 RF units detection........................................................................................................29
8.7 BTS Site commissioning steps.....................................................................................30
8.7.1 Introduction .................................................................................................................30
8.7.2 L18 MHA commissioning .............................................................................................32
2 / 55
8.7.3 L7 MHA commissioning................................................................................................32
8.7.3.1 L7 Antenna Line Management.....................................................................................33
8.7.3.2 L7 AISG MHA settings ..................................................................................................36
8.7.3.3 L7 AISG MHA settings ..................................................................................................39
8.7.4 Send Parameters .........................................................................................................44
8.7.5 Additional Site Settings................................................................................................44
8.7.6 Site Testing ..................................................................................................................45
8.7.7 Commissioning Report ................................................................................................47
8.8 Retrieve certificate ......................................................................................................48
8.9 Commissioning completed ..........................................................................................50
9 Check L7 & L18 Cell RSSI level .....................................................................................51
10 Test call ........................................................................................................................52
10.1 L18 testing ...................................................................................................................52
10.2 L7 testing .....................................................................................................................53
11 References ...................................................................................................................54
11.1 4G LTE bands ...............................................................................................................54
11.2 SFP modules used in L7/L18/L23/L26 eNB ...............................................................54
11.3 FSMF LMP connector pin map .....................................................................................55
3 / 55
1 Purpose
This document describes the work instructions of commissioning and integration of Nokia LTE
FDD LTE700/LTE1800 eNB with FXED.
Following configurations are covered:
Baseband: 1xFSMF + 1xFBBA + 1xFBBC or 1xFSMF + 1xFBBC + 1xFBBC
Radio:
- 3xFXED+1xFRPA L18 distributed 2T4R+L7 stacked 2T2R
- 3xFXED+3xFRPA Fully Distributed, L7 and L18 2T4R
- 2xFXED+1xFRPA L18 stacked 2T4R+L7 stacked 2T2R
- 3xFXED+2xFRPA L18 distributed 2T2R/2T4R+L7 stacked 2T4R
L7 1+1+1 @ 40W 10MHz bandwidth
L18 1+1+1 @ 60W 15MHz bandwidth
eNB software RL70 2.3.1
4 / 55
2 Prerequisites
Ensure that health and safety regulations are observed at any given time during the site build.
The weight of the RF unit is close to 25 kg. As such two man lift is recommended.
2.1 HW
HW requirement includes two parts.
- HW for site build configurations

- Additional HW for 3CC CA configuration
2.1.1 HW for site build configurations
The following main HW components are required for the different configurations.
All L7/L18 dual sites require 2xFBBC or 1xFBBA+1xFBBC, and the second BB
extension card has to be FBBC.
It is highly recommended to use only FSMF with 2xFBBC cards in greenfield
deployment.
Please ensure FRPA 1/2/3 are connected to ports RF1/2/4 respectively on
the second FBBC.
1. 3xFXED+1xFRPA L18 distributed 2T4R+L7 stacked 2T2R
HW component Quantity
FSMF 1
FBBC* 2
FPFD** 1
FRPA 1
FXED 3
FOSI*** 6 (FXED FSMF)
FOSH**** 2 (FRPA FSMF)
Single mode Optic
3 (FXED FSMF)
Fibre*****
Multi-mode Optic
1 (FRPA FSMF)
Fibre******
1000Base-T Ethernet
1
Cat6 cable
5 / 55
2. 3xFXED+3xFRPA Fully Distributed, L7 and L18 2T4R
FSMF 1
FBBC* 2
FPFD** 1
FRPA 3
FXED 3
Single mode Optic
3 (FXED FSMF)
Fibre*****
Multi-mode Optic
3 (FRPA FSMF)
Fibre******
1000Base-T Ethernet
1
Cat6 cable
3. 2xFXED+1xFRPA L18 stacked 2T4R+L7 stacked 2T2R
FSMF 1
FBBC* 2
FPFD** 1
FRPA 1
FXED 2
Single mode Optic
4 (FXED FSMF)
Fibre*****
Multi-mode Optic
1 (FRPA FSMF)
Fibre******
1000Base-T Ethernet
1
Cat6 cable

