Yamaha Rx-sl100 Sl100rds

AV RECEIVER/AV AMPLIFIER
RX-SL100/RX-SL100RDS SERVICE MANUAL
IMPORTANT NOTICE
This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already
known and understood by the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons,
we advise all YAMAHA product owners that any service required should be performed by an authorized
YAMAHA Retailer or the appointed service representative.
IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or
recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.
The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and
service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable
RX-SL100/RX-SL100RDS
and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please
contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).
IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.
CONTENTS
TO SERVICE PERSONNEL .......................................... 2 AMP ADJUSTMENT / ..................................... 36
FRONT PANELS ............................................................ 4 DISPLAY DATA ........................................................... 37
REAR PANELS .......................................................... 5~6 IC DATA ................................................................. 38~43
REMOTE CONTROL PANELS ...................................... 6 BLOCK DIAGRAM ................................................. 44~45
SPECIFICATIONS .................................................... 7~10 PIN CONNECTION DIAGRAM .................................... 46
INTERNAL VIEW ......................................................... 10 PRINTED CIRCUIT BOARD .................................. 47~57
DISASSEMBLY PROCEDURES / ........... 11~13 SCHEMATIC DIAGRAM ........................................ 59~65
SELF DIAGNOSIS FUNCTION (DIAG) / PARTS LIST ........................................................... 67~81
......................................... 14~35 REMOTE CONTROL .............................................. 82~83
D-AMP MODULE TROUBLESHOOTING /
- ........................................ 35
100876
P.O.Box 1, Hamamatsu, Japan
TO SERVICE PERSONNEL
1. Critical Components Information
AC LEAKAGE
Components having special characteristics are marked s and WALL EQUIPMENT TESTER OR
must be replaced with parts having specifications equal to those OUTLET UNDER TEST EQUIVALENT
originally installed.
2. Leakage Current Measurement (For 120V Models Only)

When service has been completed, it is imperative to verify
that all exposed conductive surfaces are properly insulated INSULATING
TABLE
from supply circuits.
Meter impedance should be equivalent to 1500 ohm shunted Leakage current must not exceed 0.5mA.
by 0.15F. Be sure to test for leakage with the AC plug in both polarities.
CAUTION
F1: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 5A, 125V
FUSE.
CAUTION
F1: REPLACE WITH SAME TYPE 5A, 125V FUSE.
ATTENTION
F1: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 5A, 125V.
WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where
applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and
possibly other entities) to cause cancer and/or birth defects or other reproductive harm.
DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REA-
SON WHATSOEVER!
Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose
eyes to solder/flux vapor!
If you come in contact with solder or components located inside the enclosure of this product, wash your hands before
handling food.
2
About Lead Free Solder /

The P.C.B.s installed in this unit are soldered using the
following solder.
Component Side / Foil Side /

DIGITAL P.C.B. Lead Solder / Lead Solder /
INPUT P.C.B. Lead Free Solder /
MAIN P.C.B. Lead Solder / Lead Free Solder /
POWER P.C.B. Lead Free Solder /
Among some types of lead free solder currently available,

it is recommended to use one of the following types for the
repair work.
Sn+Ag+Cu++
Sn + Ag + Cu (tin + silver + copper) Sn+Cu
+
Sn + Cu (tin + copper) Sn+Zn+Bi++
Sn + Zn + Bi (tin + zinc + bismuth)
Caution:
1. As the melting point temperature of the lead free solder 3040
is about 30C to 40C (50F to 70F) higher than that of
the lead solder, be sure to use a soldering iron suitable
to each solder.

2. If lead solder must be used, be sure to remove lead free
solder from each terminal section of the parts to be
replaced and from the area around it completely before
soldering, or make sure that the lead free solder and
lead solder melt together fully.
IMPEDANCE SELECTOR
(B, G models only)
IMPEDANCE SELECTOR
WARNING:
Do not change the IMPEDANCE SELECTOR
switch setting while the power to this unit is
on, otherwise this unit may be damaged.
3
FRONT PANELS
RX-SL100 (U, C, A, L, R, T, K models)
RX-SL100 (J model)
RX-SL100RDS (B, G models)
4
REAR PANELS
RX-SL100 (U, C models)
RX-SL100 (A model)
RX-SL100 (L model)
RX-SL100 (R model)
RX-SL100 (T model)
RX-SL100 (K model)
5
RX-SL100 (J model)
RX-SL100RDS (B, G models)
REMOTE CONTROL PANELS

RX-SL100 RX-SL100RDS
6
SPECIFICATIONS /
Audio Section / Residual Noise / (IHF-A network)
Minimum RMS Output Power (Power Amp. Section) / FRONT L/R ........................................... 150 V or less
() Channel Separation /
(1 kHz) (Vol -30 dB, Effect Off)
FRONT L/R DVD/CD, etc. (Input 5.1 k-ohms shorted, 1 kHz/10 kHz)
U, C models (0.9% THD, 6 ohms) ................... (FTC) 65W + 65W ....................................... 60 dB or more/45 dB or more
A, B, G, L, R, T, K, J models (0.9% THD, 6 ohms) ... 70W + 70W Tone Control Characteristics /
CENTER, SURROUND BACK BASS
U, C models (0.9% THD, 6 ohms) ................... (FTC) 65W + 65W Boost/Cut ........................................... 10 dB (60Hz)
A, B, G, L, R, T, K, J models (0.9% THD, 6 ohms) ... 70W + 70W TREBLE
SURROUND L/R Boost/Cut ......................................... 10 dB (20kHz)
U, C models (0.9% THD, 6 ohms) ................... (FTC) 65W + 65W Filter Characteristics /
A, B, G, L, R, T, K, J models (0.9% THD, 6 ohms) ... 70W + 70W FRONT L/R, SURROUND L/R SP Small (H.P.F.)
Maximum Power / (EIAJ, 1kHz, 10% THD) ........................................................ 90 Hz, 12 dB / oct.
FRONT L/R SUBWOOFER (L.P.F.) .................. 90 Hz, 18 dB / oct.
A, B, G, L, R, T, K, J models (6 ohms) ................. 100W
CENTER, SURROUND BACK Video Section /
A, B, G, L, R, T, K, J models (6 ohms) ................. 100W Video Signal Type /
SURROUND L/R U, C, R, K, J models ........................................... NTSC
A, B, G, L, R, T, K, J models (6 ohms) ................. 100W A, B, G, L, T models ............................................... PAL
Input Sensitivity / Input Impedance (/ Video Signal Level /
) ........................................................... 1 Vp-p / 75 ohms
(U, C, A, L, R, T, K, J models) Maximum Input Level /
DVD/CD, etc. ................................ 150 mV / 47 k-ohms ........................................................... 1.5 Vp-p or more
(B, G models) Signal to Noise Ratio /
VIDEO 2, EXT. IN, TV IN ............. 150 mV / 47 k-ohms ............................................................... 50 dB or more
Maximum Input Signal Level / (1 kHz, 0.5% Monitor Out Frequency Response /
THD)
(U, C, A, L, R, T, K, J models) Video Signal Level .................... 5 Hz to 10 MHz, -3 dB
DVD/CD, etc. .......................................... 2.0 V or more
(B, G models) FM Section / FM
VIDEO 2, EXT. IN, TV IN ....................... 2.0 V or more Tuning Range
Output Level / Output Impedance (/ U, C models .................................... 87.5 to 107.9 MHz
) A, B, G, T, K models ....................... 87.5 to 108.0 MHz
VCR OUT L, R models ........ 87.5 to 108.0 / 87.50 to 108.00 MHz
DVD/CD, etc. (U, C, A, L, R, T, K, J models) J model .............................................. 76.0 to 90.0 MHz
....................................................... 150 mV / 820 ohms 50dB Quieting Sensitivity / 50dB SN (IHF)
EXT., TV (B, G models) ................. 150 mV / 1 k-ohms (1kHz, 100% Mod.)
SUB WOOFER (FRONT SP: Small) ... 3.8 V / 1.2 k-ohms Mono ................................................. 2.8 V (20.2 dBf)
Headphone Jack Rated Output / Impedance ( Signal to Noise Ratio / (IHF)
/) Mono / Stereo ......................................... 73 dB / 70 dB
DVD/CD, etc. (1 kHz, 35 mV, 8 ohms) ... 100 mV / 100 ohms Harmonic Distortion /
Frequency Response / (1 kHz)
DVD/CD, etc. to FRONT L/R (20 Hz to 50 kHz) ... +0/-3.0 dB Mono / Stereo .......................................... 0.5 % / 0.5 %
Total Harmonic Distortion / (1 kHz, 35W, 6 Antenna Input /
ohms) ..................................................... 75 ohms unbalanced
(U, C, A, L, R, T, K, J models)
DVD/CD, etc. (Effect Off) to FRONT L/R ... 0.04 % or less AM Section / AM
(B, G models) Tuning Range /
EXT. IN (Effect Off) to FRONT L/R ............ 0.04 % or less U, C models ...................................... 530 to 1,710 kHz
Signal to Noise Ratio / (IHF-A network) A, B, G, T, K, J models ..................... 531 to 1,611 kHz
(U, C, A, L, R, T, K, J models) L, R models ............... 530 to 1,710 / 531 to 1,611 kHz
DVD/CD, etc. (Input shorted, 250 mV, Effect Off) to Antenna /
FRONT L/R ........................................... 98 dB or more ................................................................ Loop Antenna
(B, G models)
EXT. IN (Input shorted, 250 mV, Effect Off) to FRONT
L/R ......................................................... 98 dB or more
7
General /
Power Supply /
U, C models ...................................... AC 120 V, 60 Hz
A model ............................................. AC 240 V, 50 Hz
B, G models ...................................... AC 230 V, 50 Hz Manufactured under license from Dolby Laboratories.
L model ............................... AC 220 240 V, 50/60 Hz Dolby, Pro Logic, Surround EX, and the double-D symbol are
R model .............................. AC 110 120 V, 50/60 Hz trademarks of Dolby Laboratories.
T model ............................................. AC 220 V, 50 Hz
K model ............................................. AC 220 V, 60 Hz DOLBYPRO LOGICEX
J model .......................................... AC 100V, 50/60 Hz D
Power Consumption /
U, C models ....................................................... 100 W
A, B, G, L, R, T, K models ................................. 100 W "SILENT CINEMA" is a trademark of YAMAHA CORPORATION.
J model ............................................................... 145 W
SILENT THEATER

Standby Power Consumption (reference data) /

()
U, C, R, J models ................................................ 0.8 W
A, L, T, K models ................................................. 0.9 W
B, G models (Scart Off/On) .................... 0.9 W / 2.5 W
Dimensions / (W x H x D) DTS, DTS-ES Extended Surround and Neo: 6 are trademarks
............ 435 x 55.5 x 330 mm (17-1/8" x 2-3/16" x 13") of Digital Theater Systems, Inc.
Weight /
DTSDTS-ES ExtendedNeo:6
..................................................... 6.4 kg (14 lbs. 2 oz.)

Finish /
.................................................................... Silver color
Accessories /
Remote Control x 1, Battery (Manganese Dry) x 2, Indoor
FM Antenna x 1, AM Loop Antenna x 1, Cable Tag x 6
pairs AAC
* Specifications are subject to change without notice due

to product improvements.

DIMENSIONS /
U ........ U.S.A. model C .... Canadian model
(5/8")
A ........ Australian model B ..... British model 15.6
G ........ European model L ..... Singapore model
R ........ General model T ..... Chinese model
K ........ Korean model J ..... Japanese model
300 (11-13/16")
(9/16") 330.2 (13")
14.6
55.5 (2-3/16")
435 (17-1/8")
Unit : mm (inch)
: mm
8
Set Menu Table /

No. MAIN MENU SUB MENU VALUE [INITIAL]
1 SETUP ROOM S, [M], L
SWFR [YES], NONE
SPEAKERS 2, 3, 4, 5, [6]
SETTING OK [SET], CANCEL
BASIC CHECK OK [Yes], No
2 SP LEVEL L-R [Center] 10 step
C -10 to +10 dB, 1 dB step
SL -10 to +10 dB, 1 dB step
SB -10 to +10 dB, 1 dB step
SR -10 to +10 dB, 1 dB step
SWFR -20 to 0 dB, 1 dB step
1 SPEAKER SET CENTER SP LRG, [SML], NON
FRONT SP [LARGE], SMALL
SUR. SP LRG, [SML], NON
SUR. BACK LRG, [SML], NON
BASS OUT [BOTH], FRNT, SWFR
2 SP DISTANCE UNIT meters, [feet] (U, C models) / [meters], feet (A, B, G, L, R, T, K, J models)
FRONT 0.3 to 24.0 m [3.0 m], 0.1 m step
1.0 to 80.0 ft [10.0 ft], 0.5 ft step
CENTER 0.3 to 24.0 m [3.0 m], 0.1 m step
1.0 to 80.0 ft [10.0 ft], 0.5 ft step
SUR 0.3 to 24.0 m [3.0 m], 0.1 m step
1.0 to 80.0 ft [10.0 ft], 0.5 ft step
SUR. BACK 0.3 to 24.0 m [2.1 m], 0.1 m step
SOUND 1.0 to 80.0 ft [7.0 ft], 0.5 ft step
3 LFE LEVEL SP LFE -20 to [0 dB], 1 dB step
HP LFE -20 to [0 dB], 1 dB step
4 D. RANGE SP D.R [MAX], STD, MIN
HP D.R [MAX], STD, MIN
5 CENTER GEQ 100 Hz -6 to +6 dB [0 dB], 1 dB step
300 Hz -6 to +6 dB [0 dB], 1 dB step
1 kHz -6 to +6 dB [0 dB], 1 dB step
5 SP TONE CTRL SP BASS -10 to +10 dB [0 dB], 1 dB step
SP TRBL -10 to +10 dB [0 dB], 1 dB step
6 HP TONE CTRL HP BASS -6 to +3 dB [0 dB], 1 dB step
HP TRBL -6 to +3 dB [0 dB], 1 dB step
1 INPUT ASSIGN OPT 1 VCR, VIDEO1, DTV/CBL, [DVD/CD]
OPT 2 VCR, VIDEO1, [DTV/CBL], DVD/CD
COAX VCR, [VIDEO1], DTV/CBL, DVD/CD
2 INPUT MODE SET AUTO, LAST, [Fixed]
INPUT VCR AUTO, dts, AAC (J model only), Analog
VIDEO1 AUTO, dts, AAC (J model only), Analog
VIDEO2 AUTO, dts, AAC (J model only), Analog
DTV/CBL AUTO, dts, AAC (J model only), Analog
DVD/CD AUTO, dts, AAC (J model only), Analog
1 DISPLAY SET DIMMER -4 to [0], 1 step
2 MEM. GUARD [OFF], ON
3 AUDIO MUTE [- ], -50 dB, -20 dB
OPTION 4 DUAL MONO (J model only) [MAIN], SUB, ALL
5 Freq. Step (R, L models only) 9 kHz, [10 kHz]
6 GUI Lang (J model only) [ENG], JPN
7 STB SCART (B, G models only) [ON], OFF
9
The variable range of the parameter (Min/Max/Step) / //
Unit Pro Logic II / IIx Parameter Unit

DSP LEVEL -6 / +3 / 1 dB PLII / PLIIx PLII / PLIIx
DELAY 1 / 99 / 1 ms
Pro Logic II Music Parameter Unit
6 ch Stereo Parameter Unit PANORAMA OFF / ON
CT LEVEL 0 / 100 / 1 % DIMENSIONS -3 / +3 / 1
SL LEVEL 0 / 100 / 1 % CT WIDTH 0/7/1
SR LEVEL 0 / 100 / 1 %
SB LEVEL 0 / 100 / 1 % DTS Neo:6 Music Parameter Unit
C. IMAGE 0 / 0.5 / 0.1
INTERNAL VIEW
RX-SL100
1 2 3 4 5 6 7 8 1 POWER (1) P.C.B.
2 POWER (3) P.C.B.
3 POWER (11) P.C.B.
4 POWER (8) P.C.B.
5 POWER (10) P.C.B.
6 POWER (7) P.C.B.
7 INPUT (2) P.C.B.
8 AM / FM TUNER
9 DIGITAL P.C.B.
0 POWER (4) P.C.B.
A INPUT (1) P.C.B.
B D-AMP MODULE
C MAIN (4) P.C.B.

D MAIN (3) P.C.B.
E MAIN (2) P.C.B.
F MAIN (1) P.C.B.
G POWER (5) P.C.B.
H POWER TRANSFORMER
IH G F E D C B A 0 9
I POWER (6) P.C.B.
RX-SL100RDS
1 2 3 4 5 6 7 1 POWER (2) P.C.B.
2 POWER (1) P.C.B.
3 POWER (3) P.C.B.
4 POWER (9) P.C.B.
5 POWER (12) P.C.B.
6 INPUT (2) P.C.B.
7 AM / FM TUNER
8 DIGITAL P.C.B.
9 POWER (4) P.C.B.
0 INPUT (1) P.C.B.
A D-AMP MODULE
B MAIN (4) P.C.B.
C MAIN (3) P.C.B.
D MAIN (2) P.C.B.
E MAIN (1) P.C.B.
F POWER (5) P.C.B.
G POWER TRANSFORMER
HG F E D C B A 0 9 8 H POWER (6) P.C.B.
10
DISASSEMBLY PROCEDURES /
* The description below uses RX-SL100RDS (G model) RX-SL100RDS (G model)
as a representative model.
(Remove parts in the order as numbered.)

Disconnect the power cable from the AC outlet. AC
1. Removal of Top Cover (Fig. 1) 1. Fig. 1

a. Remove 2 screws (1) and 4 screws (2). a. 1224
b. Slide the Top Cover rearward to remove it. b.
2. Removal of Front Panel (Fig. 1) 2. Fig. 1

a. Remove 2 screw (3) and 5 screws (4). a. 3245
b. Remove CB161, CB305, CB401 and CB410. b. CB161CB305CB401CB410
c. Remove the Front Panel forward. c.
3. Removal of DIGITAL P.C.B. (Fig. 2) 3. DIGITAL P.C.B.Fig. 2

a. Remove 4 screws (5). a. 54
b. Remove CB301 ~ CB303, CB306 ~ CB308. b. CB301CB303CB306CB308
c. Remove the DIGITAL P.C.B. upward. c. DIGITAL P.C.B.
4. Removal of MAIN (1) ~ (4) and D-AMP Modules 4. MAIN14D-AMP MODULE

a. Remove 3 screws (6). (Fig. 4) a. 63Fig. 3
b. Remove CB71 ~ 73, CB601, CB631 , CB661 and CB695. b. CB71CB73CB601CB631CB661CB695
(Fig. 2) Fig. 2
b. Remove MAIN (1) ~ (4) and D-AMP Modules leftward. c. MAIN14D-AMP MODULE
(Fig. 2) Fig. 2
CB307
(B, G models only)
Top Cover
CB303 CB306
2 5
CB301
1 DIGITAL P.C.B.
2 5
CB308
CB302
MAIN (3) P.C.B.

CB601
3 CB631
CB71
Front Panel CB72
1 MAIN (1) P.C.B.
CB73
CB401 6
4 3 6
CB661
6
CB161
CB305
CB410 MAIN (4) P.C.B. CB695
4 4 MAIN (2) P.C.B.

D-AMP Modules
(CH1~CH6)
Fig. 1 Fig. 2
11
5. Removal of Rear Panel (Fig. 3) 5. Fig. 3

a. Remove 1 screw (7) and 3 screws (8). a. 7183
b. Remove the Rear Panel rearward. b.
c. Remove CB4, CB6, CB51, CB404 and CB406. c. CB4CB6CB51CB404CB406
6. Removal of INPUT (1) and POWER (9) P.C.B. (Fig. 4) 6. INPUT (1) P.C.B.POWER (9) P.C.B.Fig. 4
a. Remove 2 screws (9) and then remove the Support/ a. 92/PCB
PCB. b. 02
b. Remove 2 screws (0). c. INPUT (1) P.C.B.POWER (9) P.C.B.
c. Remove the INPUT (1) and POWER (9) P.C.B.s.
7. Removal of POWER (1) P.C.B. (Fig. 4) 7. POWER (1) P.C.B.Fig. 4

a. Remove CB9. a. CB9
b. Remove 3 screws (A). b. A3
c. Remove the POWER (1) P.C.B.. c. POWER (1) P.C.B.
8. Removal of Power Transformer (Fig. 4) 8. Fig. 4

a. Remove 4 screws (B). a. B4
b. Remove the Power Transformer. b.
CB9 A Power (1) P.C.B.
Power Transformer
Rear Panel A

CB51 B
Support / PCB
/ PCB
CB6 8
9
CB4 7 8 Power (9) P.C.B.
8 9
B
CB406
Input (1) P.C.B.
CB404
Fig. 3 Fig. 4
When checking the P.C.B.: P.C.B.

Remove the Front Panel, Rear Panel, P.C.B.s, Power P.C.B.
Transformer and place all of the upside down for
checking. (Fig. 5) Fig. 5
Reconnect all cables (connectors) that have been

disconnected.
Be sure to use the extension cable for servicing for
the following section. DIGITAL P.C.B. CB301 INPUT (2) P.C.B. CB552:
DIGITAL P.C.B. CB301 INPUT (2) P.C.B. CB552: MFA15400 (15P 400mm)
MFA15400 (15P 400mm) DIGITAL P.C.B. CB302 INPUT (1) P.C.B. CB411:
DIGITAL P.C.B. CB302 INPUT (1) P.C.B. CB411: MFA15200 (15P 200mm)
MFA15200 (15P 200mm)
12
DIGITAL P.C.B. CB303 POWER (1) P.C.B. CB5: DIGITAL P.C.B. CB303 POWER (1) P.C.B. CB5:
MFA18400 (18P 400mm) MFA18400 (18P 400mm)
DIGITAL P.C.B. CB306 INPUT (1) P.C.B. CB409: DIGITAL P.C.B. CB306 INPUT (1) P.C.B. CB409:
MFA40400 (40P 400mm) MFA40400 (40P 400mm)
DIGITAL P.C.B. CB307 POWER (12) P.C.B. CB303: DIGITAL P.C.B. CB307 POWER (12) P.C.B. CB303:
MFA15400 (15P 400mm) [B, G models only] MFA15400 (15P 400mm) [B, G models only]
When connecting the flat cable, use care for the
polarity.
In this unit, each ground of the following P.C.B.s is P.C.B.
grounded to the chassis. When any of these P.C.B.s P . C . B .
has been removed from the chassis, be sure to
reconnect its ground to the chassis with a jumper wire
or the like. 1. POWER (1) P.C.B.:
1. POWER (1) P.C.B.: G1
G1 (near the sub-transformer) 2. POWER (5) P.C.B.:
2. POWER (5) P.C.B.: G161
G161 (input terminal on the front) 3. POWER (7), (8), (10), (11) P.C.B.:
3. POWER (7), (8), (10), (11) P.C.B.: PJ201, PJ221, PJ261, PJ281
PJ201, PJ221, PJ261, PJ281 (pin jack) U, C, A, L, R, T, K, J models
(U, C, A, L, R, T, K, J models) 4. POWER (12) P.C.B.:
4. POWER (12) P.C.B.: CB302, CB304SCART B, G models
CB302, CB304 (SCART terminal) (B, G models) 5. INPUT (1) P.C.B.:
5. INPUT (1) P.C.B.: G401, G402
G401, G402 6. DIGITAL P.C.B.:
6. DIGITAL P.C.B.: G1, G2, G3, G4
G1, G2, G3, G4
CB307 CB306
Front Panel

CB303
Power Transformer D-AMP Modules

CB301
CB302
DIGITAL P.C.B.
Cloth
POWER (1) P.C.B.
CB411
CB5
CB409
Cloth

CB552
INPUT (1) P.C.B.
Rear Panel
Cloth

CB303
POWER (12) P.C.B.
INPUT (2) P.C.B.
Fig. 5
13
SELF DIAGNOSIS FUNCTION (DIAG)

There are 15 DIAG menu items, each of which has sub- 15
menu items. Listed in the table below are menu items and
sub-menu items.
No DIAG menu sub-menu

1 DSP THROUGH 1. ANALOG BYPASS
2. YSS 0dB
3. YSS Front 0dB
4. YSS FULL BIT
5. YSS FULL BIT F
2 RAM THROUGH RAM 0dB
3 PRO LOGIC / 1. PRO LOGIC I
NEO6 2. PRO LOGIC II
3. Neo:6
4 SPEAKERS SET 1. MAIN: SMALL 0dB
2. CENTER: NONE
3. LFE/BASS: MAIN
4. Front Mix: 5ch
5. Rear Center power
6. Tone Control Flat
7. Tone Control +10dB
8. Tone Control -10dB
5 HEADPHONE TEST 1. MAIN 12 dB margin
2. MAIN 15 dB margin
6 OTHER INPUT EXTERNAL DECODER (Not applied to this model / )
7 DISPLAY CHECK 1. VFD CHECK (Initial display / )

2. VFD DISP OFF (All segments OFF / )
3. VFD DISP ALL (All segments ON 100% / 100%)
4. VFD DIMMER (All segments ON 50% / 50%)
5. CHECKED PATTERN (ON in lattice / )
8 MANUAL TEST 1. TEST ALL
2. TEST MAIN L
3. TEST CENTER
4. TEST MAIN R
5. TEST REAR R
6. TEST REAR CENTER
7. TEST REAR L
8. TEST LFE
9 FACTORY PRESET 1. PRESET INHIBITED (memory initialization inhibited / )
2. PRESET RESERVED (memory initialized / )
10 AD DATA CHECK 1. DC (protection) / UC (protection)
/FAN TEST 2. THM/Fan
3. REC-OUT (Not applied to this model / )
4. IMP SW (Not applied to this model / )
5. K0/K1 (panel key)
6. FAN DRIVE TEST: HIGH
7. FAN DRIVE TEST: MID
8. FAN DRIVE TEST: LOW
14
No DIAG menu sub-menu

11 IF STATUS 1. INSIDE STATUS 1 (5 Byte)
2. INSIDE STATUS 2 (3 Byte)
3. CHANNEL STATUS 1 (5 Byte)
8. BSI (YSS) 1 (5 Byte)
12. BSI (CS) 1 (5 Byte)
13. BSI (CS) 2 (5 Byte)
14. BSI (CS) 3 (5 Byte)
15. BSI (CS) 4 (5 Byte)
16. BSI (CS) 5 (1 Byte)
17. YSS938-1 (5 Byte)
18. YSS938-2 (5 Byte)
19. YSS938-3 (4 Byte)
20. SECOND DECODER (3 Byte)
21. Mute Trigger (5 Byte)
12 DSP RAM CHECK 1. YSS938 BUS CHECK
2. PLD/SRAM BUS CHECK
13 SD DL CODE 1. ROM DATA Version
2. TOC Area 0
3. TOC Area 1
4. TOC Area 2
5. TOC Area 3
6. TOC Area 4
7. TOC Area 5
8. Sum check Area 0
9. Sum check Area 1
10. Sum check Area 2
14 SOFT SWITCH 1. SW MODE
2. MODEL SETTING
3. DESTINATION
4. RDS EXIST
5. ZONE 2 EXIST
6. VIDEO FORMAT
15 ROM VERSION/CHECK SUM/ 1. VERSION
PORT 2. CHECK SUM ALL/PROGRAM
3. PORT
4. AAC PORT
15
Starting DIAG
Press the STANDBY/ON key while simultaneously INPUTSTANDBY/ON
pressing the INPUT key.
Starting DIAG in the protection cancel

mode
If the protection function works and causes hindrance to
trouble diagnosis, cancel the protection function as

described below, and it will be possible to enter the DIAG
mode. (The protection functions other than the excess INPUTSTANDBY/ON
current detect function will be disabled.) INPUT3
Press the STANDBY/ON key while simultaneously FLSLEEP
pressing the INPUT key. At this time, keep pressing the
INPUT key for 3 seconds or longer.
In this mode, the SLEEP segment of the FL display of the
main unit flashes to indicate that the mode is DIAG mode

with the protection functions disabled.