Note: this configuration should only be considered if antenna line does not support 4 way
Rx diversity on L18.
FSMF 1
FBBC* 2
6 / 55
FPFD** 1
FRPA 1
FXED 1
Single mode Optic
2 (FXED FSMF)
Fibre*****
Multi-mode Optic
1 (FRPA FSMF)
Fibre******
1000Base-T Ethernet
1
Cat6 cable
FSMF 1
FBBC* 2
FPFD** 1
FRPA 2
FXED 1
FOSH*** 8
Multi-mode Optic
4
Fibre***
1000Base-T Ethernet
1
Cat6 cable
FSMF 1
FBBC* 2
FPFD** 1
FRPA 2
FXED 4
12 (RF units to
FOSH***
FSMF/FBBx)
Multi-mode Optic 6 (RF units to
Fibre***** FSMF/FBBx)
1000Base-T Ethernet
1
Cat6 cable
7. 3xFXED+2xFRPA L18 distributed 2T2R/2T4R+L7 stacked 2T4R
7 / 55
FSMF 1
FBBC* 2
FPFD** 1
FRPA 2
FXED 3
Single mode Optic
3 (FXED FSMF)
Fibre*****
Multi-mode Optic
2 (FRPA FSMF)
Fibre******
1000Base-T Ethernet
1
Cat6 cable
* Optional use of FBBA+FBBC is allowed.
** FPFD is a preferred piece of equipment. If not available DC power for RF units needs to be
prepared independently. In partially stacked (L7) and partially distributed (L18) build FPFD would
provide power only to stacked L7 RF modules.
*** Note: Thepreferred build should be based on FOSI SFPs. If a FOSA or FOSG is already installed
and alternation to the existing L18 build is not possible Optus Project Manager needs to approve
build with SFPs other than FOSI. Note fibre check needs to also be run to match the SFP type with
the single mode or multi-mode fibre used on site.
**** Note: FOSI and SM links are also possible.

***** Note: IfFOSI (or FOSA) are used SM fibre is required. If FOSG are used MM fibre is needed
****** Note: MM fibre is preferred with FOSH. SM with FOSI is also possible
2.1.2 Additional HW for 3CC CA configuration
Below two cables need to be installed between collocated LTE FDD and LTE TDD sites in order to
enable Downlink Carrier Aggregation 3CC.
SRIO Link between collocated modules of paired FDD and TDD sites
HDMI cable between TDD Sync Out and FDD Sync In ports
Module / Item Name Description Qty

FBBC Nokia Flexi Baseband Extension 1
Module
8 / 55
FOSH Optical SFP H 850nm 6GBps 300m 2
Multi Mode
Multimode Fibre Note: Only one fibre cable required 1
Cable per site to be installed. Below is the
Nokia SRIO cable length option:
FSFO Flexi System Fibre HF 2m, MM See above note
FSFD Flexi System Fibre D 4m, MM See above note
FSFF Flexi System Fibre F 10m, MM See above note
FSFG Flexi System Fibre G 20m, MM See above note
HDMI Sync Cable Note: only one HDMI Sync cable 1
required to be installed between
1800 FSMF and 2300 FSMF. Below is
the Nokia HDMI cable length option
FTSF Sync Cable F, 2m HDMI to HDMI both See above note
with IP boot protection
FTSP Sync Cable F, 5m HDMI to HDMI both See above note
FTSQ Sync Cable F, 10m HDMI to HDMI both See above note
FTQR Sync Cable F, 15m HDMI to HDMI both See above note
FTSO Sync Cable O, 25m HDMI to HDMI See above note
both with IP boot protection
Please refer to Chapter 7 for 3CC Cabling.
2.2 SW
The final software RL70 2.3.1 will be used in L7/L18 dual band site with FXED.
New FSMF is delivered with preinstalled LN4.0 1.2 (LN4.0 ENB 1202_781_57) SW or FDSW 1.0
(boot-loader).
Upgrade paths:
RL40 1.2 (LN4.0_ENB_1202_781_57) RL60 1.1 (LN6.0_ENB_1311_764_08) RL70 2.3.1
(LN7.0_ENB_1407_586_18)
FDSW1.0_RP_FD1405_284_00 RL70 2.3.1 (LN7.0_ENB_1407_586_18)
Ensure all Software listed is available prior to Installation and Commissioning.
9 / 55
RL70 2.3.1
Software Software Version

Nokia FDD LTE BTS Software LN7.0_ENB_1407_586_18
Nokia FDD LTE BTS Element Manager LN7.0_BTSSM_1407_121_00
RL60 1.1
Software Software Version

Nokia FDD LTE BTS Software LN6.0_ENB_1311_764_08
Nokia FDD LTE BTS Element Manager LN6.0_BTSSM_1311_097_00
2.3 L7/L18 frequency allocation
Below table shows frequency allocation for Optus L7 and L18.
L7 EARFCN Frequency Bandwidth

Downlink 9260 763.0 MHz 10 MHz
Uplink 27260 708.0 MHz
L18 EARFCN Frequency Bandwidth

Downlink 1725 1857.5 MHz 15 MHz
Uplink 19725 1762.5 MHz
2.4 XML Commissioning Files
L7+L18 XML site commissioning template file will be distributed by Nokia RIC.
10 / 55
3 L7/L18 connectivity diagram
Please follow the below diagrams to connect optical fibres between RF modules and system module
according to site configuration.
1. Standard cabling for 3xFXED+1xFRPA L18 distributed 2T4R+L7 stacked 2T2R
Connect RF/EXT1 port on FSMF to Opt 1 port on FXED1 (Single Mode OBSAI link with FOSI SFPs)
Connect RF1 port on FBBC2 to Opt 1 port on FRPA (Multi Mode OBSAI link with FOSH SFPs)
Note: FRPA unit needs to be connected to the second FBBC.
Picture 1 - 3xFXED+1xFRPA L18 distributed 2T4R+L7 stacked 2T2R

2. Standard cabling for 3xFXED+3xFRPA Fully Distributed, L7 and L18 2T4R
11 / 55
Connect RF1 port on FBBC2 to Opt 1 port on FRPA1 (Multi Mode OBSAI link with FOSH SFPs)

Note: FBBC2 port3 should not be used to connect RRUs.
Picture 2 - 3xFXED+3xFRPA Fully Distributed, L7 and L18 2T4R
3. Standard cabling for 2xFXED+1xFRPA L18 stacked 2T4R+L7 stacked 2T2R

Connect RF3 port on FBBC1 to Opt 2 port on FXED2 (Single Mode OBSAI link with FOSI SFPs)
If FBBA is used instead of FBBC1: Connect RF port on FBBA to Opt 2 port on FXED2 (Single Mode OBSAI link
with FOSI SFPs)
Note: FRPA units need to be connected to the second FBBC.
12 / 55
Picture 3 - 2xFXED+1xFRPA L18 stacked 2T4R+L7 stacked 2T2R
4. Standard cabling for 1xFXED+1xFRPA L18 stacked 2T2R+L7 stacked 2T2R

Connect RF/EXT1 port on FSMF to Opt 1 port on FXED (Single Mode OBSAI link with FOSI SFPs)
Connect RF/EXT2 port on FSMF to Opt 2 port on FXED (Single Mode OBSAI link with FOSI SFPs)
13 / 55
Connect RF/EXT1 port on FSMF to Opt 1 port on FXED (Multi Mode OBSAI link with FOSH SFPs)
Connect RF/EXT2 port on FSMF to Opt 2 port on FXED (Mutli Mode OBSAI link with FOSH SFPs)
14 / 55

Connect RF/EXT1 port on FSMF to Opt 1 port on FXED1 (Multi Mode OBSAI link with FOSH SFPs)
Connect RF3 port on FBBC1 to Opt 2 port on FXED2 (Multi Mode OBSAI link with FOSH SFPs)
If instead of FBBC1 and FBBA is used: Connect RF1 of FBBA to OPT2 port on FXED2 (Multi M ode OBSAI link
with FOSH SFPs)
15 / 55
7. 3xFXED+2xFRPA L18 distributed 2T2R/2T4R+L7 stacked 2T4R

16 / 55
Picture 7 - 3xFXED+2xFRPA L18 distributed 2T2R/2T4R+L7 stacked 2T4R
4 L18 RF tails connections for distributed 2T4R