CAUTION!
Using this product with the protection function disabled may
cause damage to itself. Use special care for this point when
using this mode.
Canceling DIAG
1 Before canceling DIAG, execute setting for PRESET of N o . 9
DIAG menu No.9 (Memory initialization inhibited or FACTORY PRESET/
Memory initialized).
* In order to keep the user memory stored, be sure to P R E S E T
select PRESET INHIBITED (Memory initialization INHIBITED
inhibited). STANDBY/ON
2 Turn off the power by pressing the STANDBY/ON key
of the main unit.
16
Display provided when DIAG started

The FL display of the main unit displays the protection FL
function history data and the version (1 alphabet) and the 1No.1 DSP
DIAG menu [sub-menu (ANALOG BYPASS) of DIAG menu THROUGHANALOG BYPASS
No.1 DSP THROUGH] a few seconds later.
When there is no history of protection function: :
Opening message / DIAG menu display /

When there is no history Version (1 alphabet)
of protection function 1

After a few seconds

When there is a history of protection function: :

When there is a history of protection
function due to excess current Version (1 alphabet)
1

Cause: An excessive current flowed through the power

amplifier.
Supplementary information: As current of the power
transistor is detected, the abnormal channel can be
identified by checking the current detect transistor.

Turning on the power without correcting the abnormality
will cause the protection function to work immediately and
the power supply will instantly be shut off.
Note)
Applying the power to a unit without correcting the
abnormality can be dangerous and cause additional
circuit damage.
The output transistors in each amplifier channel
should be checked for damage before applying any
power.
Amplifier current should be monitored by measuring
across the emitter resistors for each channel.

function due to abnormal DC output Version (1 alphabet)
DC 1

Cause: DC output of the power amplifier is abnormal. DC

3

will cause the protection function to work 3 seconds later
and the power supply will be shut off.
17

function due to excessive UCD amplifier
temperature
UCD Version (1 alphabet)
1
Voltage display in %
%
Cause: The temperature of the UCD amplifier is excessive. UCD

Supplementary information: The abnormal voltage is 5V500%%
displayed in % based on 5V as 500%.
1

will cause the protection function to work 1 second later
Cause: Abnormal temperature of radiator

Supplementary Information: The abnormal voltage is 5V500%
displayed in % based on 5V as 500%.
1

will cause the protection function to work 1 second later
* Additional causes of protection can be due to loose CPU

connections, associated components, CPU, etc.
* For the protection voltage value, refer to DIAG menu
No.10 described later. No.10
History of protection function

When the protection function has worked, its history is
stored in memory with a backup. Even if no abnormality
is noted while servicing the unit, an abnormality which
has occurred previously can be defined as long as the
backup data has been stored. No.9PRESET
The history of the protection function is cleared when RESERVED

DIAG is cancelled by selecting PRESET RESERVED
(Memory initialized) of DIAG menu No.9 or when the
backup data is erased.
Display during menu operation

During the DIAG operation, the function at work is indicated FL
on the FL indicator. The contents displayed during the
function operation are described in the later section on
details of functions.
18
Operation procedure of DIAG menu and

SUB-MENU
Entering Menu Select Mode No.115
There are 15 MENU items, each of which has some SUB-
MENU items.
To select a DIAG MENU item or a SUB-MENU item, press TUNERFL
the "TUNER" key to enter the menu select mode. (The TUNER
"TUNER" segment of the FL display on this unit flashes to
indicate that the menu select mode is at work.) 5
* When about 5 seconds elapse with no menu item TUNER
selected, the menu select mode is cancelled. (The
"TUNER" segment lights up.) TUNER
Pressing the "TUNER" key again will restore the menu
select mode setting.

Selection of DIAG MENU item or SUB-MENU item VOLUME/SELECT
While in the menu select mode, turn the "VOLUME/
SELECT" knob. Items advance forward when the knob is
turned clockwise and rearward when it is turned

counterclockwise.

VOLUME/SELECT

Switching selection of DIAG MENU item and SUB-
MENU item
While in the menu select mode, press the "VOLUME/
SELECT" knob. Each pressing changes between the DIAG
MENU item selection state and SUB-MENU item selection
state alternately.
Functions in DIAG mode
In addition to the DIAG menu items, functions as listed
below are available.
Input selection
Center/Rear/Rear Center/Subwoofer level adjustment
Muting /
Power on/off
Master volume

* Functions related to the tuner and the set menu are not INPUT2
available. N o . 1 1I F
* It is possible to confirm Menu No.11 IF STATUS while STATUS
keeping the signal process (operation status) of each
DIAG menu by pressing the "INPUT" key twice.
Initial settings used to start DIAG

The following initial settings are used when starting DIAG.
When DIAG is canceled, these settings are restored to
those before starting DIAG.
-40dB
Master volume: -40dB DVD6CH INPUT
Input: DVD (6CH INPUT OFF) 0dB
Effect level: 0dB
Audio mute: OFF LARGE / BASS OUT = BOTH
Speaker setting: LARGE / BASS OUT = BOTH D S P T H R O U G H ( 1 . A N A L O G
DIAG menu: DSP THROUGH (1. ANALOG BYPASS) BYPASS)
19
Details of DIAG menu

With full-bit output specified in some modes, it is possible
to execute 0dBFS output without head margin in each 0dBFS
channel.
1. DSP THROUGH
1. DSP THROUGH MAIN L/RYSS938Sub DSP
Sub DSP of YSS938 is selected for MAIN L/R output.
ANALOG BYPASS
ANALOG BYPASS L/RDSP
The signal for L/R is output as it is without passing
through the DSP section.
Reference data
INPUT: DVD ANALOG
SWFR: 50 Hz, Others: 1 kHz
SPEAKER OUTPUT (1 kHz) SUBWOOFER

Input level Volume
FRONT L/R CENTER SURROUND L/R SURROUND BACK OUTPUT (50 Hz)
Both ch, -20 dBm -10 dB +19.5 dBm - - - -
YSS 0dB YSS 0dB

The signal is output including the head margin.
Head margin:
Main L/R: 0dBFS, Center: -6dBFS, Main L/R: 0dBFSCenter: -6dBFS
Rear Center: -6dBFS, RL/RR: -12dBFS, Rear Center: -6dBFSRL/RR: -12dBFS
SWFR: Add L/R signal at -20dBFS. SWFR: L/R-20dBfs
Reference data
INPUT: DVD ANALOG

Input level Volume
Both ch, -20 dBm -10 dB +16.9 dBm +27.0 dBm +27.0 dBm +27.0 dBm -1.3 dBm
YSS Front 0dB YSS Front 0dB

The front CH signal including the head margin is output CHCH
at the main CH.
Head margin:
Main L/R: 0dBFS, Center: -6dBFS, Main L/R: 0dBFSCenter: -6dBFS
Rear Center: -6dBFS, RL/RR: -12dBFS, Rear Center: -6dBFSRL/RR: -12dBFS
SWFR: Add L/R signal at -20dBFS. SWFR: L/R-20dBfs
Reference data
INPUT: DVD ANALOG
Input level Volume
Both ch, -20 dBm -10 dB +22.5 dBm - - - -
20
YSS FULL BIT YSS FULL BIT

The signal is output in digital full bit without including
the head margin. The SWFR signal is output but not in SWFR
digital full bit.
Reference data
INPUT: DVD ANALOG

Input level Volume
Both ch, -20 dBm -10 dB +16.9 dBm +27.2 dBm +27.2 dBm +27.2 dBm -1.3 dBm
YSS FULL BIT F YSS FULL BIT F

The front CH signal is output in digital full bit at the main CHCH
CH.
Reference data
INPUT: DVD ANALOG
Input level Volume
Both ch, -20 dBm -10 dB +16.9 dBm - - - -
DSP THROUGH ~
YSS (Analog)
( Digital Audio Data / PCM )
YSS L/R
RC/- C/LFE LS/RS L/R
CS49329
CS L/R
Analog A/D AD or CS L/R

L/R
C(L) C/SW
L/R
LFE Sp Config
DIR LS/RS (R) -/RC
RL/RR
(L/R) RL/RR
C/LFE
Digital L/R
(L/R) L/R
RC(R)
Main DSP Sub DSP
(Shaded items not used in this example)
21
2. RAM THROUGH 2. RAM THROUGH

The main L/R signal is output from Sub DSP of YSS938. Main L/RYSS938Sub DSP
The CT, RC, RL/RR, FL/FR signals are output through Sub CTRCRL/RRFL/FRSub DSP DRAM
DSP - DRAM.
RAM 0dB RAM 0dB
Reference data
INPUT: DVD ANALOG
Input level Volume
Both ch, -20 dBm -10 dB - +21.2 dBm - - -
RAM THROUGH ~
(Auto)
YSS L/ R
CS49329
CS L/R
* Each signal except the SW

C/SW
L/R signal passes through the
Same as DSP external DRAM.
DIR Through "YSS" LS/RS
-/RC
* The basic passage is
(automatic the same as DSP FL/FR
C/LFE
Digital selection) Through "YSS" L/R
(automatic selection)
Main DSP Sub DSP
4Mbit DRAM
22
3. PRO LOGIC 3. PRO LOGIC
PRO LOGIC I PRO LOGIC I
Reference data
INPUT: DVD ANALOG
Input level Volume
Each ch, -20 dBm -10 dB +17.0 dBm - - - -10.2 dBm
Both ch, -20 dBm -10 dB - +30.0 dBm - - -
PRO LOGIC II PRO LOGIC II
Reference data
INPUT: DVD ANALOG
Input level Volume
Both ch, -20 dBm -10 dB - +30.0 dBm - - -
The L/C/R/RL/RR signals undergo the Pro-Logic processing L/C/R/RL/RRYSS938C/

and C/RL/RR signals are output through Sub DSP-DRAM. RL/RRSub DSP-DRAMMAIN L/R
Sub DSP is selected for MAIN L/R output. Sub DSP
Using the sub-menu, it is possible to select PRO LOGIC I, PRO LOGIC Movie

II (Movie). The Auto Input Balance function is always off. Auto Input Balance off
When the Dolby Digital Multi input is used, the function is
AACCS49329L/R
the same as in the Dolby Digital Normal mode.
J model
The LFE signal is not output when decoding in the PRO
LOGIC I, II mode. Dolby Digital MultiDolby Digital Normal

PRO LOGIC LFE
Dolby Pro Logic (Auto)

dts/AAC
decode
YSS L/ R
CS49329
CS L/R

L/R
C C/SW
L/R
Sp Config
DIR DPL/PLII LS/RS
-/RC
decode RL/RR RL/RR

C/-
Digital
L/R L/R
Main DSP Sub DSP
4Mbit DRAM

23
Neo:6 Neo:6
Reference data
INPUT: DVD ANALOG
Input level Volume
Both ch, -20 dBm -10 dB - +30.0 dBm - - -
L/C/R/RL/RC/RR signals are NEO:6 processed by L/C/R/RL/RC/RRCS49329NEO:6C/

CS49329 and C/RL/RC/RR signals are output through Sub RL/RC/RRSub DSP-DRAMMAIN L/
DSP-DRAM. CS49329 is selected for the MAIN L/R output. R C S 4 9 3 2 9 N E O : 6
The NEO:6 mode is fixed to Cinema 6ch. Cinema 6ch
When DD/dts input is used, the signal is decoded by YSS- DD/dtsYSS-938L/RCS49329
938 and then L/R signal is NEO:6 processed by CS49329. NEO:6AAC
When AAC input is used, the signal is muted. When NEO:6 NEO:6LFE
decoding is used, the LFE signal is not output.
Neo:6 (Auto)
Neo:6
decode
YSS L/ R
RC/- C/- LS/RS L/R
CS49329
CS L/R

L/R
C C/SW
L/R
Sp Config
DIR DD/dts LS/RS
-/RC
decode
(/Through) C/LFE
RL/RR RL/RR
Digital
L/R L/R
RC
Main DSP Sub DSP
4Mbit DRAM
24
4. SPEAKERS SET 4. SPEAKERS SET

The input signal is automatically identified and switched in dts DOLBY DIGITAL AAC
the priority order of dts DOLBY DIGITAL AAC PCM PCM AUDIO A/D

AUDIO Analog (A/D) according to the signal detection.
The signals output from the DSP block are the same as 1. DSPNo.1 DSP THROUGHYSS 0dB
DSP THROUGH: YSS 0dB.
MAIN: SMALL 0dB CENTER: NONE LFE/BASS: MAIN
Front Mix: 5ch Rear Center power Tone Control Flat
Tone Control +10dB Tone Control 10dB
The analog switch settings for each sub-menu are as shown

in the table below.
Sub-menu CENTER SP REAR SP MAIN SP MAIN LEVEL LFE/BASS

1 MAIN: SMALL 0dB LARGE LARGE SMALL 0dB SWFR
2 CENTER: NONE NONE LARGE LARGE 0dB BOTH
3 LFE/BASS: MAIN SMALL SMALL LARGE 0dB MAIN
4 FRONT MIX: 5CH LARGE LARGE LARGE 0dB BOTH
5 REAR CENTER: POWER LARGE LARGE LARGE 0dB BOTH
LARGE: This mode is used with a speaker with high LARGE

bass reproduction performance (a large unit).
Full bandwidth signals are output.
SMALL: This mode is used with a speaker with low SMALL
bass reproduction performance (a small unit). 90HzLFE/
The signals of 90 Hz or less are mixed into B A S S
the channel specified by LFE/BASS.
NONE: This mode is used with no center speaker. NONE
The center content is reduced by 3 dB and -3dBMAIN L/R
distributed to MAIN L/R.
Sub-menu Treble Bass

6 Tone Control Flat 0 dB 0 dB
7 Tone Control +10dB +10 dB +10 dB
8 Tone Control 10dB 10 dB 10 dB
25
Reference data
INPUT: DVD ANALOG (Both ch)

Sub-menu Input level Volume
1 MAIN: SMALL 0dB 1 kHz Both ch, -20 dBm -10 dB +17.0 dBm - - - -
2 CENTER: NONE 1 kHz Both ch, -20 dBm -10 dB +13.7 dBm +27.0 dBm - - -
3 LFE/BASS: MAIN 50 Hz Both ch, -20 dBm -10 dB - - - - +6.9 dBm
4 Front Mix: 5ch 1 kHz Both ch, -20 dBm -10 dB +17.0 dBm - - - -
5 Rear Center Power 1 kHz Both ch, -20 dBm -10 dB - - - +27.0 dBm -
6 Tone Control Flat 1 kHz Both ch, -20 dBm -10 dB +17.0 dBm +27.0 dBm +27.0 dBm +27.0 dBm -1.5 dBm
7 Tone Control +10dB 1 kHz Both ch, -20 dBm -10 dB +18.5 dBm +27.0 dBm +27.0 dBm +27.0 dBm -1.5 dBm
8 Tone Control -10dB 1 kHz Both ch, -20 dBm -10 dB +15.4 dBm +27.0 dBm +27.0 dBm +27.0 dBm -1.5 dBm
5. HEADPHONE TEST 5. HEADPHONE TEST

The signal is output including the head margin.
MAIN 12dB MARGIN MAIN 12dB MARGIN
Reference data
INPUT: DVD ANALOG
Input level Volume
Each ch, -20 dBm -10 dB +16.8 dBm - - - -
MAIN 15dB MARGIN MAIN 15dB MARGIN
Reference data
INPUT: DVD ANALOG
Input level Volume
Both ch, -20 dBm -10 dB +19.5 dBm - - - -
YSS L/R
CS49329
CS L/R
C/SW
Same as L/R Same as
DIR "1. YSS" LS/RS
"1. YSS" -/RC
(automatic (automatic
RL/RR
Digital selection) C/LFE selection)

L/R
Main DSP Sub DSP

26
6. OTHER INPUT 6. OTHER INPUT

The signal input through the 6CH INPUT terminals is output. 6CH
(Not applied to this model.)
EXTERNAL DECODER EXTERNAL DECODER
7. DISPLAY CHECK 7. DISPLAY CHECK

This program is used to check the FL display section. The FL
display condition varies as shown below according to the
sub-menu operation. The signals are processed using EFFECT OFFANALOG MAIN BYPASSL/R
EFFECT OFF (The L/R signal is output using ANALOG
MAIN BYPASS.)
Initial display / All segments OFF / All segments ON (dimmer 100%) /

100%
Lighting of segments All segments ON (dimmer 50%) /
Lighting in lattice /
in lattice / 50%

Short / Normal /
Segment conditions of the FL driver and the FL tube are FLFL

checked by turning ON and OFF all segments. Next, the
operation of the FL driver is checked by using the dimmer FL
control. Then a short between segments next to each other
is checked by turning ON and OFF all segments alternately
/
(in lattice). (In the above example, the segments in the
second row from the top are shorted.)
27
8. MANUAL TEST 8. MANUAL TEST

The noise generator built into the DSP outputs the test noise DSP
through the channels specified by the sub-menu.
The noise frequency for LFE is 35 to 250 Hz. Other than LFE35250Hz
that, the center frequency is 800 Hz. 800Hz
TEST ALL TEST MAIN L TEST CENTER
Noise is output from all channels. Noise is output from the MAIN L channel. Noise is output from the CENTER
MAIN L channel.
CENTER
TEST MAIN R TEST REAR R TEST REAR CENTER
Noise is output from the MAIN R channel. Noise is output from the REAR R channel. Noise is output from the REAR C channel.
MAIN R REAR R REAR C
TEST REAR L TEST LFE
Noise is output from the REAR L Noise is output from the SUB WOOFER
channel. channel.
REAR L SUB WOOFER
9. FACTORY PRESET 9. FACTORY PRESET

This menu is used to reserve and inhibit initialization of the RAM
back-up RAM. The signals are processed using EFFECT /
OFF. (The L/R signal is output using ANALOG MAIN EFFECT OFF
ANALOG MAIN BYPASS
BYPASS.) L/R
PRESET INHIBIT (Initialization inhibited) / PRESET INHIBIT

RAM initialization is not executed. Select this sub-menu to protect the values set by the user.
RAM
PRESET RESERVED (Initialization reserved) / PRESET RESERVED

Initialization of the back-up RAM is reserved. (Actually, initialization is executed the next time
that the power is turned on.) Select this sub-menu to reset to the original factory settings or to
reset the RAM.
RAM
RAM
CAUTION: Before setting to the PRESET RESERVED, PRESET RESERVED

write down the existing preset memory content
of the Tuner in a table as shown below. (This
is because setting to the PRESET RESERVED
will cause the user memory content to be
erased.)
Preset group P1 P2 P3 P4 P5 P6 P7 P8
28
PRESET STATIONS /
STATION FM FACTORY PRESET DATA (MHz) STATION AM FACTORY PRESET DATA (kHz)
PAGE NO. U, C R, T, K, A, B, G, L J PAGE NO. U, C, R, T, K A, B, G, L J
1 87.5 87.5 76.0 1 630 630 630
2 90.1 90.1 83.0 2 1080 1080 1080
3 95.1 95.1 84.0 3 1440 1440 1440
4 98.1 98.1 86.0 4 530 531 531
A/C/E B/D
5 107.9 108.0 90.0 5 1710 1611 1611
6 88.1 88.1 78.0 6 900 900 900
7 106.1 106.1 88.0 7 1350 1350 1350
8 107.9 108.0 82.1 8 1400 1404 1404
10. AD DATA CHECK/FAN TEST 10. AD DATA CHECK/FAN TEST

This menu is used to display the A/D conversion value of A/D
the terminals which detects panel keys of the main unit %
and protection functions in % using the sub-menu. During
signal processing, the condition before execution is K0/K1
maintained.
When K0/K1 menu is selected, keys become non-operable VOLUME
due to detection of the values of all keys. However, it is 2
possible to advance to the next sub-menu by turning the
VOLUME of the main unit while in the menu select mode.

When using this function, note that turning the VOLUME
more than 2 clicks will cause the volume value to change.
* The figures in the diagram are given as reference only.
DC (protection detection) DC
DC protection value (Normal value: 26 to 46) U, C, A, L, DC 2646
R, T, K models DC
(Normal value: 42 to 68) B, G models
If DC is out of the normal value range, the protection function
works to turn off the power.
UC (Detected value of D-AMP module temperature) UCD-AMP

The ambient temperature of the D-AMP module is detected D-AMPTH661
by TH661. 5V059
The voltage is displayed in % using the detected value of
the temperature. The reference voltage is 5V. (Normal
value: 0 to 59)
THM/Fan (temperature detection/fan drive level) THM/Fan/

THM: 500% display of the voltage based on the THM: 5005V
temperature detected value. Reference voltage : 5V 0272
(Normal value: 0 to 272) Fan:
Fan: Current fan drive level on the left and the past fan
drive history on the right.
5 levels from 0 to 4
045
REC-OUT REC-OUT
Not applied to this model.
29
IMP SW (Impedance) IMP SW

Not applied to this model.
K0/K1 (Panel key of main unit) K0/K1

A/D of the key fails to function properly when the standard A / D
value is deviated. In this case, check the constant of partial Table 1
pressure resistor, solder condition, etc. Refer to table 1.
[Table 1]
Display (%) K0 K1
0-5 ENTER
6 - 15 INPUT
15 - 28 DSP
28 - 46 TUNER
FAN DRIVE TEST (For models so equipped) FAN DRIVE TEST

HIGH HIGH

MID MID

LOW LOW
30
11. IF STATUS (Input function status) 11. IF STATUS

Using the sub-menu, the status data is displayed one after 16
another in the hexadecimal notation.
During signal processing, the status before execution of
this menu is maintained.

* Numeric values in the figure example are for reference.
IS1, 2 (Internal status): IS 1, 2:

Indicates the status information of the microprocessor.
5th byte
4th byte 3rd byte
3rd byte 2nd byte
2nd byte 1st byte
1st byte
<1st byte> Digital input/output setting value 1

Upper 4 bits: REC OUT selected / 4bit REC OUT /
lower 4 bits: INPUT selected 4bit INPUT
Value Choice Preset name Value Choice Preset name

0 NONE 4 OPTD
1 OPTA VIDEO2 6 OPTF
2 OPTB DVD/CD 8 COAXA VIDEO1
3 OPTC DTV/CBL 9 COAXB
<2nd byte> Fs information of reproduction signal 2Fs
Display 00 01 02 03 04 05 06 0A 0B 0C 0D
Fs (kHz) Analog 32 44.1 48 64 88.2 96 Unknown NRM Unknown DBL Unknown QUAD Not defined
<3rd byte> Audio code mode information of reproduction 3

signal
Display 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D
Audio Code 1+1 1/0 2/0 3/0 2/1 3/1 2/2 3/2 2/3 3/3 OVER 6.1 MULTI MONO MULTI PCE Unknown
<4th byte> Format information of reproduction signal 4

*1: Analog processing used for digital reproduction is not *1: 4ch
possible because of a commercial bit or 4-ch audio
reason.
Display Signal format
00 Analog (Unlock)
01 Incorrect digital (*1)
10 PCM Audio
20 Digital Data
21 IEC1937 Data
22 None PCM
23 Unknown
50 dts
51 Red dts
54 dts-ES MATRIX
58 dts-ES DISCRETE
5C dts-ES (Both flag)
60 AAC
C0 Dolby Digital
C1 D.D. Karaoke
C4 D.D.6.1 (D.D.EX)
31
<5th byte> Signal processing status information 5

*2: With digital signals other than 32 kHz, 44.1 kHz and 48 *2: 32kHz44.1kHz48kHz
kHz, through processing method is used for
reproducible signals.
bit7 MUTE request bit3

bit6 Red dts flashing bit2 Through & bypass (*2)
bit5 6.1/EX processing bit1
bit4 FULL MUTE (ON: 1) bit0 dts analog mute
CS1-5: Indicates channel status information of the input CS 1-5: IEC60958

signal (IEC60958).
BY1-4: Indicates information of the bit stream included in BY1-4: DOLBY DIGITAL
the DOLBY DIGITAL signal.
BS1-5: Indicates information of the bit stream included in BS1-5: dts

the dts signal.
YS1-3: Indicates device status information of YSS938 YS1-3: YSS938IC601

(IC601).
* The numeric value in the figure is an example for
reference.
Byte No. Function Byte No. Function Byte No. Function

1 YSS MUTE Reg 1 IEC 1937 Preamble Pc 1 DIR Status
2 YSS MODE Reg 2 Data Stream Reg 2 DIR fs
3 YSS IPORT BIT 7-0 3 Status Reg 3 DIR fs count
4 YSS IPORT BIT 14-8 4 YSS ZERO Reg 4 YSS ZEROBF
5 YSS OPORT 5 MIREG
SD: CS49329 Unsolicited Messages SD: CS49329 Unsolicited Messages

(AUTODETECT_RESPONSE) (AUTODETECT_RESPONSE)
MTT: Mute Trigger MTT: Mute Trigger
Byte No. Function

1 Mute condition
2 Factor of the last mute
3 Error count of YSS938-FSCNT
4 Mute count by YSS938-FSCNT
5 Error factor of down load of CS49329
32
12. DSP RAM CHECK 12. DSP RAM CHECK

This menu is used to self-diagnose whether or not the bus YSS938RAM
connection for the YSS938 and the external RAM is made
properly.
During signal processing, the status before execution of
this menu is maintained. NoEr
The address bus and the data bus are checked and the
connection condition is displayed.
When no error is detected, "NoEr" appears on display.
YSS938 BUS CHECK YSS938 BUS CHECK
Display Description
WAIT Bus is being checked.
NoEr No error detected.
DATA Data bus shorted or open.
RSCS /RAS or /CAS shorted, or open.
ADDR Address bus shorted or open.
PLD/SRAM BUS CHECK PLD/SRAM BUS CHECK
Display Description
WAIT Bus is being checked.
NoEr No error detected.
EDxx Data bus shorted or open. (XX: 00-07)
EAxx Address bus shorted or open. (XX: 00-0E)
13. SD DL CODE 13. SD DL CODE

This menu is used to display the data version of the FLASH 2ndFLASH ROMTOC
ROM, TOC information and sum calculated value for the
second decoder.
RDV RDV
Displays the data version.
TA 0-5 TA 0-5
Displays the TOC information. TOC
SA 0-5 SA 0-5
Displays the sum calculated value.
33
14. SOFT SW 14. SOFT SW

This menu is used to switch the function settings on P.C.B. P.C.B.
through the software so as to activate the product.
The protection function follows the P.C.B. settings. When P.C.B.AC
connected to AC or in the maker preset state, the unit is P.C.B.
initialized to the P.C. B. setting. Display of each function P.C.B.
after initialization varies depending on settings on P.C.B. DSPSW
The operation mode can be changed by selecting the sub- SOFT
menu and then using the DSP key. With SOFT selected
for the SW mode, the settings become effective.
SW MODE: PCB or SOFT can be selected. SW MODEPCBSOFT
MODEL SETTING: SL100 MODEL SETTINGSL100
DESTINATION: J, AT, UC, L, K, GB, none or R can be DESTINATIONJATUCLKGBnoneR

selected.
RDS: NOT or EXIST are displayed. RDSNOTEXIST
ZONE2: NOT ZONE2NOT

VIDEO FORMAT: NTSC or PAL are displayed. VIDEO FORMATNTSCPAL
34
15. MICROPROCESSOR INFORMATION 15.