configuration
Some plumbing diagrams show 4R requirement for L18. In this scenario, 4 x RF tails are needed.
Please follow below instructions to connect 4 RF tails between FXEDs and Quad-band combiners.
For example:
17 / 55
4.1 RF tails connections for distributed 2T4R L18 with 2 x FXED
The below diagram illustrates tails connections for stacked L18 at Sector 1.
Sector 2 and Sector 3 will follow same pattern to get tails connected.
Tails connections for distributed L18 with 2 x FXED:
FXED 1.1.1 Ant1 > 1800/2100/2300/2600 combiner A -> TX/RX Antenna High Band 1 H+ (+45)
FXED 1.1.1 Ant2 > 1800/2100/2300/2600 combiner C -> RX Antenna High Band 2 H+ (+45)
FXED 1.3.1 Ant1 > 1800/2100/2300/2600 combiner B -> TX/RX Antenna High Band 1 H- (-45)
FXED 1.3.1 Ant2 > 1800/2100/2300/2600 combiner D -> RX Antenna High Band 2 H- (-45)
Please note that Antenna High Band 3 and 4 may be allocated to Optus L18 at VHA lead site in
actual plumbing diagram.
18 / 55
4.2 RF tails connections for distributed 2T4R L18 with 1 x FXED per sector
The below diagram illustrates tails connections for distributed L18 at Sector 1.
Tails connections for distributed L18:
FXED Ant1 > 1800/2100/2300/2600 combiner A -> TX/RX Antenna High Band 1 H+ (+45)
FXED Ant2 > 1800/2100/2300/2600 combiner C -> RX Antenna High Band 2 H+ (+45)
FXED Ant3 > 1800/2100/2300/2600 combiner B -> TX/RX Antenna High Band 1 H- (-45)
FXED Ant4 > 1800/2100/2300/2600 combiner D -> RX Antenna High Band 2 H- (-45)
Please note that Antenna High Band 3 and 4 may be allocated to Optus L18 at VHA lead site in
actual plumbing diagram.
19 / 55
5 RF tails connections for 2T2R L7 configuration
Stacked L7 (FRPA in shelter)
Please follow below instruction to connect RF tails when FRPA is in shelter.
Sector 1: A feed is connected to FRPA Ant 1, and B feed is connected to FRPA Ant 2.
Distributed L7 (3xFRPA on monopole)
20 / 55
Please follow below instruction to connect tails when FRPAs are on monopole / roof.
Each L7 sector has its own FRPA.
A feed is connected to FRPA Ant 1, and B feed is connected to FRPA Ant 3 at all 3
sectors.
Note:
L7 FRPA has no internal Bias-T at Antenna port 2, 4 and 6. Those ports are DC short. DC / AISG bus will
be pulled down together with connected antenna line devices, if L7 FRPA port 2, 4 or 6 combines with
any feed from other technologies as current master of MHA / RET.
Recommendation is to separate A and B feeds, combining A feeds within one antenna line; B feeds
following a separate antenna line (feeders, combiners and ALD). DC should be then provided to MHA
via A feeds to avoid DC short.
Ensure that L7 A feed is going to same combiner with A feeds from other technologies, L7 B feed is
going to same combiner with B feeds from other technologies.
6 RF tails connections for 2T4R L7 configuration

with 2xFRPA
The below diagram illustrates tails connections for 2T4R L7 at Sector 1.
Tails connections for 2T4R L7 with 2 x FRPA:
FRPA 1 Ant1 > 700 MHA A port -> TX/RX Antenna Low Band 1 H+ (+45)
FRPA 1 Ant2 > 700/850/900 combiner A -> RX Antenna Low Band 2 H+ (+45)
FRPA 2 Ant1 > 700 MHA B port -> TX/RX Antenna Low Band 1 H- (-45)
FRPA 2 Ant2 > 700/850/900 combiner B -> RX Antenna Low Band 2 H- (-45)
Note:
21 / 55
DC stop may be required on FRPA 1 ANT 2 if 700/900 dual band or 700/850/900 tri -band MHA is
in use.
7 3CC CA FSMFs Interconnection Cable Installation

7.1 SRIO Cable Installation
Connect the multimode LC to LC optical cable to the both FSMF main SRIO ports as per shown
connection diagram below.
22 / 55
7.2 HDMI Synchronisation Cable Installation
Connect the HDMI cable from Sync Out port of the 2300 LTE TDD FSMF to the Sync IN port of the
1800 LTE FDD FSMF.
IMPORTANT: Ensure that the exact cable length and Nokia product code for the cable is recorded
and tracked with the site build documentation.
23 / 55
8 Commissioning
8.1 Power on FSMF and all RF modules
8.2 Connect to site with BTS Site Manager
1. Launch BTS Site Manager
2. Select Disable, then Close
24 / 55
3. New FSMF is delivered with preinstalled LN4.0 1.2 (LN4.0 ENB 1202_781_57) SW
25 / 55
8.3 SW upgrade from RL40 1.2 to RL60 1.1 (LN6.0_ENB_1311_764_08)
Upgrade SW by selecting Software and Update SW to BTS Site
Select Browse
Select LN6.0_ENB_1311_764_08_release_BTSSM_downloadable.zip
Select Open
26 / 55
Tick Activate SW after update box
Select Update
8.4 SW upgrade from RL60 1.1 to RL70 2.3.1 (LN7.0_ENB_1407_586_18)
Upgrade SW by selecting Software and Update SW to BTS Site