The version, checksum and the port specified by the 4
microprocessor are displayed. The signal is processed
using EFFECT OFF. The checksum is obtained by adding
the data at every 8 bits for each program area and OFF
expressing the result as a 4-figure hexadecimal data. 8416

Version /
Release 1 digit / Main version 2 digit / DSP version 2 digit / GUI version 2 digit
Checksum /
A: All area
Check of port setting for judging microprocessor function

Display of AAC function detection port state

AAC
*1
PORT:0 0 0 0 0 x x x
Dest 0 Dest 1 Dest 2 Dest AM/FM Video Format
bit 7 6 5 4 3 2 1 0
0 0 0 J 531-1611 kHz / 9 kHz NTSC
76.0-90.0 MHz / 100 kHz
0 1 0 U, C 530-1710 kHz / 10 kHz NTSC
87.5-107.9 MHz / 200 kHz
Dest 0 (*1) 1 0 0 A, T 531-1611 kHz / 9 kHz PAL
Dest 1 (*1) 87.5-108.0 MHz / 50 kHz
Dest 2 (*1) 0 0 1 K 531-1611 kHz / 9 kHz NTSC
87.5-108.0 MHz / 50 kHz
1 0 1 G, B 531-1611 kHz / 9 kHz PAL
87.5-108.0 MHz / 50 kHz
1 1 0 L 530-1710 kHz / 10 kHz PAL
87.5-108.0 MHz / 100 kHz
1 1 0 531-1611 kHz / 9 kHz
87.5-108.0 MHz / 50 kHz
1 1 1 R 530-1710 kHz / 10 kHz NTSC
87.5-108.0 MHz / 100 kHz
1 1 1 531-1611 kHz / 9 kHz
87.5-108.0 MHz / 50 kHz
D-AMP MODULE TROUBLESHOOTING / D-AMP

When the D-AMP module is working properly, the sine wave D-AMP
signal appears at the speaker terminal in the no signal 400kHz200mVRMSDC
applied state. The sine wave signal is about 400kHz, about 50mV
200mVRMS and lower than DC offset 50mV based on the D-AMP
negative (-) side. When this signal is not observed, it is D-AMP
possible that the D-AMP module has failed. In such case,
replace the D-AMP module.
35
AMP ADJUSTMENT /
Condition
Start adjustment 5 sec or more after the power is turned 5
on.
Headphones are not plugged in.
No input signal.
Equipment required
Screwdriver with angled shank as shown below L
10 mm
DC Offset Adjustment DC
Adjust the potentiometer on each D-Amp Module so that DC010mV
the DC voltage becomes 0 10 mV at each speaker output. D-VR
SURROUND L SURROUND BACK FRONT L

SURROUND R CENTER FRONT R
36
DISPLAY DATA
V101 : HNA-16SM08T (WB569700) ANODE CONNECTION
55 16G 15G 14G 13G~1G

1
P1 V1 1-1 1-1
P2 V2 2-1 2-1
PATTERN AREA P3 V3 3-1 3-1
P4 V4 4-1 4-1
P5 V5 5-1 5-11
56 110
P6 V6 1-2 1-2
P7 V7 2-2 2-2
P8 V8 3-2 3-2
PIN CONNECTION P9 V9 4-2 4-2
PIN NO. 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 P10 5-2 5-2

P11 1-3 1-3
CONNECTION NP NP NP NP NP NP NP NP NX 15G 14G 13G 12G 11G 10G 9G 8G 7G 6G 5G 4G 3G 2G 1G NP NP F1 F1
P12 2-3 2-3
PIN NO. 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 P13 3-3 3-3
P14 4-3 4-3
CONNECTION F2 F2 NP NP P24 P25 P26 P27 P28 P29 P30 P31 P32 P33 P34 P35 P36 P37 P38 NP NP NP NP NP NP NP NP
P15 5-3 5-3
PIN NO. 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 P16 1-4 1-4
CONNECTION F2 F2 NP NP P23 P22 P21 P20 P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 NP NP NP NP NP NP NP NP P17 S1 2-4 2-4
P18 3-4 3-4
PIN NO. 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110
P19 S2 4-4 4-4
CONNECTION NP NP NP NP NP NP NP NP NP NP NP NP NP NP NP NX P8 P7 P6 P5 P4 P3 P2 P1 NP NP F1 F1 P20 5-4 5-4
Note : 1) F1, F2 ..... Filament 2) NP ..... No pin 3) NC ..... No connection 4) NX ..... No extened 5) 1G ~ 16G ..... Grid 6) P1 ~ 38 ..... Anode P21 S3 1-5 1-5
P22 2-5 2-5
P23 S4 3-5 3-5
P24 4-5 4-5
GRID ASSIGNMENT
16G 15G P25 S5 5-5 5-5
P26 1-6 1-6
P27 S6 2-6 2-6
P28 3-6 3-6
P29 4-6 4-6
1G 2G 3G 4G 5G 6G 7G 8G 9G 10G 11G 12G 13G 14G P30 5-6 5-6
1-1 2-1 3-1 4-1 5-1
P31 1-7 1-7
V1 V3 V5 V7
1-2 2-2 3-2 4-2 5-2 P32 2-7 2-7
1-3 2-3 3-3 4-3 5-3 P33 3-7 3-7
1-4 2-4 3-4 4-4 5-4 P34 4-7 4-7
1-5 2-5 3-5 4-5 5-5 V2 V4 V6 V8 S1 S2 S3 P35 5-7 5-7
1-6 2-6 3-6 4-6 5-6 P36
1-7 2-7 3-7 4-7 5-7 S4 S5 S6 P37
V9
P38
(1G~14G) (15G) (16G)
37
IC DATA IC304: YSS938 (DIGITAL P.C.B)

DSP
IC304: YSS938 (DIGITAL P.C.B)
OVFB/END
KARAOKE
ZEROFLG
NONPCM
DTSDATA
AC3DATA
SURENC
TESTXO
RAMA17
RAMA16
RAMA15
RAMA14
RAMA13
RAMA12
RAMA11
RAMA10
TESTXI
No. Name I/O Function
DIRINT
/LOCK
MUTE
SELI2
SELI3
SELI4
SELI5
SELI6
SELI7
SELI8
DSP
VDD2
VDD1
VDD2
IPINT
CRC
SCK
VSS
VSS
VSS
/CS
SO
/IC
SI
1 XO O Crystal oscillator connecting terminal
2 XI I Crystal oscillator connecting terminal (24.576MHz)
160
159
158
157
156
155
154
153
152
151
150
149
148
147
146
145
144
143
142
141
140
139
138
137
136
135
134
133
132
131
130
129
128
127
126
125
124
123
122
121
XO 1 120 RAMA9 3 SELI1 I+ Built-in selector input 1 (Unconnected) (AXD)
XI 2 119 RAMA3
SELI1 3 118 RAMA4 4 SELI0 I+ Built-in selector input 0 (GND)
SELI0 4 117 SELI9
SELOA 5 116 SELI10 5 SELOA O+ Built-in selector output A (ISEL)
SELOB 6 115 SELI11
TESTMS 7 114 SELI12
6 SELOB O+ Built-in selector output B (Unconnected) (RSEL)
TESTXEN 8 113 SELI13 7 TESTMS I+ Test terminal (Unconnected)
IPORT0 9 112 RAMA2
IPORT1 10 111 RAMA5 8 TESTXEN I+ Test terminal (Unconnected)
IPORT2 11 110 RAMA1
IPORT3 12 109 RAMA6 9 IPORT0 I+ General purpose input terminal (CXDTA)
IPORT4 13 108 RAMA0
DDIN0 14 107 RAMA7 10 IPORT1 I+ General purpose input terminal (CXDTB)
DDIN1 15 106 RAMA8
DDIN2 16 105 VDD1 11 IPORT2 I+ General purpose input terminal
DDIN3 17 104 VSS
VSS 18 103 RASN
12 IPORT3 I+ General purpose input terminal
CPO 19 102 RAMOEN 13 IPORT4 I+ General purpose input terminal
AVDD
DIRPCO
DIRPRO
20
21
22
YSS938 101
100
99
RAMWEN
CASN
RAMD15
14 DDIN0 Is DIR: Digital audio interface data input terminal 0 (ISEL)
AVSS 23 98 RAMD14 15 DDIN1 Is DIR: Digital audio interface data input terminal 1/General purpose input terminal (Pull down)
TESTBRK 24 97 RAMD13
TESTR1 25 96 RAMD12 16 DDIN2 Is DIR: Digital audio interface data input terminal 2/General purpose input terminal (Pull down)
TESTR2 26 95 RAMD11
VDD1 27 94 RAMD10 17 DDIN3 Is DIR: Digital audio interface data input terminal 3/General purpose input terminal (Pull down)
SDWCKI0 28 93 RAMD9
SDBCKI0 29 92 RAMD8
18 VSS Ground terminal
/SDBCKO 30 91 VDD1 19 CPO A PLL filter connecting terminal
IPORT8 31 90 VSS
IPORT9 32 89 RAMD7 20 AVDD +3.3V power terminal (for DIR)
IPORT10 33 88 RAMD6
IPORT11 34 87 RAMD5 21 DIRPCO A DIR: PLL filter connecting terminal
SDIA 35 86 RAMD4
SDOA2 36 85 ZEROBF0L 22 DIRPRO A DIR: PLL filter connecting terminal
SDOA1 37 84 ZEROBF0R
SDOA2 38 83 ZEROBF1L 23 AVSS Ground terminal (for DIR)
SDIB3 39 82 ZEROBF1R
SDIB2 40 81 RAMD3
24 TESTBRK I+ Test terminal (Unconnected)
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
25 TESTR1 I+ PLL initialization signal input terminal for DSP (/ICD)
26 TESTR2 I+ Test terminal (Unconnected)
SDIB1
SDIB0
VSS
VDD2
IPORT12
IPORT13
IPORT14
DIRSDO
DIRWCK
DIRBCK
DIRMCK
ERR/BS
SYNC/U
FS128/C
DBL/V
SDWCKI1
SDBCKI1
VSS
SDOB3
SDOB2
SDOB1
SDOB0
VDD1
ZEROBF3R
ZEROBF3L
ZEROBF2R
ZEROBF2L
OPORT0
OPORT1
OPORT2
OPORT3
OPORT4
OPORT5
OPORT6
OPORT7
VSS
VDD2
RAMD0
RAMD1
RAMD2
27 VDD1 +3.3V power terminal (for terminal section)
28 SDWCKI0 I+ Word clock input terminal for SDIA, SDOA, SDIB, SDOB interface (Unconnected) (WCKG)
ZEROBF3R-0L
29 SDBCKI0 I+ Bit clock input terminal for SDIA, SDOA, SDIB, SDOB interface (Unconnected) (BCKG)
OVFB/END
RAMD0-15
RAMA0-17
KARAOKE
ZEROFLG
DTSDATA
AC3DATA
RAMWEN
NONPCM
RAMOEN
SURNEC
DIRSDO
DIRPRO
DIRPCO
30 /SDBCK0 O DIRBCK or SDBCKI0 invert clock output terminal (Unconnected)
SDOA2
SDOA1
SDOA0
SDIB3
SDIB2
SDIB1
SDIB0
MUTE
RASN
CASN
SDIA
CPO
CRC
31 IPORT8 I+ IPINT general purpose input terminal

XO
XI
32 IPORT9 I+ IPINT general purpose input terminal (NONPCM)

33 IPORT10 I+ IPINT general purpose input terminal (NONPCM)
DSP Clock
(30 MHz)
External
Clock at DIR
OVFSEL 34 IPORT11 I+ IPINT general purpose input terminal (MUTE)

(25 MHz)
Memory /LOCK
CRC
PLL
PLL
Interface 35 SDIA I AC-3/DTS bit stream (or PCM) data input terminal to Main DSP (SDIA)
DBL
36 SDOA2 O PCM output terminal from Main DSP (C/LFE output) (Unconnected)
VMOD
END
OVFB
SDOB3 37 SDOA1 O PCM output terminal from Main DSP (LS/RS output) (Unconnected)
(AC-3/ProLogic/DTS Decoder)
DBL/V
C, LFE
SDOB Interface
V
SDDA Interface
38 SDOA0 O PCM output terminal from Main DSP (L/R output)

SDIB Interface
SDIA Interface
DIRO Interface
Main DSP
SDIASEL
SDOB2
Sub DSP
39 SDIB3 I+ PCM input terminal 3 to Sub DSP

LS, RS
SDIBSEL
BSMOD
ERR
ERR/BS 40 SDIB2 I+ PCM input terminal 2 to Sub DSP
SDOB1 BS
41 SDIB1 I+ PCM input terminal 1 to Sub DSP
L, R
SDOB0 42 SDIB0 I+ PCM input terminal 0 to Sub DSP

DDIN3
DDINSEL
43 VSS Ground terminal

7
DDIN2
DIR
SDOBCKSEL SDIBCKSEL 44 VDD2 +2.5V power terminal (for internal circuit)

6
DDIN1
SDIACKSEL
DDIN0 45 IPORT12 I+ IPINT general purpose input terminal (DIRINT)

SDWCKI1
46 IPORT13 I+ IPINT general purpose input terminal (DBL)
DIRINT
SDBCKI1 47 IPORT14 I+ IPINT general purpose input terminal (DBL)
Control Signals
UMOD
SYNC
SYNC/U 48 DIRSDO O AC-3/DTS bit stream (or PCM) data output terminal from DIR
Coefficient, Control Register U
IPORT5-7
MPLOAD
Program
49 DIRWCK O DIR: Serial data word clock (fs) output terminal (WCK)
RAM 50 DIRBCK O DIR: Serial data bit clock (64fs) output terminal (BCK)
CMOD
SELOA -COM Interface FS128

FS128/C 51 DIRMCK O DIR: Serial data master clock (256fs or 128fs) output terminal (MCK)
SELOB C
SELB SELA 52 ERR/BS O DIR: Data error detect output/block start output terminal (Unconnected)
53 SYNC/U O DIR: Serial data synchronous timing output/user data output terminal (Unconnected)
54 FS128/C O DIR: Serial data master clock 128fs output/channel status output terminal (Unconnected) (FS128)
SELI0-13
OPORT0-7
SCK
SI
So
/cs
IPINT
IPORT8-14
IPORT0-4
/SDBCKO
SDWCKI0
SDBCKI0
DIRWCK
DIRBCK
DIRMCK
55 DBL/V O DIR: Double rate clock output/validity flag output terminal (DBL)
38
IC304: YSS938 (DIGITAL P.C.B) IC304: YSS938 (DIGITAL P.C.B)

DSP DSP
No. Name I/O Function No. Name I/O Function
56 SDWCKI1 I+ Word clock input terminal for SDIB, SDOB interface (Unconnected) (WCKG) 111 RAMA5 O Sub DSP: External memory address terminal 5
57 SDBCKI1 I+ Bit clock input terminal for SDIB, SDOB interface (Unconnected) (BCKG) 112 RAMA2 O Sub DSP: External memory address terminal 2
58 VSS Ground terminal 113 SELI13 I+ Built-in selector input 13 (Unconnected)
59 SDOB3 O PCM output terminal from Sub DSP 114 SELI12 I+ Built-in selector input 12 (Unconnected)
62 SDOB0 O PCM output terminal from Sub DSP 117 SELI9 I+ Built-in selector input 9 (Unconnected) (CXB)
63 VDD1 +3.3V power terminal (for terminal section) 118 RAMA4 O Sub DSP: External memory address terminal 4
64 ZEROBF3R O+ SDOB3 Rch zero flag output terminal (Unconnected) (ZF3R) 119 RAMA3 O Sub DSP: External memory address terminal 3
65 ZEROBF3L O+ SDOB3 Lch zero flag output terminal (Unconnected) (ZF3L) 120 RAMA9 O Sub DSP: External memory address terminal 9 (Unconnected)
66 ZEROBF2R O+ SDOB2 Rch zero flag output terminal (Unconnected) (ZF2R) 121 RAMA10 O Sub DSP: External memory address terminal 10 (Unconnected)
67 ZEROBF2L O+ SDOB2 Lch zero flag output terminal (Unconnected) (ZF2L) 122 RAMA11 O Sub DSP: External memory address terminal 11 (Unconnected)
68 OPORT0 O General purpose output terminal (/RINH1) 123 VSS Ground terminal
69 OPORT1 O General purpose output terminal (/RINH2) 124 VDD2 +2.5V power terminal (for internal circuit)
70 OPORT2 O General purpose output terminal (/ICDA) 125 SELI8 I+ Built-in selector input 8 (CXA)
71 OPORT3 O General purpose output terminal (Unconnected) (/ICAD) 126 SELI7 I+ Built-in selector input 7 (GND)
72 OPORT4 O General purpose output terminal (DPS) 127 SELI6 I+ Built-in selector input 6 (Unconnected) (OPTF)
73 OPORT5 O General purpose output terminal (Unconnected) (RST) 128 SELI5 I+ Built-in selector input 5
74 OPORT6 O General purpose output terminal (Unconnected) (ERROR) 129 RAMA12 O Sub DSP: External memory address terminal 12 (Unconnected)
75 OPORT7 O General purpose output terminal (/PRST) 130 RAMA13 O Sub DSP: External memory address terminal 13 (Unconnected)
76 VSS Ground terminal 131 RAMA14 O Sub DSP: External memory address terminal 14 (Unconnected)
77 VDD2 +2.5V power terminal (for internal circuit) 132 RAMA15 O Sub DSP: External memory address terminal 15 (Unconnected)
78 RAMD0 I+/O Sub DSP: External memory data terminal 0 133 RAMA16 O Sub DSP: External memory address terminal 16 (Unconnected)
79 RAMD1 I+/O Sub DSP: External memory data terminal 1 134 RAMA17 O Sub DSP: External memory address terminal 17 (Unconnected)
80 RAMD2 I+/O Sub DSP: External memory data terminal 2 135 OVFB/END O Sub DSP: Overflow/program end detect terminal (Unconnected)
81 RAMD3 I+/O Sub DSP: External memory data terminal 3 136 ZEROFLG O Main DSP: Zero flag output terminal (Unconnected)
82 ZEROBF1R O+ SDOB1 Rch zero flag output terminal (Unconnected) (ZF1R) 137 VSS Ground terminal
83 ZEROBF1L O+ SDOB1 Lch zero flag output terminal (Unconnected) (ZF1L) 138 NONPCM O Main DSP: Non-PCM data detect terminal
84 ZEROBF0R O+ SDOB0 Rch zero flag output terminal (Unconnected) (ZF0R) 139 DTSDATA O Main DSP: DTS data detect terminal (Unconnected)
85 ZEROBF0L O+ SDOB0 Lch zero flag output terminal (Unconnected) (ZF0L) 140 AC3DATA O Main DSP: AC3 data detect terminal (Unconnected)
86 RAMD4 I+/O Sub DSP: External memory data terminal 4 141 MUTE O Main DSP: Auto mute detect terminal
87 RAMD5 I+/O Sub DSP: External memory data terminal 5 142 KARAOKE O Main DSP: AC3 KARAOKE data detect terminal (Unconnected)
88 RAMD6 I+/O Sub DSP: External memory data terminal 6 143 VDD1 +3.3V power terminal (for terminal section)
89 RAMD7 I+/O Sub DSP: External memory data terminal 7 144 SURENC O Main DSP: AC-3 2/0 mode Dolby surround encode input detect terminal (Unconnected)
90 VSS Ground terminal 145 CRC O Main DSP: AC3 CRC error detect terminal (Unconnected)
91 VDD1 +3.3V power terminal (for terminal section) 146 /LOCK O DIR: PLL lock detect terminal (Unconnected)
92 RAMD8 I+/O Sub DSP: External memory data terminal 8 147 DIRINT O DIR: Interrupt output terminal
93 RAMD9 I+/O Sub DSP: External memory data terminal 9 148 /CS Is Microprocessor interface chip select input terminal (/CSY)
94 RAMD10 I+/O Sub DSP: External memory data terminal 10 149 SO Ot Microprocessor interface data output terminal (SDDY)
95 RAMD11 I+/O Sub DSP: External memory data terminal 11 150 SI Is Microprocessor interface data input terminal (SDMYB)
96 RAMD12 I+/O Sub DSP: External memory data terminal 12 151 SCK Is Microprocessor interface clock input terminal (SCKYB)
97 RAMD13 I+/O Sub DSP: External memory data terminal 13 152 /IC Is Initial clear input terminal (/ICYP)
98 RAMD14 I+/O Sub DSP: External memory data terminal 14 153 IPINT O+ Interrupt output terminal by IPORT 8-14
99 RAMD15 I+/O Sub DSP: External memory data terminal 15 154 SELI4 I+ Built-in selector input 4 (Unconnected) (OPTD)
100 CASN O Sub DSP: Column address strobe output terminal for external DRAM 155 VSS Ground terminal
101 RAMWEN O Sub DSP: Write enable terminal for external memory 156 SELI3 I+ Built-in selector input 3 (OPTC)
102 RAMOEN O Sub DSP: Output enable terminal for external memory 157 SELI2 I+ Built-in selector input 2 (OPTB)
103 RASN O Sub DSP: Low address strobe output terminal for external DRAM 158 TESTXI I Test terminal (should be always connected to VSS)
104 VSS Ground terminal 159 TESTXO O Test terminal (Unconnected)
105 VDD1 +3.3V power terminal (for terminal section) 160 VDD2 +2.5V power terminal (for internal circuit)
106 RAMA8 O Sub DSP: External memory address terminal 8
Is: Schmidt trigger input terminal
I+: Input terminal with pull-up resistor
110 RAMA1 O Sub DSP: External memory address terminal 1 O: Digital output terminal
Ot: 3-state digital output terminal
A: Analog terminal
39
IC307: M30805SGP (DIGITAL P.C.B) IC307: M30805SGP (DIGITAL P.C.B)

16bit -COM (Main CPU) 16bit -COM (Main CPU)
P121/CMOS/OUT/SCKP
P123/CMOS/OUT/SDTP
P124/CMOS/OUT/CEP
P122/CMOS/IN/SDRP
Pin Pin Name Type I/O Function Name Detail Of Function
P120/IN/SDRR
1 P96 TxD4 S-OUT dsp CST CS493x TxD
P15/D13/INT3
P16/D14/INT4
P17/D15/INT5
P12/D10
P13/D11
P14/D12
P32/A10
P33/A11
P34/A12
P35/A13
P36/A14
P37/A15
P40/A16
P41/A17
P42/A18
P43/A19
2 P95 CLK4 S-CLK dsp CSC CS493x CLOCK OUT (Necessary Pullup)
P11/D9
P20/A0
P21/A1
P22/A2
P23/A3
P24/A4
P25/A5
P26/A6
P27/A7
P30/A8
P31/A9
Vss
Vcc
Vss
Vcc
3 P94 DA1 DA-OUT amp FAN Fun Control D-A OUT [0~Vcc]
4 P93 (DA0) CTS3 f/gui CTS Flash ROM Write RS232C CTS [CTS]
5 P92 TxD3 S-OUT f/gui TXYDC Flash ROM Write YDC DATA OUT/RS232C TXD
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
108
107
106
105
104
103
102
101
100
P10/D8 109 72 P44/A20 6 P91 RxD3 S-IN f/gui RXYDC Flash ROM Write YDC DATA IN/RS232C RXD
P07/D7 110 71 P45/A21
7 P90 CLK3 S-CLK f/gui RTS Flash ROM Write YDC CLK/RS232C RTS
P06/D6 111 70 P46/A22
P05/D5 112 69 P47/A23 8 P146 CMOS IN uop VRB Rotary Encoder B IN (Necessary Pullup)
P04/D4 113 68 P125/IN/TUNDE
P114/CMOS/OUT/MSROOT 114 67 P126/CMOS/OUT/TMT
9 P145 CMOS IN uop VRA Rotary Encoder A IN (Necessary Pullup)
P113/CMOS/OUT/ICCDK 115 66 P127/IN/ST 10 P144 CMOS OUT amp FRMT Front Ch Mute L: Mute
P112/CMOS/IN/RDSE 116 65 P50/WRL/OUT
P111/CMOS/OUT/SCKR 117 64 P51/WRH/OUT 11 P143 CMOS OUT amp SRMT UCD Enable L: disable
P110/CMOS/OUT/SDTR 118 63 P52/RD/OUT
P03/D3 119 62 P53/BCLK
12 P142 CMOS OUT amp PRY Power Relay Output H: Relay ON
P02/D2 120 61 P130/CMOS/OUT 13 P141 CMOS OUT dsp /ICD YSS938 /CODEC /DEM OUT
P01/D1 121 60 P131/CMOS/OUT/CSPLD
P00/D0 122 59 Vcc 14 P140 CMOS OUT dsp CSY YSS938 CE OUT
P157/CMOS/OUT/VIB 123 58 P132/CMOS/OUT/ICCS
15 BYTE - - bus Connect to VSS(GND) (Select 16bit Bus)
P156/CMOS/OUT/VIA 124 57 VSS
P155/CMOS/OUT/NTSC 125 56 P133/CMOS/OUT/CSCS 16 CNVSS - - Connect to Vcc (+5V) Through Resistor (2.2 ohms)
P154/CMOS/OUT/CMT
P153/CMOS/OUT/SWMIX
126
127 M30805SGP 55
54
P54/HLDA
P55/HOLD
17 P87 - IN BT232 Write in RS232C Boot H: Boot (Necessary Pulldown)
P152/CMOS/OUT/CMIX 128 53 P56/ALE 18 P86 - IN BTYDC Write in YDC Boot L: Boot (Necessary Pulldown)
P151/CMOS/OUT/GAIN 129 52 P57/RDY/IN
Vss 130 51 P134/CMOS/OUT/HPMT 19 /RESET - - RESET [L: RESET]
P150/CMOS/IN/PRI 131 50 P135/CMOS/OUT/STBY
Vcc 132 49 P136/CMOS/OUT/CKBD
20 XOUT - - 20MHz OUT (Include Feedback Resistor)
P107/AN7/OUT/MTSW 133 48 P137/CMOS/OUT/DTBD 21 VSS - - GND
P106/AN6/A-D IN/UCDTHM 134 47 P60/CTS0/OUT/BLK
P105/AN5/A-D IN/PRD 135 46 P61/CLK0/S-CLK/CKFD 22 XIN - - 20MHz IN (Include Feedback Resistor)
45 P62/RXD0/IN/HP
P104/AN4/A-D IN/THM 136
23 VCC - - Power Supply (Back up) +5V
P103/AN3/IN/ACPRT 137 44 P63/TXD0/S-OUT/DTFD
P102/AN2/A-D IN/ADKEY0 138 43 P64/CTS1/OUT/VR1 24 P85 /NMI IN Connect to Vcc (+5V) Through Resistor (10 k-ohms) (NMI Function not in use)
P101/AN1/OUT/BINH 139 42 P65/CLK1/IN-OUT/UCDF
AVss 140 41 VSS
25 P84 /INT2 INT-IN dsp INT938 YSS938 IPINT/MUTE/DIR (INT) Down Edge
P100/AN0/A-D IN 141 40 P66/RxD1/OUT/VIC 26 P83 /INT1 INT-IN uop PSW Standby SW IN Up Edge
VREF 142 39 Vcc
AVcc 143 38 P67/TxD1/OUT/HPF 27 P82 /INT0 INT-IN uop REM1 Remo. Con. IN Down Edge
P97/RxD4/S-IN/CSR 144 37 P70/TxD2/S-OUT/SMD
28 P81 TA4IN IN amp PDET Power Down DETECT INT IN Down Edge
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
1
2
3
4
5
6
7
8
9
29 P80 TA4OUT IN XYDC When Bootup: Discriminate CLOCK for Bootup [L: 20MHz] (Necessary Pulldown)
30 P77 TA3IN IN-OUT
31 P76 TA3OUT OUT gui GUI GUI/Select Input Monitor/(SCART) BA2_B L: GUI
P96/TxD4/S-OUT/CST
P95/CLK4/S-CLK/CSC
P94/DA1/DA-OUT/FAN
P93/DA0/TCTS3/CTS
P92/TxD3/S-OUT/TXYDC
P91/RxD3/S-IN/RXYDC
P90/CLK3/S-CLK/RTS
P146/CMOS/IN/VRB
P145/CMOS/IN/VRA
P144/CMOS/OUT/FRMT
P143/CMOS/OUT/SRMT
P142/CMOS/OUT/PRY
P141/CMOS/OUT/ICD
P140/CMOS/OUT/CSY
BYTE
CNVSS
P87/IN/BT232
P86/IN/BTYDC
/RESET
XOUT
VSS
XIN
VCC
P85/NMI/IN
P84/INT2/INT-IN/INT938
P83/INT1/INT-IN/PSW
P82/INT0/INT-IN/REM1
P81/TA4IN/IN/PDET
P80/TA4OUT/IN/XYDC
P77/TA3IN/IN
P76/TA3OUT/OUT/GUI
P75/TA2IN/IN/INTY
P74/TA2OUT/OUT/CEFD
P73/TA1IN/IN/CSINT
P72/CLK2/S-CLK/YSSCK
P71/RxD2/S-IN/SDD
32 P75 TA2IN IN gui /INTY YGV619(GUI) /INT IN (INT Agreement with Setup Condition of Resistor)
33 P74 TA2OUT OUT disp CEFD FL Driver CE OUT
34 P73 TA1IN IN dsp CSINT CS-DSP INT
35 P72 CLK2 S-CLK dsp YSSCK YSS938 CLK OUT (Necessary Pullup ,SerialI/O-0)
36 P71 RxD2 S-IN dsp SDD YSS938 DATA IN (RxD) (Necessary Pullup ,SerialI/O-0)
37 P70 TxD2 S-OUT dsp SDM YSS938 DATA OUT (TxD) (Necessary Pullup ,SerialI/O-0)
8 8 8 8 8 8 8 38 P67 TxD1 OUT amp HPF Head Phone Amp. Filter L: Main Large
39 Vcc - - Power Supply (Backup) +5V
I/O Port Port P0 Port P1 Port P2 Port P3 Port P4 Port P5 Port P6
40 P66 RxD1 OUT amp VIC Video Select C/(SCART)BA2_A
Internal Peripheral Functions 41 VSS - - GND
Timer A-D Converter (10 bits x 8 channels, System Clock Generator
Expendable up to 10 channels) XIN - XOUT 42 P65 CLK1 IN-OUT amp UCDF UCD Clock Frequency Select (3 State) IN: Automatic
Port P7
Timer TA0 (16 bits)