Select Browse
Select LN7.0_ENB_1407_586_18_release_BTSSM_downloadable.zip
Select Open
27 / 55
Tick Activate SW after update box
Select Update
8.5 Commissioning TRS only
If FRPA is connected to FSMF EIF2/RF/EXT 6, FSMF cant detect FRPA until TRS is commissioned
with Enable FSM EIF2 as RP3-01 interface ticked.
Choose Target - TRS only

Commissioning type - Planned
Select Commissioning file
28 / 55
Click Next
Continue with Send Parameters
8.6 RF units detection
Switch on RF units power and wait until RF modules are detected by system module.
The FRPA will show up as not commissioned.
If incompatible SW is detected, then perform a SW upgrade (reload the SW).
29 / 55
The same SW should be used as already running (LN7.0_ENB_1407_586_18).
Go to Software -> Update SW to BTS Site, choose

LN7.0_ENB_1407_586_18_release_BTSSM_downloadable.zip -> Update
8.7 BTS Site commissioning steps
8.7.1 Introduction
After the FRPA is detected start BTS Commissioning
Select BTS site (check both, BTS and TRS)
Select Template
Select Commissioning file and browse for the new L18+L7 xml commissioning file as received
from RIC
30 / 55
Continue with Next
31 / 55
8.7.2 L18 MHA commissioning
Please ensure MHAs are set properly according to plumbing

diagram.
Please call RIC to verify MHA settings after commissioning.
It is mandatory to fill in correct MHA product code and
serial number as per physical MHA in case MHA in use
option is configured. Cells may stay disabled if MHA
product code / serial number are left blank or filled in
with incorrect information.
Please follow attached document to find out MHA product code and serial number. Same steps
are applied to L18.
Steps to find MHA

Serial number and Product code.docx
8.7.3 L7 MHA commissioning
32 / 55
The following procedure is for L7 MHA commissioning.
Please call RIC to verify MHA settings after commissioning.

It is mandatory to fill in correct MHA product code and
serial number as per physical MHA in case MHA in use
option is configured. Cells may stay disabled if MHA
product code / serial number are left blank or filled in
with incorrect information.L7 Antenna Line Management
8.7.3.1 L7 Antenna Line Management
L18 Antenna Line Management settings remain unchanged. Therefore ensure the L1800 settings
are the same as prior the L700 FRPA radio module installation.
L7 Antenna Line Management should be set according to plumbing diagram.
Scenario 1:
- L700 tails are connected to triplexer in shelter. L700 is sharing same antenna line as U9 /
VHA 850. 700/900 dual band or 700/850/900 Tri band MHA is controlled by U9 / VHA
850.
Please refer to BALLAJURA plumbing diagram.
BALLAJURA.pdf
33 / 55
Enable DC voltage on FRPA Ant 1&3&5 and disable AISG on all FRPA Antenna ports
Scenario 2:
- L700 feeders are connected to 700 single band MHA.
Please refer to MIRRABOOKA plumbing diagram.
Enable DC voltage and enable AISG on FRPA Ant 1&3&5
34 / 55
Scenario 3:
- L700 FPRAs are installed on monopole / roof.
Please refer to Buranda North plumbing diagram.
B0178.pdf
Disable DC voltage and AISG on all FRPA Antenna ports
35 / 55
Continue with Next
8.7.3.2 L7 AISG MHA settings
L18 AISG MHA settings remain unchanged. Therefore ensure the L1800 settings are the same as
prior the L700 FRPA radio module installation.
Follow the below instructions for L7 AISG MHA settings.
Scenario 1:
850.
36 / 55
AISG MHA Settings are not required.
Scenario 2:
Select This BTS option and choose Antenna port accordingly
37 / 55
Scenario 3:
- L700 FPRAs are installed on monopole / roof.