Timer TA1 (16 bits) XCIN - XCOUT
UART/ Clock Synchronous 43 P64 /CTS1 OUT amp /VR1 VCR Rec Out Mute/(SCART)BLANK L: Mute ON
8
Timer TA2 (16 bits) SI/O (8 bits x 5 channels)

Timer TA3 (16 bits)
Timer TA4 (16 bits) X-Y Converter Memory 44 P63 TxD0 S-OUT disp DTFD FL Driver TxD
Port P8
Timer TB0 (16 bits) (16 bits x 16 bits)

Timer TB1 (16 bits) RAM 45 P62 RxD0 IN uop /HP HEAD PHONE Detect (Necessary Pullup) [H: Used]
7
Timer TB2 (16 bits) CRC arithmetic Circuit (CCITT) 24K

Timer TB3 (16 bits) (Polynomial: X16+X12+X5+1)
Timer TB4 (16 bits) 46 P61 CLK0 S-CLK disp CKFD FL Driver CLOCK OUT (SerialI/O-2)
Port P85
Timer TB5 (16 bits)

M16C/80 Series 16-bit CPU core
47 P60 /CTS0 OUT disp /BLK FL Driver Light off L: Reset
Watchdog Timer Registers DRAM
FLG
(15 bits) R0H
R0H R0LR0L
Controller
48 P137 CMOS OUT amp DTBD BD38xx Data Line for Control (Soft Serial)
Port P9
INTB
R1H
R1H R1LR1L ISP
D-A Converter R2 DRAM 49 P136 CMOS OUT amp CKBD BD38xx Serial Clock (Soft Serial, Necessary Pullup)
8
(8 bits x 2 channels) R2 USP

R3 Controller
R3 PC 50 P135 CMOS OUT amp STBY SCART Terminal Stanby cold/hot H: Active
Port P10
SVP
A0
VCT Multiplier
A1 SVF
51 P134 CMOS OUT amp HPMT Head Phone Mute L: Mute
8
SVP
FB SVP
VCT
SB VCT 52 P57 /RDY IN gui YGV619(GUI)/WAIT (Pullup Necessary Resistor)
53 P56 ALE - bus (Unconnected)
Port P15 Port P14 Port P13 Port P12 Port P11 54 P55 /HOLD - bus Connect to Vcc(+5) Through Resistor (100 k-ohms)
8 7 8 8 5 55 P54 HLDA - bus (Unconnected)
56 P133 CMOS OUT dsp /CSCS CS493x CS OUT
40
IC307: M30805SGP (DIGITAL P.C.B) IC307: M30805SGP (DIGITAL P.C.B)

16bit -COM (Main CPU) 16bit -COM (Main CPU)
Pin Pin Name Type I/O Function Name Detail Of Function Pin Pin Name Type I/O Function Name Detail Of Function
57 VSS - - GND 113 P04 D4 - bus Bus (DATA)
58 P132 CMOS OUT dsp /ICCS CS493x RESET OUT 114 P114 CMOS OUT amp MSROOT Main Signal Root L: DSP / H: Analog
59 Vcc - - Power Supply (Backup) +5V 115 P113 CMOS OUT dsp /ICCDK CODEC Reset
60 P131 CMOS OUT dsp /CSPLD DIG EXTERNAL IC CE OUT (When Use PLD) 116 P112 CMOS IN tuner RDSE RDS Enable, RDS Yes or No
61 P130 CMOS OUT gui YGV619(GUI)/RESET OUT [L: RESET] 117 P111 CMOS OUT tuner SCKR RDS Clock
62 P53 BCLK - bus (Unconnected) 118 P110 CMOS OUT tuner SDTR RDS TxD
63 P52 /RD OUT bus Read in Bus CE 119 P03 D3 - bus Bus (DATA)
64 P51 /WRH OUT bus Write in Bus (Uneven) CE 120 P02 D2 - bus Bus (DATA)
65 P50 /WRL OUT bus Write in Bus (Even) CE (Necessary Pullup/Prevent FlashWrite Error) 121 P01 D1 - bus Bus (DATA)
66 P127 - IN tuner /ST STEREO/MONO IN (Necessary Pullup) [L: STEREO] 122 P00 D0 - bus Bus (DATA)
67 P126 CMOS OUT tuner TMT TUNER MUTE OUT H: Mute ON 123 P157 CMOS OUT amp VIB Video Select B/(SCART)BA1_B
68 P125 - IN tuner TUNED STATION IN (Necessary Pullup) [L: Tuned] 124 P156 CMOS OUT amp VIA Video Select A/(SCART)BA1_A
69 P47 /A23 - bus Bus (ADDRESS), Composite CS 125 P155 CMOS OUT amp NTSC NTSC/PAL Select H: NTSC
70 P46 A22 - bus Bus (ADDRESS), Composite CS 126 P154 CMOS OUT amp /CMT Mute Center L: Mute
71 P45 A21 - bus Bus (ADDRESS) 127 P153 CMOS OUT amp /SWMIX SWFR Mix H: Mix
72 P44 A20 - bus Bus (ADDRESS) 128 P152 CMOS OUT amp /CMIX Center Mix H: Mix
73 P43 A19 - bus Bus (ADDRESS) 129 P151 CMOS OUT amp GAIN Gain Control H: A2 Gain
74 Vcc - - Power Supply (Backup) +5V 130 Vss - - GND
75 P42 A18 - bus Bus (ADDRESS) 131 P150 CMOS IN amp PRI UCD Overload Detect
76 Vss - - GND 132 Vcc - - Power Supply (Back up) +5V
77 P41 A17 - bus Bus (ADDRESS) 133 P107 AN7 OUT amp /MTSW MUTE LFE [L: MUTE]
78 P40 A16 - bus Bus (ADDRESS) 134 P106 AN6 A-D IN amp UCDTHM UCD Temperature Detect
79 P37 A15 - bus Bus (ADDRESS) 135 P105 AN5 A-D IN amp PRD DC Detect
80 P36 A14 - bus Bus (ADDRESS) 136 P104 AN4 A-D IN amp THM Temperature Detect [0~VREF]
81 P35 A13 - bus Bus (ADDRESS) 137 P103 AN3 IN amp ACPRT Detect Short-circuit of Trans Harf-wave (Necessary Pullup)
82 P34 A12 - bus Bus (ADDRESS) 138 P102 AN2 A-D IN uop ADKEY0 Operation Button Detect [0~VREF]
83 P33 A11 - bus Bus (ADDRESS) 139 P101 (AN1) OUT bus /BINH Bus Line Voltage Select IC 4245 /OE L: Active
84 P32 A10 - bus Bus (ADDRESS) 140 AVss - - GND
85 P31 A9 - bus Bus (ADDRESS) 141 P100 AN0 A-D IN (Unconnected) [0~VREF]
86 P124 CMOS OUT tuner CEP PLL IC Chip Enable OUT/Distination Discriminate 1 [L: Address H: Data] 142 VREF - - A-D,D-A Power Supply (+5V) (Connect Non Backup Power)
87 P123 CMOS OUT tuner SDTP PLL IC TxD 143 AVcc - - Connect to VCC (+5V) (Connect Backup Power)
88 P122 CMOS IN tuner SDRP PLL IC RxD (Necessary Pullup) 144 P97 RxD4 S-IN dsp CSR CS493x RxD (Necessary pullup)
89 P121 CMOS OUT tuner SCKP PLL IC CLOCK/Distination Discriminate 0 (Necessary Pullup)
90 P120 - IN tuner SDRR RDS IC RxD (Necessary Pullup)
91 Vcc - - Power Supply (Backup) +5V
92 P30 A8 bus Bus (ADDRESS)
93 Vss - - GND
94 P27 A7 - bus Bus (ADDRESS)
102 P17 D15 (/INT5) bus Bus (DATA)
105 P14 D12 - bus Bus (DATA)
41
IC317: YGV619 (DIGITAL P.C.B) IC317: YGV619 (DIGITAL P.C.B)

Video Display Video Display
1 AVSS1 I Ground for Analog Logic of PLLDCK (GND) 61 D20 I/O CPU Data Bus (Unconnected)
2 AVDD1 I Power Supply for Analog Logic of PLLDCK (+3.3 V) 62 D19 I/O CPU Data Bus (Unconnected)
3 A23 I CPU Address Bus bit 23 (for CSMEM) 63 D18 I/O CPU Data Bus (Unconnected)
6 A20 I CPU Address Bus bit 20 (for CSMEM) 66 VSS I Ground for Digital Logic & I/O (GND)
7 A19 I CPU Address Bus bit 19 (for CSMEM) 67 D15 I/O CPU Data Bus
8 VSS I Ground for Digital Logic & I/O (GND) 68 D14 I/O CPU Data Bus
10 VDD I Power Supply for Digital Logic & I/O (+3.3 V) 70 D12 I/O CPU Data Bus
12 A16 I CPU Address Bus bit 16 (for CSMEM) 72 VDD I Power Supply for Digital Logic & I/O (+3.3 V)
16 A12 I CPU Address Bus bit 12 (for CSMEM) 76 VSS I Ground for Digital Logic & I/O (GND)
20 VSS I Ground for Digital Logic & I/O (GND) 80 D4 I/O CPU Data Bus
22 A7 I CPU Address Bus bit 7 (for CSMEM and CSREG) 82 D2 I/O CPU Data Bus
25 VDD I Power Supply for Digital Logic & I/O (+3.3 V) 85 VSS I Ground for Digital Logic & I/O (GND)
26 A4 I CPU Address Bus bit 4 (for CSMEM and CSREG) 86 SYCKOUT O XTAL Output for System Clock (Unconnected)
27 A3 I CPU Address Bus bit 3 (for CSMEM and CSREG) 87 SYCKIN I XTAL Input or Clock generator Input for System Clock
28 A2 I CPU Address Bus bit 2 (for CSMEM and CSREG) 88 VDD I Power Supply for Digital Logic & I/O (+3.3 V)
29 A1/WR3 I Write Strobe for D31-24 (LWD=1) / Address bit 1 (LWD=0) 89 /TEST2 I Test Use Only (Connect to Pull Up Resistance)
30 /WR2 I Write Strobe for D23-16 (LWD=1) / not use (LWD=0) (Unconnected) 90 /TEST1 I Test Use Only (Connect to Pull Up Resistance)
31 /WR1 I Write Strobe for D15-8 91 /TEST0 I Test Use Only (Connect to Pull Up Resistance)
32 VSS I Ground for Digital Logic & I/O (GND) 92 SDQ0 I/O SDRAM Data
33 /WR0 I Write Strobe for D7-0 93 SDQ15 I/O SDRAM Data
34 /RD I Read Strobe 94 SDQ1 I/O SDRAM Data
35 /RESET I Power On Reset 95 VSS I Ground for Digital Logic & I/O (GND)
36 VDD I Power Supply for Digital Logic & I/O (+3.3 V) 96 SDQ14 I/O SDRAM Data
37 /CSREG I Chip Select for Register Port Access 97 SDQ2 I/O SDRAM Data
38 /CSMEM I Chip Select for Memory Port Access 98 SDQ13 I/O SDRAM Data
39 LWD I Select CPU Data Bus Width (32 bits/16 bits) 99 SDQ3 I/O SDRAM Data
40 /LEND I Endian Select 100 VDD I Power Supply for Digital Logic & I/O (+3.3 V)
41 /SYCKS I System Clock Select (Unconnected) 101 SDQ12 I/O SDRAM Data
42 /DREQ O Direct Memory Access Request 102 VSS I Ground for Digital Logic & I/O (GND)
43 VSS I Ground for Digital Logic & I/O (GND) 103 SDQ4 I/O SDRAM Data
44 /READY O Data Access Ready (Unconnected) 104 SDQ11 I/O SDRAM Data
45 /WAIT O Data Access Wait 105 SDQ5 I/O SDRAM Data
46 /INT O Interrupt 106 SDQ10 I/O SDRAM Data
47 D31 I/O CPU Data Bus (Unconnected) 107 SDQ6 I/O SDRAM Data
52 D27 I/O CPU Data Bus (Unconnected) 112 DQM0 O SDRAM Data Mask
53 D26 I/O CPU Data Bus (Unconnected) 113 VDD I Power Supply for Digital Logic & I/O (+3.3 V)
54 D25 I/O CPU Data Bus (Unconnected) 114 /WE O SDRAM Write Enable
55 D24 I/O CPU Data Bus (Unconnected) 115 VSS I Ground for Digital Logic & I/O (GND)
56 VSS I Ground for Digital Logic & I/O (GND) 116 DQM1 O SDRAM Data Mask
57 D23 I/O CPU Data Bus (Unconnected) 117 /CAS O SDRAM Column Address Strobe
58 D22 I/O CPU Data Bus (Unconnected) 118 SDCLK I/O SDRAM Clock
59 D21 I/O CPU Data Bus (Unconnected) 119 AVSS2 I Ground for Analog Logic of PLLVCK (GND)
60 VDD I Power Supply for Digital Logic & I/O (+3.3 V) 120 AVDD2 I Power Supply for Analog Logic of PLLVCK (+3.3 V)
42
IC317: YGV619 (DIGITAL P.C.B) IC317: YGV619 (DIGITAL P.C.B)

Video Display Video Display
121 /RAS O SDRAM Row Address Strobe 181 DRO0 O Digital R Output (Unconnected)
122 /SCS O Chip Select for SDRAM Access 182 DGO5 O Digital G Output (Unconnected)
123 SBA1 O SDRAM Bank Address 183 DGO4 O Digital G Output (Unconnected)
124 SA11 O SDRAM Address (Unconnected) 184 VSS I Ground for Digital Logic & I/O (GND)
125 VSS I Ground for Digital Logic & I/O (GND) 185 DGO3 O Digital G Output (Unconnected)
126 SBA0 O SDRAM Bank Address 186 DGO2 O Digital G Output (Unconnected)
127 VDD I Power Supply for Digital Logic & I/O (+3.3 V) 187 DGO1 O Digital G Output (Unconnected)
128 SA12 O SDRAM Address (Unconnected) 188 DGO0 O Digital G Output (Unconnected)
129 SA9 O SDRAM Address 189 DBO5 O Digital B Output (Unconnected)
130 SA10 O SDRAM Address 190 VSS I Ground for Digital Logic & I/O (GND)
133 SA1 O SDRAM Address 193 VDD I Power Supply for Digital Logic & I/O (+3.3 V)
135 VSS I Ground for Digital Logic & I/O (GND) 195 DBO1 O Digital B Output (Unconnected)
137 SA2 O SDRAM Address 197 VSS I Ground for Digital Logic & I/O (GND)
138 SA5 O SDRAM Address 198 AVSS4 I Ground for Analog Logic of DAC (GND)
139 VDD I Power Supply for Digital Logic & I/O (+3.3 V) 199 B O Linear B
140 SA3 O SDRAM Address 200 AVSS4 I Ground for Analog Logic of DAC (GND)
141 SA4 O SDRAM Address 201 G O Linear G
142 DQM2 O SDRAM Data Mask 202 AVSS4 I Ground for Analog Logic of DAC (GND)
143 DQM3 O SDRAM Data Mask 203 R O Linear R
144 VSS I Ground for Digital Logic & I/O (GND) 204 AVSS4 I Ground for Analog Logic of DAC (GND)
145 SDQ16 I/O SDRAM Data 205 REXT I External Resistance for DAC Amplitude Control
146 SDQ31 I/O SDRAM Data 206 AVDD4 I Power Supply for Analog Logic of DAC (+3.3 V)
147 SDQ17 I/O SDRAM Data 207 AVDD3 I Power Supply for Digital Logic of DAC (+3.3V)
148 SDQ30 I/O SDRAM Data 208 AVSS3 I Ground for Digital Logic of DAC (GND)
149 SDQ18 I/O SDRAM Data 209 DRI5 I Digital R Input (Unconnected)
150 VSS I Ground for Digital Logic & I/O (GND) 210 DRI4 I Digital R Input (Unconnected)
152 VDD I Power Supply for Digital Logic & I/O (+3.3 V) 212 DRI2 I Digital R Input (Unconnected)
153 SDQ19 I/O SDRAM Data 213 VSS I Ground for Digital Logic & I/O (GND)
155 SDQ20 I/O SDRAM Data 215 VDD I Power Supply for Digital Logic & I/O (+3.3 V)
157 VSS I Ground for Digital Logic & I/O (GND) 217 DGI5 I Digital G Input (Unconnected)
158 SDQ21 I/O SDRAM Data 218 DGI4 I Digital G Input (Unconnected)
163 VSS I Ground for Digital Logic & I/O (GND) 223 DBI5 I Digital B Input (Unconnected)
164 SDQ24 I/O SDRAM Data 224 DBI4 I Digital B Input (Unconnected)
166 /CSYNC O Composite Sync. (or Vertical Sync.) 226 DBI3 I Digital B Input (Unconnected)
167 /HSYNC O Horizontal Sync. 227 DBI2 I Digital B Input (Unconnected)
168 /BLANK O Display Enable Timing 228 DBI1 I Digital B Input (Unconnected)
169 FSC O Sub Carrier Clock 229 VDD I Power Supply for Digital Logic & I/O (+3.3 V)
170 AT1 O Attribute bit Out 230 DBI0 I Digital B Input (Unconnected)
171 VSS I Ground for Digital Logic & I/O (GND) 231 GCKIN I External Clock Input
172 AT0 O Attribute bit Out 232 /GCKS I GCK Select (Unconnected)
173 GCKOUT O Clock for Digital Output (Unconnected) 233 /HSIN I Connect External Horizontal Sync. (Unconnected)
174 DRO5 O Digital R Output (Unconnected) 234 /VSIN I Reset Vertical Timing (Unconnected)
175 DRO4 O Digital R Output (Unconnected) 235 /TCKS I Test Use Only (Open)
176 DRO3 O Digital R Output (Unconnected) 236 TCK80 I Test Use Only (Connect to Pull Up Resistance)
177 VSS I Ground for Digital Logic & I/O (GND) 237 VSS I Ground for Digital Logic & I/O (GND)
178 DRO2 O Digital R Output (Unconnected) 238 DCKOUT O XTAL Output for Dot Clock
179 DRO1 O Digital R Output (Unconnected) 239 DCKIN I XTAL Input or Clock generator Input for Dot Clock
180 VDD I Power Supply for Digital Logic & I/O (+3.3 V) 240 VDD I Power Supply for Digital Logic & I/O (+3.3 V)
43
A B C D E F G H I J
1
BLOCK DIAGRAM (U, C, A, L, R, T, K, J models) FL/FR (DSP THROUGH) SELECTOR
IC402
HP
See page 64
SCHEMATIC DIAGRAM
MUTE
IC419 TC74H4053AF [Front] POWER (5)
See page 65 3,13 90Hz See page 62 See page 63
AUDIO SELECTOR
SCHEMATIC DIAGRAM HPF SCHEMATIC DIAGRAM Class-D AMP SCHEMATIC DIAGRAM
IC401 B D3842FS SP TARMINAL
POWER (7) IC332 MAIN UNIT x 6 POWER (3)
1,2 F-SW 1 OUT 31,32 4,14 50,51 IC406, 407 IC411
13,14 21,22 FL/FR 5,12 29,31 IC693
DVD/CD F-SW 2 MUTE
FL / FR
A/D
IC339 E-Volume IC409 IC691
3,4 CODEC 23,24 SL/SR 53,54 23,25
DTV/CBL REC A I C403 MUTE SL / SR
17,18 I C306
IC330 IC692
2 5,6 26 SB 52 BD3815KS 27
VIDEO1 D/A MUTE SB
AK4628VQ
IC330 IC692
7,8 27 C 55 21
TUNER MUTE C
IC406, 407
IC409
VIDEO2 9,10 IC331 E-Volume
28 SW 1,3
[Front]
I C405
See page 64 27 See page 65
POWER (5) 11,12 See page 60 SCHEMATIC DIAGRAM BD3812F MUTE SW out SCHEMATIC DIAGRAM
SCHEMATIC DIAGRAM
INPUT (1) IC408 POWER (9)
VCR in I C302
MSM514260E-60JS I C301 D4 See page 63 SCHEMATIC DIAGRAM
3 MEMORY S5V Q7
4MB DRAM (J Dest. Only) D3 POWER (1)
VCR out S5BK D12 T1
D20 Sub Transformer
See page 65 S3.3V Q2
See page 61 IC551 157
SCHEMATIC DIAGRAM AAC DECORDER D19
SCHEMATIC DIAGRAM DVD/CD I C303 S3.3BK
POWER (8) DIR / AC-3, DP II,
INPUT (2) XC9572XL
IC551
156
dts DECORDER / Sub DSP LSI
(J Dest. Only)
D13
RST
DTV/CBL RESET Circuit
IC304
IC552
154
FAN
VIDEO1 YSS938-F dts-ES / neo:6 / DP IIx
DECORDER
See page 64 SCHEMATIC DIAGRAM See page 64 127 FAN Control
4 SCHEMATIC DIAGRAM VIDEO2
I C305
D14
POWER (4) CS493264
Circuit
[Front]
POWER (5) POW_RY
FAN RY1
FL DRIVER
+B
FL DISPLAY 3
IC101
V101 M66003-0101FP
+12V IC412
26 Level Shift
-COM +A5 Q403 D416
8,9 5V 3.3V GUI LSI Main Transformer
IC307 IC310-IC314
138 , IC340 +A10 Q402
M30805SGP I C317
27 74LVX4245
INPUT / DSP
+7V Q408
STAND- Rotary YGV619-S
5 BY Button Encorder / Tuner Buttom
SW191 SW101 SW102~104 - 7V Q409
REMOTE F-ROM -12V IC413
See page 64 See page 59 SCHEMATIC DIAGRAM
SENSOR I C316
SCHEMATIC DIAGRAM U101
POWER (6) DIGITAL MBM29LV320BE90T V+5 IC414
RGB ENC.
FL1
See page 65 SCHEMATIC DIAGRAM VIDEO SELECTOR SELECTOR GUI 20 SDRAM V-5 IC415
IC261 I C315 FL2
POWER (10) IC282 I C318
TC74HC4051AFEL NJM2233BM MB3516A
W986432DH-7 +5D IC416
14 3 1 +6dB VIDEO AMP
DVD/CD IC281 +3.3D IC418 D417
LA7108M-TLM
6 15 3 7 4 13 +2.5D IC417
DTV/CBL MONITOR out
+5CDC
12 7 11
VIDEO1 VCR out +5GU +B
+3.3GU IC410 D15
See page 64 1
VIDEO2
SCHEMATIC DIAGRAM See page 65
POWER (5) [Front] MUTE
SCHEMATIC DIAGRAM
5 POWER (11)
VCR in
-B
7 See page 60 SCHEMATIC DIAGRAM -27V Q13
INPUT (1)
44
A B C D E F G H I J
1
BLOCK DIAGRAM (B, G models) FL/FR (DSP THROUGH) SELECTOR
IC402
HP
See page 64
SCHEMATIC DIAGRAM
MUTE
IC419 TC74H4053AF [Front] POWER (5)
3,13 90Hz See page 62 See page 63
AUDIO SELECTOR SCHEMATIC DIAGRAM Class-D AMP SCHEMATIC DIAGRAM
IC301 B D3842FS HPF
SP TARMINAL
IC332 MAIN UNIT x 6 POWER (3)
5,6 F-SW 1 OUT 31,32 4,14 50,51 IC406, 407 IC411
13,14 21,22 FL/FR 5,12 29,31 IC693
TUNER F-SW 2 MUTE
FL / FR
A/D
IC339 E-Volume IC409 IC691
VIDEO2 3,4 CODEC 23,24 SL/SR 53,54 23,25
REC A I C403 MUTE SL / SR
[Front] 17,18 I C306
IC330 IC692
2 See page 64 26 SB 52 BD3815KS 27
POWER (5) SCHEMATIC DIAGRAM D/A MUTE SB
AK4628VQ
IC330 IC692
1,2 27 C 55 21
MUTE C
2,6 IC406, 407
IC409
IC331 E-Volume
EXT I/O 1,3 28 SW 1,3
I C405
27 See page 65
11,12 See page 60 SCHEMATIC DIAGRAM BD3812F MUTE SW out SCHEMATIC DIAGRAM
INPUT (1) IC408 POWER (9)
I C302
MSM514260E-60JS D4 See page 63 SCHEMATIC DIAGRAM
3 S5V Q7
4MB DRAM D3 POWER (1)
S5BK D12 T1
2,6 D20 Sub Transformer
IC551
S3.3V Q2
See page 61 157 D19
TV I/O 1,3 SCHEMATIC DIAGRAM DVD/CD S3.3BK
INPUT (2) IC551
DIR / AC-3, DP II,
D13
156 dts DECORDER / Sub DSP LSI RST
DTV/CBL RESET Circuit
See page 65 SCHEMATIC DIAGRAM

IC552
154
IC304 FAN
VIDEO1 +10.6V Q402
POWER (12) YSS938-F dts-ES / neo:6 / DP IIx
DECORDER
See page 64 SCHEMATIC DIAGRAM See page 64 127 FAN Control +5V Q408
4 SCHEMATIC DIAGRAM VIDEO2 I C305 Circuit D14
POWER (4) CS493264
[Front]
POWER (5) POW_RY
FAN RY1
FL DRIVER
+B
FL DISPLAY 3
IC101
V101 M66003-0101FP
+12V IC412
26 -COM Level Shift
+A5 Q403 D416
8,9 5V 3.3V GUI LSI Main Transformer
IC307
IC310-IC314
138 M30805SGP , IC340 +A10 Q402
I C317
27 74LVX4245
INPUT / DSP
+7V Q408
STAND- Rotary YGV619-S
5 BY Button Encorder / Tuner Buttom
SW191 SW101 SW102~104 - 7V Q409
REMOTE F-ROM -12V IC413
See page 64 SENSOR
SCHEMATIC DIAGRAM See page 59 SCHEMATIC DIAGRAM I C316
U101 MBM29LV320BE90T
POWER (6) DIGITAL V+5 IC414
RGB ENC.
FL1
See page 65 SCHEMATIC DIAGRAM VIDEO AMP / SELECTOR GUI 20 SDRAM V-5 IC415
I C315 FL2
POWER (12) IC303 BA7613N MB3516A
I C318
W986432DH-7 +5D IC416
6 8
+3.3D IC418 D417
6 1 +2.5D IC417
EXT I/O TV I/O +5CDC

4
+5GU +B
+3.3GU IC410 D15 SW51
VIDEO AMP / SELECTOR
IC304 BA7613N
8 1
-B SW51
See page 64 4
VIDEO2
7 SCHEMATIC DIAGRAM
POWER (5) [Front] See page 60 SCHEMATIC DIAGRAM -27V Q13
INPUT (1)
45
PIN CONNECTION DIAGRAM
ICs Diodes
1N4002S 1SR154 MA8110-H SB01-05Q
NJM78M12FA NJM78M05DL1A 0NJM79M12DL1A NJM79M05DL1A PC29M33T-E1 PQ05RA1 1SS355 MA8120-M
1SS380 MA8270-M
Anode MA8047-M RB051L-40
MA8056-M RB501V-40
MA8062-H UDZ5.1B
MA8062-M UDZ7.5B
1: IN 1: COM 1: COM 3: IN MA8075-H UDZS5.6BTE-17
3: IN 3: GND 2: IN 2: IN 2: COM MA8100-H
1 Cathode
1: OUT 2: OUT 3: OUT 3: OUT 1: OUT 4
2: COM Anode
PQ3RD13 PQ025EN5MZPH PQ1CG21H2F BA7613N BA15218F TC74HCU04AFEL

NJM2068MD-TE2 TC74VHCT08AFT Cathode
NJM2233BM
PC4570G2
S1NB20 D2SBA20 D5SB20
8 7
8 4 14
1 +
1 1 1
1 5 1
5
~
~
74LCX07MTCX 74VHC153MTC TC74HC4053AF TC74HC4051AFEL 74LVX4245MTCX CY62256LL-70SNCT ~ ~ +
BD3812F-E2 LA7108M BD3842FS-E2 +
LC72722PM
MB3516APF-G-BND
7 8 8 14
14 8 16 28
12
16 24
1 1 1
1 1 1
MSM514260E-60JS CS493264-CL
CS493292-CLR
AK4628VQ MBM29LV320BE90T BD3815KS Transistors
42 29
28 18 33 23 1 48
43 28
2SA1015 2SA1674 2SD2396
29 17 34 22 2SC1815 2SC3330
20
39 7 44 12
40 56 15
24 25
1 6 1 11
1 40 44 1 14
E
M66003-0101FP W986432DH-7 XC9572XL-10TQ100C M30802SGP E
CB CB
M30805SGP BC
E
108 73
109 72 2SC4488 2SA1037K 2SD1760

48 33
75 51 2SC3326
2SC2412K
49 32 43 76 50 2SD1938F
DTA114EKA
DTC114EKA C
DTC144EKA
E
64 17 B B C
C B
86 E E
1 16
100 26
1
1 25 144 37
1 36
YSS938 YGV619
180 121
120 81 181 120
121 80
160 41 240 61
1 40 1 60
46
A B C D E F G H I J
1
PRINTED CIRCUIT BOARD (Foil side)
DIGITAL P. C. B. (Lead Type Device) DIGITAL P. C. B. (Surface Mount Device)

B, G models only
INPUT (1)
INPUT (2) POWER (12)
POWER (1)
GAIN_CNTL
VCR_MUTE
HP_MUTE
ST/MONO
RDS_TXD
PLL_TXD
PLL_CLK
CMPSTB
STATION
RDS_CE
SW_MIX
VIDEO1_CXD
OL_CLK
GUI_V
STBY_CTRL
AGND
AGND
FROM_RST
RIN
SW
SR
DTV_D
SB
FL
DGND
AC_PRT
2
PW_DN
S3.3BK
/RES
+10.6V
RXD
CTS
TXD
SGND
VOL_CLK
S5V
VOL_DA
-27V
DSP_THROUGH
S5V
+10.6V
GGND
VIDEO1_CX
NC
NC
NC
LFE_MUTE
FAN_CTRL
YDCBOOT
RDS_RXD
TU_MUTE
RDS_CLK
232BOOT
PLL_RXD
POW_RY
CMPSTC
CMPSTA
DC_PRT
GUI_SW
VOL_DA
PLL_CE
CT_MIX
RESET
DVD_D
BA2_B
BA2_A
BA1_B
BA1_A
SGND
SGND
AGND
AGND
VGND
FUNC
S3.3V
S5BK
THM
HPF
RTS
+5D
+5V
+5V
GUI
LIN
NC
FR
SL
C
3
1 8 1 8 5
8
109 144
108 1 28 15
5
4 5 4
1
1
8
5 1 14
4
73 36 13 24 7 1
23 33 72 37
22 34 1 7
26 50 12 1
25 51
4 14 8 12 1 8 1 12 1
12 44 14 8 8 14
11 1
8 14
1 75 9 16 13 24
41 80 100 76
40 81 61 120 1 7
60 121 13 24 1 86
1 40 1 7
1 24
48 25
28 18 1 24
29 17 12 13
1 24
5 12 12 13
13 43 44
1 24
1 120 20 21 39 7
160 121 40 6 1 24
1 180 12 13
240 181
7 8
1
14
FL_CLK FL_TXD
FL_CE
ROT_B SGND
ROT_A
KEY
SGND
REMOTE
SGND
HP_DET
6 AC_PRT ERR ENABLE

-12V -27V
AGND MUTE_C MUTE_FS
+12V D_GND UCD_TH CLOCK
+2.5D
FL_RST
SGND
S5V
+5D +3.3D
VIDEO2_D
+5D
S5V
STBY/ON
+5CDC
+5GU
+3.3GU
S5V
DC_PRT SGND
MAIN (4) Semiconductor Location
POWER (4) POWER (5) Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location
INPUT (1) D303 G4 D309 I3 IC305 H5 IC313 H5 IC329 B6 IC335 J4
D304 G4 D310 I5 IC306 A4 IC314 H5 IC330 G3 IC336 H4
D305 G4 IC301 H3 IC307 D3 IC315 E4 IC331 G3 IC337 G4
D306 G4 IC302 G5 IC310 I4 IC316 I5 IC332 F4 IC339 G3
7
D307 I3 IC303 C4 IC311 I4 IC317 D5 IC333 I4 IC340 I5
D308 I3 IC304 B5 IC312 H5 IC318 J5 IC334 D4
47
A B C D E F G H I J
1
INPUT (1) P. C. B. (Lead Type Device) INPUT (2) P. C. B. (Lead Type Device)
U, C, A, L, R, T, K, J POWER (11)
models only DIGITAL INPUT
OPTICAL COAXIAL
VCR_MUTE
WRITER 1 2 3
VCRO_V
GUI_SW
VCRI_V
2
GUI_V
DVD DTV
VGND
VGND
VIDEO 1
V+5
V-5
NC
NC
NC
/ CD / CBL
/RES
RXD
CTS
TXD
S5V
YDCBOOT
232BOOT
RTS
MG
POWER (8) POWER (5) MAIN (4)
SW_MUTE
VCRO_R
VIDEO2_R
VIDEO2_V
VCRO_L
VIDEO2_L
3
SWOUT
VCRI_R
VCRI_L
MUTE_C
AGND
AGND
CH6IN
CH5IN
CH4IN
CH3IN
CH2IN
CH1IN
AGND
VGND
HP_G
HP_R
+12V
HP_L
NC
+5D
MUTE_FS
DGND
AGND
AGND
AGND
AGND
AGND
-12V
B, G models only
SWOUT
SW_MUTE
AGND
NC
TRANSFORMER
RTS
SGND
YDCBOOT
232BOOT
DVD_D
+5D
VIDEO1_CX
POWER (9) AC2L
S5V
/RES
CTS
TXD
RXD
DGND
DTV_D
VIDEO1_CXD
AC2G
U, C, A, L, R, T, K, J AC2N
4 AC3N
models only
AC3L
VCRO_V
VGND
VCRI_V
VGND
VIDEO2_V
V-5
CMPSTC
CMPSTB
CMPSTA
V+5
F1
F2 DIGITAL
DC_PRT
POWER (10) S5V
SGND
+3.3GU
+5GU
+5CDC
+5D
TUNER_R +3.3D
E +2.5D
TUNER_L DGND
+12V
E AGND
VIDEO2_R -12V
E -27V
VIDEO2_L AC_PRT
E
ADR
E
ADL
E
5 VGND
VIDEO2_V
DIGITAL
CHASSIS
VIDEO1_L
VIDEO1_R
AGNC
DTV_L
DTV_R
AGNC
DVD_L
DVD_R
POWER (12) U, C, A, L, R, T, K, J
models only
B, G models only POWER (7)

BL
GUI_SW
VCR_MUTE
RDS
TUNER_STATION
TUNER_MUTE
TGND
PLL_RXD
PLL_TXD
DSP_THRU
HP_MUTE
LFE_MUTE
GUI_V 5
6 VGND
GAIN
CTMIX
SWMIX
VOL_DA
VOL_CL
CMPSTA
CMPSTB
CMPSTC
RDS_TXD POWER (4)
RDS_CLK
RDS_CE 1 Semiconductor Location
NC
10V
TUNER_L
TUNER_R
PLL_CLK
PLL_CE
TUNER_STEREO/MONO
RDS_RXD
PLL_CLK
PLL_RXD
PLL_CE
PLL_TXD Ref. No. Location
STATION
TU_MUTE
HPF
ST/MONO
F1
D416 H4
RIN F2
LIN
DAR
E DGND
-27V
D417 H5
DAL +5V
E IC410 G6
SR
SL
E
C IC412 H5
SB
E
SW
IC416 G6
TUNER PACK Q408 F5
7 Q409 F5
DIGITAL
48
A B C D E F G H I J
1
INPUT (1) P. C. B. (Surface Mount Device) INPUT (2) P. C. B. (Surface Mount Device)
14 8
3
7 1
4 1 1 7
8 14
5 8
4 1
4 1
4 5 8
5 8
Semiconductor Location
Ref. No. Location Ref. No. Location
D401 C3 IC408 D4
4 1 D402 C6 IC409 D5
8 1
D403 C7 IC411 E4
12 1 D404 E5 IC413 F5
5 8
9 16 D405 E5 IC414 F5
13 24
D406 F6 IC415 F6
5 D407 F4 IC417 F6
D408 F5 IC418 E7
D409 G6 IC419 D5
8 1 8 1 D410 F6 IC551 I3
D411 B4 IC552 I3
9 16 9 16
D412 E5 Q401 C3
D413 D5 Q402 C6
D414 E6 Q403 C6
D415 E6 Q404 C3
D418 G4 Q405 C3
5 1 D419 E4 Q406 C2
6 43 42 D420 E4 Q407 C2
D551 I3 Q410 B4
56 29
1 28
D552 I3 Q411 F4
24 13 IC401 B5 Q412 F4
14 15 IC402 C3 Q413 F4
14 8
IC403 E6 Q414 F4
1 12 IC404 C7 Q415 E4
IC405 D6 Q416 F4
1 7 IC406 D5 Q417 E4
IC407 E5 Q418 E4
49
A B C D E F G H I J
1
POWER (1)
MAIN (1) P. C. B. (Lead Type Device)
2
MAIN (4)
UCD-B
UCDG
UCD+B
ERR
UCH2OUT ENABLE
AGND_CH1
UCDG_CH2
UCH1IN
UCH1OUT AGND_CH1
UCDG_CH1 UCH2IN
AGND_CH2
CLKOUT
+VB
+VB
-VB
-VB
GND
VDR
ENABLE
ERR
OUTPUT
OUTPUT
OUTPUT
GND
GND
GND
NONINV
INV
CLOCK
+VB
+VB
-VB
-VB
GND
VDR
ENABLE
ERR
OUTPUT
OUTPUT
OUTPUT
GND
GND
GND
NONINV
INV
CLOCK
POWER (3)
UCD UNIT [CH1] SLch UCD UNIT [CH2] SRch

POWER INPUT / OUTPUT
UCD UNIT [CH1] SLch UCD UNIT [CH2] SRch
4 INPUT / OUTPUT POWER
POWER (1)
MAIN (4)
UCD-B Semiconductor Location
5 UCDG Ref. No. Location
UCD+B
ERR D601 D3
NC D602 F3
UCH4OUT ENABLE
AGND_CH3 D603 G2
UCDG_CH4
UCH3IN D604 G3
UCDG_CH4 AGND_CH3
UCH3OUT D605 G3
UCH4IN
UCDG_CH3 AGND_CH4 D631 D5
CLKOUT D632 F5
D633 G5
D634 G5
+VB
+VB
-VB
-VB
GND
VDR
ENABLE
ERR
OUTPUT
OUTPUT
OUTPUT
GND
GND
GND
NONINV
INV
CLOCK
+VB
+VB
-VB
-VB
GND
VDR
ENABLE
ERR
OUTPUT
OUTPUT
OUTPUT
GND
GND
GND
NONINV
INV
CLOCK
D635 G5
6 POWER (3) Q601 E2
Q602 D3
Q603 F3
Q604 E2
Q605 G2
UCD UNIT [CH3] SBch UCD UNIT [CH4] Cch Q631 E5
Q632 D5
Q633 F5
UCD UNIT [CH3] SBch UCD UNIT [CH4] Cch Q634 E5
INPUT / OUTPUT POWER Q635 G5
50
A B C D E F G H I J
1
POWER (1)
MAIN (3) P. C. B. (Lead Type Device) MAIN (4)
2 UCD-B
UCDG
UCD+B UCD_TH
+5D
ERR
UCH6OUT ENABLE
DGND
UCDG_CH6 UCH5IN
UCDG_CH6 AGND_CH5
UCH5OUT UCH6IN
UCDG_CH5 AGND_CH6
CLKOUT
UCDG_CH5
+VB
+VB
-VB
-VB
GND
VDR
ENABLE
ERR
OUTPUT
OUTPUT
OUTPUT
GND
GND
GND
NONINV
INV
CLOCK
+VB
+VB
-VB
-VB
GND
VDR
ENABLE
ERR
OUTPUT
OUTPUT
OUTPUT
GND
GND
GND
NONINV
INV
CLOCK
POWER (3)
UCD UNIT [CH5] FLch UCD UNIT [CH6] FRch
UCD UNIT [CH5] FLch UCD UNIT [CH6] FRch
INPUT / OUTPUT POWER
DIGITAL
4
MUTE_FS
ENABLE
CLK
INPUT (1)
MUTE_C
UCD_TH
ERR
MAIN (1) Ref. No. Location
MUTE_C
MUTE_FS D661 C3
CH1IN
AGND D662 F3
CH2IN
AGND D663 E2
5 AGND
CH3IN
ERR D664 E2
CH4IN
ENABLE 1 4 4 AGND
AGND_CH1 4 CH5IN D665 F2
8 14 1 1 AGND
UCH1IN CH6IN D666 F3
AGND_CH1 -12V
8 5 +12V
UCH2IN DGND D667 F3
7 1 8 5 8 5 +5D
AGND_CH2 IC691 E5
CLKOUT
IC692 F5
IC693 G5
IC694 D5
Q661 D2
Q662 C2
6 Q663 F2
ERR UCD_TH Q664 D2
NC +5D
ENABLE Q665 F2
ERR
AGND_CH3 ENABLE Q666 E2
UCH3IN DGND Q667 E2
AGND_CH3 UCH5IN
UCH4IN AGND_CH5 Q668 E2
AGND_CH4 UCH6IN Q691 D5
CLKOUT AGND_CH6
CLKOUT Q692 D5
Q693 D5
Q694 D5
MAIN (2) MAIN (3) Q695 D5
7
51
A B C D E F G H I J
1
POWER (1) P. C. B. (Lead Type Device)
FAN
UCDG
+24V
3 DIGITAL
YE
BL
NC
S3.3BK
FROM_RST THM
S3.3V
S5V
S5BK
SGND
PW_DN RESET
POW_RY
AC_PRT
DC_PRT
MAIN TRANSFORMER
-27V
FAN
STBY_CTRL
+5V
AC1N
AC1G
AC1L
+10.6V
4
MAIN TRANSFORMER
[ U, C, A, L, R, T, K, J models]
POWER (2)
[ B, G models]
UCD-B
UCD-B
UCD-B
UCDG
UCDG
UCDG
UCD+B
UCD+B
UCD+B
MAIN (1) ~ (3)
5 POWER (2) P. C. B. (Lead Type Device) POWER (3) P. C. B. (Lead Type Device)
B, G models only
POWER (1) MAIN (3)
MAIN (2)
MAIN (1)
G
N
Y L
G C1
BR C1
YE C1
UCDG_CH6
UCDG_CH6
UCDG_CH5
UCDG_CH5
UCDG_CH4
UCDG_CH4
UCDG_CH3
UCDG_CH2
UCDG_CH1
A
UCH6OUT
UCH5OUT
UCH4OUT
UCH3OUT
UCH2OUT
UCH1OUT
IMPEDANCE
SELECTOR
6
Ref. No. Location
D4 E2
D12 F2
D15 E4
D20 C3
AC1N_H
AC1N_L
AC1G
AC1L_L
AC1L_H
IC1 D2
Q2 E2
Q7 E2
MAIN TRANSFORMER R L R L Q10 E3
7
[ B, G models] FRONT CENTER SURROUND SURR. Q12 F3
BACK Q13 D3
52
A B C D E F G H I J
1
POWER (1) P. C. B. (Surface Mount Device)
5 POWER (3) P. C. B. (Surface Mount Device)
D1 E2 D17 E4
D2 C2 D18 E4
D3 D2 D19 B3
D5 D2 Q1 C2
D6 C2 Q3 C2
6 D7 C2 Q4 C2
D8 E2 Q5 C2
D9 C2 Q6 C2
D10 C2 Q8 C2
D11 D3 Q9 C2
D13 F3 Q11 D3
D14 F3 Q14 D2
D16 G3 Q15 D3
53
A B C D E F G H I J
1

DIGITAL
INPUT (1)
FL_CLK
ROT_B
FLRST
SGND
S5V
VFL
F2
2
REMOTE
FL_TXD
ROT_A
FL_CE
DGND
SGND
SGND
KEY
S5V
+5D
F1
VOLUME / SELECT INPUT DSP TUNER
4 POWER (5) P. C. B. (Lead Type Device) POWER (6) P. C. B. POWER (7) P. C. B. POWER (8) P. C. B.
(Lead Type Device) (Lead Type Device) (Lead Type Device)
INPUT (1)
INPUT (1)
PHONES VIDEO AUDIO OPTICAL
L R STBY/ON
SW_MUTE
S5V
VCRO_R
VCRO_L
VIDEO1_R
SWOUT
VCRI_R
VIDEO1_L
VCRI_L
AGND
AGND
DVD_R
DTV_R
AUDIO
DVD_L
DTV_L
AGND
AGND
NC
5
VIDEO 1 SUBWOOFER
DTV / CBL VCR OUT

REMOTE
S5V S5V
STBY/ON SGND
STANDBY
/ ON DVD / CD VCR IN
6
HP_L
HP_G
HP_R
VGND
VIDEO_V
AGND
VIDEO2_L
VIDEO2_R
STBY/ON
S5V
+5D
VIDEO2_D
HP_DET
SGND
REMOTE
DGND
INPUT (1)
DIGITAL
7
54
A B C D E F G H I J
1
POWER (4) P. C. B. (Surface Mount Device)
49 48
64 33
1 32
16 17
3
4 POWER (5) P. C. B. (Surface Mount Device) POWER (7) P. C. B. POWER (8) P. C. B.

(Surface Mount Device) (Surface Mount Device)
D101 D3 Q106 E3
IC101 F3 Q108 G3
Q102 D2 Q161 C5
Q103 H3 Q162 C5
7 Q104 D3 Q221 I5
Q105 D3 Q222 I5
55
7
6
5
4
3
2
1
56
A
B
B, G models only
NC
AGND
SW-MUTE
NC SWOUT
NC
NC
V+5
V-5
VCRI_V
VGND
VCRO_V
VGND
C
POWER (11) P. C. B.
GUI_V
INPUT (1)
VCR_MUTE
GUI_SW
INPUT (1)
(Lead Type Device)

D
SUBWOOFER
DIGITAL
VIDEO
VCR IN
V+5
CMPSTA
VCR OUT
MONITOR
CMPSTB
CMPSTC
V-5
VIDEO2_V
VGND
1
[ SCART OUT ]
TV IN / OUT
VCRI_V
1
BA1_A
E
GGND VGND
BA1_B
NC VCRO_V
SGND
NC
GUI_V
BA2_A NC
VOL_CL
BA2_B A(B)OUT
VOL_DA A(B)IN
+5V
+10.6V A(A)OUT
FUNCTION
POWER (10) P. C. B.
A-COM
8
8
RETURN
A(A)IN
BLUE_I/O
INPUT (1)
FUNC_SW
RETURN
CONT
GREEN_I/O
NC
POWER (12) P. C. B.
RETURN
F
RETURN
RED_I/O
BLK_I/O
RETURN
RETURN
V-OUT
V-IN
(Lead Type Device)
VIDEO
GND
VIDEO 1
DVD / CD
DTV / CBL
(Lead Type Device)

G
GND
V-IN
V-OUT
RETURN
RETURN
BLK_I/O
RED_I/O
RETURN
RETURN
NC
GREEN_I/O
CONT
H
TUNER_R RETURN
E
TUNER_L FUNC_SW
E BLUE_I/O
VIDEO2_R
E A(A)IN
VIDEO2_L RETURN
E
ADR A-COM
E A(A)OUT
ADL
E A(B)IN
IC304
IC303
VIDEO2_V A(B)OUT
VGND
E5
E6
Ref. No. Location
I
[ SCART IN ]
EXT IN / OUT
INPUT (1)
J
A B C D E F G H I J
1
POWER (9) P. C. B. (Surface Mount Device) POWER (10) P. C. B. (Surface Mount Device)
Ref. No. Location
2 D301 H5
D302 H5
D303 H6
IC261 E3
IC281 C5
IC282 B5
IC301 H6
8 1
Q241 B3
Q242 B3
9 16 Q301 H5
Q302 H5
3
Q303 H5
Q304 H5
Q305 H5
Q306 H6
Q308 F6
Q309 F6
POWER (11) P. C. B. (Surface Mount Device) POWER (12) P. C. B. (Surface Mount Device)
16 9
4 1
1 8
5
6 8
12 1
6 13 24
57
A B C D E F G H I J K L M N
SCHEMATIC DIAGRAM (DIGITAL)
1
Page 63 D8 Page 64 D5 Page 64 G8 Page 60 E1 Page 65 F3
to POWER (1) to POWER (5) to POWER (4) to INPUT (1) to POWER (12) IC301: CY62256LL-70SNCT
Static RAM
4.9
3.0
0.7
0
RGB ENCODER
A10 INPUT
I/O0
4.9 1.7
A9
ROW DECODER
1.3 BUFFER I/O1
A8
1.2 A7 I/O2
A6
SENCE
1.0
AMPS
A5 512x512 I/O3
1.3
A4 ARRAY I/O4
0
0 A3
A2 I/O5
I/O6
2 CE
WE COLUMN
POWER
DOWN
I/O7
3.3
0
DECODER
3.3
3.3
3.3
3.3
1.7
0.3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
OE
3.3
4.6
4.9
5.1
4.9
4.9
4.9
4.9
4.9
4.9
1.7
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
A14
A13
A12
A11
A1
A0
1.6 5.0
x: NOT USED 5.0
3.6 3.3
O: USED / APPLICABLE
2.7 4.9
Page 61 J3 Page 60 H1 Page 62 L7

1.4
3.3
MICRO COMPUTER 0
4.9
0 3.3
0
1.7
to INPUT (2) to INPUT (1) to MAIN (4) 0

4.9 0 IC302: MSM514260E-60JS
4.9 0
0 4Mbit DRAM
0 4.9 WE OE
0
Point 2 Pin 20 of IC307 4.9
3.3
3.3 13 27
0 1.1
3.7
2.5 4.9
0 VIDEO DISPLAY 0
0
0
RAS 14
Timing
Generator
I/O
4M DRAM 3.3
1.8
4.9
4.9
3.3
0
3.3 0
0 LCAS
UCAS
29
28
Controller
8
Output 8
0 I/O Buffers
4.8 0 0 Controller
0 0 0 DQ1~DQ8
0 0 0 Column
4.8
3 0
0 4.9
0
0
0
0
0
9 Address
Buffers
9 Column Decoders 8
Input
Buffers
8
4.9 0 0 0 0
1.6 1.6 DIGITAL INPUT 3.1 4.9 0 0 Internal Sense Amplifiers 16
I/O
16
1.6 1.6 0 Refresh Selector
4.9 0 3.3 A0~A8 Address
Control Clock
1.6 1.6 Counter
5.0 4.3 4.9 0 0
1.7 1.6 Input
5.0 0 0 0 8 8
4.9 0 Buffers
0.1 0 0 0 Row
2.1 1.6 9 9
Row
2.5 0 4.9 0 Address Word Memory DQ9~DQ16
Deco-
2.3
2.1
1.7
0
~
~
1.7
1.6
1.6
1.7
1.7
1.0
3.3
1.7
2.3 1.6 Buffers
~
~
2.5 Drivers
0
4.9 0 ders Cells
~ 1.6 1.6
4.9 3.3
3.3
Point 1 Pin 239 of IC317 0 8
Output
8
~ 1.6 0 Buffers
0 0 0 0
1.6
4.9 0
1.6
1.6
1.6
1.6
1.6
1.6
1.6
3.3
0
2.1 5.1 VCC 20
3.0
3.0
2.1
1.6 0
2.5 0 3.3
3.0 2.1 0 1.6 0 On Chip
3.3
1.7 3.0
~
2.5
0.4
DSP 0
2.5 0
5.0
2
0
4.9 4.9 2.4

0
3.3
3.3 VSS 21
VBB Generator
1.0 ~ 0 0 5.0 0 5.1

4.7 0
3.3
4.9
5.1
1.7
4.9
4.9
4.6
~ 4.8 0.8
0
0
0
0
3.3
1.6 1.9 3.7
0
4.9
4.9
2.4
4.9
4.9
4.8
4.9
0.2
4.9
1.4
5.1
4.9
4.9
0.3
1.7 1.6 0
0
0
0
0
0
0
0
1.8
4.9 0
2.2
0.4
2.4
0
Point 3 Pin 1 of IC304
4 0
0
2.5
3.7
3.3
3.3 IC303: XC9572XL-10TQ100C
1.4 CPLD
2.7
3.6 3
0 JTAG
0 0 JTAG Port 1 In-System Programming Controller
0 3.3 Controller
0 0 0 1.6
1.2 0 0 0 0 0 0 0 0 0 0
3.3
0 0 0 0 3.6 0 0 4.0 0 1.8 0
2.8
0 1.3 0 2.9 0 2.7 3.6 5.4 0 0 4.9
3.3 3.3 54 Function
1.3 1.8 0 1.4 2.7 0 1.7 4.9 0 0 I/O
3.5 Block 1
3.3 0 2.9 0 3.3 1.4 5.0 4.9 1.7 0 0 4.9 18
0 2.9 Macrocells
3.5 0 3.7 3.3 5.0 5.0 1.6 0 0 0 I/O
1.8 1 to 18
2.8 0 2.5 3.7 5.0 5.0 1.4 4.9 0 0
2.9 I/O
0 1.1 3.3 0 0.4 2.5 0 0 1.4 0 0 0
0 0 3.5
4.0 4.9 1.6 0 1.8 3.3 2.9 0 1.9 0
0 3.3 0 I/O 54
0 0 1.6 0 1.8 0 0 0 0 4.6 Function
Fast CONNECT II Switch Matrix