AISG MHA Settings are not required.
Continue with Next
38 / 55
8.7.3.3 L7 AISG MHA settings
L18 Antenna Line Settings remain unchanged. Therefore ensure the L1800 settings are the same
as prior the L700 FRPA radio module installation.
Follow the below instructions for L7 Antenna Line Settings.
Scenario 1:
850.
Settings:
Choose MHA in use and set MHA gain 13dB in all FRPA legs
MHA type is set to other
Please contact RIC to find out MHA serial number and product code for each sector.
39 / 55
40 / 55
41 / 55
Scenario 2:
Change of Antenna Line Settings is not required
42 / 55
Scenario 3:
- L700 FPRAs are installed on monopole / roof with no MHA.
Keep default Antenna Line Settings for all FRPA legs

Change of Antenna Line Settings is not required
Continue with Next
43 / 55
8.7.4 Send Parameters
Continue with Send Parameters
8.7.5 Additional Site Settings

No need to change
Continue with Next
44 / 55
8.7.6 Site Testing
Site tests -> press Test,
Then select Normal and Start.
Wait around 12 sec until all tests are completed.
45 / 55
Check test results and if all are Pass, then continue with Next
46 / 55
8.7.7 Commissioning Report
Save the BTS Commissioning Report
Select the desired location and change the File name if required.
Continue with Save, then with Finish
47 / 55
8.8 Retrieve certificate
1. Select IP -> Navigate to tab Application Addresses

Make sure to take a note of the original Management plane IP address before changing it.
Select VLAN interface IP as Management plane
Click Send
2. Then perform site reset manually
48 / 55
3. Check if certificate has been successfully retrieved
Select Configuration -> Certificate Management
Make sure BTS certificate appear in tab BTS Certificates
4. Change Management plane IP back to the original and click Send
49 / 55
5. Perform site reset manually
8.9 Commissioning completed
After successful BTS commissioning the site status should be

OAM connected
On air
TRS commissioned
50 / 55
9 Check L7 & L18 Cell RSSI level
BTS PM will be available in 15 minutes after cell is unlocked.
RSSI_PUCCH_AVG and RSSI_PUSCH_AVG need to be checked from BTS Site Manager.
RSSI_PUCCH_AVG
RSSI_PUCCH_AVG should be between -108 dBm and -102 dBm.
If RSSI_PUCCH_AVG is out of the range, please contact RIC for troubleshooting.
e.g. Local cell 49
RSSI_PUSCH_AVG
RSSI_PUSCH_AVG should be between -115 dBm and -102 dBm.
If RSSI_PUSCH_AVG is out of the range, please contact RIC for troubleshooting.
e.g. Local cell 49
51 / 55
10 Test call
10.1 L18 testing
Lock UE (Samsung) to LTE network

Type: *#2263#
Select [4] LTE Band Preference
Select [5] LTE B3 in L1800 case
Type: *#0011# to check EARFCN & PCI value
Start call tests. Unlock one sector at a time and record the downlink and uplink throughput. Als o
make a note of the Round trip time.
Each LTE1800 Sector should offer up to 100Mbit/s downlink and 30Mbit/s uplink speeds.
52 / 55
10.2 L7 testing
The L7 testing is required after L700 integration.
Please follow attached testing instruction and fill in test result form.
L700-Testing
document.docx
Sector 1 Sector 2 Sector 3

RSRP PCI SNR RSRP PCI SNR RSRP PCI SNR
-61 346 30 -59 347 30 -62 345 30
Att.
Test Items Att. 1 2 Att. 3 Att. 1 Att. 2 Att. 3 Att. 1 Att. 2 Att. 3
DL TP (Mbps) 71.34 71 69.87 70.23 70.48 70.04 69.25 70.17 69.98
UL TP (Mbps) 20.54 20 20.31 19.51 20.09 19.41 19.99 19.23 19.48
Latency (ping, ms) 22.7 21.2 20.1 19.9 20.8 25 21.1 26.7 17.9
FD-LTE 4G to FD-LTE
4G- Call OK OK OK OK OK OK OK OK OK
FD-LTE 4G to 3G- Call OK OK OK OK OK OK OK OK OK
SMS OK OK OK OK OK OK OK OK OK
MMS OK OK OK OK OK OK OK OK OK
HTTP: Open
www.smh.com.au OK OK OK OK OK OK OK OK OK
Please ensure UE camps on L7 cell before making test call.
53 / 55
11 References
11.1 4G LTE bands
4G LTE bands
B1 (2100)
B2 (1900)
B3 (1800)
B5 (850)
B7 (2600)
B8 (900)
B28 (700)
B40 (2300)
11.2 SFP modules used in L7/L18/L23/L26 eNB
SFP modules for 3 Gbps RP3-01 link speed
SFP modules for RP3-01 6 Gbps link speed
54 / 55
11.3 FSMF LMP connector pin map
55 / 55