0.2 4.9
3.3 Block 1
3 1 3.2 5.0 3.2 1.1 3.2 1.1 3.2 5.0 3.2 5.0 3.2 5.0 18
0.3 2
0.1 0.1
0.8 1.6 3.2 5.0 3.2 5.0 3.2 5.0 3.2 5.0 3.2 5.0 3.2 5.0
1.6
0
1 Macrocells
1 to 18
4.9 1.7
1.6
4.9 1.7 I/O
3.3 I/O
4
5 6
0 5
0 0 0
0
I/O
Blocks 54 Function
Block 1
STATIC RAM 0 0
4.0
I/O
18
Macrocells
5.0
5.0
5.0
3.3
2.9
4.0
3.4
1.7
1.7
1.6
1.4
1.9
1.8
3.3
4.9
4.9
1.1
3.3
3.3
3.3
3.3
2.4
4.9 1 to 18
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2.5 I/O
0
2.5
4.9
3.3
3.2
3.2
0 0 3
2.5
3 3.3
3.3
I/O/GCK
I/O/GSR
1
54 Function
Block 1
18
2 Macrocells
1.0
3.3
4.9
I/O/GTS 1 to 18
1.6
1.6
0
3.2
4.9
3.2
1.3
3.3
1.9
0
0
4.9
3.3
0.2
0.2
3.3
0.2
0.2
4.9
0
0
0
0
0
0
0
0
0
0
0
1.7
1.8
0
3.2 3.2
2.5
4.9
0
2.5
0
3.3
3.3
1.7
3.3
3.3
3.3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
3.2
0
3.2
0
0
SDRAM
0
0
4.9
0
4.9
1.6
0
4.9
4.9
2.4
0 2.5 IC305 (U, C, R, T, K, B, G model): CS493264-CL
SURROUND BACK
SCDIO, SCDOUT, PSEL, GPIO9

0 2.5 IC305 (J model): CS493292-CLR
D/A 0
3.3
3.3
3.3
3.3
3.3
3.3
0.3
1.7
3.3
3.3
3.3
3.3
1.7 11.8 Audio Decoder
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CENTER
RD, R/W, EOME, GPIO11

WR, DS, EMWR, GPIO10
6 1.7 0 0
DATA7, EMAD7, GPIO7

DATA6, EMAD6, GPIO6
DATA5, EMAD5, GPIO5
DATA4, EMAD4, GPIO4
DATA3, EMAD3, GPIO3
DATA2, EMAD2, GPIO2
DATA1, EMAD1, GPIO1
DATA0, EMAD0, GPIO0
1.2
0
CONVERTER 2.4
2.5
0
0
EXTMEM, GPIO8
ABOOT, INTREQ
1.3 2.5
1.3
A0, SCCLK
A1, SCDIN
3.3
0 2.4
RESET
0
1.3
4.9
4.9
4.9
4.9
2.4
2.4
2.5
2.5
2.4
2.5
2.5
2.5
2.5
2.5
2.6
0 2.4
0
0
1.3
3.2
2.8
3.3
2.6
2.8
2.8
2.8
2.7
3.3
CS
0
0
0 -11.9
3.3 SURROUND L 3.3 3.3 36 8 9 10 11 14 15 16 17 18 5 4 19 7 6 20 21
2.5
2.5
2.6
0
2.5
0
2.0
0
1.6
3.3 0 3.3
0
3.3
0
2.8
2.9
1.7
1.7
DTS-ES / 1.7
1.7
0
11.8 4.9 CMPDAT, SDATAN2, RCV958 27
Compressed
Parallel or Serial Host Interface
37
38
DD
DC
1.1
2.5
1.7
2.5
0
NEO:6 0
2.5
0.9
FRONT L 0 0
1.8
0
CMPCLK, SCLKN2
CMPREQ, LRCLKN2
28
29
Data Input
Interface Frame
Shifter 24-Bit
44 MCLK
0
2.3 0
0
0.9
DECODER 0.3
2.5 0.4
2.5
0
0
SCLKN1, STCCLK2 25
Input
Buffer
DSP Processing
RAM RAM
Program Data RAM Output
43
42
SCLK
LRCLK
Digital Controller Buffer Output 39 AUDATA2
2.3 2.5 3.7 0 Memory Memory
Audio Formatter AUDATA1
CPLD
0 1.3 LRCLKN1 26 40
3.3 0 ROM ROM
3.3
2.5
2.5
2.4
2.5
2.5
2.5
2.5
2.5
2.5
3.3 3.2 Input

0
0.9 0 Program Data 41 AUDATA0

1.4 0 SDATAN1 22 Interface
0 RAM Input Memory Memory 3 AUDATA3, XMT958
0.3 2.5 0 2.7 0
0.5
4.8 Buffer STC
2.5 2.8 3.6 0 CLKIN 30
2.5 0 PLL
7 3.3
2.6
3.3
2.8
-11.9
11.8
1.6
3.3
0
1.8
CLKSEL 31 Clock Manager
0
0.8 2.8 2.8 1.9
0.4 0 0 3.5 1.4 32 33 34 35 24 13 2 23 12 1
4.9
FILT2
FILT1
VA
AGND
DGND3
DGND2
DGND1
VD3
VD2
VD1
4.7 2.9 1.6
4.9 0.3 1.8 1.7
2.8
4.8 0.3 0.3 2.9 1.7
2.8
4.9 0
0 3.5 3.4
4.8 4.0
0
0 0 2.9
2.6
3.3 0 0 0
2.8 0
4.9 5.0
IC306: AK4628VQ
2.5
0 3.3 0 -11.9 192kHz 24Bit 8-channel CODEC
~
~
~
~
3.3 5.0
11.8 5.0
0
4.8 2.6
3.3
0 0
0
3.3
Audio
0
4.9 3.3
LIN 31 ADC HPF I/F
1.2
4.9
3.3
3.3
0
3.2
2.0
4.9 3.3 0
RIN 32 ADC HPF
4.8 3.3
3.3 3.3
LOUT1 27 LPF DAC DATT MCLK 39 MCLK
0
8 3.3 3.3
0
0 ROUT1 28 LPF DAC DATT

LRCK
BICK
5
4
LRCK
BICK
-11.9
10 DAUX
LOUT2 25 LPF DAC DATT
Format
Converter
ROUT2 26 LPF DAC DATT
SDOUT
LOUT3 23 LPF DAC DATT 1 SDOS
IC318: W986432DH-7 All voltages are measured with a 10M/V DC electronic volt meter. 10M 9 SDTO
IC333~336: 74LCX07MTCX IC329: TC74VHCT08AFT

SDRAM
CLK
Components having special characteristics are marked s and must be replaced s ROUT3 24 LPF DAC DATT SDIN1
SDIN2
6
7
SDTI1
SDTI2
Hex Buffer Quad 2-Input And Gate CLOCK
with parts having specifications equal to those originally installed. SDIN3 8 SDTI3
LOOP0/SDA/CDTI
BUFFER LOUT4 21 LPF DAC DATT SDIN4
DIF1/SCL/CCLK
12 SDTI4
VCC 1 86 GND Schematic diagram is subject to change without notice.
DQ0 2 85 DQ15 CKE
A0 1 14 VCC
DIF0/CSN
1A 1 14 Vcc ROUT4 22 LPF DAC DATT
VccQ 3 84 GND
VREFH
VCOM
MCLK
TDM0
AVDD
AVSS
DZF1
1B 2 13 4B DQ1 4 83 DQ14 AK4628
O0 2 13 A3
P/S
DQ2 5 82 DQ13 CS
1Y 3 12 4A CONTROL
GND 6 81 VccQ SIGNAL
A1 3 12 O3 2A 4 11 4Y MONITOR
44
43
42
41
40
39
38
37
36
35
34
DQ3 7 80 DQ12 RAS
COMMAND SDOS 1 33 DZF2/OVF
DQ4 8 79 DQ11 DECODER
O1 4 11 A4 2B 5 10 3B CAS
VccQ 9 78 GND I2C 2 32 RIN
9 A2 5
2Y 6 9 3A DQ5 10 77 DQ10 WE COLUMN DECODER COLUMN DECODER IC316: MBM29LV320BE90T IC315: MB3516APF-G-BND IC310~314, 340: 74LVX4245MTCX SMUTE 3 31 LIN
10 O4 DQ6 11 76 DQ9 BICK 4 30 NC
GND 7 8 3Y 4Mbit Flash Memory RGB Encoder 8-Bit Dual Supply Translating Transceiver
ROW DECODER
ROW DECODER
GND 12 75 VccQ LRCK 5 29 MASTER

RY/BY DQ15 to DQ0
O2 6 9 A5 DQ7 13 74 DQ8 SDTI1 6 28 ROUT1
CELL ARRAY CELL ARRAY GND2 R-OUT G-OUT B-OUT VIDEO-OUT Vcc2 N.C. Y-TRAP Y-OUT CROMA-OUT N.C. N.C.
NC 14 73 NC A10/AP BANK #0 BANK #0 1 24 SDTI2 7 27 LOUT1
RY/BY
24 23 22 21 20 19 18 17 16 15 14 13 VCCA VCCB
GND 7 8 O5 VCC 15 72 GND Buffer 2 23 SDTI3 8 26 ROUT2
(T R) DIR VCCB
IC330~332, 339: NJM2068MD-TE2 DQM0 16 71 DQM1 MODE VCC
3 22 SDTO 9 25 LOUT2
REGISTER VSS Erase Voltage Input/Output A0 ENABLE
Dual OP-Amp. WE 17 70 NC A2 SENSE AMPLIFIER SENSE AMPLIFIER Generator Buffers R-output G-output B-output VIDEO Y-output CROMA 4 21 DAUX 10 24 ROUT3
CAS 18 69 NC ADDRESS buffer buffer buffer output buffer buffer output buffer A1 B0
BUFFER 5 20 DFS0 11 23 LOUT3
75 drive 75 drive 75 drive 75 drive 75 drive 75 drive A2 B1
12
13
14
15
16
17
18
19
20
21
22
RAS 19 68 CLK A22 WE
State 6 19
CS 20 67 CKE BYTE Control A3 B2
OUT1 1 8 +VCC 7 18
NC 21 66 A11 Y/C
SDTI4
DZFE
TVDD
DVDD
DVSS
PDN
TST1
CAD1
CAD0
LOUT4
ROUT4
A4 B3
RESET 8 17
A22 22 65 A10 Command MIX
IN1 2 7 OUT2 Register A5 B4
WP/ACC 9 16
+ + A13 23 64 A9 Program Voltage
DQ0 Generator Chip Enable buffer A6 B5
DATA CONTROL DQ STB
A12 24 63 A8 | Output Enable
Data Latch 10 15
+IN1 3 6 IN2 CIRCUIT BUFFER Y
A7 B6
A2 25 62 A7 DQ31 CE Logic
11 14
OE M GND B7
A3 26 61 A6 12 13
VCC 4 5 +IN2 REFRESH COLUMN a GND GND
A4 27 60 A5 COUNTER COUNTER R-Y
DQM0~3 t LPF R-Y
DQM2 28 59 DQM3
r modulation
Vcc 29 58 GND Y-Decoder Y-Gating i
NC 30 57 NC
STB
x B-Y A0 A1 A2 A3 A4 A5 A6 A7
B-Y
10 DQ10
GND
31
32
56
55
DQ31
VccQ Low Vcc Detector
Timer for Address
LPF
modulation
Program/Erase Latch CSYNC CSYNC CSYNC
DQ17 33 54 DQ30 COLUMN DECODER COLUMN DECODER X-Decoder Cell Matrix
DQ18 34 53 DQ29 A20 to A0 Burst generation
Phase
ROW DECODER
ROW DECODER
VccQ 35 52 GND Clamp Clamp Clamp LPF & NTSC/PAL

A-1 generation
DQ19 36 51 DQ28 selection OE
CELL ARRAY CELL ARRAY
DQ20 37 50 DQ27 BANK #0 BANK #0
GND 38 49 VccQ
DQ21 39 48 DQ26 1 2 3 4 5 6 7 8 9 10 11 12 T/R
DQ22 40 47 DQ25 GND1 R-IN G-IN B-IN N.C. fsc-IN NTSC/PAL-IN N.C. N.C. CSYNC-IN N.C. Vcc1
SENSE AMPLIFIER SENSE AMPLIFIER
VccQ 41 46 GND B0 B1 B2 B3 B4 B5 B6 B7
DQ23 42 45 DQ24
Vcc 43 44 GND
59
SCHEMATIC DIAGRAM (INPUT 1/2)

1
Page 65 G2 Page 65 K2 Page 59 G1 Page 64 J8 Page 59 C3 All voltages are measured with a 10M/V DC electronic volt meter.
to DIGITAL to POWER (4) to DIGITAL
to POWER (10) to POWER (11) Components having special characteristics are marked s and must be IC401: BD3842FS-E2
Function Switch
replaced with parts having specifications equal to those originally installed.
Schematic diagram is subject to change without notice.
1 24
2 23
10M LOGIC
3 22
s
4 21

5 20
6 19
2
7 18

8 17
5.6 -11.9
-11.6
9 16
to POWER (5)
Page 64 D7
4.8 15
4.8 -11.8 10
-11.6 11 14
FRONT L 11.1
12 13
5.0
0
0
0 0
0 0
11.8
8 5
7 0
3 0 6 0 0
to POWER (7)
IC402: BA15218F
Page 65 C3
0 0
0
0 IC408, 409: PC4570G2
-11.8 IC411: NJM2068MD-TE2
0
0 0 Dual OP-Amp.
0
-11.8 0 0
to MAIN (4)
Page 62 L9
0 0 0
0 7.0
OUT1 1 8 +VCC
0 0 0
0 0
0 -7.0 0 IN1 2 7 OUT2
-11.8 0 0 0 + +
0 0 0 -11.3 +IN1 3 6 IN2
7.0 0
-11.8 VCC 4 5 +IN2
0 2 0
1 0 11.1
0 3 0 0
4 0 0
-12.0 0
5.7
0
0
0 0 0
0 0 0
0
4 0
0 0
IC403: BD3815KS
Audio Sound Processor
5.6
0
0
0
FRONT L
GOUTFR
GOUTFL
OUTFR
GND10
BNF1R
BNF2R
OUTFL
BNF1L
BNF2L
VINFR
VINFL
GND9
TNFR
TNFL
42 41 40 39 38 37 36 35 34 33 32 31 30 29
to POWER (8)
Page 65 C5
0 0 TONE
INFRA 43 28 GND8
0
0
0
0
0
0
0
0
0
0
0
0
0
0
5.6 INFLA 44 27 OUTSW
5.6
5.6
0
0
0
0
0
0
SW1
-11.3 +
A
0 INSWA 45 +
26 GND7
0 0 0
B

0 0 0 0 0.1 INSRA 46 + 25 OUTSR
0 A
0 0 0 B +
0 INSLA 47 24 GND6
0 0
-5.7
-5.7
-5.7
0
0 +
0 CENTER INCA 48 A
B +
23 OUTSL
0 0
INSBA 49 SW2
22 GND5
0 0 +
5 0 0 INFRB 50 A
B
A
B +

21 OUTC

0 0 +
INFLB 51 20 GND4

0 0 A
A
B +
0 7.0 INSWB 52 B 19 OUTSB
0 11.1 +
SW3
0 0 INSRB 53 A
18 VCC
+
0 -7.0 0 B
A

0 INSLB 54 B +
17 GND3
0
SURROUND BACK A

SURROUND L INCB 55 B 16 VEE

to POWER (12)
Page 65 D7
INSBB 56 15 VDD
LOGIC
0
0
0
0
0
0
0
0
0
0
0
0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14
GND1
GOUTSW
VINSW
GOUTC
VINC
GOUTRR
VINRR
GOUTRL
VINRL
GND2
PORTA
PORTB
DA
CL
0
0
-11.3 0
-0.1
IC404: LC72722PM
6 RDS Signal Processor
FL OUT
VREF
C IN
11.9 18.8
1 5 6
0 -0.1
VDDA 3 PLL CLOCK 14 VDDD
(57 kHz) RECOVERY
10.5 11.8 REFERENCE
0 VOLTAGE
(1187.5 Hz)
18.8 -19.5 VSSA 4 15 VSSD
VREF
10.3
57 kHz DATA
MPX IN 2 ANTIALIASING SMOOTHING
0 -0.1 FILTER
bpf
FILTER DECODER 19 RDS-ID
-12.0 -15.0 (SCF)
to Main Transformer
DO 20
10.3 CL 21 18 SYNC
RAM ERROR CORRECTION SYNC / EC
RX-SL100: Page 63 L4
RX-SL100RDS: Page 63 L6
DI 22 CCB (24 BLOCK DATA) (SOFT DECISION) CONTROLLER 24 SYR
7.0 12.0 AC 30.6
to POWER (9)
CE 23
Page 65 C8
2.5 0 CLK (4.332 MHz)

0 4.9 T1 7 MEMORY
0 T2 8 CONTROL
7.7 18.2 TEST SYNC SYNC
4.9 0 0 AC 11.0 T3 9 OSC/DIVIDER DETECT-1 DETECT-2
T4 10
0 0 0
7 0 4.8
7.7 AC 5.9 11 16 17 13 12
2.5 0
X IN
X OUT
T5
T6
T7
0 -5.0 -18.8
0 0
5.6 11.8
0
5.0 4 5.0
-7.7
2.5
12.5
12.5
1.2
5.0
0
5.0 -7.7
6.2
-7.0 -12.2
0
12.5 0
5.0
6.2
8
0
2.5 4.7
4.8
3.3
4.8
0
2.5
4.2
4.7
0
0
3.3 4.7
2.5 3.3 4.7

0
0 0
9
x: NOT USED
O:USED / APPLICABLE
IC418: PC29M33T-E1 IC417: PQ025EN5MZPH IC416: PQ1CG21H2F IC414: NJM78M05DL1A IC413: NJM79M12DL1A IC412: NJM78M12FA IC410: PQ3RD13 IC406, 407, 419: TC74HC4053AF IC405: BD3812F-E2
Voltage Regulator Voltage Regulator Voltage Regulator Voltage Regulator IC415: NJM79M05DL1A Voltage Regulator Voltage Regulator Analog Multiplexer/Demultiplexer Audio Sound Processor
Voltage Regulator INHIBIT VDD
1 INPUT
INPUT 6 16
Vin 1 3 Vo VIN 1 2 VOUT COMMON INPUT Vin 1 2 Vo IN1 1 14 OUT1
+
Standard Voltage
Starter Circuit
Safety Drive A 11
Voltage ON/OFF INPUT STATES AGND1 2 13 OUT2
Limiter LEVEL BINARY TO 1-OF-8 "ON" CHANNEL (S)
regulator circuit B 10 INHIBIT C B A
CONVERTER DECODER WITH INHIBIT
Driver
2 Vc 4 Vc
Sudden Current
Amp. PWM COMP.

5 3 C 9 0 0 0 0 0X, 0Y, 0Z IN2 3 12 SEL
Protection
Overheat Protection
5 ON/OFF OUTPUT
3 OUTPUT GND +
OUTPUT OUTPUT GND VSS 8 0 0 0 1 1X, 0Y, 0Z +

Soft VEE 7 0 0 1 0 0X, 1Y, 0Z AGND2 4 11 DGND
start
0 0 1 1 1X, 1Y, 0Z
10 Over current F/F
Q
S
R Oscillator
0X
1X
12
13
SW
SW
14 X-COM 0 1 0 0 0X, 0Y, 1Z VEE 5 10 MUTE
protection
circuit 0 1 0 1 1X, 0Y, 1Z
Excessive Electric ERROR AMP. 0Y 2 SW 0 1 1 0 0X, 1Y, 1Z 6 LOGIC 9 DA
Current Protection 15 Y-COM AGND3
4 Oadj 1Y 1 SW
+ 0 1 1 1 1X, 1Y, 1Z
2 GND
INPUT 0Z 5 SW 1 X X X NONE VCC 7 8 CL
Over heat VREF GND 4 Z-COM
protection
COMMON 1Z 3 SW
circuit
3
COM
60
SCHEMATIC DIAGRAM (INPUT 2/2)
1
4.9
DIGITAL INPUT
2
0.2 0.2 0 0 0
4.9
Page 59 B3
to DIGITAL
3 0.2 0.2 4.9 0
4.9
0
4.9
4.9
4
2.6 3.2 0.4 0 0 4.9 0
3.2 0
0
0
0 4.9 0 0 4.9
4.9 0 0 4.9
5
IC551, 552: TC74HCU04AFEL

Hex Inverters
1A 1 14 VCC
9
1Y 2 13 6A
All voltages are measured with a 10M/V DC electronic volt meter. 2A 3 12 6Y

Components having special characteristics are marked s and must be
Schematic diagram is subject to change without notice. 2Y 4 11 5A
3A 5 10 5Y
10M
10
s 3Y 6 9 4A

GND 7 8 4Y
61
SCHEMATIC DIAGRAM (MAIN)

1
Page 63 D2 Page 63 D5 Page 63 D2 Page 63 D5 Page 63 D3 Page 63 D5
to POWER (3) to POWER (1) to POWER (3) to POWER (1) to POWER (3) to POWER (1)
IC691~693: NJM2068MD-TE2
Dual OP-Amp.
OUT1 1 8 +VCC
IN1 2 7 OUT2
+ +
+IN1 3 6 IN2
VCC 4 5 +IN2
2
SURROUND L SURROUND BACK FRONT L
IC694: TC74HCU04AFEL
4.9 4.9 4.9 Hex Inverters
4.9 0 4.9 0 4.9 0

0 0 0
1A 1 14 VCC
0 0 0
0 0 0
1Y 2 13 6A
2A 3 12 6Y
3
2Y 4 11 5A
CENTER
4.9 3A 5 10 5Y
0 0
10.2 3Y 6 9 4A
-11.0 -30.3 -10.9 -30.3
-29.8 -29.8 0 GND 7 8 4Y
4.9
-6.1
-29.8 -29.8 4.9
4 4.9
0
-40.2 -40.2
0

-10.7 -30.3 -10.8 -30.3
-29.8 -29.8 -10.9 -30.3 -10.8 -30.3
-29.8 -29.8
4.9 4.9 4.9 4.9 4.9 4.9
4.9 4.9 4.9

4.8 4.8 4.8
4.8 0.1 4.8 0.1 4.8 0.1
-29.8 -29.8
5 4.8 4.8
-29.8 -29.8
4.8
0 0 0 0 0 0
-40.2 -40.2
-40.2 -40.2
Page 59 C3
to DIGITAL
7
4.9
4.9
4.9
2.6 2.6 0 4.9 4.9 4.3
4.9
0
5
0
8 0 0 0 0 0 0
0
11.8 -11.9 11.8 -11.9 11.8 -11.9
0 2.6 2.6 0
0
0 0
0 0 0 0 0 0 0 0 0 0 0 0
to INPUT (1)
Page 60 J3
0 0
2.5 0.7
4.9 0
SURROUND L SURROUND BACK CENTER FRONT L
9
10
All voltages are measured with a 10M/V DC electronic volt meter. 10M
Components having special characteristics are marked s and must be s
62
SCHEMATIC DIAGRAM (POWER 1/3)
1
SURROUND L
Page 62 A1
to MAIN (1)
2
Page 62 E1
to MAIN (2)
SURROUND BACK
CENTER
to MAIN (3)
I1
3
Page 62
FRONT L
to INPUT (1)
Page 60 J7
5.0 5.7
5.7 8.8
B1
F1
J1
4.9 5.7
6.4
Page 62
to MAIN (1)
to MAIN (2)
to MAIN (3)
6.4
5 0
11.5
42.2
3.3 3.3 8.8 11.9 42.2

3.3 11.9
3.3 3.3
to INPUT (1)
Page 60 J7
3.8 12.3
5.0
12.3
3.8
2.3 0
2.4
0 1.7 1.7
6 42.3 -41.9
6 0
13.0
AC 61.7
13.0 0
A
12.3
B
4.8 -28.3
3.2 0 -27.7 -40.5
0 6.8 5.2
5.2
0
7 0
0 -40.5
0 0
12.8 3.7 BL
YE
10.8 12.6 15.5 3.7

Page 59 D1
12.6
to DIGITAL
AC 13.5
8 11.4
8.7
11.9
4.0 3.9
12.6
12.9
4.9
5.0
0 0
0
11.4
0
0 AC 8.9
11.4 0.5 15.5
0.1 0.7
0
0 0.1 0.6 0
0
0
9
Point 6 emitter of Q9 and collector of Q4
x: NOT USED
A Q9 E
All voltages are measured with a 10M/V DC electronic volt meter. IC1: PQ05RA1
Components having special characteristics are marked s and must be Voltage Regulator
10 Vin 1 2 Vo
B Q4 C
10M
s
4 Vc
3
POWER ON POWER OFF
GND (Connect the power cable) (Disconnect the power cable)
63

1
-20.1
-20.1
-20.1
-20.1
-25.7
-23.8
-23.6
-21.8
-19.9
-23.7
-25.6
-17.9
-21.9
-14.2
-21.9
-23.7
-23.7
-25.7
-23.7
-23.7
-23.8
-19.8
-23.8
-23.7
-23.7
-25.7
-27.6
FL DISPLAY
-25.6
-14.1
-18.0
-18.1
-27.6
-20.0
-20.0
-19.9
-23.7
-23.8
-27.6
-23.7
-29.6
-21.7
-23.8
-25.9
-25.7
-25.7
-25.7
-25.8
-25.7
-25.8
-25.7
-25.7
-25.7
-25.7
-25.7
-25.8
-25.8
-25.7
-25.7
-20.1
-20.1
-20.1
-20.1
STANDBY/ON
4.9 4.9
3
-23.7
-25.7
-23.7
-23.7
-21.9
-14.2
-21.9
-17.9
-25.7
-23.7
-19.9
-21.8
-23.6
-23.8
-25.7
4.9
-23.6 -25.7
-23.7 -25.6
-25.7 -27.6
-20.3
-23.8 -25.7
-21.7 -23.7
-27.6 -23.6 -27.8
-23.7 -23.8
-27.6
FL DRIVER -19.8
-23.8 -23.8
4.9
-23.7 -23.7
4 4.9
-19.9
4.9
3.8 -20.0
2.1
3.8 -20.0
4.9 4.9 2.2
4.9
4.9 -27.6
0
0 0 -18.1 0
Page 59 E1 -25.7 -25.7 -18.0 4.9
to DIGITAL
4.9
-25.7 -25.6 -14.1 4.6
-25.7
4.6
-25.7
-25.7
-25.8
-25.7
-25.7
-25.7
-25.7
-25.7
-25.7
-25.8
-25.7
-25.8
-25.7
-25.7
-25.7
-27.8
4.6
4.9
4.6
4.9
6
4.9 IR REMOTE
4.9
VOLUME/SELECT
to INPUT (1)
Page 60 A2
Page 59 E1 Page 60 G1 IC101: M66003-0101FP

to DIGITAL to INPUT (1) FL Display Driver
Display code
RAM CGROM
(35 bit x 166) 44 P35
(8-bit x 60)
Code Segment 19 P10
write output
9 circuit
17 P9
dot data
CGROM 9 P1
/CEFL 2 Serial data (35 bit x 16)
write
CKFL 3 receive
circuit Code/
DTFL 4 command
control 45 P36
circuit
52 G12
51 G13
code Segment
select 50 G14
digit
select/ 49 G15I
XIN 7 Clock output
timing Display
generator clock controller scan pulse circuit 48 G16I
XOUT 6
All voltages are measured with a 10M/V DC electronic volt meter.
Components having special characteristics are marked s and must be 47 P38
replaced with parts having specifications equal to those originally installed. 46 P37
10 Schematic diagram is subject to change without notice.
63 G1
Digit
/RESET 1 output
circuit
10M VDD 8 53 G11
s VDD 18
Vss 5

Vp 64

64
1
to INPUT (1)
Page 60 C1
to INPUT (1)
Page 60 B1
3
to INPUT (1)
Page 60 A3
Page 59 J1
to DIGITAL
0
0
0 0
0.6
0
0 0 0
to INPUT (1)
Page 60 A4
0
5 0 0
10.8
2.0
2.0
2.0
5.0
0.7
0
0
0
0 10.8
0.6
0
10.7
0 0
0.7
2.0
4.9
2.0
5.0
0.6
0
0
x: NOT USED
0.8 4.5
0.8 5.2
6.4 10.8
7 6.3
to INPUT (1)
0.2 5.7
Page 60 A6
10.8
0.2 5.1 IC303~304: BA7613N
Video Signal Selector
0.2 0 5.1
0.2 0 5.1
1.0 0
1.1 0
MUTE
6dB Amp. 75ohm Driver
to INPUT (1)
Page 60 A7
Logic
8
1 2 3 4 5 6 7 8
IN1
CTLA
CTLB
IN2
GND
IN3
Vcc
Vout
IC301: BD3842FS-E2
Function Switch
1 24
IC261: TC74HC4051AFEL IC281: LA7108M IC282: NJM2233BM
9 Analog Multiplexer/Demultiplexer Video Amp Video Switch 2 23
GND VOUT V+ N.C. LOGIC
INHIBIT VCC
8 7 6 5 3 22
6 16
VIN1+ 1 16 +VCC
A 11 INPUT STATES 4 21
LEVEL BINARY TO 1-OF-8 "ON" CHANNEL 2
BUFFER
INHIBIT C B A NFB1 6dB DR 15 VOUT1
B 10
CONVERTER DECODER WITH INHIBIT
0 0 0 0 0 5 20
C 9
3
0 0 0 1 1 MUTE1 14 GND
GND 8
BIAS
0 0 1 0 2 6 19
VEE 7
15k
0 0 1 1 3 VIN2+ 4 13 VOUT2
0 13 SW 3 COM
0 1 0 0 4 6dB DR 15k 7 18
1 14 SW 0 1 0 1 5 NFB2 5 12 MUTE2
2 15 SW 0 1 1 0 6 1 2 3 4 17
8
3 12 SW 0 1 1 1 7 6 VIN1 SW1 VIN2 N.C.
-VCC1 11 VOUT3
10 4 1 SW 1 X X X NONE
9 16
All voltages are measured with a 10M/V DC electronic volt meter. 10M 5 5 SW VIN3+ 7 6dB DR 10 MUTE3
Components having special characteristics are marked s and must be s 6 2 SW 10 15
replaced with parts having specifications equal to those originally installed. 7 4 SW NFB3 8 9 -VCC2
Schematic diagram is subject to change without notice. 11 14
12 13
65
PARTS LIST
ELECTRICAL PARTS
WARNING
Components having special characteristics are marked s and must be replaced with parts having specifications equal to
those originally installed.
ABBREVIATIONS IN THIS LIST ARE AS FOLLOWS:
C.A.EL.CHP : CHIP ALUMI.ELECTROLYTIC CAP L.EMIT : LIGHT EMITTING MODULE

C.CE : CERAMIC CAP LED.DSPLY : LED DISPLAY
C.CE.ARRAY : CERAMIC CAP ARRAY LED.INFRD : LED,INFRARED
C.CE.CHP : CHIP CERAMIC CAP MODUL.RF : MODULATOR,RF
C.CE.ML : MULTILAYER CERAMIC CAP PHOT.CPL : PHOTO COUPLER
C.CE.M.CHP : CHIP MULTILAYER CERAMIC CAP PHOT.INTR : PHOTO INTERRUPTER
C.CE.SAFTY : RECOGNIZED CERAMIC CAP PHOT.RFLCT : PHOTO REFLECTOR
C.CE.TUBLR : CERAMIC TUBULAR CAP PIN.TEST : PIN,TEST POINT
C.CE.SMI : SEMI CONDUCTIVE CERAMIC CAP PLST.RIVET : PLASTIC RIVET
C.EL : ELECTROLYTIC CAP R.ARRAY : RESISTOR ARRAY
C.MICA : MICA CAP R.CAR. : CARBON RESISTOR
C.ML.FLM : MULTILAYER FILM CAP R.CAR.CHP : CHIP RESISTOR
C.MP : METALLIZED PAPER CAP R.CAR.FP : FLAME PROOF CARBON RESISTOR
C.MYLAR : MYLAR FILM CAP R.FUS : FUSABLE RESISTOR
C.MYLAR.ML : MULTILAYER MYLAR FILM CAP R.MTL.CHP : CHIP METAL FILM RESISTOR
C.PAPER : PAPER CAPACITOR R.MTL.FLM : METAL FILM RESISTOR
C.PLS : POLYSTYRENE FILM CAP R.MTL.OXD : METAL OXIDE FILM RESISTOR
C.POL : POLYESTER FILM CAP R.MTL.PLAT : METAL PLATE RESISTOR
C.POLY : POLYETHYLENE FILM CAP RSNR.CE : CERAMIC RESONATOR
C.PP : POLYPROPYLENE FILM CAP RSNR.CRYS : CRYSTAL RESONATOR
C.TNTL : TANTALUM CAP R.TW.CEM : TWIN CEMENT FIXED RESISTOR
C.TNTL.CHP : CHIP TANTALUM CAP R.WW : WIRE WOUND RESISTOR
C.TRIM : TRIMMER CAP SCR.BND.HD : BIND HEAD B-TITE SCREW
CN : CONNECTOR SCR.BW.HD : BW HEAD TAPPING SCREW
CN.BS.PIN : CONNECTOR,BASE PIN SCR.CUP : CUP TITE SCREW
CN.CANNON : CONNECTOR,CANNON SCR.TERM : SCREW TERMINAL
CN.DIN : CONNECTOR,DIN SCR.TR : SCREW,TRANSISTOR
CN.FLAT : CONNECTOR,FLAT CABLE SUPRT.PCB : SUPPORT,P.C.B.
CN.POST : CONNECTOR,BASE POST SURG.PRTCT : SURGE PROTECTOR
COIL.MX.AM : COIL,AM MIX SW.TACT : TACT SWITCH
COIL.AT.FM : COIL,FM ANTENNA SW.LEAF : LEAF SWITCH
COIL.DT.FM : COIL,FM DETECT SW.LEVER : LEVER SWITCH
COIL.MX.FM : COIL,FM MIX SW.MICRO : MICRO SWITCH
COIL,OUTPT : OUTPUT COIL SW.PUSH : PUSH SWITCH
DIOD.ARRAY : DIODE ARRAY SW.RT.ENC : ROTARY ENCODER
DIODE.BRG : DIODE BRIDGE SW.RT.MTR : ROTARY SWITCH WITH MOTOR
DIODE.CHP : CHIP DIODE SW.RT : ROTARY SWITCH
DIODE.VAR : VARACTOR DIODE SW.SLIDE : SLIDE SWITCH
DIOD.Z.CHP : CHIP ZENER DIODE TERM.SP : SPEAKER TERMINAL
DIODE.ZENR : ZENER DIODE TERM.WRAP : WRAPPING TERMINAL
DSCR.CE : CERAMIC DISCRIMINATOR THRMST.CHP : CHIP THERMISTOR
FER.BEAD : FERRITE BEADS TR.CHP : CHIP TRANSISTOR
FER.CORE : FERRITE CORE TR.DGT : DIGITAL TRANSISTOR
FET.CHP : CHIP FET TR.DGT.CHP : CHIP DIGITAL TRANSISTOR
FL.DSPLY : FLUORESCENT DISPLAY TRANS : TRANSFORMER
FLTR.CE : CERAMIC FILTER TRANS.PULS : PULSE TRANSFORMER
FLTR.COMB : COMB FILTER MODULE TRANS.PWR : POWER TRANSFORMER ASSY
FLTR.LC.RF : LC FILTER,EMI TUNER.AM : TUNER PACK,AM
GND.MTL : GROUND PLATE TUNER.FM : TUNER PACK,FM
GND.TERM : GROUND TERMINAL TUNER.PK : FRONT-ENDTUNER PACK
HOLDER.FUS : FUSE HOLDER VR : ROTARY POTENTIOMETER
IC.PRTCT : IC PROTECTOR VR.MTR : POTENTIOMETER WITH MOTOR
JUMPER.CN : JUMPER CONNECTOR VR.SW : POTENTIOMETER WITH ROTARY SW
JUMPER.TST : JUMPER,TEST POINT VR.SLIDE : SLIDE POTENTIOMETER
L.DTCT : LIGHT DETECTING MODULE VR.TRIM : TRIMMER POTENTIOMETER
Note) Those parts marked with # are not included in the P.C.B. assy.
67
P.C.B. DIGITAL
Schm
Ref. PART NO. Description Remarks Markets Rank
* WC277200 P.C.B. DIGITAL J
* WC277300 P.C.B. DIGITAL UCRK
* WC277400 P.C.B. DIGITAL BG
* WC277500 P.C.B. DIGITAL TAL
* CB301 WC196500 CN 15P TE FMN
CB306 WC199000 CN 40P TE FMN
* CB307 WC196500 CN 15P TE FMN BG
D303 WB081800 DIODE SB01-05Q
D304 WB081800 DIODE SB01-05Q
D305 WB081800 DIODE SB01-05Q
D306 WB081800 DIODE SB01-05Q
D307 VU171900 DIODE.ZENR UDZ5.1B 5.1V 01
D310 WB081800 DIODE SB01-05Q
G1 WB438000 TERM.GND M4 SD00433-21
G2 WB438000 TERM.GND M4 SD00433-21
G3 WB438000 TERM.GND M4 SD00433-21
G4 WB438000 TERM.GND M4 SD00433-21
IC301 XW433A00 IC CY62256LL-70SNCT J 05
IC302 XV077B00 IC MSM514260E-60JS 07

IC303 X4075B00 IC XC9572XL-10Q100C J 07
IC304 X0238B00 IC YSS938 13
IC305 X3473A00 IC CS493292-CLR J 15
* IC305 X3939A00 IC CS493264-CL UCRTKBG
IC306 X3807A00 IC AK4628VQ
IC307 X2965A00 IC.CPU M30805SGP 09
* IC310 X3097A00 IC 74LVX4245MTCX 03
* IC311 X3097A00 IC 74LVX4245MTCX 03
* IC312 X3097A00 IC 74LVX4245MTCX 03
* IC313 X3097A00 IC 74LVX4245MTCX 03
* IC314 X3097A00 IC 74LVX4245MTCX 03
IC315 X2314A00 IC MB3516APF-G-BND 04
* IC316 X4924B00 IC.EPROM MBM29LV320BE90T written
IC317 X2479A00 IC YGV619 12
IC318 X0176A00 IC W986432DH-7 SDRAM 15
* IC329 X3586A00 IC TC74VHCT08AFT AND
IC330 X3505A00 IC NJM2068MD-TE2 02
IC331 X3505A00 IC NJM2068MD-TE2 02
IC332 X3505A00 IC NJM2068MD-TE2 02
IC333 X3542A00 IC 74LCX07MTCX 01
IC334 X3724A00 IC 74VHC00MTCX 01
IC335 X3724A00 IC 74VHC00MTCX 01
IC336 X3542A00 IC 74LCX07MTCX UCRTKBG 01
* IC337 X5191A00 IC 74VHC153MTC UCRTKBG
IC339 X3505A00 IC NJM2068MD-TE2 02
* IC340 X3097A00 IC 74LVX4245MTCX 03
XL301 V3625700 RSNR.CRYS 24.576MHz 03
New Parts #
68
P.C.B. DIGITAL & P.C.B. INPUT

Schm
* XL302 V9460000 RSNR.CE 20MHz CSTCW20M0X53 01
* XL303 WC061400 RSNR.CRYS 14.31818MHz SMD-49 JUCRK
XL303 V6074900 RSNR.CRYS 17.734475MHz TABGL 03
* WC276400 P.C.B. INPUT J

* WC276500 P.C.B. INPUT UC
* WC276600 P.C.B. INPUT R
* WC276700 P.C.B. INPUT TA
* WC276800 P.C.B. INPUT K
* WC276900 P.C.B. INPUT BG
* WC277000 P.C.B. INPUT L
CB401 VB390400 CN.BS.PIN 8P 01
CB402 V7825800 CN 8P TE TUC SERIES JUCRTKA
CB403 V7825900 CN 9P TE TUC SERIES JUCRTKA
CB404 VN394900 CN.BS.PIN 14P BG 01
CB405 V7825400 CN 4P TE TUC SERIES BG 01
CB406 VM923600 CN.BS.PIN 13P 01
CB407 V7826000 CN 10P TE TUC SERIES JUCRTKA 01
CB408 V7826200 CN 12P TE TUC SERIES JUCRTKA 01
* CB409 WB497000 CN.BS.PIN 40P TE FMN
CB410 VQ046900 CN.BS.PIN 5P 01
CB411 V7414400 CN 15P TE FMN 01
CB412 VM973500 CN.BS.PIN 17P 01
* CB413 LB918070 CN.BS.PIN 7P 01
CB552 V7414400 CN 15P TE FMN 01
C412 UM397100 C.EL 10uF 16V 01
C413 UM397100 C.EL 10uF 16V 01
C414 UN866330 C.EL 3.3uF 50V 01
C415 UR867330 C.EL 33uF 50V 01
C416 UR867330 C.EL 33uF 50V BG 01
C423 UR866220 C.EL 2.2uF 50V 01
C424 UR866220 C.EL 2.2uF 50V BG 01
C425 UM397100 C.EL 10uF 16V 01
C426 UM397100 C.EL 10uF 16V 01
C427 UR867330 C.EL 33uF 50V BG 01
C428 UM397100 C.EL 10uF 16V 01
C431 UM397100 C.EL 10uF 16V 01
C438 UM397100 C.EL 10uF 16V 01
C440 UM397100 C.EL 10uF 16V 01
C441 UM397100 C.EL 10uF 16V 01
C442 UM397100 C.EL 10uF 16V 01
C443 UM397100 C.EL 10uF 16V 01
C444 UA653470 C.MYLAR 4700pF 50V 01
C445 UM397100 C.EL 10uF 16V 01
C446 UR837470 C.EL 47uF 16V BG 01
C447 UA653470 C.MYLAR 4700pF 50V 01
C448 UM397100 C.EL 10uF 16V 01
C449 UA655180 C.MYLAR 0.18uF 50V 01
C451 UA655150 C.MYLAR 0.15uF 50V 01
C452 UM397100 C.EL 10uF 16V 01
New Parts #
69
P.C.B. INPUT
Schm
C453 UR837470 C.EL 47uF 16V BG 01
C454 UA655180 C.MYLAR 0.18uF 50V 01
C455 UA655150 C.MYLAR 0.15uF 50V 01
C459 UM397100 C.EL 10uF 16V 01
C462 UR837470 C.EL 47uF 16V BG 01
C465 UM397220 C.EL 22uF 25V 01
C466 UM397330 C.EL 33uF 16V 01
C467 UM416220 C.EL 2.2uF 50V 01
C468 UM417100 C.EL 10uF 50V 01
C469 UM417100 C.EL 10uF 50V 01
C470 UM397100 C.EL 10uF 16V 01
C471 UM397100 C.EL 10uF 16V 01
C472 UR867470 C.EL 47uF 50V 01
C473 UR867470 C.EL 47uF 50V 01
C476 UA652100 C.MYLAR 100pF 50V 01
C477 UA652100 C.MYLAR 100pF 50V 01
C478 UA652100 C.MYLAR 100pF 50V 01
C480 UR867470 C.EL 47uF 50V 01
C481 UR867470 C.EL 47uF 50V 01
C482 UR838100 C.EL 100uF 16V 01
C484 UR867470 C.EL 47uF 50V 01
C485 UR867470 C.EL 47uF 50V 01
C486 V7409000 C.EL 180uF 16V 02
C487 UA654270 C.MYLAR 0.027uF 50V 01
C488 UA654270 C.MYLAR 0.027uF 50V 01
C489 UM397100 C.EL 10uF 16V 01

C490 UM397100 C.EL 10uF 16V 01
C491 UM397100 C.EL 10uF 16V 01
C492 UA654270 C.MYLAR 0.027uF 50V 01
C493 UA654270 C.MYLAR 0.027uF 50V 01
C494 VR193400 C.OS 10uF 25V 03
C497 UA652100 C.MYLAR 100pF 50V 01
C498 UR838100 C.EL 100uF 16V 01
C499 UR838100 C.EL 100uF 16V 01
C500 UR819100 C.EL 1000uF 6.3V 01
C504 UR819100 C.EL 1000uF 6.3V 01
C505 UT652100 C.PP 100pF 100V 01
C506 UT652100 C.PP 100pF 100V 01
C508 UR848470 C.EL 470uF 25V 01
C509 UR848100 C.EL 100uF 25V 01
C510 UR848100 C.EL 100uF 25V JUCRTKA 01
C517 UR838100 C.EL 100uF 16V 01
C518 UR838100 C.EL 100uF 16V 01
C519 UR838100 C.EL 100uF 16V 01
C520 UM397470 C.EL 47uF 16V 01
C521 UM397470 C.EL 47uF 16V 01
C523 UN866330 C.EL 3.3uF 50V 01
C524 UR818470 C.EL 470uF 6.3V 01
C525 UR749470 C.EL 4700uF 25V 05
C526 UR749470 C.EL 4700uF 25V 05
C527 WC019400 C.EL 10000uF 16V
C528 UR818100 C.EL 100uF 6.3V 01
New Parts #
70
P.C.B. INPUT
Schm
C529 UM397100 C.EL 10uF 16V 01
C530 UM397100 C.EL 10uF 16V 01
C533 UA655100 C.MYLAR 0.1uF 50V 01
C534 UA655100 C.MYLAR 0.1uF 50V 01
C535 UR818470 C.EL 470uF 6.3V 01
C536 UM397100 C.EL 10uF 16V JUCRTKA 01
C537 UM397100 C.EL 10uF 16V JUCRTKA 01
C540 UR866100 C.EL 1uF 50V 01
C541 UA655100 C.MYLAR 0.1uF 50V 01
C542 UM397100 C.EL 10uF 16V 01
C543 UM397100 C.EL 10uF 16V 01
C544 UM397100 C.EL 10uF 16V 01
C545 UM397100 C.EL 10uF 16V 01
C546 UN866330 C.EL 3.3uF 50V 01
C547 UN866330 C.EL 3.3uF 50V 01
C548 UR819100 C.EL 1000uF 6.3V 01
C555 UR867220 C.EL 22uF 50V 01
C561 UR819100 C.EL 1000uF 6.3V 01
C562 UR838100 C.EL 100uF 16V 01
D401 VT332900 DIODE 1SS355 01
D402 VU995500 DIODE.ZENR MA8100-H 10.3V 02
D403 VU993000 DIODE.ZENR MA8056-M 5.6V BG 01
D404 VU994300 DIODE.ZENR MA8075-H 7.7V
D405 VU994300 DIODE.ZENR MA8075-H 7.7V
D406 VT332900 DIODE 1SS355 01
D407 VV220700 DIODE.SHOT RB501V-40 01
D408 VV220700 DIODE.SHOT RB501V-40 JUCRTKA 01
D409 V6267600 DIODE RB051L-40 01
D410 VT332900 DIODE 1SS355 01
D411 VT332900 DIODE 1SS355 01
D412 VU172000 DIODE.ZENR UDZS5.6BTE-17 5.6V 01
D413 VU172000 DIODE.ZENR UDZS5.6BTE-17 5.6V 01
D414 VT332900 DIODE 1SS355 01
D415 VT332900 DIODE 1SS355 01
s D416 VR253700 DIODE.BRG S1NB20 1A 200V 02
s D417 V4269600 DIODE.BRG D2SBA20 1.5A 200V
D418 VT332900 DIODE 1SS355 01
D419 VT332900 DIODE 1SS355 01
D420 VT332900 DIODE 1SS355 01
D551 VT332900 DIODE 1SS355 01
D552 VT332900 DIODE 1SS355 01
IC401 X4258A00 IC BD3842FS-E2 JUCRTKA
IC402 XS377A00 IC BA15218F OP AMP 01
IC403 X3546A00 IC BD3815KS
* IC404 X0082A00 IC LC72722PM BG
IC405 X3545A00 IC BD3812F-E2
IC406 XY879A00 IC TC74HC4053AF(EL) 03
IC408 XF291A00 IC uPC4570G2 03
IC409 XF291A00 IC uPC4570G2 03
s IC410 XY045A00 IC PQ3RD13 3.3V1A 03
IC411 X3505A00 IC NJM2068MD-TE2 02
s IC412 XJ602A00 IC NJM78M12FA 02
New Parts #
71
P.C.B. INPUT
Schm
*s IC413 X2593A00 IC NJM79M12DL1A(TE1) 02
*s IC414 XS534A00 IC NJM78M05DL1A(TE1) JUCRTKA 02
*s IC415 X4822A00 IC NJM79M05DL1A JUCRTKA
s IC416 XY455A00 IC PQ1CG21H2F SW 04
* IC417 X5052A00 IC PQ025EN5MZPH
IC418 XU965A00 IC uPC29M33T-E1 3.3V 03
IC551 XD598A00 IC TC74HCU04AFEL INV 01
* L403 WB754900 COIL LHFP13BB680K
PJ551 V4483900 JACK.PIN 1P YKC21-3895
Q401 VV655000 TR.DGT DTA114EKA 01
s Q402 VV556400 TR 2SC2412K Q,R,S 01
s Q403 VV556400 TR 2SC2412K Q,R,S BG 01
Q404 VZ725900 TR 2SD1938F S,T
Q405 VZ725900 TR 2SD1938F S,T
Q406 VZ725900 TR 2SD1938F S,T
Q407 VZ725900 TR 2SD1938F S,T
Q408 iC1815I0 TR 2SC1815 Y 01
Q409 iA1015I0 TR 2SA1015 Y 01
Q411 VD303700 TR 2SC3326 A,B 01
Q412 VD303700 TR 2SC3326 A,B 01
Q413 VD303700 TR 2SC3326 A,B 01
Q414 VD303700 TR 2SC3326 A,B 01
Q415 VD303700 TR 2SC3326 A,B 01

Q416 VD303700 TR 2SC3326 A,B 01
R403 HV753100 R.CAR.FP 1 1/4W 01
R417 HV753100 R.CAR.FP 1 1/4W JUCRTKA 01
R434 HV753100 R.CAR.FP 1 1/4W 01
R435 HV753100 R.CAR.FP 1 1/4W 01
R439 HV753100 R.CAR.FP 1 1/4W 01
R440 HV753100 R.CAR.FP 1 1/4W 01
* R469 WB784600 R.MTL.FLM 3.9 1W
R470 VP940200 R.MTL.OXD 47 1W 01
R471 HV753100 R.CAR.FP 1 1/4W 01
R472 HV753100 R.CAR.FP 1 1/4W 01
R475 HV753100 R.CAR.FP 1 1/4W 01
R476 HV753100 R.CAR.FP 1 1/4W 01
R493 VP940200 R.MTL.OXD 47 1W 01
R505 VU224000 R.MTL.FLM 0.22 1W 01
* R506 WB785400 R.MTL.OXD 180 1W JUCRTKA
R507 VP940600 R.MTL.OXD 220 1W JUCRTKA 01
U551 WB001400 CN.PHOT.SN 1P GP1FA553RZ 04
U552 WB001400 CN.PHOT.SN 1P GP1FA553RZ 04
XL401 V3930900 RSNR.CRYS 4.332MHz BG 05
EG330360 SCR.BND.HD 3x6 MFZN2BL 01
New Parts #
72
P.C.B. MAIN
Schm
* WC275400 P.C.B. MAIN
CB601 LB919030 CN.BS.PIN 3P 01
CB602 V7827500 SOCKET 8P SE TUC SERIES
CB691 V7825800 CN 8P TE TUC SERIES
CB692 V7825900 CN 9P TE TUC SERIES
CB693 V7826000 CN 10P TE TUC SERIES 01
* CB694 WB832600 CN 6P TE
CB695 VF982300 CN.BS.PIN 17P 01
C601 UR838100 C.EL 100uF 16V 01
C602 UR857100 C.EL 10uF 35V 01
C603 UR857100 C.EL 10uF 35V 01
C604 UR857100 C.EL 10uF 35V 01
C605 UR857100 C.EL 10uF 35V 01
C631 UR838100 C.EL 100uF 16V 01
C632 UR857100 C.EL 10uF 35V 01
C633 UR857100 C.EL 10uF 35V 01
C634 UR857100 C.EL 10uF 35V 01
C635 UR857100 C.EL 10uF 35V 01
C661 UR838100 C.EL 100uF 16V 01
C662 UR857100 C.EL 10uF 35V 01
C663 UR857100 C.EL 10uF 35V 01
C664 UR857100 C.EL 10uF 35V 01
C665 UR857100 C.EL 10uF 35V 01
C694 UM397470 C.EL 47uF 16V 01
C695 UM397470 C.EL 47uF 16V 01
C717 UR838100 C.EL 100uF 16V 01
D603 VT332900 DIODE 1SS355 01
D604 VT332900 DIODE 1SS355 01
D605 VT332900 DIODE 1SS355 01
D633 VT332900 DIODE 1SS355 01
D634 VT332900 DIODE 1SS355 01
D635 VT332900 DIODE 1SS355 01
New Parts #
73
P.C.B. MAIN
Schm
D663 VU996200 DIODE.ZENR MA8120-M 12.0V 01
D665 VT332900 DIODE 1SS355 01
D666 VT332900 DIODE 1SS355 01
D667 VT332900 DIODE 1SS355 01
IC691 X3505A00 IC NJM2068MD-TE2 02
IC692 X3505A00 IC NJM2068MD-TE2 02
IC693 X3505A00 IC NJM2068MD-TE2 02
PN601 V9637500 PIN L=70 #18
Q601 VV556400 TR 2SC2412K Q,R,S 01
Q602 Vi334100 TR 2SD1760 F5 P,Q,R 01
Q603 Vi334100 TR 2SD1760 F5 P,Q,R 01
Q604 VV556400 TR 2SC2412K Q,R,S 01
Q605 VV556400 TR 2SC2412K Q,R,S 01
Q631 VV556400 TR 2SC2412K Q,R,S 01
Q632 Vi334100 TR 2SD1760 F5 P,Q,R 01
Q633 Vi334100 TR 2SD1760 F5 P,Q,R 01
Q634 VV556400 TR 2SC2412K Q,R,S 01
Q635 VV556400 TR 2SC2412K Q,R,S 01
Q661 VV556400 TR 2SC2412K Q,R,S 01
Q662 Vi334100 TR 2SD1760 F5 P,Q,R 01
Q663 Vi334100 TR 2SD1760 F5 P,Q,R 01
Q664 VV556400 TR 2SC2412K Q,R,S 01
Q665 VV556400 TR 2SC2412K Q,R,S 01