L7-L18 Commissioning and Integration With FXED

Uploaded by

Copyright:

Available Formats

L7-L18 Commissioning and Integration With FXED

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

L7-L18 Commissioning and Integration With FXED

Uploaded by

Copyright:

Available Formats

L7/L18 commissioning and integration with FXED

7/25/2016 Work instruction For internal use Nokia 2016

2.1.1 HW for site build configurations ..................................................................................5

2.1.2 Additional HW for 3CC CA configuration .....................................................................8

2.3 L7/L18 frequency allocation .......................................................................................10

2.4 XML Commissioning Files.............................................................................................10

3 L7/L18 connectivity diagram ......................................................................................11

4 L18 RF tails connections for distributed 2T4R configuration.....................................17

5 RF tails connections for 2T2R L7 configuration ..........................................................20

6 RF tails connections for 2T4R L7 configuration with 2xFRPA .....................................21

7 3CC CA FSMFs Interconnection Cable Installation ......................................................22

7.1 SRIO Cable Installation.................................................................................................22

7.2 HDMI Synchronisation Cable Installation.....................................................................23

8.1 Power on FSMF and all RF modules .............................................................................24

8.2 Connect to site with BTS Site Manager .......................................................................24

8.3 SW upgrade from RL40 1.2 to RL60 1.1 (LN6.0_ENB_1311_764_08) ........................26

8.4 SW upgrade from RL60 1.1 to RL70 2.3.1 (LN7.0_ENB_1407_586_18) .....................27

8.5 Commissioning TRS only ..............................................................................................28

8.6 RF units detection........................................................................................................29

8.7 BTS Site commissioning steps.....................................................................................30

8.7.1 Introduction .................................................................................................................30

8.7.2 L18 MHA commissioning .............................................................................................32

7/25/2016 Work instruction For internal use Nokia 2016

8.7.3.1 L7 Antenna Line Management.....................................................................................33

8.7.3.2 L7 AISG MHA settings ..................................................................................................36

8.7.3.3 L7 AISG MHA settings ..................................................................................................39

8.7.4 Send Parameters .........................................................................................................44

8.7.5 Additional Site Settings................................................................................................44

8.7.6 Site Testing ..................................................................................................................45

8.7.7 Commissioning Report ................................................................................................47

8.8 Retrieve certificate ......................................................................................................48

8.9 Commissioning completed ..........................................................................................50

9 Check L7 & L18 Cell RSSI level .....................................................................................51

10 Test call ........................................................................................................................52

10.1 L18 testing ...................................................................................................................52

10.2 L7 testing .....................................................................................................................53

11.1 4G LTE bands ...............................................................................................................54

11.2 SFP modules used in L7/L18/L23/L26 eNB ...............................................................54

11.3 FSMF LMP connector pin map .....................................................................................55

7/25/2016 Work instruction For internal use Nokia 2016

7/25/2016 Work instruction For internal use Nokia 2016

HW requirement includes two parts.

- HW for site build configurations

2.1.1 HW for site build configurations

7/25/2016 Work instruction For internal use Nokia 2016

3. 2xFXED+1xFRPA L18 stacked 2T4R+L7 stacked 2T2R

4. 1xFXED+1xFRPA L18 stacked 2T2R+L7 stacked 2T2R

7/25/2016 Work instruction For internal use Nokia 2016

5. 1xFXED+2xFRPA L18 stacked 2T2R+L7 stacked 2T4R

6. 2xFXED+2xFRPA L18 stacked 2T2R+L7 stacked 2T4R

7. 3xFXED+2xFRPA L18 distributed 2T2R/2T4R+L7 stacked 2T4R

7/25/2016 Work instruction For internal use Nokia 2016

* Optional use of FBBA+FBBC is allowed.

**** Note: FOSI and SM links are also possible.

2.1.2 Additional HW for 3CC CA configuration

Module / Item Name Description Qty

7/25/2016 Work instruction For internal use Nokia 2016

Please refer to Chapter 7 for 3CC Cabling.

Ensure all Software listed is available prior to Installation and Commissioning.

7/25/2016 Work instruction For internal use Nokia 2016