Q667 VV655400 TR.DGT DTC114EKA 01
Q691 VV556500 TR 2SA1037K Q,R,S 01
Q692 VV556500 TR 2SA1037K Q,R,S 01
Q693 VV556400 TR 2SC2412K Q,R,S 01
Q694 VV556400 TR 2SC2412K Q,R,S 01
Q695 VV556400 TR 2SC2412K Q,R,S 01
R603 VP940900 R.MTL.OXD 560 1W
R604 VP940900 R.MTL.OXD 560 1W
R633 VP940900 R.MTL.OXD 560 1W
R634 VP940900 R.MTL.OXD 560 1W
R663 VP940900 R.MTL.OXD 560 1W
R664 VP940900 R.MTL.OXD 560 1W
R722 HV754100 R.CAR.FP 10 1/4W 01
R723 HV754100 R.CAR.FP 10 1/4W 01
ST601 WA246200 SCR.TERM 3.5
ST691 V4040500 SCR.TERM M3 01
s TH661 WC310100 THRMST NTSA0WF104FN6A0
* XL691 WB924700 RSNR.CE 375KHz CSBLA375K
* XL692 WC511200 RSNR.CE 420K CSBLA420KECE
New Parts #
74
P.C.B. POWER
Schm
* WC275600 P.C.B. POWER J
* WC275700 P.C.B. POWER UC
* WC275800 P.C.B. POWER R
* WC275900 P.C.B. POWER TK
* WC276000 P.C.B. POWER A
* WC276100 P.C.B. POWER BG
* WC276200 P.C.B. POWER L
CB4 VB389800 CN.BS.PIN 2P 01
* CB5 WA894400 CN.BS.PIN 18P TE FMN
CB7 VP206500 HOLDER.FUS EYF-52BCT 01
CB8 VP206500 HOLDER.FUS EYF-52BCT 01
s CB9 VT807100 CN.BS.PIN 2P 01
s CB10 VG879900 CN.BS.PIN 2P 01
* CB51 LB933050 CN.BS.PIN 5P SE VH BG 01
* CB72 LB919050 CN.BS.PIN 5P 01
* CB104 V6217900 CN.BS.PIN 10P TE FMN
CB106 Vi878100 CN.BS.PIN 3P 01
CB161 V6217800 CN.BS.PIN 8P TE FMN 01
CB201 V7827500 SOCKET 8P SE TUC SERIES JUCRTKA
CB241 V7827100 SOCKET 4P TE TUC SERIES BG
CB281 V7827900 SOCKET 12P TE TUC SERIES JUCRTKA
CB301 VF982200 CN.BS.PIN 14P BG 02
CB302 WA247900 CN 21P YKF41-5038 BG 03
* CB303 V7414100 CN 15P SE FMN BG
* CB304 WB497100 CN 21P YKF41-5044 BG
C2 UR867100 C.EL 10uF 50V 01
C3 UR866220 C.EL 2.2uF 50V 01
C4 UR837100 C.EL 10uF 16V BG 01
C5 UR837100 C.EL 10uF 16V BG 01
C7 VF992600 C.EL 4700uF 5.5V 02
C8 UR819100 C.EL 1000uF 6.3V 01
C9 UR867100 C.EL 10uF 50V 01
C10 UR866100 C.EL 1uF 50V 01
C11 UR866220 C.EL 2.2uF 50V 01
C13 V7409000 C.EL 180uF 16V BG 02
C14 UR839100 C.EL 1000uF 16V 01
C15 UR839100 C.EL 1000uF 16V BG 01
C16 UR867470 C.EL 47uF 50V 01
C17 UR867470 C.EL 47uF 50V 01
C18 UR867220 C.EL 22uF 50V 01
C19 UR867470 C.EL 47uF 50V 01
C20 UR848100 C.EL 100uF 25V 01
C21 UR866470 C.EL 4.7uF 50V 01
C22 UR867100 C.EL 10uF 50V 01
New Parts #
75
P.C.B. POWER
Schm
* s C23 WC272500 C.EL 6800uF 50V
* s C24 WC272500 C.EL 6800uF 50V
C26 VR325100 C.MYLAR 0.01uF 100V 01
C27 VT898000 C.MYLAR 0.1uF 100V
C28 VT898000 C.MYLAR 0.1uF 100V
s C29 V6185300 C.CE.SAFTY 0.01uF 275V
C30 UR866100 C.EL 1uF 50V 01
C31 UR866100 C.EL 1uF 50V 01
C32 VF992600 C.EL 4700uF 5.5V 02
C33 UR818470 C.EL 470uF 6.3V 01
C34 UR819100 C.EL 1000uF 6.3V 01
C35 UR819100 C.EL 1000uF 6.3V 01
C77 UA654100 C.MYLAR 0.01uF 50V 01
C78 UA654100 C.MYLAR 0.01uF 50V 01
C79 UA654100 C.MYLAR 0.01uF 50V 01
C80 UA654100 C.MYLAR 0.01uF 50V 01
C81 UA654100 C.MYLAR 0.01uF 50V 01
C82 UA654100 C.MYLAR 0.01uF 50V 01
C120 UM388330 C.EL 330uF 6.3V 01
C169 UR837470 C.EL 47uF 16V 01

C285 UR818220 C.EL 220uF 6.3V JUCRTKA 01
C305 UR837100 C.EL 10uF 16V BG 01
C306 UR837100 C.EL 10uF 16V BG 01
C307 UR837100 C.EL 10uF 16V BG 01
C308 UR837100 C.EL 10uF 16V BG 01
C309 UR837100 C.EL 10uF 16V BG 01
C310 UR837100 C.EL 10uF 16V BG 01
C311 UR837100 C.EL 10uF 16V BG 01
C312 UR837100 C.EL 10uF 16V BG 01
C313 UR837100 C.EL 10uF 16V BG 01
C314 UR837100 C.EL 10uF 16V BG 01
C315 UR837100 C.EL 10uF 16V BG 01
C316 UR837100 C.EL 10uF 16V BG 01
C317 UR837100 C.EL 10uF 16V BG 01
C319 UR837100 C.EL 10uF 16V BG 01
C321 UR837100 C.EL 10uF 16V BG 01
C322 UR838100 C.EL 100uF 16V BG 01
C340 UR867100 C.EL 10uF 50V BG 01
C341 UR819100 C.EL 1000uF 6.3V BG 01
New Parts #
76
P.C.B. POWER
Schm
C342 UR867100 C.EL 10uF 50V BG 01
C343 UR867100 C.EL 10uF 50V BG 01
C344 UR867100 C.EL 10uF 50V BG 01
C345 UR819100 C.EL 1000uF 6.3V BG 01
D1 VU992200 DIODE.ZENR MA8047-M 4.7V
* D2 VU995900 DIODE.ZENR MA8110-H 11.3V BG
D3 VV833200 DIODE 1SS380 01
D4 VV307700 DIODE 1N4002S 01
D5 VT332900 DIODE 1SS355 BG 01
D6 VT332900 DIODE 1SS355 01
D7 VT332900 DIODE 1SS355 BG 01
D9 VT332900 DIODE 1SS355 01
D11 VU999500 DIODE.ZENR MA8270-M 27V 01
s D12 VR253700 DIODE.BRG S1NB20 1A 200V 02
D13 VT532500 DIODE 1SR154-400 01
D14 VT532500 DIODE 1SR154-400 01
s D15 VN011400 DIODE.BRG D5SB20 5A 200V 03
D16 VT332900 DIODE 1SS355 01
D17 VT332900 DIODE 1SS355 01
D19 VV833200 DIODE 1SS380 01
D20 VV307700 DIODE 1N4002S 01
D301 VT332900 DIODE 1SS355 BG 01
D302 VT332900 DIODE 1SS355 BG 01
D303 VT332900 DIODE 1SS355 BG 01
s F1 VS823000 FUSE T5A 125V JUCR 01
s F1 VT942800 FUSE 2A 250V TKABGL 01
s Fi1 WB754600 FLTR ELF15N030A
IC1 XL450A00 IC PQ05RA1 +5V 1.0A BG 03
IC101 X2874A00 IC M66003-0101FP FLD 08
IC261 XY549A00 IC TC74HC4051AFEL JUCRTKA 02
IC281 XW911A00 IC LA7108M VIDEO AMP JUCRTKA 04
IC282 XZ004A00 IC NJM2233BM JUCRTKA 03
IC301 X4258A00 IC BD3842FS-E2 BG
* IC303 XR866A00 IC BA7613N BG
* IC304 XR866A00 IC BA7613N BG
JK161 WB071300 JACK.MNI LGS6516-0100 03
L161 GE901970 COIL 68uH 01
PJ161 V6753000 JACK.PIN 3P
PJ201 V2069700 JACK.PIN 6P JUCRTKA 05
PJ221 VM725900 JACK.PIN 4P JUCRTKA 02
PJ222 V7189700 JACK.PIN 1P JUCRTKA 01
PJ241 V7189700 JACK.PIN 1P BG 01
PJ261 VV852500 JACK.PIN 3P JUCRTKA 03
PJ281 VV852500 JACK.PIN 3P JUCRTKA 03
PN1 V9637500 PIN L=70 #18
PN101 V9637500 PIN L=70 #18
PN161 V9637500 PIN L=70 #18
Q2 VP872700 TR 2SC4488 S,T 01
New Parts #
77
P.C.B. POWER
Schm
Q3 VV556400 TR 2SC2412K Q,R,S BG 01
Q5 VV556500 TR 2SA1037K Q,R,S BG 01
Q6 VV556400 TR 2SC2412K Q,R,S BG 01
Q7 VP872700 TR 2SC4488 S,T 01
Q8 VV556400 TR 2SC2412K Q,R,S BG 01
Q9 VV556500 TR 2SA1037K Q,R,S 01
s Q10 VR510800 TR 2SD2396 J,K 02
Q11 VV556400 TR 2SC2412K Q,R,S 01
Q12 VC218900 TR 2SC3330 R,S,T 01
s Q13 VG805300 TR 2SA1674 R,S 01
Q14 VV556400 TR 2SC2412K Q,R,S 01
Q15 VV556400 TR 2SC2412K Q,R,S 01
Q102 VV556400 TR 2SC2412K Q,R,S 01
Q103 VV556400 TR 2SC2412K Q,R,S 01
Q104 VD303700 TR 2SC3326 A,B 01
Q105 VD303700 TR 2SC3326 A,B 01
Q106 VV556400 TR 2SC2412K Q,R,S 01
Q108 VV556400 TR 2SC2412K Q,R,S 01
Q161 VV556400 TR 2SC2412K Q,R,S 01
Q162 VV556500 TR 2SA1037K Q,R,S 01
Q221 VD303700 TR 2SC3326 A,B JUCRTKA 01
Q222 VD303700 TR 2SC3326 A,B JUCRTKA 01
Q241 VD303700 TR 2SC3326 A,B BG 01
Q242 VD303700 TR 2SC3326 A,B BG 01
Q301 VV556400 TR 2SC2412K Q,R,S BG 01

Q302 VV556500 TR 2SA1037K Q,R,S BG 01
Q303 VV556400 TR 2SC2412K Q,R,S BG 01
Q304 VV556400 TR 2SC2412K Q,R,S BG 01
Q305 VV556500 TR 2SA1037K Q,R,S BG 01
Q306 VV556400 TR 2SC2412K Q,R,S BG 01
Q308 VV556400 TR 2SC2412K Q,R,S BG 01
Q309 VV556500 TR 2SA1037K Q,R,S BG 01
R21 HV753220 R.CAR.FP 2.2 1/4W 01
R28 HV755180 R.CAR.FP 180 1/4W 01
R29 HV756220 R.CAR.FP 2.2K 1/4W 01
s R30 VP940500 R.MTL.OXD 150 1W 01
s R31 VP940400 R.MTL.OXD 100 1W 01
s R34 V6730000 R.CAR. 2.2M 1/2W UC 01
R38 VP941500 R.MTL.OXD 4.7K 1W 01
s RY1 V6017400 RELAY DC SDT-S-112LMR2 04
ST241 V4040500 SCR.TERM M3 BG 01
SW51 VZ075500 SW.SLIDE SL14-22AM5F BG 03
SW101 V6091700 SW.RT.ENC XRE0122PVB25FINB-2 04
SW102 VV020300 SW.TACT SKQNAA 01
New Parts #
78
P.C.B. POWER & Chip Parts Chip Parts

Schm Schm
Ref. PART NO. Description Remarks Markets Rank Ref. PART NO. Description Remarks Markets Rank
*s T1 X4607A00 TRANS.PWR J RD355220 R.CHP 220 1/16W 01
*s T1 X4608A00 TRANS.PWR UC RD355270 R.CHP 270 1/16W 01
*s T1 X4609A00 TRANS.PWR R RD355330 R.CHP 330 1/16W 01
*s T1 X4610A00 TRANS.PWR TKL RD355470 R.CHP 470 1/16W 01
*s T1 X4611A00 TRANS.PWR A * RD355620 R.CHP 620 1/16W 01
*s T1 X4612A00 TRANS.PWR BG RD355680 R.CHP 680 1/16W 01
* TE71 WB966000 TERM.SP YKD21-5012Q PUSH RD355820 R.CHP 820 1/16W 01
s TH1 V7962300 THRMST.CHP NCP18WF104J03RB 01 RD355910 R.CHP 910 1/16W 01
U101 V8210200 L.DTCT GP1UD271XK 03 RD356100 R.CHP 1K 1/16W 01
U161 WB547900 L.DTCT 1P GP1FA513RZ 03 RD356120 R.CHP 1.2K 1/16W 01
* V101 WB569700 FL.DSPLY HNA-16SM08T RD356150 R.CHP 1.5K 1/16W 01
* WC255500 SHEET RD356180 R.CHP 1.8K 1/16W 01
V6203300 SPACER RD356200 R.CHP 2K 1/16W 01
* WB692100 SUPRT RD356220 R.CHP 2.2K 1/16W 01
RD356240 R.CHP 2.4K 1/16W 01
RD356270 R.CHP 2.7K 1/16W 01
RD356330 R.CHP 3.3K 1/16W 01
UF017470 C.EL.CHP 47uF 6.3V 01 RD356390 R.CHP 3.9K 1/16W 01
UF018100 C.EL.CHP 100uF 6.3V 01 RD356470 R.CHP 4.7K 1/16W 01
UF037100 C.EL.CHP 10uF 16V 01 RD356510 R.CHP 5.1K 1/16W 01
UF066220 C.EL.CHP 2.2uF 50V 01 RD356560 R.CHP 5.6K 1/16W 01
RD356680 R.CHP 6.8K 1/16W 01
US034470 C.CE.M.CHP 0.047uF 16V 01 RD356820 R.CHP 8.2K 1/16W 01
US060500 C.CE.CHP 5pF 50V 01 RD357100 R.CHP 10K 1/16W 01
US061100 C.CE.M.CHP 10pF 50V 01 RD357120 R.CHP 12K 1/16W 01
US064100 C.CE.M.CHP 0.01uF 50V 01 RD358220 R.CHP 220K 1/16W 01
US126100 C.CE.CHP 1uF 10V 01 RD359100 R.CHP 1M 1/16W 01
US135100 C.CE.CHP 0.1uF 16V 01
US135330 C.CE.CHP 0.33uF 16V 01
V3480600 C.CE.CHP 1uF 10V 01
RD350000 R.CHP 0 1/16W 01

RD353100 R.CHP 1 1/16W 01
RD353220 R.CHP 2.2 1/16W 01
RD354220 R.CHP 22 1/16W 01
RD354360 R.CHP 36 1/16W 01
* RD354430 R.CHP 43 1/16W 01
RD354470 R.CHP 47 1/16W 01
RD354750 R.CHP 75 1/16W 01
RD354820 R.CHP 82 1/16W 01
RD355100 R.CHP 100 1/16W 01
New Parts # New Parts #
79
A B C D E F G H I J
1
EXPLODED VIEW MECHANICAL PARTS
162 B, G models Schm
165
164 * 1-2 MFA08300 FLEXIBLE FLAT CABLE 8P 300mm P=1.0
101 162 103 * 1-3 MFA10100 FLEXIBLE FLAT CABLE 10P 100mm P=1.0
1-4 MF105100 FLEXIBLE FLAT CABLE 5P 100mm P=1.25 01
160
163 * 1-5 WB689800 FRONT PANEL SI J
8 (2) * 1-5 WB689400 FRONT PANEL SI UCRTKAL
2 * 1-5 WB689600 FRONT PANEL SI BG
* 1-6 WB690600 SUB PANEL SI
1-20 26 * 1-7 WB690000 PANEL, LID SI
8 (6) 8 (12) * 1-8 WB689300 SPRING, LID
1-8 29
1-9 131 8 (9) * 1-9 WB691000 BUTTON SI
1-20 164 * 1-10 WB690900 WINDOW PANEL, LID
* 1-11 WB691800 HINGE, LID SI
162 163 1-2 35 16 * 1-12 WB692800 PLATE, SP SI
1-13 1-3 * 1-13 WD075100 EARTH PLATE UCRTKABGL
8 (5) 17
1-4 1-20 EP630220 BIND HEAD P-TIGHT SCREW 3x8 MFZN2BL 01
3 1-40 1-5 106
161 1-21 VG893800 BIND HEAD P-TIGHT SCREW 2x6 MFZN2BL 01
20
103 1-40 V6034100 EMBLEM 03
1-12 1-13 18
* 5 WC277200 P.C.B. ASS'Y DIGITAL J
160 * 5 WC277300 P.C.B. ASS'Y DIGITAL UCRK
1-11 1-20 * 5 WC277500 P.C.B. ASS'Y DIGITAL TAL
160
1-10 * 5 WC277400 P.C.B. ASS'Y DIGITAL BG
1-7 (3) 8 160
* 6 WC276400 P.C.B. ASS'Y INPUT J
1-11
8 (4) * 6 WC276500 P.C.B. ASS'Y INPUT UC
1-6 162 * 6 WC276600 P.C.B. ASS'Y INPUT R
4 1-20 162 121 * 6 WC276700 P.C.B. ASS'Y INPUT TA
1-21 (1) 163 (11) 8 * 6 WC276800 P.C.B. ASS'Y INPUT K
7 (1) 8 * 6 WC276900 P.C.B. ASS'Y INPUT BG
163 (8) 8
167 * 6 WC277000 P.C.B. ASS'Y INPUT L
162 7 (2)
6 (2) * s 7 WC275400 P.C.B. ASS'Y MAIN
8 (10)
163 8 (7) * s 8 WC275600 P.C.B. ASS'Y POWER J
9
23 10 * s 8 WC275700 P.C.B. ASS'Y POWER UC
163 24
162 * s 8 WC275800 P.C.B. ASS'Y POWER R
167 21 28
134 * s 8 WC275900 P.C.B. ASS'Y POWER TK
5 9 22 * s 8 WC276000 P.C.B. ASS'Y POWER A
163
* s 8 WC276100 P.C.B. ASS'Y POWER BG
167 132 163
131 * s 8 WC276200 P.C.B. ASS'Y POWER L
155
135 7 (4) 9 WB877000 D-AMP MODULE UCD100W AMP MODULE 12
7 (3) 9 10 WB423900 AM/FM TUNER ENG04705Q J
166 25 5
168 * 10 WB424000 AM/FM TUNER ENG06709Q UCRTKL
15 105 163
168 * 10 WB424100 AM/FM TUNER ENG07711Q ABG
202 U, C, L, R, T, * s 15 X5009A00 POWER TRANSFORMER J
27 K, J models * s 15 X5010A00 POWER TRANSFORMER UC
163 * s 15 X5011A00 POWER TRANSFORMER R
6 166 * s 15 X5012A00 POWER TRANSFORMER TK
* s 15 X5013A00 POWER TRANSFORMER A
6 (1) * s 15 X5014A00 POWER TRANSFORMER BG
133
202 A, B, G models * s 15 X5015A00 POWER TRANSFORMER L
200 s 16 V2723100 POWER CABLE 1.8m J 07
* s 16 V9293500 POWER CABLE 2m UC
203 s 16 VN363200 POWER CABLE 2m R 04
120
s 16 VZ542500 POWER CABLE 2m T 05
* s 16 V8013000 POWER CABLE 2m K
162 s 16 V2296800 POWER CABLE 2m A
7
120 s 16 VV437300 POWER CABLE 2m B 08
200-1 204
162 New Parts #
80
Schm
* s 16 V9293600 POWER CABLE 2m GL
17 V2438700 CORD STOPPER 10P1 02
* 18 VB933800 FERRITE CORE BP53RB310190100A UCRTKABG
* 20 WC272400 DC FAN MOTOR DC D04R-24TM05(EX)
* 21 MFA40060 FLEXIBLE FLAT CABLE 40P 60mm P=1.0
* 25 WC588900 SUMI CARD 15P 70mm P=1.0
* 26 MFA15120 FLEXIBLE FLAT CABLE 15P 120mm P=1.0 BG
27 MF117070 FLEXIBLE FLAT CABLE 17P 70mm P=1.25
28 MF113100 FLEXIBLE FLAT CABLE 13P 100mm P=1.25 01
29 MF114070 FLEXIBLE FLAT CABLE 14P 70mm P=1.25 BG
35 VU590000 CABLE TIE CBTD001B
* 101 WB688100 TOP COVER SI
* 103 WB689100 REAR PANEL J
* 103 WB688400 REAR PANEL UC
* 103 WB688500 REAR PANEL R
* 103 WB688600 REAR PANEL T
* 103 WB688700 REAR PANEL K
* 103 WB688800 REAR PANEL A
* 103 WB689000 REAR PANEL BG
* 103 WB688900 REAR PANEL L
* 105 WB979700 SUPPORT/UCD
* 106 WB692500 COVER/FAN
* 120 WB690200 LEG
* 121 WB691400 KNOB D25.6 SI
* 131 WC838900 DAMPER 3/80/90
* 132 WB692600 SHEET/POWER
* 133 WB692700 SHEET/DIGITAL
* 134 WC654600 SHHET/BARRIER
135 V6773900 DAMPER/SIDE
155 VQ368600 PUSH RIVET P3555-B 01
160 VN413300 BIND HEAD BONDING B-T. SCREW 3x8 MFZN2BL 01
161 VV220300 BIND HEAD B-TIGHT SCREW 3x30 MFZN2BL 01
162 EP600250 BIND HEAD B-TIGHT SCREW 3x8 MFZN2Y 01
163 VT669300 PW HEAD B-TIGHT SCREW 3x8-8 MFC2 01
164 V5633800 TAPPING B-TITE SCREW 3x6-8 MFNI33
165 EP630210 BIND HEAD S-TIGHT SCREW 3x6 MFZN2BL BG 01
166 21991500 PW HEAD S-TIGHT SCREW 4x8-10 MFC2BL 01
167 EP600780 BIND HEAD B-TIGHT SCREW 4x8 MFC2BL 01
168 VY731200 BONDING HEAD TAPPING SCREW 3x10 MFNI33 01
ACCESSORIES
* 200 WB998500 REMOTE CONTROL RX-SL100 RRC4001-1507E JUCRTKA
* 200 WB998600 REMOTE CONTROL RX-SL100RDS RRC4001-1508E BG
200-1 AAX51940 BATTERY COVER 103RRS-141-04L 103RRS-141-04L
202 V6267000 INDOOR FM ANTENNA 1.4m 1pc JUCRTKL 03
202 VQ147100 INDOOR FM ANTENNA 1.4m 1pc ABG 02
203 WC192200 ANTENNA, AM LOOP 3083-100-0Y01 05
* 204 WC571300 CABLE TAG ASS'Y 6pairs/set
VH214900 BATTERY SUM-3N
New Parts #
81
A B C D E
1
REMOTE CONTROL
JP1 JP2
1 30
P0D2 P1A2
+
C1
3.0V 2 29
47F P0D3 P0D1
3 28
2 P1B0/INT P0D0
4 27
P0E0 P0C3
IC1: PD17242MC-129-5A4-E1-A
2 5 26
1 P0E1 P0C2
R1 SW1 3 6 25
2 (1/4W) P0E2 P0C1
D1
MIE554A2 7 24
P0E3 P0C0
6 AV STANDBY/ON SKIP () DOWN VOLUME (+) TV MUTE T3
R2 8 23
REM P0B3
27 5 TV STANDBY/ON SEARCH (+) UP AMP VIDEO 2
Q1 C2
9 22
2SD1781K-Q VDD P0B2
4 ENTER PAUSE DISPLAY MUTE TUNER
3 0.1F
10 21
XOUT P0B1
3 +10 SEARCH () RETURN TV VOL () DTV/CBL
X1 11 20
T1 XIN P0B0
4MHz 2 0 AUDIO MENU TV VOL (+) VIDEO 1
12 19
GND P0A3
1 9 STOP TITLE ENTER VCR TV CH ()
13 18
D2 RESETPU P0A2
SLEEP 8 REC SKIP (+) RIGHT DVD/CD TV CH ()
14 17
P1A0 P0A1
STANDBY/ON 7 CODE SET PLAY LEFT VOLUME () TV INPUT
C3 15 16
0.1F P1A1 P0A0
4 T2
NOT MOUNTED
82
RX-SL100 RX-SL100RDS Key CODE

Function
No. AMP TUNER
1 STANDBY/ON 7A-1F
2 SLEEP 7A-57
3 1 7A-88 7A-E5
4 2 7A-89 7A-E6
5 3 7A-8A 7A-E7
6 4 7A-8B 7A-E8
7 5 7A-8C 7A-E9
8 6 7A-8D 7A-EA
9 7 7A-8E 7A-EB
10 8 7A-8F 7A-EC
11 9 7A-90
12 0 7A-95
13 +10 7A-97
14 ENTER 7A-56
15 TV STANDBY/ON
16 AV STANDBY/ON
17 CODE SET
18 REC
19 STOP 7A-A4
20 AUDIO 7A-A5
21 SEARCH ()
22 PAUSE 7A-A6
23 SEARCH (+) 7A-A7
24 SKIP () 7A-12
25 PLAY 7A-11
26 SKIP (+) 7A-10
27 TITLE 7A-86
28 MENU 7A-9C
29 RETURN 7A-85
30 DISPLAY
31 UP 7A-98
32 DOWN 7A-99
33 LEFT 7A-53
34 RIGHT 7A-52
35 ENTER 7A-DE
36 TV VOL (+)
37 TV VOL ()
38 MUTE 7A-1C 7A-1C
39 AMP
40 VOLUME (+) 7A-1A 7A-1A
41 VOLUME () 7A-1B 7A-1B
42 DVD/CD 7A-C1
43 VCR 7A-0F
44 VIDEO 1 7A-13
45 DTV/CBL 7A-54
46 TUNER 7A-16
47 VIDEO 2 7A-55
48 TV MUTE
49 TV INPUT
50 TV CH ()
51 TV CH ()
83

Yamaha Rx-sl100 Sl100rds

Uploaded by

Copyright:

Available Formats

Yamaha Rx-sl100 Sl100rds

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Yamaha Rx-sl100 Sl100rds

Uploaded by

Copyright:

Available Formats

AV RECEIVER/AV AMPLIFIER

RX-SL100/RX-SL100RDS SERVICE MANUAL

2. Leakage Current Measurement (For 120V Models Only)

WARNING: CHEMICAL CONTENT NOTICE!

About Lead Free Solder /

Component Side / Foil Side /

Among some types of lead free solder currently available,

RX-SL100RDS (B, G models)

RX-SL100RDS (B, G models)

REMOTE CONTROL PANELS

* Specifications are subject to change without notice due

Set Menu Table /

The variable range of the parameter (Min/Max/Step) / //

Unit Pro Logic II / IIx Parameter Unit

C MAIN (4) P.C.B.

(Remove parts in the order as numbered.)

1. Removal of Top Cover (Fig. 1) 1. Fig. 1

2. Removal of Front Panel (Fig. 1) 2. Fig. 1

3. Removal of DIGITAL P.C.B. (Fig. 2) 3. DIGITAL P.C.B.Fig. 2

4. Removal of MAIN (1) ~ (4) and D-AMP Modules 4. MAIN14D-AMP MODULE

MAIN (3) P.C.B.

4 4 MAIN (2) P.C.B.

5. Removal of Rear Panel (Fig. 3) 5. Fig. 3

7. Removal of POWER (1) P.C.B. (Fig. 4) 7. POWER (1) P.C.B.Fig. 4

8. Removal of Power Transformer (Fig. 4) 8. Fig. 4

CB9 A Power (1) P.C.B.

When checking the P.C.B.: P.C.B.

INPUT (2) P.C.B.

SELF DIAGNOSIS FUNCTION (DIAG)

No DIAG menu sub-menu

7 DISPLAY CHECK 1. VFD CHECK (Initial display / )

No DIAG menu sub-menu

Starting DIAG in the protection cancel

Display provided when DIAG started

When there is no history of protection function: :

Opening message / DIAG menu display /

When there is a history of protection function: :

Cause: An excessive current flowed through the power

When there is a history of protection

Cause: DC output of the power amplifier is abnormal. DC

When there is a history of protection

Cause: The temperature of the UCD amplifier is excessive. UCD

Cause: Abnormal temperature of radiator

* Additional causes of protection can be due to loose CPU

History of protection function

Display during menu operation

Operation procedure of DIAG menu and

Initial settings used to start DIAG

Details of DIAG menu

SPEAKER OUTPUT (1 kHz) SUBWOOFER

YSS 0dB YSS 0dB

SPEAKER OUTPUT (1 kHz) SUBWOOFER

YSS Front 0dB YSS Front 0dB

YSS FULL BIT YSS FULL BIT

SPEAKER OUTPUT (1 kHz) SUBWOOFER

YSS FULL BIT F YSS FULL BIT F

RC/- C/LFE LS/RS L/R

Analog A/D AD or CS L/R

Main DSP Sub DSP